2.26 S OLENOID VALVES S ERIES VQ1000

Transcription

1 2.26 S OLENOID VALVES 5 PORT M ETAL S EAL/RUBBER S EAL U LTRA H IGH S PEED S OLENOID VALVE High Speed Response from new Solenoid Design. Long Life: Over 200 Million Cycles can be with Patent Pilot Valve design. Indicator light and Voltage Surge Suppressor Space Saving Design Five Options for Manifold Electrical Connection. Plug lead and Plug In valve manifold options. New cassette type manifold available. T ECHNICAL SPECIFICATIONS Type of Seal Metal Rubber Fluid Air, inert gas Air, inert gas Min Operating Pressure Single 0.MPa/4.5PSI 0.5MPa/22PSI Double 0.MPa/4.5PSI 0.MPa/4.5PSI 3-position 0.MPa/4.5PSI 0.2MPa/29PSI Max Operating Pressure (Note.) 0.75MPa/09PSI 0.75MPa/09PSI Effective Area Single 3.6 (0.2) 5.4 (0.3) (Cv Factor) mm 2 Double 3.6 (0.2) 5.4 ( position 3.6 (0.2) 5.4 (0.3) Response Time Single Max 2ms Max 5ms (Note 2). Double Max 0ms Max 5ms 3-position Max 20ms Max 25ms Life 200 million cycles or more Ambient and Fluid Temperature (Note 3) -0 to +50ºC (4~22ºF) -5 to +50ºC (23~22ºF) Lubricant (Note 4) Not required Not required Manual Override Non-locking, Push Non-locking, Push Protection Dustproof Dustproof (Note ) (Note 2) (Note 3) (Note 4) Contact SMC Customer Service for 45PSI (0 Bar). Calculated on the basis of JIS B (Supply pressure 0.5 MPa {5. bar}; the above valve shows reponse time checked when the valve is equipped with an indicator light and surge voltage suppressor). Use dry air to prevent dew condensation in the case when temperature is low. Perfect dry air (dew point equals to -30ºC) No grease on main valve. Special types (Contact SMC Customer Service for details and availability): i Pressure centre function ii External pilot iii Low power consumption (0.5W) iv Positive common wiring S OLENOID SPECIFICATIONS Coil Rated Voltage 2 VDC, 24 VDC 00/0 VAC Allowable Voltage + - 0% of Rated Voltage + - 0% of Rated Voltage Type of Coil Insulation Class B Class B Power Consumption (Note ) W Inrush/Holding:. VA (ma) Electrical Entry Plug In or Connector Type Plug In or Connector Type (Note ) Contact SMC for the low power consumption (0.5W) type. W IRING SPECIFICATIONS POSITIVE COM W IRING SPECIFICATIONS NEGATIVE COM (OPTION) S YMBOLS

2 S OLENOID VALVES 2.27 F K IT D-SUB CONNECTOR (25 PIN) The D-Sub Connector permits simple rationalization and installation labor saving for Electrical Connection. The D-Sub Connector (25-pin std., 5-pin option) conforms with MIL permitting use of commercial connectors with wide interchangeability. Top or Side Connector Receptacle Position can be selected in accordance with the available mounting space. Standard max 8 stations (Optional 6 stations possible). The total number of stations is tabulated starting from station one at the D side. P K IT (FLAT C ABLE C ONNECTION) MIL Flat Cable Connector permits simple rationalization and installation labor savings for Electrical Connection. The Connector (26 pin; 0-, 6-, and 20 pin optional) conforms with MIL spec permitting use of widely interchangeable commercial connectors. Top or Side Receptable Position can be selected in accordance with the available mounting space. Standard max 8 Stations (Optional 6 Stations optional). S EE INSIDE FRONT COVER FOR DETAILS OF YOUR LOCAL SALES OFFICE

3 2.28 S OLENOID VALVES T K IT (TERMINAL B LOCK B OARD) This Kit has a small Terminal Block inside a junction box. The Electrical Entry Port G (PF) /2 permits connection of Conduit Fittings. Max 2 Stations. B ODY P ORTED V ALVE - SINGLE U NIT VQ000 VQ C ONFIGURATION 2 Position single 2 2 Position double (latching) 3 3 Position closed centre 4 3 Position exhaust centre 5 3 Position pressure centre T YPE OF S EAL 0 Metal Rubber 6 0 N 5 L C6 S UBPLATE SUP CYLINDER P ORTS C3 One Touch Fittings for Ø3.2 C4 One Touch Fittings for Ø4 C6 One Touch Fittings for Ø6 M5 M5 (0-32Nom) N One Touch Fittings ø/8 N3 One Touch Fittings ø5/32 N7 One Touch Fittings ø/4 (Note) EXH Port is a Direct Exhaust Type (with Built In Silencer) M ANUAL O VERRIDE -.Non locking recessed type Note) B Locking tool type* *C Locking knob type Note) Locking type (B) is standard for double (latching) type. Indicate B in model no. Option P ILOT V ALVE S PECIFICATIONS (OPTION) - W Standard H.5W (High speed response) Y Low wattage type (Note) N Negative common wiring (Note): Except for 0 VAC type. E LECTRICAL E NTRY G Grommet (Except for latching type and 00/0VAC) L L type plug connector with lead wire LO L type plug connector without connector M M type plug connector with lead wire MO M type plug connector without connector C OIL R ATED V OLTAGE 3 0VAC 5 24VDC 6 2VDC

4 S OLENOID VALVES 2.29 B ASE M OUNTED T YPE P LUG I N U NIT VQ000 M A N I F O L D VV5Q 08 C6 F U N : VQ000 T YPE OF M ANIFOLD Plug In Unit - Base Mounted N UMBER O F S TATIONS 0 Station 6 6 Stations C YLINDER PORTS C3 One Touch Fittings for Ø3.2 C4 One Touch Fittings for Ø4 C6 One Touch Fittings for Ø6 M5 M5 (0-32Nom) N One Touch Fittings ø/8 N3 One Touch Fittings ø5/32 N7 One Touch Fittings ø/4 * Mixed Ports Available O PTION Symbol Option VQ000 (Blank) None B Check valve for prevention of back pressure D DIN Rail Mounted Type J With Vacuum Ejector Unit N With Nameplate R External Pilot capable S Built-in Silencer (Direct Exhaust) Note ) Note 2) Note 3) Note4) When more than one option is desired Combined symbols in alphabetical order. Example) BRS Models with a suffix -B have checked valves for prevention of back pressure at all manifold stations. In the case of the external pilot -R, order solenoid valves with the external pilot specification R. Contact SMC for details of vacuum ejector unit. Combination of ejector option J and nameplate N is not possible. Note) Note2) Insert code L (upward) or B (downward) for elbow type fittings for all manifold stations. Example) B6: Elbow one touch fittings for downward (bottom) piping. LM for models with elbow fittings and mixed cylinder port sizes. K IT ELECTRICAL ENTRY CABLE LENGTH S EE INSIDE FRONT COVER FOR DETAILS OF YOUR LOCAL SALES OFFICE

5 2.30 S OLENOID VALVES V A L V E VQ 0 0 N 5 M ANUAL O VERRIDE 0 VQ000 S YMBOLS *Option 2 Indicator light and surge voltage suppressor -.. Yes E...No 3 4 C OIL V OLTAGE 3 0VAC 5 24VDC 6 2VDC 5 T YPE OF S EAL 0 Metal Rubber P ILOT V ALVE S PECIFICATIONS - W (Standard) H.5W (High Speed response) Y Low wattage (0.5W) N Negative common (blank is positive common) ACCESSORIES MANIFOLD OPTIONS B LANKING PLATE ASSEMBLY VVQ000-0A-5 SUP BLOCK PLATE P VVQ000-6A- R PR N AMEPLATE [-N] VVQ000-N5-Station (-Max. stations) B UILT IN SILENCER Direct exhaust [-S] I NDIVIDUAL SUP SPACER VVQ000-P--C6 P LANKING PLUG 23 KQP STATIONS MATCHING FITTINGS ASSEMBLY VVQ000-52A-C8 (VQ000) INDIVIDUAL EXH SPACER VVQ000-R--C6 EXH BLOCK BASE ASSEMBLY - F - C3 VVQ000-9A- P - C4 - C6- (VQ000) L - - M5 N N3 N7 E LBOW FITTINGS ASSEMBLY C4 VVQ000-F-L- C6(VQ000) C3 M5 N N3 N7 S ILENCER (EXH PORT) V ACUUM EJECTOR UNIT VVQ000-J A BM (VQ000) C HECK VALVE FOR PREVENTION OF DIN RAIL MOUNTEDBRACKET [-D] OF BACK PRESSURE ASSEMBLY [-B] VVQ000-57A VVQ000-8A

6 S OLENOID VALVES 2.3 B ODY P ORTED T YPE P LUG L EAD U NIT/FLIP T YPE M A N I F O L D VV5Q 4 08 F S D VQ000 K IT T YPE OF M ANIFOLD 4 Plug in unit/flip type N UMBER O F S TATIONS 0 Station 6 6 Stations The number of stations differs from kit to kit. DIN RAIL/OPTION Symbol Option - None (C kit only) Note2) D DIN Rail Mounted Type N With Nameplate Note3) S Built-in Silencer (Direct Exhaust) Note ) Note 2) Note 3) When more than one option is desired Combined symbols in alphabetical order. Example) DNS All F, P, and S kits are of DIN rail mounted type.so include suffix D. F, P, and S kits are provided with an exhaust on one side while C kits are with an exhaust on both sides. K IT ELECTRICAL E NTRY C ABLE L ENGTH Note ) Note 2) The max. standard stations are 8. With single wiring arangement of up to 6 stations is possible. Specify the arrangement of stations using the manifold specification formfor more than 8 stations. Other than those above, F and P kits with different number of pins are available. S EE INSIDE FRONT COVER FOR DETAILS OF YOUR LOCAL SALES OFFICE

7 2.32 S OLENOID VALVES V A L V E VQ 4 0 Y 5 L C6 C YLINDER P ORTS C3 One Touch Fittings for Ø3.2 VQ000 C4 One Touch Fittings for Ø4 C6 One Touch Fittings for Ø6 C ONFIGURATION M5 M5 (0-32Nom) N One Touch Fittings ø/8 N3 One Touch Fittings ø5/32 N7 One Touch Fittings ø/4 2 M ANUAL O VERRIDE N OTE)3 N OTE)4 Standard model of a double (latching) type should be selected a push-locking type. Clearly write a symbol B oe C. A manual override for pilot valve is provided to the standard model for double type. N OTE)5 Note ) 3 position types need two stations Note ) F,P,T, and S kits need connector assembly when increasing the valve station. T YPE OF S EAL 0 Metal Rubber P ILOT V ALVE S PECIFICATIONS - W (Standard) H.5W (High pressure) Y Low wattage (0.5W) N Negative common Note) Except for AC and double (latching) type. C OIL V OLTAGE 3 0VAC (50/60Hz) 5 24VDC 6 2VDC Note ) The C kit is applicable to 200/220VAC. Contact SMC for other Kits. E LECTRICAL E NTRY G: grommet C kit single type only. (Except for AC). L: L type plug connector with lead wire L: O type plug connector without connector M: M type plug connector without connector MO: M type plug connector without connector Note ) LO and MO valves are used for F,P,T, and S kits. The plug connector and lead wire are attached to the manifold. ACCESSORIES MANIFOLD OPTIONS I NDIVIDUAL SUP SPACER VVQ000-P-4-C6 DIN RAIL M OUNTED B RACKET [-D] VVQ000-57A-4 I NDIVIDUAL EXH SPACER VVQ000-R-4-C6 B UILT I N S ILENCER, DIRECT E XHAUST [-S] N AMEPLATE [-N4] VVQ000-N4 Station (-Max. stations) S ILENCER (EXH PORT) AN03-X233 (VQ000) B LANKING P LUG KQP P R PR B LOCK V ALVE VQ P R- PR

8 S OLENOID VALVES 2.33 B ODY P ORTED T YPE P LUG L EAD U NIT/CASSETTE T YPE M A N I F O L D VV5Q 7 08 F U D VQ000 SUP/EXH PORT - Metric (mm) 00T Imperial (Inch) T YPE OF M ANIFOLD 7 Plug Lead unit/cassette type N UMBER O F S TATIONS 0 Station 6 6 Stations The number of stations differs from kit to kit. DIN RAIL/ OPTION Note ) Note 2) Note ) D N DIN rail mounted type With Nameplate Manifold is of a DIN rail mounted type, and so suffix D should be indicated. When the N option is desired, write as DN. K IT ELECTRICAL E NTRY C ABLE L ENGTH S EE INSIDE FRONT COVER FOR DETAILS OF YOUR LOCAL SALES OFFICE

9 2.34 S OLENOID VALVES V A L V E VQ000 C ONFIGURATION VQ 7 0 N 5 M C6 C YLINDER P ORTS C3 One Touch Fittings for Ø3.2 C4 One Touch Fittings for Ø4 C6 One Touch Fittings for Ø6 M5 M5 (0-32Nom) N One Touch Fittings ø/8 N3 One Touch Fittings ø5/32 N7 One Touch Fittings ø/4 Note ) The code is L for Elbow Piping for all Manifold Stations. Example L6: Elbow with One Touch Fittings. M ANUAL O VERRIDE Note ) Locking type (B) is used for the double (latching) type as standard. Must include B suffix. T YPE OF S EAL 0 Metal Rubber E LECTRICAL E NTRY L Type plug connector with lead wire LO Type plug connector without connector P ILOT V ALVE S PECIFICATIONS - W (Standard) H.5W (High Speed response) N Negative Common Note ) Y Low wattage (0.5W) Note) Except for 00/0VAC type. M Type plug connector with lead wire MO Type plug connector without connector C OIL V OLTAGE 3 0VAC 5 24VDC 6 2VDC With indicator light and surge voltage suppressor Note ) LO and MO valves are used for F,P, and S kits. Plug connector and lead wire layers are attached to the manifold. Note 2) Grommet type (G) is also available for C kit type. (Except for latching type and 00/0VAC) ACCESSORIES MANIFOLD OPTIONS SUP-EXH BLOCK P USH A SSEMBLY VVQ000-87A-B-50 N AMEPLATE [-N7] VVQ000-N7 Station (- Max. Stations) E LBOW F ITTINGS A SSEMBLY C3 VVQ000-F7-L C4 C6 B LANKING P LUG 23 KQP S ILENCER AN03-X233