4 Port Solenoid Valve Cassette Type Manifold Rubber Seal

Transcription

1 Port Solenoid Valve Cassette Type Manifold Rubber Seal 7.mm (SJ000) SJ000 SJ000 Can be mounted together. 0mm (SJ000) Connector connection New New cable type manifold is added! New Additional options are now available. SUP/EXH block assembly with regulator and pressure switch Valve with speed controller New An additional type of manual override is now available. ø ø ø6 Slide locking type 0mm ø connection is possible. type wiring manifold Vacuum release valve with restrictor Suction and release can be controlled with a single unit. Series SJ000/000 CAT.NAS-7C

2 Port Solenoid Valve Cassette Type Manifold Power consumption 0. W (SJ000 with power saving circuit) 0. W (SJ000 with power saving circuit) Service life of 0 million cycles or more (Based on SMC life test conditions) Connector type (Card edge type) Series SJ000 and SJ000 can be mounted together. Can easily increase or decrease stations and replace valves. pins connector allows up to 6 stations with double solenoids, stations with single solenoids. individual wiring compliant, too Card edge connector New Manifold uses halogen-free lead wires. cable type manifold Cable Piping variations With s Threaded type Threaded type is not available for (P), (E) port. With switch (Connector type) Possible to shut the signal of each valves individually. Manual operation is possible by switching OFF, even when the valve is in the energized state. ON OFF Switch The valve coil is kept in a deenergized state even when there is an electric signal from the manifold side connector, and this enables manifold operation. Manual locking Prevents wrong operation by sliding the switch to avoid a manual button from being pressed. Locked Unlocked Fittings are replaceable. Fittings (including type and size) can be easily changed by removing a clip. Clip etails P.99 Valve connection mechanism Connection between valves can be fixed by the valve lock switch. Connection can be confirmed with the connection hook inserted into the connection groove of the adjacent valve. Valve lock switch Connection hook FREE characters can be seen when connection is unlocked. Connector mounting direction Connecter mounting direction can be changed by sliding the switch. LOCK Switch FREE Light indication SOL.A: ON Orange SOL.B: ON Green Type of manual override Non-locking push type Push-turn locking slotted type New Slide locking type ON A side manual (Blue) B side manual (Yellow) OFF Features SOL.A SOL.B Manual button will hold the pushed (ON) status.

3 Series SJ000/000 PC wiring compliant Connector type only. -sub connector EX0 Integrated type (for output) serial transmission system Connector type only. Flat ribbon cable EX0 Gateway system serial transmission system Connector type only. EX0 Integrated type (for output) serial transmission system Connector type only. CC-Link ( outputs), evicenet (, 6 outputs) Easy attaching/detaching of the SI unit and wiring by the connector Separated valve power unit and transmission power unit/ensuring safety at maintenance Selectable between T-branch and straight type of communication connector SI unit Valve power unit Transmission power unit (for CC-Link) EX0 Gateway system serial transmission system Connector type only. Max. points (Input 6 points/ Output 6 points) All wires can be plugged into the connector units. CC-Link, evicenet, PROFIBUS-P compliant System configuration PLC Programmable Logic Controller Straight type Power supply GW (Gateway) Serial Transmission EX0 T-branch type Communication connector In case of evicenet, transmission power unit exists in the communication connector side of T-branch or straight type. position dual port valve Integrated to a single valve from -port valve Possible to control (A), (B) port individually. Can be mounted on the same manifold with a -port valve. Prepared types of combination Label with the same colors of the manual override is attached to show the functions of A side and B side. A side B side Symbol N.C. valve N.O. valve N.C. valve N.C. valve N.O. valve N.O. valve (A) (EA) (P) (A) (EA) (P) (A) (EA) (P) (B) (EB) (B) (EB) (B) (EB) Input unit Input unit Including SI unit manifold valve Input unit Input unit Output unit A side coil B side coil B side manual A side manual Including SI unit manifold valve Including SI unit manifold valve B side passage symbol A side passage symbol Features

4 COM COM Port Solenoid Valve Cassette Type Manifold Regulator block etails P.7 This is a regulator block with the same width (0 mm) as the SJ000. Pressure supplied from the side is used to reduce pressure in the manifold. The valves are all depressurized from the regulator block. Regulator block Pneumatic circuit (example of regulator block installation) (B) (A) (Pilot passage) (SJ60) 0. MPa (B) (A) (SJ60) Regulator block Set to 0. MPa (SJ P) (B) (A) (SJ60) 0. MPa (B) (A) (SJ60) P port 0. MPa applied (E) (P) side side Note) Reduces supply pressure from the side of the manifold. Supply pressure from the cannot be reduced. Both the pressure gauge mounting position and the method of operating the pressure adjustment screw can be selected. SJ P(-H) SJ000-0-P(-H) With manual operation of the pressure adjustment screw SJ000-M-P(-H) 9 psi = 0. MPa, 7 psi = 0. MPa 0. MPa P port 0. MPa FREE side LOCK Pressure gauge, top mounting Pressure gauge, side mounting Without pressure gauge Regulator block Intermediate connector block assembly This connector block can be used by inserting it into the middle of the manifold. This can be used, for example, when you wish to separate electrical control of valves in the same manifold, or when the number of control points is insufficient. The assembly is also compatible with PC wiring with the power supply terminal. etails P.79 Intermediate connector block assembly Intermediate connector block assembly wiring example Intermediate connector block Connector block side side FREE side ouble solenoid (Station ) Features ouble solenoid (Station ) Station Station ouble solenoid (Station ) ouble solenoid (Station ) Station Station The solenoid valves can be controlled from the position where the intermediate connector block assembly is mounted. Intermediate connector block assembly LOCK

5 Series SJ000/000 New SUP/EXH block assembly with regulator and pressure switch This pressure regulator is intended to adjust the SUP pressure of the manifold. Additionally, pressure switch and pressure gauge can be mounted. etails P.7 SUP/EXH block assembly with regulator and pressure switch Lateral handle New Upward handle Valve with speed controller etails P.7 As a speed controller is built-into this valve, the cylinder speed can be adjusted on the valve side. Two types, meter-in and meter-out, are set. Valve with speed controller Meter-in: Black Meter-out: Silver Pneumatic circuit (Installation example of SUP/EXH block assembly with regulator and pressure switch, valve with speed controller) Valve with speed controller SUP/EXH block assembly with regulator and pressure switch side (B) (A) (B) (A) (B) (A) (B) (A) (B) (A) (E) (P) (Pilot passage) (SJ60) (SJ60-S) (SJ60-S0) (SJ60) (SJ60) (SJ000B-PCB) Features

6 Vacuum Release Valve with Restrictor Two spool valves are built-in. Vacuum suction and release can be controlled with a single valve. New Connector connection Cable connection Restrictor Flow rate adjustment of release air Prevents workpiece blow-off. Manual PS port: Pressure detection port (M x 0.) Slotted locking type Filter Eliminates foreign matter on vacuum and release side. Replaceable (B) Vacuum pad port (P) Release pressure port (E) Vacuum pressure port wiring variations <Connector connection> -sub connector Serial (EX0) Flat ribbon cable Serial (EX0) PC wiring <Cable connection> -sub connector Flat ribbon cable Series SJA6 Power consumption 0. W (with power saving circuit) Width: 0 mm (same size as Series SJ000) Equipped with restrictor to enable flow rate adjustment of release air. Replaceable filters are built-in on the vacuum and release sides. Equipped with a pressure detection port enabling connection of a pressure switch, etc. Can be combined with port solenoid valve, Series SJ000/000 (Made to Order). (Consult SMC for details.) Enables -system pressure switching where the (P) port and (E) are set to different positive pressures. (In this case, flow can be adjusted on the P-port side only.) (E) Vacuum pressure port Vacuum pressure switching valve Adsorbing and Transferring System Circuit Example X Filter Vacuum side (B) Vacuum pad port Filter Release side (P) Release pressure port SJA6 Release pressure switching valve (Built-in restrictor) Features

7 INEX Manifold Variations P. Port Solenoid Valve Series SJ000/000 Specifications P. P.6 SJ Specifications Connector Type Manifold P. Manifold Manifold P.60 -sub Connector/Flat Ribbon Cable/PC How to Order/Connector Type P. How to Order/ P.7 Manifold Electrical /Connector Type, P.9 imensions/connector Type, P. PC System with Power Supply Terminal How to Order/Connector Type P. Manifold Electrical /Connector Type P. imensions/connector Type P.6 EX0 Integrated Type (for Output) Serial Transmission System How to Order/Connector Type P. imensions/connector Type P. EX0 Gateway System Serial Transmission System How to Order/Connector Type P.9 imensions/connector Type P. Manifold Exploded View/Connector Type, P.6, 7 How to Increase Manifold Stations/Connector Type, P., 9 How to Order P.6 imensions P.6 Manifold Exploded View/ P.6 Manifold Options Made to Order Manifold Options P.69 Made to Order P.0 SJA6 Vacuum Release Valve with Restrictor Series SJA6 Connector Type Manifold Manifold P. Specifications P. P. -sub Connector/Flat Ribbon Cable/PC / Serial (EX0/EX0) How to Order/Connector Type P. How to Order/ P.7 imensions/connector Type, P.9 Manifold Exploded View/Connector Type, P.9, 9 Specifications/ Manifold How to Order P.9 imensions P.9 Manifold Exploded View/ P.9 Specific Product Precautions P.96 Front matter

8 Manifold Variations Port Solenoid Valve Series SJ000/000 Parallel wiring Connection method Serial wiring Vacuum Release Valve with Restrictor Series SJA6 Manifold type Items -sub connector Flat ribbon cable connector PC wiring PC wiring (With power supply terminal) EX0 (For output) EX0 (Gateway system) wiring Connector Type Note ) SSJ/-60 port solenoid valve New SSJ/-60L P. P. P. P. P. P.9 P.7 P.7 P.6 P. P. P.0 SSJ/-60- P.6 Connector Type Note ) Vacuum release valve with restrictor New SSJ-60 SSJ-60L SSJ-60- P. P. P. P. P. P. P.7 P.7 P.6 P.9 Note ) A linkage printed circuit board is built-into the individual wiring valve so as to combine with the plug-in type. Note ) Specify the required specifications in the manifold specification sheet. Note ) The all single wiring or all double wiring can be specified.

9 Mixed wiring Single/ouble Mixed type M60 SJ000/000 ifferent pressure pneumatic circuit diagram/ Block disk assembly Blanking block assembly Manifold options ual flow fitting Regulator block SUP/EXH block assembly with regulator and pressure switch Valve with speed controller Intermediate connector block assembly Increase of manifold stations Series SJ000/000 Solenoid valve specifications Voltage suppressor Non-polar Series SJA6 +/ common Polar With power saving circuit With individual switch Main valve fluororubber specifications SJ Specifications Note ) Note ) P. P.69 P.70 P.7 P.7 P.7 Note ) P.7 P.79 P. P.0 Note ) P.69 P.70 Note ) P.7 Note ) Note 6) P.7 P.9 P.0 Manifold Options P.6 P.69 P.70 Note ) P.7 P.7 P.7 Note ) P.7 P. P.0 Made to Order SJA6 Note ) P.69 P.70 P.79 P. P.0 Specifications/ Note ) P.69 P.70 Note 6) P.9 P.0 Note ) P.69 P.70 P. P.0 Note ) The vacuum release valve uses only the double wiring. Note ) Only SJ000 size is provided. Note 6) Adding additional station is possible up to the maximum number of stations.

10 Manifold Specifications Port Solenoid Valve Series SJ000/000 Specifications Model Manifold type (P: SUP), (E: EXH) Valve stations Applicable connector Internal wiring (A), (B) port Location piping spec. irection (P), (E) port Port size (A), (B) SJ000 port SJ000 Note ) Weight W (g) n: Number of SUP/EXH blocks m: Weight of IN rail -sub connector Type 60F Connector type/ Cable type ( ) Connector type: to stations Cable type: to 0 stations -sub connector Conforming to MIL-C-0 JIS-X-0 Type 60P Connector type/ Cable type ( ), Connector type/cable type Flat ribbon cable connector Socket: 6 pins MIL type with strain relief Conforming to MIL-C-0 Flat ribbon cable Serial wiring wiring Type 60PG Connector type/ Type 60PH Type 60S Type 60S6B ( Cable type ) Connector type/ EX0/ EX0/ Type 60 Type 60J (Connector type) ( Cable type ) ( Connector type) ( Connector type) Type 60G (Connector type) to stations(type PG) to 6 stations(type J, Type G) Flat ribbon cable connector Socket: 0 pins MIL type with strain relief Conforming to MIL-C-0 SUP, EXH Flat ribbon cable connector Socket: 0 pins MIL type with strain relief Conforming to MIL- C-0, Connector type to stations to stations to 6 stations to 0 stations Connector type: non-polar, positive common, negative common/cable type: positive common, negative common Valve Horizontal, Upward, ownward (Using elbow fittings for upward or downward) C6, C, N7, N9 (Inch size elbow fitting is not available.) C, C, N, N, M C, C, C6, N, N, N7, M W = n + m + Note ) When many valves are operated simultaneously, use B type (SUP/EXH both sides), applying pressure to the (P) ports on both sides and exhaust from the (E) ports on both sides. Note ) The weight W is the value for the -sub connector manifold only with internal pilot, SUP/EXH block straight fittings specifications. To obtain the weight with solenoid valves attached, add the solenoid valve weights given on page for the appropriate number of stations. Refer to page 7 for the weight of IN rail. (Please contact SMC for the weight of external pilot specifications, elbow fittings.) Flow Characteristics SJ000 (P) (E) C SJ000 (P) (E) C Port size Port size, (A, B) C C M, (A, B) C C C6 M C[dm /(s bar)] C[dm /(s bar)] / (P A/B) b / (P A/B) b Note) The value is for manifold base with stations and individually operated position type. Please contact SMC for position dual port valves. Cv Cv Flow characteristics Flow characteristics C[dm /(s bar)] C[dm /(s bar)] / (A/B E) b / (A/B E) b Cv Cv

11 Specifications Series SJ000/000 SJ sub connector Flat ribbon cable PC wiring Solenoid Valve Specifications Fluid Internal pilot operating pressure range psi (MPa) External pilot operating pressure range psi (MPa) position single position dual port valve position double position Operating pressure range Pilot position single pressure position double range position Ambient and fluid temperature to F ( 0 to 0 C) (No freezing) position single, double Maximum operating 0 position dual port valve frequency (Hz) position Non-locking push type Manual override (Manual operation) Push-turn locking slotted type Internal pilot Main and pilot valve common exhaust Pilot exhaust method External pilot Pilot valve individual exhaust Lubrication Not required Mounting orientation Unrestricted Impact/Vibration resistance (m/s ) 0/0 Enclosure ustproof Note) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Value in the initial state) Vibration resistance: No malfunction occurred in one sweep test between and 000Hz. Test was performed to axis and right angle directions of the main valve when pilot signal is ON and OFF. (Value in the initial state) Solenoid Specifications Air to 0 (0. to 0.7). to 0 (0. to 0.7) 9 to 0 (0. to 0.7). to 0 ( 00 kpa to 0.7) 6 to 0 (0. to 0.7) Specifications Manifold Options Made to Order EX0 Integrated type (for output) serial transmission system EX0 Gateway system serial transmission system wiring Coil rated voltage Allowable voltage fluctuation Power consumption (W) Surge voltage suppressor iode Indicator light LE For the allowable voltage fluctuation for Z and T types (with power saving circuit), please observe the following range because they have voltage drop due to internal circuit. Z type VC: 7% to +0% VC: % to +0% T type VC: % to +0% VC: 6% to +0% Response Time Standard With power saving circuit (Continuous duty type) VC, VC ±0% of rated voltage SJ SJ SJ SJ Response time ms (at 7 psi (0. MPa)) Type of actuation SJ000 SJ000 position single 6 or less 6 or less position double 0 or less 0 or less position or less or less position dual port valve 0 or less 0 or less Note) Based on dynamic performance test, JIS B 7-9. (Coil temperature: 6 F (0 C), at rated voltage) SJA6 Specifications/

12 Weight Model/SJ000 Port Solenoid Valve Series SJ000/000 Specifications Valve model Type of actuation Single position ouble Closed center SJ 60-C position Exhaust center Pressure center position ual port valve Single position ouble Closed center SJ 60-C position Exhaust center Pressure center position ual port valve Single position ouble Closed center SJ 60-M position Exhaust center Pressure center position ual port valve Note) Please contact SMC for the weight of elbow fittings. Connector iagram Port size (A), (B) C ø Onetouch ( ) fitting C ø Onetouch ( ) fitting M x 0. Weight (g) Model/SJ000 Valve model Type of actuation Single position ouble Closed center SJ 60-C position Exhaust center Pressure center position ual port valve Single position ouble Closed center SJ 60-C position Exhaust center Pressure center position ual port valve Single position ouble Closed center SJ 60-C6 position Exhaust center Pressure center position ual port valve Single position ouble Closed center SJ 60-M position Exhaust center Pressure center position ual port valve Note) Please contact SMC for the weight of elbow fittings. Port size (A), (B) C ø Onetouch ( ) fitting C ø Onetouch ( ) fitting C6 ø6 Onetouch ( ) fitting M x 0. Weight (g) For both serial and parallel wiring, additional valves are sequentially assigned pins on the connector. This makes it completely unnecessary to disassemble the connector unit. Single solenoid and double solenoid Solenoid Connector side (-sub connector, etc.) (+, ) Unused terminal Station Station Station ouble solenoid Station Single solenoid with double wiring spec. Single solenoid (ouble wiring spec.) Station ouble solenoid Station Solenoid Connector side (-sub connector, etc.) (+, ) Station Station Station ouble solenoid Station Single solenoid Station ouble solenoid Station Mounting a valve with individual wiring (+) Solenoid Connector side (-sub connector, etc.) (+, ) Station Station Station Single solenoid Station ouble solenoid Station wiring (M type) Station ouble solenoid Station

13 SJ000: Connector Type Symbol Series SJ000/000 position single position single with back pressure check valve position single o t r e w y q! u!0 SJ Specifications (A) (B) (A) (B) (A) (EA) (P) (EB) position double position double with back position double pressure check valve (A) (B) (EA) (P) (EB) (A) (B) o t r (EA)/(EB) e w (P) y q i! u (B)!0 (EA) (P) (EB) (EA) (P) (EB) (A) (B) (EA)/(EB) (P) position closed center position exhaust center position closed center/exhaust center/pressure center (A) (B) (A) (B) i o t r e w y q! u!0 Manifold Options Made to Order (EA) (P) (EB) position pressure center (EA) (P) (EB) (A) SJA6 Component Parts No. escription Material Note Resin/HNBR Spool valve assembly position solenoid valve: Aluminum/HNBR Body Adapter plate Pilot adapter Pilot valve assembly Body cover Port block Bottom cover Light cover Zinc die-cast Resin Resin Resin Resin Resin Resin White White White White White Light blue Replacement Parts No. 0 (A) escription Clip (B) (EA) (P) (EB) Part no. Refer to the part no. on page 99. SJ000-CL- (0 pcs.) (EA)/(EB) (P) (EA)/(EB) (P) i SJ60K with back pressure check valve o t r e w y q! u i!0 (A) (B) (B) Specifications/ 6

14 SJ000: Connector Type Series SJ000/000 Symbol position dual port valve SJA60 [N.C. valve x ] SJA60K with back pressure check valve SJA60 [N.C. valve x ]!0 y t r q e u q! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) (EA)/(EB) (P) o SJB60 [N.O. valve x ] SJB60K with back pressure check valve SJB60 [N.O. valve x ]!0 y t r w e u w! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) (EA)/(EB) (P) o SJC60 [N.C., N.O. valve x (each)] SJC60K with back pressure check valve SJC60 [N.C. valve, N.O. valve x (each)]!0 y t r q e u w! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) Component Parts No. escription Material Note Spool valve assembly Spool valve assembly Body Adapter plate Pilot adapter Pilot valve assembly Body cover Port block Bottom cover Light cover Resin/HNBR Resin/HNBR Zinc die-cast Resin Resin Resin Resin Resin Resin N.C. (Normally closed) N.O. (Normally open) White White White White White Light blue Replacement Parts 7 No. escription Clip Part no. Refer to the part no. on page 99. SJ000-CL- (0 pcs.) (EA)/(EB) (P) (EA)/(EB) (P) o SJA60K with back pressure check valve!0 y t r q e u q! i o! (A) (B)

15 Series SJ000/000 SJ SJ000: Connector Type Symbol position single position single with back pressure check valve (A) (B) (A) (B) position single o t r e w y q! u!0 (A) Specifications (EA) (P) (EB) position double (A) (B) (EA) (P) (EB) position double with back pressure check valve (A) (B) (EA)/(EB) position double o t r e w y (P) q i! u (B)!0 (EA) (P) (EB) (EA) (P) (EB) (A) (B) (EA)/(EB) (P) i Manifold Options position closed center position exhaust center (A) (B) (A) (B) position closed center/exhaust center/pressure center o t r e w y q! u!0 Made to Order Component Parts No. escription Material Note Resin/HNBR Spool valve assembly position solenoid valve: Aluminum/HNBR Body Adapter plate Pilot adapter Pilot valve assembly Body cover Port block Bottom cover Light cover Zinc die-cast Resin Resin Resin Resin Resin Resin White White White White White Light blue Replacement Parts No. 0 (EA) (P) (EB) position pressure center (A) escription Clip (B) (EA) (P) (EB) (EA) (P) (EB) Part no. Refer to the part no. on page 99. SJ000-CL- (0 pcs.) (EA)/(EB) (P) (EA)/(EB) (P) i SJ60K with back pressure check valve o t r e w y q! u i!0 (A) (B) (A) (B) SJA6 Specifications/

16 SJ000: Connector Type Series SJ000/000 Symbol position dual port valve SJA60 [N.C. valve x ] SJA60K with back pressure check valve SJA60 [N.C. valve x ]!0 y t r q e u q! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) (EA)/(EB) (P) o SJB60 [N.O. valve x ] SJB60K with back pressure check valve SJB60 [N.O. valve x ]!0 y t r w e u w! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) (EA)/(EB) (P) o SJC60 [N.C., N.O. valve x (each)] SJC60K with back pressure check valve SJC60 [N.C. valve, N.O. valve x (each)]!0 y t r q e u w! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) Component Parts No. escription Material Note Replacement Parts 9 No. Spool valve assembly Spool valve assembly Body Adapter plate Pilot adapter Pilot valve assembly Body cover Port block Bottom cover Light cover escription Clip Resin/HNBR Resin/HNBR Zinc die-cast Resin Resin Resin Resin Resin Resin N.C. (Normally closed) N.O. (Normally open) White White White White White Light blue Part no. Refer to the part no. on page 99. SJ000-CL- (0 pcs.) (EA)/(EB) (P) (EA)/(EB) (P) o SJA60K with back pressure check valve!0 y t r q e u q! i o! (A) (B)

17 Series SJ000/000 SJ SJ000: Symbol position single position single with back pressure check valve (A) (B) (A) (B) position single o t r e w y q! u!0 (A) Specifications (EA) (P) (EB) (EA) (P) (EB) (B) position double (A) (B) position double with back pressure check valve (A) (B) (EA)/(EB) (P) position double o t r e w y q! u!0 i (EA) (P) (EB) (EA) (P) (EB) (A) (B) Manifold Options position closed center position exhaust center No. 0 (A) (B) (EA) (P) (EB) position pressure center (A) (B) (EA) (P) (EB) Component Parts Replacement Parts escription Clip (A) (B) (EA) (P) (EB) No. escription Material Note Resin/HNBR Spool valve assembly position solenoid valve: Aluminum/HNBR Body Adapter plate Pilot adapter Pilot valve assembly Body cover Port block Bottom cover assembly Light cover Zinc die-cast Resin Resin Resin Resin Resin Resin White White White White White Light blue Part no. Refer to the part no. on page 99. SJ000-CL- (0 pcs.) (EA)/(EB) (P) position closed center/exhaust center/pressure center o t r e w y q! u!0 (EA)/(EB) (P) SJ60K with back pressure check valve o t r e w y q! u!0 (EA)/(EB) (P) i i (A) (B) (A) (B) i 0 Made to Order SJA6 Specifications/

18 SJ000: Symbol position dual port valve SJA60 [N.C. valve x ] Series SJ000/000 SJA60K with back pressure check valve SJA60 [N.C. valve x ]!0 y t r q e u q! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) (EA)/(EB) (P) o SJB60 [N.O. valve x ] SJB60 [N.O. valve x ] SJB60K with back pressure check valve!0 y t r w e u w! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) (EA)/(EB) (P) o SJC60 [N.C., N.O. valve x (each)] SJC60K with back pressure check valve SJC60 [N.C. valve, N.O. valve x (each)]!0 y t r q e u w! i! (A) (B) (A) (B) (A) No. (EA) (P) Component Parts Replacement Parts escription Clip (EB) (EA) (P) (EB) No. escription Material Note Spool valve assembly Spool valve assembly Body Adapter plate Pilot adapter Pilot valve assembly Body cover Port block Bottom cover assembly Light cover Resin/HNBR Resin/HNBR Zinc die-cast Resin Resin Resin Resin Resin Resin N.C. (Normally closed) N.O. (Normally open) White White White White White Light blue Part no. Refer to the part no. on page 99. SJ000-CL- (0 pcs.) (EA)/(EB) (P) (EA)/(EB) (P) o (B) SJA60K with back pressure check valve!0 y t r q e u q! i! o (A) (B)

19 Series SJ000/000 SJ SJ000: Symbol position single position single with back pressure check valve (A) (B) (A) (B) position single o t r e w y q! u!0 Specifications (EA) (P) (EB) (EA) (P) (EB) (A) (B) position double (A) (B) position double with back pressure check valve (A) (B) (EA)/(EB) (P) position double o t r e w y q! u!0 i (EA) (P) (EB) (EA) (P) (EB) (A) position closed center position exhaust center (A) (B) (EA) (P) (EB) position pressure center (A) (B) (EA) (P) (EB) (EA)/(EB) (P) (B) position closed center/exhaust center/pressure center i o t r e w y q! u!0 Manifold Options Made to Order SJA6 No. 0 (A) (B) (EA) (P) (EB) Component Parts No. escription Material Note Resin/HNBR Spool valve assembly position solenoid valve: Aluminum/HNBR Body Adapter plate Pilot adapter Pilot valve assembly Body cover Port block Bottom cover assembly Light cover Zinc die-cast Resin Resin Resin Resin Resin Resin White White White White White Light blue Replacement Parts escription Clip Part no. Refer to the part no. on page 99. SJ000-CL- (0 pcs.) (EA)/(EB) (P) SJ60K with back pressure check valve o t r e w y q! u!0 (EA)/(EB) (P) i (A) (B) (A) (B) i Specifications/

20 SJ000: Symbol position dual port valve SJA60 [N.C. valve x ] Series SJ000/000 SJA60K with back pressure check valve SJA60 [N.C. valve x ]!0 y t r q e u q! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) (EA)/(EB) (P) o SJB60 [N.O. valve x ] SJB60K with back pressure check valve SJB60 [N.O. valve x ]!0 y t r w e u w! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) (EA)/(EB) (P) o SJC60 [N.C., N.O. valve x (each)] SJC60K with back pressure check valve SJC60 [N.C. valve, N.O. valve x (each)]!0 y t r q e u w! i! (A) (B) (A) (B) (A) (EA) (P) (EB) (EA) (P) (EB) (B) Component Parts No. escription Material Note Spool valve assembly Spool valve assembly Body Adapter plate Pilot adapter Pilot valve assembly Body cover Port block Bottom cover assembly Light cover Resin/HNBR Resin/HNBR Zinc die-cast Resin Resin Resin Resin Resin Resin N.C. (Normally closed) N.O. (Normally open) White White White White White Light blue Replacement Parts No. escription Clip Part no. Refer to the part no. on page 99. SJ000-CL- (0 pcs.) (EA)/(EB)!0 y t r q e u q! i! (EA)/(EB) (P) (P) o SJA60K with back pressure check valve o (A) (B)

21 P. Connector Type Manifold Manifold Series SJ000/000 Connector Type Manifold -sub Connector/Flat Ribbon Cable/PC SJ Specifications Manifold P.7 P. -sub Connector/Flat Ribbon Cable Connector Type Manifold PC System with Power Supply Terminal Manifold Options Made to Order SJA6 P. Connector Type Manifold EX0 Integrated Type (for Output) Serial Transmission System P.9 Connector Type Manifold EX0 Gateway System Serial Transmission System Specifications/

22 Connector Type -sub Connector/Flat Ribbon Cable/PC Series SJ000/000 Connector type manifold SSJ Series SJ000 SJ000 (SJ000/000 mixed) Mixed mounting type Nil Standard Note ) M Mixed mounting Note ) Note ) There is no need to enter anything when you operate either the SJ000 or SJ000 series alone. Note ) Enter M when the SJ000 or SJ000 series will be mounted on the same manifold base together. Connector type F: -sub connector ( pins) How to Order Manifold Assembly Ordering example (SSJ-60P- ) How to Order 60 F 0 U Connector mounting position Symbol Mounting position Connector entry side direction : Upward : Lateral ouble solenoid, individual wiring/lead wire length 00 mm ( VC) SJ60-MZ-C6 ( set) ouble solenoid, with switch ( VC) SJ60-CZJ-C6 ( set) ouble solenoid ( VC) SJ60-CU-C6 ( sets) Single solenoid ( VC) SJ60-CU-C6 ( sets) SSJ-60P set (Manifold part no.) SJ60-CU-C6... sets (Single solenoid part no.) SJ60-CU-C6... sets (ouble solenoid part no.) SJ60-CZJ-C6... set (ouble solenoid, with switch part no.) SJ60-MZ-C6... set (ouble solenoid, individual wiring/lead wire length 00 mm part no.) The asterisk denotes the symbol for assembly. Prefix to the part no. of the solenoid valve, etc. The valve arrangement is numbered as the st station from side. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. In the case of complex arrangement, specify them in the manifold specification sheet. Note) When ordering a manifold, specify the part nos. of valves to be mounted together. (An order cannot be placed with only the manifold part no.) Stations P: Flat ribbon cable (6 pins) side PG: Flat ribbon cable (0 pins) PH: Flat ribbon cable (0 pins) SUP/EXH block ( side mounting) J: PC wiring (0 pins) PCW type Nil With external pilot spec. X, PE port Elbow fitting (Upward) L With external pilot spec. X, PE port Elbow fitting (ownward) B With external pilot spec. X, PE port There is no need to enter anything when the SUP/EXH block mounting position M is selected. Pilot spec. Nil Internal pilot S Internal pilot/built-in silencer R External pilot RS External pilot/built-in silencer There is no need to enter anything when the SUP/EXH block mounting position M is selected. For built-in silencers, the (E) ports are plugged. SUP/EXH block mounting position Valve stations F: -sub connector Symbol 0 Stations station stations Note Up to solenoids possible. PG: Flat ribbon cable (0 pins) Symbol Stations Note 0 station Up to solenoids stations possible. U B M The number of the blanking block assembly is also included. Since single and double wiring are available with the blanking block assembly, select a model compatible with the valve wiring spec. planned for the future. (Refer to page 70.) An order cannot be placed with only the manifold part no. Be sure to order solenoid valves for mounting at the same time while referring to the ordering example. IN rail length specified Nil Standard length stations Specify a longer rail than the stations standard length. Specify the valve stations not exceeding the maximum stations. SUP/EXH block fitting spec. Straight fitting ( to 0 stations) side ( to 0 stations) Both sides ( to stations) Special specifications P: Flat ribbon cable (6 pins) Symbol 0 Stations station stations Note Up to solenoids possible. PH: Flat ribbon cable (0 pins) Symbol Stations Note 0 station Up to solenoids 0 stations possible. J: PC wiring (0 pins) Symbol 0 6 Stations station 6 stations Note Up to 6 solenoids possible. Specify the required specifications (including port sizes other than ø) by means of the manifold specification sheet. Refer to page through to 0 for PC wiring type with power supply terminal.

23 Connector Type -sub Connector/Flat Ribbon Cable/PC Series SJ000/000 SJ A B C Type of actuation position single solenoid position double solenoid position closed center position exhaust center position pressure center ual port valve: N.C./N.C. ual port valve: N.O./N.O. ual port valve: N.C./N.O. Refer to pages 6 through to for the Symbol. Nil Standard With switch wiring Note) [For plug-in mixed mounting] Note) Refer to pages 6 and 6 for the dedicated non plug-in individual wiring. Coil spec. Standard SJ SJ With power saving circuit T (Continuous duty type) Be sure to select with power saving circuit when the solenoid valve will be energized continuously for long period. SJ Series SJ000 SJ000 Nil R Connector entry C: edicated for centralized wiring How to Order Solenoid Valves 60 C U C6 60 C Z J C6 60 M Z C6 Pilot spec. Internal pilot External pilot External pilot spec. is not applicable for position dual port valves. Back pressure check valve Nil None K Built-in Back pressure check valve is not applicable for position valve. With switch Rated voltage VC 6 VC specifications Nil Positive common N Negative common For the non-polar type, there is no need to select a symbol. Light/surge voltage suppressor With light/surge voltage suppressor U (Non-polar type) With light/surge voltage suppressor Z (Polar type) When the types with power saving circuit, with switches, and individual wiring are used, the nonpolar type cannot be selected. Single solenoid Nil A, B port size Straight (Metric size) C: ø C: ø C6: ø6 (SJ000 only) (Inch size) N: ø/" N: ø/" N7: ø/" (SJ000 only) M: M x 0. (SJ000 only) M: M x 0. (SJ000 only) wiring spec. Single wiring ouble wiring There is no need to enter anything for position double, position and position solenoid valves. Select this when the unused numbers to wiring are set. Refer to page for details. Specifications Manifold Options Made to Order M: wiring, With lead wire Length 00 mm MN: wiring, Without lead wire (With connector, socket) MO: wiring, Without connector With linkage printed circuit board With linkage printed circuit board With linkage printed circuit board Connector entries with the symbol M can not use the switch signal from the common wiring on the manifold. For details, refer to Connector iagram on page. When ordering a connector assembly separately, refer to pages 0 and 0. Manual override Nil: Non-locking push type : Push-turn locking slotted type F: Slide locking type Elbow fitting assembly (Upward entry) (Metric size) L: ø elbow fitting assembly L: ø elbow fitting assembly L6: ø6 elbow fitting assembly (SJ000 only) (Inch size) LN: ø/" elbow fitting assembly LN: ø/" elbow fitting assembly LN7: ø/" elbow fitting assembly (SJ000 only) Elbow fitting assembly (ownward entry) (Metric size) B: ø elbow fitting assembly B: ø elbow fitting assembly B6: ø6 elbow fitting assembly (SJ000 only) (Inch size) BN: ø/" elbow fitting assembly BN: ø/" elbow fitting assembly BN7: ø/" elbow fitting assembly (SJ000 only) Protective class class # (Mark: ) 6 SJA6 Specifications/

24 -sub Connector/Flat Ribbon Cable Series SJ000/000 How to Order An order cannot be placed with only the manifold part no. Be sure to order solenoid valves for mounting at the same time while referring to the ordering example. Cable type manifold SSJ F: -sub connector ( pins) PG: Flat ribbon cable (0 pins) Stations Series SJ000 SJ000 Connector mounting position Symbol Mounting position side Connector type P: Flat ribbon cable (6 pins) PH: Flat ribbon cable (0 pins) side SSJ-60LP set (Manifold part no.) SJ60-FZ-C6... sets (Single solenoid part no.) SJ60-FZ-C6... sets (ouble solenoid part no.) The asterisk denotes the symbol for assembly. Prefix to the part no. of the solenoid valve, etc. The valve arrangement is numbered as the st station from side. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. In the case of complex arrangement, specify them in the manifold specification sheet. Note) When ordering a manifold, specify the part nos. of valves to be mounted together. (An order cannot be placed with only the manifold part no.) 60L F 0 U Cable type Connector entry direction : Upward : Lateral Nil S How to Order Manifold Assembly 7 Ordering example (SSJ-60LP) ouble solenoid ( VC) SJ60-FZ-C6 ( sets) Manifold wiring spec. All double wiring Note ) All single wiring Note ) Note ) All double wiring: -position single, double, -position and -position valves can be used on all manifold stations. Note ) All single wiring: Available only for the manifold which has -position single for all stations. Note that -position double, - or -position valves cannot be used. Note ) If a mixture of single wiring and double wiring is required, it is available as a special order. Single solenoid ( VC) SJ60-FZ-C6 ( sets) SUP/EXH block ( side mounting) 0 0 SUP/EXH block mounting position U B M SUP/EXH block fitting spec. Nil L B ( to 0 stations) side ( to 0 stations) Both sides ( to 0 stations) Special specifications Specify the required specifications (including port sizes other than ø) by means of the manifold specification sheet. Valve stations F: -sub connector ( pins) Symbol Stations Note 0 stations All double wiring 0 stations stations All single 0 0 stations wiring PH: Flat ribbon cable (0 pins) Symbol Stations Note 0 stations stations stations stations All double wiring All single wiring IN rail length specified Nil Standard length stations Specify a longer rail than the 0 0 stations standard length. Specify the valve stations not exceeding the maximum stations. Straight fitting With external pilot spec. X, PE port: Elbow fitting Elbow fitting (Upward) With external pilot spec. X, PE port: Straight fitting Elbow fitting (ownward) With external pilot spec. X, PE port: Elbow fitting There is no need to enter anything when the SUP/EXH block mounting position M is selected. P: Flat ribbon cable (6 pins) Symbol 0 Stations stations Note All double wiring stations stations 0 stations Pilot spec. Nil Internal pilot Internal pilot/ S Built-in silencer R External pilot External pilot/ RS Built-in silencer There is no need to enter anything when the SUP/EXH block mounting position M is selected. All single wiring PG: Flat ribbon cable (0 pins) Symbol Stations Note 0 stations stations stations stations All double wiring All single wiring The number of the blanking block assembly is also included. The cable type is applicable to or more stations.

25 -sub Connector/Flat Ribbon Cable Series SJ000/000 SJ A B C How to Order Solenoid Valves SJ 60 F Z C6 Series SJ000 SJ000 Type of actuation position single solenoid position double solenoid position closed center position exhaust center position pressure center ual port valve: N.C./N.C. ual port valve: N.O./N.O. ual port valve: N.C./N.O. Refer to pages 6 through to for the Symbol. Nil T Nil R Pilot spec. Internal pilot External pilot External pilot spec. is not applicable for position dual port valves. Coil spec. Standard With power saving circuit (Continuous duty type) Be sure to select with power saving circuit when the solenoid valve will be energized continuously for long period. Connector entry F: edicated for centralized wiring, cable type Nil: Non-locking push type Back pressure check valve Nil None K Built-in Back pressure check valve is not applicable for position valve. Rated voltage VC 6 VC : Push-turn locking slotted type Nil N specifications Positive common Negative common Light/surge voltage suppressor Z With light/surge voltage suppressor Manual override F: Slide locking type A, B port size Straight (Metric size) C: ø C: ø C6: ø6 (SJ000 only) (Inch size) N: ø/" N: ø/" N7: ø/" (SJ000 only) M: M x 0. (SJ000 only) M: M x 0. (SJ000 only) Elbow fitting (Upward entry) (Metric size) L: ø elbow fitting L: ø elbow fitting L6: ø6 elbow fitting (SJ000 only) (Inch size) LN: ø/" elbow fitting LN: ø/" elbow fitting LN7: ø/" elbow fitting (SJ000 only) Elbow fitting (ownward entry) (Metric size) B: ø elbow fitting B: ø elbow fitting B6: ø6 elbow fitting (SJ000 only) (Inch size) BN: ø/" elbow fitting BN: ø/" elbow fitting BN7: ø/" elbow fitting (SJ000 only) Specifications Manifold Options Made to Order SJA6 Specifications/ Protective class class # (Mark: )

26 Series SJ000/000 Manifold Electrical /Connector Type (Non-polar Type) Type 60F: -sub connector ( pins) Type 60P: Flat ribbon cable (6 pins) Type 60PG: Flat ribbon cable (0 pins) Station Station 6 Station Station Station 9 Station Station Station Note) This circuits are for the specifications with up to stations of position double, position and position dual port valve. There should be wired in order without skipping or leaving any connectors remaining. Triangle mark Station Station Note) This circuits are for the specifications with up to stations of position double, position and position dual port valve. There should be wired in order without skipping or leaving any connectors remaining. Triangle mark Station Station Note) This circuits are for the specifications with up to 9 stations of position double, position and position dual port valve. There should be wired in order without skipping or leaving any connectors remaining. Type 60PH: Flat ribbon cable (0 pins) Type 60J: Flat ribbon cable (0 pins, PC wiring) Triangle mark Station Station Station Note) This circuits are for the specifications with up to stations of position double, position and position dual port valve. There should be wired in order without skipping or leaving any connectors remaining Station Station Station Station Station Station 6 Station 7 Station Triangle mark Terminal no Note ) This circuits are for the specifications with up to stations of position double, position and position dual port valve. There should be wired in order 0 6 without skipping or leaving any connectors remaining. Note ) For details on PC wiring system, refer to PC System catalog (CAT.E0-0). Caution When the non-polar U type valves are used, either positive common or negative common wiring of the manifold is possible. However, when the Z type valves are used, select the positive common or negative common according to the wiring specifications. 9

27 Manifold Electrical / Type 60LF: -sub connector ( pins) Station Station SJ 000 -sub Connector/Flat Ribbon Cable/PC 000 Type 60LP: Flat ribbon cable (6 pins) 6 Station Station Series SJ000/000 Type 60LPG: Flat ribbon cable (0 pins) Station 9 Station Specifications Station Station Station Station Triangle mark Station Station Triangle mark Note) This circuit is for the all double wiring specifications with up to 0 stations. Note) This circuit is for the all double wiring specifications with up to 0 stations. Note) This circuit is for the all double wiring specifications with up to 9 stations. Manifold Options Type 60LPH: Flat ribbon cable (0 pins) 0 Made to Order 9 SJA6 7 Station Specifications/ Note) This circuit is for the all double wiring specifications with up to stations. Caution Triangle mark Station Station When the non-polar U type valves are used, either positive common or negative common wiring of the manifold is possible. However, when the Z type valves are used, select the positive common or negative common according to the wiring specifications. 0

28 Series SJ000/000 imensions: Series SJ000 for -sub Connector SSJ-60F - Stations.6. U(S, R, RS) (Pitch) P=7. [External pilot spec.]. PE LOCK FREE (7.) 9. (6.) 0 (7).. 6. Silencer (Air discharge port) (Built-in silencer spec.) (9.) Switch for locking a connector () (L) (.) (.6) (Connector entry direction upward) (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" 0. (X: External pilot port) Applicable tubing O.: ø, ø/" Applicable connector: -sub {JIS-X-0, MIL-C-0} equivalent [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" Valve lock switch M x 0. [(A), (B) port] side X IN rail Terminal no. Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) x M.6 x No.-0UNC [(A) and (B) ports are in inches.] IN rail holding screw (Station n) (Station ) Manual override switch Light/surge voltage suppressor : Orange : Green. Slide locking type ( manual override ).9 FREE SSJ-60LF - Cable connection 0 OFF OFF ON ON 7.. (.9) LOCK Height to manual override Push type manual override: 0. Locking type manual override: 0. Switch (When equipped with switch) L: imensions n: Stations L n Note) For manifold dimensions including elbow fitting, refer to page. L L L

29 -sub Connector Series SJ000/000 SJ imensions: Series SJ000 for -sub Connector SSJ-60F -.6 Stations B(S, R, RS) (Pitch) P=7... [External pilot spec.] (There is a piping of X, PE port in the both sides.) Specifications [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" M x 0. [(A), (B) port] (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" Valve lock switch Switch for locking a connector () (L) side (Connector entry direction upward) (X: External pilot port) Applicable tubing O.: ø, ø/" Applicable connector: -sub {JIS-X-0, MIL-C-0} equivalent (7.). FREE LOCK 7. (9.) (6.) 0 (7) PE Manifold Options IN rail 0 IN rail holding screw Light/surge voltage suppressor : Orange : Green (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow Manual override L (IN rail mounting hole pitch:.) L (Station n) (Station ). Slide locking type ( manual override ) OFF OFF ON ON.9. (When equipped with switch) 9.9 (For individual wiring) 7.. (.9) Terminal no. Approx. 00 (Lead wire length) Silencer (Air discharge port) (Built-in silencer spec.) Manual override switch SSJ-60LF - Cable connection x M.6 x No.-0UNC [(A) and (B) ports are in inches.] FREE LOCK. X Made to Order SJA6 Specifications/ Height to manual override Push type manual override: 0. Locking type manual override: 0. Switch (When equipped with switch) Note) For manifold dimensions including elbow fitting, refer to page. L: imensions n: Stations n L L L L

30 Series SJ000/000 imensions: Series SJ000 for -sub Connector SSJ-60F - Stations.6. U(S, R, RS) (Pitch) P = 0 [External pilot spec.].6.. [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" M x 0. [(A), (B) port] PE LOCK FREE (6.) 0 (7).. 6. Silencer (Air discharge port) (Built-in silencer spec.) Switch for locking a connector (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" C6:. ( N7: 0.6 ) (9.) Valve lock switch () side (L) (.) C6: 9.6 ( N7:. ) (Connector entry direction upward) Applicable connector: -sub {JIS-X-0, MIL-C-0} equivalent Terminal no. X IN rail Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) x M.6 x No.-0UNC [(A) and (B) ports are in inches.] IN rail holding screw (Station n) (Station ) Manual override switch Light/surge voltage suppressor : Orange : Green. Slide locking type ( manual override ).9 SSJ-60LF - Cable connection FREE 0 LOCK OFF ON OFF ON (.9). 7. Height to manual override Push type manual override: 0. Locking type manual override: 0. Switch (When equipped with switch) L: imensions n: Stations L n L L L Note) For manifold dimensions including elbow fitting, refer to page.

31 -sub Connector Series SJ000/000 SJ imensions: Series SJ000 for -sub Connector SSJ-60F -.6 Stations B(S, R, RS) (Pitch) P = 0.. [External pilot spec.] (There is a piping of X, PE port in the both sides.) Specifications [(P), (E) port] Applicable tubing O.: ø, ø/6" C6:. ( N7: 0.6 ) [(A), (B) port] Applicable tubing O.: ø, ø/" Valve lock switch ø, ø/" ø6, ø/" M 0. [(A), (B) port] Switch for locking a connector () (L) side (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" (Connector entry direction upward) Applicable connector: -sub {JIS-X-0, MIL-C-0} equivalent. IN rail FREE LOCK (9.) (6.) 0 (7) PE Manifold Options 0 IN rail holding screw Light/surge voltage suppressor : Orange : Green Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) (Station n). L Slide locking type ( manual override ) OFF ON (Station ) OFF ON.9. (When equipped with switch) 9.9 (For individual wiring) Manual override switch (.9). 7. Approx. 00 (Lead wire length) Silencer (Air discharge port) (Built-in silencer spec.) Terminal no. SSJ-60LF - Cable connection x M.6 x No.-0UNC [(A) and (B) ports are in inches.] FREE LOCK. X Made to Order SJA6 Specifications/ Height to manual override Push type manual override: 0. Locking type manual override: 0. Switch (When equipped with switch) Note) For manifold dimensions including elbow fitting, refer to page. L: imensions n: Stations n L L L L

32 Series SJ000/000 imensions: SJ000/000 Mixed Manifold SSJ-M60F - (9.).6 [(P), (E) port] Applicable tubing O.: ø, ø/6". Stations U(S, R, RS) [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" SJ000 pitch P = 0 Switch for locking a connector SJ000 pitch P = 7..(SJ000) [.(SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" side L ().(SJ000) [(SJ000)] (9.6)(SJ000) [(7.)(SJ000)] L dimension: Formula, L to L = 7. x n + 0 x n + 7. M = ( + 9.9)/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ + n: Quantity of SJ000 n: Quantity of SJ000 The dimensions of L to L for SSJ-M60F/- Stations are the same as those of SSJ-M60F/- Stations U. Applicable connector: -sub {JIS-X-0, MIL-C-0} equivalent LOCK FREE IN rail IN rail holding screw Manual override (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) 7.(SJ000) [7.(SJ000)] Terminal no. x M.6 x No.-0UNC [(A) and (B) ports are in inches.] (Connector entry direction upward) L SSJ-M60F - (9.).6 [(P), (E) port] Applicable tubing O.: ø, ø/6" B(S, R, RS) [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/". IN rail Stations SJ000 pitch P = 0 side L Switch for locking a connector () SJ000 pitch P = 7. FREE LOCK.(SJ000) [(SJ000)] (9.6)(SJ000).(SJ000) [(7.)(SJ000)] [.(SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" L dimension: Formula, L to L = 7. x n + 0 x n + 7. M = ( + 9.9)/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ + n: Quantity of SJ000 n: Quantity of SJ000 Applicable connector: -sub {JIS-X-0, MIL-C-0} equivalent IN rail holding screw Manual override (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L 7.(SJ000) [7.(SJ000)] Terminal no. x M.6 x No.-0UNC [(A) and (B) ports are in inches.] (Connector entry direction upward)

33 imensions: Series SJ000 for Flat Ribbon Cable/PC P SSJ-60 J - Stations.6. -sub Connector/Flat Ribbon Cable/PC U(S, R, RS) (Pitch) P = 7. Series SJ000/000 [External pilot spec.] SJ Specifications [(P), (E) port] Applicable tubing O.: ø, ø/6" (7.) (9.) Silencer (Air discharge port) (Built-in silencer spec.) [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" Valve lock switch M x 0. [(A), (B) port] Switch for locking a connector () (L) side (.) (.6) (PE: Pilot EXH port) 0. Applicable tubing O.: ø, ø/" (X: External pilot port) (Connector entry direction upward) Applicable tubing O.: ø, ø/" Applicable connector: 6 pin MIL type with strain relief (MIL-C-0 compliant) 6.. FREE LOCK 9. (6.) 0 (7) 6. PE X Manifold Options IN rail 0 L: imensions n: Stations L n L L L Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow IN rail holding screw (Station n) Light/surge voltage suppressor : Orange : Green Height to manual override Push type manual override: 0. Locking type manual override: 0. L (IN rail mounting hole pitch:.) L. Slide locking type ( manual override ) (Station ) OFF OFF ON ON. 7. (When equipped with switch) 9.9 (For individual wiring) Manual override switch () Switch (When equipped with switch) Note ) Type 60PG, 60PH and 60J differ only in their connectors, and the L through L dimensions are the same as type 60P. Note ) For manifold dimensions including elbow fitting, refer to page. Approx. 00 (Lead wire length) Applicable connector: 0 pin MIL type with strain relief (MIL-C-0 compliant) LOCK Triangle mark location In case of PC wiring Applicable connector: 0 pin MIL type with strain relief (MIL-C-0 compliant) Triangle mark location Triangle mark location PG In case of 60 J (0 pins) In case of 60PH (0 pins) SSJ-60LP - Cable connection. 6 Made to Order SJA6 Specifications/

34 Series SJ000/000 imensions: Series SJ000 for Flat Ribbon Cable/PC P SSJ-60 J - Stations.6 B(S, R, RS) (Pitch) P = 7... [External pilot spec.] (There is a piping of X, PE port in the both sides.).6. [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" Switch for locking a connector M x 0. [(A), (B) port] PE LOCK FREE 9. (6.) 0 (7).. 6. (7.) Valve lock switch () (L) side (9.) (PE: Pilot EXH port) 0. Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" (Connector entry direction upward) Applicable connector: 6 pin MIL type with strain relief (MIL-C-0 compliant) 6.. X L (IN rail mounting hole pitch:.) L (). (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) Triangle mark location Applicable connector: 0 pin MIL type Applicable connector: 0 pin MIL type with strain relief with strain relief (MIL-C-0 compliant) (MIL-C-0 compliant) () IN rail IN rail holding screw Manual override switch Light/surge voltage suppressor : Orange : Green Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow (Station n). Slide locking type ( manual override ) Silencer (Air discharge port) (Built-in silencer spec.) (Station ) 0 OFF OFF ON ON 7. Height to manual override Push type manual override: 0. Locking type manual override: 0. SSJ-60LP - Cable connection LOCK Switch (When equipped with switch) Triangle mark location In case of 60 (0 pins) PG J In case of PC wiring Triangle mark location In case of 60PH (0 pins) Note ) Type 60PG, 60PH and 60J differ only in their connectors, and the L through L dimensions are the same as type 60P. Note ) For manifold dimensions including elbow fitting, refer to page. L: imensions n: Stations n L L L L

35 imensions: Series SJ000 for Flat Ribbon Cable/PC P SSJ-60 J - Stations.6 U(S, R, RS). (Pitch) P = 0 Flat Ribbon Cable/PC Series SJ000/000 [External pilot spec.] SJ Specifications.6 [(P), (E) port] Applicable tubing O.: ø, ø/6" C6:. ( N7: 0.6 ) (9.). M x 0. [(A), (B) port] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" Valve lock switch. Switch for locking a connector () (L) side (.) C6: 9.6 ( N7:. ).. 6. (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (Connector entry direction upward) (X: External pilot port) Applicable tubing O.: ø, ø/" Applicable connector: 6 pin MIL type with strain relief (MIL-C-0). FREE LOCK 9. (6.) 0 (7) 6. PE X Manifold Options IN rail Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw Light/surge voltage suppressor : Orange : Green 0 Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L: imensions n: Stations n L L L L L (IN rail mounting hole pitch:.) (Station n) Height to manual override Push type manual override: 0. Locking type manual override: 0. L OFF ON (Station ) OFF ON 7.. (When equipped with switch) 9.9 (For individual wiring) Manual override switch () Switch (When equipped with switch) Note ) Type 60PG, 60PH and 60J differ only in their connectors, and the L through L dimensions are the same as type 60P. Note ) For manifold dimensions including elbow fitting, refer to page.. Slide locking type ( manual override ) Approx. 00 (Lead wire length) Triangle mark location PG In case of 60 J (0 pins) Triangle mark location Applicable connector: 0 pin MIL type Applicable connector: 0 pin MIL type with strain relief with strain relief (MIL-C-0) (MIL-C-0) In case of PC wiring Triangle mark location In case of 60PH (0 pins) SSJ-60LP - Cable connection FREE LOCK. Made to Order SJA6 Specifications/

36 Series SJ000/000 imensions: Series SJ000 for Flat Ribbon Cable/PC P SSJ-60 J - Stations.6 B(S, R, RS) (Pitch) P = 0.. [External pilot spec.] (There is a piping of X, PE port in the both sides.).6.. [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" M x 0. [(A), (B) port] (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" (Connector entry direction upward) PE LOCK FREE 9. (6.) 0 (7).. 6. C6:. ( N7: 0.6 ) Switch for locking a connector Valve lock switch () (L) side (9.) Applicable connector: 6 pin MIL type with strain relief (MIL-C-0 compliant). 7. X Silencer (Air discharge port) (Built-in silencer spec.) L (IN rail mounting hole pitch:.) L () IN rail IN rail holding screw Manual override switch Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow (Station n) Light/surge voltage suppressor : Orange : Green. Slide locking type ( manual override ) (Station ). (When equipped with switch) 9.9 Switch (When equipped with switch) (For individual wiring) Approx. 00 (Lead wire length) Triangle mark location Applicable connector: 0 pin MIL type Applicable connector: 0 pin MIL type with strain relief with strain relief (MIL-C-0 compliant) (MIL-C-0 compliant) 0 OFF ON OFF ON 7. Height to manual override Push type manual override: 0. Locking type manual override: 0. LOCK FREE SSJ-60LP - Cable connection In case of PC wiring Triangle mark location PG In case of 60 J (0 pins) Triangle mark location In case of 60PH (0 pins). Note ) Type 60PG, 60PH and 60J differ only in their connectors, and the L through L dimensions are the same as type 60P. Note ) For manifold dimensions including elbow fitting, refer to page. L: imensions n: Stations n L L L L

37 imensions: SJ000/000 Mixed Manifold P SSJ-M60 J - (9.) (9.)..6 [(P), (E) port] Applicable tubing O.: ø, ø/6". IN rail holding screw.6 U(S, R, RS) Manual override (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" IN rail IN rail holding screw SJ000 pitch P = 0 [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" IN rail P SSJ-M60 J - Stations Stations Switch for locking a connector SJ000 pitch P = 0 B(S, R, RS) Switch for locking a connector FREE LOCK SJ000 pitch P = 7. FREE LOCK side L () side L () Manual override (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L 7.(SJ000).(SJ000) [(SJ000)] [7.(SJ000)].(SJ000) [(SJ000)] 7.(SJ000) (9.6)(SJ000) [(7.)(SJ000)] [7.(SJ000)] (9.6)(SJ000) (SJ000) [.(SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" SJ000 pitch P = 7. Flat Ribbon Cable/PC.(SJ000) [.(SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" [(7.)(SJ000)] Series SJ000/000 L dimension: Formula, L to L = 7. x n + 0 x n + 7. M = ( + 0.6)/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ +. Applicable connector: 6 pin MIL type with strain relief (MIL-C-0) Triangle mark location (Connector entry direction upward) n: Quantity of SJ000 n: Quantity of SJ000 The dimensions of L to L for SSJ-M60P/- Stations are the same as those of SSJ-M60P/- Stations U. L dimension: Formula, L to L = 7. x n + 0 x n + 7. M = ( + 0.6)/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ +. Applicable connector: 6 pin MIL type with strain relief (MIL-C-0) Triangle mark location (Connector entry direction upward) n: Quantity of SJ000 n: Quantity of SJ000 0 SJ Specifications Manifold Options Made to Order SJA6 Specifications/

38 Series SJ000/000 imensions: Series SJ000 with Elbow Fittings SSJ-60F - Stations U L B.6. (Pitch) P = 7. [External pilot spec.] LOCK (.) FREE.7 (.9) 0.9 (.9).9 (6) 0. (.) [(P), (E) port] Applicable tubing O.: ø Inch sizes for elbow fittings are not available. (E) port (P) port [(B), (A) port] Applicable tubing O.: ø, ø/" ø, ø/" (B) port (A) port [SUP/EXH block (External pilot spec.)]. 0 (Station n) (Station ) 7... (7.6). (PE: Pilot EXH port) Applicable tubing O.: ø (X: External pilot port) Applicable tubing O.: ø side L SSJ-60LF - Stations U B Cable type SSJ-60LF - Stations L U B Cable type (.) [Valve]. (A) port ownward (B type) [SUP/EXH block (External pilot spec.)] (B) port (7.) (E) port.7 (6) (7.7) (7) (6.) 0 9. (P) port

39 imensions: Series SJ000 with Elbow Fittings SSJ-60F - Stations.6. U -sub Connector/Flat Ribbon Cable/PC L B (Pitch) P = 0 Series SJ000/000 [External pilot spec.] SJ Specifications (.9) 0.9 (.9).9 [(P), (E) port] Applicable tubing O.: ø Inch sizes for elbow fittings are not available. (E) port (P) port LN7: 6.9 L6:. LN7: 9. ( L6: 7. ) ( ) Made to Order LN7:.6 L6:. LN7: 6. L6: Manifold Options (7.6). (PE: Pilot EXH port) Applicable tubing O.: ø 0. [(B), (A) port] side Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" (B) port [SUP/EXH block (External pilot spec.)] (A) port (X: External pilot port) Applicable tubing O.: ø 6. SJA6 LOCK (.) FREE (Station n) (Station ). SSJ-60LF - Stations L U B Cable type 7. BN7:0.6 B6:. [Valve] (A) port BN7: 7.7 ( B6: 0. ) (B) port ownward (B type) [SUP/EXH block (External pilot spec.)] BN7:6. B6:.6 BN7: 9 ( B6: 6. ) L SSJ-60LF - Stations U B Cable type.. 6. (P) port 0. (7.) (7) (E) port 0 (6.).7 (7.7) 9. Specifications/

40 Connector Type PC System with Power Supply Terminal Series SJ000/000 Connector type manifold SSJ Series SJ000 SJ000 (SJ000/000 mixed) Mixed mounting type Nil Standard Note ) M Mixed mounting Note ) Note ) There is no need to enter anything when you operate either the SJ000 or SJ000 series alone. Note ) Enter M when the SJ000 or SJ000 series will be mounted on the same manifold base together. How to Order Manifold Assembly Ordering example (SJ000) SUP/EXH block ( mounting) Stations 60 G Connector type Flat ribbon cable (0 pins) Connector mounting position Symbol Mounting position side ouble solenoid, individual wiring/lead wire length 00 mm ( VC) SJ60-MZ-C6 ( set) ouble solenoid, with switch ( VC) SJ60-CZJ-C6 ( set) side ouble solenoid ( VC) SJ60-CU-C6 ( sets) PCW type Single solenoid ( VC) SJ60-CU-C6 ( sets) SSJ-60G-06U... set (Manifold part no.) SJ60-CU-C6... sets (Single solenoid part no.) SJ60-CU-C6... sets (ouble solenoid part no.) SJ60-CZJ-C6... set (ouble solenoid, with switch part no.) SJ60-MZ-C6... set (ouble solenoid, individual wiring/lead wire length 00 mm part no.) The asterisk denotes the symbol for assembly. Prefix to the part no. of the solenoid valve, etc. The valve arrangement is numbered as the st station from side. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. In the case of complex arrangement, specify them in the manifold specification sheet. Note) When ordering a manifold, specify the part nos. of valves to be mounted together. (An order cannot be placed with only the manifold part no.) How to Order 0 U SUP/EXH block mounting position U ( to 0 stations) side ( to 0 stations) B Both sides ( to 6 stations) M Special specifications Specify the required specifications (including port sizes other than ø) by means of the manifold specification sheet. Valve stations Symbol Stations 0 station 6 An order cannot be placed with only the manifold part no. Be sure to order solenoid valves for mounting at the same time while referring to the ordering example. 6 stations Note Up to 6 solenoids possible. The number of the blanking block assembly is also included. Since single and double wiring are available with the blanking block assembly, select a model compatible with the valve wiring spec. planned for the future. (Refer to page 70.) IN rail length specified Nil Standard length 6 stations 6 stations Specify a longer rail than the standard length. Specify the valve stations not exceeding the maximum stations. SUP/EXH block fitting spec. Straight fitting Nil With external pilot spec. X, PE port Elbow fitting (Upward) L With external pilot spec. X, PE port Elbow fitting (ownward) B With external pilot spec. X, PE port There is no need to enter anything when the SUP/EXH block mounting position M is selected. PCW type PCW type PCW type Pilot spec. Nil Internal pilot S Internal pilot/built-in silencer R External pilot RS External pilot/built-in silencer There is no need to enter anything when the SUP/EXH block mounting position M is selected. For built-in silencers, the (E) ports are plugged. For the wiring to power supply terminal, refer to page 0.

41 How to Order Solenoid Valves Standard SJ 60 C U C6 With switch SJ wiring Note) [For plug-in mixed mounting] Note ) Refer to pages 6 and 6 for the dedicated non plug-in individual wiring. A B C Type of actuation position single solenoid position double solenoid position closed center position exhaust center position pressure center ual port valve: N.C./N.C. ual port valve: N.O./N.O. ual port valve: N.C./N.O. Refer to page 6 through to for the Symbol. Nil T SJ Series SJ000 SJ000 Nil R Coil spec. Standard With power saving circuit (Continuous duty type) Be sure to select with power saving circuit when the solenoid valve will be energized continuously for long period. Connector entry C: edicated for centralized wiring M: wiring, With lead wire Length 00 mm MN: wiring, Without lead wire (With connector, socket) MO: wiring, Without connector With linkage printed circuit board With linkage printed circuit board With linkage printed circuit board Connector Type PC System with Power Supply Terminal 60 C Z J C6 60 M Z C6 Pilot spec. Internal pilot External pilot External pilot spec. is not applicable for position dual port valves. With switch Connector entries with the symbol M can not use the switch signal from the common wiring on the manifold. For details, refer to Connector iagram on page. When ordering a connector assembly separately, refer to pages 0 and 0. Back pressure check valve Nil None K Built-in Back pressure check valve is not applicable for position valve. Rated voltage VC Light/surge voltage suppressor With light/surge voltage suppressor U (Non-polar type) With light/surge voltage suppressor Z (Polar type) When the types with power saving circuit, with switches, and/or individual wiring are used, the non-polar type cannot be selected. Z is positive common spec. Manual override Nil: Non-locking push type : Push-turn locking slotted type F: Slide locking type Series SJ000/000 Single solenoid Nil A, B port size Straight (Metric size) C: ø C: ø C6: ø6 (SJ000 only) (Inch size) N: ø/" N: ø/" N7: ø/" (SJ000 only) M: M x 0. (SJ000 only) M: M x 0. (SJ000 only) wiring spec. Single wiring ouble wiring There is no need to enter anything for position double, position and position solenoid valves. Select this when the unused numbers to wiring are set. Refer to page for details. Elbow fitting assembly (Upward entry) (Metric size) L: ø elbow fitting assembly L: ø elbow fitting assembly L6: ø6 elbow fitting assembly (SJ000 only) (Inch size) LN: ø/" elbow fitting assembly LN: ø/" elbow fitting assembly LN7: ø/" elbow fitting assembly (SJ000 only) Elbow fitting assembly (ownward entry) (Metric size) B: ø elbow fitting assembly B: ø elbow fitting assembly B6: ø6 elbow fitting assembly (SJ000 only) (Inch size) BN: ø/" elbow fitting assembly BN: ø/" elbow fitting assembly BN7: ø/" elbow fitting assembly (SJ000 only) Note ) The electrical connection to the manifold will be positive common spec. when light/surge voltage suppressor is Z (Polar type). Protective class class # (Mark: ) SJ Specifications Manifold Options Made to Order SJA6 Specifications/

42 Series SJ000/000 Manifold Electrical Type 60G: Flat ribbon cable (0 pins, PC wiring with power supply terminal) Station Station Station Station Station Station 6 Station 7 Station Terminal no Triangle mark, VC - +, Power supply terminal Note ) This circuits are for the specifications with up to stations of position double, position and position dual port valves. These should be wired in order 0 6 without skipping or leaving any connectors remaining. Note ) For details on PC wiring systems, refer to PC System catalog (CAT.ES0-0).

43 Connector Type PC System with Power Supply Terminal Series SJ000/000 SJ imensions SSJ-60G- Stations U(S, R, RS).6. (Pitch) P = 7. M x 0. [(A), (B) port] [External pilot spec.] Specifications [(P), (E) port] Applicable tubing O.: ø, ø/6" (7.) (9.). [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" Valve lock switch + - VC +COM.6 (L) side (.) (.6) Power supply terminal Manual override switch PCW type (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" 9. (6.) 0 (7) PE Manifold Options IN rail Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw Light/surge voltage suppressor : Orange : Green 0 Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L (Station n) (Station ). Slide locking type ( manual override??? ) ON OFF ON OFF (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) Applicable connector: 0 pin MIL type with strain relief (MIL-C-0 compliant) Triangle mark location X Made to Order SJA6 Specifications/ Height to manual override Push type manual override: 0. Locking type manual override: 0. L: imensions n: Stations L n L L L Switch (When equipped with switch) Note) For manifold dimensions including elbow fitting, refer to page. 6

44 Series SJ000/000 imensions SSJ-60G- Stations B (S, R, RS).6 (Pitch) P = [External pilot spec.] (There is a piping of X, PE port in the both sides.) [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" M x 0. [(A), (B) port] (Station n) (Station ) Light/surge voltage suppressor : Orange : Green (L) Power supply terminal Valve lock switch + - (.) (.6) 0. VC +COM (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" side (7.) (9.)..6 PCW type (6.) 9. (7) 0 PE X IN rail Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow Manual override switch L (IN rail mounting hole pitch:.) L. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) Applicable connector: 0 pin MIL type with strain relief (MIL-C-0 compliant) Triangle mark location. Slide locking type ( manual override ) 0 OFF OFF ON ON 7. Height to manual override Push type manual override: 0. Locking type manual override: 0. Switch (When equipped with switch) L: imensions n: Stations L n L L L Note) For manifold dimensions including elbow fitting, refer to page.

45 Connector Type PC System with Power Supply Terminal Series SJ000/000 SJ imensions SSJ-60G- Stations U(S, R, RS) Specifications.6. (Pitch) P = 0 M x 0. [(A), (B) port] [External pilot spec.] [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" C6:. ( N7: 0.6 ) (9.). Power supply terminal Valve lock switch + - VC +COM.6 side (L) (.) 7. C6: 9.6 ( N7:. ) (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" PCW type 0. (X: External pilot port) Applicable tubing O.: ø, ø/" 9. (6.) 0 (7) PE 6. Manifold Options IN rail Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw Light/surge voltage suppressor : Orange : Green 0 Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow (Station n) (Station ) ON OFF Manual override switch L (IN rail mounting hole pitch:.) L. Slide locking type ( manual override ) ON OFF. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) Applicable connector: 0 pin MIL type with strain relief (MIL-C-0 compliant) Triangle mark location X Made to Order SJA6 Specifications/ Height to manual override Push type manual override: 0. Locking type manual override: 0. L: imensions n: Stations L n L L L Switch (When equipped with switch) Note) For manifold dimensions including elbow fitting, refer to page.

46 Series SJ000/000 imensions SSJ-60G- Stations.6 B(S, R, RS) (Pitch) P = [External pilot spec.] (There is a piping of X, PE port in the both sides.) [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" M 0. [(A), (B) port] (Station n) (Station ) Light/surge voltage suppressor : Orange : Green Power supply terminal side (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" 0. (X: External pilot port) Applicable tubing O.: ø, ø/" 6. C6:. ( N7: 0.6 ) (9.). Valve lock switch + - VC +COM.6 (L) 7. (.) C6: 9.6 ( N7:. ) PCW type 9. (6.) 0 (7) PE X IN rail Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow Manual override switch L (IN rail mounting hole pitch:.) L. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) Applicable connector: 0 pin MIL type with strain relief (MIL-C-0 compliant) Triangle mark location. Slide locking type ( manual override ) 0 ON OFF ON OFF 7. Height to manual override Push type manual override: 0. Locking type manual override: 0. Switch (When equipped with switch) Note) For manifold dimensions including elbow fitting, refer to page. L: imensions n: Stations L n L L L

47 Connector Type PC System with Power Supply Terminal Series SJ000/000 SJ imensions SSJ-M60G- Switch for locking a connector (9.) Stations.6 [(P), (E) port] Applicable tubing O.: ø, ø/6". [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" SJ000 pitch P = 0 U(S, R, RS) Power supply terminal SJ000 pitch P = VC +COM.6 (L). (SJ000) [ (SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" side. (SJ000) [. (SJ000)] 7. (SJ000) [7. (SJ000)] (9.6) (SJ000) [(7.) (SJ000)] L dimension: Formula, L to L = 7. x n + 0 x n M = ( + )/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/- PCW type n: Quantity of SJ000 n: Quantity of SJ000 The dimensions of L to L for SSJ-M60G- Stations are the same as those of SSJ-M60G- Stations U. Specifications IN rail IN rail holding screw SSJ-M60G-.6 [(P), (E) port] Applicable tubing O.: ø, ø/6" (9.). Manual override (Non-lock) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) Stations SJ000 pitch P = 0 L [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" B(S, R, RS) SJ000 pitch P = 7. Power supply terminal + - VC +COM.6 Applicable connector: 0 pin MIL type with strain relief (MIL-C-0 compliant). (SJ000) [ (SJ000)]. (SJ000) [. (SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" (L) side 7. (SJ000) [7. (SJ000)] (9.6) (SJ000) [(7.) (SJ000)] 0. Triangle mark location L dimension: Formula, L to L = 7. x n + 0 x n M = ( + )/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/- n: Quantity of SJ000 n: Quantity of SJ000 Manifold Options Made to Order SJA6 Specifications/ IN rail IN rail holding screw Manual override (Non-lock) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L 6. Applicable connector: 0 pin MIL type with strain relief (MIL-C-0 compliant) PCW type Triangle mark location 0

48 Connector Type Type 60S EX0 Integrated Type (for Output) Serial Transmission System Series SJ000/000 Nil M SSJ Series SJ000 SJ000 (SJ000/000 mixed) Mixed mounting type Standard Note ) Mixed mounting Note ) Note ) There is no need to enter anything when you operate either the SJ000 or SJ000 series alone. Note ) Enter M when the SJ000 or SJ000 series will be mounted on the same manifold base together. 0 V Q Q Component module Without SI unit CC-Link compliant ( points) evicenet compliant ( points) evicenet compliant (6 points) Please contact SMC for a specification of the SI unit. Nil A Symbol 0 How to Order Manifold Assembly 60 S V Communication connector spec. T-branch type Straight type Stations station stations Ordering example (SSJ-60SV - ) ouble solenoid, individual wiring/lead wire length 00 mm ( VC) SJ60-MZ-C6 ( set) ouble solenoid, with switch ( VC) SJ60-CZJ-C6 ( set) ouble solenoid ( VC) SJ60-CU-C6 ( sets) Stations side SSJ-60SV set (Manifold part no.) SJ60-CU-C6... sets (Single solenoid part no.) SJ60-CU-C6... sets (ouble solenoid part no.) SJ60-CZJ-C6... set (ouble solenoid, with switch part no.) SJ60-MZ-C6... set (ouble solenoid, individual wiring/lead wire length 00 mm part no.) The asterisk denotes the symbol for assembly. Prefix to the part no. of the solenoid valve, etc. The valve arrangement is numbered as the st station from side. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. In the case of complex arrangement, specify them in the manifold specification sheet. Note) When ordering a manifold, specify the part nos. of valves to be mounted together. (An order cannot be placed with only the manifold part no.) How to Order Communication connector, power connector are shipped together with manifold. Power connector is available of straight type only. SI unit common spec. Nil Positive common N Negative common Unit mounting position side Valve stations Note Up to solenoids possible. The number of the blanking block assembly is also included. Since single and double wiring are available with the blanking block assembly, select a model compatible with the valve wiring spec. planned for the future. (Refer to page 70.) Single solenoid ( VC) SJ60-CU-C6 ( sets) SUP/EXH block ( side mounting) U SUP/EXH block mounting position U ( to 0 stations) side ( to 0 stations) B Both sides ( to stations) M Special specifications Specify the required specifications (including port sizes other than ø) by means of the manifold specification sheet. SI Unit Part No. Symbol V VN VA VAN Q QN QA QAN Q QN QA QAN Power source for driving valve 0 An order cannot be placed with only the manifold part no. Be sure to order solenoid valves for mounting at the same time while referring to the ordering example. Component module/communication connector specifications CC-LINK compliant ( points), T-branch type CC-LINK compliant ( points), Straight type evicenet compliant ( points), T-branch type evicenet compliant ( points), Straight type evicenet compliant (6 points), T-branch type evicenet compliant (6 points), Straight type SUP/EXH block fitting spec. Straight fitting Nil L B IN rail length specified Nil Standard length stations stations Specify a longer rail than the standard length. Elbow fitting (Upward) Elbow fitting (ownward) There is no need to enter anything when the SUP/EXH block mounting position M is selected. Pilot spec. Nil S R RS Internal pilot Internal pilot/built-in silencer External pilot External pilot/built-in silencer There is no need to enter anything when the SUP/EXH block mounting position M is selected. For built-in silencers, the (E) ports are plugged. spec. SI unit part no. NPN output (Positive common) EX0-SMJ PNP output (Negative common) EX0-SMJ NPN output (Positive common) EX0-SMJA PNP output (Negative common) EX0-SMJA NPN output (Positive common) EX0-SN PNP output (Negative common) EX0-SN NPN output (Positive common) EX0-SNA PNP output (Negative common) EX0-SNA NPN output (Positive common) EX0-SN PNP output (Negative common) EX0-SN6 NPN output (Positive common) EX0-SNA PNP output (Negative common) EX0-SN6A Item Specifications Non-polar VC + 0%/ % With energy saving circuit (Continuous duty) VC + 0%/0% Specify the valve stations not exceeding the maximum stations. Refer to Reduced Fieldbus System (Serial Transmission) in Electric Products (CAT.E0) and the Operation Manual for the details of EX0 integrated-type (for output) serial transmission system. Please download it via our website.

49 A B C Type of actuation position single solenoid position double solenoid position closed center position exhaust center position pressure center ual port valve: N.C./N.C. ual port valve: N.O./N.O. ual port valve: N.C./N.O. Refer to pages 6 through to for the Symbol. Nil T Standard With switch wiring Note) [For plug-in mixed mounting] Note ) Refer to pages 6 and 6 for the dedicated non plug-in individual wiring. Coil spec. Standard With power saving circuit (Continuous duty type) Be sure to select with power saving circuit when the solenoid valve will be energized continuously for long period. SJ SJ SJ Nil R Connector entry C: edicated for centralized wiring M: wiring, With lead wire Length 00 mm Connector Type EX0 Integrated Type (for Output) Serial Transmission System Series SJ000 SJ000 How to Order Solenoid Valves Pilot spec. Internal pilot External pilot External pilot spec. is not applicable for position dual port valves. 60 C U C6 60 C Z J C6 60 M Z C6 Back pressure check valve Nil None K Built-in Back pressure check valve is not applicable for position solenoid valve. With switch Rated voltage VC specifications Nil Positive common N Negative common For the non-polar type, there is no need to select a symbol. When equipped with the standard type switch, select common specifications suitable for the SI unit common specifications. Light/surge voltage suppressor With light/surge voltage suppressor U (Non-polar type) With light/surge voltage suppressor Z (Polar type) When the types with power saving circuit, with switches, and/or individual wiring are used, the non-polar type cannot be selected. Manual override Nil: Non-locking push type Series SJ000/000 Single solenoid wiring spec. Nil Single wiring ouble wiring There is no need to enter anything for position double, position and position solenoid valves. Select this when the unused numbers to wiring are set. Refer to page for details. A, B port size Straight (Metric size) C: ø C: ø C6: ø6 (SJ000 only) (Inch size) N: ø/" N: ø/" N7: ø/" (SJ000 only) M: M x 0. (SJ000 only) M: M x 0. (SJ000 only) Elbow fitting assembly (Upward entry) (Metric size) L: ø elbow fitting assembly L: ø elbow fitting assembly L6: ø6 elbow fitting assembly (SJ000 only) (Inch size) LN: ø/" elbow fitting assembly LN: ø/" elbow fitting assembly LN7: ø/" elbow fitting assembly (SJ000 only) SJ Specifications Manifold Options Made to Order SJA6 Specifications/ MN: wiring, Without lead wire (With connector, socket) MO: wiring, Without connector With linkage printed circuit board With linkage printed circuit board With linkage printed circuit board Connector entries with the symbol M can not use the switch signal from the common wiring on the manifold. For details, refer to Connector iagram on page. When ordering a connector assembly separately, refer to pages 0 and 0. : Push-turn locking slotted type F: Slide locking type Elbow fitting assembly (ownward entry) (Metric size) B: ø elbow fitting assembly B: ø elbow fitting assembly B6: ø6 elbow fitting assembly (SJ000 only) (Inch size) BN: ø/" elbow fitting assembly BN: ø/" elbow fitting assembly BN7: ø/" elbow fitting assembly (SJ000 only) Note ) The electrical connection to the manifold will be positive common spec. when light/surge voltage suppressor is Z (Polar type). Protective class class # (Mark: )

50 Series SJ000/000 imensions: Series SJ000 for EX0 Integrated Type (for Output) Serial Transmission System SSJ-60S - Stations U(S, R, RS).6. (Pitch) P = 7. Power source connector (shipped together with manifold) Ground terminal M [External pilot spec.].6 [(P), (E) port] Applicable tubing O.: ø, ø/6" (9.) [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" Valve lock switch M x 0. [(A), (B) port]. (.) Straight type: (.6) Communication connector (shipped together with manifold) side (L) (.) (.6).. 6. (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" 0. (X: External pilot port) Applicable tubing O.: ø, ø/" 6. (7.) (7.) Straight type: (.9) 9. (6.) 0 (7) PE X IN rail Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw locations (M) Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L SI unit Manual override switch. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) IN rail holding screw locations (M) (Station n) (Station ) Light/surge voltage suppressor : Orange : Green. Slide locking type ( manual override ) 0 OFF OFF ON ON 7. Height to manual override Push type manual override: 0. Locking type manual override: 0. Switch (When equipped with switch) Note) Refer to page for the dimensions of the manifold with elbow fittings and pages 6 to 660 of Best Pneumatics No. for the details of SI unit. L: imensions n: Stations L n L L L

51 Connector Type EX0 Integrated Type (for Output) Serial Transmission System imensions: Series SJ000 for EX0 Integrated Type (for Output) Serial Transmission System SSJ-60S - Stations B(S, R, RS).6 (Pitch) P = Power source connector (shipped together with manifold) Ground terminal M Series SJ000/000 [External pilot spec.] (There is a piping of X, PE port in the both sides.) SJ Specifications.6 [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" (7.). IN rail Valve lock switch M x 0. [(A), (B) port]. (.) Straight type: (.6) Communication connector (shipped together with manifold) (L) side 7. (9.) (7.) Straight type: (.9). 9.. (6.) 6. (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" 0 (7) 0. (X: External pilot port) Applicable tubing O.: ø, ø/" PE X 6. Manifold Options Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw locations (M) Light/surge voltage suppressor : Orange : Green Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L (Station n) (Station ). Slide locking type ( manual override ) SI unit. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) IN rail holding screw locations (M) Manual override switch Made to Order SJA6 Specifications/ 0 OFF OFF ON ON 7. Height to manual override Push type manual override: 0. Locking type manual override: 0. L: imensions n: Stations L n L L L n L L L L Switch (When equipped with switch) Note) Refer to page for the dimensions of the manifold with elbow fittings and pages 6 to 660 of Best Pneumatics No. for the details of SI unit.

52 Series SJ000/000 imensions: Series SJ000 for EX0 Integrated Type (for Output) Serial Transmission System SSJ-60S - Stations U (S, R, RS) Power source connector (shipped together with manifold).6. (Pitch) P = 0 Ground terminal M [External pilot spec.] C6:. ( N7: 0.6 ).6 [(P), (E) port] Applicable tubing O.: ø, ø/6" (9.). [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" Valve lock switch M x 0. [(A), (B) port].. (.) Straight type: (.6) Communication connector (shipped together with manifold) (L) side (.) C6: 9.6 ( N7:. ) (7.) Straight type: (.9). 9.. (6.) 6. (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" 0 (7) PE 6. X IN rail IN rail holding screw locations (M) Silencer (Air discharge port) (Built-in silencer spec.) Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L (Station n) (Station ) SI unit. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) IN rail holding screw locations (M) Manual override switch Light/surge voltage suppressor : Orange : Green. Slide locking type ( manual override ) 0 OFF ON OFF ON 7. Height to manual override Push type manual override: 0. Locking type manual override: 0. Switch (When equipped with switch) Note) Refer to page for the dimensions of the manifold with elbow fittings and pages 6 to 660 of Best Pneumatics No. for the details of SI unit. L: imensions n: Stations L n L L L

53 Connector Type EX0 Integrated Type (for Output) Serial Transmission System imensions: Series SJ000 for EX0 Integrated Type (for Output) Serial Transmission System SSJ-60S - Stations B(S, R, RS).6 (Pitch) P = Power source connector (shipped together with manifold) Ground terminal M Series SJ000/000 [External pilot spec.] SJ Specifications.6 [(P), (E) port] Applicable tubing O.: ø, ø/6" C6:. ( N7: 0.6 ). IN rail [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" Silencer (Air discharge port) (Built-in silencer spec.) Light/surge voltage suppressor : Orange : Green Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow M 0. [(A), (B) port] IN rail holding screw locations (M) L (IN rail mounting hole pitch:.) L (Station n) (Station ). Valve lock switch Slide locking type ( manual override ) SI unit.. (.) Straight type: (.6) Communication connector (shipped together with manifold) (L) side. 7. (When equipped with switch) (9.) (For individual wiring) (7.) Straight type: (.9) Approx. 00 (Lead wire length) IN rail holding screw locations (M) Manual override switch. 9.. (6.) 6. (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" 0 (7) PE X Manifold Options Made to Order SJA6 Specifications/ 0 OFF ON OFF ON 7. Height to manual override Push type manual override: 0. Locking type manual override: 0. L: imensions n: Stations L n L L L n L L L L Switch (When equipped with switch) Note) Refer to page for the dimensions of the manifold with elbow fittings and pages 6 to 660 of Best Pneumatics No. for the details of SI unit. 6

54 Series SJ000/000 imensions: SJ000/000 Mixed Manifold SSJ-M60S - Stations U (S, R, RS).6 [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" (M) (9.) (9.)..6. IN rail IN rail holding screw locations SJ000 pitch P = 0 Manual override (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L 0 x n 0 (SJ000) [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" SJ000 pitch P = 7. SSJ-M60S - Stations B (S, R, RS) [(P), (E) port] Applicable tubing O.: ø, ø/6" SJ000 pitch P = 0 7. x n 7. (SJ000) L 7. (SJ000) [7. (SJ000)]. (SJ000) [ (SJ000)] (9.6) (SJ000) (SJ000) [(SJ000)]. (SJ000) [. (SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" SJ000 pitch P = 7. side [(7.) (SJ000)] IN rail holding screw locations (M) SI unit 7. (SJ000) [7. (SJ000)].(SJ000) [.(SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" side L (9.6) (SJ000) [(7.) (SJ000)] L dimension: Formula, L to L = 7. x n + 0 x n +. M = ( + )/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ n: Quantity of SJ000 n: Quantity of SJ000 The dimensions of L to L for SSJ-M60S - Stations are the same as those of SSJ-M60S - Stations U. L dimension: Formula, L to L = 7. x n + 0 x n M = ( + )/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ n: Quantity of SJ000 n: Quantity of SJ000 IN rail IN rail holding screw locations (M) Manual override (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L IN rail holding screw locations (M) SI unit

55 Connector Type Type 60S6B EX0 Gateway System Serial Transmission System Series SJ000/000 SSJ How to Order Manifold 60S6B 0 An order cannot be placed with only the manifold part no. Be sure to order solenoid valves for mounting at the same time while referring to the ordering example. Nil M Manifold series SJ000 SJ000 (SJ000/000 mixed) Standard Note ) Mixed mounting Note ) Note ) There is no need to enter anything when you operate either the SJ000 or SJ000 series alone. Note ) Enter M when the SJ000 or SJ000 series will be mounted on the same manifold base together. Symbol SI unit common spec. Nil Positive common N Negative common Unit mounting position side No. of stations How to Order Valve Manifold Assembly Valve stations Note 0 station Up to 6 solenoids possible.6 6 stations The number of the blanking block assembly is also included. Since single and double wiring are available with the blanking block assembly, select a model compatible with the valve wiring spec. planned for the future. Mixed mounting type IN rail length specified Nil Standard length 6 stations 6 stations Specify a longer rail than the standard length. Specify the valve stations not exceeding the maximum stations. SUP/EXH block fitting spec. Straight fitting Nil With external pilot spec. X, PE port Elbow fitting (Upward) L With external pilot spec. X, PE port Elbow fitting (ownward) B With external pilot spec. X, PE port There is no need to enter anything when the SUP/EXH block mounting position M is selected. 9 Ordering example (SSJ-60S6B- ) Stations side SSJ-60S6B-0U... set (Type 60S6B, -station manifold base part no.) SJ60-CU-C6... sets (Single solenoid part no.) SJ60-CU-C6... sets (ouble solenoid part no.) The asterisk denotes the symbol for assembly. Prefix to the part no. of the solenoid valve, etc. SUP/EXH block ( mounting) ouble solenoid ( VC) SJ60-CU-C6 ( sets) Single solenoid ( VC) SJ60-CU-C6 ( sets) Manifold base ( stations) SSJ-60S6B-0U The valve arrangement is numbered as the st station from side. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. In the case of complex arrangement, specify them in the manifold specification sheet. Note) When ordering a manifold, specify the part nos. of valves to be mounted together. (An order cannot be placed with only the manifold part no.) SI Unit Part No. Symbol SI unit specifications Nil NPN output (Positive common) N PNP output (Negative common) Pilot spec. Nil Internal pilot S Internal pilot/built-in silencer R External pilot RS External pilot/built-in silencer There is no need to enter anything when the SUP/EXH block mounting position M is selected. For built-in silencers, the (E) ports are plugged. SUP/EXH block mounting position U ( to 0 stations) side ( to 0 stations) B Both sides ( to 6 stations) M Special specifications Specify the required specifications (including port sizes other than ø) by means of the manifold specification sheet. SI unit part no. EX0-S00C EX0-S0C Page P.7 to 77, Best Pneumatics No. Refer to Reduced Fieldbus System (Serial Transmission) in Electric Products (CAT.E0) and the Operation Manual for the details of EX0 gateway system serial transmission system. Please download it via our website.

56 Standard SJ 60 C U C6 With switch SJ wiring Note) [For plug-in mixed mounting] Note) Refer to pages 6 and 6 for the dedicated non plug-in individual wiring. Type of actuation position single solenoid position double solenoid position closed center position exhaust center position pressure center A ual port valve: N.C./N.C. B ual port valve: N.O./N.O. C ual port valve: N.C./N.O. Refer to pages 6 through to for the Symbol. Coil spec. Nil Standard With power saving circuit T (Continuous duty type) Be sure to select with power saving circuit when the solenoid valve will be energized continuously for long period. SJ Series SJ000 SJ000 Nil R Connector entry C: edicated for centralized wiring M: wiring, With lead wire Length 00 mm MN: wiring, Without lead wire MO: wiring, Without connector Connector Type EX0 Gateway System Serial Transmission System Pilot spec. Internal pilot External pilot External pilot spec. is not applicable for position solenoid dual port valves. With linkage printed circuit board With linkage printed circuit board With linkage printed circuit board How to Order Solenoid Valves 60 C Z J C6 60 M Z C6 Back pressure check valve Nil None K Built-in Back pressure check valve is not applicable for position solenoid valve. With switch Connector entries with the symbol M can not use the switch signal from the common wiring on the manifold. For details, refer to Connector iagram on page. When ordering a connector assembly separately, refer to pages 0 and 0. Rated voltage VC specifications Nil Positive common N Negative common For the non-polar type, there is no need to select a symbol. When equipped with the standard type switch, select common specifications suitable for the SI unit common specifications. Light/surge voltage suppressor With light/surge voltage suppressor U (Non-polar type) With light/surge voltage suppressor Z (Polar type) When the types with power saving circuit, with switches, and individual wiring are used, the non-polar type cannot be selected. Manual override Nil: Non-locking push type : Push-turn locking slotted type F: Slide locking type Series SJ000/000 Single solenoid wiring spec. Nil Single wiring ouble wiring There is no need to enter anything for position double, position and position solenoid valves. Select this when the unused numbers to wiring are set. Refer to page for details. A, B port size Straight (Metric size) C: ø C: ø C6: ø6 (SJ000 only) (Inch size) N: ø/" N: ø/" N7: ø/" (SJ000 only) M: M x 0. (SJ000 only) M: M x 0. (SJ000 only) Elbow fitting assembly (Upward entry) (Metric size) L: ø elbow fitting assembly L: ø elbow fitting assembly L6: ø6 elbow fitting assembly (SJ000 only) (Inch size) LN: ø/" elbow fitting assembly LN: ø/" elbow fitting assembly LN7: ø/" elbow fitting assembly (SJ000 only) Elbow fitting assembly (ownward entry) (Metric size) B: ø elbow fitting assembly B: ø elbow fitting assembly B6: ø6 elbow fitting assembly (SJ000 only) (Inch size) BN: ø/" elbow fitting assembly BN: ø/" elbow fitting assembly BN7: ø/" elbow fitting assembly (SJ000 only) Protective class class # (Mark: ) 0 SJ Specifications Manifold Options Made to Order SJA6 Specifications/

57 Series SJ000/000 imensions: Series SJ000 for EX0 Gateway System Serial Transmission System SSJ-60S6B - Stations U-.6. (Pitch) P = 7. M x 0. [(A), (B) port] (7.) (9.).6 [(P), (E) port] Applicable tubing O.: ø, ø/6". IN rail IN rail holding screw (Light/surge voltage suppressor) : Orange : Green Valve lock switch OFF ON OFF ON (.) Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow FREE LOCK L (.6) L (IN rail mounting hole pitch:.) (Station n) (Station ). [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" Switch for locking a connector Slide locking type ( manual override ) SI unit Manual override switch Switch (When equipped with switch) L side 70 (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) PWR COM Height to manual override Push type manual override: 0. Locking type manual override: 0. L: imensions L n L L L Note) Refer to page for the external pilot specifications, page for the dimensions of the manifold with elbow fittings, and pages 696 to 7 of Best Pneumatics No. for the details of SI unit n: Stations

58 imensions: Series SJ000 for EX0 Gateway System Serial Transmission System SSJ-60S6B - Stations B- Connector Type EX0 Gateway System Serial Transmission System.6 (Pitch) P = 7... Series SJ000/000 SJ Specifications.6. [(P), (E) port] Applicable tubing O.: ø, ø/6" (7.) (9.). IN rail [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" Valve lock switch M x 0. [(A), (B) port] Switch for locking a connector (.) FREE LOCK (.6) L side SI unit PWR COM Manifold Options IN rail holding screw (Light/surge voltage suppressor) : Orange : Green Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L (Station n) (Station ). Slide locking type ( manual override ) Manual override switch. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) Made to Order SJA6 Specifications/ 0 Height to manual override Push type manual override: 0. Locking type manual override: 0. L: imensions L n L L L OFF ON OFF ON Switch (When equipped with switch) Note) Refer to page for the external pilot specifications, page for the dimensions of the manifold with elbow fittings, and pages 696 to 7 of Best Pneumatics No. for the details of SI unit n: Stations

59 imensions: Series SJ000 for EX0 Gateway System Serial Transmission System.6. (Pitch) P = 0 M x 0. [(A), (B) port].6.. [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" L Valve lock switch Switch for locking a connector (9.) (.) SI unit 6. LOCK FREE L (IN rail mounting hole pitch:.) L. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) (Station n) (Station ) OFF ON OFF ON Series SJ000/000 SSJ-60S6B - Stations U- side C6:. ( N7: 0.6 ) C6: 9.6 ( N7:. ) PWR COM IN rail IN rail holding screw Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow Manual override switch (Light/surge voltage suppressor) : Orange : Green. Slide locking type ( manual override ) 0 Height to manual override Push type manual override: 0. Locking type manual override: 0. Switch (When equipped with switch) Note) Refer to page for the external pilot specifications, page for the dimensions of the manifold with elbow fittings, and pages 696 to 7 of Best Pneumatics No. for the details of SI unit. L: imensions L n L L L n: Stations

60 imensions: Series SJ000 for EX0 Gateway System Serial Transmission System.6 (Pitch) P = [(P), (E) port] Applicable tubing O.: ø, ø/6" 0. (9.). [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" M 0. [(A), (B) port] Valve lock switch Switch for locking a connector (.) SI unit L 6. LOCK FREE SSJ-60S6B - Stations B- Connector Type EX0 Gateway System Serial Transmission System Series SJ000/000 SJ Specifications C6:. ( N7: 0.6 ) C6: 9.6 ( N7:. ) side PWR COM Manifold Options IN rail Made to Order IN rail holding screw Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L (Station n) (Station ) Manual override switch. (When equipped with switch) 9.9 (For individual wiring) Approx. 00 (Lead wire length) SJA6 Specifications/ (Light/surge voltage suppressor) : Orange : Green. Slide locking type ( manual override ) 0 Height to manual override Push type manual override: 0. Locking type manual override: 0. L: imensions L n L L L OFF ON OFF ON Switch (When equipped with switch) Note) Refer to page 6 for the external pilot specifications, page for the dimensions of the manifold with elbow fittings, and pages 696 to 7 of Best Pneumatics No. for the details of SI unit n: Stations

61 imensions: SJ000/000 Mixed Manifold for EX0 Gateway System Serial Transmission System (9.).6 [(P), (E) port] Applicable tubing O.: ø, ø/6". SJ000 pitch P=0 [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" SJ000 pitch P=7. side L Switch for locking a connector SI unit. (SJ000) [ (SJ000)]. (SJ000) [. (SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" L dimension: Formula, L to L = 7. x n + 0 x n + 0. M = ( + )/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ n: Quantity of SJ000 n: Quantity of SJ000 The dimensions of L to L for SSJ-M60S6B - Stations are the same as those of SSJ-M60S6B - Stations U. LOCK FREE PWR COM Series SJ000/000 SSJ-M60S6B - Stations U- (9.6)(SJ000) [(7.)(SJ000)] IN rail IN rail holding screw Manual override (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L 7. (SJ000) [7. (SJ000)] SSJ-M60S6B - Stations B- (9.)..6 [(P), (E) port] Applicable tubing O.: ø, ø/6" IN rail SJ000 pitch P = 0 SJ000 pitch P = 7. [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/". (SJ000) [ (SJ000)]. (SJ000) [. (SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" side L Switch for locking a connector FREE LOCK SI unit (9.6) (SJ000) [(7.) (SJ000)] PWR COM L dimension: Formula, L to L = 7. x n + 0 x n M = ( + )/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ n: Quantity of SJ000 n: Quantity of SJ000 IN rail holding screw Manual override (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L 7. (SJ000) [7. (SJ000)]

62 Connector Type Type 60P (Flat ribbon cable) manifold Series SJ000/000 Manifold Exploded View Valve lock switch Manual override switch Type 60S (, EX0 Integrated type (for output) serial transmission system) manifold SI unit Fixed switch ( locations) e t Type 60G (, PC wiring with power supply terminal) manifold e y SJ Specifications w q SUP block disk assembly EXH block disk assembly e r Component Parts/ (Connector Type) No. escription Internal pilot Internal pilot/built-in silencer 6 SUP/EXH block assembly External pilot External pilot/built-in silencer For different pressures, internal pilot Note ) For different pressures, internal pilot/built-in silencer Note ) End block assembly Connector block assembly IN rail SI unit End block assembly Part no. SJ000-0-A- SJ000-0-AS- SJ000-0-AR- X, PE port: Metric size ø Inch size ø/" SJ000-0-ARS- X port: Metric size ø X port: Inch size ø/" SJ000-0-A- SJ000-0-AS- SJ000--A SJ000-- A- SJ A-0 VZ EX0- SJ000--A side Note (Metric size) C6: With ø6 (straight) C: With ø (straight) L6: With ø6 (elbow upward entry) L: With ø (elbow upward entry) B6: With ø6 (elbow downward entry) B: With ø (elbow downward entry) (Inch size) N7: With /" (straight) N9: With /6" (straight) For Refer to the connector block assembly part no. shown below. Refer to page 7. Refer to the SI unit part numbers on page. For side Note ) The valves cannot be operated only with the SUP/EXH block assembly for different pressure, select them in combination with the SUP/EXH block assembly for internal/ external pilot. Note ) Refer to page 69 about the SUP/EXH block disk assembly and method of handling of parts at different pressures. Manifold Options Made to Order SJA6 Specifications/ Connector Block Assembly Part No. Connector specifications Mounting position Part no. For -sub connector (Locking bracket: Metric size thread) For -sub connector (Locking bracket: Unified thread) For flat ribbon cable 6 pins For flat ribbon cable 0 pins For flat ribbon cable 0 pins For PC wiring 0 pins For EX0 serial wiring Note) For EX0 serial wiring Note) For PC wiring 0 pins with power supply terminal Note) SI unit is not included. Connector Block Assembly with SI Unit Connector block assembly with EX0 serial wiring side side SJ000--0A- SJ000--A- SJ000--AU- SJ000--A- SJ000--A- SJ000--A- SJ000--6A- SJ000--0A SJ000--A- SJ A-0 Note : (Connector upward) : (Connector lateral) For details on portion, refer to the SI unit part no. on page. Example: SJ000--0A-V (CC-LINK compliant, T-branch type) 6

63 Type 60LP (Flat ribbon cable) manifold Series SJ000/000 Manifold Exploded View Valve lock switch Valve lock switch Manual override switch Blanking block w e q r Cable Component Parts/ () No. escription Internal pilot Internal pilot/built-in silencer SUP/EXH block assembly External pilot External pilot/built-in silencer For different pressures, internal pilot Note ) For different pressures, internal pilot/built-in silencer Note ) End block assembly Connector block assembly IN rail Part no. SJ000-0-A- SJ000-0-AS- SJ000-0-AR- X, PE port: Metric size ø Inch size ø/" SJ000-0-ARS- X port: Metric size ø Inch size ø/" SJ A- SJ AS- SJ000--A SJ000-- A- VZ Note (Metric size) C6: With ø6 (straight) C: With ø (straight) L6: With ø6 (elbow upward entry) L: With ø (elbow upward entry) B6: With ø6 (elbow downward entry) B: With ø (elbow downward entry) (Inch size) N7: With /" (straight) N9: With /6" (straight) For Refer to the connector block assembly part no. shown below. Refer to page 7. Note ) The valves cannot be operated only with the SUP/EXH block assembly for different pressure, select them in combination with the SUP/EXH block assembly for internal/ external pilot. Note ) Refer to page 69 about the SUP/EXH block disk assembly and method of handling of parts at different pressures. Connector Block Assembly SJ000 A 0 For -sub connector For flat ribbon cable 6 pins For flat ribbon cable 0 pins For flat ribbon cable 0 pins For -sub connector For flat ribbon cable 6 pins For flat ribbon cable 0 pins For flat ribbon cable 0 pins Connector type Series SJ000 Series SJ000 All connector block assembly mounting positions become the side. The connector block assembly includes the cables necessary for the number of stations. Locking bracket Nil Metric size thread U Unified thread -sub connector only. Connector entry direction Valve stations 0 to 0 For -sub connector 0 to 0 0 to 0 For flat ribbon cable 6 pins 0 to 0 0 to 09 For flat ribbon cable 0 pins 0 to 0 to 0 For flat ribbon cable 0 pins 0 to 0 Nil All double wiring S All single wiring Upward Lateral side All double wiring All single wiring All double wiring All single wiring All double wiring All single wiring All double wiring All single wiring

64 Connector Type Series SJ000/000 How to Increase Manifold Stations a Loosen threads a, which are fixed onto the IN rail (two locations on one side). SJ Specifications End block assembly SUP/EXH block assembly Connector block assembly Valve lock switch a a side Valve lock switch [Unlocked] ( FREE appears, which indicates the manual switch is locked.) Serial connector block assembly In the direction of the coil, slide the valve where the station is desired to add and the valve lock switch on each block. If blocks are removed without completely releasing the valve lock switch, the connection hook of that switch could be damaged or deformed. Connecting hook Install an additional valve or an SUP/EXH block assembly block on the IN rail.. Press the manifold in the arrow direction and mount it on the rail. Manifold Options. Hook on the rail. Made to Order Valve lock switch [Locked] ( FREE cannot be seen.) A manifold equipped with a valve or a block assembly can be mounted on the IN rail. However, a serial connector block assembly cannot be mounted on the IN rail when it is connected with another block; the serial connector block must be mounted separately. SJA6 Specifications/ Caution Press the manifold. Caution Press the manifold. Press the valves and block assemblies to each other for connection. Press the valve lock switch in the cylinder port direction until it does not go any further. Fasten threads a onto the IN rail. After fixing the connector block assembly, fasten the threads onto the end block assembly while holding it lightly by hand. This is necessary to improve sealing. -sub, Connector block assembly for flat ribbon cable, End block assembly M: 0. lbf ft (0.6 N m) Connector block assembly for EX0 serial wiring M:.0 lbf ft (. N m) Mounting bracket for EX0 serial wiring M: 0. lbf ft (0.6 N m). When increasing the number of stations from 0 or below to or above, increase the number of SUP/EXH block assemblies as well.. Be sure to turn off the power and stop the supply of air before disassembly. Furthermore, since air may remain inside the actuator, piping and manifold, confirm that the air is completely exhausted before performing any work.. After assembly and disassembly, air leakage could occur if blocks are not well connected or a thread is not tightly fastened onto the end block assembly. Before supplying air, make sure that no gaps exist in between blocks and that the valve and block are tightly fastened onto the IN rail. Also, make sure that air is not leaking before use.. For the SJA6 series manifold with vacuum release valve with restrictor, there is no valve lock switch for connecting, so when mounting, tighten the screws after checking that there are no gaps between valves.

65 Series SJ000/000 How to Increase Manifold Stations a Caution To increase a manifold station, a housing holder (refer to the table below) is required in addition to the solenoid valve. For the manifold with less than the maximum stations, spare housing (for one station) for adding the manifold station is stored in the housing holder of the last station or the SUP/EXH block assembly. To increase a manifold station, follow the steps below to disassemble and reassemble the manifold. Series Housing holder part no. Material Note a End block assembly SUP/EXH block assembly Connector block assembly side SJ000 SJ000 SJ SJ Resin White Loosen threads a, which are fixed onto the IN rail (two locations). [Note: To replace the IN rail, also loosen the screws ( locations) on the connector block assembly.] Slide the valve lock switch on each block toward the coil, and then remove the end block assembly and SUP/EXH block assembly. Housing holder Valve lock switch Valve lock switch [Unlocked] ( FREE appears, which indicates the manual switch is locked.) Take out the stored housing for adding the manifold station and assemble it to a newly added housing holder. Insert this housing holder next to the existing housing holder. How to mount the housing q Station number imprinting Housing Make the number imprinted on the housing w Push this part. matched with the station number. Connecting hook Convex portion for connection Housing holder qmount the housing in the arrow direction. wpush in the housing securely using a flat blade screwdriver. Valve lock switch [Locked] ( FREE cannot be seen.). Make the connectors matched with each other.. Press the manifold in the arrow direction and mount it on the rail.. Hook on the rail. Caution Caution Press the manifold. Last station Station Press the manifold. side Press the valves and block assemblies to each other for connection. Press the valve lock switch in the cylinder port direction until it does not go any further. Fasten threads a onto the IN rail. Connect the added valve and SUP/EXH block, and then fasten the IN rail fixing screws on the end block on the. After fixing the connector block assembly, fasten the threads onto the end block assembly while holding it lightly by hand. This is necessary to improve sealing. -sub, Connector block assembly for flat ribbon cable, End block assembly M: 0. lbf ft (0.6 N m). When increasing the number of stations from 0 or below to or above, increase the number of SUP/EXH block assemblies as well. Add the valve to the of the last station, and then add the SUP/EXH block assembly to its. The SUP/EXH block cannot be added to a position adjacent to the connector block assembly or an intermediate position.. Be sure to turn off the power and stop the supply of air before disassembly. Furthermore, since air may remain inside the actuator, piping and manifold, confirm that the air is completely exhausted before performing any work.. After assembly and disassembly, air leakage could occur if blocks are not well connected or a thread is not tightly fastened onto the end block assembly. Before supplying air, make sure that no gaps exist in between blocks and that the valve and block are tightly fastened onto the IN rail. Also, make sure that air is not leaking before use.. For the SJA6 series manifold with vacuum release valve with restrictor, there is no valve lock switch for connecting, so when mounting, tighten the screws after checking that there are no gaps between valves. 9

66 Non Manifold Series SJ000/000 SJ Specifications P.6 Made to Order Manifold Options SJA6 Specifications/ 60

67 Series SJ000/000 How to Order An order cannot be placed with only the manifold part no. Be sure to order solenoid valves for mounting at the same time while referring to the ordering example. wiring manifold SSJ 60 0 U Series SJ000 SJ000 (SJ000/000 mixed) How to Order Manifold Assembly Ordering example (SSJ-60- ) Stations side Mixed mounting type Nil Standard Note ) M Mixed mounting Note ) Note ) There is no need to enter anything when you operate either the SJ000 or SJ000 series alone. Note ) Enter M when the SJ000 or SJ000 series will be mounted on the same manifold base together. ouble solenoid ( VC) SJ60N-MZ-C6 ( sets) Single solenoid ( VC) SJ60N-MZ-C6 ( sets) SUP/EXH block ( side mounting) Valve stations Symbol Stations 0 station 0 0 stations IN rail length specified Nil Standard length 0 stations 0 stations Specify a longer rail than the standard length. Specify the valve stations not exceeding the maximum stations. SUP/EXH block fitting spec. Straight fitting Nil With external pilot spec. X, PE port Elbow fitting (Upward) L With external pilot spec. X, PE port Elbow fitting (ownward) B With external pilot spec. X, PE port There is no need to enter anything when the SUP/EXH block mounting position M is selected. Pilot spec. Nil Internal pilot S Internal pilot/built-in silencer R External pilot RS External pilot/built-in silencer There is no need to enter anything when the SUP/EXH block mounting position M is selected. For built-in silencers, the (E) ports are plugged. SUP/EXH block mounting position U ( to 0 stations) side ( to 0 stations) B Both sides ( to 0 stations) M Special specifications Specify the required specifications (including port sizes other than ø) by means of the manifold specification sheet. SSJ set (Manifold part no.) SJ60N-MZ-C6... sets (Single solenoid part no.) SJ60N-MZ-C6... sets (ouble solenoid part no.) The asterisk denotes the symbol for assembly. Prefix to the part no. of the solenoid valve, etc. The valve arrangement is numbered as the st station from side. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. In the case of complex arrangement, specify them in the manifold specification sheet. 6

68 A B C Nil R Series SJ000 SJ000 Pilot spec. Internal pilot External pilot External pilot spec. is not applicable for position dual port valves. Back pressure check valve Nil None K Built-in Back pressure check valve is not applicable for position solenoid valve. Rated voltage VC 6 VC How to Order Solenoid Valves SJ 60 N M Z C6 Type of actuation position single solenoid position double solenoid position closed center position exhaust center position pressure center ual port valve: N.C./N.C. ual port valve: N.O./N.O. ual port valve: N.C./N.O. Refer to pages 6 through to for the Symbol. Nil T Coil spec. Standard With power saving circuit (Continuous duty type) Be sure to select with power saving circuit when the solenoid valve will be energized continuously for long period. Non-plug-in specifications Nil Positive common N Negative common With light/surge voltage suppressor Manual override Nil: Non-locking push type Series SJ000/000 A, B port size Straight (Metric size) C: ø C: ø C6: ø6 (SJ000 only) (Inch size) N: ø/" N: ø/" N7: ø/" (SJ000 only) M: M x 0. (SJ000 only) M: M x 0. (SJ000 only) Elbow fitting assembly (Upward entry) (Metric size) L: ø elbow fitting assembly L: ø elbow fitting assembly L6: ø6 elbow fitting assembly (SJ000 only) (Inch size) LN: ø/" elbow fitting assembly LN: ø/" elbow fitting assembly LN7: ø/" elbow fitting assembly (SJ000 only) SJ Specifications Manifold Options Made to Order Connector entry M: wiring, With lead wire Length 00 mm Without linkage printed circuit board MN: wiring, Without lead wire (With connector, socket) Without linkage printed circuit board : Push-turn locking slotted type Elbow fitting assembly (ownward entry) (Metric size) B: ø elbow fitting assembly B: ø elbow fitting assembly B6: ø6 elbow fitting assembly (SJ000 only) (Inch size) BN: ø/" elbow fitting assembly BN: ø/" elbow fitting assembly BN7: ø/" elbow fitting assembly (SJ000 only) SJA6 Specifications/ MO: wiring, Without connector Without linkage printed circuit board When ordering a connector assembly separately, refer to pages 0 and 0. F: Slide locking type Protective class class # (Mark: ) 6

69 Series SJ000/000 imensions SSJ-60- Stations U (S, R, RS).6. (Pitch) P = 7. [External pilot spec.] [(P), (E) port] Applicable tubing O.: ø, ø/6" M x 0. [(A), (B) port] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" (7.) (9.) Manual override switch Valve lock switch (L) side (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" 0. (X: External pilot port) Applicable tubing O.: ø, ø/" (6.) (7) (.) (.6) 0. PE X IN rail Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L 9.9 Approx. 00 (Lead wire length) (Station n) (Station ) Light/surge voltage suppressor : Orange : Green Slide locking type ( manual override ) Height to manual override Push type manual override: 0. Locking type manual override: 0. Note) For manifold dimensions including elbow fitting, refer to page. L: imensions L n L L L n: Stations

70 Series SJ000/000 SJ imensions SSJ-60- Stations B (S, R, RS).6. (Pitch) P = 7. [External pilot spec.] Specifications [(P), (E) port] Applicable tubing O.: ø, ø/6" (7.) (9.). [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" Manual override switch Valve lock switch M x 0. [(A), (B) port] side (L) (.) (.6) (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" 0. (X: External pilot port) Applicable tubing O.: ø, ø/" (6.) 0 0. (7) PE Manifold Options X IN rail Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) (Station n) L (Station ) 9.9 Approx. 00 (Lead wire length) Made to Order SJA6 Specifications/ Light/surge voltage suppressor : Orange : Green. Slide locking type ( manual override ) 0 L: imensions L n L L L Height to manual override Push type manual override: 0. Locking type manual override: Note) For manifold dimensions including elbow fitting, refer to page. n: Stations

71 Series SJ000/000 imensions SSJ-60- Stations U (S, R, RS).6. (Pitch) P = 0 [External pilot spec.] [(P), (E) port] Applicable tubing O.: ø, ø/6" C6:. ( N7: 0.6 ) (9.) [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" Manual override switch Valve lock switch M x 0. [(A), (B) port] side (L) (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" (6.) (7) PE X Approx. 00 (Lead wire length) Light/surge voltage suppressor : Orange : Green (Station n) (Station ) 0 7. (.) C6: 9.6 ( N7:. ) IN rail Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L 9.9. Slide locking type ( manual override ) Height to manual override Push type manual override: 0. Locking type manual override: 0. Note) For manifold dimensions including elbow fitting, refer to page. L: imensions L n L L L n: Stations

72 Series SJ000/000 SJ imensions SSJ-60- Stations B (S, R, RS).6. (Pitch) P = 0 [External pilot spec.] Specifications [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" C6:. ( N7: 0.6 ) (9.). M x 0. [(A), (B) port] (L) (PE: Pilot EXH port) Applicable tubing O.: ø, ø/" (X: External pilot port) Applicable tubing O.: ø, ø/" (6.) 0 Manual override switch Valve lock switch (.) side 7. C6: 9.6 ( N7:. ) 0. (7) IN rail 6. PE X Manifold Options Silencer (Air discharge port) (Built-in silencer spec.) IN rail holding screw Manual override (Locking type: Press, then rotate.) (A) port side: Blue (B) port side: Yellow (Station n) L (IN rail mounting hole pitch:.) L (Station ) 9.9 Approx. 00 (Lead wire length) Made to Order SJA6 Specifications/ Light/surge voltage suppressor : Orange : Green. Slide locking type ( manual override ) 0 L: imensions L n L L L Height to manual override Push type manual override: 0. Locking type manual override: Note) For manifold dimensions including elbow fitting, refer to page. n: Stations

73 Series SJ000/000 imensions: SJ000/000 Mixed Manifold SSJ-M60-.6 [(P), (E) port] Applicable tubing O.: ø, ø/6" (9.) Stations U (S, R, RS) SJ000 pitch P = 0 [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" SJ000 pitch P = 7..(SJ000) [(SJ000)].(SJ000) [.(SJ000)] [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" side (L) (9.6)(SJ000) [(7.)(SJ000)] L dimension: Formula, L to L = 7. x n + 0 x n +. M = ( + )/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ n: Quantity of SJ000 n: Quantity of SJ000 The dimensions of L to L for SSJ-M60- Stations are the same as those of SSJ-M60- Stations U IN rail SSJ-M60- IN rail holding screw Stations Manual override (Non-lock) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L B (S, R, RS) SJ000 pitch P = 0 SJ000 pitch P = 7. 7.(SJ000) [7.(SJ000)]. (SJ000) [ (SJ000)]. (SJ000) [. (SJ000)] Approx. 00 (Lead wire length).6 [(P), (E) port] Applicable tubing O.: ø, ø/6" [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" ø6, ø/" (9.) [(A), (B) port] Applicable tubing O.: ø, ø/" ø, ø/" side (L) (9.6) (SJ000) [(7.) (SJ000)] L dimension: Formula, L to L = 7. x n + 0 x n M = ( + )/. + Remove all numbers after the decimal. L = M x. + L = L 0. L = (L )/ n: Quantity of SJ000 n: Quantity of SJ IN rail 67 IN rail holding screw Manual override (Non-lock) (A) port side: Blue (B) port side: Yellow L (IN rail mounting hole pitch:.) L 7. (SJ000) [7. (SJ000)] Approx. 00 (Lead wire length)

74 Series SJ000/000 Manifold Exploded View Type 60 individual wiring () manifold Note) Refer to page for How to Increase Manifold Stations. SJ Specifications Valve lock switch Manual override switch w q SUP block disk assembly EXH block disk assembly e r side Component Parts/ (Non ) No. escription Internal pilot Internal pilot/built-in silencer SUP/EXH block assembly External pilot External pilot/built-in silencer For different pressures, internal pilot Note ) For different pressures, internal pilot/built-in silencer Note ) End block assembly End block assembly IN rail Part no. SJ000-0-A- SJ000-0-AS- SJ000-0-AR- X, PE port: Metric size ø Inch size ø/" SJ000-0-ARS- X port: Metric size ø Inch size ø/" SJ A- SJ AS- SJ000--A SJ000--A VZ (Metric size) C6: With ø6 (straight) C: With ø (straight) L6: With ø6 (elbow upward entry) L: With ø (elbow upward entry) B6: With ø6 (elbow downward entry) B: With ø (elbow downward entry) (Inch size) N7: With /" (straight) N9: With /6" (straight) For For side Refer to page 7. Note ) The valves cannot be operated only with the SUP/EXH block assembly for different pressure, select them in combination with the SUP/EXH block assembly for internal/ external pilot. Note ) Refer to page 69 about the SUP/EXH block disk assembly and method of handling of parts at different pressure. Note SJA6 Made to Order Manifold Options Specifications/ 6

75 Series SJ000/000 Manifold Options to / SUP block disk assembly By placing a SUP block disk assembly in a manifold valve s pressure supply passage, two different high andlow pressures can be supplied to one manifold. When supplying different pressures using the manifold of the internal pilot, fill out a manifold specification sheet to place an order for an Series Part no. SUP/EXH block assembly for the internal pilot specifications and another SUP/EXH block assembly SJ000 SJ000--A for the different pressure internal pilot specifications (Refer to Circuit iagram ). SJ000 [ifferent pressure pneumatic circuit diagram] The SJ series supplies air to the pilot port of each valve using a (P) port of the SUP/EXH block assembly. When using in situations such as where there are different pressures, combine SUP/EXH block assemblies for internal pilot, external pilot and different-pressure by referring to the circuit below.. ifferent-pressure spec. using the internal pilot (B) (A) (Pilot passage) (P) (E) (B) (A) (B) (A) (P) (E) (B) (A) X X ifferent pressure internal pilot spec. SUP/EXH block assembly. ifferent-pressure spec. using the external pilot (For using the SUP/EXH block assembly for external pilot) Internal pilot spec. SUP/EXH block assembly EXH block disk assembly SUP block disk assembly (P) (E) X (B) (A) (B) (A) (B) (A) (P) (E) (B) (A) X (Pilot passage) X X External pilot spec. SUP/EXH block assembly. ifferent-pressure spec. using the external pilot (For using the SUP/EXH block assembly for different-pressure internal pilot spec.) External pilot spec. SUP/EXH block assembly EXH block disk assembly SUP block disk assembly (P) (E) (B) (A) (B) (A) (B) (A) (P) (E) (B) (A) X (Pilot passage) X X ifferent-pressure internal pilot spec. SUP/EXH block assembly External pilot spec. SUP/EXH block assembly EXH block disk assembly SUP block disk assembly Note ) When operating under the different-pressure spec., supply the higher pressure to the pilot passage. Note ) If there is a need to partition the pilot passage, consult SMC. 69

76 to / EXH block disk assembly By installing an EXH block disk in a manifold valve s exhaust passage, the valve s exhaust can be separated so that it will not affect other valves. Label for block disk These labels are attached to manifolds in which SUP and EXH block disks have been installed, in order to identify the installed locations. (Three sheets each included.) Label for SUP/EXH block disk Blanking block assembly <Connector type/ wiring> Series SJ000/000 Manifold Options SJ000--A Label for SUP block disk These are mounted when later addition of valves is planned, etc. Valve lock switch Label for EXH block disk <Cable type> Series SJ000 SJ000 Valve lock switch Part no. SJ000--A When a block disk is concurrently ordered by specifying on the manifold specification sheet, etc., a label will be stuck on the position where block disk is mounted. Internal pilot spec. for different pressure SUP/EXH block assembly Valve lock switch SJ Specifications Manifold Options No linkage printed circuit board is provided for individual wiring. Series Part no. Note Width SJ000 SJ000 SJ000-9-A SJ000-9-A Connector type (Single wiring) Connector type (ouble wiring) SJA6 Note) SJ000-9-A-N Connector type (ouble wiring) 7. mm SJ000 SJ000-9-A SJ000 wiring SJA6 Note) SJ000-9-A-N Note) Valve lock switch is not available for the SJA6. Silencer with This silencer can be mounted on the manifolds port (E: Exhaust) with a single touch. C øb Series SJ000 SJ000 SJA6 Note) SJ000 Part no. SJ000-9-A SJ000-9-A SJ000-9-A-N SJ000 Width 7. mm 0 mm Note) Valve lock switch is not available for the SJA6. Made to Order SJA6 Specifications/ ø ød A L A Plug These are inserted in unused cylinder ports and P, E ports. ød Series Model Effective area C ød SJ000 For (ø) AN-C0 0 mm mm mm 0 mm ø SJ000 imensions Applicable fitting size ød 6 /" /" /" /6" Model KJP-0 KQP-0 KQP-06 KQP-0 KQP-0 KQP-0 KQP-07 KQP-09 A L (mm)

77 Series SJ000/000 Manifold Options to / IN rail VZ000. L dimension Enter a number from the IN rail dimension table shown below. L (7.) Rail mounting hole pitch. () () No. S 0.. L dimension Weight (g) No. 0 L dimension Weight (g) 0. No. 0 L dimension Weight (g) (Unit: mm) Flat ribbon cable assembly AXT00 FC W 6 6 Terminal no. Triangle mark location (.6) L Red Flat Ribbon Cable Assembly Cable length (L). m m m Connector width (W) 0 pins AXT00-FC0- AXT00-FC0- AXT00-FC pins AXT00-FC0- AXT00-FC0- AXT00-FC0-0 6 pins AXT00-FC6- AXT00-FC6- AXT00-FC6-7. For other commercial connectors, use a type with strain relief that conforms to MIL-C-0. Connector manufacturers: Hirose Electric Co., Ltd. Sumitomo M Limited Fujitsu Limited Japan Aviation Electronics Industry, Ltd. J.S.T. Mfg. Co., Ltd. -sub connector ( pins)/cable assembly AXT00 S L Terminal no. Cable length (L). m m m Socket side -sub Connector Cable Assembly Assembly part no. AXT00-S-0 AXT00-S-00 AXT00-S-00 Note Cable cores x AWG For other commercial connectors, use a pins type with female connector conforming to MIL-C-0. Connector manufacturers: Hirose Electric Co., Ltd. Fujitsu Limited Japan Aviation Electronics Industry, Ltd. J.S.T. Mfg. Co., Ltd. 7 Approx. ø0 x M.6 x 0. Multi-core vinyl cable 0. mm x C Electric Characteristics Item Characteristics Conductor resistance 6 or less Ω/km, 0 C Withstand pressure 000 VAC, min Insulation resistance or less MΩkm, 0 C Note) The minimum bending radius for -sub connector cables is 0 mm. -sub Connector Cable Assembly Cable Color List of Each Terminal No. Terminal no. Lead wire color Black Brown Red Orange Yellow 6 Pink 7 Blue Purple 9 Gray 0 White White Yellow Orange Yellow Pink 6 Blue 7 Purple Gray 9 Orange 0 Red Brown Pink Gray Black White ot marking None None None None None None None White Black Black Red Red Red Black Black White None None Black White White Red Red White None

78 Series SJ000/000 Manifold Options to / ual flow fitting (Set for SJ000 series) SJ000 0 A C Port size C ø N9 ø/6" SJ Specifications This is a fitting for cylinder ports which enables simultaneous actuation and increase in flow rate of valves for stations. This is a with port sizes of ø and ø/6. When arranging mounted to the valve, arrange the valve part no. using the part no. without the, and then add the part no. for the dual flow fitting. If the arrangement is complicated, please specify them by means of the manifold specification sheet. Ordering example Valve type (without ) SJ60-CU- C0 sets SJ000-0-A-C set The asterisk denotes the symbol for assembly. C: ø N9: ø/6" Manifold Options () Made to Order SJA6.. Specifications/ 7

79 Nil N 00 0 M SJ000 spec Connector type wiring Series SJ000/000 Manifold Options For Connector type/ Regulator block/how to Order This is used to reduce the pressure supplied from the side inside the manifold. All valves on the are depressurized from the regulator block. Option Pressure gauge, top mounting Pressure gauge, side mounting Without pressure gauge 00 Regulating port P P port P Valve lock switch Nil N With Without SJ000/000 SJA6 Pressure adjustment screw operation Nil Slotted locking type H Manual Note ) Be sure to apply the pressure from the (P) port of the manifold before using the regulator block. Note ) When ordering with a regulator block installed in the manifold, please order using the manifold specification sheet. SJ000(N)-00-P(-H) With manual operation of pressure adjustment screw SJ000(N)-0-P(-H) SJ000(N)-M-P(-H) Valve lock switch No linkage printed circuit board is provided for individual wiring. Pressure gauge, top mounting Pressure gauge, side mounting Without pressure gauge Flow Characteristics (Conditions: Inlet pressure 0 psi (0.7 MPa) position solenoid valve mounting) SJ000 P port regulation (P A, B) 6 (0.) 0 (0.7) 7 (0.6) 7 (0.) (0.) (0.) 9 (0.) (0.) Outlet pressure psi (MPa) SJ000 P port regulation (P A, B) 6 (0.) 0 (0.7) 7 (0.6) 7 (0.) (0.) (0.) 9 (0.) (0.) Outlet pressure psi (MPa) (0). (0). (60). (0). (00). (0).9 (0).6 (60) (0). (0). (60). (0). (00). (0).9 (0).6 (60) Flow rate scfm (L/min (ANR)) Flow rate scfm (L/min (ANR)) 7

80 MAX.. Series SJ000/000 Manifold Options 6 SJ Specifications Pneumatic circuit (Regulator block mounting example) 0. MPa Regulator block 0. MPa Set to 0. MPa (B) (A) (B) (A) (B) (A) (B) (A) (Pilot passage) (SJ60) (SJ60) (SJ P) (SJ60) (SJ60) P port 0. MPa applied (E) (P) side imensions Note) Reduces supply pressure from the side of manifold. Supply pressure from the cannot be reduced. 0 / MAX.9. (With manual operation) ø side Manifold Options Made to Order With manual operation of the pressure adjustment screw SJA Specifications/ When mounted on the side of the pressure gauge 7

81 For SJ000 Handle (Regulator orientation) A Lateral B Upward Refer to Figure. Fitting size Straight (Metric size) C6: ø6 C: ø (Inch size) N7: ø/"" N9: ø/6"" Elbow fitting (Upward entry) (Metric size) L6: ø6 L: ø elbow fitting Elbow fitting (ownward entry) (Metric size) B6: ø6 elbow fitting B: ø elbow fitting Note) When the handle orientation is lateral, the elbow fitting (upward entry) cannot be selected. Series SJ000/000 Manifold Options 7 SUP/EXH block assembly with regulator and pressure switch (for internal pilot manifold)/how to Order When mounting on the manifold, specify it in the manifold specification sheet. Nil N A spec. For connector type For individual wiring (P) port regulation P Regulator specifications (0 psi (0.7 MPa) specifications) Symbol Nil C Specifications Relieving Non-relieving Pressure switch/pressure gauge specifications Nil A Without pressure display function Analog pressure gauge N Q P S igital pressure switch NPN open collector PNP open collector External wiring Internal wiring External wiring Internal wiring Note ) Internal wiring specifications mean that the wiring is assigned to the centralized wiring on the manifold. (For details, refer to Electrical on page 7.) Note ) For the internal wiring specifications, select an appropriate pressure switch according to the polarity of the valve to be mounted. Note ) For the serial manifold and non plug-in, Q and S (internal wiring specifications) cannot be selected. Note ) The analog pressure gauge is not applicable to the copper-free specifications. N Pressure switch/ Pressure gauge display orientation Nil Without pressure display function F Fitting side side C Coil side U Refer to Figure. Note) If is selected when the connector (-sub connector, flat ribbon cable, PC wire ring) entry direction is upward, the connector may interfere with the pressure switch wiring depending on the mounting position. So, carefully check this point. igital pressure switch option (external wiring) Nil L F Without lead wire with connector With lead wire with connector Note) This option can be selected only when the pressure switch/pressure gauge specifications are N or P. isplay unit Analog pressure gauge: The unit of the product Nil () nameplate and pressure display is MPa. Analog pressure gauge: The unit of the product Z ()() nameplate and pressure display is psi. igital pressure switch: With display unit ZA ()() switching function (Initial valve MPa.) Note ) igital pressure switch, you will (MPa) a fixed unit. Note ) According to the New Measurement Law (SI units are used in Japan), these pressure gauges are sold only to the overseas market. Both MPa and psi are written on the unit display of the digital pressure switch. Note ) The digital pressure switch has the unit conversion function and its initial setting is the psi display. Note ) For digital pressure switches. Regulator handle side Coil side Fitting side (P) port A: Lateral B: Upward Fig. Handle orientation (Regulator mounting orientation) Note ) Be sure to apply the pressure from the (P) port of the manifold before using the SUP/EXH block assembly with regulator and pressure switch. Note ) For details on regulator and electric circuit of the external wiring specifications, see the catalog for Series ARM. Note ) Applicable only to the manifolds with the internal pilot specifications. Note ) This regulator block cannot be combined with the vacuum release valve of Series SJA6. Series SJ000 Valve with Speed Controller/How to Order SJ 60 (T) S Entry is the same as standard products. 0 Note ) Applicable only to Series SJ000. Note ) Specify S0 or S at the end of the valve part no. 7 (E) port Meter-out Meter-in Control method Identification color: Silver Identification color: Black 0 (Arrow marks show the display visual observation directions.) This figure shows the pressure switch F: Fitting side. Fig. Pressure switch/pressure gauge display orientation symbol Identification color position For (A) side (Speed controller) For (B) side (A) port (B) port

82 Flow characteristics Regulator unit flow characteristics SJ000 passage P A/B Outlet pressure psi [MPa] Valve with speed controller flow characteristics Meter-out control A/B E Flow rate scfm [l/min(anr)] (Pilot passage) (SJ60) (B) (A) (SJ60-S) (B) (A) (SJ60-S0) (B) (A) (SJ60) (B) (A) (SJ60) (B) (A) SJ000 passage P A/B Meter-in control P A/B Pneumatic circuit (Installation example of SUP/EXH block assembly with regulator and pressure switch, valve with speed controller) side 0 (0.7) 7 (0.6) 7 (0.) (0.) (0.) 9 (0.) (0.) () Series SJ000/000 Manifold Options.77 (0).6 (7). (00) Outlet flow rate scfm [l/min(anr)]. ().0 (0). (0) 0 psi (0.7 MPa). (00) 7 psi (0. MPa). (0) psi (0. MPa). (60) psi (0. MPa). (0) 0.7 (0) Number of needle rotations [Turns] Outlet pressure psi [MPa] Flow rate scfm [L/min(ANR)] (SJ000B-PCB) (E) (P) Number of needle rotations [Turns] SJ Specifications Manifold Options Made to Order SJA6 Specifications/ 0 (0.7) 7 (0.6) 7 (0.) (0.) (0.) 9 (0.) (0.). (0). (00). (0). (60). (0) 0.7 (0) 0.77 (0). (00).0 (0) Outlet flow rate scfm [l/min(anr)] 0 psi (0.7 MPa) 7 psi (0. MPa) psi (0. MPa) psi (0. MPa) 7.06 (00). (0) Valve with speed controller SUP/EXH block assembly with regulator 76

83 Series SJ000/000 Manifold Options 9 For SUP/EXH block assembly with regulator and pressure switch, valve with speed controller/imensions 0.. [(A), (B) port] Applicable tubing O..: ø,ø/" ø,ø/" ø6,ø/" Speed controller Identification color: Silver (Meter-out) Black (Meter-in) B A B A B A B A Valve with speed controller B A For (B) side For (A) side P (Station ) (Station ) E FREE LOCK (P), (E) port Applicable tubing O..: ø,ø/6" side For lateral handle orientation. Regulator handle Pressure switch SUP/EXH block or pressure gauge assembly with regulator and pressure switch (For -position:.6) 0 6. (0.7) (.) 77 (.).6 (For cable type Note) ) Note) The SUP/EXH block assembly with regulator and pressure switch cannot be mounted on the plug-in cable type manifold. 77

84 Series SJ000/000 Manifold Options 0 SJ Specifications Manifold electrical wiring when the SUP/EXH block assembly with the regulator and pressure switch is mounted. (Internal wiring and pressure switch (NPN)) -sub connector ( pins) (+) Station Station Station OUT ( ) (+) ( ) Pressure sensor (NPN) Flat ribbon cable (0 pins) Flat ribbon cable (6 pins) 6 (+) Station Station Station OUT ( ) (+) ( ) Triangle mark Pressure sensor (NPN) Flat ribbon cable (0 pins) Manifold Options Made to Order 0 (+) 0 (+) Station 9 Station 9 7 Station SJA6 Specifications/ (+) ( ) Pressure sensor (NPN) OUT ( ) Triangle mark Station Station Note ) This figure shows when the SUP/EXH block assembly with the regulator and pressure switch is mounted between the connector block and st station valve. Note ) Applicable only to the connector type manifold. (+) ( ) Pressure sensor (NPN) OUT ( ) Triangle mark 7

85 For connector type Series SJ000/000 Manifold Options Intermediate connector block assembly This connector block can be used by inserting it into the middle of the manifold. This can be used, for example, when you wish to separate electrical control of valves in the same manifold, or when the number of control points is insufficient. Series SJ000 SJ000 Part no. SJ A SJ A SJ A-0 Note) When ordering with an intermediate connector block assembly installed in the manifold, please order using the manifold specification sheet. Intermediate connector block assembly wiring example Note Flat ribbon cable (0 pins) Flat ribbon cable (6 pins) With power supply terminal (for PC wiring) (SJ A) Intermediate connector block 0 9 side Connector block 0 9 For flat ribbon cable (0 pins) ouble solenoid (Station ) ouble solenoid (Station ) COM Station Station ouble solenoid (Station ) ouble solenoid (Station ) Enables control of solenoid valves from the position where the intermediate connector block assembly is installed. imensions. / Applicable connector: 0 pin MIL type with strain relief (MIL-C-0 compliant) side LOCK 77 FREE COM Station Station 79 Intermediate connector block assembly This drawing shows the SJ A.

86 Fluororubber is used for rubber parts of the main valve to allow use in applications such as the following. Part no. Series SJ000/000 Made to Order For detailed dimensions, specifications, and delivery, please contact SMC. Main Valve Fluororubber Specifications. When using a lubricant other than the recommended turbine oil, and there is a possibility of malfunction due to swelling of the spool valve seals.. When ozone enters or is generated in the air supply. SJ 60 (T) X90 Entry is the same as standard products. Note) Because in series -X90 fluororubber is used for only main valve, the rubber parts of the application/usage in conditions requiring heat resistance should be avoided. Symbol -X90 SJ Specifications Made to Order Manifold Options SJA6 Specifications/ 0

87 SJ Vacuum Release Valve with Restrictor Series SJA6 Specifications Type P. Connector Connection P.7 -sub Connector Flat Ribbon Cable PC Serial : EX0 Serial : EX0 Cable Connection -sub Connector Flat Ribbon Cable Manifold Options Made to Order SJA6 Non Type Specifications/ P.9

88 Vacuum Release Valve with Restrictor Series SJA6 Specifications Manifold Valve Specifications Valve construction Fluid Operating pressure range psi (MPa) Release pressure port (P) Vacuum pressure port (E) Pilot X port Ambient and fluid temperature Max. operating frequency (Hz) Manual override (Manual operation) Restrictor operation Pilot method Lubrication Mounting orientation Impact/Vibration resistance (m/s ) Note ) Enclosure position port valve with restrictor Air 6 to 0 (0. to 0.7). to 0 ( 00 kpa to 0.7) Note ) to 0 (0. to 0.7) Note ) to F ( 0 to 0 C) (No freezing) Non-locking push type Push-turn locking slotted type Manual Slotted locking type External pilot/pilot valve individual exhaust Not required Unrestricted 0/0 ustproof Note ) Can be used with positive pressure to suit the application. Note ) Please use with pilot X port pressure equal to or higher than the release port (P) pressure. Note ) Impact resistance: No malfunction occurred when it is tested in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between and 000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Symbol (E) Vacuum X pressure port (P) Release pressure port PS port Solenoid Specifications Coil rated voltage Allowable voltage fluctuation Power Standard consumption (W) With power saving circuit (Continuous duty type) Surge voltage suppressor Indicator type VC, VC ±0% of rated voltage iode LE For the allowable voltage fluctuation for Z/T type (with power saving circuit), please observe the following range because they have voltage drop due to internal circuit. Z type VC: 7% to +0% VC: % to +0% T type VC: % to +0% VC: 6% to +0% Response Time Valve model SJA6- - Weight (B) Vacuum pad port Response time ms (at 7 psi (0. MPa)) 9 or less Valve model Weight (g) SJA6- -P 79 Flow Characteristics Flow Characteristics (When restrictor is fully open) Fluid passage (P) (B) Valve model (B) Port size C[dm /(s bar)] b Cv SJA6- - M Restrictor Flow Characteristics [Fluid passage: (P) (B)]. (0) Flow rate scfm [L/min (ANR)]. (00). (0). (60). (0) 0.7 (0) Inlet pressure: 0 psi (0.7MPa) (B) (E) C[dm /(s bar)] b Inlet pressure: 7 psi 0.MPa Inlet pressure: psi (0.MPa) Inlet pressure: psi (0.MPa) Cv Number of restrictor rotations