5 Port Solenoid Valve

Transcription

1 0 PW COM Rubber Seal Port Solenoid Valve Series SZ000 Cassette Type Manifold The plug-in cassette system makes valve replacement easy. plug-in manifold has been created with a height of. mm (including DIN rail). Valve replacement can be performed easily. Moreover, since spare terminates for wiring (receptacle housings) are contained inside the manifold, terminal changes (additions) can be performed quickly and easily. (The number of additional stations is limited by the manifold specifications. For details, refer to page.) Valves equipped with switches djustment and maintenance of equipment can be performed with greater safety, since the power to each valve can be shut off individually with built-in switches. High speed response of 0 ms SZ000 double, 0. MPa VDC, Without surge Low power consumption and a faster response time of 0 ms are obtained with a unique pilot valve construction. Low power consumption: 0. W (Current draw: m at VDC) Low power consumption enables direct operation by a PLC. Cost savings are realized through the use of a smaller power supply and the elimination of relay cards. Easy attaching/detaching of the tubing The interval between ports and is a wide 0. mm, allowing easy changes of fittings and tubing. The connector entry direction can be changed from top to side with a simple operation. Switch for locking a connector LOCK High reliability and long service life exceeding 0 million cycles or more High reliability and long service life have been achieved with guide ring construction which prevents eccentricity of the main valve, and a return piston with increased return force. (Single and double solenoid type) FREE SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ C/C C/C (Elbow type) Size and weight reduced by eliminating the manifold base LOCK Series SZ000 FREE port port M port block assembly Height Weight % reduction % reduction (Compared with SX000- with DIN rail manifold and stations) Plug-in Type LOCK FREE P. EX0/Serial transmission system P. Non Plug-in Type P. EX0/Serial transmission system LOCK FREE P. Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

2 Port Solenoid Valve Series SZ000 Plug-in Type How to Order Plug-in manifold with power supply terminals SSZ 0 F D 0 U P CE-compliant Connector type Q CE-compliant F: D-sub connector ( pins) LOCK FREE PG: Flat ribbon cable (0 pins) LOCK FREE P: Flat ribbon cable ( pins) LOCK FREE PH: Flat ribbon cable (0 pins) LOCK FREE SUP/EXH block mounting position U U side ( to 0 stations) D ( to 0 stations) oth sides ( to 0 stations) M * Special specifications * For special specifications, indicate separately by the manifold specification sheet. Note) total of up to SUP/EXH blocks can be mounted. Please contact SMC if or more will be mounted. R Pilot type Internal pilot External pilot Power supply terminals Symbol Specifications P VDC, Positive common P VDC, Positive common N VDC, Negative common N VDC, Negative common SUP/EXH block fitting specifications L Option When a longer DIN rail is desired than the specified stations, specify the station number to be required. Straight Elbow fittings (Upward) Elbow fittings (Downward) Valve stations Connector mounting position Symbol Mounting position D F: D-sub connector Symbol Stations 0 stations stations stations 0 stations Note Double wiring specifications () Specified layout () (Up to solenoids possible) P: Flat ribbon cable connector ( pins) Symbol 0 Stations stations Note 0 0 stations stations 0 stations Double wiring specifications Specified layout (Up to solenoids possible) Connector entry direction : Perpendicular connector : Lateral connector LOCK FREE LOCK FREE PG: Flat ribbon cable connector (0 pins) Symbol Stations Note 0 stations 0 0 stations stations stations Double wiring specifications Specified layout (Up to solenoids possible) PH: Flat ribbon cable connector (0 pins) Symbol Stations Note 0 stations stations stations stations Double wiring specifications Specified layout (Up to solenoids possible) Note ) Double wiring specifications: Single, double, position and position solenoid valves can be used at all of the manifold stations. Note ) Specified layout: Indicate wiring specifications on a manifold specification sheet. (Please note that in locations where single solenoid wiring is indicated, it will be impossible to use double or position/ position valves.) Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

3 Cassette Type Manifold Series SZ000 How to Order Plug-in manifold without power supply terminals SSZ 0 F D 0 U Connector type F: D-sub connector ( pins) LOCK FREE PG: Flat ribbon cable (0 pins) LOCK FREE LOCK FREE P: Flat ribbon cable ( pins) LOCK FREE PH: Flat ribbon cable (0 pins) LOCK FREE Connector mounting position Symbol D Mounting position Connector entry direction : Perpendicular connector : Lateral connector LOCK FREE Valve stations SUP/EXH block mounting position U U side ( to 0 stations) D ( to 0 stations) oth sides ( to 0 stations) M Special specifications For special specifications, indicate separately by the manifold specification sheet. Note) total of up to SUP/EXH blocks can be mounted. Please contact SMC if or more will be mounted. F: D-sub connector Symbol Stations 0 stations 0 0 Note PG: Flat ribbon cable connector (0 pins) Symbol Stations Note 0 stations stations stations 0 stations 9 stations stations 9 stations Double wiring specifications () Specified layout () (Up to solenoids possible) Double wiring specifications Specified layout (Up to 9 solenoids possible) Pilot type R Option When a longer DIN rail is desired than the specified stations, specify the station number to be required. SUP/EXH block fitting specifications L Internal pilot External pilot Straight CE-compliant Q Elbow fittings (Upward) Elbow fittings (Downward) CE-compliant P: Flat ribbon cable connector ( pins) Symbol 0 Stations stations Note 0 0 PH: Flat ribbon cable connector (0 pins) Symbol Stations Note 0 stations stations stations 0 stations stations stations 9 stations Double wiring specifications Specified layout (Up to solenoids possible) Double wiring specifications Specified layout (Up to 9 solenoids possible) Note ) Double wiring specifications: Single, double, position and position solenoid valves can be used at all of the manifold stations. Note ) Specified layout: Indicate wiring specifications on a manifold specification sheet. (Please note that in locations where single solenoid wiring is indicated, it will be impossible to use double or position/ position valves.) SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

4 ON SMC Series SZ000 How to Order How to order solenoid valves For plug-in (Common for both with and without power supply terminals) SZ 0 LOZ C Type of actuation position single solenoid C () () () () () () (E)(P)(E) position double solenoid () (E)(P)(E) position closed center () () (E)(P)(E) position exhaust center () () (E)(P)(E) position pressure center () () (E)(P)(E) position dual port valve: N.C./N.C. () SOL.a SOL.b (R) (R) (P) position dual port valve: N.O./N.O. SOL.a SOL.a (R) (R) SOL.b (P) SOL.b (P) () (R) position dual port valve: N.C./N.O. () (R) Rated VDC VDC When using on a manifold with power supply terminals, be sure to match with the manifold s specifications. ack pressure check valve None K uilt-in The built-in back pressure check valve type has an effective area approximately 0% smaller. The position valve is not available with back pressure check valve. Pilot type Internal pilot R External pilot The position dual port valve is not available with external pilot specifications. : Non-locking push type Rated : Without switch J: With switch For switch operation, refer to page 9. Common specifications Positive common N Negative common When using on a manifold with power supply terminals, be sure to match with the manifold s common specifications. Manual override D: Push-turn locking slotted type, port size C: for ø C: for ø M: M x 0. CE-compliant Q CE-compliant Mede to Order Main Valve Fluoro Rubber Specifications X90 (Refer to page 9) Elbow fitting assembly (Upward) L: ø elbow fitting assembly L: ø elbow fitting assembly Elbow fitting assembly (Downward) : ø elbow fitting assembly : ø elbow fitting assembly 0 Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

5 LOCK FREE Cassette Type Manifold Series SZ000 How to Order Valve Manifold ssembly Ordering example (SZ000, positive common with power supply terminals) Double solenoid ( VDC) SZ0-LOZ-C ( sets) SUP/EXH block (U side mounting) Single solenoid ( VDC) SZ0-LOZ-C ( sets) With power supply terminals Plug-in manifold SSZ-0PD-0U-P Stations U side SJ SY SV SYJ Made to Order (Refer to page 9 for details.) Manifold Specifications Model Manifold (P: SUP), / (R: EXH) system Valve stations (With power terminal) pplicable connector Internal wiring (), () port Location Porting specification Direction (P), / (R) port Port size (), () port SSZ-0PD-0U-P set (Manifold part number) SZ0-LOZ-C sets (Single solenoid part no.) SZ0-LOZ-C sets (Double solenoid part no.) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. Stations are counted from as the st one. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. When entry of part numbers becomes complicated, indicate on the manifold specification sheet. D-sub connector Type 0F D-sub connector Conforming to MIL-C-0 JIS-X-0 Type 0P Flat ribbon cable type 0P Plug-in type Common SUP, EXH to 0 stations to stations to stations Flat ribbon cable connector Socket: pins MIL type with strain relief Conforming to MIL-C-0 + COM, COM Valve Lateral, Upward, Downward C C, C, M Type 0PG Flat ribbon cable connector Socket: 0 pins MIL type with strain relief Conforming to MIL-C-0 Type 0PH Flat ribbon cable connector Socket: 0 pins MIL type with strain relief Conforming to MIL-C-0 Weight W (g) () n: Stations W =.n + n + m +. n: Number of SUP/EXH blocks m: Weight of DIN rail Note ) In cases such as those where many valves are operated simultaneously, use type (double side SUP/EXH), applying pressure to the (P) ports on both sides and exhausting from the (R) ports on both sides. Note ) The weight W is the value for the D-sub connector manifold with power supply terminals only. To obtain the weight with solenoid valves attached, add the solenoid valve weights given on page for the appropriate number of stations. For DIN rail weight, refer to page. SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ Flow Characteristics Port size,, (P, E, E) C, (, ) C C b Flow characteristics M Note) The value is for manifold base with stations and individually operated position type. Values inside [ ] are for position dual port valves. Cv b Cv Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

6 Series SZ000 Solenoid Valve Specifications Series Fluid Internal pilot position single operating position double pressure range (MPa) position position dual port valve External pilot Operating pressure range operating Pilot position single pressure range pressure position double (MPa) range position mbient and fluid temperature ( C) position single position double position position dual port valve Weight Valve model SZ 0- -C SZ 0- -C SZ 0- -M Type of actuation SZ000 ir 0. to to to to kpa to to to to 0. 0 to 0 (No freezing. Refer to page.) position single, double Max. operating position dual port valve 0 frequency (Hz) position Manual override (Manual operation) Non-locking push type, Push-turn locking slotted type Pilot type Common exhaust type for main and pilot valve Lubrication Not required Mounting orientation Unrestricted Impact/Vibration resistance m/s Note) 0/0 Enclosure Dust-protected Note) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and deenergized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between and 000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Solenoid Specifications Electrical entry L type (For plug-in), M type plug connector (M) Rated coil (V) Note),,,, VDC llowable fluctuation ±0% of rated Power consumption (W) 0. (With light: 0.) Surge Diode Indicator light LED Note) Only VDC and VDC are available for plug-in use. Response Time Note) ased on dynamic performance test, JIS -9. (Coil temperature: 0 C, at rated ) Response time (ms) (at the pressure of 0. MPa) Type of actuation Without surge position position position position position position position position position or less 0 or less or less 0 or less Single Double Closed center Exhaust center Pressure center Dual port valve Single Double Closed center Exhaust center Pressure center Dual port valve Single Double Closed center Exhaust center Pressure center Dual port valve With surge S, Z type or less or less 0 or less or less Port size (), () C for ø C for ø M x 0. Mass (g) Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

7 Cassette Type Manifold Series SZ000 Manifold Option SUP block disk y installing a SUP block disk in the pressure supply passage of a manifold valve, it is possible to supply two or more different high and low pressures to one manifold. (Use in combination with a pilot port block disk.) lanking block assembly SZ000-- These are mounted when later addition of valves is planned, etc. Series SZ000 Part no. SZ000-- EXH block disk y installing an EXH block disk in the exhaust passage of a manifold valve, it is possible to divide the valve s exhaust so that it does not affect another valve. (Two block disks are needed to divide both exhausts.) Label for block disk SZ000-- Series SZ000 Series SZ000 Part no. SZ000-- Pilot port block disk y installing a pilot port block disk in the pilot passage of a manifold valve, it can be function as an internal pilot/external pilot mixed manifold. Label for SUP/EXH block disk Label for EXH block disk Part no. SZ000-- The labels shown below are used on manifold stations containing SUP/EXH block disk(s) to show their location. ( pcs. each) Label for SUP block disk Label for pilot port block disk When a block disk is concurrently ordered by specifying on the manifold specification sheet, etc., a label will be stuck on the position where block disk is mounted. Silencer with This silencer can be mounted on the manifolds port R (exhaust) with a single touch. C Series SZ000 (ø) Dimensions pplicable fittings size ød ød Plug (White) Model N0-KM L Model L D KQP-0 KQP-0 KQP-0 Effective area mm ø These are inserted in cylinder ports or SUP/EXH ports which are not being used. Purchasing order is available in units of 0 pieces. 0. ød 9 C 0 SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ LOCK FREE Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

8 Series SZ000 Manifold Option DIN rail dimensions/mass VZ Refer to the L dimension tables Enter a number from the DIN rail dimension table below. L (.) D-sub connector ( pins)/cable assembly XT00-DS L. () ().0 SMC No. L dimension Mass (g) No. L dimension Mass (g) No. L dimension Mass (g) XT00-FC - to W Flat Ribbon Cable ssembly Cable length (L). m m m Connector width (W) Rail mounting hole pitch pins XT00-FC0- XT00-FC0- XT00-FC0-. (.) L pins XT00-FC0- XT00-FC0- XT00-FC Flat ribbon cable type/cable assembly Terminal no. Triangle mark position Red pins XT00-FC- XT00-FC- XT00-FC-. For other commercial connectors, use a type with strain relief conforming to MIL-C-0. Connector manufacturers example Hirose Electric Co., Ltd. Sumitomo M Limited Fujitsu Limited Japan viation Electronics Industry, Ltd. J.S.T. Mfg. Co., Ltd. Terminal no. Cable length (L). m m m Socket side Terminal no. Lead wire color lack rown Red Orange Yellow Pink lue Purple 9 Gray 0 White White Yellow Orange Yellow Pink lue Purple Gray 9 Orange 0 Red rown Pink Gray lack White D-sub Connector Cable ssembly ssmbly part no. XT00-DS-0 XT00-DS-00 XT00-DS-00 x M. x 0. D-sub Connector Cable ssembly Terminal No. Dot marking None None None None None None None White lack lack Red Red Red lack lack White None None lack White White Red Red White None Note Cable cores x WG For other commercial connectors, use a pins type with female connector conforming to MIL-C- 0. Connector manufacturers example Hirose Electric Co., Ltd. Fujitsu Limited Japan viation Electronics Industry, Ltd. J.S.T. Mfg. Co., Ltd. Multi-core vinyl cable 0. mm x C Electric Characteristics Item Characteristics or less Voltage limit VC, min. 000 or less Note) The minimum bending radius for D-sub connector cables is 0 mm. Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

9 Cassette Type Manifold Series SZ000 Manifold Electrical Wiring Type 0F D-sub Connector Type ( pins) Without Power Supply Terminal With Power Supply Terminal Positive common Negative common Common Station Station Station Station Type 0P Flat Ribbon Cable Type ( pins) Without Power Supply Terminal Common Station Triangle mark 0 Positive common Positive pin (Common) Negative pin With Power Supply Terminal Positive pin (Common) Negative pin Station Triangle mark 0 Positive pin Negative common Negative pin (Common) The common polarity should be the same as the common specifications of the valve to be used. The maximum number of stations that can be Power supply terminal Power supply terminal accommodated is 0 manifold stations, with up to solenoids. The maximum number of stations that can be accommodated is 0 manifold stations, with up to solenoids. The circuits above are for the double wiring specifications with up to 0 or stations. Connect to in the case of a single solenoid. Moreover, when wiring instructions are given on a manifold specification sheet, the signal for single and the, signals for double should be wired in order,,,...etc., without skipping or leaving any connectors remaining. Stations are counted from as the st one. Station Station Station Station 0 Station Station Station Station Station 0 Station Station Positive pin Negative pin (Common) Station Station Station Triangle mark SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ The common polarity should be the same as the common specifications of the valve to be used. Power supply terminal Power supply terminal The maximum number of stations that can be accommodated is 0 manifold stations, with up to solenoids. The maximum number of stations that can be accommodated is 0 manifold stations, with up to solenoids. The circuits above are for the double wiring specifications with up to or stations. Connect to in the case of a single solenoid. Moreover, when wiring instructions are given on a manifold specification sheet, the signal for single and the, signals for double should be wired in order,,,...etc., without skipping or leaving any connectors remaining. Stations are counted from as the st one. Since terminal numbers are not indicated on the flat cable, use the triangle mark as a reference for wiring. Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

10 Series SZ000 Manifold Electrical Wiring Type 0PG Flat Ribbon Cable Type (0 pins) Without Power Supply Terminal With Power Supply Terminal Positive common Negative common 0 Common 0 Positive pin (Common) 0 Positive pin 9 Station 9 Station 9 Negative pin Station 9 Negative pin (Common) Station Station Station Station Station Triangle mark Station Triangle mark Station Triangle mark The common polarity should be the same as the common specifications of the valve to be used. The maximum number of stations that can be accommodated is 9 manifold stations, with up to 9 solenoids. Power supply terminal Power supply terminal The maximum number of stations that can be accommodated is manifold stations, with up to solenoids. The circuits above are for the double wiring specifications with up to or 9 stations. Connect to in the case of a single solenoid. Moreover, when wiring instructions are given on a manifold specification sheet, the signal for single and the, signals for double should be wired in order,,,...etc., without skipping or leaving any connectors remaining. Stations are counted from as the st one. Since terminal numbers are not indicated on the flat cable, use the triangle mark as a reference for wiring. Type 0PH Flat Ribbon Cable Type (0 pins) Without Power Supply Terminal With Power Supply Terminal Positive common Negative common 0 9 Common 0 9 Positive pin (Common) Negative pin 0 9 Positive pin Negative pin (Common) Station Station Station Station Station Station Station Triangle mark Station Triangle mark Station Triangle mark The common polarity should be the same as the common specifications of the valve to be used. The maximum number of stations that can be accommodated is 9 manifold stations, with up to 9 solenoids. Power supply terminal Power supply terminal The maximum number of stations that can be accommodated is manifold stations, with up to solenoids. The circuits above are for the double wiring specifications with up to stations. Connect to in the case of a single solenoid. Moreover, when wiring instructions are given on a manifold specification sheet, the signal for single and the, signals for double should be wired in order,,,...etc., without skipping or leaving any connectors remaining. Stations are counted from as the st one. Since terminal numbers are not indicated on the flat cable, use the triangle mark as a reference for wiring. Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

11 Cassette Type Manifold Series SZ000 Wiring of Plug-in Type Manifold with Power Supply Terminal (Example) Since the power supply to drive valves with power supply terminals can be supplied from either the control side or the manifold side, these wiring examples should be used for reference when wiring is performed.. Wiring example when using manifold power supply terminal PLC (Programmable Logic Controller) Manifold valve (SSZ-0PGD-0U- ). Wiring example when not using manifold power supply terminal (Power is supplied to the control side or along the wiring, etc.) PLC (Programmable Logic Controller) Manifold valve (SSZ-0PGD-0U- ) DC power supply Solenoid Valve DC power supply SZ manifold internal wiring (Flat ribbon cable, Positive common specifications) 0 9 Negative pin Power supply terminal Power supply 0 Positive pin 9 Triangle mark SZ manifold internal wiring (Flat ribbon cable, Positive common specifications) Control side (PLC, etc.) (NPN open collector output) COM Cable assembly XT00-FC0-, etc. Power supply Control side (PLC, etc.) (NPN open collector output) COM SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ Solenoid Valve Power supply terminal Triangle mark Cable assembly XT00-FC0-, etc. Caution Single wire, COM position, etc. of PLC are different from each manufacturer. When connecting with PLC, read the specifications carefully and understand the electrical circuit. Poor wiring could cause damage to PLC, power source, etc. as well as manifold and valve. Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

12 Series SZ000 Construction JIS Symbol position single position single with () () back pressure check valve () () position single r e w t y q u!0 o (E) (P)(E) (E) (P)(E) () () JIS Symbol position double () () (E) (P)(E) JIS Symbol position closed center position double with back pressure check valve () () (E) (P)(E) position double (E) (P) (E) r e w t y q u!0 o i () () () () (E) (P)(E) position exhaust center (E) (P) (E) i () () position closed center/exhaust center/pressure center (E) (P)(E) r e w t y q u!0 o position pressure center () () () (E) (P)(E) () (E) (P) (E) i Component Parts No. Description Material Note ody Zinc die-casted dapter plate Resin Urban white Pilot body Resin Urban white Molded coil Urban gray ody cover Resin Urban white Spool valve assembly luminum/hnr Port block Resin Urban white ottom cover assembly Urban white Replacement Parts No. Description Part no. 9 Refer to part number information on page 9. 0 Clip SX000-- position single with back pressure check valve r e w t y q u!0 o (E) (E) (P) i () () Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

13 Cassette Type Manifold Series SZ000 JIS Symbol position dual port valve SZ0 [N.C. valve x pcs.] () () SZ0 [N.C. valve x pcs.] y t r u q q e i!!0 SOL.a (R) SOL.b (R) (P) SZ0K/With back pressure check valve () () SOL.a (R) SOL.b (R) (P) SZ0 [N.C. valve x pcs.] () () SOL.a (R) SOL.b (R) (P) SZ0K/With back pressure check valve () () SOL.a (R) SOL.b (R) (P) SZC0 [N.C. valve, N.O. valve pc. each] () () SOL.a (R) SOL.b (R) (P) SZC0K/With back pressure check valve () () SOL.a (R) SOL.b (R) SZ0 [N.O. valve x pcs.] (R) (R) (P) y t r u w w e i!!0 (R) (R) (P) SZC0 [N.C. valve, N.O. valve pc. each] y t r u q w e i!!0 o o SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ (P) (R) (P) (R) o Component Parts No. 9 Replacement Parts No. 0 Description Spool valve assembly Spool valve assembly ody dapter plate Pilot body Molded coil ody cover Port block ottom cover assembly Description Clip Material Resin/HNR Resin/HNR Zinc die-casted Resin Resin Resin Resin Note For N.C. (Normally closed) For N.O. (Normally open) Urban white Urban white Urban gray Urban white Urban white Urban white Part no. Refer to part number information on page 9. SX000-- SZ0K/With back pressure check valve y t r u q q e i!!0 (E) (E) (P) o Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

14 Series SZ000 Manifold Exploded View Type 0P Manifold (Plug-in, flat ribbon cable type) w q U side t r u e Component Parts No. Description Part no. SUP/EXH block assembly SZ End block assembly Housing holder SUP block bush assembly SUP block bush assembly DIN rail Connector block assembly SZ000-- SX000-- SZ000-- SZ000-- VZ SZ000-- Note C: With for ø C: With for ø L: With for ø (Elbow fetching upward) L: With for ø (Elbow fetching upward) : With for ø (Elbow fetching downward) : With for ø (Elbow fetching downward) Refer to page. Refer to connector block assembly part no. table below. y Connector lock ssembly Part No. Connector specifications Mounting position Part no. Without power supply terminals With power supply terminals Note For D-sub connector For flat ribbon cable pins SZ SZ D D P N SZ D - P N SZ D - : Perpendicular connector : Lateral connector P: Positive common N: Negative common For flat ribbon cable 0 pins For flat ribbon cable 0 pins For serial SZ SZ SZ D D D P N SZ D - P N SZ D - Note) The assembly part numbers with power supply terminals are VDC specifications. If VDC specifications are required, enter at the end of the assembly part number. Note) Connector block assembly can be shipped as an assembly only in the case of double wiring. Since the possible number of stations differs depending on the connector type, refer to the valve station section on catalog pages, 9, and, and enter the number of stations in the section of the assembly part number. Please contact SMC if a connector block assembly is required having a wiring specification other than double wiring. 0 Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

15 Cassette Type Manifold Series SZ000 Plug-in Manifold Station Expansion Caution In addition to solenoid valves, housing holders (SX000--) are necessary for expansion of manifold stations. Double wiring specifications manifolds which do not have the maximum number of stations, contain spare receptacle housings for expansion in the housing holder of the last station, or inside the supply/exhaust block assembly (for a maximum of stations). When expanding stations, perform the disassembly and assembly of the manifold while referring to the expansion method shown below. () Loosen the DIN rail holding screw if the end block on the U side. Receptacle housing U side End block SUP/EXH block Contains receptacle housings for expansion Housing holder (SX000--) Use caution to the bushes for junction not to fall.. lign connectors. () () () Separate the end block and SUP/EXH block. Take out the receptacle housing for expansion which is inside the SUP/EXH block, attach it to the newly added housing holder, and attach to the manifold. (Numbers are displayed on the side of the receptacle housings, and they should be used in order from the lowest number.) Mount the valve on the DIN rail.. ttach to rail by pushing on coil area.. Hook on rail. SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ () While pressing the manifold together from both sides, refasten the side U end block s DIN rail holding screw. Caution (Tightening torque:. N m) Press the manifold. Press the manifold. Caution.e sure to shut off the power and air supplies before disassembly. Furthermore, since air may remain inside the actuator, piping and manifold, confirm that the air is completely exhausted before performing any work..when disassembly and assembly are performed, air leakage may result if connections between blocks and tightening of the end block s holding screw, is inadequate. efore supplying air, confirm that there are no gaps, etc. between blocks, and that manifold blocks are securely fastened to the DIN rail. Then supply air and confirm that there is no air leakage before operating..note that for manifolds specified with other than double wiring, spare receptacle housings for expansion are not included unless indicated at the time of order. Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

16 Series SZ000 Dimensions: SZ000 Plug-in SSZ-0FD - Stations U-. (Pitch) P=0. [(), () port] pplicable tubing O.D.: ø ø With external pilot. FREE R... [(P), (R) port] pplicable tubing O.D.: ø P PE M x 0. [(), () port] (X, PE ports) pplicable tubing O.D.: ø X P R pplicable connector: JIS-X-0 MIL-C-0 D-sub equivalent L (L). Switch for locking a connector (.). LOCK Terminal no.. DIN rail.9 Manual override Press and turn for the locking type.. (): Orange (): Green L (Rail mounting hole pitch.) L DIN rail holding screw Power supply terminals (M terminal screws). (With switch mounted). The indication marking is for VDC. (Station n) (Station ) side: Orange side: Green.9. ON ON (.) (DIN rail dimension). (9.) Note) For manifold dimensions with elbow fitting, refer to page. Switch (When equipped with switch) Internal Pilot Manifold L Dimension L n L L L L n: Stations External Pilot Manifold L Dimension L n L L L L n: Stations Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

17 Cassette Type Manifold Series SZ000 Dimensions: SZ000 Plug-in SSZ-0FD - Stations -. (Pitch) P=0. [(P), (R) port] pplicable tubing O.D.: ø With external pilot. (.) 0. [(), () port] pplicable tubing O.D.: ø ø.... DIN rail side: Orange side: Green. R P L R P M x 0. [(), () port] Switch for locking a connector (Station n) (Station ) ON ON. Manual override Press and turn for the locking type. (): Orange (): Green L (Rail mounting hole pitch.) L FREE LOCK (L).9. (.) (DIN rail dimension). (9.). (X, PE ports) pplicable tubing O.D.: ø DIN rail holding screw Power supply terminals (M terminal screws)... (With switch mounted) R PE X P pplicable connector: Terminal no..9. R P JIS-X-0 MIL-C-0 Note) For manifold dimensions with elbow fitting, refer to page.. The indication marking is for VDC. D-sub equivalent SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ Switch (When equipped with switch) Internal Pilot Manifold L Dimension L n L L L L n: Stations External Pilot Manifold L Dimension L n L L L L n: Stations Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

18 Series SZ000 Dimensions: SZ000 Plug-in SSZ-0FD - Stations U- ( pins). (Pitch) P=0. M x 0. [ (), () port] With external pilot. X P PE R FREE P R.. [(P), (R) port] pplicable tubing O.D.: ø [(), () port] pplicable tubing O.D.: ø ø (X, PE ports) pplicable tubing O.D.: ø. L Switch for locking a connector. (L) (.).. LOCK... pplicable connector: pins MIL type With strain relief (Conforming to MIL-C-0) DIN rail Manual override Press and turn for the locking type. (): Orange (): Green L (Rail mounting hole pitch.) L (Station n) (Station ). DIN rail holding screw Power supply terminals (M terminal screws) 0.. (When equipped with switch) Triangle mark.9 pplicable connector: 0 pins MIL type With strain relief (Conforming to MIL-C-0).. The indication marking is for VDC. Triangle mark position pplicable connector: 0 pins MIL type With strain relief (Conforming to MIL-C-0) side: Orange side: Green.9 Internal Pilot Manifold L Dimension L n L L L L ON ON (.) (DIN rail dimension). n: Stations (.) Switch (When equipped with switch) 0PG (0 pins) 0PH (0 pins) Note ) Types 0PG and 0PH differ only in their connectors, and the L through L dimensions are the same as type 0P. Note ) For manifold dimensions with elbow fitting, refer to page. External Pilot Manifold L Dimension L n L L L L Triangle mark position Triangle mark position n: Stations Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

19 Cassette Type Manifold Series SZ000 Dimensions: SZ000 Plug-in SSZ-0FD - Stations - ( pins). (Pitch) P=0. M x 0. [(), () port] [(P), (R) port] pplicable tubing O.D.: ø. With external pilot (.). 0.. DIN rail.. R P [(), () port] pplicable tubing O.D.: ø ø L Switch for locking a connector R P (Station n) (Station ) side: Orange side: Green.. FREE LOCK (L) Manual override Press and turn for the locking type. (): Orange (): Green L (Rail mounting hole pitch.) L Power supply terminals (M terminal screws).9. DIN rail holding screw. R P (X, PE ports) pplicable tubing O.D.: ø... (When equipped with switch Triangle mark.9 PE X pplicable connector: 0 pins MIL type With strain relief (Conforming to MIL-C-0) R P pplicable connector: pins MIL type With strain relief (Conforming to MIL-C-0).. The indication marking is for VDC. Triangle mark position pplicable connector: 0 pins MIL type With strain relief (Conforming to MIL-C-0) SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ. Internal Pilot Manifold L Dimension L n L L L L ON. 9 ON. 9. Switch (When equipped with switch) (.) (DIN rail dimension). (.) Triangle mark position Triangle mark position 0PG (0 pins) 0PH (0 pins) Note ) Types 0PG and 0PH differ only in their connectors, and the L through L dimensions are the same as type 0P. Note ) For manifold dimensions with elbow fitting, refer to page. n: Stations External Pilot Manifold L Dimension L n L L L L n: Stations Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

20 Series SZ000 Dimensions with Elbow Fitting: SZ000 Plug-in, D-sub Connector L SSZ-0FD - Stations U - (The fitting dimension of the flat cable and non plug-in types is the same.). (Pitch) P=0. LOCK (.). 0. (.9).. (R) Port () port (P) port [ (P), (R) Port ] pplicable tubing O.D.: ø () port FREE [Valve]. (.) (). [Supply/Exhaust block]. () (P) () (R) (.). () (.) U side Downward (Type ). (Station n) (Station ) (.) (DIN rail dimension) Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

21 Port Solenoid Valve Non Plug-in Type Series SZ000 How to Order Non plug-in manifold SJ SSZ 0 0 U CE-compliant SY SV 0 0 Stations stations 0 stations SUP/EXH block mounting position D U M * ( to 0 stations) U side ( to 0 stations) oth sides ( to 0 stations) Special specifications * For special specifications, indicate separately by the manifold specification sheet. SUP/EXH block fitting specifications Straight L Elbow type (Upward) Elbow type (Downward) Pilot type Internal pilot R External pilot Q CE-compliant Option When a longer DIN rail is desired than the specified stations, specify the station number to be required. SYJ SZ VP S000 VQ VQ VQ VQC How to Order Valve Manifold ssembly Ordering example (SZ000, Non plug-in) VQZ SQ SUP/EXH block (U side mounting) Double solenoid ( VDC) SZ0-MZ-C (sets) Single solenoid ( VDC) SZ0-MZ-C (sets) VFS VFR VQ U side Stations SSZ-0-0U set (Manifold part number) * SZ0-MZ-C sets (Single solenoid part no.) * SZ0-MZ-C sets (Double solenoid part no.) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. Stations are counted from as the st one. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. When entry of part numbers becomes complicated, indicate on the manifold specification sheet. Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

22 Series SZ000 How to Order SZ 0 M C Type of actuation C position single solenoid () position double solenoid () () (E)(P)(E) () (E)(P)(E) position closed center () () (E)(P)(E) position exhaust center () () (E)(P)(E) position pressure center SOL.a () () (E)(P)(E) position dual port valve: N.C./N.C. () () SOL.b position dual port valve: N.O./N.O. SOL.a SOL.b position dual port valve: N.C./N.O. SOL.a (R) () (R) () (R) (P) (P) SOL.b (P) (R) () (R) () (R) Pilot type Internal pilot R External pilot The position dual port valve is not available with external pilot specifications. ack pressure check valve None K uilt-in The built-in back pressure check valve type has an effective area approximately 0% smaller. The position valve is not available with back pressure check valve. Rated VDC VDC V VDC S VDC R VDC Common specifications Positive common N Negative common The symbol is when not equipped with light/surge. Electrical entry Manual override : Non-locking push type D: Push-turn locking slotted type Without light/surge With surge S With light/surge Z M: With lead wire (Length 00 mm) MN: Without lead wire, port size C: for ø C: for ø M: M x 0. CE-compliant Q CE-compliant Made to Order Main Valve Fluoro X90 Rubber Specifications (Refe to page 9.) Elbow fitting assembly (Upward) L: ø elbow fitting assembly L: ø elbow fitting assembly Elbow fitting assembly (Downward) : ø elbow fitting assembly : ø elbow fitting assembly MO: Without connector COM COM Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

23 Cassette Type Manifold Series SZ000 Manifold Specifications Model Type SSZ-0 Made to Order Specifications (For details, refer to page 9.) Manifold (P: SUP), / (R: EXH) system Valve stations (), () port Porting specifications Port size Mass W (g) () Location Direction (P), /(R) port (), () port n: Number of SUP/EXH blocks m: Weight of DIN rail Flow Characteristics Port size,, (P, E, E) C, (, ) C C b Non plug-in type Common SUP, EXH to 0 stations Valve Lateral, Upward, Downward C C, C, M W = n + m + 9 Note ) In cases such as those where many valves are operated simultaneously, use type (double side SUP/EXH), applying pressure to the (P) ports on both sides and exhausting from the (R) ports on both sides. Note ) The mass W is the value for the D-sub connector manifold with power supply terminals only. To obtain the mass with solenoid valves attached, add the solenoid valve mass given on page for the appropriate number of stations. For DIN rail mass, refer to page. Flow characteristics Cv M Note) The value is for manifold base with stations and individually operated position type. Values inside [ ] are for position dual port valves. b Cv SJ SY SV SYJ SZ VP S000 VQ VQ VQ VQC VQZ SQ VFS VFR VQ Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

24 Series SZ000 Manifold Exploded View Type 0 (Non plug-in) manifold U side DIN rail holding screw q e t r w DIN rail holding screw Component Parts No. Description End block assembly End block assembly SUP block bush assembly SUP block bush assembly DIN rail Part no. SUP/EXH block assembly SZ SZ000-- SZ000-- SZ000-- SZ000-- VZ Note C: With for ø C: With for ø L: With for ø (Elbow fetching upward) L: With for ø (Elbow fetching upward) : With for ø (Elbow fetching downward) : With for ø (Elbow fetching downward) U side Refer to page. y Manifold Station Expansion Station expansion is possible at any position. () Loosen one DIN rail holding screw on either U side or. () Separate the blocks at the location where station expansion is desired. () Mount the valve on the DIN rail. () While pressing the manifold together from both sides, retighten the DIN rail holding screw of the end block assembly which was loosened. Caution (Tightening torque:. N m) Caution. e sure to shut off the power and air supplies before disassembly. Furthermore, since air may remain inside the actuator, piping and manifold, confirm that the air is completely exhausted before performing any work.. When disassembly and assembly are performed, air leakage may result if connections between blocks and tightening of the end block s holding screw, is inadequate. efore supplying air, confirm that there are no gaps, etc. between blocks, and that manifold blocks are securely fastened to the DIN rail. Then supply air and confirm that there is no air leakage before operating. 0 Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

25 Cassette Type Manifold Series SZ000 Dimensions: SZ000 Non Plug-in SSZ-0- Stations U. (Pitch) P=0. [(), () port] pplicable tubing O.D.: ø ø. With external pilot. [(P), (R) port] pplicable tubing O.D.: ø R P... R P (X, PE ports) pplicable tubing O.D.: ø X PE SJ SY SV SYJ (.) U side L (L). SZ VP S000 VQ VQ VQ DIN rail COM COM COM COM COM Manual override Press and turn for the locking type. (): Orange (): Green L (Rail mounting hole pitch.) L DIN rail holding screw 00 Lead wire length. VQC VQZ SQ VFS VFR VQ (Station n) (Station ) side: Orange side: Green. (.) (DIN rail dimension) Note) For manifold dimensions with elbow fitting, refer to page. Internal Pilot Manifold L Dimension L n L L L L n: Stations External Pilot Manifold L Dimension L n L L L L n: Stations Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

26 Series SZ000 Dimensions: SZ000 Non Plug-in SSZ-0- Stations D (Pitch) P=0.. [(P), (R) port] pplicable tubing O.D.: ø With external pilot... P R P X R PE [(), () port] pplicable tubing O.D.: ø ø (.) (X, PE ports) pplicable tubing O.D.: ø U side L. (L) COM COM COM COM COM DIN rail Manual override Press and turn for the locking type. (): Orange (): Green L (Rail mounting hole pitch.) DIN rail holding screw 00 Lead wire length. L (Station n) (Station ) side: Orange side: Green. (.) (DIN rail dimension) Note) For manifold dimensions with elbow fitting, refer to page. Internal Pilot Manifold L Dimension L n L L L L n: Stations External Pilot Manifold L Dimension L n L L L L n: Stations Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

27 Cassette Type Manifold Series SZ000 Dimensions: SZ000 Non Plug-in SSZ-0- Stations. (Pitch) P=0. [(P), (R) port] pplicable tubing O.D.: ø With external pilot... R R. R PE R SJ P [(), () port] pplicable tubing O.D.: ø ø (.).. U side L P. (L)... P (X, PE ports) pplicable tubing O.D.: ø X P SY SV SYJ SZ VP S000 VQ VQ VQ DIN rail COM COM COM COM COM Manual override Press and turn for the locking type. : Orange : Green L (Rail mounting hole pitch.) L DIN rail holding screw 00 Lead wire length. VQC VQZ SQ VFS VFR (Station n) (Station ) VQ side: Orange side: Green. (.) (DIN rail dimension) Note) For manifold dimensions with elbow fitting, refer to page. Internal Pilot Manifold L Dimension L n L L L L n: Stations External Pilot Manifold L Dimension L n L L L L n: Stations Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)

28 Type0S Port Solenoid Valve EX0 Integrated Type (for Output) Serial Transmission System Series SZ000 How to Order Manifold SI unit specifications Symbol Protocol type 0 Without SI unit F NKE Corp.: Uni-wire System ( output points) SSZ 0S Q SI unit mounting position D D This should be indicated even without SI unit. 0 NKE Corp.: H Valve stations Uni-wire H System Symbol Stations Note SUNX Corp.: J 0 stations S-LINK ( output points) J SUNX Corp.: Double wiring specification S-LINK ( output points) 0 stations Q Device Net 0 stations Specified layout OMRON Corp.: R Compous/S System ( output points) (Up to solenoids possible.) stations OMRON Corp.: R Note ) Double wiring specifications: Compous/S System ( output points) Single, double, position and V CC-LINK position solenoid valves can be used at all of the manifold stations. Note ) Specified layout: Indicate wiring specifications on the manifold specification sheet. (Note that double, and position valves cannot be used where single solenoid wiring has been specified.) Note ) R and J are available with up to solenoids. SI unit part no. Symbol Protocol type SI unit part no. CE-compliant F NKE Corp.: Uni-wire System EX0-SUW H NKE Corp.: Uni-wire H System EX0-SUH J SUNX Corp.: S-LINK ( output points) EX0-SSL J SUNX Corp.: S-LINK ( output points) EX0-SSL Q Device Net EX0-SDN R OMRON Corp.: Compous/S ( output points) EX0-SCS R OMRON Corp.: Compous/S ( output points) EX0-SCS V CC-LINK EX0-SMJ U SUP/EXH block mounting position U U side ( to 0 stations) D ( to 0 stations) oth sides ( to stations) M Special specifications For special specifications, indicate separately by the manifold specification sheet. Note) total of up to SUP/EXH blocks can be mounted. Please contact SMC if or more will be mounted. CE-compliant Q CE-compliant Option When a longer DIN rail is desired than the specified stations, specify the station number to be required. SUP/EXH block fitting specifications Straight L Elbow type (Upward) Elbow type (Downward) Pilot type Internal pilot R External pilot How to Order Valve Manifold ssembly Ordering example (Compo us/s compatible SI unit) SUP/EXH block assembly (U side mounting) Double solenoid ( VDC) SZ0-LOZ-C ( sets) Single solenoid ( VDC) SZ0-LOZ-C ( sets) SSZ-0SRD-0U SZ0-LOZ-C SZ0-LOZ-C set (manifold part number) sets (Single solenoid part no.) sets (Double solenoid part no.) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. U side Stations Stations are counted from as the st one. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. When entry of part numbers becomes complicated, indicate on the manifold specification sheet. SI unit ( mounting) Refer to pages and for the details of EX0 integrated type (for output) serial transmission system. Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C Main Office: (0) -900-Outside Local rea: (00)