5 Port Direct Operated Poppet Solenoid Valve, Rubber Seal

Transcription

1 Port Direct Operated Poppet Solenoid Valve, Rubber Seal Series 3000 or details about certified products conforming to international standards, visit us at C: 0.4 dm 3 /(s bar) (Passage {4/ /3 (A/B R/R)}) Compact: Width 8 x Length 68 (mm) Low power consumption 4 W DC (Standard type) W DC (Low wattage type) Suitable for copper-free applications All the parts in contact with fluid are non-copper materials JIS Symbol Body ported Base mounted Body ported Base mounted Specifications Type of actuation luid Ambient and fluid temperature Response time (at the pressure of 0. MPa) () Manual override Lubrication Mounting orientation Impact/Vibration resistance () Enclosure Solenoid Specifications Direct operated type position single solenoid Air 0 to 0 C (No freezing. Refer to page ) 0 ms or less (Standard), ms or less (Low wattage type) Non-locking push type Not required (Use turbine oil Class ISO V3, if lubricated.) Unrestricted 300/0 m/s Dustproof Note ) Based on dynamic performance test, JIS B (Coil temperature: 0 C, at rated voltage, without surge suppressor) Note ) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 4 and 000 Hz. Test was performed at both energized energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Electrical entry Rated voltage (V) Allowable voltage fluctuation Apparent power (AC) Power consumption (DC) Surge voltage suppressor Indicator light At the rated voltage AC DC Inrush Holding W/o indicator light W/ indicator light AC DC AC DC rommet (), DIN terminal (D) 00, 0, 00, 0, 40 6,, 4, 48 ±0% of rated voltage 9. VA/0 Hz, 8 VA/60 Hz 7 VA/0 Hz, VA/60 Hz 4 W (Standard), W (Low wattage) 4.3 W (Standard),.3 W (Low wattage) Varistor Diode ( VDC or less: Varistor) Neon bulb LED S S N Mounting with 300 Series 300 can be mounted on the same manifold base VVK3 of 3000 series. or details, refer to the page Used as a 3 Port Valve Series 3000 can be used as 3 port valve, as a N.C. or N.O. type, by plugging either A or B cylinder Port. Make sure not to plug the exhaust port R. low Characteristics/Weight Body ported Valve model 30 30Y (or low wattage W DC) Base 340 mounted 340Y (with sub-plate) (or low wattage W DC) Operating pressure range (MPa) 0 to 0.7 low characteristics 4/ (P A/B) 4/ /3 (A/B R/R) Port size b Cv b Cv C [dm 3 / (s bar)] C [dm 3 / (s bar)] M x M x Weight (g) rommet Plug position Type of actuation B port N. C. A port N. O. JIS symbol Plug Plug 3--

2 Electrical entry : rommet (Lead wire length: 300 mm) H: rommet (Lead wire length: 600 mm) D: DIN terminal DO: DIN terminal (Without connector) or connector part number, refer to page 3--. Body ported 30 M Base mounted Construction JIS Symbol Rated voltage 00 VAC, 0/60 Hz 00 VAC, 0/60 Hz 0 VAC, 0/60 Hz 0 VAC, 0/60 Hz 4 VDC VDC 40 VAC, 0/60 Hz 9 Other Option Y Option M M x R, R: M Valve option Standard or low wattage ( W DC) Port size (P, A and B port) Port size Option None With bracket (Not assembled) 0 8 (With sub-plate) Without sub-plate Light/Surge voltage suppressor None S With surge voltage suppressor With light/surge voltage Z suppressor (Type D only) Since the indicator light is built in the connector, thus, DOZ is not available. Option Part No. Description Part no. Note Bracket A With screw N T Component Parts No. Description Material q Body Aluminum die-casted w e Cover End cover Resin Resin r Spool valve assembly Aluminum, NBR t Return spring Stainless steel y Molded coil Resin Note Platinum silver Black Black Black 3--

3 Manifold Specifications VVK A, B port /8, M x 0.8 Type 334 Type 340 VVK M Common SUP/Common EXH Type 0: Body ported (A, B port top ported) Type 40: Base mounted (A, B port bottom ported) Type 4: Base mounted (A, B port side ported) Type S4 B port: M x 0.8 A port: M x 0.8 A port: M x 0.8 B port: M x 0.8 Type 334 Type 340 A port: M x 0.8 B port: M x 0.8 A port: /8, M x Type 340 Type 334 Specifications Common SUP, Common EXH Piping method Common SUP, Individual EXH VVK station 0 0 stations 00 00N 00T VVK M VVK3 0 station Solenoid direction Solenoid on same side of A and B port Solenoid on same S side of A and B port 0 0 stations stations Port size M M x 0.8 C4 ø4 cassette to 0 Body ported, Base mounted Body ported N T 4 0 M station N T Applicable solenoid valve 30 M M 33 0 Applicable blanking plate assembly A Applicable solenoid valve Applicable blanking plate assembly A Applicable solenoid valve Applicable blanking plate assembly A S S N Type 4: Base mounted (A, B port side ported) Type S4 B port: /8 A port: /8 A port: /8 B port: /8 Type 334 Type 340 Type 340 Type 334 VVK Solenoid direction S Solenoid on same side of A and B port Solenoid on same side of A and B port 0 station 0 0 stations Port size 0 8 C6 ø6 cassette N T Applicable solenoid valve Applicable blanking plate assembly A Common SUP/Individual EXH Type : Body ported (A, B port top ported) A, B port: /8, M x 0.8 R port: M x 0.8 R port: M x 0.8 A port: /8, M x VVK3 0 0 station 0 0 stations N T Applicable solenoid valve 30 M M 33 0 Applicable blanking plate assembly A 3--3

4 Combinations of Solenoid Valve, Manifold asket and Manifold Base port body ported: 30 port base mounted: 340 M3 x 6 Round head combination screw DXT M3 x 6 Round head combination screw Combination of Blanking Plate Assembly and Manifold Base Blanking plate assembly: A M3 x 8 Round head combination screw Blanking plate Manifold gasket Applicable base Type VVK3-0 Type VVK3- Manifold base Manifold gasket Applicable base Sub-plate Type VVK3-40 Type VVK3-(S)4 Manifold base Type VVK3-(S)4 Manifold gasket for blanking plate Applicable base: In common for all types of VVK3 models Manifold gasket Screw assembly Body ported A Base mounted A Note) Mounting direction is not flexible. Make sure to mount them in the right direction. Mounting Screw Tightening Torques M3: 0.6 N m Mounting Screw Tightening Torques M3: 0.6 N m Mixed Mounting of 300 and Manifold Base of Series 3000 Type VVK3-0 Type VVK3-40. In the case of VVK3-0/40 When installing the 3 port valve on the manifold base, plug the R port at the corresponding mark side with the rubber plug ( ) as shown in the figures on the right.. Other manifold 3 port valve except VVK3-0 and 40 types can be mounted without any work. Note ) Remove the plug if changing the 3 port valve to a port valve. Note ) In case a 3 port valve 300 is mounted on the manifold base for a port valve 3000, switching type is normally closed (N.C.). If requiring a normally open type (N.O.), plug the A port on the port valve. Note 3) A port of a 3 port valve for base mounted type becomes A port of a port valve. Plug that A port to avoid mistaking B port for the A port. Plug Corresponding mark (Concave part) Plug Corresponding mark (Concave part) Mounting Screw Tightening Torques M3: 0.6 N m 3--4

5 Port Direct Operated Poppet Solenoid Valve Rubber Seal Series 3000 Dimensions: Body Ported rommet: 30- -M Port size: M DIN terminal: 30- D-M (Bracket) Max. 0 -M. x 0.4 (Mounting screw) (Mounting screw) -ø3. (Manifold mounting hole) Manual override (Non-locking) (Lead wire length) -ø3. (Manifold mounting hole) Applicable cable O.D. : ø3. to ø7 Mounting ( screw ) -ø3. ( ) Mounting hole S S (Breather hole) -M x 0.8 (Piping port) Refer to grommet type for other dimensions. N rommet: Port size: 8 DIN terminal: 30- D-0 (Bracket) -M. x 0.4 (Mounting screw) 3-RC /8 (P, A, B port) -ø3. (Manifold mounting hole) Manual override (Non-locking) (Mounting screw) (Lead wire length) -ø3. (Manifold mounting hole) 3-RC /8 (P, A, B port) Applicable cable O.D.: ø3. to ø7 (Breather hole) Mounting ( hole) Mounting ( screw ) -M x 0.8 (R, R port) Refer to grommet type for other dimensions. 3--

6 Dimensions: Base Mounted rommet: DIN terminal: 340- D-0 ~ = Refer to grommet type for other dimensions. 3--6

7 Port Direct Operated Poppet Solenoid Valve Rubber Seal Series 3000 Type 0 Manifold Body ported (Top ported) VVK3-0- Station n = Number of 3000 n = Number of 300 rommet: DIN terminal: D n /8 (A,Bport) ( ) ( ) S S L L Dimension L L n n: Stations N Type Manifold VVK3-- Station Body ported (Top ported) rommet: DIN terminal: D (P port) (P port) n = Number of 3000 n = Number of 300 L L Dimension L L n n: Stations

8 Type 40 Manifold Base mounted (Bottom ported) VVK3-40- Station -M rommet: DIN terminal: D ( ) ( ) L Dimension L L L n n: Stations

9 Port Direct Operated Poppet Solenoid Valve Rubber Seal Series 3000 Type 4 Manifold Base mounted (Side ported) VVK3-4- Station -M rommet: DIN terminal: D ~= Built-in One-touch fitting: VVK3-4- Station -C4 Solenoid is at the same side as A port: VVK3-S4- Station - S S N L L L n Refer to the above drawing for DIN terminal dimensions Refer to the above drawing for other dimensions

10 Type 4 Manifold Base mounted (Side ported) VVK3-4- Station -0 rommet: DIN terminal: D Built-in One-touch fitting: VVK3-4- Station -C6 Solenoid is at the same side as A port: VVK3-S4- Station - L L L n Refer to the above drawing for DIN terminal dimensions Refer to the above drawing for other dimensions

11 Port Direct Operated Poppet Solenoid Valve Rubber Seal Precautions Series 3000 Be sure to read before handling. or Safety Instructions and Solenoid Valve Precautions, refer to page How to Wire DIN Terminal Connection. Loosen the set screw and pull out the connector from the terminal block of the solenoid.. Remove screw and insert screwdriver into the slit area near the bottom of terminal block to separate block and housing. 3. Loosen the terminal screws (slotted screws) on the terminal block, insert the core of the lead wire into the terminal, and attach securely with the terminal screws. 4. Tighten the ground nut to secure the wire. Use caution in wiring because it will not meet the IP6 (enclosure) standard if you use the other cord than prescribed heavyduty cord of size (ø3. to ø7.). Tighten the ground nut and set screw within the specified range of torque. Change of electrical entry (Orientation) After separating terminal block and housing, the cord entry direction can be changed by attaching the housing in the desired direction (4 directions in 90 increments). In the case of w/indicator light, avoid damaging the light with lead wire. Precautions Plug a connector in or out vertically, never at an angle. Applicable cable O.D. ø3. to ø7 (Reference) 0. mm core and 3 core wires equivalent to JIS C 3306 Circuit with light AC Circuit diagram NL: Neon light R: Resister Rated voltage AC 4 V 48 V DC 6 V V DC W/o indicator light With indicator light W/o indicator light With indicator light W/o indicator light With indicator light VDC or less Circuit diagram LED: Emitting diode R: Resister rommet type () None None None 4 VDC or more Circuit diagram D: Protective diode LED: Emitting diode R: Resister Light/Surge Voltage Suppressor DIN terminal (D) Part no. symbol S Z S Z S Z rommet type DIN terminal Markings or AC, VDC or less or 4 VDC or more Valve Mounting Direction Warning When mounting a valve or spacer on the manifold base or sub-plate, etc., those mounting directions are determined. If mounted in the wrong direction, the equipment to be connected may cause malfunction. Refer to external dimensions in pages 3--4 to 3--0, and then mount it. How to Calculate the low Rate or obtaining the flow rate, refer to page S S N Connector part no.: Part no. of connector with light Rated voltage Voltage symbol 00 VAC 00V 0 VAC 0V 00 VAC 00V 0 VAC 0V 40 VAC 40V 6 VDC 6V VDC V 4 VDC 4VD 48 VDC 48VD Part no Precautions on connection for 4 VDC or more rommet type should be connected as following; Red lead wire for (+) side, Black lead wire for ( ) side respectively. With the DIN terminal, connect the positive (+) side to the connector s no. terminal, and the negative ( ) side to the no. terminal. [Refer to the marks on the terminal board.] or VDC or below, there is no positive (+) or negative ( ) directionality. 3--