CAT.E152-5 Port Solenoid Valve/Body Ported Cassette Type Manifold. Series SZ3000

Transcription

1 CAT.E- Port Solenoid Valve/Body Ported Cassette Type Manifold Series SZ000

2 The plug-in cassette system makes valve replacement easy. A plug-in manifold has been realized having a manifold height of.mm (including DIN rail). Valve replacement can be performed easily. Moreover, since spare terminals for wiring are contained inside the manifold (receptacle housing), terminal changes (expansion) can be performed quickly and easily. (The number of expansion stations is limited by the manifold specifications. Refer to page for details.) Valves equipped with switches Adjustment and maintenance of equipment can be performed with greater safety, since the power to each valve can be shut off individually with built-in switches. The connector entry direction can be changed from top to side with a simple operation. High speed response of 0ms SZ000 single, 0.MPa VDC, without surge While having a low power consumption, a fast response time of 0ms is obtained through a unique pilot valve construction. Low power consumption of 0.6W (current value: ma VDC) By making possible direct drive from a PLC, relays, etc. become unnecessary, and cost savings can also be realized through reductions in the size of the switching element and power supply. Features High reliability and long life of 0 million cycles or more High reliability and long life have been achieved by a guide ring construction, which prevents eccentricity of the main valve, and a return piston with increased return force. (Single and double solenoid types) Copper free There is no copper in fluid contact areas, making it possible to use standard products as they are.

3 New design and bright color tones The top of the manifold has been made flat and the rounding of corners has been enlarged, resulting in a design which is easy on workers. Furthermore, bright color tones using shades of white have been adopted to match the changes in operating environments. Port Solenoid Valve/Body Ported Cassette Type Manifold Series SZ000 Easy attaching/detaching of tubes The interval between ports A and B is a wide 0.mm, allowing easy attaching and detaching of tubes. Size and weight reduction C/C6 One-touch fitting has been realized by eliminating the manifold base M port block Series Height Weight SZ000 % reduction % reduction (Compared with SX000- with DIN rail manifold and stations) Port A Port B One-touch fittings can be changed Series SZ000 Replaceable port sizes C C6 M Pilot valve exhaust mist and noise eliminated (main valve/pilot valve converging exhaust construction) Since the pilot valve exhaust is not discharged directly to the outside, there is no discharge of effluent or harsh exhaust noise from the pilot exhaust port, making the valve "environmentally friendly". Improved moisture resistance A special rubber with outstanding water resistance is used in the main valve area. Trouble in the main valve area is reduced under a wide range of operating conditions. (Rubber with ozone resistant specifications is also separately available.) Features

4 TUV Rheinland BAUART GEPRUFT TYPE APPROVED TUV Approved Product Conforms to standards necessary to satisfy EC directives. The SZ series has received approval for conformity to standards related to EMC Directives and DIN VDE 00, from TUV Rheinland, an EC Notified Body (EC authorization No. 097). Moreover, since the rated for this series is 0VDC or less, it is not subject to low directives. When ordering TUV approved products, add " Q" at the end of the standard part number. Example of how to order a valve SZ Q Enter the standard part number TUV approved product Example of how to order a manifold SSZ Q Enter the standard part number TUV approved product Note) Contact SMC for details, as there are limitations on product models, specifications and electrical entry, etc. Features

5 Port Solenoid Valve Series SZ000 Plug-in Type Plug-in manifold with power supply terminals How to Order SSZ 60 F D 0 U P Connector type F: D-Sub connector ( pins) PG: Flat cable (0 pins) P: Flat cable (6 pins) PH: Flat cable (0 pins) Supply/Exhaust block mounting position U U Side ( to 0 stations) D D Side ( to 0 stations) B Both sides ( to 0 stations) M Special specifications In the case of special specifications, indicate separately on a manifold specification sheet. Note) A total of up to supply/exhaust blocks can be mounted. Contact SMC if or more will be mounted. Options When a DIN rail is required that is longer than the standard types, specify the number of stations. Power supply terminal specifications Symbol Specifications P VDC, positive common P VDC, positive common N VDC, negative common N VDC, negative common Pilot specifications Nil R Internal pilot specifications External pilot specifications Valve stations Connector mounting position Symbol D Mounting position D Side F: D-sub connector Symbol Stations 0 stations stations stations stations Note Note ) Double wiring specification Note ) Specified layout (up to solenoids possible) P: Flat cable connector (6 pins) Symbol 0 Stations stations Note Double wiring specification stations stations Specified layout (up to solenoids possible) 0 0 stations Connector entry direction : Vertical connector : Horizontal connector PG: Flat cable connector (0 pins) Symbol Stations Note 0 stations Double wiring specification 0 stations 09 9 stations Specified layout (up to solenoids possible) stations PH: Flat cable connector (0 pins) Symbol Stations stations... stations stations... stations Note Double wiring specification Specified layout (up to solenoids possible) Note ) Double wiring specifications: Single, double and position solenoid valves can be used at all of the manifold stations. Note ) Specified layout: Indicate the wiring specifications on a manifold specification sheet. (Please note that in locations where single solenoid wiring is indicated, it will be impossible to use double or position valves.)

6 ON OFF SMC Series SZ000 Plug-in manifold [without power supply terminals] Connector type F: D-sub connector ( pins) PG: Flat cable (0 pins) SSZ 60 F D 0 U P: Flat cable (6 pins) Connector entry direction PH: Flat cable (0 pins) Connector mounting position Symbol D Mounting position D Side : Vertical connector : Horizontal connector Supply/Exhaust block mounting position U D B M Valve stations F: D-sub connector Symbol Stations 0 stations stations stations stations U Side ( to 0 stations) D Side ( to 0 stations) Both sides ( to 0 stations) Special specifications In the case of special specifications, indicate separately on a manifold specification sheet. Note) A total of up to supply/exhaust blocks can be mounted. Contact SMC if or more will be mounted. Note Note ) Double wiring specification Note ) Specified wiring (up to solenoids possible) PG: Flat cable connector (0 pins) Symbol Stations Note 0 stations Double wiring specification 09 9 stations 0 0 stations Specified wiring (up to 9 solenoids possible) 9 9 stations Options Pilot specifications Nil Internal pilot specifications R External pilot specifications P: Flat cable connector (6 pins) Symbol 0 Stations stations Note stations Double wiring specification stations Specified wiring (up to solenoids possible) 0 0 stations PH: Flat cable connector (0 pins) Symbol Stations 0 stations stations 0 stations stations When a DIN rail is required that is longer than the standard types, specify the number of stations. Note Double wiring specification Specified wiring (up to 9 solenoids possible) Note ) Double wiring specifications: Single, double and position solenoid valves can be used at all of the manifold stations. Note ) Specified layout: Indicate the wiring specifications on a manifold specification sheet. (Please note that in locations where single solenoid wiring is indicated, it will be impossible to use double or position valves.) How to order solenoid valves For plug-in (common for both with and without power supply terminals) SZ 60 LOZ C6 Switching system Pilot specifications Nil R position single solenoid position double solenoid position closed center position exhaust center position pressure center Rated Internal pilot External pilot VDC 6 VDC Note ) When using on a manifold with power supply terminals, be sure to match with the manifold's specifications. Common specifications Nil N Pos. common Neg. common Note ) When using on a manifold with power supply terminals, be sure to match with the manifold's common specifications. Switch specifications Nil: Without switch J: With switch Refer to page regarding switch operation. A, B port size C ø One-touch fitting C6 ø6 One-touch fitting M M x 0. Manual override Nil: Non-locking push type D: Push and turn locking type Screw driver operated

7 Cassette Type Manifold Series SZ000 How to Order Manifold Assemblies (Example) Example (SZ000, positive common with power supply terminals) Double solenoid (VDC) SZ60-LOZ-C6 (set) Supply/Exhaust block (U side mounting) Single solenoid (VDC) SZ0-LOZ-C6 (set) Plug-in manifold with power supply terminals SSZ-60PD-0U-P D Side Stations U Side SSZ-60PD-0U-P... set (manifold part number) SZ0-LOZ-C6... sets (single solenoid part number) SZ60-LOZ-C6... sets (double solenoid part number) The symbol indicates built-in. Put the symbol at the beginning of the part numbers for solenoid valves, etc. which are to be attached. Valve stations are numbered from station on D side. Indicate the valves to be attached below the manifold part number, in order starting from station as shown in the drawing. When a layout becomes complicated, please indicate on a manifold specification sheet. (Manifold specification sheet on page.) Manifold specifications A, B port piping specifications Port size Model Manifold type P(SUP), R(EXH) system Valve stations Valve effective sectional area mm² (Cv value) Applicable connector Internal wiring C C6 M Location Direction P, R ports A/B ports P A/B A/B R P A/B A/B R P A/B A/B R Note ) Weight W(g) n: Stations n: Number of supply/exhaust blocks m : Weight of DIN rail D-sub connector Type 60F D-sub connector Complies with MIL-C-0 JIS-X-0 Flat cable type 60P Type 60P Type 60PG Plug-in type Common SUP, EXH to 0 stations to stations to stations Flat cable connector Socket: 6 pin MIL type with strain relief Complies with MIL-C-0 Valve Lateral C C, C6, M.(0.9).(0.).7(0.).9(0.).(0.9).(0.) Flat cable connector Socket: 0 pin MIL type with strain relief Complies with MIL-C-0 +COM, COM W =.n + n + m + 6. Type 60PH Flat cable connector Socket: 0 pin MIL type with strain relief Complies with MIL-C-0 Note ) In cases such as those where many valves are operated simultaneously, use type B (double side supply/exhaust), applying pressure to the P ports on both sides and exhausting from the R ports on both sides. Note ) The value is for manifold base mounting ( stations). position type with single action. Note ) The weight W is the value for the D-sub connector manifold with power supply terminals only. To obtain the weight with solenoid valves attached, add the solenoid valve weights given on page 6 for the appropriate number of stations. Refer to page 6 for the weight of DIN rails.

8 Series SZ000 Solenoid Valve Specifications Series Fluid Internal pilot operating pressure range MPa{kgf/cm } External pilot operating pressure range MPa{kgf/cm } position single position double position Operating pressure range Pilot position single pressure position double range position Fluid temperature C Max. operating position single, double frequency Hz position Manual override Pilot system Lubrication Mounting position Impact/Vibration resistance m/s Enclosure SZ000 Air 0. to 0.7 {. to 7.} 0. to 0.7 { to 7.} 0. to 0.7 { to 7.} 00kPa to 0.7 {0Torr to 7.} 0. to 0.7 {. to 7.} 0. to 0.7 {. to 7.} 0. to 0.7 {. to 7.} Maximum 0 Non-locking push type, Screw driver operated push & turn locking type Main valve, Pilot valve convergent exhaust type Not required Unrestricted 0/0 (. to 000Hz) Dust proof Note) Impact resistance: No malfunction when tested with a drop tester in the axial direction of the main valve and moving parts of the magnet core, and at right angles, one time each in both an energized and deenergized condition. (Initial value.) Vibration resistance: No malfunction when tested with one sweep of. to 000Hz in the axial direction of the main valve and moving parts of the magnet core, and at right angles, one time each in both an energized and deenergized condition. (Initial value.) Solenoid Specifications Electrical entry L type (for plug-in), M type plug connector (M) Rated coil V Note),, 6,, DC Allowable fluctuation ±0% of rated Power consumption W 0.6 (with light: 0.6) Surge Diode Indicator light LED Note) Only V and VDC are available for plug-in use. Response Time Note) Based on JISB7-9 dynamic performance test (with coil temperature of 0 C and at rated ). Switching system position single position double position Response time ms (at 0.MPa {.kgf/cm²}) Without surge or less 0 or less or less With surge S, Z type or less or less 0 or less Weight Table Valve model SZ 60- -C SZ 60- -C6 SZ 60- -M position position position position position position Switching system Single Double Closed center Exhaust center Pressure center Single Double Closed center Exhaust center Pressure center Single Double Closed center Exhaust center Pressure center Port size A, B C ø One-touch fitting C6 ø6 One-touch fitting M x 0. Weight g

9 A A A A B Cassette Type Manifold Series SZ000 Manifold Options SUP blocking disk By installing a SUP blocking disk in the pressure supply passage of a manifold valve, it is possible to supply more than two different high and low pressures to one manifold. Blanking block assembly SZ000--A These are mounted when later addition of valves is planned, etc. Series SZ000 Part No. SZ000--A EXH blocking disk By installing an EXH blocking disk in the exhaust passage of a manifold valve, it is possible to divide the valve's exhaust so that it does not affect another valve. (Two blocking disk are needed to divide both exhausts.) Pilot port blocking disk Series SZ000 Part No. SZ000--A By installing a pilot port blocking disk in the pilot passage of a manifold valve, it can function as an internal pilot/external pilot mixed manifold. Silencer with One-touch fitting This silencer can be mounted on the manifold's port R (exhaust) with a single touch. C B A Series SZ000 Part No. SZ000--A Series for SZ000(ø) Model Effective sectional area AN0-KM mm² A ø B 6 C Indicator stickers for blocking disk These stickers are to be put on valves in which SUP and EXH blocking disk have been installed so that confirmation is possible from the outside. (pcs. of each are included.) SZ000--A Sticker for SUP/EXH blocking disk Sticker for EXH blocking disk Plugs (White) These are inserted in cylinder ports or SUP/EXH ports which are not being used. They can be ordered in multiples of 0 pieces. ød ød A Sticker for SUP blocking disk Sticker for pilot passage blocking disk L If blocking disk are ordered on manifold specification sheets, etc. at the same time that manifolds are ordered, stickers will be attached to the valves with blocking disk installed before shipment. Dimension table Applicable fitting size ød 6 Model A L D KQP-0 KQP-06 KQP A B

10 Series SZ000 DIN rail dimension table/weight table VVZS000-A- L 0 6 VZ Refer to the L dimension table Enter a number from the DIN rail dimension table below in the. L (7.) D-sub connector ( pins)/cable assembly 7.0 ~. No. Dimension L Weight (g) Flat cable type/cable assembly AXT00-FC - Triangle mark position 6 6 Flat cable assembly Cable length (L).m m m Connector width (W) Terminal No No. 0 Dimension L. 60. Weight (g) pins AXT00-FC0- AXT00-FC0- AXT00-FC pins AXT00-FC0- AXT00-FC0- AXT00-FC0-0 Sample of connector manufacturers HIROSE ELECTRIC COMPANY SUMITOMO/-M LIMITED FUJITSU LTD. Japan Aviation Electronics Industry, Ltd. J.S.T. Mfg. Co., Ltd. () () No Dimension L Weight (g) W Rail mounting hole pitch. ~ (.6) Red 6 pins AXT00-FC6- AXT00-FC6- AXT00-FC6-7. If it is desired to use a commercially available connector, use one conforming to MIL-C-0 with strain relief. L Socket side Terminal No. Connector HDBB-S (HIROSE ELECTRIC COMPANY) D-sub connector cable assembly Cable length (L).m m m D-sub connector cable assembly wire colors by terminal number Terminal No. Lead wire color Dot marking Black None Brown None Red None Orange None Yellow None 6 Pink None 7 Blue None Purple White 9 Gray Black 0 White Black White Red Yellow Red Orange Red Yellow Black Pink Black Blue White Purple None Gray None 9 Orange Black 0 Red White Brown White Pink Red Gray Red Black White White None Assembly No. VVZS000-A- VVZS000-A- VVZS000-A- -M.6 x 0. Plug connector HDB-CTF (HIROSE ELECTRIC COMPANY) Note Cable cores xawg If it is desired to use a commercially available cable, use a pin female type connector conforming to MIL-C0. Sample of connector manufacturers HIROSE ELECTRIC COMPANY FUJITSU LTD. Japan Aviation Electronics Industry, Ltd. J.S.T. Mfg. Co., Ltd. Approx. ø0 Vinyl multicore cable VVRF 0.mm² x C Electrical characteristics Item Conductor resistance Ω/km, 0 C Withstand VAC for min. Insulation resistance MΩkm, 0 C Characteristic 6 or less 000 or less Note) The minimum inside bending radius for the D-sub connector cable is 0mm. 6

11 Cassette Type Manifold Series SZ000 Manifold Electrical Wiring 60F D-sub connector type ( pins) Without power supply terminals With power supply terminals Positive common Negative common Common Station Station Station Station 0 Pos. pin (common) Neg. pin Station 0 Station Station 0 Pos. pin Neg. pin (common) Station 0 Station Station The common polarity should be the same as the common specifications of the valve to be used. The maximum number of stations that can be accommodated is 0 manifold stations, with up to solenoids. + Power supply terminals + Power supply terminals The maximum number of stations that can be accommodated is 0 manifold stations, with up to solenoids. The circuit above is for the double wiring specification with up to 0 or stations. Connect to in the case of a single solenoid. Moreover, when wiring instructions are given on a manifold specification sheet, the A signal for single and the A, B signals for double should be wired in order,,,...etc., without skipping or leaving any connectors remaining. Stations are counted starting with station on D side. 60P Flat cable type (6 pins) Without power supply terminals With power supply terminals Positive common Negative common 6 Common Station Station Station Station Triangle mark 6 Pos. pin (common) Neg. pin Station Station Station Triangle mark 6 Pos. pin Neg. pin (common) Station Station Station Triangle mark The common polarity should be the same as the common specifications of the valve to be used. The maximum number of stations that can be accommodated is 0 manifold stations, with up to + + Power supply terminals Power supply terminals The maximum number of stations that can be accommodated is 0 manifold stations, with up to solenoids. The circuit above is for the double wiring specification with up to or stations. Connect to in the case of a single solenoid. Moreover, when wiring instructions are given on a manifold specification sheet, the A signal for single and the A, B signals for double should be wired in order,,,...etc., without skipping or leaving any connectors remaining. Stations are counted starting with station on D side. Since terminal numbers are not indicated on the flat cable, use the triangle mark as a reference when wiring. 7

12 Series SZ000 Manifold Electrical Wiring 60PG Flat cable type (0 pins) Without power supply terminals With power supply terminals Positive common Negative common 0 9 Common Station 9 Station Station Station Triangle mark 0 9 Pos. pin (common) Neg. pin Station Station Station Triangle mark 0 9 Pos. pin Neg. pin (common) Station Station Station Triangle mark The common polarity should be the same as the common specifications of the valve to be used. The maximum number of stations that can be accommodated is 9 manifold stations, with up to 9 solenoids. + + Power supply terminals Power supply terminals The maximum number of stations that can be accommodated is manifold stations, with up to solenoids. The circuit above is for the double wiring specification with up to or 9 stations. Connect to in the case of a single solenoid. Moreover, when wiring instructions are given on a manifold specification sheet, the A signal for single and the A, B signals for double should be wired in order,,,...etc., without skipping or leaving any connectors remaining. Stations are counted starting with station on D side. Since terminal numbers are not indicated on the flat cable, use the triangle mark as a reference when wiring. 60PH Flat cable type (0 pins) Without power supply terminals With power supply terminals Positive common Negative common 0 9 Common 0 9 Pos. pin (common) Neg. pin 0 9 Pos. pin Neg. pin (common) 7 Station Station Station Triangle mark 7 Station Station Station Triangle mark 7 Station Station Station Triangle mark The common polarity should be the same as the common specifications of the valve to be used. The maximum number of stations that can be accommodated is 9 manifold stations, with up to 9 solenoids. + + Power supply terminals Power supply terminals The maximum number of stations that can be accommodated is manifold stations, with up to solenoids. The circuit above is for the double wiring specification with up to stations. Connect to in the case of a single solenoid. Moreover, when wiring instructions are given on a manifold specification sheet, the A signal for single and the A, B signals for double should be wired in order,,,...etc., without skipping or leaving any connectors remaining. Stations are counted starting with station on D side. Since terminal numbers are not indicated on the flat cable, use the triangle mark as a reference when wiring.

13 Cassette Type Manifold Series SZ000 Wiring of Plug-in Type Manifold with Power Supply Terminals (Examples) Since the power supply to drive valves with power supply terminals can be supplied from either the control side or the manifold side, these wiring examples should be used for reference when wiring is performed.. Wiring example when using manifold power supply terminals PLC SZ manifold internal wiring (flat cable, positive common specifications) Control side (PLC, etc.) (NPN open collector output) Manifold valve (SSZ-60PGD-0U- ) 0 9 Neg. pin COM 6 DC power supply Solenoid valve + Power supply terminals + Power supply Cable assembly AXT00-FC0- Triangle mark, etc.. Wiring example when not using manifold power supply terminals (power is supplied to the control side or along the wiring, etc.) PLC SZ manifold internal wiring (flat cable, positive common specifications) 9 0 Pos. pin Power supply + Control side (PLC, etc.) (NPN open collector output) COM Manifold valve (SSZ-60PGD-0U- ) DC power supply 6 Solenoid valve + Power supply terminals Cable assembly AXT00-FC0-, etc. Triangle mark When connecting to a PLC (Programmable Logic Controller), etc., the wiring of the signal lines and COM position, etc. will differ with each manufacturer. Connections should be made after thoroughly reviewing the electrical circuits of both units in their catalogs, etc. If connections are made incorrectly, failure may occur not only in the manifolds and valves, etc., but also in the PLC (control side) and power supply, etc. 9

14 Series SZ000 Construction JIS symbol position single (A) (B) position single r e w t y q u!0 o (EA) (P) (EB) (A) (B) JIS symbol position double (A) (B) (EA) (P) (EB) JIS symbol position closed center (EA) (EB) (P) i position double r e w t y q u!0 o (A) (A) (B) (B) (EA) (P) (EB) position exhaust center (EA) (P) (EB) i (A) (B) position closed center/exhaust center/pressure center (EA) (P) (EB) position pressure center r e w t y q u!0 o (A) (B) (A) (EA) (P) (EB) (B) (EA) (P) (EB) i Parts list No. Description Body Adapter plate Pilot body Molded coil Body cover 6 Spool valve assembly 7 Port block Bottom cover assembly Material Die-cast zinc PBT PA PA Aluminum/NBR PA Note Urban white Urban white Urban gray Urban white Urban white Urban white Replacement parts list No. Description Part No. 9 0 One-touch fitting Clip Refer to One-touch fitting part number information on page. SX

15 Cassette Type Manifold Series SZ000 Manifold Exploded View 60P manifold (plug-in, flat cable type) w q U side t r u e D side y Parts list No. Description Supply/exhaust block assembly End block assembly Housing holder Bushing assembly Bushing assembly 6 DIN rail 7 Connector block assembly Part No. SZ000-0-A- SZ000--A SX000-- SZ000--A SZ000--A VZ SZ C6 C Note C6: with ø6 One-touch fitting, C: with ø One-touch fitting Refer to page 6. Refer to the connector block assembly part no. table below. Connector block assembly part number table Connector specifications For D-sub connector For flat cable 6 pins For flat cable 0 pins For flat cable 0 pins Mounting position D side D side D side D side Part No. Without power supply terminals With power supply terminals SZ000-0-A- D SZ000-0-A- D SZ000-0-A- D SZ A- D SZ000-0-A- D - SZ000-0-A- D - SZ A- D - SZ000-0-A- D - P N P N P N P N Note : Vertical connector : Horizontal connector P: Positive common N: Negative common Note) The assembly part numbers with power supply terminals are VDC specifications. If VDC specifications are required, enter "" at the end of the assembly part number. Note ) A connector block assembly can be shipped as an assembly only in the case of double wiring. Since the possible number of stations differs depending on the connector type, refer to the valve station section on catalog page and enter the number of stations in the section of the assembly part number. Contact SMC if a connector block assembly is required having a wiring specification other than double wiring.

16 Series SZ000 Plug-in Manifold Station Expansion In addition to solenoid valves, housing holders (SX000--) are necessary for expansion of manifold stations. Double wiring specification manifolds which do not have the maximum number of stations, contain spare receptacle housings for expansion in the housing holder of the last station, or inside the supply/exhaust block assembly (for a maximum of stations). When expanding stations, perform the disassembly and assembly of the manifold while referring to the expansion method shown below.. Loosen the DIN rail holding screw of the end block on U side. U Side End block Supply/exhaust block. Separate the end block and supply/exhaust block. Contains receptacle housing for expansion. Take out the receptacle housing for expansion which is inside the supply/exhaust block, attach it to the newly added housing holder, and attach to the manifold. (Number are displayed on the side of the receptacle housings, and they should be used in order from the lowest number.) Receptacle housing D Side Housing holder (SX000--) Take care that connection bushing does not fall out. Mount the valve on the DIN rail.. Attach to rail by pushing on coil area. Align connectors. Hook on rail. While pressing the manifold together from both sides, refasten the side U end block's DIN rail holding screw. (fastening torque:.nm) Press manifold inward Press manifold inward. Be sure to shut off the power and air supplies before disassembling. Since air may remain inside actuators, piping and manifolds, confirm that the air is completely exhausted before beginning work.. When disassembly and assembly are performed, air leakage may result if connections between blocks and tightening of the end block's holding screw, etc. are inadequate. Before supplying air, confirm that there are no gaps, etc. between blocks, and that manifold blocks are securely fastened to the DIN rail. Then, supply air and confirm that there is no air leakage before operating.. Note that for manifolds specified with other than double wiring, spare receptacle housings for expansion are not included unless indicated at the time of order.

17 Cassette Type Manifold Series SZ000 Dimensions/SZ000: Plug-in SSZ-60FD Stations U- - Note) The L to L dimensions for SSZ-60FD - Stations D- are the same as the SSZ-60FD - Stations U- dimensions. Scale: 7% n-one-touch fitting [With external pilot]. (Pitch) P= 0. (A, B ports) Applicable tube O.D.: ø ø6. 7. B B B B B R One-touch fitting (P, R ports) Applicable tube O.D.: ø n-m x 0. (A, B ports) -One-touch fitting (X, PE ports) Applicable tube O.D.: ø6 9 (.) B B B B B PE A A A A A P A A A A X P R A U Side. (L) Connector case Attachment lever (both sides) D Side Applicable connector: D-SUB Horizontal connector entry JIS-X-0 { MIL-C-0} Equivalent DIN rail 6 VDC +COM Manual override.7 In case of Locking type, turn after pushing in. A: Orange B: Green L (Rail mounting hole pitch.) L ( ) DIN rail holding screw Power supply terminals (M terminal screws) The indication ( marking is for VDC.). (With switch mounted) 7. (Station n)...(station ) Light/surge Side A: Orange Side B: Green. ON OFF ON OFF (.9) (7.) (DIN rail dimension) (.) 9. Switch (when equipped with switch) Internal pilot manifold L: Dimensions L n 6 7 L L L n: Stations External pilot manifold L: Dimensions L n 6 7 L L L n: Stations

18 Series SZ000 Dimensions/SZ000: Plug-in SSZ-60FD - Stations B- Scale: 7%. (Pitch) P= 0. -One-touch fitting (P, R ports) Applicable tube O.D.: ø [With external pilot]. A A A A A P R P B B B B B PE R A A A A X P A R P B B B B B R VDC +COM n-one-touch fitting (A,B ports) Applicable tube O.D.: ø ø6 -One-touch fitting (X,PE ports) Applicable tube O.D.: ø6. 6. (.) U Side (L) Connector case Attachment lever (both sides). 9 D Side Applicable connector: D-SUB Horizontal connector entry JIS-X-0 { MIL-C-0} Equivalent 0.. DIN rail Manual override In case of Locking type, turn after pushing in. A: Orange B: Green ( ) L (Rail mounting hole pitch.) L.7 DIN rail holding screw Power supply terminals (M terminal screws) The indication ( marking is for VDC.). (With switch mounted) 7. (Station n)...(station ) Light/surge Side A: Orange Side B: Green (.9). ON OFF ON OFF (7.) (DIN rail dimension) (.) 9. Internal pilot manifold L: Dimensions L n 6 7 L L L Switch (when equipped with switch) n: Stations External pilot manifold L: Dimensions L n 6 7 L L L n: Stations

19 Cassette Type Manifold Series SZ000 Dimensions/SZ000: Plug-in - SSZ-60PD Stations (6 pins) U- Note) The L to L dimensions for SSZ-60PD - Stations D- are the same as the SSZ-60PD - Stations U- dimensions. Scale: 7%. (Pitch) P=0. n-m x 0. (A, B ports) [With external pilot]. A A A A A P A A A A A P B B B B B R B B B B B R VDC +COM One-touch fitting (P, R ports) Applicable tube O.D.: ø -One-touch fitting (X, PE ports) Applicable tube O.D.: ø6 7.6 (.) X PE (L) n-one-touch fitting (A, B ports) Applicable tube O.D.: ø ø6 Applicable connector: 6 pin MIL type with strain relief (conforms to MIL-C-0) U Side. Connector case attachment lever (both sides) 6 Horizontal connector entry D Side. 6. Triangle mark DIN rail. Manual override In case of Locking type, turn after pushing in. ( ).7 A: Orange B: Green L (Rail mounting hole pitch.) L (Station n)...(station ) DIN rail holding screw Power supply terminals (M terminal screws) The indication ( marking is for VDC. ). (When switch is mounted) Applicable connector: 0 pin MIL type with strain relief (conforms to MIL-C-0) 7. Triangle mark location (for horizontal connector entry) Applicable connector: 0 pin MIL type with strain relief (conforms to MIL-C-0) Light/surge Side A: Orange Side B: Green. ON OFF ON OFF (.9) (7.) (DIN rail dimension) (.) 6. Triangle mark location Triangle mark location Switch (when equipped with switch) VDC +COM 60PG (0 pins) VDC +COM 60PH (0 pins) Note) Types 60PG and 60PH differ only in their connectors, and the L through L dimensions are the same as type 60P. Internal pilot manifold L: Dimensions L n 6 7 L L L n: Stations External pilot manifold L: Dimensions L n 6 7 L L L n: Stations

20 Series SZ000 Dimensions/SZ000: Plug-in SSZ-60PD - Stations B- (6 pins). (Pitch) P= 0. n-m x 0. (A, B ports) -One-touch fitting (P, R ports) Applicable tube O.D.: ø [With external pilot]. Scale: 7% P A A A A A X P P A A A A A P R B B B B B PE R R B B B B B R VDC +COM 7. (.) n-one-touch fitting (A, B ports) Applicable tube O.D.: ø ø6 Connector case attachment lever (both sides) One-touch fitting (X,PE ports) Applicable tube O.D.: ø (L) Applicable connector: 6 pin MIL type with strain relief (conforms to MIL-C-0) Horizontal connector entry U Side D Side 6. Triangle mark DIN rail. Manual override In case of Locking type, turn after pushing in. ( ) A: Orange B: Green.7 L (Rail mounting hole pitch.) L Power supply terminals (M terminal screws) The indication ( marking is for VDC.) (Station n)...(station ) Light/surge Side A: Orange Side B: Green Internal pilot manifold L: Dimensions L n 6 7 L L L ON OFF ON OFF (.9) (7.) (DIN rail dimension) (.) Switch (when equipped with switch) Triangle mark location DIN rail holding screw ( ). When equipped with Switch Applicable connector: 0 pin MIL type with strain relief (conforms to MIL-C-0) VDC +COM 60PG (0 pins) Triangle mark location (for horizontal connector entry) Triangle mark location Applicable connector: 0 pin MIL type with strain relief (conforms to MIL-C-0) VDC +COM. 7.. Triangle mark location 60PH (0 pins) Note) Types 60PG and 60PH differ only in their connectors, and the L through L dimensions are the same as type 60P n: Stations External pilot manifold L: Dimensions L n 6 7 L L L n: Stations

21 Non-plug-in manifold Port Solenoid Valve Series SZ000 Non-Plug-in Type How to Order SSZ 60 0 U Manifold stations 0 stations stations Supply/Exhaust block mounting position D D side ( to 0 stations) U U side ( to 0 stations) B Both sides ( to 0 stations) M Special specifications In the case of special specifications, indicate separately on a manifold specification sheet. Note) A total of up to supply/exhaust blocks can be mounted. Contact SMC if or more will be mounted. Options When a DIN rail is required that is longer than the standard types, specify the number of stations. Pilot specifications Nil Internal pilot specifications R External pilot specifications Solenoid valve (for non-plug-in manifold) SZ 60 M C6 Type of actuation position single solenoid position double solenoid position closed center position exhaust center position pressure center Pilot specifications Nil Internal pilot R External pilot Rated VDC 6 VDC V 6VDC S VDC R VDC Common specifications Nil N Pos. common Neg. common Manual override Nil: Non-locking push type A, B port size C ø One-touch fitting C6 ø6 One-touch fitting M M x 0. D: Push and turn locking type Screw driver operated M: With lead wire (length 00mm) MN: Without lead wire Electrical entry MO: Without connector B COM A B COM A NIL Nil Without light/surge NS With surge Z With light/surge

22 Series SZ000 How to Order Manifold Assemblies (Example) Example (SZ000, non-plug-in) Supply/exhaust block (U side mounting) Double solenoid (VDC) SZ60-M-C6 ( sets) Single solenoid (VDC) SZ0-M-C6 ( sets) U side D side Stations... SSZ-60-0U... set (manifold part number) SZ0-M-C6... sets (single solenoid part number) SZ60-M-C6... sets (double solenoid part number) The symbol indicates built-in. Put the symbol at the beginning of the part numbers for solenoid valves, etc. which are to be attached. The layout of valves starts with station on D side. Indicate the valves to be attached below the product part number, in order starting from station as shown in the drawing. When a layout becomes complicated, please indicate on a manifold specification sheet. (Manifold specifications sheets are on page 9.) Manifold specifications A, B port piping specifications Port size Valve effective area mm² (Cv value) Model Manifold type P(SUP), R(EXH) system Valve stations Weight W(g) Note ) C C6 M P A/B A/B R P A/B A/B R P A/B A/B R n : Number of supply/exhaust blocks m: Weight of DIN rail Location Direction P, EA, EB ports A/B ports SSZ-60 Non-plug-in type Common SUP, EXH to 0 stations Valve Lateral C C, C6, M. (0.9). (0.).7 (0.).9 (0.). (0.9). (0.) W = n + m + 9 Note ) In cases such as those where many valves are operated simultaneously, use type B (double side supply/exhaust), applying pressure to the P ports on both sides and exhausting from the R ports on both sides. Note ) The value is for manifold base mounting ( stations). position type with single action. Note ) The weight W is the value for the manifold only. To obtain the weight with solenoid valves attached, add the solenoid valve weights given on page for the appropriate number of stations. Refer to page 6 for the weight of DIN rails.

23 Cassette Type Manifold Series SZ000 Manifold Exploded View Type 60 (non-plug-in) manifold DIN rail holding screw U side e q t r w DIN rail holding screw D side y No. 6 Description Supply/exhaust block assembly End block assembly End block assembly Bushing assembly Bushing assembly DIN rail Part No. SZ000-0-A- C6 C SZ000--A SZ000--A SZ000--A SZ000--A VZ Note C6: With ø6 One-touch fitting C: With ø One-touch fitting For D side For U side Refer to page 6. Manifold Station Expansion Station expansion is possible at any position.. Loosen one DIN rail holding screw on either U side or D side.. Separate the blocks at the location where station expansion is desired.. Mount the valve on the DIN rail.. While pressing the manifold together from both sides, retighten the DIN rail holding screw of the end block assembly which was loosened. (tightening torque:.nm). Be sure to shut off the power and air supplies before disassembling. Since air may remain inside actuators, piping and manifolds, confirm that the air is completely exhausted before beginning work.. When disassembly and assembly are performed, air leakage may result if connections between blocks and tightening of the end block's holding screw, etc. are inadequate. Before supplying air, confirm that there are no gaps, etc. between blocks, and that manifold blocks are securely fastened to the DIN rail. Then, supply air and confirm that there is no air leakage before operating. 9

24 Series SZ000 Dimensions/SZ000: Non-plug-in SSZ-60- Stations U Scale: 7%. (Pitch) P= 0. n-one-touch fitting (A, B ports) Applicable tube O.D.: ø ø6. [With external pilot]. B B B B B PE R B B B B B R One-touch fitting (P, R ports) Applicable tube O.D.: ø P A A A A A -One-touch fitting (X, PE ports) Applicable tube O.D.: ø6 P A A X A A A (.) U Side (L). D Side.7 DIN rail... Light/surge Side A: Orange Side B: Green Manual override In case of Locking type, turn after pushing in. ( ) A: Orange B: Green L (Rail mounting hole pitch.) L (Station n)...(station ). (7.) (DIN rail dimension).7 6. DIN rail holding screw Approx. 00 Lead wire length.7 Internal pilot manifold L: Dimensions L n L L L n: Stations External pilot manifold L: Dimensions L n 6 7 L L L n: Stations

25 Cassette Type Manifold Series SZ000 Dimensions/SZ000: Non-plug-in SSZ-60 - Stations D Scale: 7%. (Pitch) P= 0.. -One-touch fitting (P, R ports) Applicable tube O.D.: ø. [With external pilot]. 6.7 R B B B B B B R B B B B B. A A A A A P n-one-touch fitting (A, B ports) Applicable tube O.D.: ø ø6 -One-touch fitting (X, PE ports) Applicable tube O.D.: ø6 A A A A A A P (.) U Side D Side (L). DIN rail Manual override In case of locking type, turn after pushing in. A: Orange B: Green ( ) L (Rail mounting hole pitch.) DIN rail holding screw Approx. 00 Lead wire length.7 L (Station n)...(station ) Light/surge Side A: Orange Side B: Green. (7.) (DIN rail dimension) Internal pilot manifold L: Dimensions L n 6 7 L L L n: Stations External pilot manifold L: Dimensions L n 6 7 L L L n: Stations

26 Series SZ000 Dimensions/SZ000: Non-plug-in SSZ-60- Stations B Scale: 7%. (Pitch) P= 0. -One-touch fitting (P, R ports) Applicable tube O.D.: ø. [With external pilot] R B B B B B PE R R B B B B B R. n-one-touch fitting (A, B ports) Applicable tube O.D.: ø ø6 P A A A A A P -One-touch fitting (X, PE ports) Applicable tube O.D.: ø6 P A A X A A A P (.) U side (L). D side.7 DIN rail. Light/surge Side A: Orange Side B: Green. Manual override In case of locking type, turn after pushing in. A: Orange B: Green ( ) L (Rail mounting hole pitch.) L (Station n)...(station ). (7.) 6. (DIN rail dimension).7 DIN rail holding screw Approx. 00 Lead wire length.7 Internal pilot manifold L: Dimensions L n 6 7 L L L n: Stations External pilot manifold L: Dimensions L n 6 7 L L L n: Stations

27 Type 60S Port Solenoid Valve Series SZ000 Serial Transmission Type How to Order SSZ 60S Q D 0 U Compatible equipment DeviceNet compatible: Q OMRON Corp. CompoBus/D compatible OMRON Corporation: R CompoBus/S ( points) compatible OMRON Corporation: R CompoBus/S ( points) compatible Mitsubishi Electric Corp.: V CC-Link compatible O Without SI unit SI unit mounting position D D Side This should be indicated even without SI unit. Options When a DIN rail is required that is longer than the standard types, specify the number of stations. Pilot specifications Nil R Internal pilot specifications External pilot specifications Supply/Exhaust block mounting position U U Side ( to 0 stations) D D Side ( to 0 stations) B Both sides ( to stations) M Special specifications In the case of special specifications, indicate separately on a manifold specification sheet. Note) A total of up to supply/exhaust blocks can be mounted. Contact SMC if or more will be mounted. Valve stations Symbol Stations 0 stations stations 0 stations stations Note Double wiring specifications Specified layout (up to solenoids possible) Note ) Double wiring specifications: Single, double and position solenoid valves can be used at all of the manifold stations. Note ) Specified layout: Indicate the wiring specifications on a manifold specification sheet. (Note that in locations where single solenoid wiring is indicated, it will be impossible to use double or position valves.)

28 ON OFF SMC Series SZ000 How to Order Manifold Assemblies (Example) Example (OMRON Corporation compatible serial unit) Supply/exhaust block assembly (U side mounting) Double solenoid (VDC) SZ60-LOZ-C6 ( sets) Single solenoid (VDC) SZ0-LOZ-C6 ( sets) Stations... U side D side Serial unit (D side mounting) SSZ-60SRID-0U-C6... set (manifold part number) SZ0-LOZ-C6... sets (single solenoid part number) SZ60-LOZ-C6... sets (double solenoid part number) The symbol indicates built-in. Put the symbol at the beginning of the part numbers for solenoid valves, etc. which are to be installed. The valve layout starts with station on D side. Indicate the valves to be installed below the product part number, in order starting from station as shown in the drawing. When a layout becomes complicated, please indicate on a manifold specification sheet. (Manifold specifications sheets are on pages 0.) How to Order Solenoid Valves SZ 60 LOZ C6 Type of actuation position single solenoid position double solenoid position closed center position exhaust center position pressure center Pilot specifications Nil Internal pilot R External pilot Manual override Nil: Non-locking push type A, B port size C ø One-touch fitting C6 ø6 One-touch fitting M M x 0. D: Push and turn locking type Screw driver operated Nil: Without switch Switch specifications J: With switch

29 ON ON Cassette Type Manifold Series SZ000 Specifications Specifications SI unit part numbers External power supply VDC±0% Symbol Specifications Part No. Current consumption (within unit) 0.A R, R, V, Q Q R DeviceNet compatible: OMRON Corp. CompoBus/D compatible OMRON Corporation: CompoBus/S ( points) compatible EX0-SDN EX0-SCS R OMRON Corporation: CompoBus/S ( points) compatible EX0-SCS V Mistubishi Electric Corporation: CC-Link compatible EX0-SMJ Type SQ DeviceNet compatible Type SR/SR OMRON Corporation CompoBus/S compatible Type SV Mitsubishi Electric Corporation CC-Link compatible Terminal block/led description PWR MOD/NET V OV V- CAM FG CAM Vt SETTINGS LED name Content PWR Green light turns on when line power is input Light off: When unit is off-line or power is turned off MOD/ NET Continuous green light: When unit is on-line and also in operation Flashing red light: When a recoverable transmission error is occurring Continuous red light: When a nonrecoverable transmission error occurs or on-line status cannot be achieved LED name PWR COMM ERR PWRCOM ERR ADDRESS NO. BS+ BDH BDL BS- FG V 0V Content Turns on during supply of communication power, turns off when there is no input Turns on during normal communication, turns off during communication error or standby Turns on when communication error occurs, turns off during normal communication or standby PWR L RUN L ERR.SD RD B RATE STATION NO. V 0V +V G DA DB DG FG LED name Content Turns on during supply of communication PWR power, turns off when there is no input L RUN Turns on with receipt of normal data SD Turns on with data communication RD Turns on with received data Turns on with transmission/setting error, L ERR. flashes when code or transmission speed setting changes during operation DeviceNet CompoBus/S system CC-Link system OMRON Corporation CompoBus/D system Master unit: Type C00HW-SRM Master unit: AJ6BT Master unit: Type C00HW-DRM Master unit: Type CQM-SRM Master unit: ASJ6BT output points Master unit: AJ6QBT Note output points (type SR) output points (type SR) Master unit: ASJ6QT output points Terminating resistor V 0V V- CANL FG CANH V+ V 0V V- CANL FG CANH V+ BS+ BDH BDL BS- V 0V BS+ BDH BDL BS- V 0V Cable wiring V- CANL FG CANH V+ Master BDH BDL Connector with terminating resistance Crimped connectors for junction Master unit SI unit SI unit DA DB DG Terminating resistor DA DB DG DA DB DG SLD FG FG FG Class ground Class ground Class ground Twisted pair with shielding

30 Series SZ000 Dimensions/SZ000: Serial Transmission Type SSZ-60S D- Stations U Note) The L to L dimensions for SSZ-60S D - Stations SSZ-60S D- Stations U dimensions. D are the same as the Scale: 7% [With external pilot]. -One-touch fitting (X, PE ports) Applicable tube O.D.: ø (Pitch) P= 0. n-one-touch fitting (A, B ports) Applicable tube O.D.: ø ø6 (.) (L). A A A A A. 6.. B B B B B B B R A A A A A X P B B B B B PE R One-touch fitting (P, R ports) Applicable tube O.D.: ø A A A A A P n-m x 0. (A, B ports) U Side D Side DIN rail DIN rail holding screw Light/surge Side A: Orange Side B: Green Manual override In case of locking type, turn after pushing in. A: Orange B: Green ( ) L (Rail mounting hole pitch.) L (Station n)...(station ). (When equipped with switch). (7.) (DIN rail dimension) ON OFF ON OFF Switch (when equipped with switch) Internal pilot manifold L: Dimensions L n L L L n: Stations External pilot manifold L: Dimensions L n L L L n: Stations

31 Cassette Type Manifold Series SZ000 Dimensions/SZ000: Serial Transmission Type SSZ-60S D- Stations B [With external pilot] Scale: 7%. -One-touch fitting (X,PE ports) Applicable tube O.D.: ø6 n-one-touch fitting (A, B ports) Applicable tube O.D.: ø ø6 (.)... (When equipped with switch) (Pitch) P= 0. A A A A X P A P R B B B B B R R B B B B B PE R -One-touch fitting (P, R ports) Applicable tube O.D.: ø A A A A A P P n-m x 0. (A, B ports) U Side (L) D Side DIN rail DIN rail holding screw Light/surge Side A: Orange Side B: Green Manual override In case of locking type, ( turn after pushing in. ) A: Orange B: Green L (Rail mounting hole pitch.) L (Station n)...(station ). (7.) (DIN rail dimension) ON OFF ON OFF Switch (when equipped with switch) Internal pilot manifold L: Dimensions L n L L L n: Stations External pilot manifold L: Dimensions L n L L L n: Stations. 97. L n 9 L L L L n 9 L L L

32 Please copy this page for use without removing it. SZ000: Cassette Type Plug-in manifold Manifold Valve Specification Sheet Make entries in order from () to (). q How to Order Manifolds Enter the symbols for the required specifications in the blanks below. SSZ-60 D Connector type Symbol Connector type F D-sub connector, pins P Flat cable connector, 6 pins PG Flat cable connector, 0 pins PH Flat cable connector, 0 pins Connector entry direction Mounting Symbol position Vertical Horizontal The possible number of valve stations (number of solenoids) is limited depending on the connector type and the presence or absence of power supply terminals. Referring to catalog pages &, make selections so that the maximum number of stations is not exceeded. w How to Order Valves Valve stations Symbol Stations 0 stations stations Enter the symbols for the required specifications in the blanks below. SZ 60 LOZ Company name Contact Specification sheet No. Order No. Equipment name Quantity Supply/exhaust block assembly mounting position Symbol U D B Mounting position U side D side Both sides Applicable stations to 0 stations to 0 stations to 0 stations M Special specifications In case of special specifications, indicate in the station table below. Nil Non-locking push type A B C D E F D Push & turn locking type, screw driver operated Type of valve actuation A Pilot system B Rated C COM specifications F A, B port size position single solenoid Nil Internal pilot VDC Nil Positive common C ø One-touch fitting position double solenoid R External pilot 6 VDC N Negative common C6 ø6 One-touch fitting position closed center When an external pilot valve Match to the Match to the common M M x 0. position exhaust center is to be used, enter a specifications of the specifications of the manifold. M Mixed symbol in section (b) of the manifold. position pressure center station table below. Note) In case of mixed port sizes, Indicate in the station table below. indicate by entering C, C6 and M as required in section (a) of the station table below. e Station Table Enter the ordered part numbers. Section below for SMC use only D Switch specifications Set(s) Date required Part No. Quantity Part No. Quantity Order No. E Nil J Manual override Pilot port blocking disk: SZ000--A Supply/exhaust block assembly (ø): SZ000-0-A-C Power supply terminal specifications Nil P P N N Clerk (code No.) Branch code Date / / Options When a DIN rail is required that is longer than the standard types, specify the number of stations. (Max. 0 stations) Pilot system Symbol Specifications Standard/internal Nil pilot specifications R External pilot specifications Without switch With switch None VDC Pos. common VDC VDC Neg. common VDC Indicate the layout of valves, etc. with symbols. When the sizes of ports A and B are mixed, indicate in section (a) with C, C6 and M. When the port size of the supply/exhaust block assembly is ø6, indicate with C6 in section (c). (It will be ø when indicated with a symbol.) When the port size of the external pilot block assembly is ø, indicate with C in section (c). (It will be ø6 when indicated with a symbol.) Valve stations or layout Quantity Single solenoid position Double solenoid Closed center a position Exhaust center Pressure center External pilot specifications b (enter only in case of external pilot) Note ) Enter for Supply/exhaust block assembly c special specs. External pilot block assembly SUP blocking disk d EXH blocking disk Note ) Pilot port blocking disk Wiring Single wiring e specifications Double wiring Enter only when specifying wiring. extra stations can be specified for station expansion. However, this will be less than the maximum number of solenoids. Note ) The number of supply/exhaust block assemblies and pilot block assemblies should each be or less. Contact SMC in case or more will be installed. Note ) Enter only when internal pilots and external pilots will be mixed on the same manifold. [Note] SUP blocking disk: SZ000--A EXH blocking disk: SZ000--A (pcs./location) Blanking block assembly : SZ000--A U side n m wq ewq Supply/exhaust block assembly (ø6): SZ000-0-A-C6 External pilot block assembly (ø6): SZ000--A-C6 External pilot block assembly (ø): SZ000--A-C Valve stations Layout (for special specifications) Connector D side Note) When there are special specifications for the mounting position of the supply/exhaust block assembly, enter the part number and quantity for the supply/exhaust block assembly together with the manifold type.