5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in. Flow characteristics (1) 1 4/2 (P A/B) 4/2 5/3 (A/B R1/R2)

Transcription

1 For details about certified products conforming to international standards, visit us at 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Model position 3 position Type of actuation Single Double Closed center Exhaust center Pressure center Double check Plug-in VFS400 VFS400 VFS4300 VFS4400 VFS4500 VFS4600 Model Non plug-in VFS40 VFS40 VFS430 VFS440 VFS450 VFS460 Note ) Based on JIS B 8375 (once per 30 days) for the minimum operating frequency. Note ) Based on JIS B (The value at supply press. 0.5 MPa). Note 3) The figures in the above list are for without sub-plate. In the case of with plug-in sub-plate and with non plug-in sub-plate, add 0.50 kg and 0.43 kg respectively. Note 4) Note ) and Note ) are with controlled clean air. Compact yet provides a large flow capacity /: C: dm 3 /(s bar) Low power consumption:.8 W DC Easy maintenance types of sub-plates: Plug-in and non plug-in JIS position Single Double 3 position Closed center Exhaust center Pressure center Double check Port size Flow characteristics () 4/ (P A/B) 4/ 5/3 (A/B R/R) C C [dm 3 /(s bar)] b Cv [dm 3 /(s bar)] b Cv Standard Specifications Valve specifications Electricity specifications Option Specifications Pilot type Manual override Fluid Maximum operating pressure position Minimum operating pressure 3 position Proof pressure Ambient and fluid temperature Lubrication Pilot valve manual override Shock/Vibration resistance Enclosure Coil rated voltage Allowable voltage fluctuation Coil insulation type Apparent power (Power consumption) AC Power consumption DC Electrical entry Inrush Holding ,000, or less 5 or less 50 or less 50 or less 50 or less or less.7 Air/Inert gas.0 MPa 0. MPa 0.5 MPa.5 MPa 0 to 60 C () Non-lube () Non-locking push type (Flush) 50/50 m/s (3) Type E: Dustproof (level 0), Type F: Dripproof (level ), Type D: Splashproof (level 4) (4) 00, 00 VAC, 50/60 Hz; 4 VDC 5 to +0% of rated voltage Class B or equivalent (30 C) (5) 5.6 VA/50 Hz, 5.0 VA/60 Hz 3.4 VA (. W)/50 Hz,.3 VA (.5 W)/60 Hz.8 W (.04 W: With light/surge voltage suppressor) Conduit terminal Grommet terminal, DIN terminal Note ) Use dry air at low temperatures. Note ) Use turbine oil Class (ISO VG3), if lubricated. Note 3) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Note 4) Based on JIS C 090. Note 5) Based on JIS C 40. Main valve Pilot valve Coil rated voltage Porting specifications Option External pilot Note) Direct manual override Non-locking push type (Extended), Locking type (Tool required), Locking type (Lever) 0 to 0, 0, 40 VAC, 50/60 Hz, 00 VDC Bottom ported With light/surge voltage suppressor, Non-rotating DIN terminal Note) Operating pressure: 0 to.0 MPa Pilot pressure position: 0. to.0 MPa, 3 position: 0.5 to.0 MPa () Max. operating cycle (cpm) () Response time (ms) (3)(4) Weight (kg) VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN

2 Body type O: sub-plate Electrical entry F: conduit terminal Plug-in VFS How to Order F Porting specifications Nil B Side ported Bottom ported In the case of external pilot (Option), bottom piping is not available. Port size Nil Without sub-plate EA, EB: 3 8 Thread type Nil N T F NPT NPTF G Non plug-in VFS4 0 E position single 5 3 position pressure center Option Nil Z P Electrical entry None With light/surge voltage suppressor Non-rotating DIN terminal In the case of w/ Z, enter ZP. Type P is available for DIN type only. E: Grommet terminal D: DIN terminal Pilot valve Manual override Nil: Non-locking push type (Flush) A : Non-locking push type (Extended) position double 3 position double check position closed center 3 position exhaust center Reverse pressure: Can be used by external pilot specifications. Body type : sub-plate Pilot type Nil R Coil rated voltage Internal pilot External pilot 00 VAC, 50/60 Hz 00 VAC, 50/60 Hz 0 to 0 VAC, 50/60 Hz 0 VAC, 50/60 Hz 4 VDC VDC 40 VAC, 50/60 Hz 9 Other B : Locking type (Tool required) C : Locking type (Lever) How to Order Pilot Valve Assembly SF4 F 30 Body option 0 Standard Direct manual override Coil rated voltage 00 VAC, 50/60 Hz 00 VAC, 50/60 Hz 3 0 to 0 VAC, 50/60 Hz 4 0 VAC, 50/60 Hz 5 4 VDC 6 VDC 7 40 VAC, 50/60 Hz 9 Other Refer to page for voltage conversion. Nil Manual override A B C Non-locking push type (Flush) Non-locking push type (Extended) Locking type (Tool required) Locking type (Lever)

3 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Cylinder Speed Chart System Solenoid valve A B System A B 3 8 Average speed (mm/s) System Components Speed controller AS40- (S = 73 mm ) AS40-04 (S = 97 mm ) Silencer AN300- (S = 60 mm ) AN (S = 90 mm ) SGP (Steel pipe) Port size x Length 0A x 5A x Use as a guide for selection. Please confirm the actual conditions with SMC Sizing Program. Bore size Series CA Pressure 0.5 MPa Note) The CA series Series CS has been changed Pressure 0.5 MPa Load factor 50% Stroke 500 mm to the CA series. Load factor 50% Cylinder stroke 000 mm ø50 ø63 ø80 ø00 ø5 ø40 ø60 ø80 ø00 ø50 ø300 Perpendicular, upward actuation Horizontal actuation It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open. The average velocity of the cylinder is what the stroke is divided by the total stroke time. Load factor: ((Load weight x 9.8)/Theoretical force) x 00% VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Double Check Spacer/Specifications Specifications Can hold an intermediate cylinder position for an extended time If the double check spacer with a built-in double check valve is combined, it will enable the cylinder to stop in the intermediate stroke and maintain its position for a long time without being affected by the leakage between the spools. Double check spacer Double check spacer part no. Applicable valve model Leakage (cm 3 /min) VVFS4000-A- VFS4400- F Solenoid one side energized Solenoid both sides de-energized Supply pressure: 0.5 MPa Caution VVFS4000-A- VFS440- D VFS440- E In the case of 3 position double check valve (VFS46 0), check the leakage from piping and fittings in between valve and cylinder by means of synthetic detergent solutions, and ensure that there is no such leakage found there. Also check the leakage from cylinder seal and piston seal. If there is any leakage, sometimes the cylinder, when valve is de-energized, can move without stopping at intermediate position. Be aware that if the exhaust side is restricted excessively, the intermediate stopping accuracy will decrease and will lead to improper intermediate stops. P P A B EA 30 EB or less EA 30 EB or less EA 0 EB Check Valve Operation SUP side pressure P (MPa) Piston Cylinder side pressure (P) Operating range Check valve SUP side pressure (P) Cylinder side pressure P (MPa) The combination of VFS4 0 0, VFS4 0 0 and Double check spacer for prevention of falling at the stroke end but cannot hold the intermediate position of the cylinder

4 Construction position single position double 3 position closed center/exhaust center/pressure center Closed center Exhaust center Pressure center Component Parts No. Description q Body w Sub-plate e Spool/Sleeve r Adapter plate t End plate y Piston u Junction cover i Light cover Material Aluminum die-casted Aluminum die-casted Stainless steel Aluminum die-casted Aluminum die-casted Resin Resin Resin Note Platinum silver Platinum silver Black Black Sub-plate Assembly Part No. Plug-in VFS4000-P- 04 Non plug-in VFS4000-S- 04 Mounting bolt and gasket are not included. Part no. for mounting bolt and gasket BG-VFS4000 Replacement Parts No. Description Material Part no. VFS4 VFS4 VFS43 /44 /45 o!0 Return spring Gasket Stainless steel NBR VF VF VF VF A VF ! Hexagon socket head screw Steel M4 x 40 M4 x 40 M4 x 40! Detent assembly VF4000-A!3 Pilot valve assembly Refer to How to Order Pilot Valve Assembly on page

5 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Plug-in position single/double, 3 position closed center/exhaust center/pressure center/double check position single: VFS400- F -ø6.5 mounting hole /8 external pilot port (Only for external pilot) (B), 4(A) port 8 (PE port) VK Pilot valve manual override (With direct manual override) With light/surge voltage suppressor 07 (FZ) VZ VF VFR VP4 VZS G Electrical entry 5-3 8, (R, R: 3 8 ) VFS VS4 VQ7 EVS -ø6.5 mounting hole VFN 5-3 8, (R, R: 3 8 ) Bottom ported position double: VFS400- F 3 position closed center: VFS4300- F 3 position exhaust center: VFS4400- F 3 position pressure center: VFS4500- F 3 position double check: VFS4600- F -ø6.5 mounting hole 87 (3 position: 96.5) -ø6.5 mounting hole With light/surge voltage suppressor Light window Pilot valve manual override With light/surge voltage suppressor Light window 07 (FZ) (With direct manual override) Pilot valve manual override With direct manual override G Electrical entry 5-3 8, (R, R: 3 8 ) G Electrical entry 5-3 8, (R, R: 3 8 )

6 Non Plug-in position single/double, 3 position closed center/exhaust center/pressure center/double check position single: VFS40- E, VFS40- D -ø6.5 mounting hole (B), 4(A) port - 8 (PE port) Applicable cabtire cable O.D. ø8 to ø0 Pilot valve manual override G DIN terminal (With direct manual override) 08 (E, EZ) 38.5 (D, DZ) 50.5 (D, DZ) 5-3 8, (R, R: 3 8 ) 5-3 8, (R, R: 3 8 ) Bottom ported -ø6.5 mounting hole position double: VFS40- E, VFS40- D 3 position closed center: VFS430- E, VFS430- D 3 position exhaust center: VFS440- E, VFS440- D 3 position pressure center: VFS450- E, VFS450- D 3 position double check: VFS460- E, VFS460- D -ø6.5 mounting hole 87 (3 position: 96.5) -ø6.5 mounting hole G DIN terminal Applicable cabtire cable O.D. ø8 to ø0 Pilot valve manual override (With direct manual override) G / DIN terminal 08 (E, EZ) 38.5 (D, DZ) 50.5 (D, DZ) Applicable cabtire cable O.D. ø8 to ø0 Pilot valve manual override 77 (E, EZ) With direct manual overide 08.5 (D, DZ) 0.5 (D, DZ) 5-3 8, 5-3 8, (R, R: 3 8 ) (R, R: 3 8 )

7 Specifications Plug-in Type: With Terminal Block Since lead wires of solenoid valve are connected with the terminals on upper surface of terminal block, corresponding lead wires from power source can be wired at the bottom of terminal block. Terminal block Plug-in Type: With Multi-connector Master connection of power and solenoid valves. Quick wiring permits easier installation. Multi-connector Plug assembly (Option) Refer to page VV5FS4 0T 06 Thread type Port size Nil 0 stations P, R, R A, B N NPT 3 8 T NPTF with terminal block 0 0 stations 04 F G M Mixed For bottom ported, Passage Porting 3 8 is only available. specifications P R, R (A, B) Side Common Common Bottom VV5FS4 with multi-connector Connector mounting direction D U mounting mounting 0C D 0 (Wiring specifications: Refer to page ) 08 8 stations Max. 8 stations Passage P R, R Side Common Common Bottom 05 stations Porting specifications (A, B) Thread type Port size P, R, R A, B Nil N NPT 3 8 T NPTF 04 F G M Mixed For bottom ported, 3 8 is only available. VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Plug-in Type With: D-sub Connector Wide range of interchangeability (MIL Spec DIN connector terminal VV5FS4 5 pcs attached.) Quick wiring permits easier installation. with D-sub connector Connector mounting direction D-sub connector Plug assembly (Option) Refer to page D U (Wiring specifications: Refer to page ) mounting mounting 0F D 06 Thread type Port size Nil 0 stations P, R, R A, B N NPT T 8 stations NPTF 04 F G Max. 8 stations M Mixed For bottom ported, Passage Porting 3 8 is only available. specifications P R, R (A, B) Side Common Common Bottom Non Plug-in Type: Grommet Terminal, DIN Terminal Wiring for every valve. Grommet terminal DIN terminal VV5FS Port size 0 stations P, R, R A, B stations 04 M Mixed Passage Porting For bottom ported, specifications 3 8 is only available. P R, R (A, B) Side Common Common Bottom Thread type Nil N NPT T NPTF F G

8 How to Order Assembly Please indicate manifold base type, corresponding valve, and option parts. <Example> with terminal block: 6 stations ( base) VV5FS4-0T-06- ( position single) VFS400-5FZ 3 ( position double) VFS400-5FZ (Blanking plate) VVFS4000-0A : 6 stations ( base) VV5FS ( position single) VFS40-5D 5 (3 position exhaust center) VFS440-5D (Individual EXH spacer) VVFS4000-R-04- Specifications Base model VV5FS4-0 VV5FS4-0 Flow Characteristics at the Number of (Operated individually) Model VV5FS4 Wiring With terminal block With multi-connector With D-sub connector DIN terminal Grommet terminal Porting specifications A, B port Side/ Bottom With multi-connector, or with D-sub connector: 8 stations max. Port size: / Port size P, EA, EB A, B 3 8, to 0 Applicable valve model VFS4 00- F VFS4 0- D VFS4 0- E Passage/ Station Station 5 Station 0 C [dm 3 /(s bar)] b Cv C [dm 3 /(s bar)] b Cv / (P A/B) 4/ 5/3 (A/B R/R) Option Parts Assembly Individual SUP spacer An individual SUP spacer set on manifold block can form SUP port for every valve. Body type Part no. VVFS4000-P-- VVFS4000-P-- Throttle valve spacer Needle valve set on the manifold block can control cylinder speed by throttling exhaust. Body type Part no. VVFS4000-0A- VVFS4000-0A- Option With exhaust cleaner /Non Valve exhaust noise dampening: 35 db or more. Oil mist collection: Rate of collection 99.9% or more. Piping process reduced. Individual EXH spacer An individual EXH spacer set on manifold block can form EXH port for every valve. (common EXH type) Body type Part no. VVFS4000-R-04- VVFS4000-R-04- SUP block disk When supplying manifold with more than two different pressures, high and low, insert a block disk in between stations subjected to Plug-in different pressures. Body type Part no. AXT634-0A EXH block disk When valve exhaust affects the other stations on the circuit or when a reverse pressure valve is used to a standard manifold valve, insert EXH block disk in between stations to separate valve exhaust. Body type Part no. AXT634-A Double check spacer If the double check spacer with a built-in double check valve is combined, it will enable the cylinder to stop in the intermediate stroke and maintain its position for a long time without being affected by the leakage between the spools. Body type Part no. VVFS4000-A- VVFS4000-A- Interface regulator Interface regulator set on manifold block can regulate the pressure to each valve. (Refer to page for Flow Characteristics.) Body type P port regulation ARBF P- ARBF P- A reduced pressure ARBF A- ARBF A- B reduced pressure ARBF B- ARBF B- For details, refer to page With control unit /Non Filter, regulation valve, pressure switch and air release valve are all combined to form one unit. Piping processes are eliminated. For details, refer to page With serial interface unit for serial transmission Solenoid valve wiring process reduced considerably. Disperse installation possible. solenoid valve: 8 stations max. 3 positions (5 solenoids). Maintenance and inspection are easy. EXH block disk SUP block disk Blanking plate It is used by attaching on the manifold block for being prepared for removing a valve for maintenance reasons or planning to mount a spare valve, etc Body type Part no. VVFS4000-0A For details, refer to Serial Transmission catalog separately.

9 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in, (With terminal block): VV5FS4-0T- Station - Port size n- 3 8 Pilot valve manual override VK VZ VF Light n- 3 8, VFR VP4 Bottom ported: VV5FS4-0T- Station - Port size - 8 (Pilot EXH port: PE) -G 4 Electrical entry - 8 (External pilot port) VZS VFS VS4 VQ7 Formula for manifold weight M = 0.565n (kg) n: 6- EVS VFN : VV5FS4-0- Station - Port size n- 3 8 Pilot valve manual override Light n- 3 8, Bottom ported: VV5FS4-0- Station - Port size G Cable ø8 to ø0-8 (Pilot EXH port: PE) - 8 (External pilot port) L Formula for manifold weight M = 0.478n (kg) L L n: Formula L = 43 x n + 70 L = 43 x n /

10 with multi-connector/d-sub connector with multi-connector: VV5FS4-0CD- Station - Port size, VV5FS4-0CU- Station - Port size n- 3 8 Pilot valve manual override Light n- 3 8, Bottom ported: CD VV5FS4-0 - Station - Port size CU Plug assembly VVFS000-30A- (Option: Refer to page ) - 8 (Pilot EXH port: PE) - 8 (External pilot port) Formula for manifold weight M = 0.57n +.0 (kg) n: Station Wiring specifications: Refer to page with D-sub connector: VV5FS4-0FD- Station - Port size, VV5FS4-0FU- Station - Port size n- 3 8 Pilot valve manual override Light n- 3 8, Bottom ported: FD VV5FS4-0 - Station - Port size FU Formula for manifold weight M = 0.57n (kg) Wiring specifications: Refer to page Plug assembly VVZS3000-A- (Option: Refer to page ) - 8 (External pilot port) L L L n: Formula L = 43 x n + 70 L = 43 x n (Pilot EXH port: PE)

11 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in with Exhaust Cleaner Serves to protect working environment. Valve exhaust noise dampening: 35 db or more. Collection rate of drainage and oil mist: 99.9% or more. Piping work is reduced. Exhaust cleaner (Option) Exhaust cleaner (Option) Caution When using an exhaust cleaner, mount it downwards. Refer to Best Pneumatics Vol. 5 for Exhaust Cleaner details. Specifications Wiring : VV5FS4-0 With terminal block With multi-connector With D-sub connector VFS4 00- F : VV5FS4-0 DIN terminal Grommet terminal Applicable valve model VFS4 0- D, VFS4 0- E Common SUP/Common EXH Porting specifications (B), 4(A) port Side: 3/8, /, Bottom: 3/8 (Option) (P), 3(R), 5(R) port P: /, EXH:, / to 0 () Applicable exhaust cleaners AMC60-0 (Connecting port size R ), AMC80-4 (Connecting port size R /) () Note ) With multi-connector, or with D-sub connector: 8 stations max. Note ) of 5 or more and high frequency of operation should be used with AMC80-4. Exhaust cleaners AMC60-0 and AMC80-4 are not attached. VV5FS4 Base type/electrical entry 0T with terminal block 0C with multi-connector 0F with D-sub connector 0 Connector mounting direction With connector Applicable base Nil None 0T, 0 D mounting 0C, 0F U mounting 0 06 CD 0 stations 0 0 stations Base type 0T, 0: to 0 stations Base type 0C, 0F: to 8 stations <Example> with terminal block (6 stations) ( base) VV5FS4-0T-06--CD ( position single) VFS400-5FZ ( position double) VFS400-5FZ (Blanking plate) VVFS4000-0A (Exhaust cleaner) AMC60-0 (6 stations) ( base) ( position single) ( position double) (Blanking plate) (Exhaust cleaner) How to Order VV5FS CU VFS40-5E VFS40-5E VVFS4000-0A AMC80-4 Please indicate manifold base type, corresponding valve, and option parts. 3 3 Nil N T F Port size P 04 M Exhaust cleaner mounting direction CD CU NPT NPTF G mounting mounting Please indicate exhaust cleaner size or port size. Thread type A, B 3 8 Mixed For bottom ported, 3 8 is only available. Exhaust Exhaust cleaner mounting direction Passage Porting specifications P R, R (A, B) Side Common Common Bottom VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN

12 with Exhaust Cleaner, : VV5FS4-0T- Station - Port size - CD CU Pilot valve manual override R, 6.5 ( 60) Exhaust cleaner (Option) n- 3 8, Manual override mounting - 8 (Pilot EXH port: PE) -G 4 Electrical entry - 8 (External pilot port) - mounting ( ): AMC80 : VV5FS4-0- Station - Port size - CD CU Pilot valve manual override R, n- 3 8, Manual override 6.5 ( 60) Exhaust cleaner (Option) mounting - 8 (Pilot EXH port: PE) - 8 (External pilot port) mounting ( ): AMC80 - L L L n: Formula L = 43 x n + 70 L = 43 x n

13 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in with Control Unit Control unit (Filter, Regulator, Pressure switch, Air release valve) are all standardized to the one unit, and can be mounted on the manifold base without any attachments. Piping processes are eliminated. Control Unit Specifications Air filter (With auto-drain/with manual drain) Filtration degree 5 µm Regulator Set pressure (Outlet pressure) 0.05 to 0.85 MPa Pressure switch () Set pressure range: OFF 0. to 0.6 MPa Differential 0.08 MPa or less Contact a Indicator light LED (RED) Max. switch capacity VA AC, W DC 4 VAC/DC or less: 50 ma Max. operating current 48 VAC/DC: 40 ma 00 VAC/DC: 0 ma Air release valve (Single only) Operating pressure range 0. to.0 MPa VV5FS4 0C D 08 AP Base type/electrical entry 0T with terminal block Control Unit/Option Air release () valve spacer Pressure switch Blanking plate Filter element <> VVFS4000-4A-R ( mounting) <> VVFS4000-4A-R ( mounting) IS000P-- Filter regulator Pressure switch Release valve 04-5B MP-3 MP3- VVFS4000-4A-0 Note ) Voltage: 4 VDC to 00 VAC Inner voltage drop: 4 V Note ) Combination of a valve VFS4 (single) and a release valve spacer can be used as an air release valve. Note 3) The non plug-in type cannot be mounted afterwards. Air release valve coil rating Nil None (F, G type only) 00 VAC, 50/60 Hz 5 4 VDC 9 Other 0C with multi-connector Control unit type 0F with D-sub connector 0 Nil A AP M MP F Control equipment Connector mounting direction Air filter with auto-drain G C E With connector Applicable base Air filter with manual drain Nil None 0T, 0 Regulator D mounting Air release valve 0C, 0F U mounting Pressure switch Blanking plate (Air release valve) 0 stations Blanking plate (Filter, Regulator) Blanking plate (Pressure switch) 0 Passage Porting 0 stations specifications Number of manifold blocks P R, R (A, B) required for mounting (stations) Side Common Common Bottom Base type 0T, 0: to 0 stations Base type 0C, 0F: to 8 stations Caution When using an air filter with auto-drain or manual drain, mount the filter vertically. Port size P, R, R A, B 04 M Mixed For bottom ported, 3 8 is only available. Specifications Wiring Applicable valve model Porting specifications How to Order Thread type 3 8 Nil N T F NPT NPTF G : VV5FS4-0 With terminal block With multi-connector With D-sub connector VFS4 00- F (B), 4(A) port (P), 3(R), 5(R) port With multi-connector, or with D-sub connector: 8 stations max. Please indicate manifold base type, corresponding valve, and option parts. <Example> with terminal block: In order to mount control unit, it requires stations. ( base) ( position single) ( position double) VV5FS4-0T-08--AP5 VFS400-5FZ VFS400-5FZ 4 : In order to mount control unit, it requires stations. ( base) ( position single) (3) : VV5FS4-0 DIN terminal Grommet terminal VFS4 0- D, VFS4 0- E Common SUP, Common EXH Side: 3/8, /, Bottom: 3/8 Side: / to 0 VV5FS A VFS40-5D 4 VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN 3-8-8

14 with Control Unit, : VV5FS4-0T- Station - Port size -AP Voltage for release valve Example for manifold Individual EXH spacer Pilot valve manual override Pilot valve manual override n-, 3 8 Double check spacer Individual SUP spacer (80.5: -MP) Pressure switch Air release valve Air release valve Air filter regulator Outlet for check Control unit Pressure switch 05-8 Pilot EXH port: PE -G /4 Electrical entry 3/4 (Po port) (External pilot port) 6- : VV5FS4-0- Station - Port size -AP Voltage for release valve Example for manifold Individual EXH spacer n- 3 8, Pilot valve manual override Double check spacer Individual SUP spacer (80.5: -MP) Pressure switch Air release valve Air release valve Air filter regulator Pressure switch Outlet for check 05 Control unit - 8 Pilot EXH port: PE 6-3/4 (Po port) (External pilot port) L L L L3 (MP) L3 (AP) n: Formula L = 43 x n L = 43 x n L3 = 43 x n L3 = 43 x n

15 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Option Parts Individual SUP spacer: VVFS4000-P-- () VVFS4000-P-- (), Double check spacer: VVFS4000-A- () VVFS4000-A- () (7: With direct manual override) Individual EXH spacer: VVFS4000-R-04- () VVFS4000-R-04- () (79: With direct manual override) Individual SUP spacer Individual EXH spacer SUP block disk: AXT634-0A EXH block disk: AXT634-A Interface regulator/p port regulation: ARBF P- () ARBF P- () (95: With direct manual override) Interface regulator Double check spacer Interface regulator/a port regulation: ARBF A- () ARBF A- () VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Block disk mounting position ( ): EXH block disk (95: With direct manual override) Interface regulator Throttle valve spacer: VVFS4000-0A- () VVFS4000-0A- () Interface regulator/b port regulation: ARBF B- () ARBF B- () (7: With direct manual override) Throttle valve spacer (95: With direct manual override) Interface regulator

16 Base Construction, Non End plate () block End plate () Replacement Parts No. q w e r t y u i o!3 Description Connection fitting A Connection fitting B Gasket Gasket Gasket O-ring O-ring Terminal assembly Junction cover assembly Rubber plug Material Steel plate Steel plate NBR NBR NBR NBR NBR For 0T For 0SU NBR Replacement Parts: Sub Assembly Part no. VVF A VVF VVF (End plate) VVF ( block) VVF AS568-0 P-3 VVF4000-6A VVF4000-4A- AZ738-30A- AXT336-9 For increasing the manifold bases, please order the manifold block assembly number of the principal part assembly!0. For plug-in type: The manifold base with terminal stand (integrated with a junction cover) is required with the o junction cover assembly. Note) Base/Construction: with terminal block. No. Description Assembly part no. Component parts Applicable manifold base!0!! block VVF4000-A-- block!0, Terminal i, Metal joint q, w, 04 Gasket r, Receptacle assembly assembly VVF4000-A-- block!0, Metal joint q, w, Gasket r 04 End plate (D)!, Metal joint q, w, Gasket e, t, VVF4000-3A- End plate () O-ring y, u assembly End plate (D)!, Metal joint q, w, Gasket e, t, VVF4000-3A- O-ring t, y End plate () assembly VVF4000-A- VVF4000-A- End plate (U)!, Metal joint q, w End plate (U)!, Metal joint q, w

17 .7 S OLENOID VALVES S ERIES NVFS M O D E L NVFS4000 S Y M B O L S Position Number Of Type Port Size Cv Response Solenoid Plug-In (NPTF) Factor Time (ms) Single NVFS400 3/ or less Position / 6 Double NVFS400 3/ or less / 3.6 Closed NVFS4300 3/ or less Center / 3 Exhaust NVFS4400 3/ or less 3 Position Center / 3 Pressure NVFS4500 3/ or less Center / 3.4 Perfect NVFS4600 3/ or less (Double Check) /.8 T ECHNICAL SPECIFICATIONS S T ANDARD T ECHNICAL SPECIFICATIONS O PTIONAL Fluid Max Operating Pressure Min Operating Position Pressure 3 Position Valve Ambient & Fluid Temperature Lubrication Pilot Operator Manual Override Protection Construction Electrical Rated AC Voltage DC Air and Inert Gas 50 PSI (MPa) 5 PSI (0.MPa) PSI (0.5MPa) Note ) 4~40ºF (-0~60ºC) Note ) Not Required Non Locking Push Type (Flush) Dust Proof 0VAC50/60Hz, 0V50/60Hz, 4V50/60Hz V, 4V Pilot Type Manual Override Voltage Porting Option External Pilot Type Main Valve Direct Manual Override Type Pilot Operator Non Locking Push Type (Extended), Lock Type (Tool), Lock Type (Lever) AC 00V50/60Hz, 00V50/60Hz DC 6V, 48V, 00V Bottom Ported Subplate W/Indicator Light & Surge Voltage Suppressor Allowable Voltage Range -5 ~ 0% Rated Voltage Coil Insulation Class B or Equivalent Apparent Power AC InRush 5.0VA/60Hz, 5.6VA/50Hz (Power Consumption) Holding.3VA(.5W)/60Hz, 3.4VA(.W)/50Hz Power Consumption DC.8W Electrical Entry Plug In Conduit Terminal (Base Access) Note ) Use Dry Air at Low Temperature Note ) Use Turbine Oil No (ISOVG3), if lubricated FOR FURTHER TECHNICAL DETAILS ON THIS PRODUCT, REQUEST CATALOG REFERENCE N33

18 S OLENOID VALVES S ERIES NVFS.73 H O W T O O R D E R NVFS4000 NVFS 4 0 F P OSITION Position Single Position Double 3 3 Position Closed Center 4 3 Position Exhaust Center 5 3 Position Pressure Center 6 3 Position Perfect M ANUAL O PTION 0 Standard Std & Direct Manual (Special Order) B ODY T YPE 0 Plug-In Type P ILOT O PERATOR - Internal R External (Special Order) V OLTAGE 00VAC (Special Order) 00VAC (Special Order) 3 0VAC 4 0VAc 5 4VDC 6 VDC 9 Others (Special Order) E LECTRICAL E NTRY F Through Base P ORT S IZE - Without Subplate T 3/8 NPTF *04T../ NPTF * EA, EB: 3/8 NPTF Bottom Ported: 3/8 Only P ORTING - Side *B Bottom Note) */8 NPTF Only M ANUAL O VERRIDE - Non Locking Push Type (Flush) *A Non Locking Push Type (Extended) B Lock Type (Screw Type) *C Lock Type (Lever) Note) * Special Order O PTIONS - None Z With Indicator Light and Surge Voltage Suppressor H O W T O O R D E R M ANIFOLD S EE INSIDE FRONT COVER FOR DETAILS OF YOUR LOCAL SALES OFFICE FOR FURTHER TECHNICAL DETAILS ON THIS PRODUCT, REQUEST CATALOG REFERENCE N33

19 .74 S OLENOID VALVES S ERIES NVFS H O W T O O R D E R M ANIFOLD / OPTION P ARTS ASSEMBLY FOR FURTHER TECHNICAL DETAILS ON THIS PRODUCT, REQUEST CATALOG REFERENCE N33