Rubber Seal VP300/500/700

Transcription

1 Port Pilot Operated Poppet Rubber Seal 00/500/700 High flow capacity Cv1.0 (00), Cv. (500), Cv.0 (700) Low power consumption: 1.8W(DC) Possible to use as either selector valve or divider valve Changeable from normally closed style to normally open style Vacuum applicable Up to 101.kPa - D 5- D Series 00 Series 500 Model Series Model Specifications Body ported Base mounted Port size Effective area (mm ) (Nl/min) Weight (kg) (Body ported/base mounted) (1) Series (88) (981) 0.19/0.5 Series (196) (57) 0./0. Note 1) Values for grommet style. Body ported style: Without bracket Fluid Style Pilot style Operating pressure range (MPa) Series (7) (96) 0.6/0.75 Air Normally Closed or Normally Open (Changeable) Internal pilot External pilot 0. to 0.8 Supply pressure 101.kPa to 0.8 External pilot pressure Same as supply pressure: Min. 0. Ambient and fluid temperature ( C) Max. 50 Response time (1) (ms) 0 or less (at 0.5MPa) Max. operating frequency (Hz) 5 Lubrication Not required (If requiring, turbine oil class 1 ISO VG) Non-locking push style Manual override Locking slotted style, Locking leyer style Mounting Free Impact/Vibration resistance () (m/s ) 00/50 Note 1) According to dynamic performance test JIS B (Coil temperature 0 C, at rated voltage, without surge voltage suppressor) Note ) Impact resistance: No malfunction on test using drop impact tester, to axis and right angle directions of main valve and armature, each one time when energized and de-energized. (Value in the initial stage.) Vibration resistance: No malfunction on test with 8. to 000 Hz one sweep, to axis and right angle directions of main valve and armature, each one time when energized and de-energized. (Value in the initial stage.) 7- D Option Description Bracket with screw Series 700 Model 5 7 Part No A A A Electrical entry Coil rated voltage (V) AC(50/60Hz) DC Allowable voltage Apparent power (1) (VA) AC Inrush Holding Power consumption (1) (W) DC Option Note 1) At rated voltage DIN terminal (D) 100, 00, 1,, 8, 110 to 10, 0, 0, 6, 1, 8, 100, to +10% of rated voltage 5.6(50Hz), 5.0(60Hz).(50Hz),.(60Hz) 1.8, With light JIS Symbol Style N.C. N.O. External pilot (Option) Body ported Standard Base mounted External pilot Universal Use the external pilot style in the following cases. For vacuum or the low pressure less than 0.MPa Consult SMC for the use in vacuum hold When having P port downsized in diameter When using A port as the atmospheric releasing port, e.g. air blower If manifold, external pilot piping can be centralized in manifold base.6-1

2 00/500/700 E Solenoid valve Body size 1 Base 5 8 Base 7 1 Base Valve style Common use to normally closed and normally open (Pilot) Body style Body ported Base mounted Valve option Standard (Internal pilot) R External pilot Option Ordering source area code Code areas Japan, Asia - Austria, England E Europe N North America Order Made Rated voltage V AC 50/60Hz 00V AC 50/60Hz 110 AC to 10V50/60Hz 0V AC 50/60Hz 5 V DC 6 1V DC 7 0V AC 50/60Hz 9 Others D D DO Y YO Contact SMC for other voltages (9) How to Order B Electrical entry 01 A Option F With bracket Actuation A Normally closed B Normally open Thread Rc (PT) F G (PF) N NPT Port size T NPTF Symbol Port size 5 Rc(PT) 5 Without sub-plate Light and surge voltage suppressor None Z With light and surge voltage suppressor Option DIN terminal, With connector DIN terminal, Without connector DIN terminal, With connector (DIN650C) DIN terminal, Without connector (DIN650C) (Only, 5 or 7.), 5 or 7 only. Manual override Non-locking push style B Push-locking slotted style C Push-locking lever style Option Q 7 7 SY SYJ VK VZ VG VQ VQZ How to Order Pilot Valve Assembly SF Rated voltage 1 100V AC 50/60Hz 00V AC 50/60Hz 110 to 10V AC 50/60Hz 0V AC 50/60Hz 5 V DC 6 1V DC 7 0V AC 50/60Hz 9 Others 1 D Z B 50 Q Manual override Non-locking push style B Push-locking slotted style C Push-locking lever style Option Light and surge voltage suppressor None Z With light and surge voltage suppressor Electrical entry D DO Y YO DIN terminal, With connector DIN terminal, Without connector DIN terminal, With connector (DIN650C) DIN terminal, Without connector (DIN650C).6-

3 00/500/700 Application Examples qblow off valve rvacuum control valve Precautions Be sure to read before Handing. Refer to the p.0- to 0-6 Safety Instructions and common precautions. External pilot model wpressure release valve tdivider valve Vacuum releasing air Atmospheric pressure or small pressure External pilot yoperation of a single acting cylinder Caution Change of Actuation 1) Base mounted N.C. N.O. eselector valve uoperation of a double acting cylinder ioperation of a double acting cylinder (Exhaust centre) When changing the actuation from normally closed style to normally open style, remove the body from the sub plate and reset the mark on the body corresponding to the NO mark on the sub plate as shown in the figure above. It is not necessary to change the piping at that time. ) Body ported N.C. N.O. Caution Light and Surge Voltage Suppressor Rated voltage AC Circuit Surge voltage suppressor Light and surge voltage suppressor Symbol S Z DIN terminal (D) DZ More than 100V AC DZ Less than V AC Electrical Connection For grommet with surge voltage suppressor for DC specification please correctly connect the lead wires to positive and negative indications on the connector. For non-polar style such as DIN connector or Terminal, the lead wires can be connected to either one. Grommet Lead wire color Polarity Red Black + DIN terminal or Terminal With DIN terminal block With terminal block When changing the actuation from normally closed style to normally open style, remove the body from the sub plate and reset the mark on the body corresponding to the NO mark on the sub plate as shown in the figure above. Refer to the following table for piping. Actuation N.C. N.O. Port P Upstream Exhaust side A Downstream Downstream R Exhaust side Upstream Change of Electrical Entry 1) Push out the body of DIN terminal from the cover, turn it at 180 and then insert it. ) Remove pilot valve mounting screws (M, pcs.), rotate the pilot valve at 180 and then re-tighten the valve with the screw. Surge voltage suppressor S Piping DC Light and surge voltage suppressor Z DZ More than 100V DC DZ Less than V DC Pilot solenoid valve is easy to generate the voltage drop due to the small flow upstream of the valve. It causes the valve to malfunction. Select the I.D. fitting size more than ø8 for and, more than ø10 for 5 and 5, more than ø1 for 7 and 7 when piping length is less than metres. Use the external pilot for the case of small flow upstream of the valve. How to calculate the flow rate Please refer to the p.0-6 for the details..6-

4 00/500/700 Construction Body Ported Base Mounted SY SYJ VK VZ VG VQ VQZ Component Parts No. Description Material q Body Aluminium die cast w Adapter plate Aluminium die cast e End plate Aluminium die cast r Retainer Brass t Spool valve Aluminium/NBR y Piston Resin u Spring SUS Note Painted silver Painted silver Painted silver Replacement Parts No. Description i Sub plate o Pilot valve ass y Part No P 00--P P 500--P P 700--P SF- -50 Note, 1 8, 1 5, 1 Aluminium die cast 5, 8 7, 8 7, 1 Refer to How to Order Pilot Valve Assembly on p

5 00 00: Body ported/dimensions Grommet (G) DIN terminal (D) (Y).6-5

6 00 00: Base mounted/dimensions Grommet (G) SY SYJ VK VZ VG VQ VQZ DIN terminal (D) (Y).6-6

7 : Body ported/dimensions Grommet (G) DIN terminal (D) (Y).6-7

8 : Base mounted/dimensions Grommet (G) SY SYJ VK VZ VG VQ VQZ DIN terminal (D) (Y).6-8

9 : Body ported/dimensions Grommet (G) DIN terminal (D) (Y).6-9

10 : Base mounted/dimensions Grommet (G) SY SYJ VK VZ VG VQ VQZ DIN terminal (D) (Y).6-10

11 00/500/700 Manifold Piping is concentrated at the base side. All external pilots are gathered in the base. Common external, pilot port allows one piping. styles of exhaust ports Select either a common or individual exhaust port. Individual exhaust style is possible to control the flow rate. Easy to change switching style. (Nomally Closed or Nomally Open) Switching style is easily changed from nomally closed to nomally open by changing the direction of the valve only 180. Specifications Manifold style R(EXH) style P(SUP) style Valve stations Model B mount Single base Common EXH, Individual EXH Common SUP Max. 0 In case of more than 10 stations, use SUP/EXH ports to supply/exhaust pressure. Series Manifold base part number VVP-1- No. of stations 1-0 VVP-- No. of stations -0 VVP5-1- No. of stations 1-0 VVP5-- No. of stations -0 VVP7-1- No. of stations 1-0 VVP7-- No. of stations -0 R port style Common Individual Common Individual Common Individual Port size (P.A.R) Applicable valve model Common external pilot style (VVP -1R, -R). In case of external pilot manifold, valve is external pilot style (standard specification). 1 Option Description Blank plate assembly (with gasket and mounting screw) Part No A A A Applicable manifold base model VVP VVP5 VVP7 VVP How to Order E VVP Series port solenoid valve manifold Body size 1 standard 5 8 standard standard Base specifications Common exhaust Individual exhaust Supply port is common. Special specifications Standard R Common external pilot Ordering source area code Code - E N areas Japan, Asia Austria, England Europe North America Stations 0 stations 0 0 stations Port size Symbol Port size Symbol Symbol Flow passage Piping P R A 1 Common Common Side Common Individual Side Thread(P, R port) - F N T Rc (PT) G (PF) NPT NPTF Applicable manifold base model VVP VVP5 VVP7 Note 1 type type Note) The part numbers of valve and blank plate are required to order. Ex.) stations manifolds VVP D-Q A (Blank plate)

12 00 VVP/Dimensions (N.C.) Common exhaust: VVP-1 - Number of stations 1-0 (D)(Y) (G) SY SYJ VK VZ VG Individual exhaust: VVP- - Number of stations -0 n L L1 L Calculation formula L1=7.5 X n+8.5 L=7.5 X n+1.5 VQ VQZ (D)(Y) (G) L L1 L n Calculation formula L1=7.5 X n+8.5 L=7.5 X n

13 500 VVP5/Dimensions (N.C.) Common exhaust: VVP5-1 - Number of stations 1-0 (D)(Y) (G) L n L1 L Calculation formula L1= X n+9 L= X n+1 Individual exhaust: VVP5- - Number of stations -0 (D)(Y) (G) n L L1 L Calculation formula L1= X n+9 L= X n+1.6-1

14 700 VVP7/Dimensions (N.C.) Common exhaust: VVP7-1 - Number of stations 1-0 (D)(Y) (G) SY SYJ VK VZ VG L n L1 L Calculation formula L1=1 X n+ L=1 X n+17 VQ Individual exhaust: VVP7- - Number of stations -0 VQZ (D)(Y) (G) n L L1 L Calculation formula L1=1 X n+ L=1 X n