3 Port Solenoid Valve Direct Operated Poppet Type

Transcription

1 3 Port Solenoid Valve Direct Operated Poppet Type VK300 Series Rubber Seal [Option] Universal porting Available for N.C. valve, N.O. valve, divider valve, selector valve, etc. C: 0.80 dm 3 /(s bar) (Passage 3) Compact: Width 18 x Length 63 (mm) Low power consumption 4 W DC (Standard type) W DC (Low wattage type) Suitable for use in vacuum applications 101. kpa Suitable for use in copper-free applications The portions that come in contact with fluids do not contain copper, thus enabling the standard product to be used as is. Specifications Type of actuation Fluid Ambient and fluid temperature Response time (at 0.5 MPa) (1) Lubrication Mounting orientation Impact/Vibration resistance Enclosure () Direct operated type position single solenoid Air 5 to 50 C (No freezing) 10 ms or less (Standard), 15 ms or less (Low power consumption type) Non-locking push type Not required (Use turbine oil Class 1 ISO VG3, if lubricated.) Unrestricted 300/50 m/s Dustproof Note1) Based on dynamic performance test, JIS B 8419: 10. ( temperature: C, at rated voltage, without surge suppressor) Note) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 00 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Symbol (A) Base mounted Base mounted (A) Solenoid Specifications Electrical entry Rated voltage (V) Allowable voltage fluctuation Standard Apparent power (AC) type Continuous duty type Power consumption (DC) Surge voltage suppressor Indicator light At the rated voltage AC DC Inrush Holding Inrush Holding W/o indicator light W/ indicator light AC DC AC DC Grommet (G), DIN terminal (D) 100, 110, 0,, 40 1, 4 ±10% of rated voltage 9.5 VA/50 Hz, 8 VA/60 Hz 7 VA/50 Hz, 5 VA/60 Hz 3.5 VA/50 Hz, 3.3 VA/60 Hz 3 VA/50 Hz,.8 VA/60 Hz 4 W (Standard), W (Low power consumption type) 4.3 W (Standard),.3 W (Low power consumption type) ( for 1 VDC or less) Neon bulb LED (R)3 1(P) Base mounted (With sub-plate) Valve model (P)1 3(R) Flow Rate Characteristics/Weight Operating pressure range (MPa) Port size VK33 VK33Y (For low wattage, W DC) 0 to 0.7 VK33E (Continuous duty type) M5 x 0.8 VK33V (For vacuum) VK33W (Low wattage, vacuum) VK334 VK334Y (For low wattage, W DC) 101. kpa to to VK334E (Continuous duty type) VK334V (For vacuum) VK334W (Low wattage, vacuum) 101. kpa to Mounting with VK300 The VK300 series can be mounted on the manifold base VV5K3 of VK 3000 series. Refer to page 14 for details. Flow rate characteristics 1 (P A) 3 (A R) 3 (R A) 1 (A P) C [dm 3 / (s bar)] C [dm 3 / (s bar)] C [dm 3 / (s bar)] C [dm 3 / (s bar)] b Cv b Cv b Cv b Cv Weight (g) Grommet VV061 VV100 V100 S070 VQD VQD-V VK VT

2 VK300 Series How to Order Note) CE-compliant: For DIN terminal only [Option] Valve option Rated voltage 100 VAC, 50/60 Hz 0 VAC, 50/60 Hz 110 VAC, 50/60 Hz VAC, 50/60 Hz 4 VDC 1 VDC 40 VAC, 50/60 Hz Rated voltage Note1) Applicable only for DIN terminal type Note) For other rated voltages, please consult with SMC. V Y W E Electrical entry G: Grommet (Lead wire length: 300 mm) H: Grommet (Lead wire length: 600 mm) D: DIN terminal DO : DIN terminal (Without connector) CE-compliant For the connector part number, refer to page Option Port size M5 M5 x None P, R port: M5 With bracket (Not assembled) Thread type F N T Rc G NPT NPTF F Option Part No. Description Part no. Note Bracket VK With screw Base mounted VK33 VK334 1 G M5 1 G 01 Construction Symbol (A) V Y W E Valve option Standard type For vacuum For low wattage For vacuum/low wattage Continuous duty type Port size Without sub-plate 01 (With sub-plate) 1 8 Light/Surge voltage suppressor None S With surge voltage suppressor Z With light/surge voltage suppressor (Type D only) CE-compliant Note) Since the indicator light is bulit in connector, thus, DOZ is not available. The continuous duty AC type is equipped with a rectifier, so a diode will be provided. CE-compliant Q CE-compliant Note) Applicable only for DIN terminal type (R)3 1(P) Component Parts No. Description Material 1 Body Aluminum die-casted 3 Cover End cover Resin Resin 4 Spool valve assembly Aluminum, NBR 5 Return spring Stainless steel 6 Molded coil Resin Note Platinum silver Black Black Black A 1410

3 VK300 Series Manifold Specifications VV3K3-S VV3K3--04 Common SUP/Common EXH Type : (A port top ported) A port: Rc 1/8, M5 x 0.8 Type 40: Base mounted (A port bottom ported) Type 4: Base mounted (A port side ported) A port: Rc 1/8 Type S4 (Solenoids on the same side of A port) A port: Rc 1/8 Common SUP/Individual EXH Type 1: (A port top ported) A port: Rc 1/8, M5 x 0.8 A port: Rc 1/8 P port: Rc 1/8 R port: Rc 1/8 P port: Rc 1/8 R port: Rc 1/8 Note) For 9 stations or more, supply air both sides of P port. The common exhaust type should exhaust from both of the R port. Note) CE-compliant: For DIN terminal only How to Order VV3K3 05 Valve stations 01 P port: Rc 1/8 R port: Rc 1/8 R port: Rc 1/8 P port: Rc 1/8 Valve stations Piping method 1 station stations How to Order VV3K P port: Rc 1/8 Valve stations R port: Rc 1/ station stations How to Order Option None With bracket F (Not mounted) Port size 01 Rc 1 8 VV3K Solenoid direction S Specifications Opposite side of A port Same side of A port Valve stations 01 1 station stations How to Order VV3K Valve stations 01 1 station Common SUP, Common EXH Common SUP, Individual EXH stations Thread type F N T Rc G NPT NPTF Port size P, R port thread type 00F 00N 00T Rc G NPT NPTF Option F 1 to, Base mounted None [Option] Applicable solenoid valve VK33--M5(-Q) VK33--01(-Q) Applicable blanking plate assembly VK A Bracket VK A CE-compliant Q CE-compliant Note) Applicable only for DIN terminal type Applicable solenoid valve VK334-(-Q) Applicable blanking plate assembly VK A Bracket VK A With bracket CE-compliant (Not mounted) Q CE-compliant Note) Applicable only for DIN terminal type Applicable solenoid valve VK334-(-Q) Applicable blanking plate Thread assembly VK A type 01 Rc 1 8 Rc C4 ø4 cassette F G C6 ø6 cassette N T NPT NPTF P, R port thread type 00F 00N 00T Rc G NPT NPTF CE-compliant Q CE-compliant Note) Applicable only for DIN terminal type Applicable solenoid valve VK33--M5(-Q) VK33--01(-Q) Applicable blanking plate assembly VK A CE-compliant Q CE-compliant Note) Applicable only for DIN terminal type 1411 VV061 VV100 V100 S070 VQD VQD-V VK VT

4 VK300 Series Combinations of Solenoid Valve, Manifold Gasket and Manifold Base 3 port body ported: VK33 3 port base mounted: VK334 M3 x 6 Round head combination screw M3 x 6 Round head combination screw Manifold gasket Manifold gasket Applicable base VV3K3- (-Q) 1 (-Q) VV5K3- (-Q) Manifold base 1 (-Q) Manifold gasket and screw assembly VK A Base mounted VK Note1) Mounting direction is fixed, do not mount on opposite side. Note) The VK300 series can be mounted on the manifold base VV5K3 of VK 3000 series. Refer to page 14 for details. Applicable base VK Sub-plate VV3K3-40 (-Q) (S) 4 (-Q) VV5K3-40 (-Q) Manifold base (S) 41 (-Q) (S) 4 (-Q) Mounting Screw Tightening Torques M3: 0.6 N m Combinations of Blanking Plate Assembly and Manifold Base Blanking plate assembly: VK A M3 x 8 Round head combination screw Blanking plate 141 Manifold gasket for blanking plate Applicable base: In common for all types of VV3K3 models Mounting Screw Tightening Torques M3: 0.6 N m

5 3 Port Solenoid Valve Direct Operated Poppet Type VK300 Series Dimensions: Body Ported Grommet: VK33-G- M5 01 DIN terminal: VK33-D- M5 01 (Bracket) Max M5: M5 x 0.8 [01: 1/8] x M.5 x 0.45 (Mounting screw) x ø3. [14] (Mounting hole for manifold) (Mounting screw) M5: M5 x 0.8 [01: 1/8] 16 [14] x ø3. (Mounting hole for manifold) (Bleed hole) 3R x M5 x 0.8 (P, A, R port) x ø Refer to grommet type for other dimensions. [ ]: For port size 01 Dimensions: Base Mounted Grommet: VK334-G-01 DIN terminal: VK334-D-01 x ø A P x ø4.3 (Mounting hole) 3 x Rc 1/8 (Piping port) Max x Rc 1/8 (Piping port) P R VV061 VV100 V100 S070 VQD VQD-V VK VT Refer to grommet type for other dimensions A

6 VK300 Series Type Manifold/Body Ported (Top ported) VV3K3-- Stations n1 = Number of VK300 Grommet: G DIN terminal: D n1 x Rc 1/8 (Mounting hole) 4 x Rc 1/ Max x Rc1/ x M3 x 0.5 depth 6 (Bracket mounting screw) L Dimension L L1 L L3 n n: Stations

7 3 Port Solenoid Valve Direct Operated Poppet Type VK300 Series Type 1 Manifold/Body Ported (Top ported) VV3K3-1- Stations n1 = Number of VK300 Grommet: G DIN terminal: D n1 x Rc 1/ x Rc 1/8 (P port) x Rc 1/8 (P port) 68.8 Max n x Rc 1/8 (R port) L Dimension L L1 L n n: Stations VV061 VV100 V100 S070 VQD VQD-V VK VT 1415

8 VK300 Series Type 40 Manifold/Base Mounted (Bottom ported) VV3K3-40- Stations -01 Grommet: G 4 x Rc 1/8 DIN terminal: D Max x Rc 1/ x M3 x 0.5 depth 6 (Bracket mounting screw) n x Rc 1/8 L Dimension L L1 L L3 n n: Stations

9 3 Port Solenoid Valve Direct Operated Poppet Type VK300 Series Type 4 Manifold/Base Mounted (Side ported) VV3K3-4- Stations -01 Grommet: G DIN terminal: D Max x Rc 1/ x Rc 1/ n x Rc 1/8 Built-in One-touch fitting: VV3K3-4- Stations -C4, C6 Solenoid at A port side: VV3K3-S4- Stations - 4 x Rc 1/8 L L1 L n x One-touch fitting C4: Applicable tubing T045 C6: Applicable tubing T0604 n Max.5.5 Refer to the above drawing for DIN terminal dimensions Refer to the above drawing for other dimensions n x Rc 1/ VV061 VV100 V100 S070 VQD VQD-V VK VT

10 No. VK300 Series Specific Product Precautions Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages 3 to 9 for 3/4/5 Port Solenoid Valve Precautions. How to Wire DIN Terminal Connection 1. Loosen the set screw and pull out the connector from the terminal block of the solenoid.. Remove screw and insert screwdriver into the slit area near the bottom of terminal block to separate block and housing. 3. Loosen the terminal screws (slotted screws) on the terminal block, insert the core of the lead wire into the terminal, and attach securely with the terminal screws. 4. Tighten the ground nut to secure the cable. Use caution in wiring because it will not meet the IP65 (enclosure) standard if you use the other cable than prescribed heavy-duty cable of size (ø3.5 to ø7). Tighten the ground nut and set screw within the specified range of torque. Change of electrical entry (Orientation) After separating terminal block and housing, the cable entry direction can be changed by attaching the housing in the desired direction (4 directions in 90 increments). In the case of w/ indicator light, avoid damaging the light with lead wire. Precautions Plug a connector in or out vertically, never at an angle. Applicable cable O.D.: ø3.5 to ø7 (Reference) 0.5 mm core and 3 core wires equivalent to JIS C 3306 Ground nut Tightening torque 1.65 to.5 N m Washer Holding screw Tightening torque 0.3 to 0.4 N m Grommet (Rubber) (Voltage symbol) Refer to the table below. Terminal screw (3 positions) Housing (Position for light mounting) Terminal block Slot area Tightening torque 0. to 0.5 N m Connector part no.: VK Part no. of connector with indicator light Rated voltage Voltage symbol Part no. 100 VAC 100V VK VAC 110V VK VAC 0V VK VAC V VK VAC 40V 6 VDC 6V 1 VDC 1V 4 VDC 4VD 48 VDC 48VD VK VK VK VK VK Circuit with indicator light AC circuit 1 VDC or less 4 VDC or more diagram circuit diagram circuit diagram LED R NL R D LED R Light/Surge Voltage Suppressor Rated Grommet (G) Standard: voltage Y, V, W duty Continuous type (E) AC DC 4V 48V DC 6V 1V W/o indicator light With indicator light W/o indicator light With indicator light W/o indicator light With indicator light Red (+) Black () None None None Grommet type DIN terminal type Marking DIN terminal (D) Standard: Y, V, W duty Continuous type (E) No. (G, GS) (+) No.( ) (+) LED No.( ) No. No. No. (D, DS) No. Part no. symbol Precautions on connection of 4 V or more DC Grommet type should be connected as following; Red lead wire for (+) side, Black lead wire for () side respectively. With the DIN terminal, connect the positive (+) side to the connector s no. 1 terminal, and the negative () side to the no. terminal. [Refer to the marks on the terminal board.] For 1 VDC or below, there is no positive (+) or negative () directionality. Neon bulb Neon bulb Red (+) Black () Surge voltage suppressor S Z S Z S Z Indicator light (Built-in connector) Surge voltage suppressor (Built-in terminal) Warning Valve Mounting Direction When mounting a valve on the manifold base or sub-plate, etc., the mounting orientation is already decided. If mounted in a wrong direction, the equipment to be connected may result in malfunction. Refer to pages 1413 to 1417 for external dimensions in mounting. Vacuum Spec. Type: VK33V (VK33W) In contrast to the standard product, this vacuum specification valve has less air leakage at low pressures, a feature that should be taken into consideration when using this valve for vacuum applications. 1. Since this valve has slight air leakage, it can not be used for holding vacuum (including positive pressure holding) in the pressure container. Continuous Duty Type: VK33E Recommended for continuous duty with long time loading. 1. This model is for continuous duty, not for high cycle rates. But even in low cycle rates, if energizing the valve more than once a day, please consult with SMC.. Energizing solenoid should be done at least once in 30 days. How to Calculate the Flow Rate For obtaining the flow rate, refer to front matter. A 1 NL: Neon bulb R: Resister LED: Light emitting diode R: Resister 1 + D: Protective diode LED: Light emitting diode R: Resister Marking AC, 1 VDC or less for DC For 4 V or more