5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported

Transcription

1 For details about certified products conforming to international standards, visit us at 5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported Series VFS2000 Model 2 position 3 position Type of actuation Single Double Closed center Exhaust center Pressure center Plug-in VFS2120 VFS2220 VFS2320 VFS2420 VFS2520 Model Non plug-in VFS2130 VFS2230 VFS2330 VFS2430 VFS2530 Port size Rc Flow characteristics 1 4/2 (P A/B) 4/2 5/3 (A/B R1/R2) C C [dm 3 /(s bar)] b Cv [dm 3 /(s bar)] b Cv Note 1) Based on JIS B 8375 (once per 30 days) for the minimum operating frequency. Note 2) According to JIS B (The value at supply pressure 0.5 MPa.) Note 3) In the case of grommet type Note 4) Factors of Note 1) and Note 2) are achieved in controlled clean air. Compact yet provides a high flow capacity 1/4: C: 3.4 dm 3 /(s bar) Low power consumption: 1.8 W DC VFS2320- T- VFS2220- E- JIS Symbol 2 position 3 position Single Closed center Double VFS2120- E--F VFS2120- G- Exhaust center Standard Specifications Valve specifications Electricity specifications Option Specifications Fluid Maximum operating pressure Minimum operating pressure Proof pressure Ambient and fluid temperature Lubrication Pilot valve manual override Shock/Vibration resistance Enclosure Allowable voltage fluctuation Coil insulation type Apparent power Inrush (Power consumption) AC Holding Power consumption Electrical entry Max. operating cycle (cpm) (1) (2) (3) Response time (ms) 22 or less 13 or less 40 or less 40 or less 40 or less Air/Inert gas 1.0 MPa 0.1 MPa 1.5 MPa 10 to 60 C (1) Non-lube (2) Non-locking push type (Flush) 150/50 m/s 2 (3) Dustproof (Degrees of protection 0) (4) 100, 200 VAC, 50/60 Hz; 24 VDC 15 to +10% of rated voltage Class B or equivalent (130 C) (5) 5.6 VA (50 Hz), 5.0 VA (60 Hz) 3.4 VA (2.1 W)/50 Hz, 2.3 VA (1.5 W)/60 Hz 1.8 W (2.04 W: ) Grommet, Grommet terminal, Conduit terminal, DIN terminal Note 1) Use dry air at low temperatures. Note 2) Use turbine oil Class 1 (ISO VG32), if lubricated. Note 3) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Note 4) Based on JIS C Note 5) Based on JIS C Pilot type External pilot (1) Pilot valve manual override Non-locking push type (Extended), Locking type (Tool required) 110 to 120, 220, 240 VAC (50/60 Hz) 12, 100 VDC Option (2) Foot bracket (With screw) Part no.: VFN200-17A, VFS2120 (single) only Note 1) Operating pressure: 0 to 1.0 MPa. Pilot pressure: 0.1 to 1.0 MPa. Note 2) No light grommet but surge voltage suppressor (direct connecting lead wire) is installed. Weight (kg) VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Pressure center Manifold Body type VFS2 20 VFS2 30 Applicable manifold base (Pilot EXH) Bar manifold (Individual EXH) Bar manifold (Common EXH base side) Note) VFS2 30: Manifold only. Cannot be used as a single unit

2 Series VFS2000 How to Order 1 2 VFS2 Symbol 2 position single 2 position double G 01 Port size N 01 Rc T Rc F Thread type Rc NPT NPTF G Option F: With foot bracket 3 3 position closed center : Non-locking push type (Flush) A : Non-locking push type (Extended) B : Locking type (Tool required) Mountable only for VFS position exhaust center position pressure center Reverse pressure: Can be used by external pilot specifications. Body (Pilot exhaust) 20: Individual EXH /Surge voltage suppressor None Z S With surge voltage suppressor Indicator light is not available for grommet type. With surge voltage suppressor is available for grommet type only. Electrical entry G: Grommet E: Grommet terminal T: Conduit terminal D, Y: DIN terminal 30: Common EXH How to Order Pilot Valve Assembly Manifold only Pilot type Internal pilot R External pilot : Individual external pilot (External pilot port: Body side) SF4 100 VAC, 50/60 Hz 200 VAC, 50/60 Hz 110 to 120 VAC (50/60 Hz) 220 VAC, 50/60 Hz 24 VDC 12 VDC 240 VAC, 50/60 Hz Other 1 DZ 12 Electrical entry, /Surge voltage suppressor G GS D DZ DO DOZ Y YZ YO YOZ T TZ E EZ VAC (50/60 Hz) VAC (50/60 Hz) to 120 VAC (50/60 Hz) VAC (50/60 Hz) 5 24 VDC 6 12 VDC VAC (50/60 Hz) 9 Other Grommet Grommet with surge voltage suppressor DIN terminal DIN terminal with light/surge voltage suppressor DIN terminal DIN terminal with light/surge voltage suppressor DIN terminal DIN terminal with light/surge voltage suppressor DIN terminal DIN terminal with light/surge voltage suppressor Conduit terminal Conduit terminal with light/surge voltage suppressor Grommet terminal Grommet terminal with light/surge voltage suppressor Y: Conforming to DIN43650B standard DIN connector is not attached. Applicable model For VFS2 20 For VFS2 30 Individual pilot exhaust Common pilot exhaust A Non-locking push type (Flush) Non-locking push type (Extended) B Locking type (Tool required)

3 5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported Series VFS2000 Cylinder Speed Chart Body Ported Series VFS2120- Conditions Construction Averag speed (mm/s) Bore size Series CJ2 Pressure 0.5 MPa Load factor 50% Stroke 60 mm Series CM2 Pressure 0.5 MPa Load factor 50% Stroke 300 mm Series MB/CA1 Note) Pressure 0.5 MPa Load factor 50% Stroke 500 mm ø6 ø10 ø16 ø20 ø25 ø32 ø40 ø40 ø50 ø63 ø80 ø100 Body ported Series CJ2 Series CM2 Series MB/CA1 Note) VFS2120- Tube bore x Length Speed controller Silencer T0604 x 1 m AS3001F-06 T1075 x 1 m AS4001F-10 AN Use as a guide for selection. Please confirm the actual conditions with SMC Sizing Program. It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open. The average velocity of the cylinder is what the stroke is divided by the total stroke time. Load factor: ((Load weight x 9.8)/Theoretical force) x 100% Note) The Series CA1 has been changed to the Series CA2. 2 position single 2 position double Perpendicular, upward actuation Horizontal actuation VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Closed center 3 position closed center/exhaust center/pressure center Exhaust center Pressure center Component Parts No. Description q Body w Spool/Sleeve e End plate r Piston Material Aluminum die-casted Stainless steel Resin Resin Note Platinum silver Replacement Parts No. Description Material t Return spring Stainless steel y Pilot valve assembly u Detent assembly Part no. VFS2120 VFS2220 VFS2320/2420/2520 VFS VFS Refer to How to Order Pilot Valve Assembly on page VFN2000-8A

4 Series VFS Position Single Grommet: VFS2120- G Grommet, Grommet terminal, Conduit terminal, DIN terminal Foot bracket (F) Part no.: VFN200-17A M5: External pilot port ( Only for external pilot model. ) 2-ø4.5 mounting hole Solenoid valve 300 (Lead wire length) 3-Rc 1/8, 1/4 2-Rc 1/8 Grommet terminal: VFS2120- E/EZ DIN terminal: VFS2120- D/DZ/Y/YZ Lead wire O.D. Max. ø3.5 (EZ) Applicable heavy-duty code O.D. ø6 to ø8 (Y: ø4.7 to ø7) (DZ) Conduit terminal: VFS2120- T/TZ Applicable heavy-duty code O.D. ø6 to ø8 (TZ) ( ): Y, YZ

5 5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported Series VFS Position Double, 3 Position Grommet, Grommet terminal, Conduit terminal, DIN terminal Grommet: VFS2220- G, VFS2320- G, VFS2420- G, VFS2520- G 182 (3 position: 192.5) 300 (Lead wire length) Grommet terminal:vfs2220- E/EZ VFS2320- E/EZ VFS2420- E/EZ VFS2520- E/EZ Lead wire O.D. Max. ø3.5 (EZ) 182 (3 position: 193) (M5: External pilot port Only for external pilot model.) 3-Rc 1/8, 1/4 2-Rc 1/8 DIN terminal: VFS2220- D/DZ/Y/YZ VFS2320- D/DZ/Y/YZ VFS2420- D/DZ/Y/YZ VFS2520- D/DZ/Y/YZ VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Applicable heavy-duty code O.D. ø6 to ø8 (Y: ø4.7 to ø7) (DZ) 219 (3 position: 229) Conduit terminal:vfs2220- T/TZ VFS2320- T/TZ VFS2420- T/TZ VFS2520- T/TZ ( ): Y, YZ Applicable heavy-duty code O.D. ø6 to ø8 (TZ) 219 (3 position: 229)

6 For details about certified products conforming to international standards, visit us at 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Series VFS2000 Model 2 position 3 position Type of actuation Single Double Closed center Exhaust center Pressure center Double check Plug-in VFS2100 VFS2200 VFS2300 VFS2400 VFS2500 VFS2 Note 1) Based on JIS B 8375 (Once per 30 days) for the minimum operating frequency. Note 2) Based on JIS B (The value at supply press. 0.5 MPa). Note 3) Values for VFS2 00- FZ-01. Note 4) Factors of Note 1) and Note 2) are ones achieved in controlled clean air. Compact yet provides a large flow capacity 1/4: C: 2.8 dm 3 /(s bar) Low power consumption: 1.8 W DC Easy maintenance 2 types of sub-plates: Plug-in and non plug-in JIS Symbol Non plug-in type Model Non plug-in VFS2110 VFS2210 VFS2310 VFS2410 VFS2510 VFS2610 Plug-in type 2 position 3 position Single Closed center Double Exhaust center Pressure center Double check Port size Rc Flow characteristics 1 4/2 (P A/B) 4/2 5/3 (A/B R1/R2) C C [dm 3 /(s bar)] b Cv [dm 3 /(s bar)] b Cv Standard Specifications Valve specifications Electricity specifications Fluid Maximum operating pressure 2 position Min. operating pressure 3 position Proof pressure Ambient and fluid temperature Lubrication Pilot valve manual override Shock/Vibration resistance Enclosure Allowable voltage fluctuation Coil insulation type Apparent power Inrush (Power consumption) AC Holding Power consumption DC Electrical entry Option Specifications or less 13 or less 20 or less 20 or less 20 or less 25 or less Air/Inert gas 1.0 MPa 0.1 MPa 0.15 MPa 1.5 MPa 10 to 60 C (1) Non-lube (2) Non-locking push type (Flush) 150/50 m/s 2 (3) Type G, E: Dustproof (Class 0), Type F, T, D: Splashproof (Class 4) (4) 100, 200 VAC, 50/60 Hz; 24 VDC 15 to +10% of rated voltage Class B or equivalent (130 C) (5) 5.6 VA/50 Hz, 5.0 VA /60 Hz 3.4 VA (2.1 W)/50 Hz, 2.3 VA (1.5 W)/60 Hz 1.8 W (2.04 W: ) Plug-in type Conduit terminal Non plug-in type Grommet terminal, DIN terminal Note 1) Use dry air at low temperatures. Note 2) Use turbine oil Class 1 (ISO VG32), if lubricated. Note 3) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and deenergized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Note 4) Based on JIS C Note 5) Based on JIS C Pilot type Porting specifications Option External pilot Note) Non-locking push type (Extended), Locking type (Tool required), Locking type (Lever) 110 to 120, 220, 240 VAC, 50/60 Hz 12, 100 VDC Bottom ported Note) Operating pressure: 0 to 1.0 MPa Pilot pressure 2 position: 0.1 to 1.0 MPa 3 position: 0.15 to 1.0 MPa Compact, lightweight type sub-plate Compared with the standard type, this is the subplate having the reduced external dimensions and lighter weight. But, use caution that Cv factor or piping port position is different from the standards. For details, refer to page Sub-plate Max. operating cycle (cpm) L (mm) Weight (kg) Standard type Compact type position single Rc 1/4 (1) (2) Response time (ms) Sonic conductance C [dm 3 /(s bar)] (3) Weight (kg) VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN

7 Series VFS2000 How to Order With attachment plug lead wire With terminal block Body type O: Plug-in type sub-plate Z Option None Electrical entry F: Plug-in type Porting specifications B Side ported Bottom ported Port size 01 Rc Rc N T F Rc NPT NPTF G Without sub-plate Plug-in type conduit terminal (With terminal block) Standard type Note) Plug-in type grommet P01 Rc (With attachment Note) plug lead wire) P Rc Compact type Note) Please note Cv Thread type factor and piping port location of compact subplate is different from standard. Refer to page for details. Plug-in VFS F Symbol 2 position single 2 position double 3 position closed center 3 position exhaust center 3 position pressure center 3 position double check VFS Non plug-in 2 Body type 1: Non plug-in type sub-plate R 10 Pilot type Internal pilot External pilot : External pilot is possible only to the one with sub-plate. 100 VAC, 50/60 Hz 200 VAC, 50/60 Hz 110 to 120 VAC, 50/60 Hz 220 VAC, 50/60 Hz 24 VDC 12 VDC 240 VAC, 50/60 Hz Other 1 E Port size Pilot valve manual override : Non-locking push type B Without sub-plate : Locking type (Flush) (Tool required) Rc 01 Non plug-in type, Standard Rc type A : Non-locking push type C Note) Rc : Locking type Non plug-in type, S01 1 (Extended) (Lever) 8 Compact Note) Rc type S Note) Please note Cv factor and piping Option port location of compact sub-plate None are different from standard. Refer to Z page for S With surge voltage suppressor details. Indicator light is not available for grommet type. With surge voltage suppresor is avilable for grommet type only. Electrical entry G: Grommet E: Grommet terminal T: Conduit terminal D, Y: DIN terminal VAC, 50/60 Hz VAC, 50/60 Hz to 120 VAC (50/60 Hz) VAC, 50/60 Hz 5 24 VDC 6 12 VDC VAC, 50/60 Hz 9 Other G GS How to Order Pilot Valve Assembly SF4 Electrical entry, /Surge voltage suppressor F Plug-in Plug-in D DZ DO DOZ Y YZ Grommet Grommet with surge voltage suppressor DIN terminal DIN terminal with light/surge voltage suppressor DIN terminal DIN terminal with light/surge voltage suppressor DIN terminal DIN terminal with light/surge voltage suppressor Non plug-in 1 DZ 20 YO YOZ T TZ E EZ DIN terminal DIN terminal with light/surge voltage suppressor Conduit terminal Conduit terminal with light/surge voltage suppressor Non plug-in Grommet terminal Grommet terminal with light/surge voltage suppressor DIN connector is not attached. Refer to page for voltage conversion. Y: Conforming to DIN43650B standard Manual override Non-locking push type (Flush) A Non-locking push type (Extended) B Locking type (Tool required) C Locking type (Lever)

8 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Series VFS2000 Cylinder Speed Chart System Components System Solenoid valve A B System A B Series VFS2000 Rc Series VFS2000 Rc Average speed (mm/s) Speed controller Silencer AS3000- AN (S = 12 mm 2 ) (S = 35 mm 2 ) AS4000- (S = 21 mm 2 ) Use as a guide for selection. Please confirm the actual conditions with SMC Sizing Program. Bore size Series CM Pressure 0.5 MPa Load factor 50% Stroke 300 mm Series MB Pressure 0.5 MPa Load factor 50% Stroke 500 mm Series CS1 Pressure 0.5 MPa Load factor 50% Cylinder stroke 1000 mm ø20 ø25 ø32 ø40 ø40 ø50 ø63 ø80 ø100 ø125 ø140 ø160 AN (S = 35 mm 2 ) Tube bore x Length T0604 x 1 m T1075 x 1 m Perpendicular, upward actuation Horizontal actuation It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open. The average velocity of the cylinder is what the stroke is divided by the total stroke time. Load factor: ((Load weight x 9.8)/Theoretical force) x 100% VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Double Check Spacer/Specifications Can hold an intermediate cylinder position for an extended time If the double check spacer with a built-in double check valve is combined, it will enable the cylinder to stop in the intermediate stroke and maintain its position for a long time without being affected by the leakage between the spools. Double check spacer Specifications Double check spacer part no. Applicable valve model Plug-in type VVFS A-1 VFS2400- F Solenoid one side energized Leakage (cm 2 /min) Solenoid both sides de-energized P P A B Non plug-in type VVFS A-2 G ET VFS2410- D R1 R2 R1 R2 R1 R2 210 or less 210 or less Supply pressure: 0.5 MPa Caution In the case of 3 position double check valve (VFS26 0), check the leakage from piping and fittings in between valve and cylinder by means of synthetic detergent solutions, and ensure that there is no such leakage found there. Also check the leakage from cylinder seal and piston seal. If there is any leakage, sometimes the cylinder, when valve is de-energized, can move without stopping at intermediate position. Be aware that if the exhaust side is restricted excessively, the intermediate stopping accuracy will decrease and will lead to improper intermediate stops. 0 Check Valve Operating SUP side pressure P1 (MPa) Piston Cylinder pressure Operating range Cylinder pressure P2 (MPa) Check valve SUP side pressure (P1) The combination of VFS21 1 0, VFS and a double check spacer can be used as prevention of falling at the stroke end but cannot hold the intermediate position of the cylinder

9 Series VFS2000 Construction 2 position single 2 position double 3 position closed center/exhaust center/pressure center Closed center Exhaust center Pressure center Component Parts No. Description Material Note q w e Body Sub-plate Spool/Sleeve Aluminum die-casted Aluminum die-casted Stainless steel Platinum silver Platinum silver r Adapter plate Aluminum die-casted Platinum silver t End plate Resin Black y Piston Resin u Junction cover Resin i Cover Resin Sub-plate Assembly (Standard) Part No. Plug-in VFS2000-LP- 01 Non plug-in VFS2000-LS- Mounting bolt and gasket are not included. Part no. for mounting bolt and gasket BG-VFS Replacement Parts No. Description Material Part no. VFS21 VFS22 VFS23 /24 /25 o Return spring Stainless steel NVF AXT !0 Gasket NBR AXT AXT AXT !1 Hexagon socket head screw Steel AXT AXT AXT624-26!2 Detent assembly AXT624-11A!3 Pilot valve assembly Refer to How to Order Pilot Valve Assembly on page

10 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Series VFS2000 Plug-in 2 Position single/double, 3 position closed center/exhaust center/pressure center/double check 2 position single: VFS2100- F ø5 mounting hole 3-Rc, 1(P), 4(A), 2(B) bottom ported 2-Rc 3(R2), 5(R1) bottom ported G 1 2 Electrical entry 2 position double: VFS2200- F position closed center: VFS2300- F position exhaust center: VFS2400- F position pressure center: VFS2500- F (3 position: 158) 2-ø5 mounting hole 3-Rc, 2-Rc ( ): Rc 3 position double check: VFS2- F- 01 Bottom ported (External pilot port) (M5 x 0.8) Pilot EXH port M5 x ø5 mounting hole VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN (3 position: 171) ( ): Rc ( ): Rc

11 Series VFS2000 Non Plug-in 2 position single Grommet: VFS2110- G Rc, 2-ø5 mounting hole 1(P), 4(A), 2(B) bottom ported 2-Rc 3(R2), 5(R1) bottom ported Bottom ported 300 (Lead wire length) A, B 3-Rc, 2-Rc Pilot EXH port M5 x 0.8 (External pilot port M5 x 0.8) ( ): Rc Grommet terminal: VFS2110- E- 01 DIN terminal: VFS2110- D Y- 01 Lead wire O.D. Max. ø3.5 Applicable heavy-duty cord O.D. ø6 to ø8 (Y: ø4.7 to ø7) Conduit terminal: VFS2110- T- 01 Applicable heavy-duty cord O.D. ø6 to ø8 With light/surge voltage suppressor ( ): Y, YZ

12 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Series VFS2000 Non Plug-in 2 Position double, 3 position closed center/exhaust center/pressure center Grommet: Double VFS2210- G- 01 Closed center VFS2310- G- 01, Exhaust center VFS2410- G- 01, Pressure center VFS2510- G (3 position: 158) Ø5 mounting hole 3-Rc, 1(P), 4(A), 2(B) bottom ported 2-Rc 3(R2), 5(R1) bottom ported 300 (Lead wire length) Grommet terminal: Double VFS2210- E- 01 Lead wire O.D. Max. ø3.5 Closed center VFS2310- E- 01 Exhaust center VFS2410- E- 01 Pressure center VFS2510- E (3 position: 159) 3-Rc, 2-Rc Pilot EXH port M5 x 0.8 (External pilot port M5 x 0.8) Bottom ported A, B ( ): Rc DIN terminal: Double VFS2210- D Y- 01 Closed center VFS2310- D Y- 01 Exhaust center VFS2410- D Y- 01 Pressure center VFS2510- D Y- 01 VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Applicable heavy-duty cord O.D. ø6 to ø8 (Y: ø4.7 to ø7) (3 position: 195) (DZ) Conduit terminal: Double VFS2210- T- 01 Applicable heavy-duty cord O.D. ø6 to ø8 Closed center VFS2310- T- 01 Exhaust center VFS2410- T- 01 Pressure center VFS2510- T (3 position: 195) ( ): Y, YZ

13 Series VFS2000 Non Plug-in 3 position double check Grommet: VFS2610- G ø5 mounting hole 3-Rc 1/8, 1/4 1(P), 2(B), 4(A) bottom ported 2-Rc 1/8 3(R2), 5(R1) bottom ported 300 (Lead wire length) Bottom ported (External pilot port) (M5 x 0.8) Pilot EXH port M5 x 0.8 Grommet terminal: VFS2610- E- 01 DIN terminal: VFS2610- D Y- 01 Lead wire O.D. Max. ø3.5 2-Rc 3-Rc, ( ): Rc (DZ) Applicable heavy-duty code O.D. ø6 to ø8 (Y: ø4.7 to ø7) Conduit terminal: VFS2610- T- 01 ( ): Y, YZ Applicable heavy-duty code O.D. ø6 to ø

14 2.66 S OLENOID VALVES S ERIES NVFS S ERIES NVFS 2000, 3000, 4000, 5000, 0 5 PORT P ILOT O PERATED B ASE-MOUNTED / PLUG-IN T YPE Large Flow Capacity Low Power Consumption Long Life Ease Maintenance Many Variations Available For further information, consult SMC Customer Service M O D E L NVFS2000 S Y M B O L S Position Number Of Type Port Size Cv Response Solenoid Plug-In (NPTF) Factor Time (ms) Single NVFS2100 1/ or less 2 Position 1/ Double NVFS2200 1/ or less 1/ Closed NVFS2300 1/ or less Center 1/ Exhaust NVFS2400 1/ or less 3 Position Center 1/ Pressure NVFS2500 1/ or less Center 1/ Perfect NVFS2 1/ or less (Double Check) 1/4 0.4 T ECHNICAL SPECIFICATIONS S T ANDARD T ECHNICAL SPECIFICATIONS O PTIONAL Fluid Air and Inert Gas Pilot Type External Pilot Type Max Operating Pressure 150 PSI (1MPa) Manual Override Pilot Operator Non Locking Push Type (Extended), Min Operating 2 Position 15 PSI (0.1MPa) Lock Type (Tool), Lock Type (Lever) Pressure 3 Position 22 PSI (0.15MPa) Voltage AC 100V50/60Hz, 200V50/60Hz Valve Ambient & Fluid Temperature 14~140ºF (-10~60ºC) DC 6V, 48V, 100V Lubrication Not Required Porting Bottom Ported Subplate Pilot Operator Manual Override Non Locking Push Type (Flush) Option W/Indicator & Surge Protection Construction Dust Proof Voltage Suppressor Electrical Rated AC 110VAC50/60Hz, 220V50/60Hz, 24V50/60Hz Voltage DC 12V, 24V Allowable Voltage Range -15 ~ 10% Rated Voltage Coil Insulation Class B or Equivalent Apparent Power AC InRush 5.0VA/60Hz, 5.6VA/50Hz (Power Consumption) Holding 2.3VA(1.5W)/60Hz, 3.4VA(2.1W)/50Hz Power Consumption DC 1.8W Electrical Entry Plug In Conduit Terminal (Base Access) FOR FURTHER TECHNICAL DETAILS ON THIS PRODUCT, REQUEST CATALOG REFERENCE N233

15 S OLENOID VALVES S ERIES NVFS 2.67 H O W T O O R D E R NVFS2000 NVFS 2 00 F P OSITION 1 2 Position Single 2 2 Position Double 3 3 Position Closed Center 4 3 Position Exhaust Center 5 3 Position Pressure Center 6 3 Position Perfect B ODY T YPE 0 Plug-In Type P ILOT O PERATOR - Internal R External (Special Order) V OLTAGE 1 100VAC (Special Order) 2 200VAC (Special Order) 3 110VAC 4 220VAc 5 24VDC 6 12VDC 9 Others (Special Order) E LECTRICAL E NTRY F Through Base P ORT S IZE - Without Subplate 01T 1/8 NPTF T 1/4 NPTF * Bottom Ported 1/8 NPTF Only P ORTING - Side *B Bottom Note) *1/8 NPTF Only M ANUAL O VERRIDE - Non Locking Push Type (Flush) *A Non Locking Push Type (Extended) B Lock Type (Screw Type) *C Lock Type (Lever) Note) * Special Order O PTIONS - None Z With Indicator and Surge Voltage Suppressor H O W T O O R D E R M ANIFOLD S EE INSIDE FRONT COVER FOR DETAILS OF YOUR LOCAL SALES OFFICE FOR FURTHER TECHNICAL DETAILS ON THIS PRODUCT, REQUEST CATALOG REFERENCE N233