I N D E X. VQ1000 How to Order, Manifold Options VQ2000 How to Order, Manifold Options VQ1000/2000 Model, Standard/Manifold Specifications

Transcription

1 I N D E VQ000 How to Order, Manifold Options VQ000 How to Order, Manifold Options VQ000/000 Model, Standard/Manifold Specifications VQ000/000 F (D-sub connector) VQ000/000 (Flat ribbon cable) VQ000/000 J (Flat ribbon cable) VQ000/000 T (Terminal block box) VQ000/000 L (Lead wire). 0 VQ000/000 S (Serial transmission) E0 VQ000/000 S (Serial transmission) E0// VQ000/000 G (Flat ribbon cable with terminal block) VQ000 M (Circular connector) VQ000 Sub-plate Single Unit VQ000/000 Semi-standard VQ000/000 Construction VQ000/000 Exploded View of Manifold VQ000/000 Manifold Optional arts VQ000/000 Specific roduct recautions a

2 lug-in Unit ase Mounted Series -VQ000 [Option] How to Order Manifold Note) For models, DC-type only. 0 0 VVQ Clean series Copper/Fluorine/Silicon free + Low particle generation Cylinder port Series VQ000 Manifold lug-in unit 0 station 0 C The number of max. stations differs from to. (efer to the below table.) Symbol ort size Symbol ort size C C C M CM Note ) L L L With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread Mixed sizes and with port plug Top ported elbow with ø. One-touch fitting Top ported elbow with ø One-touch fitting Top ported elbow with ø One-touch fitting L LM Note ) MM Note ) Top ported elbow M thread ottom ported elbow with ø. One-touch fitting ottom ported elbow with ø One-touch fitting ottom ported elbow with ø One-touch fitting ottom ported elbow M thread Elbow port, mixed sizes Mixed size for different types of piping, option installed Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping or dual flow fitting assembly, enter MM and give instructions in the manifold specification sheet. Note ) Inch-size One-touch fittings are also available. efer to page 0 for details. Note ) M fittings for M thread are attached without being incorporated. F U Kit type Q Note) For models, DC-type only. Option Symbol Note ) D D0 D Note ) K Note ) N Note ) S Option 00/0 VC models (F/L only) With back pressure check valve DIN rail mounting With DIN rail bracket (Without DIN rail) With ejector unit Special wiring spec. (Except double wiring) With name plate External pilot Direct EH outlet with built-in silencer Note ) When two or more symbols are specified, indicate them alphabetically. Example: -S Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) Specify the wiring specifications by means of the manifold specification sheet. (Except L ) Note ) Indicate for the valve with external pilot. Note ) : Station. Example: D0: The number of stations that may be displayed is longer than the manifold number of stations. Simple specials are available with SMC Simple Specials System. efer to est neumatics No. q for details on applicable models. Kit type/electrical entry/cable length F (D-sub connector) Top entry (Flat ribbon cable) Top entry J (Flat ribbon cable 0) Top entry G (Flat ribbon cable with terminal block) The voltage used for the valve is VDC. Note ) Note ) 0 0 Order separately SI unit made by OMON Corp. Connector entry direction Top entry Side entry F U0 U U U F S0 S S S Side entry. 0 Without cable With cable (. m) With cable ( m) With cable ( m) Note ) to stations Connector entry direction Top entry Side entry U0 U U U S0 S S S Without cable With cable (. m) With cable ( m) With cable ( m) Side entry Note ) to stations Connector entry direction U0 U U U S0 S S S Side entry.. Top entry Side entry Note ) esides the above, F/ with different number of pins are available. efer to page for details. Note ) efer to page 9 for details. J J Without cable With cable (. m) With cable ( m) With cable ( m) Note ) to stations G 0 Without cable With cable (. m) With cable ( m) With cable ( m). Note ) to stations

3 How to Order Valves ase Mounted lug-in Unit Series -VQ000 Note) For models, DC-type only. [Option] How to Order Manifold ssembly 0 0 VQ 0 0 Series VQ000 Clean series Copper/Fluorine/Silicon free + Low particle generation Seal 0 Metal seal ubber seal : Non-locking push type (Tool required) Q Note) For models, DC-type only. Manual override : Locking type (Tool required) Example Single solenoid ( VDC) VQ00- ( sets) m D side U side VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- Double solenoid ( VDC) VQ00- ( sets) lanking plate VVQ000- ( set) VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VVQ000- VVQ000- VQ00- Type of actuation -position single ubber Metal -position double -position double -position closed center -position exhaust center -position pressure center Symbol Specifications K Note ) N Note ) Note ) Standard High-speed response type High-pressure type (.0 Ma) Negative common External pilot Function DC C (0. W) (0.9 W) (0.9 W) Note ) Note ) efer to page 9 for power consumption of C type. Note ) Metal seal only Note ) For external pilot and negative common specifications, refer to Semi-standard on pages 9 to 0. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. C: Locking type (Manual) Light/surge voltage suppressor E Note) Yes Note) Not applicable to the S. Coil voltage 00 VC (0/0 Hz) Note) 00 VC (0/0 Hz) 0 VC (0/0 Hz) Note) 0 VC (0/0 Hz) VDC VDC Note) 00 and 0 VC: F/L only D: Slide locking type (Manual) D-sub connector cable assembly T00-DS-00 F (D-sub connector) VVQ-09CFU VQ00- VQ00- VVQ000- Cylinder port fitting port size C: With ø One-touch fitting Manifold base (9 stations) VVQ-09CFU set (F 9-station manifold base part no.) sets (Single solenoid part no.) sets (Double solenoid part no.) set (lanking plate part no.) The asterisk denotes the symbol for assembly. refix it to the part nos. of the solenoid valve, etc. Specify the part numbers for valves and options together beneath the manifold base part number. esides, when the arrangement will be complicated, specify them by means of the manifold specification sheet. Caution Use the standard (DC) specification when continuously energizing for long periods of time. T (Terminal block box). T O Terminal block box to stations Note ) L L (Lead wire) 0 With cable (0. m) With cable (. m) With cable ( m). 0 to stations S (Serial transmission) S 0 F H J J Q V Z ZN Without SI unit NKE Corp.: Fieldbus System NKE Corp.: Fieldbus H System SUN Corp.: S-LINK ( outputs) SUN Corp.: S-LINK ( outputs) DeviceNet OMON Corp.: Compous/S ( outputs) OMON Corp.: Compous/S ( outputs) CC-LINK CompoNet (ositive common) CompoNet (Negative common) The valve is equipped with an indicator light and surge voltage suppressor, and the voltage is VDC. The dust proof SI unit is also available. efer to page for details. Note) efer to SI Unit art No. on page when ordering the CE-compliant SI unit.. Note ) Max. stations Max. stations Max. stations Max. stations Max. stations a

4 0 0 station The maximum and minimum number of stations are varied depending on. (efer to the below table.) Connector entry direction Top entry Side entry U0 U U U S0 S S S VVQ VQ000 Manifold lug-in unit Cylinder port 0 C F U Kit type Symbol ort size Symbol ort size C C C L CM Note ) L L Series With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting Mixed sizes and with port plug Top ported elbow with ø One-touch fitting Top ported elbow with ø One-touch fitting Kit type/electrical entry/cable length F Note ) F T T (D-sub connector) F. 0 Without cable With cable (. m) With cable ( m) With cable ( m) (Terminal block box) Dust-tight/Water-jet-proof (I) compatible 0 Clean series Copper/Fluorine/ Silicon free + Low particle generation. Note ) to stations O Terminal block box to 0 stations Note ) U0 U U U L S0 S S S (Lead wire) Dust-tight/Water-jet-proof (I) compatible L 0 LM Note ) MM Note ) Simple specials are available with SMC Simple Specials System. efer to est neumatics No. q for details on applicable models. Top entry Connector entry direction Top entry Side entry (Flat ribbon cable) Without cable With cable (. m) With cable ( m) With cable ( m). 0 With cable (0. m) With cable (. m) With cable ( m) to stations Top ported elbow with ø One-touch fitting ottom ported elbow with ø One-touch fitting ottom ported elbow with ø One-touch fitting ottom ported elbow with ø One-touch fitting Elbow port, mixed sizes Mixed size for different types of piping, option installed.. Note ) to stations Note ) esides the above, F/ with different number of pins are available. efer to page for details. Note ) efer to page 9 for details. S S J Connector entry direction Top entry Side entry J U0 U U U (Flat ribbon cable 0) J S0 S S S Without cable With cable (. m) With cable ( m) With cable ( m) (Serial transmission) Option Symbol Note ) D D0 Note ) to stations D Note ) K Note ) N Note ) Max. stations Max. stations Max. stations Max. stations M 0 Option 00/0 VC models (F/L only) With back pressure check valve DIN rail mounting With DIN rail bracket (Without DIN rail) DIN rail length specified Special wiring spec. (Except double wiring) With name plate External pilot G (Flat ribbon cable with terminal block) G The valve is equipped with an indicator light and surge voltage suppressor, and the voltage is VDC. The dusttight SI unit is available. efer to page for details. Dust-tight, Waterjet-proof (I) is available. Note) efer to SI Unit art No. on page when. ordering the CE-compliant SI unit. 0 Without SI unit Note ) F NKE Corp.: Fieldbus System Max. H NKE Corp.: Fieldbus H System stations J SUN Corp.: S-LINK ( outputs) J Q SUN Corp.: S-LINK ( outputs) DeviceNet OMON Corp.: Compous/S ( outputs) OMON Corp.: Compous/S ( outputs) V CC-LINK Q Note) For models, DC-type only. Note ) Indicate Mixed size and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size One-touch fittings are also available. efer to page 0 for details. Side entry lug-in Unit ase Mounted Series Note ) Top entry -VQ000 How to Order Manifold Side entry 0 Top entry Side entry Note ) When two or more symbols are specified, indicate them alphabetically. Example: -DN Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) Specify the wiring specifications by means of the manifold specification sheet. (Except L ) Note ) Indicate for the valve with external pilot. Note ) : Station. Example: D0: The number of stations that may be displayed is longer than the manifold number of stations. Note ) U0 U U U M Without cable With cable (. m) With cable ( m) With cable ( m) The voltage used for the valve is VDC.. (Circularconnector). Without cable With cable (. m) With cable ( m) With cable ( m) [Option] Note) For models, DC-type only. Note ) to stations Note ) to stations Note ) efer to the pages on respective s for I type. (T/L/S ) Note ) Serial transmission system with I enclosure applicable to input/output is also available. efer to page for details.

5 How to Order Valves ase Mounted lug-in Unitt Series -VQ000 Note) For models, DC-type only. [Option] How to Order Manifold ssembly 0 0 VQ 0 0 Series VQ000 Type of actuation -position single Metal ubber Clean series Copper/Fluorine/Silicon free + Low particle generation -position double -position double -position closed center -position exhaust center -position pressure center Note) For sub-plate single unit type, refer to page 7. 0 Seal Metal seal ubber seal Light/surge voltage suppressor E Note) Yes Coil voltage 00 VC (0/0 Hz) Note) 00 VC (0/0 Hz) 0 VC (0/0 Hz) Note) 0 VC (0/0 Hz) VDC VDC Q Note) For models, DC-type only. Enclosure Dust-tight/water-jetproof type W Note) (I) Note) T, L, S and M s only Note) Not applicable to the S. Note) 00 and 0 VC: F/L only Manual override : Non-locking push type (Tool required) Example Single solenoid ( VDC) VQ00- ( sets) m D-sub connector cable assembly T00-DS-00 VVQ-0CFU VQ00- VQ00- VVQ000- Double solenoid ( VDC) VQ00- ( sets) F (D-sub connector) VVQ000- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- D side U side lanking plate VVQ000- ( set) Cylinder port fitting port size C: With ø One-touch fitting Manifold base ( stations) VVQ-0CFU set (F -station manifold base part no.) sets (Single solenoid part no.) sets (Double solenoid part no.) set (lanking plate part no.) The asterisk denotes the symbol for assembly. refix it to the part nos. of the solenoid valve, etc. Specify the part numbers for valves and options together beneath the manifold base part number. esides, when the arrangement will be complicated, specify them by means of the manifold specification sheet. Symbol Specifications Function DC C : ush-locking slotted type (Tool required) Standard (0. W) Note ) K Note ) N Note ) Note ) High-speed response type High-pressure type (.0 Ma) Negative common External pilot (0.9 W) (0.9 W) Note ) For power consumption of C type, refer to page 9. Note ) Metal seal only Note ) For external pilot and negative common specifications, refer to Semi-standard on pages 9 to 0. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. C: Locking type (Manual) D: Slide locking type (Manual) Caution Use the standard (DC) specification when continuously energizing for long periods of time. a

6 7 7 Series -VQ000 -VQ000: Manifold Options. to 9 lanking plate assembly VVQ000- Individual SU spacer VVQ C N7 Individual EH spacer VVQ C N7 SU block plate VVQ000- EH block base assembly VVQ F C, C C, M N, N L N7 C (SU port) ø One-touch fitting C (EH port) ø One-touch fitting ack pressure check valve assembly [-] VVQ000- Name plate [-N] VVQ000- N NC-Station ( to Max. stations) lanking plug KQ- DIN rail mounting bracket [-D/-D0/-D ] VVQ VQ000: Manifold Options. 0 to lanking plate assembly VVQ000- Individual SU spacer VVQ C N9 Individual EH spacer VVQ C N9 SU block plate VVQ000- EH block plate VVQ000-9 C (SU port) ø One-touch fitting C (EH port) ø One-touch fitting ack pressure check valve assembly [-] VVQ000- Name plate [-N] VVQ000-N-Station ( to Max. stations) lanking plug KQ- DIN rail mounting bracket [-D/-D0/-D ] VVQ000-7

7 lug-in Unit ase Mounted Series -VQ000/000 Model Series VQ000 VQ000 -position -position -position -position Type of actuation Single Double Closed center Exhaust center ressure center Single Double Closed center Exhaust center ressure center Metal seal ubber seal Metal seal ubber seal Metal seal ubber seal Metal seal ubber seal Metal seal ubber seal Metal seal ubber seal Metal seal ubber seal Metal seal ubber seal Metal seal ubber seal Metal seal ubber seal Model -VQ00 -VQ0 -VQ00 -VQ0 -VQ00 -VQ0 -VQ00 -VQ0 -VQ00 -VQ0 -VQ00 -VQ0 -VQ00 -VQ0 -VQ00 -VQ0 -VQ00 -VQ0 -VQ00 -VQ0 Flow-rate characteristics Note ) / ( /) / / (/ /) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv Standard: 0. W or less 0 or less or less 0 or less or less or less or less or less or less or less 9 or less or less 0 or less or less or less or less or less or less or less or less Note ) The values are given for port size C: (VQ000), C: (VQ000) without back pressure check valve. Note ) s per JIS 7-9 (Supply pressure 0. Ma; with indicator light/surge voltage suppressor; clean air The response time is subject to the pressure and quality of the air.) The values at the time of ON are given for double types. esponse time (ms) Note ) High-speed response: 0.9 W or less or less 0 or less or less 0 or less or less 0 or less or less 0 or less or less or less or less or less 0 or less 9 or less or less 9 or less or less 9 or less or less C 9 or less or less or less 0 or less 0 or less 7 or less 0 or less 7 or less 0 or less 7 or less 9 or less or less 0 or less or less or less or less or less or less or less or less Mass (g)

8 ase Mounted lug-in Unit Series -VQ000/000 JIS symbol -position single Metal ubber -position double -position double -position closed center -position exhaust center -position pressure center Manifold Specifications Series - VQ000 - VQ000 ase model VVQ- VVQ- Standard Specifications Connection type F D-sub connector Flat ribbon cable J Flat ribbon cable (0) G Flat ribbon cable with terminal block T Terminal block box L Lead wire S Serial transmission F D-sub connector Flat ribbon cable J Flat ribbon cable (0) G Flat ribbon cable with terminal block T Terminal block box L Lead wire S Serial transmission M Circular connector Valve type Fluid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Lubrication Manual override Impact/Vibration resistance Note ) Enclosure Coil rated voltage llowable voltage fluctuation Coil insulation type ower consumption (Current) iping direction Side Side Note ) Inch-size one-touch fittings are also available. efer to page 0 for details. Note ) efer to page 9 for details. Valve specifications Electrical specifications Single Double -position -position VDC VDC 00 VC 0 VC 00 VC 0 VC iping specifications ort size Note ) (), () C (ø) Option: Direct EH outlet with built-in silencer C0 (ø0) Option: Direct EH outlet with built-in silencer Metal seal ir, Inert gas 0.7 Ma (High-pressure type:.0 Ma) 0. Ma 0. Ma 0. Ma 0 to 0 C Note ) Not required ush type, Locking type (Tool required, Manual) semi-standard 0/0 m/s Dust-protected; Dust-tight, Water-jet-proof (I) Note ), VDC, 00, 0, 00, 0 VC (0/0 Hz) ±0% of rated voltage Equivalent to Class ubber seal ir, Inert gas 0.7 Ma 0. Ma 0. Ma 0. Ma 0. Ma 0. W DC (7 m), 0.9 W DC (0 m) Note ) 0. W DC ( m), 0.9 W DC (0 m) Note ) Inrush 0.9 V (0 m), Holding 0.9 V (0 m) Inrush.0 V (9 m), Holding.0 V (9 m) Inrush. V ( m), Holding. V ( m) Inrush. V ( m), Holding. V ( m) Note ) Use dry air to prevent condensation when operating at low temperatures. Note ) Impact resistance No malfunction occurred when it is tested in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance No malfunction occurred in a one-sweep test between and 000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Note ) Value for high-speed response, high-voltage type (0.9 W) Note ) Dust-tight, Water-jet-proof (I) is available on T/L/S/M of the VQ000. (), () C (ø.) C(ø) C (ø) M (M thread) C (ø) C (ø) C (ø) Note ) pplicable stations F//T to stations J/G/S to stations L to stations F/ to stations J/G/S to stations L to stations T to 0 stations pplicable solenoid valve VQ 00 VQ 0 VQ 00 VQ 0 -station mass (g) (Single) 7 (Double, -position) 07 (Single) 9 (Double, -position) port port port port Type of connection, port Type of connection, port -VVQ - VVQ 9 a

9 F Series -VQ000/000 Kit (D-sub connector) - VVQ - VVQ D-sub connector reduces installation labor for electrical connections. Using the D-sub connector (), ( as semi-standard) conforming to MIL standard permits the use of connectors put on the market and gives a wide interchangeability. Top or side receptacle position can be selected in accordance with the available mounting space. Maximum stations are. D-sub Connector ( ins) Manifold Specifications Series - VQ000 - VQ000 iping direction Side Side iping specifications (), () C C0 ort size (), () C, C, C, M C, C, C pplicable stations Max. stations Max. stations Cable ssembly T00-DS The D-sub connector cable assembly can be ordered individually or included in a specific manifold model no. efer to How to Order Manifold. L 7.0 Multi-core vinyl cable 0. mm x cores ø0 x M. x 0. Socket side Terminal no. D-sub connector cable assembly Cable length (L). m m m ssembly part no. T00-DS-0 T00-DS-00 T00-DS-00 Note ) Types with pins are also available. efer to page for details. Note ) Lengths other than the above are also available. lease contact SMC for details. Note Cable cores x WG For other commercial connectors, use a pins type with female connector conforming to MIL-C-0. Cannot be used for transfer wiring. Connector manufacturers example Fujitsu Limited Japan viation Electronics Industry, Ltd. J.S.T. Mfg. Co., Ltd. Hirose Electric Co., Ltd. Electrical characteristics Item Conductor resistance Ω/km, 0 C Voltage limit V, min, C Insulation resistance MΩ/km, 0 C roperty or less 000 or more Note) The min. bending radius of the D-sub connector cable assembly is 0 mm. Wire color by terminal no. of D-sub connector cable assembly Terminal no. Lead wire color Dot marking lack rown ed Orange Yellow ink lue urple Gray Yellow Orange Yellow ink lue urple Gray Orange ed rown ink Gray lack lack lack ed ed ed lack lack lack ed ed How to Order Manifold a stations VVQ 0 C F U Clean series Copper/Fluorine/Silicon free + Low particle generation Series VQ000 VQ000 stations Manifold lug-in unit Note) efer to page 9 for details. Connector entry U S Cylinder port Symbol C Note ) C Note ) C Note ) C Note ) M CM Note ) Note ) MM Note ) direction Top entry Side entry ort size With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread Mixed sizes and with port plug Mixed size for different types of piping, option installed Q Note) For models, DC-type only. Cable (Length) 0 Without cable With cable (. m) With cable ( m) With cable ( m) VQ000 VQ000 Option Symbol Note ) D D0 D Note ) K Note ) N Note ) Note ) Insert L (Top ported) or (ottom ported) for elbow type. Example) (ottom ported elbow with ø One-touch fitting) Note ) Indicate LM for models with elbow fittings and mixed cylinder port sizes. Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size One-touch fittings are available. efer to Semi-standard on page 0 for details. Note) For models, DC-type only. Option 00/0 VC models (F/L only) With back pressure check valve DIN rail mounting With DIN rail bracket (Without DIN rail) DIN rail length specified ( : 0 to ) [Option] Special wiring specifications (Except double wiring) With name plate External pilot Note ) When two or more symbols are specified, indicate them alphabetically. Example) -S Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) The number of stations that may be displayed is longer than the manifold number of stations. Note ) Specify the wiring specifications by means of the manifold specification sheet. Note ) Indicate for the valve with external pilot.

10 ase Mounted lug-in Unit Series -VQ000/000 D side U side D side U side The total number of stations is tabulated starting from station one on the D-side. - VVQ - VVQ Electrical Wiring Specifications D-sub connector Connector terminal no. s the standard electrical wiring specifications, double wiring (connected to SOL. and SOL. ) is adopted for the internal wiring of each station for stations or less, regardless of valve and option types. Mixed single and double wiring is available as semi-standard. efer to page 9 for details. Station Station Station Station Station Station Station 7 Station Station 9 Station 0 Station Station SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. COM. Terminal no. Note) When using the negative common specifications, use valves for negative common. (efer to page 9.) efer to Semi-standard on page 9 for details ositive COM spec. olarity D-sub connector assembly 0 T00-DS- 00 Wire color 00 Note) Negative COM spec. Lead wire color lack Yellow rown ink ed lue Orange urple Yellow Gray ink Orange lue ed urple rown Gray ink Gray lack Yellow Orange Dot marking lack lack lack lack ed lack ed ed ed ed How to Order Valves 0 0 Series VQ000 VQ000 Type of actuation 0 VQ 0 0 Clean series Copper/Fluorine/Silicon free + Low particle generation -position single -position double -position closed center -position exhaust center -position pressure center Seal Metal seal ubber seal Function Symbol Specifications K Note ) N Note ) Note ) Standard High-speed response type High-pressure type (.0 Ma) Negative common External pilot DC (0. W) (0.9 W) (0.9 W) Note) For models, DC-type only. C Note ) Note ) efer to page 9 for power consumption of C type. Note ) Metal seal only Note ) For external pilot and negative common specifications, refer to Semi-standard on pages 9 to 0. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. Manual override C D Non-locking push type (Tool required) Locking type (Tool required) Locking type (Manual) Slide locking type (Manual) Light/surge voltage suppressor E Q Note) For models, DC-type only. Yes [Option] Coil voltage 00 VC (0/0 Hz) 00 VC (0/0 Hz) 0 VC (0/0 Hz) 0 VC (0/0 Hz) VDC VDC How to Order Manifold ssembly Specify the part numbers for valves and options together beneath the manifold base part number. <Example> D-sub connector with cable ( m) VVQ-09CFU VQ00- VQ00- VQ00- VVQ000- refix the asterisk to the part nos. of the solenoid valve, etc. m set Manifold base part no. sets Valve part no. ( to ) sets Valve part no. ( to ) sets Valve part no. ( 7 to ) set lanking plate part no. (Station 9) Write sequentially from the st station on the D-side. When part nos. written collectively are complicated, specify them by means of the manifold specification sheet. D side U side Caution Use the standard (DC) specification when continuously energizing for long periods of time. VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VVQ000-

11 F Series -VQ000/000 (D-sub connector) -VVQ < >: C The dashed lines indicate the DIN rail mounting [-D] and the side entry connection [-FS]. () pplicable connector: D-sub connector () (Complies with MIL-C-0). <7.>.. (L) (L) L L = 0. Indicator light 7 Manual override (.) 9. <00.> 0. (). [] [ ]: pins (top entry) D side 7 n C [() EH port] C: ø One-touch fitting 9. (.) () M mounting hole U side DIN rail clamp screw 0.7 (7.) C, C, C, M [(), () port] C: ø. One-touch fitting C: ø One-touch fitting C: ø One-touch fitting M: M thread. = 0.. C [() SU port] C: ø One-touch fitting Dimensions L n L L (L) (L) With ejector unit: Formula L = 0.n (Number of ejector units x.7) L = 0.n +. + (Number of ejector units x.7) L is L plus about Formula L = 0.n +., L = 0.n n: Station (Maximum stations) a

12 ase Mounted lug-in Unit Series -VQ000/000 -VVQ < >: C The dashed lines indicate the DIN rail mounting [-D] and the side entry connection [-FS]. pplicable connector: D-sub connector () (Complies with MIL-C-0) () 7. <77.>.. (L) Indicator light (L) (.) L L = 0.9. Manual override. 0 <.9> 0 () (.) x M mounting hole D side 7 n U side C0 [() EH port] C0: ø0 One-touch fitting EH EH DIN rail clamp screw C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting = C0 [() SU port] C0: ø0 One-touch fitting (7.) () Dimensions L n L L (L) (L) Formula L = n +, L = n n: Station (Maximum stations) a

13 Series -VQ000/000 (Flat ribbon cable) - VVQ - VVQ MIL flat ribbon cable connector reduces installation labor for electrical connection. Using the connector for flat ribbon cable () conforming to MIL standard permits the use of connectors put on the market and gives a wide interchangeability. Top or side receptacle position can be selected in accordance with the available mounting space. Maximum stations are. Flat ibbon Cable ( ins) Cable ssembly Manifold Specifications Series - VQ000 - VQ000 iping direction Side Side iping specifications (), () C C0 ort size D side U side (), () C, C, C, M C, C, C pplicable stations Max. stations Max. stations T00-FC- to Flat ribbon cable connector assembly can be ordered individually or included in a specific manifold model no. efer to How to Order Manifold. ed - VVQ Terminal no. Flat ibbon Cable Connector ssembly Cable length (L). m m m ssembly part no. T00-FC- T00-FC- T00-FC- Note Cable cores x WG For other commercial connectors, use a pins type with strain relief conforming to MIL-C-0. Cannot be used for transfer wiring. Connector manufacturers example Hirose Electric Co., Ltd. Sumitomo M Limited Fujitsu Limited Japan viation Electronics Industry, Ltd. J.S.T. Mfg. Co., Ltd. Oki Electric Cable Co., Ltd. Note ) Other than the above model, 0,, 0 are also available. efer to page for details. Note ) Lengths other than the above are also available. lease contact SMC for details. D side U side - VVQ The total number of stations is tabulated starting from one on the D-side. How to Order Manifold 0 a 0 VVQ 0 C U Clean series Copper/Fluorine/Silicon free + Low particle generation 0 stations Series VQ000 VQ000 Manifold lug-in unit stations Note) efer to page 9 for details. Symbol C Note ) C Note ) C Note ) C Note ) M CM Note ) Note ) MM Note ) Connector entry direction U S Cylinder port Top entry Side entry ort size With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread Mixed sizes and with port plug Mixed size for different types of piping, option installed VQ000 VQ000 Cable (Length) 0 Without cable With cable (. m) With cable ( m) With cable ( m) Note ) Insert L (Top ported) or (ottom ported) for elbow type. Example) (ottom ported elbow with ø One-touch fitting) Note ) Indicate LM for models with elbow fittings and mixed cylinder port sizes. Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size one-touch fittings are available. efer to Semi-standard on page 0 for details. Q Note) For models, DC-type only. Note) For models, DC-type only. Option Symbol Note ) D D0 D Note ) K Note ) N Note ) Option [Option] With back pressure check valve DIN rail mounting With DIN rail bracket (Without DIN rail) DIN rail length specified ( : 0 to ) Special wiring specifications (Except double wiring) With name plate External pilot Note ) When two or more symbols are specified, indicate them alphabetically. Example) -S Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) The number of stations that may be displayed is longer than the manifold number of stations. Note ) Specify the wiring specifications by means of the manifold specification sheet. Note ) Indicate for the valve with external pilot.

14 ase Mounted lug-in Unit Series -VQ000/000 Electrical Wiring Specifications Flat ribbon cable connector Connector terminal no. Triangle mark indicator position Station Station Station Station Station Station Station 7 Station Station 9 Station 0 Station Station SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. COM. COM. Terminal no Electrical wiring specifications ositive COM spec. olarity Note) Negative COM spec. s the standard electrical wiring specifications, double wiring (connected to SOL. and SOL. ) is adopted for the internal wiring of each station for stations or less, regardless of valve and option types. Mixed single and double wiring is available as semi-standard. efer to page 9 for details. Note) When using the negative common specifications, use valves for negative common. (efer to page 9.) efer to Semi-standard on page 9 for details. How to Order Valves 0 0 VQ 0 0 Series VQ000 VQ000 Clean series Copper/Fluorine/Silicon free + Low particle generation Type of actuation -position single -position double -position closed center -position exhaust center -position pressure center 0 Seal Metal seal ubber seal Caution Use the standard (DC) specification when continuously energizing for long periods of time. Function Symbol Specifications K Note ) N Note ) Note ) Standard High-speed response type High-pressure type (.0 Ma) Negative common External pilot DC (0. W) (0.9 W) (0.9 W) Note) For models, DC-type only. Manual override C D Non-locking push type (Tool required) Locking type (Tool required) Locking type (Manual) Slide locking type (Manual) Light/surge voltage suppressor E C Note ) Yes Coil voltage [Option] Q Note) For models, DC-type only. 00 VC (0/0 Hz) 0 VC (0/0 Hz) VDC VDC How to Order Manifold ssembly Specify the part numbers for valves and options together beneath the manifold base part number. <Example> Flat ribbon cable with cable ( m) VVQ-09CU VQ00- VQ00- VQ00- VVQ000- refix the asterisk to the part nos. of the solenoid valve, etc. m Note ) efer to page 9 for power consumption of C type. Note ) Metal seal only Note ) efer to Semi-standard on pages 9 to 0 for external pilot and negative common specifications. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. set Manifold base part no. sets Valve part no. ( to ) sets Valve part no. ( to ) sets Valve part no. ( 7 to ) set lanking plate part no. (Station 9) Write sequentially from the st station on the D-side. When part nos. written collectively are complicated, specify them by means of the manifold specification sheet. D side U side VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VVQ000-

15 Series -VQ000/000 (Flat ribbon cable) -VVQ < >: C The dashed lines indicate the DIN rail mounting [-D] and the side entry connection [-S]. pplicable connector: Flat ribbon cable connector () (Complies with MIL-C-0) (). <7.>... (L) (L) L L = 0. Indicator light 7 Manual override (.) <00.> () (.) (). M mounting hole. D side 7 n U side C [() EH port] C: ø One-touch fitting DIN rail clamp screw (7.) C, C, C, M [(), () port] C: ø. One-touch fitting C: ø One-touch fitting C: ø One-touch fitting M: M thread = 0... C [() SU port] C: ø One-touch fitting Dimensions L n L L (L) (L) With ejector unit: Formula L = 0.n (Number of ejector units x.7) L = 0.n +. + (Number of ejector units x.7) L is L plus about Formula L = 0.n +., L = 0.n n: Station (Maximum stations) a

16 ase Mounted lug-in Unit Series -VQ000/000 -VVQ < >: C The dashed lines indicate the DIN rail mounting [-D] and the side entry connection [-S]. pplicable connector: Flat ribbon cable connector () (Complies with MIL-C-0) () 7. <77.>. Indicator light L L. = 0.9. Manual override 0 <.9> 0 () (.) (L) (L) x M mounting hole (.) Flat ribbon cable connector assembly () T00-FC-:. m T00-FC-: m T00-FC-: m D side 7 n U side EH C0 [() EH port] C0: ø0 One-touch fitting EH DIN rail clamp screw C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting = C0 [() SU port] C0: ø0 One-touch fitting (7.) () Dimensions L n L L (L) (L) Formula L = n +, L = n n: Station (Maximum stations) a

17 J Series -VQ000/000 (Flat ribbon cable) - VVQ - VVQ MIL flat ribbon cable connector reduces installation labor for electrical connection. Using the connector for flat ribbon cable connectors (0) conforming to MIL standard permits the use of connector put on the market and gives a wide interchangeability. Top or side receptacle position can be selected in accordance with the available mounting space. Maximum stations are. Flat ibbon Cable (0 ins) Manifold Specifications Series - VQ000 - VQ000 Cable ssembly iping direction Side Side iping specifications (), () C C0 ort size D side U side (), () C, C, C, M C, C, C pplicable stations Max. stations Max. stations T00-FC0- to Flat ribbon cable connector assembly can be ordered individually or included in a specific manifold model no. efer to How to Order Manifold. ed - VVQ Terminal no. Flat ibbon Cable Connector ssembly Cable length (L). m m m ssembly part no. T00-FC0- T00-FC0- T00-FC0- Note Cable 0 cores x WG For other commercial connectors, use a 0 pins with strain relief conforming to MIL-C-0. Cannot be used for transfer wiring. Connector manufacturers example Hirose Electric Co., Ltd. Sumitomo M Limited Fujitsu Limited 0 stations Series VQ000 VQ000 Manifold lug-in unit stations Japan viation Electronics Industry, Ltd. J.S.T. Mfg. Co., Ltd. Oki Electric Cable Co., Ltd. Note) Lengths other than the above are also available. lease contact SMC for details. How to Order Manifold a 0 0 VVQ 0 C J U Clean series Copper/Fluorine/Silicon free + Low particle generation Note) efer to page 9 for details. Connector entry direction Symbol C Note ) C Note ) C Note ) C Note ) M CM Note ) Note ) MM Note ) U S Cylinder port Top entry Side entry ort size With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread Mixed sizes and with port plug Mixed size for different types of piping, option installed Cable (Length) 0 Without cable With cable (. m) With cable ( m) With cable ( m) VQ000 VQ000 Note ) Insert L (Top ported) or (ottom ported) for elbow type. Example) (ottom ported elbow with ø One-touch fitting) Note ) Indicate LM for models with elbow fittings and mixed cylinder port sizes. Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size One-touch fittings are available. efer to Semi-standard on page 0 for details. The total number of stations is tabulated starting from one on the D-side. Q D side U side Option Symbol Note ) D D0 D Note ) K Note ) N Note ) Option - VVQ [Option] With back pressure check valve DIN rail mounting With DIN rail bracket (Without DIN rail) DIN rail length specified ( : 0 to ) Special wiring specifications (Except double wiring) With name plate External pilot Note ) When two or more symbols are specified, indicate them alphabetically. Example) - S Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) The number of stations that may be displayed is longer than the manifold number of stations. Note ) Specify the wiring specifications by means of the manifold specification sheet. Note ) Indicate for the valve with external pilot.

18 ase Mounted lug-in Unit Series -VQ000/000 Electrical Wiring Specifications Flat ribbon cable connector Connector terminal no Triangle mark indicator position Station Station Station Station Station Station Station 7 Station Terminal no. SOL. 0 SOL. SOL. SOL. SOL. SOL. 0 SOL. SOL. SOL. 9 SOL. 7 SOL. SOL. SOL. SOL. 9 SOL. 7 SOL. olarity s the standard electrical wiring specifications, double wiring (connected to SOL. and SOL. ) is adopted for the internal wiring of each station for stations or less, regardless of valve and option types. Mixed single and double wiring is available as semi-standard. efer to Semi-standard on page 9 for details. Note) When using the negative common specifications, use valves for negative common. (efer to page 9,) efer to Semi-standard on page 9 for details. COM. COM. ositive COM spec. Note) ositive COM spec. How to Order Valves 0 0 VQ 0 0 Series VQ000 VQ000 Clean series Copper/Fluorine/Silicon free + Low particle generation Type of actuation -position single -position double -position closed center -position exhaust center -position pressure center 0 Seal Metal seal ubber seal Function Symbol Specifications K Note ) N Note ) Note ) Standard High-speed response type High-pressure type (.0 Ma) Negative common External pilot Manual override C D Non-locking push type (Tool required) Locking type (Tool required) Locking type (Manual) Slide locking type (Manual) Light/surge voltage suppressor E DC (0. W) (0.9 W) Yes Q Coil voltage VDC [Option] (0.9 W) Note ) Metal seal only Note ) efer to Semi-standard on pages 9 to 0 for external pilot and negative common specifications. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. How to Order Manifold ssembly Specify the part numbers for valves and options together beneath the manifold base part number. <Example> Flat ribbon cable with cable ( m) VVQ-0CJU VQ00- VQ00- VQ00- VVQ000- refix the asterisk to the part nos. of the solenoid valve, etc. m set Manifold base part no. sets Valve part no. ( to ) sets Valve part no. ( to ) set Valve part no. (Station 7) set lanking plate part no. (Station ) D side U side Write sequentially from the st station on the D-side. When part nos. written collectively are complicated, specify them by means of the manifold specification sheet. 9

19 t y p e J Series -VQ000/000 (Flat ribbon cable) -VVQ The dashed lines indicate the DIN rail mounting [-D] and the side entry connection [-JS]. pplicable connector: Flat ribbon cable connector (0) (Complies with MIL-C-0) ()..... (L) (L) L L = 0. Indicator light 7 Manual override (.) () (.). D side 7 n x M mounting hole U side C [() EH port] C: ø One-touch fitting DIN rail clamp screw () (7.) C, C, C, M [(), () port] C: ø. One-touch fitting C: ø One-touch fitting C: ø One-touch fitting M: M thread = 0... C [() SU port] C: ø One-touch fitting Dimensions L n L L (L) (L) With ejector unit: Formula L = 0.n (Number of ejector units x.7) L = 0.n +. + (Number of ejector units x.7) L is L plus about Formula L = 0.n +., L = 0.n + 7. n: Station (Maximum stations) a 0

20 ase Mounted lug-in Unit Series -VQ000/000 -VVQ The dashed lines indicate the DIN rail mounting [-D] and the side entry connection [-JS]. pplicable connector: Flat ribbon cable connector (0) (Complies with MIL-C-0) () 7.. L L.. Indicator light = 0.9. Manual override CW type 0 0 () (.) (L) (.) (L) x M mounting hole D side 7 n U side C0 [() EH port] C0: ø0 One-touch fitting EH EH DIN rail clamp screw C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting = C0 [() SU port] C0: ø0 One-touch fitting (7.) () Dimensions L n L L (L) (L) Formula L = n +, L = n + n: Station (Maximum stations)

21 G Series -VQ000/000 (Flat ribbon cable with terminal block) - VVQ - VVQ Terminal block for power supply equipped with a 0 pins flat ribbon cable connection for rationalized connection of valves. Solenoid valves and power supply can be connected by the same cable to a specific output unit that requires power supply from the output section to the internal circuit. Maximum stations are. Manifold Specifications Series - VQ000 - VQ000 iping direction Side Side iping specifications (), () C C0 ort size (), () C, C, C, M C, C, C pplicable stations Max. stations Max. stations Flat ibbon Cable (0 ins) Cable ssembly T00-FC0- to Flat ribbon cable connector assembly can be ordered individually or included in a specific manifold model no. efer to How to Order Manifold. U side D side The total number of stations is tabulated starting from station one on the D-side. ed ower supply terminal block (Terminal screw M) Indicator light Terminal no. Flat ibbon Cable Connector ssembly Cable length (L). m m m ssembly part no. T00-FC0- T00-FC0- T00-FC0- Note Cable 0 cores x WG For other commercial connectors, use a 0 pins type with strain relief conforming to MIL-C-0. Cannot be used for transfer wiring. Connector manufacturers example Hirose Electric Co., Ltd. Japan viation Electronics Sumitomo M Limited Industry, Ltd. J.S.T. Mfg. Co., Ltd. Oki Electric Cable Co., Ltd. Fujitsu Limited Note) Lengths other than the above are also available. lease contact SMC for details. - VVQ D side D side SI unit made by OMON Corp. Mountable for G7-OD (Order separately) - VVQ How to Order Manifold a 0 0 Series VQ000 VQ000 0 Note) VVQ 0 C G Clean series Copper/Fluorine/Silicon free + Low particle generation stations stations Note) efer to page 9 for details. Manifold lug-in unit Connector entry direction, Top entry U Cylinder port Symbol C Note ) C Note ) C Note ) C Note ) M CM Note ) Note ) MM Note ) VQ000 VQ000 ort size With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread Mixed sizes and with port plug Mixed size for different types of piping, option installed Q Cable (Length) 0 Without cable Cable length. m Cable length m Cable length m VQ000 VQ000 Note ) Insert L (Top ported) or (ottom ported) for elbow type. Example) (ottom ported elbow with ø One-touch fitting) Note ) Indicate LM for models with elbow fittings and mixed cylinder port sizes. Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size One-touch fittings are available. efer to Semi-standard on page 0 for details. Option Symbol Note ) D D0 D Note ) K Note ) N Note ) Option With back pressure check valve DIN rail mounting With DIN rail bracket (Without DIN rail) DIN rail length specified ( : 0 to ) Special wiring specifications (Except double wiring) With name plate External pilot [Option] Note ) When two or more symbols are specified, indicate them alphabetically. Example) -S Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) The number of stations that may be displayed is longer than the manifold number of stations. Note ) Specify the wiring specifications by means of the manifold specification sheet. Note ) Indicate for the valve with external pilot.

22 ase Mounted lug-in Unit Series -VQ000/000 Connector ssembly Electric circuit diagram (elow wiring is the case of all double solenoid connections.) Flat ribbon cable connector Terminal no. Connector terminal no. Triangle mark indicator position Station Station Station Station Station Station Station 7 Station SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL s the standard electrical wiring specifications, double wiring (connected to SOL. and SOL. ) is adopted for the internal wiring of each station for stations or less, regardless of valve and option types. Mixed single and double wiring is available as semi-standard. efer to page 9 for details. VDC +. How to Order Valves 0 0 VQ 0 0 Series VQ000 VQ000 Clean series Copper/Fluorine/Silicon free + Low particle generation 0 Type of actuation -position single -position double -position closed center -position exhaust center -position pressure center Seal Metal seal ubber seal Coil voltage VDC Function Symbol Specifications K Note ) Note ) Standard High-speed response type High- pressure type (.0 Ma) External pilot DC (0. W) (0.9 W) (0.9 W) Manual override C D Non-locking push type (Tool required) Locking type (Tool required) Locking type (Manual) Slide locking type (Manual) Light/surge voltage suppressor E Yes Q [Option] Note ) Metal seal only Note ) efer to Semi-standard on page 0 for external pilot specifications. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. How to Order Manifold ssembly Specify the part numbers for valves and options together beneath the manifold base part number. <Example> Flat ribbon cable with terminal block with cable ( m) VVQ-0CG VQ00- VQ00- VQ00- refix the asterisk to the part nos. of the solenoid valve, etc. VQ00- VQ00- VQ00- set Manifold base part no. sets Valve part no. ( to ) set Valve part no. (Station ) sets Valve part no. ( to ) VQ00- VQ00- VQ00- VQ00- Write sequentially from the st station on the D-side. When part nos. written collectively are complicated, specify them by means of the manifold specification sheet. m U side D side

23 G Series -VQ000/000 (Flat ribbon cable with terminal block) -VVQ The dashed lines and dimensions in parentheses indicate DIN rail mounting [-D]. (). Indicator light ower supply terminal block (Terminal screw M) 9 (L) (L) L L = 0. Indicator light 7 (.) Manual override 0 9. () (.).. (). Triangle mark indicator position x M mounting hole pplicable connector: Flat ribbon cable connector (0) (Complies with MIL-C-0) D side 7 n U side C [() EH port] C: ø One-touch fitting DIN rail clamp screw (7.) C, C, C, M [(), () port] C: ø. One-touch fitting C: ø One-touch fitting C: ø One-touch fitting M: M thread. = 0.. C [() SU port] C: ø One-touch fitting Dimensions L n L L (L) (L) With ejector unit: Formula L = 0.n (Number of ejector units x.7) L = 0.n +. + (Number of ejector units x.7) L is L plus about Formula L = 0.n +., L = 0.n + n: Station (Maximum stations) a

24 ase Mounted lug-in Unit Series -VQ000/000 -VVQ The dashed lines indicate DIN rail mounting [-D] (with DIN rail mounting bracket). ower supply terminal block (Terminal screw M) () 7. Indicator light. L Indicator light L. =. 0.9 Manual override + VDC + COM 0 () (.) pplicable connector: Flat ribbon cable connector (0) (Complies with MIL-C-0) (L) (L) x M mounting hole (.) D side 7 n U side Flat ribbon cable connector assembly (0) T00-FC0-:. m T00-FC0-: m T00-FC0-: m EH C0 [() EH port] C0: ø0 One-touch fitting EH DIN rail clamp screw C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting = C0 [() SU port] C0: ø0 One-touch fitting (7.) () Dimensions L n L L (L) (L) Formula L = n +, L = n + 7 n: Station (Maximum stations)

25 T Series -VQ000/000 (Terminal block box) Manifold Specifications - - Series VQ000 VQ000 Open the terminal block cover to connect the wires to the terminal block. Step. emoving the terminal block cover Loosen the screws on the terminal block cover and open it in the direction shown by the arrow. The cover can then be removed from the terminal block.. iping specifications iping ort size direction Side Side (), () C C0 (), () C, C, C, M C, C, C Series VQ000 VQ000 Manifold lug-in unit 0 stations Terminal lock Connection ( -VQ000) M. How to Order Manifold a Step. Mounting the terminal block cover Hook groove (a) on shaft (b) and close the cover. Then tighten the screws. Drip proof plug assembly (for G /): T Cover Step. Wiring The diagram on the left shows the terminal block wiring schematic. ll stations are provided with double solenoid wiring. Insert each lead wire into the terminal opening and tighten the screw directly above. How to connect is inserting the lead wire into the terminal window, then tighten the screw on the top. (Tightening torque: 0. to 0. N m) VVQ 0 C T 0 Clean series Copper/Fluorine/Silicon free + Low particle generation Note ) stations Note ) VQ000: Max. 0 stations efer to page 9 for details. For negative common specifications of series VQ000, refer to Semi-standard on page 9. For series VQ000 the standard manifold can be used. (a) (b) Cylinder port Symbol C Note ) C Note ) C Note ) C Note ) M CM Note ) Note ) MM Note ) pplicable stations Max. stations Max. 0 stations ort size With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread Mixed sizes and with port plug Mixed size for different types of piping, option installed VQ000 VQ000 Note ) Insert L (Top ported) or (ottom ported) for elbow type. Example) (ottom ported elbow with ø One-touch fitting) Note ) Indicate LM for models with elbow fittings and mixed cylinder port sizes. Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size One-touch fittings are available. efer to Semistandard on page 0 for details. G / Electrical entry D side D side VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VVQ000- I compliant - VVQ This has a small terminal block inside a junction box. The electrical entry port { - VQ000: G /, - VQ000: G /} permits connection of conduit fittings. Maximum stations: ( - VQ000), 0 ( - VQ000) Enclosure: Dust-tight, Water-jet-proof (I) compatible (Series VQ000) - VVQ Electrical Wiring Specifications: -VQ000 st row --nd row rd row The quantity of terminal blocks used depends on the number of manifold stations: Manifold to stations 9 to stations Terminal block rows rows s the standard electrical wiring specifications, double wiring (connected to SOL. and SOL. ) is adopted for the internal wiring of each station for stations or less, regardless of valve and option types. Mixed single and double wiring is available as semi-standard. efer to page 9 for details. Station Station Station Station Station Station Station 7 Station Station 9 Station 0 Station Station COM. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. COM. Terminal no. COM COM ositive COM spec. olarity Note) Negative COM spec. Option Symbol Option VQ000 VQ000 Note ) D D0 D Note ) K Note ) N Note ) W x G / Electrical entry Note) When using the negative common specifications, use valves for negative common. efer to Semi-standard on page 9 for details. Q Note) For models, DC-type only. Note) For models, DC-type only. With back pressure check valve DIN rail mounting With DIN rail bracket (Without DIN rail) DIN rail length specified ( : 0 to ) Special wiring spec. (Except double wiring) With name plate External pilot Enclosure: Dust-tight, Water-jet-proof (I) The total number of stations is tabulated starting from station one on the D-side. [Option] Note ) When two or more symbols are specified, indicate them alphabetically. Example) -S Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) The number of stations that may be displayed is longer than the manifold number of stations. Note ) Specify the wiring specifications by means of the manifold specification sheet. Note ) Indicate for the valve with external pilot.

26 ase Mounted lug-in Unit Series -VQ000/000 Terminal lock Wiring ( - VQ000) Step. Wiring Loosen screws on the terminal block, connect wiring and complete it by tightening screws.(tightening torque: 0. to 0.7 N m) The diagram on the right shows the terminal block wiring. ll stations are provided with double wiring regardless of the valves which are mounted. M ound head combination screw pplicable crimped terminal:.-s,.y-,.y-n,.y-. Name plate: VVQ000-N-T Drip proof plug assembly (for G /): T00-0 How to Order Valves 0 0 VQ 0 0 Series VQ000 VQ000 Clean series Copper/Fluorine/Silicon free + Low particle generation Open the terminal block cover to connect the wires to the terminal block. Step. emoving the terminal block cover Loosen mounting screws ( pcs.) on the terminal block cover and remove the cover. Type of actuation -position single -position double -position closed center -position exhaust center -position pressure center 0 Seal Metal seal ubber seal Caution Use the standard (DC) specification when continuously energizing for long periods of time. Function Symbol Specifications K Note ) N Note ) Note ) Cover Step. Mounting the terminal block cover Securely tighten the screws after confirming that the gasket is installed correctly. (Tightening torque: 0.7 to. N m) Standard High-speed response type High-pressure type (.0 Ma) Negative common External pilot Note) For models, DC-type only. Special Wiring Specifications: - VQ000 s the standard electrical wiring specifications, double wiring (connected to SOL. and SOL. ) is adopted for the internal wiring of each station for 0 stations or less, regardless of valve and option types. Mixed single and double wiring is available as semi-standard. efer to page 9 for details. Note) When using the negative common specifications, use valves for negative common. efer to Semi-standard on page 9 for details. Manual override Non-locking push type (Tool required) Locking type (Tool required) C Locking type (Manual) D Slide locking type (Manual) Light/surge voltage suppressor E DC (0. W) (0.9 W) (0.9 W) Yes C Enclosure Dust-protected W Note) Note ) Note) VQ000 only Coil voltage [Option] Q Note) For models, DC-type only. Dust-tight, Water-jet-proof (I) 00 VC (0/0 Hz) 0 VC (0/0 Hz) VDC VDC Station Station Station Station Station Station Station 7 Station Station 9 Station 0 D side U side VQ00- VQ00- SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. VQ00- VQ00- VQ00- VQ00- Terminal no. VVQ COM. ositive COM spec. olarity Note) Negative COM spec. How to Order Manifold ssembly Specify the part numbers for valves and options together beneath the manifold base part number. <Example> Terminal block box VVQ-0CT0 VQ00- VQ00- VQ00- VVQ000- refix the asterisk to the part nos. of the solenoid valve, etc. Note ) efer to page 9 for power consumption of C type. Note ) Metal seal only Note ) efer to Semi-standard on pages 9 to 0 for external pilot and negative common specifications. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. set Manifold base part no. sets Valve part no. ( to ) sets Valve part no. ( to ) set Valve part no. (Station 7) set lanking plate part no. (Station ) Write sequentially from the st station on the D-side. When part nos. written collectively are complicated, specify them by means of the manifold specification sheet. 7 F J G T L S M Sub-plate Single Unit Semistandard Construction Exploded View of Manifold Manifold Optional arts Safety Instructions Specific roduct recautions

27 T Series -VQ000/000 (Terminal block box) -VVQ < >: C The dashed lines and dimensions in parentheses indicate DIN rail mounting [-D]. (). <7.> Top entry port Not machined 9 (L) (L) L L = 0. Indicator light 7 (.) Manual override 9. <00.> 0 () (.). x M mounting hole 7 DIN rail clamp screw D side 7 n U side C [() EH port] C: ø One-touch fitting G / () (7.) C, C, C, M [(), () port] C: ø. One-touch fitting C: ø One-touch fitting C: ø One-touch fitting M: M thread = 0... C [() SU port] C: ø One-touch fitting Dimensions L n L L (L) (L) With ejector unit: Formula L = 0.n (Number of ejector units x.7) L = 0.n +. + (Number of ejector units x.7) L is L plus about Formula L = 0.n +., L = 0.n n: Station (Maximum stations) a

28 U SIDE ST D SIDE TEMINNL NO. U SIDE ST D SIDE TEMINNL NO. ase Mounted lug-in Unit Series -VQ000/000 -VVQ < >: C The dashed lines indicate DIN rail mounting [-D] (with DIN rail mounting bracket). () 00 (L) (L) L L Indicator light = 0.9. (.). Manual override 7. 0 <.9> x M mounting hole (.) 0. (). 0 D side 7 n U side DIN rail clamp screw (L) (L) L + 0. L x G / Electrical entry EH C0 [() EH port] C0: ø0 One-touch fitting EH <.9> 0 9. C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting = C0 [() SU port] C0: ø0 One-touch fitting (7.) (). Dust-tight, Water-jet-proof Dimensions L n L L (L) (L) Formula L = n +., L = n + n: Station (Maximum 0 stations)

29 L Series -VQ000/000 (Lead wire) I compliant Direct electrical entry. Models with one or more stations are available. (SU) and (EH) ports are provided on one side for further space savings. Maximum stations are. Enclosure: Dust-tight, Water-jet-proof (I) compatible ( -Series VQ000) Wiring Specifications: ositive COM Three lead wires are attached to each station regardless of the type of valve which is mounted. The red wire is for COM connection. SOL. Lead wire color lack SOL. Lead wire color lack - VVQ Manifold Specifications Series - VQ000 - VQ000 D side U side iping direction Side Side iping specifications (), () C C0 ort size (), () C, C, C, M C, C - VVQ pplicable stations Max. stations Max. stations COM. ed COM. ed SOL. SOL. Single solenoid Double solenoid lack: side solenoid ed: COM Station number Cable cores x WG : side solenoid (Not used for single solenoid) - VVQ D side U side Use any of the below cable lead wire assembly to change the lead wire length: Lead wire assembly with connector Lead wire length 0. m. m m Station number to How to Order Manifold a Manifold lug-in unit 0 0 Series VQ000 VQ000 art no. VVQ VVQ VVQ VVQ 0 C L Clean series Copper/Fluorine/Silicon free + Low particle generation station stations Note) For negative common specifications, refer to Semi-standard on page 9. Cylinder port Symbol C Note ) C Note ) C Note ) C Note ) M CM Note ) Note ) MM Note ) Cable (Length) 0 Cable length 0. m Cable length. m Cable length m ort size With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread Mixed sizes and with port plug Mixed size for different types of piping, option installed The total number of stations is tabulated on the D-side. VQ000 VQ000 Note ) Insert L (Top ported) or (ottom ported) for elbow type. Example) (ottom ported elbow with ø One-touch fitting) Note ) Indicate LM for models with elbow fittings and mixed cylinder port sizes. Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size One-touch fittings are available. efer to Semi-standard on page 0 for details. Q Note) For models, DC-type only. Option Symbol Note ) D D0 D Note ) N Note ) W Option - VVQ Note) For models, DC-type only. 00/0 VC models (F/L only) With back pressure check valve DIN rail mounting With DIN rail bracket (Without DIN rail) DIN rail length specified ( : 0 to 0) With name plate External pilot Enclosure: Dust-tight, Water-jet-proof (I) [Option] VQ000 VQ000 Note ) When two or more symbols are specified, indicate them alphabetically. Example) -S Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) The number of stations that may be displayed is longer than the manifold number of stations. Note ) Indicate for the valve with external pilot.

30 ase Mounted lug-in Unit Series -VQ000/000 Wiring Specifications: Negative COM (Semi-standard) Three lead wires are attached to each station regardless of the type of valve which is mounted. The black wire is for COM connection. SOL. Lead wire color ed SOL. Lead wire color ed COM. lack COM. lack - VVQ Dust-tight, Water-jet-proof SOL. Single solenoid SOL. Double solenoid ed: side solenoid lack: COM. Station number Cable cores x WG : side solenoid (Not used for single solenoid) How to Order Valves 0 VQ 0 0 Series VQ000 VQ000 Type of actuation 0 0 -position single -position double -position closed center -position exhaust center -position pressure center Seal Metal seal ubber seal Clean series Copper/Fluorine/Silicon free + Low particle generation Symbol Specifications K Note ) N Note ) Note ) Standard High-speed response type High-pressure type (.0 Ma) Negative common External pilot Function DC C (0. W) (0.9 W) (0.9 W) Note ) Note) For models, DC-type only. Note ) efer to page 9 for power consumption of C type. Note ) Metal seal only Note ) For external pilot and negative common specifications, refer to Semi-standard on pages 9 to 0. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. Manual override Non-locking push type (Tool required) Locking type (Tool required) C Locking type (Manual) D Slide locking type (Manual) Light/surge voltage suppressor E Yes Enclosure Dust-protected W Note) Note) VQ000 only Lead wire assembly with connector Lead wire length 0. m. m m Station number to art no. VVQ000-N-- VVQ000-N-- VVQ000-N-0- Note) When using the negative common specifications, use valves for negative common. For negative common specifications, refer to Semistandard on page 9. [Option] Q Note) For models, DC-type only. Dust-tight, Water-jet-proof (I) Coil voltage 00 VC (0/0 Hz) 00 VC (0/0 Hz) 0 VC (0/0 Hz) 0 VC (0/0 Hz) VDC VDC How to Order Manifold ssembly Specify the part numbers for valves and options together beneath the manifold base part number. <Example> Lead wire with cable ( m) VVQ-0CL VQ00- VQ00- VQ00- VVQ000- refix the asterisk to the part nos. of the solenoid valve, etc. D side U side set Manifold base part no. sets Valve part no. ( to ) sets Valve part no. ( to ) set Valve part no. (Station ) set lanking plate part no. (Station ) Write sequentially from the st station on the D-side. When part nos. written collectively are complicated, specify them by means of the manifold specification sheet. VQ00- VQ00- VQ00- VQ00- VVQ000- VQ00- Caution Use the standard (DC) specification when continuously energizing for long periods of time.

31 L Series -VQ000/000 (Lead wire) -VVQ < >: C The dashed lines indicate DIN rail mounting [-D] (with DIN rail mounting bracket). (). <7.> (L) (L) L L = 0. Indicator light. (.) Manual override. 9. <00.> Number of stations (.) () 0. Lead wire WG x cores. x M mounting hole D side 7 n U side C [() EH port] C: ø One-touch fitting DIN rail clamp screw C [() SU port] C: ø One-touch fitting 0. = 0. (7.) () C, C, C, M [(), () port] C: ø. One-touch fitting C: ø One-touch fitting C: ø One-touch fitting M: M thread Dimensions L n L L (L) (L) Formula L = 0.n +., L = 0.n + n: Station (Maximum stations) With ejector unit: Formula L = 0.n +. + (Number of ejector units x.7) L = 0.n + + (Number of ejector units x.7) L is L plus about a

32 ase Mounted lug-in Unit Series -VQ000/000 -VVQ < >: C The dashed lines indicate DIN rail mounting [-D] (with DIN rail mounting bracket). () Lead wire WG x cores. Number of 7. <77.> stations 0.9 (L) (L) (.) L L Manual override Indicator light.. x M mounting hole <.9> () (.) Dust-tight, Water-jet-proof D side n U side C0 [() EH port] C0: ø0 One-touch fitting EH DIN rail clamp screw () (7.) C0 [() SU port] C0: ø0 One-touch fitting = C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting Dimensions L n L L (L) (L) Formula L = n +, L = n + 7 n: Station (Maximum stations)

33 S Series -VQ000/000 (Serial transmission) ase mounted plug-in manifold: For E0 Gateway-type serial transmission system 0 Cylinder port Manifold series VQ000 VQ000 Valve stations Symbol 0 station 0 Note) Max. stations. (Special wiring specifications) How to Order Manifold stations Symbol ort size VQ000 VQ000 C C C C M CM Note ) L L L L L LM Note ) N N N7 N9 MT NM Note ) LN LN LN7 LN9 LT N N N7 N9 T With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread With mixed sizes and with port plug Top ported elbow with ø. One-touch fitting Top ported elbow with ø One-touch fitting Top ported elbow with ø One-touch fitting Top ported elbow with ø One-touch fitting Top ported elbow M thread ottom ported elbow with ø. One-touch fitting ottom ported elbow with ø One-touch fitting ottom ported elbow with ø One-touch fitting ottom ported elbow with ø One-touch fitting ottom ported elbow M thread Elbow port, mixed sizes ø/" with One-touch fitting ø/" with One-touch fitting ø/" with One-touch fitting ø/" with One-touch fitting UNF thread With mixed sizes and with port plug Top ported elbow with ø/" One-touch fitting Top ported elbow with ø/" One-touch fitting Top ported elbow with ø/" One-touch fitting Top ported elbow with ø/" One-touch fitting Top ported elbow UNF thread ottom ported elbow with ø/" One-touch fitting ottom ported elbow with ø/" One-touch fitting ottom ported elbow with ø/" One-touch fitting ottom ported elbow with ø/" One-touch fitting ottom ported elbow UNF thread LNM Note ) MM Note ) N SI unit part no. SI unit specifications Symbol SI unit specifications Metric size Inch size N 0 VVQ NN output (+COM.) N output ( COM.) NN output (+COM.) N output ( COM.) Elbow port, mixed sizes S 0 D SI unit part no. ES00 ES0 Mixed size for different types of piping, option installed Note ) Indicate Mixed sizes and with port plug in the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. efer to est neumatics No. q for details on E0 gatewaytype serial transmission system. Clean series Copper/Fluorine/Silicon free + Low particle generation Option Note ) D Note ) K Note ) N Note ) DIN rail mounting With back pressure check valve DIN rail length specified ( : 0 to ) Special wiring spec. (Except double wiring) With name plate with external pilot Note ) When two or more symbols are specified, indicate them alphabetically. Example) -S Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) Specify the wiring specifications by means of the manifold specification sheet. Note ) Indicate for the valve with external pilot. Note ) The number of stations that may be displayed is longer than the manifold number of stations. How to Order Manifold ssembly Example VVQ-S0C-D VQ00- VQ00- VQ00- Q D side U side [Option] set (S, -station manifold part no.) sets (Single type part no.) sets (Double type part no.) set ( position type part no.) The asterisk denotes the symbol for assembly. refix it to the part nos. of the solenoid valve, etc. Enter in order starting from the first station on the D-side. dd the valve and option part numbers under the manifold base part number. In the case of complex arrangement, specify them by means of the manifold specification sheet.

34 ase Mounted lug-in Manifold Series -VQ000/000 0 Clean series Copper/Fluorine/Silicon free + Low particle generation 0 How to Order Valves VQ 0 0 Series VQ000 VQ000 Type of actuation -position single Manual override : Non-locking push type (Tool required) Q [Option] Metal -position double : Locking type (Tool reguired) ubber -position double -position closed center C: Locking type (Manual) -position exhaust center -position pressure center D: Slide locking type (Manual) ated voltage VDC Function Symbol K Note ) N Note ) Note ) Specifications Standard (0. W) High-speed response type (0.9 W) High-pressure type (.0 Ma) [0.9 W] Negative common External pilot Note ) Metal seal only Note ) For external pilot and negative common specifications, refer to Semi-standard on pages 9 to 0. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. Seal 0 Metal seal ubber seal

35 7 9 0 S Series -VQ000/000 (Serial transmission) ase mounted plug-in manifold: For E0 Gateway-type serial transmission system -VVQ pplicable connector: Flat ribbon cable connector (0) (Complies with MIL-C-0) ().. L L L L (n-) x Indicator light 7 Manual override W COM. D side 7 n U side C [() EH port] C: ø One-touch fitting DIN rail clamp screw C, C, C, M [(), () port] C: ø. One-touch fitting C: ø One-touch fitting C: ø One-touch fitting M: M thread = 0... C [() SU port] C: ø One-touch fitting Dimensions L n L L L L Formula L = 0.n +., L = 0.n + 9 n: Station (Maximum stations)

36 7 0 9 ase Mounted lug-in Manifold Series -VQ000/000 -VVQ pplicable connector: Flat ribbon cable connector (0) (Complies with MIL-C-0) () 7... L L (.) L L. =. Indicator light 0.9 Manual override EH EH COM W D side 7 n U side DIN rail clamp screw C0 [() EH port] C0: ø0 One-touch fitting. 9 C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting = 7. C0 [() SU port] C0: ø0 One-touch fitting Dimensions L n L L L L Formula L = n +, L = n + 0 n: Station (Maximum stations)

37 S Series -VQ000/000 (Serial transmission): For E0// Integrated-type (Output) serial transmission system I compliant The serial transmission system reduces wiring work, while minimizing wiring and saving space. Enclosure: Dust-tight, Water-jet-proof (I) compatible (Series VQ000) Manifold Specifications Series - VQ000 - VQ000 iping direction Side Side iping specifications (), () C C0 ort size (), () C, C, C, M C, C, C pplicable stations Max. stations Max. stations How to Order Manifold 0 0 Cylinder port Symbol Symbol F H J J Q V Z ZN VVQ 0 C V 0 Note) Series VQ000 VQ000 Manifold lug-in unit rotocol NKE Corp.: Fieldbus System NKE Corp.: Fieldbus H System SUN Corp.: S-LINK ( outputs) SUN Corp.: S-LINK ( outputs) DeviceNet OMON Corp.: Compous/S ( outputs) OMON Corp.: Compous/S ( outputs) CC-LINK stations stations Note ) efer to page 9 for details. Note ) Max. stations. (Specify a model with 9 to stations by means of the manifold specification sheet.) C Note ) C Note ) C Note ) C Note ) M CM Note ) Note ) MM Note ) CompoNet (ositive common) CompoNet (Negative common) S SI unit specifications Symbol rotocol 0 Without SI unit F NKE Corp.: Fieldbus System H NKE Corp.: Fieldbus H System J SUN Corp.: S-LINK ( outputs) J SUN Corp.: S-LINK ( outputs) Q DeviceNet System OMON Corp.: Compous/S ( outputs) OMON Corp.: Compous/S ( outputs) V CC-LINK Z CompoNet (ositive common) ZN CompoNet (Negative common) VQ000 VQ000 SI Unit art No. (Without option W [Dust-protected (-) is included.]) SI unit part no. Standard: E0-SUW Dust-protected: E0-SUW- Standard: E0-SUH Dust-protected: E0-SUH- Standard: E0-SSL Dust-protected: E0-SSL- Standard: E0-SSL Dust-protected: E0-SSL- Standard: E0-SDN Dust-protected: No part no. Standard: E0-SCS Dust-protected: E0-SCS- Standard: E0-SCS Dust-protected: E0-SCS- Standard: E0-SMJ Dust-protected: E0-SMJ- Standard: E0-SCM Dust-protected: No part no. Standard: E0-SCM Dust-protected: No part no. Enclosure Note) Dust-protected Max. stations Max. stations Max. stations Max. stations Max. stations Note ) Insert L (Top ported) or (ottom ported) for elbow type. Example) (ottom ported elbow with ø One-touch fitting) Note ) Indicate as LM for models with elbow fittings and mixed cylinder port sizes. Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size One-touch fittings are available. efer to Semi-standard on page 0 for details. Note) efer to SI Unit art No. when ordering the CE-compliant SI unit. efer to est neumatics No. q for details on the E0// integrated-type (Output) serial transmission system. efer to SMC Information (0-E) for details on CompoNet. Clean series Copper/Fluorine/Silicon free + Low particle generation ort size With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread Mixed sizes and with port plug Mixed size for different types of piping, option installed Q Note) Suffix - for the dust-protected type SI units (Except SI unit specification Q ) Note) efer to SI Unit art No. when ordering the CE-compliant SI unit. Option Symbol Option VQ000 VQ000 Note ) With back pressure check valve D DIN rail mounting D Note ) Special K Note ) N Note ) W DIN rail mounting ( : 0 to ) wiring specifications (Except double wiring) With name plate With external pilot Enclosure: Dust-tight, Water-jet-proof (I) [Option] Note ) When two or more symbols are specified, indicate them alphabetically. Example) -S. Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) The number of stations that may be displayed is longer than the manifold number of stations. Note ) Specify the wiring specifications by means of the manifold specification sheet. Note ) Indicate for the valve with external pilot. SI Unit art No. (With option W) Symbol rotocol SI unit part no. F H J J Q V NKE Corp.: Fieldbus System NKE Corp.: Fieldbus H System SUN Corp.: S-LINK ( outputs) SUN Corp.: S-LINK ( outputs) DeviceNet System OMON Corp.: Compous/S ( outputs) OMON Corp.: Compous/S ( outputs) CC-LINK ED-SUW ED-SUH ED-SSL ED-SSL ED-SDN ED-SCS ED-SCS ED-SMJ

38 ase Mounted lug-in Unit Series -VQ000/000 G / G / prepared hole - VVQ - VVQ - VVQ Dust-protected (-) - VVQ Dust-tight, Water-jet-proof (-W) How to Order Valves 0 0 VQ 0 0 Series VQ000 VQ000 Clean series Copper/Fluorine/Silicon free + Low particle generation Type of actuation -position single -position double -position closed center -position exhaust center -position pressure center Q Enclosure Dust-protected Dust-tight, Water-jet-proof W Note) (I) Note) - VQ000 only [Option] Manual override Non-locking push type (Tool required) Locking type (Tool required) C Locking type (Manual) D Slide locking type (Manual) How to Order Manifold ssembly Specify the part numbers for valves and options together beneath the manifold base part number. <Example> VVQ-0CSV VQ00- VQ00- VQ00- VVQ000- refix the asterisk to the part nos. of the solenoid valve, etc. D side U side set Manifold base part no. sets Valve part no. ( to ) sets Valve part no. ( to ) set Valve part no. (Station 7) set lanking plate part no. (Station ) VVQ000- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- VQ00- Write sequentially from the st station on the D-side. When part nos. written collectively are complicated, specify them by means of the manifold specification sheet. 0 Seal Metal seal ubber seal Coil voltage VDC; With indicator light/ surge voltage suppressor Function Symbol Specifications Standard DC (0. W) K Note ) N Note ) Note High-speed response type Highpressure type (.0 Ma) Negative common External pilot (0.9 W) (0.9 W) Note ) Metal seal only Note ) For external pilot and negative common specifications, refer to Semi-standard on pages 9 to 0. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. 9

39 S Series -VQ000/000 (Serial transmission): For E0 Integrated-type (Output) serial transmission system -VVQ. L7 L L (L) (n-) x 0. The dashed lines indicate DIN rail mounting [-D] (with DIN rail mounting bracket). SMC V 9. Drawing shows a SC case. (general purpose type) 0V FG S E I L U N I T MODEL SC (SI No.E0-ST) UN T/ E D I S W. Dust-protected SI unit ()... (L) (L) L L (n-) x (.) Indicator light Manual override SMC V V FG S E I L U N I T MODEL SC (SI No.E0-ST) UN T/ E D I S W. Drawing shows a SC case. (.) () x M mounting hole D side 7 n U side C [() EH port] C: ø One-touch fitting DIN rail clamp screw (7.) () 9. C, C, C, M [(), () port] C: ø. One-touch fitting C: ø One-touch fitting C: ø One-touch fitting M: M thread = 0.. C [() SU port] C: ø One-touch fitting Dimensions L n L L (L) (L) Dust-protected SI unit: L = 0.n + 97, L = L +, L7 = L + Formula L = 0.n +., L = 0.n + 7. n: Station (Maximum stations)

40 S E I L U N I T MODEL S (SI No.E-SM) x x 0 E. D SD UN OWE STTION NO. ase Mounted lug-in Unit Series -VQ000/000 -VVQ L7 = L + L = L + L = n + 0 L. (n-) x The dashed lines indicate DIN rail mounting [-D] (with DIN rail mounting bracket). L = L + 0 L0 = L + 0 L9 = n + SMC V () 7. 0V FG S E I L U N I T MODEL SC (SI No.E0-ST) UN T/ E Drawing shows a SC case. DI SW. Dust-protected SI unit E : x G/ E : x G/ Electrical entry Use a drip proof plug ass y (T00-0) on the unused conduit port (G/). 00 L = n +. Dust-tight, Water-jet-proof (I) SI unit (E/ Integrated-type (output) serial transmission system) (L) (L) (.) L L. (n-) x.. = 0.9 Indicator light Manual override V 0V FG S E I L U N I T MODEL SC (SI No.E0-ST) SMC UN T/ E DI SW. Drawing shows a SC case. (.) () x M mounting hole D side 7 n U side EH EH C0 [() EH port] C0: ø0 One-touch fitting DIN rail clamp screw Dimensions L n L L (L) (L) () (7.) C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting = C0 [() SU port] C0: ø0 One-touch fitting Dust-protected SI unit: L = n + 0, L = L +, L7 = L + Dust-tight, Water-jet-proof SI unit: L = n +., L9 = n + L0 = L + 0, L = L + 0 Formula L = n +, L = n + n: Station (Maximum stations)

41 S Series -VQ000 (Serial transmission): For E0 Integrated-type (I/O) serial transmission system I compliant VQ000 only The serial transmission system reduces wiring work, while minimizing wiring and saving space. How to Order Manifold 0 0 Symbol C Note ) C Note ) C Note ) CM Note ) Note ) MM Note ) VQ000 lug-in series 0 station Cylinder port ort size With ø one-touch fitting With ø one-touch fitting With ø one-touch fitting Mixed sizes and with port plug Mixed size for different types of piping, option installed stations SI unit mounting D: D side mounting efer to est neumatics No. q for details on the E0 integrated-type (I/O) serial transmission system. How to Order Manifold Seal Metal seal ubber seal Model 0W QW NWN VQ 0 0 W Type of actuation -position single -position double -position closed center -position exhaust center -position pressure center VVQ 0 C D QW N W Clean series Copper/Fluorine/Silicon free + Low particle generation Note ) Insert L (Top ported) or (ottom ported) for elbow type. Example) (ottom ported elbow with ø one-touch fitting) Note ) Indicate LM for models with elbow fittings and mixed cylinder port sizes. Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size one-touch fittings are available. efer to Semi-standard on page 0 for details. Clean series Copper/Fluorine/Silicon free + Low particle generation Note) For external pilot and negative common specifications, refer to Semi-standard on pages 9 to 0. S Function Symbol Specifications K Note ) N Note ) Note ) Standard High-speed response type High-pressure type (.0 Ma) Negative common External pilot 0 N Without SI unit DeviceNet OFIUS-D Option Symbol K N Input block type +COM. COM. Enclosure I (Dust-tight, Water-jet-proof) N sensor input (+COM) or without SI unit/input block NN sensor input ( COM) Number of input blocks Without SI unit Without input block With pc. input block With pcs. input blocks With pcs. input blocks With pcs. input blocks Enclosure I (Dust-tight, Water-jet-proof) Manual override Non-locking push type (Tool required) Locking type (Tool required) C Locking type (Manual) D Slide locking type (Manual) DC (0. W) (0.9 W) (0.9 W) Coil voltage Q Option With back pressure check valve Special wiring spec. (Except double wiring) With name plate External pilot Note) When two or more symbols are specified, indicate them alphabetically. Example: -N Note) Only +COM is available for DeviceNet. Order a mounting valve with +COM. Since OFIUS is COM only, order COM for valves to be mounted. VDC; With indicator light/surge voltage suppressor Note ) Metal seal only Note ) For external pilot and negative common specifications, refer to Semi-standard on pages 9 to 0. Note ) When a valve is compatible with OFIUS D, the SI unit is negative common. Select valves for negative common. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. Q efer to SI Unit art No. when ordering the CE-compliant SI unit. Caution Use the standard (DC) specification when continuously energizing for long periods of time.

42 ase Mounted lug-in Unit Series -VQ000 -VVQ (Serial transmission : E0).. () Min. 0 to Max. unit (0 to mm) L (In case of pc. input block: number of inputs) Indicator light L Manual override = x M mounting hole If the input block is attached, it comes with a bracket Input block D side 7 n 0. U side C0 [() EH port] C0: ø0 One-touch fitting EH C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting = 9.. C0 [() SU port] C0: ø0 One-touch fitting Dimensions L n L L Formula L = n +. L = n + (In case of pc. DI unit, mm will be added for increasing every pc.) n: Station (Maximum stations)

43 M Series -VQ000 (Circular connector) - VVQ VQ000 only MIL flat cable connector reduces installation labor for electrical connection. Manifold and connectors, both compliant with the I rating (Dust-tight, Water-jet-proof), provide a high-degree of protection for the electrical parts. Maximum stations are. Circular Connector ( ins) Manifold Specifications Series - VQ000 iping direction Side iping specifications (), () C0 ort size (), () C, C, M pplicable stations Max. stations T00-MC Circular connector cable assembly included in a specific manifold model no. efer to How to Order Manifold. L Multi-core vinyl cable 0. mm x cores ø0 lug terminal no. Socket side Circular connector cable assembly Cable length (L). m m m ssembly part no. T00-MC-0 T00-MC-00 T00-MC-00 Cannot be used for transfer wiring. Note) Lengths other than the above are also available. lease contact SMC for details. Note Cable -core x WG Electrical characteristics Item roperty Conductor resistance Ω/km, 0 C Voltage limit V, min, C Insulation resistance MΩ/km, 0 C or less 000 or more Note) The minimum bending radius of the circular connector cable is 0 mm. Circular connector cable assembly terminal no. Terminal no. Lead wire color Dot marking Cable ssembly lack rown ed Orange Yellow ink lue urple Gray Yellow Orange Yellow ink lue urple Gray Orange ed rown ink Gray lack lack lack ed ed ed lack lack lack ed ed How to Order Manifold stations stations VVQ 0 C N Clean series Copper/Fluorine/Silicon free + Low particle generation Series VQ000 Manifold lug-in unit Note) efer to page 9 for details. M Cylinder port Symbol ort size C Note ) With ø One-touch fitting C Note ) With ø One-touch fitting C Note ) With ø One-touch fitting CM Note ) Note ) Mixed sizes and with port plug MM Note ) Mixed size for different types of piping, option installed W Enclosure I (Dust-tight, Water-jet-proof) Cable (Length) 0 Without cable With cable (. m) With cable ( m) With cable ( m) Note ) Insert L (Top ported) or (ottom ported) for elbow type. Example) (ottom ported elbow with ø one-touch fitting) Note ) Indicate LM for models with elbow fittings and mixed cylinder port sizes. Note ) Indicate Mixed sizes and with port plug by means of the manifold specification sheet. Note ) When selecting the mixed size for different types of piping, dual flow fitting assembly, or double check block (direct mounting), enter MM and give instructions in the manifold specification sheet. Note ) Inch-size one-touch fittings are available. efer to Semistandard on page 0 for details. Option Symbol Note ) D D0 D Note ) K Note ) N Note ) Note) For models, DC-type only. [Option] Q Note) For models, DC-type only. Option With back pressure check valve DIN rail mounting With DIN rail bracket (Without DIN rail) DIN rail mounting ( : 0 to ) Special wiring spec. (Except double wiring) With name plate External pilot Note ) When two or more symbols are specified, indicate them alphabetically. Example) -K Note ) Models with a suffix - have check valves for prevention of back pressure at all manifold stations. When a back pressure check valve is desired, and is to be installed only in certain manifold stations, specify the mounting position by means of the manifold specification sheet. Note ) The number of stations that may be displayed is longer than the manifold number of stations. Note ) Specify the wiring specifications by means of the manifold specification sheet. Note ) Indicate for the valve with external pilot.

44 ase Mounted lug-in Unit Series -VQ000 U side D side - VVQ The total number of stations is tabulated starting from station one on the D-side. Electrical Wiring Specifications s the standard electrical wiring specifications, double wiring (connected to SOL. and SOL. ) is adopted for the internal wiring of each station for stations or less, regardless of valve and option types. Mixed single and double wiring is available as semi-standard. efer to page 9 for details. Station Station Station Station Station Station Station 7 Station Station 9 Station 0 Station Station (Max.) SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. SOL. COM. COM. Note) When using the negative common specifications, use valves for negative common. (efer to page 9.) efer to Semi-standard on page 9 for details. Terminal no ositive COM spec. Circular connector cable assembly 0 T00-MC-00 Wire color 00 olarity Lead wire color Dot marking Note) Negative COM spec. lack rown ed Orange Yellow ink lue urple Gray Yellow Orange Yellow ink lue urple Gray Orange ed rown ink Gray lack lack lack ed ed ed lack lack lack ed ed How to Order Valves 0 Type of actuation -position single -position double -position closed center -position exhaust center -position pressure center 0 0 Seal Metal seal ubber seal VQ 0 0 Series VQ000 Clean series Copper/Fluorine/Silicon free + Low particle generation Caution Use the standard (DC) specification when continuously energizing for long periods of time. Function Symbol Specifications K Note ) N Note ) Note ) Standard High-speed response type High-pressure type (.0 Ma) Negative common External pilot DC (0. W) (0.9 W) (0.9 W) Note ) For power consumption of C type, refer to page 9. Note ) Metal seal only Note ) For external pilot and negative common specifications, refer to Semi-standard on pages 9 to 0. Note ) When two or more symbols are specified, indicate them alphabetically. Combination of [] and [K] is not possible. Note) For models, DC-type only. C Note ) C D Non-locking push type (Tool required) Locking type (Tool required) Locking type (Manual) Slide locking type (Manual) Light/surge voltage suppressor E W Q Note) For models, DC-type only. Enclosure I (Dust-tight, Water-jet-proof) Manual override Yes [Option] Coil voltage 00 VC (0/0 Hz) 0 VC (0/0 Hz) VDC VDC How to Order Manifold ssembly Specify the part numbers for valves and options together beneath the manifold base part number. <Example> Circular connector with cable ( m) VVQ-09CM-W VQ00- VQ00- VQ00- VVQ000- refix the asterisk to the part nos. of the solenoid valve, etc. m set Manifold base part no. sets Valve part no. ( to ) sets Valve part no. ( to ) sets Valve part no. ( 7 to ) set lanking plate part no. (Station 9) Write sequentially from the st station on the D-side. When part nos. written collectively are complicated, specify them by means of the manifold specification sheet. D side U side

45 M Series -VQ000 (Circular connector) -VVQ < >: C The dashed lines and dimensions in parentheses indicate DIN rail mounting [-D]. (L) Made by CONINVES GmbH HC-NWF <77.> (L) (.) L L Indicator light Manual override.. x M mounting hole () <.9> (.) () D side 7 n U side C0 [() EH port] C0: ø0 One-touch fitting C0 [() SU port] C0: ø0 One-touch fitting EH EH DIN rail clamp screw () C, C, C [(), () port] C: ø One-touch fitting C: ø One-touch fitting C: ø One-touch fitting = (7.) Dimensions L n L L (L) (L) Formula L = n + 77., L = n n: Station (Maximum stations)

46 Sub-plate Single Unit VQ000 Only Series -VQ000 Note) For models, DC-type only. [Option] How to Order I enclosure in standard specifications Easy-to-use terminal block 0 0 In the case of Valve + Sub-plate VQ 0 0 W 0 W Note ) Entry is the same as standard products. Clean series Copper/Fluorine/Silicon free + Low particle generation Dust-protected Enclosure I (Dust-tight, Water-jet-proof) Note ) Valves are I specifications. Note ) When the valve is a standard (dustprotected) specification, it is not compatible with 00 or 0 VC. ort size 0 Thread type N T F / Q Note) For models, DC-type only. c NT NTF G Terminal block In the case of Sub-plate alone Dimensions VQ000 W 0 x ø. (Mounting hole) Manual override Indicator light 0. ( port) 9. (.) 0. ( port) VQ0 0-7 <7.9> Clamp screw 7.7 <7.7> 70.7 M x 0. External pilot port. 0 (, port) G / Electrical entry x /" (), (), (), (), () port < >: C Note) When using this valve for I, mount a seal connector to the electrical entry. 7

47 Series -VQ000/000 Semi-standard Different Number of Connector ins F and s with the following number of pins are available besides the standard number (F = ; = ). Select the desired number of pins and cable length from the cable assembly list. lace an order for the cable assembly separately. F (D-sub connector) pins (Flat ribbon cable) 0//0 pins How to Order Manifold How to Order Manifold -VVQ 0 C F S -VVQ 0 C SC Option Option Cylinder port Cylinder port Kit type/electrical entry How to Order D-sub connector, pins Connector location Side Without cable Location ins Top entry Side entry Location ins (Max. 7 stations) F U F S 0 (Max. stations) In the same way as the -pin models (standard), the terminal no. is for SOL. at the st station, the terminal no. 9 for SOL. at the st station, and the terminal no. for COM. D-sub Connector Cable ssembly Cable length (L). m m m ins T00-DS- T00-DS- T00-DS- For other commercial connectors, use a type conforming to MIL-C-0. Multi-core vinyl cable VVF 0. mm x cores ø9 lug connector HD-CTH (Made by Hirose Electric) Connector HD-S (Made by Hirose Electric) x M. 0. Terminal no. Wire Color Table by Terminal No. of D-sub Connector Cable ssembly Terminal no Lead wire color lack rown ed Orange Yellow ink lue urple Gray Yellow Orange Yellow ink Dot marking lack lack ed ed ed lack lack Kit type/electrical entry (Max. 7 stations) 0 (Max. 9 stations) Cable length (L). m m m ins Top entry 0 0 T00-FC T00-FC T00-FC 7. U U UC Flat ibbon Cable ssembly Connector width (W) How to Order Flat ribbon cable, 0 pins Connector location Side Without cable T00-FC- T00-FC- T00-FC-. Side entry S S SC In the same way as the -pin models (standard), the terminal no. is for SOL. at the st station, the terminal no. for SOL. at the st station, and two pins from the max. terminal numbers are for COM. Terminal no. T00-FC0- T00-FC0- T00-FC0- For other commercial connectors, use a type with strain relief conforming to MIL-C-0. 0 ed

48 ase Mounted lug-in Unit Series -VQ000/000 Special Wiring Specifications In the internal wiring of F//J/G/T/S, double wiring (connected to SOL. and SOL. ) is adopted for each station regardless of the valve and option types. Mixed single and double wiring is available as an option.. How to Order Indicate an option symbol -K, for the manifold no. and be sure to specify the mounting position and number of stations of the single and double wiring by means of the manifold specification sheet. -VVQ 0CFU D K S Negative Common Specifications Specify the valve model no. as shown below for negative common specification. The manifold no. shown below is for the T (VQ000) and L (VQ000/000) s. For other s the standard manifold can be used. However, negative common is not compatible with S (except E0 gateway-type, E0 integrated-type and E0/ / integrated-type (CompoNet )) and G s. How to Order Valves N Negative common specifications Others, option symbols: to be indicated alphabetically.. Wiring specifications With the side solenoid of the st station as no. (meaning, to be connected to no. terminal), without making any terminals vacant. How to Order Manifold T (VQ000): C T N rd row nd row st row COM. Cylinder port Option Negative common specifications F D-sub connector () Kit F (D-sub connector) U F Type S Max. points Kit Type U F S -VQ00 Max. points -VQ000 (Flat ribbon cable) U S U 0 T (Terminal block box) U U S C S S 0 S (Serial transmission) S G (Flat ribbon cable with terminal block) G -VQ000 Flat ribbon cable connector () rows of terminal blocks J/G 0 T T Terminal block Terminal block (VQ000, terminals) (VQ000) rows of terminal blocks J (Flat ribbon cable) M (Circular connector) M M. Max. number of stations The maximum number of stations depends upon the number of solenoids. ssuming one for a single and two for a double, determine the number of stations so that the total number is not more than the max. number given in the following table. J U S 0 L (VQ000/000): -VVQ 0 -VVQ Cylinder port C L N Negative common specifications Electrical entry Cable length 0 With cable (0. m) With cable (. m) With cable ( m) Option 9

49 Series -VQ000/000 Semi-standard External ilot Specifications When the supply air pressure is lower than the required minimum operating pressure (0. to 0. Ma) for the solenoid valve (or when the valve is used for vacuum), specify an external pilot model. Order a manifold or valve by suffixing the external pilot specification,. The -port of the manifold base is equipped with one-touch fittings for external pilot. VQ000: C (ø one-touch fitting) VQ000: C (ø one-touch fitting) How to Order Manifold -VVQ 0CFU S -VQ00 External pilot specifications Others, option symbols: to be indicated alphabetically. How to Order Valves External pilot specifications Note ) When two or more functions are specified, indicate them alphabetically. Note ) Since the pilot EH of this valve is released from the passage, it is not possible to vacuum from a part other than EH pressure and SU ports. Inch-size One-touch Fittings The valve with inch-size one-touch fittings is shown below. -VVQ 0 N7 S0 Cylinder port Symbol pplicable tubing O.D. (Inch) (), () port VQ000 VQ000 N N ø/" ø/" ø/" ø/" Option Kit type/electrical entry N7 N9 MT NM UNF (M thread) Mixed Note) When inch-size fittings are selected for the cylinder port, inch-size fittings are selected on (), () port, too. DIN ail Mounting Each manifold can be mounted on a DIN rail. Order it by indicating a DIN rail mounting option symbol, -D. In this case, a DIN rail which is approx. 0 mm longer than the manifold with the specified number of stations is attached. When DIN rail is unnecessary (DIN rail mounting brackets only are attached.) Indicate the option symbol, -D0, for the manifold part number. How to Order Manifold -VVQ 0CFU D 0 S How to Order Manifold Others, option symbols: to be indicated alphabetically. When using DIN rail longer than the manifold with specified number of stations Clearly indicate the necessary number of stations next to the option symbol -D for the manifold part number. -VVQ 0CFU D 09 S Others, option symbols: to be indicated alphabetically. The number of stations that may be displayed is longer than the manifold number of stations. No. VVQ000-7 (For VQ000) VVQ000-7 (For VQ000) pcs. per one set. DIN rail for 9 stations When changing to a DIN rail mounting. Order brackets for mounting a DIN rail. (efer to Manifold Optional arts on pages 9 and.) When ordering DIN rail only DIN rail no.: T00-D- s for, specify the number from the DIN rail table. efer to the dimensions of each for L dimension. (itch) 0 (), () port size VQ000 ø/" (N9) VQ000 ø/" (N) L Dimension L =. x n + 0. No L dimension No. L dimension No. L dimension No. L dimension

50 Series -VQ000/000 Construction -VQ000 lug-in Unit: Main arts/eplacement arts Metal seal e q w ubber seal e q w r -VQ00 () () ()()() r -VQ0 () () ()()() e q w e q w -VQ00 () () -VQ0 () () r ()()() e q w r ()()() e q w -VQ00 -VQ00 () () () () -VQ0 -VQ0 () () () () r -VQ00 ()()() () () ()()() r -VQ0 ()()() () () ()()() ()()() ()()() Component arts No. Description ody Spool/Sleeve iston ilot valve assembly Material Zinc die-casted Stainless steel esin Note Note) efer to page for How to Order ilot Valve ssembly. Component arts No. Description ody Spool valve iston ilot valve assembly Material Zinc die-casted luminum, HN esin Note Note) efer to page for How to Order ilot Valve ssembly.

51 Series -VQ000/000 -VQ000 lug-in Unit: Main arts/eplacement arts Metal seal ubber seal e q w e q w r -VQ00 () () r -VQ0 () () ()()() ()()() e q w e q w -VQ00 () () -VQ0 () () r ()()() e q w r ()()() e q w -VQ00 -VQ00 () () () () -VQ0 -VQ0 () () () () r -VQ00 ()()() () () ()()() r -VQ0 ()()() () () ()()() ()()() ()()() Component arts No. Description ody Spool/Sleeve iston ilot valve assembly Material Zinc die-casted Stainless steel esin Note Note) efer to page for How to Order ilot Valve ssembly. No. Description ody Spool valve iston ilot valve assembly Material Zinc die-casted luminum, HN esin Note Note) efer to page for How to Order ilot Valve ssembly.

52 Exploded View of Manifold -VQ000 lug-in Unit: Exploded View (F//J/L/S ) Housing assembly, SI unit, D-side end plate assembly r Manifold block assembly U-side end plate assembly S q r y /J! i w r!0 o! pins (Top entry) (Integral housing type)!! F pins (Upward side entry) r! pins (Side entry) e u L t

53 Exploded View of Manifold <Housing ssembly and SI Unit> Housing assembly and SI unit no. No. Manifold art no. Description (SF ) (SH ) (SJ ) E0-SUW(-) Note ) E0-SUH(-) Note ) E0-SSL(-) Note ) q (SJ ) E0-SSL(-) Note ) (SQ ) E0-SDN (S ) (S ) (SV ) (SZ ) (SZN ) E0-SCS(-) Note ) E0-SCS(-) Note ) E0-SMJ(-) Note ) E0-SCM E0-SCM w e U S U J S FU FS T00-- U T00--J S 0 T00--FU T00--FS <D-Side End late ssembly> rt D-side end plate assembly no. VVQ <Manifold lock ssembly> i Manifold block assembly no. VVQ Electrical entry F0 Without lead wire F F for to stations/double wiring F F for to stations/double wiring F F for to stations/single wiring /J/S for to stations/double wiring /J/S for to stations/double wiring /J/S for to stations/single wiring L0 L0 : ( to ) L L : ( to ) L L : ( to ) Note ) Note ) Note ) Top entry connector for U, JU while side entry connector for S, JS. Note ) Suffix - to the end of the part number for dust-protected SI unit. (Not available for S/SQ ) Electrical entry FU For F top entry pins F For F other than above For J For J L For L S For S <eplacement arts for Manifold lock> eplacement arts <Fitting ssembly>! Fitting assembly part no. (For cylinder port) VVQ ort size No. art no. Description Material Quantity o!0!! VVQ VVQ VVQ VVQ Gasket acking Clamp screw Clip HN HN Carbon steel Stainless steel Note) set of parts containing pcs. each is enclosed. U S Option Note ) S Note ) Common EH External pilot Direct EH outlet with built-in silencer Note ) When both options are specified, indicate as S. Note ) The housing assembly and SI unit of F//J/S are not included (except FU). Separately place an order for q, w, e. Tie-rod ( pcs.) and lead wire assembly for extensions are attached. ort size C C C M C0 With ø. One-touch fitting With ø One-touch fitting With ø One-touch fitting M thread Without One-touch fitting (With clip) NKE Corp.: Fieldbus System ( outputs) NKE Corp.: Fieldbus H System ( outputs) SUN Corp.: S-LINK System ( outputs) SUN Corp.: S-LINK System ( outputs) DeviceNet OMON Corp.: Compous/S ( outputs) OMON Corp.: Compous/S ( outputs) CC-LINK CompoNet (ositve common) CompoNet (Negative common) Flat ribbon cable housing assembly = Number of pins: /0//0 Flat ribbon cable housing assembly D-sub connector housing assembly (Top entry) Number of pins: D-sub connector housing assembly (Side entry) = Number of pins: / Note) The! s fitting assembly is included. u U-side end plate assembly no. (For L ) VVQ000---L <U-Side End late ssembly> y U-side end plate assembly no. (For F//J/S ) VVQ Option Note) urchasing order is available in units of 0 pieces.! Fitting assembly part no. (For (), () port) VVQ000--C Note) urchasing order is available in units of 0 pieces. C C C M pplicable tubing ø! Tie-rod assembly part no. ( pcs./set) ilot valve assembly V - Function Symbol Specifications DC Standard (0. W) K S Common EH External pilot Direct EH outlet with built-in silencer pplicable tubing ø. pplicable tubing ø pplicable tubing ø M thread Note ) lease order when eliminating manifold stations. When adding stations, tie-rods are attached to the manifold block assembly. Therefore, it is not necessary to order. Note ) : 0 to Note ) For S//J/F/L VVQ000-T- - High-speed response type High-pressure type (.0 Ma) (0.9 W) (0.9 W) C Note ) Coil voltage 00 VC (0/0 Hz) 00 VC (0/0 Hz) 0 VC (0/0 Hz) 0 VC (0/0 Hz) VDC VDC Note ) efer to page 9 for power consumption of C type. Note ) Common to single solenoid and double solenoid Enclosure Dust-tight, Water-jet-proof (I) Dust-protected

54 Exploded View of Manifold -VQ000 lug-in Unit: Exploded View (F//J/L/G/S ) Housing assembly and SI unit D-side end plate assembly Manifold block assembly U-side end plate assembly q!0! o /J u w!!! F t!! e G S r i L y

55 Exploded View of Manifold <Housing ssembly and SI Unit> Housing assembly and SI unit no. No. Manifold art no. Description (SF ) E0-SUW(-) Note ) [ED-SUW] Note ) (SH ) E0-SUH(-) Note ) [ED-SUH] Note ) (SJ ) E0-SSL(-) Note ) [ED-SSL] Note ) q (SJ ) E0-SSL(-) Note ) [ED-SSL] Note ) (SQ ) E0-SDN [ED-SDN] Note ) (S ) E0-SCS(-) Note ) [ED-SCS] Note ) (S ) E0-SCS(-) Note ) [ED-SCS] Note ) (SV ) E0-SMJ(-) Note ) [ED-SMJ] Note ) (SZ ) E0-SCM (SZN ) E0-SCM w e r Note ) Suffix - to the end of the part number for dust-protected SI unit. Note ) Dust-tight, Water-jet-proof (I) Note ) Top entry connector for FU, U, JU while side entry connector for FS, S, JS. <D-Side End late ssembly> ty D-side end plate assembly no. VVQ Electrical entry Enclosure F J L G S U S U J S U F S G For F For For J For L For G For S T00-- U T00--J S 0 U T00--F S T00--GU0 Option Note ) S Note ) Note ) When both options are specified, indicate as S. Note ) The housing assembly and SI unit of F//J/G/S are not included. Separately place an order for q, w, e, r. Note ) S (uilt-in silencer) and W (I) cannot be combined. <eplacement arts for Manifold lock> eplacement arts No. art no. Description Material Quantity!0!!! VVQ VVQ VVQ VVQ Gasket Seal Clamp screw Clip HN HN Carbon steel Stainless steel W <Manifold lock ssembly> o Manifold block assembly no. VVQ Electrical entry F0 Without lead wire F F for to stations/double wiring F F for to stations/double wiring F F for to stations/single wiring /J/G/S for to stations/double wiring /J/G/S for to stations/double wiring /J/G/S for to stations/single wiring L0 L0 : ( to ) L L : ( to ) L L : ( to ) T T for to 0 stations/double wiring T T for to 0 stations/single wiring M M for to stations/double wiring M M for to stations/double wiring M M for to stations/single wiring Note) set of parts containing pcs. each is enclosed. U S Note ) Note ) Note ) Dust-protected Dust-tight, Water-jet-proof (I) Note) F//J/G are available with only. M is available with [W] only. S/L/T are selectable depending on the manifold type. Common EH External pilot Direct EH outlet with built-in silencer Tie-rod ( pcs.) and lead wire assembly for extensions are attached. ort size C C C C0 NKE Corp.: Fieldbus System ( outputs) NKE Corp.: Fieldbus H System ( outputs) SUN Corp.: S-LINK System ( outputs) SUN Corp.: S-LINK System ( outputs) DeviceNet OMON Corp.: Compous/S ( outputs) OMON Corp.: Compous/S ( outputs) CC-LINK CompoNet (ositve common) CompoNet (Negative common) Flat ribbon cable housing assembly : Number of pins: /0//0 Flat ribbon cable housing assembly D-sub connector housing assembly : Number of pins: / Flat ribbon cable housing assembly with terminal block VVQ000-T- <U-Side End late ssembly> u U-side end plate assembly no. (For F//J/G/T/S/M ) VVQ Option Enclosure With ø One-touch fitting With ø One-touch fitting With ø One-touch fitting Without One-touch fitting (With clip) S Common EH External pilot Direct EH outlet with built-in silencer Note ) The! s fitting assembly is included. Note ) The housing assembly and SI unit of F//J/G/S are not included. Separately place an order for q, w, e, r. Note ) S (uilt-in silencer) and W (I) cannot be combined. Note) urchasing order is available in units of 0 pieces. Note) urchasing order is available in units of 0 pieces. ort size C C C pplicable tubing ø pplicable tubing ø pplicable tubing ø! Fitting assembly part no. (For (), () port) VVQ000--C0 pplicable tubing ø0! Tie-rod assembly part no. ( pcs./set) <Fitting ssembly>! Fitting assembly part no. (For cylinder port) VVQ000-- W W Dust-protected Dust-tight, Water-jet-proof (I) i U-side end plate assembly no. (For L ) VVQ000---L- Enclosure Enclosure W Note) F//J/G are available with only. M is available with [W] only. S/T are selectable depending on the manifold type. Dust-protected Dust-tight, Water-jet-proof (I) Note) Select it depending on the manifold type. Dust-protected Dust-tight, Water-jet-proof (I) Note) F//J/G are available with only. M is available with [W] only. S/L/T are selectable depending on the manifold type. Note ) lease order when eliminating manifold stations. When adding stations, tie-rods are attached to the manifold block assembly. Therefore, it is not necessary to order. Note ) : 0 to Note ) For S//J/F/L 7

56 Series -VQ000 -VQ000: Manifold Optional arts lanking plate assembly VVQ000- JIS symbol It is used by attaching on the manifold block for being prepared for removing a valve for maintenance reasons or planning to mount a spare valve, etc. Individual SU spacer C VVQ N7 When the same manifold is to be used for different pressures, individual SU spacers are used as SU ports for different pressures. (One station space is occupied.) lock both sides of the station, for which the supply pressure from the individual SU spacer is used, with SU block plates. (efer to the application example.) Specify the spacer mounting position and SU block plate position by means of the manifold specification sheet. The block plate is used in one or two places for one set. (Two SU block plates for blocking SU station are attached to the individual SU spacer.) s a standard, electric wiring is connected to the position of the manifold station where the individual SU spacer is mounted. If wiring is not required for stations equipped with spacers, enter in the special wiring specifications column in the manifold specification sheet. SU block plate D side Individual SU spacer C (SU port) C: ø one-touch fitting lock indication label label indicating the SU passage blocking position is to be adhered. U side D side SU block plate SU block plate Valve Individual Valve Valve SU spacer U side Individual EH spacer VVQ C N7 When valve exhaust affects other stations due to the circuit configuration, this spacer is used for individual valve exhaust. (One station space is occupied.) lock both sides of the individual valve EH station. (efer to the application example.) Specify the mounting position, as well as the EH block base or EH block plate position by means of the manifold specification sheet. The block plate is used in one or two places for one set. n EH block base assembly is used in the blocking position when ordering an EH spacer incorporated with a manifold no. However, do not order an EH block base assembly because it is attached to the spacer. When separately ordering an individual EH spacer, separately order an EH block base assembly because it is not attached to the spacer. s a standard, electric wiring is connected to the position of the manifold station where the individual EH spacer is mounted. If wiring is not required for stations equipped with spacers, enter in the special wiring specifications column in the manifold specification sheet. SU block plate VVQ000- When different pressures are supplied to a manifold, a SU block plate is used to block the stations under different pressures. Specify the mounting position by means of the manifold specification sheet. <lock indication label> Indication labels to confirm the blocking position are attached (Each for SU passage and SU/EH passage blocking positions). When ordering a block plate incorporated with a manifold, a block indication label is attached to the manifold. EH passage blocked EH block base assembly Individual EH spacer D side C (EH port) C: ø one-touch fitting lock indication label label indicating the EH passage blocking position is to be adhered. lock indication label U side SU passage blocked Description/Model Valve Option D side Single Individual EH spacer VVQ000---C EH blocking position: Specify places. Individual EH spacer + EH block base assembly (Not to be Valve ordered) SU/EH passage blocked 7 Valve + EH block base assembly Valve (Not to be ordered) U side

57 7 ase Mounted lug-in Unit Series -VQ000 EH block base assembly F VVQ (C/C/C/M/N/N/N7) L lack screw D side EH block base assembly U side Manifold block assembly Electrical entry F0 F F F L0 L L Without lead wire For F ( to stations)/double wiring For F ( to stations)/double wiring For F ( to stations)/single wiring For, G, T, S ( to stations)/double wiring For, G, T, S ( to stations)/double wiring For, G, T, S ( to stations)/single wiring L0 L to stations L The manifold block assembly is used between stations for which exhaust is desired to be divided when valve exhaust affects other stations due to the circuit configuration. The EH passage on the D-side is blocked in the EH block base assembly. It is also used in combination with an individual EH spacer for individual exhaust. <lock indication label> Indication labels to confirm the blocking position are attached. (Each for EH passage and SU/EH passage blocking positions) When ordering a EH block base incorporated with a manifold, a block indication label is attached to the manifold. EH passage blocked Solid forming D side U side Specify the mounting station by means of the manifold specification sheet. When ordering this option incorporated with a manifold, specify the EH block base assembly part number with in front of it beneath the manifold part number. EH passage blocked lock indication label SU/EH passage blocked ack pressure check valve assembly [-] VVQ000- It prevents cylinder malfunction caused by other valve exhaust entry. Insert it into (EH) port on the manifold side of a valve which is affected. It is effective when a single-acting cylinder is used or an exhaust center type solenoid valve is used. When ordering it being mounted on all manifold stations, suffix - to the end of the manifold part number. Note) When a back pressure check valve is desired, and is to be installed only in certain manifold stations, clearly indicate the part number and specify the mounting station by means of the manifold specification sheet. pcs. in set (recautions). The back pressure check valve assembly is the parts with a check valve structure. However, since the valve has slight air leakage, take precautions for the exhaust air not to be restricted at the exhaust port.. When a back pressure check valve is mounted, the effective area of the valve will decrease by about 0%. Name plate [-N] VVQ000- N -N-Station ( to Max. stations) NC It is a transparent resin plate for placing a label that indicates solenoid valve function, etc. Insert it into the groove on the side of the end plate and bend it as shown in the figure. When the blanking plate with connector is mounted, it automatically will be VVQ000-NC-n When ordering this option incorporated with a manifold, suffix -N to the end of the manifold part number. N: Standard NC: For mounting blanking plate with connector 9 = 0. Note) ( ): VVQ000-NC-n n: lanking plug (For one-touch fittings) KQ- It is inserted into an unused cylinder port and SU/EH ports. urchasing order is available in units of 0 pieces. ort plug VVQ0000- The plug is used to block the cylinder port. When ordering this option incorporated with a manifold, indicate CM for the port size of the manifold part number, as well as, the mounting station and cylinder port mounting positions () and () by means of the manifold specification sheet. Gently screw an M screw in the port plug hole and pull it for removal. DIN rail mounting bracket [-D,-D0,-D ] VVQ000-7 This bracket is used for mounting the manifold on the DIN rail. When ordering this option incorporated with a manifold, suffix -D to the end of the manifold part number. Dimensions pplicable fitting size ød. Model KQ- KQ-0 KQ-0 KQ-0 Hole L D pplicable fitting size ød /" /" /" /" Model KQ-0 KQ-0 KQ-07 KQ-09 L D set of DIN rail mounting brackets for manifold includes brackets. DIN rail clamp thread Mounting screws included 9

58 Series -VQ000 -VQ000: Manifold Optional arts lanking plate assembly VVQ000- JIS symbol It is used by attaching on the manifold block for being prepared for removing a valve for maintenance reasons or planning to mount a spare valve, etc. Individual SU spacer C VVQ N9 When the same manifold is to be used for different pressures, individual SU spacers are used as SU ports for different pressures. (One station space is occupied.) lock both sides of the station, for which the supply pressure from the individual SU spacer is used, with SU block plates. (efer to the application example.) Specify the spacer mounting position and SU block plate position by means of the manifold specification sheet. The block plate is used in one or two places for one set. (Two SU block plates for blocking SU station are attached to the individual SU spacer.) s a standard, electric wiring is connected to the position of the manifold station where the individual SU spacer is mounted. If wiring is not required for stations equipped with spacers, enter in the special wiring specifications column in the manifold specification sheet. SU block plate Individual SU spacer D side U side C (SU port) C: ø One-touch fitting lock indication label label indicating the SU passage blocking position is to be adhered. D side SU block plate SU block plate Valve Individual Valve Valve SU spacer U side Individual EH spacer C VVQ N9 When valve exhaust affects other stations due to the circuit configuration, this spacer is used for individual valve exhaust. (One station space is occupied.) lock both sides of the individual valve EH station. (efer to the application example.) Specify the mounting position, as well as the EH block base or EH block plate position by means of the manifold specification sheet. The block plate is used in one or two places for one set. (Two EH block plates for blocking EH station are attached to the individual EH spacer.) s a standard, electric wiring is connected to the position of the manifold station where the individual EH spacer is mounted. If wiring is not required for stations equipped with spacers, enter in the special wiring specifications column in the manifold specification sheet. Individual EH spacer EH block plate D side C (EH port) C: ø One-touch fitting U side lock indication label label indicating the EH passage blocking position is to be adhered. D side EH block plate EH block plate Valve Individual Valve Valve EH spacer U side SU block plate VVQ000- lock indication label When different pressures are supplied to a manifold, a SU block plate is used to block the stations under different pressures. Specify the mounting position by means of the manifold specification sheet. <lock indication label> Indication labels to confirm the blocking position are attached. (Each for SU passage and SU/EH passage blocking positions) SU passage blocked D side U side SU/EH passage blocked When ordering a block plate incorporated with a manifold, a block indication label is attached to the manifold. EH block plate VVQ000-9 The EH block plate is used between stations for which exhaust is desired to be divided when valve exhaust affects other stations configuration. It is also used in combination with an individual EH spacer for individual exhaust. Specify the mounting position by means of the manifold specification sheet. pcs. in set D side U side lock indication label <lock indication label> Indication labels to confirm the blocking position are attached. (Each for EH passage and SU/EH passage blocking positions) 0 EH passage blocked SU/EH passage blocked When ordering a block plate incorporated with a manifold, a block indication label is attached to the manifold.

59 ase Mounted lug-in Unit Series -VQ000 ack pressure check valve assembly [-] VVQ000- It prevents cylinder malfunction caused by other valve exhaust entry. Insert it into (EH) port on the manifold side of a valve which is affected. It is effective when a single-acting cylinder is used or an exhaust center type solenoid valve is used. When ordering assemblies incorporated with a manifold, add suffix - to the end of the manifold part number. Note) When a check valve for back pressure prevention is desired and is to be installed only in certain manifold stations, clearly indicate the part number and specify the mounting position by means of the manifold specification sheet. pcs. in set (recautions). The back pressure check valve assembly is assembly parts with a check valve structure. However, since the valve has slight air leakage, take precautions for the exhaust air not to be restricted at the exhaust port.. When a back pressure check valve is mounted, the effective area of the valve will decrease by about 0%. Name plate [-N] VVQ000-N-Station ( to Max. stations) It is a transparent resin plate for placing a label that indicates solenoid valve function, etc. Insert it into the groove on the side of the end plate and bend it as shown in the figure. When ordering this option incorporated with a manifold, suffix -N to the end of the manifold part number. = n: lanking plug (For One-touch fittings) KQ- It is inserted into an unused cylinder port and SU/EH ports. urchasing order is available in units of 0 pieces. DIN rail mounting bracket [-D,-D0,-D ] VVQ000-7 This bracket is used for mounting the manifold on the DIN rail. When ordering this option incorporated with a manifold, suffix -D to the end of the manifold part number. Dimensions pplicable fitting size ød 0 Model KQ-0 KQ-0 KQ-0 KQ-0 L D pplicable fitting size ød /" /" /" /" Model KQ-0 KQ-07 KQ-09 KQ- L D set of DIN rail mounting brackets for manifold includes brackets. DIN rail clamp thread

60 Series -VQ000/000 Specific roduct recautions e sure to read before handling. efer to back cover for Safety Instructions, Handling recautions for SMC roducts (M-E0-) for // ort Solenoid Valve recautions. Light/Surge Voltage Suppressor Caution The lighting positions are concentrated on one side for both single solenoid type and double solenoid type. In the double solenoid type, side and side energization are indicated by two colors which match the colors of the manual overrides. Manual override: Green Manual override: Orange (Drawing shows a VQ000 case.) Indicator light: Orange Indicator light : Orange : Green Single solenoid Double solenoid ush type (Tool required) ore ø. -VQ000 Manual Override Warning Without an electric signal for the solenoid valve the manual override is used for switching the main valve. ush type is standard. (Tool required) Locking type is semi-standard. (Tool required/manual) -VQ000 ore ø. Locking type (Tool required) <Semi-standard> ush down on the manual override with a small screwdriver, etc. until it stops. elease the screwdriver and the manual override will return. DC circuit diagram Single solenoid Stop diode Double solenoid Stop diode Surge absorption diode ore ø. -VQ000 ore ø. -VQ000 ush down on the manual override with a flat head screwdriver until it stops. Turn it clockwise by 90 to lock it. Turn it counterclockwise to release it. Light Surge absorption diode Note) -side energization: light (Orange) illuminates. -side energization: light (Green) illuminates. Light With wrong wiring prevention (stop diode) mechanism With a surge absorption (surge absorption diode) mechanism Locking type (Manual) <Semi-standard> 0 mm mm ush down on the manual override with a small flat head screwdriver or with your fingers until it stops. Turn it clockwise by 90 to lock it. Turn it counterclockwise to release it. -VQ000 -VQ000 Caution Do not apply excessive torque when turning the locking type manual override. (0. N m or less)

61 Series -VQ000/000 Specific roduct recautions e sure to read before handling. efer to back cover for Safety Instructions, Handling recautions for SMC roducts (M-E0-) for // ort Solenoid Valve recautions. Warning Manual Override Slide locking type (Manual) <Semi-standard> ore ø.7 OFF ON Orange OFF position Green ON position How to Mount/emove Solenoid Valves Caution Mounting. ress down on the clamp screw. Clamp bracket opens. Diagonally insert the hook on the valve end plate side into clamp.. ress the valve body downward. (When the screw is released, it will be locked by clamp bracket.). Tighten the clamp screw. (roper tightening torque: VQ000, 0. to 0. N m; VQ000, 0. to 0.7 N m.) Caution Dust on the sealing surface of the gasket or solenoid valve can cause air leakage. ore ø OFF ON VQ000 ore ø OFF ON Green ON position eplacement of Cylinder ort Fittings Caution The cylinder port fittings are a cassette for easy replacement. The fittings are blocked by a clip. Take out the clip with a flat head screwdrier, etc., then replace the fittings. For mounting, insert the fitting assembly until it strikes against the inside wall and then insert the clip to the specified position. Clip VQ000 Orange OFF position The manual override is locked by sliding it all the way to the pilot valve side (ON side) with a small flat head screwdriver or finger. Slide it to the fitting side (OFF side) to release it. In addition, it can also be used as a push type by using a screwdriver, etc., of ø.7 or less. (ø or less for VQ000). How to Mount/emove Solenoid Valves Caution pplicable tubing O.D. pplicable tubing ø. pplicable tubing ø pplicable tubing ø pplicable tubing ø M pplicable tubing ø/" pplicable tubing ø/" pplicable tubing ø/" pplicable tubing ø/" Fitting assembly Clip -VQ000 -VQ000 VVQ000-0-C VVQ000-0-C VVQ000-0-C Fitting assembly part no. -VQ000 VVQ000-0-M VVQ000-0-N VVQ000-0-N VVQ000-0-N7 -VQ000 Fittings assembly VVQ000--C VVQ000--C VVQ000--C VVQ000--N VVQ000--N7 VVQ000--N9 efer to Manifold Optional arts on pages 9 for other types of fittings. Clamp bracket Clamp bracket Clamp screw emoving. Loosen the clamp screw until it turns freely. (The screw is captive.). Lift the coil side of the valve body while pressing down slightly on the screw head and remove it from the clamp bracket. When the screw head cannot be pressed easily, gently press the area near the manual override of the valve. Caution. Use caution that O-rings must be free from scratches and dust. Otherwise, air leakage may result.. fter screwing in the fittings, mount the M fitting assembly on the manifold base. (Tightening torque: 0. to. N m). urchasing order is available in units of 0 pieces.