Base Mounted Series VQZ100/200/300. Nil. W Note) Compliant. Electrical entry. (DC speci- fication) terminal terminal. Coil voltage 24VDC

Transcription

1 Base Mounted Series VQZ00/00/00 VQZ00/00 / How to Order Valve Made to Order (For details, refer to page 9 and 4.) VQZ 5 5 M Series VQZ00 body width 5 mm VQZ00 body width 8 mm Type of actuation 4 N.C. N.O. N.C. N.O. (A) (R) (P) (A) (R) (P) (A) (R) (P) (A) (R) (P) Metal seal Rubber seal IP65 compliant Nil W Note) Compliant Note) VQZ00/00 DIN terminal rubber seal only (except external pilot). For details on IP65 enclosure, refer to page. Manual override Nil:Non-locking push type (Tool required) Port size [(A) port] Symbol Nil B:Locking type (Tool required) CE compliant Nil Q Port size Without sub-plate Rc /8 Rc /4 Rc /8 CE marked Note) AC-type models that are CE compliant have DIN terminals only. VQZ00 Note) For optional thread type, refer to page. VQZ Body type 5 Body mounted Note ) Option Note ) For details on external pilot type, refer to page. Note ) For AC specification power consumption, refer to page 9. Use standard (DC) specification for continuous duty. Function Symbol Specifications DC Nil B Note ) K Note ) Standard High speed response type High pressure type (Metal seal type only) External pilot type R Note, ) (0.5 W) Note ) AC High speed response/external BR Note, ) pilot type KR Note, ) High pressure/external pilot type (Metal seal type only) Electrical entry G:Grommet L: L-type plug LO: L-type plug M:M-type plug MO:M-type plug (DC speci- connector connector connector connector fication) with lead without with lead without wire connector wire connector + - Y: DIN terminal With light/ surge voltage +- With light/ surge voltage YO: DIN YZ: DIN terminal terminal without connector 4VDC With light/ surge voltage With light/ surge voltage - + With light/ surge voltage YOS: DIN Note ) YS: DIN Note ) terminal terminal without (DC speci- connector fication) (DC speci- fication) With surge voltage 4VDC With surge voltage Note ) Standard lead wire length: 00 mm Note ) For AC voltage valves there is no S option. It is already built-in to the rectifier circuit. Coil voltage 00 VAC (50/60 Hz) 00 VAC (50/60 Hz) 0 VAC [5 VAC] (50/60 Hz) 4 0 VAC [0 VAC] (50/60 Hz) 5 4 VDC 6 VDC Note) For sub-plate part no., refer to page. 8

2 Series VQZ00/00/00 Specifications Valve construction Fluid Max. operating pressure (MPa) 0.7 (High pressure type:.0) Min. operating pressure (MPa) Ambient and fluid temperature ( C) Max. operating frequency (Hz) Pilot exhaust method Lubrication Manual override Mounting orientation Impact/Vibration resistance (m/s ) Note ) Enclosure Metal seal 0 Individual exhaust Rubber seal Air, Inert gas 0 to 50 (No freezing) 5 Not required Push type, Locking type (Tool required) Free 50/0 Dustproof (DIN terminal: IP65 Note ) ) VQZ00 (Poppet seal) 0.7 (High pressure type:.0) 0 Common exhaust Based on IEC6059 Note ) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de- energized states every once for each condition. (Value in the initial state) Vibration resistance: No malfunction occurred in one sweep test between 45 and 000 Hz. Test was performed to axis and right angle directions of the main valve and armature when pilot signal is ON and OFF. (Value in the initial state) Note ) When IP65 compliant DIN terminals are selected: VQZ 5-YW-- Solenoid Specifications Options High speed response type High pressure type (Metal seal type only) External pilot type For details on external pilot type, refer to page. Symbol X0 X90 X Made to Order (For details, refer to page 4.) Description Pilot valve common exhaust Main valve fluoro-rubber All fluoro-rubber Electrical entry Coil rated voltage (V) Allowable voltage fluctuation Power consumption (W) Apparent power (VA) DC AC DC AC 50/60 Hz Standard High speed response, high pressure 00 V 0 V [5 V] 00 V 0 V [0 V] Grommet (G) L-type plug connector (L) M-type plug connector (M) DIN terminal (Y) G, L, M Y 4, 00, 0, 00, 0 ±0% of rated voltage 0.5 [(With light: 0.4 (DIN terminal with light: 0.45)] 0.9 [(With light: 0.95 (DIN terminal with light:.0)] 0.78 (With light: 0.8) 0.78 (With light: 0.87) 0.86 (With light: 0.89) [0.94 (With light: 0.97)] 0.86 (With light: 0.87) [0.94 (With light:.07)].8 (With light:.).5 (With light:.0).0 (With light:.4) [.4 (With light:.46)].7 (With light:.46) [.9 (With light:.60)] Surge voltage Varistor Indicator light LED (Neon light when AC with DIN terminal) In common between 0 VAC and 5 VAC, and between 0 VAC and 0 VAC. For 5 VAC and 0 VAC, the allowable voltage is 5% to +5% of rated voltage. Flow Characteristics Series VQZ00 VQZ00 VQZ00 9 Valve construc- tion N.C. valve N.C. valve N.O. valve N.C. valve N.O. valve Model Poppet Metal seal Rubber seal Metal seal Rubber seal Metal seal Rubber seal Metal seal Rubber seal VQZ5 VQZ5 VQZ5 VQZ5 VQZ45 VQZ5 VQZ5 VQZ5 VQZ45 (P A) Flow characteristics (A R) C [dm /(sbar)] b Cv C [dm /(sbar)] b Cv Note )Based on JIS B (Supply pressure: 0.5 MPa; with light/surge voltage : clean air) Response time values will change depending on pressure and air quality. Note )Weight without sub-plate. Standard: 0.5 W Response time (ms) Note ) High speed response: 0.9 W High pressure: 0.9 W AC or less or less or less 0.45 or less 4 or less 8 or less 4 or less 0.80 or less 5 or less 6 or less 0.9 or less 4 or less 8 or less 4 or less 0.74 or less 5 or less 6 or less 0.80 or less 7 or less or less 4 or less.0 or less 5 or less 57 or less 0.69 or less 7 or less or less 4 or less. or less 5 or less 57 or less Note ) Weight (g)

3 Base Mounted Series VQZ00/00/00 Dimensions: VQZ00 Single Unit Grommet (G): VQZ5-G- 0 0 /8, /4 [(A) port] x ø4.5 (For mounting) Manual override 4 A 4 Approx X 49.8 PE port 9 4 R P M5 x 0.8 (External pilot port) <External pilot only> /8, /4 [(P), (R) port] 8 (7) 0 (0.5) ( ): VQZ5-G-0 L-type plug connector (L): VQZ5-L- 0 0 DIN terminal (Y): VQZ5-Y- 0 0 Approx [8.] 49.8[56.8] Max Applicable cable O.D. ø.5 to ø7 Pg Unless otherwise indicated, dimensions are the same as Grommet (G). [ ]: AC M-type plug connector (M): VQZ5-M- 6. [68.] Approx [7.4] Unless otherwise indicated, dimensions are the same as Grommet (G). [ ]: AC Unless otherwise indicated, dimensions are the same as Grommet (G). [ ]: AC

4 Series VQZ00/00/00 Dimensions: VQZ00 Single Unit Grommet (G): VQZ5-G- 0 0 /4, /8 [(A) port] x ø4.5 (For mounting) 7 5 Manual override A 5 45 R P Approx X 57 PE port M5 x 0.8 (External pilot port) <External pilot only> /4, /8 [(P), (R) port] (9) 47 (4) ( ): VQZ5-G-0 L-type plug connector (L): VQZ5-L- 0 0 DIN terminal (Y): VQZ5-Y- 0 0 Approx [88.] 57 [64] Max. 0 Applicable cable O.D. ø.5 to ø7 Pg Unless otherwise indicated, dimensions are the same as Grommet (G). [ ]: AC M-type plug connector (M): VQZ5-M [75.] Approx [78.5] Unless otherwise indicated, dimensions are the same as Grommet (G). [ ]: AC Unless otherwise indicated, dimensions are the same as Grommet (G).

5 Series VQZ00/00/00 VQZ00/00 / How to Order Manifold Made to Order (For details, refer to page 4.) Series VQZ00 VQZ00 Symbol C4 C6 C8 C0 0 0 Note ) CM VVQZ 5 Manifold type 5 Base mounted Port size ø4 one-touch fitting ø6 one-touch fitting ø8 one-touch fitting ø0 one-touch fitting Rc /8 Rc /4 Mixed port sizes 0 0 Stations stations 0 stations 08 C6 Port size [(A) port] VQZ00 VQZ00 Note ) Specify port mixture/with port plug by means of the manifold specification sheet. Port mixture and port plug are available only for one-touch fitting type. Note ) For inch size one-touch fittings, refer to page. C Kit type C Option Nil None D DIN rail mounting (With standard DIN rail length) D0 Note) DIN rail mounting (Without DIN rail) R External pilot type Connector CE compliant Nil Q CE marked Note ) Order DIN rail separately. For DIN rail part no., refer to page. Note ) When two or more symbols are specified, indicate them alphabetically. VQZ00/00 / How to Order Valve VQZ 5 5 M Series VQZ00 body width 5 mm VQZ00 body width 8 mm 4 Type of actuation N.C. Metal seal N.O. Metal seal N.C. Rubber seal N.O. Rubber seal Body type 5 Base mouned Symbol Specifications DC AC (0.5 W) Nil Standard B Note ) High speed response type K Note ) High pressure type (Metal seal type only) R Note, ) External pilot type Note, ) BR High speed response/external pilot type KR Note, ) High pressure/external pilot type (Metal seal type only) Note ) Option Note ) For details on external pilot type, refer to page. Note ) For AC specification power consumption, refer to page 9. 5 Use standard (DC) specification for continuous duty. Function Note ) Manual override Nil Non-locking push type (Tool required) B Locking type (Tool required) Electrical entry Symbol G L LO M MO Y YO YZ YS Note ) YOS Note ) CE compliant Nil Q Electrical entry CE marked Note) AC-type models that are CE compliant have DIN terminals only. Grommet (DC specification) L-type plug connector with lead wire L-type plug connector without connector M-type plug connector with lead wire M-type plug connector without connector DIN terminal DIN terminal without connector DIN terminal DIN terminal (DC specification) DIN terminal without connector (DC specification) IP65 compliant Nil W Note) Compliant Note) VQZ00/00 DIN terminal rubber seal only (except external pilot). For details on IP65 enclosure, refer to page. Light/surge voltage None Note ) Standard lead wire length: 00 mm Note ) For AC voltage valves there is no S option. It is already built-in to the rectifier circuit. Coil voltage 00 VAC (50/60 Hz) 00 VAC (50/60 Hz) 0 VAC [5 VAC] (50/60 Hz) 4 0 VAC [0 VAC] (50/60 Hz) 5 4 VDC 6 VDC Yes None Yes Yes (Without light)

6 Base Mounted Series VQZ00/00/00 Manifold Specifications Series VQZ00 Base model VVQZ5- Piping specifications Piping Port size direction (P), (R) (A) Side/Top Rc /8 C (for ø.) C4 (for ø4) C6 (for ø6) M5 (M5 thread) Applicable Applicable solenoid stations valve VQZ5 to 0 stations Note) Manifold base weight (g) stations: 8 Addition per station: 9 VQZ00 VVQZ5- Side Rc /4 C4 (for ø4) C6 (for ø6) C8 (for ø8) Rc /8 VQZ5 to 0 stations stations: 6 Addition per station: 8 VQZ00 VVQZ5- Side (P) port C6 (for ø6) Rc /8 C8 (for ø8) (R) port C0 (for ø0) Rc /4 Rc /4 VQZ5 to 0 stations stations: 09 Addition per station: 60 Note) Weight for threaded connection. How to Order Manifold Assembly (Example) Stations U side VQZ5-5L 4 sets D side VVQZ5-05C6C VVQZ00-0A-5 VQZ5-5L set (C kit 5-station manifold base part no.) set (Blanking plate assembly part no.) 4 sets (N.C. type part no.) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. Enter in order starting from the first station on the D side. Add the valve and option part number under the manifold base part number. When entry of part numbers becomes complicated, indicate by the manifold specification sheet. C6: One-touch fitting for ø6 VVQZ00-0A-5 6

7 PE port M5 x 0.8 (X: External pilot port) <External pilot only> 7. (8) [(P), (R) port] 5.5 A /8 [(A) port] 5.5 Approx [64.8] Applicable cable O.D. ø.5 to ø7 Max Pg7 8 [84.] Series VQZ00/00/00 Dimensions: VQZ00 VVQZ5- Grommet (G) Stations Approx. 00 Port size C D side U side L L (5) (Rail mounting hole pitch:.5) (Pitch) P = 6 Manual override (DIN rail clamp thread) (DIN rail) 50 (.5).5 x ø4.5 (For mounting) 5 L4 R P L5 L R P (5.5) (5) (4.9) (66) (Station ) (Station n) 0.5 A A One-touch fitting [(A) port] Applicable tubing O.D.: ø4, ø5/" ø6, ø/4" ø8, ø5/6" () (7.5) 5.5 (Pitch) P = 6 /8 0.5 L-type plug connector (L) (Pitch) P = 6 M-type plug connector (M) DIN terminal (Y) The dashed lines indicate the DIN rail mounting [-D]. Approx [74.4] Dimensions L L L L L4 L5 9 Unless otherwise indicated, dimensions are the same as Grommet (G). [ ]: AC n Unless otherwise indicated, dimensions are the same as Grommet (G). [ ]: AC Unless otherwise indicated, dimensions are the same as Grommet (G). Formula: L5 = 6n + 0 L = 6n + 0 n: Stations (Max. 0 stations)

8 (5.5) (5) /4 [(A) port] A Approx [7.5] Approx [8.8] Applicable cable O.D. ø.5 to ø Pg [9.8] 79.8 [8] Base Mounted Series VQZ00/00/00 Dimensions: VQZ00 VVQZ5- Grommet (G) Stations Approx. 00 Port size C D side U side L L (5) (Rail mounting hole pitch:.5) (Pitch) P = 0 (DIN rail clamp thread) Manual override (DIN rail) PE port M5 x 0.8 (X: External pilot port) <External pilot only> /4 [(R) port] () x ø4.5 (For mounting) L4 R P 9 L5 L P R (8) /8 [(P) port] (5.5) 5.5 (66) (Station ) (Station n) 4.5 A A One-touch fitting [(A) port] Applicable tubing O.D.: ø6, ø/4" ø8, ø5/6" ø0, ø/8" () (7.5) 9.5 (Pitch) P = 0 /4 4.5 L-type plug connector (L) 9.5 (Pitch) P = 0 M-type plug connector (M) Max. 0 DIN terminal (Y) The dashed lines indicate the DIN rail mounting [-D]. Dimensions L L L L L4 L5 Unless otherwise indicated, dimensions are the same as Grommet (G). [ ]: AC n Unless otherwise indicated, dimensions are the same as Grommet (G). [ ]: AC Unless otherwise indicated, dimensions are the same as Grommet (G). Formula: L5 = 0n + 8 L = 0n + 6 n: Stations (Max. 0 stations)

9 Series VQZ00/00/00 Manifold Options Blanking plate assembly VVQZ00-0A-5 (for VQZ00) VVQZ00-0A-5 (for VQZ00) VVQZ00-0A-5 (for VQZ00) It is used by attaching on the manifold block for being prepared for removing a valve for maintenance reasons or planning to mount a spare valve, etc. Blanking plug KQP- KQP-04 KQP-06 KQP-08 KQP-0 L A ød Dimensions Applicable fitting size ød Model KQP- KQP-04 KQP-06 KQP-08 KQP (mm) A L D DIN rail AXT00-DR- L 7.5 As for, enter the number from the DIN rail dimensions table. For L dimension, refer to the dimensions of each kit. (5) (5) Each manifold can be mounted on a DIN rail. Insert D at the end of the manifold part number. The DIN rail is approximately 0 mm longer than the length of manifold. L Dimension L =.5n No. L dimension No L dimension Silencer (for manifold EXH port) Silencer is installed in the manifold EXH port. 6 8 ø AN0-0 AN00-0 ø Dimensions Model Silencer part no. VQZ00 AN0-0 VQZ00 AN00-0 VQZ00 AN00-0 Port plug VVQZ00-CP (for VQZ00) This is used when changing piping location. (Side or Top)

10 Series VQZ Options Base Mounted External Pilot Specification The external pilot specification is used when the operating pressure is below the minimum operating pressure 0. to 0.5 MPa or when valve is used for a vacuum application. Order a valve by adding the external pilot specification [R] to the part number. Valve Part No. VQZ 5R External pilot port Entry is the same as standard products. Manifold Part No. VVQZ 5 C Inch Size One-touch Fittings and Optional Threads Inch size one-touch fittings and NPT, NPTF and G thread are available. Manifold Part No. Entry is the same as standard products. VVQZ 5 N7 TC R Pressure Specifications Note ) External pilot pressure range Series Metal seal Rubber seal (VQZ00: poppet) VQZ00 Note ) VQZ00/00 Operating pressure range Note ) 00 kpa to 0.7 MPa Note ) In case of the high pressure type, upper limit of max. operating pressure and external pilot pressure range is MPa. Note ) When using the VQZ00 series for a vacuum application, vacuum air through its (P) port. When supplying vacuum-release air, supply it through its (R) port. But do not supply vacuum-release air exceeding 50% for the external pilot pressure. 0. to 0.7 MPa 0. to 0.7 MPa 0.5 to 0.7 MPa Entry is the same as standard products. Cylinder port Symbol N N N7 N9 N Applicable tubing O.D. ø/8" ø5/" ø/4" ø5/6" ø/8" Mixed Cylinder port VQZ00 VQZ00 VQZ00 NM Note ) M5 0 0 M5 thread /8 thread /4 thread Thread type (Cylinder port and (P), (R) ports) Nil N T F Rc NPT NPTF G Optional Threads Other than Rc Rc specifications are standard for all ports, however, NPT, NPTF and G are available for overseas markets. Add the appropriate symbol following the port size in the standard part number. Valve Part No. VQZ 5 T Entry is the same as standard products. IP65 Enclosure (Based on IEC59) DIN terminal is available with IP65 enclosure. Valve Part No. (Applicable to the VQZ00/00 rubber seal with the exception of the external pilot type) VQZ 5 Y W Note ) Except VQZ00, mixing one-touch fittings and thread types is impossible. Note ) Metric size one-touch fittings (C) are also available. Thread type (Cylinder port and (P), (R) ports of sub-plate) Nil N T F Rc NPT NPTF G Entry is the same as standard products. Note) The pilot exhaust IP65 valves is common with main valve exhaust. (The standard valve has an individual exhaust for the pilot valve.)

11 Series VQZ Base Mounted Replacement Parts One-touch Fitting Assembly (for Cylinder port) Fitting size Model VQZ00 VQZ00 VQZ00 Note) Purchasing order is available in units of 0 pieces. C C4 C6 C8 C0 VVQ000-50A-C VVQ000-50A-C4 VVQ000-50A-C6 VVQ000-5A-C4 VVQ000-5A-C6 VVQ000-5A-C6 VVQ000-5A-C8 VVQ000-5A-C8 VVQ000-5A-C0 M5 (VQZ00 only) VVQ000-50A-M5 <Gasket and screw assembly> Model VQZ00 VQZ00 VQZ00 <Plug connector assembly> DC: SY00-0-4A- 00 VAC: SY00-0-A- 00 VAC: SY00-0-A- Other AC voltages: SY00-0-A- Without lead wire: SY00-0-A Lead wire length Nil 00 mm mm 000 mm 500 mm 000 mm 500 mm 000 mm 5000 mm How to Order Include the connector assembly part number together with the part number for the plug connector s solenoid valve without connector. Example) In case of 000 mm of lead wire DC VQZ5-5LO-M5 SY00-0-4A-0 AC VQZ5-LO-M5 SY00-0-A-0 Part no. VQZ00-GS-5 VQZ00-GS-5 VQZ00-GS-5 Note) Above part number consists of 0 units. Each unit has one gasket and two screws. Purchasing order is available in units of 0 pieces. <Sub-plate> Model VQZ00 VQZ00 VQZ00 (with connector and sockets only) Sub-plate part no. VQZ00-S-0(R) 0 VQZ00-S- 0 (-Q) 0 VQZ00-S- (-Q) (-Q) Note) Thread type Note) R indicates external pilot type. Except VQZ00, external pilot type and internal pilot type are common K Note) <Pilot valve assembly> Note) Option Nil M V Function Symbol Specifications DC AC (0.5 W) Nil Standard B Note) High speed response type (Applicable to VQZ00/00) High pressure type (Applicable to Metal seal type, Poppet seal type) Manual override None (Applicable to VQZ00/00) Yes (Applicable to VQZ00) V5 5 G <DIN terminal type (Applicable to the VQZ00/00)> Coil voltage 00 VAC (50/60 Hz) 00 VAC (50/60 Hz) 0 VAC (50/60 Hz) 0 VAC (50/60 Hz) 4 VDC VDC Symbol DC AC G LU LOU MU MOU LZ LOZ MZ MOZ Function Symbol Specifications DC AC (0.5 W) Nil Standard B Note) High speed response type K Note) High pressure type (Metal seal type only) Note) Option Symbol Y YO YZ YS Note) YOS Note) Grommet (DC specification) L-type plug connector with lead wire L-type plug connector without connector M-type plug connector with lead wire M-type plug connector without connector Note) The electrical entry (L, M) for the VQZ00 pilot valve is different from that of the main valve model number. Valve model VQZ5-L VQZ5-M Electrical entry 5 Y Electrical entry Manual override (Applicable to the VQZ00) Coil voltage 00 VAC (50/60 Hz) 00 VAC (50/60 Hz) 0 VAC (50/60 Hz) 4 0 VAC (50/60 Hz) 5 4 VDC 6 VDC Electrical entry Pilot valve model VM-M VM-L X0 Non-locking push type Locking slotted type Light/surge voltage None Yes Electrical entry Note) For AC voltage valves there is no S option. It is already built-in to the rectifier circuit. When replacing only the pilot valve assembly, use caution because it is not possible to convert to a V5 (DIN terminal) from a V (Grommet, L-type, M-type), or vice versa. Nil B DIN terminal DIN terminal without connector DIN terminal with light/surge voltage DIN terminal with surge voltage (DC specification) DIN terminal with surge voltage, without connector (DC specification) Light/surge voltage None Yes Yes (Without light)

12 Series VQZ Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by labels of "", "Warning" or "Danger". To ensure safety, be sure to observe ISO 444 Note ), JIS B 870 Note ) and other safety practices. Explanation of the Labels Labels Danger Warning Explanation of the labels In extreme conditions, there is a possible result of serious injury or loss of life. Operator error could result in serious injury or loss of life. Operator error could result in injury Note ) or equipment damage. Note 4) Note ) ISO 444: Pneumatic fluid power General rules relating to systems Note ) JIS B 870: General Rules for Pneumatic Equipment Note ) Injury indicates light wounds, burns and electrical shocks that do not require hospitalization or hospital visits for long-term medical treatment. Note 4)Equipment damage refers to extensive damage to the equipment and surrounding devices. Selection/Handling/Applications. The compatibility of the pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications. Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications or post analysis and/or tests to meet the specific requirements. The expected performance and safety assurance are the responsibility of the person who has determined the compatibility of the system. This person should continuously review the suitability of all items specified, referring to the latest catalog information with a view to giving due consideration to any possibility of equipment failure when configuring a system.. Only trained personnel should operate pneumatically operated machinery and equipment. Compressed air can be dangerous if handled incorrectly. Assembly, handling or repair of the systems using pneumatic equipment should be performed by trained and experienced operators. (Understanding JIS B 870 General Rules for Pneumatic Equipment, and other safety rules are included.). Do not service machinery/equipment or attempt to remove components until safety is confirmed.. Inspection and maintenance of machinery/equipment should only be performed once measures to prevent falling or runaway of the driven objects have been confirmed.. When equipment is removed, confirm the safety process as mentioned above. Turn off the supply pressure for this equipment and exhaust all residual compressed air in the system, and release all the energy (liquid pressure, spring, condenser, gravity).. Before machinery/equipment is restarted, take measures to prevent quick extension of a cylinder piston rod, etc. 4. If the equipment will be used in the following conditions or environment, please contact SMC first and be sure to take all necessary safety precautions.. Conditions and environments beyond the given specifications, or if product is used outdoors.. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical equipment, food and beverages, recreation equipment, emergency stop circuits, clutch and brake circuits in press applications, or safety equipment.. An application which has the possibility of having negative effects on people, property, requiring special safety analysis. 4. If the products are used in an interlock circuit, prepare a double interlock style circuit with a mechanical protection function for the prevention of a breakdown. And, examine the devices periodically if they function normally or not. Exemption from Liability. SMC, its officers and employees shall be exempted from liability for any loss or damage arising out of earthquakes or fire, action by a third person, accidents, customer error with or without intention, product misuse, and any other damages caused by abnormal operating conditions.. SMC, its officers and employees shall be exempted from liability for any direct or indirect loss or damage, including consequential loss or damage, loss of profits, or loss of chance, claims, demands, proceedings, costs, expenses, awards, judgments and any other liability whatsoever including legal costs and expenses, which may be suffered or incurred, whether in tort (including negligence), contract, breach of statutory duty, equity or otherwise.. SMC is exempted from liability for any damages caused by operations not contained in the catalogs and/or instruction manuals, and operations outside of the specification range. 4. SMC is exempted from liability for any loss or damage whatsoever caused by malfunctions of its products when combined with other devices or software. Back page

13 Series VQZ Specific Product Precautions Be sure to read this before handling. For Safety Instructions and Port Solenoid Valve Precautions, refer to Precautions for Handling Pneumatic Devices (M-0-EA). Manual Override Without an electric signal for the solenoid valve the manual override is used for switching the main valve. Push type is standard. Locking type (Tool required) is available as an option.. VQZ00 Push type Locking type (Tool required) Press in the direction of the arrow. Turn 90 in the direction of arrow. How to Use L/M-Type Plug Connector. Attaching and detaching connectors To attach a connector, hold the lever and connector unit between your fingers and insert straight onto the pins of the solenoid valve and remove the pawl from the groove by pushing the lever downward with your thumb, and pull the connector straight out. Light/Surge Voltage Suppressor. L/M-type plug connector <DC> Cover Groove Pin Connector Cover Groove Pin - + Hook ( ) (+) Lever DC polarity indication Socket Part no. DXT70-7- Lead wire Varistor ( ) (+) Coil. VQZ00/00 <AC> Push type (Tool required) +- Push down on the manual override button with a small screwdriver until it stops. Release the screwdriver and the manual override will return. Varistor. DIN terminal <DC> With surge voltage (YS, YOS) LED Coil Locking type (Tool required) Push down completely on the manual override button with a small screwdriver. While down, turn clockwise 90 to lock it. Turn it counterclockwise to release it. Varistor Light/surge voltage (YZ) Coil +- Locked position Coil PUSH LOCK Varistor Precautions When operating with a screwdriver, turn it gently using a watchmaker s screwdriver. (Torque: less than 0. Nm) Press and rotate to lock the manual operation of VQZ00/00. If rotate without pressing, manual breakage and air leakage could be occurred. <AC> With light (YZ) Varistor Coil NL: Neon light Note) Surge voltage of varistor has residual voltage corresponding to the protective element and rated voltage; therefore, protect the controller side from the surge. Back page

14 Series VQZ Specific Product Precautions Be sure to read this before handling. For Safety Instructions and Port Solenoid Valve Precautions, refer to Precautions for Handling Pneumatic Devices (M-0-EA). Light/Surge Voltage Suppressor. Surge voltage countermeasures When shutting off the DC power supply using an emergency circuit breaker, the valve may operate incorrectly due to surge voltage generated by other electric parts (e.g., the solenoid). To ensure that surge does not affect the valve, take anti-surge measures (diode for surge protection, etc.) or use a valve with diode to prevent reverse current. (Contact SMC for model numbers.) Circuit example w Valve Valve Lead Wire Connection. Attaching and detaching sockets with lead wires Attaching Insert the sockets into the square holes of the connector (, indication), and continue to push the sockets all the way in until they lock by hooking into the seats in the connector. (When they are pushed in, their hooks open and they are locked automatically.) Then, confirm that they are locked by pulling lightly on the lead wires. Detaching To detach a socket from a connector, pull out the lead wire while pressing the socket s hook with a stick having a thin tip (approx. mm). If the socket will be used again, first spread the hook outward. Socket Connector Socket Solenoid load q e Circuit breaker DC power supply Core wire crimping area q, e: Examples of anti-surge measures w: Valve equipped with diode to prevent reverse current Lead Wire Connection. Crimping of lead wires and sockets Not necessary if ordering the lead wire pre-connected model. Strip. to.7 mm at the end of the lead wires, insert the ends of the core wires evenly into the sockets, and then crimp with a crimping tool. When this is done, take care that the coverings of the lead wires do not enter the core wire crimping area. Crimping area Core wire 0. to 0. mm Max. cover diameter: ø.7 mm Lead wire Hook Manual override (Orange) Lead wire. When replacing a conventional type valve with a new type for maintenance or other reasons, a conversion connector assembly is necessary to convert the connector from terminals to terminals and must be ordered separately. (When ordering, refer to the below part nos.) For pilot valves, there is no compatibility between the conventional type and new type. When replacing a pilot valve, be sure to confirm whether it is the new type or the conventional type. [Conventional] Pilot Valve Replacement Hook Crimping tool part no. DXT Back page Insulation [New] Manual override (Blue) Pilot valve (V) Adapter plate Pilot valve (VQ) Adapter plate Conversion connector assembly VQZ000V-85-A Coil voltage 4/ VDC 00 VAC 00 VAC 4 Other AC voltages

15 Series VQZ Specific Product Precautions Be sure to read this before handling. For Safety Instructions and Port Solenoid Valve Precautions, refer to Precautions for Handling Pneumatic Devices (M-0-EA). How to Use DIN Terminal. EN C (Former DIN 4650C) The DIN terminal type with an IP65 enclosure is protected against dust and water, however, it must not be used in water.. Connection ) Loosen the holding screw and pull the connector out of the solenoid valve terminal block. ) After removing the holding screw, insert a flat head screwdriver, etc. into the notch on the bottom of the terminal block and pry it open, separating the terminal block and the housing. ) Loosen the terminal screws (slotted screws) on the terminal block, insert the cores of the lead wires into the terminals according to the connection method, and fasten them securely with the terminal screws. 4) Secure the cord by fastening the ground nut.. Changing the entry direction After separating the terminal block and housing, the cord entry can be changed by attaching the housing in the desired direction (4 directions at 90 intervals). When equipped with a light, be careful not to damage the light with the cord s lead wires. 4. Precautions Plug in and pull out the connector vertically without tilting to one side. 5. Compatible cable Cable O.D.: ø.5 to ø7 (Reference) 0.5 mm, -core or -core, equivalent to JIS C 06 Ground nut Tightening torque Set screw.65 to.5 Nm Tightening torque Washer 0. to 0.4 Nm Tightening torque 0. to 0.5 Nm Grommet (Rubber) (Rating symbol) Refer to the table. Terminal screw ( locations) Housing (Light mounting location) Terminal block Notch Without light Rated voltage All voltages With light Rated voltage 4 VDC VDC 00 VAC 00 VAC 0 VAC (5 VAC) 0 VAC (0 VAC) DIN Connector Part No. Fitting and Silencer Part No. for P, R Ports When Using Valve as an Individual Unit Part no. for one-touch fitting for (P) port and silencer/one-touch fitting for (R) port Series VQZ00 VQZ00 VQZ00 Voltage symbol None Voltage symbol 4 V V 00 V 00 V 0 V 0 V Circuit diagram with light AC circuit NL:Neon light R: Resistor () One-touch fitting for (P) port KQH06-M5 KQS06-0S KQH08-0S DC circuit NL R LED R Silencer AN0-M5 INA-5-46 AN0-0 Part no. SY00-8- Part no. SY SY SY SY SY SY LED:Light emitting diode R: Resistor () For (R) port One-touch fitting KJS04-M5 IN-457- (for ø6) KQH06-0S The diameter of the above fitting and silencer is the maximum diameter to in the EXH port. () Silencer () One-touch fitting Back page 4

16 Series VQZ Specific Product Precautions 4 Be sure to read this before handling. For Safety Instructions and Port Solenoid Valve Precautions, refer to Precautions for Handling Pneumatic Devices (M-0-EA). One-touch Fittings Replacement The built-in fittings on the manifold can be changed easily. Simply remove the corresponding valve and take out the fitting clip underneath. Take out the clip with a screwdriver, etc., then replace the fittings. About mounting the fittings, after inserting the fitting until it stops, then put the clip into the prescribed position. Fitting assembly Fitting assembly Valve Mounting. After confirming the gasket is correctly placed under the valve, securely tighten the bolts with the proper torque shown in the table below. Model VQZ00 VQZ00 VQZ00 Proper tightening torque 0. to 0.9 N m 0.5 to 0.5 N m 0.5 to 0.7 N m Screw Clip VQZ00: Horizontally clipped to the valve body VQZ00/00: Vertically clipped to the valve body Clip Clip VQZ00 Piping Direction Replacement. How to replace the port direction Fitting and port plug are modules. After removing the clip with a flat head screwdriver, take out the fitting and port plug. The piping direction (side or top) can be altered by exchanging the fitting and port plug. During exchange, insert the fitting and the port plug until they contact the wall, then, insert the clip to specified position. Fitting Fitting assembly Port plug (VVQZ00-CP) Precautions When pulling the fitting assembly away from the valve base, remove the clip, then connect a tube or plug (KQP-) with the one-touch fitting and pull it out holding the tube or plug. Do not hold the release bushing to avoid damage.. Removing DIN Rail Removal/Mounting ) Loosen the clamp screw on the side of both ends of the manifold. ) Lift the side of the manifold off the DIN rail and slide it in the direction of the side.. Mounting ) Catch the hook of the DIN rail bracket on the side on the DIN rail. ) Push side onto the DIN rail and tighten the clamp screw. The proper tightening torque for screws is 0. to 0.4 Nm. Back page 5 Clamp bracket Clamp screw.8 Precautions The clip length for the valve and the base are different. Fitting may detach if the incorrect clip is used..valve piped on top can be operated independently by using PR plate. (Refer to the below part numbers when placing an order.) PR plate 6.8 Clip VQZ00-A (Standard) VQZ00-B (External pilot type) set screws are included.

17 Record of changes B edition Page, 9 Correction of Solenoid Specifications and Flow Characteristics Page 4, 0 Correction of Construction Page 5 to 7, Page to, Page to, Page 7 to 0 Correction of Dimensions Page 4 Addition of Made to Order LX Safety Instructions Be sure to read Precautions for Handling Pneumatic Devices (M-0-EA) before using. Akihabara UDX 5F, 4-4-, Sotokanda, Chiyoda-ku, Tokyo 0-00, JAPAN Phone: Fax: URL SMC Corporation All Rights Reserved Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. D-DN st printing KY printing LX 500DN Printed in Japan. This catalog is printed on recycled paper with concern for the global environment.