Air Cylinder. CG1 Series. Female rod end available as standard. Rod end types suitable for the application can be selected.

Transcription

1 ir Cylinder Series ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 RoHS emale rod end available as standard Rod end types suitable for the application can be selected. emale thread Easy fine adjustment of auto switch position ine adjustment of the auto switch position is possible by simply loosening the screw attached to the auto switch. Transparent switch bracket improves visibility of indicator LED. ine adjustment of auto switch Selectable Male thread No trunnion mounting female thread added to basic type variation No foreign matter accumulation due to the simple construction No trunnion mounting female thread CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 LED color indicator Screw attached to auto switch Switch bracket 287 D- -X Technical Data

2 ir Cylinder Part numbers with rod end bracket and/or pivot bracket available Not necessary to order a bracket for the applicable cylinder separately Note) Mounting bracket is shipped together with the product, but not assembled. Pivot bracket Nil None Pivot bracket is shipped together N with the product, but not assembled. pplicable to only mounting D, U and T. Example) CDG1 N: Kit of pivot bracket and clevis D N20-50Z- N W -M9W Mounting Kit of pivot bracket and trunnion Rod end bracket Nil None V Single knuckle joint W Double knuckle joint With rod end bracket V: Single W: Double knuckle joint knuckle joint Various mounting bracket options Suitable mounting brackets can be selected for the installation condition. Improved amount of mounting freedom D: Clevis N: Pivot bracket asic T: Head trunnion G: Head flange V: Single knuckle joint W: Double knuckle joint : Rod flange U: Rod trunnion L: xial foot L: xial foot asic (No trunnion mounting female thread) Mounting brackets, accessories, and nut material: Stainless steel The following accessories need to be prepared separately. (Please order separately.) Refer to the ccessories page of each series for details. ore size Single Double oot knuckle joint knuckle joint 20, 25, 32, 40, 50, 63, 80, 100 Except bore size 20 and 25. Mounting nut Rod ccessories end nut page p Easy fine adjustment of auto switch position ine adjustment of the auto switch set position can be performed by loosening the auto switch attached screw without loosening the auto switch mounting band. Operability improved compared with the current auto switch set position adjustment, where the complete switch mounting band requires loosening. Switch bracket Switch holder Visibility of the indicator LED improved with the transparent resin switch bracket (Standard specification) Screw attached to auto switch uto switch No environmental hazardous substances used Compliant with EU RoHS directive. Lead free bushing is used as sliding material. Specifications, performance and mounting method are same as the current product. Grease is selectable. (Option) Grease for food processing equipment (XC85) PTE grease (X446) Water resistant compact auto switch now available Solid state auto switch D-M9 (V) uto switch mounting screw uto switch mounting band 288

3 Stroke Variations ore size Series Standard stroke Series Variations Standard -Z Non-rotating rod K-Z or details about the clean series, refer to the Pneumatic Clean Series (CT.E02-23). ore size Variations Series ction Type Cushion With Clean Page ir-hydro rod boot series Double acting Double acting Double acting Single rod Double rod Single rod Single (Spring return acting /extend) Single rod Rubber bumper ir cushion Rubber bumper ir cushion Rubber bumper Rubber bumper ir cushion Page 292 Page 310 Page 318 Page 325 CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Double acting Double rod Rubber bumper Page 330 Direct mount R-Z Double acting Single rod Rubber bumper ir cushion Page 334 Direct mount, Non-rotating rod KR-Z Double acting Single rod Rubber bumper Page 339 With end lock Double acting Single rod Rubber bumper ir cushion Page 343 Smooth Cylinder Y-Z Double acting Single rod Rubber bumper est Pneumatics No. 2-3 Low friction Q Short type Standard series Double acting Single rod Rubber bumper Use the new series Smooth Cylinder Y Series to realize both-direction low friction and low-speed operation. (Refer to the est Pneumatics No. 2-3.) Page D- -X Technical Data

4 Combinations of Standard Products and Made to Order Specifications Series V : Standard : Made to Order v : Special product (Please contact SMC for details.) : Not available Note 1) ø40 to ø63 only Note 2) Without bumper Note 3) ø32 to ø100 only Note 4) SV type only (Heat resistant grease is used.) Note 5) ø20 to ø63 only Note 6) Single acting/spring return type (S) only Note 7) The products with an auto switch are not compatible. (Standard type) K (Non-rotating rod type) Double acting Single acting Double acting Single rod Double rod Single rod Single rod Double rod Rubber ir Rubber ir Rubber Rubber ir Rubber Page 292 Page 310 Page 318 Page 325 Page 330 Symbol Specifications pplicable bore size ø20 to ø100 ø20 to ø40 ø20 to ø63 ø40 to ø63 ø20 to ø63 Standard Standard V V V V V V V V Long st Long stroke ø20 to ø100 Note 10) Note 10) Note 10) V V V V v V V V D uilt-in magnet V V V V V V V V l With One-touch fittings Note 15) ø20 to ø63 V v v v v v v v l-l J K With rod boot ø20 to ø100 Note 11) Note 11) Note 11) Note 11) V V V V v v v v lh ir-hydro type ø20 to ø63 V V 10-, 11- Clean series ø20 to ø100 Note 1) Note 1) V V V V v 25- Note 9) Copper (Cu) and Zinc (Zn)-free Note 15) ø20 to ø100 V V v v v v v v 20- Note 9) Copper Note 8) and luorine-free ø20 to ø100 V V V V v V v V l R V Water resistant ø32 to ø100 V V V V v lm Cylinder with stable lubrication function (Lube-retainer) ø20 to ø100 V v v v X6 Heat resistant cylinder ( 10 to 150 C) Note 7) Note 2) Note 2) v X7 Cold resistant cylinder ( 40 to 70 C) Note 7) Note 2) Note 2) v Note 5) v v ø20 to ø100 X9 Low speed cylinder (10 to 50 mm/s) v v v X13 Low speed cylinder (5 to 50 mm/s) v v v XC4 With heavy duty scraper ø32 to ø63 v v v XC6 Made of stainless steel ø20 to ø100 Note 6) XC8 djustable stroke cylinder/djustable extension type v v XC9 djustable stroke cylinder/djustable retraction type v v XC10 Dual stroke cylinder/double rod type ø20 to ø63 v XC11 Dual stroke cylinder/single rod type v XC12 Tandem cylinder Note 15) v v v XC13 uto switch rail mounting ø20 to ø100 v v v XC20 Head cover axial port ø20 to ø63 v v XC22 XC27 luororubber seal Double clevis and double knuckle joint pins made of stainless steel Series ction/ Type Cushion Page ø20 to ø100 Note 2) Note 2) v v v v v v v XC29 Double knuckle joint with spring pin Note 6) v v v v v XC35 With coil scraper v v v XC37 Larger throttle diameter of connection port ø20 to ø63 v v v v XC42 uilt-in shock absorber in head cover side v v v XC85 Grease for food processing equipment ø20 to ø100 v v v X446 PTE grease ø20 to ø100 v v v 290

5 Series Use the new series Smooth Cylinder Y Series to realize both-direction low friction and low-speed operation. (Refer to the est Pneumatics No. 2-3.) R KR (Direct mount, (Direct mount type) Non-rotating rod type) Note 15) (With end lock) Note 12) ly (Smooth Cylinder) lq (Low friction type) Double acting Double acting Double acting Double acting Double acting Single rod Single rod Single rod Single rod Single rod Rubber ir Rubber Rubber ir Page 334 Page 339 Page 343 est Pneumatics No. 2-3 Page 354 ø20 to ø63 ø20 to ø63 ø20 to ø100 ø20 to ø100 ø20 to ø100 Symbol V V V V V V V Standard Note 10) v v v V V V V Long st V V V V V V V D v v v v v v v l v v v V V v v l-l J K v lh V v v v 10-, 11- v v v v v v v 25- V V v v v 20- v v v v l R V v v lm Note 2) Note 2) Note 15) Note 15) Note 15) v v X6 v X7 v v v X9 v X13 v v v v XC4 v v XC6 Note 15) Note 13) Note 13) v v v v v XC8 Note 15) Note 14) Note 14) v v v v v XC9 v v v v v v v XC10 v v v v v v v XC11 v v v v v XC12 Note 2) v v v v XC13 Note 15) v v v v XC20 v v v XC22 Note 9) Note 9) CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 v v v v v v XC27 v v v v v v v XC29 v v v v XC35 v v v v v v v XC37 v v v v v XC42 v v v XC85 X446 Note 8) Copper-free for the externally exposed part. or details, refer to the Web Catalog. Note 9) or details, refer to the Web Catalog. Note 10) Long stroke is beyond the performance guarantee. Note 11) emale rod end is available as a special order. Note 12) or details about the smooth cylinder, refer to the est Pneumatics No Note 13) vailable only for locking at head end. Note 14) vailable only for locking at rod end. Note 15) The shape is the same as the current product. 291 D- -X Technical Data

6 With auto switch Series N 20 How to Order 100 CDG1 N Z With auto switch (uilt-in magnet) ore size Mounting mm asic mm Z* asic (without trunnion mounting female thread) mm L xial foot mm Rod flange mm G Head flange mm U* Rod trunnion mm T* Head trunnion mm D Clevis * Not available for ø80 and ø100. Type * Mounting bracket is shipped together with N Rubber bumper the product, but not assembled. ir cushion * The cylinder for, G, L, D mounting types is Z: asic (without trunnion mounting female thread). Port thread type Rubber bumper ir cushion Nil Rc ø20 to ø100 M5 x 0.8 ø20, ø25 Rc ø32 to ø100 TN NPT ø20 to ø100 NPT * ø32 to ø100 T M5 x 0.8 ø20, ø25 G ø32 to ø100 G ø32 to ø100 * Not available for ø20 and ø25. Solid state auto switch Reed auto switch Indicator light ir Cylinder: Standard Type Double cting, Single Rod Z Pivot bracket Nil None Pivot bracket is shipped together N with the product, but not assembled * Only for D, U, T mounting types * Pivot bracket is shipped together with the product, but not assembled. Rod end bracket Nil None V Single knuckle joint W Double knuckle joint Rod end thread Nil Male rod end emale rod end Cylinder stroke Refer to Standard Strokes on page 293. M9W RoHS ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Made to Order or details, refer to page 293. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. uto switch Nil Without auto switch * or applicable auto switches, refer to the table below. * No bracket is provided for the female rod end. * Rod end bracket is shipped together with the product, but not assembled. * knuckle joint pin is not provided with the single knuckle joint. Suffix for cylinder (Rod boot) Nil Without rod boot J Nylon tarpaulin K Heat resistant tarpaulin * In the case of w/rod boot, and a foot bracket or rod flange as a bracket, those parts are to be assembled at the time of shipment. * or female rod end, no rod boot is provided. * Refer to Ordering Example of Cylinder ssembly on page 294. pplicable uto Switches/Refer to pages 1575 to 1701 for further information on auto switches. uto switch model Load voltage Lead wire length (m) Special Electrical Wiring pplicable bore size Pre-wired pplicable Type function entry (Output) ø20 to ø63 ø80, ø None connector load DC C Perpendicular In-line In-line (Nil) (M) (L) (Z) (N) M9NV M9N 3-wire (NPN) G59 IC 5 V, 12 V Grommet M9PV M9P circuit 3-wire (PNP) G5P M9V M9 2-wire 12 V K59 Connector H7C M9NWV M9NW 3-wire (NPN) G59W IC Relay, Yes 24 V 5 V, 12 V Diagnostic indication M9PWV M9PW circuit PLC 3-wire (PNP) (2-color indicator) G5PW M9WV M9W 2-wire 12 V Grommet K59W 3-wire (NPN) M9NV*1 M9N*1 IC 5 V, 12 V Water resistant 3-wire (PNP) M9PV*1 M9P*1 circuit (2-color indicator) M9V*1 M9*1 2-wire 12 V G5*1 With diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V H7N G59 IC circuit 3-wire (Equiv. to NPN) 5 V 96V 96 IC circuit Yes 100 V 93V*2 93 Grommet No 100 V or less 90V 90 IC circuit Yes 2-wire 24 V 12 V 100 V, 200 V 54 Relay, No 200 V or less 64 PLC Yes C73C Connector No 24 V or less C80C IC circuit Diagnostic indication (2-color indicator) Grommet Yes 59W *1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. water-resistant type cylinder is recommended for use in an environment which requires water resistance. However, please contact SMC for water-resistant cylinder of ø20 and ø25. *2 1 m type lead wire is only applicable to D-93. * Lead wire length symbols: 0.5 m Nil (Example) M9NW 5 m Z (Example) M9NWZ * Solid state auto switches marked with are 1 m M (Example) M9NWM None N (Example) H7CN produced upon receipt of order. 3 m L (Example) M9NWL * Since there are other applicable auto switches than listed above, refer to page 361 for details. * or details about auto switches with pre-wired connector, refer to pages 1648 and * The D-9ll/M9lll auto switches are shipped together, (but not assembled). (However, only the auto switch mounting brackets are assembled before shipment.) 292

7 ir Cylinder: Standard Type Double cting, Single Rod Series Specifications Symbol Rubber bumper Symbol -X446 PTE grease Made to Order Click here for details ir cushion Made to Order: Individual Specifications (or details, refer to page 362.) Specifications Symbol Specifications -Xl Change of rod end shape -X6 Heat resistant cylinder ( 10 to 150 C) 1 -X7 Cold resistant cylinder ( 40 to 70 C) 2 -X9 Low speed cylinder (10 to 50 mm/s) -X13 Low speed cylinder (5 to 50 mm/s) -XC4 With heavy duty scraper -XC6 Made of stainless steel -XC8 djustable stroke cylinder/djustable extension type -XC9 djustable stroke cylinder/djustable retraction type -XC10 Dual stroke cylinder/double rod type -XC11 Dual stroke cylinder/single rod type -XC12 Tandem cylinder -XC13 uto switch rail mounting -XC20 Head cover axial port -XC22 luororubber seal 1 -XC27 Double clevis and double knuckle joint pins made of stainless steel -XC29 Double knuckle joint with spring pin -XC35 With coil scraper -XC37 Larger throttle diameter of connection port -XC42 uilt-in shock absorber in head cover side -XC85 Grease for food processing equipment 1 Cylinders with rubber bumper have no bumper. 2 Only compatible with cylinders with rubber bumper, but has no bumper. Refer to pages 355 to 361 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Cylinder mounting bracket, by stroke/uto switch mounting surfaces Precautions Refer to page before handling. ore size ction Double acting, Single rod Lubricant luid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Not required (Non-lube) R: Rod side, H: Head side Cylinder sizes ø80 and ø100 do not have basic (without trunnion mounting female thread), rod trunnion and head trunnion types. oot, flange and clevis types of cylinder sizes from ø20 to ø63 do not have trunnion mounting female thread. Operate the cylinder within the allowable kinetic energy. ir 1.5 MPa 1.0 MPa 0.05 MPa Without auto switch: 10 C to 70 C (No freezing) With auto switch : 10 C to 60 C Piston speed 50 to 1000 mm/s 50 to 700 mm/s Stroke length tolerance Up to 1000 st mm, mm Up to 1500 st Cushion Rubber bumper, ir cushion Mounting llowable kinetic energy (J) Rubber bumper ir cushion Mounting Male rod end emale rod end Male rod end emale rod end asic, asic (without trunnion mounting female thread), xial foot, Rod flange, Head flange, Rod trunnion, Head trunnion, Clevis R: 0.35 R: 0.56 H: 0.42 H: ccessories/refer to page 309 for part numbers and dimensions. asic xial foot Rod flange Head flange Rod Head trunnion trunnion Clevis Standard Rod end nut V V V V V V V Clevis pin V Single knuckle joint V V V V V V V Double knuckle joint Option (with pin) 2 V V V V V V V Pivot bracket 1 V 1 V 1 V Rod boot V V V V V V V 1 Not available for ø80 and ø double knuckle joint pin and retaining rings are shipped together. 3 Stainless steel mounting brackets and accessories are also available. Refer to page for details. Standard Strokes ore size Standard stroke Note1) Maximum manufacturable stroke Note 2) 20 25, 50, 75, 100, 125, 150, to , 50, 75, 100, 125, 50, , 200, 250, to Note 1) Intermediate strokes not listed above are produced upon receipt of order. Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) The maximum manufacturable stroke shows the long stroke. Note 3) pplicable strokes should be confirmed according to the usage. or details, refer to ir Cylinders Model Selection on front matter pages. In addition, the products that exceed the standard stroke might not be able to fulfill the specifications due to the deflection etc. 293 CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 D- -X Technical Data C

8 Series Ordering Example of Cylinder ssembly Rod oot Material Cylinder model: CDG1DN20-100Z-NW-M9W uto switch Mounting D: Clevis Pivot bracket N: Yes Rod end bracket W: Double knuckle joint uto switch D-M9W: 2 pcs. Clevis Pivot bracket Symbol Rod boot material Maximum operating temperature J Nylon tarpaulin 70 C K Heat resistant tarpaulin 110 C Maximum ambient temperature for the rod boot itself. Pivot bracket, double knuckle joint and auto switch are shipped together with the product, but not assembled. Double knuckle joint Mounting rackets/part No. Mounting bracket q ty Order ore size Contents xial foot 2 Note) CG-L020 CG-L025 CG-L032 CG-L040 CG-L050 CG-L063 CG-L080 CG-L100 2 foots, 8 mounting bolts lange 1 CG-020 CG-025 CG-032 CG-040 CG-050 CG-063 CG-080 CG flange, 4 mounting bolts Trunnion pin 1 CG-T020 CG-T025 CG-T032 CG-T040 CG-T050 CG-T063 2 trunnion pins, 2 trunnion bolts, 2 flat washers Clevis 1 CG-D020 CG-D025 CG-D032 CG-D040 CG-D050 CG-D063 CG-D080 CG-D100 1 clevis, 4 mounting bolts, 1 clevis pin, 2 retaining rings Pivot bracket 1 CG CG CG CG CG CG CG CG pivot bracket Note) Order two foots per cylinder. Mounting rackets, ccessories/material, Surface Treatment Segment Description Material Surface treatment oot Carbon steel Nickel plating lange Carbon steel (ø20 to ø63) Nickel plating Cast iron (ø80, ø100) Nickel plating Mounting Carbon steel (ø20 to ø63) Nickel plating Clevis brackets Cast iron (ø80, ø100) Nickel plating Trunnion pin Carbon steel Salt-bath nitrocarburizing Trunnion pin Trunnion bolt Carbon steel Nickel plating lat washer Carbon steel Nickel plating Rod end nut Carbon steel Zinc chromated Single knuckle joint Carbon steel (ø20 to ø32) Nickel plating Cast iron (ø40 to ø100) Zinc chromated Double knuckle joint Carbon steel (ø20 to ø32) Nickel plating Cast iron (ø40 to ø100) Zinc chromated ccessories Knuckle pin Carbon steel Clevis pin Carbon steel Pivot bracket Carbon steel (ø20 to ø63) Nickel plating Cast iron (ø80, ø100) Nickel plating Mounting bolt Carbon steel Nickel plating Retaining ring Carbon tool steel Phosphate coating Mounting Procedure Mounting procedure for trunnion ollow the procedures below when mounting a pivot bracket on the trunnion. Trunnion bolt (With scotch grip) 4 or 5 times remounting Cylinder body possible ø20 to ø63 lat washer Trunnion pin (Put grease on the exterior.) Pivot bracket Mounting procedure for clevis ollow the procedures below when mounting a pivot bracket on the clevis. ø20 to ø63 Retaining ring Clevis pin (Put grease) Cylinder body Pivot bracket Retaining ring ø80, ø100 Retaining Clevis pin ring (Put grease) Cylinder Retaining body ring Pivot bracket 294

9 Pipe O.D. øpd ir Cylinder: Standard Type Double cting, Single Rod Series Weights (kg) ore size asic () asic (Z) xial foot lange Trunnion Clevis Pivot bracket Single knuckle joint Double knuckle joint (with pin) dditional weight per 50 mm of stroke dditional weight for switch magnet dditional weight with air cushion Weight reduction for female rod end dditional weight for long stroke asic weight Calculation (Example) CDG1N20-100Z (uilt-in magnet, lange, ø20, 100 stroke) uilt-in One-touch ittings (The shape is the same as the current product.) Mounting type N ore size Stroke This type has the One-touch fittings integrated in a cylinder, which enables to reduce the piping labor and installing space dramatically. øhd HH uilt-in One-touch fittings Dimensions (Dimensions other than those shown below are the same as the standard type.) ore size G G HD HH PD (12) (12) (12) Note) ( ): Long stroke Oasic weight 0.18 kg (lange, ø20) Odditional weight for stroke 0.05 kg/50 mm Oir cylinder stroke 100 mm Odditional weight for switch magnet 0.01 kg x (100/50) = 0.29 kg Specifications ore size 20, 25, 32, 40, 50, 63 ction Double acting luid Maximum operating pressure Minimum operating pressure Piston speed Cushion Mounting uto switch can be mounted. emale rod end is not available. Use the current seal kit. pplicable Tubing O.D./I.D. ore size pplicable tubing O.D. 6/4 6/4 6/4 8/6 10/7.5 10/7.5 Can be used for either nylon, pplicable tubing material soft nylon or polyurethane tubing. ir 1.0 MPa 0.05 MPa 50 to 750 mm/s Rubber bumper asic, xial foot, Rod flange, Head flange, Rod trunnion, Head trunnion, Clevis (used for changing the port location by 90 ) CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Clean Series 10- Mounting type Type (Cushion) ore size Stroke Rod end thread Z Clean Series (With relief port) The type which is applicable for using inside the clean room graded ISO Class 4 by making an actuator s rod section a double seal construction and discharging by relief port directly to the outside of clean room. or details about the clean series, refer to the Pneumatic Clean Series (CT.E02-23). Specifications ore size 20, 25, 32, 40, 50, 63, 80, 100 ction Double acting luid ir Maximum operating pressure 1.0 MPa Minimum operating pressure 0.05 MPa Cushion Rubber bumper, ir cushion Piston speed 30 to 400 mm/s Relief port size M5 x 0.8 Mounting asic, xial foot, Rod flange, Head flange uto switch can be mounted. The basic type is type only. However, no trunnion mounting female thread is provided. 295 D- -X Technical Data

10 Series ir-hydro CDG1 Mounting type Nil Without magnet D uilt-in magnet Low pressure hydraulic cylinder of 1.0 MPa or less When using together with the CC series air-hydro unit, constant and low speed actuation and intermediate stopping similar to hydraulic units are possible with the use of valves and other pneumatic equipment. Dimensions (Dimensions other than those shown below are the same as the standard type.) S + Stroke Water Resistant T ore size G T S ZZ Male thread emale thread Made to Order -X Specifications ore size 20, 25, 32, 40, 50, 63 ction Double acting luid Turbine oil Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.18 MPa Piston speed 15 to 300 mm/s Cushion Rubber bumper (Standard equipment) mbient and fluid temperature 5 to 60 C asic, xial foot, Rod flange, Head Mounting flange, Rod trunnion, Head trunnion, Clevis Made to Order Change of rod end shape uto switch can be mounted. CDG1 Mounting type Type ore size Port thread type R Stroke Rod end thread Z Pivot bracket Rod end bracket Nil D Without magnet uilt-in magnet Water resistant cylinder R NR seals (Nitrile rubber) V KM seals (luororubber) Caution Since the scraper is press-fit into the rod cover, it cannot be replaced. pplicable for use in an environment with water splashing such as food processing and car wash equipment, etc. H ore size Stroke Rod end thread Z Pivot bracket Rod end bracket ir-hydro Water resistant 2-color indicator, solid state auto switch M9 (V) ø32 to ø63 G5L ø80, ø100 Made to Order Specifications XC6 ore size 32, 40, 50, 63, 80, 100 ction Double acting, Single rod Cushion uto switch mounting Made to Order uto switch uto switch Rubber bumper/ir cushion and mounting type XC6: Made of stainless steel Specifications other than above are the same as standard type. Dimensions (Dimensions other than those shown below are the same as the standard type.) With rubber bumper G (E1) øe With air cushion W G (E1) øe (1) T S + Stroke (1) T S + Stroke ore G ZZ (E1) E (1) S T W size Rc NPT G Male thread emale thread (85) (127) 93 (101) (93) (145) 101 (110) (109) (169) 115 (127) (109) (169) 115 (127) (130) (204) 138 (152) (131) (205) 142 (156) Dimensions marked with are the same as the standard type. ( ): Denotes the dimensions for long stroke. Refer to page 1125 for details. 296

11 ir Cylinder: Standard Type Double cting, Single Rod Series Cylinder with Stable Lubrication unction (Lube-retainer) CDG1 Mounting N ore size M Stroke Rod end thread Z Pivot bracket Rod end bracket uto switch With auto switch (uilt-in magnet) * No trunnion mounting female thread is provided on the rod side. (or : asic) G 2 x P Refer to the Web Catalog for details. Cylinder with Stable Lubrication unction (Lube-retainer) Specifications Dimensions (Dimensions other than those shown below are the same as the standard type.) ction ore size 20, 25, 32, 40, 50, 63, 80, 100 Minimum operating pressure Cushion Double acting, Single rod 0.1 MPa Rubber bumper * Specifications other than the above are the same as the standard type. ore size G P M5 x M5 x (12) (Rc 1/8) 40 (13) (Rc 1/8) 50 (14) (Rc 1/4) 63 (14) (Rc 1/4) 80 (20) (Rc 3/8) 100 (20) (Rc 1/2) * When female thread is used, use a washer, etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. ( ): Same as the standard model. * The mounting dimensions of the mounting bracket are the same as the standard type. CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 297 D- -X Technical Data

12 Series Construction With rubber bumper ø80, ø100 y!0 r!9 q y w o Long stroke ø80, ø100 r y e u i u With air cushion Long stroke 1001 to r!9 q!5 w!1 Component Parts No. Description Material Note 1 Rod cover luminum alloy Hard anodized 2 Tube cover luminum alloy Hard anodized 3 Piston luminum alloy 4 Piston rod Stainless steel or ø20 or ø25 with built-in magnet Carbon steel Hard chrome plating 5 ushing earing alloy 6 umper Resin ø32 or larger is 7 umper Resin common. 8 Retaining ring Stainless steel Except ø80 and ø100 9 Wear ring Resin 10 Rod end nut Carbon steel Zinc chromated 11 Cushion ring luminum alloy 12 Cushion ring luminum alloy 13 Seal retainer Rolled steel Zinc chromated 14 Cushion valve ø40 or smaller Carbon steel Electroless nickel plating ø50 or larger Steel wire Zinc chromated Note) or cylinders with auto switches, the magnet is installed in the piston. The material for ø20, ø25 cylinders with auto switches is made of stainless steel. 298 Replacement Parts: Seal Kit Long stroke No. Description Material Note 15 Cushion seal Urethane ø32 or larger is 16 Cushion seal Urethane common. 17 Head cover luminum alloy Hard anodized 18 Cylinder tube luminum alloy Hard anodized 19 Rod seal NR 20 Piston seal NR 21 Tube gasket NR 22 Valve seal NR ore size Kit no. Contents 20 N20Z-PS 25 N25Z-PS 32 N32Z-PS Set of 40 N40Z-PS Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. Note) Refer to the Specific Product Precautions on page for Disassembly/Replacement. Order with the kit number according to the bore size. The seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-010 (10 g)

13 ir Cylinder: Standard Type Double cting, Single Rod Series asic: N Width across flats K MM H1 ød G 2 x P (Rc, NPT, G) G R0.4 2 x TC C C N With air cushion 10 Wθ 8 x J øe Width across flats 1 L H R0.4 K T W G 4 x TC øi S + Stroke 2 x P (Rc, NPT, G) Cushion valve, Width across flats WH T W G øe N TG TC thread detail øtd TE T CJ1 CJP CJ2 JCM CM2 CM3 JM M asic (Without trunnion mounting female thread): ZN Width across flats K MM H1 ød G 2 x P (Rc, NPT, G) G R0.4 M1 C2 CS1 øe øi øe CS2 Width across flats 1 L H R0.4 K S + Stroke ore Stroke range Rc, NPT port G port size Standard Long stroke G G P G G P L 1 C D E H H1 I J K K MM 20 Up to to (12) 1/ (12) M5 x M4 x 0.7 depth M8 x Up to to (12) 1/ (12.5) M5 x M5 x 0.8 depth M10 x Up to to (12) 1/ (10.5) 1/ M5 x 0.8 depth M10 x Up to to (13) 1/ (10) 1/ M6 x 1 depth M14 x Up to to (14) 1/ (14) 1/ M8 x 1.25 depth M18 x Up to to (14) 1/ (14) 1/ M10 x 1.5 depth M18 x Up to to (20) 3/ (17.5) 3/ M10 x 1.5 depth M22 x Up to to (20) 1/ (17.5) 1/ M12 x 1.75 depth M26 x 1.5 With ir Cushion TC Thread ore size N S T T ZZ ore size Rc, NPT port G G P W W W θ WH (77) (114) (12) M5 x (16) (77) (119) (12.5) M5 x (16) (79) (11) 113 (121) (12) 1/ (16) (87) (12) 130 (139) (13) 1/ (17) (102) (13) 150 (162) (14) 1/ (18) (102) (13) 150 (162) (14) 1/ (18) (122) 182 (196) (20) 3/ (24) (122) 182 (196) (20) 1/ (24) 20 4 Note) ( ): Denotes the dimensions for long stroke. ore size TC TD TE T TG 20 M5 x M6 x M8 x M10 x M12 x M14 x * Cylinder sizes ø80 and ø100 do not have trunnion mounting female thread on the width across flats N. 299 D- -X Technical Data

14 Series asic: N With rod boot JH øij øe øij øe JW l f h + l ZZ + l + Stroke l f h + l ZZ + l + Stroke ø20 to ø63 ø80, ø100 With Rod oot ore e f h IJ JH JW size (Reference) (Reference) l ZZ (134) (141) (143) (159) (182) (182) (205) (205) * The minimum stroke with rod boot is 20 mm. 1 /4 stroke emale rod end MM Thread depth 1 H emale Rod End ore size 1 H MM ZZ M4 x (92) M5 x (93) M6 x 1 87 (95) M8 x (104) M10 x (120) M10 x (120) M14 x (144) M16 x (147) * When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. 300

15 ir Cylinder: Standard Type Double cting, Single Rod Series xial oot: LN C LH 4 x øld 15 8 x J C LX LZ Width across flats K MM Width across flats 1 H1 L H ød Z K G S + Stroke 2 x P Width across flats N (Rc, NPT, G) LT øi G W W 2 x ølc X Y (Knock pin position) Y X LS + Stroke M CJ1 CJP CJ2 JCM CM2 With air cushion 10 Wθ W G 2 x P (Rc, NPT, G) Cushion valve, Width across flats WH W G CM3 JM M With rod boot h + l 8 8 h + l 8 M1 C2 CS1 JH øij øe øij øe CS2 JW l f Z + l ZZ + l + Stroke (122) (206) (20) 1/ (24) 20 4 * or female rod end, since the wrench flap (K and K portions) will be inside of the bracket when the piston rod is retracted at the stroke end, extend the piston rod to tighten the nut using a tool, and mount a workpiece on the rod end. * Refer to the basic type for the female rod end. Note) ( ): Denotes the dimensions for long stroke. l f Z + l ZZ + l + Stroke ø80, ø100 ore Stroke range Rc, NPT port G port size Standard Long stroke G G P G G P L 1 C D H H1 I J K KLC LD LH LS LT LX LZ M MM 20 Up to to (12) 1/ (12) M5 x M4 x (53) M8 x Up to to (12) 1/ (12.5) M5 x M5 x (53) M10 x Up to to (12) 1/ (10.5) 1/ M5 x (53) M10 x Up to to (13) 1/ (10) 1/ M6 x (60) M14 x Up to to (14) 1/ (14) 1/ M8 x (67) M18 x Up to to (14) 1/ (14) 1/ M10 x (67) M18 x Up to to (20) 3/ (17.5) 3/ M10 x (74) M22 x Up to to (20) 1/ (17.5) 1/ M12 x (74) M26 x 1.5 With ir Cushion ore ore Rc, NPT port N S W X Y Z ZZ size size G G P (77) (118) (77) (123.5) (79) (125.5) (87) (144) (102) (169.5) (102) (169.5) (122) (202.5) (12) M5 x (16) (12.5) M5 x (16) (12) 1/ (16) (13) 1/ (17) (14) 1/ (18) (14) 1/ (18) (20) 3/ (24) 20 4 With Rod oot ore W W Wθ WH size e f h IJ JH JW (Reference) (Reference) l Z ZZ (138) (145.5) (147.5) (164) (189.5) (189.5) (211.5) (215) * The minimum stroke with rod boot is 20 mm. 1 /4 stroke 301 D- -X Technical Data

16 øi Series Rod lange: N 4 x ød 8 x J Width across flats K MM T G 2 x P (Rc, NPT, G) G R0.4 H1 ød L H K 10 Wθ W G W G JH øij øe øij øe X±0.15 C 0 øe øe 0.05 Width across flats 1 C X±0.15 Width across flats N S + Stroke * End boss is machined on the flange for øe. With air cushion 2 x P (Rc, NPT, G) Cushion valve, Width across flats WH With rod boot JW With ir Cushion ore Rc, NPT port size G G P l f h + l ZZ + l + Stroke M26 x (122) 182 (196) (20) 1/ (24) 20 4 * or female rod end, since the wrench flap (K and K portions) will be inside of the bracket when the piston rod is retracted at the stroke end, extend the piston rod to tighten the nut using a tool, and mount a workpiece on the rod end. * Refer to the basic type for the female rod end. Note) ( ): Denotes the dimensions for long stroke. l f h + l ZZ + l + Stroke ø80, ø100 ore Stroke range Rc, NPT port G port size Standard Long stroke G G P G G P L 1 C D E D T X H H1 I J K 20 Up to to (12) 1/ (12) M5 x M4 x Up to to (12) 1/ (12.5) M5 x M5 x Up to to (12) 1/ (10.5) 1/ M5 x Up to to (13) 1/ (10) 1/ M6 x Up to to (14) 1/ (14) 1/ M8 x Up to to (14) 1/ (14) 1/ M10 x Up to to (20) 3/ (17.5) 3/ M10 x Up to to (20) 1/ (17.5) 1/ M12 x ore size K MM N S ZZ 20 6 M8 x (77) 106 (114) 25 8 M10 x (77) 111 (119) M10 x (79) 113 (121) M14 x (87) 130 (139) M18 x (102) 150 (162) M18 x (102) 150 (162) M22 x (122) 182 (196) (12) M5 x (16) (12.5) M5 x (16) (12) 1/ (16) (13) 1/ (17) (14) 1/ (18) (14) 1/ (18) (20) 3/ (24) 20 4 With Rod oot ore W W Wθ WH e f h IJ JH JW size (Reference) (Reference) l ZZ (134) (141) (143) (159) (182) (182) (205) (205) * The minimum stroke with rod boot is 20 mm. 1 /4 stroke

17 ir Cylinder: Standard Type Double cting, Single Rod Series Head lange: GN Width across flats K 0 øe 0.05 MM H1 ød G 2 x P (Rc, NPT, G) øi G 0 øe x ød 8 x J X±0.15 C CJ1 CJP Width across flats 1 With air cushion L H R0.4 K W G Width across flats N S + Stroke 2 x P (Rc, NPT, G) Cushion valve, Width across flats WH W G T C X±0.15 * End boss is machined on the flange for øe. JH Wθ 10 CJ2 JCM CM2 CM3 JM M M1 With rod boot C2 CS1 øij øe øij øe CS2 JW l f h + l ZZ + l + Stroke l f h + l ZZ + l + Stroke ø80, ø100 ore Stroke range Rc, NPT port G port size Standard Long stroke G G P G G P L 1 C D E D T X H H1 I J K 20 Up to to (12) 1/ (12) M5 x M4 x Up to to (12) 1/ (12.5) M5 x M5 x Up to to (12) 1/ (10.5) 1/ M5 x Up to to (13) 1/ (10) 1/ M6 x Up to to (14) 1/ (14) 1/ M8 x Up to to (14) 1/ (14) 1/ M10 x Up to to (20) 3/ (17.5) 3/ M10 x Up to to (20) 1/ (17.5) 1/ M12 x With ir Cushion ore ore Rc, NPT port K MM N S ZZ size size G G P 20 6 M8 x (77) 112 (120) 25 8 M10 x (77) 118 (126) M10 x (79) 120 (128) M14 x (87) 138 (147) M18 x (102) 159 (171) M18 x (102) 159 (171) M22 x (122) 193 (207) M26 x (122) 196 (210) * Refer to the basic type for the female rod end. Note) ( ): Denotes the dimensions for long stroke (12) M5 x (16) (12.5) M5 x (16) (12) 1/ (16) (13) 1/ (17) (14) 1/ (18) (14) 1/ (18) (20) 3/ (24) (20) 1/ (24) 20 4 With Rod oot W W Wθ WH ore e f h IJ JH JW size (Reference) (Reference) l ZZ (140) (148) (150) (167) (191) (191) (216) (219) * The minimum stroke with rod boot is 20 mm. 1 /4 stroke 303 D- -X Technical Data

18 Series Rod Trunnion: UN 2 x øtde8 (Pin O.D) TR MM H L H1 K øi ød G T S + Stroke 2 x P Width across flats N (Rc, NPT, G) G R0.4 TZ Width across flats 1 Width across flats K Z 10 Wθ W G W G h + l l f JH øij øe 0 øe øe 0.05 R0.4 * Constructed of a trunnion pin, flat washer and hexagon socket head cap bolt. With air cushion 2 x P (Rc, NPT, G) Cushion valve, Width across flats WH With rod boot JW 8 8 Z + l ZZ + l + Stroke ore Stroke range Rc, NPT port G port size Standard Long stroke G G P G G P L 1 D E H H1 I K K MM N S 20 Up to to (12) 1/ (12) M5 x M8 x (77) 25 Up to to (12) 1/ (12.5) M5 x M10 x (77) 32 Up to to (12) 1/ (10.5) 1/ M10 x (79) 40 Up to to (13) 1/ (10) 1/ M14 x (87) 50 Up to to (14) 1/ (14) 1/ M18 x (102) 63 Up to to (14) 1/ (14) 1/ M18 x (102) With ir Cushion With Rod oot ore ore Rc, NPT port ore T TDe8 TR TZ Z ZZ W W Wθ WH e f h IJ JH JW size size G G P size (Reference) (Reference) l Z ZZ (134) (141) (143) (159) (114) (12) M5 x (16) (119) (12.5) M5 x (16) (121) (12) 1/ (16) (139) (13) 1/ (17) (162) (14) 1/ (18) (162) (14) 1/ (18) 20 3 * Refer to the basic type for the female rod end. Note) ( ): Denotes the dimensions for long stroke (182) (182) * The minimum stroke with rod boot is 20 mm. 1 /4 stroke 304

19 ir Cylinder: Standard Type Double cting, Single Rod Series Head Trunnion: TN MM 0 øe 0.05 Width across flats 1 Width across flats K L H1 H K ød R0.4 G S + Stroke 2 x P (Rc, NPT, G) øi Width across flats N Z + Stroke G T R0.4 0 øe x øtde8 (Pin O.D) * Constructed of a trunnion pin, flat washer and hexagon socket head cap bolt. TR TZ CJ1 CJP CJ2 JCM CM2 CM3 With air cushion W G 2 x P (Rc, NPT, G) Cushion valve, Width across flats WH W G h + l l f JH øij øe Wθ 10 JM M M1 C2 With rod boot CS1 CS2 JW 8 8 Z + l + Stroke ZZ + l + Stroke ore Stroke range Rc, NPT port G port size Standard Long stroke G G P G G P L 1 D E H H1 I K K MM N S 20 Up to to (12) 1/ (12) M5 x M8 x (77) 25 Up to to (12) 1/ (12.5) M5 x M10 x (77) 32 Up to to (12) 1/ (10.5) 1/ M10 x (79) 40 Up to to (13) 1/ (10) 1/ M14 x (87) 50 Up to to (14) 1/ (14) 1/ M18 x (102) 63 Up to to (14) 1/ (14) 1/ M18 x (102) With ir Cushion With Rod oot ore ore Rc, NPT port ore T TDe8 TR TZ Z ZZ W W Wθ WH size G G P size e f h IJ JH JW l size (Reference) (Reference) Z ZZ (121) 126 (134) (128) 133 (141) (130) 135 (143) (145) 150 (159) (101) 106 (114) (12) M5 x (16) (106) 111 (119) (12.5) M5 x (16) (11) (108) 113 (121) (12) 1/ (16) (12) (125) 130 (139) (13) 1/ (17) (13) (147) 150 (162) (14) 1/ (18) (13) (147) 150 (162) (14) 1/ (18) 20 3 * Refer to the basic type for the female rod end. Note) ( ): Denotes the dimensions for long stroke (167) 170 (182) (167) 170 (182) * The minimum stroke with rod boot is 20 mm. 1 /4 stroke 305 D- -X Technical Data

20 ød øi Series Clevis: DN (ø20 to ø63) MM L H K G S + Stroke 2 x P (Rc, NPT, G) G L RR øcdh10 (Hole dia.) d9 (Shaft dia.) CZ C TT H1 C Width across flats 1 Width across flats K Width across flats N Z + Stroke 8 x J TZ W G W G Wθ 10 h + l 8 8 JH øij øe 0 øe 0.05 R0.4 With air cushion 2 x P (Rc, NPT, G) Cushion valve, Width across flats WH With rod boot JW l f Z + l + Stroke ZZ + l + Stroke Stroke range Rc, NPT port G port ore size Standard Long stroke G G P G G P L 1 C CD CZ D E H H1 I J K K L MM N 20 Up to to (12) 1/ (12) M5 x M4 x M8 x Up to to (12) 1/ (12.5) M5 x M5 x M10 x Up to to (12) 1/ (10.5) 1/ M5 x M10 x Up to to (13) 1/ (10) 1/ M6 x M14 x Up to to (14) 1/ (14) 1/ M8 x M18 x Up to to (14) 1/ (14) 1/ M10 x M18 x With ir Cushion With Rod oot ore pplicable ore Rc, NPT port ore RR S TT TZ Z ZZ W W Wθ WH size G G P size e f h IJ JH JW size pin part no. (Reference) (Reference) l Z ZZ (77) (126) 129 (137) CD-G (12) M5 x (16) (146) 149 (157) (77) (133) 138 (146) CD-G (12.5) M5 x (16) (155) 160 (168) (79) (139) 146 (154) CD-G (12) 1/ (16) (161) 168 (176) (87) (159) 168 (177) CD-G (13) 1/ (17) (179) 188 (197) (102) (185) 193 (205) CD-G (14) 1/ (18) (205) 213 (225) (102) (190) 200 (212) CD-G (14) 1/ (18) (210) 220 (232) * Refer to the basic type for the female rod end. Note) ( ): Denotes the dimensions for long stroke. 306 * The minimum stroke with rod boot is 20 mm. 1 /4 stroke

21 ir Cylinder: Standard Type Double cting, Single Rod Series Clevis: DN (ø80, ø100) MM L H1 H K ød S + Stroke L G 2 x P G V (Rc, NPT, G) RR øcdh10 (Hole dia.) d9 (Shaft dia.) TZ CZ C CJ1 CJP 0 øe 0.05 R0.4 Width across flats K øi Width across flats N C 8 x J CX CJ2 JCM CM2 Width across flats 1 Z + Stroke CM3 With air cushion W G 2 x P (Rc, NPT, G) Cushion valve, Width across flats WH W G Wθ 10 JM M M1 C2 CS1 h + l 8 øij øe CS2 With rod boot l f Z + l + Stroke ZZ + l + Stroke ore Stroke range Rc, NPT port G port size Standard Long stroke G G P G G P L 1 C CD CX CZ D E H H1 I J K K L MM N 80 Up to to (20) 3/ (17.5) 3/ M10 x M22 x Up to to (20) 1/ (17.5) 1/ M12 x M26 x ore pplicable RR S TZ V Z ZZ size pin part no (122) (228) 232 (246) IY-G (122) (236) 244 (258) IY-G10 * Refer to the basic type for the female rod end. Note) ( ): Denotes the dimensions for long stroke. With ir Cushion ore Rc, NPT port size G G P (20) 3/ (24) (20) 1/ (24) 20 4 With Rod oot ore W W Wq WH e f h IJ l Z ZZ size D /4 223 (237) 241 (255) stroke 231 (245) 253 (267) -X * The minimum stroke with rod boot is 20 mm. 307 Technical Data

22 Series With Pivot racket [( ): Denotes the dimensions for long stroke.] Rod Trunnion (U) with Pivot racket TS racket mounting range TT TH TT TT TH TX TV 4 x øt øte 0 Z TY TW Male Thread emale Thread ore size TE T TH TS TT TV TW TX TY Z ore size Z Head Trunnion (T) with Pivot racket TS racket mounting range TH Clevis (D) with Pivot racket ø20 to ø63 Z + Stroke Male Thread emale Thread ore size TE T TH TS TT TV TW TX TY Z ZZ ore size Z ZZ (101) 114 (122) ( 79) 92 (100) (106) 119 (127) ( 80) 93 (101) (108) 125 (132) ( 82) 99 (106) (125) 146 (153) ( 90) 111 (118) (147) 168 (179) (105) 126 (137) (147) 173 (184) (105) 131 (142) TY TW TX TV 4 x øt øte Clevis (D) with Pivot racket ø80, ø100 Z + Stroke Z + Stroke TY TW TY TW TT 4 x øt TX TV TX TV TH 4 x øt øte Male Thread emale Thread ore size TE T TH TT TV TW TX TY Z ZZ ore size Z ZZ (126) 139 (147) (104) 117 (125) (133) 146 (154) (107) 120 (128) (139) 155 (163) (113) 129 (137) (159) 178 (187) (124) 143 (152) (185) 205 (217) (143) 163 (175) (190) 215 (227) (148) 173 (185) Male Thread emale Thread ore size T TH TT TV TW TX TY Z ZZ ore size Z ZZ (228) (286.5) (176) (234.5) (236) (312.5) (187) (263.5)

23 ø Series Dimensions of ccessories Single Knuckle Joint I-G02, G03 Material: Carbon steel ø Material: Carbon steel L2 L1 I-G04, G05, G08, G10 Material: Cast iron Part no. pplicable bore Included Dd9 L1 size d L2 m t retaining ring IY-G Type C8 for axis IY-G03 25, Type C10 for axis IY-G Type C10 for axis IY-G05 50, Type C14 for axis IY-G Type C18 for axis IY-G Type C22 for axis * Retaining rings are included. ø ø pplicable bore Part no. size 1 E1 L1 MM R1 U1 NDH10 NX I-G M8 x I-G03 25, M10 x I-G ø22 30 M14 x I-G05 50, ø28 40 M18 x I-G ø38 50 M22 x I-G ø44 55 M26 x Knuckle Pin Clevis Pin Double Knuckle Joint Y-G02, G03 Material: Carbon steel MM E1 ø20 to ø63 R1 NX Material: Carbon steel ø ønd hole H10 xis d9 NZ L ø MM E1 Y-G04, G05, G08, G10 Material: Cast iron x ø R1 ønd hole H10 xis d9 NX NZ L 1 U1 1 U1 L1 L1 Part pplicable bore size 1 E1 L1 MM R1 U1 ND NX NZ L Included no. pin part no. Y-G M8 x IY-G02 Y-G03 25, M10 x IY-G03 Y-G ø22 30 M14 x IY-G04 Y-G05 50, ø28 40 M18 x IY-G05 Y-G ø38 50 M22 x IY-G08 Y-G ø44 55 M26 x IY-G10 * knuckle pin and retaining rings are included. Pivot racket. ø Knock pin hole CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Material: Carbon steel ø L2 L1 Part no. pplicable bore Included Dd9 L1 size d L2 m t retaining ring CD-G Type C8 for axis CD-G Type C10 for axis CD-G Type C12 for axis CD-G Type C14 for axis CD-G Type C16 for axis CD-G Type C18 for axis * Retaining rings are included. * clevis pin and a knuckle pin are common for the bore size ø80 and ø100. Rod End Nut Material: Carbon steel Part no. pplicable bore size d H1 1 C D NT M8 x (15) 12.5 NT-03 25, 32 M10 x (19.6) 16.5 NT-G04 40 M14 x (21.9) 18 NT-05 50, 63 M18 x (31.2) 26 NT M22 x (37.0) 31 NT M26 x (47.3) 39 ø ø ø80, ø100 Material: Cast iron ø ø x ø Part no. pplicable bore size T Td TE T TH TN TR TT CG (29.3) CG (33.1) CG (40.4) CG (49.2) CG (60.4) 24 6 CG (74.6) 26 8 CG CG Part no. pplicable bore size TU TV TW TX TY TZ pplicable pin O.D. CG (18.1) (35.8) d CG (20.7) (39.8) d CG (23.6) (49.4) d CG (27.3) (58.4) d CG (29.7) (72.4) d CG (34.3) (90.4) d CG d CG d D- -X Technical Data

24 Series Mounting rackets, Rod End rackets, and Nut Material: Stainless Steel Part No. ore size xial foot*1 Single knuckle joint Double knuckle joint*1 Rod end nut 20 I-G02SUS Y-G02SUS NT-02SUS CG-L032SUS I-G03SUS Y-G03SUS NT-03SUS 40 CG-L040SUS I-G04SUS Y-G04SUS NT-G04SUS 50 CG-L050SUS 63 CG-L063SUS I-G05SUS Y-G05SUS NT-05SUS 80 CG-L080SUS I-G08SUS Y-G08SUS NT-08SUS 100 CG-L100SUS I-G10SUS Y-G10SUS NT-10SUS *1 knuckle pin and retaining rings are shipped together. Refer to the XC27 for details on stainless steel double clevis pins and double knuckle pins. The accessories need to be ordered separately from the cylinder. Dimensions The single knuckle joint, double knuckle joint, mounting nut, and rod end nut are the same as the standard type. xial foot LH LX LZ 4 x øld Z X Y LT Y X M ore size LD LH LT LX LZ M X Y Z ZZ [25] [3] [44] 60 [3.5] [16] 6 [53] [117.5(125.5)] [30] [3] [54] 75 [4] [16.5] 6.5 [63.5] [135(144)] [10] [40] 4 [66] [75.5] [157.5(169.5)] [12] [45] 4 [82] [75.5] 159(171) [55] 4 [100] [95] 190(204) [14] [70] [6] [120] [30] 15 [95] 193(207) *1 [ ]: Same as the standard type ( ): Denotes the dimensions for long strokes *2 Supplied with 4 mounting screws

25

26 ir Cylinder: Standard Type Double cting, Double Rod W Series RoHS ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 W CDG1W With auto switch 100 With auto switch (uilt-in magnet) Double acting, Double rod type Mounting asic Z asic (without trunnion mounting female thread) L xial foot lange U Trunnion Not available for ø80 and ø100. Mounting bracket is shipped together with the product, but not assembled. The cylinder for, L mounting types is Z: asic (without trunnion mounting female thread). L L N N Type N Rubber bumper ir cushion mm mm mm mm ore size mm mm mm mm 100 Z Z uto switch Nil Without auto switch or applicable auto switches, refer to the table below. Suffix for cylinder (Rod boot) Nil Without rod boot One J Nylon tarpaulin side K Heat resistant tarpaulin oth JJ Nylon tarpaulin sides KK Heat resistant tarpaulin Rod end thread uilt-in Magnet Cylinder Model Nil Male rod end If a built-in magnet cylinder without an auto switch is required, emale rod end there is no need to enter the symbol for the auto switch. (Example) CDG1W32-100Z Cylinder stroke Refer to Standard Strokes on page 311. pplicable uto Switches/Refer to pages 1575 to 1701 for further information on auto switches. Indicator light M9W Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Note) In the case of w/rod boot, and a foot bracket or rod flange as a bracket, those parts are to be assembled at the time of shipment. or female rod end, no rod boot is provided. Made to Order or details, refer to page 311. Load voltage uto switch model Lead wire length (m) Type Special function Electrical Wiring pplicable bore size Pre-wired entry pplicable load (Output) None DC C ø20 to ø63 ø80, ø100 connector (Nil) (M) (L) (Z) (N) Perpendicular In-line In-line 3-wire M9NV M9N V V V v v (NPN) G59 V V v v IC 5 V, 12 V 3-wire M9PV M9P V V V v v circuit Grommet (PNP) G5P V V v v M9V M9 V V V v v 2-wire 12 V K59 V V v v Connector H7C V V V V 3-wire M9NWV M9NW V V V v v (NPN) G59W V V v v IC Relay, Diagnostic Yes 24 V 5 V, 12 V 3-wire M9PWV M9PW V V V v v circuit PLC indication (PNP) G5PW V V v v (2-color indicator) M9WV M9W V V V v v 2-wire 12 V Grommet K59W V V v v 3-wire (NPN) M9NV 1 M9N 1 v v V v v IC 5 V, 12 V Water resistant 3-wire (PNP) M9PV 1 M9P 1 v v V v v circuit (2-color indicator) M9V 1 M9 1 v v V v v 2-wire 12 V G5 1 V v v Diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V H7N V V v v IC circuit 3-wire (Equiv. to NPN) 5 V 96V 96 V V IC circuit Yes 100 V 93V 2 93 V V V V Grommet No 100 V or less 90V 90 V V IC circuit Yes 2-wire 24 V 12 V 100 V, 200 V 54 V V V Relay, No 200 V or less 64 V V PLC Yes C73C V V V V Connector No 24 V or less C80C V V V V IC circuit Diagnostic indication (2-color indicator) Grommet Yes 59W V V Solid state auto switch Reed auto switch 1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please consult with SMC regarding water resistant types with the above model numbers. 2 1 m type lead wire is only applicable to D-93. Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ How to Order Solid state auto switches marked with are produced upon receipt of order. None N (Example) H7CN Since there are other applicable auto switches than listed above, refer to page 361 for details. or details about auto switches with pre-wired connector, refer to pages 1648 and The D-9ll/M9lll auto switches are shipped together, (but not assembled). (However, only the auto switch mounting brackets are assembled before shipment.) 310

27 ir Cylinder: Standard Type Double cting, Double Rod W Series Specifications Symbol Rubber bumper ir cushion Made to Order Click here for details Symbol Specifications -Xl Change of rod end shape -X6 Heat resistant cylinder ( 10 to 150 C) 1 -X7 Cold resistant cylinder ( 40 to 70 C) 2 -XC6 Made of stainless steel -XC13 uto switch rail mounting -XC22 luororubber seal 1 -XC37 Larger throttle diameter of connection port -XC85 Grease for food processing equipment 1 Cylinders with rubber bumper have no bumper. 2 Only compatible with cylinders with rubber bumper, but has no bumper. Rod oot Material Symbol Rod boot material Maximum operating temperature J Nylon tarpaulin 70 C K Heat resistant tarpaulin 110 C Maximum ambient temperature for the rod boot itself. Refer to pages 355 to 361 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Cylinder mounting bracket, by stroke/ uto switch mounting surfaces Precautions Refer to page before handling. ore size ction Double acting, Double rod Lubricant luid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Not required (Non-lube) R: Rod side, H: Head side Rod trunnion type is not available for ø80 and ø100. oot and flange types of cylinder sizes from ø20 to ø63 do not have trunnion mounting female thread. Operate the cylinder within the allowable kinetic energy. ir 1.5 MPa 1.0 MPa 0.08 MPa Without auto switch: 10 C to 70 C (No freezing) With auto switch : 10 C to 60 C Piston speed 50 to 1000 mm/s 50 to 700 mm/s Stroke length tolerance Up to 1000 st mm, +1.8 mm Up to 1500 st 0 Cushion Rubber bumper, ir cushion Mounting asic, asic (without trunnion mounting female thread), xial foot, lange, Trunnion llowable kinetic energy (J) Rubber bumper ir cushion Male rod end emale rod end Male rod end emale rod end R: 0.35 R: 0.56 H: 0.42 H: ccessories/refer to page 309 for part numbers and dimensions. Mounting asic xial foot Rod flange Rod trunnion Standard Rod end nut V V V V Option Single knuckle joint V V V V Double knuckle joint 2 (with pin) V V V V Pivot bracket 1 V 1 Rod boot V V V V 1 Not available for ø80 and ø double knuckle joint pin and retaining rings are shipped together. 3 Stainless steel mounting brackets and accessories are also available. Refer to page for details. Standard Strokes ore size Standard stroke Note1) Maximum manufacturable stroke Note 2) 20 25, 50, 75, 100, 125, 150, to , , 50, 75, 100, 125, 150, 200, 250, to 1500 Note 1) Intermediate strokes not listed above are produced upon receipt of order. Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) The maximum manufacturable stroke shows the long stroke. Note 3) pplicable strokes should be confirmed according to the usage. or details, refer to ir Cylinders Model Selection on front matter pages. In addition, the products that exceed the standard stroke might not be able to fulfill the specifications due to the deflection etc. 311 CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 D- -X Technical Data C

28 W Series Weights asic weight ore size asic xial foot lange Trunnion Pivot bracket Single knuckle joint Double knuckle joint (with pin) dditional weight per 50 mm of stroke dditional weight with air cushion Weight reduction for female rod end Calculation (Example) WLN32-100Z (oot, ø32, 100 stroke) (kg) Oasic weight 0.49 (oot, ø32) Odditional weight 0.13/50 stroke Oir cylinder stroke 100 stroke 0.49 x 0.13 x 100/50 = 0.75 kg Mounting rackets/part No. Mounting Order ore size Contents bracket q ty xial foot 2 Note) CG-L020 CG-L025 CG-L032 CG-L040 CG-L050 CG-L063 CG-L080 CG-L100 2 foots, 8 mounting bolts lange 1 CG-020 CG-025 CG-032 CG-040 CG-050 CG-063 CG-080 CG flange, 4 mounting bolts 2 trunnion pins, 2 trunnion bolts, Trunnion pin 1 CG-T020 CG-T025 CG-T032 CG-T040 CG-T050 CG-T063 2 flat washers Pivot bracket 1 CG CG CG CG CG CG pivot bracket Note) Order two foots per cylinder. 312

29 ir Cylinder: Standard Type Double cting, Double Rod W Series Construction With rubber bumper ø80, ø100 y i r!2 t!4 q w y!3 e u With air cushion!5!0 i r!2 t!4 q!1 w o!3 e CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Component Parts No. Description Material Note 1 Rod cover luminum alloy Hard anodized 2 Cylinder tube luminum alloy Hard anodized 3 Piston luminum alloy 4 Piston rod Stainless steel or ø20 or ø25 with built-in magnet Carbon steel * Hard chrome plating * 5 ushing earing alloy 6 umper Resin 7 umper Resin ø32 or larger is common. 8 Rod end nut Carbon steel Zinc chromated 9 Cushion ring luminum alloy 10 Cushion valve ø40 or smaller Carbon steel Electroless nickel plating ø50 or larger Steel wire Zinc chromated 11 Cushion seal Urethane 12 Rod seal NR 13 Piston seal NR 14 Tube gasket NR 15 Valve seal NR Note) or cylinders with auto switches, the magnet is installed in the piston. * The material for ø20, ø25 cylinders with auto switches is made of stainless steel. Replacement Parts: Seal Kit ore size Kit no. Contents 20 WN20Z-PS Set of the 25 WN25Z-PS nos. 32 WN32Z-PS!2,!3,!4 40 WN40Z-PS Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. Note) Refer to the Specific Product Precautions on page for Disassembly/Replacement. Order with the kit number according to the bore size. * The seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-010 (10 g) 313 D- -X Technical Data

30 W Series asic with Rubber umper: WN Width across flats K MM H1 G 2 x RcP G Width across flats K H1 MM C øi ød ød C N Width across flats 1 8 x J L H K T 4 x TC S + Stroke ZZ + 2 Stroke T L K H + Stroke Width across flats 1 MM Thread depth 1 øij øe l f h + l ZZ + l + Stroke H JH øij øe øe øe R0.4 R0.4 <With rod boot on one side> emale rod end 8 8 ZZ + 2 Stroke <With rod boot on both sides> JW h + l l f S + Stroke ZZ + 2 ( l + Stroke) f l + Stroke h + l + Stroke ore Stroke range size Standard Long stroke L 1 C D E G H1 I J K K MM N P S 20 Up to to M4 x 0.7 depth M8 x / Up to to M5 x 0.8 depth M10 x / Up to to M5 x 0.8 depth M10 x / Up to to M6 x 1 depth M14 x / Up to to M8 x 1.25 depth M18 x / Up to to M10 x 1.5 depth M18 x / Up to to M10 x 1.5 depth M22 x / Up to to M12 x 1.75 depth M26 x /2 122 ore size T TC** Without rod boot With rod boot on one side * With rod boot * on both sides H ZZ e f h IJ JH JW (Reference) (Reference) l ZZ ZZ M5 x M6 x M8 x M10 x M12 x M14 x * The minimum stroke with rod boot is 20 mm. ** Cylinder sizes ø80 and ø100 do not have trunnion mounting female thread on the width across flats N /4 stroke emale Rod End ore size 1 H MM ZZ M4 x M5 x M6 x M8 x M10 x M10 x M14 x M16 x

31 ir Cylinder: Standard Type Double cting, Double Rod W Series asic with ir Cushion: W C 10 Wθ C N Width across flats K MM H1 øe Width across flats 1 8 x J L H ød R0.4 K W G T 2 x RcP Cushion valve, Width across flats WH øi 4 x TC S + Stroke ZZ + 2 Stroke W G 20 M8 x M5 x M5 x M10 x M5 x M6 x M10 x Rc1/ M8 x M14 x Rc1/ M10 x M18 x Rc1/ M12 x M18 x Rc1/ M14 x M22 x Rc3/ M26 x Rc1/ * Refer to w/rubber bumper for the female rod end. T ød R0.4 Width across flats K MM H1 L K H + Stroke øe Width across flats 1 or the one with rod boot, refer to w/rubber bumper. ore size Stroke range Standard Long stroke L 1 C D E G H H1 I J K K 20 Up to to M4 x 0.7 depth Up to to M5 x 0.8 depth Up to to M5 x 0.8 depth Up to to M6 x 1 depth Up to to M8 x 1.25 depth Up to to M10 x 1.5 depth Up to to M10 x 1.5 depth Up to to M12 x 1.75 depth ore size MM N P S T TC** ZZ W Wθ WH 10 Wθ * or mounting brackets, refer to page 309. ** Cylinder sizes ø80 and ø100 do not have trunnion mounting female thread on the width across flats N. CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 315 D- -X Technical Data

32 W Series With Mounting racket xial foot: WLl 15 øe LH 4 x øld LX LZ Z W X Y LT 2 ølc (Knock pin position) LS + Stroke Y W X M ore size Stroke range LC LD LH LS LT LX LZ M W X Y Z 20 Up to Up to Up to Up to Up to Up to Up to Up to * Other dimensions are the same as basic type. lange: Wl 4 x ød T X±0.15 X±0.15 H ore size Stroke range E X D T H 20 Up to Up to Up to Up to Up to Up to Up to Up to * End boss is machined on the flange for øe. * Other dimensions are the same as basic type. 316

33 ir Cylinder: Standard Type Double cting, Double Rod W Series With Mounting racket Trunnion: WUl 2 x øtde8 (Pin O.D.) TT TR TS TX TV TZ racket mounting range TH 4 x øt øte 0 Z TY TW Stroke Z ore size range TDe8 TE T TH TR TS TT TV TW TX TY TZ Without rod boot With rod boot 20 Up to (35.8) l 25 Up to (39.8) l 32 Up to (49.4) l 40 Up to (58.4) l 50 Up to (72.4) l 63 Up to (90.4) l * Constructed of a pin, flat washer and hexagon socket head cap bolt. * Other dimensions are the same as basic type. CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 317 D- -X Technical Data

34 ir Cylinder: Standard Type Single cting, Spring Return/Extend Series ø20, ø25, ø32, ø40 RoHS With auto switch With auto switch (uilt-in magnet) N 25 CDG1 N 25 Mounting asic G Head flange Z asic (without trunnion U Rod trunnion mounting female thread) T Head trunnion L xial foot D Clevis Rod flange Mounting bracket is shipped together with the product, but not assembled. The cylinder for, G, L, D mounting types is Z: asic (without trunnion mounting female thread). Cylinder stroke Refer to Standard Strokes on page 319. Type N Rubber bumper uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDG1N32-100TZ How to Order ore size mm mm mm mm ction S Single acting, Spring return T Single acting, Spring extend S S Nil V W Z Z Rod end thread Nil Male rod end emale rod end Rod end bracket None Single knuckle joint Double knuckle joint No bracket is provided for the female rod end. Rod end bracket is shipped together with the product, but not assembled. knuckle joint pin is not provided with the single knuckle joint. pplicable uto Switches/Refer to pages 1575 to 1701 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indicator) Water resistant (2-color indicator) Electrical entry Indicator light Wiring (Output) Pivot bracket Nil None N Pivot bracket is shipped together with the product. Only for D, U, T mounting types Pivot bracket is shipped together with the product, but not assembled. M9W Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. uto switch Nil Without auto switch or applicable auto switches, refer to the table below. Made to Order or details, refer to page 319. Refer to Ordering Example of Cylinder ssembly on page 320. Load voltage uto switch model Lead wire length (m) pplicable bore size DC C None (Nil) (M) (L) (Z) (N) Pre-wired connector ø20 to ø40 Perpendicular In-line M9NV M9N V V V v v IC pplicable load 3-wire (NPN) Grommet 3-wire (PNP) 5 V, 12 V M9PV M9P V V V v v circuit M9V M9 V V V v v 2-wire 12 V Connector H7C V V V V 3-wire (NPN) M9NWV M9NW V V V v v IC 5 V, 12 V Yes 3-wire (PNP) 24 V M9PWV M9PW V V V v v circuit 2-wire 12 V M9WV M9W V V V v v Grommet 3-wire (NPN) M9NV 1 M9N 1 v v V v v IC 5 V, 12 V circuit 3-wire (PNP) M9PV 1 M9P 1 v v V v v 2-wire 12 V M9V 1 M9 1 v v V v v Diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V H7N V V v v IC circuit Grommet Connector 3-wire (Equiv. to NPN) IC circuit Yes 5 V 96V 96 V V 100 V 93V 2 93 V V V V No 100 V or less 90V 90 V V IC circuit Yes 100 V, 200 V 54 V V V 12 V No 2-wire 24 V 200 V or less 64 V V Yes C73C V V V V No 24 V or less C80C V V V V IC circuit Diagnostic indication (2-color indicator) Grommet Yes 59W V V 1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please consult with SMC regarding water resistant types with the above model numbers. 2 1 m type lead wire is only applicable to D-93. Lead wire length symbols: 0.5 m Nil (Example) M9NW Solid state auto switches marked with p are produced upon receipt of order. 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) H7CN Since there are other applicable auto switches than listed above, refer to page 361 for details. or details about auto switches with pre-wired connector, refer to pages 1648 and The D-9ll/M9lll auto switches are shipped together, (but not assembled). (However, only the auto switch mounting brackets are assembled before shipment.) 318 Relay, PLC Relay, PLC

35 ir Cylinder: Standard Type Single cting, Spring Return/Extend Series Specifications Symbol Spring return, Rubber bumper Spring extend, Rubber bumper Spring return Spring extend Made to Order Click here for details Symbol Specifications -XC6 Made of stainless steel *1 -XC20 Head cover axial port *2 -XC27 Double clevis and double knuckle joint pins made of stainless steel -XC29 Double knuckle joint with spring pin *1 -XC85 Grease for food processing equipment *1 pplicable only to single acting, spring return type. or single acting, spring extend type, please contact SMC. *2 Only compatible with cylinders with rubber bumper. Refer to pages 355 to 361 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Cylinder mounting bracket, by stroke/ uto switch mounting surfaces ore size ction Single acting, Spring return Single acting, Spring extend Lubricant luid Proof pressure Maximum operating pressure Not required (Non-lube) ir 1.5 MPa 1.0 MPa Minimum operating pressure 0.18 MPa 0.23 MPa mbient and fluid temperature Piston speed Without auto switch: 10 C to 70 C (No freezing) With auto switch : 10 C to 60 C 50 to 1000 mm/s Stroke length tolerance Up to 200 st mm Cushion Rubber bumper asic, asic (without trunnion mounting female thread), Mounting xial foot, Rod flange, Head flange, Rod trunnion, Head trunnion, Clevis ccessories/refer to page 309 for part numbers and dimensions. Mounting asic xial foot Rod flange Head flange Rod Head trunnion trunnion Clevis Rod end nut V V V V V V V Standard Clevis pin V Single knuckle joint V V V V V V V Option Double knuckle joint *1 (with pin) V V V V V V V Pivot bracket V V V *1 double knuckle joint pin and retaining rings are shipped together. *2 Stainless steel mounting brackets and accessories are also available. Refer to page for details. Standard Strokes ore size Standard stroke Note1) 20 25, 50, 75, 100, , 32, 40 25, 50, 75, 100, 125, 150, 200 Note 1) Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) pplicable strokes should be confirmed according to the usage. or details, refer to ir Cylinders Model Selection on front matter pages. In addition, the products that exceed the standard stroke might not be able to fulfill the specifications due to the deflection etc. Mounting rackets/part No. Theoretical Output Refer to page Spring Reaction orce Refer to page CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Precautions Refer to page before handling. Mounting bracket Order q ty. Note) Order two foots per cylinder. ore size Contents xial foot 2 Note) CG-L020 CG-L025 CG-L032 CG-L040 2 foots, 8 mounting bolts lange 1 CG-020 CG-025 CG-032 CG flange, 4 mounting bolts Trunnion pin 1 CG-T020 CG-T025 CG-T032 CG-T040 2 trunnion pins, 2 trunnion bolts, 2 flat washers Clevis 1 CG-D020 CG-D025 CG-D032 CG-D040 1 clevis, 4 mounting bolts, 1 clevis pin, 2 retaining rings Pivot bracket 1 CG CG CG CG pivot bracket 319 D- -X Technical Data C

36 Series Ordering Example of Cylinder ssembly Cylinder model: CDG1DN20-100Z-NW-M9W Clevis uto switch Mounting D: Clevis Pivot bracket N: Yes Rod end bracket W: Double knuckle joint uto switch D-M9W: 2 pcs. Pivot bracket Pivot bracket, double knuckle joint and auto switch are shipped together with the product, but not assembled. Double knuckle joint Weights Spring return (kg) Spring extend (kg) ore size ore size st st st st st st asic asic 100 st weight weight 100 st st st st st st st xial foot xial foot Mounting lange Mounting lange bracket bracket weight Trunnion weight Trunnion Clevis Clevis Pivot bracket Pivot bracket ccessories Single knuckle joint ccessories Single knuckle joint Double knuckle joint (with pin) Double knuckle joint (with pin) Weight reduction for female rod end Weight reduction for female rod end Calculation (Example) LN20-100SZ Oasic weight 0.28 kg (ø20) (oot, ø20, 100 stroke) OMounting bracket weight 0.11 kg (oot) = 0.39 kg Calculation (Example) LN20-100TZ Oasic weight 0.26 kg (ø20) (oot, ø20, 100 stroke) OMounting bracket weight 0.11 kg (oot) = 0.37 kg 320

37 ir Cylinder: Standard Type Single cting, Spring Return/Extend Series Construction Single acting, Spring return o r t!3 q y!1!0!2!5 e i u w Single acting, Spring extend Component Parts No. Description Material Note 1 Rod cover luminum alloy Hard anodized 2 Tube cover luminum alloy Hard anodized 3 Piston luminum alloy 4 Piston rod 5 ushing earing alloy Note) or cylinders with auto switches, the magnet is installed in the piston. * The material for ø20, ø25 cylinders with auto switches is made of stainless steel. o r!4 q t!6 y!5 e i u!2!0!1!3 w Stainless steel or ø20 or ø25 with built-in magnet Carbon steel * Hard chrome plating * 6 umper Resin ø32 or larger is 7 umper Resin common. 8 Wear ring Resin 9 Rod end nut Carbon steel Zinc chromated 10 Return spring Steel wire Zinc chromated 11 Spring guide luminum alloy 12 Spring seat luminum alloy 13 Plug with breathing hole lloy steel lack zinc chromated 14 Rod seal NR 15 Piston seal NR 16 Tube gasket NR Replacement Part: Seal or single acting, spring return Part no. No. Description Material Piston seal NR N20-S-PS N25-S-PS N32-S-PS N40-S-PS Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. or single acting, spring extend Replacement parts/seal kits are the same as standard type, double acting, single rod (with rubber bumper). Refer to page 298. Note) Refer to the Specific Product Precautions on page for Disassembly/Replacement. Order with the kit number according to the bore size. * The seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-010 (10 g) CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 321 D- -X Technical Data

38 Series asic Spring return: N Width across flats K G Plug with fixed orifice RcP G MM H1 ød R0.4 C øi C N 8 J Width across flats 1 L H K T 4 x TC S + Stroke T Width across flats K G RcP Plug with fixed orifice G MM H1 C øe øe øi øe øe R0.4 Spring extend: N ød R0.4 C N Width across flats 1 8 x J L R0.4 K T 4 x TC H + Stroke ZZ + 2 Stroke S + Stroke T emale rod end MM thread depth 1 H ore size Stroke range L 1 C D E G G H H1 I J K K MM N P 20 Up to M4 0.7 depth M8 x /8 25 Up to M5 0.8 depth M10 x /8 32 Up to M5 0.8 depth M10 x /8 40 Up to M6 1 depth M14 x /8 ore size T T TC 1 to 50 st 51 to 100 st 101 to 125 st 126 to 200 st S ZZ S ZZ S ZZ S ZZ M5 x M6 x M8 x M10 x emale Rod End ore 1 to 50 st 51 to 100 st 101 to 125 st 126 to 200 st 1 H MM size ZZ ZZ ZZ ZZ M4 x M5 x M6 x M8 x

39 With Mounting racket xial foot: LN ir Cylinder: Standard Type Single cting, Spring Return/Extend Series ( ) Note) The drawings below show the single acting/spring return type. The rod is in retracted state for spring extend type. LH 4 x øld X± x ød LX LZ X± Z H W X T Y LT 2 x ølc (Knock pin position) LS + Stroke ore Stroke 1 to 50 st 51 to 100 st 101 to 125 st 126 to 200 st M LC LD LH LT LX LZ W X Y Z size range LS ZZ LS ZZ LS ZZ LS ZZ 20 Up to Up to Up to Up to Rod flange: N øe Y W X M CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Head flange: GN 0.05 øe 0 4 x ød X±0.15 H T X±0.15 ore size * End boss is machined on the flange for øe. Stroke range E X D T H 20 Up to Up to Up to Up to Rod lange ore ZZ size 1 to 50 st 51 to 100 st 101 to 125 st 126 to 200 st Head lange ore ZZ size 1 to 50 st 51 to 100 st 101 to 125 st 126 to 200 st D- -X Technical Data

40 Series With Mounting racket Rod trunnion: UN 2 x øtde8 (Pin O.D.) TR TS racket mounting range TT TH Head trunnion: TN TX TV TZ 4 x øt øte 0 Z TY TW 2 x øtde8 (Pin O.D.) TR TS racket mounting range TT TH Z + Stroke ore size Stroke range TDe8 TE T TH TR TS TT TV TW TX TY TZ 20 Up to (35.8) Up to (39.8) Up to (49.4) Up to (58.4) Rod Trunnion Head Trunnion ore ZZ ore 1 to 50 st 51 to 100 st 101 to 125 st 126 to 200 st size Z 1 to 50 st 51 to 100 st 101 to 125 st 126 to 200 st size Z ZZ Z ZZ Z ZZ Z ZZ Constructed of pins, flat washers and hexagon socket head cap bolts. Other dimensions are the same as basic type. Constructed of pins, flat washers and hexagon socket head cap bolts. Other dimensions are the same as basic type. Clevis: DN TY TW L RR øcd hole H10 xis d9 TX TV TZ CZ C±0.1 4 x øt øte 0 TT 8 x J C±0.1 TT TH Z + Stroke (The above shows the case port location is changed by 90.) Clevis ore size or dimensions of pivot bracket, refer to page 309. Other dimensions are the same as basic type. TY TW 4 x øt TX TV TZ øte 0 1 to 50 st 51 to 100 st 101 to 125 st 126 to 200 st Z ZZ Z ZZ Z ZZ Z ZZ Stroke range CD CZ L RR TE T TH TT TV TW TX TY TZ 20 Up to (35.8) Up to (39.8) Up to (49.4) Up to (58.4)

41 With auto switch Type N Rubber bumper ir cushion (ø40 to ø63 only) K N CDG1K N With auto switch (uilt-in magnet) Double acting, Non-rotating rod type Mounting asic G Head flange asic (without trunnion U Rod trunnion Z mounting female thread) T Head trunnion L xial foot D Clevis Rod flange Note) Mounting bracket is shipped together with the product, but not assembled. The cylinder for, G, L, D mounting types is Z: asic (without trunnion mounting female thread). If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDG1K32-100Z ir Cylinder: Non-rotating Rod Type Double cting K Series ø20, ø25, ø32, ø40, ø50, ø63 Cylinder stroke Refer to Standard Strokes on page 326. ore size mm mm mm mm mm mm Z Z Rod end bracket Nil None V Single knuckle joint W Double knuckle joint Rod end thread Nil Male rod end emale rod end pplicable uto Switches/Refer to pages 1575 to 1701 for further information on auto switches. Type Solid state auto switch Reed auto switch uilt-in Magnet Cylinder Model Special function Diagnostic indication (2-color indicator) Water resistant (2-color indicator) Electrical entry Grommet 2 1 m type lead wire is only applicable to D-93. Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL Indicator light Wiring (Output) 5 m Z (Example) M9NWZ None N (Example) H7CN M9W Load voltage uto switch model Lead wire length (m) pplicable bore size DC C None (Nil) (M) (L) (Z) (N) 1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please consult with SMC regarding water resistant types with the above model numbers. uto switch Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Nil Without auto switch or applicable auto switches, refer to the table below. Made to Order or details, refer to page 326. Pre-wired connector ø20 to ø63 Perpendicular In-line M9NV M9N V V V v v IC pplicable load 3-wire (NPN) Grommet 3-wire (PNP) 5 V, 12 V M9PV M9P V V V v v circuit M9V M9 V V V v v 2-wire 12 V Connector H7C V V V V 3-wire (NPN) M9NWV M9NW V V V v v IC 5 V, 12 V Yes 3-wire (PNP) 24 V M9PWV M9PW V V V v v circuit 2-wire 12 V M9WV M9W V V V v v 3-wire (NPN) M9NV 1 M9N 1 v v V v v IC 5 V, 12 V 3-wire (PNP) M9PV 1 M9P 1 v v V v v circuit 2-wire 12 V M9V 1 M9 1 v v V v v Diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V H7N V V v v IC circuit 3-wire (Equiv. to NPN) How to Order Pivot bracket Nil N Pivot bracket is shipped together with the product. Only for D, U, T mounting types Pivot bracket is shipped together with the product, but not assembled. No bracket is provided for the female rod end. Rod end bracket is shipped together with the product, but not assembled. knuckle joint pin is not provided with the single knuckle joint. Solid state auto switches marked with p are produced upon receipt of order. Since there are other applicable auto switches than listed above, refer to page 361 for details. or details about auto switches with pre-wired connector, refer to pages 1648 and The D-9ll/M9lll auto switches are shipped together, (but not assembled). (However, only the auto switch mounting brackets are assembled before shipment.) IC circuit 5 V 96V 96 V V Yes 100 V 93V 2 93 V V V V Grommet No 100 V or less 90V 90 V V IC circuit Yes 100 V, 200 V 54 V V V 12 V No 2-wire 24 V 200 V or less 64 V V Yes C73C V V V V Connector No 24 V or less C80C V V V V IC circuit Diagnostic indication (2-color indicator) Grommet Yes 59W V V None RoHS Refer to Ordering Example of Cylinder ssembly on page 326. Relay, PLC Relay, PLC 325 CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 D- -X Technical Data

42 K Series Specifications Symbol Rubber bumper ir cushion ction Lubricant luid ore size Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Double acting, Single rod Not required (Non-lube) ir 1.5 MPa 1.0 MPa 0.05 MPa Without auto switch: 10 C to 70 C (No freezing) With auto switch : 10 C to 60 C 50 to 500 mm/s Stroke length tolerance Up to 1000 st mm, Up to 1500 st mm Cushion Rubber bumper, ir cushion (ø40 to ø63 only) Rod non-rotating accuracy Note) ±1 ±0.8 ±0.5 asic, asic (without trunnion mounting female thread), Mounting xial foot, Rod flange, Head flange, Rod trunnion, Head trunnion, Clevis Note) The values are for standard strokes. ccessories/refer to page 309 for part numbers and dimensions. Symbol Made to Order Click here for details Specifications -Xl Change of rod end shape -XC8 djustable stroke cylinder/djustable extension type 1 -XC9 djustable stroke cylinder/djustable retraction type 1 -XC10 Dual stroke cylinder/double rod type -XC11 Dual stroke cylinder/single rod type 1 -XC12 Tandem cylinder 1, 2 -XC13 uto switch rail mounting 1 -XC20 Head cover axial port 1 -XC27 Double clevis and double knuckle joint pins made of stainless steel 1 Only compatible with cylinders with rubber bumper. 2 The shape is the same as the current product. Use the current seal kit. Refer to pages 355 to 361 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Cylinder mounting bracket, by stroke/ uto switch mounting surfaces Precautions Refer to page before handling. Standard Option Mounting asic xial foot Rod flange 1 double knuckle joint pin and retaining rings are shipped together. 2 Stainless steel mounting brackets and accessories are also available. Refer to page for details. uto switch Head flange Rod Head trunnion trunnion Clevis Rod end nut V V V V V V V Clevis pin V Single knuckle joint V V V V V V V Double knuckle joint 1 (With pin) V V V V V V V Pivot bracket V V V Standard Strokes ore size Standard stroke Note 1) Maximum manufacturable stroke Note 2) 20 25, 50, 75, 100, 125, 150, to , 63 25, 50, 75, 100, 125, 150, 200, 250, to 1500 Note 1) Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) The maximum manufacturable stroke shows the long stroke. Note 3) pplicable strokes should be confirmed according to the usage. or details, refer to ir Cylinders Model Selection on front matter pages. In addition, the products that exceed the standard stroke might not be able to fulfill the specifications due to the deflection etc. Ordering Example of Cylinder ssembly Cylinder model: CDG1KDN20-100Z-NW-M9W Clevis Mounting D: Clevis Pivot bracket N: Yes Rod end bracket W: Double knuckle joint uto switch D-M9W: 2 pcs. Pivot bracket Pivot bracket, double knuckle joint and auto switch are shipped together with the product, but not assembled. Double knuckle joint C 326

43 ir Cylinder: Non-rotating Rod Type Double cting K Series Weights asic weight ore size Calculation (Example) KLN20-100Z (oot, ø20, 100 stroke) Note) Order two foots per cylinder. asic xial foot lange Trunnion Clevis Pivot bracket Single knuckle joint Double knuckle joint (with pin) dditional weight per 50 mm of stroke dditional weight with air cushion dditional weight for long stroke Weight reduction for female rod end Mounting rackets/part No. (kg) Oasic weight 0.21 (oot, ø20) Odditional weight 0.05/50 stroke Oir cylinder stroke 100 stroke x 100/50 = 0.31 kg Mounting Order ore size bracket q ty Contents xial foot 2 Note) CG-L020 CG-L025 CG-L032 CG-L040 CG-L050 CG-L063 2 foots, 8 mounting bolts lange 1 CG-020 CG-025 CG-032 CG-040 CG-050 CG flange, 4 mounting bolts Trunnion pin 1 CG-T020 CG-T025 CG-T032 CG-T040 CG-T050 CG-T063 2 trunnion pins, 2 trunnion bolts, 2 flat washers Clevis 1 CG-D020 CG-D025 CG-D032 CG-D040 CG-D050 CG-D063 1 clevis, 4 mounting bolts, 1 clevis pin, 2 retaining rings Pivot bracket 1 CG CG CG CG CG CG pivot bracket CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 327 D- -X Technical Data

44 K Series Construction With rubber bumper o r!7 t!9 q w y!8 e i u!6!9!5 t Long stroke ø20 to ø32 With air o r!7 t q!9!2!4 w e!8 i!0!3!6!9!5 Long stroke Component Parts No. Description Material Note 1 Rod cover luminum alloy Hard anodized 2 Tube cover luminum alloy Hard anodized 3 Piston luminum alloy 4 Piston rod Stainless steel or ø20 or ø25 with built-in magnet Carbon steel Hard chrome plating 5 Non-rotating guide earing alloy 6 umper Resin 7 umper Resin ø32 or larger is common. 8 Wear ring Resin 9 Rod end nut Carbon steel Zinc chromated 10 Seal retainer Rolled steel Zinc chromated 11 Cushion valve ø40 or smaller Carbon steel Electroless nickel plating ø50 or larger Steel wire Zinc chromated 12 Cushion seal Urethane 13 Cushion seal Urethane ø32 or larger is common. 14 Cushion seal holder luminum alloy 15 Head cover luminum alloy Hard anodized 16 Cylinder tube luminum alloy Hard anodized 17 Rod seal NR 18 Piston seal NR 19 Tube gasket NR 20 Valve seal NR Note) or cylinders with auto switches, the magnet is installed in the piston. The material is stainless steel for ø20 to ø Replacement Parts: Seal Kit ore size Kit no. Contents 20 KN20Z-PS Set of the 25 KN25Z-PS nos. 32 KN32Z-PS!7,!8,!9 40 KN40Z-PS Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. Note) Refer to the Specific Product Precautions on page for Disassembly/Replacement. Order with the kit number according to the bore size. The seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-010 (10 g)

45 ir Cylinder: Non-rotating Rod Type Double cting K Series asic With rubber bumper ø20 to ø63 C C 10 C N With air cushion ø40 to ø63 Wθ C N emale rod end Width across flats K 8 x J MM øe Width across flats 1 MM øe H1 L H Width across flats K H1 ød ød R0.4 G T W G Width across L flats 1 T 4 x TC 8 x J H S + Stroke R0.4 MM thread depth 1 H 2 x RcP øi 4 x TC S + Stroke 2 x P Cushion valve, Width across flats WH øi G T T R0.4 øe W G ore Stroke range L 1 C size Standard Long stroke D E G G H H1 I J K MM N P S T T TC ZZ 20 Up to to (12) M4 x 0.7 depth 7 8 M8 x /8 69 (77) M5 x (114) 25 Up to to (12) M5 x 0.8 depth M10 x /8 69 (77) M6 x (119) 32 Up to to (12) M5 x 0.8 depth 8 10 M10 x /8 71 (79) (11) M8 x (121) 40 Up to to (13) M6 x 1 depth M14 x /8 78 (87) (12) M10 x (139) 50 Up to to (14) M8 x 1.25 depth M18 x /4 90 (102) (13) M12 x (162) 63 Up to to (14) M10 x 1.5 depth M18 x /4 90 (102) (13) M14 x (162) Note 1) Dimensions for each mounting bracket are the same as those for the standard or long stroke model. Refer to pages 301 to 307. Note 2) ( ): Denotes the dimensions for long stroke. R0.4 øe With ir Cushion ore size W W Wθ WH (17) (18) (18) 20 3 Note) ( ): Denotes the dimensions for long stroke. emale Rod End ore size 1 H MM ZZ M4 x (92) M5 x (93) M6 x 1 87 (95) M8 x (104) M10 x (120) M10 x (120) CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 329 D- -X Technical Data

46 ir Cylinder: Non-rotating Rod Type Double cting, Double Rod KW Series ø20, ø25, ø32, ø40, ø50, ø63 RoHS How to Order With auto switch 25 With auto switch (uilt-in magnet) KW CDG1KW Non-rotating rod type Double acting, Double rod type L L N N 25 Mounting asic Z asic (without trunnion mounting female thread) Type L xial foot N Rubber bumper lange U Trunnion ore size Mounting bracket is shipped together with the mm product, but not assembled. The cylinder for, L mounting types is Z: asic mm (without trunnion mounting female thread) mm mm mm mm 100 Z 100 Z M9W Cylinder stroke Refer to Standard Strokes on page 331. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. uto switch Nil Without auto switch or applicable auto switches, refer to the table below. uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDG1KWN32-100Z pplicable uto Switches/Refer to pages 1575 to 1701 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Electrical entry Grommet Diagnostic indication (2-color indicator) Water resistant (2-color indicator) Indicator light Load voltage uto switch model Lead wire length (m) Wiring pplicable bore size Pre-wired pplicable load (Output) None DC C ø20 to ø63 connector (Nil) (M) (L) (Z) (N) Perpendicular In-line 3-wire (NPN) M9NV M9N V V V v v IC 5 V, 12 V 3-wire (PNP) M9PV M9P V V V v v circuit M9V M9 V V V v v 2-wire 12 V Connector H7C V V V V 3-wire (NPN) M9NWV M9NW V V V v v IC 5 V, 12 V Yes 3-wire (PNP) 24 V M9PWV M9PW V V V v v circuit 2-wire 12 V M9WV M9W V V V v v Grommet 3-wire (NPN) M9NV 1 M9N 1 v v V v v IC 5 V, 12 V circuit 3-wire (PNP) M9PV 1 M9P 1 v v V v v 2-wire 12 V M9V 1 M9 1 v v V v v Diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V H7N V V v v IC circuit 3-wire (Equiv. to NPN) IC circuit 5 V 96V 96 V V Yes 100 V 93V 2 93 V V V V Grommet No 100 V or less 90V 90 V V IC circuit Yes 100 V, 200 V 54 V V V 12 V No 2-wire 24 V 200 V or less 64 V V Connector Yes C73C V V V V No 24 V or less C80C V V V V IC circuit Diagnostic indication (2-color indicator) Grommet Yes 59W V V 1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please consult with SMC regarding water resistant types with the above model numbers. 2 1 m type lead wire is only applicable to D-93. Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) H7CN Relay, PLC Relay, PLC Solid state auto switches marked with p are produced upon receipt of order. Since there are other applicable auto switches than listed above, refer to page 361 for details. or details about auto switches with pre-wired connector, refer to pages 1648 and The D-9ll/M9lll auto switches are shipped together, (but not assembled). (However, only the auto switch mounting brackets are assembled before shipment.) 330

47 ir Cylinder: Non-rotating Rod Type Double cting, Double Rod KW Series Specifications Symbol Rubber bumper Refer to pages 355 to 361 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Cylinder mounting bracket, by stroke/ uto switch mounting surfaces Precautions Refer to page before handling. ction Lubricant luid ore size Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Double acting, Double rod Not required (Non-lube) oot and flange types of cylinder sizes from ø20 to ø63 do not have trunnion mounting female thread. Operate the cylinder within the allowable kinetic energy. Refer to page 311 for details. Note) The values are for standard strokes. ir 1.5 MPa 1.0 MPa 0.08 MPa Without auto switch: 10 C to 70 C (No freezing) With auto switch : 10 C to 60 C 50 to 500 mm/s +1.8 Stroke length tolerance Up to 1000 st mm, Up to 1500 st 0 mm Cushion Rubber bumper Rod non-rotating accuracy Note) ±1 ±0.8 ±0.5 Mounting asic, asic (without trunnion mounting female thread), xial foot, lange, Trunnion ccessories/refer to page 309 for part numbers and dimensions. Mounting asic xial foot lange Trunnion Standard Rod end nut V V V V Single knuckle joint V V V V Option Double knuckle joint (with pin) 1 V V V V Pivot bracket V 1 double knuckle joint pin and retaining rings are shipped together. 2 Stainless steel mounting brackets and accessories are also available. Refer to page for details. CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Weights (kg) ore size asic xial foot lange Trunnion Pivot bracket Single knuckle joint Double knuckle joint (with pin) dditional weight per 50 mm of stroke Weight reduction for female rod end Calculation (Example) KWLN32-100Z Oasic weight 0.49 (oot, ø32) (oot, ø32, 100 stroke) Odditional weight 0.13/50 stroke Oir cylinder stroke 100 stroke x 100/50 = 0.75 kg asic weight Standard Strokes ore size Standard stroke Note 1) Maximum manufacturable stroke Note 2) 20 25, 50, 75, 100, 125, 150, to , 50, 75, 100, 125, 150, 200, , to , 63 Note 1) Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) The maximum manufacturable stroke shows the long stroke. Note 3) pplicable strokes should be confirmed according to the usage. or details, refer to ir Cylinders Model Selection on front matter pages. In addition, the products that exceed the standard stroke might not be able to fulfill the specifications due to the deflection etc. Mounting rackets/part No. Mounting bracket Order q ty Note) Order two foots per cylinder. ore size xial foot 2 Note) CG-L020 CG-L025 CG-L032 CG-L040 CG-L050 CG-L063 lange 1 CG-020 CG-025 CG-032 CG-040 CG-050 CG-063 Trunnion pin 1 CG-T020 CG-T025 CG-T032 CG-T040 CG-T050 CG-T063 Pivot bracket 1 CG CG CG CG CG CG pivot bracket Contents 2 foots, 8 mounting bolts 1 flange, 4 mounting bolts 2 trunnion pins, 2 trunnion bolts, 2 flat washers 331 D- -X Technical Data

48 KW Series Construction!0 t!1 u!4 q e o!3 r w i!2 y u ø20 to ø32 Component Parts No. Description Material Note 1 Rod cover luminum alloy Hard anodized 2 Rod cover luminum alloy Hard anodized 3 Cylinder tube luminum alloy Hard anodized 4 Piston luminum alloy 5 Piston rod 6 Piston rod Stainless steel Carbon steel * 7 Non-rotating guide earing alloy 8 ushing earing alloy 9 umper Resin ø32 or smaller Hard chrome plating * ø40 or larger Stainless steel or ø20 or ø25 with built-in magnet Carbon steel ** Hard chrome plating * 10 Rod end nut Carbon steel Zinc chromated 11 Rod seal NR 12 Rod seal NR 13 Piston seal NR 14 Tube gasket NR * The material is stainless steel for ø20 to ø32. ** The material for ø20, ø25 cylinders with auto switches is made of stainless steel. *** or cylinders with auto switches, the magnet is installed in the piston. Replacement Parts: Seal Kit ore size Kit no. Contents 20 KWN20Z-PS 25 KWN25Z-PS 32 KWN32Z-PS 40 KWN40Z-PS Set of the nos.!1,!2,!3,!4 Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. Note) Refer to the Specific Product Precautions on page for Disassembly/Replacement. Order with the kit number according to the bore size. * The seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-010 (10 g) 332

49 ir Cylinder: Non-rotating Rod Type Double cting, Double Rod KW Series asic with Rubber umper: KWN C C N Width across flats K øe MM Width across flats 1 8 x J H1 L H ødk R0.4 G T 2 x RcP 4 x TC øi S + Stroke ZZ + 2 Stroke G ød R0.4 Width across flats K H1 L T K H + Stroke MM Note 1) Dimensions are the same as those for the W standard. Refer to pages 316 and 317. øe Width across flats 1 ore size Stroke range L 1 C D DK E G H1 I J K K K MM N P S 20 Up to M4 x 0.7 depth M8 x / Up to M5 x 0.8 depth M10 x / Up to M5 x 0.8 depth M10 x / Up to M6 x 1 depth M14 x / Up to M8 x 1.25 depth M18 x / Up to M10 x 1.5 depth M18 x /4 102 ore size T TC H ZZ M5 x M6 x M8 x M10 x M12 x M14 x CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 333 D- -X Technical Data

50 ir Cylinder: Direct Mount Type Double cting R Series ø20, ø25, ø32, ø40, ø50, ø63 RoHS How to Order R N Z With auto switch CDG1R N Z M9W With auto switch (uilt-in magnet) N Type Rubber bumper ir cushion uilt-in Magnet Cylinder Model ore size mm mm mm mm mm mm Cylinder stroke Refer to Standard Strokes on page 335. If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDG1R32-100Z Rod end bracket Nil None V Single knuckle joint W Double knuckle joint * No bracket is provided for the female rod end. * Rod end bracket is shipped together with the product, but not assembled. * knuckle joint pin is not provided with the single knuckle joint. Rod end thread Nil Male rod end emale rod end Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. uto switch Nil Without auto switch * or applicable auto switches, refer to the table below. Made to Order or details, refer to page 335. * Refer to Ordering Example of Cylinder ssembly on page 335. pplicable uto Switches/Refer to pages 1575 to 1701 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indicator) Water resistant (2-color indicator) Electrical entry Grommet Indicator light Load voltage uto switch model Lead wire length (m) Wiring pplicable bore size Pre-wired pplicable load (Output) None DC C ø20 to ø63 connector (Nil) (M) (L) (Z) (N) Perpendicular In-line 3-wire (NPN) M9NV M9N V V V v v IC 5 V, 12 V 3-wire (PNP) M9PV M9P V V V v v circuit M9V M9 V V V v v 2-wire 12 V Connector H7C V V V V 3-wire (NPN) M9NWV M9NW V V V v v IC 5 V, 12 V Yes 3-wire (PNP) 24 V M9PWV M9PW V V V v v circuit 2-wire 12 V M9WV M9W V V V v v Grommet 3-wire (NPN) M9NV*1 M9N*1 v v V v v IC 5 V, 12 V circuit 3-wire (PNP) M9PV*1 M9P*1 v v V v v 2-wire 12 V M9V*1 M9*1 v v V v v Diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V H7N V V v v IC circuit 3-wire (Equiv. to NPN) IC circuit 5 V 96V 96 V V Yes 100 V 93V*2 93 V V V V Grommet No 100 V or less 90V 90 V V IC circuit Yes 100 V, 200 V 54 V V V 12 V No 2-wire 24 V 200 V or less 64 V V Connector Yes C73C V V V V No 24 V or less C80C V V V V IC circuit Diagnostic indication (2-color indicator) Grommet Yes 59W V V *1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please consult with SMC regarding water resistant types with the above model numbers. *2 1 m type lead wire is only applicable to D-93. * Lead wire length symbols: 0.5 m Nil (Example) M9NW * Solid state auto switches marked with p are produced upon receipt of order. 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) H7CN * Since there are other applicable auto switches than listed above, refer to page 361 for details. * or details about auto switches with pre-wired connector, refer to pages 1648 and * The D-9ll/M9lll auto switches are shipped together, (but not assembled). (However, only the auto switch mounting brackets are assembled before shipment.) 334 Relay, PLC Relay, PLC

51 ir Cylinder: Direct Mount Type Double cting R Series The R direct mount cylinder can be installed directly through the use of a square rod cover. Space-saving has been realized. ecause it is a directly mounted type without using brackets, its overall length is shorter, and its installation pitch can be made smaller. Thus, the space that is required for installation has been dramatically reduced. Specifications ction Lubricant luid ore size Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Double acting, Single rod Not required (Non-lube) ir 1.5 MPa 1.0 MPa 0.05 MPa Without auto switch: 10 C to 70 C (No freezing) With auto switch : 10 C to 60 C 50 to 1000 mm/s Stroke length tolerance Up to 300 st mm Cushion Rubber bumper, ir cushion CJ1 CJP CJ2 JCM CM2 CM3 Symbol Rubber bumper ir cushion Standard Strokes ore size Standard stroke 20 25, 50, 75, 100, 125, , 32 25, 50, 75, 100, 125, 150, , 50, 63 25, 50, 75, 100, 125, 150, 200, 250, 300 JM M Symbol Made to Order Click here for details Specifications -Xl Change of rod end shape -X6 Heat resistant cylinder ( 10 to 150 C) 2 -X7 Cold resistant cylinder ( 40 to 70 C) 1, 3 -X9 Low speed cylinder (10 to 50 mm/s) 1, 3 -X13 Low speed cylinder (5 to 50 mm/s) 1, 3 -XC6 Made of stainless steel -XC8 djustable stroke cylinder/djustable extension type 1 -XC9 djustable stroke cylinder/djustable retraction type 1 -XC13 uto switch rail mounting 1 -XC20 Head cover axial port 1 -XC22 luororubber seal -XC85 Grease for food processing equipment 1 Only compatible with cylinders with rubber bumper. 2 Cylinders with rubber bumper have no bumper. 3 The shape is the same as the current product. Use the current seal kit. Refer to pages 355 to 361 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Cylinder mounting bracket, by stroke/ uto switch mounting surfaces Precautions Refer to page before handling. Please consult with SMC for strokes which exceed the standard stroke length. Note 1) Intermediate strokes not listed above are produced upon receipt of order. Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) pplicable strokes should be confirmed according to the usage. or details, refer to ir Cylinders Model Selection on front matter pages. In addition, the products that exceed the standard stroke might not be able to fulfill the specifications due to the deflection etc. Tightening Torque: Tighten the cylinder mounting bolts with the following tightening torque. ore size Hexagon socket head cap screw size Tightening torque (N m) 20 M5 x to M6 4.2 to M to M to M to M to Ordering Example of Cylinder ssembly Cylinder model: CDG1RN20-100Z-W-M9W Rod end bracket W: Double knuckle joint uto switch D-M9W: 2 pcs. Double knuckle joint and auto switch are shipped together with the product, but not assembled. Double knuckle joint uto switch 335 M1 C2 CS1 CS2 D- -X Technical Data

52 R Series Weights (kg) ore size asic weight Single knuckle joint Double knuckle joint (with pin) dditional weight per 50 mm of stroke dditional weight with air cushion Weight reduction for female rod end Calculation (Example) RN32-100Z (ø32, 100 stroke) Oasic weight 0.35 Odditional weight 0.09/50 stroke Oir cylinder stroke 100 stroke x 100/50 = 0.53 kg ccessories Mounting asic Standard Rod end nut V Option Single knuckle joint Double knuckle joint 1 (with pin) 1 double knuckle joint pin and retaining rings are shipped together. 2 Refer to page 309 for part numbers and dimensions of the accessories. 3 Stainless steel accessories are also available. Refer to page for details. V V 336

53 ir Cylinder: Direct Mount Type Double cting R Series Construction With rubber bumper o r!6t!8 qy w e!7 iu With air cushion!9!3 o r!6 t q!8!4 w!0 e!7 i!2!5!1 CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Component Parts No. Description Material Note 1 Rod cover luminum alloy Hard anodized 2 Tube cover luminum alloy Hard anodized 3 Piston luminum alloy 4 Piston rod 5 ushing earing alloy Stainless steel or ø20 or ø25 with built-in magnet Carbon steel * Hard chrome plating * 6 umper Resin ø32 or larger is 7 umper Resin common. 8 Wear ring Resin 9 Rod end nut Carbon steel Zinc chromated No. Description Material Note 11 Cushion ring luminum alloy 12 Seal retainer Rolled steel Zinc chromated 13 Cushion ø40 or smaller Carbon steel Electroless nickel plating valve ø50 or larger Steel wire Zinc chromated 14 Cushion seal Urethane ø32 or larger is 15 Cushion seal Urethane common. 16 Rod seal NR 17 Piston seal NR 18 Tube gasket NR 19 Valve seal NR 10 Cushion ring luminum alloy Note) or cylinders with auto switches, the magnet is installed in the piston. * The material for ø20, ø25 cylinders with auto switches is made of stainless steel. Replacement parts/seal kit are the same as standard type, double acting, single rod. Refer to page 298. Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. Note) Refer to the Specific Product Precautions on page for Disassembly/Replacement. 337 D- -X Technical Data

54 R Series asic with ottom Mounting With rubber bumper L 2 x øld Width across flats K MM H1 X ød G 2 x RcP øi G R0.4 øe LH LX L Width across flats 1 L K H Y N S + Stroke With air cushion L LH 2 x øld LX L WC Width across flats K MM Width across flats 1 H1 X L K H ød Y W G N 2 x RcP Cushion valve, W Width across flats WH øi S + Stroke G R0.4 øe Wθ 10 Port location WD emale rod end MM Effective depth 1 X ø20, ø25 H ore size Stroke range L 1 D E G G H H1 I K K L LD LH LX MM N P S X Y ZZ 20 Up to ø5.5, ø9.5 depth of counterbore M8 x / Up to ø6.6, ø11 depth of counterbore M10 x / Up to ø9, ø14 depth of counterbore M10 x / Up to ø11, ø17.5 depth of counterbore M14 x / Up to ø14, ø20 depth of counterbore M18 x / Up to ø18, ø26 depth of counterbore M18 x / With ir Cushion ore size Stroke range P W W WC WD Wθ WH 20 Up to 150 M5 x Up to 200 M5 x Up to 200 Rc1/ Up to 300 Rc1/ Up to 300 Rc1/ Up to 300 Rc1/ emale Rod End ore size 1 H MM X ZZ M4 x M5 x M6 x M8 x M10 x M10 x

55 With auto switch With auto switch (uilt-in magnet) KRN CDG1KRN Z M9W Non-rotating rod type If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDG1KRN32-100Z N Mounting Rubber bumper Note) ir cushion type KR is a Made-to-Order product. uilt-in Magnet Cylinder Model ore size mm mm mm mm mm mm Z Rod end thread Nil Male rod end emale rod end Rod end bracket Nil None V Single knuckle joint W Double knuckle joint * No bracket is provided for the female rod end. * Rod end bracket is shipped together with the product, but not assembled. * knuckle joint pin is not provided with the single knuckle joint. Cylinder stroke Refer to Standard Strokes on page 340. pplicable uto Switches/Refer to pages 1575 to 1701 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indicator) Water resistant (2-color indicator) Electrical entry Grommet Indicator light Wiring (Output) Load voltage uto switch model Lead wire length (m) pplicable bore size DC C None (Nil) (M) (L) (Z) (N) Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. uto switch Nil Without auto switch * or applicable auto switches, refer to the table below. Made to Order Refer to page 340 for details. Pre-wired connector ø20 to ø63 Perpendicular In-line M9NV M9N V V V v v IC Diagnostic indication (2-color indicator) Grommet Yes 59W V V *1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please consult with SMC regarding water resistant types with the above model numbers. *2 1 m type lead wire is only applicable to D-93. * Lead wire length symbols: 0.5 m Nil (Example) M9NW * Solid state auto switches marked with p are produced upon receipt of order. 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) H7CN * Since there are other applicable auto switches than listed above, refer to page 361 for details. * or details about auto switches with pre-wired connector, refer to pages 1648 and * The D-9ll/M9lll auto switches are shipped together, (but not assembled). (However, only auto switch mounting brackets are assembled before shipment.) pplicable load 3-wire (NPN) Grommet 3-wire (PNP) 5 V, 12 V M9PV M9P V V V v v circuit M9V M9 V V V v v 2-wire 12 V Connector H7C V V V V 3-wire (NPN) M9NWV M9NW V V V v v IC 5 V, 12 V Yes 3-wire (PNP) 24 V M9PWV M9PW V V V v v circuit 2-wire 12 V M9WV M9W V V V v v 3-wire (NPN) M9NV*1 M9N*1 v v V v v IC 5 V, 12 V 3-wire (PNP) M9PV*1 M9P*1 v v V v v circuit 2-wire 12 V M9V*1 M9*1 v v V v v Diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V H7N V V v v IC circuit 3-wire IC Yes (Equiv. to NPN) 5 V 96V 96 V V circuit 100 V 93V*2 93 V V V V Grommet No 100 V or less 90V 90 V V IC circuit Yes 100 V, 200 V 54 V V V 12 V No 2-wire 24 V 200 V or less 64 V V Connector ir Cylinder: Direct Mount, Non-rotating Rod Type KR Series ø20, ø25, ø32, ø40, ø50, ø63 How to Order RoHS Yes C73C V V V V No 24 V or less C80C V V V V IC circuit Relay, PLC Relay, PLC 339 CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 D- -X Technical Data

56 KR Series KR series direct mount, non-rotating rod type cylinder can be installed directly through the use of a square rod cover. Space-saving has been realized. ecause it is a directly mounted type without using brackets, its overall length is shorter, and its installation pitch can be made smaller. Thus, the space that is required for installation has been dramatically reduced. Specifications ore size ction Double acting, Single rod Lubricant luid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Not required (Non-lube) ir 1.5 MPa 1.0 MPa 0.05 MPa Without auto switch: 10 C to 70 C (No freezing) With auto switch : 10 C to 60 C 50 to 500 mm/s Stroke length tolerance Up to 300 st mm Cushion Rubber bumper Rod non-rotating accuracy ±1 ±0.8 ±0.5 Weights C Symbol Rubber bumper Made to Order Click here for details Symbol Specifications -XC8 djustable stroke cylinder/djustable extension type *1 -XC9 djustable stroke cylinder/djustable retraction type *1 -XC20 Head cover axial port *1 The shape is the same as the current product. Use the current seal kit. ccessories Mounting asic Standard Rod end nut V Option Single knuckle joint Double knuckle joint *1 (with pin) *1 double knuckle joint pin and retaining rings are shipped together. *2 Refer to page 309 for part numbers and dimensions of the accessories. *3 Stainless steel accessories are also available. Refer to page for details. Refer to pages 355 to 361 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Cylinder mounting bracket, by stroke/ uto switch mounting surfaces Refer to page before handling. 340 Precautions V V (kg) ore size asic weight Single knuckle joint Double knuckle joint (with pin) dditional weight per 50 mm of stroke Weight reduction for female rod end Calculation (Example) KRN32-100Z (ø32, 100 stroke) Standard Strokes ore size Standard stroke * 20 25, 50, 75, 100, 125, , 32 25, 50, 75, 100, 125, 150, , 50, 63 25, 50, 75, 100, 125, 150, 200, 250, 300 * Please consult with SMC for strokes which exceed the standard stroke length. Note 1) Intermediate strokes not listed above are produced upon receipt of order. Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) pplicable strokes should be confirmed according to the usage. or details, refer to ir Cylinders Model Selection on front matter pages. In addition, the products that exceed the standard stroke might not be able to fulfill the specifications due to the deflection etc. Ordering Example of Cylinder ssembly Cylinder model: CDG1KRN20-100Z-W-M9W Oasic weight 0.35 Odditional weight 0.09/50 stroke Oir cylinder stroke 100 stroke x 100/50 = 0.53 kg Double knuckle joint Tightening Torque: Tighten the cylinder mounting bolts with the following tightening torque. ore size Hexagon socket head cap screw size Tightening torque (N m) 20 M5 x to M6 4.2 to M to M to M to M to Rod end bracket W: Double knuckle joint uto switch D-M9W: 2 pcs. * Double knuckle joint and auto switch are shipped together with the product, but not assembled. uto switch

57 ir Cylinder: Direct Mount, Non-rotating Rod Type KR Series Construction Non-rotating rod type/ ottom mounting type!0 r!1 t!3 q w u!2 e o i y t CJ1 CJP CJ2 JCM CM2 CM3 ø20 to ø32 JM Component Parts No. Description Material Note 1 Rod cover luminum alloy Clear hard anodized 2 Tube cover luminum alloy Clear hard anodized 3 Piston luminum alloy 4 Piston rod ø20 to ø32 Stainless steel ø40 to ø63 Carbon steel Hard chrome plating 5 Non-rotating guide Oil-impregnated sintered alloy 6 ushing Oil-impregnated sintered alloy ø20 to ø32 only 7 umper Resin 8 umper Resin 9 Wear ring Resin 10 Rod end nut Rolled steel Zinc chromated 11 Rod seal NR 12 Piston seal NR 13 Tube gasket NR Replacement parts/seal kit are the same as double acting, non-rotating rod type. Refer to page 328. Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. Note) Refer to the Specific Product Precautions on page for Disassembly/Replacement. M M1 C2 CS1 CS2 D- -X 341 Technical Data

58 KR Series asic with ottom Mounting: KRN With rubber bumper 2 x øld Width across flats K MM H1 X G 2 x RcP G R0.4 LH L øi 0 øe 0.05 ød LX L Width across flats 1 L H Y N S + Stroke emale rod end MM Effective depth 1 X H emale Rod End ore size 1 H MM X ZZ M4 x M5 x M6 x M8 x M10 x M10 x ore size Stroke range L 1 D E G G H H1 I K L LD LH LX MM N P S X Y ZZ 20 Up to ø5.5, ø9.5 depth of counterbore M8 x / Up to ø6.6, ø11 depth of counterbore M10 x / Up to ø9, ø14 depth of counterbore M10 x / Up to ø11, ø17.5 depth of counterbore M14 x / Up to ø14, ø20 depth of counterbore M18 x / Up to ø18, ø26 depth of counterbore M18 x / uto switch mounting position is the same as that on page

59 ir Cylinder: With End Lock Series ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 pplicable uto Switches/Refer to pages 1575 to 1701 for further information on auto switches. Load voltage uto switch model Lead wire length (m) Electrical Wiring pplicable bore size Pre-wired Type Special function entry (Output) None pplicable load DC C ø20 to ø63 ø80, ø100 connector (Nil) (M) (L) (Z) (N) Perpendicular In-line In-line 3-wire M9NV M9N V V V v v (NPN) G59 V V v v IC 5 V, 12 V 3-wire M9PV M9P V V V v v circuit Grommet (PNP) G5P V V v v M9V M9 V V V v v 2-wire 12 V K59 V V v v Connector H7C V V V V 3-wire M9NWV M9NW V V V v v (NPN) G59W V V v v IC Relay, Yes 24 V 5 V, 12 V Diagnostic indication 3-wire M9PWV M9PW V V V v v circuit PLC (2-color indicator) (PNP) G5PW V V v v M9WV M9W V V V v v 2-wire 12 V Grommet K59W V V v v 3-wire (NPN) M9NV*1 M9N*1 v v V v v 5 V, 12 V Water resistant 3-wire (PNP) M9PV*1 M9P*1 v v V v v IC circuit (2-color indicator) M9V*1 M9*1 v v V v v 2-wire 12 V G5*1 V v v Diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V H7N V V v v IC circuit 3-wire (Equiv. to NPN) 5 V 96V 96 V V IC circuit Yes 100 V 93V*2 93 V V V V Grommet No 100 V or less 90V 90 V V IC circuit Yes 2-wire 24 V 12 V 100 V, 200 V 54 V V V Relay, No 200 V or less 64 V V PLC Yes C73C V V V V Connector No 24 V or less C80C V V V V IC circuit Diagnostic indication (2-color indicator) Grommet Yes 59W V V *1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please consult with SMC regarding water resistant types with the above model numbers. *2 1 m type lead wire is only applicable to D-93. Solid state auto switch Reed auto switch L N CDG1 * Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL Indicator light L With auto switch (uilt-in magnet) Mounting asic N L xial foot Rod flange G Head flange U* Rod trunnion T* Head trunnion D Clevis * Not available for bore size ø80 and ø100. esides, trunnion cannot be attached in the side to which an end lock is attached. Note) Mounting brackets are shipped together, (but not assembled). N 25 Type Rubber bumper ir cushion ore size mm mm mm mm mm mm mm mm Cylinder stroke Refer to Standard Strokes on page 344. uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDG RL How to Order 100 H N M9W 5 m Z (Example) M9NWZ None N (Example) H7CN * Solid state auto switches marked with p are produced upon receipt of order. * Since there are other applicable auto switches than listed above, refer to page 361 for details. * or details about auto switches with pre-wired connector, refer to pages 1648 and * The D-9ll/M9lll auto switches are shipped together, (but not assembled). (However, only auto switch mounting brackets are assembled before shipment.) H N Manual release N Non-locking type L Locking type Lock position H Head end lock R Rod end lock W Double end lock With rod boot Nil Without rod boot J Nylon tarpaulin K Heat resistant tarpaulin * In the case of w/rod boot, and a foot bracket or rod side flange as a bracket, those parts are to be assembled at the time of shipment. C Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. uto switch Nil Without auto switch * or applicable auto switches, refer to the table below. uto switch mounting bracket Note) Note) This symbol is indicated when the D-9l or M9l type auto switch is specified.this mounting bracket does not apply to other auto switches (D-C7l and H7l, etc.) (Nil) Made to Order Refer to page 344 for details. 343 CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 D- -X Technical Data

60 Series Specifications Symbol Rubber bumper ir cushion ore size ction Lubricant luid Proof pressure Double acting, Single rod Not required (Non-lube) * 0.05 MPa except locking parts. ** Rod/Head trunnion types are not available for ø80 and ø100. Trunnion is not attached for a cover on which lock mechanism is equipped. ir 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.15 MPa * mbient and fluid temperature Without auto switch: 10 to 70 C (No freezing) With auto switch: 10 to 60 C (No freezing) Piston speed 50 to 1000 mm/s 50 to 700 mm/s st Up to 1000 mm st st Stroke length tolerance Up to mm, Up to mm st Up to mm Cushion Rubber bumper, ir cushion Mounting ** asic, xial foot, Rod flange, Head flange, Rod trunnion, Head trunnion, Clevis Lock Specifications C Symbol -Xl -XC13 Made to Order Click here for details Specifications Change of rod end shape uto switch rail mounting Refer to pages 355 to 361 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Cylinder mounting bracket, by stroke/ uto switch mounting surfaces Refer to page before handling. 344 Precautions Lock position Head end, Rod end, Double end Holding force ø20 ø25 ø32 ø40 ø50 ø63 ø80 ø100 (Max.) (N) acklash 2 mm or less Manual release Non-locking type, Locking type djust the switch position so that it operates upon movement to both the stroke end and backlash (2 mm) positions. Standard Strokes ore size Note 1) Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) Long stroke applies to the axial foot and rod flange types. If other mounting brackets are used, or the length exceeds the long stroke limit, refer to ir Cylinders Model Selection on front matter pages. Symbol Rod boot material Maximum operating temperature J Nylon tarpaulin 70 C K Heat resistant tarpaulin 110 C * Standard stroke Note 1) Long * Maximum ambient temperature for the rod boot itself. stroke 20 25, 50, 75, 100, 125, 150, to to to , 50, 75, 100, 125, 301 to , , 200, 250, to to to 1500 Rod oot Material ccessories Mounting Standard Rod end nut Option Single knuckle joint Double knuckle joint *1 (with pin) Pivot bracket Maximum manufacturable stroke 1500 asic *1 double knuckle joint pin and retaining rings are shipped together. *2 Refer to page 309 for part numbers and dimensions of the accessories. *3 Stainless steel mounting brackets and accessories are also available. Refer to page for details.

61 ir Cylinder: With End Lock Series Construction: With Rubber umper Head end lock Non-locking type manual release: Suffix N ø80, ø100 ø80, q @0 K!4!0!1 i o w!2 Rod end lock Locking type manual release: Suffix L!7!6!5!8 K w Long stroke CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Component Parts No. Description Material Note 1 Rod cover luminum alloy Hard anodized 2 Head cover luminum alloy Hard anodized 3 Tube cover luminum alloy Hard anodized 4 Cylinder tube luminum alloy Hard anodized 5 Piston luminum alloy Chromated 6 Piston rod Carbon steel * Hard chrome plating * 7 ushing earing alloy 8 Lock piston Carbon steel Hard chrome plating, Heat treated 9 Lock bushing Copper alloy 10 Lock spring Stainless steel 11 umper Resin 12 Hexagon socket head cap screw lloy steel lack zinc chromated 13 Cap luminum die-casted lack painted 13 Cap Carbon steel Oxide film treated 14 Rubber cap Synthetic rubber Note) or cylinders with auto switches, the magnet is installed in the piston. * The material for ø20, ø25 cylinders with auto switches is made of stainless steel. Replacement Parts: Seal Kit (With one end lock) Series ore size Kit no. Contents 20 N20-PS ln Set of the nos. 25 N25-PS type 32 N32-PS and grease pack 40 N40-PS Order seal kit in accordance with the bore size. Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. * The seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-010 (10 g) No. Description Material Note 15 M/O knob Zinc die-casted lack painted 16 M/O bolt lloy steel lack zinc chromated, Red painted 17 M/O spring Steel wire Zinc chromated 18 Stopper ring Carbon steel Zinc chromated 19 umper Resin 20 umper Resin ø40 or larger: Same as bumper 21 Retaining ring Stainless steel Not available for ø80, ø Piston gasket NR 23 Wear ring Resin 24 Rod end nut Carbon steel Zinc chromated 25 Rod seal NR 26 Piston seal NR 27 Cylinder tube gasket NR 1 pc. when using tube cover 28 Lock piston seal NR 2 pcs. for double end lock 29 Piston holder Resin ø40 to ø100, head end lock only Replacement Parts: Seal Kit (With double end lock) Series ore size Kit no. Contents 20 N20-PS-W ln Set of the nos. 25 N25-PS-W type 32 N32-PS-W and grease pack 40 N40-PS-W Order seal kit in accordance with the bore size. Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. * The seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-010 (10 g) 345 D- -X Technical Data

62 Series Construction: With ir Cushion With air cushion Head end lock!2 Non-locking type manual release: Suffix q #6 r @6 #7 #1 K!4!0!1 i o w $0 #4 #3 #5 $1 Rod end lock e #2 w Long stroke Component Parts No. Description Material Note 1 Rod cover luminum alloy Hard anodized 2 Head cover luminum alloy Hard anodized 3 Tube cover luminum alloy Hard anodized 4 Cylinder tube luminum alloy Hard anodized 5 Piston luminum alloy Chromated 6 Piston rod Carbon steel * Hard chrome plating * 7 ushing earing alloy 8 Lock piston Carbon steel Hard chrome plating, Heat treated 9 Lock bushing Copper alloy 10 Lock spring Stainless steel 11 umper Resin 12 Hexagon socket head cap screw lloy steel lack zinc chromated 13 Cap luminum die-casted lack painted 13 Cap Carbon steel Oxide film treated 14 Rubber cap Synthetic rubber 15 M/O knob Zinc die-casted lack painted 16 M/O bolt lloy steel lack zinc chromated, Red painted 17 M/O spring Steel wire Zinc chromated 18 Stopper ring Carbon steel Zinc chromated Note) or cylinders with auto switches, the magnet is installed in the piston. * The material for ø20, ø25 cylinders with auto switches is made of stainless steel. Replacement Parts: Seal Kit (With one end lock) Series ore size Kit no. Contents PS Set of the nos. l ir cushion type PS $0, $ PS and grease pack Order seal kit in accordance with the bore size. Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. * The seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-010 (10 g) 346 No. Description Material Note 22 Piston gasket NR 23 Wear ring Resin 24 Rod end nut Carbon steel Zinc chromated 25 Rod seal NR 26 Piston seal NR 27 Cylinder tube gasket NR 1 pc. when using tube cover 28 Lock piston seal NR 2 pcs. for double end lock 29 Piston holder Resin ø40 to ø100 only 30 Cushion ring luminum alloy nodized 31 Cushion ring luminum alloy nodized 32 Seal retainer Rolled steel Only when using nickel plating, tube cover 33 Cushion valve Rolled steel Electroless nickel plating 34 Valve retainer Rolled steel Electroless nickel plating 35 Lock nut Rolled steel Nickel plating 36 Cushion seal Urethane 37 Cushion seal Urethane ø32 or larger: Same as 38 Cushion ring gasket NR 39 Cushion ring gasket NR ø32 or larger: Same as 40 Valve seal NR 41 Valve retaining gasket NR Replacement Parts: Seal Kit (With double end lock) Series ore size Kit no. Contents PS-W Set of the nos. l ir cushion type PS-W $0, $ PS-W and grease pack Order seal kit in accordance with the bore size. Note) s sizes ø50 and larger cannot be disassembled, the seal cannot be replaced. * The seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-010 (10 g)

63 ir Cylinder: With End Lock Series asic with Rubber umper: N Head end lock: N ore size Stroke Hl Width across flats 1 0 øe 0.05 MM H L C ±0.1 WL ør K H ød HR G T K C ±0.1 N 2 x RcP 2 x TC Non-locking type manual release: Suffix N 8 x J øi S + Stroke WL ømo HN G DL2 0 øe 0.05 Locking type manual release: Suffix L N TG 2 x TC øtd TE T T cross section CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 ore size Stroke range L 1 C D DL2 E G G H H1 HR HN (Max.) 20 Up to M4 x 0.7 depth 7 25 Up to M5 x 0.8 depth Up to M5 x 0.8 depth 8 40 Up to M6 x 1 depth Up to M8 x 1.25 depth Up to M10 x 1.5 depth Up to M10 x 1.5 depth Up to M12 x 1.75 depth 22 I J ore size K K MM MO N P R S T TC TD TE T TG WL ZZ M8 x / M5 x M10 x / M6 x M10 x / M8 x M14 x / M10 x M18 x / M12 x M18 x / M14 x M22 x / M26 x / D- -X Technical Data

64 Series asic with Rubber umper: N Rod end lock: N ore size Stroke Rl DL1 S + Stroke G T ( ): Denotes the dimensions for long stroke. ore size DL1 G S T ZZ (12) 80 (88) (125) (12) 80 (88) (130) (12) 81 (89) 10 (11) 123 (131) (13) 87 (96) 10 (12) 139 (148) (14) 102 (114) 12 (13) 162 (174) (14) 102 (114) 12 (13) 162 (174) (20) 124 (138) 198 (212) (20) 124 (138) 198 (212) Double end lock: N ore size Stroke Wl S + Stroke ore size S ZZ With rod boot 8 l 8 8 l øij øe l JH øij øe JW f h + l ZZ + l + Stroke ø20 to ø63 f h + l ZZ + l + Stroke ø80, ø100 ore size e f h IJ JH JW (Reference) (Reference) Head end lock: -Hl Rod end lock: -Rl Double end lock: -Wl l ZZ ZZ ZZ (145) (152) (153) (168) (194) (194) (221) (221) 229 ( ): Denotes the dimensions for long strokes. The minimum stroke with rod boot is 20 mm. 1 /4 stroke 348

65 ir Cylinder: With End Lock Series asic with ir Cushion: Head end lock: ore size Stroke Hl Rod end lock: ore size Stroke Rl 10 Wθ W 2 x P W CJ1 CJP CJ2 Max.WH JCM CM2 Head End Lock: -Hl or dimensions other than listed above, refer to the dimensions with rubber bumper. ore size P W W WH Wq 20 M5 x M5 x Rc1/ Rc1/ Rc1/ Rc1/ Rc3/ Rc1/ Rod End Lock: -Rl ore size P W W WH Wq 20 M5 x (16) M5 x (16) Rc1/ (16) Rc1/ (16) Rc1/ (18) Rc1/ (18) Rc3/ Rc1/ ( ): Denotes the dimensions for long strokes. or dimensions other than the listed above, refer to the dimensions with rubber bumper. CM3 JM M M1 C2 CS1 CS2 349 D- -X Technical Data

66 Series With Mounting racket (or dimensions other than listed below, refer to pages 347 to 349, 301 to 303.) xial foot: Ll LS + Stroke Head end lock: -Hl Rod end lock: -Rl Double end lock: -Wl ore size LS ZZ LS ZZ LS ZZ Without rod boot With rod boot Without rod boot With rod boot Without rod boot With rod boot l 56 (64) 121 (129) 141 (149) + l l l 56 (64) (134.5) (156.5) + l l l 55 (63) (135.5) (157.5) + l l l 60 (69) 144 (153) 164 (173) + l l l 67 (79) (181.5) (201.5) + l l l 67 (79) (181.5) (201.5) + l l l 76 (90) (218.5) (227.5) + l l l 76 (90) 208 (222) 217 (231) + l l ( ): Denotes the dimensions for long stroke. Rod flange: l Head flange: Gl Head end lock: -Hl Rod end lock: -Rl Double end lock: -Wl ore size ZZ (Head flange) Without rod boot With rod boot Without rod boot With rod boot Without rod boot With rod boot l l l l l l l l l l 147 (156) 167 (176) + l l l 171 (183) 191 (203) + l l l 171 (183) 191 (203) + l l l 209 (223) 218 (232) + l l l 212 (226) 221 (235) + l l ( ): Denotes the dimensions for long stroke. 350

67 ir Cylinder: With End Lock Series With Mounting racket Rod trunnion: Ul (Head end lock -Hl only) Head trunnion: Tl (Rod end lock -Rl only) Clevis: Dl ø20 to ø63 Clevis: Dl ø80, ø100 Z + Stroke Z + Stroke Rod end lock: -Rl ore size Z (Head trunnion) ZZ (Head trunnion) Without rod boot With rod boot Without rod boot With rod boot l l l l l l (134) 147 (154) + l 139 (148) 159 (168) + l (159) 168 (179) + l 162 (174) 182 (194) + l (159) 168 (179) + l 162 (174) 182 (194) + l ( ): Denotes the dimensions for long stroke. CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Z + Stroke Head end lock: -Hl Rod end lock: -Rl ore size Z ZZ Z ZZ Without rod boot With rod boot Without rod boot With rod boot Without rod boot With rod boot Without rod boot With rod boot l l l l l l l l l l l l l l 159 (168) 179 (188) + l 177 (186) 197 (206) + l l l 185 (197) 205 (217) + l 205 (217) 225 (237) + l l l 190 (202) 210 (222) + l 212 (224) 232 (244) + l l l 230 (244) 239 (253) + l 248 (262) 257 (277) + l l l 238 (252) 247 (261) + l 260 (274) 269 (283) + l Double end lock: -Wl ore size Z ZZ Without rod boot With rod boot Without rod boot With rod boot l l l l l l l l l l l l l l l l ( ): Denotes the dimensions for long stroke. 351 D- -X Technical Data

68 ir Cylinder: Low riction Type Double cting, Single Rod lq Series ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 How to Order Use the new series Smooth Cylinder Y series to realize both-direction low friction and low-speed operation. (Refer to the est Pneumatics No. 2-3.) With auto switch With auto switch (uilt-in magnet) L Q CDG1 L Q M9W C Mounting asic L xial foot Rod flange G Head flange U* Rod trunnion T* Head trunnion D Clevis * Not available for ø80 and ø100. Note) Mounting brackets are shipped together, (but not assembled). Low friction type Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. uto switch Nil Without auto switch Direction of low friction With pressure at head side With pressure at rod side uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDG1Q ore size mm mm mm mm mm mm mm mm Cylinder stroke uto switch mounting bracket Note) Note) This symbol is indicated when the D-9l or M9l type auto switch is specified.this mounting bracket does not apply to other auto switches (D-C7l and H7l, etc.) (Nil) Made to Order 354

69 Series uto Switch Mounting uto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height Solid state auto switch D-M9 /M9 W, D-M9 ø20 to ø63 Hs Hs Hs 16 D-M9 V/M9 WV, D-M9 V ø20 to ø63 16 D-G5/K5/G5 W/G5 D-K59W, D-G59, D-G5NT ø20 to ø (24) ( ): Dimension of the D-M9 and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. 20 (22) ( ): Dimension of the D-M9 V and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. Reed auto switch D-9 ø20 to ø63 Hs D-9 V ø20 to ø63 Hs Hs D-C7/C8, D-C73C/C80C ø20 to ø (22) ( ): Dimension of the D-96 and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. 22 and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 D-H7 /H7 W D-H7N/H7/D-H7C ø20 to ø63 Hs D-5/6/59W ø20 to ø100 Hs uto Switch Mounting Height uto switch model D-M9 (V) D-M9 W(V) D-M9 (V) D-9 (V) D-H7 D-H7 W D-H7N D-H7 D-C7/C8 D-C73C D-C80C D-G5/K5 D-G5 W D-K59W D-5/6 D-59W ore size Hs Hs Hs D-G5NT D-G59 D-H7C D-G5 355 D- -X Technical Data

70 Series uto Switch Proper Mounting Position (Detection at Stroke End) Except Single cting, Direct Mount Type (R, KR) and With End Lock () ore size uto switch model D-M9l D-M9lV D-M9lW D-M9lWV D-M9l D-M9lV D-9l D-9lV D-H7lW D-H7N D-H7 D-H7l D-H7C D-C7l D-C80 D-C73C D-C80C D-G5l/K59 D-G5lW/K59W D-G59 D-G5NT D-G5 D-5l D-64 D-59W 24 (32) 24.5 (32.5) 25 (33) 27 (36) 32 (44) 33.5 (45.5) (28) 20.5 (28.5) 21 (29) 23 (32) 28 (40) 29.5 (41.5) (27.5) 20 (28) 20.5 (28.5) 22.5 (31.5) 27.5 (39.5) 29 (41) (28.5) 21 (29) 21.5 (29.5) 23.5 (32.5) 28.5 (40.5) 30 (42) Note 1) The values in ( ) are for long stroke. Note 2) djust the auto switch after confirming the operating condition in the actual setting (24) 16.5 (24.5) 17 (25) 19 (28) 24 (36) 25.5 (37.5) 30.5 (44.5) 31.5 (45.5) (22.5) 15 (23) 15.5 (23.5) 17.5 (26.5) 22.5 (34.5) 24 (36) 29 (43) 30 (44) (25.5) 18 (26) 18.5 (26.5) 20.5 (29.5) 25.5 (37.5) 27 (39) 32 (46) 33 (47) Single cting, Spring Return Type (S) uto switch model ore size dimensions Up to 50 st 51 to 100 st 101 to 125 st 126 to 200 st D-M9l(V) D-M9lW(V) D-M9l(V) D-9l(V) D-H7l D-H7lW D-H7C D-H D-H7N D-C7l D-C D-C73C D-C80C D-G5NT D-G D-5l D D-59W Note) djust the auto switch after confirming the operating condition in the actual setting. 356

71 uto Switch Mounting Series uto Switch Proper Mounting Position (Detection at Stroke End) Single cting, Spring Extend Type (T) uto switch model ore size D-M9l(V) D-M9lW(V) D-M9l(V) D-9l(V) D-H7l D-H7lW D-H7C D-H7 D-H7N D-C7l D-C80 D-C73C D-C80C D-G5NT D-G59 D-5l D-64 D-59W dimensions Up to 50 st 51 to 100 st 101 to 125 st 126 to 200 st Note) djust the auto switch after confirming the operating condition in the actual setting. Direct Mount Type (R, KR) uto switch D-M9l D-H7lW model D-M9lV D-C7l D-H7N D-M9lW D-9l D-C80 D-G59 D-5l D-H7 D-M9lWV D-9lV D-C73C D-G5NT D-64 D-M9l D-H7l D-C80C D-M9lV D-H7C D-59W ore size Note) djust the auto switch after confirming the operating condition in the actual setting. CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 357 D- -X Technical Data

72 Series uto Switch Proper Mounting Position (Detection at Stroke End) With End Lock () uto switch model Lock position D-M9l D-M9lV D-M9lW D-M9lWV D-M9l D-M9lV D-9l D-9lV D-H7l D-H7C D-H7lW D-H7 D-H7N D-G5lW D-K59W D-G59 D-G5 D-K5 D-G5NT D-G5 D-C7 D-C8 D-C73C D-C80C D-5 D-6 D-59W ore size Head end Rod end (32) (28) (27.5) (24) (28.5) (22.5) (25.5) Double end Head end Rod end (32) (28) (27.5) (24) (28.5) (22.5) (25.5) Double end Head end Rod end (33) (29) (28.5) (25) (29.5) (23.5) (26.5) Double end Head end Rod end (36) (32) (31.5) (28) (32.5) (26.5) (29.5) Double end Head end Rod end (44) (40) (39.5) (36) (40.5) (34.5) (37.5) Double end Head end Rod end (44) (40) (39.5) (36) (40.5) (34.5) (37.5) Double end Head end Rod end (46) (44.5) (47.5) Double end Head end Rod end (46) (44.5) (47.5) Double end Note 1) The values in ( ) are for long stroke. Note 2) djust the auto switch after confirming the operating condition in the actual setting. 358

73 uto Switch Mounting Series Minimum Stroke for uto Switch Mounting Note 1) uto switch mounting Number of auto switches n: Number of auto switches uto switch model With 2 pcs. With n pcs. With 1 pc. Different surfaces Same surface Different surfaces Same surface (n 2) D-M Note 1) 40 Note 1) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) D-M9 W Note 1) 40 Note 1) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) D-M Note 1) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) D Note 1) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) D-M9 V D-9 V D-M9 WV D-M9 V D-C7 D-C80 D-H7 D-H7 W D-H7 D-H7N D-H7C D-C73C D-C80C D-G5 D-K59 D-5 D D-59W Note 3) When n is an odd number, an even number that is one larger than this odd number is used for the calculation. With 2 auto switches (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) Different surfaces Note 1) Same surface Note 1) CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS uto switch model Correct auto switch mounting position is 3.5 mm from the back face of the switch holder. Note 2) Minimum stroke for auto switch mounting in types other than those mentioned in Note 1. The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. D-M9 D-M9 W Less than 20 stroke Note 2) Less than 55 stroke D-M9 Less than 20 stroke Note 2) Less than 60 stroke D-9 Less than 50 stroke Note 2) Note 2) Note 2) 359 D- -X Technical Data

74 Series uto Switch Mounting rackets/part No. uto switch model D-M9 (V) D-M9 W(V) D-9 (V) Note 2) D-M9 (V) M3-020S ore size M3-020 ( set of a, b, c, d) ( set of b, c, d, e) M3-025 ( set of a, b, c, d) M3-025S ( set of b, c, d, e) M3-032 ( set of a, b, c, d) M3-032S ( set of b, c, d, e) M3-040 ( set of a, b, c, d) M3-040S ( set of b, c, d, e) M3-050 ( set of a, b, c, d) M3-050S ( set of b, c, d, e) M3-063 ( set of a, b, c, d) M3-063S ( set of b, c, d, e) Switch bracket (Resin) a Transparent (Nylon) Note 1) e White (PT) uto switch b Switch holder c uto switch mounting band d uto switch mounting screw D-H7 D-H7 W D-H7N D-C7 /C80 D-C73C/C80C D-H7 D-G5 /K59 D-G5 W/K59W D-G5/G59 D-G5NT D-5 /64 D-59W D-G5N M2-020 ( set of band and screw) M2-020S ( set of band and screw) -01 ( set of band and screw) M2-025 ( set of band and screw) M2-025S ( set of band and screw) -02 ( set of band and screw) and (c) is mounted so that the projected part is on the internal side (contact side with the tube). M2-032 ( set of band and screw) M2-032S ( set of band and screw) -32 ( set of band and screw) M2-040 ( set of band and screw) M2-040S ( set of band and screw) -04 ( set of band and screw) M2-050 ( set of band and screw) M2-050S ( set of band and screw) -05 ( set of band and screw) M2-063 ( set of band and screw) M2-063S ( set of band and screw) -06 ( set of band and screw) -08 ( set of band and screw) -10 ( set of band and screw) Note 1) Since the switch bracket (made from nylon) are affected in an environment where alcohol, chloroform, methylamines, hydrochloric acid or sulfuric acid is splashed over, so it cannot be used. Please contact SMC regarding other chemicals. Note 2) s the indicator LED is projected from the switch unit, indicator LED may be damaged if the switch bracket is fixed on the indicator LED. and Mounting rackets Set Part No. Set part no. M2- (S) S: Stainless steel screw J4-1 J5-1 Contents uto switch mounting band (c) uto switch mounting screw (d) Switch bracket (White/PT) (e) Switch holder (b) Switch bracket (Transparent/Nylon) (a) Switch holder (b) [Stainless Steel Mounting Screw] The following stainless steel mounting screw kit is available. Use it in accordance with the operating environment. (Since the auto switch mounting bracket is not included, order it separately.) 3: D-5/6/G5/K5 types Note 3) Refer to page 1681 for details on the 3. When the D-G5 type auto switch is shipped independently, the 3 is attached. 360

75 uto Switch Mounting Series Operating Range uto switch model ore size D-M9 (V) D-M9 W(V) D-M9 (V) D D-C7/C80 D-C73C/C80C D-5 / D-59W D-H7 /H7 W D-H7N/H D-H7C D-G5 /G5 W/G59 D-G5/K59/K59W D-G5NT D-G5N Values which include hysteresis are for guideline purposes only, they are not a guarantee (assuming approximately ±30% dispersion) and may change substantially depending on the ambient environment. Cylinder Mounting racket, by Stroke/uto Switch Mounting Surfaces uto switch model uto switch mounting surface With 1 pc. (Rod cover side) asic, oot, lange, Clevis With 2 pcs. (Different surfaces) With 2 pcs. (Same surface) Port surface Port surface Port surface With 1 pc. (Rod cover side) Trunnion With 2 pcs. (Different surfaces) st: Stroke With 2 pcs. (Same surface) CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 uto switch type D-M9 (V) D-M9 W(V) D-M9 (V) 10 st or more 15 to 44 st 45 st or more 10 st or more 15 to 44 st 45 st or more D-9 D-C7/C8 10 st or more 15 to 49 st 50 st or more 10 st or more 15 to 49 st 50 st or more D-H7 /H7 W D-H7/H7N 10 st or more 15 to 59 st 60 st or more 10 st or more 15 to 59 st 60 st or more D-H7C/C73C/C80C 10 st or more 15 to 64 st 65 st or more 10 st or more 15 to 64 st 65 st or more D-G5/K5/5/6 D-G5 W/K59W/G5 10 st or more 15 to 74 st 75 st or more 10 st or more 15 to 74 st 75 st or more D-G59/G5NT D-59W 15 st or more 20 to 74 st 75 st or more 15 st or more 20 to 74 st 75 st or more Trunnion type is not available for ø80 and ø100. djust the auto switch mounting angle according to the customer s application. CS2 Other than the applicable auto switches listed in How to Order, the following auto switches are mountable. Refer to pages 1575 to 1701 for the detailed specifications. Type Model Electrical entry eatures pplicable bore size Solid state Reed D-H71, H72, H7 D-H7NW, H7PW, H7W D-H7 D-G5NT Grommet (In-line) With timer ø20 to ø100 With pre-wired connector is also available for solid state auto switches. or details, refer to pages 1648 and Normally closed (NC = b contact) solid state auto switches (D-9G/9H) are also available. or details, refer to page Wide range detection type, solid state auto switch (D-G5N) is also available. or details, refer to page Diagnostic indication (2-color indicator) Water resistant (2-color indicator) D-C73, C76 D-C80 Without indicator light ø20 to ø63 ø20 to ø63 D-53 ø20 to ø100 D- -X 361 Technical Data

76 Series Made to Order: Individual Specifications Please contact SMC for detailed dimensions, specifications and lead times. Symbol 1 PTE Grease -X446 pplicable to environments incompatible with mineral oil PTE grease (fluorine grease) is used as the lubricating grease. pplicable Series Description Model ction Note Standard type How to Order Standard model no. Double acting, Single rod Except with air cushion X446 Specifications: Same as standard type Dimensions: Same as standard type * When grease is necessary for maintenance, grease pack is available, please order it separately. GR--005 (Grease: 5 g) PTE grease 362

77 Series Specific Product Precautions 1 e sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages 3 to 12 for ctuator and uto Switch Precautions. <Precautions on each series> Handling Warning 1. Do not operate the cushion valve in the fully closed or fully opened state. Using it in the fully closed state will cause the cushion seal to be damaged. Using it in the fully opened state will cause the piston rod assembly or the cover to be damaged. 2. Do not turn the cushion valve the number of rotations shown below or more from its fully closed state. If it is turned the number of rotations shown below or more, the cushion valve may come off. ore size Rotations Hexagon wrench nominal size Do not open the cushion valve after rotating it numerous times in a row. Though uncommon, there are cases in which the cushion valve may leak air. The cushion valve should be adjusted by gradually opening it while checking the operation of the cylinder cushion. 4. Operate within the specified cylinder speed and kinetic energy. Otherwise, cylinder and seal damage may occur. 5. When a cylinder is operated with one end fixed and other free (basic, flange types), a bending moment may act on the cylinder due to the vibration generated at the stroke end, which can damage the cylinder. In such a case, install a mounting bracket to suppress the vibration of the cylinder body or reduce the piston speed so that the cylinder does not vibrate. lso, use a mounting bracket to suppress vibrations when moving the cylinder body or when a cylinder is operated horizontally and fixed at one end at a high speed and frequency. Caution 1. Use caution regarding the cushion performance in the low-speed range. There may be individual performance and effect variances when used near 50 mm/s. Please consult with SMC about usage. 2. Do not apply excessive lateral load to the piston rod. Easy checking method Minimum operating pressure after the cylinder is mounted to the equipment (MPa) = Minimum operating pressure of cylinder (MPa) + {Load weight (kg) x 9.8 x riction coefficient of guide/sectional area of cylinder (mm 2 )} If smooth operation is confirmed within the above value, the load on the cylinder is the resistance of the thrust only and it can be judged as having no lateral load. 3. Do not use the air cylinder as an air-hydro cylinder. This may result in oil leak. 4. Install a rod boot without twisting. If the cylinder is installed with its bellows twisted, it could damage the bellows. 5. Tighten clevis bracket mounting bolts with the following proper tightening torque. ø20: 1.5 N m, ø25 to 32: 2.9 N m, ø40: 4.9 N m, ø50: 11.8 N m, ø63 to 80: 24.5 N m, ø100: 42.2 N m Warning Disassembly/Replacement 1. Only people who have sufficient knowledge and experience are allowed to replace seals. The person who disassembles and reassembles the cylinder is responsible for the safety of the product. Repeatedly disassembling and reassembling the product may cause wearing or deformation of the screws as well as a decline in screw tightening strength. When reassembling the product, be sure to check the cover and tubing screws for wear, deformities, or any other abnormalities. Operating the product with damaged screws may result in the cover or tubing coming off during operation, which could lead to a serious accident. Caution must be taken to avoid such incidents. Caution 1. Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3. Cylinders with ø50 or larger bore sizes cannot be disassembled. When disassembling cylinders with bore sizes of ø20 through ø40, grip the double flat part of either the tube cover or the rod cover with a vise and loosen the other side with a wrench or a monkey wrench etc., and then remove the cover. When re-tightening, tighten approximately 2 degrees more than the original position. (Cylinders with ø50 or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. If disassembly is required, please contact SMC.) 4. When replacing seals, take care not to hurt your hand or finger on the corners of parts. <Precautions on the non-rotating rod type> Handling Caution 1. void using the air cylinder in such a way that rotational torque would be applied to the piston rod. If rotational torque is applied, the non-rotating guide will become deformed, thus affecting the non-rotating accuracy. Refer to the table below for the approximate values of the allowable range of rotational torque. llowable rotational torque (N m or less) To screw a bracket or a nut onto the piston rod, make sure to retract the piston rod entirely, and place a wrench over the flat portion of the rod that protrudes. Tighten it by giving consideration to prevent the tightening torque from being applied to the non-rotating guide. Caution ø20 ø25, ø32 ø40, ø50, ø Disassembly/Replacement 1. When replacing rod seals, please contact SMC. ir leakage may be happened, depending on the position in which a rod seal is fitted. Thus, please contact SMC when replacing them CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 D- -X Technical Data

78 Series Specific Product Precautions 2 e sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages 3 to 12 for ctuator and uto Switch Precautions. <End Lock Cylinder Precautions> Use the Recommended Pneumatic Circuit Caution This is necessary for proper operation and release of the lock. W Warning Handling 1. Do not operate the cushion valve in the fully closed or fully opened state. Using it in the fully closed state will cause the cushion seal to be damaged. Using it in the fully opened state will cause the piston rod assembly or the cover to be damaged. 2. Operate within the specified cylinder speed. Otherwise, cylinder and seal damage may occur. Operating Pressure Caution 1. Supply air pressure of 0.15 MPa or higher to the port on the lock mechanism side, as it is necessary for releasing the lock. W Head end lock Caution Handling Rod end lock 1. Do not use 3 position solenoid valves. void use in combination with 3 position solenoid valves (especially closed center metal seal types). If pressure is trapped in the port on the lock mechanism side, the cylinder cannot be locked. urthermore, even after being locked, the lock may be released after some time, due to air leaking from the solenoid valve and entering the cylinder. 2. ack pressure is required when releasing the lock. e sure air is supplied to the side of the cylinder without a lock mechanism, (side of the piston rod without lock for double end lock), before starting up, as in the above figures. Otherwise, the lock may not be released. (Refer to Releasing the Lock.) 3. Release the lock when mounting or adjusting the cylinder. If mounting or other work is performed when the cylinder is locked, the lock unit may be damaged. 4. Operate with a load ratio of 50% or less. If the load ratio exceeds 50%, this may cause problems such as failure of the lock to release, or damage to the lock unit. 5. Do not operate multiple cylinders in synchronization. void applications in which two or more cylinders with end lock are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required. 6. Use a speed controller with meter-out control. Lock cannot be released occasionally by meter-in control. 7. e sure to operate completely to the cylinder stroke end on the side with the lock. If the cylinder piston does not reach the end of the stroke, locking and unlocking may not be possible. 8. Do not use the air cylinder as an air-hydro cylinder. This may result in oil leak. 9. Install a rod boot without twisting. If the cylinder is installed with its bellows twisted, it could damage the bellows. 10. djust an auto switch position so that it operates for movement to both the stroke end and backlash (2 mm) positions. When a 2-color indicator switch is adjusted for green indication at the stroke end, it may change to red for the backlash return, but this is not abnormal Exhaust Speed Caution 1. The lock will be engaged automatically if the pressure applied to the port on the lock mechanism side falls to 0.05 MPa or less. In cases where the piping on the lock mechanism side is long and thin, or the speed controller is separated at some distance from the cylinder port, the exhaust speed will be reduced. Take note that some time may be required for the lock to engage. In addition, clogging of a silencer mounted on the solenoid valve exhaust port can produce the same effect. Relation to Cushion Caution 1. When cushion valve at lock mechanism side is fully opened or closed, piston rod may not be reached at stroke end. Thus, lock is not established. nd when locking is done at cushion valve fully closed, adjust cushion valve since lock may not be released. Releasing the Lock Warning 1. efore releasing the lock, be sure to supply air to the side without a lock mechanism, so that there is no load applied to the lock mechanism when it is released. (Refer to the recommended pneumatic circuits.) If the lock is released when the port on the other side is in an exhaust state, and with a load applied to the lock unit, the lock unit may be subjected to an excessive force and be damaged. urthermore, sudden movement of the piston rod is very dangerous. Disassembly/Replacement Caution 1. Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3. Cylinders with ø50 or larger bore sizes cannot be disassembled. When disassembling cylinders with bore sizes of ø20 through ø40, grip the double flat part of either the tube cover or the rod cover with a vise and loosen the other side with a wrench or a monkey wrench etc., and then remove the cover. When retightening, tighten approximately 2 degrees more than the original position. (Cylinders with ø50 or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. If disassembly is required, please contact SMC.)

79 Series Specific Product Precautions 3 e sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages 3 to 12 for ctuator and uto Switch Precautions. Caution Manual Release 1. Non-locking type manual release Insert the accessory bolt from the top of the rubber cap (it is not necessary to remove the rubber cap), and after screwing it into the lock piston, pull it to release the lock. If you stop pulling the bolt, the lock will return to an operational state. Thread sizes, pulling forces and strokes are as shown below. ore size Thread size Pulling force Stroke 20, 25, 32 M2.5 x 0.45 x 25 L or more 4.9 N 2 40, 50, 63 M3 x 0.5 x 30 L or more 10 N 3 80, 100 M5 x 0.8 x 40 L or more 24.5 N 3 Remove the bolt for normal operation. It can cause lock malfunction or faulty release. Rubber cap 2. Locking type manual release While pushing the M/O knob, turn it 90 counterclockwise. The lock is released (and remains in a released state) by aligning the mark on the cap with the O mark on the M/O knob. When locking is desired, turn the M/O knob 90 clockwise while pushing completely down, and align the mark on the cap with the ON mark on the M/O knob. The correct position is confirmed by a clicking sound. ailure to click it into place properly can cause the lock to disengage. Pressure Piston rod Working Principle * The figures below are the same as those for C2 series. PHead end lock (Rod end lock is the same.) 1. When the piston rod is getting closer to the stroke end, the taper part (*) of the piston rod edge will push the lock piston up. 2. The lock piston is pushed up further. Spring Lock piston 3. The lock piston is pushed up into the groove of the piston rod to lock it. (The lock piston is pushed up by spring force.) t this time, it is exhausted from the port on the head side and introduced into the atmosphere. CJ1 CJP CJ2 JCM CM2 CM3 JM M M1 C2 CS1 CS2 Release Lock Locked state 4. When pressure is supplied in the head side, lock piston will be pushed up to release the lock. ack pressure Locked state Unlocked state Exhaust Unlocked state Pressure 5. When the lock is released, the cylinder will move forward. Exhaust D- -X Technical Data