Compact Guide Cylinder

Size: px
Start display at page:

Download "Compact Guide Cylinder"

Transcription

1 Compact Guide Cylinder Series ø2, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Series standard type and series high precision ball bushing bearing type (except with end lock) products have been remodeled for a lightweight design. When selecting a product, refer to the new -Z series. MGJ -Z W MGQ MGG MGC MGF MGZ Series Variations Series Bearing type Cushion Page MGT Standard type Rubber bumper P. 343 With air cushion With end lock Slide bearing Ball bushing bearing ir cushion Rubber bumper P. 3 P. 3 Heavy duty guide rod type S Slide bearing Rubber bumper P. 390 High precision ball bushing bearing type Ball bushing bearing Rubber bumper/ ir cushion P. 399 D X

2 Combinations of Standard Products and Made Series : Standard : Made to Order specifications : Special product (Contact SMC for details.) : Not available Basic type ir cushion Bearing Slide bearing Ball bushing Slide bearing Ball bushing Type M L M L ø2 to 0 ø to 0 Basic type With air cushion With end lock 2- Clean series Note ) 3- Clean series Note ) 2- Copper (Cu)-free Note 7) 2- Copper (Cu) and zinc (Zn)-free Note 7) - Copper Note ) /Fluorine-free 2- Copper-free/Clean series Note ) R/V Water resistant Note 2) XB Heat resistant cylinder ( to C) Note 3) XB9 Low speed cylinder ( to mm/s) XB Intermediate stroke (Exclusive body) XB3 Low speed cylinder ( to mm/s) XB22 Shock absorber/soft type XC4 With heavy duty scraper Note 4) XC Made of stainless steel XC8 djustable stroke cylinder/djustable extension type XC9 djustable stroke cylinder/djustable retraction type XC9 Intermediate stroke (Spacer type) XC22 Fluororubber seals Note ) XC3 With coil scraper Note 4) XC9 With shock absorber XC79 Machining tapped hole, drilled hole and pin hole additionally XC82 Bottom mounting style XC92 Dust resistant cylinder X44 Symmetrical port position X87 Lateral piping type (Change of plug position) Note ) L: 2 to only Note 2) L: to 0 only Note 3) Without cushion, L: (). (): With auto switch 338 Note 4) For ø to ø0 only Note ) Without cushion, L: (). Note ) Copper-free for the externally exposed part. Note 7) For details, refer to the SMC website.

3 Series to Order Specifications With end lock Heavy duty guide type M L Slide bearing Ball bushing ø to 0 S Slide bearing ø, ø Basic type ø2 to 0 High precision ball bushing type ir cushion ø to 0 With end lock ø to MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

4 Compact Guide Cylinder Series ø2, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Four mounting styles provided. Top mounting Easy positioning Knock pin holes provided on each mounting surface 2. Side mounting Piping is possible from two directions. Top ported 3. T-slot side mounting Easy adjustment of workpiece and cylinder mounting. Top mounting 2. Side ported 4. Bottom mounting 2d or more (d: Screw O.D.) 2. Side port uto switches can be mounted on two sides.. Top port 2. Side mounting. uto switch mounting 4. Bottom mounting. uto switch mounting 3. T-slot side mounting Two types of guide rod bearing to accommodate various applications Slide bearing The lateral withstand load is more than twice that of a conventional stopper cylinder (round bar type), and is suitable for use with lateral loads accompanied by impact, as in stoppers. Ball bushing bearing Suitable for use as a pusher and lifter. Long strokes up to 0 mm are standardized. Stroke Variations Bearing type M Slide bearing L Ball bushing bearing Stroke Intermediate stroke Spacer installation type vailable by the mm & mm interval. Exclusive body (-XB) in stroke increments of mm 3

5 With end lock type Stroke Variations Bearing type M Slide bearing L Ball bushing bearing 2 0 Holds the cylinder, s home position even if the air supply is cut off. Compact body ø to ø Standard + 2 mm body length ø, ø0 Standard + mm body length Stroke Intermediate stroke Spacer type available by the mm stroke interval. Lock direction Rod end lock Head end lock Manual release Non-lock type Lock type With air cushion type n air cushion has been added to the compact guide cylinder to suppress vibration and noise at the stroke end. It can absorb nearly three times as much kinetic energy as a rubber bumper. Cushion valve is built into the body Stroke Variations Bearing type M Slide bearing L Ball bushing bearing 2 0 Stroke Heavy duty guide rod type with improved load resistance Intermediate stroke Strokes available by the mm interval by changing the collar. MGJ -Z W MGQ MGG MGC MGF MGZ MGT Stroke Variations Bearing type S Slide bearing Stroke nti-lateral load: % increase Eccentric load resistance: 2% increase Impact load resistance: % increase (Compared with M compact guide cylinder) Guide rod diameter S M D- -X

6 Full Made to Order Variation Description Heat resistant cylinder ( to C) Symbol -XB n air cylinder with special seal material and grease, so that it can be used even at an ambient temperature range from C up to C. (M only) Intermediate stroke (Using exclusive body) Symbol -XB When intermediate strokes other than standard strokes are used, this cylinder could shorten the full length and reduce the mounting space with an exclusive body without a spacer. Low speed cylinder ( to mm/s) Symbol -XB3 Smooth operation is possible with minimal sticking and slipping at low speeds of to mm. With heavy duty scraper Symbol -XC4 cylinder with a heavy duty scraper is used for the wiper ring is suitable for use in an environment where there is a lot of dust in the surrounding area or where the equipment is exposed to earth and sand (die-casting equipment, construction machinery, industrial vehicles, etc.). Change of guide rod end shape Symbol -X,,7,2 Some patterns of guide rod end shape. 4 diagrams are available. Specify dimensions on a drawing and order the desired product. (Standard body dimension) E With coil scraper With shock absorber Description Shock absorber Machining tapped hole, drilled hole and pin hole additionally Plate Symbol -XC3 It gets rid of frost, ice, weld spatter, cutting chips adhered to the piston rod, and protects the seals, etc. -XC9 Symbol -XB22 shock absorber reduces the impact on the stroke extended side end. Symbol -XC79 Tapped, drilled and pin holes are additionally machined to install a workpiece to the plate. Piston rod and rod end nut made of stainless steel Retaining ring Piston rod 2 Guide rod 3 Plate 4 Plate mounting bolt Symbol -XC Hexagon socket These are suitable for cases head cap plug where rust or corrosion due to being immersed in water are likely. Use stainless steel for parts q to y. djustable stroke cylinder/djustable extension type Symbol -XC8 Install a stroke adjusting unit on the head side to adjust strokes at the outlet. (fter adjusting stroke, both-side cushion style is changed into single side cushion style.) Bottom mounting style Relief holes for the guide rods are not required when a cylinder is mounted on the bottom. Symmetrical port position Standard -X44 Symbol -XC82 The guide rod does not protrude from the bottom when the rod is retracting. Symbol -X44 This makes it easy to remove and rotate piping when it is mounted on a wall where mounting space is limited. djustable stroke cylinder/djustable retraction type Symbol -XC9 The retract stroke of the cylinder can be adjusted with the adjusting bolt. Lateral piping type (Change of plug position) Symbol -X87 type which plugs the piping port on the top in order to use it on the side. Intermediate stroke (Spacer type) Symbol -XC9 When intermediate strokes other than standard strokes are used, this cylinder could shorten the full length and reduce the mounting space with a spacer. Fluororubber seals Symbol -XC22 Fluororubber is used for seals. Hexagon socket head cap taper plug Front piping port Side piping port 342

7 Compact Guide Cylinder Series ø2, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Series standard type has been remodeled for a lightweight design. When selecting a product, refer to the new -Z series. MGJ -Z W MGQ MGG MGC MGF MGZ MGT Stroke Variations Bearing type M Slide bearing L Ball bushing bearing Stroke Intermediate stroke Spacer installation type vailable by the mm & mm interval. Exclusive body (-XB) in stroke increments of mm 343 D- -X

8 Series Specific Product Precautions Be sure to read before handling. Refer to front matter 39 for Safety Instructions and pages 3 to 2 for ctuator and uto Switch Precautions Warning Caution Series B C D Hexagon socket M L head cap screw 4 8 M4 x M x M x M x M8 x M8 x M x M x M2 x M4 x 2.0 Mounting. Never place your hands or fingers between the plate and the body. Be very careful to prevent your hands or fingers from getting caught in the gap between the cylinder body and the plate when air is applied.. Use cylinders within the piston speed range. n orifice is set for this cylinder, but the piston speed may exceed the operating range if the speed controller is not used. If the cylinder is used outside the allowable speed range, it may cause damage to the cylinder and shorten the service life. djust the speed by installing the speed controller and use the cylinder within the limited range. 2. Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals, etc. will result in leakage or malfunction. 3. Do not dent or scratch the mounting surface of a body and a plate. The flatness of the mounting surface may not be maintained, which would cause an increase in sliding resistance. 4. Make sure that the cylinder mounting surface has a flatness of 0.0 mm or less. If the flatness of the workpieces and brackets mounted on the plate is not appropriate, sliding resistance may increase.. Bottom of cylinder The guide rods protrude from the bottom of the cylinder at the end of the retracting stroke, and therefore, in cases where the cylinder is to be bottom mounted, it is necessary to provide bypass ports in the mounting surface for the guide rods, as well as holes for the hexagon socket head screws which are used for mounting. Moreover, in applications where impact occurs from a stopper, etc., the mounting bolts should be inserted to a depth of 2 d or more (. d or more for S). 344 ±0.2 2 d or more (d = Thread O.D.) ød C ±0.2 Bypass port dia. ±0.2 B Series S B C ±0.2 ±0.2 C 70 D 47. d or more (d = Thread O.D.) ød Bypass port dia. B ±0.2 Hexagon socket head cap screw M2 x.7 M x 2 Cushion With air cushion Warning. Do not open the cushion valve excessively. ir leakage will occur if operated after opening by 4 rotations or more. Furthermore, a stopper mechanism is provided for the cushion valve, and it should not be forced open beyond that position. Be aware that the cushion valve may jump up from the cover when the air is supplied. Caution. Be sure to use the cylinder after the air cushion has been adjusted appropriately. First, fully close the cushion valve. Start the operation at the cylinder speed to be used with the load applied, and then open the cushion valve gradually to make the adjustment. The optimal adjustment is that the piston reaches its stroke end and the collision sound is minimized. If the cushion valve is used without adjusting the air cushion appropriately, this may cause damage to the retaining ring or piston. pplicable tool Flat head watchmakers, screwdriver 3 mm,2,, JIS B 448 hexagon wrench key., JIS B 448 hexagon wrench key 2.,0 JIS B 448 hexagon wrench key 4 2. Be sure to operate a cylinder equipped with air cushion to the end of the stroke. If it is not operated to the end of the stroke, the effect of the air cushion will not be fully exhibited. Consequently, in cases where the stroke is regulated by an external stopper, etc., caution must be exercised, as the air cushion may become completely ineffective. Piping Caution Depending on the operating conditions, piping port positions can be changed by using a plug.. For M fter tightening by hand, tighten additional / to /4 rotation with a tightening tool. 2. For taper thread Use the correct tightening torques listed below. Before tightening the plug, wrap pipe tape around it. lso, with regard to the sunk dimension of a plug (a dimension in the drawing), use the stipulated figures as a guide and confirm the air leakage before operation. If tightening plugs on the top mounting port with more than the proper tightening torque, plugs will be screwed much deeply and air passage will be squeezed. Consequently, the cylinder speed will be restricted. Connection thread (plug) size /8 /4 3/8 Plug Proper tightening torque (N m) 7 to 9 2 to 4 22 to a dimension 0. mm or less mm or less mm or less a

9 Series Specific Product Precautions 2 Be sure to read before handling. Refer to front matter 39 for Safety Instructions and pages 3 to 2 for ctuator and uto Switch Precautions. llowable Kinetic Energy Load mass and a maximum speed must be within the ranges shown in the graphs below. with rubber bumper with air cushion ø0 ø ø ø ø ø ø2 ø ø ø2 0 ø0 ø ø ø ø ø Maximum speed (mm/s) without cushion (-V (Water resistant), XB, XC9, XC22) 00 0 ø0 ø ø ø ø ø ø2 ø ø ø2 ø2 ø ø 0 00 Maximum speed (mm/s) MGJ -Z W MGQ MGG MGC MGF MGZ MGT Maximum speed (mm/s) 34 D- -X

10 Compact Guide Cylinder Series ø2, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 How to Order Series standard type has been remodeled for a lightweight design. When selecting a product, refer to the new -Z series. M 2 M9BW Compact Guide Cylinder M L Bearing type Slide bearing Ball bushing bearing mm mm mm 2 mm mm 0 mm mm mm mm 0 mm Thread type Nil N TF M x 0.8 Rc NPT G For bore sizes 2 and, only M x 0.8 is available. uto switch Without auto switch Nil (Built-in magnet) For the applicable auto switch model, refer to the table below. Cylinder stroke Refer to Standard Stroke on page 347. Number of auto switches Nil S n 2 pcs. pc. n pcs. Made to Order Specification For details, refer to page 347. pplicable uto Switches/Refer to pages 893 to 07 for further information on auto switches. Type Reed auto switch Solid state auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) Magnetic field resistant (2-color indication) Electrical entry Indicator light Wiring (Output) Load voltage DC 3-wire (NPN) 3-wire (PNP) 2-wire V,2 V 2 V 3-wire (NPN) Grommet Yes 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire V V,2 V 2 V V,2 V 2 V 2-wire (Non-polar) 3-wire Yes (NPN equivalent) Grommet V No 2-wire V 2 V Lead wire length symbols: 0. m Nil (Example) M9NW m M (Example) M9NWM 3 m L (Example) M9NWL m Z (Example) M9NWZ C 0 V 0 V or less uto switch model Perpendicular In-line M9NV M9PV M9BV M9NWV M9PWV M9BWV M9NV M9PV M9BV 9V 93V 2 90V M9N M9P M9B M9NW M9PW M9BW M9N M9P M9B P3DW P4DW Lead wire length (m) 0. (Nil) (M) (Z) Pre-wired connector pplicable load Solid state auto switches marked with are produced upon receipt of order. s to 0 are available for D-P4DW. s 2 to 0 are available for D-P3DW. Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages 90 and 9. For D-P3DW, refer to pages 948 and 949. uto switches are shipped together (not assembled). 3 (L) IC circuit IC circuit IC circuit IC circuit IC circuit Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. water resistant type cylinder is recommended for use in an environment which requires water resistance. Consult with SMC regarding water resistant types for ø2 and ø. 2 m type lead wire is only applicable to D-93. Relay, PLC Relay, PLC B 34

11 Minimum Proper Operating uto Compact Guide Cylinder Series Specifications ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Note) Cushion Lubrication Stroke length tolerance Standard Stroke ø2 ø ø ø2 ø ø ø ø ø ø0 Double acting ir. MPa.0 MPa 0.2 MPa 0. MPa to 0 C (No freezing) to 0 mm/s to 0 mm/s Rubber bumper on both ends Not required (Non-lube) +. 0 mm Note) Maximum speed with no load. Make a model selection, considering a load according to the graph on pages 349 to 3. Symbol Rubber bumper 2,, 2 to 0 Standard stroke,,,,, 7, 0, 2,, 7, 0, 2,,,, 7, 0, 2,, 7, 0, 2, 0, 3, 0 2,, 7, 0, 2,, 7, 0, 2, 0, 3, 0 Manufacture of Intermediate Stroke Symbol Made to Order: Individual Specifications (For details, refer to pages 7 and 8.) Specifications -X44 Symmetrical port position -X87 Lateral piping type (Change of plug position) Made to Order Specification (For details, refer to pages 09 to 22.) Symbol Specifications X Change of guide rod end shape XB Heat resistant cylinder ( to C) XB Intermediate stroke (Using exclusive body) XB3 Low speed cylinder ( to mm/s) XB22 Shock absorber soft type Series RJ type XC4 With heavy duty scraper XC Made of stainless steel XC8 djustable stroke cylinder/djustable extension type XC9 djustable stroke cylinder/djustable retraction type XC22 Fluororubber seals XC3 With coil scraper XC9 With shock absorber XC79 Machining tapped hole, drilled hole and pin hole additionally. XC82 Bottom mounting style XC92 Dust resistant cylinder Refer to pages 4 to for cylinders with auto switches. auto switch mounting stroke auto switch mounting position (detection at stroke end) and mounting height range switch mounting bracket: Part no. Description Part no. pplicable stroke Example Theoretical Output Rod size Spacer installation type Spacers are installed in the standard stroke cylinder. ø2 to : vailable by the mm stroke interval. ø to 0: vailable by the mm stroke interval. Refer to How to Order for the standard model numbers. ø2, ø to 9 ø, ø2, ø to 399 ø to ø0 to 39 Part no.: M-39 spacer mm in width is installed in a M-. C dimension is 77 mm. Operating direction Piston area (mm 2) Exclusive body (-XB) Dealing with the stroke by making an exclusive body. ll bore sizes are available by the mm interval. Suffix -XB to the end of standard part number. Note) ø2, ø to 9 ø, ø2 2 to 399 ø to ø0 2 to 399 Part no.: M-39-XB Special body manufactured for 39 stroke. C dimension is 7 mm. Operating pressure (MPa) OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2) OUT IN (N) 347 MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

12 +θ θ Weight llowable Rotational Torque of Plate Non-rotating ccuracy of Plate Slide Bearing: M2 to 0 Standard stroke M2 M M M2 M M M M M M0 Model (kg) Ball Bushing Bearing: L2 to (kg) Standard stroke L2 L L L2 L L L L L L0 Model Non-rotating accuracy θ M L ±0.08 ±0. ±0.07 ±0.09 ±0.0 ±0.08 ±0.0 ±0.0 ±0.04 ±0.0 Torque: T (N m) Stroke 2 M L M L M L M L M L Bearing type T (N.m) 2 0 M L M L M L M L M L For non-rotating accuracy without load, use a value no more than the values in the table as a guide. Series 348

13 Series Model Selection Selection Conditions Vertical Horizontal L L L L m m Mounting orientation m m Maximum speed (mm/s) 0 or less 0 0 or less 0 Graph (Slide bearing type) Graph (Ball bushing bearing type) (), (2) () to (8) (3), (4) (9) to (2) (3), (4) (7), (8) (), () (9), () Selection Example (Vertical Mounting) Selection Example 2 (Horizontal Mounting) MGJ Selection conditions Mounting: Vertical Bearing type: Ball bushing Stroke: stroke Maximum speed: 0 mm/s Load mass: 3 kg Eccentric distance: 90 mm Find the point of intersection for the load mass of 3 kg and the eccentric distance of 90 mm on graph (), based on vertical mounting, ball bushing, stroke, and the speed of 0 mm/s. L2- is selected. ø2 ø ø ø2 Selection conditions Mounting: Horizontal Bearing type: Slide bearing Distance between plate and load center of gravity: mm Maximum speed: 0 mm/s Load mass: 2 kg Stroke: stroke Find the point of intersection for the load mass of 2 kg and stroke on graph (3), based on horizontal mounting, slide bearing, the distance of mm between the plate and load center of gravity, and the speed of 0 mm/s. M- is selected. () stroke or less, V = 0 mm/s or less (3) L = mm, V = 0 mm/s or less ø0 ø ø, ø, ø2 ø ø ø2 ø0 ø ø, ø, ø2 ø ø ø2 -Z W MGQ MGG MGC MGF MGZ MGT Eccentric distance L Stroke. When the maximum speed exceeds 0 mm/s, the allowable load mass is determined by multiplying the value shown in the graph at 0 mm/s by the coefficient listed in the table below. Maximum Coefficient Up to 0 mm/s.7 Up to 0 mm/s Up to 0 mm/s 0.. Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more. 349 D- -X

14 Series Vertical Mounting (Slide Bearing) Operating pressure 0.4 MPa Operating pressure 0. MPa or more M2 to 0 () Stroke or Less, V = 0 mm/s or less (2) Over Stroke, V = 0 mm/s or less 0 0 ø0 0 0 ø0 0 ø ø 0 ø ø ø ø ø ø ø ø ø2 ø ø ø2 ø ø ø2 ø Eccentric distance L Eccentric distance L (3) Stroke or Less, V = 0 mm/s (4) Over Stroke, V = 0 mm/s 0 0 ø0 ø0 ø ø ø ø ø ø ø ø ø2 ø ø ø ø ø2 ø ø ø2 ø Eccentric distance L Eccentric distance L. Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more. 3

15 Model Selection Series Vertical Mounting (Ball Bushing) Operating pressure 0.4 MPa Operating pressure 0. MPa or more L2 to 2 () Stroke or Less, V = 0 mm/s or less () Over Stroke, V = 0 mm/s or less ø2 ø ø2 ø ø ø2 ø ø Eccentric distance L Eccentric distance L L to 0 (7) Stroke or Less, V = 0 mm/s or less (8) Over Stroke, V = 0 mm/s or less 0 0 ø0 ø0 ø 0 0 ø ø ø ø MGJ -Z W MGQ MGG MGC MGF MGZ MGT ø ø ø ø ø 0 0 Eccentric distance L. Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more. 0 0 Eccentric distance L 3 D- -X

16 Series Vertical Mounting (Ball Bushing) Operating pressure 0.4 MPa L2 to 2 (9) Stroke or Less, V = 0 mm/s () Over Stroke, V = 0 mm/s 0. ø2 ø2 ø ø ø 0. ø ø2 ø Eccentric distance L Eccentric distance L L to 0 () Stroke or Less, V = 0 mm/s (2) Over Stroke, V = 0 mm/s 0 0 ø0 ø ø0 ø ø ø ø ø ø ø ø ø 0 0 Eccentric distance L Eccentric distance L. Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more.

17 Model Selection Series Horizontal Mounting (Slide Bearing) M2 to 0 (3) L = mm, V = 0 mm/s or less (4) L = 0 mm, V = 0 mm/s or less ø0 ø ø0 ø0 ø0 ø ø ø ø, ø, ø, ø, ø, ø, ø, ø2 ø, ø2 ø ø ø2 ø ø ø2 ø ø2 ø2 ø ø ø ø2 ø Stroke ø0 ø ø, ø ø ø2 ø ø Stroke () L = mm, V = 0 mm/s () L = 0 mm, V = 0 mm/s ø0 ø ø ø ø ø ø2 ø ø ø0 ø ø ø ø ø ø2 ø ø ø0 ø ø, ø ø ø2 ø ø MGJ -Z W MGQ MGG MGC MGF MGZ MGT ø2 ø2 ø2 ø Stroke Stroke 33 D- -X

18 Series Horizontal Mounting (Ball Bushing) (7) L = mm, V = 0 mm/s or less (8) L =0 mm, V = 0 mm/s or less L2 to 2 L2 to 2 ø2 ø2 ø ø ø ø ø2 ø ø2 ø2 ø ø ø2 ø ø ø ø2 ø2 ø ø2 ø ø2 ø2 ø L to Stroke L to Stroke ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, Stroke L, 0 L, 0 Stroke ø0 ø0 ø0 ø0 ø ø ø ø0 ø0 ø ø ø Stroke Stroke 34

19 Model Selection Series Horizontal Mounting (Ball Bushing) (9) L = mm, V = 0 mm/s () L =0 mm, V = 0 mm/s L2 to 2 L2 to 2 ø2 ø2 ø2 ø2 ø2 ø2 ø ø ø ø ø ø ø ø ø ø ø ø ø2 ø2 ø L to ø, ø ø L, 0 Stroke ø, ø ø Stroke ø ø ø ø ø2 ø2 ø L to ø, ø ø L, 0 Stroke ø, ø ø Stroke ø ø ø ø MGJ -Z W MGQ MGG MGC MGF MGZ MGT ø0 ø0 ø0 ø0 ø ø ø ø0 ø ø0 ø ø Stroke Stroke 3 D- -X

20 Series Operating Range when Used as Stopper Bore Size: ø2 to 2/M2 to 2 (Slide bearing) M2 to 2 (Slide bearing) L mm υ m L mm υ m When selecting a model with a longer L dimension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Note ) When using as a stopper, select a model with stroke or less. Note 2) Model L (Ball bushing bearing) cannot be used as a stopper. Mass of transferred object: m (kg) ø2 ø ø ø2 Transfer speed: υ (m/min) Bore Size: ø to 0/M to 0 (Slide bearing) L mm m υ L mm m When selecting a model with a longer L dimension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Note ) When using as a stopper, select a model with stroke or less. Note 2) Model L (Ball bushing bearing) cannot be used as a stopper. υ M to 0 (Slide bearing) Mass of transferred object: m (kg) ø0 ø ø ø ø ø Transfer speed: υ (m/min) 3

21 Compact Guide Cylinder Series. Water Resistant 2. Clean Series Ideal for use in a machine tool environment exposed to coolants. pplicable for use in an environment with water splashing such as food processing and car wash equipment, etc. Specifications pplicable series Bearing type MR Cushion MV M Slide bearing, 2,,,,,, 0 Rubber bumper Without cushion Specifications other than above are the same as standard, basic style. Note) Refer to Best Pneumatics No. 2 for details. How to Order M R Stroke M9(V)L 2 Water resistant 2-color Thread type indication solid state switch Nil Rc Water resistant cylinder N NPT R NBR seals (Nitrile rubber) TF G V FKM seals (Fluororubber) Stainless steel parts are available as made-to-order products. Piston rod and guide rod are made of stainless steel. Dimensions pplicable in a clean room environment.ideal for use in conveyor lines for semiconductor (LSI), liquid crystal (LCD), food processing, pharmaceutical, and electronic parts, etc. Specifications pplicable series Bearing type L Ball bushing bearing 2 2 Stroke to 2 to 0 2 to 0 Specifications other than above are the same as standard, basic style. How to Order L Clean room specifications 2 3 Relief port type Vacuum port type Dimensions Stroke Thread type M x 0.8 Nil Rc N NPT TF G For bore sizes 2 and, M x 0.8 is only available. M x 0.8 Relief port (Vacuum port) MGJ -Z 2 0 st or less FB Over st to 0 st B + Stroke + Stroke Over 0 st Other dimensions are the same as standard type. B FB st or less st or less FB B + Stroke + Stroke Over st to 0 st Over st to 0 st 2 2 Over 0 st to 0 st Over 0 st to 0 st 4 4 Over 0 st Over 0 st Other dimensions are the same as standard products. B 9. B FB FB W MGQ MGG MGC MGF MGZ MGT D- 37 -X

22 Series Construction/Series M M2 to 2 M to 0 e u q!7 w!!0 r! e y r stroke @3 ø2, ø stroke or less t ø or more ø2, ø Over stroke ø, ø2 Over stroke ø or more Component Parts No. Description Material Note Body 2 Piston 3 Piston rod 4 Collar Bushing Head cover Guide rod Plate Plate mounting bolt Guide bolt Retaining ring Retaining ring Bumper Bumper B Magnet Plug Hexagon socket head cap plug Slide Bearing luminum alloy luminum alloy Stainless steel Carbon steel luminum bearing alloy luminum alloy casted Bearing alloy luminum alloy Carbon steel Carbon steel Carbon steel Carbon steel Carbon tool steel Carbon tool steel Urethane Urethane Carbon steel Bearing alloy Hard anodized Chromated ø2 to ø2 ø to ø0 ø2 to ø ø to ø0 ø to ø0 ø2 to ø ø to ø0 Hard chrome plated Clear anodized Painted Chromated Painted Hard chrome plated Nickel plated Nickel plated Nickel plated Phosphate coated Phosphate coated ø2, ø ø to ø0 Nickel plated Component Parts No. Description Material Note Felt Holder Ball bushing Spacer Felt Resin luminum alloy Steel ball Plug Carbon steel Carbon steel ø2 to ø ø to ø0 Nickel plated Piston seal 2 Rod seal 2 Gasket 27 Gasket B NBR NBR NBR NBR Replacement Parts: Seal Kit 2 2 Kit no. 2-PS -PS -PS 2-PS -PS 27 Contents Set of nos. above, 2, 2, 27 0 Kit no. -PS -PS -PS -PS 0-PS Seal kit includes to. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S-0 ( g) Contents Set of nos. above, 2, 2, 27 38

23 Compact Guide Cylinder Series Construction/Series L L2 to 2 L stroke or less ø or more ø2, ø stroke or less ø2, ø Over stroke ø, ø2 Over 0 ø or more ø to Over 0 MGJ -Z W MGQ MGG MGC MGF MGZ MGT 39 D- -X

24 b a 3 Series M, L: ø2 to ø2 4 x YY depth YL øx H7 depth T-slot dimensions XB øx H7 X H7 3 Detailed figure of section XX X WB Z W Bottom view X ±0.02 Section XX 2 2 c e a d T-slot dimensions b c d e ø2, ø 4 x NN through Section XX Z W 4 x øo through 4 x øob counterbore depth OL L 4 x MM depth ML Section XX (OL) ødb T R X ±0.02 ød PW X U X ±0.02 H: T-slot for hexagon bolt VB V H øx H7depth Q S G P + Stroke F FB C + Stroke B + Stroke + Stroke GB E 2 x P 2 x P (Plug) PB J G K øx H7 depth For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Stroke on page 347. M, L Common Dimensions M (Slide bearing), DB, E Dimensions Standard stroke,,,,, 7, 0 2,, 7, 0, 2,,,, 7, 0 2,, 7, 0 2, 0, 3, B P PB PW Q C R D 8 2 S F FB G G GB H H J 8 8 T M4 M4 M M K L (Ball bushing bearing), DB, E Dimensions E E DB DB st or less Over st Over 0 st to 0 st to 0 st Over 0 st st or less Over st Over 0 st to 0 st to 0 st Over 0 st st or less Over st Over 0 st to 0 st to 0 st Over 0 st st or less Over st Over to 0 st 0 st Over 0 st to 0 st L MM M4 x 0.7 M x 0.8 M x 0.8 M x For bore sizes with ø2 and ø only, M x 0.8 is available. Rc, NPT, G port can be selected for bore sizes with ø or ML more. (Refer to page 34.) NN M4 x 0.7 M x 0.8 M x 0.8 M x O OB OL P Nil N TF M x 0.8 M x 0.8 Rc /8 Rc /8 U V W WB VB st or less Over st Over 0 st Over 0 st to 0 st to 0 st to 0 st Over 0 st st or less Over st Over 0 st Over 0 st to 0 st to 0 st to 0 st Over 0 st X X XB NPT /8 NPT /8 YY M x 0.8 M x 0.8 M x.0 M x.0 G /8 G /8 YL 2 2 Z 7 7

25 Compact Guide Cylinder Series M, L: ø to ø 4 x YY depth YL øx H7 depth XL T-slot dimensions øxh7 X b X ±0.02 a c e d XB XH7 XC XL Detailed figure of XX section WB Z W Bottom view Section XX a.. 8. T-slot dimensions b c.. 7. d e x NN through Section XX Z W 4 x øo through 4 x øob counterbore depth OL L 4 x MM depth ML Section XX øx H7depth XL For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Stroke on page 347. M, L Common Dimensions Standard stroke T R X ±0.02 2,, 7 0, 2, 7, 0, 2 0, 3, B P PB PW Q C R 9 4 D S F FB G G GB H H J M (Slide bearing), DB, E Dimensions DB st or less Over st to 0 st Over 0 st Q S 2 2 ød ødb M M M8 M K L MM M8 x.2 M8 x.2 M x. M x ML Choice of Rc, NPT, G port is possible. (Refer to page 34.) NN M8 x.2 M8 x.2 M x. M x O OB OL Rc /8 Rc /8 Rc /4 Rc /4 T U V W WB VB 2 st or less Over 2 st Over 0 st Over 0 st to 0 st to 0 st to 0 st Over 0 st 2 st or less Over 2 st Over 0 st to 0 st to 0 st X X XB XC XL Over 0 st Over 0 st to 0 st E st or less Over st to 0 st Over 0 st G P + Stroke F FB C + Stroke B + Stroke + Stroke GB NPT /8 NPT /8 NPT /4 NPT/4 L (Ball bushing bearing), DB, E Dimensions P Nil N TF 8 8 G /8 G /8 G /4 G /4 YL Z 2 22 E DB st or less Over st Over 0 st to 0 st to 0 st Over 0 st st or less Over st Over 0 st to 0 st to 0 st Over 0 st E PW x P X U (OL) X ± x P (Plug) PB J K G H: T-slot for hexagon bolt VB V H øx YY M8 x.2 M8 x.2 M x. M x H7depth XL MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

26 Series M, L: ø, ø0 4 x YY depth YL ø H7 depth T-slot dimensions ø H7 X X ±0.02 WB Section XX 0 a T-slot dimensions b c 2 3. d 8 e 22. Z W Bottom view 4 x NN through Section XX Z W 4 x øo through 4 x øob counterbore depth 8 4 x MM depth ML Section XX (8) ødb X ±0.02 T R ød PW X U X ±0.02 H: T-slot for hexagon bolt VB V H 7 b a c d e H7 Detailed figure of section XX L ø H7depth Q S GC G P + Stroke F FB C + Stroke B + Stroke + Stroke GB E 2 x P 2 x P (Plug) JB PB J J G K ø H7 depth For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Stroke on page 347. Choice of Rc, NPT, G port is possible. (Refer to page 34.) M, L Common Dimensions Standard stroke ,, 7, 0 2,, 7, 0 2, 0, 3, B 9. P PB PW Q C. R 74 2 D 2 S 7 90 F 22 2 T FB 8 2 U 88 G G GB GC H M (Slide bearing), DB, E Dimensions 32 DB st or less Over st to 0 st Over 0 st H M2 M L (Ball bushing bearing), DB, E Dimensions 0 J 4.. J JB K 4 L MM M2 x.7 M4 x ML NN M2 x.7 M4 x O OB. 2. V W WB VB 2 st or less Over 2 st Over 0 st Over 0 st to 0 st to 0 st to 0 st Over 0 st 2 st or less Over 2 st Over 0 st to 0 st to 0 st X Over 0 st Over 0 st to 0 st E st or less Over st to 0 st Over 0 st P Nil N TF Rc 3/8 NPT 3/8 Rc 3/8 NPT 3/8 YL 28 G 3/8 G 3/8 Z 28 E DB 2 st or less Over 2 st 2 st or less Over 2 st Over st Over st to st to 0 st Over 0 st to st to 0 st Over 0 st YY M2 x.7 M4 x

27 Compact Guide Cylinder/With ir Cushion Series ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Series with air cushion type has been remodeled for a lightweight design. When selecting a product, refer to the new -Z series. MGJ -Z W MGQ MGG MGC MGF MGZ MGT Stroke Variations Bearing type M Slide bearing L Ball bushing bearing 2 0 Stroke Intermediate stroke Strokes available by the mm interval by changing the collar. 3 D- -X

28 Compact Guide Cylinder/With ir Cushion Series ø, ø, ø2, ø, ø, ø, ø, ø, ø0 How to Order Series with air cushion type has been remodeled for a lightweight design. When selecting a product, refer to the new -Z series. M M9BW Compact Guide Cylinder M L Bearing type Slide bearing Ball bushing bearing 2 mm mm 2 mm mm mm 0 mm mm mm 0 mm Thread type Nil N TF M x 0.8 Rc NPT G For bore sizes, M x 0.8 is only available. With air cushion Cylinder stroke Refer to Standard Stroke on page 3. Number of auto switches Nil S n 2 pcs. pc. n pcs. uto switch Without auto switch Nil (Built-in magnet) For the applicable auto switch model, refer to the table below. Made to Order Specification For details, refer to page 3. pplicable uto Switches/Refer to pages 839 to 07 for further information on auto switches. Type Reed auto switch Solid state auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) Magnetic field resistant (2-color indication) Electrical entry Indicator light Wiring (Output) Load voltage DC 3-wire (NPN) 3-wire (PNP) 2-wire V,2 V 2 V 3-wire (NPN) Grommet Yes 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire V V,2 V 2 V V,2 V 2 V 2-wire (Non-polar) 3-wire Yes (NPN equivalent) Grommet V No 2-wire V 2 V C 0 V 0 V or less uto switch model Perpendicular In-line M9NV M9PV M9BV M9NWV M9PWV M9BWV M9NV M9PV M9BV 9V 93V 2 90V M9N M9P M9B M9NW M9PW M9BW M9N M9P M9B P3DW P4DW Lead wire length (m) 0. (Nil) (M) 3 (L) (Z) Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Consult with SMC regarding water resistant types with the above model numbers. 2 m type lead wire is only applicable to D-93. Lead wire length symbols: 0. m Nil m M 3 m L (Example) M9NW (Example) M9NWM (Example) M9NWL Solid state auto switches marked with are produced upon receipt of order. s to 0 are available for D-P4DW. s 2 to 0 are available for D-P3DW. m Z (Example) M9NWZ Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages 90 and 9. For D-P3DW, refer to pages 948 and 949. uto switches are shipped together (not assembled). Relay, PLC Relay, PLC B 34

29 Minimum Proper Operating uto Compact Guide Cylinder With ir Cushion Series Specifications Symbol ir cushion ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Cushion Lubrication Stroke length tolerance Standard Stroke ø ø ø2 ø ø ø ø ø ø0 Double acting ir. MPa.0 MPa 0. MPa 0.2 MPa to 0 C (No freezing) to 0 mm/s to 0 mm/s ir cushion on both ends (Without bumper) Not required (Non-lube) +. 0 to, 0 Standard stroke 2,, 7, 0, 2,, 7, 0, 2 2,, 7, 0, 2,, 7, 0, 2, 0, 3, 0, 7, 0, 2,, 7, 0, 2, 0, 3, 0 Made to Order: Individual Specifications (For details, refer to pages 7 and 8.) Symbol Specifications -X44 Symmetrical port position -X87 Lateral piping type (Change of plug position) Made to Order Specifications (For details, refer to pages 09 to 22.) Symbol Specifications -XC9 Intermediate stroke (Spacer type) -XC79 Machining tapped hole, drilled hole and pin hole additionally. Refer to pages 4 to for cylinders with auto switches. auto switch mounting stroke auto switch mounting position (detection at stroke end) and mounting height range switch mounting bracket: Part no. Manufacture of Intermediate Stroke Description Part no. pplicable stroke Example Theoretical Output 2 0 Rod size Intermediate strokes by the mm interval are available by replacing collars of a standard stroke cylinder. Minimum manufacturable stroke Operating Piston area direction (mm 2) OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN ø to ø ø, ø0 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2) ø to ø: mm ø, ø0: mm Select a rubber bumper type, because the cushion effect is not obtainable for less than this stroke. Suffix -XC9 to the end of standard part number. ø to 9 to 399 to 399 Model: M-3-XC9 collar mm in width is installed in a M- C dimension is 2 mm. Note) Intermediate stroke (by the mm interval) based on an exclusive body will be available upon request for special. OUT(N) Operating pressure (MPa) IN(N) (N) MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

30 Series Weight Slide bearing: M to Model M M M2 M M M M M M0 Standard stroke (kg) Ball bushing bearing: L to 0 (kg) Model Standard stroke L L L L L L L L L llowable Rotational Torque of Plate (ir Cushion) Non-rotating ccuracy of Plate Torque: T (N m) +θ θ 2 0 Bearing type 2 M 0.3 L.27 M 0.99 L 2. M.4 L 4.08 M.3 L.9 M 7.00 L. M 3.0 L 9.7 M 4.7 L.2 M L M L Stroke T (N m) For non-rotating accuracy θ without load, use a value no more than the values in the table as a guide. 2 0 Non-rotating accuracy θ M L ±0.08 ±0. ±0.07 ±0.09 ±0.0 ±0.08 ±0.0 ±0.0 ±0.04 ±0.0 3

31 Selection Conditions Compact Guide Cylinder/With ir Cushion Series Model Selection Vertical Horizontal L L L L m m Mounting orientation m m Maximum speed (mm/s) Graph (Slide bearing type) Graph (Ball bushing bearing type) 0 or less (), (2) () to (9) Selection Example (Vertical Mounting) 0 (3), (4) () to (4) 0 or less (), () (9), () 0 (7), (8) (2), (22) Selection Example 2 (Horizontal Mounting) Selection conditions Mounting: Vertical Bearing type: Ball bushing Stroke: 7 stroke Maximum speed: 0 mm/s Load mass: 7 kg Eccentric distance: 70 mm Find the point of intersection for the load mass of 7 kg and the eccentric distance of 70 mm on graph (), based on vertical mounting, ball bushing, 7 mm stroke, and the speed of 0 mm/s. L2-7 is selected. () 7 Stroke or Less, V = 0 mm/s or less ø2 ø ø Selection conditions Mounting: Horizontal Bearing type: Slide bearing Distance between plate and load center of gravity: mm Maximum speed: 0 mm/s Load mass: 8 kg Stroke: 0 stroke Find the point of intersection for the load mass of 8 kg and 0 stroke on graph (7), based on horizontal mounting, slide bearing, the distance of mm between the plate and load center of gravity, and the speed of 0 mm/s. M-0 is selected. (7) L = mm, V = 0 mm/s ø, ø ø ø2 ø ø ø0 ø ø, ø ø ø2 ø ø MGJ -Z W MGQ MGG MGC MGF MGZ MGT Eccentric distance L Stroke. When the maximum speed exceeds 0 mm/s, the allowable load mass is determined by multiplying the value shown in the graph at 0 mm/s by the coefficient listed in the table below. Maximum Up to 0 mm/s Up to 0 mm/s Up to 0 mm/s Coefficient Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more. 37 D- -X

32 Series Vertical Mounting (Slide Bearing) Operating pressure 0.4 MPa Operating pressure 0. MPa or more M to 0 () 2 Stroke, V = 0 mm/s or less (2) Over 2 Stroke, V = 0 mm/s or less ø0 0 ø0 0 ø 0 ø ø ø ø ø ø ø ø ø2 ø ø ø2 ø ø ø Eccentric distance L Eccentric distance L (3) 2 Stroke, V = 0 mm/s (4) Over 2 Stroke, V = 0 mm/s 0 0 ø0 ø0 0 0 ø ø 0 0 ø ø ø ø ø ø ø2 ø ø ø ø2 ø ø ø Eccentric distance L Eccentric distance L. Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more. 38

33 Model Selection Series Vertical Mounting (Ball Bushing) Operating pressure 0.4 MPa Operating pressure 0. MPa or more L to 2 () 7 Stroke or Less, V = 0 mm/s or less () Over 7 Stroke, V = 0 mm/s or less ø2 ø2 ø ø ø ø 0 0 Eccentric distance L 0 0 Eccentric distance L L to (7) 2 Stroke, V = 0 mm/s or less (8) Over 2 Stroke, V = 0 mm/s or less 0 ø ø ø ø 0 0 L, 0 (7) V = 0 mm/s or less Eccentric distance L 0 ø ø ø ø 0 0 Eccentric distance L MGJ -Z W MGQ MGG MGC MGF MGZ MGT 0 ø0 0 ø 0 0 Eccentric distance L. Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more. 39 D- -X

34 Series Vertical Mounting (Ball Bushing) Operating pressure 0.4 MPa L to 2 () 7 Stroke or Less, V = 0 mm/s () Over 7 Stroke, V = 0 mm/s ø2 ø2 ø ø ø 0 0 ø 0 0 Eccentric distance L Eccentric distance L L to (2) 2 Stroke, V = 0 mm/s (3) Over 2 Stroke, V = 0 mm/s ø ø ø ø ø ø ø ø 0 0 Eccentric distance L 0 0 Eccentric distance L L, 0 (4) V = 0 mm/s 0 0 ø0 ø 0 0 Eccentric distance L. Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more. 370

35 Model Selection Series Horizontal Mounting (Slide Bearing) M to 0 () L = mm, V = 0 mm/s or less () L = 0 mm, V = 0 mm/s or less ø, ø, ø2 ø ø ø0 ø ø, ø, ø2 ø ø ø0 ø ø, ø, ø, ø, ø2 ø ø2 ø ø ø ø, ø ø ø2 ø ø Stroke ø0 ø ø, ø ø ø2 ø ø ø, ø, ø2 ø ø Stroke (7) L = mm, V = 0 mm/s (8) L = 0 mm, V = 0 mm/s ø0 ø ø, ø ø ø2 ø ø MGJ -Z W MGQ MGG MGC MGF MGZ MGT Stroke Stroke 37 D- -X

36 Series Horizontal Mounting (Ball Bushing) (9) L = mm, V = 0 mm/s or less () L = 0 mm, V = 0 mm/s or less L to 2 L to 2 ø2 ø ø ø2 ø ø ø2 ø ø ø2 ø ø Stroke Stroke L to L to ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, Stroke Stroke L, 0 L, 0 ø0 ø ø0 ø 0 0 Stroke 0 0 Stroke 372

37 Model Selection Series Horizontal Mounting (Ball Bushing) (2) L = mm, V = 0 mm/s (22) L = 0 mm, V = 0 mm/s L to 2 L to 2 ø2 ø2 ø2 ø2 ø ø ø ø ø ø ø ø Stroke Stroke L to L to ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, Stroke Stroke L, 0 L, 0 ø0 MGJ -Z W MGQ MGG MGC MGF MGZ MGT ø ø0 ø 0 0 Stroke 0 0 Stroke 373 D- -X

38 Series Operating Range when Used as Stopper ø to 2/M to 2 (Slide bearing) M to 2 (Slide bearing) L mm υ m L mm When selecting a model with a longer L dimension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Note ) When using as a stopper, select a model with 2 stroke or less. Note 2) Model L (Ball bushing bearing) cannot be used as a stopper. υ m Mass of transferred object: m (kg) ø2 ø ø Transfer speed: υ (m/min) Bore Size ø to 0/M to 0 (Slide bearing) M to 0 (Slide bearing) L mm m υ L mm When selecting a model with a longer L dimension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Note ) When using as a stopper, select a model with stroke or less. Note 2) Model L (Ball bushing bearing) cannot be used as a stopper. m υ Mass of transferred object: m (kg) ø0 ø ø ø ø ø Transfer speed: υ (m/min) 374

39 Compact Guide Cylinder With ir Cushion Series Series M/Construction (With air cushion) M to 2 M to 0!0 i! u e!!3 #0! #! i! w w o @3!4 Component Parts No. Description Material Note Body 2 Piston 3 Piston rod 4 Collar Bushing Head cover Guide rod Plate Plate mounting bolt Guide bolt Retaining ring Retaining ring Magnet Plug Hexagon socket head cap plug Slide Bearing Felt Holder Ball bushing Spacer ø: 2 stroke ø: stroke or more ø, ø2: stroke or more luminum alloy luminum alloy Stainless steel Carbon steel luminum alloy Bearing alloy luminum alloy Carbon steel Carbon steel Carbon steel Carbon steel Carbon tool steel Carbon tool steel Carbon steel Bearing alloy Felt Resin luminum alloy Cushion valve section ø to ø2 ø to ø0 ø to ø ø, ø0 ø to ø2 ø to ø0 Hard anodized Chromated Hard chrome plated Clear anodized Painted Clear anodized Painted Hard chrome plated Nickel plated Nickel plated Nickel plated Phosphate coated Phosphate coated ø ø to ø0 Nickel plated ø or more Component Parts No. Description Material Note Wear ring Resin 2 Cushion valve Steel 22 Gasket NBR 23 Retaining ring Carbon tool steel Except ø Steel ball Carbon steel ø to ø 2 Plug Carbon steel ø to ø0 Nickel plated 2 Piston seal NBR 27 Rod seal NBR 28 Cushion seal Urethane 29 Gasket NBR Gasket B NBR 3 Gasket C NBR Replacement Parts: Seal Kit Kit no. --PS --PS 2--PS --PS --PS Contents Set of #0, # 0 Cushion valve section t ø or more Kit no. --PS --PS --PS 0--PS * Seal kit to #. Order the seal kit, based on each bore size. * Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S-0 @2 Contents Set of #0, # 37 MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

40 Series Series L/Construction (With ir Cushion) L to 2 L to 0!2!8!2!8 ø or more ø,ø2: 7 stroke or less ø,ø2: 0 stroke or more!9 ø or more ø to ø: 0 stroke or more!9 37

41 Compact Guide Cylinder With ir Cushion Series M, L (With ir Cushion): ø to ø2 4 x YY depth YL øx H7 depth T-slot dimensions b XB øx H7 a X H7 3 X X ± c d e a T-slot dimensions b c d e Detailed figure of section XX Z WB W Section XX Bottom view 3 4 x NN through Section XX Z W 2 x cushion valve (Width across flats CV) 4 x øo through 4 x øob counterbore depth OL ø L 4 x MM depth ML Section XX MGJ (OL) -Z T R X ±0.02 ød ødb PW X U X ±0.02 X H: T-slot for hexagon bolt VB V H W MGQ øx H7 depth Q S G F FB P + Stroke C + Stroke B + Stroke + Stroke GB E 2 x P 2 x P (Plug) PB J G K øx H7 depth MGG MGC MGF MGZ MGT Note ) For the intermediate strokes, refer to Manufacture of Intermediate Stroke on page 3. Note 2) When adjusting the ø cushion valve, use a 3 mm flat head watchmakers screwdriver. M, L Common Dimensions 2 2 Standard stroke 2,, 7, 0, 2,, 7, 0, 2 2,, 7, 0, 2,, 7 0, 2, 0, 3, 0 P PB PW Q B C CV D F FB G G GB H H J R S T U V VB 7 st or less to 7 st W M4 M M 0, 2 st st or more 0 0 K 8 2 L 22 7 st or less MM M x 0.8 M x 0.8 M x.0 0 to 7 st WB For bore size wlth ø, M x 0.8 is only available. Rc, NPT, G port can be selected for bore sizes with ø or more. (Refer to page 34.) ML 2 3 0, 2 st 7 7 NN M x 0.8 M x 0.8 M x.0 0 st or more 7 7 O OB OL X X XB P Nil N TF M x 0.8 Rc /8 NPT /8 Rc /8 NPT /8 YY M x 0.8 M x.0 M x.0 YL 2 2 G /8 G /8 Z 7 7 M (Slide bearing), DB, E Dimensions 2 2 st st ,0 st DB 2 to 0 st 2 st or more st st E 7,0 st to 0 st 2 st or more L (Ball bushing bearing), DB, E Dimensions 2 2 st 9 0., 7 st st DB 2 to 0 st 2 st or more st , 7st E 0st to 0st 2 st or more D- -X

42 Series M, L (With ir Cushion): ø to ø 4 x YY depth YL øx H7 depth XL T-slot dimensions XB øx H7 X XL Detailed figure of section XX WB Z W X ±0.02 Section XX a.. 8. T-slot dimensions b c.. 7. d e x NN through Section XX Z 2 x cushion valve (Width across flats CV) 4 x øo through W 4 x øob counterbore depth OL L 4 x MM depth ML Section XX (OL) ødb X ±0.02 T R ød PW X U X ±0.02 H: T-slot for hexagon bolt VB V H b a X H7 XC c d e Bottom view øx H7 depth XL Q S F FB G P + Stroke C + Stroke B + Stroke + Stroke GB E 2 x P 2 x P (Plug) PB J G K øx H7 depth XL For the intermediate strokes, refer to Manufacture of Intermediate Stroke on page 3. Rc, NPT and G ports can be selected. (Refer to page 34.) M, L Common Dimensions M (Slide bearing), DB, E Dimensions 378 Standard stroke 2,, 7, 0 2,, 7 0, 2, 0 3, 0 P PB PW Q st st DB 7 to 0 st 2 st or more B C CV D F FB G G GB H H J R S T st U V VB 7 st or less st E 7 to 0 st 2 st or more to 7 st 28 W , 2 st M M M8 M 0 st or more K st or less L to 7 st MM M8 x.2 M8 x.2 M x. M x. 0, 2 st 2 22 ML st or more NN M8 x.2 M8 x.2 M x. M x. X 42 X 4 4 O OB OL XB XC XL 8 8 P Nil N TF Rc /8 Rc /8 Rc /4 Rc /4 YY M8 x.2 M8 x.2 M x. M x. L (Ball bushing bearing), DB, E Dimensions 2st st st WB 0st DB 2 to 0 st 2 st or more NPT /8 NPT /8 NPT /4 NPT /4 YL G /8 G /8 G /4 G /4 Z 2 22 E 2st st 7st 0st 2 to 0 st 2 st or more

43 Compact Guide Cylinder With ir Cushion Series M, L (With ir Cushion): ø, ø0 4 x YY depth YL ø H7 depth T-slot dimensions X X ±0.02 H7 7 ø H7 0 a T-slot dimensions b c 2 3. d 8 e 22. Detailed figure of section XX WB Z W Section XX 4 x NN through Section XX T R X ±0.02 ød Z W 4 x øo through 4 x øob counterbore depth 8 2 x cushion valve (Width across flats 4) PW b a c e d Bottom view X U X ±0.02 (8) L 4 x MM depth ML H: T-slot for hexagon bolt Section XX VB V H MGJ -Z W MGQ MGG MGC ødb MGF ø H7 depth Q S GC F FB G P + Stroke C + Stroke B + Stroke + Stroke GB E 2 x P 2 x P (Plug) JB PB J J G K ø H7 depth MGZ MGT For the intermediate strokes, refer to Manufacture of Intermediate Stroke on page 3. M, L Common Dimensions 0 0 Standard stroke B,7,0,2,7,0,2 0,3, P PB PW Q C 8. 9 R 74 2 D 2 S 7 90 F FB G G GB GC H H J 22 2 T U V VB, 7 st M2 M4 0 to 7 st W 4.. 0, 2 st 0 2 J 38 4 JB st or more 0 3 K 4 L 4 2 Rc, NPT and G ports can be selected. (Refer to page 34.) MM M2 x.7 M4 x 2.0, 7 st 0 to 7 st ML 2 3 WB NN M2 x.7 M4 x 2.0 0, 2 st 28 2 O OB st or more X 0 P Nil N TF Rc 3/8 NPT 3/8 G 3/8 Rc 3/8 NPT 3/8 G 3/8 YY M2 x.7 M4 x 2.0 YL 28 Z 28 M (Slide bearing), DB, E Dimensions 0 st to 0 st st or more 93 3 DB 3 E st 7 to 0 st 2 st or more L (Ball bushing bearing), DB, E Dimensions 0 st to 0 st 0 2 st or more 93 3 DB 2 E st 7 to 0 st 2 st or more D- -X

44 Compact Guide Cylinder/With End Lock Series ø, ø2, ø, ø, ø, ø, ø, ø0 Stroke Variations Bearing type Stroke Intermediate stroke Locking direction Manual release M Slide bearing L Ball bushing bearing 2 0 Spacer installation type vailable by the mm interval. Rod end lock Head end lock Non-lock type Lock type 3

45 Compact Guide Cylinder/With End Lock Series ø, ø2, ø, ø, ø, ø, ø, ø0 Compact Guide Cylinder M L M Bearing type Slide bearing Ball bushing bearing 2 0 mm 2 mm mm mm mm mm mm 0 mm Thread type Nil Rc N NPT TF G Cylinder stroke Refer to Standard Stroke on page 382. How to Order 0 H N M9BW Manual release type N Non-lock type L Lock type Lock position H Head end lock R Rod end lock pplicable uto Switches/Refer to pages 893 to 07 for further information on auto switches. Type Reed auto switch Solid state auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) Magnetic field resistant (2-color indication) Electrical entry Indicator light Wiring (Output) Load voltage DC 3-wire (NPN) 3-wire (PNP) 2-wire V,2 V 2 V 3-wire (NPN) Grommet Yes 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire V V,2 V 2 V V,2 V 2 V 2-wire (Non-polar) 3-wire (NPN equivalent) Grommet Yes V No 2-wire V 2 V C 0 V 0 V or less uto switch model Perpendicular In-line M9NV M9PV M9BV M9NWV M9PWV M9BWV M9NV M9PV M9BV 9V 93V 2 90V M9N M9P M9B M9NW M9PW M9BW M9N M9P M9B P3DW P4DW Made to Order Specification For details, refer to page 382. Number of auto switches Nil S n 2 pcs. pc. n pcs. uto switch Without auto switch Nil (Built-in magnet) For the applicable auto switch model, refer to the table below. Lead wire length (m) 0. (Nil) (M) (Z) Pre-wired connector Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Consult with SMC regarding water resistant types with the above model numbers. 2 m type lead wire is only applicable to D-93. Lead wire length symbols: 0. m Nil (Example) M9NW m M (Example) M9NWM 3 m L (Example) M9NWL m Z (Example) M9NWZ pplicable load Solid state auto switches marked with are produced upon receipt of order. s to 0 are available for D-P4DW. s 2 to 0 are available for D-P3DW. Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages 90 and 9. For D-P3DW, refer to the WEB catalog. uto switches are shipped together (not assembled). 3 (L) IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PLC Relay, PLC 38 MGJ -Z B W MGQ MGG MGC MGF MGZ MGT D- -X

46 Minimum Proper Operating uto Series Specifications Symbol Rubber bumper Symbol Specifications -X87 Lateral piping type (Change of plug position) Made to Order Specifications (For details, refer to pages 09 to 22.) Symbol Specifications -XC79 Machining tapped hole, drilled hole and pin hole additionally. Refer to pages 4 to for cylinders with auto switches. auto switch mounting stroke auto switch mounting position (detection at stroke end) and mounting height range switch mounting bracket: Part no. 382 Made to Order: Individual Specifications (For details, refer to page 8.) ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Cushion Lubrication Stroke length tolerance 0. MPa except the lock unit. Lock Specifications Lock position Holding force (Max.) N Backlash Manual release Standard Stroke, 2,,,,,, 0 Theoretical Output Rod size ø 2 ø2 3 Operating Piston area direction (mm 2) ø ø2 ø ø ø ø ø ø0 Double acting ir. MPa.0 MPa 0. MPa to 0 C (No freezing) to 0 mm/s to 0 mm/s Rubber bumper on both ends Not required (Non-lube) +. 0 mm ø mm or less Non-lock type, Lock type djust switch positions for operation at both the stroke end and backlash (2 mm) movement positions. Standard stroke 2,, 7, 0, 2,, 7, 0, 2, 0, 3, 0 Manufacture of Intermediate Stroke Description Head end, Rod end ø ø ø OUT 2 Operating pressure (MPa) OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2) ø 34 IN ø0 390 Spacer installation type. Dealing with the stroke by the mm interval is available by installing spacer with standard stroke cylinder. When a spacer is mounted on the cylinder with an end lock on the rod side, use a special piston rod. Part no. Refer to How to Order for the standard model numbers on page 38. pplicable stroke to 39 Example Part no.: M-3-HN spacer mm in width is installed in a M--HN. C dimension is 9 mm. Note ) The minimum stroke for mounting auto switches is stroke or more for two switches, and stroke or more for one switch. Note 2) Intermediate stroke (by the mm interval) based on an exclusive body will be available upon request for special. (N)

47 Compact Guide Cylinder With End Lock Series Weight Slide Bearing: M to 0 (Basic weight) (kg) Model Standard stroke M M2 M M M M M M Ball Bushing Bearing: L to 0 (Basic weight) 2 0 llowable Rotational Torque of Plate 2 0 Bearing type M L M L M L M L M L M L M L M L Model L L2 L L L L L L Lock Unit dditional Weight 2 Head end lock HN HL Torque: T (N m) Rod end lock RN RL Standard stroke Head end lock HN HL RN Calculation: (Example) M-0-HN Basic Weight + Lock unit additional weight =.98 kg T (N. m) Stroke Model selection is the same as /standard type. Refer to pages 349 to (kg) Rod end lock RL Non-rotating ccuracy of Plate θ θ Non-rotating accuracy θ M L ±0.07 ±0.09 ±0.0 ±0.08 ±0.0 ±0.0 ±0.04 ±0.0 (kg) For non-rotating accuracy θ without load, use a value no more than the values in the table as a guide. 383 MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

48 Series Construction/Series e!!7 u w!4 i r y ø, ø, ø, ø, ø0 ø, ø2: 2 stroke ø or more # ø or more ø, ø Non-locking type (Head end lock) #9 #7 #4 $4 $ ø to ø #2 # ø, ø0 #3 $ (Rod end lock) ø to ø t ø, ø0 Component Parts No. Description Material Note Body luminum alloy 2 Piston luminum alloy 3 Piston rod Collar Bushing Head cover Guide rod Plate Plate mounting bolt Guide bolt Retaining ring Retaining ring Bumper Bumper B Magnet Hexagon socket head cap plug Slide Bearing Felt Holder Ball bushing Spacer Steel ball Plug Piston seal 2 Rod seal 2 Gasket 27 Gasket B Stainless steel ø, ø2 Carbon steel ø to ø0 luminum alloy Bearing alloy luminum alloy Carbon steel Carbon steel Carbon steel Carbon steel Carbon tool steel Carbon tool steel Urethane Urethane Carbon steel Bearing alloy Felt Resin luminum alloy Carbon steel Carbon steel NBR NBR NBR NBR Hard anodized Chromated Hard chrome plated with rod end lock only Hard chrome plated Chromated Chromated Hard chrome plated Nickel plated Nickel plated Nickel plated Phosphate coated Phosphate coated ø to ø ø to ø0 Nickel plated Nickel plated Component Parts No. Description Material Note Piston gasket Lock bolt Lock holder Lock piston Lock spring Seal retainer 34 Bumper 3 Hexagon socket head cap screw 3 Hexagon socket head cap screw 37 Cap 38 Cap B 39 Rubber cap M/O knob 4 M/O bolt 42 M/O spring 43 Stopper ring 44 Lock piston seal 4 Lock holder gasket NBR Carbon steel Brass Carbon steel Stainless steel Carbon steel Urethane Carbon steel Carbon steel luminum die-casted Carbon steel Synthetic rubber Zinc die-casted lloy steel Steel wire Carbon steel NBR NBR Replacement Parts/Seal Kit 2 Kit no. Contents -B-PS Set of nos. 2-B-PS #, $4, $ -B-PS 0 ø to ø0 only Zinc chromated Electroless nickel plated Hard chrome plated Zinc chromated (ø, ø0 only) Black zinc chromated Zinc chromated (ø, ø only) Black painted SQ treated Kit no. -B-PS -B-PS -B-PS 0-B-PS Black painted Black zinc chromated chromated chromated Set of nos. above Set of nos. #, #, $4, $ Each seal kit includes the parts listed above. Order the seal kit based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S-0 ( g) 384

49 Compact Guide Cylinder With End Lock Series Construction/Series ø, ø, ø, ø, ø0 ø or more ø or more ø to : Over 0 Lock type $0 #8 $ $2 $3 MGJ -Z W MGQ MGG MGC MGF MGZ MGT 38 D- -X

50 Series Dimensions: ø, ø2 4 x NN through 4 x ø.4 through 4 x MM depth ML 4 x M x.0 depth 2 Section XX 7 W 4 x ø9. counterbore depth. L Section XX Section XX (.) X ±0.02 T R ød PW X U X ±0.02 ø M:T-slot for hexagon bolt VB V H X ±0.02 X Q S øx H7 depth G DL Stroke GB C + Stroke B + Stroke + Stroke 2 x P øx H7 depth 2 x P øx H7 depth (Plug) With rod end lock.4 ødb E HR PB J K G End lock mechanism Manual release Non-lock type WB W 7 XB øx H7 ø e d X H7 3 Detailed figure of section XX DM With head end lock ø2 HN End lock mechanism (Manual release lock type) T-slot dimensions T-slot dimensions d e For intermediate strokes other than standard strokes, refer to the Manufacture of Intermediate Stroke on page 382. M, L Common Dimensions 2 2 Standard stroke 2,, 7, 0, 2, 7, 0, 2 0, 3, 0 T U V VB 7 st or less B C D G G GB H J K L MM ML Over 7 st to 7 st 3 42 W.. Over 7 st to 2 st Over 2 st 0 0 M (Slide bearing), DB, E Dimensions 2 2 st or less End Lock Mechanism Dimensions 2 DL st or less M x 0.8 M x.0 WB Over 7 st Over 7 st Over to 7 st to 2 st 2 st M x 0.8 M x.0 X X XB NN Rc /8 Rc /8 P N L (Ball bushing bearing), DB, E Dimensions Nil TF NPT /8 G /8 NPT /8 G /8 PB. 3. PW Q R S E E Over 2 st DB Over 2 st Over 7 st DB Over 7 st to 7 st Over 7 st 2 st or less to 7 st Over 7 st 7 st or less to 7 st Over 7 st 7 st or less to 7 st Over 7 st DM 9 HR. 8 HN Rc, NPT and G ports can be selected. (Refer to page 38.)

51 Compact Guide Cylinder With End Lock Series Dimensions: ø to ø 4 x NN through Section XX Z W 4 x øo through 4 x øob counterbore depth OL L 4 x MM depth ML Section XX 4 x YY depth YL Section XX (OL) T R X ±0.02 ød DL PW X U X ±0.02 ø H: T-slot for hexagon bolt VB V H X ±0.02 X øx H7 depth XL Q S ødb G LL P + Stroke FFB C + Stroke B + Stroke + Stroke GB E 2 x P HR End lock mechanism Manual release Non-lock type PB J K G øx H7 depth XL 2 x P (Plug) WB W Z øx H7 depth XL With rod end lock b a For intermediate strokes other than standard strokes, refer to the Manufacture of Intermediate Stroke on page 382. M, L Common Dimensions X H7 XC XL Detailed figure of section XX Standard stroke P B C D F FB G G GB H H J K L MM ML NN O OB OL Nil N TF M 34 M8 x.2 M8 x Rc/8 NPT/8 G/8 2,, 7 0, 2, M M8 x.2 M8 x Rc/8 NPT/8 G/8 7, 0, M8 4 M x. 22 M x Rc/4 NPT/4 G/4 0, 3, M M x. 22 M x Rc/4 NPT/4 G/4 W WB P PB PW Q R S T U V VB 7 st Over 7 st Over 7 st Over 7 st Over 7 st Over 7 st Over X X XB XC XL YY YL Z or less to 7 st to 2 st 2 st or less to 7 st to 2 st 2 st XB øx H With head end lock LL DM HN End lock mechanism (Manual release lock type) ømo Rc, NPT and G ports can be selected. (Refer to page 38.) T-slot dimensions T-slot dimensions a b c e d c.. 7. M8 x.2 M8 x.2 M x. M x. d e MGJ -Z W MGQ MGG MGC MGF MGZ MGT M (Slide bearing), DB, E Dimensions 2 st or less Over 2 st to 7 st Over 7 st DB 2 st or less End Lock Mechanism Dimensions DL DM HR HN LL E Over 2 st to 7 st 7. 2 MO Over 7 st L (Ball bushing bearing), DB, E Dimensions 2 st or less Over 2 st to 7 st Over 7 st to 7 st Over 7 st DB 2 st or less Over 2 st to 7 st E Over 7 st to 7 st Over 7 st D- -X

52 Series Dimensions: ø, ø0 Section XX 4 x NN through Z W 4 x øo through 4 x øob counterbore depth 8 HR L 4 x MM depth ML 4 x YY depth YL Section XX Section XX (8) ø H7 depth 2 x P End lock mechanism Manual release Non-lock type ø H7 depth 2 x P (Plug) WB W Z ø H7 depth With rod end lock HN b a ødb T R X ±0.02 ød PW X U X ±0.02 ø2 H: T-slot for hexagon bolt VB V H X ±0.02 X Q S GC G DL P + Stroke F FB C + Stroke B + Stroke + Stroke GB E JB PB J J K G 7 ø H7 DM ø23 c d e H7 Detailed figure of section XX With head end lock End lock mechanism (Manual release lock type) T-slot dimensions T-slot dimensions 0 a b c 2 3. d 8 e 22. For intermediate strokes other than standard strokes, refer to the Manufacture of Intermediate Stroke on page 382. M, L Common Dimensions 0 0 Standard stroke 2,, 7, 0, 2, 7, 0, 2 0, 3, 0 Nil Rc3/8 Rc3/8 P N NPT3/8 G3/8 NPT3/8 G3/8 B C D F FB G G GB GC H H J J JB K L MM ML NN O OB TF P PB PW Q R S T U V VB M2 2 M4 st or less 2 72 Over st to st W Over st to 2 st Over 2 st 0 3 Rc, NPT and G ports can be selected. (Refer to page 38.) 4 st or less Over st to st 92 8 M2 x.7 M4 x 2.0 WB Over st to 2 st 28 2 Over 2 st M2 x.7 M4 x X YY YL 0 M2 x.7 M4 x Z 28 M (Slide bearing), DB, E Dimensions 0 E DB st or less Over st st or less Over st L (Ball bushing bearing), DB, E Dimensions 0 E DB st or less Over st st or less Over st End Lock Mechanism Dimensions DL DM. 43. HR 2. HN 38. 4

53 Series With End Lock Specific Product Precautions Be sure to read before handling. Refer to front matter 39 for Safety Instructions and pages 3 to 2 for ctuator and uto Switch Precautions. Use the Recommended Pneumatic Circuit Caution This is necessary for the correct locking and unlocking actions. W Head end lock W Rod end lock Operating Precautions Caution. Do not use 3 position solenoid valves. void use in combination with 3 position solenoid valves (especially closed center metal seal types). If pressure is trapped in the port on the lock mechanism side, the cylinder cannot be locked. Furthermore, even after being locked, the lock may be released after some time, due to air leaking from the solenoid valve and entering the cylinder. 2. Back pressure is required when releasing the lock. Before starting operation, be sure to control the system so that air is supplied to the side without the lock mechanism as shown in the figure above. There is a possibility that the lock may not be released. (Refer to the section on releasing the lock.) 3. Release the lock when mounting or adjusting the cylinder. If mounting or other work is performed when the cylinder is locked, the lock unit may be damaged. 4. Operate with a load ratio of % or less. If the load ratio exceeds %, this may cause problems such as failure of the lock to release, or damage to the lock unit.. Do not operate multiple cylinders in synchronization. void applications in which two or more end lock cylinders are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required.. Use a speed controller with meter-out control. Lock cannot be released occasionally by meter-in control. 7. Be sure to operate completely to the cylinder stroke end on the side with the lock. If the cylinder piston does not reach the end of the stroke, locking and unlocking may not be possible. 8. Do not use an air cylinder as an air-hydro cylinder. This will cause leakage of hydraulic fluid. 9. djust an auto switch's position so that it operates for movement to both the stroke and backlash (2 mm) positions. When a 2-color indication auto switch is adjusted for green indication at the stroke end, it may change to red for the backlash return, but this is not abnormal. Operating Pressure Caution. Supply air pressure of 0. MPa or higher to the port on the side that has the lock mechanism, as it is necessary for disengaging the lock. Caution Exhaust Speed. When the pressure on the side with the lock mechanism drops to 0.0 MPa or below, the lock engages automatically. If the piping on the side with the lock mechanism is thin and long, or if the speed controller is away from the cylinder port, the lock engagement may take some due to decline of the exhaust speed. The same result will be caused by clogging of the silencer installed at the EXH port of the solenoid valve. Releasing the Lock Warning. Before releasing the lock, be sure to supply air to the side without the lock mechanism, so that there is no load applied to the lock mechanism when it is released. (Refer to the Recommended pneumatic circuits.) If the lock is released when the port on the other side is in an exhaust state, and with a load applied to the lock unit, the lock unit may be subjected to an excessive force and be damaged. lso, it is very dangerous because the piston rod will be rushed to move. Caution Manual Release. Manual release (Non-lock type) Insert the accessory bolt from the top of the rubber cap (it is not necessary to remove the rubber cap), and after screwing it into the lock piston, pull it to release the lock. If you stop pulling the bolt, the lock will return to an operational state. Thread sizes, pulling forces and strokes are as shown below. Thread size Pulling force Stroke, 2,,,, 0 M2. x 0.4 x 2 L or more M3 x 0. x L or more M x 0.8 x L or more 4.9 N N. N Remove the bolt for normal operation. It can cause lock malfunction or faulty release. 2. Manual release, Lock type While pushing the M/O knob, turn it 90 counterclockwise. The lock is released (and remains in a released state) by aligning the mark on the cap with the OFF mark on the M/O knob. When locking is desired, turn M/O button clockwise 90 while pushing fully, correspond on cap and ON mark on Release Lock M/O button. The correct position is confirmed by a click sound click. If not confirmed, locking is not done. Locked condition Released condition 389 MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

54 Compact Guide Cylinder/Heavy Duty Guide Rod Type Series S ø, ø Stroke Variations Bearing type S Slide bearing Stroke

55 Compact Guide Cylinder/ Heavy Duty Guide Rod Type Series S ø, ø How to Order S M9BW Compact Guide Cylinder Heavy duty guide rod type Made to Order Specification For details, refer to page 392. mm mm Thread type Nil Rc N NPT TF G Cylinder stroke Refer to Standard Stroke on page 392. pplicable uto Switches/Refer to pages 893 to 07 for further information on auto switches. Type Special function Electrical entry Indicator light Wiring (Output) Load voltage DC Number of auto switches Nil S n 2 pcs. pc. n pcs. uto switch Without auto switch Nil (Built-in magnet) For the applicable auto switch model, refer to the table below. Pre-wired connector pplicable load 3-wire (NPN) M9NV M9N IC V,2 V 3-wire (PNP) M9PV M9P circuit 2-wire 2 V M9BV M9B 3-wire (NPN) M9NWV M9NW IC Diagnostic indication V,2 V 3-wire (PNP) M9PWV M9PW circuit (2-color indication) Relay, Grommet Yes 2-wire V 2 V M9BWV M9BW 3-wire (NPN) M9NV M9N PLC IC Water resistant V,2 V 3-wire (PNP) M9PV M9P circuit (2-color indication) 2 V M9BV M9B 2-wire Magnetic field resistant P3DW (Non-polar) (2-color indication) P4DW 3-wire IC V 9V 9 (NPN equivalent) Yes circuit Grommet 0 V 93V 2 93 Relay, 2-wire V 2 V No 0 V or less 90V 90 IC circuit PLC Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Consult with SMC regarding water resistant types with the above model numbers. 2 m type lead wire is only applicable to D-93. Lead wire length symbols: 0. m Nil (Example) M9NW Solid state auto switches marked with are produced upon receipt of order. m M (Example) M9NWM 3 m L (Example) M9NWL m Z (Example) M9NWZ Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages 90 and 9. For D-P3DW, refer to the WEB catalog. uto switches are shipped together (not assembled). Reed auto switch Solid state auto switch C uto switch model Perpendicular In-line Lead wire length (m) 0. (Nil) (M) 3 (L) (Z) MGJ -Z W MGQ MGG MGC MGF MGZ MGT 39 D- -X B

56 Minimum Proper Operating uto Series S Specifications Symbol Rubber bumper ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Cushion Lubrication Stroke length tolerance Standard Stroke ø ø Double acting ir. MPa.0 MPa 0. MPa to 0 C (No freezing) to 0 mm/s Rubber bumper on both ends Not required (Non-lube) +. 0 mm Symbol Made to Order: Individual Specifications (For details, refer to page 8.) Specifications -X87 Lateral piping type (Change of plug position) Refer to pages 4 to for cylinders with auto switches. auto switch mounting stroke auto switch mounting position (detection at stroke end) and mounting height range switch mounting bracket: Part no., Manufacture of Intermediate Stroke Description Part no. pplicable stroke Example Theoretical Output Standard stroke 2,, 7, 0, 2,, 7, 0 Spacer installation type Spacers are installed in the standard stroke cylinder. vailable by the mm stroke interval. Refer to How to Order for the standard model numbers on page 39. to 9 Part no.: S-3 spacer mm in width is installed in a S-. C dimension is 94 mm. Note) Intermediate stroke (by the mm interval) based on an exclusive body will be available upon request for special. OUT IN Rod size Operating Piston area Operating pressure (MPa) direction (mm 2 ) OUT IN OUT IN Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2) Weight Model 2 S S Standard stroke (N) (kg) llowable Rotational Torque of Plate Non-rotating ccuracy of Plate Torque: T (N m) T (N.m) +θ θ For non-rotating accuracy θ without load, use a value no more than the values in the table as a guide. Model S S Standard stroke Model S S Non-rotating accuracy θ ±0.0 ±

57 Selection Conditions Series S Model Selection L Vertical L L Horizontal m m L Mounting orientation m m Maximum speed (mm/s) Graph (Slide bearing type) 0 or less (), (2) Selection Example (Vertical Mounting) 0 (3), (4) 0 or less (), () 0 (7), (8) Selection Example 2 (Horizontal Mounting) Selection conditions Mounting: Vertical Stroke: stroke Maximum speed: 0 mm/s Load mass: 0 kg Eccentric distance: 0 mm Find the point of intersection for the load mass of 0 kg and the eccentric distance of 0 mm on graph, based on vertical mounting, mm stroke, and the speed of 0 mm/s. S- is selected. () stroke or less, V = 0 mm/s or less () L = mm, V = 0 mm/s or less 0 0 ø ø Selection conditions Mounting: Horizontal Distance between plate and load center of gravity: mm Maximum speed: 0 mm/s Load mass: kg Stroke: 0 stroke Find the point of intersection for the load mass of kg and 0 stroke on graph, based on horizontal mounting, the distance of mm between the plate and load center of gravity, and the speed of 0 mm/s. S-0 is selected. 0 ø ø MGJ -Z W MGQ MGG MGC MGF MGZ MGT ø ø Eccentric distance L Stroke. When the maximum speed exceeds 0 mm/s, the allowable load mass is determined by multiplying the value shown in the graph at 0 mm/s by the coefficient listed in the table below. Maximum Up to 0 mm/s Up to 0 mm/s Up to 0 mm/s Coefficient Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more. 393 D- -X

58 Series S Vertical Mounting (Slide Bearing) Operating pressure 0.4 MPa Operating pressure 0. MPa or more S, () Stroke or Less, V = 0 mm/s or less (2) Over Stroke, V = 0 mm/s or less ø ø 0 0 ø ø Eccentric distance L Eccentric distance L (3) Stroke or Less, V = 0 mm/s (4) Over Stroke, V = 0 mm/s ø ø 0 0 ø ø Eccentric distance L Eccentric distance L. Use the Guide Cylinder Selection Software, when the eccentric distance is 0 mm or more. 394

59 Model Selection Series S Horizontal Mounting (Slide Bearing) S, () L = mm, V = 0 mm/s or less () L = 0 mm, V = 0 mm/s or less 0 0 ø ø ø ø ø ø ø 0 0 Stroke ø 0 0 Stroke (7) L = mm, V = 0 mm/s (8) L = 0 mm, V = 0 mm/s MGJ -Z W MGQ MGG ø ø ø ø MGC MGF MGZ MGT ø ø ø ø 0 0 Stroke 0 0 Stroke 39 D- -X

60 Series S Operating Range when Used as Stopper L mm υ m L mm υ m S Mass of transferred object: m (kg) S 0 When selecting a model with a longer L dimension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Note) When using as a stopper, select a model with stroke or less. Transfer speed: υ (m/min) 39

61 Compact Guide Cylinder Heavy Duty Guide Rod Type Series S Construction! o i!0!8 r! t!9!2!e q u!4 y! Over stroke stroke or less Component Parts No Body Piston Piston rod Collar Bushing Head cover Guide rod Plate Plate mounting bolt Plate mounting bolt B Replacement Parts/Seal Kit Description Material Note luminum alloy luminum alloy Carbon steel luminum alloy casted Bearing alloy Kit no. -PS -PS luminum alloy Carbon steel Carbon steel Carbon steel Carbon steel Hard anodized Chromated Hard chrome plated Painted ø Chromated ø Painted Hard chrome plated Nickel plated Nickel plated Nickel plated Contents For piston rod For guide rod Set of nos. Seal kit includes!7 Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S-0 ( g) Component Parts No. Description Material Note Retaining ring Carbon tool steel Phosphate coated 2 Bumper Urethane 3 Bumper B Urethane 4 Magnet Hexagon socket head taper plug Carbon steel Nickel plated Slide Bearing Bearing alloy 7 Piston seal NBR 8 Rod seal NBR 9 Gasket NBR Gasket B NBR MGJ -Z W MGQ MGG MGC MGF MGZ MGT 397 D- -X

62 Series S Dimensions S, 4 x YY depth YL øx H7 depth XL T-slot dimensions b øx H7 RB X R X ±0.02 a c d e X H7 XB XC XL Detailed figure of XX section 8 x RR depth RL QB Q WB Z W Section XX a 3.3 T-slot dimensions b c 2 d 8 e x NN depth NL Section XX Z W 4 x øo through 4 x øob counterbore depth OL L OC Section XX 4 x MM depth ML T X X ±0.02 ødb ød PW X U X ±0.02 H: T-slot for hexagon bolt VB V H øx H7 depth XL Q S F GC G P + Stroke FB C + Stroke B + Stroke + Stroke GB E 2 x P 2 x P (Plug) PB J G K øx H7 depth XL For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Stroke on page 392. Dimensions 398 Standard stroke 2,, 7, 0 2,, 7, 0 MM M2 x.7 M x 2.0 RL 4 S ML T 228 2, st Over st 8 8 NN M x. M2 x.7 U 70 V NL VB 0 38 E B C D DB F FB G G GB GC H H J K L 2, st Over st 8 8 O 44 OB OC OL 3 7. W 2 st, 7, 0 st Over 0 st Rc /4 Rc 3/8 33 P Nil N TF NPT /4 NPT 3/8 3 G /4 G 3/8 2 8 P PB. 29 WB X 2 st, 7, 0st Over 0 st PW 77 X Q XB Q 8 XC QB 7 9 XL 8 M M2 R 48 YY 3 47 RB 0 M2 x.7 M4 x RR M8 x.2 M x. YL 28 Z 28

63 Compact Guide Cylinder/High Precision Ball Bushing Bearing Type Series With End Lock: ø, ø2, ø, ø, ø, ø, ø, ø0 Series high precision ball bushing bearing type (except with end lock) product has been remodeled for a lightweight design. When selecting a product, refer to the new -Z series. MGJ -Z W MGQ MGG MGC MGF MGZ MGT 399 D- -X B

64 With end lock Compact Guide Cylinder/High Precision Ball Bushing Bearing Type Series With End Lock: ø, ø2, ø, ø, ø, ø, ø, ø0 How to Order H N Series high precision ball bushing bearing type (except with end lock) product has been remodeled for a lightweight design. When selecting a product, refer to the new -Z series. M9BW Compact Guide Cylinder High precision ball bushing bearing type 2 mm 2 mm mm mm 0 mm mm mm 0 mm Thread type Nil Rc N NPT TF G Cylinder stroke Refer to Standard Stroke on page. uto switch Nil Manual release type N Non-lock type L Lock type Lock position H Head end lock R Rod end lock Number of auto switches Nil 2 pcs. S pc. n n pcs. Without auto switch (Built-in magnet) Made to Order Specification For details, refer to page. C pplicable uto Switches/Refer to pages 893 to 07 for further information on auto switches. Type Reed auto switch Solid state auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) Magnetic field resistant (2-color indication) Electrical entry Indicator light Wiring (Output) Load voltage DC 3-wire (NPN) 3-wire (PNP) V,2 V 2-wire 2 V 3-wire (NPN) 3-wire (PNP) V,2 V Grommet Yes 2-wire V 2 V 3-wire (NPN) 3-wire (PNP) V,2 V 2-wire (Non-polar) 2 V 2 m type lead wire is only applicable to D-93. Lead wire length symbols: 0. m Nil (Example) M9NW m M (Example) M9NWM 3 m L (Example) M9NWL m Z (Example) M9NWZ Since there are other applicable auto switches than listed, refer to page for details. C uto switch model Perpendicular In-line M9NV M9PV M9BV M9NWV M9PWV M9BWV M9NV M9PV M9BV M9N M9P M9B M9NW M9PW M9BW M9N M9P M9B P3DW P4DW Lead wire length (m) 0. (Nil) (M) (Z) Pre-wired connector 3-wire V 9V 9 Yes (NPN equivalent) Grommet 0 V 93V wire V 2 V No 0 V or less 90V 90 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Consult with SMC regarding water resistant types with the above model numbers. pplicable load Solid state auto switches marked with are produced upon receipt of order. s to 0 are available for D-P4DW. s 2 to 0 are available for D-P3DW. For details about auto switches with pre-wired connector, refer to pages 90 and 9. For D-P3DW, refer to the WEB catalog. uto switches are shipped together (not assembled). 0 3 (L) IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PLC Relay, PLC

65 Minimum Proper Operating uto Compact Guide Cylinder High Precision Ball Bushing Bearing Type Series Specifications ction Fluid Proof pressure Max. operating pressure mbient and fluid temperature Piston speed Lubrication Stroke length tolerance Double acting ir. MPa.0 MPa to 0 C (No freezing) ø2 to ø to 0 mm/s ø, ø0 to 0 mm/s Non-lube +. 0 mm Minimum Operating Pressure Non-rotating accuracy of plate : ± 0.0 Plate displacement amount Symbol : 0.0 mm ( ø2- st, when Load mass is.7 kg.) ø to ø0 Standard Stroke Min. operating pressure 0. MPa Symbol Rubber bumper Made to Order: Individual Specifications (For details, refer to pages 7 and 8.) Specifications -X87 Lateral piping type (Change of plug position) Made to Order Specifications (For details, refer to pages 09 to 22.) Symbol -XC79 Specifications Machining tapped hole, drilled hole and pin hole additionally. Refer to pages 4 to for cylinders with auto switches. auto switch mounting stroke auto switch mounting position (detection at stroke end) and mounting height range switch mounting bracket: Part no. Standard stroke, 2,,,,,, 0 2,, 7, 0, 2,, 7, 0, 2, 0, 3, 0 Manufacture of Intermediate Stroke Description Part no. pplicable stroke Example Spacer installation type mm interval are available by installing a spacer on a standard stroke cylinder. Refer to How to Order for the standard specification. to 39 Part no.: -3-HN spacer mm in width is installed in a --HN. C dimension is 2 mm. MGJ -Z W MGQ MGG MGC MGF MGZ MGT Dimensions for all models are the same as the ball bushing bearing type. Refer to the following pages. With End Lock P.38 to 388 D- -X

66 Series Non-rotating ccuracy of Plate For non-rotating accuracy θ without load, use a value no more than the values in the table as a guide. +θ θ Caution Positioning accuracy for pin hole on the plate Dispersion of dimensions when machining each component will be accumulated in the plate pin hole positioning accuracy when mounting this cylinder. Below values are referred as a guide. [Side mounting] Pin hole L Non-rotating accuracy θ ±0.0 = Catalog dimension ± (0. + L x ) [mm] : To be 0. for ø, 0. Note) Displacement by load and self-weight deflection by plate and guide rod are not included. [Bottom mounting] Pin hole B L2 Pin hole B = ± ( L2 x 0.00) [mm] 2

67 Compact Guide Cylinder High Precision Ball Bushing Bearing Type Series Plate Displacement mount (Reference Values) Load from lateral direction Displacement 2 Plate displacement amount Load from lateral direction (N) Plate displacement amount Load from lateral direction (N) Plate displacement amount Load from lateral direction (N) / Plate displacement amount Plate displacement amount Plate displacement amount Load from lateral direction (N) / Load from lateral direction (N) Load from lateral direction (N) MGJ -Z W MGQ MGG MGC MGF MGZ MGT 2 Plate displacement amount Load from lateral direction (N) Load from lateral direction (N) Note ) The guide rod and self-weight for the plate are not included in the above displacement values. Note 2) Regarding the allowable rotational torque and the operating range as a lifter, refer to pages 34 to 32 in the standard type of Series L, since it is identical. Plate displacement amount D- -X

68 Series uto Switch Mounting uto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height pplicable cylinder: S (Heavy duty guide rod type) uto switch For D-M9 For D-Z7 ø, ø For D-M9V For D-Z For D-M9W For D-Y9 For D-M9WV For D-Y9 For D-M9 For D-Y7P For D-M9V For D-Y7PV For D-9 For D-Y7W For D-9V For D-Y7WV For D-Y7B B Hs For D-P3DW ( Cannot be mounted on bore sizes ø or less.) B ø ø Hs For D-P4DW ( Cannot be mounted on bore sizes ø2 or less.) ø ø.. Ht Ht Hs Hs Hs Less than 2 to 7 strokes For bore sizes ø through with two switches, one switch is mounted on each side. Hs uto Switch Proper Mounting Position uto D-M9 switch D-M9V model D-M9W D-M9WV D-M9 D-M9V Bore size 2. 8 B. 23. D-9 D-9V 8. 4 B D-Z7/Z D-Y9/Y7P D-Y9/Y7PV D-Y7W D-Y7WV D-Y7B 7. 3 B. 8. D-P3DW 8 3. Note 2) B 2 9 D-P4DW 7 2. Note ) djust the auto switch after confirming the operating conditions in the actual setting. Note 2) The auto switch mounting bracket BMG2-02 is used. B 8 uto Switch Mounting Height uto switch D-M9/M9W/M9/ model D-Z7/Z/Y9/Y7P D-Y7W/Y7B Hs. D-M9V D-M9WV D-M9V Hs Ht D-9V Hs Ht D-Y9 D-Y7PV D-Y7WV Hs Ht D-P3DW Note 2) Hs Ht D-P4DW Hs Ht 84. 4

69 uto Switch Mounting Series uto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height pplicable cylinder: Series S, With end lock With rod end lock For D-M9 For D-Z7 For D-M9V For D-Z For D-M9W For D-Y9 For D-M9WV For D-Y9 For D-M9 For D-Y7P For D-M9V For D-Y7PV For D-9 For D-Y7W For D-9V For D-Y7WV For D-Y7B uto Switch Proper Mounting Position uto switch model Bore size 2 0 D-M9 D-M9V D-M9W D-M9WV D-M9 D-M9V B D-9 D-9V With head end lock For D-M9 For D-Z7 For D-M9V For D-Z For D-M9W For D-Y9 For D-M9WV For D-Y9 For D-M9 For D-Y7P For D-M9V For D-Y7PV For D-9 For D-Y7W For D-9V For D-Y7WV For D-Y7B B D-Z7/Z D-Y9/Y7P D-Y9/Y7PV D-Y7W D-Y7WV D-Y7B B D-P3DW B 2. Note 3) 7. 9 D-P4DW B Note ) djust the auto switch after confirming the operating conditions in the actual setting. Note 2) The auto switch mounting bracket BMG2-02 is used. Note 3) When mounted on the head end of ø2, the tip of the BMG2-02 protrudes 3. mm from the cylinder body. uto Switch Proper Mounting Position uto switch model Bore size 2 0 D-M9 D-M9V D-M9W D-M9WV D-M9 D-M9V B D-9 D-9V B D-Z7/Z D-Y9/Y7P D-Y9/Y7PV D-Y7W D-Y7WV D-Y7B B D-P3DW B D-P4DW B Note ) djust the auto switch after confirming the operating conditions in the actual setting. Note 2) The auto switch mounting bracket BMG2-02 is used. B B uto switch uto switch For D-P3DW ( Cannot be mounted on bore sizes ø or less.) Ht ø2 to ø Hs ø, ø0 Hs uto Switch Mounting Height 2 0 Hs Ht For D-P4DW ( Cannot be mounted on bore sizes ø2 or less.) ø to ø Hs ø, ø0 Ht Caution. Hs For 2 stroke For bore sizes ø to with two auto switches, one switch is mounted on each side. Hs uto Switch Mounting Height 0 Hs Mounting of uto Switch Ht In the case of 2 st or less with head side end lock type, it might not insert auto switch from the rod side. In this case, install it after removing the plate temporarily. Regarding the plate removal and the way of assembly, please consult with SMC. MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

70 uto switch model D-M9V D-9V D-M9 D-M9W D-M9WV D-M9V D-M9 D-9 D-Z7 D-Z D-Y9 D-Y7P D-Y9 D-Y7PV D-Y7W D-Y7WV D-Y7B D-P3DW D-P4DW Series uto Switch Mounting 2 Minimum uto Switch Mounting Stroke Operating Range No. of auto switches mounted pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs., different side 2 pcs., same side ø ø2 ø ø ø ø ø ø0 Note ) Note ) Note 2) Note 2) Note 2) Note ) Note ) Note 2) Note 2) Note 2) Note 2) Note ) Confirm that it is possible to secure the minimum bending radius of mm of the auto switch lead wire before use. Note 2) Confirm that it is possible to securely set the auto switch(es) within the range of indicator green light ON range before use. For in-line entry type, please also consider Note ) shown above. uto switch model D-M9/M9V D-M9W/M9WV D-M9/M9V D-9/9V D-Z7/Z D-Y9/Y9 D-Y7P/Y7PV D-Y7W/Y7WV D-Y7B D-P3DW D-P4DW Since the operating range is provided as a guideline including hysteresis, it cannot be guaranteed (assuming approximately ±% dispersion). It may vary substantially depending on an ambient environment. Cylinders with an end lock are available in ø to ø0. The heavy duty guide rod type is available in ø and ø Note 2), Note 3) Note 2), Note 3) 7 Note 3) The minimum bending radius of the D-P4DW is mm. Note 4) The air cushion type is available in ø to ø0. Note ) The heavy duty guide rod type is available in ø and ø. uto Switch Mounting Bracket: Part No. uto switch model ø2 to ø ø2 ø to ø0 D-M9/M9V D-M9W/M9WV D-M9/M9V BMG2-02 D-9/9V D-P3DW BMG2-02 D-P4DW BMG-0 The air cushion type is available in ø to ø0 Cylinders with an end lock are available in ø to ø0. The heavy duty guide rod type is available in ø and ø.. For D-9(V)/M9(V)/ M9W(V)/M9(V) BMG2-02 Besides the models listed in How to Order, the following auto switches are applicable. For detailed specifications, refer to pages 893 to 07. uto switch type Model Electrical entry (Fetching direction) Features Reed Solid state D-Z73, Z7 D-Z D-Y9, Y9B, Y7PV D-Y7NWV, Y7PWV, Y7BWV D-Y9, Y9B, Y7P D-Y7NW, Y7PW, Y7BW D-Y7B Grommet (In-line) Grommet (Perpendicular) Grommet (In-line) Without indicator light Diagnostic indication (2-color indication) Diagnostic indication (2-color indication) Water resistant (2-color indication) D-PDW Magnetic field resistant (2-color indication) For solid state auto switches, auto switches with a pre-wired connector are also available. Refer to pages 90 and 9 for details. Normally closed (NC = b contact), solid state auto switch (D-F9G/F9H/Y7G/Y7H type) are also available. For details, refer to pages 9 and 93.

71 Series Made to Order: Individual Specifications Please contact SMC for detailed dimensions, specifications, and lead times. Symmetrical Port Position How to Order Symbol -X44 M L Stroke uto switch type Lead wire length No. of auto switches X44 Symmetrical port position Ports are mounted symmetrically. This makes it easy to remove and rotate piping when it is mounted on a wall where mounting space is limited. MGJ -Z Standard Symmetrical port position Standard W -X44 MGQ MGG Dimensions MGC MGF P + Stroke G 2 x P (Plug) PB MGZ MGT Common Dimensions: M, L G P PB D- 7 -X

Compact Guide Cylinder Series MGP

Compact Guide Cylinder Series MGP Compact Guide Cylinder Series MGP ø2, ø, ø, ø, ø, ø, ø, ø,, ø0 MGJ MGP MGQ MGG MGC MGF MGZ MGT Series Variations Series Bearing type Cushion 2 0 Page Standard type MGP With air cushion MGP With end lock

More information

22mm Space required between the bottom of the cylinder body and your equipment is reduced.

22mm Space required between the bottom of the cylinder body and your equipment is reduced. Compact Guide Cylinder ø2,,, ø2,,, ø0, ø63,, ø0 With air cushion Water resistant cylinder are now available. New Up to 7% Weight reduced! New Weight reduced by up to 7% with a shorter guide rod and thinner

More information

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder.

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder. Compact Guide Cylinder Series ø2,,, ø2,,, ø, ø63,, ø0 Up to Weight reduced by up to 24% with a shorter guide rod and thinner plate 24% Weight reduced! 3 types of bearing can be selected. Slide bearing

More information

Compact Guide Cylinder Series MGQ

Compact Guide Cylinder Series MGQ Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø0 ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP CT.S-7 C Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 New end lock type introduced to Series . Top mount Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Four mounting types

More information

Compact Guide Cylinder

Compact Guide Cylinder Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

Series MGP. Compact Guide Cylinder. New end lock type introduced to Series MGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100

Series MGP. Compact Guide Cylinder. New end lock type introduced to Series MGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 New end lock type introduced to Series.22- CL MLG CN CNG MNB CNS CLS CB CV/MVG CXW CXS CXT MX MXU MXH MXS MXQ MXF MXW MXP MG MGQ MGG MGC MGF

More information

Guide Table. ø40, ø63, ø100

Guide Table. ø40, ø63, ø100 Guide Table Series MGF ø, ø, ø Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Guide Table. MGF Series

Guide Table. MGF Series Guide Table MGF Series ø, ø, ø0 Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Compact Guide Cylinder with Lock

Compact Guide Cylinder with Lock Compact Guide Cylinder with Lock Series,,,, ø,,, ø0 CLG CL CN2 MLC Drop prevention when the pressure of air source is decreased or the residual pressure is released. Drop prevention for press fitting jig

More information

Series MGPS. Compact Guide Cylinder: ø50, ø80 MGP S Z73. How to Order. Applicable auto switches. Compact Guide Cylinder.

Series MGPS. Compact Guide Cylinder: ø50, ø80 MGP S Z73. How to Order. Applicable auto switches. Compact Guide Cylinder. Compact Guide Cylinder: Series S ø, Compact Guide Cylinder Compact guide cylinder Heavy duty guide rod type S Z73 mm mm How to Order Number of auto switches Nil S 2 pcs. 1 pc. Auto switch type Nil Without

More information

Guide Table. Series MGF

Guide Table. Series MGF Guide Table Series MGF ø, ø, ø0 Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Compact Slide. Series MXH ø6, ø10, ø16, ø20

Compact Slide. Series MXH ø6, ø10, ø16, ø20 Compact Slide Series ø, ø, ø, ø The use of an endless track linear guide produces a table cylinder having excellent rigidity, linearity and non-rotating accuracy. Endless track linear guide Series Variations

More information

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations.

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Free Mount Cylinder Series CU A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Space-saving The multiple surface direct mounting with a square

More information

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping.

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping. Dual Rod Cylinder / Series ø,,,,, Dual rod cylinder with guide function suitable for pick & place applications. Ball bushing bearings and slide bearings are standard for all series. Dimensions for ball

More information

Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43

Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43 CAT.EUS- B -UK Free Mount Cylinder A space-saving air cylinder with multiple surfaces capable of direct mounting. Offered in many variations. Space-saving The multiple surface direct mounted rectangular

More information

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8 Precision Cylinder Series, ø, ø6, ø, ø, ø, ø MXS Series Variations Model 8 Standard stroke (mm) 7 7 Rod end configuration Cushion Rubber bumper End lock Made to Order Rod Variable stroke/ through-hole

More information

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g.

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g. Compact Slide Series ø, ø, ø, ø RoHS Allowable moment MXS Improved by up to MXQ MXQ 2% MXF MXW MXJ MXP MXY With new high rigidity linear guide MTS Allowable moment improvement illustrated below Allowable

More information

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping.

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping. Dual Rod Cylinder J/ Series ø, ø, ø, ø, ø, Dual rod cylinder with guide function suitable for pick & place applications. Ball bushing bearings and slide bearings are standard for all series. Dimensions

More information

Miniature Guide Rod Cylinder ±0.1. Mounting from 2 directions

Miniature Guide Rod Cylinder ±0.1. Mounting from 2 directions Miniature Guide Rod Cylinder Series Non-rotating accuracy : Height ±0.1 Mounting from 2 directions idth Overall length Two auto switches can be mounted even for mm strokes Integral wiring/piping to one

More information

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil With auto switch RSG RSDG With auto switch (uilt-in magnet) uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the

More information

Compact Cylinder. Series CQS CUJ CU CQS CQ2 RQ CQM MU

Compact Cylinder. Series CQS CUJ CU CQS CQ2 RQ CQM MU Compact Cylinder Series ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility for

More information

Mini Free Mount Cylinder

Mini Free Mount Cylinder Mini Free Mount Cylinder Series ø, ø, ø, ø, ø, ø1, ø Series 1 ction Stroke 1 2 0 0 0 Clean uto switch series None Rod end Male threaded Without thread Solid state switch D-F D-M9 D-M9 W Female threaded

More information

Guide Cylinder MGG. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. Integration of a basic cylinder and guide rods

Guide Cylinder MGG. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. Integration of a basic cylinder and guide rods Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Guide Cylinder Series MGG ø, ø, ø, ø, ø, ø, ø, ø Integration of a basic cylinder and guide

More information

Heavy Duty Stopper Cylinder

Heavy Duty Stopper Cylinder Heavy Duty Stopper Cylinder Series ø, ø32 To stop pallets gently Stopper cylinder with built-in shock absorber Amount of energy absorption can be adjusted to suit the load. Stops the workpiece gently with

More information

Free Mount Cylinder for Vacuum

Free Mount Cylinder for Vacuum Free Mount Cylinder for Vacuum Series A free mount cylinder with a vacuum passage in the rod to meet the requirements for Air cylinder + Vacuum pad. A vacuum passage has been provided in the rod of the

More information

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added.

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added. ir Cylinder ø1, ø16 Double foot Double-side bossed added to the mounting types. 4 types 7 types Improved amount of mounting freedom Head cover with boss is added. Head flange are Double foot Double-side

More information

How to Order M9BW. Action. Double acting Single acting. Load voltage Electrical entry direction M9NWV M9NW 12 V 5 V, M9BWV M9BW 12 V 12 V

How to Order M9BW. Action. Double acting Single acting. Load voltage Electrical entry direction M9NWV M9NW 12 V 5 V, M9BWV M9BW 12 V 12 V Angular Type Air Gripper/Standard Type 2 Series ø, ø1, ø20, ø25 How to Order Angular type air gripper 2 20 Bore size mm 1 1 mm 20 20 mm 25 25 mm D S Action D Double acting Single acting M9BW Made to Order

More information

180 Angular Style Air Gripper

180 Angular Style Air Gripper 8 Angular Style Air Gripper Series 2/2 Cam Style / Rack & Pinion Style 99 8 Angular Style Air Gripper Cam Style Rack & Pinion Style Series 2/2 Series 2/Cam Style Light and compact size in small bore sizes

More information

Compact Cylinder/Plate type

Compact Cylinder/Plate type Compact Cylinder/Plate type Series :,,, Width: Reduced by up to % (compared with SMC series) Total length: Reduced by up to % Volume: Reduced by up to 1% Weight: Reduced by up to % (compared with SMC series

More information

Parallel Style Air Gripper: Wide Type

Parallel Style Air Gripper: Wide Type Parallel Style Air Gripper: Wide Type Series MHL Built-in dust-protection mechanism A scraper with a dust lip is adopted for all rod rotating parts. A large amount of gripping force is provided through

More information

Dual Rod Cylinder. ø6, ø10, ø15, ø20, ø25, ø32. Dual rod cylinder with guide function suitable for pick & place applications.

Dual Rod Cylinder. ø6, ø10, ø15, ø20, ø25, ø32. Dual rod cylinder with guide function suitable for pick & place applications. Dual Rod Cylinder Series J/ ø, ø0, ø, ø, ø, Dual rod cylinder with guide function suitable for pick & place applications. Twice the thrust Non-rotating accuracy ±0. Ball bushing bearings and slide bearings

More information

69% 30.5 mm 16 mm. Compact Guide Cylinder. Compact. lighter 0.32 kga0.1 kg (Compared with the current MGP-Z series, ø16, 10 mm stroke) Weight

69% 30.5 mm 16 mm. Compact Guide Cylinder. Compact. lighter 0.32 kga0.1 kg (Compared with the current MGP-Z series, ø16, 10 mm stroke) Weight Compact Guide Cylinder ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 RoHS Compact Overall length shortened New s ø80, ø100 added. Port thread types NPT, G added. Height shortened JMGP ø32 25 mm stroke

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR2 CRU2 CR1 MSU CRJ Rotation 360 type MSQ 360 MSZ MSQ MRQ Series Variations Page Rotating angle 80 to 0 170

More information

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types ir Cylinder Ø 6, Ø 1, Ø New RoS Double foot ead flange Double-side bossed added to the mounting types. 4 types 7 types New or Ø 6, 3 types are 6 types Double foot Double-side bossed ead flange ead cover

More information

Non-rotating Double Power Cylinder. Double Power Cylinder MGZ. (without non-rotating MGJ MGP -Z MGP MGPW MGQ MGG MGC MGF MGT D- -X

Non-rotating Double Power Cylinder. Double Power Cylinder MGZ. (without non-rotating MGJ MGP -Z MGP MGPW MGQ MGG MGC MGF MGT D- -X Non-rotating Double Power Cylinder Double Power Cylinder (without non-rotating Series Series R mechanism) MGJ -Z W MGQ MGG MGC MGF MGT 23 D- -X Non-rotating Double Power Cylinder Double extension output

More information

MGZ. Non-rotating Double Power Cylinder. Double Power Cylinder MGJ MGP MGPW MGQ MGG MGC MGF MGT D- -X

MGZ. Non-rotating Double Power Cylinder. Double Power Cylinder MGJ MGP MGPW MGQ MGG MGC MGF MGT D- -X Non-rotating Double Power Cylinder Double Power Cylinder (without non-rotating Series Series R mechanism) 23 MGJ -Z W MGQ MGG MGC MGF MGT D- -X Tube rod diameter External dimension Non-rotating Double

More information

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E -UK Dual-Rod Cylinder Series CXS New: CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ Dual-Rod Cylinder with guide functio for pick-and-place applications Series CXS! Twice the

More information

Angular Style Air Gripper

Angular Style Air Gripper Angular Style Air Gripper Series /A/M 15 Angular style air gripper Series /A/M - Auto switch is attachable. 8 mm x 0 mm x mm g Body option (Only for A-) Side piping Port Port A- Short body. 1 mm x 0 mm

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator CRQ2 Series Rack & Pinion Type/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR 2 CR1 MSU CRJ CR1 CRQ2 MSQ MSZ Rotation 360 type 360 CRQ2 MSQ MRQ Series Variations Page Rotating angle

More information

Series MXH/ ø6, ø10, ø16, ø20

Series MXH/ ø6, ø10, ø16, ø20 Compact Slide Series / ø, ø, ø, ø The use of an endless track linear guide produces a table cylinder having excellent rigidity, linearity and non-rotating accuracy. CL MLG CNA CNG MNB CNS CLS CB CV/MVG

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm 360 type 360 CR2 CRU2 CR1 MSU CRJ CR1 MSQ MSZ MSQ MRQ Series Variations Standard Made to Order Rotating angle

More information

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover.

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover. Air Cylinder 1 Series ø32, ø40, ø50, ø63, ø80, ø100, ø125 RoHS 10 (ø50-100 stroke) % lighter Current model 1.9 kg 1 Series 1.7 kg J 1 Reduced weight by changing the shape of the rod cover and head cover.

More information

3 Position Cylinder. RZQ Series. Provides intermediate stop mechanism. ø32, ø40, ø50, ø63. 2-stage stroke enabled with a small increase in length

3 Position Cylinder. RZQ Series. Provides intermediate stop mechanism. ø32, ø40, ø50, ø63. 2-stage stroke enabled with a small increase in length Position ylinder Series ø, ø, ø, ø Provides intermediate stop mechanism 2-stage stroke enabled with a small increase in length Overall length of cylinder tube DQ2 Full stroke First-stage stroke dditional

More information

Mini Rotary Actuator/Rack & Pinion Style

Mini Rotary Actuator/Rack & Pinion Style Mini Rotary Actuator/Rack & Pinion Style Series CRJ :, CRB2 CRBU2 CRB MSU CRJ CRA CRQ2 MSQ MSZ CRQ2X MSQX MRQ PAT. PEND D- 79 Mini Rotary Actuator Series CRJ Rack & Pinion Style/:, Compact 9.5 23.5 43(54)

More information

Air Slide Table. Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece

Air Slide Table. Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece ir Slide Table Series Height: mm/width: mm/length: mm () Front mounting accuracy: 0.01 mm Top mounting accuracy: 0.0 mm Traveling parallelism: 0.00 mm Note 1) Note ) Integrated front mounting part and

More information

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E -UK Dual-Rod Cylinder Series New: Dual-Rod Cylinder with Air Cushion Compact Type Series J Dual-Rod Cylinder with guide function for pick-and-place applications Series! Twice the thrust Non-rotating

More information

Guide Cylinder/Compact Type

Guide Cylinder/Compact Type Guide Cylinder/Compact Type Series ø, ø, ø, ø, ø Integration of guide rods and a base cylinder ir cushion is standard. Enables the impact to be absorbed at the stroke end when the cylinder is operated

More information

Mini Rotary Actuator/Rack & Pinion Style

Mini Rotary Actuator/Rack & Pinion Style Mini Rotary Actuator/Rack & Pinion Style Series CRJ :, CRB2 CRBU2 CRB MSU CRJ CRA CRA CRQ2 MSQ MSZ CRQ2X MSQX MRQ PAT. PEND D- 79 Mini Rotary Actuator Series CRJ Rack & Pinion Style/:, Compact 9.5 23.5

More information

Series MLGP. Low Profile Guide Cylinder with Lock. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100

Series MLGP. Low Profile Guide Cylinder with Lock. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 CAT.ES-4 A Low Profile Guide Cylinder with Lock Series MLGP,,,, ø,,, ø0 Drop prevention when supply pressure falls or residual pressure is released Drop prevention for press fitting jig Drop prevention

More information

Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece

Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece ir Slide Table Series RoHS Height: mm/width: mm/length: mm () Traveling parallelism: 0.00 mm Note 1) Front mounting accuracy: 0.01 mm Note ) Top mounting accuracy: 0.0 mm Integrated front mounting part

More information

Dual rod cylinder with guide function for pick & place applications.

Dual rod cylinder with guide function for pick & place applications. Dual Rod Cylinder Series CXS ø, ø0, ø, ø, ø2, Dual rod cylinder with guide function for pick & place applications. Series CXS Twice the thrust Non-rotating accuracy ±0. MX MY CY MG CX - Ball bushing bearings

More information

Compact Hydraulic Cylinder

Compact Hydraulic Cylinder ompact Hydraulic ylinder Series HQ HQ Series HQ HK HN HM HS H2 H Nominal pressure:. MPa ore size :,,,,,, . MPa ompact Hydraulic ylinder Double cting/single Rod Series H Q ø, ø, ø, ø, ø, ø, ø With uto Switch

More information

CAT.ES20-53 E. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E Dual-Rod Cylinder Series New: Dual-Rod Cylinder with Air Cushion Compact Type Series J Dual-Rod Cylinder with guide function for pick-and-place applications Series! Twice the thrust Non-rotating

More information

22mm. Compact Guide Cylinder (Basic type) New. Up to. Series MGP. Weight reduced!

22mm. Compact Guide Cylinder (Basic type) New. Up to. Series MGP. Weight reduced! 1-161 Compact Guide Cylinder (Basic type) ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Up to 17% Weight reduced! New Weight reduced by up to 17% with a shorter guide rod and thinner plate Guide rod

More information

2 way basic mounting: Through-hole or both ends tapped

2 way basic mounting: Through-hole or both ends tapped Compact Cylinder Series ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility for

More information

2 way basic mounting: Through-hole or both ends tapped

2 way basic mounting: Through-hole or both ends tapped Compact Cylinder Series CQS ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility

More information

Mechanically Jointed Rodless Cylinders

Mechanically Jointed Rodless Cylinders Mechanically Jointed Rodless Cylinders MY Series Basic short type (Rubber bumper) MY Series Bore sizes ø, ø, ø0 added MYB MY Basic standard type (ir cushion) MYB MYB Series MYM MYC MY MY T Bore sizes ø,

More information

Magnetically Coupled Rodless Cylinder Slider Type: Ball Bushing Bearing. How to Order CY1L 25 H 300 J79W. Load voltage 5 V 200V 100 V 12 V 5 V, 12 V

Magnetically Coupled Rodless Cylinder Slider Type: Ball Bushing Bearing. How to Order CY1L 25 H 300 J79W. Load voltage 5 V 200V 100 V 12 V 5 V, 12 V Magnetically Coupled Rodless Cylinder Slider Type: all ushing earing Series CY1L ø, ø, ø, ø, ø, ø, ø How to Order CY1L H 00 J79W Slider type (all bushing bearing) mm mm mm mm mm mm mm Magnetic holding

More information

Air Slide Table. Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece

Air Slide Table. Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece ir Slide Table Series Height: mm/width: mm/length: mm () Front mounting accuracy: 0.01 mm Top mounting accuracy: 0.0 mm Traveling parallelism: 0.00 mm Note 1) Note ) Integrated front mounting part and

More information

Rotary Actuator. New RoHS. New. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB 2. Standard type/series CRB2

Rotary Actuator. New RoHS. New. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB 2. Standard type/series CRB2 Rotary Actuator Vane Type 1, 15, 2, 3, 4 Standard Type Free Mount Type Many combinations available! Standard type/series Piping ports are located on the flat surface. Fittings can be secured firmly, piping

More information

Slide Unit. CX2/CXWM/CXWL Series. Slide Bearing/CX2:ø10, ø15, ø25 CXWM:ø10, ø16, ø20, ø25, ø32 Ball Bushing Bearing/CXWL:ø10, ø16, ø20, ø25, ø32

Slide Unit. CX2/CXWM/CXWL Series. Slide Bearing/CX2:ø10, ø15, ø25 CXWM:ø10, ø16, ø20, ø25, ø32 Ball Bushing Bearing/CXWL:ø10, ø16, ø20, ø25, ø32 Slide Unit CX/M/L Series Slide Bearing/CX:ø0, ø, ø5 M:ø0, ø, ø0, ø5, ø3 Ball Bushing Bearing/L:ø0, ø, ø0, ø5, ø3 Provided with shock absorbers to absorb impact and noise. The slide unit can absorb energy

More information

Rod end male thread. With rubber bumper 056(9/16") 075(3/4") 106(1 1/16") 150(1 1/2") 250(2 1/2") 300(3")

Rod end male thread. With rubber bumper 056(9/16) 075(3/4) 106(1 1/16) 150(1 1/2) 250(2 1/2) 300(3) T.ID0-1 New ompact ylinder Series NQ8 ore size: 06(9/16 ),(/ ),106(1 1/16 ),(1 1/ ) 00( ),0( 1/ ),00( ),00( ) Now available in 00 ( ) and 00 ( ) bore sizes Standard type ctuation Style uilt-in magnet Rod

More information

Slide Unit. Bore size. ø15 (2) ø10 (2) ø16 (3) ø20 (2) Ball bushing bearing Slide bearing. ø25 (3) (3) ø32 (3)

Slide Unit. Bore size. ø15 (2) ø10 (2) ø16 (3) ø20 (2) Ball bushing bearing Slide bearing. ø25 (3) (3) ø32 (3) Slide Unit Series CX/M/L Slide Bearing/CX:ø, ø, ø5 M:ø, ø6, ø0, ø5, ø3 Ball Bushing Bearing/L:ø, ø6, ø0, ø5, ø3 Provided with shock absorbers to absorb impact and noise. The slide unit can absorb energy

More information

MHR3/MDHR3 Series. Rotary Actuated Air Gripper/3-Finger Type. Size: 10, 15 MDHR 3 10 R M9N S. How to Order. Without auto switch

MHR3/MDHR3 Series. Rotary Actuated Air Gripper/3-Finger Type. Size: 10, 15 MDHR 3 10 R M9N S. How to Order. Without auto switch Rotary ctuated ir Gripper/3-Finger Type MHR3/MDHR3 Series Size:, 1 How to Order Without auto switch MHR 3 R Connecting port R ody side R: ody side Port With auto switch (uilt-in magnet) MDHR 3 R M9N S

More information

10%lighter. 1.7 kg. 1.9 kg. Air Cylinder. New. Weight. Reduced weight by changing the shape of the rod cover and head cover. Series MB1 CAT.

10%lighter. 1.7 kg. 1.9 kg. Air Cylinder. New. Weight. Reduced weight by changing the shape of the rod cover and head cover. Series MB1 CAT. ir ylinder ø32, ø40, ø50, ø63, ø80, ø100, ø125 New RoS Weight (ø50-100 stroke) 10%lighter Existing model 1.9 kg New Series M1 1.7 kg Reduced weight by changing the shape of the rod cover and head cover.

More information

3 Position Cylinder. ø32, ø40, ø50, ø63 RZQ CDQ2. Bore size (mm)

3 Position Cylinder. ø32, ø40, ø50, ø63 RZQ CDQ2. Bore size (mm) Position ylinder Series ø, ø, ø, ø Provides intermediate stop mechanism 2-stage stroke enabled with a small increase in length Overall length of cylinder tube First-stage stroke Full stroke dditional cylinder

More information

Rotary Actuated Air Gripper

Rotary Actuated Air Gripper Rotary ctuated ir Gripper MHR, MDHR/MHR3, MDHR3 -finger type: Size, 15,, 3/ 3-finger type: Size, 15 High Precision - Repeatability ±.1 mm Parallel opening and closing mechanism utilizing a cross roller

More information

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting.

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting. Compact Cylinder: Type Series ø, ø, ø, ø How to Order Without auto switch D With auto switch CDQS D FW S Number of auto switches L F G D, uilt-in magnet Mounting style Through-hole/oth ends tapped common

More information

Toggle Type Air Gripper

Toggle Type Air Gripper ø2, ø40, ø50, ø6 Ideal for gripping heavy workpiece Toggle mechanism is adopted. Holds workpiece even when pressure drops. The toggle mechanism that activates when the finger closes realizes strong and

More information

10% lighter kg kg. Air Cylinder. MB Series. ø32, ø40, ø50, ø63, ø80, ø100, ø125

10% lighter kg kg. Air Cylinder. MB Series. ø32, ø40, ø50, ø63, ø80, ø100, ø125 ir Cylinder M Series ø3, ø40, ø50, ø63, ø80, ø00, ø5 RoHS 0% lighter CJ (ø40-00 stroke) Weight M Series 0.9 kg CJP CJ JCM CM Current model CM3 CG.0 kg CG3 JM Reduced weight by changing the shape of the

More information

49.5 mm Overall. 30 mm MXZ ø20. Compact. Compact Cylinder with Linear Guide. MXZ Series CAT.ES20-236A. ø12, ø16, ø20, ø25. MXZ ø20, 10 mm stroke.

49.5 mm Overall. 30 mm MXZ ø20. Compact. Compact Cylinder with Linear Guide. MXZ Series CAT.ES20-236A. ø12, ø16, ø20, ø25. MXZ ø20, 10 mm stroke. Compact Cylinder with Linear Guide ø12, ø16, ø20, ø25 RoHS Compact 49.5 mm Overall length MXZ ø20, 10 mm stroke 30 mm MXZ ø20 Width Design and assembly time is reduced due to integration of a linear guide

More information

Series MGF ø40, ø63, ø100

Series MGF ø40, ø63, ø100 Guide Table Series MGF ø, ø, ø How to Order MGF Z7 Guide table Number of auto switches 2 S 1 Cylinder bore size/ Standard stroke,, 7,,, 7,,, 7, Auto switch Without auto switch * Refer to the table below

More information

Compact Cylinder: Large Bore Size Type Double Acting, Double Rod. How to Order. Cushion C Rubber bumper. Action. D Double acting

Compact Cylinder: Large Bore Size Type Double Acting, Double Rod. How to Order. Cushion C Rubber bumper. Action. D Double acting Compact Cylinder: Large Bore Size Type Double Acting, Double Rod Series CQ2W ø, ø, ø, ø, ø Without auto switch With auto switch B Built-in magnet CQ2WB CDQ2WB Double rod ounting style Through-hole/Both

More information

/ ø6, ø10, ø16, ø20 A table cylinder suitable for short pitch mounting

/ ø6, ø10, ø16, ø20 A table cylinder suitable for short pitch mounting roduces a table cylinder non-rotating accuracy MXH / ø, ø, ø1, ø A table cylinder suitable for short pitch mounting Application example Auto switches offer numerous variations Reed switches, solid state

More information

Low Profile Air Gripper. Series MHF2. Low profile air gripper with space-saving design is newly released. 5-77

Low Profile Air Gripper. Series MHF2. Low profile air gripper with space-saving design is newly released. 5-77 Low Profile Air Gripper Low profile air gripper with space-saving design is newly released. 5-77 Low Profile Air Gripper Height is approximately / the size of an equivalent Series MHZ2. MHZ2-D 42 Bore

More information

Low Profile Air Gripper

Low Profile Air Gripper Low Profile Air Gripper Series MHF2 MHZ MHF MHL MHR MHK MHS MHC MHT MHY MHW -X Low profile air gripper with space-saving design MRHQ MA D- Courtesy of Steven ngineering, Inc.-2 Ryan Way, South San Francisco,

More information

Wide Type Parallel Style Air Gripper

Wide Type Parallel Style Air Gripper Wide Type Parallel Style ir Gripper ø, ø6, ø2, ø25 Weight Max. % reduction 585 g 525 g ø6, Opening/Closing stroke: 3 mm RoHS Weight reduced by the change of the body shape and internal construction M Dust

More information

Series RSH/RS1H. To stop pallets gently. Heavy Duty Stopper Cylinder. Stopper cylinder with built-in shock absorber. ø20, ø32 ø50, ø63, ø80

Series RSH/RS1H. To stop pallets gently. Heavy Duty Stopper Cylinder. Stopper cylinder with built-in shock absorber. ø20, ø32 ø50, ø63, ø80 1 eavy Duty Stopper Cylinder Series RS/RS1 ø, ø ø, ø, ø To stop pallets gently CX CY RC RS A MI S C G5-S Stopper cylinder with built-in shock absorber - -9-1 2 eavy Duty Stopper Cylinder Series RS/RS1

More information

Air Cylinder. New RoHS. Series CG1. Female rod end available as standard. Rod end styles suitable for the application can be selected.

Air Cylinder. New RoHS. Series CG1. Female rod end available as standard. Rod end styles suitable for the application can be selected. ir Cylinder ø 20, ø 25, ø 32, ø 40, ø 50, ø 63, ø 80, ø 100 New RoS Female rod end available as standard Selectable Rod end styles suitable for the application can be selected. Female thread Male thread

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary Actuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CRB2 CRBU2 CRB1 MSU CRJ CRA1 Rotation 360 type 360 MSZ MRQ Series Variations Page Rotating angle 80 to 0 170

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPG AND DELIVER TENS OF THOUSANDS OF -STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

Standard Type Dual-Rod Cylinder. ø6, ø10, ø15, ø20, ø25, ø32. How to Order

Standard Type Dual-Rod Cylinder. ø6, ø10, ø15, ø20, ø25, ø32. How to Order Standard Type ual-rod ylinder Series ø, ø, ø, ø, ø2, ø32 ompact Type J M L M earing type Slide bearing all bushing bearing How to Order 0 Y7W S Number of auto switches Nil 2 pcs. S pc. n "n" pcs. ore size/standard

More information

Basic type/direct mount type

Basic type/direct mount type Basic type/direct mount type Series / ø, ø, ø, ø, ø, ø, ø, ø, ø3 CYS -Z CYL CYH CYF CYP 443 D- -X Technical data Magnetically Coupled Rodless Cylinder Direct mount type Series / Basic type Improved durability

More information

180 Angular Style Air Gripper

180 Angular Style Air Gripper 18 Angular tyle Air Gripper eries 2/2 Cam tyle / Rack & Pinion tyle -X D- Courtesy of teven Engineering, Inc.-2 Ryan Way, outh an Francisco, CA 98-67-Main ffice: (6) 88-92-utside Local Area: (8) 28-92-www.stevenengineering.com

More information

Mechanically Jointed Hy-rodless Cylinder with Brake

Mechanically Jointed Hy-rodless Cylinder with Brake Mechanically Jointed y-rodless Cylinder with Brake Series ø, ø, ø Brake mechanism has been compactly integrated into the slide table which enables intermediate stops of the rodless cylinder. Large holding

More information

Direct Mount Type. REBR Series. ø15, ø25, ø32. REA REB REC Smooth MQ RHC RZQ D- -X. Low Speed

Direct Mount Type. REBR Series. ø15, ø25, ø32. REA REB REC Smooth MQ RHC RZQ D- -X. Low Speed Direct Mount Type R Series ø, ø, ø 85 R Series Selection Fn: llowable driving force (N) MD: Maximum allowable moment when connection fitting, etc., is directly loaded (N m) Pv: Maximum operating pressure

More information

Double Power Cylinder. Non-rotating Double Power Cylinder. Series MGZ. Series MGZR (without MGJ MGP MGQ MGG MGC MGF MGZ MGT. non-rotating mechanism)

Double Power Cylinder. Non-rotating Double Power Cylinder. Series MGZ. Series MGZR (without MGJ MGP MGQ MGG MGC MGF MGZ MGT. non-rotating mechanism) Non-rotating Double Power Cylinder Series Double Power Cylinder Series R (without non-rotating mechanism) 2 Non-rotating Double Power Cylinder Double extension output power!! Our unique construction doubles

More information

Platform Cylinder. CXT Series. ø12, ø16, ø20, ø25, ø32, ø40. A highly rigid and highly accurate slide table integrated with an actuator.

Platform Cylinder. CXT Series. ø12, ø16, ø20, ø25, ø32, ø40. A highly rigid and highly accurate slide table integrated with an actuator. Platform Cylinder Series ø, ø, ø, ø, ø, ø highly rigid and highly accurate slide table integrated with an actuator. Two types of guide rod bearings to accommodate your application For heavy loads all bushing

More information

Parallel Style Air Gripper

Parallel Style Air Gripper INFRMATIN Parallel tyle Air Gripper With Dust Cover Model variations with excellent dust proof and drip proof dust cover are expanded. MHZL2 Long stroke type MHZL2 series ø1, ø16 and ø2 with dust cover

More information

Rotary Actuator/Vane Type

Rotary Actuator/Vane Type Rotary Actuator/Vane Type CRB2 Series : 1, 15, 2, 3, 4 Standard Type Free Mount Type Many combinations available! Standard type/crb2 Series Piping ports are located on the flat surface. Fittings can be

More information

How to Order. Manual release type. Lock position. H Head end lock. With rod boot. Nil J K M9NWV M9NW H7C M9PWV M9PW M9BWV M9BW M9NAV M9NA M9PAV M9PA

How to Order. Manual release type. Lock position. H Head end lock. With rod boot. Nil J K M9NWV M9NW H7C M9PWV M9PW M9BWV M9BW M9NAV M9NA M9PAV M9PA Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - www.cmafh.com CDG1 With auto switch (uilt-in magnet) Mounting style asic style L xial foot style F Rod side

More information

High Rigidity/ High Precision Guide Type ø50, ø63. The use of two linear guides allows a maximum load of 320kg. (ø63) Rodless cylinder MY1BH SMC

High Rigidity/ High Precision Guide Type ø50, ø63. The use of two linear guides allows a maximum load of 320kg. (ø63) Rodless cylinder MY1BH SMC MYHT Series High Rigidity/ High Precision Guide Type ø, ø6 The use of two linear guides allows a maximum load of kg. (ø6) Rodless cylinder MYBH SMC 2 linear guides Easy maintenance is stressed by a revolutionary

More information

Parallel Style Air Gripper Series MHZ

Parallel Style Air Gripper Series MHZ Parallel tyle ir Gripper eries MHZ 17 Integral linear guide used for high rigidity Repeatability: ±.1 mm Low profile Martensitic stainless steel High degree of mounting flexibility Can be mounted five

More information

Air Slide Table. ø8, ø12, ø16, ø20, ø25. Linear guide table provides long stroke. Table rigidity is constant throughout entire stroke.

Air Slide Table. ø8, ø12, ø16, ø20, ø25. Linear guide table provides long stroke. Table rigidity is constant throughout entire stroke. ir Slide Table Series MX ø, ø2, ø, ø2, ø2 inear guide table provides long stroke. Table rigidity is constant throughout entire stroke. ong stroke (Max. mm) inear guide provides long stroke, and it obtains

More information

Basic type / Direct mount type

Basic type / Direct mount type Basic type / Direct mount type Series / ø, ø, ø, ø, ø, ø, ø, ø, ø3 CYS CYL CY CYF Courtesy of Steven Engineering, Inc.- Ryan Way, South San Francisco, CA 0-30-Main Office: () -0-Outside Local Area: (00)

More information

Parallel Style Air Gripper

Parallel Style Air Gripper Parallel tyle Air Gripper eries MHZ MHZ MH -X D- Courtesy of teven Engineering, Inc.-3 Ryan Way, outh an Francisco, CA 98-37-Main Office: () 88-9-Outside Local Area: (8) 8-9-www.stevenengineering.com 373

More information

Sine Rodless Cylinder Series RE asic Type/ø, ø, ø, ø, ø3 asic type Sine rodless cylinder (basic type) Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and

More information

Compact Hydraulic Cylinder. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order Z73. Bore size. 20mm 25mm 32mm 40mm 50mm 63mm 80mm 100mm

Compact Hydraulic Cylinder. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order Z73. Bore size. 20mm 25mm 32mm 40mm 50mm 63mm 80mm 100mm ompact ydraulic ylinder MPa Series KG ø, ø, ø, ø, ø, ø, ø, ø0 With uto Switch With auto switch (built-in magnet) KG DKG Mounting: asic type 0 ore size ow to Order mm mm mm mm mm mm mm 0mm Z3 Refer to "uto

More information

Mechanically Jointed Rodless Cylinder

Mechanically Jointed Rodless Cylinder Mechanically Jointed Rodless Cylinder MY Series ø, ø, ø MYB MY MYB MYM MYC MY MY T MY W MYC MY /T MYA MYB MYM Compact and low profile design D- -X Technical Data Mechanically Mechanically Jointed Jointed

More information