10% lighter kg kg. Air Cylinder. MB Series. ø32, ø40, ø50, ø63, ø80, ø100, ø125

Transcription

1 ir Cylinder M Series ø3, ø40, ø50, ø63, ø80, ø00, ø5 RoHS 0% lighter CJ (ø40-00 stroke) Weight M Series 0.9 kg CJP CJ JCM CM Current model CM3 CG.0 kg CG3 JM Reduced weight by changing the shape of the rod cover and head cover. M M C CS CS D- -X Technical Data 387

2 Double acting, Single rod M Series ø3, ø40, ø50, ø63, ø80, ø00, ø5 Part numbers with rod end bracket and/or pivot bracket available Not necessary to order a bracket for the applicable cylinder separately Note) Mounting bracket is shipped together with the product, but not assembled. Example) MD D Mounting type Z- N V -M9W Pivot bracket Nil No bracket N Pivot bracket is shipped together with the product, but not assembled. pplicable to only D (Double clevis) and T (Center trunnion) mounting types. Double clevis Center trunnion Rod end bracket Nil No bracket V Single knuckle joint W Double knuckle joint With rod end bracket V: Single knuckle W: Double joint knuckle joint Various mounting bracket options Suitable mounting brackets can be selected for the installation condition. D: Double clevis Improved amount of mounting freedom N: Double clevis pivot bracket C: Single clevis G: Head flange : asic V: Single knuckle joint L: xial foot N: Trunnion pivot bracket W: Double knuckle joint F: Rod flange L: xial foot T: Center trunnion N: Trunnion pivot bracket 388

3 ir Cylinder Lightweight Reduced weight by changing the shape of the rod cover and head cover. [kg] M Reduction rate [%] Current model t 00 stroke Series Variations Standard Single rod M-Z Mounting dimensions are the same as the current product. Series Type Cushion Double acting, Single rod Rubber ir Piston speed: Max. 000 mm/s (ø3 to ø5) Load yield: See table below. [kg] Maximum load mass Speed: 00 mm/s No environmental hazardous substances used Lead free bushing is used as sliding material. Compliant with EU RoHS directive. pplicable speed/load 3 uilt-in With magnet rod boot Port Various switches such as compact auto switches and magnetic field resistant auto switches can be mounted. Compact auto switches D-M9 D-9 Magnetic field resistant auto switches D-P3DW D-P3DW D-P4DW ø3 only Page 39 CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS Standard Double rod MW-Z Double acting, Double rod Rubber ir 40 Non-rotating rod Single rod MK-Z Double acting, Single rod Rubber ir 408 Non-rotating rod Double rod MKW-Z Double acting, Double rod Rubber ir 4 With end lock M Double acting, Single rod Rubber ir 46 Smooth Cylinder MY-Z Double acting, Single rod Rubber est Pneumatics No.w-3 D- Low friction M Q Use the new series Smooth Cylinder MY Series to realize bi-directional low friction and low-speed operation. (Refer to the est Pneumatics No.w-3.) 389 -X Technical Data

4 Combinations of Standard and Made to Order Specifications M Series V : Standard : Made to Order v : Special product (Please contact SMC for details.) : Not available Symbol Standard Standard Specifications Series ction/ Type Cushion Page pplicable bore size Single rod M-Z (Standard type) Double acting Double rod ir Rubber ir Rubber ø3 to ø00 ø5 ø3 to ø00 ø5 ø3 to ø00 ø5 ø3 to ø00 ø5 V V V V V V V V Long st Long stroke V V V V V V V V ø3 to ø5 D uilt-in magnet V V V V V V V V Ml-l J K With rod boot V V V V V V V V 5 Copper (Cu) and Zinc (Zn)-free Note ) ø3 to ø00 V v v v v v v v Ml R V Water resistant V v V v V v V v 0- Clean series Note 6) ø3 to ø5 v v v v v v v v 0- Copper Note 5) and Fluorine-free Note 6) Xl Change of rod end shape X5 Oversized rod cylinder Note 6) v v v v v v v X6 Heat resistant cylinder ( 0 to 50 C) v v v v v X3 Low speed cylinder (5 to 50 mm/s) Note 6) v v v v v v XC3 Special port location Note 6) Note 7) v v v v XC4 With heavy duty scraper v v v v XC5 Heat resistant cylinder ( 0 to 0 C) v v v v v XC6 Made of stainless steel ø3 to ø5 XC7 Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel v v v v XC8 djustable stroke cylinder/djustable extension type v v XC9 djustable stroke cylinder/djustable retraction type v v XC0 Dual stroke cylinder/double rod type v v XC Dual stroke cylinder/single rod type v v XC Tandem cylinder v v v v v v XC4 Change of trunnion bracket mounting position XC Fluororubber seal v v v v v XC6 With split pins for double clevis pin/double knuckle joint pin and flat washers ø5 XC7 Double clevis and double knuckle joint pins made of stainless steel Note 9) Note 9) Note 9) Note 9) Note 9) Note 9) Note 9) Note 9) XC9 Double knuckle joint with spring pin v v v v v v XC30 Rod trunnion v v v v XC35 With coil scraper v v v v XC65 Made of stainless steel (Combination of XC7 and XC68) v v v v v ø3 to ø5 XC68 Made of stainless steel (with hard chrome plated piston rod) v v v v XC88 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: Stainless steel 304) v v v v XC89 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: S45C) v v v v XC9 Spatter resistant coil scraper, Grease for welding (Piston rod: S45C) v v v v X84 Cylinder with heat resistant reed auto switch ( 0 to 0 C) v v v v v v v Note ) For details, refer to the Web Catalog. Note ) For details about the smooth cylinder, refer to the est Pneumatics No.w-3. Note 3) Simple specials except XC4 and XC4. Note 4) XC0 specification for the MK-Z series is the non-rotating type on both sides. For only one side, submit a special order request form. Note 5) Copper-free for the externally exposed part. For details, refer to the Web Catalog. 390

5 M Series Use the new series Smooth Cylinder MY Series to realize bi-directional low friction and low-speed operation. (Refer to the est Pneumatics No.w-3.) MK-Z (Non-rotating rod type) M Note 6) (With end lock) Double acting MY-Z Note ) MlQ Note 6) (Smooth Cylinder) (Low friction type) Single rod Double rod Single rod Single rod Single rod ir Rubber ir Rubber ir Note 9) est Pneumatics No.w-3 44 ø3 to ø00 Symbol V V V V V V V Standard v v v v v v v Long st V V V V V V V D V V V V V v v Ml-l J K v 5 v v Ml R V v v v v v v 0- v 0- v v Xl v v v v v v v X5 v v v v v X6 v v v v v X3 v v XC3 v XC4 v v v v v XC5 Note 8) Note 8) v v v v v XC6 Note 4) Note 4) v XC7 v v v XC8 v v v XC9 v v XC0 v v v v v XC v v v v v XC Note 3) v v XC4 v v v v v XC XC6 v v XC7 v v v v XC9 XC30 v v XC35 v XC65 XC68 XC88 XC89 XC9 v v v v v X84 Note 6) The cover shape is the same as the current product. Note 7) The XC3, XC3CC and XC3DD with trunnion bracket are available with new models (part numbers with Z ). Note 8) The piston rod of the MK-Z series is made of stainless steel. The rod end nut made of stainless steel is available with X9. Note 9) The copper and fluorine-free specification is available as a standard product. 39 CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS D- -X Technical Data

6 With auto switch With auto switch (uilt-in magnet) Port thread type Nil Rc TN NPT TF G M 3 MD 3 Mounting type 3 3 mm mm asic L xial foot mm F Rod flange mm G Head flange mm C Single clevis mm D Double clevis 5 5 mm T Center trunnion Trunnion type is mounted before shipment. Other mounting brackets ø3 to ø00: Shipped together. ø5: ssembled before shipment. ir Cylinder: Standard Type Double cting, Single Rod M Series ø3, ø40, ø50, ø63, ø80, ø00, ø Z Z ccessories Nil No bracket N Pivot bracket Only for D and T mounting types. Pivot bracket is shipped together with the product. For details, refer to page 400. Cylinder stroke Refer to Standard Strokes on page 393. How to Order Suffix (Cushion) Nil ir cushion N Rubber bumper Since the bumpers are attached to the both sides of the piston for rubber bumper type, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm. Suffix (Rod boot) Nil None J Nylon tarpaulin K Heat resistant tarpaulin M9W ccessories Nil No bracket V Single knuckle joint W Double knuckle joint RoHS Number of auto uto switch switches Nil Without auto switch Nil pcs. For applicable auto switches, S pc. refer to the table below. 3 3 pcs. n n pcs. Made to Order For details, refer to page 393. knuckle joint pin is not provided with the single knuckle joint. Rod end bracket is shipped together with the product. Refer to Ordering Example of Cylinder ssembly on page 393. pplicable uto Switches/Refer to the pages 575 to 70 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Electrical entry Indicator light Wiring (Output) Load voltage uto switch model Lead wire length [m] DC Pre-wired connector pplicable load -wire 4 V Terminal 33 conduit 34 PLC Yes 00 V, 00 V DIN terminal 44 Relay, Diagnostic indication (-color indicator) Grommet 59W V PLC Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. water resistant type cylinder is recommended for use in an environment which requires water resistance. Lead wire length symbols: 0.5 m Nil (Example) M9NW 3 m L (Example) M9NWL m M (Example) M9NWM 5 m Z (Example) M9NWZ Solid state auto switches marked with are produced upon receipt of order. Since there are other applicable auto switches than listed above, refer to page 43 for details. The D-9l/M9l/P3DWl auto switches are shipped together, (but not assembled). (However, auto switch mounting brackets are assembled for the D-9l/M9l before shipment.) 39 C Tie-rod mounting and mounting 3-wire (NPN) M9N V V V v v IC Grommet 3-wire (PNP) 4 V 5 V, V M9P V V V v v circuit -wire V M9 V V V v v Terminal 3-wire (NPN) 5 V, V G39 conduit -wire V K39 3-wire (NPN) M9NW V V V v v IC Diagnostic indication 5 V, V 3-wire (PNP) M9PW V V V v v circuit Relay, (-color indicator) Yes -wire V M9W V V V v v PLC 3-wire (NPN) 4 V M9N Water resistant 5 V, V v v V v v IC Grommet 3-wire (PNP) M9P circuit (-color indicator) v v V v v -wire V M9 v v V v v With diagnostic output (-color indicator) 4-wire (NPN) 5 V, V F59F V V v v IC circuit Magnetic field resistant -wire P3DW V V V v (-color indicator) (Non-polar) P4DW V V v 3-wire (NPN equivalent) 5 V 96 V V IC circuit Yes 00 V 93 V V V V Grommet No 00 V or less 90 V V IC circuit Relay, Yes 00 V, 00 V 54 V V V PLC 0.5 (Nil) (M) No V 00 V or less 64 V V 3 (L) 5 (Z)

7 ir Cylinder: Standard Type Double cting, Single Rod M Series Specifications Symbol Symbol Double acting Made to Order Click here for details Symbol Specifications -X Change of rod end shape -X5 Oversized rod cylinder * * *3 -X6 Heat resistant cylinder ( 0 to 50 C) -XC3 Special port location *3 -XC4 With heavy duty scraper -XC5 Heat resistant cylinder ( 0 to 0 C) -XC6 Made of stainless steel *4 -XC7 Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel -XC8 djustable stroke cylinder/djustable extension type -XC9 djustable stroke cylinder/djustable retraction type -XC0 Dual stroke cylinder/double rod type -XC Dual stroke cylinder/single rod type -XC Tandem cylinder -XC4 Change of trunnion bracket mounting position -XC Fluororubber seal -XC6 Made to Order: Individual Specifications (For details, refer to page 433.) Specifications -X84 Cylinder with heat resistant reed auto switch ( 0 to 0 C) With split pins for double clevis pin/double knuckle joint pin and flat washers *4 -XC7 Double clevis and double knuckle joint pins made of stainless steel -XC9 Double knuckle joint with spring pin -XC30 Rod trunnion -XC35 With coil scraper -XC65 Made of stainless steel (Combination of XC7 and XC68) * -XC68 Made of stainless steel (with hard chrome plated piston rod) * -XC88 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: Stainless steel 304) -XC89 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: S45C) -XC9 Spatter resistant coil scraper, Grease for welding (Piston rod: S45C) * ir cushion only * Except ø5 *3 The cover shape is the same as the current product. *4 ø5 only For special port location (-XC3), the mounting bracket and port location can be determined using the standard product corresponding to the operating conditions. lso, this is only applicable to -XC3, -XC3CC and -XC3DD with trunnion bracket. For parts made of stainless steel (-XC6), use the same specification stainless steel with the surface treatment (with hard chrome plated piston rod) (-XC68). ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Lubricant Piston speed Standard Strokes ore Standard stroke Max. manufacturable size Stroke range q Stroke range w stroke 3 5, 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500 Up to , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700, 800 Ordering Example of Cylinder ssembly Double knuckle joint uto switch Double clevis Pivot bracket Double acting, Single rod Up to 800 Up to , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700, 800, 900, 000 Up to 000 Note ) Manufacture of intermediate strokes is possible. (Spacers are not used.) Note ) pplicable strokes should be confirmed according to the usage. For details, refer to ir Cylinders Model Selection on front matter pages. In addition, the products that exceed the stroke range q might not be able to fulfill the specifications due to the deflection etc. Note 3) Please consult with SMC for manufacturability and the part numbers when exceeding the stroke range w. Note 4) The stroke range with rod boot is up to 000 mm. Please consult with SMC when exceeding 000 mm strokes. ir.5 MPa.0 MPa 0.05 MPa Without auto switch: 0 to 70 C (No freezing) With auto switch: 0 to 60 C Not required (Non-lube) 50 to 000 mm/s Stroke length tolerance Up to 50: +.0 0, 5 to 000: +.4 0, 00 to 500: +.8 0, 50 to 000: +. 0 Cushion ir cushion or Rubber bumper Port size (Rc) /8 /4 3/8 / Mounting asic, xial foot, Rod flange, Head flange Single clevis, Double clevis, Center trunnion Cylinder model: MDD3-50Z-NW-M9W Mounting D: Double clevis Pivot bracket N: Yes Rod end bracket W: Double knuckle joint uto switch D-M9W: pcs. * Pivot bracket, double knuckle joint and auto switch are shipped together with the product, but not assembled. Refer to pages 45 to 43 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range 393 CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS D- -X Technical Data

8 M Series ccessories Rod oot Material Standard Option Mounting asic xial foot Rod flange Head flange Single clevis Double clevis Center trunnion Rod end nut Clevis pin Single knuckle joint Double knuckle joint (with pin) Rod boot Refer to page 40 for dimensions and part numbers. (Refer to page 396 for rod boot.) Mounting rackets/part No. Symbol Material Max. ambient temp. J Nylon tarpaulin 70 C K Heat resistant tarpaulin 0 C Max. ambient temperature for rod boot itself. llowable Kinetic Energy xial foot Note ) M-L03 M-L04 M-L05 M-L06 M-L08 M-L0 M-L Rod/Head flange M-F03 M-F04 M-F05 M-F06 M-F08 M-F0 M-F Single clevis M-C03 M-C04 M-C05 M-C06 M-C08 M-C0 M-C Double clevis M-D03 M-D04 M-D05 M-D06 M-D08 M-D0 M-D Note ) Order two foots per cylinder. Note ) ccessories for each mounting bracket are as follows. xial foot, Rod/Head flange, Single clevis/ody mounting bolt; Double clevis/ody mounting bolt, Clevis pin, Flat washers and Split pins. Refer to page 40 for details. Theoretical Force Load mass [kg] ø5 ø00 ø80 ø63 ø50 ø40 ø3 (Unit: N) OUT IN 0 Rod diameter Operating Piston area direction [mm ] Operating pressure [MPa] OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN Note) Theoretical force [N] = Pressure [MPa] x Piston area [mm ] Maximum speed [mm/s] 000 Example) Load limit at rod end when the air cylinder ø63 is actuated at 500 mm/s. Extend upward from 500 mm/s on the horizontal axis of the graph to the intersection point with the line for a tube bore size of 63 mm, and then extend leftward from this point to find the load of 80 kg. Weights asic weight [kg] asic xial foot Rod/Head flange Single clevis Double clevis Center trunnion dditional weight per 50 mm of stroke ll mounting brackets ccessories 394 Single knuckle joint Double knuckle joint (with pin) Calculation Example) M3-00Z (asic, ø3, 00 stroke) asic weight 0.44 (asic, ø3) dditional weight 0./50 stroke Cylinder stroke 00 stroke x 00/50 = 0.66 kg

9 ir Cylinder: Standard Type Double cting, Single Rod M Series Construction!9!4 i q!!6! e r t!8 u w o!0!7 Component Parts No. Description Material Q ty Note Rod cover luminum die-cast Trivalent chromated Head cover luminum die-cast Trivalent chromated 3 Cylinder tube luminum alloy Hard anodized 4 Piston rod Carbon steel Hard chrome plating 5 Piston luminum alloy 6 Cushion ring luminum alloy nodized 7 Cushion ring luminum alloy nodized 8 ushing earing alloy 9 Cushion valve Steel wire Trivalent zinc chromated 0 Retaining ring Steel for spring ø40 to ø5 M5 No. Description Material Q ty Note Tie-rod Carbon steel 4 Trivalent zinc chromated Tie-rod nut Carbon steel 8 Trivalent zinc chromated 3 Wear ring Resin 4 Rod seal NR 5 Piston seal NR 6 Cushion seal Urethane 7 Cushion valve seal NR 8 Cylinder tube gasket NR 9 Rod end nut Rolled steel Trivalent zinc chromated 0 Magnet () CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS Replacement Parts/Seal Kit Kit no. 3 M3Z PS 40 C 40Z PS 50 C 50Z PS 63 C 63Z PS 80 C 80Z PS 00 C 00Z PS 5 M5 PS Contents Set of the nos.!4,!5,!6,!8 Seal kits consist of items!4,!5,!6,!8, and can be ordered by using the seal kit number corresponding to each bore size. Center trunnion type should not be disassembled. (Refer to page 434.) The seal kit includes a grease pack (0 g for ø3 to ø50, 0 g for ø63 and ø80, 30 g for ø00 and ø5). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-00 (0 g), GR-S-00 (0 g) Water Resistant ir Cylinder Water resistant air cylinders are also available in the M series, which are suitable for use on machine tools, where exposure to coolant is possible and applicable for food machinery and automobile washing equipment in an environment where water splashes. Please refer to page 5 for more information. 395 D- -X Technical Data

10 M Series Standard asic: () Width across flats K G x Rc P When the stroke is 0 mm or longer, a tie-rod reinforcement ring is attached. G Cushion valve W V Port øe øe ød TX C MM Width across flats H L K H M F M N x 4 x J ZZ + Stroke TT S + Stroke N C TY With rod boot ød øe h l f L C D E F G H H J K K M M MM N P S TT TX TY V W ZZ M6 x M0 x.5 7 / M6 x M4 x.5 7 / M8 x M8 x / M8 x M8 x / M0 x M x / M0 x M6 x.5 38 / M x M7 x 38 / With Rod oot l d e f to 50 5 to 00 0 to 50 5 to 00 0 to to to to to to to to h to 50 5 to 00 0 to 50 5 to 00 0 to to to to to to to to Rubber umper S ZZ Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm 396

11 ir Cylinder: Standard Type Double cting, Single Rod M Series Standard/With Mounting racket Refer to asic () for other dimensions. xial foot: (L) When the stroke is 0 mm or longer, a tie-rod reinforcement ring is attached. Cushion valve TY Port CJ TX 4 x øld LH LY CJP CJ LT Y X TT LS + Stroke ZZ + Stroke LD LH LS LT LX LY LZ TT TX TY X Y ZZ X Y Rubber umper LS ZZ LX LZ JCM CM CM3 CG CG3 JM M M Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm C CS CS Rod flange: (F) TX FE FT When the stroke is 0 mm or longer, a tie-rod reinforcement ring is attached. Cushion valve Port 4 x øfd øfd FY F TT F FD FE FT FX FY FZ Fd TT TX TY Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm TY FX FZ 397 D- -X Technical Data

12 M Series Standard/With Mounting racket Head flange: (G) When the stroke is 0 mm or longer, a tie-rod reinforcement ring is attached. Refer to asic () for other dimensions. Cushion valve Port 4 x øfd TX TX FY F TT ZZ + Stroke F FD FT FX FY FZ TT TX TY ZZ FT Rubber umper ZZ TY FX FZ Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm Single clevis: (C) When the stroke is 0 mm or longer, a tie-rod reinforcement ring is attached. Cushion valve Port CDH0 TT Z + Stroke ZZ + Stroke U L RR CX TY CDH0 CX L RR TT TX TY U Z ZZ Rubber umper Z ZZ Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm 398

13 ir Cylinder: Standard Type Double cting, Single Rod M Series Standard/With Mounting racket Double clevis: (D) Cushion valve Refer to asic () for other dimensions. Port TT Z + Stroke ZZ + Stroke Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm TX U L CDH0 CDd9 CX CZ L RR TT TX TY U Z ZZ Hole dia.: CDH0 Shaft dia.: CDd9 RR Rubber umper Z ZZ CX CZ TY CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS Center trunnion: (T) Z + / stroke Cushion valve Port TY TDe8 TT TX TY TZ Z TT Rubber umper Z TX TZ øtde8 D- Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the Z dimension is longer than the cylinder with air cushion as follows: ø3, ø40: +3 mm, ø50, ø63: +4 mm, ø80, ø00: +5 mm, ø5: +6 mm 399 -X Technical Data

14 M Series Pivot racket/trunnion and Double Clevis Pivot racket Part No. Description Ml3 Ml40 Ml50 Ml63 Ml80 Ml00 Ml5 Trunnion pivot bracket Note) M-S03 M-S04 M-S06 M-S0 M-S Double clevis pivot bracket M-03 M-05 M-08 M- Note) Order trunnion pivot brackets per cylinder. Trunnion pivot bracket Z + / stroke TO TE TX TO 4 x øtt TF TH øtd TY TU TL T x øtr TU Part no. T TL TU TC TX TE TO TR TT TS TH TF Z TDH0 M-S M-S M-S M-S M-S TS TC Rubber umper Z Double clevis pivot bracket 90 Z + Stroke D DD 4 x ødt DX DH DS DU DL D 4 x ødr DU Part no. D D DL DU DC DX DE DO DR DT DS DH Z DD H0 M M M M DO DC DE Rubber umper Z DO Rotating ngle , , , Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the Z dimension is longer than the cylinder with air cushion as follows: ø3, ø40: +3 mm, ø50, ø63: +4 mm, ø80, ø00: +5 mm, ø5: +6 mm Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm

15 ir Cylinder: Standard Type Double cting, Single Rod M Series Dimensions of ccessories Rod end nut (Standard) 30 d Knuckle joint pin Clevis pin x ød ødd9 Part no. I type Single knuckle joint H D MM NDH0 øe L U C d H C D NT-03 3 M0 x NT M4 x NT-05 50, 63 M8 x NT M x NT-0 00 M6 x NT-M 5 M7 x Y type Double knuckle joint 45 MM øndh0 RR NX 0.0 Part no. E L MM R U NDH0 NX I-03M M0 x I-04M M4 x I-05M 50, M8 x I-08M M x I-0M M6 x I-M M7 x racket Combinations racket combination available Refer to the figure below. racket for cylinder racket for workpiece Single clevis Double clevis Single knuckle joint Double knuckle joint m l L Part no. Dd9 L l m d pplicable Clevis Knuckle (Drill through) split pin CD-M03 Note ) 3, ø3 x 8 l CD-M05 Note ) 50, ø4 x 5 l CD-M08 Note ) 80, ø4 x 35 l IY- Note ) ø4 x 40 l Note ) Split pins and flat washers are included. Note ) Only pins are included when shipped. øe U L Part no. E L MM R U NDH0 NX NZ Y-03M Note ) M0 x Y-04M Note ) M4 x Y-05M Note ) 50, M8 x Y-08M Note ) M x Y-0M Note ) M6 x Y-M Note ) M7 x Note ) pin, split pins and flat washers are included. Note ) pin and split pins are included. Clevis pivot bracket Single clevis q w Double clevis e r o Single knuckle joint t y Double knuckle joint u i!0 RR NX NZ CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS No. ppearance No. ppearance Single clevis + Double clevis Single knuckle joint + Double knuckle joint q y Single clevis + Double knuckle joint Double knuckle joint + Single clevis w u Double clevis + Single clevis Double knuckle joint + Single knuckle joint e i Double clevis + Single knuckle joint Double clevis + Clevis pivot bracket r o t Single knuckle joint + Double clevis!0 Double knuckle joint + Clevis pivot bracket 40 D- -X Technical Data

16 ir Cylinder: Standard Type Double cting, Double Rod MW Series ø3, ø40, ø50, ø63, ø80, ø00, ø5 RoHS How to Order MW L 3 50 Z With auto switch MDW L 3 50 Z M9W With auto switch (uilt-in magnet) Mounting type asic L xial foot F Rod flange T Center trunnion * Trunnion type is mounted before shipment. * Other mounting brackets ø3 to ø00: Shipped together. ø5: ssembled before shipment. 3 3 mm mm mm mm mm mm 5 5 mm Port thread type Nil Rc TN NPT TF G Cylinder stroke Refer to Standard Strokes on page 403. uto switch Nil Without auto switch * For applicable auto switches, refer to the table below. Suffix (Rod boot) Nil None J Nylon tarpaulin (one end) JJ Nylon tarpaulin (both ends) K Heat resistant tarpaulin (one end) KK Heat resistant tarpaulin (both ends) Number of auto switches Nil pcs. S pc. 3 3 pcs. n n pcs. Made to Order For details, refer to page 403. Suffix (Cushion) Nil ir cushion N* Rubber bumper * Since the bumpers are attached to the both sides of the piston for rubber bumper type, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm. pplicable uto Switches/Refer to pages 575 to 70 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Electrical entry Indicator light Wiring (Output) Load voltage uto switch model Lead wire length [m] DC Pre-wired connector pplicable load DIN terminal 44 Relay, Diagnostic indication (-color indicator) Grommet 59W PLC * Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please contact SMC regarding water resistant types with the above model numbers. * Lead wire length symbols: 0.5 m Nil (Example) M9NW 3 m L (Example) M9NWL m M (Example) M9NWM 5 m Z (Example) M9NWZ * Solid state auto switches marked with p are produced upon receipt of order. * Since there are other applicable auto switches than listed above, refer to page 43 for details. * The D-9l/M9l/P3DWl auto switches are shipped together, (but not assembled). (However, auto switch mounting brackets are assembled for the D-9l/M9l before shipment.) 40 C Tie-rod mounting and mounting 3-wire (NPN) M9N V v v Grommet 3-wire (PNP) 4 V 5 V, V M9P v v IC circuit -wire V M9 v v Terminal 3-wire (NPN) 5 V, V G39 conduit -wire V K39 3-wire (NPN) M9NW v v Diagnostic indication 5 V, V IC circuit 3-wire (PNP) M9PW v v Relay, (-color indicator) Yes -wire V M9W v v PLC 3-wire (NPN) 4 V M9N Water resistant 5 V, V v v v v Grommet 3-wire (PNP) M9P (-color indicator) v v v v IC circuit -wire V M9 * v v v v Diagnostic output (-color indicator) 4-wire (NPN) 5 V, V F59F v v IC circuit Magnetic field resistant -wire P3DW v (-color indicator) (Non-polar) P4DW v 3-wire Yes (Equiv. to NPN) 5 V 96 IC circuit Grommet 00 V 93 No 00 V or less 90 IC circuit Yes 00 V, 00 V 54 Terminal conduit Relay, PLC No V 00 V or less 64 -wire 4 V PLC Yes 00 V, 00 V 0.5 (Nil) (M) 3 (L) 5 (Z)

17 ir Cylinder: Standard Type Double cting, Double Rod MW Series Specifications Symbol Double acting, ir cushion Symbol Made to Order Click here for details Specifications -Xl Change of rod end shape -X6 Heat resistant cylinder ( 0 to 50 C) -XC3 Special port location * * -XC4 With heavy duty scraper -XC5 Heat resistant cylinder ( 0 to 0 C) -XC6 Made of stainless steel * -XC7 Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel -XC4 Change of trunnion bracket mounting position -XC Fluororubber seal -XC30 Rod trunnion -XC35 With coil scraper -XC68 Made of stainless steel (with hard chrome plated piston rod) *3 -XC88 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: Stainless steel 304) -XC89 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: S45C) -XC9 Spatter resistant coil scraper, Grease for welding (Piston rod: S45C) * The cover shape is the same as the current product. * ø5 only *3 Except ø5 For special port location (-XC3), the mounting bracket and port location can be determined using the standard product corresponding to the operating conditions. lso, this is only applicable to -XC3, -XC3CC and -XC3DD with trunnion bracket. For parts made of stainless steel (-XC6), use the same specification stainless steel with the surface treatment (with hard chrome plated piston rod) (-XC68). Refer to pages 45 to 43 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Water Resistant ir Cylinder Water resistant air cylinders are also available in the M series, which are suitable for use on machine tools in an atmosphere with coolant and applicable to food machinery and automobile washing equipment in an environment with water splashes. Please refer to page 5 for more information. ction Fluid Proof pressure Max. operating pressure Double acting, Double rod ir.5 MPa.0 MPa Min. operating pressure 0.05 MPa mbient and fluid Without auto switch: 0 to 70 C (No freezing) temperature With auto switch: 0 to 60 C Lubrication Not required (Non-lube) Operating piston speed 50 to 000 mm/s 50 to 700 mm/s llowable stroke tolerance Up to 50: +.0 0, 5 to 000: +.4 0, 00 to 500 Cushion Note) ir cushion or Rubber bumper Port size (Rc, NPT, G) /8 /4 3/8 / Mounting asic, xial foot, Rod flange, Center trunnion Note) Kinetic energy absorbable by the cushion mechanism is identical to double acting, single rod. Standard Strokes ore size Rod oot Material Symbol Material Max. ambient temp. J Nylon tarpaulin 70 C K Heat resistant tarpaulin 0 C * * Max. ambient temperature for rod boot itself. Mounting rackets/part No. * Order two foots per cylinder. Standard stroke Stroke range q 3 5, 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700, 800 Max. manufacturable Stroke range w stroke Up to 000 Up to , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700, 800 Up to , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700, 800, 900, 000 Note ) Manufacture of intermediate strokes is possible. (Spacers are not used.) Note ) pplicable strokes should be confirmed according to the usage. For details, refer to ir Cylinders Model Selection on front matter pages. In addition, the products that exceed the stroke range q might not be able to fulfill the specifications due to the deflection etc. Note 3) Please consult with SMC for manufacturability and the part numbers when exceeding the stroke range w. Note 4) The stroke range with rod boot is up to 000 mm. Please consult with SMC when exceeding 000 mm strokes. ccessories Mounting asic xial foot Rod flange Up to 800 Center trunnion Standard Rod end nut Option Single knuckle joint Double knuckle joint (with pin) Rod boot * Refer to page 40 for dimensions and part numbers. (Refer to page 406 for rod boot.) xial foot M-L03 M-L04 M-L05 M-L06 M-L08 M-L0 M-L Rod flange M-F03 M-F04 M-F05 M-F06 M-F08 M-F0 M-F 403 CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS D- -X Technical Data

18 MW Series Theoretical Force (Unit: N) OUT IN Rod diameter Operating direction Piston area [mm ] Note) Theoretical force [N] = Pressure [MPa] x Piston area [mm ] Operating pressure [MPa] IN, OUT IN, OUT IN, OUT IN, OUT IN, OUT IN, OUT IN, OUT Weights/luminum Tube asic weight asic xial foot Rod flange Center trunnion dditional weight per 50 mm of stroke ll mounting brackets ccessories Calculation Example) MW3-00Z (asic, ø3, 00 stroke) asic weight 0.56 (asic, ø3) dditional weight 0.5/50 stroke Cylinder stroke 00 stroke x 00/50 = 0.86 kg Single knuckle joint Double knuckle joint (with pin) [kg] 404

19 ir Cylinder: Standard Type Double cting, Double Rod MW Series Construction u i!4!6! y q!0!3 o w e t!!7 r!5 ø3 MW5 Component Parts No. Description Material Q ty Note No. Description Material Q ty Note Rod cover luminum die-cast Trivalent chromated 0 Tie-rod nut Carbon steel 8 Trivalent zinc chromated Cylinder tube luminum alloy Hard anodized Rod seal NR 3 Piston rod Carbon steel Hard chrome plating Piston seal NR 4 Piston luminum alloy 3 Cushion seal Urethane 5 Cushion ring luminum alloy nodized 4 Cushion valve seal NR 6 ushing earing alloy 5 Cylinder tube gasket NR 7 Cushion valve Steel wire Trivalent zinc chromated 6 Rod end nut Rolled steel Trivalent zinc chromated 8 Retaining ring Steel for spring ø40 to ø5 7 Magnet () 9 Tie-rod Carbon steel 4 Trivalent zinc chromated CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS Replacement Parts/Seal Kit Kit no. 3 MW3Z PS 40 CW40Z PS 50 CW50Z PS 63 CW63Z PS 80 CW80Z PS 00 CW00Z PS 5 MW5 PS Contents Set of the nos.!,!,!3,!5 Seal kits consist of items!,!,!3,!5, and can be ordered by using the seal kit number corresponding to each bore size. Trunnion type should not be disassembled. (Refer to page 434.) The seal kit includes a grease pack (0 g for ø3 to ø50, 0 g for ø63 and ø80, 30 g for ø00 and ø5). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-00 (0 g), GR-S-00 (0 g) 405 D- -X Technical Data

20 MW Series Standard asic: () Width across flats K G x Rc P G Width across flats K V Port W Cushion valve øe øe ød ød øe Width across flats MM K H M H L M L x 4 x J F N N F K H S + Stroke H + Stroke ZZ + x Stroke MM Width across flats C ød øe C With rod boot Width across flats K ød øe ød l f h G x Rc P Note) ZZ indicates dimensions for double side rod boot. ZZ Note) to 5 to 0 to 5 to 0 to 30 to 40 to 50 to 60 to 70 to 80 to 90 to G Width across flats K ød øe ød MM H H MM Width across L L Width across flats K l f N N f l + Stroke K flats h S + Stroke h + Stroke ZZ + x Stroke L C D E F G H H J K K M M MM N P S V W ZZ M6 x M0 x.5 7 / M6 x M4 x.5 7 / M8 x M8 x / M8 x M8 x / M0 x M x / M0 x M6 x.5 38 / M x M7 x.0 38 / With Rod oot l h d e f to 50 5 to 00 0 to 50 5 to 00 0 to to to to to to to 90 to to to 00 0 to 50 5 to 00 0 to to to to to to to 90 to Rubber umper Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm S ZZ

21 ir Cylinder: Standard Type Double cting, Double Rod MW Series Standard/With Mounting racket xial foot: (L) Refer to asic () for other dimensions and with rod boot. Port Cushion valve CJ LH LY CJP LT Y X LS + Stroke X 4 x øld Y LX LZ CJ JCM Rod flange: (F) FT X Y LD LH LS LT LX LY LZ Port Cushion valve 4 x øfd CM CM3 CG CG3 JM M M øfd Port Cushion valve TY øtde8 FY F C FX FZ CS CS Center trunnion: (T) F FD FT FX FY FZ Fd Z + / stroke TT Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm, ø5: + mm Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the Z dimension is longer than the cylinder with air cushion as follows: ø3, ø40: +3 mm, ø50, ø63: +4 mm, ø80, ø00: +5 mm, ø5: +6 mm (For trunnion mounting) TX TZ TDe8 TT TX TY TZ Z D- -X Technical Data

22 ir Cylinder: Non-rotating Rod Type Double cting, Single Rod MK Series ø3, ø40, ø50, ø63, ø80, ø00 RoHS How to Order MK 3 50 Z With auto switch MDK 3 50 Z M9W With auto switch (uilt-in magnet) Mounting type asic/without bracket L xial foot F Rod flange G Head flange C Single clevis D Double clevis T Center trunnion * Mounting brackets other than trunnion type are shipped together. Port thread type Nil Rc TN NPT TF G 3 3 mm mm mm mm mm mm Cylinder stroke Refer to Standard Strokes on page 409. ccessories Nil No bracket N Pivot bracket * Only for D and T mounting types. * Pivot bracket is shipped together with the product. * For details, refer to page 400. Suffix (Cushion) Nil ir cushion N* Rubber bumper * Since the bumpers are attached to the both sides of the piston for rubber bumper type, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm. Suffix (Rod boot) Nil None J Nylon tarpaulin K Heat resistant tarpaulin uto switch Nil Without auto switch * For applicable auto switches, refer to the table below. Number of auto switches Nil pcs. S pc. 3 3 pcs. n n pcs. Made to Order For details, refer to page 409. ccessories Nil No bracket V Single knuckle joint W Double knuckle joint * knuckle joint pin is not provided with the single knuckle joint. * Rod end bracket is shipped together with the product. * The screw-in amount of the piston rod end cannot be adjusted when a clevis bracket, trunnion bracket and knuckle joint are used together. pplicable uto Switches/Refer to pages 575 to 70 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Electrical entry Indicator light Wiring (Output) Load voltage uto switch model Lead wire length [m] DC Pre-wired connector pplicable load -wire 4 V Terminal 33 conduit 34 PLC Yes 00 V, 00 V DIN terminal 44 Relay, Diagnostic indication (-color indicator) Grommet 59W V V PLC * Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. water resistant type cylinder is recommended for use in an environment which requires water resistance. * Lead wire length symbols: 0.5 m Nil (Example) M9NW 3 m L (Example) M9NWL m M (Example) M9NWM 5 m Z (Example) M9NWZ * Solid state auto switches marked with p are produced upon receipt of order. * Since there are other applicable auto switches than listed above, refer to page 43 for details. * The D-9l/M9l/P3DWl auto switches are shipped together, (but not assembled). (However, auto switch mounting brackets are assembled for the D-9l/M9l before shipment.) 408 C Tie-rod mounting and mounting 3-wire (NPN) M9N V V V v v Grommet 3-wire (PNP) 4 V 5 V, V M9P V V V v v IC circuit -wire V M9 V V V v v Terminal 3-wire (NPN) 5 V, V G39 conduit -wire V K39 3-wire (NPN) M9NW V V V v v Diagnostic indication 5 V, V IC circuit 3-wire (PNP) M9PW V V V v v Relay, (-color indicator) Yes -wire V M9W V V V v v PLC 3-wire (NPN) 4 V M9N Water resistant 5 V, V v v V v v Grommet 3-wire (PNP) M9P (-color indicator) v v V v v IC circuit -wire V M9 * v v V v v Diagnostic output (-color indicator) 4-wire (NPN) 5 V, V F59F V V v v IC circuit Magnetic field resistant -wire P3DW V V V v (-color indicator) (Non-polar) P4DW V V v 3-wire (Equiv. to NPN) 5 V 96 V V IC circuit Yes 00 V 93 V V V V Grommet No 00 V or less 90 V V IC circuit Relay, Yes 00 V, 00 V 54 V V V PLC 0.5 (Nil) (M) No V 00 V or less 64 V V 3 (L) 5 (Z)

23 ir Cylinder: Non-rotating Rod Type Double cting, Single Rod MK Series Specifications Symbol Symbol Double acting, ir cushion Made to Order Click here for details Specifications -X Change of rod end shape -XC3 Special port location * Tie-rod, cushion valve, tie-rod nut, etc. -XC7 made of stainless steel -XC8 djustable stroke cylinder/djustable extension type -XC9 djustable stroke cylinder/djustable retraction type -XC0 Dual stroke cylinder/double rod type -XC4 Change of trunnion bracket mounting position Double clevis and double knuckle joint -XC7 pins made of stainless steel -XC30 Rod trunnion * The cover shape is the same as the current product. For special port location (-XC3), the mounting bracket and port location can be determined using the standard product corresponding to the operating conditions. lso, this is only applicable to -XC3, -XC3CC and -XC3DD with trunnion bracket. ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Lubricant Piston speed Double acting, Single rod ir.5 MPa.0 MPa 0.05 MPa Without auto switch: 0 to 70 C (No freezing) With auto switch: 0 to 60 C Non-lube 50 to 000 mm/s Stroke length tolerance Up to 50: +.0 0, 5 to 000: +.4 0, 00 to 500: Cushion Note) ir cushion or Rubber bumper Port size (Rc, NPT, G) /8 /4 3/8 / Mounting asic, xial foot, Rod flange, Head flange, Single clevis, Double clevis, Center trunnion Non-rotating accuracy ±0.5 ±0.5 ±0.3 llowable rotating torque N m or less Note) Kinetic energy absorbable by the cushion mechanism is identical to double acting single rod. Standard Strokes Standard stroke 3 5, 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700 Manufacture of intermediate strokes is possible. (Spacers are not used.) ccessories Standard Option Mounting asic xial foot Rod flange Head flange Single clevis Double clevis Center trunnion Rod end nut V V V V V V V Clevis pin V Single knuckle joint V V V V V V V Double knuckle joint (with pin) V V V V V V V Rod boot V V V V V V V * Refer to page 40 for dimensions and part numbers. (Refer to page 396 for rod boot.) CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS Refer to pages 45 to 43 for cylinders with auto switches. Rod oot Material uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Symbol Material Max. ambient temp. J Nylon tarpaulin 70 C K Heat resistant tarpaulin 0 C * * Max. ambient temperature for rod boot itself. 409 D- -X Technical Data

24 MK Series Mounting rackets/part No xial foot Note ) M-L03 M-L04 M-L05 M-L06 M-L08 M-L0 Rod/Head flange M-F03 M-F04 M-F05 M-F06 M-F08 M-F0 Single clevis M-C03 M-C04 M-C05 M-C06 M-C08 M-C0 Double clevis M-D03 M-D04 M-D05 M-D06 M-D08 M-D0 Note ) Order two foots per cylinder. Note ) ccessories for each mounting bracket are as follows. xial foot, Rod/Head flange, Single clevis/ody mounting bolt; Double clevis/ody mounting bolt, Clevis pin, Flat washers and Split pins. Refer to page 40 for details. Theoretical Force OUT side is identical to double acting single rod. Refer to the table below for IN side. Piston area [mm ] Theoretical force [N] = Pressure [MPa] x Piston area [mm ] Weights asic weight [kg] asic xial foot Rod/Head flange Single clevis Double clevis Center trunnion dditional weight per 50 mm of stroke ll mounting brackets ccessories Calculation Example) MK3-00Z (asic, ø3, 00 stroke) asic weight 0.47 (asic, ø3) dditional weight 0./50 stroke Cylinder stroke 00 stroke x 00/50 = 0.7 kg Single knuckle joint Double knuckle joint (with pin)

25 ir Cylinder: Non-rotating Rod Type Double cting, Single Rod MK Series Construction!9!4 q!!6! e r t!8 w u o!0!7 Width across flats Rod view Component Parts ø3 (:) No. Description Material Q ty Note Rod cover luminum die-casted Trivalent chromated Head cover luminum die-casted Trivalent chromated 3 Cylinder tube luminum alloy Hard anodized 4 Piston rod Stainless steel 5 Piston luminum alloy 6 Cushion ring Rolled steel Zinc chromated 7 Piston nut Rolled steel Zinc chromated 8 Non-rotating guide earing alloy 9 Cushion valve Steel wire Trivalent zinc chromated 0 Retaining ring Spring steel ø40 to ø00 Tie-rod Carbon steel 4 Trivalent zinc chromated Replacement Parts/Seal Kit Kit no. Contents 3 MK3Z PS 40 MK40Z PS 50 MK50Z PS Set of the nos. 63 MK63Z PS!4,!5,!6,!8 80 MK80Z PS 00 MK00Z PS ø3 No. Description Material Q ty Note Tie-rod nut Carbon steel 8 Trivalent zinc chromated 3 Wear ring Resin 4 * Rod seal NR 5 * Piston seal NR 6 * Cushion seal Urethane 7 Cushion valve seal NR 8 * Cylinder tube gasket NR 9 Rod end nut Rolled steel Trivalent zinc chromated 0 Magnet () Hexagon socket head set screw Steel wire Trivalent black zinc chromated * Seal kits consist of items!4,!5,!6,!8, and can be ordered by using the seal kit number corresponding to each bore size. * Seal kit includes a grease pack (ø3 to 50: 0 g, ø63, 80: 0 g, ø00: 30 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-00 (0 g), GR-S-00 (0 g) * Model without air cushion is designed to include rubber bumpers. The overall length is longer than the cylinder with air cushion as follows because the bumpers are attached to the both sides of the piston; ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS Without Mounting racket asic: () G x Rc P G Cushion valve W V Port øe D øe MM C Section -' Width across flats ' H M L M F N H x 4 x J ZZ + Stroke S + Stroke L C D E F G H H J M M MM N P S V W ZZ M6 x 6 4 M0 x.5 7 / M6 x 6 4 M4 x.5 7 / M8 x M8 x / M8 x M8 x / M0 x M x / M0 x M6 x.5 38 / The dimensions for each mounting type and the dimensions with rod boot are the same as those for standard model (double acting, single rod). N C 4 D- -X Technical Data

26 ir Cylinder: Non-rotating Rod Type Double cting, Double Rod MKW Series ø3, ø40, ø50, ø63, ø80, ø00 RoHS With auto switch With auto switch (uilt-in magnet) Mounting type asic/without bracket L xial foot F Rod flange T Center trunnion * Mounting brackets other than trunnion type are shipped together. MKW MDKW 3 3 mm mm mm mm mm mm L L 3 3 Port thread type Nil Rc TN NPT TF G How to Order Cylinder stroke Refer to Standard Strokes on page Z Z uto switch Nil M9W Without auto switch * For applicable auto switches, refer to the table below. Suffix (Rod boot) Nil None J Nylon tarpaulin (one end) JJ Nylon tarpaulin (both ends) K Heat resistant tarpaulin (one end) KK Heat resistant tarpaulin (both ends) Number of auto switches Nil pcs. S pc. 3 3 pcs. n n pcs. Made to Order For details, refer to page 43. Suffix (Cushion) Nil ir cushion N* Rubber bumper * Since the bumpers are attached to the both sides of the piston for rubber bumper type, the overall length is longer than the cylinder with air cushion as follows: ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm. pplicable uto Switches/Refer to pages 575 to 70 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Electrical entry Indicator light Wiring (Output) Load voltage uto switch model Lead wire length [m] DC C Tie-rod mounting Pre-wired connector and mounting (Nil) (M) (L) (Z) M9N V V V v v pplicable load 3-wire (NPN) Grommet 3-wire (PNP) 4 V 5 V, V M9P V V V v v IC circuit -wire V M9 V V V v v Terminal 3-wire (NPN) 5 V, V G39 conduit -wire V K39 3-wire (NPN) M9NW V V V v v Diagnostic indication 5 V, V IC circuit 3-wire (PNP) M9PW V V V v v Relay, (-color indicator) Yes -wire V M9W V V V v v PLC 3-wire (NPN) 4 V M9N Water resistant 5 V, V v v V v v Grommet 3-wire (PNP) M9P (-color indicator) v v V v v IC circuit -wire V M9 * v v V v v Diagnostic output (-color indicator) 4-wire (NPN) 5 V, V F59F V V v v IC circuit Magnetic field resistant -wire P3DW V V V v (-color indicator) (Non-polar) P4DW V V v 3-wire Yes (Equiv. to NPN) 5 V 96 V V IC circuit Grommet 00 V 93 V V V V Terminal conduit No 00 V or less 90 V V IC circuit Yes 00 V, 00 V 54 V V V Relay, PLC No V 00 V or less 64 V V -wire 4 V PLC Yes 00 V, 00 V DIN terminal 44 Relay, Diagnostic indication (-color indicator) Grommet 59W V V PLC * Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please contact SMC regarding water resistant types with the above model numbers. * Lead wire length symbols: 0.5 m Nil (Example) M9NW 3 m L (Example) M9NWL m M (Example) M9NWM 5 m Z (Example) M9NWZ * Solid state auto switches marked with v are produced upon receipt of order. * Since there are other applicable auto switches than listed above, refer to page 43 for details. * The D-9l/M9l/P3DWl auto switches are shipped together, (but not assembled). (However, auto switch mounting brackets are assembled for the D-9l/M9l before shipment.) 4

27 ir Cylinder: Non-rotating Rod Type Double cting, Double Rod MKW Series Specifications Symbol Symbol Double acting Made to Order Click here for details Specifications -XC3 Special port location * Tie-rod, cushion valve, tie-rod nut, etc. -XC7 made of stainless steel -XC30 Rod trunnion * The cover shape is the same as the current product. For special port location (-XC3), the mounting bracket and port location can be determined using the standard product corresponding to the operating conditions. lso, this is only applicable to -XC3, -XC3CC and -XC3DD with trunnion bracket. ction Fluid Proof pressure Max. operating pressure Min. operating pressure mbient and fluid temperature Lubrication Operating piston speed Double acting, Double rod Note) Kinetic energy absorbable by cushion mechanism is identical to double acting single rod. ir.5 MPa.0 MPa 0.05 MPa Without auto switch: 0 to 70 C (No freezing) With auto switch: 0 to 60 C Non-lube 50 to 000 mm/s llowable stroke tolerance Up to 50: +.0 0, 5 to 800: Cushion Note) ir cushion or Rubber bumper Port size (Rc, NPT, G) /8 /4 3/8 / Mounting asic, xial foot, Rod flange, Center trunnion Non-rotating accuracy ±0.5 ±0.5 ±0.3 llowable rotating torque N m or less Standard Strokes Standard stroke 3 5, 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700 Manufacture of intermediate strokes is possible. (Spacers are not used.) ccessories Mounting asic xial foot Rod flange Center trunnion Standard Rod end nut V V V V Option Single knuckle joint V V V V Double knuckle joint (with pin) V V V V Rod boot V V V V * Refer to page 40 for dimensions and part numbers. (Except rod boot) CJ CJP CJ JCM CM CM3 CG CG3 JM M M C CS CS Rod oot Material Refer to pages 45 to 43 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Symbol Material Max. ambient temp. J Nylon tarpaulin 70 C K Heat resistant tarpaulin 0 C* * Max. ambient temperature for rod boot itself. Mounting rackets/part No xial foot M-L03 M-L04 M-L05 M-L06 M-L08 M-L0 Rod flange M-F03 M-F04 M-F05 M-F06 M-F08 M-F0 Note) Order two foots per cylinder. 43 D- -X Technical Data

28 MKW Series Theoretical Force Weights/luminum Tube Construction (Unit: N) Note) Theoretical force [N] = Pressure [MPa] x Piston area [mm ] asic weight OUT IN Rod dia. Operating Piston area Operating pressure [MPa] Width across flats direction [mm ] OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN asic xial foot Rod flange Center trunnion dditional weight per 50 mm of stroke ll mounting brackets ccessories Single knuckle joint Double knuckle joint (with pin) Calculation Example) MKW3-00Z (asic, ø3, 00 st) asic weight 0.56 (asic, ø3) dditional weight 0.6/50 stroke x 00/50 = 0.88 kg!7-7-!9 -!!4!0 w e y!3!8 t! r i o!5 [kg] Width across flats Rod view ø3 (:) Component Parts No. Description Material Q ty Note - Rod cover luminum die-casted Non-rotating rod - Rod cover luminum die-casted Standard Cylinder tube luminum alloy Hard anodized 3 Piston rod Stainless steel Non-rotating rod 4 Piston rod Carbon steel Standard 5 Piston luminum alloy 6 Cushion ring Rolled steel Zinc chromated 7- Non-rotating guide earing alloy Non-rotating rod 7- ushing earing alloy Standard 8 Cushion valve Steel wire Trivalent zinc chromated 9 Retaining ring Spring steel ø40 to ø00 0 Tie-rod Carbon steel 4 Trivalent zinc chromated Tie-rod nut Carbon steel 8 Trivalent zinc chromated -* Rod seal NR Non-rotating rod -* Rod seal NR Standard 3* Piston seal NR 4* Cushion seal Urethane 5 Cushion valve seal NR 6* Cylinder tube gasket NR 44 No. Description Material Q ty Note 7 Rod end nut Rolled steel Trivalent zinc chromated 8 Magnet () 9 Hexagon socket head set screw Steel wire Trivalent black zinc chromated Replacement Parts/Seal Kit Kit no. 3 MKW3Z PS 40 MKW40Z PS 50 MKW50Z PS 63 MKW63Z PS 80 MKW80Z PS Contents Set of the nos.!,!3,!4,!6 00 MKW00Z PS * Seal kits consist of items!,!3,!4,!6, and can be ordered by using the seal kit number corresponding to each bore size. * Trunnion type should not be disassembled. (Refer to page 434.) * Seal kit includes a grease pack (ø3 to 50: 0 g, ø63, 80: 0 g, ø00: 30 g). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S-00 (0 g), GR-S-00 (0 g)

29 ir Cylinder: Non-rotating Rod Type Double cting, Double Rod MKW Series Standard asic: () G x Rc P G Cushion valve Port V W Q Width across flats K øe CJ K øe MM MM ød øe C CJP Section Q-Q Width across flats Q H L H M F M N x 4 x J S + Stroke ZZ + x Stroke N F H L K H + Stroke Width across flats C CJ JCM CM CM3 CG Positional relationship between port and cushion valve CG3 Port JM M M Cushion valve C CS CS L C D E F G H H J K K K M6 x M6 x M8 x M8 x M0 x M0 x M M MM N P S* V W ZZ* M0 x.5 7 / M4 x.5 7 / M8 x / M8 x / M x / M6 x.5 38 / * Model without air cushion is designed to include rubber bumpers. The overall length is longer than the cylinder with air cushion as follows because the bumpers are attached to the both sides of the piston; ø3, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø00: +0 mm The dimensions for each mounting type are the same as those for standard model (double acting, double rod). Refer to pages 406 and D- -X Technical Data

30 ir Cylinder: With End Lock M Series ø3, ø40, ø50, ø63, ø80, ø00 RoHS How to Order With auto switch With auto switch (uilt-in magnet) Mounting type asic/without bracket L xial foot F Rod flange G Head flange C Single clevis D Double clevis T Center trunnion M L 3 MD L mm mm mm mm mm mm Port thread type uilt-in Magnet Cylinder Model Nil Rc If a built-in magnet cylinder without an TN NPT auto switch is required, there is no need TF G to enter the symbol for the auto switch. (Example) MD40-00 Cylinder stroke Refer to Standard Strokes on page H H N N Manual release N Non-locking L Locking Locking position H Locking at head end R Locking at rod end W Locking at both ends Suffix (Rod boot) Nil None J Nylon tarpaulin K Heat resistant tarpaulin M9W Made to Order For details, refer to page 47. Number of auto switches Nil pcs. S pc. 3 3 pcs. n n pcs. uto switch Nil Without auto switch * For applicable auto switches, refer to the table below. pplicable uto Switches/Refer to pages 575 to 70 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Electrical entry Indicator light Wiring (Output) Load voltage uto switch model Lead wire length [m] DC C Tie-rod mounting and mounting 0.5 (Nil) (M) 3 (L) 5 (Z) Pre-wired connector pplicable load 3-wire (NPN) M9N V V V v v Grommet 3-wire (PNP) 4 V 5 V, V M9P V V V v v IC circuit -wire V M9 V V V v v Terminal 3-wire (NPN) 5 V, V G39 conduit -wire V K39 3-wire (NPN) M9NW V V V v v Diagnostic indication 5 V, V IC circuit 3-wire (PNP) M9PW V V V v v Relay, (-color indicator) Yes -wire V M9W V V V v v PLC 3-wire (NPN) 4 V M9N Water resistant 5 V, V v v V v v Grommet 3-wire (PNP) M9P (-color indicator) v v V v v IC circuit -wire V M9 * v v V v v Diagnostic output (-color indicator) 4-wire (NPN) 5 V, V F59F V V v v IC circuit Magnetic field resistant -wire P3DW V V V v (-color indicator) (Non-polar) P4DW V V v 3-wire Yes (Equiv. to NPN) 5 V 96 V V IC circuit Grommet 00 V 93 V V V V No 00 V or less 90 V V IC circuit Yes 00 V, 00 V 54 V V V Terminal conduit Relay, PLC No V 00 V or less 64 V V -wire 4 V PLC Yes 00 V, 00 V DIN terminal 44 Relay, Diagnostic indication (-color indicator) Grommet 59W V V PLC * Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please contact SMC regarding water resistant types with the above model numbers. * Lead wire length symbols: 0.5 m Nil (Example) M9NW 3 m L (Example) M9NWL m M (Example) M9NWM 5 m Z (Example) M9NWZ * Solid state auto switches marked with p are produced upon receipt of order. * Since there are other applicable auto switches than listed above, refer to page 43 for details. * The D-9l/M9l/P3DWl auto switches are shipped together, (but not assembled). (However, auto switch mounting brackets are assembled for the D-9l/M9l before shipment.) 46

31 ir Cylinder: With End Lock M Series Specifications Symbol ir cushion ction Fluid Proof pressure Double acting, Single rod ir.5 MPa Max. operating pressure.0 MPa Min. operating pressure 0.5 MPa * mbient and fluid temperature Lubrication Without auto switch: 0 to 70 C (No freezing) With auto switch: 0 to 60 C Non-lube Operating piston speed 50 to 000 mm/s llowable stroke tolerance Up to 50: , 5 to 000: 0, 00 to 500: 0 Cushion ir cushion Port size (Rc, NPT, G) /8 /4 3/8 / CJ CJP CJ JCM CM CM3 Mounting * 0.05 MPa except locking parts asic, xial foot, Rod flange, Head flange, Single clevis, Double clevis, Center trunnion CG CG3 Symbol -Xl Made to Order Click here for details Specifications Change of rod end shape Tie-rod, cushion valve, tie-rod nut, etc. -XC7 made of stainless steel -XC0 Dual stroke cylinder/double rod type -XC4 Change of trunnion bracket mounting position Double clevis and double knuckle joint -XC7 pins made of stainless steel -XC9 Double knuckle joint with spring pin -XC30 Rod trunnion * ll Made-to-Order products have the same cover shapes as the current products. Refer to pages 45 to 43 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting uto switch mounting brackets/part no. Operating range Locking Specifications Locking position Head end, Rod end, oth ends Holding force (Max.) N ø3 ø40 ø50 ø63 ø80 ø ack lash.5 mm or less Manual release Non-locking type, Locking type Standard Strokes Standard stroke 3 5, 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700, , 50, 75, 00, 5, 50, 75, 00, 50, 300, 350, 400, 450, 500, 600, 700, 800 Intermediate strokes are available. (No spacer is used.) ccessories JM M M C CS CS Mounting asic xial foot Rod flange Head flange Single clevis Double clevis Center trunnion Rod end nut V V V V V V V Standard Clevis pin V Locking release bolt (N type only) V V V V V V V Option Single knuckle joint V V V V V V V Double knuckle joint (with pin) V V V V V V V Rod boot V V V V V V V * Refer to page 40 for dimensions and part numbers. (Except locking release bolt and rod boot) 47 D- -X Technical Data