Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43

Size: px
Start display at page:

Download "Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43"

Transcription

1 CAT.EUS- B -UK Free Mount Cylinder A space-saving air cylinder with multiple surfaces capable of direct mounting. Offered in many variations. Space-saving The multiple surface direct mounted rectangular body with no brackets allows freedom of the mounting surface. This enables space-saving designs for equipment. Auto Switch Capable Mounting Axial mounting (Body tapped) Vertical mounting (Body through-holes) Lateral mounting (Body through-holes) Series CU Series Variations Standard Series CU Non-rotating Series CUK Long stroke Series CU Series Action Double acting Single acting Double acting Single acting Double acting Rod Page Single rod Double rod 2 Single rod (Retracted/Extended) Single rod Double rod Single rod (Retracted/Extended) Single rod,,,,, Long stroke, Non-rotating rod Series CUK Double acting Single rod 3 With air cushion Series CU-A Double acting Single rod,, For vacuum Series ZCUK Double acting Single rod,,,, Made to Order -XB : Heat resistant (10 C) -XB : Cold resistant (-0 C) -XB : Low speed ( to 0 mm/s) -XB : Low speed ( to 0 mm/s) -XC1 : Intermediate stroke (with a spacer built-in) -XC : Seals made of fluorine rubber -XC3 : Non-rotating plate (No protrusion from the rod end) P. 3 Related Products Copper/Fluorine-free: Series - Clean Series: Series /- Copper/Fluorine/Silicon-based free + Low particle generation: Series 21/- Low speed: Series CUX P., 23, 3 P.

2 Series CU Precautions on Free Mount 1. Operating speed Make sure to connect a speed controller to the cylinder and adjust its speed to 00 mm/s or less. If a load is to be attached to the end of the rod, adjust the speed to the maximum speed shown in Graph (1) or less, in accordance with the added mass. Graph (1) Load Weight and Maximum Speed 0 0 ø ø ø How to read the graph Using the CU to drive a load weighing 2. kg: From the vertical axis in the graph on the left, extend the horizontally from 2. kg., and drop down from the point at which it intersects with the tube bore ø. The maximum speed will be 11 mm/s. Load weight (kg) (2.) 1 0. ø ø ø [Double acting (D), Single acting, Spring return (S)] ø [Single acting, Spring extend (T)] Rod end allowable lateral load Make sure that the lateral load that is applied to the rod end will be no more than the values shown in the tables. The tables show the value for a single rod. For double rods, please contact SMC. Standard Double Acting, Single Rod Without auto switch: CU - D Stroke Stroke Stroke Model Model Model CU CU CU CU CU CU Non-rotating Rod Type Without auto switch: CUK - D (N) (N) (N) CU CU CU CU CU CU CU CU CU CU CU CU With auto switch: CDU - D With auto switch: CDU - S With auto switch: CDU - T Stroke Stroke Stroke Model Model Model CDU CDU CDU CDU CDU CDU Stroke Stroke Stroke Model Model Model CUK CUK CUK CUK CUK CUK CUK CUK CUK CUK CUK CUK CUK CUK CUK CUK CUK CUK (N) (N) (N) CDU CDU CDU CDU CDU CDU CDU CDU CDU CDU CDU CDU Stroke Stroke Stroke Model Model Model CDUK CDUK CDUK CDUK CDUK CDUK 0 0 (11) Maximum speed (mm/s) Single Acting, Spring Return (S) Without auto switch: CU - S CDUK CDUK CDUK CDUK CDUK CDUK Single Acting, Spring Extend (T) Without auto switch: CU - T CDUK CDUK CDUK CDUK CDUK CDUK Non-rotating Rod Type Non-rotating Rod Type Single Acting, Spring Return (S) Single Acting, Spring Extend (T) (N) Without auto switch: CUK - S(N) Without auto switch: CUK - T (N) With auto switch: CDUK - D (N) With auto switch: CDUK - S (N) With auto switch: CDUK - T (N)

3 Free Mount Cylinder Double Acting, Single Rod Series CU ø, ø, ø, ø, ø, ø How to Order CU Without auto switch 30 D With auto switch CDU 30 D MB Built-in magnet mm mm mm mm mm mm Action D Double acting Number of auto switches - S 2 pcs. 1 pc. - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled. Symbol - TN TF Type M Rc1/ NPT1/ G1/ Port thread type ø, ø, ø, ø, ø ø ø ø Standard stroke ø, ø, ø ø, ø, ø,, 1,,, 30,, 1,,, 30, 0, 0 Applicable Auto Switches/Refer to page P. to 2 for further information on auto switches. Type Special function Electrical entry Indicator light Yes Wiring (Output) 3-wire Grommet (NPN equivalent) No 2-wire 2V 3-wire (NPN) 3-wire (PNP) 2-wire Grommet 2V 3-wire (NPN) Diagnostic indication 3-wire (PNP) (2-colour indication) 2-wire Lead wire length symbols: 0. m Nil (Example) MN 3 m L (Example) MNL m Z (Example) MNZ Reed switch Solid state switch Yes Load voltage DC AC model Perpendicular Normally closed (NC=b contact), solid states switches (Model D-FG, FH) are also available. For detail, refer Best Peneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue. In-line Lead wire length (m) Pre-wired 0. 3 connector (Nil) (L) (Z) Applicable load IC V AV A circuit V 0 V A3V A3 Relay, PLC V, V 0 V or less A0V A0 IC circuit MNV MN V, V IC MPV MP circuit V MBV MB Relay, MNWV MNW PLC V, V IC MPWV MPW circuit V MBWV MBW Solid state switches marked with are produced upon receipt of order. 2

4 Series CU Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Lubrication Piston speed Cushion Rod end thread Thread tolerance Stroke length tolerance Air 1.0 MPa 0. MPa 0. MPa 0.0 MPa 0.0 MPa Without auto switch: to 0 C (No freezing) With auto switch: to 0 C (No freezing) Non-lube 0 to 00 mm/s Rubber bumper Male thread JIS Class mm JIS Symbol Double acting, Single rod Standard Stroke Minimum Stroke for Auto Switch Mounting No. of auto switches mounted,,,, For "Long Stroke", refer to P. 3. Standard stroke,, 1,,, 30,, 1,,, 30, 0, 0 Applicable auto switch D-A, D-A V D-M, D-M V D-M W, D-M WV 1 pc. 2 pcs. Theoretical Output (N) Made to Order Specifications (For details, refer to P.3.) Rod size 3 Operating direction OUT IN Piston area (mm 2 ) Operating pressure (MPa) Symbol -XB Specifications Heat resistant (10 C) OUT IN XB -XB Cold resistant ( 0 C) Low speed ( to 0 mm/s) OUT IN XB -XC1 Low speed ( to 0 mm/s) Intermediate stroke (with a spacer built-in) OUT IN XC Seals made of fluorine rubber Refer to Pneumatic Clean Series catalog for clean room specifications. OUT IN OUT IN Tightening Torque When mounting Series CU, refer to the below table.,, Hexagon socket head cap screw dia. M3 M M M Proper tightening torque (N m) 1.0 ±% 2. ±%. ±%.0 ±% Weight /( ): Denotes the values with D-A3. (g) Cylinder stroke Model C(D)U- D C(D)U- D (2) 3 (1) (3) 0 (0) 2 (3) () 31 (1) () 3 () 2 (2) 3 () () C(D)U- D 0 () () 2 (2) () () 0 (1) C(D)U- D () (13) (1) () (1) 10 (1) () 1 (231) C(D)U- D 1 (230) (2) 2 (2) (2) 2 (303) 21 (3) 2 (3) (3) C(D)U- D (33) 2 (3) 3 (3) 33 () 3 (3) 32 (0) 30 (0) () For the auto switch weight, refer to P. to 2. 3

5 Free Mount Cylinder Double Acting, Single Rod Series CU Copper-free -CU Stroke D Copper-free The type which prevents copper based ions from generating by changing the copper based materials into electroless nickel plated treatment or noncopper materials in order to eliminate the effects by copper based ions or fluororesins over the colour cathode ray tube. Minimum Operating Pressure Minimum operating pressure Construction ø 0., 0.0 (MPa),, 0.0 Specifications Action Maximum operating pressure Cushion Stroke With auto switch Double acting, Single rod,,,,, 1.0 MPa Rubber bumper Same as standard type (Refer to page 2.) Mountable ø ø to ø Component Parts No Description Cylinder tube Head cover Piston Piston rod Bumper A Bumper B Snap ring Material Aluminum alloy Brass Aluminum alloy Brass Aluminum alloy Stainless steel Urethane Urethane Carbon tool steel Replacement Parts: Seal Kit Kit no. CUD-PS CUD-PS CUD-PS CUD-PS CUD-PS Note Hard anodized ø to ø, Electroless nickel plated ø to ø, Clear chromated ø to ø ø to ø, Chromated Phosphate coated Contents Set of nos. above!,!,! Seal kit includes!,!,!. Order the seal kit, based on each bore size. Component Parts No. 1 1 Description Rod end nut Bushing Magnet holder Magnet Piston gasket Piston seal Rod seal Gasket Material Carbon steel Oil-impregnated sintered alloy Brass Magnetic material NBR Note Nickel plated ø

6 Series CU Dimensions: Double Acting, Single Rod ø, ø 2-ø P through -ø T counterbore S + Stroke Z + Stroke Rod end nut 2-ø P through 2-M ø to ø Rod End Nut/Accessory Width across flats L Rod end nut A' 2-ø P through 2-ø P through -ø T counterbore S + Stroke Z + Stroke 2-M (ø: 1/) Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore Material: Carbon steel d H1 B1 C1 M3 M M M M M x A A' B C D E GA GB H J K L MM NN P Q QA R T depth. depth. depth..3 depth.3 depth depth Without auto switch S Z Note) With auto switch S Z M3 M M M M M x 1. Note) stroke (CU-D): 1. mm M3 depth M3 depth M depth M depth M depth M depth

7 Free Mount Cylinder Double Acting, Single Rod Series CU Proper Auto Switch Mounting Position (Detection at stroke end) and Its Mounting Height D-A D-M D-M W (2.) ( ): Denotes the values of D-A3. D-A V D-M V D-M WV () ( ): Denotes the values of D-M V, D-M WV. CDU Double Acting, Single Rod D-A, D-A V D-M, D-M W D-M V, D-M WV A B W 2.() 1.(1) 2(0.) ( 1.).( 3).( ) A B 3... W A B 3... W Note 1) Figures in the table above are used as a reference when mounting the auto switches for stroke end detection. In the case of actually setting the auto switches, adjust them after confirming their operation. Note 2) Negative figures in the table W indicate an auto switch is mounted inward from the edge of the cylinder body. Note 3) In the case of the stroke or the stroke, there are times in which the switch will not turn OFF or 2 switches will turn ON simultaneously due to their movement range. Therefore, set the position approximately 1 to mm outward from the values given in the table above. Then, perform an operation inspection to make sure that the switches operate normally (if 1 switch is used, make sure that it turns ON and OFF properly; if 2 switches are used, make sure that both switches turn ON). Note ) ( ) in column W is the dimensions of D-A3. Operating Range model D-A /A V D-M /M V D-M W/M WV Since this is a guideline including hysteresis, not meant to be guaranteed. (assuming approximately ±30% dispersion.) There may be the case it will vary substantially depending on an ambient environment

8 Series CU Mounting of Auto Switch Auto Switch Groove D-A /M /A V/M V/M W/M WV Watchmakers' screwdriver -ø.2 Set screw When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of to mm. Use a tightening torque of approximately 0. to 0. N m. A B When free mounting cylinders equipped with auto switches are used, the auto switches could activate unintentionally if the installed distance is less than the dimensions shown in the table. Therefore, make sure to provide a greater clearance. Due to unavoidable circumstances, if they must be used with less distance than the dimensions given in the table, the cylinders must be shielded. Therefore, affix a steel plate or a magnetic shield plate (MU-S0) to the area on the cylinder that corresponds to the adjacent auto switch. (Please contact SMC for details.) Auto switches may malfunction if a shield plate is not used. Caution on Proximity Installation Mounting pitch l

9 Free Mount Cylinder Double Acting, Double Rod Series CUW ø, ø, ø, ø, ø, ø How to Order Without auto switch CUW 30 D With auto switch CDUW 30 D MB Built-in magnet Double rod mm mm mm mm mm mm Action D Double acting Number of auto switches - S 2 pcs. 1 pc. - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled. Symbol - TN TF Type M Rc1/ NPT1/ G1/ Port thread type ø, ø, ø, ø, ø ø ø ø Standard stroke ø, ø, ø ø, ø, ø,, 1,,, 30, 0, 0, 0,, 1,,, 30, 0, 0, 0, 0, 0, 0, 0 Applicable Auto Switches/Refer to page to 2 for further information on auto switches. Reed switch Solid state switch Indicator light Yes Yes Lead wire length (m) Pre-wired 0. 3 connector (Nil) (L) (Z) Type Special function Load voltage Electrical Wiring model entry (Output) DC AC Perpendicular In-line Applicable load Grommet 3-wire IC V AV A (NPN equivalent) circuit V 0 V A3V A3 2-wire 2 V Relay, PLC No V, V 0 V or less A0V A0 IC circuit 3-wire (NPN) MNV MN IC V, V 3-wire (PNP) MPV MP circuit 2-wire V Grommet 2 V MBV MB Relay, 3-wire (NPN) MNWV MNW IC PLC Diagnostic indication V, V 3-wire (PNP) MPWV MPW circuit (2-colour indication) 2-wire V MBWV MBW Lead wire length symbols: 0. m Nil (Example) MN Solid state switches marked with are produced upon receipt of order. 3 m L (Example) MNL m Z (Example) MNZ Normally closed (NC=b contact), solid states switches (Model D-FG, FH) are also available. For detail, refer to Best Peneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue.

10 Series CUW Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Lubrication Piston speed Cushion Rod end thread Thread tolerance Stroke length tolerance Air 1.0 MPa 0. MPa 0.1 MPa 0. MPa 0.0 MPa Without auto switch: to 0 C (No freezing) With auto switch: to 0 C (No freezing) Non-lube 0 to 00 mm/s Rubber bumper Male thread JIS Class mm Standard Stroke,,,, Standard stroke,, 1,,, 30, 0, 0, 0,, 1,,, 30, 0, 0, 0, 0, 0, 0, 0 JIS Symbol Double acting, Double rod Minimum Stroke for Auto Switch Mounting No. of auto switches mounted Applicable auto switch D-A, D-A V D-M, D-M V D-M W, D-M WV 1 pc. 2 pcs. Theoretical Output (N) Rod size Piston area (mm 2 ) Operating pressure (MPa) Weight /( ): Denotes the values with D-A3. (g) Model Stroke C(D)UW- D 2 () 30 (0) 3 () 3 () 0 (0) () 1 (1) () () C(D)UW- D () () 3 (3) () 2 (2) () () () () C(D)UW- D () 1 (1) () (1) 2 (1) () 3 () () () C(D)UW- D 1 () 1 () 1 (1) () 1 (1) 1 (23) 3 (20) 0 (2) 2 (3) 301 (33) (3) 33 (30) 3 () C(D)UW- D 20 (2) 20 (31) 20 (33) 300 (3) 1 (30) 31 (00) 31 (0) 21 (0) 1 () 01 (0) 1 (00) 1 (0) 21 (0) C(D)UW- D 3 (3) 3 (2) (00) 1 (2) () 0 () () (00) () 3 (1) 3 (1) 0 (2) 0 () For the auto switch weight, refer to page to 2. Tightening Torque When mounting Series CUW, refer to page 3.

11 Free Mount Cylinder Double Acting, Double Rod Series CUW Construction ø With auto switch ø ø to Component Parts No Description Cylinder tube Rod cover Rod cover retainer Piston Piston Piston rod Piston rod Bushing Material Aluminum alloy Aluminum bearing alloy Aluminum alloy Brass Brass Aluminum alloy Stainless steel Stainless steel Oil-impregnated sintered alloy Replacement Parts: Seal Kit Kit no. Note Hard anodized Chromated Hard anodized ø ø, ø ø to ø, Chromated CUWD-PS ø CUWD-PS Seal kit includes!,!,!. Order the seal kit, based on each bore size. Component Parts No Description Material Bumper Urethane Rod end nut Carbon steel Hexagon socket head cap screw Carbon steel Magnet Magnetic material Piston gasket Piston seal NBR Rod seal Gasket / Part no. CUWD-PS CUWD-PS Note Nickel plated Nickel plated CUWD-PS

12 Series CU Dimensions: Double Acting, Double Rod ø, ø -øt counterbore S + Stroke W + Stroke Z + 2 x Stroke Rod end nut 2-M x 0. ø to ø Rod End Nut/Accessory Width across flats L A' -øt counterbore S + Stroke Z + 2 x Stroke A' W + Stroke Width across flats L Rod end nut 2-M x 0. (ø: Rc 1/) Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore size Material: Carbon steel d M3 M M M M M x 1. H1 B1 C A R 2 A'. 1 1 SA. B T C depth. depth. depth..3 depth.3 depth depth. D 3 W E GA 1.. Note) GB H Without auto switch With auto switch S Z 0. 3 S Z J K L MM NN 1 M3 1 M M 30 M 3 M M x 1. Note) stroke (CUW-D): GA = M3 depth M3 depth M depth M depth M depth M x 1.0 depth P Q. QA 2...

13 Free Mount Cylinder Double Acting, Double Rod Series CUW Proper Auto Switch Mounting Position (Detection at stroke end) and Its Mounting Height D-A D-M D-M W (2.) ( ): Denotes the values of D-A3. D-A V D-M V D-M WV () ( ): Denotes the values of D-M V, D-M WV. D-A, D-A V D-M, D-M W D-M V, D-M WV A B W 3.( 1).( ).( ) (.) 1.( ).( 1) A Note 1) Figures in the table above are used as a reference when mounting the auto switches for stroke end detection. In the case of actually setting the auto switches, adjust them after confirming their operation. Note 2) Negative figures in the table W indicate an auto switch is mounted inward from the edge of the cylinder body. Note 3) In the case of the stroke or the stroke, there are times in which the switch will not turn OFF or 2 switches will turn ON simultaneously due to their movement range. Therefore, set the position approximately 1 to mm outward from the values given in the table above. Then, perform an operation inspection to make sure that the switches operate normally (if 1 switch is used, make sure that it turns ON and OFF properly; if 2 switches are used, make sure that both switches turn ON). Note ) ( ) in column W is the dimensions of D-A3. B W A B W

14 Free Mount Cylinder Single Acting, Single Rod, Spring Return/Extend Series CU ø, ø, ø, ø, ø, ø How to Order Without auto switch CU 1 S With auto switch CDU 1 S MB Symbol - TN TF Built-in magnet Type M Rc1/ NPT1/ G1/ mm mm mm mm mm mm Port thread type ø, ø, ø, ø, ø ø ø ø Action S T Standard stroke ø, ø, ø ø, ø, ø - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled. Single acting, Spring return Single acting, Spring extend,, 1 Number of auto switches - S 2 pcs. 1 pc. Applicable Auto Switches/Refer to page to 2 for further information on auto switches. Reed switch Solid state switch Indicator light Yes Yes Lead wire length (m) Pre-wired 0. 3 connector (Nil) (L) (Z) Type Special function Load voltage Electrical Wiring model entry (Output) DC AC Perpendicular In-line Applicable load Grommet 3-wire IC V AV A (NPN equivalent) circuit V 0 V A3V A3 2-wire 2 V Relay, PLC No V, V 0 V or less A0V A0 IC circuit 3-wire (NPN) MNV MN IC V, V 3-wire (PNP) MPV MP circuit 2-wire V Grommet 2 V MBV MB Relay, 3-wire (NPN) MNWV MNW IC PLC Diagnostic indication V, V 3-wire (PNP) MPWV MPW circuit (2-colour indication) 2-wire V MBWV MBW Lead wire length symbols: 0. m Nil (Example) MN Solid state switches marked with are produced upon receipt of order. 3 m L (Example) MNL m Z (Example) MNZ Normally closed (NC=b contact), solid states switches (Model D-FG, FH) are also available. For detail, refer to Best Peneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue.

15 Free Mount Cylinder Single Acting, Single Rod, Spring Return/Extend Series CU JIS Symbol Single acting, Spring return Single acting, Spring extend Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Lubrication Piston speed Cushion Rod end thread Thread tolerance Stroke length tolerance Note) ø with auto switch type: One side rubber bumper Standard Stroke,,,,, Air 1.0 MPa 0. MPa 0.2 MPa 0.1 MPa 0. MPa Without auto switch: to 0 C (No freezing) With auto switch: to 0 C (No freezing) Non-lube 0 to 00 mm/s Rubber bumper Male thread JIS Class mm Note) Standard stroke,, 1 Minimum Stroke for Auto Switch Mounting No. of auto switches mounted 1 pc. 2 pcs. Applicable auto switch D-A, D-A V D-M, D-M V D-M W, D-M WV Made to Order Specifications (For details, refer to page 3.) Symbol Specifications -XC Seals made of fluorine rubber Theoretical Output Action Operating pressure (MPa) ø ø.... Spring return (S) ø..3 ø 3 ø ø ø ø Spring extend (T) ø ø 1 ø ø 1 3 For the reactive force of spring return, refer to Best Pneumatics catalogue (N) Weight/( ): Denotes the values with D-A3. Model Stroke C(D)U- S,T (2) (3) C(D)U- S,T 3(1) 0(0) C(D)U- S,T 0() () C(D)U- S,T () (13) C(D)U- S,T 1(230) (2) C(D)U- S,T (33) 2(3) For the weight of auto switch, refer to page to (3) () 1(1) 3(10) 23(2) 3() (g) Tightening Torque When mounting a CU single acting series, refer to page 3. 1

16 Series CU Construction Single acting, Spring return With auto switch ø ø to ø Component Parts No Description Cylinder tube Head cover Piston Piston Piston rod Bumper A Bumper B Return spring Material Aluminum alloy Brass Aluminum alloy Brass Aluminum alloy Brass Stainless steel Urethane Urethane Piano wire Replacement Parts: Seal Kit Kit no. Note Hard anodized ø to ø, Electroless nickel plated ø to ø, Clear chromated ø to ø ø to ø, Chromated ø Zinc chromated CUS-PS Seal kit includes!,!. Order the seal kit, based on each bore size. CUS-PS Component Parts No Description Spring seat Spring seat Snap ring Rod end nut Bushing Magnet holder Magnet Piston gasket Piston seal Gasket / Part no. CUS-PS Material Brass Brass Carbon tool steel Carbon steel Oil-impregnated sintered alloy Brass Magnetic material NBR CUS-PS Note Phosphate coated Nickel plated ø CUS-PS 1

17 Free Mount Cylinder Single Acting, Single Rod, Spring Return/Extend Series CU Construction Single acting, Spring extend With auto switch ø ø ø to ø Component Parts No. Description Material Note No. 1 Cylinder tube Aluminum alloy Hard anodized 2 3 Head cover Piston Brass Brass ø to ø, Electroless nickel plated ø to ø Aluminum alloy Aluminum alloy ø to ø, Clear chromated ø to ø, Chromated Piston Piston rod Bumper A Bumper B Return spring Brass Stainless steel Urethane Urethane Piano wire ø Zinc chromated Replacement Parts: Seal Kit CUT-PS CUT-PS Kit no. Seal kit includes!,!. Order the seal kit, based on each bore size. Component Parts Description Spring seat Stopper Snap ring Rod end nut Bushing Plug with fixed orifice Magnet Piston gasket Piston seal Rod seal / Part no. CUT-PS Material Brass Brass Carbon tool steel Carbon steel Oil-impregnated sintered alloy Alloy steel Magnetic material NBR CUT-PS Note ø Phosphate coated Nickel plated Black zinc chromated CUT-PS

18 Series CU Dimensions: Single Acting, Spring Return ø, ø -øt counterbore Rod end nut Bleed port M ø to ø Rod End Nut/Accessory Width across flats L -øt counterbore Rod end nut Bleed port M (ø: Rc 1/) Material: Carbon steel Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore size d M3 M M M M M x 1. H1 B1 C A A'. 1 1 B C D 3 E GA GB... H J 1 2 K L MM M3 M M M M M x 1. NN M3 depth M3 depth M depth M depth M depth M depth P Q. QA 2... R 2 T depth. depth. depth..3 depth.3 depth depth. 1 st S st Without auto switch With auto switch Z S Z 1 st st st st st st st st st st 1 2 3

19 Free Mount Cylinder Single Acting, Single Rod, Spring Return/Extend Series CU Dimensions: Single Acting, Spring Extend ø, ø H + Stroke -øt counterbore Rod end nut M Plug with fixed orifice ø to ø Rod End Nut/Accessory Width across flats L A' H + Stroke -øt counterbore Rod end nut M (ø: Rc 1/) Plug with fixed orifice Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore size Material: Carbon steel d M3 M M M M M x 1. H1 B1 C A A'. 1 1 B C D 3 E GA GB... H J 1 2 K L MM M3 M M M M M x 1. NN M3 depth M3 depth M depth M depth M depth M depth P Q. QA 2... R 2 T depth. depth. depth..3 depth.3 depth depth. V 3. st S st Without auto switch 1 st st 2 3 Z st st 1 0 st S st With auto switch 1 st st 2 3 Z st st 1 0 1

20 Series CU Proper Auto Switch Mounting Position and Its Mounting Height: Single Acting, Spring Return D-A D-M D-M W (2.) ( ): Denotes the values of D-A3. D-A V D-M V D-M WV () () ( ): Denotes the values of D-M V, D-M WV. Single Acting, Spring Return Stroke D-A, D-A V D-M, D-M W D-M V, D-M WV A B W A B W A B W All stroke. 0 2.() , (1) , 2(0.) , 2 2 ( 1.) ,..( 3) , ( ) Note 1) Figures in the table above are used as a reference when mounting the auto switches for stroke end detection. In the case of actually setting the auto switches, adjust them after confirming their operation. Note 2) Negative figures in the table W indicate an auto switch is mounted inward from the edge of the cylinder body. Note 3) In the case of the stroke or the stroke, there are times in which the switch will not turn OFF or 2 switches will turn ON simultaneously due to their movement range. Therefore, set the position approximately 1 to mm outward from the values given in the table above. Then, perform an operation inspection to make sure that the switches operate normally (if 1 switch is used, make sure that it turns ON and OFF properly; if 2 switches are used, make sure that both switches turn ON). Note ) ( ) in column W is the dimensions of D-A3. 1

21 Free Mount Cylinder Single Acting, Single Rod, Spring Return/Extend Series CU Proper Auto Switch Mounting Position and Its Mounting Height: Single Acting, Spring Extend D-A D-M D-M W (2.) ( ): Denotes the values of D-A3. D-A V D-M V D-M WV () () ( ): Denotes the values of D-M V, D-M WV. Single Acting, Spring Extend Stroke All stroke, 1, 1, 1, 1, 1 A B W.. D-A, D-A V (3) 1.(1).( ) 2(0.) (.) ( 1.) (.).( 3).( ).( ).( ) D-M, D-M W A B W 1... Note 1) Figures in the table above are used as a reference when mounting the auto switches for stroke end detection. In the case of actually setting the auto switches, adjust them after confirming their operation. Note 2) Negative figures in the table W indicate an auto switch is mounted inward from the edge of the cylinder body. Note 3) In the case of the stroke or the stroke, there are times in which the switch will not turn OFF or 2 switches will turn ON simultaneously due to their movement range. Therefore, set the position approximately 1 to mm outward from the values given in the table above. Then, perform an operation inspection to make sure that the switches operate normally (if 1 switch is used, make sure that it turns ON and OFF properly; if 2 switches are used, make sure that both switches turn ON). Note ) ( ) in column W is the dimensions of D-A D-M V, D-M WV A B W

22 Free Mount Cylinder: Non-rotating Rod Type Double Acting, Single Rod Series CUK ø, ø, ø, ø, ø, ø How to Order Without auto switch CUK 30 D With auto switch CDUK 30 D MB Built-in magnet Non-rotating rod type mm mm mm mm mm mm Action D Double acting Number of auto switches - S 2 pcs. 1 pc. - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled. Symbol - TN TF Type M Rc1/ NPT1/ G1/ Port thread type ø, ø, ø, ø, ø ø ø ø Standard stroke ø, ø, ø ø, ø, ø,, 1,,, 30,, 1,,, 30, 0, 0 Applicable Auto Switches/Refer to page to 2 for further information on auto switches. Reed switch Solid state switch Indicator light Yes Yes Lead wire length (m) Pre-wired 0. 3 connector (Nil) (L) (Z) Type Special function Load voltage Electrical Wiring model entry (Output) DC AC Perpendicular In-line Applicable load Grommet 3-wire IC V AV A (NPN equivalent) circuit V 0 V A3V A3 2-wire 2 V Relay, PLC No V, V 0 V or less A0V A0 IC circuit 3-wire (NPN) MNV MN IC V, V 3-wire (PNP) MPV MP circuit 2-wire V Grommet 2 V MBV MB Relay, 3-wire (NPN) MNWV MNW IC PLC Diagnostic indication V, V 3-wire (PNP) MPWV MPW circuit (2-colour indication) 2-wire V MBWV MBW Lead wire length symbols: 0. m Nil (Example) MN Solid state switches marked with are produced upon receipt of order. 3 m L (Example) MNL m Z (Example) MNZ Normally closed (NC=b contact), solid states switches (Model D-FG, FH) are also available. For detail, refer to Best Peneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue. 21

23 Free Mount Cylinder: Non-rotating Rod Type Double Acting, Single Rod Series CUK JIS Symbol Double acting, Single rod Made to Order Specifications (For details, refer to page 3,.) Symbol Specifications -XB Heat resistant (10 C) -XB Cold resistant ( 0 C) -XB Low speed ( to 0 mm/s) -XB Low speed ( to 0 mm/s) -XC1 Intermediate stroke (with a spacer built-in) -XC Seals made of fluorine rubber Threaded for mounting a work on non-rotating -XC3 plate (No protrusion from the edge of rod) Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Lubrication Piston speed Cushion Rod end thread Thread tolerance Stroke length tolerance Rod non-rotating accuracy Note) No load: Rod retracted Standard Stroke,,,, Minimum Stroke for Auto Switch Mounting No. of auto switches mounted 1 pc. 2 pcs. Standard stroke,, 1,,, 30,, 1,,, 30, 0, 0 Weight /( ): Denotes the values with D-A3. C(D)UK- D C(D)UK- D Applicable auto switch Stroke (33) 3 () Note) 31 (1) () 3 () 1 (1) 3 () () 0 (0) () Air 1.0 MPa 0. MPa 0.1 MPa 0. MPa 0.0 MPa Without auto switch: to 0 C (No freezing) With auto switch: to 0 C (No freezing) Non-lube 0 to 00 mm/s Rubber bumper Male thread JIS Class mm ±0. ±0. For long stroke, refer to page 3. 3 (3) 3 (3) D-A, D-A V D-M, D-M V D-M W, D-M WV (g) C(D)UK- D 0 () () 2 (2) () () 0 (1) Caution Precautions Be sure to read before handling. Refer to back page 1 through to for Safety Instructions, Actuator Precautions and Auto Switch Precautions. Operating Precautions 1. Do not place your fingers in the clearance between the non-rotating plate and the cylinder tube. Your fingers could get caught between the non-rotating plate and the cylinder tube when the piston rod retracts. Therefore, never place your finger in this area. Because the cylinder outputs a great force, it could lead to injury if precautions are not taken to prevent your fingers from getting caught. 2. When using the non-rotating style, make sure that rotational torque is not applied to the piston rod. If rotational torque must be applied due to unavoidable circumstances, make sure to use it at the allowable rotational torque or less, which is shown in the table on the right. C(D)UK- D C(D)UK- D C(D)UK- D 3 (1) 2 (2) 331 (0) () (2) 3 (3) (1) 2 (30) 33 (1) For the auto switch weight, refer to page to 2. Allowable Rotational Torque Allowable rotational torque (N m) Tightening Torque 0.02 When mounting Series CUK, refer to page 3. Theoretical Output Specifications are the same as CU series double acting, single rod. Refer to page 3. 1 (1) 23 (2) 0 () (0) 20 (33) 3 () 0. (2) 2 (3) 1 (3) (23) 33 (30) (1) 21 (20) 30 (2) (3) 0. Auto Switch Mounting Position For the auto switch mounting position of Series CDUK, refer to page, since specifications are the same as standard type, double acting, single rod type.

24 Series CUK Copper-free -CUK Stroke D Copper-free The type which prevents copper based ions from generating by changing the copper based materials into electroless nickel plated treatment or noncopper materials in order to eliminate the effects by copper based ions or fluororesins over the colour cathode ray tube. Minimum Operating Pressure Minimum operating pressure Construction ø 0.1, 0. (MPa),, 0.0 Specifications Action Maximum operating pressure Cushion Stroke With auto switch Double acting, Single rod,,,,, 1.0 MPa Rubber bumper Same as standard type (Refer to page 2.) Mountable ø Section AA ø to ø Section AA Component Parts No. Description Material Note No. 1 Cylinder tube Aluminum alloy Hard anodized 2 Head cover Brass ø to ø, Electroless nickel plated Aluminum alloy ø to ø, Clear chromated Brass ø to ø, 1 3 Aluminum alloy ø to ø, Chromated 1 Stainless steel Urethane Urethane Carbon tool steel Phosphate coated Carbon steel Nickel plated 1 Section AA Piston Piston rod Bumper A Bumper B Snap ring Rod end nut Bushing Magnet holder Oil-impregnated sintered alloy Brass Replacement Parts: Seal Kit Kit no. Contents CUD-PS CUD-PS CUD-PS CUD-PS CUD-PS Set of Seal Order the seal kit, based on each bore size. ø Component Parts Description Magnet Non-rotating plate Guide rod Bushing Hexagon socket head cap screw Hexagon socket head set screw Piston gasket Piston seal Rod seal Gasket Material Magnetic material Aluminum alloy Stainless steel Oil-impregnated sintered alloy Carbon steel Carbon steel NBR Note Nickel plated Black zinc chromated Black zinc chromated 23

25 Free Mount Cylinder: Non-rotating Rod Type Double Acting, Single Rod Series CUK Dimensions: Non-rotating Rod Type; Double Acting, Single Rod ø, ø Rod end nut -øt counterbore S + Stroke Z + Stroke 2-M ø to ø Width across flats L A' -øt counterbore S + Stroke Z + Stroke Rod end nut 2-M (ø: Rc 1/) Rod End Nut/Accessory Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore size Material: Carbon steel d M3 M M M M M x 1. H1 B1 C A A'. 1 1 B C D 3 E F FL 1 2 FK 2 FY GA 1.. Note) GB... H J 1 2 K L MM M3 M M M M M NN M3 depth M3 depth M depth M depth M depth M depth Note) stroke (CUK-D): GA = 1. P Q. QA 2... R 2 T depth. depth. depth..3 depth.3 depth depth. Y Without auto switch With auto switch S Z 1 3 S Z 1 3 2

26 Free Mount Cylinder: Non-rotating Rod Type Double Acting, Double Rod Series CUKW ø, ø, ø, ø, ø, ø How to Order Without auto switch CUKW 30 D With auto switch CDUKW 30 D MB Number of auto switches mm mm mm mm mm mm Built-in magnet Non-rotating rod type Symbol - TN TF Type M Rc1/ NPT1/ G1/ Double rod Port thread type ø, ø, ø, ø, ø ø ø ø Action D Standard stroke ø, ø, ø ø, ø, ø Double acting - S 2 pcs. 1 pc. - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled.,, 1,,, 30, 0, 0, 0,, 1,,, 30, 0, 0, 0, 0, 0, 0, 0 Applicable Auto Switches/Refer to page to 2 for further information on auto switches. Reed switch Solid state switch Indicator light Yes Yes Lead wire length (m) Pre-wired 0. 3 connector (Nil) (L) (Z) Type Special function Load voltage Electrical Wiring model entry (Output) DC AC Perpendicular In-line Applicable load Grommet 3-wire IC V AV A (NPN equivalent) circuit V 0 V A3V A3 2-wire 2 V Relay, PLC No V, V 0 V or less A0V A0 IC circuit 3-wire (NPN) MNV MN IC V, V 3-wire (PNP) MPV MP circuit 2-wire V Grommet 2 V MBV MB Relay, 3-wire (NPN) MNWV MNW IC PLC Diagnostic indication V, V 3-wire (PNP) MPWV MPW circuit (2-colour indication) 2-wire V MBWV MBW Lead wire length symbols: 0. m Nil (Example) MN Solid state switches marked with are produced upon receipt of order. 3 m L (Example) MNL m Z (Example) MNZ Normally closed (NC=b contact), solid states switches (Model D-FG, FH) are also available. For detail, refer to Best Peneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue.

27 Free Mount Cylinder: Non-rotating Rod Type Double Acting, Double Rod Series CUKW Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Lubrication Piston speed Cushion Rod end thread Thread tolerance Stroke length tolerance Rod non-rotating accuracy Note) Note) No load: Rod retracted on the non-rotating plate side. Air 1.0 MPa 0. MPa 0.1 MPa 0. MPa 0. MPa Without auto switch: to 0 C (No freezing) With auto switch: to 0 C (No freezing) Non-lube 0 to 00 mm/s Rubber bumper Male thread JIS Class mm ±0. ±0. Standard Stroke,,,, Standard stroke,, 1,,, 30, 0, 0, 0,, 1,,, 30, 0, 0, 0, 0, 0, 0, 0 JIS Symbol Non-rotating rod Minimum Stroke for Auto Switch Mounting No. of auto switches mounted Applicable auto switch D-A, D-A V D-M, D-M V D-M W, D-M WV 1 pc. 2 pcs. Weight /( ): Denotes the values with D-A3. Model 1 Stroke (g) C(D)UKW- D 33 (3) 3 () 0 (0) 3 (3) () 0 (0) () () 1 (1) C(D)UKW- D 1 () () 0 (0) () () () 3 (3) 2 (2) 1 (1) C(D)UKW- D () 1 (1) () () 1 (12) (1) 3 (3) 1 (1) 1 () C(D)UKW- D 10 (1) 3 (3) 1 (21) (231) (2) 21 () 2 (2) 2 (31) 303 (33) 331 (31) 3 (3) 3 (2) 1 () C(D)UKW- D 2 (330) 2 (3) 3 (3) 33 (3) 3 () 3 (3) 21 () 2 () 00 () 1 (00) 2 (1) 23 (2) (23) C(D)UKW- D 3 (0) (3) (3) 2 (0) (3) () () 0 () 0 () 31 (0) 2 (0) 3 (31) 1 (2) * For the auto switch weight, refer to page to 2. Theoretical Output Specifications are the same as double acting, double rod (Series CUW). Refer to page. Allowable Rotational Torque Ensure that rotational torque is not applied to the piston rod of Series CUKW. If rotational torque are applied unavoidably, refer to page. Tightening Torque When mounting Series CUKW, refer to page 3. Auto Switch Mounting Position For the auto switch mounting position of Series CUKW, refer to page, since specifications are the same as double acting, double rod type. 2

28 Series CUKW Construction ø With auto switch Section AA ø Section AA ø to ø Section AA Component Parts No. Description Material Note No Cylinder tube Rod cover Rod cover retainer Piston Hard anodized 1 1 Piston Piston rod Piston rod Bushing Bumper Rod end nut Hexagon socket head cap screw Aluminum alloy Aluminum bearing alloy Aluminum alloy Brass Brass Aluminum alloy Stainless steel Stainless steel Oil-impregnated sintered alloy Urethane Carbon steel Carbon steel Replacement Parts: Seal Kit Chromated Hard anodized ø ø, ø ø to ø, Chromated CUWD-PS ø Nickel plated Nickel plated CUWD-PS Kit no. Seal @2. Order the seal kit, based on each bore size. Component Parts Description Magnet Non-rotating plate Guide rod Bushing Hexagon socket head cap screw Hexagon socket head set screw Piston gasket Piston seal Rod seal Gasket / Part no. CUWD-PS Material Magnetic material Aluminum alloy Stainless steel Oil-impregnated sintered alloy Carbon steel Carbon steel NBR CUWD-PS Note Nickel plated Black zinc chromated Black zinc chromated CUWD-PS 2

29 Free Mount Cylinder: Non-rotating Rod Type Double Acting, Double Rod Series CUKW Dimensions: Non-rotating Rod Type; Double Acting, Double Rod ø, ø -øt counterbore S + Stroke Z + 2 x Stroke W + Stroke Rod end nut 2-M ø to ø Width across flats L -øt counterbore S + Stroke Z + 2 x Stroke A' W + Stroke Width across flats L Rod end nut 2-M (ø: Rc 1/) Rod End Nut/Accessory Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore size Material: Carbon steel d M3 M M M M M x 1. H1 B1 C A A'. 1 1 B C D 3 E F FL 1 2 FK 2 FY GA 1.. Note) GB H J 1 2 L MM M3 M M M M M x 1. P Q. QA 2... R 2 Note) stroke (CUKW-D): GA = 1. SA. T depth. depth. depth..3 depth.3 depth depth. W Y Without auto switch With auto switch S Z. 3 1 S Z

30 Free Mount Cylinder: Non-rotating Rod Type Single Acting, Single Rod, Spring Return/Extend Series CUK ø, ø, ø, ø, ø, ø How to Order Without auto switch CUK 1 S With auto switch CDUK 1 S MB Built-in magnet Non-rotating rod type Number of auto switches - S 2 pcs. 1 pc. mm mm mm mm mm mm Symbol - TN TF Type M Rc1/ NPT1/ G1/ Port thread type ø, ø, ø, ø, ø ø ø ø Action S T Standard stroke ø, ø, ø ø, ø, ø - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled. Single acting, Spring return Single acting, Spring extend,, 1 Applicable Auto Switches/Refer to page to 2 for further information on auto switches. Reed switch Solid state switch Indicator light Yes Yes Lead wire length (m) Pre-wired 0. 3 connector (Nil) (L) (Z) Type Special function Load voltage Electrical Wiring model entry (Output) DC AC Perpendicular In-line Applicable load Grommet 3-wire IC V AV A (NPN equivalent) circuit V 0 V A3V A3 2-wire 2 V Relay, PLC No V, V 0 V or less A0V A0 IC circuit 3-wire (NPN) MNV MN IC V, V 3-wire (PNP) MPV MP circuit 2-wire V Grommet 2 V MBV MB Relay, 3-wire (NPN) MNWV MNW IC PLC Diagnostic indication V, V 3-wire (PNP) MPWV MPW circuit (2-colour indication) 2-wire V MBWV MBW Lead wire length symbols: 0. m Nil (Example) MN Solid state switches marked with are produced upon receipt of order. 3 m L (Example) MNL m Z (Example) MNZ Normally closed (NC=b contact), solid states switches (Model D-FG, FH) are also available. For detail, refer to Best Peneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue. 2

31 Free Mount Cylinder: Non-rotating Rod Type Single Acting, Single Rod, Spring Return/Extend Series CUK Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Lubrication Piston speed Cushion (1) Rod end thread Thread tolerance Stroke length tolerance Rod non-rotating accuracy (2) Note 1) ø: With auto switch, single rubber bumper Note 2) No load: Rod retracted Air 1.0 MPa 0. MPa 0.23 MPa 0.1 MPa 0. MPa Non-lube 0 to 00 mm/s Rubber bumper on both ends Male thread JIS Class 2 ±0. ±0. Without auto switch: to 0 C (No freezing) With auto switch: to 0 C (No freezing) mm Standard Stroke,,,,, Standard stroke,, 1 JIS Symbol Single acting, Spring return Single acting, Spring extend Minimum Stroke for Auto Switch Mounting No. of auto switches mounted Applicable auto switch D-A, D-A V D-M, D-M V D-M W, D-M WV 1 pc. 2 pcs. Symbol Specifications -XC Seals made of fluorine rubber -XC3 Made to Order Specifications (For details, refer to page 3,.) Threaded for mounting a work on non-rotating plate (No protrusion from the edge of rod) Weight /( ): Denotes the values with D-A3 Model Stroke 1 C(D)UK- S T (33) (1) () C(D)UK- S T 3 () () () C(D)UK- S T 0 1 () (0) (1) C(D)UK- S T 3 (1) () () C(D)UK- S T 2 21 (2) (2) (330) C(D)UK- S T (0) (3) (00) For the auto switch weight, refer to page to 2. Tightening Torque When mounting a CUK single acting series, refer to page 3. Theoretical Output Specifications are the same as single acting, spring return/spring extend type (Series CU). Refer to page 1. Spring Reaction Force For the reactive force of spring return, refer to Best Pneumatics catalogue. Auto Switch Mounting Position For the auto switch mounting position of CDUK series single acting, spring return/spring extend, refer to page 1 to, since specification are the same as standard type, single acting, spring return/spring extend type. Allowable Rotational Torque Make sure that rotational torque is not applied to the piston rod of the CUK series single acting type cylinder. If the rotation torque were applied unavoidably, refer to page. (g) 30

32 Series CUK Construction Single acting, Spring return With auto switch ø Section AA ø Section AA ø to ø Section AA Component Parts No. Description Material Note No. 1 Cylinder tube Aluminum alloy Hard anodized 2 3 Head cover Piston Brass Brass ø to ø, Electroless nickel plated ø to ø 1 Aluminum alloy Aluminum alloy ø to ø, Clear chromated ø to ø, Chromated 1 Piston Piston rod Bumper A Bumper B Return spring Spring seat Spring seat Brass Stainless steel Urethane Urethane Piano wire Brass Brass ø Zinc chromated Replacement Parts: Seal Kit CUS-PS CUS-PS Kit no. Seal Order the seal kit, based on each bore size. Component Parts Description Snap ring Rod end nut Bushing Magnet holder Magnet Non-rotating plate Guide rod Bushing Hexagon socket head cap screw Hexagon socket head set screw Piston gasket Piston seal Gasket / Part no. CUS-PS Material Carbon tool steel Carbon steel Oil-impregnated sintered alloy Brass Magnetic material Aluminum alloy Stainless steel Oil-impregnated sintered alloy Carbon steel Carbon steel NBR CUS-PS Note Phosphate coated Nickel plated ø Nickel plated Black zinc chromated Black zinc chromated CUS-PS 31

33 Free Mount Cylinder: Non-rotating Rod Type Single Acting, Single Rod, Spring Return/Extend Series CUK Construction Single acting, Spring extend ø With auto switch Section AA ø Section AA ø to ø Section AA Component Parts No Description Cylinder tube Head cover Piston Piston Piston rod Bumper A Bumper B Return spring Spring seat stopper Snap ring Material Aluminum alloy Brass Aluminum alloy Brass Aluminum alloy Brass Stainless steel Urethane Urethane Piano wire Brass Brass Carbon tool steel Replacement Parts: Seal Kit Note Hard anodized ø to ø, Electroless nickel plated ø to ø, Clear chromated ø to ø ø to ø, Chromated ø Zinc chromated ø Phosphate coated CUT-PS CUT-PS Kit no. Seal Order the seal kit, based on each bore size. Component Parts No Description Rod end nut Bushing Plug with fixed orifice Magnet Non-rotating plate Guide rod Bushing Hexagon socket head cap screw Hexagon socket head set screw Piston gasket Piston seal Rod seal / Part no. CUT-PS Material Carbon steel Oil-impregnated sintered alloy Alloy steel Magnetic material Aluminum alloy Stainless steel Oil-impregnated sintered alloy Carbon steel Carbon steel NBR CUT-PS Note Nickel plated Black zinc chromated Nickel plated Black zinc chromated Black zinc chromated CUT-PS

34 Series CUK Dimensions: Non-rotating Rod Type; Single Acting, Spring Return ø, ø -øt counterbore Rod end nut Bleed port M ø to ø Width across flats L -øt counterbore Rod end nut Bleed port M (ø: Rc 1/) A' Rod End Nut/Accessory Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore size Material: Carbon steel d M3 M M M M M x 1. H1 B1 C A A'. 1 1 B C D 3 E F FL 1 2 FK 2 FY GA GB... H J 1 2 K L MM M3 M M M M M x 1. NN M3 depth M3 depth M depth M depth M depth M depth P Q. QA 2... R 2 T depth. depth. depth..3 depth.3 depth depth. Y st Without auto switch With auto switch S Z S Z st st st st st 3 st st st st st st 3 33

35 Free Mount Cylinder: Non-rotating Rod Type Single Acting, Single Rod, Spring Return/Extend Series CUK Dimensions: Non-rotating Rod Type; Single Acting, Spring Extend ø, ø H + Stroke -øt counterbore Rod end nut M Plug with fixed orifice ø to ø Width across flats L A' H + Stroke -øt counterbore Rod end nut M (ø: Rc 1/) Plug with fixed orifice Rod End Nut/Accessory Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore size Material: Carbon steel d M3 M M M M M x 1. H1 B1 C A A'. 1 1 B C D 3 E F FL 1 2 FK 2 FY GA GB... H J 1 2 K L MM M3 M M M M M x 1. NN M3 depth M3 depth M depth M depth M depth M depth P Q. QA 2... R 2 T depth. depth. depth..3 depth.3 depth depth. Y st Without auto switch With auto switch S Z S Z st st st 1 3 st st st st st st 1 3 st 1 3 1st

36 Free Mount Cylinder: Long Stroke Type Double Acting, Single Rod Series CU ø, ø, ø, ø, ø, ø How to Order Without auto switch CU 30 0 D With auto switch CDU 30 0 D MB Built-in magnet mm mm mm mm mm mm Action D Double acting Number of auto switches - S 2 pcs. 1 pc. - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled. Symbol - TN TF Type M Rc1/ NPT1/ G1/ Port thread type ø, ø, ø, ø, ø ø ø ø Long stroke ø, ø, ø ø, ø, ø 0, 0, 0 0, 0, 0, 0, 0 Applicable Auto Switches/Refer to page to 2 for further information on auto switches. Reed switch Solid state switch Indicator light Yes Yes Lead wire length (m) Pre-wired 0. 3 connector (Nil) (L) (Z) Type Special function Load voltage Electrical Wiring model entry (Output) DC AC Perpendicular In-line Applicable load Grommet 3-wire IC V AV A (NPN equivalent) circuit V 0 V A3V A3 2-wire 2 V Relay, PLC No V, V 0 V or less A0V A0 IC circuit 3-wire (NPN) MNV MN IC V, V 3-wire (PNP) MPV MP circuit 2-wire V Grommet 2 V MBV MB Relay, 3-wire (NPN) MNWV MNW IC PLC Diagnostic indication V, V 3-wire (PNP) MPWV MPW circuit (2-colour indication) 2-wire V MBWV MBW Lead wire length symbols: 0. m Nil (Example) MN Solid state switches marked with are produced upon receipt of order. 3 m L (Example) MNL m Z (Example) MNZ Normally closed (NC=b contact), solid states switches (Model D-FG, FH) are also available. For detail, refer to Best Peneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue. 3

37 Free Mount Cylinder: Long Stroke Type Double Acting, Single Rod Series CU Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Lubrication Piston speed Cushion Rod end thread Thread tolerance Stroke length tolerance Air 1.0 MPa 0. MPa 0. MPa 0.0 MPa 0.0 MPa Without auto switch: to 0 C (No freezing) With auto switch: to 0 C (No freezing) Non-lube 0 to 00 mm/s Rubber bumper Male thread JIS Class mm Standard Stroke,,,, Standard stroke 0, 0, 0 0, 0, 0, 0, 0 JIS Symbol Double acting, Spring rod Weight /( ): Denotes the values with D-A3. Stroke Model (g) C(D)U- D 3 (3) () 0 () C(D)U- D () 2 (2) 0 (0) C(D)U- D 2 (2) () 1 (1) Symbol -XB Made to Order Specifications (For details, refer to P.3.) Specifications Heat resistant (10 C) C(D)U- D C(D)U- D C(D)U- D 2 (3) 33 () 2 (0) 23 (2) 3 () (2) 20 (2) 31 (0) (00) (31) (2) 0 () 30 (31) () 1 () -XB -XB Cold resistant ( 0 C) Low speed ( to 0 mm/s) For the auto switch weight, refer to page to 2. -XB Low speed ( to 0 mm/s) -XC1 -XC Intermediate stroke (with a spacer built-in) Seals made of fluorine rubber Auto Switch Mounting Position For the auto switch mounting position of CDU long stroke series, refer to page, since specifications are the same as standard type, double acting, single rod type. Tightening Torque Refer to page 3 for mounting a long stroke type. Theoretical Output Specifications are the same as CU series double acting, single rod. Refer to page 3. 3

38 Series CU Copper-free -CU Stroke D Copper-free The type which prevents copper based ions from generating by changing the copper based materials into electroless nickel plated treatment or noncopper materials in order to eliminate the effects by copper based ions or fluororesins over the colour cathode ray tube. Minimum Operating Pressure Minimum operating pressure Construction ø 0., 0. (MPa),, 0.0 Specifications Action Maximum operating pressure Cushion Stroke With auto switch Double acting, Single rod,,,,, 1.0 MPa Rubber bumper Same as standard type (Refer to page 3.) Mountable ø ø to ø Component Parts No Description Cylinder tube Rod cover Head cover Piston Piston rod Bumper A Bumper B Material Aluminum alloy Aluminum bearing alloy Brass Aluminum alloy Brass Aluminum alloy Stainless steel Urethane Urethane Note Hard anodized Hard anodized ø to ø, Electroless nickel plated ø to ø, Clear chromated ø to ø ø to ø, Chromated Component Parts No. 1 1 Description Snap ring Rod end nut Magnet holder Magnet Piston gasket Piston seal Rod seal Gasket Material Carbon tool steel Carbon steel Brass Magnetic material NBR Note Phosphate coated Nickel plated ø Replacement Parts: Seal Kit Kit no. CUD-PS CUD-PS CUD-PS CUD-PS CUD-PS Contents Set of nos. above!,!,!. Seal kit includes!,!,!. Order the seal kit, based on each bore size. 3

39 Free Mount Cylinder: Long Stroke Type Double Acting, Single Rod Series CU Dimensions: Double Acting, Single Rod ø, ø -øt counterbore S + Stroke Z + Stroke Rod end nut 2-M ø to ø Rod End Nut/Accessory Width across flats L A' Rod end nut -øt counterbore S + Stroke Z + Stroke 2-M (ø: Rc 1/) Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore Material: Carbon steel d H1 B1 C1 M3 M M M M M x A A' B C D E GA GB H J K L MM NN P Q QA M3 M M M M M x 1. M3 depth M3 depth M depth M depth M depth M depth R 2 T depth. depth. depth..3 depth.3 depth depth. Without auto switch S Z With auto switch S Z

40 Free Mount Cylinder: Long Stroke Type Non-rotating Rod, Double Acting, Single Rod Series CUK ø, ø, ø, ø, ø, ø How to Order Without auto switch CUK 0 30 D With auto switch CDUK 30 0 D MB Built-in magnet Non-rotating rod type Number of auto switches - S 2 pcs. 1 pc. mm mm mm mm mm mm Action D Double acting Cylinder stroke - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled. Symbol - TN TF Type M Rc1/ NPT1/ G1/ Port thread type ø, ø, ø, ø, ø ø ø ø ø, ø, ø ø, ø, ø 0, 0, 0 0, 0, 0, 0, 0 Applicable Auto Switches/Refer to page to 2 for further information on auto switches. Reed switch Solid state switch Indicator light Yes Yes Lead wire length (m) Pre-wired 0. 3 connector (Nil) (L) (Z) Type Special function Load voltage Electrical Wiring model entry (Output) DC AC Perpendicular In-line Applicable load Grommet 3-wire IC V AV A (NPN equivalent) circuit V 0 V A3V A3 2-wire 2 V Relay, PLC No V, V 0 V or less A0V A0 IC circuit 3-wire (NPN) MNV MN IC V, V 3-wire (PNP) MPV MP circuit 2-wire V Grommet 2 V MBV MB Relay, 3-wire (NPN) MNWV MNW IC PLC Diagnostic indication V, V 3-wire (PNP) MPWV MPW circuit (2-colour indication) 2-wire V MBWV MBW Lead wire length symbols: 0. m Nil (Example) MN Solid state switches marked with are produced upon receipt of order. 3 m L (Example) MNL m Z (Example) MNZ Normally closed (NC=b contact), solid states switches (Model D-FG, FH) are also available. For detail, refer to Best Peneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue. 3

41 Free Mount Cylinder: Long Stroke Type Non-rotating Rod, Double Acting, Single Rod Series CUK JIS Symbol Double acting, Single rod Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Lubrication Piston speed Cushion Rod end thread Thread tolerance Stroke length tolerance Rod non-rotating accuracy Note) Note) No load: Rod retracted Standard Stroke,,,, Air 1.0 MPa 0. MPa 0.1 MPa 0. MPa 0.0 MPa ±0. ±0. Standard stroke 0, 0, 0 0, 0, 0, 0, 0 Without auto switch: to 0 C (No freezing) With auto switch: to 0 C (No freezing) Non-lube 0 to 00 mm/s Rubber bumper Male thread JIS Class mm Made to Order Specifications (For details, refer to page 3.) Symbol Specifications -XB Low speed ( to 0 mm/s) -XB Low speed ( to 0 mm/s) -XC1 Intermediate stroke (with a spacer built-in) Weight /( ): Denotes the values with D-A3. Model C(D)UK- D C(D)UK- D C(D)UK- D Stroke () 1 (1) 2 (1) () () (1) 1 (1) () (1) (g) C(D)UK- D 23 (2) 2 (30) 21 (3) 31 (3) 33 (30) C(D)UK- D 0 (0) 0 () (30) () (00) C(D)UK- D 1 () () 21 () 3 (1) (03) For the auto switch weight, refer to page to 2. Allowable Rotational Torque Make sure that rotational torque is not applied to the piston rod of a long stroke type cylinder. If the rotation torque were applied unavoidably, refer to page for details. Tightening Torque When mounting a CUK long stroke series, refer to page 3. Theoretical Output Specifications are the same as CU series double acting, single rod. Refer to page 3. Auto Switch Mounting Position For the auto switch mounting position of CDUK long stroke series, refer to page, since specifications are the same as standard type, double acting, single rod type. 0

42 Series CUK Construction ø With auto switch ø Section AA Section AA ø to ø Section AA Component Parts No Description Cylinder tube Rod cover Head cover Piston Piston rod Bumper A Bumper B Snap ring Rod end nut Magnet holder Material Aluminum alloy Aluminum bearing alloy Brass Aluminum alloy Brass Aluminum alloy Stainless steel Urethane Urethane Carbon tool steel Carbon steel Brass Replacement Parts: Seal Kit Kit no. CUD-PS CUD-PS CUD-PS CUD-PS CUD-PS Note Hard anodized Hard anodized ø to ø, Electroless nickel plated ø to ø, Clear chromated ø to ø ø to ø, Chromated Phosphate coated Nickel plated ø Contents Set of Seal Order the seal kit, based on each bore size. Component Parts No Description Magnet Non-rotating plate Guide rod Bushing Hexagon socket head cap screw Hexagon socket head set screw Piston gasket Piston seal Rod seal Gasket Material Magnetic material Aluminum alloy Stainless steel Oil-impregnated sintered alloy Carbon steel Carbon steel NBR Note Nickel plated Black zinc chromated Black zinc chromated 1

43 Free Mount Cylinder: Long Stroke Type Non-rotating Rod, Double Acting, Single Rod Series CUK Dimensions: Non-rotating Rod Type; Double Acting, Single Rod ø, ø Rod end nut -øt counterbore S + Stroke Z + Stroke 2-M ø to ø Width across flats L A' -øt counterbore S + Stroke Z + Stroke Rod end nut 2-M (ø: Rc 1/) Rod End Nut/Accessory Part no. NTP-00 NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable bore size Material: Carbon steel d M3 M M M M M x 1. H1 B1 C A A'. 1 1 B C D 3 E F FL 1 2 FK 2 FY GA GB... H J 1 2 K L MM M3 M M M M M x 1. NN M3 depth M3 depth M depth M depth M depth M depth P Q. QA 2... R 2 T depth. depth. depth..3 depth.3 depth depth. Y Without auto switch With auto switch S Z 1 3 S Z 1 3 2

44 Series CU Made to Order Specification -XB Heat resistant (10 C) -XB Low speed ( to 0 mm/s) Enter the applicable model number. XB Enter the applicable model number. XB Applicable Model CU Standard, Double acting, Single rod CUK Non-rotating rod, Double acting, Single rod CU Long stroke, Double acting, Single rod CUK Non-rotating rod/long stroke, Double acting, Single rod Applicable Model C(D)U Standard, Double acting, Single rod C(D)UK Non-rotating rod, Double acting, Single rod C(D)U Long stroke, Double acting, Single rod C(D)UK Non-rotating rod/long stroke, Double acting, Single rod Specifications Ambient temperature range to 10 C Not mountable Seal material Fluorine rubber Grease in use Heat resistant grease Specifications other than described above and dimensions are identical to those of standard products. -XB -XB Low speed ( to 0 mm/s) Enter the applicable model number. Applicable Model C(D)U C(D)UK C(D)U C(D)UK Cold resistant ( 0 C) Enter the applicable model number. Applicable Model CU CUK CU CUK Specifications Ambient temperature range Seal material Grease in use XB Standard, Double acting, Single rod Non-rotating rod, Double acting, Single rod Long stroke, Double acting, Single rod Non-rotating rod/long stroke, Double acting, Single rod 0 to 0 C Not mountable Low nitrile rubber Cold resistant grease Specifications other than described above and dimensions are identical to those of standard products. XB Standard, Double acting, Single rod Non-rotating rod, Double acting, Single rod Long stroke, Double acting, Single rod Non-rotating rod/long stroke, Double acting, Single rod -XC1 -XC Intermediate stroke (with a spacer built-in) Intermediate strokes are available by installing a spacer with mm in width in the standard stroke cylinder. Enter the applicable model number. Seals made of fluorine rubber Seal materials are changed to the fluorine rubber. Enter the applicable model number. XC1 Applicable Model C(D)U Standard, Double acting, Single rod C(D)UK Non-rotating rod, Double acting, Single rod C(D)U Long stroke, Double acting, Single rod C(D)UK Non-rotating rod/long stroke, Double acting, Single rod Applicable Stroke Stroke,, 3,,,, 3,,,,,, The external dimensions are the same as that of standard products with mm added to strokes above. Consult with SMC when stroke other than applicable stroke is required. XC Applicable Model C(D)U Standard, Double acting, Single rod Standard Single acting, Single rod (Retracted/Extended) Non-rotating rod, Double acting, Single rod C(D)UK Non-rotating rod, Single acting, Single rod (Retracted/Extended) C(D)U Long stroke, Double acting, Single rod C(D)UK Non-rotating rod/long stroke, Double acting, Single rod The other specifications and dimensions are the same as those of standard products. 3

45 -XC3 Series CU Made to Order Specification Threaded for mounting a work on non-rotating plate (No protrusion from the rod end) Threaded for mounting a work on the plate. FL dimension across the non-rotating plate and the piston rod end is removed. The piston rod does not stick out of the plate. Enter the applicable model number. XC3 Applicable Model C(D)UK Non-rotating rod, Double acting, Single rod Non-rotating rod, Single acting, Single rod (Retracted/Extended) Non-rotating rod/long stroke, Double acting, Single rod Dimensions 2-KI NA Double acting, Single rod Single acting, Retracted Single acting, Extended Y C FY NB FK B F H Z H + stroke B C FK 2 FY KI M3 M3 M M M M NA NB Y Action F H Double acting Single acting, Retracted Single acting, Extended Z Z Z Without With Without auto switch With auto switch Without auto switch With auto switch auto auto switch switch The dimensions other than the table above are the same as those of standard type.

46 Related Products For details, refer to the respective catalogue. Clean Series Compliant with clean environment Specifications Model Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature Operating piston speed Allowable margin of stroke length Grease in use Grade of particle generation amount - - CDU -CDU (Relief type) -CDU (Vacuum type),, 1.0 MPa 0. MPa 0. MPa 0.0 MPa 0.0 MPa Without auto switch: - to 0 C With auto switch: - to 0 C (with no freezing) 0 to 00mm/s Fluoro grease -: Grade 2 -: Grade 1 Copper/Fluorine/Silicon-based free + Low Particle Generation Compliant with the environment where no copper, fluorine and silicon are allowed and with clean environment CDU Specifications Model Proof pressure Max. operating pressure Min. operating pressure Ambient and fluid temperature Operating piston speed Allowable margin of stroke length Grease in use Grade of particle generation amount 21-CDU (Relief type) -CDU (Vacuum type),, 1.0 MPa 0. MPa 0. MPa 0.0 MPa 0.0 MPa Without auto switch: - to 0 C With auto switch: - to 0 C (with no freezing) 0 to 00 mm/s Lithium soap-based grease 21-: Grade3 -: Grade1 Low Speed Stable low speed actuation even at 0. mm/s (ø or less: 1 mm/s) C(D)UX Specifications Proof pressure Max. operating pressure Cushion Rod end thread Thread tolerance Allowable margin of stroke length Mounting 1.0MPa 0.MPa Ambient and fluid temperature Without auto switch: - to 0 C With auto switch: - to 0 C (with no freezing) Lubrication Not required (Non-lube) Operating piston speed ø, ø: 1 to 300mm/s ø to ø: 0. to 300mm/s Rubber bumber on both ends Male thread JIS Class 2 Note) Basic style Note) Tolerance Minimum Operating Pressure Minimum operating pressure (MPa) Unit: MPa 0.0

47 Free Mount Cylinder with Air Cushion Series CU New air cushion mechanism Free mount cylinder Series CU now employs an air cushion mechanism. Extended dimensions (compared to the standard CU models) are hardly noticeable. (with rubber bumper) Overall length: +1. to mm Overall height: +0 to 2 mm No air cushion protrusion! Overall width: not affected CU with air cushion CU with rubber bumper Bore size ø ø ø Extended dimensions Length Height Working principle R Piston seal H A + A' A Unique air cushion construction requires no cushion ring. Elimination of the cushion ring used in conventional type air cushions has made it possible to reduce the overall length of the cylinder while retaining all the advantages of a compact profile. A' R A' H A' When the piston is retracting, air is exhausted through both A and A' until piston seal H passes air passage A. After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. When air is supplied for the piston extension, the check valve opens and the piston extends with no delay.

48 Reduced stroke end impact and noise: New standards to meet consumer demand. Free mounting 3 types of mounting orientations can be accommodated depending on the installation conditions. Axial mounting (Tapped hole) Vertical mounting (Body through-hole) Lateral mounting (Body through-hole) Approximately 2. times of allowable kinetic energy (Compared to the old Series CU with rubber bumper) Improved allowable kinetic energy absorption. Allowable kinetic energy (J) Series CU comparison : with air cushion : with rubber bumper Improved repeatability When compared to rubber bumper type actuators, air cushion type cylinders are less likely to be affected by pressure fluctuations, and therefore better able to achieve a stable and smooth stroke. Improved sound insulation (Reduced impact noise at the stroke end) Noise reduction of more than db is possible (compared to Series CU with rubber bumper). Interchangeable mounting Mounting dimensions (J, K, R, and E) are the same as the rubber bumper type Series CU. J R E E K Size Variations Model C(D)U C(D)U C(D)U Standard stroke ø to ø Direct mounting style auto switch

49 Free Mount Cylinder with Air Cushion Series CU ø, ø, ø How to Order Without auto switch With auto switch CU CDU 0 0 A A MB Built-in magnet mm mm mm Number of auto switches - S 2 pcs. 1 pc. - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled. Symbol - TN TF Thread type Type M thread ø, ø Rc NPT ø G Air cushion A With air cushion Cylinder stroke Refer to next page for Standard Stroke. Applicable Auto Switches/Refer to page to 2 for further infomation on auto switches. Type Load voltage Lead wire length (m) Special Electrical Wiring model 0. 3 Pre-wired function entry (output) DC AC connector Perpendicular In-line (Nil) (L) (Z) Applicable load Grommet 3-wire V AV A (NPN equivalent) IC circuit V 0 V A3V A3 2-wire 2 V Relay No V, V 0 V or less A0V A0 IC circuit PLC 3-wire(NPN) MNV MN V, V 3-wire(PNP) MPV MP IC circuit 2-wire V 2 V MBV MB Grommet Relay Diagnostic indication 3-wire(NPN) MNWV MNW PLC V, V IC circuit 3-wire(PNP) MPWV MPW (2-colour indication) 2-wire V MBWV MBW Lead wire length symbols: 0. m Nil (Example) MN Note) Solid state switches marked " " are produced upon receipt of order. 3 m L (Example) MNL m Z (Example) MNZ Reed switch Solid state switch Indicator light Yes Yes Normally closed (NC=b contact), solid state switches (Model D-FG, FH) are also available. For detail, refer to Best Pneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue.

50 Series CU Specifications Type Fluid Proof pressure Maximum operating pressure Minimum operating pressure Ambient and fluid temperature Rod end thread Rod end thread tolerance Stroke length tolerance Piston speed Pneumatic (Non-lube) Air 1.0 MPa 0. MPa 0.0 MPa Without auto switch: C to 0 C (No freezing) With auto switch: C to 0 C (No freezing) Male thread JIS Class to 00 mm/s Effective Cushion Length Effective cushion length... Standard Stroke,, Standard stroke, 30, 0, 0, 0, 0, 0, 0, 0 Intermediate strokes are also available upon receipt of order. Please contact SMC. Minimum stroke length is mm. Tightening Torque:, Hexagon socket head cap screw size M M When mounting Series CU refer to the table below. Proper tightening torque (N m). ±%.0 ±% Allowable Kinetic Energy Refer to Selection on P. regarding allowable kinetic energy. Theoretical Output Operating direction OUT IN OUT IN OUT IN OUT Operating pressure (MPa) IN (N) Weight Basic Weight Standard stroke (g) Additional Weight Magnet (g)

51 Free Mount Cylinder with Air Cushion Series CU Construction u t! w q r!3!0!2 i o! e y!1 Component Parts No. Description Material No. of pcs. Note Cylinder tube Rod cover/bearing Head cover Piston Piston rod Snap ring Rod end nut Cushion needle assembly Steel ball Magnet Piston gasket Piston seal Rod seal Gasket Aluminum alloy Aluminum bearing alloy Aluminum alloy Aluminum alloy Stainless steel Carbon tool steel Carbon steel Carbon steel Magnetic material NBR NBR NBR NBR 1 Hard anodized 1 Hard anodized 1 Clear chromated 1 Chromated 1 1 Phosphate coated 1 Nickel plated (2) 2 1 (2) D- A F type Replacement Parts: Seal Kit ø ø ø Kit no. CUA-PS CUA-PS CUA-PS Contents, 1, and 1 0

52 Series CU Dimensions -NN MM ød R Q JA CA J K C CB Width across flats L A A' H E -øt counterbore S + Stroke KA B Z + Stroke 2-cushion needle 2-port E GA GB Port size A A' B C CA CB D E GA GB H J JA M M 1/ K KA L MM NN P Q R T S Z Standard stroke 30 3 M M M x 1. M with depth M with depth M with depth with depth.3 with depth with depth , 30, 0, 0, 0, 0, 0, 0, 0 1

53 Free Mount Cylinder with Air Cushion Series CU Proper Auto Switch Mounting Position (Detection at stroke end) and Its Mounting Height D-A D-M D-M W A (2.) 2. W B 0. ( ): Denotes the values of D-A3. D-A V D-M V D-M WV A () W B () ( ): Denotes the values of D-M V, D-M WV (.) (.). () Note 1) Figures in the table above are used as a reference when mounting the auto switches for stroke end detection. In the case of actually setting the auto switches, adjust them after confirming their operation. Note 2) Values in ( ) are dimensions for D-A3 type. Operating Range Switch model D-A, D-A V D-M, D-M V D-M W, D-M WV D-A, D-A V D-M, D-M W D-M V, D-M WV A B W A B W A B W.. 1 Values in this table include hysteresis and are to be used as a guide only. They do not guarantee an actual fixed range (expect approximately ±30% dispersion). Values may vary greatly depending on the operating environment. 2

54 Series CU Auto Switch Rail Position -ø.2 B -3 A A B 23 2 Caution on Proximity Installation When free mounting cylinders equipped with auto switches are used, the auto switches could activate unintentionally if the installed distance is less than the dimensions shown in the table. Therefore, make sure to provide a greater clearance. Due to unavoidable circumstances, if they must be used with less distance than the dimensions given in the table, the cylinders must be shielded. Therefore, affix a steel plate or a magnetic shield plate (MU-S0) to the area on the cylinder that corresponds to the adjacent auto switch. (Please contact SMC for details.) es may malfunction if a shield plate is not used. l Mounting pitch l 0 3

55 Series CU Specific Product Precautions 1 Be sure to read before handling. Refer to back page 1 through to for Safety Instructions, Actuator Precautions, and Auto Switch Precautions. Installation and Removal of Snap Rings Caution 1. Use appropriate pliers (Type C snap ring installing tool) for installation and removal of snap rings. 2. Even when using appropriate pliers (Type C snap ring installing tool), proceed with caution as there is a danger of the snap ring flying off the end of the pliers (tool) and causing bodily injury or damage to nearby equipment. After installation, make sure that the snap ring is securely seated into the snap ring groove before supplying air. 1. Refer to the below table for mounting cylinders. Tightening Torque s, Caution 1. Operate the cylinder to the stroke end. When the stroke is restricted by an external stopper or a clamped workpiece, sufficient cushioning and noise reduction may not be achieved. 2. Strictly observe the limiting ranges for load weight and maximum speed (Graph (1)). Also, the limiting ranges provided here are based on the condition that the cylinder is operated to the stroke end with a proper cushion needle adjustment. If operated beyond the limiting ranges, excessive impact will occur and this may cause damage to equipment. Graph (1) Load weight (kg) Caution Mounting Hexagon socket head cap screw M M Selection Proper tightening torque (N m). ±%.0 ±% : Operating pressure 0. MPa : Operating pressure 0. MPa ø ø ø Caution 3. Adjust the cushion needle to reduce excessive kinetic energy from the piston impact at the stroke end by allowing it to absorb sufficient kinetic energy during the cushion stroke. If due to improper adjustment, the piston impacts the stroke end with excessive kinetic energy (values above those given in Table (1)), an excessive impact will occur and this may cause damage to equipment.. Strictly observe the limiting ranges for the piston rod lateral load (Graph (2)). If operated beyond the limiting ranges, equipment life may be reduced or damage to equipment may occur Selection Table (1) Allowable Kinetic Energy at Piston Impact Piston speed 0 to 00 mm/s Allowable kinetic energy Piston Rod Lateral Load (Graph (2)) Lateral load (N) ø ø ø Stroke Caution Cushion Needle Adjustment 1. Keep the adjustment range for the cushion needle between the fully closed position and the rotations shown below. ø to ø Use a 3 mm flat head watchmakers screwdriver to adjust the cushion needle. The adjustment range for the cushion needle must be between the fully closed position and the open position ranges indicated in the above table. A retaining mechanism prevents the cushion needle from slipping out; however, it may spring out during operation if it is rotated beyond the ranges shown above. 0.1 Rotations 2. rotations or less (J) Maximum speed (mm/s)

56 Free Mount Cylinder for Vacuum Series ZCUK A free mount cylinder with a vacuum passage in the rod to meet the requirements for Air cylinder + Vacuum pad. A vacuum passage has been provided in the rod of the CUK cylinder to enable a vacuum pad to be installed on the end of the rod. Not necessary to provide vacuum tubing space at the end of the rod. The area around the vacuum pad is uncluttered. Non-rotationg rod A guide is provided as standard equipment Non-rotating rod accuracy (no load: when the rod is retracted on the detent plate side): ø, ø ±0. ø, ø, ø ±0. Do not apply a lateral load to the piston rod. Because the piston rod is a hollow rod, a lateral load can cause the piston rod to bend or break. Vacuum pad (Pad diameter: ø2 to ø0) <Perpendicular female thread> <Direct mounting> <Male thread> Reed switch: D-A (Heavy-duty cord, in-line entry) D-A V (Heavy-duty cord, perpendicular entry) Solid state switch: D-M, D-M W (Heavy-duty cord, in-line entry) D-M V, D-M WV (Heavy-duty cord, perpendicular entry) How to provide piping to the vacuum side Cap piping The piston rod of the vacuum side does not protrude. Also, the vacuum outlet tube does not move when the piston is operating. Vacuum port pressure range: 1 kpa to 0. MPa Pressurise only when releasing the vacuum. At that time, use it under the cylinder operating pressure. Rod piping Lighter weight than the cap piping. Can also be used for air blowing. Vacuum port pressure range: 1 kpa to 0. MPa <Barb fitting>

57 Without auto switch ZCUK C With auto switch Built-in magnet Style (Tubing method in vacuum side)/ (Rod end shape) C Cap piping/male thread mm D Cap piping/pad direct mm mounting mm Q Rod piping/male thread mm R Rod piping/ mm Pad direct mounting How to Order D ZCDUK C D MB Port thread type Symbol Type - M ø, ø, ø, ø Rc1/ ø TN TF NPT1/ G1/ ø ø Note) In the case of rod piping (Q, R), TF (G1/) is not available. Applicable Auto Switch/Refer to page to 2 for further information on auto switches. Applicable Auto Switch/ Reed switch Solid state switch How to Order Vacuum Pad Note) Refer to page for combination of cylinder and pad. <In the case of rod end male> ZPT Dia. 02 ø2 Pad type 0 ø U Flat 0 ø C Flat with ribs 0 ø D Deep ø B Bellows ø Application: ø Refer to Table (1). ø ø Material ø N 0 ø0 S 0 ø0 U F GN GS 02 U N B Female thread Table (1) Pad Dia./Pad Type Free Mount Cylinder for Vacuum Series ZCUK Vacuum entry (Mounting thread diameter) Symbol Thread dia. ø2 to ø ø to ø ø to ø ø0, ø0 B M x 0. B M x 0. B B B M x 1 M x 1. M x 1. Dia. Type Flat Flat with ribs Deep Bellows Indicator light Yes Yes S Number of auto switches - 2 pcs. S 1 pc. - Without auto switch Refer to the table below for applicable auto switches. es are shipped together but not assembled. Acting D Double acting Stroke,,, 1,,, 30,,,, 1,,, 30, 0, 0 Type Special function Refer to Best Pneumatics Load voltage Vol. / for further infomation on auto Lead switches. wire length (m) Electrical Wiring model Pre-wired entry (Output) 0. 3 DC AC connector Perpendicular In-line (Nil) (L) (Z) Applicable load Grommet 3-wire IC V AV A (NPN equivalent) circuit V 0 V A3V A3 2-wire 2 V Relay, PLC No V, V 0 V or less A0V A0 IC circuit 3-wire (NPN) MNV MN IC V, V 3-wire (PNP) MPV MP circuit 2-wire V Grommet 2 V MBV MB Relay, 3-wire (NPN) MNWV MNW IC PLC Diagnostic indication V, V 3-wire (PNP) MPWV MPW circuit (2-colour indication) 2-wire V MBWV MBW Lead wire length symbols: 0. m Nil (Example) MN Solid state switches marked with are produced upon receipt of order. 3 m L (Example) MNL m Z (Example) MNZ Normally closed (NC=b contact), solid states switches (Model D-FG, FH) are also available. For detail, refer to Best Peneumatics catalogue. For detail about auto switches with pre-wired connector, refer to Best Pneumatics catalogue. NBR Silicon rubber Urethane rubber Fluoro rubber Conductive NBR (ø2 to ø only) Conductive silicon rubber (ø2 to ø only) <In the case of pad direct mounting> ZP Dia. 02 ø2 0 ø 0 ø 0 ø ø ø ø ø ø ø 0 ø0 0 ø0 Pad type U Flat C Flat with ribs D Deep B Bellows (Except -X ) 0 U N X Pressure gauge position Applicable cylinder Symbol model D X ZC(D)UK R D - ZC(D)UK R/ Note) -X Pad: ø2 to ø diameter and flat style only available. Material N S U F GN GS NBR Silicon rubber Urethane rubber Fluoro rubber Conductive NBR (ø2 to ø only) Conductive silicon rubber (ø2 to ø only)

58 Series ZCUK Tubing system in vacuum side Model Rod end shape Applicable pad style ZCUKC Refer to next page for details. Cap piping Vacuum Male thread Cap piping Vacuum ZCUKD Pad direct mounting Series ZPT (Perpendicular vacuum entry female thread) Vacuum Rod piping Vacuum ZCUKQ Male thread Series ZPT (With pad single unit lock ring) Rod piping Vacuum ZCUKR Pad direct mounting Vacuum Caution 1. Do not place your finger in the clearance between the detent plate and the cylinder tube. Never put your finger between the nonrotating plate and cylinder tube. Your finger may be pinched when the piston rod retracts. If your finger is caught, it could injure your finger because the cylinder outputs a considerable amount of force. 2. Make sure that rotational torque is not applied to the piston rod. If this is unavoidable, operate the cylinder within the allowable rotational torque listed in the table below. Allowable Rotational Torque ø ø ø ø ø Allowable rotational torque (N m) 3. To secure a workpiece to the end of the piston rod, tighten the workpiece onto the piston rod with the piston rod fully retracted so that torque is not applied to the piston rod.. To install a cylinder, tighten it within the torque values indicated in the table below. Proper Tightening Torque ø ø ø, ø ø Precautions Be sure to read before handling. Refer to back page 1 through to for Safety Instructions, Actuator Precautions and Auto Switch Precautions. Also see pages for Vacuum Equipment Precautions in Best Pneumatics catalogue. Hexagon socket head bolt diameter M3 M M M Proper tightening torque (N m) 1.0 ±% 2. ±%. ±%.0 ±% Specifications Fluid Proof pressure Maximum operating pressure Vacuum port pressure Ambient and fluid temperature Lubrication Piston speed Cushion Stroke allowance Thread tolerance Rod tip screw Mounting Applicable pad Air 1.0 MPa 0. MPa 1 kpa to 0. MPa (At vacuum release 0 to 0. MPa) Note) Without auto-switch: to +0 C (No freezing) With auto-switch: to +0 C (No freezing) Not required 0 to 00mm/s Rubber bumper on both sides JIS Class 2 With or without (Pad direct mounting) Basic style Refer to next page for details. Note) For a cap style, supply pressure only when vacuum is released. That pressure should be less than the cylinder pressure. Non-rotating Rod Accuracy (No load/at retraction of the rod at the locking plateside) Non-rotating rod accuracy Minimum Operating Pressure ø ø ø ø ±0. ±0. (MPa) ø ø ø ø ø Min. Operating Pressure (MPa) ø

59 Free Mount Cylinder for Vacuum Series ZCUK Standard Stroke Applicable cylinder Stroke Double acting style/single rod type/non-rotating rod Stroke Mounting Vertical mounting (Body through-hole) Theoretical Output/Double Acting Type Operating pressure (MPa) Rod dia. Piston area (mm 2 ) (N) Lateral mounting (Body throughhole) Minimum Stroke for Mounting Auto Switch Number of auto switches D-A, D-A V Applicable auto switch D-M, D-M V D-M W, D-M WV 1 pc. 2 pcs. Cylinder/Applicable Pad In the case of rod end male thread Use series ZPT pad (perpendicular vacuum entry/female thread mounting). Cylinder Model 2 ZCUKC ZCUKQ ZCDUKC ZCDUKQ 0 0 Pad (ZPT02 to 0 -B to ) Rod dia. Thread dia. M x 0. M x 0. M x 1.0 M x 1. M x 1. In the case of pad direct mounting Use series ZP pad (single unit). Cylinder Model Pad (ZP02 to 0 ) Rod dia Note) ZCUKD ZCUKR ZCDUKD ZCDUKR U Note) When using ZC(D)UK R, use ZP02 to 0U -X. Pad shape is flat only. Auto Switch Groove A B

60 Series ZCDUK Proper Auto Switch Mounting Position (Detection at stroke end) and Its Mounting Height D-A D-M D-M W D-A V D-M V D-M WV ( ): Denotes the values of D-A3. ( ): Denotes the values of D-M V, D-M WV. D-A, D-A V D-M, D-M W D-M V, D-M WV A B 3 W 1. (1) 2 (0.) ( 1.). ( 3). ( ) A B... W A B... W Note 1) Figures in the table above are used as a reference when mounting the auto switches for stroke end detection. In the case of actually setting the auto switches, adjust them after confirming their operation. Note 2) Negative figures in the table show dimensions mounted inside cylinder body. Note 3) In the case of mm stroke or the mm stroke, there are times in which the switch will not turn OFF or 2 switches will turn ON simultaneously due to their movement range. Therefore, set the position approximately 1 to mm outward from the values given in the table above. Then, perform an operation inspection to make sure that the switches operate normally (if 1 switch is used, make sure that it turns ON and OFF properly; if 2 switches are used, make sure that both switches turn ON). Note ) Figures in ( ) in the table W are D-A3. Operation Range model D-A /A V D-M /M V D-M W/M WV 3... Since this is the average value at a normal temperature including hysteresis (tolerance ±30%), it is not guaranteed.

61 Free Mount Cylinder for Vacuum Series ZCDUK Auto Switch Specifications Mounting of Auto Switch Mounting Watchmaker's screwdriver Set screw Cautions on Proximity lnstallation When free mounting cylinders equipped with auto switches are used, the auto switches could activate unintentionally if the installed distance is less than the dimensions shown in the table. Therefore, make sure to provide a greater clearance. Due to unavoidable circumstances, if they must be used with less distance than the dimensions given in the table, the cylinders must be shielded. Therefore, affix a steel plate or a magnetic shield plate (MU-S0) to the area on the cylinder that corresponds to the adjacent auto switch. (Please contact SMC for details.) es may malfunction if a shield plate is not used. To tighten the auto switch mounting screws, use a watchmaker s screwdriver with a grip diameter of to mm. Tighten the screws to a torque of approximately 0. to 0. N m. Mounting pitch l 30 0 Weight Basic Style/With Auto Switch Model ZC(D)UKC ZC(D)UKQ 3 () 3 () 10 (21) 30 (3) 1 () () () 1 (1) (3) 21 () ( ): Denotes the values with D-A3. Cylinder stroke () () 1 (1) () 3 (3) (1) (1) () () 3 () (2) (2) 2 () 2 (3) 300 (30) 3 (3) 3 (3) 33 (02) 32 (1) 21 (0) 0 (1) () (3) (1) (2) 3 () (2) () 1 (2) 3 () () 3 (3) () 1 (1) () () (1) 3 (3) 0 (0) () (1) 1 (1) (2) 1 () 1 (20) 21 () 23 () 21 (3) 2 (33) 2 (3) 31 (3) 33 (3) 3 (1) 3 () 3 () 1 (2) 1 () () 1 (1) 1 () 31 (0) 1 () (g) 0

62 Series ZCUK Construction Cap piping/male thread: ZC(D)UKC ø With auto switch Section AA Pad direct mounting In the case of ZC(D)UKD ø to ø With auto switch Pad direct mounting In the case of ZC(D)UKD Section AA Component Parts No Description Material Cylinder tubing Aluminum alloy Rod cover B Aluminum bearing alloy Cap Aluminum alloy Piston Aluminum alloy Piston rod Stainless steel Bush Oil impregnated sintered metal Plate Aluminum alloy Guide rod Stainless steel Bush Oil impregnated sintered metal Hexagon set screw Carbon steel Hexagon socket head cap screw Carbon steel Hexagon set screw Carbon steel Note Hard anodized Chromated Hard anodized Chromated Nickel plated Black zinc chromated Black zinc chromated Nickel plated Component Parts No Description Damper Magnet Rod end nut Piston gasket Piston seal Rod seal Gasket Gasket for cap Seal washer Material Urethane Magnetic material Carbon steel NBR NBR Rolled steel/nbr Note Nickel plated Replacement Parts: Seal Kit (Cap piping) Kit no. ø ZCU-PS ø ZCU-PS / Part no. ø ZCU-PS ø ZCU-PS ø ZCU-PS Seal kit consist contained in one kit, and can be ordered using the order number for each respective tubing bore size. 1

63 Free Mount Cylinder for Vacuum Series ZCUK Construction Rod piping-male thread: ZC(D)UKQ ø With auto switch Section AA Pad direct mounting In the case of ZC(D)UKR ø to ø With auto switch Section AA Pad direct mounting In the case of ZC(D)UKR Component Parts No. Description Material 1 Cylinder tubing Aluminum alloy 2 3 Rod cover B Rod cover retainer plate Aluminum bearing alloy Aluminum alloy Piston Aluminum alloy Piston rod Stainless steel Bush Oil impregnated sintered metal Plate Aluminum alloy Guide rod Stainless steel Bush Oil impregnated sintered metal Hexagon set screw Carbon steel Hexagon socket head cap screw Carbon steel Hexagon set screw Carbon steel Note Hard anodized Chromated Hard anodized Chromated Nickel plated Black zinc chromated Black zinc chromated Nickel plated Component Parts No. Description Material Damper Urethane 1 1 Magnet auto switch Magnetic material Rod end nut Carbon steel 1 Piston gasket NBR 1 Socket Carbon steel 1 Gasket Piston seal 21 Rod seal NBR Gasket 23 Seal washer Rolled steel/nbr Note Nickel plated ø only ø only Replacement Parts: Seal Kit (Rod piping) Kit no. ø CUW-PS ø CUW-PS / Part no. ø CUW-PS ø CUW-PS ø CUW-PS Seal kit consist @2 contained in one kit, and can be ordered using the order number for each respective tubing bore size. 2

64 Series ZCUK Vacuum Piping: Cap Piping/Rod End Shape: Male Thread ZC(D)UKC Cylinder bore Stroke D ø Vacuum port size M M ø1. through hole 2-ø3.2 through hole -ø depth counterbore 3 + Stroke + 2 x Stroke + Stroke Seal washer 2-ø3.2 through hole Port size 2-M 30 + Stroke ø to ø Vacuum port size ød Through Width across flats L -øt counterbore S + Stroke Z + 2 x Stroke SA + Stroke Port size 2-M [ø: 2-Rc 1/] Seal washer GC + Stroke Model Port size Stroke range Air port Vacuum port A A' B C ød ød E F FK FL FY GA GC ZC(D)UKC M M to Note) 31 ZC(D)UKC M 1 to ZC(D)UKC M 1 to ZC(D)UKC 1 1 to Model H J L MM ZC(D)UKC 2 1 M (0) 1. ZC(D)UKC 2 M.. 3 () 21 ZC(D)UKC 33 M.. 0 (0) 21 ZC(D)UKC 2 2 M x (2) ( ): In the case of a mounted auto switch. Note) In the case of ZCUKC-D: 1. mm. øp Q QA R S SA øt. depth..3 depth.3 depth depth. Y Z. (.) () () (1) 3

65 ZC(D)UKD Cylinder bore Stroke D Free Mount Cylinder for Vacuum Series ZCUK Vacuum Piping: Cap Piping/Rod End Shape: Pad Direct Mounting ø Vacuum port size ø1. Through 2-ø3.2 through -ø depth counterbore 3 + Stroke + 2 x (Stroke) + Stroke Pad for ZCUKD (ZP02 to 0U -X) 2-ø3.2 through Port size 2-M 30 + Stroke ø to ø Vacuum port size ød Through Width across flats L -øt counterbore SA + Stroke S + Stroke Z + 2 x Stroke Port size 2-M [ø: Rc 1/] Use series ZP pad CG + Stroke Model ZC(D)UKD ZC(D)UKD ZC(D)UKD ZC(D)UKD Port size Air port Vacuum port M M M 1 M Stroke range to 30 to 0 to 0 to 0 øa.. A'. B 2 0 C ød 2 3 ød E F FK 2 FL 1 2 FY GA Note) GC Model H J L øp Q QA R S SA øt W Y Z ZC(D)UKD (0) 1.. depth. ZC(D)UKD () 21.3 depth ZC(D)UKD (0) 21.3 depth ZC(D)UKD (2) depth. ( ): In the case of a mounted auto switch. Note) In the case of ZCUKD-D: 1. mm (.) () () (1)

66 Series ZCUK Vacuum Piping: Rod Piping/Rod End Shape: Male Thread ZC(D)UKQ Cylinder bore Stroke D ø M ø1. through 2-ø3.2 through -ø depth counterbore 3 + Stroke x Stroke + Stroke Seal washer 2-ø3.2 through Port size 2-M ø/ø2. Urethane tube (TU0) or Soft nylon tube (TS0) ø to ø ød Through through Width across flats L -øt counterbore S + Stroke Z + 2 x Stroke HA + Stroke Vacuum port size Socket (Only ø) M Hexagon width across flats Port size 2-M [ø: 2-Rc 1/] Seal washer Model ZC(D)UKQ ZC(D)UKQ ZC(D)UKQ ZC(D)UKQ Port size Air port Vacuum port M M (2) M M M M 1 1 Stroke range to 30 to 0 to 0 to 0 A A'. 1 1 B 2 0 C ød 2 3 ød E F FK 2 FL 1 2 FY GA. (1) GC Model H HA J L MM øp Q QA R ZC(D)UKQ 2 1 M (0).. depth. 1.. (.) ZC(D)UKQ 2 M.. 3 ().3 depth 1. () ZC(D)UKQ 33 M.. 0 (0).3 depth 2. () ZC(D)UKQ 2 2 M x (2) depth. 30. () ( ): In the case of a mounted auto switch. Note 1) In the case of ZCUKR-D: 1. mm. Note 2) In the case of socket equipped type. S SA øt Y Z

67 Free Mount Cylinder for Vacuum Series ZCUK Vacuum Piping: Rod Piping/Rod End Shape: Pad Direct Mounting ZC(D)UKR Cylinder bore Stroke D ø ø1. through 2-ø3.2 through -ø depth counterbore 3 + Stroke x Stroke + Stroke Pad for ZCUKR (ZP02 to 0U -X) 2-ø3.2 through Port size 2-M x 0. ø/ø2. Urethane tube (TU0) or Soft nylon tube (TS0) ø to ø ød Through through Width across flats L -øt counterbore S + Stroke Z + 2 x Stroke HA + Stroke Vacuum port size Socket (Only ø) M Hexagon width across flats Port size 2-M [ø: 2-Rc 1/] Use series ZP pad Model Port size Air port Vacuum port ZC(D)UKR ZC(D)UKR ZC(D)UKR M M M M (2) M M ZC(D)UKR 1 1 Stroke range to 30 to 0 to 0 to 0 øa.. A. B 2 0 C ød 2 3 ød E F FK 2 FL 1 2 FY GA. (1) GC Model H HA J L øp Q QA R S ZC(D)UKR (0).. depth (.) ZC(D)UKR ().3 depth 1. () ZC(D)UKR (0).3 depth 2. () ZC(D)UKR (2) depth. 30. () ( ): In the case of a mounted auto switch. Note 1) In the case of ZCUKQ-D: 1. mm. Note 2) In the case of socket equipped type. SA øt W Y Z

68 Series ZCUK Dimensions of Pad Mounted Model Rod end shape: Male thread Tubing bore: ø Tubing bore: ø to ø0 Model ZC(D)UKC ZC(D)UKQ ZC(D)UKC ZC(D)UKQ ZC(D)UKC ZC(D)UKQ ZC(D)UKC ZC(D)UKQ ZC(D)UKC ZC(D)UKQ Dia. ødq HQ HP ødq HQ HP ødq HQ HP ødq HQ HP ødq HQ HP Flat/Flat with ribs Deep Bellows Applicable pad model ZPT -B ZPT -B ZPT -B 3 1. ZPT -B 3.. ZPT -B. Rod end shape: Pad direct mounting Tubing bore: ø Tubing bore: ø to ø0 Model ZC(D)UKD ZC(D)UKR ZC(D)UKD ZC(D)UKR ZC(D)UKD ZC(D)UKR ZC(D)UKD ZC(D)UKR ZC(D)UKD ZC(D)UKR Dia. ødq HQ HP ødq HQ HP ødq HQ HP ødq HQ HP ødq HQ HP Note) ZP U -X: Flat type only. Flat/Flat with ribs Deep Bellows Applicable pad model Note) ZP U -X ZP ZP ZP ZP Accessory Dimensions (Attached only to a rod end male thread type.) Rod end nut Seal washer Core sheet Seal Part no. NTP-0 NTJ-01A NT-01A NT-02 NT-03 Applicable cylinder bore d M x 0. M x 0. M x 1.0 M x 1. M x 1. H 2. Material: Carbon steel B 1 C D..... Part no. WCS x 0. WCS x 0. WCS x 1 WCS x 1 WCS x 1 Applicable cylinder bore Material: Core sheet Rolled steel NBR Seal t D

69 Series CU Auto Switch Specifications Auto Switch Common Specifications Type Leakage current Operating time Impact resistance Insulation resistance Withstand voltage Ambient temperature Enclosure Reed switch Solid state switch None 3-wire: 0 µa or less 2-wire: 0. ma or less 1.2 ms 300 m/s 2 1 ms or less 00 m/s 2 0 MΩ or more at 00 VDC Mega (between lead wire and case) 00 VAC for 1 minute (between lead wire and case) to 0 C IEC2 standard IP, JIS C 0 watertight construction Lead Wire Length Lead wire length indication (Example) D-MP L Lead wire length Nil 0. m L 3 m Z m Note 1) Applicable auto switch with m lead wire Z Solid state switch: Manufactured upon receipt of order as standard. Note 2) To designate solid state switches with flexible specifications, add -1 after the lead wire length. Oilproof flexible heavy-duty cord is used for D-M as standard. There is no need to suffix -1 to the end of part number. (Example) D-MPWVL- 1 Contact Protection Box: CD-P, CD-P <Applicable switch model> D-A A V The auto switches above do not have a built-in contact protection circuit. Therefore, please use a contact protection box with the switch for any of the following cases: Where the operation load is an inductive load. Where the wiring length to load is greater than m. Where the load voltage is 0 VAC. The contact life may be shortened. (Due to permanent energising conditions.) Specifications Part No. Load voltage Maximum load current Lead wire length CD-P 0 VAC 0 VAC ma. ma Switch conneciton side 0. m Load connection side 0. m CD-P 2 VDC 0 ma Flexible specification Auto Switch Hysteresis The hysteresis is the difference between the position of the auto switch as it turns on and as it turns off. A part of operating range (one side) includes this hysteresis. Internal Circuit CD-P Surge absorber Choke coil OUT Brown OUT Blue Hysteresis Switch operation position (ON) Note) Reed switch: 2 mm or less Solid state switch: 1 mm or less CD-P Dimension Zener diode Choke coil OUT (+) Brown OUT ( ) Blue Switch operation position (OFF) Note) Hysteresis may fluctuate depending on the operating environment. Contact SMC if hysteresis causes an operational problem. Connection To connect a switch unit to a contact protection box, connect the lead wire from the side of the contact protection box marked SWITCH to the lead wire coming out of the switch unit. Keep the switch as close as possible to the contact protection box, with a lead wire length of no more than 1 meter.

70 Series CU Auto Switch Connections and Examples Basic Wiring Solid state 3-wire, NPN Switch main circuit Brown Load Black Solid state 3-wire, PNP Switch main circuit Brown Black Load 2-wire (Solid state switch) Switch main circuit Brown Load 2-wire (Reed switch) Indicator light Protective circuit etc. Brown Load Blue Blue Blue Blue (Power supplies for switch and load are separate.) Switch main circuit Brown Load Black Blue Switch main circuit Brown Load Blue Indicator light Protective circuit etc. Brown Load Blue Examples of Connection to PLC (Programmable Logic Controller) Sink input specifications 3-wire, NPN Black Input Brown Switch Blue COM PLC internal circuit 2-wire Brown Input Source input specifications 3-wire, PNP Black Input Brown Switch Blue COM PLC internal circuit 2-wire Blue Input Connect according to the applicable PLC input specifications, as the connection method will vary depending on the PLC input specifications. Switch Switch Blue COM PLC internal circuit Brown COM PLC internal circuit Connection Examples for AND (Serial) and OR (Parallel) 3-wire AND connection for NPN output (using relays) Switch 1 Switch 2 Brown Black Blue Relay Brown Black Relay Blue Load Relay contact AND connection for NPN output (performed with switches only) Brown Switch 1 Black Blue Load Switch 2 Brown Black Blue The indicator lights will light up when both switches are turned ON. OR connection for NPN output Switch 1 Switch 2 Brown Black Blue Brown Black Blue Load 2-wire with 2-switch AND connection Switch 1 Switch 2 Brown Blue Brown Blue Load When two switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up if both of the switches are in the ON state. Power supply Internal Load voltage at ON = x 2 pcs. voltage voltage drop = 2 V - V x 2 pcs. = V Example: Power supply is 2 VDC. Internal voltage drop in switch is V. 2-wire with 2-switch OR connection (Solid state swich) Brown When two switches Load are connected in parallel, a malfunction Switch 1 Blue may occur because the load voltage will Switch 2 Brown increase when in the OFF state. Blue Load voltage at OFF = Leakage current x 2 pcs. x Load impedance = 1 ma x 2 pcs. x 3 kω = V Example: Load impedance is 3 kω. Leakage current from switch is 1 ma. (Reed switch) Because there is no current leakage, the load voltage will not increase when turned OFF. However, depending on the number of switches in the ON state, the indicator lights may sometimes dim or not light because of the dispersion and reduction of the current flowing to the switches.

71 Reed Switch: Direct Mounting Style D-A0(V)/D-A3(V)/D-A(V) Grommet Electrical entry : In-line Caution Operating Precautions Fix the switch with the existing screw installed on the switch body. The switch may be damaged if a screw other than the one supplied, is used. Auto Switch Internal Circuit D-A0(V) Reed switch Contact protection box CD-P CD-P OUT (±) Brown OUT (±) Blue Auto Switch Specifications PLC: Abbreviation for Programmable Logic Controller D-A0/D-A0V (without indicator light) part no. Applicable load Load voltage Maximum load current Contact protection circuit 2 V AC/DC or less 0 ma D-A0/D-A0V IC circuit, Relay, PLC V AC/DC or less 0 ma None 0 V AC/DC or less ma Internal resistance 1 Ω or less (including lead wire length of 3 m) D-A3/D-A3V/D-A/D-AV (with indicator light) part no. Applicable load Load voltage 2 VDC D-A3/D-A3V Relay, PLC 0 VAC D-A/D-AV IC circuit to VDC Contact protection circuit Internal voltage drop Indicator light to 0 ma to ma None D-A3 2. V or less (to ma)/3 V or less (to 0 ma) D-A3V 2. V or less Red LED lights when ON ma 0. V or less Lead wires D-A0(V)/D-A3(V) Oilproof vinyl heavy-duty cord: ø2., 0.1 mm 2 x 2 cores (Brown, Blue), 0. m D-A(V) Oilproof vinyl heavy-duty cord: ø2., 0.1 mm 2 x 3 cores (Brown, Black, Blue), 0. m Note 1) Refer to page for reed switch common specifications. Note 2) Refer to page for lead wire lengths. Note 3) Under ma, the strength of the indicator light is poor. In some cases, visibility of the indicator light will not be possible where the output signal is less than 2. ma. However, there is no problem in terms of contact output, when an output signal exceeds 1 ma or more. Weight Note 3) Load current range and max. load current For details about certified products conforming to international standards, visit us at Unit: g D-A3(V) Reed switch LED diode Resistor Zener diode Brown Blue Contact protection box CD-P CD-P OUT (+) Brown OUT ( ) Blue model Lead wire length: 0. m Lead wire length: 3 m Dimensions D-A0/D-A3/D-A D-A0 30 D-A0V 30 M2. x l Slotted set screw D-A3 30 D-A3V 30 D-A 1 D-AV 1 Unit: mm Indicator light D-A0 type comes without indicator light D-A(V) DC (+) LED diode Brown Resistor Load Reverse OUT current Black prevention diode Reed switch DC ( ) Blue (+) DC power supply ( ) Most sensitive position Note) q In a case where the operation load is an inductive load. w In a case where the wiring load is greater than m. e In a case where the load voltage is 0 VAC. Please use the auto switch with a contact protection box any of the above mentioned cases. (For details about the contact protection box, refer to page.) D-A0V/D-A3V/D-AV M2. x l Slotted set screw Most sensitive position ( ): dimensions for D-A3. Indicator light D-A0 type comes without indicator light 0

72 Solid State Switch: Direct Mounting Style D-MN(V)/D-MP(V)/D-MB(V) Grommet 2-wire load current is reduced (2. to 0 ma) Lead-free UL certified (style 2) lead cable is used. Auto Switch Specifications D-M, D-M V (With indicator light) part no. Electrical entry direction Wiring type Output type Applicable load Power supply voltage Current consumption Load voltage Load current Internal voltage drop Leakage current Indicator light D-MN In-line D-MNV Perpendicular D-MP In-line D-MPV Perpendicular 3-wire NPN PNP IC circuit, Relay, PLC,, 2 VDC (. to 2 V) ma or less 2 VDC or less 0 ma or less 0. V or less 0 µa or less at 2 VDC For details about certified products conforming to international standards, visit us at Red LED lights when ON. Lead wires Oilproof vinyl heavy-duty cord: ø2. x 3.2 ellipse, 0.1 mm 2, D-MB(V) 0.1 mm 2 x 2 cores D-MN(V), D-MP(V) 0.1 mm 2 x 3 cores Note 1) Refer to page for solid state switch common specifications. Note 2) Refer to page for lead wire lengths. PLC: Abbreviation of Programmable Logic Controller D-MB D-MBV In-line Perpendicular 2-wire 2 VDC relay, PLC 2 VDC ( to 2 VDC) 2. to 0 ma V or less 0. ma or less Caution Operating Precautions Fix the switch with the existing screw installed on the switch body. The switch may be damaged if a screw other than the one supplied, is used. Auto Switch Internal Circuit D-MN(V) Weight model Lead wire length (m) Dimensions D-M 0. 3 D-MN(V) D-MP(V) 1 Unit: g D-MB(V) 3 3 Unit: mm DC (+) Brown Most sensitive position Switch main circuit OUT Black Mounting screw M2. x l Slotted set screw DC ( ) Blue Indicator light 2. D-MP(V) Switch main circuit DC (+) Brown OUT Black DC ( ) Blue D-M V (3000) (000) (3000) (000) D-MB(V) OUT (+) Brown. 2. Switch main circuit Mounting screw M2. x l Slotted set screw 2 Indicator light OUT ( ) Blue 2. Most sensitive position

73 2-color Indication, Solid State Switch: Direct Mounting Style D-FNW(V)/D-FPW(V)/D-FBW(V) Grommet Caution Operating Precautions Fix the switch with the existing screw installed on the switch body. The switch may be damaged if a screw other than the one supplied, is used. Auto Switch Internal Circuit D-FNW(V) Switch main circuit DC (+) Brown OUT Black Auto Switch Specifications PLC: Abbreviation for Programmable Logic Controller D-F W/D-F WV (with indicator light) part no. Electrical entry direction Wiring type Output type Applicable load Power supply voltage Current consumption Load voltage Load current Internal voltage drop Leakage current Indicator light Weight D-FNW In-line D-FNWV Perpendicular D-FPW In-line D-FPWV Perpendicular 3-wire NPN PNP IC circuit, Relay, PLC,, 2 VDC (. to 2 VDC) ma or less 2 VDC or less 0 ma or less 0 ma or less 1. V or less (0. V or less at ma 0. V or less load current) 0 µa or less at 2 VDC For details about certified products conforming to international standards, visit us at D-FBW In-line 2-wire D-FBWV Perpendicular 2 VDC relay, PLC 2 VDC ( to 2 VDC) to 0 ma V or less 0. ma or less Operating position... Red LED lights up Optimum operating position... Green LED lights up Lead wires Oilproof vinyl heavy-duty cord: ø2., 0.1 mm 2 x 3 cores (Brown, Black, Blue), 0.1 mm 2 x 2 cores (Brown, Blue), 0. m Note 1) Refer to page for solid state switch common specifications. Note 2) Refer to page for lead wire lengths. Unit: g D-FPW(V) DC ( ) Blue model Lead wire length (m) 0. 3 D-FNW(V) 3 D-FPW(V) 3 D-FBW(V) 2 Switch main circuit DC (+) Brown OUT Black DC ( ) Blue Dimensions D-F W Most sensitive position 2. Unit: mm D-FBW(V) Mounting screw M2. x l Slotted set screw OUT (+) Brown 2 Indicator light ø2. Switch main circuit 2. OUT ( ) Blue D-F WV ø Indicator light/display method Operating range ON Display Red Green Red OFF.3 2 Most sensitive position Mounting screw M2. x l Slotted set screw Indicator light Optimum operating position 2. 2

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations.

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Free Mount Cylinder Series CU A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Space-saving The multiple surface direct mounting with a square

More information

Compact Slide. Series MXH ø6, ø10, ø16, ø20

Compact Slide. Series MXH ø6, ø10, ø16, ø20 Compact Slide Series ø, ø, ø, ø The use of an endless track linear guide produces a table cylinder having excellent rigidity, linearity and non-rotating accuracy. Endless track linear guide Series Variations

More information

Free Mount Cylinder for Vacuum

Free Mount Cylinder for Vacuum Free Mount Cylinder for Vacuum Series A free mount cylinder with a vacuum passage in the rod to meet the requirements for Air cylinder + Vacuum pad. A vacuum passage has been provided in the rod of the

More information

Free Mount Cylinder. Series CU. A space saving air cylinder with multiple surfaces for mounting. The series consist of an array of cylinders.

Free Mount Cylinder. Series CU. A space saving air cylinder with multiple surfaces for mounting. The series consist of an array of cylinders. Mounting Axial mounting (Body tapped) Free Mount Cylinder eries CU Double Acting ingle Rod/Double Rod ingle Acting pring Return/Extend, Non-rotating Rod ø, ø, ø1, ø, ø, ø A space saving air cylinder with

More information

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8 Precision Cylinder Series, ø, ø6, ø, ø, ø, ø MXS Series Variations Model 8 Standard stroke (mm) 7 7 Rod end configuration Cushion Rubber bumper End lock Made to Order Rod Variable stroke/ through-hole

More information

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g.

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g. Compact Slide Series ø, ø, ø, ø RoHS Allowable moment MXS Improved by up to MXQ MXQ 2% MXF MXW MXJ MXP MXY With new high rigidity linear guide MTS Allowable moment improvement illustrated below Allowable

More information

Compact Guide Cylinder Series MGQ

Compact Guide Cylinder Series MGQ Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø0 ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

Guide Table. MGF Series

Guide Table. MGF Series Guide Table MGF Series ø, ø, ø0 Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Guide Table. ø40, ø63, ø100

Guide Table. ø40, ø63, ø100 Guide Table Series MGF ø, ø, ø Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Mini Free Mount Cylinder

Mini Free Mount Cylinder Mini Free Mount Cylinder Series ø, ø, ø, ø, ø, ø1, ø Series 1 ction Stroke 1 2 0 0 0 Clean uto switch series None Rod end Male threaded Without thread Solid state switch D-F D-M9 D-M9 W Female threaded

More information

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E -UK Dual-Rod Cylinder Series CXS New: CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ Dual-Rod Cylinder with guide functio for pick-and-place applications Series CXS! Twice the

More information

Compact Cylinder/Plate type

Compact Cylinder/Plate type Compact Cylinder/Plate type Series :,,, Width: Reduced by up to % (compared with SMC series) Total length: Reduced by up to % Volume: Reduced by up to 1% Weight: Reduced by up to % (compared with SMC series

More information

Angular Style Air Gripper

Angular Style Air Gripper Angular Style Air Gripper Series /A/M 15 Angular style air gripper Series /A/M - Auto switch is attachable. 8 mm x 0 mm x mm g Body option (Only for A-) Side piping Port Port A- Short body. 1 mm x 0 mm

More information

Guide Table. Series MGF

Guide Table. Series MGF Guide Table Series MGF ø, ø, ø0 Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E -UK Dual-Rod Cylinder Series New: Dual-Rod Cylinder with Air Cushion Compact Type Series J Dual-Rod Cylinder with guide function for pick-and-place applications Series! Twice the thrust Non-rotating

More information

22mm Space required between the bottom of the cylinder body and your equipment is reduced.

22mm Space required between the bottom of the cylinder body and your equipment is reduced. Compact Guide Cylinder ø2,,, ø2,,, ø0, ø63,, ø0 With air cushion Water resistant cylinder are now available. New Up to 7% Weight reduced! New Weight reduced by up to 7% with a shorter guide rod and thinner

More information

Compact Guide Cylinder

Compact Guide Cylinder Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

180 Angular Style Air Gripper

180 Angular Style Air Gripper 8 Angular Style Air Gripper Series 2/2 Cam Style / Rack & Pinion Style 99 8 Angular Style Air Gripper Cam Style Rack & Pinion Style Series 2/2 Series 2/Cam Style Light and compact size in small bore sizes

More information

Heavy Duty Stopper Cylinder

Heavy Duty Stopper Cylinder Heavy Duty Stopper Cylinder Series ø, ø32 To stop pallets gently Stopper cylinder with built-in shock absorber Amount of energy absorption can be adjusted to suit the load. Stops the workpiece gently with

More information

Parallel Style Air Gripper: Wide Type

Parallel Style Air Gripper: Wide Type Parallel Style Air Gripper: Wide Type Series MHL Built-in dust-protection mechanism A scraper with a dust lip is adopted for all rod rotating parts. A large amount of gripping force is provided through

More information

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting.

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting. Compact Cylinder: Type Series ø, ø, ø, ø How to Order Without auto switch D With auto switch CDQS D FW S Number of auto switches L F G D, uilt-in magnet Mounting style Through-hole/oth ends tapped common

More information

How to Order M9BW. Action. Double acting Single acting. Load voltage Electrical entry direction M9NWV M9NW 12 V 5 V, M9BWV M9BW 12 V 12 V

How to Order M9BW. Action. Double acting Single acting. Load voltage Electrical entry direction M9NWV M9NW 12 V 5 V, M9BWV M9BW 12 V 12 V Angular Type Air Gripper/Standard Type 2 Series ø, ø1, ø20, ø25 How to Order Angular type air gripper 2 20 Bore size mm 1 1 mm 20 20 mm 25 25 mm D S Action D Double acting Single acting M9BW Made to Order

More information

CAT.ES20-53 E. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E Dual-Rod Cylinder Series New: Dual-Rod Cylinder with Air Cushion Compact Type Series J Dual-Rod Cylinder with guide function for pick-and-place applications Series! Twice the thrust Non-rotating

More information

Miniature Guide Rod Cylinder ±0.1. Mounting from 2 directions

Miniature Guide Rod Cylinder ±0.1. Mounting from 2 directions Miniature Guide Rod Cylinder Series Non-rotating accuracy : Height ±0.1 Mounting from 2 directions idth Overall length Two auto switches can be mounted even for mm strokes Integral wiring/piping to one

More information

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping.

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping. Dual Rod Cylinder / Series ø,,,,, Dual rod cylinder with guide function suitable for pick & place applications. Ball bushing bearings and slide bearings are standard for all series. Dimensions for ball

More information

Series MGPS. Compact Guide Cylinder: ø50, ø80 MGP S Z73. How to Order. Applicable auto switches. Compact Guide Cylinder.

Series MGPS. Compact Guide Cylinder: ø50, ø80 MGP S Z73. How to Order. Applicable auto switches. Compact Guide Cylinder. Compact Guide Cylinder: Series S ø, Compact Guide Cylinder Compact guide cylinder Heavy duty guide rod type S Z73 mm mm How to Order Number of auto switches Nil S 2 pcs. 1 pc. Auto switch type Nil Without

More information

Compact Guide Cylinder

Compact Guide Cylinder Compact Guide Cylinder Series ø2, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Series standard type and series high precision ball bushing bearing type (except with end lock) products have been remodeled for a lightweight

More information

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder.

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder. Compact Guide Cylinder Series ø2,,, ø2,,, ø, ø63,, ø0 Up to Weight reduced by up to 24% with a shorter guide rod and thinner plate 24% Weight reduced! 3 types of bearing can be selected. Slide bearing

More information

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping.

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping. Dual Rod Cylinder J/ Series ø, ø, ø, ø, ø, Dual rod cylinder with guide function suitable for pick & place applications. Ball bushing bearings and slide bearings are standard for all series. Dimensions

More information

Compact Guide Cylinder Series MGP

Compact Guide Cylinder Series MGP Compact Guide Cylinder Series MGP ø2, ø, ø, ø, ø, ø, ø, ø,, ø0 MGJ MGP MGQ MGG MGC MGF MGZ MGT Series Variations Series Bearing type Cushion 2 0 Page Standard type MGP With air cushion MGP With end lock

More information

Rotary Actuator. New RoHS. New. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB 2. Standard type/series CRB2

Rotary Actuator. New RoHS. New. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB 2. Standard type/series CRB2 Rotary Actuator Vane Type 1, 15, 2, 3, 4 Standard Type Free Mount Type Many combinations available! Standard type/series Piping ports are located on the flat surface. Fittings can be secured firmly, piping

More information

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added.

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added. ir Cylinder ø1, ø16 Double foot Double-side bossed added to the mounting types. 4 types 7 types Improved amount of mounting freedom Head cover with boss is added. Head flange are Double foot Double-side

More information

/ ø6, ø10, ø16, ø20 A table cylinder suitable for short pitch mounting

/ ø6, ø10, ø16, ø20 A table cylinder suitable for short pitch mounting roduces a table cylinder non-rotating accuracy MXH / ø, ø, ø1, ø A table cylinder suitable for short pitch mounting Application example Auto switches offer numerous variations Reed switches, solid state

More information

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types ir Cylinder Ø 6, Ø 1, Ø New RoS Double foot ead flange Double-side bossed added to the mounting types. 4 types 7 types New or Ø 6, 3 types are 6 types Double foot Double-side bossed ead flange ead cover

More information

Slide Unit. CX2/CXWM/CXWL Series. Slide Bearing/CX2:ø10, ø15, ø25 CXWM:ø10, ø16, ø20, ø25, ø32 Ball Bushing Bearing/CXWL:ø10, ø16, ø20, ø25, ø32

Slide Unit. CX2/CXWM/CXWL Series. Slide Bearing/CX2:ø10, ø15, ø25 CXWM:ø10, ø16, ø20, ø25, ø32 Ball Bushing Bearing/CXWL:ø10, ø16, ø20, ø25, ø32 Slide Unit CX/M/L Series Slide Bearing/CX:ø0, ø, ø5 M:ø0, ø, ø0, ø5, ø3 Ball Bushing Bearing/L:ø0, ø, ø0, ø5, ø3 Provided with shock absorbers to absorb impact and noise. The slide unit can absorb energy

More information

Dual Rod Cylinder. ø6, ø10, ø15, ø20, ø25, ø32. Dual rod cylinder with guide function suitable for pick & place applications.

Dual Rod Cylinder. ø6, ø10, ø15, ø20, ø25, ø32. Dual rod cylinder with guide function suitable for pick & place applications. Dual Rod Cylinder Series J/ ø, ø0, ø, ø, ø, Dual rod cylinder with guide function suitable for pick & place applications. Twice the thrust Non-rotating accuracy ±0. Ball bushing bearings and slide bearings

More information

Low Profile Air Gripper. Series MHF2. Low profile air gripper with space-saving design is newly released. 5-77

Low Profile Air Gripper. Series MHF2. Low profile air gripper with space-saving design is newly released. 5-77 Low Profile Air Gripper Low profile air gripper with space-saving design is newly released. 5-77 Low Profile Air Gripper Height is approximately / the size of an equivalent Series MHZ2. MHZ2-D 42 Bore

More information

Series MXH/ ø6, ø10, ø16, ø20

Series MXH/ ø6, ø10, ø16, ø20 Compact Slide Series / ø, ø, ø, ø The use of an endless track linear guide produces a table cylinder having excellent rigidity, linearity and non-rotating accuracy. CL MLG CNA CNG MNB CNS CLS CB CV/MVG

More information

Mini Rotary Actuator/Rack & Pinion Style

Mini Rotary Actuator/Rack & Pinion Style Mini Rotary Actuator/Rack & Pinion Style Series CRJ :, CRB2 CRBU2 CRB MSU CRJ CRA CRQ2 MSQ MSZ CRQ2X MSQX MRQ PAT. PEND D- 79 Mini Rotary Actuator Series CRJ Rack & Pinion Style/:, Compact 9.5 23.5 43(54)

More information

Plate Cylinder. MU Series. It is possible to mount small auto switches in 4 directions. No stick-out Easy mounting. ø25, ø32, ø40, ø50, ø63

Plate Cylinder. MU Series. It is possible to mount small auto switches in 4 directions. No stick-out Easy mounting. ø25, ø32, ø40, ø50, ø63 Plate Cylinder MU Series ø, ø, ø, ø, ø It is possible to mount small auto switches in 4 directions. No stick-out Easy mounting RoHS Small auto switch CUJ CU CQS JCQ CQ2 Reduction of labor for work RQ CQM

More information

Slide Unit. Bore size. ø15 (2) ø10 (2) ø16 (3) ø20 (2) Ball bushing bearing Slide bearing. ø25 (3) (3) ø32 (3)

Slide Unit. Bore size. ø15 (2) ø10 (2) ø16 (3) ø20 (2) Ball bushing bearing Slide bearing. ø25 (3) (3) ø32 (3) Slide Unit Series CX/M/L Slide Bearing/CX:ø, ø, ø5 M:ø, ø6, ø0, ø5, ø3 Ball Bushing Bearing/L:ø, ø6, ø0, ø5, ø3 Provided with shock absorbers to absorb impact and noise. The slide unit can absorb energy

More information

Mini Rotary Actuator/Rack & Pinion Style

Mini Rotary Actuator/Rack & Pinion Style Mini Rotary Actuator/Rack & Pinion Style Series CRJ :, CRB2 CRBU2 CRB MSU CRJ CRA CRA CRQ2 MSQ MSZ CRQ2X MSQX MRQ PAT. PEND D- 79 Mini Rotary Actuator Series CRJ Rack & Pinion Style/:, Compact 9.5 23.5

More information

Elliptical design for space-savings

Elliptical design for space-savings Plate Cylinder Series,,,, By adopting an elliptical piston design, a slim, square shaped body has been achieved, resulting in a space-saving cylinder with unrestricted mounting directions. Elliptical design

More information

Basic type/direct mount type

Basic type/direct mount type Basic type/direct mount type Series / ø, ø, ø, ø, ø, ø, ø, ø, ø3 CYS -Z CYL CYH CYF CYP 443 D- -X Technical data Magnetically Coupled Rodless Cylinder Direct mount type Series / Basic type Improved durability

More information

Compact Cylinder. Series CQS CUJ CU CQS CQ2 RQ CQM MU

Compact Cylinder. Series CQS CUJ CU CQS CQ2 RQ CQM MU Compact Cylinder Series ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility for

More information

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP CT.S-7 C Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 New end lock type introduced to Series . Top mount Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Four mounting types

More information

Rotary Actuator/Vane Type

Rotary Actuator/Vane Type Rotary Actuator/Vane Type CRB2 Series : 1, 15, 2, 3, 4 Standard Type Free Mount Type Many combinations available! Standard type/crb2 Series Piping ports are located on the flat surface. Fittings can be

More information

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover.

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover. Air Cylinder 1 Series ø32, ø40, ø50, ø63, ø80, ø100, ø125 RoHS 10 (ø50-100 stroke) % lighter Current model 1.9 kg 1 Series 1.7 kg J 1 Reduced weight by changing the shape of the rod cover and head cover.

More information

How to Order. Standard stroke (mm) ø10 15, 30, 45, 60

How to Order. Standard stroke (mm) ø10 15, 30, 45, 60 ingle Acting, ingle Rod, pring Return/Extend eries K ø, ø pring extend pring return B L D Without auto switch With auto switch mm mm Basic Axial foot Rod side flange Double clevis K L CDJ2K L How to Order

More information

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil With auto switch RSG RSDG With auto switch (uilt-in magnet) uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the

More information

Mini Free Mount Cylinder

Mini Free Mount Cylinder Mini Free Mount Cylinder ø, ø, ø, ø, ø, ø1, ø Series CUJ Added ø, ø1, ø bore sizes. Action Double acting Single acting, spring return Double acting Single acting, spring return Double acting Single acting,

More information

69% 30.5 mm 16 mm. Compact Guide Cylinder. Compact. lighter 0.32 kga0.1 kg (Compared with the current MGP-Z series, ø16, 10 mm stroke) Weight

69% 30.5 mm 16 mm. Compact Guide Cylinder. Compact. lighter 0.32 kga0.1 kg (Compared with the current MGP-Z series, ø16, 10 mm stroke) Weight Compact Guide Cylinder ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 RoHS Compact Overall length shortened New s ø80, ø100 added. Port thread types NPT, G added. Height shortened JMGP ø32 25 mm stroke

More information

Rotary Actuated Air Gripper

Rotary Actuated Air Gripper Rotary ctuated ir Gripper MHR, MDHR/MHR3, MDHR3 -finger type: Size, 15,, 3/ 3-finger type: Size, 15 High Precision - Repeatability ±.1 mm Parallel opening and closing mechanism utilizing a cross roller

More information

Compact Hydraulic Cylinder

Compact Hydraulic Cylinder ompact Hydraulic ylinder Series HQ HQ Series HQ HK HN HM HS H2 H Nominal pressure:. MPa ore size :,,,,,, . MPa ompact Hydraulic ylinder Double cting/single Rod Series H Q ø, ø, ø, ø, ø, ø, ø With uto Switch

More information

Basic type / Direct mount type

Basic type / Direct mount type Basic type / Direct mount type Series / ø, ø, ø, ø, ø, ø, ø, ø, ø3 CYS CYL CY CYF Courtesy of Steven Engineering, Inc.- Ryan Way, South San Francisco, CA 0-30-Main Office: () -0-Outside Local Area: (00)

More information

Toggle Type Air Gripper

Toggle Type Air Gripper ø2, ø40, ø50, ø6 Ideal for gripping heavy workpiece Toggle mechanism is adopted. Holds workpiece even when pressure drops. The toggle mechanism that activates when the finger closes realizes strong and

More information

Dual-Rod Cylinder Compact Type

Dual-Rod Cylinder Compact Type CAT.ES-7 B Dual-Rod Cylinder Compact Type New Made to Order additionally released. (For details, refer to page 22.) Auto switch can be installed from 3 directions. Reverse Series CXSJ /ø, ø0, ø, ø, ø2,

More information

MHR3/MDHR3 Series. Rotary Actuated Air Gripper/3-Finger Type. Size: 10, 15 MDHR 3 10 R M9N S. How to Order. Without auto switch

MHR3/MDHR3 Series. Rotary Actuated Air Gripper/3-Finger Type. Size: 10, 15 MDHR 3 10 R M9N S. How to Order. Without auto switch Rotary ctuated ir Gripper/3-Finger Type MHR3/MDHR3 Series Size:, 1 How to Order Without auto switch MHR 3 R Connecting port R ody side R: ody side Port With auto switch (uilt-in magnet) MDHR 3 R M9N S

More information

Wedge Cam Operation Slide Guide. Air Gripper/2-Finger Type ø12, ø16, ø20, ø25. Option: Stainless steel

Wedge Cam Operation Slide Guide. Air Gripper/2-Finger Type ø12, ø16, ø20, ø25. Option: Stainless steel Wedge Cam Operation Slide Guide Air Gripper/2-inger Type ø2, ø, ø, ø2 MH MH oad Resistant, Dust Cover for Adverse Environments 2 types of finger materials types of dust cover materials Standard: Carbon

More information

180 Angular Style Air Gripper

180 Angular Style Air Gripper 18 Angular tyle Air Gripper eries 2/2 Cam tyle / Rack & Pinion tyle -X D- Courtesy of teven Engineering, Inc.-2 Ryan Way, outh an Francisco, CA 98-67-Main ffice: (6) 88-92-utside Local Area: (8) 28-92-www.stevenengineering.com

More information

Standard Type Dual-Rod Cylinder. ø6, ø10, ø15, ø20, ø25, ø32. How to Order

Standard Type Dual-Rod Cylinder. ø6, ø10, ø15, ø20, ø25, ø32. How to Order Standard Type ual-rod ylinder Series ø, ø, ø, ø, ø2, ø32 ompact Type J M L M earing type Slide bearing all bushing bearing How to Order 0 Y7W S Number of auto switches Nil 2 pcs. S pc. n "n" pcs. ore size/standard

More information

Rack & Pinion Type/Size: 30, 50, 63, 80, 100. Compact auto switches are mountable. (D-M9 ) Rotating angle. Rotating. angle

Rack & Pinion Type/Size: 30, 50, 63, 80, 100. Compact auto switches are mountable. (D-M9 ) Rotating angle. Rotating. angle Rotary Actuator Series Rack & Pinion Type/: 3, 5, 63, 8, 1 Compact auto switches are mountable. (D-M9 ) Width reduced by up to 14 mm Space saving by changing the auto switch rail mounting to groove mounting.

More information

Series MXU ø6, ø10, ø16

Series MXU ø6, ø10, ø16 Compact Slide Series ø, ø, ø1 Displacement accuracy against moments Table edge displacement M1(Pitch moment): 0.02mm or less M2(Yaw moment): 0.01mm or less The miniature linear guide improves the linear

More information

Compact Cylinder: Large Bore Size Type Double Acting, Double Rod. How to Order. Cushion C Rubber bumper. Action. D Double acting

Compact Cylinder: Large Bore Size Type Double Acting, Double Rod. How to Order. Cushion C Rubber bumper. Action. D Double acting Compact Cylinder: Large Bore Size Type Double Acting, Double Rod Series CQ2W ø, ø, ø, ø, ø Without auto switch With auto switch B Built-in magnet CQ2WB CDQ2WB Double rod ounting style Through-hole/Both

More information

Dual Rod Cylinder: Double Rod Type. How to Order. Load voltage Auto switch model Perpendicular In-line 3-wire (NPN equivalent) Y7NWV Y7NW 5 V, 12 V

Dual Rod Cylinder: Double Rod Type. How to Order. Load voltage Auto switch model Perpendicular In-line 3-wire (NPN equivalent) Y7NWV Y7NW 5 V, 12 V Dual Rod Cylinder: Double Rod Type eries CXW ø, ø, ø, ø, ø2, ø32 CX W L How to Order 0 Y7W M L Double rod type earing type lide bearing all bushing bearing ore size/troke ore size,,,,,,,,,,,,,,, 2, 32,

More information

Specifications MHC2-10D MHC2-16D MHC2-20D MHC2-25D MHC2-10S. Double acting MHC2-16S. Single acting MHC2-20S MHC2-25S. Angular style air gripper

Specifications MHC2-10D MHC2-16D MHC2-20D MHC2-25D MHC2-10S. Double acting MHC2-16S. Single acting MHC2-20S MHC2-25S. Angular style air gripper Angular Style Air Gripper Standard Type Series MHC2 Size: 10, 16, 20, 25 A large amount of gripping force is provided through the use of a double piston mechanism, while maintaining a compact design. Built-in

More information

Parallel Style Air Gripper

Parallel Style Air Gripper Parallel tyle Air Gripper eries MHZ MHZ MH -X D- Courtesy of teven Engineering, Inc.-3 Ryan Way, outh an Francisco, CA 98-37-Main Office: () 88-9-Outside Local Area: (8) 8-9-www.stevenengineering.com 373

More information

Low Profile Air Gripper

Low Profile Air Gripper Low Profile Air Gripper Series MHF2 MHZ MHF MHL MHR MHK MHS MHC MHT MHY MHW -X Low profile air gripper with space-saving design MRHQ MA D- Courtesy of Steven ngineering, Inc.-2 Ryan Way, South San Francisco,

More information

Air Cylinder: Standard Type Double Acting, Double Rod. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order. Bore size

Air Cylinder: Standard Type Double Acting, Double Rod. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order. Bore size Air Cylinder: tandard eries CG1W,,,,,,, 0 How to Order auto switch auto switch CG1W L N 0 With auto switch CDG1W L N 0 HW N A uilt-in magnet Double acting, double rod type L U Mounting style asic style

More information

Series MHK2. Wedge Cam Operation Slide Guide Air Gripper (2 Finger)

Series MHK2. Wedge Cam Operation Slide Guide Air Gripper (2 Finger) Wedge Cam Operation lide Guide Air Gripper (2 inger) ø2, ø, ø2, ø2 oad Resistant, Dust Cover for Adverse Environments 2 types of finger materials types of dust cover materials tandard: Carbon steel Optional:

More information

Rotary Actuator. New RoHS. Compact auto switches are mountable. Weight is reduced by up to 14 %. Mounting interchangeable with the current model

Rotary Actuator. New RoHS. Compact auto switches are mountable. Weight is reduced by up to 14 %. Mounting interchangeable with the current model Rotary Actuator Ø 30, Ø 50, Ø 63, Ø 80, Ø 100 New RoHS Compact auto switches are mountable. (D-M9 ) Width reduced by up to 14 mm Space saving by changing the auto switch rail mounting to groove mounting.

More information

Parallel Style Air Gripper

Parallel Style Air Gripper INFRMATIN Parallel tyle Air Gripper With Dust Cover Model variations with excellent dust proof and drip proof dust cover are expanded. MHZL2 Long stroke type MHZL2 series ø1, ø16 and ø2 with dust cover

More information

How to Order. Nil M. Action S T. Load voltage Wiring. M9NV 5 V, 12 V 3-wire (PNP) M9PV 12 V. F9NWV 5 V, 12 V 3-wire (PNP) F9PWV

How to Order. Nil M. Action S T. Load voltage Wiring. M9NV 5 V, 12 V 3-wire (PNP) M9PV 12 V. F9NWV 5 V, 12 V 3-wire (PNP) F9PWV ompact ylinder: Standard Type Single cting, Single Rod, Spring Return/Extend Series QS ø, ø, ø, ø How to Order QS S QS S FWV S uilt-in magnet Mounting style Through-hole/oth ends tapped common (Standard)

More information

Series MGP. Compact Guide Cylinder. New end lock type introduced to Series MGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100

Series MGP. Compact Guide Cylinder. New end lock type introduced to Series MGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 New end lock type introduced to Series.22- CL MLG CN CNG MNB CNS CLS CB CV/MVG CXW CXS CXT MX MXU MXH MXS MXQ MXF MXW MXP MG MGQ MGG MGC MGF

More information

Series RSH/RS1H. To stop pallets gently. Heavy Duty Stopper Cylinder. Stopper cylinder with built-in shock absorber. ø20, ø32 ø50, ø63, ø80

Series RSH/RS1H. To stop pallets gently. Heavy Duty Stopper Cylinder. Stopper cylinder with built-in shock absorber. ø20, ø32 ø50, ø63, ø80 1 eavy Duty Stopper Cylinder Series RS/RS1 ø, ø ø, ø, ø To stop pallets gently CX CY RC RS A MI S C G5-S Stopper cylinder with built-in shock absorber - -9-1 2 eavy Duty Stopper Cylinder Series RS/RS1

More information

Compact Guide Cylinder with Lock

Compact Guide Cylinder with Lock Compact Guide Cylinder with Lock Series,,,, ø,,, ø0 CLG CL CN2 MLC Drop prevention when the pressure of air source is decreased or the residual pressure is released. Drop prevention for press fitting jig

More information

49.5 mm Overall. 30 mm MXZ ø20. Compact. Compact Cylinder with Linear Guide. MXZ Series CAT.ES20-236A. ø12, ø16, ø20, ø25. MXZ ø20, 10 mm stroke.

49.5 mm Overall. 30 mm MXZ ø20. Compact. Compact Cylinder with Linear Guide. MXZ Series CAT.ES20-236A. ø12, ø16, ø20, ø25. MXZ ø20, 10 mm stroke. Compact Cylinder with Linear Guide ø12, ø16, ø20, ø25 RoHS Compact 49.5 mm Overall length MXZ ø20, 10 mm stroke 30 mm MXZ ø20 Width Design and assembly time is reduced due to integration of a linear guide

More information

Parallel Type Air Gripper/2 Finger, 3 Finger, 4 Finger

Parallel Type Air Gripper/2 Finger, 3 Finger, 4 Finger Parallel Type Air Gripper/ inger, inger, inger MHS Series ø1, ø, ø, ø, ø, ø, ø, ø, ø1, ø MHZ MH MH MHR MHK MHS MHC MHT MHY MHW -X MRHQ MA D- ightweight, compact design with reduced height High repeatability:

More information

Rod end male thread. With rubber bumper 056(9/16") 075(3/4") 106(1 1/16") 150(1 1/2") 250(2 1/2") 300(3")

Rod end male thread. With rubber bumper 056(9/16) 075(3/4) 106(1 1/16) 150(1 1/2) 250(2 1/2) 300(3) T.ID0-1 New ompact ylinder Series NQ8 ore size: 06(9/16 ),(/ ),106(1 1/16 ),(1 1/ ) 00( ),0( 1/ ),00( ),00( ) Now available in 00 ( ) and 00 ( ) bore sizes Standard type ctuation Style uilt-in magnet Rod

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary Actuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CRB2 CRBU2 CRB1 MSU CRJ CRA1 Rotation 360 type 360 MSZ MRQ Series Variations Page Rotating angle 80 to 0 170

More information

Low Profile Air Gripper

Low Profile Air Gripper Low Profile Air Gripper MHF2 Series ø8, ø, ø, ø RoHS Low profile air gripper with space-saving design MHZ MHF MHL MHR MHK MHS MHC MHT MHY MHW -X MRHQ MA D- 465 Low Profile Air Gripper MHF2 Series Height

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR2 CRU2 CR1 MSU CRJ Rotation 360 type MSQ 360 MSZ MSQ MRQ Series Variations Page Rotating angle 80 to 0 170

More information

3 Position Cylinder. RZQ Series. Provides intermediate stop mechanism. ø32, ø40, ø50, ø63. 2-stage stroke enabled with a small increase in length

3 Position Cylinder. RZQ Series. Provides intermediate stop mechanism. ø32, ø40, ø50, ø63. 2-stage stroke enabled with a small increase in length Position ylinder Series ø, ø, ø, ø Provides intermediate stop mechanism 2-stage stroke enabled with a small increase in length Overall length of cylinder tube DQ2 Full stroke First-stage stroke dditional

More information

Dual rod cylinder with guide function for pick & place applications.

Dual rod cylinder with guide function for pick & place applications. Dual Rod Cylinder Series CXS ø, ø0, ø, ø, ø2, Dual rod cylinder with guide function for pick & place applications. Series CXS Twice the thrust Non-rotating accuracy ±0. MX MY CY MG CX - Ball bushing bearings

More information

Non-rotating Double Power Cylinder. Double Power Cylinder MGZ. (without non-rotating MGJ MGP -Z MGP MGPW MGQ MGG MGC MGF MGT D- -X

Non-rotating Double Power Cylinder. Double Power Cylinder MGZ. (without non-rotating MGJ MGP -Z MGP MGPW MGQ MGG MGC MGF MGT D- -X Non-rotating Double Power Cylinder Double Power Cylinder (without non-rotating Series Series R mechanism) MGJ -Z W MGQ MGG MGC MGF MGT 23 D- -X Non-rotating Double Power Cylinder Double extension output

More information

MGZ. Non-rotating Double Power Cylinder. Double Power Cylinder MGJ MGP MGPW MGQ MGG MGC MGF MGT D- -X

MGZ. Non-rotating Double Power Cylinder. Double Power Cylinder MGJ MGP MGPW MGQ MGG MGC MGF MGT D- -X Non-rotating Double Power Cylinder Double Power Cylinder (without non-rotating Series Series R mechanism) 23 MGJ -Z W MGQ MGG MGC MGF MGT D- -X Tube rod diameter External dimension Non-rotating Double

More information

Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece

Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece ir Slide Table Series RoHS Height: mm/width: mm/length: mm () Traveling parallelism: 0.00 mm Note 1) Front mounting accuracy: 0.01 mm Note ) Top mounting accuracy: 0.0 mm Integrated front mounting part

More information

CJ1. Air Cylinder. Double Acting: ø4/single Acting, Spring Return: ø2.5, ø4 CJ1B 4 5 U4. How to Order/Double Acting

CJ1. Air Cylinder. Double Acting: ø4/single Acting, Spring Return: ø2.5, ø4 CJ1B 4 5 U4. How to Order/Double Acting Air Cylinder eries CJ1 ouble Acting: ø/ingle Acting, pring Return: ø2., ø eries Variations tandard eries CJ1 eries Action ouble acting ingle acting Mounting style asic style ingle rod ingle rod pring return

More information

Rotary Actuator/Vane Style

Rotary Actuator/Vane Style Rotary Actuator/Vane Style Series :,,,, Basic style Series With angle adjuster Series BWU Fluid Air, CR Vane type Port location Single vane (S) ouble vane () Side ported (Nil) Axial ported (E) S Side ported

More information

Dual-Rod Cylinder Compact Type

Dual-Rod Cylinder Compact Type CAT.EUS20-7 B -UK Dual-Rod Cylinder Compact Type New Made to Order additionally released. (For details, refer to page 22.) Auto switch can be installed from 3 directions. Reverse Series CXSJ/ø, ø0, ø,,

More information

Air Slide Table. Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece

Air Slide Table. Traveling parallelism: mm. Mounting from the through-holes on the top. Tapped for mounting a work piece ir Slide Table Series Height: mm/width: mm/length: mm () Front mounting accuracy: 0.01 mm Top mounting accuracy: 0.0 mm Traveling parallelism: 0.00 mm Note 1) Note ) Integrated front mounting part and

More information

Rotary Table/Vane Style

Rotary Table/Vane Style Rotary Table/Vane Style Series Size: 1, 3, 7, 20 Table top deflection mm or less High Precision Peripheral table deflection mm or less X Series B Series A 147 Rotary Table Values inside ( ) are for Series

More information

Electric Cylinder. LZB/LZC Series. It can be operated like an air cylinder. LZB Series. LZC Series LEF LEJ LEL LEM LEY LES LER LEH 25A- LEC

Electric Cylinder. LZB/LZC Series. It can be operated like an air cylinder. LZB Series. LZC Series LEF LEJ LEL LEM LEY LES LER LEH 25A- LEC Electric Cylinder LZB/LZC Series It can be operated like an air cylinder. LZB Series LZC Series Model LZB LZC Max. thrust Max. speed 196 N 0 mm/s Lead screw Slide screw: ø8, ø Lead: 2, 6, Stroke 25, 40,

More information

2 way basic mounting: Through-hole or both ends tapped

2 way basic mounting: Through-hole or both ends tapped Compact Cylinder Series CQS ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility

More information

Mini Free Mount Cylinder

Mini Free Mount Cylinder Mini Free Mount Cylinder ø, ø, ø, ø, ø, ø1, ø Series CUJ Added ø, ø1, ø bore sizes. Action Double acting Double acting Double acting Double acting Double acting Stroke 1 2 30 3 0 0 Clean series : New additions

More information

New cylinder body allows small auto switches to be mounted on 4 surfaces.

New cylinder body allows small auto switches to be mounted on 4 surfaces. Toggle Type Air Gripper ø32, ø4, ø5, ø63 New cylinder body allows small auto switches to be mounted on 4 surfaces. RoH Auto switch mounting rail removed. A round slot for mounting small auto switches is

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator CRQ2 Series Rack & Pinion Type/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR 2 CR1 MSU CRJ CR1 CRQ2 MSQ MSZ Rotation 360 type 360 CRQ2 MSQ MRQ Series Variations Page Rotating angle

More information

Air Gripper (2 Finger) (3 Finger)

Air Gripper (2 Finger) (3 Finger) Rotary Actuated Air Gripper ( Finger) (3 Finger) MHR/MDHR, MHR3/MDHR3 High Precision - Repeatability ±0.01mm Parallel opening and closing mechanism utilizing a cross roller guide produces smooth operation

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm 360 type 360 CR2 CRU2 CR1 MSU CRJ CR1 MSQ MSZ MSQ MRQ Series Variations Standard Made to Order Rotating angle

More information

C85 (ISO 6432) Series: ø8, ø10, ø12, ø16, ø20, ø25 C75 Series: ø32, ø40

C85 (ISO 6432) Series: ø8, ø10, ø12, ø16, ø20, ø25 C75 Series: ø32, ø40 ISO Cylinder (ISO 6432) Series: ø8, ø10, ø12, ø16, ø20, ø25 Series: ø32, ø40 RoS Part numbers set for actuators with mounting brackets, rod end brackets and auto switches available. Now it is not necessary

More information