Air Cylinder: With End Lock. How to Order. Cylinder stroke (mm) (Refer to Standard Stroke on page 250.) H Head end lock. Rod boot. Nil.

Transcription

1 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () With auto switch F G C D U CM CDM With auto switch (uilt-in magnet) Mounting style asic style xial foot style Rod side flange style T E Z Head side trunnion style Clevis integrated style oss-cut basic style Head side flange style oss-cut rod side FZ Single clevis style flange style Double clevis style oss-cut rod side UZ Rod side trunnion style trunnion style Clevis integrated style and boss-cut style are available only for locking on rod side. uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDM--H ir Cylinder: With End ock Series CM ø, ø, ø, ø ore size mm mm mm mm il How to Order H M9W C Cylinder stroke (Refer to Standard Stroke on page.) Cushion Rubber bumper ir cushion Manual release type Rod boot il J K H on-lock type ock type ock position H R W Double end lock one ylon tarpaulin Heat resistant tarpaulin pplicable uto Switches/Refer to pages 9 to 3 for further information on auto switches. il uto switch mounting bracket ote) ote) This symbol is indicated when the D-9 or M9 type auto switch is specified. This mounting bracket does not apply to other auto switches (D-C and H, etc.) (il) umber of auto switches il S n pcs. pc. n pcs. uto switch Without auto switch For the applicable auto switch model, refer to the table below. Made to Order (Refer to page for details.) Type Special function Electrical oad voltage ead wire length (m) Wiring uto switch model Pre-wired pplicable entry (Output). 3 DC C (il) (M) () (Z) one () connector load Perpendicular In-line 3-wire (P) M9V M9 V, V Grommet 3-wire (PP) M9PV M9P M9V M9 -wire V Connector HC Terminal 3-wire (P) V, V G39 conduit -wire V K39 Relay, 3-wire (P) 4 V M9WV M9W Diagnostic indication V, V PC 3-wire (PP) M9PWV M9PW (-color indication) -wire V M9WV M9W Grommet 3-wire (P) M9V M9 Water resistant V, V 3-wire (PP) M9PV M9P (-color indication) -wire V M9V M9 With diagnostic output (-color indication) 4-wire (P) V, V HF 3-wire (P equivalent) V 9V 9 Grommet V 93V 93 V or less 9V 9 V, V 4 Relay, V or less 4 PC Connector -wire 4 V V C3C 4 V or less CC Terminal 33 PC conduit V, Relay, DI terminal V 44 PC Diagnostic indication (-color indication) Grommet 9W 34 Reed auto switch Solid state auto switch Indicator light Yes Yes o Yes o Yes o Yes Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Consult with SMC regarding water resistant types with the above model numbers. ead wire length symbols:. m il (Example) M9W m M (Example) M9WM Solid state auto switches marked with are produced upon receipt of order. Do not indicate suffix for no lead wire on D-3/44/G39/K39 models. 3 m (Example) M9W D-3/44/G39/K39/4/4 cannot be mounted on bore sizes ø and m Z (Example) M9WZ ø cylinder with air cushion. one (Example) HC Since there are other applicable auto switches than listed above, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages and. D-9/M9 auto switches are shipped together (not assembled). (However, auto switch mounting brackets are assembled when being shipped.) 49 CJ CJP CJ CJ CM CM CM3 CG3 M M M C C CS CS D- -X Technical data

2 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Series CM Holds the cylinder s home position even if the air supply is cut off. When air is discharged at the stroke end position, the lock engages to maintain the rod in that position. on-lock type and lock type are standardized for manual release. uto switch is mountable. Symbol Rubber bumper Symbol ir cushion Specifications -X Change of rod end shape -X Heat resistant cylinder ( C) -X9 ow speed cylinder ( to mm/s) -XC3 Special port location -XC4 With heavy duty scraper -XC Heat resistant cylinder ( C) -XC Piston rod and rod end nut made of stainless steel -XC djustable stroke cylinder/djustable extension type -XC3 uto switch mounting rail style -XC Fluororubber seals -XC o fixed orifice of connecting port -XC Double clevis pin and double knuckle pin made of stainless steel -XC9 Double knuckle joint with spring pin -XC3 With coil scraper -XC Mounting nut with set screw vailable only for locking at head end Made to Order Specifications (For details, refer to pages to.) Specifications ore size Type ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure Pneumatic Double acting, Single rod ir. MPa. MPa. MPa mbient and fluid temperature Cushion ubrication Stroke length tolerance Piston speed Mounting. MPa for other part than the lock unit ock Specifications ock position Holding force (Max.) () acklash Manual release llowable Kinetic Energy Rubber bumper ir cushion Standard Stroke ore size ore size llowable kinetic energy (J) Effective cushion length Cushion sectional area (cm ) Kinetic energy absorbable (J) Standard stroke,,,,,,, 3 Rubber bumper, ir cushion ot required (on-lube) +.4 mm Rubber bumper to mm/s ir cushion to mm/s asic style, xial foot style, Rod side flange style, Head side flange style, Single clevis style, Double clevis style, Rod side trunnion style, Head side trunnion style ø Head end, Rod end, Double end ø ø 33 mm or less on-lock type, ock type ong stroke ø Maximum manufacturable stroke ong stroke applies to the axial foot style and the rod side flange style only. When using other types of mounting brackets or exceeding the long stroke limit, the maximum allowable stroke will be determined by the stroke selection table listed on front matter. Manufacture of intermediate strokes at mm intervals is possible. (Spacers are not used.) Refer to pages 9 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket: Part no.

3 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () ccessory/for details, refer to pages and 9, since it is the same as Series CM standard type. Standard equipment Option Mounting nuts are not equipped to single clevis and double clevis. Weight ore size asic style xial foot style asic Flange style weight Single clevis Double clevis style Trunnion style dditional weight per each mm of stroke ccessory (kg) ock Unit dditional Weight (kg) ore size Manual release non-lock type () Manual release lock type () (H) (R) Double end lock (W) (H) (R) Double end lock (W) Calculation: (Example) CM--H asic weight.44 (Foot style, ø) dditional weight./ stroke Cylinder stroke stroke ocking weight. (ocking at head end, Manual release non-locking type) x / +. =. kg Min. order Mounting nut, Rod end nut, Clevis pin, ock release bolt ( type only) Single knuckle joint, Double knuckle joint (With pin) Clevis bracket (With pin) Single knuckle joint Double knuckle joint (With pin) Mounting racket Part o. Mounting bracket xial foot Flange Single clevis Double clevis (With pin) Trunnion (With nut) ore size CM- CM- CM- CM-F CM-F CM-F CM-C CM-C CM-C CM-D CM-D CM-D CM-T CM-T CM-T Order foot brackets for each cylinder unit. 3 iners are attached with a clevis bracket for adjusting the mounting angle. Clevis pins and retaining rings (cotter pins for ø) are attached. ir Cylinder: With End ock Series CM Description (for min. order) foot, mounting nut flange single clevis, 3 liners double clevis, 3 liners, clevis pin, retaining rings trunnion, trunnion nut Rod oot Material Symbol J K Rod boot material ylon tarpaulin Heat resistant tarpaulin Maximum ambient temperature for the rod boot itself. CJ CJP CJ CJ CM CM CM3 CG3 M M M C C CS CS D- -X Technical data

4 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Series CM Double Rod Type End ock Cylinder CMW Mounting style ore size Specifications Double rod type end lock cylinder ction Double acting, Double rod ore size ø, ø, ø, ø Max. operating pressure. MPa Min. operating pressure. MPa Cushion Rubber bumper Piston speed to mm/s Mounting asic style, Foot style, Flange style, Trunnion style ock position Maximum manufacturable stroke mm ote ) uto switch can be mounted. ote ) Refer to the Precautions on page when mounting flanges and trunnion brackets on the end lock side. ote 3) When exceeding 3 strokes, the allowable maximum stroke length is determined by the stroke selection table (front matter 34). H Stroke on-rotating Rod Type End ock Cylinder CMK Mounting style ore size Stroke on-rotating rod type end lock cylinder Specifications ction Double acting, Double rod ore size ø, ø, ø, ø Max. operating pressure. MPa Min. operating pressure. MPa Cushion Rubber bumper Piston speed to mm/s asic, foot, rod side flange, head side flange, single clevis, Mounting double clevis, rod side trunnion, head side trunnion ock position Maximum manufacturable stroke mm ote ) uto switch can be mounted. ote ) Refer to the Precautions on page for the head side flange and head side trunnion styles. ote 3) When exceeding 3 strokes, the allowable maximum stroke length is determined by the stroke selection table (front matter 34). Width across flats K H Manual release type ZZ + x stroke Dimensions ore size H ZZ Dimensions for other bore sizes are the same as the double acting single rod model. H Manual release type Dimensions H + stroke ore size K Dimensions for other bore sizes are the same as the double acting single rod model.

5 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Construction Manual release (on-lock type): Suffix Component Parts o Description Rod cover Head cover Cylinder tube Piston Piston rod ushing Seal retainer Retaining ring ock piston ock bushing ock spring umper Hexagon socket head cap screw Cap Cap Rubber cap M/O knob M/O bolt M/O spring Stopper ring umper umper Retaining ring Piston seal Piston gasket Wear ring Mounting nut Rod end nut Cushion ring Cushion needle Cushion seal With air ir Cylinder: With End ock Series CM # # Component Parts Manual release (ock type): Suffix Material ote o. Description Material ote luminum alloy luminum alloy Stainless steel Clear anodized Clear anodized 33 Rod seal ock piston seal Cushion needle seal R R R luminum alloy Chromated Carbon steel Hard chrome plated earing alloy Replacement Parts: Seal Kit Stainless steel With lock in single end Carbon steel Phosphate coated ore size Hard chrome plated, Carbon steel Heat treated earing alloy Kit no. CM--PS CM--PS CM--PS CM--PS Stainless steel With lock at double ends Urethane Kit no. CM--PS CM--PS CM--PS CM--PS lloy steel lack zinc chromated Seal kit Order the seal kit, based on each bore size. (Except #3.) luminum die-casted lack painted Seal kit includes a grease pack ( g). Order with the following part Carbon steel Oxide film treated number when only the grease pack is needed. Synthetic rubber Grease pack part number: GR-S- ( g) Zinc die-casted lack painted lloy steel lack zinc chromated Steel wire Zinc chromated How to Change Seal Kit Carbon steel Zinc chromated <Removal> Urethane Remove the retaining ring () by using a tool for installing a type C Urethane retaining ring for hole. Shut off the port on the rod cover by finger and then pull out the piston rod, and the seal retainer () and the Stainless steel rod seal (C) are removed. Port R <Mounting> R fter applying enough grease on Resin the rod seal, attach in this order, Carbon steel ickel plated rod seal (C), seal retainer () and Carbon steel Zinc chromated retaining ring (). luminum alloy nodized lloy steel Electroless nickel plated (C) Rod seal Urethane () Seal retainer () Retaining #3 # 3 CJ CJP CJ CJ CM CM CM3 CG3 M M M C C CS CS D- -X Technical data

6 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Series CM asic Style (Dimensions are common irrespective of the lock position; rod end, head end, or double end.) : CM ore size Width across flats Width across flats ød H MM Width across flats K H G K F H x RcP : CM ore size S + Stroke ZZ + Stroke Double end lock: CM ore size Stroke -H D G Stroke F Stroke øe ø h ZZ + Stroke f øi HR H ø Manual release (on-lock type): Suffix Symbol Stroke H ore size D D F F G H H H range E HR (Max.) I K K MM MO P S ZZ Up to M x. 4 M x..33 Up to M x. 3 M x..33 Up to M x. 34. M x Up to M4 x M x With Rod oot Symbol h ore size 3 e f to to to to to 3 3 to to to to to to to 3 3 to to With Rod oot Symbol ZZ ore size to to to to to 3 3 to to JH JW For details about the rod end nut and accessory, refer to pages and 9. 4 x x øeh Effective thread length x F With rod boot Width across flats 3 D ømo Manual release (ock type): Suffix JH JW

7 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () With Mounting racket (For dimensions not indicated below, refer to page 4.) xial foot style: CM ore size C TX TZ T øtd øty Z Y X FX FZ Z FT ø ø to ø -H Single clevis style: CMC ore size Stroke Z ZZ FY Z ZZ TT Z S + Stroke ZZ + Stroke + Stroke + Stroke + Stroke + Stroke Stroke Rod side flange style: CMF ore size x øfd Mounting hole 4 x øfd Mounting hole Double clevis style: CMD ore size Rod side trunnion style: CMU ore size ore size Stroke range xial foot style Stroke range C D H S T X Z X Y Z ZZ Rod side Head side -H ZZ + Stroke X Stroke Stroke U to to 4 4 to Up to Up to Up to 4 Up to Up to 4 Up to to Up to Up to Dimensions other than mentioned above are the same as on page 4. U 4 x ød Y -H RR -H Stroke. Trunnion style a With lock in rod side of the rod side trunnion style s With lock in head side of the head side trunnion style d With lock in both sides. For above cases, use caution since the trunnion pin and fittings may be interfered with each other because the trunnion pin and port are very closed to each other ir Cylinder: With End ock Series CM RR øcd -H CX øcd hole H xis d9 x øc CX CZ X Z H ø ø Head side flange style: CMG ore size Stroke Z + Stroke Head side trunnion style: CMT ore size Stroke Z + Stroke ZZ + Stroke -H FT Clevis pin and retaining ring (cotter pin for bore size ø) are shipped together. -H TT The bracket is shipped together. Flange style Clevis style Trunnion style Z Stroke Stroke Z ZZ C FD FT FX FY FZ range CD CX CZ RR U Z ZZ TD TT TX TY TZ Rod side Head side range Rod side Head side Rod side Head side 3 Up to Up to Up to Up to Up to Up to Up to Up to Precautions on Trunnion Style, Flange Style. Flange style (ø to ø) a With lock in rod side of the rod side flange style s With lock in head side of the head side flange style d With lock in both sides. For above cases, use caution since the bolt for mounting a cylinder and fittings may be interfered with each other. Refer to Special Port Position in Made to Order Specifications on page. CJ CJP CJ CJ CM CM CM3 CG3 M M M C C CS CS D- -X Technical data

8 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Series CM With ir Cushion (For dimensions not indicated below, refer to pages 4 and.) asic style : CM ore size With ir Cushion ore size The bracket is shipped together S Z 44 4 W xial foot style: CM ore size Rod side flange style: CMF ore size Double end lock Double end lock 4 9 Stroke -H Stroke W -H Stroke ZZ ZZ H Double end lock 4 Double end lock 3 Head side flange style: CMG ore size Stroke 4 4. Z + Stroke ZZ + Stroke Head side flange style Z 4 Z 9 3. Double end lock Double end lock H Single clevis style: CMC ore size Stroke -H Double clevis style: CMD ore size Stroke -H +. Z + Stroke +. ZZ + Stroke Rod side trunnion style: CMU ore size Stroke ore size ore size S W W ZZ Double end lock Double end lock Double end lock S + Stroke ZZ + Stroke S + Stroke ZZ + Stroke -H Head side trunnion style: CMT ore size Stroke xial foot style Clevis style Cushion needle (Width across flats.) 4 ø Manual release (on-lock type): Suffix Z + Stroke +. Z + Stroke +. ZZ + Stroke -H Head side trunnion style 3 33 ZZ Double end lock Double end lock

9 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Use the Recommended Pneumatic Circuit Caution W Series CM Specific Product Precautions e sure to read before handling. Refer to front matter for Safety Instructions and pages 3 to for ctuator and uto Switch Precautions. This is necessary for proper operation and release of the lock. Caution Operating Precautions W. Do not use 3 position solenoid valves. void use in combination with 3 position solenoid valves (especially closed center metal seal types). If pressure is trapped in the port on the lock mechanism side, the cylinder cannot be locked. Furthermore, even after being locked, the lock may be released after some time, due to air leaking from the solenoid valve and entering the cylinder.. ack pressure is required to release end lock. e sure air is supplied to side of cylinder without the locking mechanism, as above, prior to supplying air pressure to the side with end lock or lock may not be released. (Refer to Releasing the ock.) 3. Release the lock when mounting or adjusting the cylinder. If mounting or other work is performed when the cylinder is locked, the lock unit may be damaged. 4. Operate with a load ratio of % or less. If the load ratio exceeds %, this may cause problems such as failure of the lock to release, or damage to the lock unit.. Do not operate multiple cylinders in synchronization. void applications in which two or more end lock cylinders are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required.. Use a speed controller with meter-out control. ock cannot be released occasionally by meter-in control.. e sure to operate completely to the cylinder stroke end on the side with the lock. If the cylinder piston does not reach the end of the stroke, locking might not work or locking might not be released.. The base oil of grease may seep out. The base oil of grease in the cylinder may seep out of the tube, cover, or crimped part depending on the operating conditions (ambient temperature C or more, pressurized condition, low frequency operation). Caution Caution Caution Warning Operating Pressure. Use pressures over. MPa at port with locking mechanism. Exhaust Speed. ocking will occur automatically if the pressure applied to the port on the lock mechanism side falls to. MPa or less. In cases where the piping on the lock mechanism side is long and thin, or the speed controller is separated at some distance from the cylinder port, the exhaust speed will be reduced. Take note that some time may be required for the lock to engage. In addition, clogging of a silencer mounted on the solenoid valve exhaust port can produce the same effect. Relation to Cushion. When cushion valve at side with locking mechanism is fully opened or closed, piston rod may reached at stroke end. Thus lock is not established. nd when locking is done at cushion valve fully closed, adjust cushion valve since lock may not be released. Releasing the ock. efore releasing the lock, be sure to supply air to the side without the lock mechanism, so that there is no load applied to the lock mechanism when it is released. (Refer to the recommended pneumatic circuits.) If the lock is released when the port on the other side is in an exhaust state, and with a load applied to the lock unit, the lock unit may be subjected to an excessive force and be damaged. Furthermore, sudden movement of the piston rod is very dangerous. CJ CJP CJ CJ CM CM CM3 CG3 M M M C C CS CS D- -X Technical data

10 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Manual Release Working Principle Caution. Manual release (on-lock type) Insert the accessory bolt from the top of the rubber cap (it is not necessary to remove the rubber cap), and after screwing it into the lock piston, pull it to release the lock. If you stop pulling the bolt, the lock will return to an operational state. Thread sizes, pulling forces and strokes are as shown below. ore size,, Remove the bolt for normal operation. It can cause lock malfunction or faulty release.. Manual release (ock type) While pushing the M/O knob, turn it 9 counterclockwise. The lock is released (and remains in a released state) by aligning the mark on the cap with the OFF mark on the M/O knob. When locking is desired, turn M/O button clockwise 9 while pushing fully, correspond on cap and O mark on M/O button. The correct position is confirmed by a click sound click. If not confirmed, locking is not done. ocked Series CM Specific Product Precautions e sure to read before handling. Refer to front matter for Safety Instructions and pages 3 to for ctuator and uto Switch Precautions. Thread size Pulling force M. x.4 x or more 4.9 M3 x. x 3 or more Unlock Rubber cap ock Released Stroke 3 The figures below are for Series C. ( is the same, too.). When the piston rod is getting closer to the stroke end, the taper part () of the piston rod edge will push the lock piston up. Spring Pressure Piston rod. ock piston is pushed up further. 3. ock piston is pushed up into the groove of piston rod to lock it. (ock piston is pushed up by spring force.) t this time, it is exhausted from port in head side and introduced to atmosphere. ocked 4. When pressure is supplied in the head side, lock piston will be pushed up to release the lock. Exhaust Released ack pressure ock piston. ock will be released, then cylinder will move forward. Exhaust Pressure

11 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Reed auto switch D-9 HS D-9V HS D-C/C D-//9W D-33/34 D-44 D-C3C/CC Series CM uto Switch Mounting Proper uto Switch Mounting Position (Detection at stroke end) and Its Mounting Height 4. () ( ): Values for D-9 and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. uto switch uto switch uto switch uto switch G / (pplicable cable O.D. ø. to ø9.) uto switch G / (pplicable cable O.D. ø. to ø.) Solid state auto switch D-M9/D-M9W/D-M9 HS D-M9V/D-M9WV/D-M9V HS D-H/HW/HF/H D-GT D-G39/K39 D-HC ( ): Values for D-M9 and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. ( ): Values for D-M9V and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. (4) () uto switch uto switch uto switch uto switch G / (pplicable cable O.D. ø. to ø9.) 9 CJ CJP CJ CJ CM CM CM3 CG3 M M M C C CS CS D- -X Technical data

12 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Series CM Proper uto Switch Mounting Position (Detection at stroke end) and Its Mounting Height Proper uto Switch Mounting Position (Excluding Single cting Type) uto switch model D-9(V) D-9 D-M9 D-M9W D-M9 Hs... D-M9(V) D-M9W(V) D-M9(V) D- D-4 D-9W D-GT D-HC Hs D- D-4 D-C D-C D-H D-HW D-H D-HF Hs... D-C D-C D-C3C D-CC ore size (4) (3) () () () () () (4) () () () (4) () (3) (4) () (9) () () () () () () () () (4) () () (3) () () () () ( ): Setting position for the auto switch with an air cushion. D-//3/44/G39/K39 cannot be mounted on the bore size ø and ø cylinder with an air cushion. ote) djust the auto switch after confirming the operating condition in the actual setting. uto Switch Mounting Height uto switch model ore size D-9V D-M9V D-M9WV D-M9V Hs D-C3C D-CC Hs. 3 3 D-9W D-3 D-G39 D-K39 Hs. D-44 Hs D-3 D-G39 D-K39 D-44 () (). (). D-H D-HC D-HW D-H D-HF (4) (4) () (3) (3) (4) D-GT. (.). (.) 3. (.).. (). (). (.).

13 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Proper uto Switch Mounting Position (Detection at stroke end) and Mounting Height: Single cting/spring Return Type (S), Spring Extend Type (T) Proper uto Switch Mounting Position: Standard Type/Spring Return Type (S), on-rotating Rod Type/Spring Return Type (S) uto switch model ore size Dimensions Up to st to st to st to st to st 3... D-9(V) D-M9(V) 3... D-M9W(V) D-M9(V) D- D-4 D-C D-C D-C3C D-CC D-9W D-3 D-G39 D-K39 D-44 D-H D-HC 3 D-HW D-H D-HF D-GT uto Switch Mounting Series CM Proper uto Switch Mounting Position: Standard Type/Spring Extend Type (T), on-rotating Rod Type/Spring Extend Type (T) uto switch model ore size Dimensions Up to st to st to st to st to st D-9(V) D-M9(V) D-M9W(V) D-M9(V) D- D-4 D-C D-C D-C3C D-CC D-9W D-3 D-G39 D-K39 D-44 D-H D-HC 3 D-HW D-H 3 D-HF D-GT.... ote) djust the auto switch after confirming the operating condition in the actual setting ote) djust the auto switch after confirming the operating condition in the actual setting. CJ CJP CJ CJ CM CM CM3 CG3 M M M C C CS CS D- -X Technical data

14 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () Series CM Minimum uto Switch Mounting Stroke uto switch model D-M9 D-M9W D-M9 D-9 D-M9V D-9V D-M9WV D-M9V D-C D-C D-H D-HW D-H D-HF D-C3C D-CC D-HC D-/4 D-GT D-9W D-3 ote ) D-G39 D-K39 D-44 ote ) uto switch mounting uto switch model D-M9 D-M9W D-M9 D-9 Operating range uto switch model pc. ore size o. of auto switch mounted pcs. Different surfaces Same surface 3 Different surfaces 3. The proper auto switch mounting position is 3. mm inward from the switch holder edge. ote ) Minimum stroke for auto switch mounting in styles other than those in ote. D-9(V) D-M9(V) D-M9W(V) D-M9(V) D-C/C D-C3C/CC 3 3 With auto switches 3 + 3(n ) (n =, 3, 4, ) n: o. of auto switch n pcs. Different surfaces Same surface (n ) (n ) (n =, 4, ) ote 3) (n =, 3, 4, ) (n ) (n ) (n =, 4, ) ote 3) (n =, 3, 4, ) (n ) (n ) (n =, 4, ) ote 3) (n =, 3, 4, ) (n ) (n ) (n =, 4, ) ote 3) (n =, 3, 4, ) (n ) (n ) (n =, 4, ) ote 3) (n =, 3, 4, ) (n ) (n ) (n =, 4, ) ote 3) (n =, 3, 4, ) (n ) (n ) (n =, 4, ) ote 3) (n =, 3, 4, ) (n ) (n ) (n =, 4, ) ote 3) (n =, 3, 4, ) (n ) + 4 (n =, 4, ) ote 3) (n ) + (n =, 4, ) ote 3) (n ) + (n =, 4, ) ote 3) (n ) + (n =, 4, ) ote 3) Same surface The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. ess than stroke ote ) ess than stroke ote ) ess than stroke ote ) ess than stroke ote ) ess than stroke ote ) + 4(n ) (n =, 3, 4, ) + (n ) (n =, 3, 4, ) + (n ) (n =, 3, 4, ) + (n ) (n =, 3, 4, ) + (n ) (n =, 3, 4, ) ote 3) When n is an odd number, an even number that is one larger than this odd number is used for the calculation. uto switch model D-/4 D-3/44 ote) D-9W D-H/HW/H D-GT/HF D-HC D-G39/K39 ote) ore size Since this is a guideline including hysteresis, not meant to be guaranteed. (ssuming approximately ±3% dispersion.) There may be the case it will vary substantially depending on an ambient environment. ote) D-3/44/G39/K39 cannot be mounted on the centralized piping type Series CDMP

15 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () uto Switch Mounting racket: Part o. uto switch model D-M9(V) D-M9W(V) D-9(V) D-M9(V) D-H D-HW D-HF D-C/C D-C3C/CC D-H D-/4 D-9W D-GT D-G D-3/44 D-G39/K39 ote ) ø - M3- ore size ø ø - M3- - M3- ø - M3- ote ) Set part number which includes the auto switch mounting band (M-) and the holder kit (J-/Switch bracket: Transparent). ote ) Set part number which includes the auto switch mounting band (M-S) and the holder kit (J4-/Switch bracket: White). ote 3) D-3/44/G39/K39 cannot be mounted on the centralized piping type Series CDMP. ote 4) For the D-M9(V) type auto switch, do not install the switch bracket on the indicator light. a Switch bracket (Resin) b Switch holder (Zinc) ote ) M- ote ) M-S M- M-S uto switch ote ) M- ote ) M-S M- M-S c uto switch mounting band ote ) M- ote ) M-S M- M-S d uto switch mounting screw ote ) M- ote ) M-S M- M-S qm-(s): set of c and d in the figure. wj-: set of a and b in the figure. J4- (Switch bracket: White) J- (Switch bracket: Transparent) In addition to the auto switches listed above, the following auto switches are also available. Refer to pages 9 to 3 for the detailed specifications. uto switch type Part no. Electrical entry (Entry direction) Features Solid state Reed D-H, H, H D-HW, HPW, HW D-H D-GT D-3, C3, C D-C Grommet (In-line) Grommet (In-line) Diagnostic indication (-color indication) Water resistant (-color indication) With timer Without light Solid state auto switches are also available with a pre-wired connector. Refer to pages and for details. ormally closed (C = b contact) solid state auto switches (D-F9G/F9H types) are also available. Refer to page for details. wide range detection type, solid state auto switch (D-G type) is also available. Refer to page 9 for details. uto Switch Mounting Series CM 3 CJ CJP CJ CJ CM CM CM3 CG3 M M M C C CS CS D- -X Technical data

16 ow Speed Cylinder Double cting, Single Rod Series CMX ø, ø, ø, ø Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () F G C D U asic style xial foot style Rod side flange style Head side flange style Single clevis style Double clevis style Rod side trunnion style With auto switch T E Z FZ UZ With auto switch (uilt-in magnet) Mounting style Head side trunnion style Clevis integrated style oss-cut basic style oss-cut rod side flange style oss-cut rod side trunnion style CMX CDMX ow speed cylinder uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDMXF- Grommet Connector Terminal conduit Grommet ead wire length symbols:. m il (Example) M9W m M (Example) M9WM 3 m (Example) M9W m Z (Example) M9WZ one (Example) HC Yes Yes Grommet o Yes o Yes Connector o Terminal conduit Yes DI terminal Diagnostic indication (-color) Grommet 3-wire (P) 3-wire (PP) -wire 3-wire (P) -wire 3-wire (P) 3-wire (PP) -wire 4-wire (P) 3-wire (Equiv. P) -wire 4 V 4 V M9W ore size mm mm mm mm V, V V V, V V V, V V V, V V V Cylinder stroke Refer to "Standard Stroke" on page 49. Thread type il Rc T PT TF G pplicable uto Switch/Refer to pages 9 to for further information on auto switches. Type Reed switch Solid state switch Special function Diagnostic indication (-color) With diagnostic output (-color) Electrical entry Indicator light How to Order Wiring oad voltage (Output) DC C umber of auto switches il pcs. S pc. n n pcs. uto switch il Without auto switch For the applicable auto switch model, refer to the table below. Solid state auto switches marked with are produced upon receipt of order. D-9V/M9V/M9WV/M9(V) types cannot be mounted. Do not add the suffix () indicating no lead wire to the part numbers of models D-3, 44, G39 and K39. In addition to the models in the above table, there are some other auto switches that are applicable. For more information, refer to page. Refer to pages 4 and for details of auto switches with a pre-wired connector. D-9/M9/M9W auto switches are shipped together (not assembled). (Only auto switch mounting brackets are assembled before shipped.) V V or less V, V V or less 4 V or less V, V uto switch model M9 M9P M9 HC G39 K39 M9W M9PW M9W HF C3C CC W. (il) ead wire (m) (M) 3 () one (Z) () Pre-wired connector pplicable load Relay, PC Relay, PC PC Relay, PC 4