Series NCM. Air Cylinder. Stainless Steel Body Cylinders 7/16", 9/16", 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2", 2" Bore

Transcription

1 CT.ID2-2 ir Cylinder Series CM Stainless Steel ody Cylinders 7/16", 9/16", 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2", 2" ore ow available in 7/16" and 9/16" bore Double Rod/Double End Mounting on-rotating Rod ption uto Switch Capable Standard type ctuation Style uto switch capable onrotating rod ith bumper ore size Standard stroke Double acting Single rod 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") [ore size 44/56] 5 (1/2"), 1 (1"),, 2 (2"), 25 (2-1/2"), 3 (3"), 4 (4") [ore size 75 and above] 5 (1/2"), 1 (1"),, 2 (2"), 25 (2-1/2"), 3 (3"), 4 (4"), 6 (6") Double acting Double rod 88 (7/8") 2 (2") 5 (1/2"), 1 (1"),, 2 (2"), 25 (2-1/2"), 3 (3"), 4 (4"), 6 (6") Single acting Single rod 88 (7/8") 5 (1/2"), 1 (1"), 2 (2"), 3 (3"), 4 (4"), 5 (5") 6 (6")

2 ir Cylinder Series CM ow available in 8 different bore sizes, 7/16" to 2". 5 ctuation options available: Double cting, Single Rod Double cting, Double Rod on-rotating Rod Single cting, Spring Return Single cting, Spring Extend wide variety of mounting configurations: ront ose Mount Rear Pivot Mount Double End Mount lock Mount oot Mount (optional brackets) Chrome plated carbon steel piston rod improves corrosion resistance. Stainless steel 34 is available for further protection. vailable bumper for increased kinetic energy absorption, increased life cycles, and decreased noise. Piston is crimped to rod to achieve tighter clearances and reduce piston rod deflection. Chromated aluminum piston improves corrosion resistance. Magnetic actuated limit switches are available as a standard option. Seal, wear ring, and polished stainless steel tube work together to absorb side load and decrease overall friction, ensuring long lasting service life. (ear ring used on 3/4" bore and larger.) ull port design increases cylinder response. Rolled threads for increased strength. Clear anodized end covers provide long lasting protection against corrosion. Pre-lubricated at the factory means that the CM does not require a lubricated air system. eatures 1

3 Series CM ir Cylinder Model Selection Step 1 btain the bore of the cylinder tube. Refer to Graph (1) and (2). Determine the load factor in accordance with the purpose. Purpose of operation oad factor η Static operation (Clamping, ow-speed vise crimping, etc.) Dynamic operation Horizontal movement of load on guide Vertical and horizontal movement of the load.7 or less (7% or less) 1 or less (1% or less).5 or less (5% or less) ote) ote) If it is particularly necessary to operate at high speeds, the load rate must be reduced further. (In the graph, it is possible to select a load rate of.4,.3,.2 or less.) Determine the operating pressure. Generally, set the regulator to 85% of the source air pressure. (In the graph, a selection between.2 MPa and.8 MPa is possible.) Determine the direction in which the cylinder force will be used. Extending side Refer to Graph (1). Retracting side Refer to Graph (2). ote) If the same load is applied both for pushing and pulling in a horizontal operation, set the direction to the pulling side. Step 3 Step 4 The aspects indicated below may need to be taken into consideration, depending on how the cylinder is operated. If a lateral load is applied to the piston rod: Verify in Graph (5) whether the lateral load is within an allowable range. hen using a cylinder with a relatively long stroke, if a buckling force acts on the piston rod or the cylinder tube, verify in the table whether the stroke or the operating pressure is within a safe range. btain the cylinder s air consumption and its required air volume. btain the air consumption selecting a compressor and for calculating the running cost and the required (Graph (6) to (7)) that is necessary for selecting a compressor and for calculating the running cost and the required air volume (Graph (8)) that is necessary for selecting equipment such as an air filter or a regulator, or the size of the piping upstream. Step 2 Take the impact at the stroke end into consideration. hen an external stopper (shock absorber, etc.) is provided to absorb the impact, select a stopper with sufficient absorption capacity. Stopping the piston with the cylinder without a stopper: Verify in Graph (3) to (4) the absorption capacity of the cushion that is enclosed in the cylinder. umper Urethane rubber is used for preventing metal-tometal contact between the piston and the cover. ront matter 1

4 Model Selection Step 1 btain the bore of the cylinder tube. Refer to Graph (1) and (2). Graph (1) Extending Side Cylinder orce (Double acting cylinder) Graph (2) Retracting Side Cylinder orce (Double acting cylinder) 1 1. Cylinder force (lbf) 1 CM2 CM15 CM125 CM16 CM88 CM75 Cylinder force (lbf) 1. CM2 CM15 CM125 CM16 CM88 CM75 CM56 1 CM44 1. CM56 CM44 perating pressure (PSI) oad factor (n) perating pressure (PSI) oad factor (n) (Example) P = 75 PSI (Example) P = 75 PSI = 9 lbs P = 75 PSI ig. (1) Example 1: If the minimum force of 85 lbf is necessary to keep the workpiece pressed as shown in ig. (1), because this is the extending side, use Graph (1) to determine the load factor of.7 and the operating pressure of 75 PSI. Then, seek the point at which the cylinder force of 85 lbf intersects, and this will result in a bore size of 1.5 inches. ig. (2) = ig. (3) 1 lbs Example 2: To move a load with a 9 lbf weight horizontally on a guide as shown in ig. (2), because the load is the same for both the pushing and retracting sides, use Graph (2), which is the retracting side with a smaller force. Determine the load factor of 1, and the operating pressure of 75 PSI. Then, seek the point at which it intersects with the load weight of 9 lbs, and this will result in a bore size of 1.5 inches. Example 3: To pull a load with a 1 lbs weight vertically upward as shown in ig. (3), use Graph (2) to determine the load factor of.5 and the operating pressure of 75 PSI. Then, seek the point at which it intersects with the load weight of 1 lbs, and this will result in a bore size of 2. inches. ront matter 2

5 Model Selection Step 2 Take the impact at the stroke end into consideration. ith umper ithout umper CM Graph (3) llowable inetic Energy with umper 1. Graph (4) llowable inetic Energy without umper CM2 1. CM2 CM15 CM15 CM125 CM125 CM16 CM16 CM88 CM88 1. CM75 1. CM75 CM56 CM56 oad (lb) CM44 oad (lb) CM Max. speed (in/s) Max. speed (in/s) ront matter 3

6 Model Selection Step 3 The aspects indicated below may need to be taken into consideration, depending on how the cylinder is operated. The maximum stroke at which the cylinder can be operated under a lateral load. The region that does not exceed the bold solid line represents the allowable lateral load in relation to the cylinder of a given stroke length. In the graph, the range of the broken line shows that the long stroke limit has been exceeded. In this region, as a rule, operate the cylinder by providing a guide along the direction of movement. Graph (5) Max. llowable ateral oad.44 (7/16"),.56 (9/16"), (3/4"), (7/8"), 1.6 (1-1/16"), 1.25 (1-1/4"), 1.5 (1-1/2"), 2. (2") 1. fr ushing (earing) 1. CM ateral load applied to the rod end fr (lbf) 1. CM56 CME CMC CM2 CM15 CM125 CM16 CM88 CM75.1 CM Cylinder stroke (in) ront matter 4

7 Model Selection Step 3 The aspects indicated below may need to be taken into consideration, depending on how the cylinder is operated. Mounting Mounting Type Type 1 Type 2 Type 3 Type 1 Type 1 Type 4 Type 2 Type 3 Type 2 Type 3 Type perating pressure (PSI) (12) , (12) U T , , Maximum stroke that can be used according to buckling strength CM The relationship between the cylinder size and the maximum stroke depending on the mounting style. ssuming that the force that is generated by the cylinder itself acts as a buckling force on the piston rod or on the piston rod and the cylinder tube, the table below indicates in inches the maximum stroke that can be used, which was obtained through calculation. Therefore, it is possible to find the maximum stroke that can be used with each cylinder size according to the relationship between the level of the operating pressure and the type of cylinder mounting, regardless of the load factor. Reference: Even under a light load, if the piston rod has been stopped by an external stopper at the extending side of the cylinder, the maximum force generated by the cylinder will act upon the cylinder itself. The data in ( ) are limited by max. stroke length. ote 1) This data is in.5 inch increments (round off). ote 2) or those that exceed maximum stroke that can be manufactured, (4) indicates the maximum stroke that can be manufactured (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) 11 (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (12) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) (4) P ront matter 5

8 Model Selection Step 4 btain the cylinder s air consumption and its required air volume. Cylinder s air consumption and its required air volume. In equipment that used a cylinder, air consumption is the volume of air that is consumed in the cylinder, or in the piping between the cylinder and the switching valve, every time the switching valve operates. This is necessary for selecting a compressor and for calculating the running cost. The required air volume is the volume of air that is necessry for operating a specified load at a specified speed, and it is necessary for selecting the.r. equipment or the size of the upstream piping. How to btain the ir Consumption/How to Read Graphs (6), (7) Step 1 Step 2 Step 3 ote)in selecting a compressor, the temperature drop, leakage, and consumption by the intermediary equipment must be taken into consideration. Thus, select one with a generous capacity, with a discharge that exceeds the total air consumption indicated above. (Reference: t a minimum, select one with 1.4 times the volume; select one with a higher volume as needed.) Example: hen 1 air cylinders with a 1.25 inch bore size and a 3 inch stroke are used at a pressure of 5 PSI, what is the air consumption of their 5 cycles per minute? ( 2 inch tube with a.179 inch bore is used for piping between the cylinders and the switching valve.) 1.perating pressure 5 PSI Cylinder stroke 3 inch ore size 1.25 inch ir consumption.5 l(r) 2.perating pressure 5 PSI Piping length 2 inch ore.179 inch ir consumption.1 l (R) 3.Total air consumption = (.5 +.1) x 1 x 5 = 3 l/min (R) How to btain the Required ir Volume/How to Read Graph (8) Step 3 y using Graph (6), obtain the air consumption of the air cylinder. Seek the point at which the operating pressure (diagonal line) intersects with the cylinder stroke, and from that point, perpendicularly extend a vertical line upward. rom the point at which it intersects with the bore size (diagonal line) of the cylinder to be used, look sideways (Either to the right or left) to obtain the air consumption that is required by one cycle of the air cylinder. y using Graph (7), obtain the air consumption of the tube or steel pipe in the same way as in Step 1. btain the total air consumption per minute as described below. (ir consumption of air cylinder + ir consumption of tube or steel pipe) x umber of cycles per minute x umber of cylinders being used = Total air consumption [Unit: l/min (R)] y using Graph (8), obtain the air cylinder s required air volume. Seek the point at which the operating pressure (diagonal line) intersects with the cylinder stroke, and from that point, perpendicularly extend a vertical line upward. rom the point at which it intersects with the bore size (diagonal line) of the cylinder to be used, look sideways (Either to the right or left) to obtain the air consumption that is required by one cycle of the air cylinder. Example:hat is the required air volume for operating a cylinder with a bore size of 1.25 inch, at pressure of 5 PSI, and at a speed of 1 inch/s? How to read: perating pressure 5 PSI Maximum piston speed 5 mm/s ore size 1.25 inch Then, a required air volume 3 l/min (R) can be obtained. Graph (6) Cylinder s ir Consumption (or one cycle) ir consumption (l (R)) Cylinder stroke (in) perating pressure (PSI) ore size (in) ir consumption (l(r)).1 ront matter 6

9 Model Selection Step 4 btain the cylinder s air consumption and its required air volume. Cylinder s air consumption and its required air volume. In equipment that used a cylinder, air consumption is the volume of air that is consumed in the cylinder, or in the piping between the cylinder and the switching valve, every time the switching valve operates. This is necessary for selecting a compressor and for calculating the running cost. The required air volume is the volume of air that is necessry for operating a specified load at a specified speed, and it is necessary for selecting the.r. equipment or the size of the upstream piping. Graph (7) ir Consumption of Tube or Steel Pipe (or one cycle) Graph (8) Required ir Volume of Cylinder and Piping ir consumption (l (R)) Tube I.D. (in) ir consumption (l (R)).1.1 Required air volume (l /min (R)) ore size (in) Required air volume (l /min (R)) Piping length perating pressure (PSI) Max. piston speed (inch/s) perating pressure (PSI) The piping length is the length of the steel pipe or tube that connects the cylinder with the switching valve (solenoid valve, etc.) or the dimensions (bore size and.d.) of the steel tubing, refer to SMC est Pneumatics 24 Vol. 6 catalog. ront matter 7

10 ir Cylinder: Standard Double cting, Single/Double Rod Series CM How to rder C M M9 uilt-in magnet il D one uilt-in magnet with auto switch Mounting C E R ront nose mount Rear pivot mount Double end mount lock mount ote 2, 1, 11) Double rod ote 3, 1) ore size /16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 2" ote 3, 4) Standard stroke Inches ote 5) Stroke Hundredths of an inch (i.e. 6 =.6") il ithout C ote 6) umper bumper umper il J ote 1, 11) Rod boot one ylon tarpaulin Heat resistant tarpaulin ote 1) ption hen ordering multiple options, refer to options compatibility page to ensure options availability. il one X6 High temperature ote 1, 11) X7 ow temperature ote 1, 11) X9 ow speed ote 1, 11) XC4 Heavy duty wiper ote 1) XC6 Stainless steel rod ote 9) X13US Rotated ports ote 7, 1) X114US Rear clevis mount without pin and with rear clevis bronze bushing. ote 1, 11) X142US ong stroke ote 1,11) X155US Rear pivot mount (C) without clevis pin ote 1, 11) X163US Heavy duty spring ote 12) X169US Dimensional interchange to other manufacturer s magnetic reed switch cylinders ote 1, 8, 1) X62 ir tank ote 1) X65 Spring assist ote 12) umber of auto switches il 2 pcs. S 1 pc. n n pcs. uto switch il ithout auto switch or applicable auto switch models, refer to the table on page 2. ote 1) ø3/4", ø1-1/16", ø1-1/2" and ø2" only. ote 2) ot offered in ø7/8", ø1-1/4", or with rod boot. ote 3) Double acting only. ote 4) ot available as standard with C, R mount, with rod boot. ote 5) See specifications for standard and maximum stroke lengths. ote 6) umper is offered at no additional cost on ø7/8" and ø1-1/4". They are options on the other bore sizes. The C after the bore size must be included in either case. umper affects cylinder overall length of some models. Refer to the dimensional data. ote 7) vailable only with or C mounting. ot available on 2" bore. ote 8) ot available with ø7/8" bore, or with C, R mount, or non-rotating rod (). ote 9) Stainless steel rod standard on ø7/16", ø9/16", ø3/4" and ø7/8". ote 1) Exclude ø7/16" and ø9/16". ote 11) Exclude ø2". ote 12) ø3/4", ø1-1/16" and ø1-1/2" only. 1

11 Series CM uto Switch Specifications pplicable uto Switches Type Solid state switch Reed switch Special function Diagnostic indication (2-color indication) ater resistant (2-color indication) ith diagnostic output (2-color indication) Diagnostic indication (2-color indication) Electrical entry Grommet Connector Grommet Grommet Connector Grommet iring (utput) 3-wire (P) 3-wire (PP) 2-wire 3-wire (P) 24 V 5 V, 12 V 3-wire (PP) 2-wire 4-wire (P) ead wire length symbols:.5 m il (Example) M9 1 m M (Example) M9M 3 m (Example) M9 5 m Z (Example) M9Z oad voltage one (Example) H7C or details about auto switches with pre-wired connector, refer to est Pneumatics catalog. D-9, M9, M9 are shipped together. (nly switch mounting bracket is assembled at the time of shipment.) D-M9M and M9VM which lead wire length is 1 m are available from July, 28. Indicator light Yes Yes one Yes one Yes one Yes 3-wire (P equivalent) 2-wire 24 V DC 5 V, 12 V 12 V 12 V 5 V, 12 V 5 V 12 V C 1 V 1 V or less 1 V, 2 V 2 V or less 24 V or less uto switch model M9 M9P M9 H7C M9 M9P M9 H7 H C73C C8C 59 ead wire length (m).5 (il) 1 (M) 3 () Solid state switches marked with are produced upon receipt of order. D-54, 64, and 59 cannot be mounted for bore size 44 and (Z) one () Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC 2

12 Series CM ption Compatibility ption Compatibility (1) Description ote CMStandard CDM CM CM- J CM- C X6 X7 X9 XC6 CM CDM CM CM- J CM- C X6 X7 X9 XC6 C E R Standard uto switch capable Double rod ylon rod boot eoprene rod boot umper Heat resistant Cold resistant ow speed Stainless steel rod ront nose mount Rear pivot mount Double end mount lock mount 5 1, 5 1, 5 2 1, 5 1, 5 1, , 5 Combination available to order S vailable with special request ot available ote 1) Exclude ø2". ote 2) umper no additional charge on ø7/8" and ø1-1/4". ote 3) Stainless steel rod standard on ø7/16", ø9/16", ø3/4" and ø7/8". Use XC6 option to get stainless steel rod nut. ote 4) lock mount not available in ø7/8" and ø1-1/4". ote 5) Exclude ø7/16" and ø9/16". S S S S S S S S S S S S S S S ption Compatibility (2) Double acting, Single rod, o bumper Double acting, Single rod, ith bumper Double acting, Double rod, o bumper Double acting, Double rod, ith bumper ith rod boot Direct double acting, Single rod, o bumper Direct double acting, Single rod, ith bumper Direct single acting, Spring return (S), o bumper Direct single acting, Spring extend (T), o bumper Double acting, Single rod, o bumper X6 Double acting, Single rod, o bumper X7 Double acting, Single rod, o bumper X9 Double acting, Single rod, ith bumper X9 Double acting, Single rod, o bumper XC6 Double acting, Single rod, ith bumper XC6 Double acting, Single rod, o bumper, ith air cushion Standard Standard Standard Standard

13 Series CM Specifications: Double cting, Single/Double Rod Specifications ore size 44 (7/16") 56 (9/16") 88 (7/8") 16 (1-1/16") 2 (2") luid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed umper ubrication Mounting ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C o bumper: 2 to 2 in/sec (5 to 5 mm/sec) umper: 2 to 3 in/sec (5 to 75 mm/sec) ptional (o additional charge on 7/8" and 1-1/4" bore) ot required (Pre-lubricated at factory), C, E, R (see ote) ote) R mount available on ø3/4", ø1-1/16", and ø1-1/2" only. Standard Stroke Mounting ront nose mount () Rear pivot mount (C) Double end mount (E) lock mount (R) ote 3) Double rod () ote 3) Standard stroke 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 Max. stroke as standard ote 2) ong stroke -X142US ote 3) 4 ote 1) Minimum stroke for mounting auto switches:.6 inch for 2 switches,.4 inch for one switch. ote 2) The production maximum stroke of ø7/16" and ø9/16" are up to 12 inches. ote 3) Exclude ø7/16" and ø9/16" eight (Except on-rotating Rod) ore size 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") ase weight by mounting style C / E R / /.21 /.43 / 1.2 / / / dd l weight per inch stroke, C, E, R / / dd l weight for magnet dd l weight for bumper (lbs) Theoretical utput: Double cting Cylinder (Extend) ore size (in) 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") Rod size (in) perating direction UT I UT I UT I UT I UT I UT I UT I UT I Piston area (in 2 ) perating pressure (PSI) (lbf) 4

14 Series CM Construction: Double cting, Single Rod CM44/56 CM44 shown as example Component Parts o Description Rod cover Head cover Cylinder tube Piston Piston Piston rod 7/16", 9/16" umper Rod seal Piston seal Tube gasket ith bumper Material luminum alloy luminum alloy Stainless steel luminum alloy luminum alloy Stainless steel Urethane R R R ote nodized nodized Chromated Chromated CM75 and above 5 Component Parts o Description Rod cover Head cover Cylinder tube Piston 3/4", 7/8" Piston rod 1-1/16", 1-1/4", 1-1/2", 2" ushing ear ring Retaining ring umper Retaining ring Rod seal Piston seal Piston gasket Material luminum alloy luminum alloy Stainless steel luminum alloy Stainless steel Carbon steel Sintered bronze Phenolic resin Spring steel Urethane Spring steel R R R ith bumper ote nodized nodized Chromated Hard chrome plated

15 Series CM Construction: Double cting, Double Rod Component Parts o Description Rod cover Cylinder tube Piston 3/4", 7/8" Piston rod 1-1/16", 1-1/4", 1-1/2", 2" ushing Retaining ring umper Piston seal Piston gasket Rod seal Material luminum alloy Stainless steel luminum alloy Stainless steel Carbon steel Sintered bronze Spring steel Urethane R R R ote Clear anodized Stainless steel 34 Chromated Hard chrome plated 6

16 Series CM Dimensions: Double cting, Single Rod ront nose mount: C(D)M 44 (7/16") MM-DI Y ZC Z+Stroke ZD-U ZD-U -DI E MM-DI Y.37 ZC ore size 44 (7/16") 56 (9/16") E E.52 o.1-32 o.1-32 MM E /16-2 7/16-2 Y.72 ZC.5.6 ZD o.1-32 o.1-32 Z o bumper, o magnet Z ith bumper, o magnet Z o bumper, ith magnet Z ith bumper, ith magnet Y Z + Stroke ZC ZD E C ømm -U-2 -MUTIG UT 56 (9/16") Z+Stroke ZD-U ZD-U -U-2 -MUTIG UT -DI E, 88 (7/8"),,,, 2 (2") -Mounting ut (incl. except 2" bore) D-cross lats -U-2 ø Pilot ZD ore size 88 (7/8") 2 (2") MM /4-28 1/4-28 5/ /16-2 7/16-2 1/ D E C E /4-16 3/ / Y ZC ZD 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/4 PT Z o bumper Z ith bumper

17 Series CM Dimensions: Double cting, Single Rod Rear pivot mount: C(D)MC 44 (7/16") MM-DI Y Z + Stroke + Stroke 2xZD U YC G-DI Pin G -U-2 -U-2 ZC -U-2 -DI Z+Stroke +Stroke Y 56 (9/16") 2xZD U.37 MM-DI YC G-DI ushing -U-2 -U-2 ZC -U-2 -DI ore size 44 (7/16") 56 (9/16") E G G o.1-32 o.1-32 MM /16-2 7/16-2 Y.72 YC.44 ZC ZD.5 o o.1-32 o bumper, o magnet ith bumper, o magnet o bumper, ith magnet ith bumper, ith magnet Z o bumper, o magnet Z ith bumper, o magnet Z o bumper, ith magnet Z ith bumper, ith magnet , 88 (7/8"),,, Z + Stroke ømm -U-2 D-cross lats -U-2 Y ZC ø Pilot + Stroke ZD ZD ZC YC øg øg Pin -U-2 G X155US ore size 88 (7/8") (without clevis pin) øg ore size MM D E 1/ (7/8") 1/ / / / ote) There are no threads on the CMC 15 rear tang ( dim). 3/4-16 G.375 G /4-16 3/4-16 Y YC Z o bumper Z ith bumper

18 Series CM Dimensions: Double cting, Single Rod Double end mount: C(D)ME 44 (7/16") MM-DI Y ZC Z+Stroke +Stroke 2xZD U YC ZC -MUTIG UT G-DI Pin hole -U-2 -MUTIG UT -DI -DI 56 (9/16") MM-DI Y.37 ZC Z+Stroke +Stroke 2xZD U YC ZC -MUTIG UT G-DI ushing -U-2 -MUTIG UT -DI -DI ore size 44 (7/16") (9/16") E G o.1-32 o.1-32 MM /16-2 7/16-2 Y.72, 88 (7/8"),,,, 2 (2") YC.44 ZC ZD.5 o o.1-32 o bumper, ith bumper, o bumper, ith bumper, o magnet o magnet ith magnet ith magnet Z o bumper, o magnet Z ith bumper, o magnet Z o bumper, ith magnet Z ith bumper, ith magnet Y ZC Z + Stroke + Stroke ZD ZD ZC øg Pivot Pin Hole ø Pilot ømm -U-2 D-cross lats -Mounting ut (incl. except 2" bore) ø Pilot YC YC -Mounting ut (incl. except 2" bore) CME 15 9 ore size 88 (7/8") 2 (2") ore size 88 (7/8") 2 (2") o bumper Z MM /4-28 1/4-28 5/ /16-2 7/16-2 1/2-2 ith bumper Z D E G /4-16 3/ / Y YC ZC ZD 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/4 PT

19 Series CM Dimensions: Double cting, Single Rod lock mount: C(D)MR Z + Stroke E 2-DD tap on ø olt circle X C YE T E ømm U-2 E ø Pilot EE PT 2-Drill & C'ore for H caps screw & T UC from bottom EE PT D cross lats ore size MM /4-28 7/16-2 5/ C D.22 DD 1-32 U 1-32 U 1/4-2 UC E E EE 1/8 1/8 1/ E H 1-32 U 1-32 U 1/4-2 UC T 1/4-2 1/4-2 5/16-18 T YE X lock Mount ore size o bumper Z ith bumper ote) ength not affected by addition of magnet. 1

20 Series CM Dimensions: Double cting, Double Rod Z + (2 X Stroke) + Stroke + Stroke YE YE ømm 2-ZD 2-ZC 2-ø Pilot 2- U-2 2-D cross lats 2-Y 2-2- Mounting ut (incl. except 2" bore) ore size 88 (7/8") 2 (2") MM /4-28 1/4-28 5/ /16-2 7/16-2 1/ D E /4-16 3/ / Y YE ZC ZD 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/8 PT 1/4 PT Double cting, Double Rod ore size 88 (7/8") 2 (2") o bumper ith bumper o bumper ith bumper ote) ength not affected by addition of magnet except 16 bore. Z Double cting, Double Rod with Magnet (16 ore) ore size o bumper 3.13 ith bumper 3.25 o bumper 4.38 Z ith bumper

21 12

22 ir Cylinder: on-rotating Rod Double cting, Single Rod Series CM How to rder C M M9 uilt-in magnet il D one uilt-in magnet with auto switch ption il X142US one ong stroke on-rotating rod Mounting C E ront nose mount Rear pivot mount Double end mount ore size /4" 7/8" 1-1/16" 1-1/4" 1-1/2" uto switch il ithout auto switch or applicable auto switch models, refer to the table on page 13. umber of auto switches il 2 pcs. S 1 pc. n n pcs. Standard stroke Inches ote 1) Stroke Hundredths of an inch (i.e. 6 =.6") il C umper ithout bumper umper ote 1) See specifications for standard and maximum stroke lengths. 13

23 Series CM uto Switch Specifications pplicable uto Switches Type Solid state switch Reed switch Special function Diagnostic indication (2-color indication) ater resistant (2-color indication) ith diagnostic output (2-color indication) Diagnostic indication (2-color indication) Electrical entry Grommet Connector Grommet Grommet Connector Grommet Indicator light Yes Yes one Yes one Yes one Yes iring (utput) 3-wire (P) 3-wire (PP) 2-wire 3-wire (P) 24 V 5 V, 12 V 3-wire (PP) 2-wire 4-wire (P) 3-wire (P equivalent) 2-wire 24 V oad voltage DC 5 V, 12 V ead wire length symbols:.5 m il (Example) M9 Solid state switches marked with are produced upon receipt of order. 1 m M (Example) M9M D-54, 64, and 59 cannot be mounted for bore size 44 and m (Example) M9 5 m Z (Example) M9Z one (Example) H7C or details about auto switches with pre-wired connector, refer to est Pneumatics catalog. D-9, M9, M9 are shipped together. (nly switch mounting bracket is assembled at the time of shipment.) D-M9M and M9VM which lead wire length is 1 m are available from July, V 12 V 5 V, 12 V 5 V 12 V C 1 V 1 V or less 1 V, 2 V 2 V or less 24 V or less uto switch model M9 M9P M9 H7C M9 M9P M9 H7 H C73C C8C 59 ead wire length (m).5 (il) 1 (M) 3 () 5 (Z) one () Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC ption Compatibility ption Compatibility (1) Description ote CDM CM CDM CM CM- J CM- C X6 X7 X9 XC6 C E R uto switch capable on-rotating ylon rod boot eoprene rod boot umper Heat resistant Cold resistant ow speed Stainless steel rod ront nose mount Rear pivot mount Double end mount lock mount 1, 7 1, 7 1, 7 2 1, 7 1, 7 1, 7 3, 4 1 1, 5, 6, 7 S S S S S S Combination available to order S vailable with special request ot available ote 1) Exclude ø2". ote 2) umper no additional charge on ø7/8" and ø1-1/4". ote 3) Stainless steel rod standard on ø7/16", ø9/16", ø3/4" and ø7/8". Use XC6 option to get stainless steel rod nut. ote 4) on-rotating rod is stainless steel. Use XC6 option to get stainless steel rod nut. ote 5) lock mount not available in ø7/8" and ø1-1/4". ote 6) lock, uto switch capable, S and T only available as special. ote 7) Exclude ø7/16" and ø9/16". ption Compatibility (2) Double acting, Single rod, o bumper, on-rotating rod Double acting, Single rod, ith bumper, on-rotating rod

24 Series CM Specifications: Double cting, Single Rod on-rotating Rod Specifications ore size luid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Rod material umper on-rotating accuracy Maximum allowable torque 88 (7/8") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C 2 to 2 in/sec / 5 to 5 mm/sec Stainless steel 33 ptional (o additional charge on 7/8" and 1-1/4" bore) ± 2. ± ft bf (.6 m).9 ft bf (.13 m).12 ft bf (.16 m) Standard Stroke Mounting Standard stroke Max. stroke as standard ong stroke -X142US ront nose mount () Double end mount (E) Rear pivot mount (C) 1/2, 1, 2, 3, 4, 5, 6, 1/2, 1, 2, 3, 4, 5, 6, 7, 8, 1, 12 ote 1) Minimum stroke for mounting auto switches:.6 inch for 2 switches,.4 inch for one switch. ote 2) Spring return up to 18" available as special request Theoretical utput: on-rotating Rod ore size 88 (7/8") Rod diameter perating direction UT I UT I UT I UT I UT I Effective area (sq.inch) perating pressure (PSI) (lbf) eight (lbs) ore size 88 (7/8") ase weight by mounting style C E dd l weight per inch stroke dd l weight for magnet dd l weight for bumper

25 Series CM Dimensions: Double cting, Single Rod on-rotating Rod ront nose mount Z1 + STRE.9 D C -U-2 1/8 PT E 1/8 PT MUTIG UT (ICUDED) Z2 + STRE.9 øg PI G D -U-2 1/8 PT YC -U-2 -U-2 + STRE Z3 + STRE.9 C-Pilot.87 øg PIVT PI HE (no.pin hole for 1.5" ore) D -DI Pilot Rear pivot mount Double end mount Pilot -DI Pilot Y -U-2 1/8 PT YC -MUTIG UT (ICUDED) + STRE MUTIG UT (ICUDED) ore size 88 (7/8") MM /4-28 1/4-28 5/ /8-24 3/ C D E /4-16 (C) 3/4-16(E) G G.375 G (C) C E /4-16 7/ Y YC.78.78(C) on-rotating Rod (/C/E) Mount ore size 88 (7/8") o bumper (C) ith bumper (C) Z1 o bumper ith bumper ote) ength not affected by addition of magnet. o bumper (C) Z2 ith bumper (C) Z3 o bumper ith bumper

26 ir Cylinder: Standard Single cting, Spring Return/Extend Series CM How to rder C M M9 il D Mounting C E uilt-in magnet one uilt-in magnet with auto switch ront nose mount Rear pivot mount Double end mount ore size /4" 7/8" 1-1/16" 1-1/4" 1-1/2" ption hen ordering multiple options, refer to options compatibility page to ensure options availability. il one Stainless steel rod ote 3) XC6 X65 X163US Spring assist ote 4) Heavy duty spring ote 4) umber of auto switches il 2 pcs. S 1 pc. n n pcs. Standard stroke Inches ote 1) Stroke Hundredths of an inch (i.e. 6 =.6") il ithout C ote 2) umper bumper umper ction S T uto switch il ithout auto switch or applicable auto switch models, refer to the table on page 18. Spring return Spring extend ote 1) See specifications for standard and maximum stroke lengths. ote 2) umper is offered at no additional cost on ø7/8" and ø1-1/4". They are options on the other bore sizes. The C after the bore size must be included in either case. umper affects cylinder overall length of some models. Refer to the dimensional data. ote 3) Stainless steel rod standard on ø3/4" and ø7/8". ote 4) ø3/4", ø1-1/16" and ø1-1/2" only. 17

27 Series CM uto Switch Specifications pplicable uto Switches Type Solid state switch Reed switch Special function Diagnostic indication (2-color indication) ater resistant (2-color indication) ith diagnostic output (2-color indication) Diagnostic indication (2-color indication) Electrical entry Grommet Connector Grommet Grommet Connector Grommet Indicator light Yes Yes one Yes one Yes one Yes iring (utput) 3-wire (P) 3-wire (PP) 2-wire 3-wire (P) 24 V 5 V, 12 V 3-wire (PP) 2-wire 4-wire (P) 3-wire (P equivalent) 2-wire 24 V oad voltage DC 5 V, 12 V ead wire length symbols:.5 m il (Example) M9 Solid state switches marked with are produced upon receipt of order. 1 m M (Example) M9M D-54, 64, and 59 cannot be mounted for bore size 44 and m (Example) M9 5 m Z (Example) M9Z one (Example) H7C or details about auto switches with pre-wired connector, refer to est Pneumatics catalog. D-9, M9, M9 are shipped together. (nly switch mounting bracket is assembled at the time of shipment.) D-M9M and M9VM which lead wire length is 1 m are available from July, V 12 V 5 V, 12 V 5 V 12 V C 1 V 1 V or less 1 V, 2 V 2 V or less 24 V or less uto switch model M9 M9P M9 H7C M9 M9P M9 H7 H C73C C8C 59 ead wire length (m).5 (il) 1 (M) 3 () 5 (Z) one () Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC ption Compatibility ption Compatibility (1) Description ote CDM S T CDM S T C X6 X7 X9 XC6 C E R uto switch capable Spring return Spring extend umper Heat resistant Cold resistant ow speed Stainless steel rod ront nose mount Rear pivot mount Double end mount lock mount ption Compatibility (2) 1, 6 1, 6 1, 6 1, 2, 6 1, 6 1, 6 1, 6 1, 3, 6 1, 6 1, 6 1, 6 1, 5, 6 S S S S Single acting, Spring return (S), o bumper Single acting, Spring return (S), ith bumper Single acting, Spring extend (T), o bumper Single acting, Spring extend (T), ith bumper Direct single acting, Spring return (S), o bumper Direct single acting, Spring extend (T), o bumper Single acting, Spring extend (T), o bumper XC6 Single acting, Spring extend (T), ith bumper XC6 S S S S S Combination available to order S vailable with special request ot available ote 1) Exclude ø2". ote 2) umper no additional charge on ø7/8" and ø1-1/4". ote 3) Stainless steel rod standard on ø7/16", ø9/16", ø3/4" and ø7/8". Use XC6 option to get stainless steel rod nut. ote 4) lock mount not available in ø7/8" and ø1-1/4". ote 5) lock, uto switch capable, S and T only available as special. ote 6) Exclude ø7/16" and ø9/16"

28 Series CM Specifications: Single cting, Spring Return / Spring Extend Specifications ore size 88 (7/8") luid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed umper ubrication Mounting ir 25 PSI / 1.7 MPa 25 PSI /.18 MPa 4 to 14 / 5 to 6 C 2 to 2 in/sec / 5 to 5 mm/s ptional (o additional charge on 7/8" and 1-1/4" bore) ot required (Pre-lubricated at factory), C, E, R ote) R mount available on 3/4", 1-1/16", and 1-1/2" bore only. Standard Stroke Mounting Standard stroke Max. stroke ront nose mount () Rear pivot mount (C) Double end mount (E) lock mount (R) 1/2, 1, 1-1/2, 2, 3, 4 6 ote) Up to 18" available as special request. Theoretical utput: Spring Return (S) with Standard Rod ore size 88 (7/8") Rod diameter perating direction UT I UT I UT I UT I UT I Effective area (sq.inch) ote1) orce on extension (UT) is shown as the theoretical force of a double acting cylinder on extension less the compressed force of the return spring. ote 2) orce on retraction (I) is the resting force of spring when fully retracted Theoretical utput: Spring Extend (T) with Standard Rod ore size 88 (7/8") Rod diameter perating direction UT I UT I UT I UT I UT I Effective area (sq.inch) perating pressure (PSI) ote1) orce on retraction (I) is shown as the theoretical force of a double acting cylinder on retraction less the compressed force of the extend spring. ote 2) orce on extension (UT) is the resting force of spring when fully extended perating pressure (PSI) (lbf) (lbf) 19

29 Series CM Specifications: Single cting, Spring Return / Spring Extend Spring orce: Spring Return (S) and Spring Extend (T) Type Cylinders ore size 88 (7/8") Resting lbf () 3 (13.3) 3 (13.3) 3 (13.3) 7 (31.2) 7 (31.2) Compressed lbf () 6 (26.8) 5.45(24.4) 6 (26.8) 12.4 (55.6) 12.4 (55.6) (lbs) eight: Single cting, Spring Return except on-rotating Rod ore size 88 (7/8") ase weight by mounting style C E st inch of stroke dd l weight per inch stroke R, C, E, C, E, R.224 /.43 / dd l weight for magnet dd l weight for bumper (lbs) eight: Single cting, Spring Extend except on-rotating Rod ore size 88 (7/8") ase weight by mounting style C E st inch of stroke dd l weight per inch stroke R, C, E, C, E, R.21 /.43 / dd l weight for magnet dd l weight for bumper (lbs) 2

30 Series CM Construction: Single cting, Spring Return ith bumper Component Parts o Description Rod cover Head cover Cylinder tube Piston 3/4", 7/8" Piston rod 1-1/16", 1-1/4", 1-1/2" ushing umper Piston seal Piston gasket Spring Spring guide Material luminum alloy luminum alloy Stainless steel luminum alloy Stainless steel Carbon steel Sintered ronze Urethane R R Music wire luminum alloy ote Clear anodized Clear anodized Stainless steel 34 Chromated Hard chrome plated Chromated Chromated 21

31 Series CM Construction: Single cting, Spring Extend ith bumper Component Parts o Description Rod cover Head cover Cylinder tube Piston 3/4", 7/8" Piston rod 1-1/16", 1-1/4", 1-1/2" ushing Retaining ring umper Retaining ring Piston seal Piston gasket Rod seal Spring Spring guide Material luminum alloy luminum alloy Stainless steel luminum alloy Stainless steel Carbon steel Sintered ronze Spring steel Urethane Spring steel R R R Music wire luminum alloy ote Clear anodized Clear anodized Stainless steel 34 Chromated Hard chrome plated Chromated Chromated 22

32 Series CM Dimensions: Single cting, Spring Return ront nose mount / Spring return CM_-_S Z1 + ZC Per 1" of Stroke.9 E C ømm -U-2 D-cross lats -Mounting ut (included) ø Pilot 1/8 PT Double end mount / Spring return CME_-_S Rear pivot mount / Spring return CMC_-_S ømm Y ZC Z + Stroke + Stroke ZD ZD ZC øg Pivot Pin Hole ømm Y ZC Z + Stroke + Stroke ZD ZD ZC øg øg Pin G ø Pilot ore size 88 (7/8") -Mounting ut (incl. except 2" bore) D-cross lats -U-2 MM /4-28 1/4-28 5/ /16-2 7/16-2 ø Pilot YC -Mounting ut (incl. except 2" bore) D E /4-16 3/4-16 G G.375 G 1. ote 1) dimension for CME15 not applicable. There are no flats on the E type 15 bore rear tang. ote 2) dimension for CMC 15 is not applicable. There are no threads on the C type 15 bore rear tang. YC CME 15 ø Pilot -U-2 D-cross lats -U C E YC -U-2 1/2-2 3/4-16 3/ YC ZC Single cting, Spring Return (/C/E) Mount without Magnet ore size 88 (7/8") o bumper ith bumper o bumper ote) dimension for CME15 not applicable. Z1 ith bumper o bumper Z2 ith bumper X155US (without clevis pin) ore size 88 (7/8") øg Single cting, Spring Return (/C) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper Z1 ith bumper o bumper Z2 ith bumper Single cting, Spring Return (E) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper Z2 ith bumper

33 Series CM Dimensions: Single cting, Spring Extend ront nose mount / Spring extend CM_-_T Z1 + ZC Per 1" of Stroke + Stroke.9 YD ømm Double end mount / Spring extend CME_-_T Z2 + ZC Per 1" of Stroke + ZC Per 1" of Stroke + Stroke.9 ømm YD -U-2 D-cross lats -Mounting ut øg Pivot Pin Hole.9 ø Pilot 1/8 PT CM 15 Rear pivot mount / Spring extend CMC_-_T Z2 + ZC Per 1" of Stroke + ZC Per 1" of Stroke + Stroke YD.9 ømm 1.25 øg Pin G -U-2 D-cross lats 2--Mounting ut (included) ore size 88 (7/8") 2-ø Pilot MM /4-28 1/4-28 5/ /16-2 7/16-2 1/8 PT D E /4-16 G G.375 G ote 1) dimension for CME15 not applicable. There are no flats on the E type 15 bore rear tang. ote 2) dimension for CMC 15 is not applicable. There are no threads on the C type 15 bore rear tang..91 CME 15 -U-2 D-cross lats -U-2 ø Pilot /8 PT -U /4-16 3/4-16 YD ZC Single cting, Spring Extend (/C/E) Mount without Magnet ore size 88 (7/8") o bumper ith bumper o bumper ote) dimension for CME15 not applicable. Z1 ith bumper o bumper Z2 ith bumper X155US (without clevis pin) ore size 88 (7/8") øg Single cting, Spring Extend (/C) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper Z1 ith bumper o bumper Z2 ith bumper Single cting, Spring Extend (E) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper ote) dimension for CME15 not applicable. Z2 ith bumper

34 ir Cylinder: on-rotating Rod Single cting, Spring Return Series CM How to rder C M M9 uilt-in magnet il D one uilt-in magnet with auto switch on-rotating rod ption hen ordering multiple options, refer to options compatibility page to ensure options availability. il one X163US Heavy duty spring Mounting C E ront nose mount Rear pivot mount Double end mount ore size /4" 7/8" 1-1/16" 1-1/4" 1-1/2" umber of auto switches il 2 pcs. S 1 pc. n n pcs. Standard stroke Inches ote 2) Stroke Hundredths of an inch (i.e. 6 =.6") il ithout C ote 3) umper bumper umper ction S Spring return uto switch il ithout auto switch or applicable auto switch models, refer to the table on page 28. ote 1) ot available with double rod (), block mount (R), rod boot. ote 2) See specifications for standard and maximum stroke lengths. ote 3) umper is offered at no additional cost on ø7/8" and ø1-1/4". They are options on the other bore sizes. The C after the bore size must be included in either case. umper affects cylinder overall length of some models. Refer to the dimensional data. 25

35 Series CM uto Switch Specifications pplicable uto Switches Type Solid state switch Reed switch Special function Diagnostic indication (2-color indication) ater resistant (2-color indication) ith diagnostic output (2-color indication) Diagnostic indication (2-color indication) Electrical entry Grommet Connector Grommet Grommet Connector Grommet Indicator light Yes Yes one Yes one Yes one Yes iring (utput) 3-wire (P) 3-wire (PP) 2-wire 3-wire (P) 24 V 5 V, 12 V 3-wire (PP) 2-wire 4-wire (P) 3-wire (P equivalent) 2-wire 24 V oad voltage DC 5 V, 12 V ead wire length symbols:.5 m il (Example) M9 Solid state switches marked with are produced upon receipt of order. 1 m M (Example) M9M D-54, 64, and 59 cannot be mounted for bore size 44 and m (Example) M9 5 m Z (Example) M9Z one (Example) H7C or details about auto switches with pre-wired connector, refer to est Pneumatics catalog. D-9, M9, M9 are shipped together. (nly switch mounting bracket is assembled at the time of shipment.) D-M9M and M9VM which lead wire length is 1 m are available from July, V 12 V 5 V, 12 V 5 V 12 V C 1 V 1 V or less 1 V, 2 V 2 V or less 24 V or less uto switch model M9 M9P M9 H7C M9 M9P M9 H7 H C73C C8C 59 ead wire length (m).5 (il) 1 (M) 3 () 5 (Z) one () Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC ption Compatibility ption Compatibility (1) Description ote CM-S CM-T C CM-S CM-T C C E Spring return Spring extend umper ront nose mount Rear pivot mount Double end mount 1, 3 1, 3 1, 2, 3 1, 3 1, 3 1, 3 Combination available to order S vailable with special request ot available ote 1) Exclude ø2". ote 2) umper no additional charge on ø7/8" and ø1-1/4". ote 3) Exclude ø7/16" and ø9/16". ption Compatibility (2) Single acting, Spring return (S), on-rotating rod, o bumper Single acting, Spring return (S), on-rotating rod, ith bumper

36 Series CM Specifications: Single cting, Spring Return on-rotating Rod Specifications ore size luid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Rod material umper on-rotating accuracy Maximum allowable torque 88 (7/8") ir 25 PSI / 1.7 MPa 25 PSI /.18 MPa 4 to 14 / 5 to 6 C 2 to 2 in/sec / 5 to 5 mm/s Stainless steel 33 ptional (o additional charge on 7/8" and 1-1/4" bore) ± 2. ± ft bf (.6 m).9 ft bf (.13 m).12 ft bf (.16 m) Standard Stroke Mounting Standard stroke Max. stroke ront nose mount () Double end mount (E) Rear pivot mount (C) 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 1/2, 1, 2, 3, 4, 5, 6 ote 1) Minimum stroke for mounting auto switches:.6 inch for 2 switches,.4 inch for one switch. ote 2) Spring return up to 18" available as special request. Theoretical utput ore size 88 (7/8") Rod diameter perating direction UT I UT I UT I UT I UT I 6 6 Effective area (sq.inch) ote1) orce on extension (UT) is shown as the theoretical force of a double acting non-rotating rod cylinder on extension less the compressed force of the return spring. ote 2) orce on retraction (I) is the resting force of spring when fully retracted perating pressure (PSI) (lbf) eight ore size 88 (7/8") ase weight by mounting style C st Inch of stroke dd l weight per inch stroke E, C, E, C, E dd l weight for magnet dd l weight for bumper (lbs) 27

37 Series CM Dimensions: Single cting, Spring Return on-rotating Rod ront nose mount / Spring return CM_-_S Z1 + ZC per 1" of Stroke.9 D C -U-2 Mounting ut (included) ø Pilot E 1/8 PT Double end mount / Spring return CME_-_S Rear pivot mount / Spring return CMC_-_S.9 Z2 + ZC per 1" of Stroke + ZC per 1" of Stroke ø Pilot.9 øg PIVT PI HE Z2 + ZC per 1" of Stroke + ZC per 1" of Stroke.9 øg PI G D D -U-2 MUTIG UT (included) ø Pilot 1/8 PT YC MUTIG UT (included) -U-2 -U-2 ø Pilot 1/8 PT YC -U-2 ore size 88 (7/8") 1/4-28 1/4-28 5/ /16-2 7/ C D E /4-16 3/4-16 G G.375 ote 1) dimension for CME15 not applicable. There are no flats on the E type 15 bore rear tang. ote 2) dimension for CMC 15 is not applicable. There are no threads on the C type 15 bore rear tang. G C E /2-2 3/4-16 3/ YC ZC Single cting, Spring Return (/C/E) Mount without Magnet ore size 88 (7/8") o bumper ith bumper o bumper Z ote) dimension for CME15 not applicable. ith bumper o bumper Z2 ith bumper X155US (without clevis pin) ore size 88 (7/8") øg Single cting, Spring Return (/C) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper Z1 ith bumper o bumper Z2 ith bumper Single cting, Spring Return (E) Mount with Magnet ore size 88 (7/8") o bumper ith bumper o bumper Z2 ith bumper

38 Series CM High Temperature -X6 ption Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ction uto switch capable 88 (7/8") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 3 / 2 to 15 C 2 to 2 in/sec / 5 to 5 mm/s ot available Double acting Special order only High temperature up to 3 Double acting only Standard Stroke Mounting ront nose () Rear pivot, Double end (C, E) Standard stroke 1/2, 1, 1-1/2, 2, 3, 4, 5, 6 1/2, 1, 1-1/2, 2, 3, 4, 5, 6, 8, 1, 12 Max. stroke 6 12 How to rder CM Mounting ore Stroke ption X6 Ex.) CM 75-4-X6 High temperature ow Temperature -X7 ption Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ction uto switch capable 88 (7/8") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 22 to 158 / 3 to 7 C 2 to 2 in/sec / 5 to 5 mm/s ot available Double acting Special order only ow temperature down to 22 Double acting only Standard Stroke Mounting ront nose () Rear pivot, Double end (C, E) Standard stroke 1/2, 1, 1-1/2, 2, 3, 4, 5, 6 1/2, 1, 1-1/2, 2, 3, 4, 5, 6, 8, 1, 12 Max. stroke 6 12 How to rder CM Mounting ore Stroke ption X7 Ex.) CM 75-4-X7 ow temperature 29

39 Series CM Heavy Duty iper -XC4 ption Rod wiper option Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ubrication uto switch capable Mounting Standard Stroke Mounting ront nose () Rear pivot (C) Double end mount (E) 88 (7/8") 2 (2") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C o bumper: 2 to 2 in/sec (5 to 5 mm/sec) umper: 2 to 3 in/sec (5 to 75 mm/sec) ptional ot required (Pre-lubricated at factory) ptional, C, E Standard stroke 1/2, 1, 2, 3, 4, 5, 6 How to rder Max. stroke C(D)M Mounting ore Stroke ption XC4 Ex.) CDME75-4-M9-XC4 3

40 Series CM Stainless Steel Rod -XC6 ption Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ction uto switch capable 88 (7/8") 2 (2") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C 2 to 2 in/sec / 5 to 5 mm/s ptional (o additional charge on 1-1/4" bore) Double acting ptional Stainless steel piston rod is used to protect in harsh or wet environments. uto switch capable Stainless steel rod is a standard on bores 3/4 and 7/8 and nonrotating rod. dd -XC6 to obtain stainless steel rod nut. Standard Stroke Mounting Standard stroke ront nose () 1/2, 1, 1-1/2, 2, 3, 4, 5, 6 Rear pivot, Double end (C, E) 1/2, 1, 1-1/2, 2, 3, 4, 5, 6, 8, 1, 12 ote) See standard specifications for minimum and maximum strokes. C(D)M How to rder Mounting ore Stroke ption XC6 Ex.) CDM 15-4-XC6 Max. stroke 6 12 Stainless steel rod ow Speed -X9 ption Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ction uto switch capable 88 (7/8") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C.4 to 2 in/sec / 1 to 5 mm/s ptional (o additional charge on 7/8" and 1-1/4" bore) Double acting ptional Smooth movements even at.4 to 2. inch/sec. Double acting uto switch capable Standard Stroke Mounting Standard stroke ront nose () 1/2, 1, 1-1/2, 2, 3, 4, 5, 6 Rear pivot, Double end (C, E) 1/2, 1, 1-1/2, 2, 3, 4, 5, 6, 8, 1, 12 ote) See standard specifications for minimum and maximum strokes. How to rder Max. stroke 6 12 CM Mounting ore Stroke ption X9 Ex.) CDM 75-4-X9 ow speed 31

41 Series CM Rod oot ption Rod oot Material Mounting J * Max. temperature is for boot only. Material Tarpaulin Heat resistant tarpoulin Max. temperature 14 (6 C) *23 (11 C) Maximum Stroke ore size 3/4, 7/8, 1-1/16 1-1/4, 1-1/2, 2 Max. stroke 12 Standard - 16 Maximum 12 Standard - 26 Maximum oots are supplied to protect the surface of piston rod and rod seals in harsh or wet environments. ore size 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2" Double acting only CM How to rder Mounting ore Stroke ption J Ex.) CDM 75-4 J Rod boot J - Tarpaulin - Heat resistant tarpaulin pprox..28 inch (all bores) ore size E to to to to to to to to to to (7/8") to ore size to to to to to to to to to to to (7/8")

42 Series CM Rotated Rear Port -X13US ption Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ubrication uto switch capable Mounting 88 (7/8") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C o bumper: 2 to 2 in/sec (5 to 5 mm/sec) umper: 2 to 3 in/sec (5 to 75 mm/sec) ptional ot required (Pre-lubricated at factory) ptional, C Standard Stroke Mounting ront nose () Rear pivot (C) Standard stroke 1/2, 1, 2, 3, 4, 5, 6 How to rder Max. stroke C(D)M Mounting ore Stroke ption X13US Ex.) CDM75-4-M9-X13US 33

43 Series CM Rotated Rear Port -X13US ption C(D)M ore - Stroke -X13US Z + STRE Y 1/8 PT 1/8 PT.9 ø PIT YC ømm ø U-2 D CRSS TS CRSS TS MUTIG UT ithout umper ore size 88 (7/8") MM /4-28 1/4-28 5/ /16-2 7/ D E /4-16 3/ Y YC Z ith umper ore size 88 (7/8") Z C(D)MC ore - Stroke -X13US Y Z + STRE 1/8 PT 1/8 PT.9 ø PIT ø PIT YC G øg Pin Dia ømm U-2 CRSS TS.9 U-2 D CRSS TS -U-2 STDRD PRT ocation (Plugged) (pposite side shown) + STRE ithout umper ore size 88 (7/8") MM /4-28 1/4-28 5/ /16-2 7/ D E /4-16 G.375 G /4-16 3/ Y YC Z ith umper ore size 88 (7/8") Z

44 Series CM Rotated Rear Port -X13US ption C(D)M ore - Stroke -X13US Y Z + STRE 1/8 PT 1/8 PT D.9 ø PIT YC YC ø ø ømm U-2 CRSS TS MUTIG UT CM15 ithout umper ore size 88 (7/8") MM /4-28 1/4-28 5/ /8-24 3/ D E /4-16 7/ Y YC Z ith umper ore size 88 (7/8") Z C(D)MC ore - Stroke -X13US Z + STRE Y 1/8 PT 1/8 PT D.9 ø PIT ø PIT YC G ømm øg U-2 CRSS TS.9 U-2 U-2 STDRD PRT CTI (PUGGED) (PPSITE SIDE SH) + STRE ithout umper ore size 88 (7/8") MM /4-28 1/4-28 5/ /8-24 3/ D E /4-16 G.375 G /4-16 7/ Y YC Z ith umper ore size 88 (7/8") Z

45 Series CM Rear Clevis Mount without Pin and with Rear Clevis ronze ushing -X114US ption ronze bushing in place of clevis pin Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ubrication uto switch capable Mounting Standard Stroke 88 (7/8") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C o bumper: 2 to 2 in/sec (5 to 5 mm/sec) umper: 2 to 3 in/sec (5 to 75 mm/sec) ptional ot required (Pre-lubricated at factory) ptional E Mounting Standard stroke Double end mount (E) 1/2, 1, 2, 3, 4, 5, 6 Max. stroke 32 How to rder C(D)M Mounting ore Stroke ption X114US Ex.) CDME75-4-M9-X114US C(D)ME(75 to 5)- Stroke (C)-X114US øg PIVT PI HE RZE USHIG ith umper ore size 88 (7/8") G

46 Series CM Rear Pivot Mount without Clevis Pin -X155US ption Rear clevis mount without rear clevis pin Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ubrication uto switch capable Mounting Standard Stroke 88 (7/8") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C o bumper: 2 to 2 in/sec (5 to 5 mm/sec) umper: 2 to 3 in/sec (5 to 75 mm/sec) ptional ot required (Pre-lubricated at factory) ptional C Mounting Standard stroke Rear pivot (C) 1/2, 1, 2, 3, 4, 5, 6 Max. stroke 38 How to rder C(D)M Mounting ore Stroke ption X155US Ex.) CDMC75-4-M9-X155US Single cting with Heavy Spring orce -X163US ption Single acting with heavy spring force Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ubrication uto switch capable Mounting ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C o bumper: 2 to 2 in/sec (5 to 5 mm/sec) umper: 2 to 3 in/sec (5 to 75 mm/sec) ptional ot required (Pre-lubricated at factory) ot vailable, C, E Spring orce: Spring Return (S) and Spring Extend (T) Type Cylinders ore size Resting lbs () 2 (8.9) 5.5 (24.5) 7.5 (33.4) Compressed lbs () 9 (4) 11.5 (51.1) 16 (71.1) Standard Stroke Mounting ront nose () Rear pivot (C) Double end mount (E) Standard stroke 1/2, 1, 2, 3, 4, 5, 6 How to rder Max. stroke 6 CM Mounting ore Stroke ption X163US Ex.) CM75-4-X163US 37

47 Series CM Dimensional Interchange to ther Manufacturers Magnetic Reed Switch Cylinders -X169US ption Interchange with other manufacturers MRS cylinder Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ubrication uto switch capable Mounting Standard Stroke Mounting ront nose () Double end mount (E) Double rod () 2 (2") ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C o bumper: 2 to 2 in/sec (5 to 5 mm/sec) umper: 2 to 3 in/sec (5 to 75 mm/sec) ptional ot required (Pre-lubricated at factory) Standard, E, Standard stroke 1/2, 1, 2, 3, 4, 5, 6 How to rder Max. stroke CDM Mounting ore Stroke ption X169US Ex.) CDM75-4-M9-X169US CDM(75 to 2)- Stroke (C)-X169US Z + STRE -DI. PIT ømm.9 EE PT E C -U-2 D-CRSS TS Y EE PT -MUTIG UT ithout umper ore size 2 (2") ø D EE 1/8 1/8 1/8 1/4 1/4.31 1/4-28 5/ /8-24 7/16-2 1/2-2 ømm C E /4-16 7/ / Y Z ith umper ore size 2 (2") Z

48 Series CM Dimensional Interchange to ther Manufacturers Magnetic Reed Switch Cylinders -X169US ption CDME(75 to 2)- Stroke (C)-X169US Z + STRE -DI. PIT ømm.9 EE PT EE PT.9 G-DI. PIVT PI HE -U-2 D-CRSS TS Y YC -MUTIG UT + STRE -MUTIG UT ithout umper ore size 2 (2") ø D EE 1/8 1/8 1/8 1/4 1/ øg /4-28 5/ /8-24 7/16-2 1/ ømm /4-16 7/ / Y YC Z ith umper ore size 2 (2") Z CDM(75 to 2)- Stroke (C)-X169US Z + STRE -DI. PIT ømm.9 EE PT + STRE EE PT + STRE.9 ømm -DI. PIT -U-2 D-CRSS TS YE YE -MUTIG UT -U-2 D-CRSS TS -MUTIG UT Y Y + STRE ithout umper ith umper ore size 2 (2") ø D EE 1/8 1/8 1/8 1/4 1/4.31 1/4-28 5/ /8-24 7/16-2 1/ ømm /4-16 7/ / Y YE Z ore size 2 (2") Z

49 Series CM ir Tank -X62 ption Specifications ore size luid Max. operating pressure Mounting 88 (7/8") 2 (2") ir 25 PSI / 1.7 MPa, E Standard ength Mounting ront nose () Double end mount (E) Standard length 1, 2, 3, 4, 5, 6 Max. length 38 ir reservoir Volume Mounting ront nose () Double end mount (E) ore Standard length per inch of length per inch of length.95 + per inch of length per inch of length per inch of length per inch of length per inch of length per inch of length per inch of length per inch of length per inch of length per inch of length (cubic inch) How to rder CM Mounting ore Stroke X62 Ex.) CM75-4-X62 CM(75 to 2)- Stroke -X62 Z + EGTH E E 2-ZD PT C ithout umper ore size 88 (7/8") 2 (2") C E Z ZD 1/8 1/8 1/8 1/8 1/8 1/4 Volume (Cubic inches) per inch of length per inch of length.95 + per inch of length per inch of length per inch of length per inch of length 4

50 Series CM ir Tank -X62 ption CME(75 to 2)- Stroke -X62 Z + EGTH + EGTH ZC 2-ZD PT ZC 2-2- MUTIG UT 2-øG PIVT PI HE ithout umper ore size 88 (7/8") 2 (2") øg /4-16 3/ /4-12 Z ZC ZD 1/8 1/8 1/8 1/8 1/8 1/4 Volume (Cubic inches) per inch of length per inch of length per inch of length per inch of length per inch of length per inch of length 41

51 Series CM Double cting/spring ssist -X65 ption Double acting with spring Specifications ore size luid Max. operating pressure Min. operating pressure mbient and fluid temp. Piston speed umper ubrication uto switch capable Mounting Standard Stroke Mounting ront nose () Rear pivot (C) Double end mount (E) ir 25 PSI / 1.7 MPa 8 PSI /.6 MPa 4 to 14 / 5 to 6 C o bumper: 2 to 2 in/sec (5 to 5 mm/sec) umper: 2 to 3 in/sec (5 to 75 mm/sec) ptional ot required (Pre-lubricated at factory) ptional, C, E Standard stroke 1/2, 1, 2, 3, 4, 5, 6 How to rder Max. stroke 6 C(D)M Mounting ore Stroke ption X65 Ex.) CDM75-4-X65 CM(75 to 15)- Stroke (C)S-X65 Z+ZC PER 1" STRE.5.9 E ø ømm -U-2 YD 2-1/8 PT C D-CRSS TS ithout umper ore size ømm ø ø.312 ø.437 1/4-28 5/ /16-2 ø ø4 ø4 ø.749 D ø.86 ø1.12 ø1.56 ote: or fractions 1/2" go to next highest whole stroke and subtract 1/2" C 1.25 E /4-16 YD Z ZC ith umper ore size Z

52 Series CM Double cting/spring ssist -X65 ption CM(75 to 15)- Stroke (C)T-X65 +STRE.5 Z+ZC PER 1" STRE.9 E ø ømm -U-2 -MUTIG UT YD 2-1/8 PT C D-CRSS TS ithout umper ore size ømm ø ø.312 ø.437 1/4-28 5/ /16-2 ø ø4 ø4 ø.749 D ø.86 ø1.12 ø1.56 ote: or fractions 1/2" go to next highest whole stroke and subtract 1/2" C 1.25 E /4-16 YD Z ZC ith umper ore size Z CMC(75 to 15)- Stroke (C)S-X65 Z+ZC PER 1" STRE.5 2-1/8 PT.9 ø G ømm -U-2 YD YC -U-2 øg PI D-CRSS TS +ZC PER 1" STRE 2--U-2 ithout umper ore size ømm ø ø.312 ø.437 1/4-28 5/ /16-2 ø ø4 ø4 ø.749 D ø.86 ø1.12 ø1.56 ote: or fractions 1/2" go to next highest whole stroke and subtract 1/2". G.375 G /4-16 YD YC.78 Z ZC ith umper ore size Z

53 Series CM Double cting/spring ssist -X65 ption CMC(75 to 15)- Stroke (C)T-X65 Z+ZC PER 1" STRE +STRE.5 2-1/8 PT.9 ø G ømm -U-2 -U-2 YD YC -U-2 øg PI D-CRSS TS +ZC PER 1" STRE ithout umper ore size ømm ø ø.312 ø.437 1/4-28 5/ /16-2 ø ø4 ø4 ø.749 D ø.86 ø1.12 ø1.56 ote: or fractions 1/2" go to next highest whole stroke and subtract 1/2". G.375 G /4-16 YD YC.78 Z ZC ith umper ore size Z CME(75 to 15)- Stroke (C)S-X65 Z+ZC PER 1" STRE.5 2-ø PIT ømm.9 2-1/8 PT.9 øg PIVT PI HE -U-2 YD YC YC D CRSS TS +ZC PER 1" STRE 2- MUTIG UTS CME 15 ithout umper ore size ømm ø ø.312 ø.437 1/4-28 5/ /16-2 ø ø4 ø4 ø.749 D ø.86 ø1.12 ø1.56 ote: or fractions 1/2" go to next highest whole stroke and subtract 1/2". G /4-16 YC.91 YD Z ZC ith umper ore size Z

54 Series CM Double cting/spring ssist -X65 ption CME(75 to 15)- Stroke (C)T-X65 Z+ZC PER 1" STRE +STRE.5 2-ø PIT ømm.9 2-1/8 PT.9 øg PIVT PI HE -U-2 YD YC YC D CRSS TS +ZC PER 1" STRE 2- MUTIG UTS CME 15 ithout umper ore size ømm ø ø.312 ø.437 1/4-28 5/ /16-2 ø ø4 ø4 ø.749 D ø.86 ø1.12 ø1.56 ote: or fractions 1/2" go to next highest whole stroke and subtract 1/2". G /4-16 YD YC.91 Z ZC ith umper ore size Z

55 Series CM ccessories oot bracket J D C G H Part no. pplicable bore size C D E G H J CM-44 CM-75 CM-15 CM-15 CM-2 7/16", 9/16" 3/4", 7/8", 1-1/16" 1-1/4", 1-1/2" 1-1/2" (on-rotating) 2" ote) CM-75 will not fit CM 75 S (Single acting). or this option use: CM ( dimension=.51") Rod clevis D C E øj H G Part no. pplicable bore size C D E G H J Y-44 7/16", 9/16" o o.1-32 Y-75 3/4", 7/8".51 1/ /4-28 Y /16".51 5/ /16-24 Y /4", 1-1/2" 7/ /16-2 Y-G5 2" 1/ /2-2 Jam nut (Rod thread) C D Part no. pplicable bore size JM-2 ote 1) JM-25 JM-3 JM-45 JM-4 JM-5 ote 1) 7/16", 9/16" 3/4", 7/8" 1-1/16" 1-1/4", 1-1/2" 1-1/4", 1-1/2" (on-rotating) 2" ote 1) Please order separately. (44, 56, 2 only) C D o.1-32 U 1/4-28 U 5/16-24 U 7/16-2 U 3/8-24 U 1/2-2 U 46

56 ø Pin Series CM ccessories Pivot bracket (Rear pivot): CMC C D øp J G H E Radius M Part no. pplicable bore size CM-PC44 CM-PC75 CM-PC15 7/16", 9/16" 3/4", 7/8", 1-1/16", 1-1/4" 1-1/2" C D E G H J M øp Pivot bracket (End mount): CME D J G H Part no. pplicable bore size CM-PE56 CM-PE75 CM-PE125 CG-PCø5ø 9/16" 3/4", 7/8" 1-1/16" 1-1/4" 2" C D M.16 G C H Slot J M Mounting nut (ose mount thread) C Part no. pplicable bore size JM-45 JM-8 JM-1 JM-14 7/16", 9/16" 3/4", 7/8" 1-1/16" 1-1/4", 1-1/2" 2" C D 7/16-2 U U 3/4-16 U 1-1/4-12 U D 47

57 Series CM uto Switch Proper Mounting Position and Its Mounting Height (Single rod) D-9(V) = HS D-M9(V)/M9(V) = HS (.98) ( ):D-93 D-C7/C8 HS = HS D-5/6/59 HS D-H7/H7/H7/H7 HS D-C73C/C8C SMC HS D-G5T.63 SMC SMC SMC.63 SMC SMC 1.14 HS In case of CDMC, CDME D-H7C HS

58 Series CM uto Switch Proper Mounting Position and Its Mounting Height (Single rod) uto Switch Mounting Position (CDM) uto switch model ore size 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") Mounting Height (CDM) uto switch model ore size 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") D-M9 D-M D-M9 D-M9 D-9 D-9V HS D D-M9V D-M9V D-H7 D-H7 D-H7 D-H7 D-C7 D-C8 HS D-H7 D-H7 D-H7C D-H7 D-H D-H7C HS D-C7 D-C8 D-C73C D-C8C D-C73C D-C8C HS D-G5T D-G5T D-5 D-59 D-64 HS (in) D-5 D D (in) uto Switch Mounting Position (CDM- * C) uto switch model ore size 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") D-M9 D-M D D-H7 D-H7 D-H7C D-H7 D-H D-C7 D-C8 D-C73C D-C8C D-G5T uto Switch Mounting Position (CDMC, CDME) (in) uto Switch Mounting Position (CDMC- * C, CDME- * C) uto switch model ore size 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") D-M9 D-M D D-H7 D-H7 D-H7C D-H7 D-H D-C7 D-C8 D-C73C D-C8C D-G5T D-5 D D uto switch model ore size 44 (7/16") 56 (9/16") 88 (7/8") 2 (2") ote 1) D-G5T, 5, 64, 59 cannot be mounted on models with bore size 44 and 56. ote 2) hen setting an auto switch, confirm the operation and adjust its mounting position. D-M9 D-M D D-H7 D-H7 D-H7C D-H7 D-H D-C7 D-C8 D-C73C D-C8C D-G5T D-5 D D-5 D (in) D (in) D

59 Series CM uto Switch Proper Mounting Position and Its Mounting Height (Double rod) D-9(V) HS D-M9(V)/M9(V) HS HS D-5/6/59 HS HS SMC SMC SMC SMC (1.42) D-C73C/C8C HS HS SMC SMC (.98) ( ):D-93 D-C7/C8 HS.66 D-H7/H7/H7/H7 D-G5T uto Switch Mounting Position (CDM) uto switch model ore size 88 (7/8") 2 (2") D-M9 D-M D D-H7 D-H7 D-H7C D-H7 D-H D-C7 D-C8 D-C73C D-C8C D-G5T D-5 D uto Switch Mounting Position (CDM- * C) uto switch model ore size 88 (7/8") 2 (2") D-M9 D-M D D-H7 D-H7 D-H7C D-H7 D-H D-C7 D-C8 D-C73C D-C8C D-G5T D-5 D (in) D (in) D D-H7C HS.63 Mounting Height (CDM) uto switch model ore size 88 (7/8") 2 (2") 1.5 D-M9 D-M9 D-9 D-9V HS D-M9V D-M9V D-H7 D-H7 D-H7 D-H7 D-C7 D-C8 HS D-H7C HS D-C73C D-C8C HS D-G5T D-5 D-59 D-64 HS (in) ote 1) D-G5T, 5, 64, 59 cannot be mounted on models with bore size 44 and 56. ote 2) hen setting an auto switch, confirm the operation and adjust its mounting position. 5

60 Series CM uto Switch Proper Mounting Position and Its Mounting Height (lock mount) D-9(V) HS D-M9(V)/M9(V) HS D-C7/C8 HS (.98) ( ):D D-5/6/59 HS D-H7/H7/H7/H7 HS HS D-C73C/C8C HS SMC SMC D-G5T 1.14 (1.42) SMC SMC SMC SMC HS D-H7C uto Switch Mounting Position (CDMR) uto switch model ore size D-M9 D-M D D-H7 D-H7 D-H7C D-H7 D-H D-C7 D-C8 D-C73C D-C8C D-G5T D-5 D uto Switch Mounting Position (CDMR- * C) uto switch model ore size D-M9 D-M D D-H7 D-H7 D-H7C D-H7 D-H D-C7 D-C8 D-C73C D-C8C D-G5T D-5 D (in) D (in) D HS.63 Mounting Height (CDMR and CDMR- * C) uto switch model ore size 88 (7/8") D-M9 D-M9 D-9 D-9V HS D-M9V D-M9V D-H7 D-H7 D-H7 D-H7 D-C7 D-C8 HS D-C73C D-C8C HS (in) D-G5T D-5 D-59 D-64 HS ote 1) D-G5T, 5, 64, 59 cannot be mounted on models with bore size 44 and 56. ote 2) hen setting an auto switch, confirm the operation and adjust its mounting position. 51

61 Series CM Minimum Stroke for uto Switch Mounting (in) uto switch model D-M9 D-M9 D-9 D-M9V D-M9V D-9V umber of switches 2 n n different surfaces n the same surface n different surfaces (n 2) ote 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) n the same surface (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) D-H7 D-H7 D-H7 D-H (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...).4 D-C7 D-C8 D-H7C D-C73C D-C8C D-G5T D-5 D-64 D (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) (n 2) (n = 2, 4, 6...) ote 1) D-G5T, 5, 64, 59 cannot be mounted on models with bore size 44 and 56. ote 2) hen two D-M9, M9, or 93 type auto switches are mounted on models with bore size 44. ith 2 auto switches n different surfaces n the same surface (in) uto switch model D-M9 D-M9 D-93 uto switch D-M9 D-M9 ess than.8" stroke The proper mounting position is.24" inward from the end face of the switch holder. The switches are mounted in staggered positions in a direction (toward the outer circumference of the cylinder tube) in which the switches and lead wires will not interfere with one another. ess than 2" stroke 52

62 Series CM uto Switch Mounting uto Switch Mounting racket Part o. uto switch model ore size D-M9(V) D-M9(V) D-9(V) ote 1) J2-12 J3-1 ote 1) J2-15 J3-1 ote 1) M2-75 J3-1 ote 1) M2-88 J3-1 ote 1) M2-16 J3-1 ote 1) M2-125 J3-1 ote 1) M2-15 J3-1 ote 1) CM-2 J3-1 D-H7 D-H7 D-H7 D-H7 D-C7/8 D-C73C/8C J2-12 J2-15 M2-75 M2-88 M2-88 M2-125 M2-15 CM-2 D-G5T D-5/59/ CM-2 ote 1) Two types of auto switch mounting brackets are used as a set. ote 2) D-G5T, 5, 64, 59 cannot be mounted on models with bore size 44 and 56. e Switch spacer (Stainless steel) d Switch holder (Resin) uto switch Set screw (ot used) c Switch bracket (Stainless steel) b Switch mounting screw Cylinder tubing a Switch mounting band set of the parts marked a and b in the diagram is used for types J2-, M2-, and CM-2. set of the parts marked c, d and e in the diagram is used for type J3-1. Stainless steel screw set The set of stainless steel mounting screws described below is available and can be used depending on the operating environment. s auto switch bracket is not included, order separately. Detailed Contents of Stainless Steel Mounting Screw Sets Part no. 3 4 Description uto switch mounting screw uto switch mounting screw Content Size M4X.7X22 pplicable auto switch mounting bracket part no. D-H7 switch is set on the cylinder with the stainless steel screws (4) above when shipped. hen only a switch is shipped independently, 4 screws are attached. Qty. M3X.5X /88/16/125/15 CM-2 J2-12/15 M2-75/88/16/125/15 CM-2 pplicable auto switch D-G5T D-5 D-64 D-H7 D-C7 D-C8 53

63 Series CM perating Range uto switch model M9(V)/D-M9(V) D-9(V) D-H7/H7/H7/H7 D-H7C D-C7/C8/C73C/C8C D-G5T D-5/64 D ore size ote1) Since this is a guideline including hysteresis, not meant to be guaranteed. (ssuming approximately ±3% dispersion) There may be the case it will vary substantially depending on an ambient environment. ote 2) D-G5T, 5, 64, 59 cannot be mounted on models with bore size 44 and 56. ther than the models listed How to rder, the following auto switches are applicable. uto switch type Model Electrical entry Special function (Entry direction) D-M9V, M9PV, M9V D-H71, H72, H7 Solid state switch D-M9V, M9PV, M9V Diagnostic indication (2-color indication) D-H7, H7P, H7 D-G5T ith timer Grommet (In-line) D-53 D-93V, 96V Reed switch D-C73, C76 D-9V one D-C8 * Solid state switches with pre-wired connector are also available. or detailes, refer to est Pneumatics catalog. pplicable bore size 44 to 2 75 to 2 44 to 2 54

64 Series CM uto Switch Specifications uto Switch Common Specifications Type Reed switch Solid state switch eakage current one 3-wire: 1 μ or less 2-wire:.8 m or less perating time Impact resistance 1.2 ms 3 m/s 2 1 ms or less 1 m/s 2 Insulation resistance 5 MΩ or more at 5 VDC Mega (between lead wire and case) ithstand voltage 15 VC for 1 minute (between lead wire and case) ote) 1 VC for 1 minute (between lead wire and case) mbient temperature Enclosure Standard 1 to 6 C IEC6529 standard IP67 Conforming to CE ote) D-C73C/C8C type: 1 VC/min. (etween lead wire and case) ead ire ead wire length indication (Example) D-M9 ote 1) pplicable auto switch with 5 m lead wire Z Solid state switch: Manufactured upon receipt of order as standard. ote 2) 1 m (M): D-M9 only. ote 3) ead wire tolerance ead wire length Tolerance.5 m ±15 mm 1 m ±3 mm 3 m ±9 mm 5 m ±15 mm ead wire length il.5 m M 1 m 3 m Z 5 m Solid state switch with oilproof flexible heavy-duty vinyl cord indication To designate solid state switches with flexible specifications, add -61 after the lead wire length. lexible cable is used for D-M9, D-M9 as standard. There is no need to place the suffix -61 at the end of the part number. (Example) D-H7-61 lexible specification ead wires with connector indication Part o. of ead ires with Connectors Model D-C5 D-C3 D-C5 ead wire length.5 m 3 m 5 m (pplicable for connector type only) Contact Protection oxes: CD-P11, CD-P12 <pplicable switch model> D-9/9V/C7/C8/C73C/C8C type The auto switches below do not have a built-in contact protection circuit. contact protection box is not required for solid state switches due to their construction. Therefore, please use a contact protection box with the switch for any of the following cases: here the operation load is an inductive load. here the wiring length to the load is greater than 5 m. here the load voltage is 1 VC. The contact life may be shortened (due to permanent energizing conditions). here the load voltage is 11 VC. here the load voltage is increased by 1% of the rated voltage for the above applicable auto switch model (except for D-C73C, C8C), you can use the auto switches at a load voltage of 11 VC by using a contact protection box (CD-P11) and setting the load current within the current range in which the maximum load current is decreased by 1%. Specifications Part no. oad voltage Max. load current ead wire length CD-P11 1 VC 2 VC 25 m 12.5 m Switch connection side.5 m oad connection side.5 m CD-P12 24 VDC 5 m Internal Circuit CD-P11 CD-P12 Dimensions Connection Surge absorber Zener diode SMC VT CD P Choke coil Choke coil UT rown UT lue UT (+) rown UT () lue 9 SITCH 38 ø To connect a switch unit to a contact protection box, connect the lead wire from the side of the contact protection box marked SITCH to the lead wire coming out of the switch unit. eep the switch as close as possible to the contact protection box, with a lead wire length of no more than 1 meter.

65 asic iring uto Switch Connections and Examples Solid state 3-wire, P Switch main circuit (Power supplies for switch and load are separate.) Switch main circuit rown oad lack lue rown oad lack lue Solid state 3-wire, PP Switch main circuit rown 2-wire (Solid state) Example of Connection to PC (Programmable ogic Controller) lack lue oad Switch main circuit Switch main circuit rown oad lue rown oad lue 2-wire (Reed) Indicator light protective circuit etc. Indicator light protective circuit etc. rown oad lue rown oad lue Sink input specification 3-wire, P lack Input rown Switch Source input specification 3-wire, PP lack Input rown Switch Connect according to the applicable PC input specifications, since the connection method will vary depending on the PC input specifications. lue lue 2-wire rown CM Input PC internal circuit 2-wire lue CM Input PC internal circuit Switch Switch lue CM 3-wire D connection for P output (using relays) 2-wire with 2-switch D connection PC internal circuit rown Example of D (Serial) and R (Parallel) Connection Switch 1 Switch 2 Switch 1 Switch 2 rown lack lue Relay rown lack Relay lue rown lue rown lue oad oad Relay contact hen two switches are connected in series, a load may malfunction because the load voltage will decrease when in the state. The indicator lights will illuminate if both of the switches are in the state. Power supply Residual oad voltage at = x 2 pcs. voltage voltage = 24 V - 4 V x 2 pcs. = 16 V Example: Power supply is 24 VDC. Internal voltage drop in switch is 4 V. CM PC internal circuit D connection for P output (performed with switches only) rown lack Switch 1 oad lue rown lack Switch 2 lue The indicator lights will illuminate when both switches are turned. R connection for P output Switch 1 Switch 2 2-wire with 2-switch R connection (Solid state) rown hen two switches oad are connected in parallel, a malfunction Switch 1 lue may occur because the load voltage will rown Switch 2 increase when in the state. lue oad voltage at = eakage current x 2 pcs. x oad impedance = 1 m x 2 pcs. x 3 kω = 6 V Example: oad impedance is 3 kω. eakage current from switch is 1 m. rown lack lue rown lack lue oad (Reed) ecause there is no current leakage, the load voltage will not increase when turned. However, depend-ing on the number of switches in the state, the indicator lights may sometimes dim or not light because of the dispersion and reduction of the current flowing to the switches. 56

66 Solid State Switch: Direct Mounting Style D-M9(V)/D-M9P(V)/D-M9(V) Grommet 2-wire load current is reduced (2.5 to 4 m). lexibility is 1.5 times greater than the conventional model (SMC comparison). Using flexible cable as standard spec. Caution Precautions ix the switch with appropriate screw installed on the switch body. If using other screws, the switch may be damaged. uto Switch Internal Circuit D-M9(V) DC (+) rown uto Switch Specifications PC: Programmable ogic Controller D-M9(V) (ith indicator light) uto switch model D-M9 D-M9V D-M9P D-M9PV D-M9 D-M9V Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular iring type 3-wire 2-wire utput type P PP pplicable load Power supply voltage Current consumption IC circuit, Relay, PC 5, 12, 24 VDC (4.5 to 28 V) 1 m or less 24 VDC relay, PC oad voltage 28 VDC or less 24 VDC (1 to 28 VDC) oad current 4 m or less 2.5 to 4 m Internal voltage drop eakage current.8 V or less at 1 m (2 V or less at 4 m) 1 μ or less at 24 VDC 4 V or less.8 m or less Indicator light Standards Red ED illuminates when turned. CE marking ead wires ilproof heavy-duty vinyl cable: ø2.7 x 3.2 ellipse D-M9(V).15 mm 2 x 2 cores D-M9(V), D-M9P(V).15 mm 2 x 3 cores ote 1) Refer to page 58 for solid state switch common specifications. ote 2) Refer to page 58 for lead wire lengths. eight Dimensions D-M9 uto switch model ead wire length (m) D-M9(V) Indicator light D-M9P(V) D-M9(V) Unit: g Unit: mm Switch main circuit UT lack DC () lue 2.6 SMC M2.5 X 4 long Slotted set screw 22 D-M D-M9P(V) DC (+) rown 4 6 Most sensitive position Switch main circuit UT lack D-M9V DC () lue 4.6 D-M9(V) UT (+) rown M2.5 X 4 long Slotted set screw 2.7 Indicator light Switch main circuit UT () lue 2.6 ø4 6 Most sensitive position 57

67 Solid State Switch: and Mounting Style D-H7C Connector Caution perating Precautions 1.Confirm that the connector is appropriately tightened. If tightened insufficiently, the waterproof performance will deteriorate. 2. or how to handle a connector, refer to est Pneumatics catalog. uto Switch Internal Circuit UT (+) rown uto Switch Specifications PC: Programmable ogic Controller D-H7C (ith indicator light) uto switch part no. D-H7C iring type 2-wire utput type pplicable load 24 VDC Relay, PC Power supply voltage Current consumption oad voltage 24 VDC (1 to 28 VDC) oad current 5 to 4 m Internal voltage drop 4 V or less eakage current.8 m or less at 24 VDC Indicator light Red ED illuminates when. Standard Conforming to CE ead wires ilproof heavy-duty vinyl cable: ø3.4,.2 mm 2 x 2 cores (rown, lue),.5 m ote 1) Refer to page 58 for solid state switch common specifications. ote 2) Refer to page 58 for lead wire lengths and lead wire with connector. eight uto switch part no. ead wire length (m) D-H7C Unit: g Switch main circuit Dimensions Unit: mm UT () lue Indicator light ø3.5 Mounting Hole ø1 ø Most sensitive position 58

68 2-Color Indication Solid State Switch: Direct Mounting Style D-M9(V)/D-M9P(V)/D-M9(V) Grommet 2-wire load current is reduced (2.5 to 4 m). RoHS compliant lexibility is 1.5 times greater than the conventional model (SMC comparison). Using flexible cable as standard spec. The optimum operating position can be determined by the color of the light. (Red Green Red) uto Switch Specifications PC: Programmable ogic Controller D-M9/D-M9V (ith indicator light) uto switch part no. D-M9 D-M9V D-M9P D-M9PV D-M9 D-M9V Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular iring type utput type 3-wire P PP 2-wire pplicable load Power supply voltage Current consumption IC circuit, Relay, PC 5, 12, 24 VDC (4.5 to 28 V) 1 m or less 24 VDC relay, PC oad voltage 28 VDC or less 24 VDC (1 to 28 VDC) oad current 4 m or less 2.5 to 4 m Internal voltage drop eakage current.8 V or less at 1 m (2 V or less at 4 m) 1 μ or less at 24 VDC 4 V or less.8 m or less Indicator light Standard perating position... Red ED illuminates. ptimum operating position... Green ED illuminates. Conforming to CE ead wires ilproof flexible heavy-duty vinyl cable: ø2.7 x 3.2 ellipse D-M9(V).15 mm 2 x 2 cores D-M9(V), D-M9P(V).15 mm 2 x 3 cores ote 1) Refer to page 58 for solid state switch common specifications. ote 2) Refer to page 58 for lead wire lengths. uto Switch Internal Circuit D-M9(V) Switch main circuit DC (+) rown UT lack eight uto switch part no. ead wire length (m) D-M9(V) D-M9P(V) Unit: g D-M9(V) DC () lue Dimensions Unit: mm D-M9P(V) D-M9 Indicator light DC (+) rown SMC Switch main circuit UT lack M2.5 X 4 long Slotted set screw DC () lue D-M9(V) 4 6 Most sensitive position Switch main circuit UT (+) rown D-M9V UT () lue Indicator light / Display method perating range M2.5 X 4 long Slotted set screw Indicator light Display Red Green Red 9.5 ptimum operating position 2.6 ø4 6 Most sensitive position 59

69 ater Resistant 2-Color Indication Solid State Switch: and Mounting Style D-H7 Grommet ater (coolant) resistant type The optimum operating position can be determined by the color of the light. (Red Green Red) uto Switch Specifications D-H7 (ith indicator light) uto switch part no. iring type utput type pplicable load Power supply voltage Current consumption oad voltage oad current Internal voltage drop eakage current PC: Programmable ogic Controller D-H7 2-wire 24 VDC Relay, PC 24 VDC (1 to 28 VDC) 5 to 4 m 4 V or less.8 m or less at 24 VDC Caution perating Precautions Consult SMC if using coolant liquid other than water based solution. Indicator light Standard perating position... Red ED illuminates. ptimum operating position... Green ED illuminates. Conforming to CE ead wires ilproof heavy-duty vinyl cable: ø3, ø4,.2 mm 2 x 2 cores (rown, lue), 3 m (Standard) ote 1) Refer to page 58 for solid state switch common specifications. ote 2) Refer to page 58 for lead wire lengths. eight Unit: g uto Switch Internal Circuit uto switch part no..5 ead wire length 3 (m) 5 D-H UT (+) rown Dimensions Unit: mm Switch main circuit UT () lue ø3.4 Indicator light / Display method Indicator light perating range 4.3 ø3.5 Display Red Green Red ptimum operating position Most sensitive position 6

70 2-Color Indication with Diagnostic utput Solid State Switch: and Mounting Style D-H7 Grommet Since the output signal can be detected in an unsteady detecting area, the difference of detecting position can be confirmed by the side of PC (Programmable ogic Controller). The optimum operating position can be determined by the color of the light. (Red Green Red) uto Switch Specifications PC: Programmable ogic Controller D-H7 (ith indicator light) uto switch part no. D-H7 iring type 4-wire utput type P Diagnostic output type ormal operation pplicable load IC circuit, Relay, PC Power supply voltage 5, 12, 24 VDC (4.5 to 28 VDC) Current consumption 1 m or less oad voltage 28 VDC or less oad current 5 m or less at the total amount of normal output and diagnostic output Internal voltage drop 1.5 V or less (.8 V or less at 5 m) eakage current 1 μ or less at 24 VDC perating position... Red ED illuminates. Indicator light ptimum operating position... Green ED illuminates. Standard Conforming to CE ead wires ilproof heavy-duty vinyl cable: ø3.4,.2 mm 2 x 4 cores (rown, lack, range, lue),.5 m ote 1) Refer to page 58 for solid state switch common specifications. ote 2) Refer to page 58 for lead wire lengths. uto Switch Internal Circuit eight Unit: g DC (+) rown UT (ormal output) lack uto switch part no..5 ead wire length 3 (m) 5 D-H Switch main circuit Diagnosis UT (Diagnostic output) range DC () lue Diagnostic utput peration The diagnostic signal is output within unsteady detecting area (where indicator light is Red), and the diagnostic output becomes when the detecting position remains within the optimum operating position (where indicator is Green). hen the detecting position is not adjusted, the diagnostic output becomes. Dimensions Indicator light UT (ormal output) Diagnosis UT (Diagnostic output) Red Green Red Red Unit: mm ø ø3.5 Indicator light Most sensitive position 61

71 Reed Switch: Direct Mounting Style D-9(V)/D-93(V)/D-96(V) Grommet Caution Precautions ix the auto switch with the existing screw installed on the switch body. The auto switch may be damaged if a screw other than the one supplied is used. uto Switch Internal Circuit D-9(V) Reed switch D-93(V) Reed switch ED diode Resistor Zener diode rown lue Contact protection box CD-P11 CD-P12 Contact protection box CD-P11 CD-P12 UT (±) rown UT (±) lue UT (+) rown UT () lue uto Switch Specifications D-9(V) (ithout indicator light) uto switch model pplicable load oad voltage 24 VC/DC or less Maximum load current 5 m Contact protection circuit Internal resistance Standards D-9/D-9V IC circuit, Relay, PC PC: Programmable ogic Controller 48 VC/DC or less 1 VC/DC or less 4 m 2 m one 1 Ω or less (including lead wire length of 3 m) CE marking D-93(V)/D-96(V) (ith indicator light) uto switch model pplicable load oad voltage 24 VDC D-93/D-93V Relay, PC 1 VC D-96/D-96V IC circuit 4 to 8 VDC oad current range and max. load current ote 3) 5 to 4 m 5 to 2 m 2 m Contact protection circuit one Internal resistance D V or less (to 2 m)/3 V or less (to 4 m) D-93V 2.7 V or less.8 V or less Indicator light Standards Red ED illuminates when turned. CE marking ead wires D-9(V)/D-93(V) ilproof heavy-duty vinyl cable: ø2.7,.18 mm 2 x 2 cores (rown, lue),.5 m D-96(V) ilproof heavy-duty vinyl cable: ø2.7,.15 mm 2 x 3 cores (rown, lack, lue),.5 m ote 1) Refer to page 58 for reed switch common specifications. ote 2) Refer to page 58 for lead wire lengths. ote 3) Under 5 m, the visuality of an indicator light is worsen. urthermore, although it could be impossible to recognize it under 2.5 m, but there would be no problem only with 1 m or more in terms of the contact output. eight Model ead wire length (m).5 3 D Dimensions D-9/D-93/D-96 D-9V 6 3 D D-93V 6 3 ø2.7 D (g) D-96V 8 41 Unit: mm D-96(V) DC (+) ED diode rown Resistor oad Reverse UT current lack prevention diode Reed switch DC () lue (+) DC power supply () 4 M2.5 x 4 l Slotted set screw D-9V/D-93V/D-96V 1 22 (24.5) Indicator light D-9 type comes without indicator light. Most sensitive position ( ): D-93 ote) q In a case where the operation load is an inductive load. w In a case where the wiring load is greater than 5 m. e In a case where the load voltage is 1 VC. Use the auto switch with a contact protection box in any of the above mentioned cases. (or details about the contact protection box, refer to page 58.) ø2.7 Most sensitive position M2.5 x 4 l Slotted set screw 2 22 Indicator light D-9 type comes without indicator light. 6 62

72 Reed Switch: and Mounting Style D-54/D-64 Grommet uto Switch Internal Circuit D-54 UT () lue Reed switch Zener diode Resistor ED diode Surge absorber Choke coil UT (+) rown uto Switch Specifications PC: Programmable ogic Controller D-5 (ith indicator light) uto switch part no. pplicable load D-54 Relay, PC oad voltage oad current range ote 3) 24 VDC 5 to 5 m 1 VC 5 to 25 m 2 VC 5 to 12.5 m Contact protection circuit uilt-in Internal voltage drop Indicator light Standard 2.4 V or less (to 2 m)/3.5 V or less (to 5 m) Red ED illuminates when turned. Conforming to CE D-6 (ithout indicator light) uto switch part no. pplicable load D-64 Relay, PC oad voltage Maximum load current 24 VC/DC or less Max. 5 m 1 VC Max. 25 m 2 VC Max m Contact protection circuit Internal resistance Standard uilt-in 25 Ω or less Conforming to CE ead wires ilproof heavy-duty vinyl cable: ø4,.3 mm 2 x 2 cores (rown, lue),.5 m ote 1) Refer to page 58 for reed switch common specifications. ote 2) Refer to page 58 for lead wire lengths. ote 3) Under 5 m, the strength of the indicator light is poor. In some cases, visibility of the indicator light will not be possible where the output signal is less than 2.5 m. However, there is no problem in terms of contact output, when an output signal exceeds 1 m or more. eight uto switch part no..5 ead wire length 3 (m) 5 D D Unit: g D-64 Choke coil Dimensions Unit: mm UT ( ) lue ± Reed switch UT (±) rown Surge absorber 14.3 SMC ø Indicator light D-64 type comes without indicator light ø Most sensitive position 63

73 Reed Switch: and Mounting Style D-C73C/D-C8C Connector Caution perating Precautions 1.Confirm that the connector is appropriately tightened. If tightened insufficiently, the waterproof performance will deteriorate. 2. or how to handle a connector, refer to est Pneumatics 24 Vol. 6 catalog. uto Switch Internal Circuit D-C73C Reed switch ED diode D-C8C Resistor Zener diode Contact protection box CD-P12 Choke coil rown lue Zener diode UT (+) rown UT () lue uto Switch Specifications PC: Programmable ogic Controller D-C73C (ith indicator light) uto switch part no. D-C73C pplicable load Relay, PC oad voltage 24 VDC oad current range ote 4) 5 to 4 m Contact protection circuit one Internal voltage drop 2.4 V or less Indicator light Red ED illuminates when turned. Standard Conforming to CE D-C8C (ithout indicator light) uto switch part no. D-C8C pplicable load Relay, PC oad voltage 24 VC/DC or less Maximum load current 5 m Contact protection circuit one Internal resistance 1 Ω or less (including lead wire length of 3 m) Standard Conforming to CE ead wires ilproof heavy-duty vinyl cable: ø3.4,.2 mm 2 x 2 cores (rown, lue),.5 m ote 1) Refer to page 58 for reed switch common specifications. ote 2) Refer to page 58 for lead wire lengths. ote 3) ead wire with connector may be shipped with switch. ote 4) Under 5 m, the strength of the indicator light is poor. In some cases, visibility of the indicator light will not be possible where the output signal is less than 2.5 m. However, there is no problem in terms of contact output, when an output signal exceeds 1 m or more. eight uto switch part no. ead wire length (m) D-C73C D-C8C Unit: g Reed switch Contact protection box CD-P11 CD-P12 UT (±) rown UT ( ) lue ± Dimensions ø1 Unit: mm ote) In a case where the operation load is an inductive load. In a case where the wiring load is greater than 5 m. Use the contact protection box in any of the above listed situations. The contact point life may decrease. (Refer to page 58 for contact protection box.) ø3.5 Indicator light D-C8C type comes without indicator light 14 ø Most sensitive position 26 64

74 2-Color Indication Reed Switch: and Mounting Style D-59 Grommet The optimum operating position can be determined by the color of the light. (Red Green Red) uto Switch Internal Circuit D-59 uto Switch Specifications D-59 (ith indicator light) uto switch part no. pplicable load oad voltage oad current range ote 3) Contact protection circuit Internal voltage drop Indicator light Standard D-59 Relay, PC 24 VDC 5 to 4 m uilt-in 4 V or less Conforming to CE ead wires ilproof heavy-duty vinyl cable: ø4,.3 mm 2 x 2 cores (rown, lue),.5 m ote 1) Refer to page 58 for reed switch common specifications. ote 2) Refer to page 58 for lead wire lengths. ote 3) Under 5 m, the strength of the indicator light is poor. In some cases, visibility of the indicator light will not be possible where the output signal is less than 2.5 m. However, there is no problem in terms of contact output, when an output signal exceeds 1 m or more. eight PC: Programmable ogic Controller perating position... Red ED illuminates. ptimum operating position... Green ED illuminates. Unit: g Switch main circuit Choke coil Reed switch Zener diode ED UT (+) rown UT () lue Indicator light / Display method uto switch part no. ead wire length (m) Dimensions D Unit: mm perating range Display Red Green Red ptimum operating position ø4.5 Indicator light ø Most sensitive position 65

75 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, arning or Danger. They are all important notes for safety and must be followed in addition to International Standards (IS/IEC), Japan Industrial Standards (JIS) 1) and other safety regulations 2). 1) IS 4414: Pneumatic fluid power General rules relating to systems. IS 4413: Hydraulic fluid power General rules relating to systems. IEC 624-1: Safety of machinery Electrical equipment of machines. (Part 1: General requirements) IS : Manipulating industrial robots -Safety. JIS 837: General rules for pneumatic equipment. JIS 8361: General rules for hydraulic equipment. JIS 996-1: Safety of machinery Electrical equipment of machines. (Part 1: General requirements) JIS : Manipulating industrial robots - Safety. etc. 2) abor Safety and Sanitation aws, etc. Caution: perator error could result in injury or equipment damage. arning: perator error could result in serious injury or loss of life. Danger : In extreme conditions, there is a possibility of serious injury or loss of life. arning 1. The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifications. Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalog information, with a view to giving due consideration to any possibility of equipment failure when configuring the equipment. 2. nly personnel with appropriate training should operate machinery and equipment. The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2. hen the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully. 3. efore machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction. 4. Contact SMC beforehand and take special consideration of safety measures if the product is to be used in any of the following conditions. 1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifications described in the product catalog. 3. n application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. ack page 1

76 Safety Instructions Caution The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary. If anything is unclear, contact your nearest sales branch. (1-8-SMC-SMC1) imited arranty and Disclaimer/Compliance Requirements The product used is subject to the following imited arranty and Disclaimer and Compliance Requirements. Read and accept them before using the product. imited arranty and Disclaimer 1. The warranty period of the product is 1 year in service or 1.5 years after the product is delivered. 3) lso, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2. or any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product. 3. Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the specified catalog for the particular products. 3) Vacuum pads are excluded from this 1 year warranty. vacuum pad is a consumable part, so it is warranted for a year after it is delivered. lso, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. Compliance Requirements hen the product is exported, strictly follow the laws required by the Department of Commerce, International Trade dministration (oreign Exchange and oreign Trade Control aw). ack page 2

77 Series CM ctuators Precautions 1 e sure to read this before handling. arning 1. There is a danger of sudden action by air cylinders if sliding parts of machinery are twisted, etc., and changes in forces occur. In such cases, human injury may occur; e.g., by catching hands or feet in the machinery, or damage to the machinery itself may occur. Therefore, the machine should be designed to avoid such dangers. 2. Install a protective cover when there is a risk of human injury If a driven object and moving parts of a cylinder pose a danger of human injury, design the structure to avoid contact with the human body. 3. Securely tighten all stationary parts and connected parts so that they will not become loose. Especially when a cylinder operates with high frequency or is installed where there is a lot of vibration, ensure that all parts remain secure. 4. deceleration circuit may be required. hen a driven object is operated at high speed or the load is heavy, a cylinder s cushion will not be sufficient to absorb the impact. Install a deceleration circuit to reduce the speed before cushioning to relieve the impact. In this case, the rigidity of the machinery should also be examined. 5. Consider a possible drop in operating pressure due to a power outage, etc. hen a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc. Therefore, safety equipment should be installed to prevent damage to machinery and/or human injury. Suspension mechanisms and lifting devices also require consideration for drop prevention. 6. Consider a possible loss of power source. Measures should be taken to protect against human injury and equipment damage in the event that there is a loss of power to equipment controlled by air pressure, electricity or hydraulics, etc. 7. Design circuitry to prevent sudden lurching of driven objects. hen a cylinder is driven by an exhaust center type directional control valve or when starting up after residual pressure is exhausted from the circuit, etc., the piston and its driven object will lurch at high speed if pressure is applied to one side of the cylinder because of the absence of air pressure inside the cylinder. Therefore, select equipment and design circuits to prevent sudden lurching, because there is a danger of human injury and/or damage to equipment when this occurs. 8. Consider emergency stops. Design so that human injury and/or damage to machinery and equipment will not be caused when machinery is stopped by a safety device under abnormal conditions, such as a power outage or a manual emergency stop. Design and Selection 9. Consider the action when operation is restarted after an emergency stop or abnormal stop. Design the machinery so that human injury or equipment damage will not occur upon restart of operation. hen the cylinder has to be reset at the starting position, install safe manual control equipment. arning 1. Confirm the specifications. The products advertised in this catalog are designed according to use in industrial compressed air systems. If the products are used in conditions where pressure, temperature, etc., are out of specification, damage and/or malfunction may be caused. Do not use in these conditions. (Refer to the specifications.) Consult SMC if you use a fluid other than compressed air. 2. Intermediate stops hen intermediate stopping of a cylinder piston is performed with a 3 position closed center type directional control valve, it is difficult to achieve stopping positions as accurate and precise as with hydraulic pressure due to the compressibility of air. urthermore, since valves and cylinders, etc., are not guaranteed for zero air leakage, it may not be possible to hold a stopped position for an extended period of time. Contact SMC in case it is necessary to hold a stopped position for an extended period. Caution 1. perate within the limits of the maximum usable stroke. The piston rod will be damaged if operated beyond the maximum stroke. Refer to the air cylinder model selection procedure for the maximum useable stroke. 2. perate the piston within a range such that collision damage will not occur at the stroke end. perate within a range such that damage will not occur when the piston having inertial force stops by striking the cover at the stroke end. Refer to the cylinder model selection procedure for the range within which damage will not occur. 3. Use a speed controller to adjust the cylinder drive speed, gradually increasing from a low speed to the desired speed setting. 4. Provide intermediate supports for long stroke cylinders. Provide intermediate supports for cylinders with long strokes to prevent rod damage due to sagging of the rod, deflection of the tube, vibration and external loads, etc. It is assumed the persons determining the stroke requirements have technical training and expertise in the design limitations of pneumatic equiptment and are aware that death, personal injury, and property damage may result from the improper use of these products. Proper use is the users responsibilty. ack page 3

78 Series CM ctuators Precautions 2 e sure to read this before handling. Caution Mounting 1. e certain to align the rod axis with the load and direction of movement when connecting. hen not properly aligned, the rod and tube may be twisted, and damage may be caused due to wear on areas such as the inner tube surface, bushings, rod surface and seals. 2. hen an external guide is used, connect the rod end and the load in such a way that there is no interference at any point within the stroke. 3. Do not scratch or gouge the sliding parts of the cylinder tube or piston rod, etc., by striking or grasping them with other objects. Cylinder bores are manufactured to precise tolerances, so that even a slight deformation may cause malfunction. lso, scratches or gouges, etc., in the piston rod may lead to damaged seals and cause air leakage. 4. Prevent the seizure of rotating parts. Prevent the seizure of rotating parts (pins, etc.) by applying grease. 5. Do not use until you can verify that equipment can operate properly. Verify correct mounting by appropriate function and leakage inspections after compressed air and power are connected following mounting, maintenance or conversions. 6. Instruction manual The product should be mounted and operated after thoroughly reading the manual and understanding its contents. eep the instruction manual where it can be referred to as needed. 7. Preparation before piping efore piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil and other debris from inside the pipe. 8. rapping of pipe tape hen screwing together rapping direction pipes and fittings, etc., be certain that chips from the pipe threads and sealing material do not get inside Pipe tape the piping. lso, when pipe tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. 9. Mount an auto switch at the center of the operating range. djust the mounting position of an auto switch so that the piston stops at the center of the operating range (the range in which a switch is ). (The mounting position shown in the catalog indicates the optimum position at stroke end.) If mounted at the end of the operating range (around the borderline of and ), operation will be unstable. Expose approx. 2 threads Caution arning arning Cushion 1. Readjust using the cushion needle. Cushion is adjusted at the factory, however, the cushion needle on the cover should be readjusted when the product is put into service, based upon factors such as the size of the load and the operating speed. hen the cushion needle is turned clockwise, the restriction becomes smaller and the cushion's effectiveness is increased. Tighten the lock nut securely after adjustment is performed. 2. Do not operate with the cushion needle in a fully closed condition. This will cause damage to the seals. 1. Use clean air. Do not use compressed air which includes chemicals, synthetic oils containing organic solvents, salt or corrosive gases, etc., as it can cause damage or malfunction. Caution 1. Install air filters. Install air filters at the upstream side of valves. The filtration degree should be 5 μm or finer. 2. Install an after-cooler, air dryer or water separator, etc. ir that includes excessive drainage may cause malfunction of valves and other pneumatic equipment. To prevent this, install an after-cooler, air dryer or water separator, etc. 3. Use the product within the specified range of fluid and ambient temperature. Take measures to prevent freezing, since moisture in circuits can be frozen below 5 C, and this may cause damage to seals and lead to malfunction. Refer to est Pneumatics 24 Vol.14 catalog for further details on compressed air quality. Maintenance 1. Removal of equipment, and supply/exhaust of compressed air. hen equipment is removed, first check measures to prevent dropping of driven objects and run-away of equipment, etc. Then cut off the supply pressure and electric power, and exhaust all compressed air from the system. hen machinery is restarted, proceed with caution after confirming measures to prevent cylinder from lurching. Caution 1. Drain flushing Remove drainage from air filters regularly. (Refer to the specifications.) ack page 4

79 Series CM uto Switches Precautions 1 e sure to read this before handling. arning 1. Confirm the specifications. Read the specifications carefully and use this product appropriately. The product may be damaged or malfunction if it is used outside the range of specifications for current load, voltage, temperature or impact. 2. Cautions for use in an interlock circuit hen an auto switch is used for an interlock signal requiring high reliability, devise a double interlock system to avoid trouble by providing a mechanical protection function, or by also using another switch (sensor) together with the auto switch. lso, perform periodic maintenance and confirm proper operation. 3. Do not make nay modifications (including exchanging the printed circuit boards) to the product. It may cause human injuries and accidents. Design and Selection Caution 1. Pay attention to the length of time that a switch is at an intermediate stroke position. hen an auto switch is placed at an intermediate position of the stroke and a load is driven at the time the piston passes, the auto switch will operate, but if the speed is too great the operating time will be shortened and the load may not operate properly. The maximum detectable piston speed is: uto switch operating range (mm) V (mm/s) = x 1 Time load applied (ms) In cases of high piston speed, the use of an auto switch (G5T) with a built-in delay timer ( 2 ms) makes it possible to extend the load operating time. 2. eep wiring as short as possible. <Reed switches> s the length of the wiring to a load gets longer, the rush current at switching becomes greater, and this may shorten the product s life. (The switch will stay all the time.) 1) Use a contact protection box when the wire length is 5 m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 3 m long, it is not able to adequately absorb the rush current and its life may be reduced. It is again necessary to connect a contact protection box in order to extend its life. Please contact SMC in this case. <Solid state switches> 3) lthough wire length should not affect switch function, use a wire 1 m or shorter. If the wiring is longer it will likely increase noise although the length is less than 1 m. hen the wire length is long, we recommend attaching the ferrite core to the both ends of the cable to prevent excess noise. contact protection box is not required for solid state switches due to their construction. 3. Do not use a load that generates surge voltage. If a surge voltage is generated, the discharge occurs at the contact, possibly resulting in the shortening of product life. <Reed switches> If driving a load such as a relay that generates a surge voltage, use an auto switch with built-in contact protection circuit or use a contact protection box. <Solid state switches> lthough a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. hen a load, such as a relay or solenoid which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 4. Take precautions when multiple cylinders (actuators) are used close together. hen multiple auto switch cylinders (actuators) are used in close proximity, magnetic field interference may cause the auto switches to malfunction. Maintain a minimum cylinder separation of 4 mm. (hen the allowable interval is specified for each cylinder series, use the indicated value.) The auto switches may malfunction due to the interference from the magnetic fields. ack page 5

80 Caution Series CM uto Switches Precautions 2 e sure to read this before handling. 5. Pay attention to the internal voltage drop of the auto switch. <Reed switches> 1) uto switches with an indicator light (Except D-96, C76) If auto switches are connected in series as shown below, take note that there will be a large voltage drop because of internal resistance in the light emitting diodes. (Refer to the internal voltage drop in the auto switch specifications.) [The voltage drop will be n times larger when n auto switches are connected.] Even though an auto switch operates normally, the load may not operate. In the same way, when operating under a specified voltage, although an auto switch may operate normally, the load may not operate. Therefore, the formula below should be satisfied after confirming the minimum operating voltage of the load. Supply voltage Internal voltage drop of auto switch > Minimum operating voltage of load 2) If the internal resistance of a light emitting diode causes a problem, select an auto switch without an indicator light (Model D-9, C8). <Solid state switches> 3) Generally, the internal voltage drop will be greater with a 2- wire solid state auto switch than with a reed switch. Take the same precautions as in 1). lso, note that a 12 VDC relay is not applicable. 6. Pay attention to leakage current. <Solid state switches> ith a 2-wire solid state auto switch, current (leakage current) flows to the load to operate the internal circuit even when in the state. perating current of load ( condition) > eakage current If the criteria given in the above formula are not met, it will not reset correctly (stays ). Use a 3-wire switch if this specification will not be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. 7. Ensure sufficient clearance for maintenance activities. hen designing an application, be sure to allow sufficient clearance for maintenance and inspections. Design and Selection oad arning 8. hen multiple auto switches are required n indicates the number of auto switch which can be physically mounted. Detection intervals depends on the auto switch mounting structure and set position therefore some required interval and set positions may not be available. 9. imitations of detectable positioning hen using certain mounting brackets, the surface and position where an auto switch can be mounted maybe restricted due to physical interference. or example, when using some bracket types the auto switch cannot be surface mounted at the bottom side of foot bracket, etc. Please select the set position of the auto switch so that it does not interfere with the rear plate of the cylinder. 1. Use the cylinder and auto switch in proper combination. The auto switch is pre-adjusted to activate properly for an autoswitch-capable SMC cylinder. If the auto switch is mounted improperly, used for another brand of cylinder or used after the alternation of the machine installation, the auto switch may not activate properly. Caution Mounting and djustment 1. Do not drop or bump. Do not drop, bump or apply excessive impacts (3 m/s 2 or more for reed switches and 1 m/s 2 or more for solid state switches) while handling. lthough the body of the auto switch may not be damaged, the inside of the auto switch could be damaged and cause a malfunction. 2. Mount auto switches using the proper tightening torque. If an auto switch is tightened beyond the range of tightening torque, the auto switch mounting screws, auto switch mounting brackets or auto switch may be damaged. n the other hand, tightening below the range of tightening torque may allow the auto switch to slip out of position. (Refer to the auto switch mounting instructions for each series for auto switch mounting, moving, and tightening torque, etc.) 3. Do not carry a cylinder by the auto switch lead wires. ever carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the auto switch to be damaged by the stress. 4. ix the auto switch with appropriate screw installed on the switch body. If using other screws, auto switch may be damaged. ack page 6

81 Series CM uto Switches Precautions 3 e sure to read this before handling. Caution iring 1. Confirm proper insulation of wiring. e certain that there is no faulty wiring insulation (contact with other circuits, ground fault, improper insulation between terminals, etc.). Damage may occur due to excess current flow into a switch. 2. Do not wire with power lines or high voltage lines. ire separately from power lines or high voltage lines, avoiding parallel wiring or wiring in the same conduit with these lines. Control circuits containing auto switches may malfunction due to noise from these other lines. 3. void repeatedly bending or stretching lead wires. roken lead wires will result from repeatedly applying bending stress or stretching force to the lead wires. Stress and tensile force applied to the connection between the cable and auto switch increases the possibility of disconnection. ix the cable in the middle so that it is not movable in the area where it connects with the auto switch. 4. e sure to connect the load before power is applied. <2-wire type> If the power is turned when an auto switch is not connected to a load, the auto switch will be instantly damaged because of excess current. It is the same as when the 2-wire brown cord (+, output) is directly connected to the (+) power supply terminal. 5. Do not allow short circuit of loads. <Reed switches> If the power is turned with a load in a short circuited condition, the auto switch will be instantly damaged because of excess current flow into the switch. <Solid state switches> ll models of D-M9(V) except D-M9(V) and G5 and PP output type auto switches do not have built-in short circuit protection circuits. ote that if a load is short circuited, the auto switch will be instantly damaged as in the case of reed switches. Take special care to avoid reverse wiring with the brown power supply line and the black output line on 3-wire type auto switches. Caution iring 6. void incorrect wiring. <Reed switches> 24 VDC auto switch with indicator light has polarity. The brown lead wire or terminal o. 1 is (+), and the blue lead wire or terminal o. 2 is (). 1) If connections are reversed, an auto switch will operate, however, the light emitting diode will not light up. lso note that a current greater than that specified will damage a light emitting diode and it will no longer operate. pplicable model: D-93, 93V, C73, C73C, 53, 54 2) hen using a 2-color indication type auto switch (D-59), the auto switch will constantly remain if the connections are reversed. <Solid state switches> 1) If connections are reversed on a 2-wire type auto switch, the auto switch will not be damaged if protected by a protection circuit, but the auto switch will always stay in an state. However, it is still necessary to avoid reversed connections, since the auto switch could be damaged by a load short circuit in this condition. 2) If connections are reversed (power supply line + and power supply line ) on a 3-wire type auto switch, the auto switch will be protected by a protection circuit. However, if the power supply line (+) is connected to the blue wire and the power supply line () is connected to the black wire, the auto switch will be damaged. <D-M9> pplicable to D-M9(V) prior to July, 28. D-M9 does not have built-in short circuit protection circuit. e aware that if the power supply connection is reversed (e.g. (+) power supply wire and () power supply wire connection is reversed), the auto switch will be damaged. 7. hen the cable sheath is stripped, confirm the stripping direction. The insulator may be split or damaged depending on the direction. (D-M9 only) Recommended Tool Model name ire stripper Model no. D-M9-SY Stripper for a round cable (ø2.) can be used for a 2-wire type cable. ack page 7

82 Series CM uto Switches Precautions 4 e sure to read this before handling. arning 1. ever use in an atmosphere of explosive gases. The structure of auto switches is not intended to prevent explosion. ever use in an atmosphere with an explosive gas since this may cause a serious explosion. Caution 1. Do not use in an area where a magnetic field is generated. uto switches will malfunction or magnets inside cylinders will become demagnetized. (Consult SMC regarding the availability of a magnetic field resistant auto switch.) 2. Do not use in an environment where the auto switch will be continually exposed to water. lthough auto switches satisfy IEC standard IP67 construction, do not use auto switches in applications where continually exposed to water splash or spray. Poor insulation or swelling of the potting resin inside auto switches may cause malfunction. 3. Do not use in an environment with oil or chemicals. Consult SMC if auto switches will be used in an environment with coolant, cleaning solvent, various oils or chemicals. If auto switches are used under these conditions for even a short time, they may be adversely affected by improper insulation, malfunction due to swelling of the potting resin, or hardening of the lead wires. 4. Do not use in an environment with temperature cycles. Consult SMC if auto switches are used where there are temperature cycles other than normal temperature changes, as there may be adverse effects inside the auto switches. 5. Do not use in an environment where there is excessive impact shock. <Reed switches> hen excessive impact (3 m/s 2 or more) is applied to a reed switch during operation, the contact point will malfunction and generate or cut off a signal momentarily (1 ms or less). Consult SMC regarding the need to use a solid state switch depending upon the environment. 6. Do not use in an area where surges are generated. <Solid state switches> hen there are units (solenoid type lifter, high frequency induction furnace, motor, radio equipment etc.) which generate a large amount of surge in the area around cylinders with solid state auto switches, this may cause deterioration or damage to the auto switch. void sources of surge generation and disorganized lines. 7. void accumulation of iron waste or close contact with magnetic substances. hen a large amount of iron waste such as machining chips or spatter is accumulated, or a magnetic substance (something attracted by a magnet) is brought into close proximity with an auto switch cylinder, it may cause the auto switch to malfunction due to a loss of the magnetic force inside the cylinder. perating Environment Caution 8. Please consult SMC concerning water resistance, elasticity of lead wires, usage at welding sites, etc. 9. Do not use in direct sunlight. 1. Do not mount the product in locations where it is exposed to radiant heat. arning Maintenance 1. Removal of equipment, and supply/exhaust of compressed air efore any machinery or equipment is removed, first ensure that the appropriate measures are in place to prevent the fall or erratic movement of driven objects and equipment, then cut off the electric power and reduce the pressure in the system to zero. nly then should you proceed with the removal of any machinery and equipment. hen machinery is restarted, proceed with caution after confirming that appropriate measures are in place to prevent actuators from sudden movement. Caution 1. Perform the following maintenance periodically in order to prevent possible danger due to unexpected auto switch malfunction. 1) Secure and tighten auto switch mounting screws. If screws become loose or the mounting position is dislocated, retighten them after readjusting the mounting position. 2) Confirm that there is no damage to lead wires. To prevent faulty insulation, replace auto switches or repair lead wires, etc., if damage is discovered. 3) Confirm the lighting of the green light on the 2-color indicator type auto switch. Confirm that the green ED is on when stopped at the established position. If the red ED is on, the mounting position is not appropriate. Readjust the mounting position until the green ED lights up. ack page 8

83 ey eatures ccess E-Tech at Multiple methods of Product Selection. Part umber Validation. Preview and download 2D & 3D CD Models online with real-time updating. Save Parts into a custom Parts ist. Parts ists to internal groups (purchasing, maintenance) or external (partner companies, SMC sales representative). Product Selection rowse Catalog llows user to select products based on visual representation. or use when I know what I m looking for, I just don t know the part number. Part umber Validation Use Pull-Downs to make selections and build the part number. The part number is validated: ~ Partial indicates that additional entries are needed. Invalid indicates that there is a conflict between two or more values. Conflicting values are shown in red. 4 Valid part numbers can be ordered and downloaded as CD files. Select Save Part to add the part to your personal Parts ist. hen you return to the site, your Parts ist will contain all saved parts. Parts ist CD unctions Direct Entry astest method to select product. Partial part numbers or full part numbers can be entered. utomatically sets drop down options on configu-ration page. Preview and download online 2D & 3D CD. Preview parts online using a free ctivex browser applet which auto-installs the first time this function is used. The preview model matches the specified part you have configured and validated.