Flame hardening steel. The height from the reference hole to the surface of the reference support block can be selected from 2 types HIGH or LOW.

Transcription

1 is separated from the reference. INFORMTION Responses to reduction of spare parts, short lead times, and a drastic reduction of special orders Pin Plate ylinder ( machinable type) 1 HIGH type Flame hardening steel 29 mm LO type with lock (Magnetic field resistant auto switch) can be machined by the customer. (The block can be changed to a desired shape.) Note) fter machining (or even without machining), use the reference support block after it has been flame hardened. However, do not perform quenching. For machining and treatment, consult with SM. ø32 plate cylinder type Slim body: 29 mm in width Model with lock mechanism, which prevents workpiece drops during emergency stops, can be selected. 2 The height from the reference hole to the surface of the reference can be selected from 2 types HIGH or LO. Magnetic field resistant auto switches are mountable. (-P3l) H = 124 H = 54 hole H type (HIGH) L type (LO) Magnetic field resistant auto switch Possible to mount on 2 surfaces (LKU32 mounts on 1 surface) 3 Equipped with shims (3 mm) as standard. (Height can be changed.) Shims (3 mm) Shim thickness 1 mm: 2 pcs. 0.5 mm: 2 pcs. KU32 (Pin plate cylinder) ompatible with installing in narrow spaces For clamping small and lightweight workpiece and material handling, etc. pplication Examples LKU32 (Pin plate cylinder/ith lock) Unclamp direction locking rop prevention for workpiece during emergency stops ody width 29 mm chieves reduction of spare parts, short lead times, and a drastic reduction of special orders according to features,, and. (L)KU32-X E594

2 Pin Plate ylinder (L)KU32-X2359 How to Order uilt-in standard magnet type with magnetic field resistant auto switch KU R L X2359 Nil L One-way lock ithout lock ith lock during clamping ore size 32 Equiv. ø32 piston area support block machinable type Number of auto switches Nil 2 pcs. S 1 pc. (Unclamping side) diameter Symbol diameter [mm] pplicable hole diameter of workpiece [mm] shape ø13 ø18 ø20, R shape uto switch Nil ithout auto switch (uilt-in magnet) -P3S E -P3SE N -P3 L -P3L Z -P3Z * uto switches and mounting brackets are shipped together, (but not assembled). * Refer to the table below for the specifications of applicable auto switches. * hen the total thickness of clamped workpiece is over 2 mm, the auto switch may not be adjusted to the most sensitive position. lamp arm lamp arm position (viewed from top) 90 from the port side 270 from the port side lamping height (Refer to figures below) L LO type (54 mm) H HIGH type (124 mm) LO type HIGH type H = 54 H = 124 Model Examples KU32-127RH--X2359 LKU32-177RH-S-X2359 For LO type, clamp arm positions are usable only with and. hole pplicable uto Switches /Refer to the est Pneumatics No. 3 for further information on auto switches. Type uto switch model pplicable magnetic field Electrical entry Indicator light iring (Pin no. in use) Load voltage Lead wire length pplicable load -P3S Pre-wired 2-wire (3-4) magnetic field 0.3 m -P3SE connector 2-wire (1-4) Solid state (Single-phase 2-color Relay, -P3 24 V 0.5 m auto switch welding indication PL -P3L Note) magnetic field) Grommet 2-wire 3 m -P3Z 5 m Note) PL: Programmable Logic ontroller 1

3 Pin Plate ylinder (L)KU32-X2359 asic Specifications Model (L)KU32 ction ouble acting ore size (mm) 32 equivalent ylinder stroke/lamp stroke (mm) 12.5 (ithout workpiece)/10 Fluid ir Mimimum operating pressure KUl: 0.1 MPa LKUl: 0.15 MPa Maximum operating pressure 0.7 MPa mbient and fluid temperature 10 to 60 (No freezing) ushion None Lubrication Non-lube Piston speed (lamp speed) 50 to 150 mm/sec size (ylinder port) Rc1/8 Minimum operating pressure is 0.2 MPa when cylinder part and locking part use the same piping. Lock Specifications Model Locking action Unlocking pressure Lock starting pressure Locking direction size (Lock release port) Holding force (Maximum static load) LKU32 Spring locking (Exhaust locking) 0.2 MPa 0.05 MPa Unclamp direction locking Rc1/8 402 N Replacement Parts ((L)KU, LO type/high type common) Guide Pin Order No. iameter (mm) Shape lamp rm Order No. iameter (mm) Shape 12.7 / 17.7 common 19.7 Part no. KU ZL KU ZL KU ZL KU ZL KU ZL KU ZL KU ZL KU ZL Part no. KU ZL KU ZL Support lock Order No. Part no. iameter (mm) Shape 12.7 KU ZL / KU ZL 17.7 common 19.7 KU ZL lamping Force (N) diameter Operating pressure (MPa) Model (mm) (L)KU32 ø12.7 to ø Note 1) It takes approximately 0.3 seconds for the cylinder to operate to generate clamping force from an unclamping state (when no speed controller is installed). esign circuit taking into consideration the time before the clamping force is generated. Note 2) etermine the clamping force according to the strength of the workpiece. It can be damaged if the clamping force is too large. Note 3) s and clamp arms are consumable items. Please prepare spare parts in case they are damaged. eight iameter (mm) Shape (g) Model KU32-X2359 LKU32-X2359 LO type HIGH type LO type HIGH type

4 (L)KU32-X2359 imensions KU32 (lamping height LO type) T lamping direction (29) lamping direction iamond pin shape 0 ød 0.05 ø27 øe K RR hen this position is cut diagonally, the angle should be 5 or less. lamp arm Shims 3 mm ( ) utting limit line (13.3) 10 (4) (9) x Rc 1/8 54 (ithout shims: 51±0.14) 47.8 (Shim adjustment + utting limit height) (For this value or less, clamping is not possible.) x ø6h7 0 through 4 x ø6.6 through 2 surfaces x 2 x M2.5 x 0.45 (For mounting the auto switch mounting bracket) 59 (6.4) 59±0.05 ø13 through (193.5) The customer should regulate the dimensional accuracy associated with machining. If the cutting limit line is exceeded because of overmachining, clamping failures, etc. may occur and this is not covered by the warranty. 3 Pin diameter d E K R T lamp arm position lamp arm

5 Pin Plate ylinder (L)KU32-X2359 imensions KU32 (lamping height HIGH type) lamping direction T lamping direction (29) lamping direction 0 ød 0.05 ø27 øe K RR hen this position is cut diagonally, the angle should be 5 or less. 70 lamping direction lamp arm 60 iamond pin shape Shims 3 mm ( ) utting limit line (13.3) (4) 13 (9) (ithout shims: 121±0.14) (Shim adjustment + utting limit height) (For this value or less, clamping is not possible.) 14 5 (6.4) (263.5) x Rc 1/ x ø6h7 0 through 4 x ø6.6 through 2 surfaces x 2 x M2.5 x 0.45 (For mounting the auto switch mounting bracket) 59 59±0.05 ø18 through The customer should regulate the dimensional accuracy associated with machining. If the cutting limit line is exceeded because of overmachining, clamping failures, etc. may occur and this is not covered by the warranty. Pin diameter d E K R T lamp arm position lamp arm 90 from the port side 270 from the port side 4

6 (L)KU32-X2359 imensions LKU32 (lamping height LO type) T lamping direction (29) lamping direction iamond pin shape Shims 3 mm ( ) utting limit line (13.3) 0 ød 0.05 ø27 øe K RR (4) (9) hen this position is cut diagonally, the angle should be 5 or less. 54 (ithout shims: 51±0.14) 47.8 (Shim adjustment + utting limit height) (For this value or less, clamping is not possible.) lamp arm (6.4) 59± The customer should regulate the dimensional accuracy associated with machining. If the cutting limit line is exceeded because of over-machining, clamping failures, etc. may occur and this is not covered by the warranty x ø6h7 0 through ø13 through (226) Rc 1/8 Unlocking port 4 x ø6.6 through 59 2 x Rc1/8 2 surfaces x 2 x M2.5 x 0.45 (For mounting the auto switch mounting bracket) Lock ring Hexagon socket head cap screw Head side Manually unlocking 1) Remove the dustproof cover. 2) Screw the hexagon socket head cap screw (M3 x 15 L or more) into the lock ring shown on the left and raise the lock ring toward the head side. 3) The lock ring and piston rod form a right angle, and the lock is released. lamp arm position lamp arm 5 Pin diameter d E K R T

7 Pin Plate ylinder (L)KU32-X2359 imensions LKU32 (lamping height HIGH type) lamping direction T lamping direction (29) lamping direction 0 ød 0.05 ø27 øe K RR hen this position is cut diagonally, the angle should be 5 or less. 70 lamping direction lamp arm 60 iamond pin shape Shims 3 mm ( ) utting limit line (13.3) (4) 13 (9) (ithout shims: 121±0.14) (Shim adjustment + utting limit height) (For this value or less, clamping is not possible.) x ø6h7 0 through (6.4) 59±0.05 ø18 through (296) 50.5 Rc 1/8 Unlocking port 2 x Rc1/ The customer should regulate the dimensional accuracy associated with machining. If the cutting limit line is exceeded because of over-machining, clamping failures, etc. may occur and this is not covered by the warranty. 4 x ø6.6 through 59 2 surfaces x 2 x M2.5 x 0.45 (For mounting the auto switch mounting bracket) Lock ring Hexagon socket head cap screw Pin diameter d E K R T Head side Manually unlocking 1) Remove the dustproof cover. 2) Screw the hexagon socket head cap screw (M3 x 15 L or more) into the lock ring shown on the left and raise the lock ring toward the head side. 3) The lock ring and piston rod form a right angle, and the lock is released lamp arm position lamp arm 90 from the port side 270 from the port side 6

8 (L)KU32-X2359 Option/uto Switch Mounting imensions Shim uto Switch Mounting Height -P3l ø22 through x ø4.3 through uto Switch Mounting racket Part No./Mounting Method 32 + Shim thickness escription Plate thickness (mm) Part no. Shim 1 KQ MN Shim 0.5 KQ MN LO type Shim mounting position (Up to 3 mm) fixing bolt ( ) Shim mounting position (Up to 3 mm) Shim thickness HIGH type fixing bolt ( ) pplicable auto switch uto switch mounting bracket part no. uto switch mounting bracket fitting parts lineup/eight uto switch mounting surfaces Mounting of auto switch -P3l KU ZL-R Hexagon socket head cap screw (M2.5 x 9 L) uto switch mounting bracket eight: 4 g ithout lock Surfaces with auto switch mounting slot ith lock 1.The hexagon socket head cap screw attached to the auto switch is not required. Turn to loosen and remove. * This procedure is only for auto switches that are ordered separately. Hexagon socket head cap screws are removed when auto switches are shipped together with cylinder. 2.Fix the auto switch and the auto switch mounting bracket with the hexagon socket head cap screw (M2.5 x 9 L) shipped together with the auto switch mounting bracket. 3.heck the detecting position of the auto switch by sliding it along the cylinder tube rib, before fixing the auto switch on the cylinder tube threaded portion by inserting the hexagon socket head cap screw (M2.5 x 9 L) into the long hole of the auto switch mounting bracket. Note) The tightening torque for the hexagon socket head cap screw (M2.5 x 9 L) is 0.2 to 0.3 N m. Shims can be mounted up to 3 mm. However, when mounting 2 mm or more shims, use the below guide pin fixing long bolt instead of a guide pin fixing bolt (marked with ). escription Part no. Note fixing long bolt olt size M4 x 12 L For auto switches, when the total thickness of shims and a workpiece is over 2 mm, the auto switch may not be adjusted to the most sensitive position. Hexagon socket head cap screw (Shipped together with auto switch) (M2.5 x 9 L) Long hole of auto switch mounting bracket ylinder tube rib Hexagon socket head cap screw attached to auto switch (Not required) uto switch mounting bracket kihabara UX 15F, , Sotokanda, hiyoda-ku, Tokyo , JPN Phone: Fax: SM orporation ll Rights Reserved Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. -G Printing RS 8600SZ Printed in Japan.