High Performance Repairable Pneumatic Cylinder Parker Hannifin Corporation

Transcription

1 High Performance Repairable Pneumatic Cylinder 219 Pneumatic ivision

2 eatures Optional Piston Magnet Located under wear band, piston magnet is used for through-thebarrel sensors for electronic piston position indication. oes not add length to the piston. Z-Profile Piston Seal ynamic nitrile piston seal features two rounded micro sealing edges for maximum wear compensation and rounded grooves for retaining lubrication. ual lipseal for 40mm to 100mm bore sizes. luminum Piston with Ultra- Wide Nylon Wear Band Piston is permanently sealed and locked to rod with anaerobic adhesive. Ultra wide wear band prevents metal-to-metal contact and distributes piston loads across wide bearing area. djustable Cushion Option vailable for high speed applications, it features fine-thread, brass needle valves with a captive design. High Strength Bearing PTE-coated bronze rod bearing is inboard of rod seal. Long rod bearing provides rigid support of piston while minimizing bearing stress. Ports Optional NPT or BSPT ports provide full air flow to piston. Rounded Lip Wiper Seal Non-lube, urethane rod seal provides dual function as rod seal and rod wiper to eliminate leakage and prevent contamination from entering the cylinder. Bumpers Impact resistant urethane bumpers are standard for all bore sizes to provide noise reduction and impact resistance our Standard Piston Ends Inch or metric with male or female to meet a variety of requirements. Piston Ground, polished hard chrome plated steel piston rod. Stainless steel is standard on 20 and 25mm bore. Smooth rod surface finish provides minimum friction and maximum seal life. Tapped Mounting Holes Inch or metric holes provide flush mounting from the head or cap face. Standard mounting kits can be bolted-on for adapting to a wide range of applications. Cylinder Body Smooth anodized aluminum tube provides wear-resistant surface. Clean tubular design eliminates area where contamination can accumulate. ed End Cap Construction Precision-machined, aluminum alloy end caps are black anodized and removable from either end for easy cylinder repair. Construction minimizes cylinder size and weight. 220 Pneumatic ivision

3 Ordering Information P1L N 032 M N 0200 W B N N N N M Construction 1 Inch Mounting s Metric Mounting s s 020, 025, 032, 040, 050, 063, 080, 100 N S Material Carbon Steel (std on mm bores) Stainless (std on 20-25mm bores) K N unction ouble cting, Single ouble cting, ouble Cushions/Magnetic Piston No Cushion, No Magnetic Piston M No Cushion, Magnetic Piston 2 Y Cushioned Both Ends, No Magnetic Piston Cushioned Both Ends, Magnetic Piston 2 End Style 1 N Inch Male 4 6 Metric emale 5 Metric Male 5 9 Inch emale 3 Special Port Type 1 N NPT s 4 B BSPT s 5 N T Seal Material Standard Seals luorocarbon Stroke Specify in mm ersion 3 B Basic W With Options / Special N J H B G E Mounting Style No Mountings itted (Std.) ront lange Rear lange Single Rear Clevis ouble Rear Clevis oot, ront & Rear Nose Mount ront Trunnion Rear Trunnion Minimum and Maximum Stroke Length for Standard P1L Cylinders Min. Stroke Max. Stroke Notes: 1 When selecting inch or metric construction, be advised that the piston rod end and porting thread will coincide with the mounting thread selected as the standard for the basic cylinder. or example, selecting M in the construction field will automatically provide a metric male piston rod end and BSPT ports as standard. 2 Not available with fluorocarbon seal option. 3 If cylinder contains no options, then use B as the last digit in the model code. The last 4 boxes are used only when W or / appears in this field. 4 Standard with Inch Construction 5 Standard with Metric Construction 6 Please consult factory for availability of stroke lengths longer than those listed. or sensor part numbers and specifications, see the Electronic Sensors Section. 221 Pneumatic ivision

4 General Specifications Specifications Sizes: 20 to 100mm (3/4" to 4") iameters: 8 to 32mm (5/16" to 1-1/4") Ends: our Standard, specials to order Bumpers standard on both ends djustable Cushions provided at both ends as an option Single End or ouble End Mounting Mounting Styles: 9 standard Rated ir Pressure: 10 bar (145 psi) Non-Lube Strokes available in any practical stroke length Standard Temperature: -23 C to + 74 C (- 10 to ) Optional High Temp Service: -23 C to +121 C (-10 to +250 )* * Option intended for limited exposure to temperatures over +80 C or This option is primarily for applications which subject the cylinder to fluids that have an adverse effect on external seals. Cylinder Weights Base (Lb) Per 25mm of Stroke (Lb) vailable Mountings STYLE N Basic No Mounts STYLE B Single Rear Clevis STYLE ouble Rear Clevis STYLE oot Mount STYLE J ront lange STYLE H Rear lange STYLE E ront Trunnion STYLE Rear Trunnion STYLE G Nose Mount 222 Pneumatic ivision

5 Technical Information Theoretical Push and Pull orces in lbs. mm iameter mm ction Effective rea in 2 Operating Pressure (PSI) Extend Retract Extend Retract Extend Retract Extend Retract Extend Retract Extend Retract Extend Retract Extend Retract Cushioning Capacity Charts Use the graphs below to determine whether a cylinder will adequately decelerate a load without damage to the cylinder. ind the point on the graph where the piston rod speed intersects the weight of the load. ny cylinder bore size above the intersect point will adequately decelerate the load at that speed. v e l o c i t y mm through 40 mm s v e l o c i t y mm through 100 mm s P S 2 P S Weight (lb) Weight (lb) Note: Cushions are recommended for applications with cylinder velocities exceeding 1 ft/sec. 223 Pneumatic ivision

6 Basic No Mount imensions Style N Basic No Mount Typical 20 to 100 mm without air cushion THRE x BG P (8) PLCES Y ZB+STROKE PORT (2) PLCES LB+STROKE P+STROKE R R N With adjustable air cushion - 20 to 25 mm bores GC G G G GB GH With adjustable air cushion - 32 to 100 mm bores (feature a flush-fit cushion adjustment screw) GC G End etails MLE THRES Inch Male - Style N Metric Male - Style 5 L EMLE THRES Inch emale - Style 9 Metric emale - Style 6 N N WRENCH LTS SPECIL RO EN THRES WRENCH LTS Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. 224 Pneumatic ivision

7 Basic No Mount imensions Metric imensions Envelope and Mounting imensions BG (epth) Style 5 Style 6 L Ø MM ia. N N R Y M4x /8* M8 x 1.25 M5 x M5x /8* M10 x 1.25 M6 x M5x /8 M10 x 1.25 M8 x M6x /8 M14 x 1.5 M8 x M8x /4 M18 x 1.5 M10 x M10x /4 M18 x 1.5 M10 x M10x /8 M22 x 1.5 M16 x M12x /2 M26 x 1.5 M20 x *Ports are M5 for cushioned versions dd Stroke LB P ZB G GB G Hex djustable ir Cushion GC G GH Cushion Length /2 25-1/ M5 x /2 20-1/2 23 M5 x /2 30-1/2 1/ /2 22-1/2 1/ /2 23-1/2 1/ /2 20-1/2 1/ /2 25-1/2 3/ /2 25-1/2 1/2 15 Inch imensions Envelope and Mounting imensions (inch) Size BG (epth) (NPT) Style N Style 9 L ia. N N R Y /8 1/4-28 # /8 5/ / /8 7/ / / /8 7/ / / /4 1/2-20 1/ / /4 1/2-20 1/ / /8 3/4-16 5/ / / / Ports are for cushioned versions dd Stroke LB P ZB G GB G Hex djustable ir Cushion GC G GH Cushion Length /2 25-1/ UN /2 20-1/ UN /2 30-1/2 1/8 NPT /2 22-1/2 1/8 NPT /2 23-1/2 1/4 NPT /2 20-1/2 1/4 NPT /2 25-1/2 3/8 NPT /2 25-1/2 1/2 NPT Pneumatic ivision

8 Single Rear Clevis imensions Style B Single Rear Clevis Typical 20 to 100 mm XC+STROKE LB+STROKE Y PORT (2) PLCES P+STROKE G L M ØC (PIN O..) CE ØSB HOLE CT CH CM CY CW CN CX ZX + STROKE CZ Mounting Bracket Note: Mating Mounting Bracket and Pin must be ordered as separate items End etails MLE THRES Inch Male - Style N Metric Male - Style 5 EMLE THRES Inch emale - Style 9 Metric emale - Style 6 L N N WRENCH LTS WRENCH LTS SPECIL RO EN THRES Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. 226 Pneumatic ivision

9 Single Rear Clevis imensions Metric imensions Envelope and Mounting imensions ØC h9 (BSPT) G Style 5 Style 6 L L M ia. N Y /8* 7 M8 x 1.25 M5 x /8* 8 M10 x 1.25 M6 x / M10 x 1.25 M8 x /8 10 M14 x 1.5 M8 x /4 12 M18 x 1.5 M10 x /4 13 M18 x 1.5 M10 x /8 15 M22 x 1.5 M16 x /2 17 M26 x 1.5 M20 x CE CH CM CN CT CW CX CY CZ ØSB dd Stroke LB P XC ZX * Ports are M5 for cushioned versions Inch imensions Envelope and Mounting imensions (inch) ØC (NTP) G Style N Style 9 L L M ia. N Y / /4-28 # / / / / / / / / / / /2-20 1/ / /2-20 1/ / /4-16 5/ / / CE CH CM CN CT CW CX CY CZ ØSB dd Stroke LB P XC ZX Ports are for cushioned versions 227 Pneumatic ivision

10 ouble Rear Clevis imensions Style ouble Rear Clevis Typical 20 to 63 mm LB+STROKE Y PORT (2) PLCES P+STROKE L RR ØC (PIN O..) CZ C CB CB Style ouble Rear Clevis Typical 80 to 100 mm TX T TZ Mounting Bracket LB+STROKE Y P+STROKE L RR TZ CZ C TH TE TH TE XC+STROKE Z+STROKE TY TW ØSB HOLE (4) PLCES PORT (2) PLCES ØC (PIN O..) CB XC+STROKE Z+STROKE TY TW CX TX T ØSB HOLE (4) PLCES Note: Mating Mounting Bracket and Pin must be ordered as separate items. Mounting Bracket End etails MLE THRES Inch Male - Style N Metric Male - Style 5 L EMLE THRES Inch emale - Style 9 Metric emale - Style 6 SPECIL RO EN THRES Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. N WRENCH LTS N WRENCH LTS 228 Pneumatic ivision

11 ouble Rear Clevis imensions Metric imensions Envelope and Mounting imensions C CB ØC d 9 CZ CX (BSPT) Style 5 Style 6 L L ia. N RR /8* M8x1.25 M5x /8* M10x1.25 M6x /8 M10x1.25 M8x /8 M14x1.5 M8x /4 M18x1.5 M10x /4 M18x1.5 M10x /8 M22x1.5 M16x /2 M26x1.5 M20x Ø SB TY T TE TH TX TW TZ Y dd Stroke LB P XC Z * Ports are M5 for cushioned versions Inch imensions Envelope and Mounting imensions (inch) C CB ØC CZ CX (NPT) Style N Style 9 L L Ø MM N RR /8 1/4-28 # /8 5/ / /8 7/ / /8 7/ / /4 1/2-20 1/ /4 1/2-20 1/ /8 3/4-16 5/ / / ØSB TY T TE TH TX TW TZ Y dd Stroke LB P XC Z Ports are for cushioned versions 229 Pneumatic ivision

12 oot Mount imensions Style oot Mount Typical 20 to 100 mm LB+STROKE G Y P+STROKE PORT (2) PLCES T E H ØSB SLOT T U SW SU SS+STROKE SU SW End etails MLE THRES Inch Male - Style N Metric Male - Style 5 EMLE THRES Inch emale - Style 9 Metric emale - Style 6 L N N WRENCH LTS WRENCH LTS SPECIL RO EN THRES Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. 230 Pneumatic ivision

13 oot Mount imensions Metric imensions Envelope and Mounting imensions E H T (BSPT) G Style 5 Style /8* 6 M8x1.25 M5x /8* 6.5 M10x1.25 M6x /8 6.5 M10x1.25 M8x /8 7 M14x1.5 M8x /4 11 M18x1.5 M10x /4 12 M18x1.5 M10x /8 12 M22x1.5 M16x /2 13 M26x1.5 M20x L ia. N ØSB SU SW T U Y dd Stroke LB P SS * Ports are M5 for cushioned versions Inch imensions Envelope and Mounting imensions (inch) E H T Ø E (NPT) G Style N Style 9 L N ØSB / /4-28 # / / / / / / / / / / /2-20 1/ / /2-20 1/ / /4-16 5/ / / SU SW T U Y dd Stroke LB P SS Ports are for cushioned versions 231 Pneumatic ivision

14 ront lange imensions Style J ront lange Typical 20 to 100 mm ØB HOLE (4) PLCES Y ZB+STROKE LB+STROKE P+STROKE PORT (2) PLCES T U T U W End etails MLE THRES Inch Male - Style N Metric Male - Style 5 EMLE THRES Inch emale - Style 9 Metric emale - Style 6 L N N WRENCH LTS WRENCH LTS SPECIL RO EN THRES Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. 232 Pneumatic ivision

15 ront lange imensions Metric imensions Envelope and Mounting imensions (BSPT) ØB Style 5 Style 6 L ia. N T U W Y /8* M8x1.25 M5x /8* M10x1.25 M6x /8 7 7 M10x1.25 M8x /8 8 7 M14x1.5 M8x /4 9 9 M18x1.5 M10x / M18x1.5 M10x / M22x1.5 M16x / M26x1.5 M20x dd Stroke LB P ZB * Ports are M5 for cushioned versions Inch imensions Envelope and Mounting imensions (inch) (NPT) ØB Style N Style 9 L ia. N T U W Y / /4-28 # / / / / / / / / / / /2-20 1/ / /2-20 1/ / /4-16 5/ / / dd Stroke LB P ZB Ports are for cushioned versions 233 Pneumatic ivision

16 Rear lange imensions Style H Rear lange Typical 20 to 100 mm Y Z+STROKE LB+STROKE P+STROKE ØB HOLE (4) PLCES PORT (2) PLCES T U T U End etails MLE THRES Inch Male - Style N Metric Male - Style 5 EMLE THRES Inch emale - Style 9 Metric emale - Style 6 L N N WRENCH LTS WRENCH LTS SPECIL RO EN THRES Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. 234 Pneumatic ivision

17 Rear lange imensions Metric imensions Envelope and Mounting imensions (BSPT) ØB Style 5 Style 6 L ia. N T U Y /8* M8x1.25 M5x /8* M10x1.25 M6x /8 7 7 M10x1.25 M8x /8 8 7 M14x1.5 M8x /4 9 9 M18x1.5 M10x / M18x1.5 M10x / M22x1.5 M16x / M26x1.5 M20x dd Stroke LB P Z * Ports are M5 for cushioned versions Inch imensions Envelope and Mounting imensions (inch) dd Stroke LB P Z (NPT) ØB Style N Style 9 L ia. N T U Y / /4-28 # / / / / / / / / / / /2-20 1/ / /2-20 1/ / /4-16 5/ / / Ports are for cushioned versions 235 Pneumatic ivision

18 ront Trunnion imensions Style E ront Trunnion Typical 20 to 63 mm ZB+STROKE BT THRE (2) PLCES UT TS* *TTCHMENT MOUNTING LIMITS Y PORT (2) PLCES LB+STROKE P+STROKE TC ØT (PIN O..) (2) PLCES TE TT TX T ØSB HOLE (4) PLCES XG TY TW Trunnion Bracket Note: Trunnion Bracket must be ordered as separate item End etails MLE THRES Inch Male - Style N Metric Male - Style 5 EMLE THRES Inch emale - Style 9 Metric emale - Style 6 L N N WRENCH LTS WRENCH LTS SPECIL RO EN THRES Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. 236 Pneumatic ivision

19 ront Trunnion imensions Metric imensions Envelope and Mounting imensions BT (BSPT) Style 5 Style 6 L ia. N XG Y ØSB M5x /8* M8x1.25 M5x M6x /8* M10x1.25 M6x M8x /8 M10x1.25 M8x M10x /8 M14x1.5 M8x M12x /4 M18x1.5 M10x M14x /4 M18x1.5 M10x TC ØT e8 TE TS TT T TW TX TY UT dd Stroke LB P ZB * Ports are M5 for cushioned versions Inch imensions Envelope and Mounting imensions (inch) BT (NPT) Style N Style 9 L ia. N XG Y ØSB M5x /8 1/4-28 # M6x /8 5/ / M8x /8 7/ / M10x /8 7/ / M12x /4 1/2-20 1/ M14x /4 1/2-20 1/ TC ØT TE TS TT T TW TX TY UT dd Stroke LB P ZB Ports are for cushioned versions 237 Pneumatic ivision

20 Rear Trunnion imensions Style Rear Trunnion Typical 20 to 63 mm ZB+STROKE Y PORT (2) PLCES LB+STROKE P+STROKE BT THRE (2) PLCES UT TS* *TTCHMENT MOUNTING LIMITS TE TC ØT (PIN O..) (2) PLCES XJ+STROKE Z+STROKE TY TW ØSB HOLE (4) PLCES TT TX T Trunnion Bracket Note: Trunnion Bracket must be ordered as separate item End etails MLE THRES Inch Male - Style N Metric Male - Style 5 EMLE THRES Inch emale - Style 9 Metric emale - Style 6 L N N WRENCH LTS WRENCH LTS SPECIL RO EN THRES Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. 238 Pneumatic ivision

21 Rear Trunnion imensions Metric imensions Envelope and Mounting imensions BT (BSPT) Style 5 Style 6 L ia. N Y ØSB TC M5x /8* M8x1.25 M5x M6x /8* M10x1.25 M6x M8x /8 M10x1.25 M8x M10x /8 M14x1.5 M8x M12x /4 M18x1.5 M10x M14x /4 M18x1.5 M10x ØT e8 TE TS TT T TW TX TY UT dd Stroke LB P XJ ZB Z *Ports are M5 for cushioned versions Inch imensions Envelope and Mounting imensions (inch) BT (NPT) Style N Style 9 L ia. N Y ØSB TC M5x /8 1/4-28 # M6x /8 5/ / M8x /8 7/ / M10x /8 7/ / M12x /4 1/2-20 1/ M14x /4 1/2-20 1/ ØT dd Stroke TE TS TT T TW TX TY UT LB P XJ ZB Z Ports are for cushioned versions 239 Pneumatic ivision

22 Nose Mount imensions Style G Nose Mount Typical 20 to 25 mm ZB 1 +STROKE LB 1 +STROKE Y P 1 +STROKE PORT (2) PLCES B WT L N N N NN THRES N Metric imensions Envelope and Mounting imensions BN (BSPT) Style 5 Style 6 L ia. NN N B WT Y dd Stroke LB 1 P 1 ZB /8* M8x1.25 M5x / /8* M10x1.25 M6x / * Ports are M5 for cushioned versions Inch imensions Envelope and Mounting imensions (inch) BN (NPT) Style N Style 9 L ia. NN N B WT Y dd Stroke LB 1 P 1 ZB /8 1/4-28 # / /8 5/ / / Ports are for cushioned versions End etails 20 and 25 mm MLE THRES Inch Male - Style N Metric Male - Style 5 EMLE THRES Inch emale - Style 9 Metric emale - Style 6 WRENCH LTS WRENCH LTS SPECIL RO EN THRES Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. 240 Pneumatic ivision

23 Nose Mount imensions Style G Nose Mount Typical 32 to 63mm Y 1 ZB +STROKE 1 LB +STROKE 1 P +STROKE W PORT (2) PLCES R N N R N NN THRE Metric imensions Envelope and Mounting imensions Inch imensions Envelope and Mounting imensions (inch) BN -0.8 BN * (BSPT) * (NPT) Style 5 Style N Style 6 Style 9 WT L L ia. ia. NN N N R B W WT Y NN N N R B W WT Y B dd Stroke LB 1 P 1 ZB /8 9 M10x1.25 M8x / /8 14 M14x1.5 M8x /4 15 M18x1.5 M10x / /4 16 M18x1.5 M10x / * See Inch imensions for NPT Port Size. dd Stroke LB 1 P 1 ZB / / / / / / / / /2-20 1/ / / /2-20 1/ / * See Metric imensions for BSPT Port Size. End etails 32 and 63 mm MLE THRES Inch Male - Style N Metric Male - Style 5 EMLE THRES Inch emale - Style 9 Metric emale - Style 6 L W W N N N N SPECIL RO EN THRES WRENCH LTS WRENCH LTS Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or (Note: L = L+ and = W+). If otherwise special, supply a dimensioned sketch. 241 Pneumatic ivision

24 ouble imensions ouble- Typical 20 to 100 mm ZM+ (2 x STROKE) LG+STROKE Y PK+STROKE PORT (2) PLCES R R R N ouble- Nose Mount (32-63mm bore) 1 ZM + (2 x STROKE) 1 LG +STROKE 1 Y 1 PK +STROKE W PORT (2) PLCES R N or detailed dimensions for the nose mount from 20 to 63 mm bore, please refer to pages 78 and End etails MLE THRES Inch Male - Style N Metric Male - Style 5 L EMLE THRES Inch emale - Style 9 Metric emale - Style 6 N N WRENCH LTS WRENCH LTS SPECIL RO EN THRES Style 3 Special Metric or Inch threads, extension, blank, etc., are also available. To order, specify Style 3 and give desired dimensions for or, and L or. If otherwise special, supply a dimensioned sketch. When two rod ends are different on double rod cylinder, please clearly indicate what rod end should be provided on which end of the cylinder, or provide a sketch. 242 Pneumatic ivision

25 ouble imensions Metric imensions Envelope and Mounting imensions (BSPT) Style 5 Style 6 L ia. N N R W /8* M8x1.25 M5x /8* M10x1.25 M6x /8 M10x1.25 M8x /8 M14x1.5 M8x /4 M18x1.5 M10x /4 M18x 1.5 M10x /8 M22 x1.5 M16x /2 M26x1.5 M20x Y Y 1 dd Stroke LG LG 1 PK PK 1 ZM ZM * Ports are M5 for cushioned versions INCH IMENSIONS - Envelope and Mounting imensions (inch) (NPT) Style N Style 9 Y Y 1 dd Stroke LG LG 1 PK PK 1 ZM ZM L ia. N N R W /8 1/4-28 # /8 5/ / /8 7/ / /8 7/ / /4 1/2-20 1/ /4 1/2-20 1/ /8 3/4-16 5/ / / Ports are for cushioned versions 243 Pneumatic ivision

26 Mounting Brackets Single Clevis Brackets K H ØC (PIN O..) ØG B N L M C Single Clevis Pin CZ CL C Note : Two snap rings shown are included with the pivot pin. Order clevis bracket separately. Single Clevis Kit ssembly Instructions lign the rear clevis with the port location as desired. Insert the four (4) screws through the bracket and thread them into the end caps until they are hand tight. Torque the screws to the values listed in the table below. Single Clevis Kit, bracket and pivot pin are ordered separately. Please see next page for part numbers. astener Size Torque M4x in-lbs Nm M5x in-lbs Nm M5x in-lbs Nm 40 1/4-28 M6x in-lbs Nm 50 5/16-24 M8x in-lbs Nm 63 3/8-24 M10x ft-lbs Nm 80 3/8-24 M10x ft-lbs Nm 100 1/2-20 M12x ft-lbs Nm 244 Pneumatic ivision

27 Mounting Brackets Single Clevis Brackets Metric imensions Part Number B C ØC h9 ØG H K L M N L L L L L L L L Imperial imensions (Inch) Part Number B C ØC ØG H K L M N L L L L L L L L Single Clevis Pins Metric imensions Part Number Part Number ØC h9 ØC CL CL CZ L L L L L L L L Imperial imensions (Inch) CZ L L L L L L L L Pneumatic ivision

28 Mounting Brackets ouble Clevis Brackets mm ouble Clevis Bracket mm ouble Clevis Bracket TR ØTS TB TE TW TR ØTS T T TH T ØTM Holes 4 Places TH TG TG T TW ØTM x 4 TC T TW T TB ouble Clevis Pin CZ CL C Note: Two snap rings shown are included with the pivot pin. Order clevis bracket separately. ouble Clevis mm ouble Clevis mm ouble Clevis Kit ssembly Instructions lign the rear clevis with the port location as desired. Insert the four (4) screws through the bracket and thread them into the end caps until they are hand tight. Torque the screws to the values listed in the table beside. ouble Clevis Kit, bracket and pivot pin are ordered separately. Please see next page for part numbers. astener Size Torque M4x in-lbs Nm M5x in-lbs Nm M5x in-lbs Nm 40 1/4-28 M6x in-lbs Nm 50 5/16-24 M8x in-lbs Nm 63 3/8-24 M10x ft-lbs Nm 80 3/8-24 M10x ft-lbs Nm 100 1/2-20 M12x ft-lbs Nm 246 Pneumatic ivision

29 Mounting Brackets ouble Clevis Brackets Metric imensions Part Number T TB TC T TE T TG TH TM TR TS 49 TW L L L L L L L L Imperial imensions (Inch) Part Number T TB TC T TE T TG TH TM TR TS.002, -0 L L L L L L L L TW ouble Clevis Pins Metric imensions Part Number ØC d9 CL CZ L L L L L L L L Imperial imensions (Inch) Part Number ØC CL CZ L L L L L L L L Pneumatic ivision

30 Mounting Kits ront or Rear lange Mount Kit ØB Hole (4) Places T U Metric imensions T U Part Number B U T L L L L L L L L Imperial imensions (Inch) Part Number B U T L L L L L L L L lange Mount Kit Installation Instructions Insert the four (4) screws through the nose mount or the flange mounts and thread them into the cylinder head or cap until they are hand tight. Torque the screws to the values listed in the table below. The lange Mounting Bracket Kit includes 4 Bolts Size astener Size Torque M4x in-lbs Nm M5x in-lbs Nm M5x in-lbs Nm 40 1/4-28 M6x in-lbs Nm 50 5/16-24 M8x in-lbs Nm 63 3/8-24 M10x ft-lbs Nm 80 3/8-24 M10x ft-lbs Nm 100 1/2-20 M12x ft-lbs Nm 248 Pneumatic ivision

31 Mounting Kits oot Mount Bracket ØCC Hole (4) Places P Hole R ØSB Slot S Metric imensions R T U SW SU Part Number.15-0 ØCC P R S ØSB SU SW T U L L L L L L L L Imperial imensions (inch) Part Number ØCC P R S ØSB SU SW T U L L L L L L L L oot Mount Kit ssembly Instructions lign each of the foot brackets with the port location as desired. Insert the four (4) screws through the foot mounts and thread them into the end caps until they are hand tight. Place the cylinder assembly on to a flat surface and torque the screws to the values listed in the table below. Make sure the foot mounts rest properly on a flat surface. The oot Mount Bracket Kit includes 8 Bolts Size astener Size Torque M4x in-lbs Nm M5x in-lbs Nm M5x in-lbs Nm 40 1/4-28 M6x in-lbs Nm 50 5/16-24 M8x in-lbs Nm 63 3/8-24 M10x ft-lbs Nm 80 3/8-24 M10x ft-lbs Nm 100 1/2-20 M12x ft-lbs Nm 249 Pneumatic ivision

32 Mounting Kits Trunnion Mount Bracket TR ØTS TB TE TW TG TH T Metric imensions T TW ØTM x 4 TC Part Number T TB TC T TE T TG TH TM TR TS H9 TW L L L L L L Imperial imensions (Inch) Part Number T TB TC T TE T TG TH TM TR.002 TS -0 TW L L L L L L Trunnion Mount ssembly Instructions lign the bracket on the machine member providing cylinder rotation as desired. Securely mount the bracket to the machine member. lign the cylinder head or cap with the bracket. Insert the bearing, washer and pivot bolt on to each side of the cylinder as shown. Torque the pivot bolts to the values listed in the table below. Use only bolts provided, as they have a special adhesive coating for secure fastening. Size Trunnion Pivot Bolt Torque 20 M5x in-lbs Nm 25 M6x in-lbs Nm 32 M8x in-lbs Nm 40 M10x ft-lbs Nm 50 M12x ft-lbs Nm 63 M14x ft-lbs Nm Notes Order trunnion mounts by specifying E for front trunnion or for rear trunnion in the Mounting Style digit of the model code. The bearings, washers and pivot bolts will be supplied with the cylinder. The trunnion bracket must be ordered as a separate item, using the part numbers shown above. 250 Pneumatic ivision

33 End ccessories Jam Nut Jam Nut should be ordered separately on all mounting styles B C UN-2B Jam Nut imensions Metric imensions Part Number B C L M8 x 1.25 L M10 x 1.25 L M14 x 1.5 L M18 x 1.5 L M22 x 1.5 L M26 x 1.5 Imperial imensions (inch) Part Number B C Piston Clevis L /4-28 L /16-24 TH' C L /16-20 L /2-20 L /4-16 B L E J K L NUT Piston Clevis imensions Metric imensions Part Number B C E H h9 J K L L M8x L M10x L M10x L M14x L M18x L M18x PIM-4PRC 80 M22x L M26x Imperial imensions (inch) H I. (PIN O..) Part Number B C E H J K L L / L / L / L / L / L / L / L Pneumatic ivision

34 Mounting Kits & ccessories How to Order P1L Mounting Kits as a Separate Item Size oot Mounting lange Inch Metric Inch Metric 20 L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L Size Single Clevis ouble Clevis Single Inch Metric Inch Metric Clevis Pin Notes : Inch mounting kits include inch threaded bolts, while Metric mounting kits include metric threaded bolts. Please verify that the kit style matches the cylinder Construction type (code N or M ) for which it is intended. Clevis pins may be used for either Inch or Metric mounting kits. ouble Clevis Pin 20 L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L Mounting Brackets and End ccessories Size Trunnion/ ouble Clevis Bracket Single Clevis Bracket Piston Clevis Jam Nut Inch Metric Inch Metric 20 L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L PIM-4PRC L L L L L L L L Service Kits Size Single Cylinder Repair Kits ouble Cylinder Repair Kits Consisting of: 1 ea. Symbol #5, 7, 12, & 2 ea. Symbol #1, 8 11, 14 Consisting of: 1 ea. Symbol #5, 7, & 2 ea. Symbol #1, 8 11, 12, 14 Class 1 Seals, Std. Service Class 5 Seals, High Temp. Class 1 Seals, Std. Service Class 5 Seals, High Temp. mm Part No. Part No. Part No. Part No. 20 P1L P1L P1L020K001 P1L020K P1L P1L P1L025K001 P1L025K P1L P1L P1L032K001 P1L032K P1L P1L P1L040K001 P1L040K P1L P1L P1L050K001 P1L050K P1L P1L P1L063K001 P1L063K P1L P1L P1L080K001 P1L080K P1L P1L P1L100K001 P1L100K Pneumatic ivision