Bore ø 32, 40, 50, 63, 80, 100, 125 Ports 32 = 1/8, 40/50 = 1/4, 63/80 = 3/8, 100/125 = 1/2

Save this PDF as:
Size: px
Start display at page:

Download "Bore ø 32, 40, 50, 63, 80, 100, 125 Ports 32 = 1/8, 40/50 = 1/4, 63/80 = 3/8, 100/125 = 1/2"

Transcription

1 6 S E R I E S Cylinders Series 6 Catalog 2006 Single, double acting, magnetic (DIN/ISO 643) Bore: ø 32, 40, 50, 63, 80, 00, 25 cushioned [ /4, 9/6, 2, 2 /2, 3 /8, 4, 5 inch approximations] The Series 6 cylinders with diameters 32, 40, 50, 63, 80, 00 and 25 have been designed to comply with the dimensions laid down in the DIN/ISO 643 standards. The extruded aluminum tube with improved aesthetics, has two grooves (on three sides) where the proximity switch Mod. CST can be directly mounted. This enables the same cylinder dimensions to be retained. Four tie rods located inside of the tube make the mounting of the end blocks extremely secure. This cylinder series is equipped with adjustable end stroke cushioning. Moreover, these cylinders are also equipped with a mechanical cushioning in order to reduce the impact of the piston as it reaches the end of the stroke (only until ø00). The cylinder series can also accommodate stroke lengths up to 000 mm for bore sizes shown in the table. DIN/ISO 643/VDMA High durability Clean design GENERAL DATA Type of construction with tie rods Operation double acting, single acting, other parts see coding Materials aluminum end blocks, other parts see coding Type of mounting with tie rods, front flange, rear flange, feet front and rear trunnion, swivel combination Stroke mm Bore ø 32, 40, 50, 63, 80, 00, 25 Ports 32 = /8, 40/50 = /4, 63/80 = 3/8, 00/25 = /2 Assembly position any position Operating temperature 0 80 C (with dry air 20 C), 32 F 75 F (dry air 4 F) Special designs for applications in damp, dusty or aggressive environments.45 Dimensions are in millimeters, inch notations are approximate for bore sizes.

2 Catalog 2006 S E R I E S 6 PNEUMATIC SPECIFICATIONS Operating pressure Speed Fluid CYLINDER CODING 6M2P = standard version in stock. NOTE: Accessories are not mounted on the cylinders. 0 bar [Min. bar (4.5psi); Max. 0 bar (45 psi)] mm/sec (No load) [Min. 0 mm/sec(no load); Max 000mm/sec (No load)] clean air, lubrication* *if lubricated air is used, it is recommended to use oil ISOVG32. Once applied the lubrication should never be interrupted. SERIES 6 = ø from DIN/ISO 643 OPERATION = single acting (front spring) 2 = double acting (front and rear cushions) 3 = double acting (no cushion) 4 = double acting (rear cushions) 5 = double acting (font cushion) 6 = double acting (double rod with front and rear cushions) 7 = single acting (double rod) VERSIONS M = standard, magnetic 6M2P050A0200 STROKE (see table) BORE 032 mm 040 mm 050 mm 063 mm MATERIALS P = rolled stainless steel rod anodized profile aluminum tube Buna N seals rod seals polyurethane nuts and tie rods zinc plated steel R = rolled stainless steel rod anodized profile aluminum tube Buna N seals rod seals polyurethane nuts and tie rods stainless steel steel 080 mm 00 mm 25 mm TYPE OF BRACKET A = standard lock nut for rod RL = cylinder with rod lock S = special to be indicated V = viton rod seal N = tandem R = Buna N rod seal W = all seals in viton CHARACTERISTICS OF SINGLE ACTING SERIES 60 6 Force in N x = lbf ømm min max stroke Extend N Force of spring at rest Force of compressed spring at 6 bar N (stroke 75 mm) N NOTE : the Series 60 6 single acting cylinders dimensions for L and L2 are to be increased by 25 mm. Dimensions are in millimeters, inch notations are approximate for bore sizes..46

3 6 S E R I E S Catalog 2006 TABLE SHOWING AIR CONSUMPTION OF SERIES 6 ø Cyl. in mm (inch) ø Rod in mm Operating pressure in bar bar = 4.5 psi Working area in cm Air consumption in NL for each 0 mm of stroke 32 ( /4 ) 2 Extend side Retract side ( 9/6 ) 6 Extend side Retract side (2 ) 20 Extend side Retract side (2 /2 ) 20 Extend side Retract side (3 /8 ) 25 Extend side Retract side (4 ) 25 Extend side Retract side (5 ) 32 Extend side Retract side THE VALUES SHOWN IN THE TABLE WERE OBTAINED USING THE FOLLOWING FORMULA: Qs = D 2. π. (P + ) H Qn = (Qs+Qt) n Qt = (D 2 d 2 ). π. (P + ). H Qs = consumption on extend side D = diameter on extend side in cm. Qt = consumption on retract side d = diameter of rod in cm Qn = consumption of cylinder H = cylinder stroke in cm n P = number of cycles per minute = operating pressure in bar TABLE SHOWING THE OUTPUT FORCE OF SERIES 6 ø Cyl. in mm (inch) ø Rod in mm Operating pressure in bar bar = 4.5 psi Working area in cm Output force in N (efficiency factor 0,9) Force in N x lbf 32 ( /4 ) 2 Extend side Retract side ( 9/6 ) 6 Extend side Retract side (2 ) 20 Extend side Retract side (2 /2 ) 20 Extend side Retract side (3 /8 ) 25 Extend side Retract side (4 ) 25 Extend side Retract side (5 ) 32 Extend side Retract side THE VALUES SHOWN IN THE TABLE WERE OBTAINED USING THE FOLLOWING FORMULA: Ss = D 2. π 4. P. η St = (D 2 d 2 ). π 4. P. η Ss = output force on extend side St = output force on retract side P = operating pressure in bar D = diameter on extend side in cm d = diameter of rod in cm η = efficiency factor.47 Dimensions are in millimeters, inch notations are approximate for bore sizes.

4 Catalog 2006 S E R I E S 6 Cylinders Series 6 ø MM KK B d PL L AM VA EE WH L2 ZJ VD N BG RT G TG R E 32 2 M0x, G/ M6 5 32, M2x, G/ M , M6x, G/ ,5 6 M8 8 46,5 6 64, M6x, G3/ ,5 6 M8 8 56, M20x, G3/ M M20x, G/ ,5 9,5 M M27x , G/ M2 0, N.B. : the single-acting cylinders sizes L nd L2 are increased by 25 mm. SW SW2 SW3 Cushion stroke Cylinders Series 6 Double-rod + two times ø MM KK B d PL L AM EE WH L2 ZM VD N RT BG G TG R E 32 2 M0x, G/ M , M2x, G/ M , M6x, G/ ,5 M ,5 6 64, M6x, G3/ ,5 M , M20x, G3/ M M20x, G/ ,5 M0 9, M27x , G/ M2 23 0, N.B. : the single-acting cylinders sizes L nd L2 are increased by 25 mm. SW SW2 SW3 Cushion stroke Dimensions are in millimeters, inch notations are approximate for bore sizes..48

5 6 S E R I E S Catalog 2006 Cylinders Series 6 tandem ø EE L2 L3 32 G/8 7,5 97,5 40 G/4 9,5 22,5 50 G/ G3/ G3/8 225,5 27,5 00 G/ G/ Cylinders Series 6 with rod lock ø L L2 L3 L4 L5 L6 L7 L8 L9 L0 ØD ød d ød2 ød3 f8 A ±0.5 G H H M Z , , ,5 M5 25,5 46,5 M6 M6x , G/ M6 M6x , ,5 G/ M8 M6x ,5 49, ,5 G/ M8 M8x G/ M0 M0x G/8 58 0,5 M0 M0x , G/ M2 M2x40.49 Dimensions are in millimeters, inch notations are approximate for bore sizes.

6 Catalog 2006 S E R I E S 6 Foot mount Mod. B... Material: zinc-plated steel. N 2 feet Mod. ø AT SA ±.25 XA ±.25 TR JS 4 E AB AH JS 6 AO AU Torque force (max.) B Nm B , Nm B , Nm B Nm B Nm B ,5 4, Nm B , Nm Front and rear flange Mod. D-E... N flange Mod. ø W ±2 MF ZB JS 4 TF JS 4 R JS 4 UF E FB H 3 ZF ±.25 Torque force (max.) D-E Nm D-E Nm D-E Nm D-E Nm D-E Nm D-E Nm D-E Nm Dimensions are in millimeters, inch notations are approximate for bore sizes..50

7 6 S E R I E S Catalog 2006 Rear trunnion, female Mod. C... and CH... N female trunnion Mod. ø CD H9 L FL XD ±,6 MR E CB H4 UB h4 Torque force (max.) C Nm C Nm C Nm C Nm C-H Nm C-H Nm C-H Nm Front trunnion, female Mod. H... and C-H... N female trunnion Mod. ø CD H9 E H D MR F G CB H4 UB h4 H , H H , H , C-H C-H C-H Dimensions are in millimeters, inch notations are approximate for bore sizes.

8 Catalog 2006 S E R I E S 6 Rear trunnion, male Mod. L... N male trunnion Mod. ø CD H9 L FL XD ±,6 MR E EW Torque force (max.) L Nm L Nm L Nm L Nm L Nm L Nm L Nm Centre trunnion Mod. F... Material: zinc-plated brass. N centre trunnion N 4 fixing elements Mod. ø XV ±2 XV ±2 XV2 ±2 TM h4 TK TD e9 TL h4 UW R F , F , ,5 F , , ,5 F , ,5 F ,5 0 25, ,5 F , , ,2 F ,2 Dimensions are in millimeters, inch notations are approximate for bore sizes..52

9 6 S E R I E S Catalog 2006 Accessory combination Mod. C+L+S ø CD H9 L FL XD ±,6 TG E I M N Torque force (max.) , ,5 6Nm ,5 6Nm , Nm , Nm Nm Nm Nm 90 male trunnion Mod. ZC... The following is supplied : N support Mod. ø EB H3 CK H9 HB H3 XD TE JS4 UL MAX EA MAX GL JS4 L5 MAX RA JS4 EM ZC , , ZC , , ZC , ZC , , ZC , ZC , ZC , UR JS4 PH JS5 BT BR MAX P -0, P -0, P P P -0, P -, ,5 P.53 Dimensions are in millimeters, inch notations are approximate for bore sizes.

10 Catalog 2006 S E R I E S 6 Trunnion ball- joint Mod. R*... *not according to standard. N trunnion ball joint Mod. ø CX L DL XN ±,6 MS E EX -0. Z Torque force (max.) R Nm R Nm R Nm R Nm R Nm R Nm Counter bracket for centre trunnion Mod. BF... N 2 supports Mod. ø CR NH C b3 TH UL FK FN B B2 HB BF , ,8 6,6 BF BF BF ,5 3, Dimensions are in millimeters, inch notations are approximate for bore sizes..54

11 6 S E R I E S Catalog 2006 Assembly The horizontal mounting foot allows the connection between the valve or the solenoid valve and the cylinder, forming a compact pneumatic working unit, which is easy to apply. Mod. PCV-6-K3 to connect valves-solenoid valves Series 3 PCV-6-K4 to connect valves-solenoid valves Series 4 port G/4 PCV-6-KE to connect valves-solenoid valves Series E PCV-6-K8 to connect valves-solenoid valves Series 4 port G/8 Rod Fork End Mod. G... ISO 840. Material: zinc-plated steel. Mod. ø øck LE CM CL ER CE KK B øb G M0x, G M2x, G M6x, G M20x, G M27x Swivel Ball Joint Mod. GA... ISO 839. Material: zinc-plated steel. Mod ø øcn H7 U EN ER AX CE KK øt Z SW GA , M0x,25 5 6,5 7 GA M2x,25 7,5 6,5 9 GA M6x,5 22 7,5 22 GA M20x,5 27, GA M27x2 40 7, Dimensions are in millimeters, inch notations are approximate for bore sizes.

12 Catalog 2006 S E R I E S 6 Piston Rod Socket Joint Mod. GY... Material: zama and zinc-plated steel. Mod. ø KK L CE L2 AX SW SW L L3 øt ød E øb øc Z GY M0x, , , GY M2x, , , GY M6x, , GY M20x, , , ,5 Clevis Pin Mod. S... N clevis pin (stainless steel 303) N 2 Seeger (steel) Piston Rod Lock Nut Mod. U... UNI EN ISO Material: zinc-plated steel. Included on all Series 6 cylinders. Mod. ø d L L L2 H3 L3 S , 3 S , 3 S , 3 S , 3 S , 3 S ,3 5 S ,5 32,3 4,25 Mod. ø D m SW U M0x, U M2x, U M6x, U M20x, U M27x2 2 4 Dimensions are in millimeters, inch notations are approximate for bore sizes..56

Cylinders Series 61 - Aluminium profile

Cylinders Series 61 - Aluminium profile CATALOGUE > Release 8. Cylinders Series 6 - Aluminium profile MOVEMENT > Cylinders Series 6 Single, double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00, 25 (ISO 5552)» ISO 5552 (corresponding to

More information

Aluminium profile. TANDEM: Double thrust and traction forces. LOW FRICTION: Friction force reduced by over 40%

Aluminium profile. TANDEM: Double thrust and traction forces. LOW FRICTION: Friction force reduced by over 40% CATALOGUE > Release 8.7 > Series 6 cylinders Series 6 cylinders - Aluminium profile Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40,

More information

Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 100, 125mm

Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 100, 125mm CATALOGUE > Release 8.8 > Series 60 cylinders Series 60 cylinders Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 00, 25mm»»

More information

Aluminium tube and profile

Aluminium tube and profile > Series 63 cylinders CATALOGUE > 206 Series 63 cylinders - Aluminium tube and profile New Single and double-acting, magnetic, cushioned Versions: standard, low friction, high and low temperatures ø 32,

More information

Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 100, 125mm

Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 100, 125mm CATALOGUE > Release 8.6 > Series 60 cylinders Series 60 cylinders New version Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 00,

More information

Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm

Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm > Series 62 cylinders CATALOGUE > Release 8.6 Series 62 cylinders - Aluminium profile Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 5552 standards and with the

More information

Extruded Body Cylinders, ISO 6431, ISO compliant Series 61

Extruded Body Cylinders, ISO 6431, ISO compliant Series 61 1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Extruded Body Cylinders, ISO 6431, ISO 15552 compliant Series 61 Single or double-acting, magnetic, cushioned Standard and

More information

Aluminium profile. Double-acting, cushioned, magnetic ø mm

Aluminium profile. Double-acting, cushioned, magnetic ø mm > Series 4 cylinders Series 4 cylinders - Aluminium profile Double-acting, cushioned, magnetic ø 60-200 mm»» In compliance with ISO 643/ VDMA 24562 standards»» Rolled stainless steel rod»» Adjustable pneumatic

More information

Series 6PF Positioning Feedback cylinders 1/ Double-acting low friction, magnetic ø 50, 63, 80, 100, 125 mm

Series 6PF Positioning Feedback cylinders 1/ Double-acting low friction, magnetic ø 50, 63, 80, 100, 125 mm CATALOGUE > Release 8.8 > Series 6PF cylinders Series 6PF Positioning Feedback cylinders Double-acting low friction, magnetic ø 50, 63, 80, 00, 25 mm»» In compliance with ISO 5552 standards and with the

More information

Tie-rod Cylinders, ISO 6431, ISO compliant Series 60

Tie-rod Cylinders, ISO 6431, ISO compliant Series 60 Tie-rod Cylinders, ISO 6431, ISO 15552 compliant Series 60 Single or double-acting, magnetic, cushioned Standard and low friction versions ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with ISO 15552

More information

Large Bore Extruded Cylinders, ISO 6431 Series 41

Large Bore Extruded Cylinders, ISO 6431 Series 41 Large Bore Extruded Cylinders, ISO 6431 Series 41 Double-acting cushioned, magnetic ø160-200 (DIN/ISO 6431)»» DIN/ISO 6431 VDMA 24562»» Rolled stainless steel rod»» Adjustable cushioning Cylinders Series

More information

Single- and double-acting, cushioned, magnetic ø 32, 40, 50, 63, 80, 100 and 125 mm

Single- and double-acting, cushioned, magnetic ø 32, 40, 50, 63, 80, 100 and 125 mm > Series 90 stainless steel cylinders CATALOGUE > Release 8.8 Series 90 stainless steel cylinders Single- and double-acting, cushioned, magnetic ø 32, 40, 50, 63, 80, 00 and 25 mm» In compliance with ISO

More information

Series 63 ISO cylinders

Series 63 ISO cylinders Series 63 ISO 15552 cylinders New versions Single and double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with the ISO 15552 standard Weight reduced by 25% Low noise More

More information

Double acting, cushioned, magnetic Ø mm

Double acting, cushioned, magnetic Ø mm CATALOGUE > Release 8.7 > Series 40 cylinders Series 40 cylinders Double acting, cushioned, magnetic 60-200 - 250-320 mm In compliance with ISO 5552 standards and with the previous DIN/ISO 643 - VDMA 24562

More information

Series 32 compact magnetic cylinders 1/ Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 100 mm

Series 32 compact magnetic cylinders 1/ Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 100 mm Series 32 compact magnetic cylinders Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 2287»» Compact design»» Wide range of models available in different

More information

Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm

Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm > Cylinders Series 62 CATALOGUE > Release 8.5 Cylinders Series 62 Aluminium profile Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 5552 standards and with the previous

More information

Sizes 32, 40, 50 and 63

Sizes 32, 40, 50 and 63 > Series 6E electromechanical cylinders C_Electrics > 207 Series 6E electromechanical cylinders Sizes 32, 40, 50 and 63 The Series 6E cylinders are mechanical linear actuators with rod, in which the rotary

More information

Stainless steel Cylinders Series 90

Stainless steel Cylinders Series 90 90 S E R I E S Catalogue 200 Stainless steel Cylinders Series 90 DIN/ISO 643 Single and double-acting (magnetic) ø 32, 40, 50, 63, 80, 00 and 25 cushioned Stainless steel cylinders Series 90 ø 32, 40,

More information

AIR CYLINDER Series A23, A24

AIR CYLINDER Series A23, A24 A23 - Magnetic A24 - Non-magnetic Double Acting s (Square type) Ø32-125 mm As per ISO 15552 / VDMA 24562 standards. Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings

More information

Series 31 compact cylinders 1/

Series 31 compact cylinders 1/ Series 3 compact cylinders Double and single-acting, double-acting non-rotating, magnetic ø2, 6, 20, 25 mm ø 32, 40, 50, 63, 80, 00 mm UNITOP The compact dimensions allow Series 3 single and double-acting

More information

AIR CYLINDER Series A25, A26

AIR CYLINDER Series A25, A26 A25 - Magnetic A26 - Non-magnetic S Double End Double Acting - Ø32-100 mm As per ISO 15552 / VDMA 24562 standards Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings.

More information

Magnetic cylinders Series 27 1/ Double-acting, magnetic ø 20, 25, 32, 40, 50, 63 mm

Magnetic cylinders Series 27 1/ Double-acting, magnetic ø 20, 25, 32, 40, 50, 63 mm CATALOGUE > Release 8.5 > Cylinders Series 27 Magnetic cylinders Series 27 Double-acting, magnetic ø 20, 25, 32, 40, 50, 63 mm»» Reduced dimensions»» Different mounting options»» Perfect alignment, perfect

More information

AIR CYLINDER Series A12, A13

AIR CYLINDER Series A12, A13 A12 - Non magnetic A13 - Magnetic S Double Acting ( Ø32-100 ) mm As per ISO 6431 / CETOP RP43P, RP53P standards Features Adjustable cushioning at both ends Wide varieties of mountings Low friction Long

More information

Single and double-acting, cushioned, magnetic. ø 32, 40, 50, 63 mm

Single and double-acting, cushioned, magnetic. ø 32, 40, 50, 63 mm > Series 97 stainless steel cylinders CATALOGUE > Release 8.7 Series 97 stainless steel cylinders Single and double-acting, cushioned, magnetic. ø 32, 40, 50, 63 mm»» Clean design»» Stainless steel AISI

More information

Double and single-acting, double-acting non-rotating, magnetic ø12, 16, 20, 25 mm ø 32, 40, 50, 63, 80, 100 mm UNITOP

Double and single-acting, double-acting non-rotating, magnetic ø12, 16, 20, 25 mm ø 32, 40, 50, 63, 80, 100 mm UNITOP CATALOGUE > Release 8.7 > Series 3 cylinders Series 3 compact cylinders Double and single-acting, double-acting non-rotating, magnetic ø2, 6, 20, 25 mm ø 32, 40, 50, 63, 80, 00 mm UNITOP» Compact design»

More information

Pneumatic cylinders, piston-ø mm Double acting with magnetic piston DIN ISO 15552

Pneumatic cylinders, piston-ø mm Double acting with magnetic piston DIN ISO 15552 Pneumatic cylinders, piston-ø 32 100 mm Double acting with magnetic piston DIN ISO 15552 Technical data for series SL 050 450 Order code SL-032-0250-050 Series Piston-Ø Stroke length (mm) Type of cylinder

More information

XG*-***-****-***-****

XG*-***-****-***-**** Technical details Cylinders > piston rod cylinders > Series XL, ISO ISO 15552, 15552, double double acting acting Operating pressure Temperature range Max. stroke Medium Materials 1... 10 bar -20 C...

More information

SERIES PRA AND TRB ISO PNEUMATIC CYLINDERS

SERIES PRA AND TRB ISO PNEUMATIC CYLINDERS SERIES PRA AND TRB ISO 15552 PNEUMATIC CYLINDERS Series PRA and TRB Pneumatic ISO 15552 Cylinders The next generation of ISO cylinders from AVENTICS The Series PRA and TRB cylinder series represent consistent

More information

Compact cylinders series NYD Double acting with magnetic piston, ISO M5 to G1/8 Piston Ø 20 to 100 mm

Compact cylinders series NYD Double acting with magnetic piston, ISO M5 to G1/8 Piston Ø 20 to 100 mm Compact cylinders series NYD Double acting with magnetic piston, ISO 21287 M5 to G1/8 Piston Ø 20 to 100 mm 200, 210 220 600, 610 620 Order code NYD-032-125-210 High force cylinder series NYDK and multiple

More information

Series 16: ø 8, 10, 12 mm Series 24: ø 16, 20, 25 mm - magnetic Series 25: 16, 20, 25 mm - magnetic, cushioned

Series 16: ø 8, 10, 12 mm Series 24: ø 16, 20, 25 mm - magnetic Series 25: 16, 20, 25 mm - magnetic, cushioned > Series 6, 24 and 25 mini-cylinders Series 6, 24 and 25 mini-cylinders Series 6: ø 8, 0, 2 mm Series 24: ø 6, 20, 25 mm - magnetic Series 25: 6, 20, 25 mm - magnetic, cushioned» Single-acting and double-acting»

More information

2. COMPACT CYLINDERS series STRONG (RS, RQ)

2. COMPACT CYLINDERS series STRONG (RS, RQ) 2. COMPACT CYLINDERS series STRONG (RS, RQ) A new series of compact cylinders for long s and heavy-duty applications standard supplied with oversized guides and rods, the first one with adjustable pneumatic

More information

Round Body Minicylinders, DIN/ISO 6432 Series 16, 24 and 25

Round Body Minicylinders, DIN/ISO 6432 Series 16, 24 and 25 Round Body Minicylinders, DIN/ISO 6432 Series 16, 24 and 25 Series 16: ø 8-10 - 12 bumpers Series 24: ø 16-20 - 25 bumpers and magnetic piston Series 25: ø 16-20 - 25 adjustable cushion and magnetic piston»»

More information

Tie rods cylinders to ISO standard Ø

Tie rods cylinders to ISO standard Ø Tie rods cylinders to ISO 5552 standard 25 DESCRIPTION Cylinders series "XL" comply with ISO 5552 standard, being in this way completely interchangeable with the former cylinders to ISO 643 /VDMA 24562

More information

Tie rod cylinders, Series 523

Tie rod cylinders, Series 523 Electric Drives and Controls Hydralics Linear Motion and Assembly Technologies Pneumatics Service Tie rod cylinders, Series 523 Technical data Tie rod cylinders, Series 523 Grey series, 32 25 mm ( /4"-5")

More information

STANDARDISED MOUNTINGS

STANDARDISED MOUNTINGS STNDRDISED MOUNTINGS for PES / PLS cylinders conforming to ISO 15552-FNOR-DIN standard Series 434 MOUNTINGS CONFORMING TO ISO 15552 - FNOR NF ISO 15552 - DIN ISO 15552 STNDRDS B C pplications duty Construction

More information

Single-acting and double-acting, magnetic Series 94: ø 16, 20, 25 mm Series 95: ø 25 mm, cushioned

Single-acting and double-acting, magnetic Series 94: ø 16, 20, 25 mm Series 95: ø 25 mm, cushioned > Series 94 and 95 stainless steel cylinders CATALOGUE > Release 8.7 Series 94 and 95 stainless steel mini-cylinders Single-acting and double-acting, magnetic Series 94: ø 6, 20, 25 mm Series 95: ø 25

More information

compact magnetic cylinders

compact magnetic cylinders CATALOGUE > Release 8.7 > Series 32 cylinders Series 32 compact magnetic cylinders Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 2287»» Compact design»»

More information

VERSION 1 / Basic cylinder T Double push tandem R Through rod F Hollow through rod. VERSION 2 D Double acting S Single acting front spring

VERSION 1 / Basic cylinder T Double push tandem R Through rod F Hollow through rod. VERSION 2 D Double acting S Single acting front spring Compact cylinders to AFNOR NF E49-004- DESCRIPTION Cylinders series BU are available from Ø 20 to Ø 00 and, complying with AFNOR NF E49-004-, they re interchangeable also without using anchorages. Besides

More information

Tie rods cylinders to ISO standard

Tie rods cylinders to ISO standard Tie rods cylinders to ISO 5552 standard seriescpui DESCRIPTION Cylinders series CPUI comply with ISO 5552 standard, being in this way completely interchangeable with the well-known cylinders to ISO 643

More information

AIR CYLINDER Series A75, A76

AIR CYLINDER Series A75, A76 A76 - n-magnetic A75 - Magnetic AIR CYLINDER Round s - Ø32, 40, 50 and 63 mm Double Acting with Adjustable Cushioning Features Available in magnetic and n magnetic version Adjustable cushioning at both

More information

M/1000, Heavy Duty Cylinders Double Acting

M/1000, Heavy Duty Cylinders Double Acting > > Ø 2 to 12 (50 to 305 mm) > > Extremely rugged heavy duty construction - ideal for use in the most arduous conditions. > > Large range of bore sizes - ideal for a wide variety of industrial applications.

More information

Our policy is one of continued research and development. We therefore reserve the right to amend,

Our policy is one of continued research and development. We therefore reserve the right to amend, Airmotor (Oscillator) with integrated switches Double acting Ø 50... 100 mm Complete functional unit for oscillating movement Conforms to ISO 6431 and VDMA 24562 Integrated 5/2 valve Frequency and speed

More information

bar -20 C C ( C for high temperature version) 1000 mm

bar -20 C C ( C for high temperature version) 1000 mm Technical details Cylinders > piston rod cylinders > ISO 15552, double acting Operating pressure Temperature range Max. stroke Medium Materials 1... 10 bar -20 C... +80 C ( 0... +150 C for high temperature

More information

PNEUMATIC CYLINDERS CYLINDERS ISO solutions SERIES 21 SERIES 21 CYLINDERS ISO 15552

PNEUMATIC CYLINDERS CYLINDERS ISO solutions SERIES 21 SERIES 21 CYLINDERS ISO 15552 PNEUMATIC CYLINDERS 1 2 3 4 SERIEs 21- General Information 32-100 mm diameter 21 series cylinders are manufactured to ISO 15552 standard which specifies interchangeable mounting dimensions. The cylinder

More information

Profile Design Air Cylinder

Profile Design Air Cylinder Profile Design Air Cylinder Series CP5 ø, ø, ø, ø, ø, ø Features Conforms to VDMA 24 562 (parts 1 and 2), ISO 6431 and CETOP standards. Combines lightweight profile barrel design with enclosed tie rods

More information

CYLINDERS. Moving more than air

CYLINDERS. Moving more than air CYLINDRS 1 Moving more than air Content 1-2 1-2 page 1.1 Round cylinders 1.1.1 RI(M) / RI(M) / RIB(M) / RID(M) Round cylinders according to ISO 6432 piston-ø 8 25 mm 3 1.1.2 Accessories for round cylinders

More information

STANDARDISED MOUNTINGS

STANDARDISED MOUNTINGS for PS / PLS / PC cylinders conforming ISO 15552-FNOR-DIN (PS-PLS) ISO 21287 (PC) standards Series 434 MOUNTINGS CONFORMING WITH ISO 21287 - ISO 15552 - FNOR NF ISO 15552 - DIN ISO 15552 STNDRDS B C pplications

More information

ISO/TC 131/SC 3 Secretariat: DIN Voting begins on: Voting terminates on:

ISO/TC 131/SC 3 Secretariat: DIN Voting begins on: Voting terminates on: FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 15552 ISO/TC 131/SC 3 Secretariat: DIN Voting begins on: 218 1 17 Voting terminates on: 218 3 14 Pneumatic fluid power Cylinders with detachable mountings, 1

More information

RA/28000, RA/ Pneumatic Cylinders ISO 6431, VDMA and NFE Non-magnetic and Magnetic, Single Acting 32 to 100 mm

RA/28000, RA/ Pneumatic Cylinders ISO 6431, VDMA and NFE Non-magnetic and Magnetic, Single Acting 32 to 100 mm Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Single Acting 32 to 100 mm ugged tie rod construction Polyurethane seals ensure efficient low friction operation and

More information

Twin Rod Non Rotate Cylinders RDV and AZ

Twin Rod Non Rotate Cylinders RDV and AZ Twin Rod Non Rotate Cylinders RDV and AZ A range of twin rod cylinders designed for use in non rotate applications specifially suited to the handling and packaging environments. Offering a range of double

More information

RM/900/M Heavy duty cylinders Ø 1 1/4... 4

RM/900/M Heavy duty cylinders Ø 1 1/4... 4 Heavy duty cylinders Ø 1 1/4... 4 Heavy duty cylinder ideal for a wide range of rail applications Extensive range of mountings Rugged, reliable long established design Magnetic piston as standard Mounting

More information

WST Stopper Cylinder. Series WST. Specifications. How to adjust the shock absorber. Precautions. Shock absorber replacement

WST Stopper Cylinder. Series WST. Specifications. How to adjust the shock absorber. Precautions. Shock absorber replacement WST Stopper Cylinder Specifications Features Media Clean dry compressed air Operating Pressure Range 22 to 102 psi (1.5 to 7 Bar) Max* Pressure 145 psi (10 Bar) Operating Temperature Range 32 to 140 F

More information

KA/8000, KA/8000/M. Cylinder Variants. Model Codes. Standard Strokes. Warning 7/97 N/UK

KA/8000, KA/8000/M. Cylinder Variants. Model Codes. Standard Strokes. Warning 7/97 N/UK Stainless Steel VDMA/ISO Cylinders Non-magnetic and magnetic Piston Double Acting Ø 32 to 200 mm High corrosion and acid resistant Conforming to Standards ISO 6431, VDMA 24562 and NFE 49-003-1 Ideal for

More information

Series ICS and ICL Pneumatic Cylinders. Corrosion resistant stainless steel and aluminum cylinders

Series ICS and ICL Pneumatic Cylinders. Corrosion resistant stainless steel and aluminum cylinders Series ICS and ICL Pneumatic Cylinders Corrosion resistant stainless steel and aluminum cylinders Series ICS and ICL cylinders New generation of stainless steel and clean line cylinders. Series ICS from

More information

ISO Technical details

ISO Technical details Cylinders > piston rod cylinders > assembly groups > BP IO 15552 Technical details Operating pressure Cylinder with brake system XBP brake system 3... 6 bar Temperature range -10 C... +50 C Max. stroke

More information

RA/192000/M. Compact cylinder ISO Magnetic piston, double acting Ø 20 to 125 mm

RA/192000/M. Compact cylinder ISO Magnetic piston, double acting Ø 20 to 125 mm Compact cylinder ISO 2287 Magnetic piston, double acting Ø 20 to 25 mm Conforms to ISO 2287 M/50 switches can be mounted flush with the profile Magnetic piston as standard Seals ensure low friction operation

More information

1.134 L INEAR A CTUATOR: AIR C YLINDER S ERIES C95

1.134 L INEAR A CTUATOR: AIR C YLINDER S ERIES C95 1.134 L INEAR A CTUATOR: AIR C YLINDER H O W M ADE I N USA T ECHNICAL T O O R D E R C95 AIR C YLINDERS C95 P ISTON R OD S Basic K Non-Rotating P ISTON - Basic D Magnetic B ORE IN MM 50 63 80 100 B S T

More information

-H- Note. -N- Diameters. -T- Stroke lengths. -W- Note. Standard cylinders DNU/DNUL to ISO 6431 Key features at a glance Festo AG & Co.

-H- Note. -N- Diameters. -T- Stroke lengths. -W- Note. Standard cylinders DNU/DNUL to ISO 6431 Key features at a glance Festo AG & Co. Standard cylinders DNU/DNUL to ISO 6431 Key features at a glance ISO and standard cylinders DNU/DNUL -H- Note For new applications use type DNC ( -54). -N- Diameters 32... 125 mm -T- Stroke lengths 10...

More information

PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M

PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M PA/181000, PA/181000/M PA/183000, PA/183000/M Profile barrel with concealed tie rods Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Single Acting 32 to 100 mm

More information

TELESCOPIC CYLINDERS ø mm Series RT

TELESCOPIC CYLINDERS ø mm Series RT TELESCOPIC CYLINDERS 25 63 mm Series RT The overall dimensions are one of the most imporant aspects: in comparison with a traditional ISO cylinder of the same a reduction in size of approx. 45% (with a

More information

P1D-B Pneumatic Cylinders

P1D-B Pneumatic Cylinders P1D-B Pneumatic Cylinders According to ISO 15552 P1D-B series. This series features a profile design and is the basic ISO cylinder for simple applications where no special options are required. This series

More information

Strokes Strokes Double acting. Min. stroke with 2 sensors Ø Single acting. Single acting

Strokes Strokes Double acting. Min. stroke with 2 sensors Ø Single acting. Single acting S version Type... Standards... Cushioning... Rated temperature... Fluid... Working pressure... Proximity switch... Mounting and accessories... Materials... Single and double acting pneumatic microcylinders,

More information

LPRA/182000/M Double acting profile cylinders Ø mm

LPRA/182000/M Double acting profile cylinders Ø mm Double acting profile cylinders 32... 125 mm High performance, stability and reliability M/50 switches (solid state) can be mounted flush with the profile Cylinders and mountings conform to ISO 15552 (ISO

More information

ISO CYLINDERS SERIES HCR (High Corrosion Resistance) ACTUATORS

ISO CYLINDERS SERIES HCR (High Corrosion Resistance) ACTUATORS ISO 15552 CYLINDERS SERIES HCR (High Corrosion Resistance) 1 ISO 15552 CYLINDERS SERIES HCR (High Corrosion Resistance) In some applications, the cylinders are exposed to aggressive environments (e.g.

More information

12/95 N Our policy is one of continued research and development. We therefore reserve the right

12/95 N Our policy is one of continued research and development. We therefore reserve the right Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Double Acting 32 to 125 mm Cylinders to VDMA Standard 24562, ISO 6431 and NFE 49-003-1 New polyurethane seals ensure

More information

ISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR

ISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR ISOCLAIR ROUND CYLINDERS to mm - single acting ISO 6432-CETOP-AFNOR FEATURES Good resistance to corrosive elements (barrel and stainless steel rod) SER SES Series 435 Type C-AS C-AS/DM GENERAL Detection

More information

Air-Oil Systems, Inc.

Air-Oil Systems, Inc. Draft Copy 06-24-09 Numatics, Inc. is a leading manufacturer of pneumatic products and motion control products. Our broad spectrum of standard, custom developed products and application components, have

More information

10/97 N Our policy is one of continued research and development. We therefore reserve the right

10/97 N Our policy is one of continued research and development. We therefore reserve the right ISO Cylinders Magnetic Piston Double Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Buffer and adjustable cushioned models Supplied complete with nose mounting

More information

Our policy is one of continued research and development. We therefore reserve the right 1/98 N

Our policy is one of continued research and development. We therefore reserve the right 1/98 N ISO Cylinders Magnetic Piston Single Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Nose mounting nut and piston rod locknut as standard Technical Data Medium:

More information

Standard cylinders DNG/DNGZS, ISO 15552

Standard cylinders DNG/DNGZS, ISO 15552 Features Brief description Double-acting For contactless position sensing With adjustable end-position cushioning at both ends Robust tie rod design Standards-based cylinders to ISO15552 (corresponds to

More information

PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M

PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M PA/181000, PA/181000/M M/50 switches can be mounted flush with the profile Conforms to DIN ISO 6431 and VDMA 24562 part 1 Mountings conform to DIN ISO 6431, VDMA 24562 part 2 and NFE 49-003-1 Polyurethane

More information

ISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR

ISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR ISOCLAIR ROUND CYLINDERS to mm - single acting ISO 6432-CETOP-AFNOR FEATURES Good resistance to corrosive elements (barrel and stainless steel rod) GENERAL Detection Equipped or not for magnetic position

More information

Short-stroke cylinders ADVC/AEVC

Short-stroke cylinders ADVC/AEVC Short-stroke cylinders ADVC/AEVC q/w Worldwide: Superb: Easy: Festo core product range Covers 80% of your automation tasks Always in stock Festo quality at an attractive price Reduces procurement and storing

More information

HEAVY DUTY PNEUMATIC CYLINDERS

HEAVY DUTY PNEUMATIC CYLINDERS HEAVY DUTY PNEUMATIC CYLINDES Features: Conforms to ISO:30 standard. Double Acting, with adj. cushioning at both ends. Sizes: Ø, Ø, Ø, Ø, Ø, Ø0, Ø1, Ø0, Ø0 & Ø0. : Other bore sizes on request Seamless

More information

AS/ASH SERIES ALUMINUM PNEUMATIC AND HYDRAULIC CYLINDERS... 6

AS/ASH SERIES ALUMINUM PNEUMATIC AND HYDRAULIC CYLINDERS... 6 AS/ASH SERIES ALUMINUM PNEUMATIC AND HYDRAULIC CYLINDERS............. 6 Section 6 8 ORDERING INFORMATION For Rod End Dimensions see back cover foldout... Basic Cylinder No Mount.0" to 4.00" For pressure

More information

Stainless Steel Cylinders Acid and Corrosion Resistant

Stainless Steel Cylinders Acid and Corrosion Resistant Stainless Steel Cylinders Acid and Corrosion Resistant Subject to change 133 Stainless Steel Cylinders Contents Stainless Steel Double-Acting Cylinders per ISO 6432 Bores 12 to 25 mm Type CRDSNU... 137

More information

TECHNICAL CHARACTERISTICS

TECHNICAL CHARACTERISTICS 2 or 3-stage telescopic pneumatic cylinder Considering its high technological contents, this cylinder series represents without doubt the product with the highest degree of technical research and evolution

More information

PRA/182000, PRA/182000/M

PRA/182000, PRA/182000/M Profile barrel with concealed tie rods Pneumatic Profile Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Double Acting Ø 32 to 125 mm M/50 Switches can be mounted flush

More information

AZ Cylinder. Specifications. Features: Features Type ISO 6431 VDMA CETOP RP43P. Ø32mm - 100mm ISO 6431 VDMA CETOP RP43P.

AZ Cylinder. Specifications. Features: Features Type ISO 6431 VDMA CETOP RP43P. Ø32mm - 100mm ISO 6431 VDMA CETOP RP43P. Specifications Features Type ISO 6431 VDM 24562 CTOP P43P Series Z Configurations Z Double cting, Single od, Magnetic Piston, Cushions ZD Double cting, Double od, Magnetic Piston Construction Materials

More information

PRA/822000/M, PRA/ Smoothline cylinder Magnetic or non-magnetic piston, double acting

PRA/822000/M, PRA/ Smoothline cylinder Magnetic or non-magnetic piston, double acting P/822000/M, P/822000 Smoothline cylinder > 32... 00 mm > Cylinder and mounting conform to ISO 5552 > eed or solid state switches can be mounted flush with the profile barrel > lternative air ports as standard

More information

Air Cylinders Type : ISO-6431 & VDMA-24562

Air Cylinders Type : ISO-6431 & VDMA-24562 Air Cylinders Type : ISO-6 & VDMA-262 Conform to ISO: 6 & VDMA: 262 standards. Double acting, with adj. cushioning at both ends. sizes : Ø, Ø, Ø, Ø, Ø, Ø0, Ø1, Ø0 & Ø0 Profiled aluminum tube with hard

More information

RA/8000, RA/8000/M. Pneumatic cylinders ISO 6431, VDMA and NFE Non-magnetic and magnetic piston Double acting Ø 32 to 320 mm

RA/8000, RA/8000/M. Pneumatic cylinders ISO 6431, VDMA and NFE Non-magnetic and magnetic piston Double acting Ø 32 to 320 mm Pneumatic cylinders ISO 6431, VDMA 456 and NFE 49-003-1 Non-magnetic and magnetic piston Double acting Ø 3 to 30 mm Comprehensive range for the utmost versatility Conforms to DIN ISO 6431, VDMA 456 and

More information

PVA/182000, PVA/182000/M

PVA/182000, PVA/182000/M Smooth Line cylinders with or without integrated switches Double acting Ø 3... 100 mm Smooth and spherical profile design with concealed tie rods Special polyurethane wiper seal Body sealing conforms to

More information

DIE DESIGN AND CONSTRUCTION SPECIFICATIONS STAMPING - EUROPE METRIC AIR CYLINDER

DIE DESIGN AND CONSTRUCTION SPECIFICATIONS STAMPING - EUROPE METRIC AIR CYLINDER METRIC AIR CYLINDER WITH STAINLESS STEEL PISTON ROD, ALUMINIUM CYLINDER TUBE AND WITHOUT MAGNETIC PISTON THIS STANDARD REFERS TO THE DIMENSIONS REQUIRED FOR INTERCHANGEABILITY FOR SINGLE ROD, DOUBLE ACTING

More information

ISOCLAIR ROUND CYLINDERS Ø 32 to 63 mm - single acting ISO CETOP with elastic cushioning

ISOCLAIR ROUND CYLINDERS Ø 32 to 63 mm - single acting ISO CETOP with elastic cushioning ISOCLAIR ROUND CYLINDRS 32 to 63 mm - single acting ISO 643 - CTOP with elastic cushioning SR NS Series 438 Type CIS-NA/DM GNRAL Detection quipped for magnetic position detectors Fluid Air or neutral gas,

More information

LPRA/182000/M, ISO cylinder Magnetic piston, double acting

LPRA/182000/M, ISO cylinder Magnetic piston, double acting > > Ø 32... 125 mm > > High performance, stability and reliability > > M/50 switches can be mounted flush with the profile > > Cylinders and mountings conform to ISO 15552 (ISO 6431, VDM 24562 and NFE

More information

ELECTRIC CYLINDERS SERIES ELEKTRO ACTUATORS

ELECTRIC CYLINDERS SERIES ELEKTRO ACTUATORS ELECTRIC CYLINDERS SERIES ELEKTRO 1 ELECTRIC CYLINDER SERIES ELEKTRO ISO 15552 An electric cylinder with a connection interface in accordance with in-line version ISO 15552. The piston rod extension is

More information

Available: Cylinders till july 2000 Spares till july /98 N

Available: Cylinders till july 2000 Spares till july /98 N Available: Cylinders till july 2000 RM/55400/M Roundline Cylinders Magnetic Piston Double Acting 32 to 100 mm bore Magnet piston as standard provides a wide range of control options Attractive clean- line

More information

Series C95 ø32, ø40, ø50, ø63, ø80, ø100

Series C95 ø32, ø40, ø50, ø63, ø80, ø100 ISO Cylinder Series C ø, ø, ø, ø, ø, ø0 Dimensions conform to ISO 1, VDMA 2, CETOP RP3P. CJ1 CJP CJ2 CM2 C CG1 M C CA1 CS1 Variations Series Action Style asic Standard variations uit-in magnet Stainless

More information

PRA/182000, PRA/182000/M

PRA/182000, PRA/182000/M Profile cylinders conforms to ISO 15552 Non-magnetic and magnetic piston Double acting Ø 32 to 125 mm High performance, stability and reliability M/50 switches can be mounted flush with the profile Cylinders

More information

Series CP95 ø32, ø40, ø50, ø63, ø80, ø100

Series CP95 ø32, ø40, ø50, ø63, ø80, ø100 ISO Cylinder Series CP ø, ø, ø, ø, ø, ø0 Dimensions conform to ISO 6431, VDMA 2462, CETOP RP43P. CJ1 CJP CJ2 CM2 C8 C76 CG1 MB MB1 CP C C2 CA1 CS1 1.-1 Series CP Model Selection Execution Standard Type

More information

ISO 6020/2 industricylindre Industrial cylinders

ISO 6020/2 industricylindre Industrial cylinders According to ISO 6020/2 1991 DIN 24554, compact series 160 bar Working pressure up to 21 Mpa Maximum pressure 25 Mpa Working temperature 20 to 80 C Stroke tolerance 0 to 1.2mm for strokes up to 1000mm,

More information

Series QP - QPR short-stroke cylinders 1/ Series QP: single and double-acting

Series QP - QPR short-stroke cylinders 1/ Series QP: single and double-acting CATALOGUE > Release 8.7 > Series QP - QPR cylinders Series QP - QPR short-stroke cylinders Series QP: single and double-acting, magnetic Series QPR: double-acting magnetic, non-rotating ø 2, 6, 20, 25,

More information

PRA/882000/M/EX, IVAC Clean Line cylinder Magnetic piston, double acting

PRA/882000/M/EX, IVAC Clean Line cylinder Magnetic piston, double acting > ø 3... 100 mm > Complete functional unit with LED display > TEX-zones depending on pilot control: zones &, II 3GD, Valve control module (VCM) zones 1 & 1, II GD, Pilot control on separate specification

More information

Description. Piston rod end. Technical data. Datasheet Type 46 Single rod cylinder according to ISO 6022 / DIN 24333

Description. Piston rod end. Technical data. Datasheet Type 46 Single rod cylinder according to ISO 6022 / DIN 24333 CE CV LE MM KF MM KK Datasheet Type 46 Single rod cylinder according to ISO 6022 / DIN 24333 Description - Standard cylinder to ISO 6022, DIN 24333 - Strokes up to 2000 mm - Piston diameter: 40 320 mm

More information

Guide blocks for ISO/VDMA cylinders

Guide blocks for ISO/VDMA cylinders Actuators Guide blocks or ISO/VDMA cylinders QA/8/51/ QA/8/61/ QA/8/81/ (long coupling) QA/8/85/ (short coupling) Ø 32 to 1 mm QA/8/61/ QA/8/51/ Conorms to ISO 6431, VDMA 24562 and NFE 49 3 1 Ensures protection

More information

Features. Specification. Model. Acting type. Tube I.D. (mm) 20,25 32,40,50,63,80,100. Port size M5 0.8 G1/8. Proof pressure.

Features. Specification. Model. Acting type. Tube I.D. (mm) 20,25 32,40,50,63,80,100. Port size M5 0.8 G1/8. Proof pressure. series Table for standard stroke Stroke (mm) ø20,25 5,10,15,20,25,30,40,50,60,80,100,200 ø32,40 5,10,15,20,25,30,40,50,60,80,100,200,300 ø50,63 10,15,20,25,30,40,50,60,80,100,200,300,400 ø80,100 15,20,25,30,40,50,60,80,100,200,300,400,500

More information

ZBD 2512 Differential Cylinder Data sheet 07.16/DS13660

ZBD 2512 Differential Cylinder Data sheet 07.16/DS13660 ZBD 2512 Differential Cylinder Data sheet 07./DS Description: The STORZ hydraulic cylinder series ZBD 2512 for the nominal pressure of 250 bar is replaceable with the CDH1 series. By fixing the mounting

More information

ISO Cylinders - P1D-B

ISO Cylinders - P1D-B Flange MF1/MF2 Intended for fixed mounting of cylinder. Flange can be fitted to front or rear end cover of cylinder. Materials Flange: Surface-treated steel Mounting screws acc. to DIN 6912: Zinc-plated

More information

Compact cylinders CDC, ISO 21287, Clean Design

Compact cylinders CDC, ISO 21287, Clean Design Key features Design Easy to clean Easy to assemble Versatile With the CDC (Clean Design Compact) cylinder series, the ADN modular system has been expanded to include an easy to clean compact cylinder variant

More information