Single and double-acting, cushioned, magnetic. ø 32, 40, 50, 63 mm
|
|
|
- Ethan Harrison
- 5 years ago
- Views:
Transcription
1 > Series 97 stainless steel cylinders CATALOGUE > Release 8.7 Series 97 stainless steel cylinders Single and double-acting, cushioned, magnetic. ø 32, 40, 50, 63 mm»» Clean design»» Stainless steel AISI 304»» Adjustable endstroke cushioning Series 97 stainless steel cylinders are suitable for use in the off-shore, naval, pharmaceutical, nuclear and food industries. These cylinders are normally equipped with end-stroke cushioning which can be adjusted through a screw on the end block. In order to quieten the impact of the piston on the end block, these cylinders are also equipped with mechanical cushioning. GENERAL DATA Type of construction Operation the end blocks are screwed to the tube with an intermediate Teflon ring single-acting and double-acting Materials end blocks, tube, rod in stainless steel AISI 304 rod seals in PU, piston seals in NBR plastic guiding element, NSF H-certified lubricant Type of mounting Stroke min-max Operating temperature Operating pressure Speed Fluid threaded front and rear locking ring pins on front cap ends rear male hinge articulated rear male hinge rear female hinge mm 0 C 80 C (with dry air - 20 C) 0 bar mm/sec (without load) Filtered air, without lubrication. If lubricated air is used, it is recommended to use oil ISOVG32. Once applied the lubrication should never be interrupted. /3.20.0
2 CATALOGUE > Release 8.7 > Series 97 stainless steel cylinders STANDARD STROKES FOR CYLINDERS SERIES 97 = Single-acting = Double-acting STANDARD STROKES Ø CODING EXAMPLE 97 M 2 A 97 M 2 A 050 A A 0200 SERIES VERSIONS: M = rear male hinge S = articulated rear male hinge F = rear female hinge T = front and rear threaded end blocks A = front end block with pin OPERATION: = single-acting, front spring 2 = double-acting, front and rear cushions 6 = double-acting, through-rod, front and rear cushions (T and A versions only) MATERIALS: A = stainless steel AISI PU seals V = stainless steel AISI FKM seals (50 C) BORE: 032 = 32 mm = 40 mm = 50 mm = 63 mm TYPE OF DESIGN: A = standard (locking ring for end cap V + lock nut for rod U) STROKE (see the table) = standard V = rod seal in FKM PNEUMATIC SYMBOLS: CS06 CD09 CD3 PNEUMATIC SYMBOLS The pneumatic symbols which have been indicated in the CODING EXAMPLE are shown below. /
3 > Series 97 stainless steel cylinders CATALOGUE > Release 8.7 ACCESSORIES FOR STAINLESS STEEL CYLINDERS SERIES 97 Foot mount Mod. B Trunnion bracket Mod. I Rear female trunnion bracket Mod. C-H Tight rear female tr. bracket Mod. CR Male tr. bracket with swivel ball joint Mod. R 90 male tr. bracket + sw. ball joint Mod. ZCR Rod fork end Mod. G-90 Swivel ball joint Mod. GA-90 Piston rod lock nut Mod. U-90 Nose nut Mod. V-97 Clevis pin Mod. S-90 Anti-rotation clevis pin Mod. SR-90 All accessories are supplied separately, except for piston rod lock nut Mod. U and nose nut Mod. V. /
4 CATALOGUE > Release 8.7 > Series 97 stainless steel cylinders Cylinders Series 97, Mod. T With threaded front and rear end blocks Ø ØA AM ØB ØB2 EE F G KK PL SW KW SW2 U WH L+ L2+ L3+ L4 L7 KW ØKV M30x.5 36 G/ M0x M38x.5 45 G/ M2x M45x.5 55 G/ M6x M45x.5 68 G3/ M6x Cylinders Series 97, Mod. T - through-rod With threaded end blocks once + twice Ø ØA AM ØB ØB2 EE F G KK PL SW KW SW2 U WH+ L2+ L3+ L4 KW ØKV ZC M30x.5 36 G/ M0x M38x.5 45 G/ M2x M45x.5 55 G/ M6x M45x.5 68 G3/ M6x /
5 > Series 97 stainless steel cylinders CATALOGUE > Release 8.7 Cylinders Series 97, Mod. M With rear male trunnion bracket Ø ØA AM ØB2 CX EE EW KK PL SW KW SW2 U WH L+ L2+ L3+ L LU XD G/8 26 M0x G/4 28 M2x G/4 32 M6x G3/8 40 M6x Cylinders Series 97, Mod. S With articulated rear male trunnion bracket Ø ØA AM ØB2 CX EE EP EX KK PL SW KW SW2 U WH L+ L2+ L3+ LT LU XD+ Z G/ M0x G/4 2 6 M2x G/4 5 2 M6x G3/8 5 2 M6x /
6 CATALOGUE > Release 8.7 > Series 97 stainless steel cylinders Cylinders Series 97, Mod. F With rear female trunnion bracket Ø ØA AM ØB2 CB CX EE KK PL SW KW SW2 U WH L+ L2+ L3+ L LU XD+ UB G/8 M0x G/4 M2x G/4 M6x G3/8 M6x Cylinders Series 97, Mod. A With front end block with pins Ø ØA AM ØB2 EE KK SW SW KW SW2 U WH L+ L2+ L3+ LU XG TD TL UT G/8 M0x G/4 M2x G/4 M6x G3/8 M6x /
7 > Series 97 stainless steel cylinders CATALOGUE > Release 8.7 Foot mount Mod. B Material: stainless steel 304 x nut 2x single feet Mod. Ø A B C D E SA+ F G ØH ØM XD+ B B B B Trunnion bracket Mod. I Material: stainless steel 304 x female trunnion 2x cartridges Mod. Ø C C C2 ØD E F G G G2 L+ SW I I I I Rear female trunnion bracket Mod. C-H Material: stainless steel 36 x female trunnion bracket 4x screws Mod. Ø CB CD E FL L MR UB XD+ C-H C-H C-H C-H /
8 CATALOGUE > Release 8.7 > Series 97 stainless steel cylinders Tight rear female trunnion bracket Mod. CR Material: stainless steel 36 x female trunnion bracket 4x screws Mod. Ø B B2 E CN FL XD+ CR CR CR CR Male trunnion bracket with swivel ball joint Mod. R Material: stainless steel 36 x male trunnion bracket 4x screws Mod. Ø E EN FL TG XD+ R R R R male trunnion bracket with swivel ball joint Mod. ZCR Material: stainless steel 36 x male trunnion bracket 4x screws Mod. Ø CH CN G G2 G3 H6 K K2 S5 XD+ ZCR ZCR ZCR ZCR /
9 > Series 97 stainless steel cylinders CATALOGUE > Release 8.7 Rod fork end Mod. G-90 ISO 840 Material: stainless steel 303 Mod. Ø ØCK LE CM CL ER CE KK B ØB G M0x G M2x G M6x Swivel ball joint Mod. GA-90 ISO 839 Materials: - stainless steel 304 bracket - stainless steel 420 spherical ring - sintered bronze bushing Mod. Ø ØCN U EN ER AX CE KK ØT Z SW GA M0x GA M2x GA M6x Piston rod lock nut Mod. U-90 ISO 4035 Material: stainless steel 304 Mod. Ø D m SW U M0x U M2x U M6x /
10 CATALOGUE > Release 8.7 > Series 97 stainless steel cylinders Nose nut Mod. V-97 Material: stainless steel 304 Mod. Ø A D ØD E C V M30x V M38x V M45x Clevis pin Mod. S-90 x clevis pin in stainless steel 303 2x seeger in steel Mod. Ø Ød L L L2 L3 S S S S Antirotating clevis pin Mod. SR-90 x antirotating clevis pin in stainless steel 36 x seeger in steel Mod. Ø A B C D E F G H L SR SR SR SR /3.20.0
Single- and double-acting, cushioned, magnetic ø 32, 40, 50, 63, 80, 100 and 125 mm
> Series 90 stainless steel cylinders CATALOGUE > Release 8.8 Series 90 stainless steel cylinders Single- and double-acting, cushioned, magnetic ø 32, 40, 50, 63, 80, 00 and 25 mm» In compliance with ISO
Single-acting and double-acting, magnetic Series 94: ø 16, 20, 25 mm Series 95: ø 25 mm, cushioned
> Series 94 and 95 stainless steel cylinders CATALOGUE > Release 8.7 Series 94 and 95 stainless steel mini-cylinders Single-acting and double-acting, magnetic Series 94: ø 6, 20, 25 mm Series 95: ø 25
Double acting, cushioned, magnetic Ø mm
CATALOGUE > Release 8.7 > Series 40 cylinders Series 40 cylinders Double acting, cushioned, magnetic 60-200 - 250-320 mm In compliance with ISO 5552 standards and with the previous DIN/ISO 643 - VDMA 24562
Aluminium profile. Double-acting, cushioned, magnetic ø mm
> Series 4 cylinders Series 4 cylinders - Aluminium profile Double-acting, cushioned, magnetic ø 60-200 mm»» In compliance with ISO 643/ VDMA 24562 standards»» Rolled stainless steel rod»» Adjustable pneumatic
Series 32 compact magnetic cylinders 1/ Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 100 mm
Series 32 compact magnetic cylinders Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 2287»» Compact design»» Wide range of models available in different
Cylinders Series 61 - Aluminium profile
CATALOGUE > Release 8. Cylinders Series 6 - Aluminium profile MOVEMENT > Cylinders Series 6 Single, double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00, 25 (ISO 5552)» ISO 5552 (corresponding to
Series 31 compact cylinders 1/
Series 3 compact cylinders Double and single-acting, double-acting non-rotating, magnetic ø2, 6, 20, 25 mm ø 32, 40, 50, 63, 80, 00 mm UNITOP The compact dimensions allow Series 3 single and double-acting
Large Bore Extruded Cylinders, ISO 6431 Series 41
Large Bore Extruded Cylinders, ISO 6431 Series 41 Double-acting cushioned, magnetic ø160-200 (DIN/ISO 6431)»» DIN/ISO 6431 VDMA 24562»» Rolled stainless steel rod»» Adjustable cushioning Cylinders Series
Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm
> Series 62 cylinders CATALOGUE > Release 8.6 Series 62 cylinders - Aluminium profile Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 5552 standards and with the
Aluminium tube and profile
> Series 63 cylinders CATALOGUE > 206 Series 63 cylinders - Aluminium tube and profile New Single and double-acting, magnetic, cushioned Versions: standard, low friction, high and low temperatures ø 32,
Aluminium profile. TANDEM: Double thrust and traction forces. LOW FRICTION: Friction force reduced by over 40%
CATALOGUE > Release 8.7 > Series 6 cylinders Series 6 cylinders - Aluminium profile Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40,
Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 100, 125mm
CATALOGUE > Release 8.8 > Series 60 cylinders Series 60 cylinders Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 00, 25mm»»
Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 100, 125mm
CATALOGUE > Release 8.6 > Series 60 cylinders Series 60 cylinders New version Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 00,
Magnetic cylinders Series 27 1/ Double-acting, magnetic ø 20, 25, 32, 40, 50, 63 mm
CATALOGUE > Release 8.5 > Cylinders Series 27 Magnetic cylinders Series 27 Double-acting, magnetic ø 20, 25, 32, 40, 50, 63 mm»» Reduced dimensions»» Different mounting options»» Perfect alignment, perfect
Series 6PF Positioning Feedback cylinders 1/ Double-acting low friction, magnetic ø 50, 63, 80, 100, 125 mm
CATALOGUE > Release 8.8 > Series 6PF cylinders Series 6PF Positioning Feedback cylinders Double-acting low friction, magnetic ø 50, 63, 80, 00, 25 mm»» In compliance with ISO 5552 standards and with the
Bore ø 32, 40, 50, 63, 80, 100, 125 Ports 32 = 1/8, 40/50 = 1/4, 63/80 = 3/8, 100/125 = 1/2
6 S E R I E S Cylinders Series 6 Catalog 2006 Single, double acting, magnetic (DIN/ISO 643) Bore: ø 32, 40, 50, 63, 80, 00, 25 cushioned [ /4, 9/6, 2, 2 /2, 3 /8, 4, 5 inch approximations] The Series 6
Stainless steel Cylinders Series 90
90 S E R I E S Catalogue 200 Stainless steel Cylinders Series 90 DIN/ISO 643 Single and double-acting (magnetic) ø 32, 40, 50, 63, 80, 00 and 25 cushioned Stainless steel cylinders Series 90 ø 32, 40,
Double and single-acting, double-acting non-rotating, magnetic ø12, 16, 20, 25 mm ø 32, 40, 50, 63, 80, 100 mm UNITOP
CATALOGUE > Release 8.7 > Series 3 cylinders Series 3 compact cylinders Double and single-acting, double-acting non-rotating, magnetic ø2, 6, 20, 25 mm ø 32, 40, 50, 63, 80, 00 mm UNITOP» Compact design»
Tie-rod Cylinders, ISO 6431, ISO compliant Series 60
Tie-rod Cylinders, ISO 6431, ISO 15552 compliant Series 60 Single or double-acting, magnetic, cushioned Standard and low friction versions ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with ISO 15552
Extruded Body Cylinders, ISO 6431, ISO compliant Series 61
1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Extruded Body Cylinders, ISO 6431, ISO 15552 compliant Series 61 Single or double-acting, magnetic, cushioned Standard and
Series 63 ISO cylinders
Series 63 ISO 15552 cylinders New versions Single and double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with the ISO 15552 standard Weight reduced by 25% Low noise More
compact magnetic cylinders
CATALOGUE > Release 8.7 > Series 32 cylinders Series 32 compact magnetic cylinders Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 2287»» Compact design»»
Round Body Minicylinders, DIN/ISO 6432 Series 16, 24 and 25
Round Body Minicylinders, DIN/ISO 6432 Series 16, 24 and 25 Series 16: ø 8-10 - 12 bumpers Series 24: ø 16-20 - 25 bumpers and magnetic piston Series 25: ø 16-20 - 25 adjustable cushion and magnetic piston»»
Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm
> Cylinders Series 62 CATALOGUE > Release 8.5 Cylinders Series 62 Aluminium profile Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 5552 standards and with the previous
Series 16: ø 8, 10, 12 mm Series 24: ø 16, 20, 25 mm - magnetic Series 25: 16, 20, 25 mm - magnetic, cushioned
> Series 6, 24 and 25 mini-cylinders Series 6, 24 and 25 mini-cylinders Series 6: ø 8, 0, 2 mm Series 24: ø 6, 20, 25 mm - magnetic Series 25: 6, 20, 25 mm - magnetic, cushioned» Single-acting and double-acting»
AIR CYLINDER Series A25, A26
A25 - Magnetic A26 - Non-magnetic S Double End Double Acting - Ø32-100 mm As per ISO 15552 / VDMA 24562 standards Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings.
AIR CYLINDER Series A23, A24
A23 - Magnetic A24 - Non-magnetic Double Acting s (Square type) Ø32-125 mm As per ISO 15552 / VDMA 24562 standards. Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings
Series QP - QPR short-stroke cylinders 1/ Series QP: single and double-acting
CATALOGUE > Release 8.7 > Series QP - QPR cylinders Series QP - QPR short-stroke cylinders Series QP: single and double-acting, magnetic Series QPR: double-acting magnetic, non-rotating ø 2, 6, 20, 25,
AIR CYLINDER Series A12, A13
A12 - Non magnetic A13 - Magnetic S Double Acting ( Ø32-100 ) mm As per ISO 6431 / CETOP RP43P, RP53P standards Features Adjustable cushioning at both ends Wide varieties of mountings Low friction Long
Sizes 32, 40, 50 and 63
> Series 6E electromechanical cylinders C_Electrics > 207 Series 6E electromechanical cylinders Sizes 32, 40, 50 and 63 The Series 6E cylinders are mechanical linear actuators with rod, in which the rotary
Series CP95 ø32, ø40, ø50, ø63, ø80, ø100
ISO Cylinder Series CP ø, ø, ø, ø, ø, ø0 Dimensions conform to ISO 6431, VDMA 2462, CETOP RP43P. CJ1 CJP CJ2 CM2 C8 C76 CG1 MB MB1 CP C C2 CA1 CS1 1.-1 Series CP Model Selection Execution Standard Type
Cylinders with integrated guide Series QCTF and QCBF
> Series QCTF - QCBF slide units CATALOGUE > Release 8.6 Cylinders with integrated guide Series QCTF and QCBF Double-acting, magnetic, with double bearings and flanges ø 20, 25, 32, 40 mm Magnetic sensors
Series ICS and ICL Pneumatic Cylinders. Corrosion resistant stainless steel and aluminum cylinders
Series ICS and ICL Pneumatic Cylinders Corrosion resistant stainless steel and aluminum cylinders Series ICS and ICL cylinders New generation of stainless steel and clean line cylinders. Series ICS from
Our policy is one of continued research and development. We therefore reserve the right to amend,
Airmotor (Oscillator) with integrated switches Double acting Ø 50... 100 mm Complete functional unit for oscillating movement Conforms to ISO 6431 and VDMA 24562 Integrated 5/2 valve Frequency and speed
XG*-***-****-***-****
Technical details Cylinders > piston rod cylinders > Series XL, ISO ISO 15552, 15552, double double acting acting Operating pressure Temperature range Max. stroke Medium Materials 1... 10 bar -20 C...
ISO CYLINDERS SERIES HCR (High Corrosion Resistance) ACTUATORS
ISO 15552 CYLINDERS SERIES HCR (High Corrosion Resistance) 1 ISO 15552 CYLINDERS SERIES HCR (High Corrosion Resistance) In some applications, the cylinders are exposed to aggressive environments (e.g.
SERIES PRA AND TRB ISO PNEUMATIC CYLINDERS
SERIES PRA AND TRB ISO 15552 PNEUMATIC CYLINDERS Series PRA and TRB Pneumatic ISO 15552 Cylinders The next generation of ISO cylinders from AVENTICS The Series PRA and TRB cylinder series represent consistent
PNEUMATIC CYLINDERS CYLINDERS ISO solutions SERIES 21 SERIES 21 CYLINDERS ISO 15552
PNEUMATIC CYLINDERS 1 2 3 4 SERIEs 21- General Information 32-100 mm diameter 21 series cylinders are manufactured to ISO 15552 standard which specifies interchangeable mounting dimensions. The cylinder
PVA/182000, PVA/182000/M
Smooth Line cylinders with or without integrated switches Double acting Ø 3... 100 mm Smooth and spherical profile design with concealed tie rods Special polyurethane wiper seal Body sealing conforms to
AIR CYLINDER Series A75, A76
A76 - n-magnetic A75 - Magnetic AIR CYLINDER Round s - Ø32, 40, 50 and 63 mm Double Acting with Adjustable Cushioning Features Available in magnetic and n magnetic version Adjustable cushioning at both
Compact cylinders series NYD Double acting with magnetic piston, ISO M5 to G1/8 Piston Ø 20 to 100 mm
Compact cylinders series NYD Double acting with magnetic piston, ISO 21287 M5 to G1/8 Piston Ø 20 to 100 mm 200, 210 220 600, 610 620 Order code NYD-032-125-210 High force cylinder series NYDK and multiple
STANDARDISED MOUNTINGS
STNDRDISED MOUNTINGS for PES / PLS cylinders conforming to ISO 15552-FNOR-DIN standard Series 434 MOUNTINGS CONFORMING TO ISO 15552 - FNOR NF ISO 15552 - DIN ISO 15552 STNDRDS B C pplications duty Construction
bar -20 C C ( C for high temperature version) 1000 mm
Technical details Cylinders > piston rod cylinders > ISO 15552, double acting Operating pressure Temperature range Max. stroke Medium Materials 1... 10 bar -20 C... +80 C ( 0... +150 C for high temperature
Profile Design Air Cylinder
Profile Design Air Cylinder Series CP5 ø, ø, ø, ø, ø, ø Features Conforms to VDMA 24 562 (parts 1 and 2), ISO 6431 and CETOP standards. Combines lightweight profile barrel design with enclosed tie rods
VERSION 1 / Basic cylinder T Double push tandem R Through rod F Hollow through rod. VERSION 2 D Double acting S Single acting front spring
Compact cylinders to AFNOR NF E49-004- DESCRIPTION Cylinders series BU are available from Ø 20 to Ø 00 and, complying with AFNOR NF E49-004-, they re interchangeable also without using anchorages. Besides
Double-acting, magnetic, guided ø 10x2, 16x2, 20x2, 25x2, 32x2 mm
CATALOGUE > Release 8.8 > Series QX twin rod cylinders Series QX twin cylinders Double-acting, magnetic, guided ø 0x2, 6x2, 20x2, 25x2, 32x2 mm High force Precise movement Integrated guide QXB: linear
ISO 6020/2 industricylindre Industrial cylinders
According to ISO 6020/2 1991 DIN 24554, compact series 160 bar Working pressure up to 21 Mpa Maximum pressure 25 Mpa Working temperature 20 to 80 C Stroke tolerance 0 to 1.2mm for strokes up to 1000mm,
ISO CYLINDERS Ø ACTUATORS
ISO 15552 CYLINDERS Ø 250-320 1 Cylinders made to ISO 15552 available in various versions and with a wide range of accessories: double-acting single-or through-rod with or without cushioning configuration
M/1000, Heavy Duty Cylinders Double Acting
> > Ø 2 to 12 (50 to 305 mm) > > Extremely rugged heavy duty construction - ideal for use in the most arduous conditions. > > Large range of bore sizes - ideal for a wide variety of industrial applications.
Tie rod cylinders, Series 523
Electric Drives and Controls Hydralics Linear Motion and Assembly Technologies Pneumatics Service Tie rod cylinders, Series 523 Technical data Tie rod cylinders, Series 523 Grey series, 32 25 mm ( /4"-5")
HEAVY DUTY PNEUMATIC CYLINDERS
HEAVY DUTY PNEUMATIC CYLINDES Features: Conforms to ISO:30 standard. Double Acting, with adj. cushioning at both ends. Sizes: Ø, Ø, Ø, Ø, Ø, Ø0, Ø1, Ø0, Ø0 & Ø0. : Other bore sizes on request Seamless
KA/8000, KA/8000/M. Cylinder Variants. Model Codes. Standard Strokes. Warning 7/97 N/UK
Stainless Steel VDMA/ISO Cylinders Non-magnetic and magnetic Piston Double Acting Ø 32 to 200 mm High corrosion and acid resistant Conforming to Standards ISO 6431, VDMA 24562 and NFE 49-003-1 Ideal for
Double-acting, magnetic, cushioned ø16, 25, 32, 40, 50, 63, 80
> Cylinders Series 50 CATALOGUE > Release 8.5 Rodless cylinders Series 50 Double-acting, magnetic, cushioned ø6, 25, 32, 40, 50, 63, 80»» Four ports on each chamber»» Possibility to supply both chambers
P1D-B Pneumatic Cylinders
P1D-B Pneumatic Cylinders According to ISO 15552 P1D-B series. This series features a profile design and is the basic ISO cylinder for simple applications where no special options are required. This series
2. COMPACT CYLINDERS series STRONG (RS, RQ)
2. COMPACT CYLINDERS series STRONG (RS, RQ) A new series of compact cylinders for long s and heavy-duty applications standard supplied with oversized guides and rods, the first one with adjustable pneumatic
Pneumatic cylinders, piston-ø mm Double acting with magnetic piston DIN ISO 15552
Pneumatic cylinders, piston-ø 32 100 mm Double acting with magnetic piston DIN ISO 15552 Technical data for series SL 050 450 Order code SL-032-0250-050 Series Piston-Ø Stroke length (mm) Type of cylinder
ISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR
ISOCLAIR ROUND CYLINDERS to mm - single acting ISO 6432-CETOP-AFNOR FEATURES Good resistance to corrosive elements (barrel and stainless steel rod) SER SES Series 435 Type C-AS C-AS/DM GENERAL Detection
Available: Cylinders till july 2000 Spares till july /98 N
Available: Cylinders till july 2000 RM/55400/M Roundline Cylinders Magnetic Piston Double Acting 32 to 100 mm bore Magnet piston as standard provides a wide range of control options Attractive clean- line
Cylinders DIN ISO 6431 and VDMA Bores from 32 to 125 mm
Double acting Standard executions Version Shape of barrel Symbol Type MAGNETIC STANDARD AMA AMT 1 For the magnetic reed switches type ASV see from page 1.110.1. For coupling cylinders/reed swiches/brackets
RM/900/M Heavy duty cylinders Ø 1 1/4... 4
Heavy duty cylinders Ø 1 1/4... 4 Heavy duty cylinder ideal for a wide range of rail applications Extensive range of mountings Rugged, reliable long established design Magnetic piston as standard Mounting
Our policy is one of continued research and development. We therefore reserve the right
Corrosion resistant design Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Magnetic Piston Double Acting Ø 32 to 100 mm Accepted in the Food Industry Conforms to ISO 6431, VDMA 24562 and NFE
ISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR
ISOCLAIR ROUND CYLINDERS to mm - single acting ISO 6432-CETOP-AFNOR FEATURES Good resistance to corrosive elements (barrel and stainless steel rod) GENERAL Detection Equipped or not for magnetic position
ISOCLAIR ROUND CYLINDERS Ø 32 to 63 mm - single acting ISO CETOP with elastic cushioning
ISOCLAIR ROUND CYLINDRS 32 to 63 mm - single acting ISO 643 - CTOP with elastic cushioning SR NS Series 438 Type CIS-NA/DM GNRAL Detection quipped for magnetic position detectors Fluid Air or neutral gas,
PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M
PA/181000, PA/181000/M PA/183000, PA/183000/M Profile barrel with concealed tie rods Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Single Acting 32 to 100 mm
RA/192000/M. Compact cylinder ISO Magnetic piston, double acting Ø 20 to 125 mm
Compact cylinder ISO 2287 Magnetic piston, double acting Ø 20 to 25 mm Conforms to ISO 2287 M/50 switches can be mounted flush with the profile Magnetic piston as standard Seals ensure low friction operation
Our policy is one of continued research and development. We therefore reserve the right 1/98 N
ISO Cylinders Magnetic Piston Single Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Nose mounting nut and piston rod locknut as standard Technical Data Medium:
12/95 N Our policy is one of continued research and development. We therefore reserve the right
Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Double Acting 32 to 125 mm Cylinders to VDMA Standard 24562, ISO 6431 and NFE 49-003-1 New polyurethane seals ensure
RA/28000, RA/ Pneumatic Cylinders ISO 6431, VDMA and NFE Non-magnetic and Magnetic, Single Acting 32 to 100 mm
Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Single Acting 32 to 100 mm ugged tie rod construction Polyurethane seals ensure efficient low friction operation and
1/96 N Our policy is one of continued research and development. We therefore reserve the right
Roundline Cylinders Magnetic Piston Double cting 8 to 63 mm Very compact and shorter than the basic length of a corresponding ISO/VDM and roundline cylinder. Magnetic piston as standard provides a wide
Tie rods cylinders to ISO standard Ø
Tie rods cylinders to ISO 5552 standard 25 DESCRIPTION Cylinders series "XL" comply with ISO 5552 standard, being in this way completely interchangeable with the former cylinders to ISO 643 /VDMA 24562
Tie rods cylinders to ISO standard
Tie rods cylinders to ISO 5552 standard seriescpui DESCRIPTION Cylinders series CPUI comply with ISO 5552 standard, being in this way completely interchangeable with the well-known cylinders to ISO 643
CYLINDERS. Moving more than air
CYLINDRS 1 Moving more than air Content 1-2 1-2 page 1.1 Round cylinders 1.1.1 RI(M) / RI(M) / RIB(M) / RID(M) Round cylinders according to ISO 6432 piston-ø 8 25 mm 3 1.1.2 Accessories for round cylinders
Pneumatic cylinders series CX Double acting with magnetic piston, ISO 15552, stainless steel G1/8 to G1/2 piston Ø 32 to 100 mm
Pneumatic cylinders series CX Double acting with magnetic piston, ISO 15552, stainless steel 000 400 Order code CX-032-0250-000 Note: Piston Ø 125, 160 and 200 on request. Series Piston Ø Stroke length
LPRA/182000/M, ISO cylinder Magnetic piston, double acting
> > Ø 32... 125 mm > > High performance, stability and reliability > > M/50 switches can be mounted flush with the profile > > Cylinders and mountings conform to ISO 15552 (ISO 6431, VDM 24562 and NFE
RA/8000, RA/8000/M. Pneumatic cylinders ISO 6431, VDMA and NFE Non-magnetic and magnetic piston Double acting Ø 32 to 320 mm
Pneumatic cylinders ISO 6431, VDMA 456 and NFE 49-003-1 Non-magnetic and magnetic piston Double acting Ø 3 to 30 mm Comprehensive range for the utmost versatility Conforms to DIN ISO 6431, VDMA 456 and
Strokes Strokes Double acting. Min. stroke with 2 sensors Ø Single acting. Single acting
S version Type... Standards... Cushioning... Rated temperature... Fluid... Working pressure... Proximity switch... Mounting and accessories... Materials... Single and double acting pneumatic microcylinders,
Air-Oil Systems, Inc.
Draft Copy 06-24-09 Numatics, Inc. is a leading manufacturer of pneumatic products and motion control products. Our broad spectrum of standard, custom developed products and application components, have
Strokes (mm) N/en
IVC cleanline Cylinder double acting, magnetic piston 32... 100 mm Cylinders and mountings conform to ISO 15552 Complete functional unit with LED display Central electrical connector, polarity-safe Integrated
PRA/182000, PRA/182000/M
Profile barrel with concealed tie rods Pneumatic Profile Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Double Acting Ø 32 to 125 mm M/50 Switches can be mounted flush
LPRA/182000/M Double acting profile cylinders Ø mm
Double acting profile cylinders 32... 125 mm High performance, stability and reliability M/50 switches (solid state) can be mounted flush with the profile Cylinders and mountings conform to ISO 15552 (ISO
PRA/822000/M, PRA/ Smoothline cylinder Magnetic or non-magnetic piston, double acting
P/822000/M, P/822000 Smoothline cylinder > 32... 00 mm > Cylinder and mounting conform to ISO 5552 > eed or solid state switches can be mounted flush with the profile barrel > lternative air ports as standard
Via Montalbano 28 Loc.Ponte Stella, Serravalle Pistoiese C.A.P Pistoia Tel.0573/ Fax 0573/
TECHNICAL AND DIMENSIONAL CATALOGUE EDITION N 1-04 Via Montalbano 28 Loc.Ponte Stella, Serravalle Pistoiese C.A.P.51034 Pistoia Tel.0573/929163 Fax 0573/929190 E-mail: info@oleodinamicasabatini.it CAT-2004-I.doc
PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M
PA/181000, PA/181000/M M/50 switches can be mounted flush with the profile Conforms to DIN ISO 6431 and VDMA 24562 part 1 Mountings conform to DIN ISO 6431, VDMA 24562 part 2 and NFE 49-003-1 Polyurethane
V160C. Mould Hydraulic Systems. Hydraulic cylinders-iso 6020/2 compact 160 bar V160C
V160C Mould Hydraulic Systems Hydraulic cylinders-iso 6020/2 compact 160 bar V160C V160Ccat.GB01-2006 Hydraulic cylinders-iso 1 2 Chrome-plated steel rod, hardened or tempered and polished. Thickness of
1.134 L INEAR A CTUATOR: AIR C YLINDER S ERIES C95
1.134 L INEAR A CTUATOR: AIR C YLINDER H O W M ADE I N USA T ECHNICAL T O O R D E R C95 AIR C YLINDERS C95 P ISTON R OD S Basic K Non-Rotating P ISTON - Basic D Magnetic B ORE IN MM 50 63 80 100 B S T
LRA/8000/M/EX, LRA/8000/EX, ISO cylinder Magnetic & Non-magnetic piston, double acting
> > Ø 32... 320 mm > > Comprehensive range for the utmost versatility > > Wide temperature range > > Supplied complete with piston rod locknut > > Conforms to ISO 15552 (ISO 6431, VDM 24562 and NFE 49-003-1)
Features. Specification. Model. Acting type. Tube I.D. (mm) 20,25 32,40,50,63,80,100. Port size M5 0.8 G1/8. Proof pressure.
series Table for standard stroke Stroke (mm) ø20,25 5,10,15,20,25,30,40,50,60,80,100,200 ø32,40 5,10,15,20,25,30,40,50,60,80,100,200,300 ø50,63 10,15,20,25,30,40,50,60,80,100,200,300,400 ø80,100 15,20,25,30,40,50,60,80,100,200,300,400,500
Stainless Steel Cylinders Acid and Corrosion Resistant
Stainless Steel Cylinders Acid and Corrosion Resistant Subject to change 133 Stainless Steel Cylinders Contents Stainless Steel Double-Acting Cylinders per ISO 6432 Bores 12 to 25 mm Type CRDSNU... 137
TELESCOPIC CYLINDERS ø mm Series RT
TELESCOPIC CYLINDERS 25 63 mm Series RT The overall dimensions are one of the most imporant aspects: in comparison with a traditional ISO cylinder of the same a reduction in size of approx. 45% (with a
PRA/182000, PRA/182000/M
Profile cylinders conforms to ISO 15552 Non-magnetic and magnetic piston Double acting Ø 32 to 125 mm High performance, stability and reliability M/50 switches can be mounted flush with the profile Cylinders
ISO Technical details
Cylinders > piston rod cylinders > assembly groups > BP IO 15552 Technical details Operating pressure Cylinder with brake system XBP brake system 3... 6 bar Temperature range -10 C... +50 C Max. stroke
ISOCLAIR ROUND CYLINDERS Ø 32 to 63 mm - single acting ISO CETOP with elastic cushioning
ISOCLAIR ROUND CYLINDRS 32 to 63 mm - single acting ISO 643 - CTOP with elastic cushioning SR NS Series 438 Type CIS-NA/DM GNRAL Detection quipped for magnetic position detectors Fluid Air or neutral gas,
10/97 N Our policy is one of continued research and development. We therefore reserve the right
ISO Cylinders Magnetic Piston Double Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Buffer and adjustable cushioned models Supplied complete with nose mounting
Guide blocks for ISO/VDMA cylinders
Actuators Guide blocks or ISO/VDMA cylinders QA/8/51/ QA/8/61/ QA/8/81/ (long coupling) QA/8/85/ (short coupling) Ø 32 to 1 mm QA/8/61/ QA/8/51/ Conorms to ISO 6431, VDMA 24562 and NFE 49 3 1 Ensures protection
AIR CYLINDERS cylinders with pro?led barrel / tie rods standardised to ISO double acting. Series tie rods YOUR SELECTION
compact cylinders, standardised to ISO 21287 compatibility for assembly ISO 15552 mountings double acting - Series 449 short stroke cylinders single acting / double acting Series 441 AIR CYLINDERS cylinders
STANDARDISED MOUNTINGS
for PS / PLS / PC cylinders conforming ISO 15552-FNOR-DIN (PS-PLS) ISO 21287 (PC) standards Series 434 MOUNTINGS CONFORMING WITH ISO 21287 - ISO 15552 - FNOR NF ISO 15552 - DIN ISO 15552 STNDRDS B C pplications
DN series - Standard cylinder
series - cylinder Double piston packing type series ISO-431 specification series Provide CAD external dimension. DMB DU K Rod Locking his product : E End lock Use for longer stroke request DCK2 DCQ Pin
PRA/882000/M/EX, IVAC Clean Line cylinder Magnetic piston, double acting
> ø 3... 100 mm > Complete functional unit with LED display > TEX-zones depending on pilot control: zones &, II 3GD, Valve control module (VCM) zones 1 & 1, II GD, Pilot control on separate specification
Twin Rod Non Rotate Cylinders RDV and AZ
Twin Rod Non Rotate Cylinders RDV and AZ A range of twin rod cylinders designed for use in non rotate applications specifially suited to the handling and packaging environments. Offering a range of double
ANTI-CORROSIVE CYLINDERS WITH TIE RODS Ø 32 to 125 mm - double acting - ISO with adjustable pneumatic cushioning
ANTI-CORROSIVE CYLINDERS WITH TIE RODS 32 to 125 mm - double acting - ISO 15552 with adjustable pneumatic cushioning NS Series S FEATURES The cylinders are designed for use in corrosive environments: chemical,