Extruded Body Cylinders, ISO 6431, ISO compliant Series 61
|
|
|
- Alexander Mills
- 5 years ago
- Views:
Transcription
1 1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Extruded Body Cylinders, ISO 6431, ISO compliant Series 61 Single or double-acting, magnetic, cushioned Standard and low friction versions ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with ISO standards and with the previous DIN/ISO VDMA standards The Series 61 cylinders comply with the dimensions laid down in the ISO standards. A permanent magnet, mounted on the piston, enables information to be received regarding the piston position by means of proximity switches positioned along the cylinder profile. These grooves can be covered with a slot cover profile. This cylinder series is normally equipped with adjustable end-stroke cushioning. Moreover these cylinders are equipped with bumpers in order to reduce noise and the impact of the piston as it reaches the end of the stroke. Rolled stainless steel rod Adjustable pneumatic cushioning Special designs available LOW FRICTION: Friction force reduced by over 40% Reduced stick-slip effect Minimum operating pressure down to 0,1 bar (1.5 psi) Double-acting with low friction in both directions LOW TEMPERATURE: Versions for -40 C and for -50 C METAL ROD SCRAPER OPTION FOR DIRT/ICE APPLICATIONS For dirt / ice applications Resistant to dust, cement, resin, mud and wood residue GENERAL DATA Type of construction Operation Materials Type of mounting Strokes min - max Operating temperature Operating pressure Speed Fluid with tie-rods (inside the profile) double-acting, single-acting, tandem. Low friction version: double-acting only. standard = AL end-caps, rolled stainless steel rod AISI 420B, anodized AL tube, zinc-plated steel nuts and tie-rods, PU seals; low friction = standard materials with NBR piston seal and NBR rod seal (FKM rod seal on request); low temperature: standard materials with chrome plated stainless steel AISI 420B rod, brass rod scraper ring, stainless steel AISI 303 nuts, stainless steel AISI 420B tie-rods, PU piston seals and NBR rod seal with tie-rods, with front / rear flange, foot mounting, with centre / front / rear / swivel trunnion mm 0 C 80 C (with dry air - 20 C) ( F, with dry air -4 F) low temperature (-40 C version): -40 C - 60 C (with dry air -40 C) low temperature (-50 C version): -50 C - 60 C (with dry air -50 C) 1 10 bar (standard and low temperature versions) ( psi) 0,1 10 bar (low friction version) ( psi) mm/sec, no load (standard and low temperature versions) mm/sec, no load (low friction version) filtered air, without lubrication. For standard versions only: if lubricated air is used, it is recommended to use oil ISOVG32. Once applied the lubrication should never be interrupted. 28
2 NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 ISO / VDMA Cylinders 1 STANDARD STROKES FOR CYLINDERS SERIES 61 = Single-acting (standard versions) = Double-acting (standard low friction and low temperature versions) Other strokes up to 2500 mm are available on request. MAXIMUM STROKE LENGTHS (mm) Series (and Ø) Min-Max Stroke (Produced in USA) Min-Max Stroke (Produced in Italy) (Ø ) mm mm Ø CODING EXAMPLE 61 M 2 P 050 A M 2 P 050 A SERIES VERSION: M = standard, magnetic L = low friction, magnetic OPERATION: 1 = single-acting, front spring (ø 32 ± ø 100) 2 = double-acting *, front and rear cushioned 3 = double-acting *, no cushion 4 = double-acting *, rear cushioned 5 = double-acting *, front cushioned 6 = double-acting *, through-rod, front and rear cushioned 7 = single-acting, through-rod * all double-acting cylinders are also available in the low friction version. MATERIALS P = see the general data on page 1/ R = stainless steel AISI 420B tie-rods - stainless steel AISI 303 tie-rod nuts C = rolled stainless steel AISI 303 piston rod, stainless steel AISI 304 piston rod nut U = rolled stainless steel AISI 303 piston rod, AISI 304 piston-rod nut, AISI 420B tie-rods, AISI 303 tie-rod nuts W = rolled stainless steel AISI 304 piston rod, AISI304 piston-rod nut, AISI 420B tie-rods, AISI 303 tie-rod nuts Z = chrome plated stainless steel AISI 420B rod, stainless steel AISI 304 rod nut, stainless steel AISI 420B tie-rods, stainless steel AISI 303 tie-rods nuts, seals for low temperature (-40 C), brass rod scraper (Ø 125 excepted) Y = chrome plated stainless steel AISI 420B rod, stainless steel AISI 304 rod nut, stainless steel AISI 420B tie-rods, stainless steel AISI 303 tie-rods nuts, seals for low temperature (-50 C), brass rod scraper (Ø 125 excepted) BORE: 032 = 32 mm 040 = 40 mm 050 = 50 mm 063 = 63 mm 080 = 80 mm 100 = 100 mm 125 = 125 mm CONSTRUCTION: A = standard with rod nut RL = cylinder with rod lock (rod extension required. See table.) 0200 STROKE: see the table = standard V = FKM rod seal N = tandem R = NBR rod seal W = all FKM seals, up to 140 C C = PU coated cylinder. Colour: Grey * L = low friction version without rod seal (rear supply only) ** ( _ ) = extended piston rod _ mm G = with brass rod scraper (chrome plated stainless steel AISI 420B rod, NBR rod seal) (Ø 125 excepted) * Version C: available on request. For further information, please contact our technical dept. ** The possibility to order the cylinder without piston rod seal, further reduces the friction force. 29
3 1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Low friction cylinders Series 61 - APPLICATION EXAMPLES CYLINDER IN THRUST DRAWING NOTES: 1. Precision pressure regulator or electro-pneumatic regulator 2. Low friction cylinder 3. Force direction 4. Band Low temperature cylinders Series 60 - DETAIL CYLINDER IN TRACTION Note: in order to reach the highest performance, it is recommended to connect precision pressure regulator or an electro-pneumatic regulator with the low friction cylinder as shown in the drawing. Rod scraper included in all low-temperature cylinders 1 = rod seal 2 = c-clip 3 = metal scraper 30
4 NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 ISO / VDMA Cylinders 1 CYLINDERS ACCESSORIES SERIES 61 Piston rod socket joint Mod. GY Piston rod nut Mod. U Clevis pin Mod. S Rear trunnion ball-joint Mod. R Coupling piece Mod. GKF Swivel ball joint Mod. GA 90 male trunnion Mod. ZC Swivel Combination Mod. I Front and rear flange Mod. D-E Self aligning rod Mod. GK Centre trunnion Mod. F Foot mount Mod. B Front female trunnion Mod. H and C-H Rear trunnion male Mod. L Rod Gland Hard Anodized Aluminum body and integrated design includes rod bearing and rod lip/wiper seal. Rod Bearing is oil impregnated, sintered bronze containing graphite for high speed and heavy load applications. Piston Rod All stainless steel ground and polished rods, burnished for improved seal life and reduced wear. Standard. Rod Threads Threads are rolled Stainless Steel for greater strength.. Rod Nut Threads are rolled Stainless Steel for greater strength. Rear female trunnion Mod. C and C-H All accessories are supplied separately, except for piston rod nut Mod. U Tie Rod Nuts Tie rod nuts are ID hexed and ID threaded providing a flush face and ability to assemble and disassemble mounting brackets without loosening Head. Key Flat Hydraulically pressed key flat. Rod and Wiper Seal Piston rod lip seal and wiper combination. A compact design, allowing for greater bushing support without sacrificing sealing ability. Standard polyurethane. Heads and Caps Heads and Caps are lightweight aluminum that have been precision machined and anodized. Tube End Seals Captured seal made from BUNA N offering a wide range of temperature applications and positive sealing. Standard. Piston Bumpers Shock absorbing bumpers reduce noise and piston wear. Standard. Piston Aluminum, onepiece design with built-in solid magnet ensuring consistent switch sensing. Adjustable Cushion Seal Design Precision machined piston spears combined with floating cushion collar allow for a smooth deceleration at end of stroke. Cushion collar is specifically designed for rapid low pressure breakaway when stroke reverses. Rod fork end Mod. G Cushion Adjustment Recessed and captive cushion adjustment screws. Fine thread adjustment for greater repeatability and accuracy. Standard Viton. Cylinder Tube Hard Anodized Aluminum tube that provides superior seal life and wear resistance. Aluminum Extrusion Multiple slotted grooves for sensor mounting. Piston Seals Rounded lip u-cup seal reduces friction; specifically designed for lube or non lube service. Maintains factory prelube against the cylinder wall. Standard polyurethane. 31
5 1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Cylinders Series 61 N.B. : the single-acting cylinders sizes L1 and L2 are increased by 25 mm. Ø AM B BG E EE G KK L1 L2+ L3 MM N PL R RT SW1 SW2 SW3 SW4 TG VA VD WH ZJ+ front and rear cushion stroke G1/8 5 M10x1, M , / G1/4 5 M12x1, ,5 M / ,5 G1/4 8 M16x1, , M , / G3/8 8 M16x1, , M , / G3/8 8 M20x1, M / ,5 110 G1/2 8 M20x1, , M / G1/2 10,5 M27x ,5 50 M / 25 Cylinders Series 61 - through-rod Note: the single-acting cylinders sizes L1 and L2 are increased by 25 mm. + two times Ø AM B BG E EE G KK L1 L2+ L3 MM N PL R RT SW1 SW2 SW3 SW4 TG VD WH ZM++ front and rear cushion stroke G1/8 5 M10x1, M , / G1/4 5 M12x1, ,5 M / ,5 G1/4 8 M16x1, , M , / G3/8 8 M16x1, , M , / G3/8 8 M20x1, M / ,5 110 G1/2 8 M20x1, , M / G1/2 10,5 M27x ,5 50 M / 25 32
6 NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 ISO / VDMA Cylinders 1 Cylinders Series 61 - tandem version + two times Ø EE L2+ L3+ 32 G1/8 172,5 197,5 40 G1/4 191,5 221,5 50 G1/ G3/ G3/8 225,5 271,5 100 G1/ G1/ Cylinders Series 61 with rod lock ø Rod extension [X] (mm) Holding force [static load] (N) Ø ØD ØD1 ØD2 ØD3 A G H H1 L1 L2 L3 L4 L5 L6 L7 L8 L9+ L10+ M WH Z ,5 M5 25,5 46, , M6 66 M6x G1/ , M6 73 M6x ,5 G1/ , M8 94 M6x ,5 G1/ ,5 49, M8 94 M8x G1/ M M10x G1/ , M M10x G1/ , M M12x40 33
7 1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Foot mount Mod. B Material: zinc-plated steel 2x feet 4x screws Mod. Ø AT SA+ XA+ TR E AB AH AO AU B B , B , B B B ,5 14, B , Front and rear flange Mod. D-E Material: Aluminium 1x flange 4x screws Mod. Ø W MF ZB+ TF R UF E FB ZF+ torque force D-E Nm D-E Nm D-E Nm D-E Nm D-E Nm D-E Nm D-E Nm 34
8 NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 ISO / VDMA Cylinders 1 Rear female trunnion Mod. C and C-H Material: Aluminium 1x female trunnion 4x screws Mod. Ø CD L FL XD+ MR E CB UB torque force C Nm C Nm C Nm C-H Nm C-H Nm C-H Nm C-H Nm Front female trunnion Mod. H and C-H Material: Aluminium 1x female trunnion 4x screws Mod. Ø CB UB E XD FL L CD MR H H H H C-H C-H C-H
9 1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Rear male trunnion Mod. L Material: Aluminium 1x male trunnion 4x screws Mod. Ø CD L FL XD+ MR E EW torque force L Nm L Nm L Nm L Nm L Nm L Nm L Nm Centre trunnion Mod. F Material: zinc-plated steel 1x centre trunnion 8x set screws 8x clamping pins Mod. Ø XV1 XV2 XV3 TM TK TD TL UW R F ,1 F , ,15 F , , ,15 F , ,15 F , , ,15 F , , ,2 F ,2 36
10 NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 ISO / VDMA Cylinders 1 Accessory combination Mod. I (combination of models C + L + S) Material: aluminium Mod. Ø ØCD L FL XD+ TG E I M ØN torque force I , ,5 6 Nm I ,5 6 Nm I , Nm I , Nm I Nm I Nm I Nm 90 male trunnion Mod. ZC CETOP RP 107P Material: Aluminium 1x male support Mod. Ø EB CK HB XD+ TE UL EA GL L5 RA EM UR PH BT BR ZC , , ZC , , ZC , ZC , ZC , ZC , ZC , ,5 37
11 1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Trunnion ball-joint Mod. R* Material: Aluminium * not according to standard 1x trunnion ball joint 4x screws Mod. Ø CX L DL XN+ MS E EX EP Z torque force R ,5 4 6 Nm R Nm R Nm R Nm R Nm R Nm R Nm Counter bracket for centre trunnion Mod. BF Material: Aluminium 2x supports Mod. Ø CR NH C B3 TH UL FK FN B1 B2 HB BF , ,8 11 6,6 BF BF BF ,5 3,
12 NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 ISO / VDMA Cylinders 1 Accessory to mount valves on the cylinder The mounting sub-base Mod. PCV enables the valve or solenoid valve to be mounted directly on the cylinder by means of set screws that assemble through the PCV plate and into the slots of the profile extrusion. Mod. PCV-61-K3 to connect valves - solenoid valves Series 3 PCV-61-K4 to connect valves - solenoid valves Series 4 port G1/4 PCV-62-KEN to connect valves - solenoid valves Series EN PCV-61-K8 to connect valves - solenoid valves Series 4 port G1/8 and Series 3 port G1/4 Clevis pin Mod. S 1x clevis pin (stainless steel 303) 2x C-clips (plain carbon steel) Mod. Ø d L L1 L2 L3 S ,1 3 S ,1 3 S ,1 3 S ,1 3 S ,1 3 S ,3 5 S , ,3 4,25 39
13 1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Swivel ball joint Mod. GA ISO Material: zinc-plated steel. Mod. ØCN U EN ER AX CE KK T Z SW GA , M10X1, ,5 17 GA M12X1,25 17,5 6,5 19 GA M16X1,5 22 7,5 22 GA M20x1,5 27, GA M27x2 40 7,5 41 Piston rod socket joint Mod. GY Material: Zinc-Aluminum alloy and zinc-plated steel. Mod. Ø KK L CE L2 AX SW SW1 L1 L3 ØT ØD E ØB ØC Z GY M10X1, , , GY M12X1, , , GY M16X1, , GY M20x1, , , ,5 Rod fork end Mod. G Material: zinc-plated steel ISO 8140 Mod. Ø ØCK LE CM CL ER CE KK B B1 G M10 X 1, G M12 X 1, G M16 X 1, G M20 X 1, G M27 X Piston rod nut Mod. U UNI EN ISO Material: zinc-plated steel. Mod. D m SW U M10X1, U-40 M12X1, U M16X1, U M20x1, U M27x
14 NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 ISO / VDMA Cylinders 1 Self aligning rod Mod. GK Material: zinc-plated steel. Mod. Ø KK L L1 L3 L4 ØA ØD H I SW SW1 SW2 B1 AX Z E GK M10x1,25 71, , GK M12x1,25 75, , GK M16x1, GK M20x1, Coupling piece Mod. GKF Material: zinc-plated steel. Mod. Ø KK A B R TF L L1 I Ø D Ø D1 Ø D2 SW E GKF M10x1, ,5 15 6, , GKF M12x1, , ,5 GKF M16x1, , , ,5 GKF M20x1, , , ,5 GKF M27x ,
Tie-rod Cylinders, ISO 6431, ISO compliant Series 60
Tie-rod Cylinders, ISO 6431, ISO 15552 compliant Series 60 Single or double-acting, magnetic, cushioned Standard and low friction versions ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with ISO 15552
Aluminium profile. TANDEM: Double thrust and traction forces. LOW FRICTION: Friction force reduced by over 40%
CATALOGUE > Release 8.7 > Series 6 cylinders Series 6 cylinders - Aluminium profile Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40,
Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 100, 125mm
CATALOGUE > Release 8.6 > Series 60 cylinders Series 60 cylinders New version Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 00,
Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 100, 125mm
CATALOGUE > Release 8.8 > Series 60 cylinders Series 60 cylinders Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 00, 25mm»»
Cylinders Series 61 - Aluminium profile
CATALOGUE > Release 8. Cylinders Series 6 - Aluminium profile MOVEMENT > Cylinders Series 6 Single, double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00, 25 (ISO 5552)» ISO 5552 (corresponding to
Aluminium tube and profile
> Series 63 cylinders CATALOGUE > 206 Series 63 cylinders - Aluminium tube and profile New Single and double-acting, magnetic, cushioned Versions: standard, low friction, high and low temperatures ø 32,
Bore ø 32, 40, 50, 63, 80, 100, 125 Ports 32 = 1/8, 40/50 = 1/4, 63/80 = 3/8, 100/125 = 1/2
6 S E R I E S Cylinders Series 6 Catalog 2006 Single, double acting, magnetic (DIN/ISO 643) Bore: ø 32, 40, 50, 63, 80, 00, 25 cushioned [ /4, 9/6, 2, 2 /2, 3 /8, 4, 5 inch approximations] The Series 6
Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm
> Series 62 cylinders CATALOGUE > Release 8.6 Series 62 cylinders - Aluminium profile Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 5552 standards and with the
Series 6PF Positioning Feedback cylinders 1/ Double-acting low friction, magnetic ø 50, 63, 80, 100, 125 mm
CATALOGUE > Release 8.8 > Series 6PF cylinders Series 6PF Positioning Feedback cylinders Double-acting low friction, magnetic ø 50, 63, 80, 00, 25 mm»» In compliance with ISO 5552 standards and with the
Large Bore Extruded Cylinders, ISO 6431 Series 41
Large Bore Extruded Cylinders, ISO 6431 Series 41 Double-acting cushioned, magnetic ø160-200 (DIN/ISO 6431)»» DIN/ISO 6431 VDMA 24562»» Rolled stainless steel rod»» Adjustable cushioning Cylinders Series
Aluminium profile. Double-acting, cushioned, magnetic ø mm
> Series 4 cylinders Series 4 cylinders - Aluminium profile Double-acting, cushioned, magnetic ø 60-200 mm»» In compliance with ISO 643/ VDMA 24562 standards»» Rolled stainless steel rod»» Adjustable pneumatic
Series 63 ISO cylinders
Series 63 ISO 15552 cylinders New versions Single and double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with the ISO 15552 standard Weight reduced by 25% Low noise More
Round Body Minicylinders, DIN/ISO 6432 Series 16, 24 and 25
Round Body Minicylinders, DIN/ISO 6432 Series 16, 24 and 25 Series 16: ø 8-10 - 12 bumpers Series 24: ø 16-20 - 25 bumpers and magnetic piston Series 25: ø 16-20 - 25 adjustable cushion and magnetic piston»»
Double acting, cushioned, magnetic Ø mm
CATALOGUE > Release 8.7 > Series 40 cylinders Series 40 cylinders Double acting, cushioned, magnetic 60-200 - 250-320 mm In compliance with ISO 5552 standards and with the previous DIN/ISO 643 - VDMA 24562
Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm
> Cylinders Series 62 CATALOGUE > Release 8.5 Cylinders Series 62 Aluminium profile Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 5552 standards and with the previous
Single- and double-acting, cushioned, magnetic ø 32, 40, 50, 63, 80, 100 and 125 mm
> Series 90 stainless steel cylinders CATALOGUE > Release 8.8 Series 90 stainless steel cylinders Single- and double-acting, cushioned, magnetic ø 32, 40, 50, 63, 80, 00 and 25 mm» In compliance with ISO
Series 32 compact magnetic cylinders 1/ Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 100 mm
Series 32 compact magnetic cylinders Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 2287»» Compact design»» Wide range of models available in different
Sizes 32, 40, 50 and 63
> Series 6E electromechanical cylinders C_Electrics > 207 Series 6E electromechanical cylinders Sizes 32, 40, 50 and 63 The Series 6E cylinders are mechanical linear actuators with rod, in which the rotary
Series 31 compact cylinders 1/
Series 3 compact cylinders Double and single-acting, double-acting non-rotating, magnetic ø2, 6, 20, 25 mm ø 32, 40, 50, 63, 80, 00 mm UNITOP The compact dimensions allow Series 3 single and double-acting
AIR CYLINDER Series A12, A13
A12 - Non magnetic A13 - Magnetic S Double Acting ( Ø32-100 ) mm As per ISO 6431 / CETOP RP43P, RP53P standards Features Adjustable cushioning at both ends Wide varieties of mountings Low friction Long
Single and double-acting, cushioned, magnetic. ø 32, 40, 50, 63 mm
> Series 97 stainless steel cylinders CATALOGUE > Release 8.7 Series 97 stainless steel cylinders Single and double-acting, cushioned, magnetic. ø 32, 40, 50, 63 mm»» Clean design»» Stainless steel AISI
Magnetic cylinders Series 27 1/ Double-acting, magnetic ø 20, 25, 32, 40, 50, 63 mm
CATALOGUE > Release 8.5 > Cylinders Series 27 Magnetic cylinders Series 27 Double-acting, magnetic ø 20, 25, 32, 40, 50, 63 mm»» Reduced dimensions»» Different mounting options»» Perfect alignment, perfect
AIR CYLINDER Series A23, A24
A23 - Magnetic A24 - Non-magnetic Double Acting s (Square type) Ø32-125 mm As per ISO 15552 / VDMA 24562 standards. Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings
Double and single-acting, double-acting non-rotating, magnetic ø12, 16, 20, 25 mm ø 32, 40, 50, 63, 80, 100 mm UNITOP
CATALOGUE > Release 8.7 > Series 3 cylinders Series 3 compact cylinders Double and single-acting, double-acting non-rotating, magnetic ø2, 6, 20, 25 mm ø 32, 40, 50, 63, 80, 00 mm UNITOP» Compact design»
Series 16: ø 8, 10, 12 mm Series 24: ø 16, 20, 25 mm - magnetic Series 25: 16, 20, 25 mm - magnetic, cushioned
> Series 6, 24 and 25 mini-cylinders Series 6, 24 and 25 mini-cylinders Series 6: ø 8, 0, 2 mm Series 24: ø 6, 20, 25 mm - magnetic Series 25: 6, 20, 25 mm - magnetic, cushioned» Single-acting and double-acting»
Single-acting and double-acting, magnetic Series 94: ø 16, 20, 25 mm Series 95: ø 25 mm, cushioned
> Series 94 and 95 stainless steel cylinders CATALOGUE > Release 8.7 Series 94 and 95 stainless steel mini-cylinders Single-acting and double-acting, magnetic Series 94: ø 6, 20, 25 mm Series 95: ø 25
Pneumatic cylinders, piston-ø mm Double acting with magnetic piston DIN ISO 15552
Pneumatic cylinders, piston-ø 32 100 mm Double acting with magnetic piston DIN ISO 15552 Technical data for series SL 050 450 Order code SL-032-0250-050 Series Piston-Ø Stroke length (mm) Type of cylinder
AIR CYLINDER Series A25, A26
A25 - Magnetic A26 - Non-magnetic S Double End Double Acting - Ø32-100 mm As per ISO 15552 / VDMA 24562 standards Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings.
compact magnetic cylinders
CATALOGUE > Release 8.7 > Series 32 cylinders Series 32 compact magnetic cylinders Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 2287»» Compact design»»
XG*-***-****-***-****
Technical details Cylinders > piston rod cylinders > Series XL, ISO ISO 15552, 15552, double double acting acting Operating pressure Temperature range Max. stroke Medium Materials 1... 10 bar -20 C...
Compact cylinders series NYD Double acting with magnetic piston, ISO M5 to G1/8 Piston Ø 20 to 100 mm
Compact cylinders series NYD Double acting with magnetic piston, ISO 21287 M5 to G1/8 Piston Ø 20 to 100 mm 200, 210 220 600, 610 620 Order code NYD-032-125-210 High force cylinder series NYDK and multiple
Stainless steel Cylinders Series 90
90 S E R I E S Catalogue 200 Stainless steel Cylinders Series 90 DIN/ISO 643 Single and double-acting (magnetic) ø 32, 40, 50, 63, 80, 00 and 25 cushioned Stainless steel cylinders Series 90 ø 32, 40,
SERIES PRA AND TRB ISO PNEUMATIC CYLINDERS
SERIES PRA AND TRB ISO 15552 PNEUMATIC CYLINDERS Series PRA and TRB Pneumatic ISO 15552 Cylinders The next generation of ISO cylinders from AVENTICS The Series PRA and TRB cylinder series represent consistent
2. COMPACT CYLINDERS series STRONG (RS, RQ)
2. COMPACT CYLINDERS series STRONG (RS, RQ) A new series of compact cylinders for long s and heavy-duty applications standard supplied with oversized guides and rods, the first one with adjustable pneumatic
Tie rod cylinders, Series 523
Electric Drives and Controls Hydralics Linear Motion and Assembly Technologies Pneumatics Service Tie rod cylinders, Series 523 Technical data Tie rod cylinders, Series 523 Grey series, 32 25 mm ( /4"-5")
Tie rods cylinders to ISO standard Ø
Tie rods cylinders to ISO 5552 standard 25 DESCRIPTION Cylinders series "XL" comply with ISO 5552 standard, being in this way completely interchangeable with the former cylinders to ISO 643 /VDMA 24562
Tie rods cylinders to ISO standard
Tie rods cylinders to ISO 5552 standard seriescpui DESCRIPTION Cylinders series CPUI comply with ISO 5552 standard, being in this way completely interchangeable with the well-known cylinders to ISO 643
VERSION 1 / Basic cylinder T Double push tandem R Through rod F Hollow through rod. VERSION 2 D Double acting S Single acting front spring
Compact cylinders to AFNOR NF E49-004- DESCRIPTION Cylinders series BU are available from Ø 20 to Ø 00 and, complying with AFNOR NF E49-004-, they re interchangeable also without using anchorages. Besides
Profile Design Air Cylinder
Profile Design Air Cylinder Series CP5 ø, ø, ø, ø, ø, ø Features Conforms to VDMA 24 562 (parts 1 and 2), ISO 6431 and CETOP standards. Combines lightweight profile barrel design with enclosed tie rods
PNEUMATIC CYLINDERS CYLINDERS ISO solutions SERIES 21 SERIES 21 CYLINDERS ISO 15552
PNEUMATIC CYLINDERS 1 2 3 4 SERIEs 21- General Information 32-100 mm diameter 21 series cylinders are manufactured to ISO 15552 standard which specifies interchangeable mounting dimensions. The cylinder
ISO Technical details
Cylinders > piston rod cylinders > assembly groups > BP IO 15552 Technical details Operating pressure Cylinder with brake system XBP brake system 3... 6 bar Temperature range -10 C... +50 C Max. stroke
STANDARDISED MOUNTINGS
STNDRDISED MOUNTINGS for PES / PLS cylinders conforming to ISO 15552-FNOR-DIN standard Series 434 MOUNTINGS CONFORMING TO ISO 15552 - FNOR NF ISO 15552 - DIN ISO 15552 STNDRDS B C pplications duty Construction
bar -20 C C ( C for high temperature version) 1000 mm
Technical details Cylinders > piston rod cylinders > ISO 15552, double acting Operating pressure Temperature range Max. stroke Medium Materials 1... 10 bar -20 C... +80 C ( 0... +150 C for high temperature
AIR CYLINDER Series A75, A76
A76 - n-magnetic A75 - Magnetic AIR CYLINDER Round s - Ø32, 40, 50 and 63 mm Double Acting with Adjustable Cushioning Features Available in magnetic and n magnetic version Adjustable cushioning at both
ASP Series Steel Body NFPA Cylinder Line
Series Steel Body NFPA Cylinder Line www.numatics.com Table of Contents Series Features and Benefits 3 Standard Mounts 4 How to Order 5 Port Size Availability 6 Dimensions 7-34 Rod Ends 7 Large Bore 8
WST Stopper Cylinder. Series WST. Specifications. How to adjust the shock absorber. Precautions. Shock absorber replacement
WST Stopper Cylinder Specifications Features Media Clean dry compressed air Operating Pressure Range 22 to 102 psi (1.5 to 7 Bar) Max* Pressure 145 psi (10 Bar) Operating Temperature Range 32 to 140 F
Cylinders DIN ISO 6431 and VDMA Bores from 32 to 125 mm
Double acting Standard executions Version Shape of barrel Symbol Type MAGNETIC STANDARD AMA AMT 1 For the magnetic reed switches type ASV see from page 1.110.1. For coupling cylinders/reed swiches/brackets
-H- Note. -N- Diameters. -T- Stroke lengths. -W- Note. Standard cylinders DNU/DNUL to ISO 6431 Key features at a glance Festo AG & Co.
Standard cylinders DNU/DNUL to ISO 6431 Key features at a glance ISO and standard cylinders DNU/DNUL -H- Note For new applications use type DNC ( -54). -N- Diameters 32... 125 mm -T- Stroke lengths 10...
ISO CYLINDERS SERIES HCR (High Corrosion Resistance) ACTUATORS
ISO 15552 CYLINDERS SERIES HCR (High Corrosion Resistance) 1 ISO 15552 CYLINDERS SERIES HCR (High Corrosion Resistance) In some applications, the cylinders are exposed to aggressive environments (e.g.
Series ICS and ICL Pneumatic Cylinders. Corrosion resistant stainless steel and aluminum cylinders
Series ICS and ICL Pneumatic Cylinders Corrosion resistant stainless steel and aluminum cylinders Series ICS and ICL cylinders New generation of stainless steel and clean line cylinders. Series ICS from
M/1000, Heavy Duty Cylinders Double Acting
> > Ø 2 to 12 (50 to 305 mm) > > Extremely rugged heavy duty construction - ideal for use in the most arduous conditions. > > Large range of bore sizes - ideal for a wide variety of industrial applications.
Series CP95 ø32, ø40, ø50, ø63, ø80, ø100
ISO Cylinder Series CP ø, ø, ø, ø, ø, ø0 Dimensions conform to ISO 6431, VDMA 2462, CETOP RP43P. CJ1 CJP CJ2 CM2 C8 C76 CG1 MB MB1 CP C C2 CA1 CS1 1.-1 Series CP Model Selection Execution Standard Type
Series C95 ø32, ø40, ø50, ø63, ø80, ø100
ISO Cylinder Series C ø, ø, ø, ø, ø, ø0 Dimensions conform to ISO 1, VDMA 2, CETOP RP3P. CJ1 CJP CJ2 CM2 C CG1 M C CA1 CS1 Variations Series Action Style asic Standard variations uit-in magnet Stainless
AS/ASH SERIES ALUMINUM PNEUMATIC AND HYDRAULIC CYLINDERS... 6
AS/ASH SERIES ALUMINUM PNEUMATIC AND HYDRAULIC CYLINDERS............. 6 Section 6 8 ORDERING INFORMATION For Rod End Dimensions see back cover foldout... Basic Cylinder No Mount.0" to 4.00" For pressure
KA/8000, KA/8000/M. Cylinder Variants. Model Codes. Standard Strokes. Warning 7/97 N/UK
Stainless Steel VDMA/ISO Cylinders Non-magnetic and magnetic Piston Double Acting Ø 32 to 200 mm High corrosion and acid resistant Conforming to Standards ISO 6431, VDMA 24562 and NFE 49-003-1 Ideal for
Series QP - QPR short-stroke cylinders 1/ Series QP: single and double-acting
CATALOGUE > Release 8.7 > Series QP - QPR cylinders Series QP - QPR short-stroke cylinders Series QP: single and double-acting, magnetic Series QPR: double-acting magnetic, non-rotating ø 2, 6, 20, 25,
Short-stroke cylinders ADVC/AEVC
Short-stroke cylinders ADVC/AEVC q/w Worldwide: Superb: Easy: Festo core product range Covers 80% of your automation tasks Always in stock Festo quality at an attractive price Reduces procurement and storing
Our policy is one of continued research and development. We therefore reserve the right to amend,
Airmotor (Oscillator) with integrated switches Double acting Ø 50... 100 mm Complete functional unit for oscillating movement Conforms to ISO 6431 and VDMA 24562 Integrated 5/2 valve Frequency and speed
12/95 N Our policy is one of continued research and development. We therefore reserve the right
Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Double Acting 32 to 125 mm Cylinders to VDMA Standard 24562, ISO 6431 and NFE 49-003-1 New polyurethane seals ensure
RA/28000, RA/ Pneumatic Cylinders ISO 6431, VDMA and NFE Non-magnetic and Magnetic, Single Acting 32 to 100 mm
Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Single Acting 32 to 100 mm ugged tie rod construction Polyurethane seals ensure efficient low friction operation and
1.134 L INEAR A CTUATOR: AIR C YLINDER S ERIES C95
1.134 L INEAR A CTUATOR: AIR C YLINDER H O W M ADE I N USA T ECHNICAL T O O R D E R C95 AIR C YLINDERS C95 P ISTON R OD S Basic K Non-Rotating P ISTON - Basic D Magnetic B ORE IN MM 50 63 80 100 B S T
HEAVY DUTY PNEUMATIC CYLINDERS
HEAVY DUTY PNEUMATIC CYLINDES Features: Conforms to ISO:30 standard. Double Acting, with adj. cushioning at both ends. Sizes: Ø, Ø, Ø, Ø, Ø, Ø0, Ø1, Ø0, Ø0 & Ø0. : Other bore sizes on request Seamless
RA/192000/M. Compact cylinder ISO Magnetic piston, double acting Ø 20 to 125 mm
Compact cylinder ISO 2287 Magnetic piston, double acting Ø 20 to 25 mm Conforms to ISO 2287 M/50 switches can be mounted flush with the profile Magnetic piston as standard Seals ensure low friction operation
Air-Oil Systems, Inc.
Draft Copy 06-24-09 Numatics, Inc. is a leading manufacturer of pneumatic products and motion control products. Our broad spectrum of standard, custom developed products and application components, have
Twin Rod Non Rotate Cylinders RDV and AZ
Twin Rod Non Rotate Cylinders RDV and AZ A range of twin rod cylinders designed for use in non rotate applications specifially suited to the handling and packaging environments. Offering a range of double
RM/900/M Heavy duty cylinders Ø 1 1/4... 4
Heavy duty cylinders Ø 1 1/4... 4 Heavy duty cylinder ideal for a wide range of rail applications Extensive range of mountings Rugged, reliable long established design Magnetic piston as standard Mounting
CYLINDERS. Moving more than air
CYLINDRS 1 Moving more than air Content 1-2 1-2 page 1.1 Round cylinders 1.1.1 RI(M) / RI(M) / RIB(M) / RID(M) Round cylinders according to ISO 6432 piston-ø 8 25 mm 3 1.1.2 Accessories for round cylinders
Air Cylinders Type : ISO-6431 & VDMA-24562
Air Cylinders Type : ISO-6 & VDMA-262 Conform to ISO: 6 & VDMA: 262 standards. Double acting, with adj. cushioning at both ends. sizes : Ø, Ø, Ø, Ø, Ø, Ø0, Ø1, Ø0 & Ø0 Profiled aluminum tube with hard
ISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR
ISOCLAIR ROUND CYLINDERS to mm - single acting ISO 6432-CETOP-AFNOR FEATURES Good resistance to corrosive elements (barrel and stainless steel rod) SER SES Series 435 Type C-AS C-AS/DM GENERAL Detection
Standard cylinders DNG/DNGZS, ISO 15552
Features Brief description Double-acting For contactless position sensing With adjustable end-position cushioning at both ends Robust tie rod design Standards-based cylinders to ISO15552 (corresponds to
PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M
PA/181000, PA/181000/M PA/183000, PA/183000/M Profile barrel with concealed tie rods Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Single Acting 32 to 100 mm
ISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR
ISOCLAIR ROUND CYLINDERS to mm - single acting ISO 6432-CETOP-AFNOR FEATURES Good resistance to corrosive elements (barrel and stainless steel rod) GENERAL Detection Equipped or not for magnetic position
Cylinders ISO Bores from 32 to 125 mm
Cylinders ISO 5552 ores from 32 to 25 mm Double acting Standard executions Version Profile Tube Symbol Type STANDARD MAGNETIC AMA AMT For the magnetic reed switches type ASV and ASC see from page.0.. For
ISO/TC 131/SC 3 Secretariat: DIN Voting begins on: Voting terminates on:
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 15552 ISO/TC 131/SC 3 Secretariat: DIN Voting begins on: 218 1 17 Voting terminates on: 218 3 14 Pneumatic fluid power Cylinders with detachable mountings, 1
RA/8000, RA/8000/M. Pneumatic cylinders ISO 6431, VDMA and NFE Non-magnetic and magnetic piston Double acting Ø 32 to 320 mm
Pneumatic cylinders ISO 6431, VDMA 456 and NFE 49-003-1 Non-magnetic and magnetic piston Double acting Ø 3 to 30 mm Comprehensive range for the utmost versatility Conforms to DIN ISO 6431, VDMA 456 and
Strokes Strokes Double acting. Min. stroke with 2 sensors Ø Single acting. Single acting
S version Type... Standards... Cushioning... Rated temperature... Fluid... Working pressure... Proximity switch... Mounting and accessories... Materials... Single and double acting pneumatic microcylinders,
STANDARDISED MOUNTINGS
for PS / PLS / PC cylinders conforming ISO 15552-FNOR-DIN (PS-PLS) ISO 21287 (PC) standards Series 434 MOUNTINGS CONFORMING WITH ISO 21287 - ISO 15552 - FNOR NF ISO 15552 - DIN ISO 15552 STNDRDS B C pplications
Series CP95. Profile Design ISO/VDMA Air Cylinder. Increased kinetic energy absorption. Improved end of stroke cushion capacity
Profile Design ISO/VDMA Air Cylinder Series CP95 Improved end of stroke cushion capacity Piston rod lurching has been eliminated at the end of stroke positions by means of a floating seal mechanism. Increased
10/97 N Our policy is one of continued research and development. We therefore reserve the right
ISO Cylinders Magnetic Piston Double Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Buffer and adjustable cushioned models Supplied complete with nose mounting
ELECTRIC CYLINDERS SERIES ELEKTRO ACTUATORS
ELECTRIC CYLINDERS SERIES ELEKTRO 1 ELECTRIC CYLINDER SERIES ELEKTRO ISO 15552 An electric cylinder with a connection interface in accordance with in-line version ISO 15552. The piston rod extension is
Features. Specification. Model. Acting type. Tube I.D. (mm) 20,25 32,40,50,63,80,100. Port size M5 0.8 G1/8. Proof pressure.
series Table for standard stroke Stroke (mm) ø20,25 5,10,15,20,25,30,40,50,60,80,100,200 ø32,40 5,10,15,20,25,30,40,50,60,80,100,200,300 ø50,63 10,15,20,25,30,40,50,60,80,100,200,300,400 ø80,100 15,20,25,30,40,50,60,80,100,200,300,400,500
PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M
PA/181000, PA/181000/M M/50 switches can be mounted flush with the profile Conforms to DIN ISO 6431 and VDMA 24562 part 1 Mountings conform to DIN ISO 6431, VDMA 24562 part 2 and NFE 49-003-1 Polyurethane
LPRA/182000/M Double acting profile cylinders Ø mm
Double acting profile cylinders 32... 125 mm High performance, stability and reliability M/50 switches (solid state) can be mounted flush with the profile Cylinders and mountings conform to ISO 15552 (ISO
PRA/822000/M, PRA/ Smoothline cylinder Magnetic or non-magnetic piston, double acting
P/822000/M, P/822000 Smoothline cylinder > 32... 00 mm > Cylinder and mounting conform to ISO 5552 > eed or solid state switches can be mounted flush with the profile barrel > lternative air ports as standard
PVA/182000, PVA/182000/M
Smooth Line cylinders with or without integrated switches Double acting Ø 3... 100 mm Smooth and spherical profile design with concealed tie rods Special polyurethane wiper seal Body sealing conforms to
Guide blocks for ISO/VDMA cylinders
Actuators Guide blocks or ISO/VDMA cylinders QA/8/51/ QA/8/61/ QA/8/81/ (long coupling) QA/8/85/ (short coupling) Ø 32 to 1 mm QA/8/61/ QA/8/51/ Conorms to ISO 6431, VDMA 24562 and NFE 49 3 1 Ensures protection
TELESCOPIC CYLINDERS ø mm Series RT
TELESCOPIC CYLINDERS 25 63 mm Series RT The overall dimensions are one of the most imporant aspects: in comparison with a traditional ISO cylinder of the same a reduction in size of approx. 45% (with a
Stainless Steel Cylinders DIN ISO 6431 and VDMA Bores from 32 to 200 mm
Bores from 32 to 200 mm Double acting Standard executions Version Symbol TYP MAGNTIC STANDARD AMX STAINLSS STL For the magnetic reed switches type ASV see from page 1.110.1. For coupling cylinders/reed
Stainless Steel Cylinders Acid and Corrosion Resistant
Stainless Steel Cylinders Acid and Corrosion Resistant Subject to change 133 Stainless Steel Cylinders Contents Stainless Steel Double-Acting Cylinders per ISO 6432 Bores 12 to 25 mm Type CRDSNU... 137
PRA/182000, PRA/182000/M
Profile cylinders conforms to ISO 15552 Non-magnetic and magnetic piston Double acting Ø 32 to 125 mm High performance, stability and reliability M/50 switches can be mounted flush with the profile Cylinders
Series 83. Stainless Steel Mini Cylinder
Stainless Steel Mini Cylinder Magnet included in 7/8 and 1-1/4 bore only in double acting cylinder THEORETICAL CYLINDER FORCE (LBS). Operating Pressures (PSI) Size Action 25 50 75 100 125 150 3/4" Out
Medium Duty 1.5 ~ 4 Bore 12 Different NFPA Mounting Options Non-Rotating Option Tandem Cylinder Option Auto Switch Capable
N304 Air Cylinder NCA1 Series NFPA Interchangeable Medium Duty 1.5 ~ 4 Bore 12 Different NFPA Mounting Options Non-Rotating Option Tandem Cylinder Option Auto Switch Capable NFPA Interchangable Air Cylinder
TECHNICAL CHARACTERISTICS
2 or 3-stage telescopic pneumatic cylinder Considering its high technological contents, this cylinder series represents without doubt the product with the highest degree of technical research and evolution
PRA/182000, PRA/182000/M
Profile barrel with concealed tie rods Pneumatic Profile Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Double Acting Ø 32 to 125 mm M/50 Switches can be mounted flush
P1D-B Pneumatic Cylinders
P1D-B Pneumatic Cylinders According to ISO 15552 P1D-B series. This series features a profile design and is the basic ISO cylinder for simple applications where no special options are required. This series
Our policy is one of continued research and development. We therefore reserve the right 1/98 N
ISO Cylinders Magnetic Piston Single Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Nose mounting nut and piston rod locknut as standard Technical Data Medium:
V160C. Mould Hydraulic Systems. Hydraulic cylinders-iso 6020/2 compact 160 bar V160C
V160C Mould Hydraulic Systems Hydraulic cylinders-iso 6020/2 compact 160 bar V160C V160Ccat.GB01-2006 Hydraulic cylinders-iso 1 2 Chrome-plated steel rod, hardened or tempered and polished. Thickness of
DIE DESIGN AND CONSTRUCTION SPECIFICATIONS STAMPING - EUROPE METRIC AIR CYLINDER
METRIC AIR CYLINDER WITH STAINLESS STEEL PISTON ROD, ALUMINIUM CYLINDER TUBE AND WITHOUT MAGNETIC PISTON THIS STANDARD REFERS TO THE DIMENSIONS REQUIRED FOR INTERCHANGEABILITY FOR SINGLE ROD, DOUBLE ACTING
Tube connection Ambient temperature range Medium temperature range. T min C +80. C T max. max. Weight (mass) kg See table
Cylinder Ø32-125 mm with blocking device Series DZB... Blocking reverse stroke Series DZBA... Blocking forward stroke Mountings to ISO 15552 (ISO 6431) Special versions: according to CETOP RP 53 P (Piston
ISO CYLINDERS Ø ACTUATORS
ISO 15552 CYLINDERS Ø 250-320 1 Cylinders made to ISO 15552 available in various versions and with a wide range of accessories: double-acting single-or through-rod with or without cushioning configuration