FULL COLOR TAB #1 TA 7

Transcription

1 FULL COLOR TAB #1 TA 7

2 TA - How to Order Floating Rod Bushing SELF ALIGNMENT FEATURE Rod Bushing is designed to float.00 to improve bearing surface alignment. SERIES TA (NFPA) CYLINDER Reduces cylinder drag and erratic operation Reduces cylinder wear Provides a minimum of 5% longer life than fixed rod bushing designs HEAVY-DUTY DESIGN FOR RELIABLE, CONSISTENT OPERATION FLOATING BUSHING Precision machined from 150,000 PSI rated graphite-filled cast iron and PTFE coated to reduce friction and extend cycle life. Bushing design traps lubrication in effective bearing area. HEAD, CAP & RETAINER Precision machined from high strength 6061-T6 aluminum alloy. Black anodized for corrosion resistance. CYLINDER TUBE Precision machined from T683 high tensile aluminum alloy and hard coat to 60 Rc for wear resistance and extended cycle life. PISTON Precision machined from high yield, polished and hard chrome plated steel. PISTON & SEALS Heavy lip design Carboxilated Nitrile construction. Seals are pressure activated and wear-compensating for long life (self-lubricating material). WIPER Abrasion resistant urethane provides aggressive wiping action in all environments. External lip design prevents debris from entering cylinder. PISTON Precision machined from 6061-T651 alloy aluminum, provides an excellent bearing surface for extended cylinder life TIE S Pre-stressed high carbon steel tie rod construction eliminates axial loading of cylinder tube and maintains compression on tube and end seals. PERMANENT LUBRICATION Permanently lubricated with Magnalube-G PTFE based grease on all internal components. This is a non-migratory type high performance grease providing outstanding service life. No additional lubrication is required. CUSHIONS Floating cushion seal designed for maximum cushion performance, quick return stroke break-away and extended life ( H & C). CUSHION ADJUSTMENT NEEDLE Adjustable steel needle design has fine thread metering and is positively captured to prevent needle ejection during adjustment. PISTON WEAR BAND - 90% Virgin PTFE and 10% Polyphenylene Sulfide-filled wear band; extremely low wear rate. PISTON MAGNET For TRD magnetically operated reed and solid state switches (Option MPR). OPERATING PRESSURE 50 PSI AIR (17 BAR) OPERATING TEMPERATURE Carboxilated Nitrile: -0 F to 00 F (-9 C to 93 C ) Fluorocarbon: 0 F to 400 F (-18 C to 04 C ) Performance : ST Stop tubes are used to reduce rod bearing and piston stress (refer to pages 01-0 for cylinder design guidance). MA Micro-Adjust provides a precision adjustment on the cylinder extend stroke, providing quick and accurate cylinder positioning to reduce set-up time. SSA Stainless steel piston rod, tie rods, nuts and fasteners provide corrosion resistance in outdoor applications and wet environments. LF Low friction seals reduce breakaway and running friction. Effective at all operating pressures. 8

3 TA HOW TO ORDER: SERIES TA (STANDARD CYLINDER) TA - MF1 - x 10 - HC - MPR SERIES 50 PSI AIR NFPA MOUNTS MF1 FRONT FLANGE ( - ) MF REAR FLANGE ( - ) ME3 FRONT MOUNTING HOLES ( - 1 ) ME4 REAR MOUNTING HOLES ( - 1 ) MP1 REAR PIVOT CLEVIS ( - 1 ) MP REAR PIVOT CLEVIS ( - ) MP4 REAR PIVOT EYE ( - ) MS1 FRONT & REAR END ANGLE ( - ) MS SIDE LUG ( - ) MS4 BOTTOM TAPPED HOLES ( - 1 ) MT1 FRONT TRUNNION ( - ) MT REAR TRUNNION ( - ) MT4 INTERMEDIATE TRUNNION ( - ) MX0 NO MOUNT ( - 1 ) MX1 EXTENDED TIE S - HEAD & CAP ( -1 ) MX EXTENDED TIE S (CAP) ( - 1 ) MX3 EXTENDED TIE S (HEAD) ( - 1 ) About our Part Number System Simple, easy to understand No excessive codes! Eliminates mistakes when ordering Example: A Bore by 10 Stroke NFPA cylinder, Front Flange Mount, Head & Cap Cushions, Magnetic Piston for. Part Number: TA-MF1- x 10-HC-MPR STANDARD PORT AND CUSHION ADJUSTMENT POSITIONS Ports - Positions 1 and 5 Cushion Adjustment - Positions and 6 Specify Non-Standard Positions When Ordering MF1 MF 1 STROKE 0 TO 10 MADE-TO- ORDER STYLE SINGLE (LEAVE BLANK) D = DOUBLE END ME3 H LH ELH C LC ELC FCH FCC CUSHIONS HEAD CUSHION POSITION IS STANDARD SPECIFY FOR POSITIONS: 1, 3 & 4 LONG HEAD CUSHION POSITION IS STANDARD SPECIFY FOR POSITIONS: 1, 3 & 4 EXTRA LONG HEAD CUSHION POSITION IS STANDARD SPECIFY FOR POSITIONS: 1, 3 & 4 CAP CUSHION POSITION 6 IS STANDARD SPECIFY FOR POSITIONS: 5, 7 & 8 LONG CAP CUSHION POSITION 6 IS STANDARD SPECIFY FOR POSITIONS: 5, 7 & 8 EXTRA LONG CAP CUSHION POSITION 6 IS STANDARD SPECIFY FOR POSITIONS: 5, 7 & 8 FIXED CUSHIONS FIXED HEAD CUSHION (NON-ADJUSTABLE, NO ADJUSTMENT NEEDLE) FIXED CAP CUSHION (NON-ADJUSTABLE, NO ADJUSTMENT NEEDLE) FIXED HEAD AND CAP CUSHION FC (NON-ADJUSTABLE, NO ADJUSTMENT NEEDLE) Note: L AND EL CUSHION OPTIONS CAN BE ORDERED AS FIXED CUSHIONS. Example: FCLH, FCELH NFPA MOUNTS ME4 å X X å OPTIONS ADDS LENGTH TO CYLINDER - SEE OPTION LENGTH ADDER CHART BELOW. A = EXTENDED PISTON THREAD (EXAMPLE: A = ) AS ADJUSTABLE STROKE - RETRACT (SPECIFY LENGTH, EXAMPLE: AS = 4 ) A / O AIR / OIL PISTON X B.50 URETHANE BUMPER BOTH ENDS X BC.50 URETHANE BUMPER CAP ONLY X BH.50 URETHANE BUMPER HEAD ONLY BP BUMPER PISTON SEALS ( - 8 ) BSP BSP PORTS (SPECIFY SIZE, EXAMPLE: BSP =.50 ) C = EXTENDED PISTON (EXAMPLE: IF C = 0.50, THEN 1 EXTENSION IS C = ) EN ELECTROLESS NICKEL PLATED KK LARGE MALE THREAD KK3 FEMALE THREAD KK3S STUDDED PISTON (KK3 WITH STUD, LOCTITE IN PLACE) KK4 FULL DIAMETER MALE THREAD KK5 BLANK END (NO THREADS, A = 0 ) LF LOW FRICTION SEALS MA MICRO-ADJUST (1 MAX STROKE) AVAILABLE ON DOUBLE END MODELS MAB MICRO-ADJUST W/ SOUND DAMPENING BUMPER (1 MAX STROKE) MPR MAGNETIC PISTON FOR REED OR SOLID STATE SWITCHES - MODELS: R10, R10P, RAC, RHT & MSS MS METALLIC SCRAPER (BRASS CONSTRUCTION) NR NON-ROTATING OP OPTIONAL PORT LOCATION (EXAMPLE: 3 & 7) OS OVERSIZE DIAMETER (SPECIFY SIZE, EXAMPLE: OS = ) SAE SAE PORTS (SPECIFY SIZE, EXAMPLE: SAE #10) X SE SPRING EXTEND (,, ) X SR SPRING RETURN (,, ) SSA STAINLESS STEEL PISTON, TIE S, NUTS & FASTENERS SSF STAINLESS STEEL FASTENERS SSN STAINLESS STEEL TIE NUTS SSR STAINLESS STEEL PISTON SST STAINLESS STEEL TIE S X ST STOP TUBE - SPECIFY STOP TUBE LENGTH (IN INCHES) SPECIFY STROKE AS ES (EFFECTIVE STROKE) (EXAMPLE: TA MS4 X 4ES-ST=3) TMS STEEL CYLINDER TUBE, BLACK EPOXY PAINT FINISH TH 400 PSI HYDRAULIC NON-SHOCK VS FLUOROCARBON SEALS XX SPECIAL VARIATION (SPECIFY) Note: Refer to for specifications. OPTION LENGTH ADDER (ADD TO CATALOG BASIC OVERALL LENGTH DIMENSIONS) OPTION ST* (STOP TUBE) B BC BH ELC ELH SE SR EXAMPLE: ST= REFER TO PAGE FOR LENGTH ADDERS AND AVAILABLE SIZES AND STROKES *The desired Stop Tube length adds directly to the overall cylinder length. MP1 MP TA - How to Order - MP4 - MS1-1 MS -1 MS4-1 MT1 - MT - - MT MX MX MX - -1 MX3-9

4 TA - How to Order SERIES TA DIMENSIONS: BASIC CYLINDER (NO MOUNT) About Rod End Styles Style 1 Male Rod End is STANDARD Other NFPA styles can be specified (see chart). Need a rod end not listed? NO PROBLEM! Each Piston Rod is made-to-order and does not delay shipment. Coarse UNC threads, Metric threads or just plain rod ends are common. Thread lengths are also made-to-order (Specify: A =Length). NEED SOMETHING NOT LISTED? Just send us a sketch. In most cases, quotes are turned around in one day! STYLE 1 & KK1 & KK PISTON END STYLES STYLE 3 KK3 STYLE 4 KK4 STYLE 5 KK5 EASY FLIP OUT PAGE FOR REFERENCE,,,, & 1 STANDARD OPTIONAL MM Style 1 - Male Style - Male Style 3 - Female Style 4 - Male Style 5 - Blank DIAMETER KK1 A KK A KK3 A KK4 A KK5 C V 7/ / / / No Threads Oversize 3/ / / No Threads / / / No Threads Oversize / / No Threads / / No Threads Oversize 1 1/ / / /4-1 0 No Threads Standard 1 1/ / / /4-1 0 No Threads Oversize 1 1/ / / No Threads Standard 1 1/ / / No Threads Oversize 1 7/ / / / No Threads BASIC DIMENSIONS MX0 STANDARD & OVERSIZE S DIAMETER A B C E EE F G J K KK LB MM P R RM V Y ZB / SQ Oversize / / HEX Oversize / SQ / HEX Oversize / SQ / DIA Oversize SQ / DIA Oversize DIA / DIA Oversize DIA DIA Oversize / DIA Oversize / Standard / DIA Oversize / -1 0 DIA Standard / DIA. 0 Oversize / TA SERIES BASE DIMENSIONS FLIP-OUT (PAGE 10)

5 EASY FLIP OUT PAGE FOR REFERENCE SERIES TA DIMENSIONS: BASIC CYLINDER (NO MOUNT) About Rod End Styles Style 1 Male Rod End is STANDARD Other NFPA Styles can be specified (see chart). Need a rod end not listed? NO PROBLEM! Each Piston Rod is made-to-order and does not delay shipment. Coarse UNC threads, Metric threads or just plain rod ends are common. Thread lengths are also made-to-order (Specify: A =Length). NEED SOMETHING NOT LISTED? Just send us a sketch. In most cases, quotes are turned around in one day! STYLE 1 & KK1 & KK PISTON END STYLES STYLE 3 KK3 STYLE 4 KK4 STYLE 5 KK5,,,, & 1 STANDARD OPTIONAL MM Style 1 - Male Style - Male Style 3 - Female Style 4 - Male Style 5 - Blank DIAMETER KK1 A KK A KK3 A KK4 A KK5 C V 7/ / / / No Threads Oversize 3/ / / No Threads / / / No Threads Oversize / / No Threads / / No Threads Oversize 1 1/ / / /4-1 0 No Threads Standard 1 1/ / / /4-1 0 No Threads Oversize 1 1/ / / No Threads Standard 1 1/ / / No Threads Oversize 1 7/ / / / No Threads BASIC DIMENSIONS MX0 STANDARD & OVERSIZE S DIAMETER A B C E EE F G J K KK LB MM P R RM V Y ZB / SQ Oversize / / HEX Oversize / SQ / HEX Oversize / SQ / DIA Oversize SQ / DIA Oversize DIA / DIA Oversize DIA DIA Oversize / DIA Oversize / Standard / DIA Oversize / -1 0 DIA Standard / DIA. 0 Oversize / TA SERIES BASE DIMENSIONS FLIP-OUT (PAGE 10)

6 TA - How to Order SERIES TA DIMENSIONS: PIVOT MOUNTS - S HEX NUTS -1 S EXTRUDED MP1 MOUNT (EXTRUDED: - S, WELDMENT: & 1 S) IRON CASTING MP1 MOUNT (OPTIONAL)** * * 1 MP/MP4 MP1, MP CLEVIS AND MP4 EYE MOUNT DIMENSIONS ACCESSORIES EYE CLEVIS CLEVIS BRACKET BRKT DIAMETER CB CD CW FL K L M XC XD CLEVIS EYE PIN (FOR MP1) (FOR MP4) RC437 RE437 CP N/A Oversize RC750 RE750 CP750 EB500 CB RC437 RE437 CP N/A Oversize RC750 RE750 CP750 EB500 CB RC437 RE437 CP N/A Oversize RC750 RE750 CP750 EB500 CB RC750 RE750 CP Oversize RC1000 RE1000 CP1000 EB750 CB RC750 RE750 CP Oversize RC1000 RE1000 CP1000 EB750 CB RC750 RE750 CP Oversize RC1000 RE1000 CP1000 EB750 CB RC1000 RE1000 CP Oversize RC150 RE150 CP1375 EB1000 CB RC1000 RE1000 CP N/A N/A Oversize RC150 RE150 CP1375 EB1000 CB Standard RC150 RE150 CP1375 EB1375 CB N/A N/A 0 Oversize RC1500 RE1500 CP1750 EB1750 CB Standard RC1500 RE1500 CP N/A N/A 0 Oversize RC1875 N/A CP000 EB1750 CB1750 Clevis pins are provided with pivot mounts. *MP4 - bores are 5-7 day delivery. For dimensions not shown, see page 10. MP MOUNT IRON CASTING: - S 11 MP4 MOUNT IRON CASTING: - S WELDMENT: - S* ** Extruded MP1 mounts are standard ( - bores). Cast Iron removable mounts are optional, and must be requested when ordering ( - bores). Specify CAST MP1 when ordering.

7 SERIES TA DIMENSIONS: PIVOT MOUNTS TA - How to Order MT1 / MT MT1 HEAD TRUNNION AND MT CAP TRUNNION MOUNT DIMENSIONS ACCESSORIES ADD STROKE DIAMETER E TD TL UT XG XJ CLEVIS EYE CLEVIS PIN RC437 RE437 CP Oversize N/A* RC750 RE750 CP RC437 RE437 CP Oversize RC750 RE750 CP RC437 RE437 CP Oversize RC750 RE750 CP RC750 RE750 CP Oversize RC1000 RE1000 CP RC750 RE750 CP Oversize RC1000 RE1000 CP RC750 RE750 CP Oversize RC1000 RE1000 CP RC1000 RE1000 CP Oversize RC150 RE150 CP RC1000 RE1000 CP Oversize RC150 RE150 CP1375 *No oversize rod available on bore MT1. For dimensions not shown, see page 10. Note: MT1 and MT Trunnions are bolt on, non-removable design. Optional: One-piece solid steel trunnion available. MT1, MT, MT4 STANDARD CUSHION LOCATIONS MOUNT HEAD CUSHION CAP CUSHION MT1 3 6 MT 7 MT4 6 Note: Ports or cushions cannot be on same side as MT1 & MT Trunnions. MT4 Note: MT4 Trunnions and Intermediate Section are one-piece steel construction. MT4 INTERMEDIATE TRUNNION MOUNT DIMENSIONS BD EB TD TL TM UM XI CUSTOMER TO SPECIFY

8 TA - How to Order SERIES TA DIMENSIONS: TIE & FLANGE MOUNTS TIE EXTENDED MX1, MX & MX3 MOUNT DIMENSIONS DIAMETER AA BB DD FH R Oversize / Oversize / Oversize / Oversize / Oversize / *MX1 & MX3 have full square bushing retainer on - bores, round retainers on - 1 bores. **BB dimension from face of head. For dimensions not shown, see page 10. TIE EXTENDED MX1, MX & MX3 MOUNT DIMENSIONS DIAMETER AA BB DD FH R Oversize / Oversize / Oversize ** 5/ * Oversize 0.65* ** 3/ Oversize 0.750* Standard 0 Oversize ** 3/ * S - S - 1 S MF1, MF FLANGE & ME3, ME4 CAP MOUNT DIMENSIONS DIAMETER E F FB FH R RM TE TF UF W ZF Oversize Oversize Oversize Oversize Oversize For dimensions not shown, see page S MF1, MF FLANGE & ME3, ME4 CAP MOUNT DIMENSIONS DIAMETER E F FB FH R RM TE TF UF W ZF Oversize Oversize N/A N/A N/A N/A Oversize Standard N/A N/A N/A N/A 0 Oversize Standard N/A N/A N/A N/A 0 Oversize

9 SERIES TA DIMENSIONS: BASE MOUNTS TA - How to Order MS1 ANGLE MOUNT DIMENSIONS ADD STROKE DIAMETER AB AH AL AO AT FH S SA XA Oversize Oversize Oversize Oversize Oversize Oversize Oversize * Oversize *3.50 diameter round retainer on bore (MS1 BRACKET BOLTED DIRECTLY TO HEAD). ** bore has four (4) AB diameter holes. MS SIDE LUG MOUNT DIMENSIONS DIAMETER SB SH ST SU SW SZ TS US XS Oversize Oversize Oversize Oversize Oversize Oversize Oversize Oversize.563 For dimensions not shown, see page ADD STROKE SS

10 TA - How to Order SERIES TA DIMENSIONS: BASE MOUNTS MS4 BOTTOM TAPPED MOUNT DIMENSIONS DIAMETER E/ NT TK TN XT / Oversize / Oversize / Oversize / Oversize Standard / Oversize / Oversize / Oversize / Oversize Standard Oversize Standard Oversize For dimensions not shown, see page 10. COMBINATION MOUNTS Cylinders can be ordered with a combination of mounts for added design flexibility. ADD STROKE SN How to Order: Combination mount part numbers can be constructed by adding a dash (-) in between the desired mounts in the part number. Example: Bore TA Series cylinder with 1 Stroke, Head and Cap Cushions, Magnetic Piston for Reed and having a MS4 and MF1 Mount: Part Number: TA-MS4-MF1-5 x 1-HC-MPR (FM-MF1-MF-MT4D) 15

11 SERIES TA DIMENSIONS: DOUBLE END Benefits Standard and Oversize Piston Rods available. Full range of Standard. Durable design. Full Rod Bearing at each end of cylinder. Can be provided with Hollow Piston Rods (gun-drilled through to your size requirements). Can be used in adjustable extend stroke applications by adding a stop collar on one rod end or option MA (refer to ). STANDARD PORT AND CUSHION ADJUSTMENT POSITIONS Ports - Positions 1 and 5 Cushion Adjustment - Positions and 6 Specify Non-Standard Positions When Ordering SERIES TA DIMENSIONS: DOUBLE END BASE MOUNTS TA - How to Order MS1D ANGLE MOUNT DIMENSIONS ADD STROKE DIAMETER AB AH AL AO AT FH S SAD XAD Oversize Oversize Oversize Oversize Oversize Oversize Oversize * Oversize *3.50 diameter round retainer on bore (MS1 BRACKETS BOLTED DIRECTLY TO HEAD). 16

12 TA - How to Order About Rod End Styles SERIES TA DIMENSIONS: DOUBLE END Style 1 Male Rod End is STANDARD Other NFPA Styles can be specified (see chart). Need a rod end not listed? NO PROBLEM! Each Piston Rod is made-to-order and does not delay shipment. Coarse UNC threads, Metric threads or just plain rod ends are common. Thread lengths are also made-to-order (Specify: A =Length). NEED SOMETHING NOT LISTED? Just send us a sketch. In most cases, quotes are turned around in one day! STYLE 1 & KK1 & KK PISTON END STYLES STYLE 3 KK3 STYLE 4 KK4 STYLE 5 KK5 EASY FLIP OUT PAGE FOR REFERENCE,,,, & 1 STANDARD OPTIONAL MM Style 1 - Male Style - Male Style 3 - Female Style 4 - Male Style 5 - Blank DIAMETER KK1 A KK A KK3 A KK4 A KK5 C V 7/ / / / No Threads Oversize 3/ / / No Threads / / / No Threads Oversize / / No Threads / / No Threads Oversize 1 1/ / / /4-1 0 No Threads Standard 1 1/ / / /4-1 0 No Threads Oversize 1 1/ / / No Threads Standard 1 1/ / / No Threads Oversize 1 7/ / / / No Threads DOUBLE END DIMENSIONS: MX0D (NO MOUNT) 1 DOUBLE END BASIC DIMENSIONS MX0D STANDARD & OVERSIZE S DIAMETER A B C E EE F G K KK LD MM P R RM V Y ZM / SQ Oversize / / HEX Oversize / SQ / HEX Oversize / SQ / DIA Oversize SQ / DIA Oversize DIA / DIA Oversize DIA DIA Oversize / DIA Oversize / Standard / DIA Oversize / -1 0 DIA Standard / DIA. 0 Oversize / TA SERIES DOUBLE END BASE DIMENSIONS FLIP-OUT (PAGE 17)

13 EASY FLIP OUT PAGE FOR REFERENCE SERIES TA DIMENSIONS: DOUBLE END About Rod End Styles Style 1 Male Rod End is STANDARD Other NFPA Styles can be specified (see chart). Need a rod end not listed? NO PROBLEM! Each Piston Rod is made-to-order and does not delay shipment. Coarse UNC threads, Metric threads or just plain rod ends are common. Thread lengths are also made-to-order (Specify: A =Length). NEED SOMETHING NOT LISTED? Just send us a sketch. In most cases, quotes are turned around in one day! STYLE 1 & KK1 & KK PISTON END STYLES STYLE 3 KK3 STYLE 4 KK4 STYLE 5 KK5,,,, & 1 STANDARD OPTIONAL MM Style 1 - Male Style - Male Style 3 - Female Style 4 - Male Style 5 - Blank DIAMETER KK1 A KK A KK3 A KK4 A KK5 C V 7/ / / / No Threads Oversize 3/ / / No Threads / / / No Threads Oversize / / No Threads / / No Threads Oversize 1 1/ / / /4-1 0 No Threads Standard 1 1/ / / /4-1 0 No Threads Oversize 1 1/ / / No Threads Standard 1 1/ / / No Threads Oversize 1 7/ / / / No Threads DOUBLE END DIMENSIONS: MX0D (NO MOUNT) 1 DOUBLE END BASIC DIMENSIONS MX0D STANDARD & OVERSIZE S DIAMETER A B C E EE F G K KK LD MM P R RM V Y ZM / SQ Oversize / / HEX Oversize / SQ / HEX Oversize / SQ / DIA Oversize SQ / DIA Oversize DIA / DIA Oversize DIA DIA Oversize / DIA Oversize / Standard / DIA Oversize / -1 0 DIA Standard / DIA. 0 Oversize / TA SERIES DOUBLE END BASE DIMENSIONS FLIP-OUT (PAGE 17)

14 TA - How to Order SERIES TA DIMENSIONS: DOUBLE END BASE MOUNTS DOUBLE END MSD SIDE LUG MOUNT DIMENSIONS DIAMETER SB SH ST SU SW TS US XS Oversize Oversize Oversize Oversize Oversize Oversize Oversize Oversize.563 For dimensions not shown, see page 17. ADD STROKE SSD DOUBLE END MS4D BOTTOM TAPPED MOUNT DIMENSIONS DIAMETER E/ NT TK TN XT / Oversize / Oversize / Oversize / Oversize / Oversize / Oversize / Oversize / Oversize Standard Oversize Standard Oversize For dimensions not shown, see page ADD STROKE SN

15 SERIES TA DIMENSIONS: DOUBLE END TIE & FLANGE MOUNTS TA - How to Order TIE EXTENDED MX1D & MX3D MOUNT DIMENSIONS DIAMETER AA BB DD FH R Oversize / Oversize / Oversize / Oversize / Oversize / *Full square bushing retainer on - bores, round retainers on - 1 bores. ** BB dimension from head on, & 1 bores. TIE EXTENDED MX1D & MX3D MOUNT DIMENSIONS DIAMETER AA BB DD FH R Oversize / Oversize / Oversize ** 5/ * Oversize 0.65* ** 3/ Oversize 0.750* Standard 0 Oversize ** 3/ * S - 1 S ONLY MF1D FLANGE & ME3D CAP MOUNT DIMENSIONS DIAMETER E FB FH R RM TE TF UF W Oversize Oversize Oversize Oversize Oversize For dimensions not shown, see page MF1D FLANGE & ME3D CAP MOUNT DIMENSIONS DIAMETER E FB FH R RM TE TF UF W Oversize Oversize N/A N/A N/A N/A Oversize Standard N/A N/A N/A N/A Oversize Standard N/A N/A N/A N/A 0 0 Oversize.50

16 SERIES TA DIMENSIONS: DOUBLE END PIVOT MOUNTS Note: MT1D Trunnions are bolt on, non-removable design. DOUBLE END MT1D HEAD TRUNNION MOUNT DIMENSIONS DIAMETER E TD TL UT XG N/A* N/A Oversize Oversize Oversize Oversize Oversize Oversize Oversize.875 *No oversize rod available on bore MT1D. For dimensions not shown, see page 17. TA - How to Order Note: MT4D Trunnions and Intermediate Section are one-piece steel construction. DOUBLE END MT4D INTERMEDIATE TRUNNION MOUNT DIMENSIONS BD EB TD TL TM UM XI MT1D, MT4D STANDARD CUSHION LOCATIONS MOUNT HEAD CUSHION CAP CUSHION MT1D 3 6 MT4D 6 Note: Ports or cushions cannot be on same side as MT1D Trunnions CUSTOMER TO SPECIFY 0