Linear guide table provides long stroke. Table rigidity is constant throughout entire stroke. Table for mounting of workpiece

Transcription

1 ir Slide Table MX Series ø, ø2, ø, ø, ø2 RoS inear guide table provides long stroke. Table rigidity is constant throughout entire stroke. ong stroke (Max. 00 mm) inear guide provides long stroke, and it obtains smooth operation without vibration. MX MX2 MX MX MX2 Stroke Shock absorber Dual piston rod Slim design provides 2 times the force of standard cylinder. MX: ø x 2 MX2: ø2 x 2 MX: ø x 2 MX: ø x 2 MX2: ø2 x 2 MX MXS MXQ MXQ MX MX MXJ MXP MX MTS Stroke adjuster Piping, iring Piping is possible from 2 directions. Can pipe and wire switches from the same surface. uto switch can be attached to either side of body. ateral piping/wiring Table for mounting of workpiece ody mounting Machining of positioning hole Thread for body mounting 2 mounting types (ody tapped, Through-hole) are available. ody tapped xial piping ody through-hole 2 D- -X

2 MX Series Selection oad eight Maximum oad Mass (kg) 2 MX. MX2 4 4 MX 2. MX 2.. MX2.2 Note) No need to consider this load factor in the case of using perpendicularly in a vertical position. Piston speed (mm/s) raph () Moment Mp/Mep (Pitch moment) My/Mey (aw moment) Mr (Roll moment) 0 llowable Moment (Static moment/dynamic moment) (N m) Pitch moment aw moment Roll moment Mp/Mep My/Mey Mr 2 MX MX2 4 MX MX MX verage operating speed (mm/s) verage operating speed (mm/s) raph (2) raph () Static Moment Moment generated by the workpiece weight even when the cylinder is stopped 2 Pitch moment aw moment Roll moment : Moment center position Mp = x 9. ( + ) distance compensation My = x 9. (2 + ) Mr = x 9. ( + C) amount : Moment center position MX 9 distance compensation C: Moment center position MX2 4 amount distance compensation amount MX MX Mr MX2 9 My Mp Selection Caution Operate loads within the range of the operating limits. Select the model from the maximum allowable load and allowable moment. or details, refer to the following selection procedures. hen actuator is used outside of operating limit, eccentric loads on the guide in excess, will cause vibration on guide, inaccuracy and shorten its life. Mp 2 MX MX2 MX MX MX2 4 2 My Maximum moment (N m) MX MX2 MX MX MX If intermediate stops by external stopper are done, avoid ejection. If ejection occurs, it may cause damage. In the case slide table is stopped at intermediate positions by the external stopper then forwarded to the front, after slide table is returned to the back for just a moment to retract the stopper, supply pressure to the opposite port to operate slide table. Do not use it in such a way that excessive external force or impact force could work on it. This could result in damage. Maximum allowable load and allowable moment will vary depending on workpiece mounting methods, mounting orientation and operating speed. In making a determination of usability, the load mass and moment should be within the operating range of the graph with respect to operating conditions and the total (Σ n) of the load factors ( n) for load mass and moment should not exceed. 22 Σ n = oad () Maximum load mass (max) + Static moment (M) llowable static moment (Mmax) max, Mmax and Memax values are according to graph (), (2) and () below. 2: Moment center position distance compensation amount MX MX2 MX MX MX2 MX2 MX MX MX2 MX + 2: Moment center position distance compensation amount Dynamic moment (Me) llowable dynamic moment (Memax) < Maximum load mass (kg) Maximum moment (N m) MX MX2 MX MX MX2 MX MX2 MX MX MX2 4 2 C2: Moment center position distance compensation amount Mr MX2 MX MX MX2 MX MX2 MX MX MX2 MX C2 C

3 Selection MX Series Dynamic Moment Moment due to impact of load at end of stroke. Pitch moment e = δ =.4 Mep = / e x 9. ( + C) a verage load coefficient ) Correction factor (Reference value) e C: Moment center position e: quivalent mass for impact (kg) distance compensation δ : umper coefficient amount ith urethane bumper (standard) = 4/0 ith shock absorber = /0 : eight (kg) : Collision speed (mm/s) a: verage operating speed (mm/s) MX MX2 MX MX MX2 4 2 Selection Calculation or selection of a proper model, the items shown below should be within the operating range of the graph. urthermore, find load factors ( n) and make sure that their sum total (Σ n) does not exceed. Item oad factor n Note Max. load mass xamine. = /max max is maximum load mass at a. xamine Mp, My, and Mr. Static moment 2 = M/Mmax Mmax is the allowable moment for a. Dynamic moment = Me/Memax 2 amount MX MX2 MX MX MX2 <Operating conditions> Item oad factor n Note Max. load mass xamine. ind the value of max when a = 00 mm/s = /max from raph (). = / Note) No need to consider this load factor in = 0.4 the case of using perpendicularly in a vertical position. C (Define = 0.) Mep xamine Mep and Mey Memax is the allowable moment for. : Collision speed, a: verage speed C aw moment Mey = / e x 9. (2 + ) : Moment center position distance compensation e Cylinder: MX Cushion: Standard (Urethane bumper) Mounting: orizontal wall mounting verage operating speed: a = 00 [mm/s] eight: = [kg] = 0 [mm] 2 = 0 [mm] a Mey MX MXS MXQ MXQ MX MX MXJ MXP MX MTS Static moment Mr Mr = x 9. ( + C) = x 9. ( ) = 0. [N m] xamine Mr. (Mp, My values do not apply to this example.) +C 2 = Mr/Mrmax = 0./2 = 0.0 Mrmax value is from raph () at a = 00 mm/s. Dynamic moment Mey e 2+ Mey = / e x 9. (2 + ) =.4 a e = δ = 4/ =. [kg] Mey = / x. x 9. ( ) = 4. [N m] = Mey/Meymax = 4./4. = 0.4 xamine Mey. ind the equivalent mass for impact, e umper coefficient δ = 4/0 (ith urethane bumper) Meymax value is from raph (2) at =.4 a = 4 mm/s. e Mep +C Mep = / e x 9. ( + C) = /. x 9. ( ) =. [N m] ' = Mep/Mepmax =./4. = 0.24 xamine Mep. rom above formula e =. Mepmax value is from raph (2) at =.4 a = 4 mm/s. D- 2 -X

4 ir Slide Table MX Series RoS ow to Order MX 0 M9 ø ø2 ø ø ø2 Port thread type ø to ø Nil TN T M thread Rc NPT ø, ø2 ore size (Stroke ) 2, 0,, 0, 2, 0 0,, 0, 2, 0, 0, 2, 0,, 0 0, 2, 0,, 0, 22, 0, 2, 0,, 0, 22,, 2, 00 Number of auto switches Nil 2 pcs. S pc. n n pcs. Made to Order Refer to page 2 for details. uto switch Nil ithout auto switch (uilt-in magnet) or the applicable auto switch model, refer to the table below. Nil Option Standard (with urethane bumper) ith shock absorbers 2 pcs. pplicable uto Switches/Refer to pages 9 to 24 for the detailed specifications of auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indicator) ater resistant (2-color indicator) lectrical entry iring (Output) oad voltage DC C -wire (NPN),2 -wire (PNP) 2-wire 2 rommet -wire (NPN) es -wire (PNP) 2-wire -wire (NPN) 24,2 2,2 -wire (PNP) 2-wire 2 -wire es (quiv. to NPN) rommet None 2-wire or less uto switch model Perpendicular M9N M9P M9 M9N M9P M9 M9N M9P M In-line M9N M9P M9 M9N M9P M9 M9N M9P M ater resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. 2 m type lead wire is only applicable to D-9. ead wire length symbols: 0. m Nil m M m m Indicator light (xample) M9N (xample) M9NM (xample) M9N (xample) M9N Since there are other applicable auto switches than listed, refer to page 0 for details. or details about auto switches with pre-wired connector, refer to pages 92 and 9. uto switches are shipped together (not assembled). ead wire length (m) 0. (Nil) (M) () () Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC Solid state auto switches marked with are produced upon receipt of order. 24

5 ir Slide Table MX Series Made to Order Standard Stroke /eight (g) MX MX2 MX MX MX2 Made to Order: Individual Specifications (or details, refer to pages 02 and 0.) Specifications ore size Piping port size luid ction Operating pressure Proof pressure mbient and fluid temperature Cushion ubrication uto switch (Option) Operating speed range (verage operating speed) Note) Stroke length tolerance Stroke adjustment range Standard stroke MX MX2 MX MX MX2 ø x 2 ø2 x 2 ø x 2 ø x 2 ø2 x 2 ø or its ø or its ø2 or its ø2 or its ø or its ( equivalent) ( equivalent) ( equivalent) ( equivalent) ( equivalent) M x 0. Rc / ir Double acting 0. to 0. MPa.0 MPa to +0 C 0 to 00 mm/s Non-lube Reed auto switch Solid state auto switch (2-wire, -wire) 2-color indicator solid state auto switch (2-wire, -wire) + 0 mm One side: mm (oth sides: mm) None) verage operating speed: Speed that the stroke is divided by a period of time from starting the operation to reaching the end. <Operating direction> hen viewed from side with lateral ports. R: Right (OUT side) : eft (IN side) Theoretical Output Dual rod cylinder produces double the thrust of standard cylinder. oth ends urethane bumper (Standard) Shock absorber at both ends (Option) Symbol Specifications ore size Rod size Operating Piston area Operating pressure (MPa) -X PT grease direction (mm 2 ) X9 rease for food processing machines R X djusting bolt, long specification (djustment range: mm) X ithout built-in auto switch magnet R X9 luororubber seal X42 nti-corrosive specifications for guide unit -X4 PDM seal R R R Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2) dditional weight of option 00 Shock absorber R (N) MX MXS MXQ MXQ MX MX MXJ MXP MX MTS Moisture Control Tube IDK Series hen operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. or details, refer to the IDK series in the est Pneumatics No.. 2 D- -X

6 MX Series Table Deflection (Reference alues) The graphs below show the table displacement when the static moment load isapplied to the table. The graphs do not show the loadable mass Refer to the Selection for the loadable mass. Table displacement due to pitch moment load mount of displacement on when the load is applied at. = 0 mm Table displacement due to yaw moment load mount of displacement on when the load is applied at. = 0 mm Table displacement due to roll moment load mount of displacement on when the load is applied at. MX, MX2, MX 0.0 MX, MX2, MX 0.0 = 0 mm MX, MX2, MX 0. Table displacement amount MX MX2 MX Table displacement amount MX MX2 MX Table displacement amount MX MX2 MX oad (N) oad (N) oad (N) MX, MX2 0.0 MX, MX2 0.0 MX, MX2 0. Table displacement amount MX MX2 Table displacement amount MX MX2 Table displacement amount MX MX oad (N) oad (N) oad (N) 2

7 ir Slide Table MX Series Option Specifications Stopper olt ssembly Stopper bolt assembly can be ready for the following manner. Qty. needed for Parts to be Change of adjuster assembly stopper bolt assembly Changed Standard Semi-standard (-X) (Refer to the figure below.) Changing the stroke /o shock absorber 2 Replace adjustment range from mm to mm for one side ith shock absorber 4 Replace Changing to the one with shock absorber 2 dd Changing to the one with shock absorber Replace and stroke adjustment range of mm 4 dd Note ) hen only one side of stroke is changed, the quantity needed is the half of the above. Note 2) Shock absorber must be ordered separately. or the shock absorber model numbers, refer to page 2. Dimensions Shock absorber Urethane bumper side (Stopper side) ow to Order Stopper olt ssembly MX 2 X pplicable bore size 2 2 ø ø2 ø ø ø2 djustment range Nil mm Standard X mm Option Note ) The above model number is one adjuster bolt assembly only. Caution Precautions Mounting/djustment Do not operate within mm. The effectiveness of the shock absorber and urethane bumper will not be brought into full play, and could be adversely affected. ow to mount. Thread in the adjuster bolt from the direction of the arrow. 2. asten the lock nut from the direction of the arrow. MX MXS MXQ MXQ MX MX MXJ MXP MX MTS ød C M pplicable size MX MX2 MX MX MX2 MX-2 MX-2-X MX-22 MX-22-X MX-2 MX-2-X MX-2 MX-2-X MX-22 MX-22-X Stroke adjustable range C D 4 M M x 0. M x 0. M x M x.2 M x. Stopper bolt mm Stroke ock nut void operating within mm. The effectiveness of the shock absorber and urethane damper will not be brought into full play, and could be adversely affected. mm 2 D- -X

8 MX Series Option Specifications Shock bsorber Specifications Shock absorber model R00 -X2 R00 R0 R42 R -X2 -X2 -X2 -X2 pplicable slide table MX MX2 MX MX MX2 Max. absorbing energy (J) Stroke absorption Max. collision speed (m/sec) Max. operating frequency (cycle/min) Max. allowable thrust (N) to mbient temperature range ( ) to 0 xtended Spring force (N) Retracted eight (g) 2 0 Note) The shock absorber service life is different from that of the MX cylinder depending on operating conditions. Refer to the Specific Product Precautions for the replacement period. Caution Do not operate in such a state that the stopper blocks and stopper bolts on both sides are removed. Doing so could create shocks, which could loosen and cause damage. Stroke adjustment. Standard ock nut Urethane bumper Precautions djustment ow to Replace ow to Remove Shock adjuster block 2. Remove the shock absorbers. Shock adjuster block oosen the stopper bolt lock nut on side, insert a wrench in the direction of the arrow to adjust the stroke, and then tighten the lock nut. 2. ith shock absorber (Option) Shock absorber ow to Mount Recommended Tightening Torque MX MX2 MX MX MX2. oosen the shock absorber fixing screws. 2. Tighten the shock absorber fixing screws with the recommended torque shown in the table below. Shock absorber fixing thread size M x 4 M x 4 M x 4 M4 x M x In the case of MX-2, first take out the adjuster block, and then the shock absorber. Tighten the mounting bolt with the torque 0. N m when assembling the adjuster block Mount the shock absorbers. Insert to the end of the mounting hole of table. Recommended tightening exagon wrench torque (N m) width across flats Caution ock nut Stroke adjustment oosen the stopper bolt lock nut on side, insert a wrench in the direction of the arrow to adjust the stroke, and then tighten the lock nut. Stroke absorption adjustment for shock absorber oosen the stopper bolt lock nut on side, insert a wrench in the direction of the arrow to adjust the stroke, and then tighten the lock nut. Service ife and Replacement Period of Shock bsorber. llowable operating cycle under the specifications set in this catalog is shown below..2 million cycles R0 2 million cycles R0 to R Note) Specified service life (suitable replacement period) is the value at room temperature ( to 2 C). The period may vary depending on the temperature and other conditions. In some cases the absorber may need to be replaced before the allowable operating cycle above. 2

9 ir Slide Table MX Series Construction t e r y!!!4 w q!!2!!9 o u MX MXS MXQ MXQ MX MX MXJ MXP MX MTS Component Parts No. Description Material Note ody Table nd plate Stopper block Rail uide block Rod Piston assembly Rod cover ead cap loating bushing loating bushing Stopper Stopper bolt Orifice bsorber shaft djusting bumper Piston seal Rod seal O-ring luminum alloy luminum alloy luminum alloy luminum alloy igh carbon chrome bearing steel igh carbon chrome bearing steel Stainless steel luminum alloy Resin Stainless steel Stainless steel Stainless steel Carbon steel rass luminum alloy Polyurethane NR NR NR ard anodized ard anodized ard anodized ard anodized eat treated eat treated ith magnet eat treated eat treated, lectroless nickel plated lectroless nickel plated Chromate treated Replacement Parts: Seal Kit ore size 2 2 Kit no. MX-PS MX2-PS MX-PS MX-PS MX2-PS Contents Set of nos. Seal kit Order the seal kit, based on each bore size. Replacement Part: rease Pack pplied part uide Cylinder rease pack part no. R-S-0 ( g) R-S-0 ( g) R--00 ( g) R--0 ( g) 29 D- -X

10 MX Series MX/Stroke: 2, 0 mm Operating port 2 x M x 0. idth across hexagon socket hole 2. J. idth across flats ø9 ( ) depth 4. 9 ( ) depth 4. 4 x M4 x 0. thread depth Note) (Insert) Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. Operating port M x 0. Operating direction (Plug: MP2-0-C00-R) Operating direction Operating port M x 0. Operating direction (Plug: MP2-0-C00-R) ø ø Cross section N x M4 x 0. thread depth ottom through-hole ø. (N-) x + 9 ( ) depth 4. ø9 ( ) depth 4. MX-2 MX J 4 N 4 2 Note) Stopper bolt shown in the section above is attached only on type (with shock absorber). 290

11 ir Slide Table MX Series MX/Stroke:, 0, 2, 0 mm idth across hexagon socket hole 2. idth across flats ø9 ( ) depth 4. 9 ( ) depth 4. Operating port 2 x M x 0. J x M4 x 0. thread depth Note) (Insert). Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions MX MXS MXQ MXQ MX MX MXJ MXP MX MTS K N x M4 x 0. thread depth ottom through-hole ø. (N-) x 9 ( ) 0 depth 4. NN x M4 x 0. thread depth ottom through-hole ø. ø9 ( ) depth 4. MX- MX-0 MX-2 MX J 92 K N NN D- -X

12 MX Series MX2/Stroke: 0, mm idth across hexagon socket hole 2. Operating port 2 x M x 0. J 2. idth across flats 9 ( ) depth 4. x M4 x 0. thread depth Note) (Insert) Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. Operating port M x 0. Operating direction (Plug: MP2-0-C00-R) 4 2 ø9 ( ) depth Operating direction Operating port M x 0. Operating direction (Plug: MP2-0-C00-R) ø9 ø Cross section 4 x M x 0. thread depth ottom through-hole ø4.2 x 9 ( ) 0 depth 4. ø9 ( ) depth 4. MX2-0 MX J Note) Stopper bolt shown in the section above is attached only on type (with shock absorber). 292

13 ir Slide Table MX Series MX2/Stroke: 0, 2, 0 mm 4 idth across hexagon socket hole 2. idth across flats ø9 ( ) depth 4. 9 ( ) depth Operating port 2 x M x 0. 2 J 2. Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. x M4 x 0. thread depth Note) (Insert) 2 MX MXS MXQ MXQ MX MX MXJ MXP MX MTS K 2. N x M x 0. thread depth ottom through-hole ø4.2 (N-) x 9 ( ) 0 depth 4. M x 0. thread depth ottom through-hole ø4.2 ø9 ( ) depth 4. MX2-0 MX2-2 MX J 4 4 K 0 N 0 0 D- 29 -X

14 MX Series MX/Stroke:, 0 mm Operating port 2 x M x 0. idth across hexagon socket hole 4 Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. idth across flats + 9 ( ) depth. x M x 0. thread depth 9 Note) (Insert) Operating port M x 0. Operating direction (Plug: MP2-0-C00-R) Operating direction 9 Operating direction (Plug: MP2-0-C00-R) ø. ø Operating port M x 0. ø9 ( ) depth. 2. Cross section 4 x M x thread depth 2 ottom through-hole ø. x 9 ( ) depth. ø9 ( ) depth. MX- MX Note) Stopper bolt shown in the section above is attached only on type (with shock absorber). 294

15 ir Slide Table MX Series MX/Stroke: 2, 0,, 0 mm Operating port 2 x M x 0. idth across hexagon socket hole J 4 MX MXS idth across flats + 9 ( ) depth. Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. x M x 0. thread depth 9 Note) (Insert) MXQ MXQ MX MX MXJ 9 4 MXP MX ø9 ( ) depth. 4 2 MTS K 2 4 N x M x thread depth 2 ottom through-hole ø. (N-) x 9 ( ) depth. NN x M x thread depth 2 ottom through-hole ø. ø9 ( ) depth. J K N NN MX MX MX- MX D- -X 29

16 MX Series MX/Stroke: 0, 2 mm idth across hexagon socket hole 4 Operating port 2 x Rc / (NPT /, /) 44 2 idth across flats Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. + 9 ( ) depth. x M x 0. thread depth Note) (Insert) Operating port Rc / (NPT /, /) Operating direction (exagon socket head taper thread plug) ø9 ( ) depth Operating port Rc / (NPT /, /) Operating direction (exagon socket head taper thread plug) Operating direction ø. ø Cross section x M x thread depth 2 ottom through-hole ø. 4 x 9 ( ) depth. ø9 ( ) depth. MX-0 MX Note) Stopper bolt shown in the section above is attached only on type (with shock absorber). 29

17 ir Slide Table MX Series MX/Stroke: 0,, 0, 22, mm Operating port 2 x Rc / (NPT /, /) idth across hexagon socket hole 4 J MX MXS MXQ idth across flats Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. MXQ MX ø9 ( ) depth. 9 ( ) depth. x M x 0. thread depth Note) (Insert) MX MXJ MXP MX MTS K N x M x thread depth 2 ottom through-hole ø. (N-) x 9 ( ) depth. NN x M x thread depth 2 ottom through-hole ø. ø9 ( ) depth. J K N NN MX MX MX-0 MX D- MX X 29

18 MX Series MX2/Stroke: 0, 2, 0 mm Operating port 2 x Rc / (NPT /, /) J idth across hexagon socket hole 9. 2 idth across flats ø9 ( ) depth 9 9 ( ) depth 9 9 Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. x M x thread depth. Operating port Rc / (NPT /, /) Note) (Insert) Operating direction (exagon socket head taper thread plug) Operating port Rc / (NPT /, /) Operating direction Operating direction (exagon socket head taper thread plug) ø ø2 2 Cross section (N-) x N x M x.2 thread depth Through-hole ø. 9 9 ( ) 0 depth 9 ø9 ( ) depth 9 MX2-0 MX2-2 MX J 0 0 N Note) Stopper bolt shown in the section above is attached only on type (with shock absorber). 29

19 ir Slide Table MX Series MX2/Stroke:, 0, 22,, 2, 00 mm Operating port 2 x Rc / (NPT /, /) idth across hexagon socket hole J MX MXS idth across flats ø9 ( ) depth 9 9 ( ) depth 9 9 Note) If long bolts are used, they can touch the guide block and cause malfunction, etc. Refer to the Specific Product Precautions. x M x thread depth. Note) (Insert) MXQ MXQ MX MX MXJ 9. 2 MXP MX MTS K 2 N x M x.2 thread depth Through-hole ø. (N-) x 9 9 ( ) depth 9 NN x M x.2 thread depth Through-hole ø. ø9 ( ) depth 9 J K N NN MX MX MX MX2- MX D- MX X 299

20 MX Series uto Switch Mounting Reed uto Switch: D-90 (), D-9 (), D-9 () MX MX2 MX MX MX Stroke 2-Color Indicator Solid State uto Switch: D-M9 (), D-M9N (), D-M9P (), D-M9 () MX MX2 MX MX MX Stroke Solid State uto Switch: D-M9 (), D-M9N (), D-M9P () Note) djust the auto switch after confirming the operating conditions in theactual setting. uto Switch Proper Mounting Position (Detection at Stroke nd) 00

21 uto Switch Mounting MX Series Operating Range pplicable bore size uto switch model D-9 D D-M9 D-M9 D-M9 D-M9 D-M9 D-M9... Since the operating range is provided as a guideline including hysteresis, it cannot be guaranteed (assuming approximately 0% dispersion). It may vary substantially depending on an ambient environment. Caution Caution on andling uto Switches/or MX only Speed controller Interference xial piping port uto switch hen an auto switch is installed on the port side of MX, some switches could interfere with the speed controller or a fitting. Therefore, use one of the methods described below for installing the auto switch.. Use the port for piping in the axial direction. 2. Install an auto switch on the opposite side of the port.. Use a pipe fitting with mm width across flats or ø external diameter or less. M-J (xtension fittings) KJ04-M (One-touch fitting) Table for uto Switch Interference with Speed Controller and ittings Solid state auto switch D-M9 2-color indicator solid state auto switch D-M9 ater resistant 2-color indicator solid state auto switch D-M9 + + S-M-04 (Speed controller with One-touch fittings, lbow type) S0-04 (Speed controller with One-touch fittings, In-line type) uto switch model lectrical entry direction iring type uto switch model uto Switch Mounting Caution Interference uto Switch Mounting Tool hen adjusting the auto switch mounting screw (included with auto switch), use a watchmaker s screwdriver with a handle about to mm in diameter. Tightening torque Perpendicular Perpendicular Perpendicular -wire 2-wire -wire 2-wire -wire 2-wire D-M9N, D-M9P D-M9 D-M9N, D-M9P D-M9 D-M9N, D-M9P D-M9 MX MXS MXQ MXQ MX MX MXJ MXP MX MTS Tightening Torque of uto Switch Mounting Screw (N m) uto switch model Tightening torque D-9 () 0. to 0. D-M9 () D-M9 () 0.0 to 0. D-M9 () uto switch mounting screw (included with auto switch) uto switch atchmaker s screwdriver Other than the models listed in ow to Order, the following auto switches are applicable. Normally closed (NC = b contact) solid state auto switches (D-9/9 types) and solid state auto switch D- are also available. or details, refer to pages and. 0 D- -X

22 MX Series Made to Order: Individual Specifications Please contact SMC for detailed dimensions,specifications and lead times. Made to Order PT rease Symbol -X 4 luororubber Seal Symbol -X9 MX Standard model no. X MX Standard model no. X9 PT grease is used for all parts that grease is applied. Specifications Type PT grease ore size, 2,,, 2 Dimensions other than the above is the same as the standard type. arning Precautions e aware that smoking cigarettes, etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. 2 MX rease for ood Processing Machines Specifications rease for ood Processing Machines (NS- certified)/ Type luminum Complex Soap ase rease ore size, 2,,, 2 Dimensions other than the above is the same as the standard type. Caution Do not use this cylinder in a food-related environment. <Cannot be mounted> ood zone ood may directly contact with this cylinder, and is treated as food products. <Can be mounted> Splash zone ood may directly contact with this cylinder, but is not treated as food products. Non-food zone This cylinder do not directly contact food. Standard model no. X9 PT grease Splash zone Can be mounted ood zone Cannot be mounted ood ithout uilt-in uto Switch Magnet Symbol -X9 rease for food processing machines rease for food processing machines is used for all parts that grease is applied. MX Standard model no. ithout built-in auto switch magnet uto switch magnet is not built in. X Container Non-food zone Can be mounted. Symbol -X Specifications Type ithout built-in auto switch magnet ore size, 2,,, 2 uto switch Not mountable Dimensions other than the above is the same as the standard type. 02 Change the materials for the piston seal, rod seal, O-rings and scrapers (rubber lined parts) to fluororubber. nti-corrosive Specifications for uide Unit PDM Seal luororubber seal Specifications Type luororubber seal ore size, 2,,, 2 Seal material luororubber Dimensions other than the above is the same as the standard type. MX Standard model no. X42 Symbol -X42 nti-corrosive Specifications for uide Unit Rail and guide are given anti-corrosive treatment. Specifications Type nti-corrosive guide unit ore size, 2,,, 2 Surface treatment Special anti-corrosive treatment (2) Dimensions other than the above is the same as the standard type. 2 Special anti-corrosive treatment makes the rail and the guide black. MX Standard model no. X4 PDM seal Symbol -X4 Change the materials for the piston seal, rod seal, O-rings and scrapers (rubber lined parts) to PDM. Specifications Type PDM seal ore size, 2,,, 2 Seal material PDM rease PT grease Dimensions other than the above is the same as the standard type. arning Precautions e aware that smoking cigarettes, etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans.

23 MX Series Made to Order: Individual Specifications 2 Please contact SMC for detailed dimensions,specifications and lead times. Made to Order MX djusting olt, ong Specification (djustment range: mm) Standard model no. The average adjusting stroke range was extended from mm to mm with a long adjusting bolt. Dimensions X djusting bolt, long specification (djustment range: mm) Symbol -X MX MXS MXQ MXQ MX Standard product MX or forward-facing end or backward-facing end MXJ MXP MX MTS -X Max. Max. MX MX2 MX MX MX2 Storoke 2, 0 to 0 0, 0 to 0, 0 2 to 0 0, 2 0 to 0 to 0 to D- -X

24 MX Series Specific Product Precautions e sure to read this before handling the products. Refer to back page 0 for Safety Instructions and pages to 2 for ctuator and uto Switch Precautions. Caution Mounting of ody The slide table can be mounted from 2 directions. Select the best direction according to application requirement.. ody tapped Mounting. Do not apply scratches and dents on mounting side of body and table (guide table). The damage will decrease parallelism, increase vibration of guide and increase moving part resistance. 2. Do not scratch or dent on the forward side of the rail. This could result in looseness and increased operating resistance, etc.. Keep away from objects which are influenced by magnets. s the piston part has magnets built-in, do not allow close contact with a magnetic disk, magnetic card, or magnetic tape. Data might be erased. 4. hen mounting the body, use screws with appropriate length and do not exceed the maximum tightening torque. Tightening with a torque above the limit could malfunction. hereas tightening insufficiently could result in misalignment or come to a drop. Mounting of orkpiece Caution ød uide block. To prevent the workpiece holding bolts from touching the guide block, use bolts that are 0. mm or more shorter than the maximum screw-in depth. If the bolts are too long, they come in contact with the guide block, which could lead to a malfunction. MX MX2 MX MX MX2 2. Through-hole olt M4 x 0. M x 0. M x M x M x.2 ød ød Max. tightening Max. screw-in Positioning hole torque (N m) depth ød x ø depth 4. ø depth 4. ø depth. ø depth. ø depth 9 MX MX2 MX MX MX2 olt M4 x 0. M4 x 0. M x 0. M x 0. M x Max. tightening Max. screw-in Positioning hole torque (N m) depth ød x ø depth 4. ø depth 4. ø depth. ø depth. ø depth mm or less of flatness is recommended for the body mounting surface. Insufficient flatness of workpiece or base to which ir Slide Table is mounted can generate play in guide section or increase of sliding resistance.. The positioning hole on the table and on the bottom of the body does not have the same center. Use these holes during reinstallation after the table has been removed for the maintenance of an identical product. MX MX2 MX MX MX2 olt M x 0. M4 x 0. M x 0. M x 0. M x Max. tightening Positioning hole Depth torque (N m) ød x ø depth 4. ø depth 4. ø depth. ø depth. ø depth 9 04