2 way basic mounting: Through-hole or both ends tapped

Transcription

1 Compact Cylinder Series ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility for designing machine. Cross-section of a cylinder tube is the same configuration regardless of w/ switch or w/o switch. uto switch mounting allows for flexible designing requirements 3 faces on ø, ø, and all faces including port side on ø, ø. way basic mounting: Through-hole or both ends tapped asic mounting is way. You can choose either through-hole or both ends tapped mounting. ttachable on sides (ø, ø) Non-rotating accuracy Non-rotating rod Hexagonal cross sectional shape piston rod for high non-rotation accuracy. ø, ø ± ø, ø ±. ttachable on 3 sides (ø, ø) uto switch Standard Double acting Single rod Double rod W Standard stroke ong stroke ø ø ø ø ø ø ø ø ø ø ø ø Stroke,,,,,,,,, 3,,, 3,,,,,,,,,,,,,,,,,,,,,,,,,,,,, 3,,, Page 3 J JCQ CQ Non-rotating Rod Single acting Double acting Return/Extend Single rod K Double rod KW,, ø ø ø ø ø ø ø ø,,,,,,,,,, 3,,, 3 RQ CQM CQU MU nti-lateral oad Smooth cylinder (ow friction) Y Double acting Single rod S Refer to est Pneumatics No. -3. ø ø ø ø,,,,,,,,, 3,,, ow-speed cylinder X Refer to est Pneumatics No. -3. D- -X Technical Data

2 Series Compact Cylinder dded compact type foot brackets. Reduction of installation space Compact foot bracket has the same width as the cylinder. Overall width reduced by up to 3% (for ø) Overall width shortened Compact foot bracket More compact installation space possible Short pitch mounting is possible. llows installation close against a wall. Installed state Shortened installation width Current model Compact foot type width 3 Current foot type width Short pitch mounting is possible only without auto switch. Consult with for mounting with auto switch. Reduced width for short pitch mounting unit units 3 units 3 3 Height from the bottom of brackets to the center of a cylinder is the same as the current model. Compact foot bracket Current foot bracket H=H H H pplicable cylinders: C(D)QS, C(D)QSW, C(D)QS (Single acting, return/extend), C(D)QSK, C(D)QSKW (Non-rotating), C(D)QS S (nti-lateral load)

3 Series Compact Cylinder Reduction in labor for design dded pivot brackets for double clevis. Rotating angle: Max. (For ø, ø) Time to design rotating bracket saved. Improved amount of mounting freedom Can be mounted to an installed double clevis cylinder. Double clevis pivot bracket Rotating angle Hexagon socket head cap screw for mounting pivot bracket pplicable cylinders: ( ø to ø, Mounting bracket, pplicable only to double clevis.) J JCQ CQ RQ CQM CQU MU D- -X Technical Data

4 Combinations of Standard Products and Made Series : Standard : Made to Order specifications : Special product (Contact for details.) : Not available Symbol Standard Standard Specification Series ction/ Type pplicable bore size (Standard) Double acting Single rod/ Single rod Double rod Extension ø to ø Single acting Single rod/ Retraction D - M - C - F F G D -, M X X X X X3 XC XC XC XC XC XC3 XC XC X3 X X X X33 uilt-in magnet With rubber bumper With boss on head end Foot, Flange Double clevis type Clean series Copper (Cu) and zinc (Zn)-free () Copper () and Fluorine-free Cylinder with Stable ubrication Function (ube-retainer) () Heat-resistant cylinder ( to C) Cold-resistant cylinder ( to C) ow-speed cylinder ( to mm/s) Intermediate stroke (Using exclusive body) ow-speed cylinder ( to mm/s) Piston rod, retaining ring, rod end nut made of stainless steel djustable stroke cylinder/djustable extension type djustable stroke cylinder/djustable retraction type Dual stroke cylinder/double rod type Dual stroke cylinder/single rod type With boss on rod side Grease for food processing equipment Dust resistant cylinder Change of piston rod end of double rod cylinder Fluororubber seal ong stroke of adjustable extension stroke cylinder (-XC) ong stroke of adjustable retraction stroke cylinder (-XC) Intermediate stroke of double rod type ø to ø ø to ø ø to ø X3 X ong stroke of dual stroke single rod With concave shape end boss on the cylinder tube head side Note ) rubber bumper comes as standard. Note ) For ø and ø only. ( ) for ø and ø. Note 3) Refer to est Pneumatics No. -3 for low-speed cylinders. ø, ø Note ) Copper-free for the externally exposed part. For details, refer to the Web Catalog. Note ) For details, refer to the website. Note ) Only the products with an auto switch and without rubber bumper are compatible.

5 to Order Specifications Series K (Non-rotating rod) Double acting (ong stroke) Double acting S (nti-lateral load) Double acting Y Smooth cylinder (ow friction) (3) Double acting X ow-speed cylinder (3) Double acting Single rod Double rod Single rod Single rod Single rod Single rod ø to ø () () () () () () () J JCQ CQ RQ CQM CQU MU D- -X Technical Data

6 Series Specific Product Precautions e sure to read this before handling the products.refer to back page for Safety Instructions and pages 3 to for ctuator and uto Switch Precautions. Operating Precautions Caution. ll loads to piston rod must be applied in axial direction only. When a lateral load is applied unavoidably, ensure that it should not exceed the allowable lateral load to the rod end as specified in graph () to (). When installing a cylinder, centering should be required accurately. doption of guide mechanism is strongly recommended for the case when is used as stopper to prevent non-rotating piston rod from side loads.. When a workpiece is secured to the end of the piston rod, ensure that the piston rod is retracted entirely, and place a wrench on the portion of the rod that protrudes beyond the section. lso, tighten by giving consideration to prevent the tightening torque from being applied to the non-rotating guide. llowable ateral oad at Rod End Graph () Standard: Non-rotating Rod Type/Without uto Switch llowable lateral load W (N) Stroke ST Graph (3) nti-lateral oad Type/Without uto Switch (Mounting orientation: Horizontal) Graph () Standard: Non-rotating Rod Type/With uto Switch llowable lateral load W (N) Stroke ST Graph () nti-lateral oad Type/With uto Switch Retaining Ring Installation/Removal Caution. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring).. Even if a proper plier (tool for installing type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. llowable lateral load W (N) llowable lateral load W (N) 3 ø ø ø ø Stroke ST Graph () ong Stroke/With & Without uto Switch llowable lateral load W (N) Stroke ST Note ) Graph () to (): Rod end female thread Note ) ateral load allowance varies depending upon rod end shape dimensions or load value (distance to the center of the gravity of load). Please consult with. Stroke ST

7 With auto switch C F G D With auto switch (uilt-in magnet) Mounting type Through-hole/oth ends tapped common (Standard) Foot type Compact foot type Rod side flange type Head side flange type Double clevis type D CDQS D mm mm mm mm In the case of long strokes, use either ends tapped mounting or bracket mounting. Mounting brackets are shipped together (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to Mounting olt for on pages and. Cylinder stroke Standard stroke ong stroke MW ody option <Standard stroke> Number of auto switches Nil S n pcs. pc. n pcs. uto switch Nil Without auto switch Refer to the table below for the applicable auto switch model. Made to Order Refer to page for details. <ong stroke> Nil Standard With rubber bumper C C With rubber bumper Rod end female thread (Standard) M With rubber bumper CM F oss on head end,,, 3,,,,,,, Combination of body options is Rubber bumper is standard equipment for,,,,, available. CM, FC, FM, FCM long stroke type.,,,,,,,,,, ction uilt-in Magnet Cylinder Model, 3,,,,,,, D Double acting If a built-in magnet cylinder without an auto J,,, switch is required, there is no need to enter For Manufacture of Intermediate Strokes, refer to page. the symbol for the auto switch. (Example) CDQS-D pplicable uto Switches/Refer to pages to for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Compact Cylinder: Standard Type Double cting, Single Rod Series ø, ø, ø, ø Electrical entry Wiring (Output) oad voltage 3-wire (NPN) 3-wire (PNP) -wire V, V V 3-wire (NPN) Diagnostic indication V, V (-color indicator) 3-wire (PNP) Grommet Yes V -wire V 3-wire (NPN) Water resistant (-color indicator) 3-wire (PNP) -wire V, V V Magnetic field resistant (-color indicator) -wire (Non-polar) 3-wire Grommet Yes (NPN equivalent) V No -wire V V Indicator light How to Order DC C V V or less uto switch model Perpendicular MNV MN MPV MP MV M MNWV MNW MPWV MPW MWV MW MNV MN MPV MP MV M P3DW V 3V V In-line 3 Water resistant type auto switches can be mounted on the above models, but in such case cannot guarantee water resistance. Consult with regarding water resistant types with the above model numbers. m type lead wire is only applicable to D-3. ead wire length (m). (Nil) (M) 3 () (Z) Pre-wired connector pplicable load ead wire length symbols:. m Nil (Example) MNW Solid state auto switches marked with are produced upon receipt of order. m M (Example) MNWM vailable only for ø. 3 m (Example) MNW It is mounted away from the port side to avoid interference with fittings. m Z (Example) MNWZ Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages and. uto switches are shipped together (not assembled). Note) There is the case D- V/M V/M WV/M V type auto switches cannot be mounted on the port surface, depending on the cylinder s stroke and the fitting size for piping. Consult with for details. IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC 3 JCQ CQ RQ CQM CQU MU D- -X Technical Data

8 Series Symbol Without cushion Rubber bumper Specifications ction Fluid ubrication Proof pressure Maximum operating pressure Double acting, Single rod ir Not required (Non-lube). MPa. MPa Minimum operating pressure. MPa. MPa Without auto switch: to C (No freezing) mbient and fluid temperature With auto switch: to C (No freezing) Cushion Rod end thread None, Rubber bumper Female thread Stroke length tolerance Standard stroke: +. ong stroke: +. Piston speed to mm/s llowable kinetic energy (J) Standard type..3.. With rubber bumper.3... Stroke length tolerance does not include the deflection of the bumper. Only rubber bumper is available for the long stroke type. Made to Order: Individual Specifications (For details, refer to pages to ) Symbol Specifications -X Fluororubber seals -X ong stroke of adjustable extension stroke cylinder (-XC) -X ong stroke of adjustable retraction stroke cylinder (-XC) -X3 ong stroke of dual stroke single rod -X With concave shape end boss on the cylinder tube head side Made to Order Specifications (For details, refer to pages 3 to.) Symbol Specifications -X Change of rod end shape -X Heat-resistant cylinder ( to C) (without an auto switch) -X Cold-resistant cylinder ( to C) (without an auto switch) -X ow speed cylinder ( to mm/s) -X Intermediate stroke (Using exclusive body) -X3 ow speed cylinder ( to mm/s) -XC Piston rod, retaining ring, rod end nut made of stainless steel -XC djustable stroke cylinder/djustable extension type -XC djustable stroke cylinder/djustable retraction type -XC Dual stroke cylinder/double rod type -XC Dual stroke cylinder/single rod type -XC3 With boss in rod side -XC Grease for food processing equipment -XC Dust resistant cylinder ody Option Description pplication vailable for all standard models of double acting, Rubber bumper single rod. Rubber bumper is standard equipment for long stroke type. Moisture Control Tube IDK Series When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. For details, refer to the IDK series in the est Pneumatics No.. Theoretical Output Rod size Operating direction IN OUT IN OUT IN OUT IN OUT Manufacture of Intermediate Stroke Standard stroke Description Part no. Description Description,, Piston area (mm ) Spacer is installed in the standard stroke body. Refer to How to Order for the standard model no. (page 3). to to OUT IN (N) Operating pressure (MPa) Exclusive body (-X) Suffix -X to the end of standard model no. (page 3). Intermediate strokes in mm Dealing with the stroke in mm increments are available by using increments by using an exclusive spacers with standard stroke cylinders. body with the specified stroke.,, to to Intermediate strokes in mm Dealing with the stroke in mm increments are available by using increments by using an exclusive spacers with standard stroke cylinders. body with the specified stroke. ong stroke, 3 to to to, 3 to to to Part no.: -D Part no.: -D-X Example -D with 3 mm width Makes stroke tube. spacer inside. dimension is. mm. dimension is. mm. Refer to pages to for cylinders with auto switches. Minimum auto switch mounting stroke Proper auto switch mounting position (detection at stroke end) and mounting height Operating range uto switch mounting bracket/part no.

9 Compact Cylinder: Standard Type Double cting, Single Rod Series Weight/Without uto Switch (g) Cylinder stroke For standard stroke Calculation: (Example) D-DCM Cylinder weight: -D g dditional weight: g dditional weight: Rubber bumper g dditional weight: Double clevis type g g Weight/With uto Switch (uilt-in magnet) (g) Cylinder stroke dditional Weight (g) Male thread. Nut With boss on head end Rubber bumper (No need to add for long stroke) 3 Compact foot type (Including mounting bolt) (3) () () (3) Foot type (Including mounting bolt) (3) () (3) () Rod side flange type (Including mounting bolt) () () 3 (3) () Head side flange type (Including mounting bolt) 3 Double clevis type (Including pin, snap ring, bolt) ( ): denotes the values of long stroke model. 3 Mounting racket Part No. Foot Compact foot () Flange Double clevis C -C -C -C -F -F -F -F -D -D -D -D Note) When ordering foot and compact foot brackets, order pieces per cylinder. Note) Parts belonging to each bracket are as follows. Foot, Compact foot, Flange type: ody mounting bolt Double clevis type: Clevis pin, Type C retaining ring for axis, ody mounting bolt. J JCQ CQ RQ CQM CQU MU D- -X Technical Data

10 Series llowable Kinetic Energy oad Mass and Piston Speed Standard/. llowable kinetic energy: Ea With rubber bumper/.3 llowable kinetic energy: Eb (m+m)v Kinetic energy E (J) =.3. m: Mass of cylinder movable parts kg m: oad mass kg V: Piston speed m/s.. [J].. Mass of Movable Parts/Without uilt-in Magnet: - D(C)(M) (g) Cylinder stroke Mass of Movable Parts/With uilt-in Magnet: CDQS - D(C)(M) (g) Cylinder stroke dditional Mass of Movable Parts Male thread Nut Rubber bumper (No need to add for long stroke) Foot type, Rod side flange type (No need to add for long stroke) Calculation: (Example) -DCM asic mass: -D g dditional mass: g : With rubber bumper g Total 3 g 3 (g) 3

11 Compact Cylinder: Standard Type Double cting, Single Rod Series Clean Series (Standard stroke is only available.) C(D)QS Stroke D(M) Clean Series Specifications ction Proof pressure Maximum operating pressure Rubber bumper Piping Piston speed Mounting uto switch Note) For details, please contact. Smooth Cylinder Y X Relief type Vacuum type Mounting Smooth Cylinder Double acting, Single rod ø, ø, ø, ø. MPa. MPa None Screw-in piping to mm/s Through-hole/oth ends tapped common Mountable Smooth operation with a little sticking and slipping at low speed. Dual-side low friction operation is possible. Some of the parts are different from the dimensions of the double acting, single rod type. Refer to est Pneumatics No. -3. ow-speed Cylinder Mounting ow-speed Cylinder The type which is applicable for using inside the clean room graded ISO Class by making an actuator s rod section a double seal construction and discharging by relief port directly to the outside of clean room. Stroke DC(M) Stroke D(C)(M) Smooth operation with a little sticking and slipping at low speed. Can start smoothly with a little ejection even after being rendered for hours. The dimensions are the same as the double acting, single rod type. Refer to est Pneumatics No. -3. Relief port For details, refer to the Pneumatic Clean Series (CT.E-3) Specifications Type Pneumatic (Non-lube) ction Double acting, Single rod Fluid ir Proof pressure. MPa Maximum operating pressure. MPa mbient and fluid Without auto switch: to C (No freezing) temperature With auto switch: to C (No freezing) Cushion None, Rubber bumper Rod end thread Female thread Stroke length tolerance +. Mounting Through-hole/oth ends tapped common Piston speed to mm/s llowable leakage. /min (NR) or less Stroke length tolerance does not include the deflection of the bumper. Minimum operating pressure Minimum operating pressure (MPa).3. Specifications Type Pneumatic (Non-lube) ction Double acting, Single rod Fluid ir Proof pressure. MPa Maximum operating pressure. MPa mbient and fluid Without auto switch: to C temperature (No freezing) With auto switch: to C Rubber bumper None, Rubber bumper Rod end thread Female thread Stroke length tolerance Standard stroke +. Mounting Through-hole/oth ends tapped common Piston speed ø, ø: to mm/s ø, ø:. to mm/s Stroke length tolerance does not include the deflection of the bumper. Minimum operating pressure Minimum operating pressure.3.3. (MPa). J JCQ CQ RQ CQM CQU MU D- -X Technical Data

12 Series Compact Cylinder with Stable ubrication Function (ube-retainer) With auto switch (uilt-in magnet) M C D QS Mounting type Stroke D Rod end thread uto switch With stable lubrication function (ube-retainer) * vailable only for with auto switch. Specifications, ction Double acting, Single rod Minimum operating pressure Piston speed Cushion. MPa to mm/s None * Specifications other than those shown above are the same as the standard model. Dimensions (Dimensions other than those shown below are the same as the standard model.) DM: øt øt Standard stroke T,,,,,, 3,,, * The mounting dimensions of the mounting bracket are the same as the standard model. (Flat washer pcs.) Mounting racket Part No. Foot Compact foot Flange -M -CM -FM -M -CM -FM * The double clevis type is the same as the standard model. * When ordering foot and compact foot brackets, order pieces per cylinder. For details, refer to the Web Catalog.

13 Compact Cylinder: Standard Type Double cting, Single Rod Series Construction asic type With rubber bumper With auto switch (uilt-in magnet) ø, ø w t!! q r! e i o t! w! r q u!! e ong stroke ø, ø!!!3! y w t!! r q!! e With boss on head end! J Component Parts No. Description Cylinder tube Collar 3 Piston Piston rod Retaining ring Rod end nut Spacer for switch type umper umper ottom plate Material luminum alloy luminum alloy luminum alloy Stainless steel Carbon tool steel Carbon steel luminum alloy Urethane Urethane luminum alloy Note Hard anodized nodized Phosphate coated Nickel plated Chromated nodized Component Parts No. 3 Description Collar ushing Wear ring Magnet Centering location ring Rod seal Piston seal Tube gasket Materia luminum alloy Oil-impregnated sintered alloy Resin luminum alloy NR NR NR Note nodized nodized Replacement Parts: Seal Kit (asic type) Kit no. -PS -PS -PS -PS Contents Set of nos. above!,!,! Replacement Parts: Seal Kit (ong stroke) Kit no. --PS --PS --PS --PS Contents Set of nos. above!,!,! Seal kit includes!,!,!. Order the seal kit, based on each bore size. (The long stroke type includes tube gaskets.) Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) JCQ CQ RQ CQM CQU MU D- -X Technical Data

14 Series Mounting olt for without uto Switch Mounting method: Mounting bolt for through-hole mounting type of is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x pcs. O thread Mounting bolt Note ) The appropriate plain washer must be used for through-hole mounting. Note ) Please contact for details concerning the mounting bolts to be used with ø and ø that exceed mm strokes, or ø and ø that exceed mm strokes. Cylinder model C D Mounting bolt part no. D D CQ-M3 x M3 x D 3 M3 x 3. D M3 x D D 3DC DC DC M3 x M3 x M3 DC Secure the cylinder by using the O screws that DC are provided with the DC cylinder tube. DC DC DC DC D D CQ-M3 x M3 x D 3 M3 x 3. D M3 x D D 3DC DC DC M3 x M3 x DC Secure the cylinder by using the O screws that DC are provided with the DC cylinder tube. DC DC DC DC Cylinder model C D Mounting bolt part no. D D D D 3 CQ-M x M3 x M3 x 3 M3 x D M3 x. D M3 x 3D D D D DC M3 x M3 x M3 x M3 x DC DC Secure the cylinder by using the O screws that are provided with the DC cylinder tube. DC DC D D D D 3 CQ-M x M x 3 M3 x M x D M3 x. D M x 3D D D D DC DC M3 x M x M3 x M x DC Secure the cylinder by using the O screws that DC are provided with the DC cylinder tube. DC DC DC Material: Chromium molybdenum steel Surface treatment: Nickel plated

15 Compact Cylinder: Standard Type Double cting, Single Rod Series Mounting olt for CDQS with uto Switch Mounting method: Mounting bolt for through-hole mounting type of CDQS is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x pcs. O thread Mounting bolt Note ) The appropriate plain washer must be used for through-hole mounting. Note ) Please contact for details concerning the mounting bolts to be used with ø and ø that exceed mm strokes, or ø and ø that exceed mm strokes. ccessory For accessory bracket for the series, refer to page, since it is commonly used with the CQ series. Single knuckle joint Pin for knuckle Double knuckle joint Rod end nut Cylinder model C D Mounting bolt part no. Cylinder model C D Mounting bolt part no. CDQSD CDQSD 3 CQ-M3 x M3 x 3 CDQSD CDQSD 3 CQ-M x 3 M3 x CDQSD M x CDQSD M x. CDQSD M3 x CDQSD M3 x CDQSD M x CDQSD M x. CDQSD M3 x CDQSD M3 x CDQS3DC CDQSDC CDQSDC CDQSDC Secure the cylinder by CDQS3D CDQSD CDQSD CDQSD M x M3 x M x M3 x CDQSDC using the O screws that CDQSDC are provided with the CDQSDC CDQSDC Secure the cylinder by cylinder tube. CDQSDC CDQSDC using the O screws that are provided with the CDQSDC CDQSDC cylinder tube. CDQSDC CDQSDC CDQSDC CDQSD CDQSD 3 CQ-M3 x M3 x 3 CDQSDC CDQSD CDQSD CQ-M x x CDQSD M x CDQSD x. CDQSD M3 x CDQSD x CDQSD M x CDQSD x. CDQSD M3 x CDQSD x CDQS3DC CDQSDC CDQSDC CDQSDC Secure the cylinder by CDQS3D CDQSD CDQSD CDQSD x x x x CDQSDC using the O screws that CDQSDC are provided with the CDQSDC CDQSDC cylinder tube. CDQSDC CDQSDC Secure the cylinder by using the O screws that CDQSDC CDQSDC are provided with the CDQSDC CDQSDC cylinder tube. CDQSDC CDQSDC CDQSDC CDQSDC Material: Chromium molybdenum steel Surface treatment: Zinc chromated J JCQ CQ RQ CQM CQU MU D- -X Technical Data

16 Series Dimensions: ø to ø asic type (Through-hole/oth ends tapped common): /CDQS ø For the auto switch mounting position and its mounting height, refer to page. ø H thread effective depth C x M x. x x øo counterbore R x x O counterbore R Note) uto switch Minimum lead wire bending radius x øn through Flat washer pcs. ø, ø + Stroke + Stroke Width across flats MM With boss on head end H øth C X G ength with intermediate stroke () Spacer... The dimensions will be identical to those of the nearest long stroke. Those that exceed the standard stroke will have the long stroke dimensions. () Exclusive body (-X) dd stroke. lso, the stroke length that exceeds the standard stroke would be the long stroke dimension. asic Type Standard stroke range to to to to Standard stroke Without auto switch.. F With auto switch F ong stroke range 3 to 3 to to to ong stroke With/Without auto switch F C With oss on Head End MM X G Th D E 3 H M3 x. M x. M x. M x... 3 Note) The product with boss on head end is applicable to only the standard stroke. Note) With boss on rod end : Option (Suffix -XC3 to the end of part number.) Note that only bore sizes ø and ø are applicable to the long stroke. I 3 3 K M.. N O M x. M x. M x. M x. O.. Q R R T Note ) For the following bore/stroke sizes through-hole is threaded over the entire length: asic type ø and ø; stroke, ø; to stroke, ø; to stroke, ø with auto switch built-in magnet; stroke. Note ) Rubber bumper type has the same dimensions as those indicated above. For details about the rod end nut and accessory brackets, refer to page. Rod End Male Thread C H 3 Standard stroke... ong stroke.. 3. M x.. M x. M x. M x

17 Compact Cylinder: Standard Type Double cting, Single Rod Series Foot type: /CDQS X Z H Y x ød X Y + Stroke T + Stroke Y X Compact foot type: C/CDQSC X Z Rod side flange type: F/CDQSF Head side flange type: G/CDQSG + Stroke + Stroke H Y x ød Rod end nut Rod end nut T Y x øfd X + Stroke S + Stroke + Stroke + Stroke + Stroke X Special cap bolt G S + Stroke Special cap bolt Y x øfd Foot Type FD.... Standard stroke range to to to to Standard stroke range to to to to FD.... FT FT FV 3.. FV 3.. FX S.. FX FZ. 3. FZ S to 3 to to to D G H T X Y Z Compact Foot Type Standard stroke range to to to to Rod Side Flange Type Standard stroke ong ong stroke Without auto switch With auto switch stroke range Without/With auto switch Standard stroke Without auto switch With auto switch S S ong stroke range 3 to 3 to to to S 3 3 Head Side Flange Type Standard Standard stroke ong ong stroke stroke stroke range Without auto switch With auto switch range Without/With auto switch to to 3 3. to to to to 3... to to Flange bracket material: Carbon steel Surface treatment: Nickel plated Flange bracket material: Carbon steel Surface treatment: Nickel plated X.. Y... Foot bracket material: Carbon steel Surface treatment: Nickel plated.... D H T X Y Z ong stroke range 3 to 3 to to to ong stroke Without/With auto switch S Standard stroke ong stroke Without auto switch With auto switch Without/With auto switch X Y... Compact foot bracket material: Carbon steel Surface treatment: Zinc chromated For details about the rod end nut and accessory brackets, refer to page. 3 J JCQ CQ RQ CQM CQU MU D- -X Technical Data

18 Series Dimensions: ø to ø Double clevis type: D/CDQSD Cap bolt øcd hole H Rod d + Stroke C+Stroke + Stroke Rod end nut Double Cevis Type Standard stroke range to to to to C C CD Standard stroke ong ong stroke stroke Without auto switch With auto switch range Without/With auto switch C C to to to to 3. CT CW CX. CZ RR Double clevis bracket material: Carbon steel Surface treatment: Nickel plated For details about the double clevis pivot bracket, refer to page. For details about the rod end nut and accessory brackets, refer to page.

19 Series ccessory Dimensions Double Clevis Pivot racket ø to ø øcd hole H. CX. C x øcn R + Stroke CW CT M CZ racket ore Stroke Hexagon socket head cap screw for part no. size range CW CT C CX CD M CZ R CN Without auto switch With auto switch mounting pivot bracket (ccessory) CQ-C to M x CQ-C to M x CQ-C to. 3. M x CQ-C to... M x The double clevis pin and retaining ring are not included. Double clevis pivot bracket material: Carbon steel Surface treatment: Nickel plated J JCQ CQ RQ CQM CQU MU D- -X Technical Data

20 With auto switch W D C CDQSW D C With auto switch (uilt-in magnet) Mounting type Through-hole/oth ends tapped common (Standard) Foot type C Compact foot type F Flange type Mounting brackets are shipped together (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to Mounting olt for W on page. mm mm mm mm Cylinder stroke Standard Stroke Standard stroke,,,,,,,,,,,,, 3,,, For Manufacture of Intermediate Strokes, refer to page. MW ody option Nil C M Standard With rubber bumper Combination of body options is available. CM ction D Double acting pplicable uto Switches/Refer to pages to for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Compact Cylinder: Standard Type Double cting, Double Rod W Series ø, ø, ø, ø Electrical entry oad voltage Wiring (Output) DC C 3-wire (NPN) 3-wire (PNP) -wire V, V V 3-wire (NPN) Diagnostic indication V, V (-color indicator) 3-wire (PNP) Grommet Yes V -wire V 3-wire (NPN) Water resistant (-color indicator) 3-wire (PNP) -wire V, V V Magnetic field resistant (-color indicator) -wire (Non-polar) 3-wire Grommet Yes (NPN equivalent) V No -wire V V Indicator light How to Order V V or less uto switch model Perpendicular MNV MN MPV MP MV M MNWV MNW MPWV MPW MWV MW MNV MN MPV MP MV M P3DW V 3V V In-line 3 Water resistant type auto switches can be mounted on the above models, but in such case cannot guarantee water resistance. Consult with regarding water resistant types with the above model numbers. m type lead wire is only applicable to D-3. Made to Order Refer to page for details. Number of auto switches Nil S n pcs. pc. n pcs. uto switch Nil Without auto switch Refer to the table below for the applicable auto switch model. uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDQSW-D ead wire length (m). (Nil) (M) 3 () (Z) Pre-wired connector pplicable load ead wire length symbols:. m Nil (Example) MNW Solid state auto switches marked with are produced upon receipt of order. m M (Example) MNWM vailable only for ø. 3 m (Example) MNW It is mounted away from the port side to avoid interference with fittings. m Z (Example) MNWZ Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages and. uto switches are shipped together (not assembled). Note) There is the case D- V/M V/M WV/M V type auto switches cannot be mounted on the port surface, depending on the cylinder s stroke and the fitting size for piping. Consult with for details. IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC

21 Compact Cylinder: Standard Type Double cting, Double Rod W Series Symbol WIthout cushion Symbol -X3 -X -X33 Symbol -X -X -X -X -X -X3 -XC -XC3 -XC Moisture Control Tube IDK Series Rubber bumper Made to Order: Individual Specifications (For details, refer to pages and.) Specifications Change of piston rod end of double rod cylinder Fluororubber seals Intermediate stroke of double rod cylinder Made to Order Specifications (For details, refer to pages 3 to.) Specifications Change of rod end shape Heat-resistant cylinder ( to C) (without an auto switch) Cold-resistant cylinder ( to C) (without an auto switch) ow speed cylinder ( to mm/s) Intermediate stroke (Using exclusive body) ow speed cylinder ( to mm/s) Piston rod, retaining ring, rod end nut made of stainless steel With boss in rod side Grease for food processing equipment ody Option Description Rubber bumper pplication vailable for all standard models of double acting, double rod. Mounting racket Part No. Foot () Compact foot () -C -C -C -C Flange -F -F -F -F Note ) When ordering foot and compact foot brackets, order pieces per cylinder. Note ) Parts belonging to each bracket are as follows. Foot, Compact foot, Flange type: ody mounting bolt When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. For details, refer to the IDK series in the est Pneumatics No.. Specifications ction Fluid ubrication Double acting, Double rod ir Not required (Non-lube) Proof pressure Maximum operating pressure. MPa. MPa Minimum operating pressure. MPa. MPa Without auto switch: to C (No freezing) mbient and fluid temperature Cushion Rod end thread With auto switch: to C (No freezing) None, Rubber bumper Female thread Stroke length tolerance +. mm Piston speed to mm/s Standard type..3.. llowable kinetic energy (J) With rubber bumper.3... Stroke length tolerance does not include the deflection of the bumper. Theoretical Output IN OUT IN OUT IN OUT IN OUT Manufacture of Intermediate Stroke Description Rod size Operating direction Spacer is installed in the standard stroke body. Piston area (mm ). 3 3 Refer to pages to for cylinders with auto switches. (N) Operating pressure (MPa).3 3. Exclusive body (-X) Part no. Suffix -X33 to the end of standard Suffix -X to the end of standard model no. (page ). model no. (page ). Intermediate strokes in mm Dealing with the stroke in mm Description increments are available by using increments by using an exclusive body spacers with standard stroke cylinders. with the specified stroke., to, to, to, to Part no.: W-D-X33 Part no.: W-D-X Example W-D with 3 mm width Makes stroke tube. spacer inside. dimension is mm. dimension is mm. Minimum auto switch mounting stroke Proper auto switch mounting position (detection at stroke end) and mounting height Operating range uto switch mounting bracket/part no.. J JCQ CQ RQ CQM CQU MU D- -X Technical Data

22 W Series Weight/Without uto Switch 3 Cylinder stroke Weight/With uto Switch (uilt-in magnet) dditional Weight 3 Male thread Nut With rubber bumper Foot type (Including mounting bolt) Compact foot type (Including mounting bolt) Rod side flange type (Including mounting bolt) Cylinder stroke (g) 3 (g) 33 (g) Caution Retaining Ring Installation/Removal. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring).. Even if a proper plier (tool for installing type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. Warning Mounting Do not apply the reverse torque to the piston rods sticking out from both sides of this cylinder at the same time. The torque makes connection threads inside loosen, which may cause an accident or malfunction. Install or remove a load while the piston rod width across flats are secured. Do not fix the other side of piston rod width across flat and apply the reverse torque. Calculation: (Example) WF-DM Cylinder weight: W-D g dditional weight: g : Rod side flange type g g

23 Compact Cylinder: Standard Type Double cting, Double Rod W Series Construction asic type With rubber bumper With auto switch (uilt-in magnet) ø, ø ø, ø J Component Parts No. 3 3 Description Cylinder tube Collar Piston Piston rod Piston rod Retaining ring Rod end nut umper Spacer for switch Magnet Rod seal Piston seal Tube gasket Material luminum alloy luminum alloy luminum alloy Stainless steel Stainless steel Carbon tool steel Carbon steel Urethane luminum alloy NR NR NR Note Hard anodized nodized Phosphate coated Nickel plated Chromated JCQ CQ RQ CQM CQU MU Replacement Parts/Seal Kit Kit no. W-PS Contents W-PS W-PS Set of nos. above!,!,!3 W-PS Seal kit includes!,!,!3. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) D- -X Technical Data

24 W Series Mounting olt for W Mounting method: Mounting bolt for through-hole mounting type of W is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x pcs. Mounting bolt Note) When mounting a cylinder with throughhole, be sure to use the attached plain washer. Cylinder model W-D -D C D 3 Mounting bolt part no. CQ-M3 x x 3 Cylinder model W-D -D C D Mounting bolt part no. CQ-M x x -D x -3D x. -D x -D x -D -D W-D -D 3 x x CQ-M3 x x 3 -D -D W-D -D 3 x x CQ-M x 3 x -D x -D x. -D x -D x -D x -D x -D x -D x W-D 3 CQ-M x 3-3D x -D x -D x -D x -D x -D x -D x Material: Chromium molybdenum steel Surface treatment: Zinc chromated Mounting olt for CDQSW with uto Switch Mounting method: Mounting bolt for through-hole mounting type of CDQSW is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x3 pcs. Note) When mounting a cylinder with throughhole, be sure to use the attached plain washer. Mounting bolt Cylinder model CDQSW-D -D C D 3 Mounting bolt part no. CQ-M3 x 3 x Cylinder model CDQSW-D -D C D Mounting bolt part no. CQ-M x x -D x -3D x. -D x -D x -D -D CDQSW-D -D 3 x x CQ-M3 x 3 x -D -D CDQSW-D -D x x CQ-M x x -D x -D x. -D x -D x -D x -D x -D x -D x CDQSW-D CQ-M x -3D x -D x -D x -D x -D x -D x -D x Material: Chromium molybdenum steel Surface treatment: Zinc chromated

25 Compact Cylinder: Standard Type Double cting, Double Rod W Series Dimensions: ø to ø asic type (Through-hole/oth ends tapped common): W/CDQSW x x øo counterbore R H thread effective depth C x x O effective depth R Note) x M x. uto switch Minimum lead wire bending radius Width across flats K x øn through Flat washer pcs. + Stroke + Stroke + (Stroke), Width across flats MM Width across flats MM J H C X + (Stroke) H C X + Stroke JCQ CQ Rod End Male Thread Without auto switch With auto switch C H... MM M x. M x. M x. M x. X.. RQ CQM CQU MU asic Type to to to to Without auto switch With auto switch Note ) For basic type ø and ø with stroke, through-hole is threaded over the entire length. Note ) Rubber bumper type has the same dimensions as those indicated above Note 3) The positions of width across flats on both sides are not the same. For details about the rod end nut and accessory brackets, refer to page. C D E 3 H M3 x. M x. M x. M x. I 3 3 K M.. N O M x. M x. M x. M x. O.. Q.. R R T.. D- -X Technical Data

26 W Series Dimensions: ø to ø Foot type: W/CDQSW Special cap bolt + Stroke + Stroke Y H X Z x ød X Y T Y X S + Stroke + (Stroke) G + (Stroke) + Stroke Foot Type to to to to Without auto switch 3 3 S Compact foot type: WC/CDQSWC With auto switch S 3. D. G. H T X 3 Y. Z X Special cap bolt + Stroke Y... Foot bracket material: Carbon steel Surface treatment: Nickel plated + Stroke H T Y X Z x ød Y X X Y S + Stroke + (Stroke) Compact Foot Type Without auto switch With auto switch S S to to to to For details about the rod end nut and accessory brackets, refer to page (Stroke) + Stroke D H T X Y Z Compact foot bracket material: Carbon steel Surface treatment: Zinc chromated X Y...

27 Compact Cylinder: Standard Type Double cting, Double Rod W Series Dimensions: ø to ø Flange type: WF/CDQSWF x øfd + Stroke + Stroke + (Stroke) Rod end nut + (Stroke) 3 + Stroke Flange Type to to to to Without auto switch With auto switch FD.... For details about the rod end nut and accessory brackets, refer to page. Note ) The positions of width across flats on both sides are not the same. FT.. FV 3 FX FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated J JCQ CQ RQ CQM CQU MU 3 D- -X Technical Data

28 Compact Cylinder: Standard Type Single cting, Single Rod Series ø, ø, ø, ø How to Order S With auto switch CDQS S MWV With auto switch (uilt-in magnet) Made to Order Refer to page for details. C F G D Mounting type Through-hole/oth ends tapped common (Standard) Foot type Compact foot type Rod side flange type Head side flange type Double clevis type Mounting brackets are shipped together (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to Mounting olt for on page. mm mm mm mm Cylinder stroke Standard Stroke Standard stroke,,,, For Manufacture of Intermediate Strokes, refer to page. Number of auto switches Nil S n pcs. pc. n pcs. uto switch Nil Without auto switch Refer to the table below for the applicable auto switch model. ody option Nil Standard (Rod end female thread) M F oss on head end Combination of body options is available. FM ction S Single acting, Spring return T Single acting, Spring extend uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDQS-T pplicable uto Switches/Refer to pages to for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (-color indicator) Water resistant (-color indicator) Electrical entry Indicator light oad voltage Wiring (Output) DC C 3-wire (NPN) 3-wire (PNP) -wire V, V V 3-wire (NPN) Grommet Yes 3-wire (PNP) -wire 3-wire (NPN) 3-wire (PNP) -wire 3-wire Yes (NPN equivalent) Grommet V V, V V V, V V V No -wire V V V V or less uto switch model Perpendicular MNV (MN) MPV (MP) MV (M) MNWV (MNW) MPWV (MPW) MWV (MW) MNV (MN) MPV (MP) MV (M) V 3V V In-line 3 Water resistant type auto switches can be mounted on the above models, but in such case cannot guarantee water resistance. Consult with regarding water resistant types with the above model numbers. m type lead wire is only applicable to D-3. ead wire length (m). (Nil) (M) 3 () (Z) Pre-wired connector pplicable load ead wire length symbols:. m Nil (Example) MNWV Solid state auto switches marked with are produced upon receipt of order. m M (Example) MNWVM 3 m (Example) MNWV m Z (Example) MNWVZ Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages and. uto switches are shipped together (not assembled). Note ) There is the case D- V/M V/M WV/M V type auto switches cannot be mounted on the port surface, depending on the cylinder s stroke and the fitting size for piping. Consult with for details. Note ) The D-M (in-line entry) type auto switch in ( ) cannot be mounted due to the manufacturable stroke. When this auto switch satisfies the conditions stated in Note 3) on page, it can be ordered separately. IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC

29 Compact Cylinder: Standard Type Single cting, Single Rod Series Symbol Single acting, Spring return Single acting, Spring extend Standard Specifications ction Fluid ubrication Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Cushion Rod end thread Stroke length tolerance Piston speed llowable kinetic energy (J) Single acting, Single rod ir Not required (Non-lube). MPa. MPa. MPa. MPa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) None Female thread +. mm to mm/s..3.. Symbol Specifications -X Fluororubber seals -X Made to Order: Individual Specifications (For details, refer to pages and.) Made to Order Specifications (For details, refer to pages 3 to.) Symbol Specifications -X Change of rod end shape Intermediate stroke (Using exclusive body), -X Extension type only -XC Piston rod, retaining ring, rod end nut made of stainless steel -XC3 With boss on rod side, ø and ø only -XC Grease for food processing equipment ody Option Description Moisture Control Tube IDK Series pplication vailable for all standard models of single acting, single rod. Mounting racket Part No. With concave shape end boss on the cylinder tube head side Foot () Compact Flange Double clevis foot () - -C -F -D - -C -F -D - -C -F -D - -C -F -D Note ) When ordering foot and compact foot brackets, order pieces per cylinder. Note )Parts belonging to each bracket are as follows. Foot, Compact foot, Flange type: ody mounting bolt Double clevis type: Clevis pin, Type C retaining ring for axis, ody mounting bolt. When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. For details, refer to the IDK series in the est Pneumatics No.. Theoretical Output ction Spring return Spring extend IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT Manufacture of Intermediate Stroke (Single acting, Spring retract type is excluded.) Description Part no. Description Example Rod size Operating direction Piston area (mm ) Operating pressure (MPa) Refer to pages to for cylinders with auto switches. Minimum auto switch mounting stroke Proper auto switch mounting position (detection at stroke end) and mounting height Operating range 3 (N) Retracted Extended side side Spacer is installed in the standard stroke body. Refer to How to Order for the standard model no. (page ). Intermediate strokes in mm increments are available by using spacers with standard stroke cylinders. to to Part no.: -3T -T with mm width spacer inside. dimension is. mm. J JCQ CQ RQ CQM CQU MU D- -X Technical Data

30 Series Weight/Without uto Switch Spring return (Spring extend) (g) Cylinder stroke (3) 3 (3) 3 () () 3 (3) () () (3) ( ): Denotes the values of spring extend. dditional Weight Male thread Nut Foot type (Including mounting bolt) Compact foot type (Including mounting bolt) Rod side flange type (Including mounting bolt) Head side flange type (Including mounting bolt) Double clevis type (Including pin, retaining ring, bolt) Calculation: (Example) G-S Cylinder weight: -S g dditional weight: Head side flange type g g Weight/With uto Switch (uilt-in magnet) Spring return (Spring extend) (g) Cylinder stroke 3 (3) () () () () () () () ( ): Denotes the values of spring extend (g) Caution Retaining Ring Installation/Removal. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring).. Even if a proper plier (tool for installing type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. Mounting olt for without uto Switch Mounting method: Mounting bolt for through-hole mounting type of is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x pcs. Single acting, Spring return Note) When mounting a cylinder with through-hole, be sure to use the attached plain washer. Mounting olt for CDQS with uto Switch Mounting method: Mounting bolt for through-hole mounting type of CDQS is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x pcs. Single acting, Spring return Note) When mounting a cylinder with through-hole, be sure to use the attached plain washer. Mounting bolt Mounting bolt Single acting, Spring extend Single acting, Spring extend Mounting bolt Mounting bolt Single cting, Spring Return Cylinder model C D Mounting bolt part no. -S CQ-M3 x. -S x -S CQ-M3 x. -S x -S CQ-M x. -S x -S CQ-M x. -S 3 x 3 Single cting, Spring Extend Cylinder model -T -T -T -T -T -T -T -T C.... D 3 Mounting bolt part no. CQ-M3 x x CQ-M3 x x CQ-M x x CQ-M x x 3 Material: Chromium molybdenum steel Surface treatment: Zinc chromated Single cting, Spring Return Cylinder model C D Mounting bolt part no. CDQS-S CQ-M3 x. -S 3 x 3 CDQS-S CQ-M3 x. -S 3 x 3 CDQS-S 3 CQ-M x 3. -S x CDQS-S CQ-M x. -S Single cting, Spring Extend Cylinder model C D Mounting bolt part no. CDQS-T CQ-M3 x. -T 3 x 3 CDQS-T CQ-M3 x. -T 3 x 3 CDQS-T 3 CQ-M x 3. -T x CDQS-T CQ-M x. -T x Material: Chromium molybdenum steel Surface treatment: Zinc chromated

31 Compact Cylinder: Standard Type Single cting, Single Rod Series Construction Single acting, Spring return w t! r o! q e Single acting, Spring extend w t!3!! e! q o Single acting, Spring return/with auto switch (uilt-in magnet) ø, t w! r q oi!! e Single acting, Spring extend/with auto switch (uilt-in magnet) ø,!3tw! yi!! e!q o ø, ø, w t! r o q!! e w t!3!!! e! q o Component Parts No. Description Cylinder tube Collar 3 Piston Piston rod Retaining ring Retaining ring Rod end nut Spacer for switch type Return spring Plug with fixed orifice Magnet Centering location ring 3 Rod seal Piston seal Tube gasket Material luminum alloy luminum alloy luminum alloy Stainless steel Stainless steel Carbon tool steel Carbon tool steel Carbon steel luminum alloy Piano wire lloy steel luminum alloy NR NR NR Note Hard anodized nodized Single acting, Spring return Single acting, Spring extend Phosphate coated Nickel plated Nickel plated Chromated Zinc chromated Nickel plated nodized Single acting, Spring return Single acting, Spring extend u With boss on head end! J JCQ CQ RQ CQM CQU MU Replacement Parts/Seal Kit Single acting, Spring return Kit no. Contents -S-PS -S-PS -S-PS Set of nos. above! -S-PS Seal kit includes!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) Replacement Parts/Seal Kit Single acting, Spring extend Kit no. Contents -T-PS -T-PS -T-PS -T-PS Set of nos. above!3,!,! Seal kit includes!3,!,!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) D- -X Technical Data

32 Series Dimensions: ø to ø/single cting, Spring Return asic type (Through-hole/oth ends tapped common): /CDQS ø ø x x øo counterbore R H thread effective depth C x x O effective depth R Note) uto switch Minimum lead wire bending radius M x. x øn through Flat washer pcs. ø, ø Width across flats MM With boss on head end øth H C X G asic Type, Without auto switch ST.. 3. Rod End Male Thread With auto switch ST ST ST ST ST ST ST C 3 D E 3... F.. MM M x. M x. M x. M x. H M3 x. M x. M x. M x. Note) For basic type ø and ø with stroke, through-hole is threaded over the entire length. For basic type ø, ø with and stroke, through-hole is threaded over the entire length. With auto switch (uilt-in magnet)/ø; stroke. For details about the rod end nut and accessory brackets, refer to page. C H I 3 3 X.. K With oss on Head End.. Note) With boss on rod end : Option (Suffix "-XC3" to the end of part number.) M.. N G Th O M x. M x. M x. M x O R R T....

33 Compact Cylinder: Standard Type Single cting, Single Rod Series Dimensions: ø to ø/single cting, Spring Return Foot type: /CDQS X Z H Y x ød Special cap bolt + Stroke T X Y Y X G S + Stroke + Stroke Foot Type, Without auto switch With auto switch S.3.3 S D G H T X Y Z X Foot bracket material: Carbon steel Surface treatment: Nickel plated Y... Compact foot type: C/CDQSC X Z H Y x ød T Y Special cap bolt + Stroke X X Y S + Stroke + Stroke Compact Foot Type, Without auto switch With auto switch S S D H T X Y Z X Compact foot bracket material: Carbon steel Surface treatment: Zinc chromated Y... Rod side flange type: F/CDQSF Rod end nut Head side flange type: G/CDQSG + Stroke + Stroke x øfd Rod end nut + Stroke + Stroke x øfd Rod Side Flange Type, Without auto switch Head Side Flange Type, With auto switch Without auto switch With auto switch FD.... FT.. FV 3 FX FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated Flange bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page. FD.... FT.. FV 3 FX FZ J JCQ CQ RQ CQM CQU MU D- -X Technical Data

34 Series Dimensions: ø to ø/single cting, Spring Return Double clevis type: D/CDQSD + Stroke C + Stroke + Stroke Cap bolt øcd hole H Rod d Double Clevis Type, Without auto switch..... C With auto switch C 3... C CD CT CW CX CZ Double clevis bracket material: Carbon steel Surface treatment: Nickel plated For details about the double clevis pivot bracket, refer to page. For details about the rod end nut and accessory brackets, refer to page RR Rod end nut

35 Compact Cylinder: Standard Type Single cting, Single Rod Series Dimensions: ø to ø/single cting, Spring Extend asic type (Through-hole/oth ends tapped common): /CDQS ø ø x x øo counterbore R H thread effective depth C x x O effective depth R Note) M x. uto switch Minimum lead wire bending radius x øn through Flat washer pcs. ø, ø Rod End Male Thread C H 3 Width across flats MM H C X ST. 3.. ST.. 3. MM M x. M x. M x. M x. X.. With boss on head end With oss on Head End G. Th Note) With boss on rod end : Option (Suffix "-XC3" to the end of part number.) G øth J JCQ CQ RQ CQM CQU MU asic Type, Without auto switch ST With auto switch ST ST ST ST ST ST ST C D E 3 H M3 x. M x. M x. M x. Note) For basic type ø and ø with stroke, through-hole is threaded over the entire length. For basic type ø, ø with and stroke, through-hole is threaded over the entire length. With auto switch (uilt-in magnet)/ø; stroke. For details about the rod end nut and accessory brackets, refer to page. I 3 3 K ST... ST M.. N O M x. M x. M x. M x. O.. Q R R T.... D- -X Technical Data

36 Series Dimensions: ø to ø/single cting, Spring Extend Foot type: /CDQS X Z H Y x ød + Stroke Special cap bolt + Stroke T X Y S + Stroke + (Stroke) Y X G Foot Type ,.. 3. Without auto switch S.. D.... G.. H With auto switch S.. T X Y. 33. Z X.. Y... Foot bracket material: Carbon steel Surface treatment: Nickel plated + Stroke Compact foot type: C/CDQSC X Z H Y x ød Rod side flange type: F/CDQSF x øfd + Stroke + Stroke Special cap bolt + Stroke Y X S + Stroke + (Stroke) X Y + Stroke + Stroke + (Stroke) T Compact Foot Type Without auto switch With auto switch Rod Side Flange Type, , S Without auto switch With auto switch FD FT FV 3 S.... D.... H T X.. Y. 33. Z 3 FX FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated X Y... Compact foot bracket material: Carbon steel Surface treatment: Zinc chromated Rod end nut + Stroke Head side flange type: G/CDQSG + Stroke + Stroke + (Stroke) x øfd Head Side Flange Type, Without auto switch With auto switch FD.... FT.. FV 3 FX FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page. + Stroke Rod end nut

37 Compact Cylinder: Standard Type Single cting, Single Rod Series Dimensions: ø to ø/single cting, Spring Extend Double clevis type: D/CDQSD + Stroke + Stroke C + (Stroke) + (Stroke) + Stroke Cap bolt øcd hole H Rod d Double Clevis Type, C CD Without auto switch..... C CT With auto switch C 3... CW CX. CZ RR. Double clevis bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page. J JCQ CQ RQ CQM CQU MU 3 D- -X Technical Data

38 Compact Cylinder: Non-rotating Rod Type Double cting, Single Rod K Series ø, ø, ø, ø With auto switch With auto switch (uilt-in magnet) Mounting type Through-hole/oth ends tapped common (Standard) Foot type C Compact foot type F Rod side flange type G Head side flange type D Double clevis type Mounting brackets are shipped together (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to Mounting olt for K on page. K D CDQSK D mm mm mm mm Cylinder stroke Standard Stroke Standard stroke,,,,,,,,,,,,, 3,,, For Manufacture of Intermediate Strokes, refer to page. ction D Double acting MW pplicable uto Switches/Refer to pages to for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (-color indicator) Water resistant (-color indicator) Electrical entry 3-wire (NPN) 3-wire (PNP) V, V -wire V 3-wire (NPN) Grommet Yes 3-wire (PNP) V V, V -wire V 3-wire (NPN) 3-wire (PNP) V, V -wire V 3-wire Yes (NPN equivalent) V Grommet Indicator light No oad voltage Wiring (Output) DC C -wire V How to Order V V V or less MNV MN MPV MP MV M MNWV MNW MPWV MPW MWV MW MNV MN MPV MP MV M V 3V V 3 Made to Order Refer to page for details. Number of auto switches Nil S n pcs. pc. n pcs. uto switch Nil Without auto switch Refer to the table below for the applicable auto switch model. ody option Nil M F Standard (Rod end female thread) oss on head side uto switch model Perpendicular In-line Water resistant type auto switches can be mounted on the above models, but in such case cannot guarantee water resistance. Consult with regarding water resistant types with the above model numbers. m type lead wire is only applicable to D-3. uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDQSK-D ead wire length (m). (Nil) (M) 3 () (Z) Pre-wired connector pplicable load ead wire length symbols:. m Nil (Example) MNW Solid state auto switches marked with are produced upon receipt of order. m M (Example) MNWM 3 m (Example) MNW m Z (Example) MNWZ Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages and. uto switches are shipped together (not assembled). Note) There is the case D- V/M V/M WV/M V type auto switches cannot be mounted on the port surface, depending on the cylinder s stroke and the fitting size for piping. Consult with for details. Combination of body options is available. FM IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC

39 Compact Cylinder: Non-rotating Rod Type Double cting, Single Rod K Series Standard Specifications ction Double acting, Single rod Fluid ir ubrication Not required (Non-lube) Proof pressure. MPa Maximum operating pressure. MPa Minimum operating pressure. MPa. MPa mbient and fluid temperature Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Cushion None Symbol Without cushion Rod end thread Stroke length tolerance Piston speed Female thread +. mm to mm/s llowable kinetic energy (J)..3.. Rod non-rotating accuracy ± ±. Made to Order: Individual Specifications (For details, refer to page.) Theoretical Output OUT IN (N) Symbol Specifications -X With concave shape end boss on the cylinder tube head side Rod width across flats ction Piston area (mm ) Operating pressure (MPa).3.. Made to Order Specifications (For details, refer to pages 3 to.). IN OUT Symbol Specifications -X Change of Rod End Shape -XC Piston rod and rod end nut made of stainless steel -XC djustable stroke cylinder/djustable extension type -XC djustable stroke cylinder/djustable retraction type -XC Dual stroke cylinder/double rod type -XC Dual stroke cylinder/single rod type... IN OUT IN OUT IN OUT 3 3 ody Option Description pplication vailable for all non-rotating rod type. Mounting racket Part No. Foot () K- K- K- K- Compact foot () Flange Double clevis K-C K-F K-D K-C K-F K-D K-C K-F K-D K-C K-F K-D Note ) When ordering foot and compact foot brackets, order pieces per cylinder. Note ) Parts belonging to each bracket are as follows. Foot, Compact foot, Flange type: ody mounting bolt Double clevis type: Clevis pin, Type C retaining ring for axis, ody mounting bolt. Manufacture of Intermediate Stroke Standard stroke Description Part no. Example Description Spacer is installed in the standard stroke body. Refer to pages to for cylinders with auto switches. Refer to How to Order for the standard model no. (page ). Intermediate strokes in mm increments are available by using spacers with standard stroke cylinders., to, to Part no.: KD K-D with 3 mm width spacer inside. dimension is. mm. Minimum auto switch mounting stroke Proper auto switch mounting position (detection at stroke end) and mounting height Operating range J JCQ CQ RQ CQM CQU MU Moisture Control Tube IDK Series When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. For details, refer to the IDK series in the est Pneumatics No.. D- -X Technical Data

40 K Series Weight/Without uto Switch 3 3 Cylinder stroke 3 (g) Calculation: (Example) KF-DM Cylinder weight: K-D g dditional weight: g : Rod side flange type g g Weight/With uto Switch (uilt-in magnet) (g) Cylinder stroke dditional Weight (g) Male thread Nut. 3 With boss on head end..3 3 Foot type (Including mounting bolt) Compact foot type (Including mounting bolt) Rod side flange type (Including mounting bolt) Head side flange type (Including mounting bolt) 3 Double clevis type (Including pin, retaining ring, bolt) 3

41 Compact Cylinder: Non-rotating Rod Type Double cting, Single Rod K Series Construction asic type With auto switch (uilt-in magnet) ø ø! w! r q!3 e o i! w! r q ty!3 e o i ø, ø, ø ø! u w! r q!3 e o i! u w! r q t y!3 e o i! With boss on head end! ø, ø! w u! r q y!3 e o i Component Parts No. Description Material Note 3 Cylinder tube Rod cover Piston Piston rod Spacer for switch type Magnet luminum alloy luminum alloy luminum alloy Stainless steel luminum alloy Hard anodized nodized Chromated Non-rotating guide Oil impregnated sintered alloy ø, ø and ø Hexagon socket head cap screw Plain washer Rod end nut Centering location ring lloy steel Rolled steel Carbon steel luminum alloy Nickel plated Nickel plated Nickel plated nodized Rod seal 3 Piston seal Tube gasket NR NR NR Replacement Parts/Seal Kit Kit no. Contents K-PS K-PS K-PS Set of nos. above!,!3,!. K-PS Seal kit includes!,!3,!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) llowable rotational torque (N m) or less ø. Precautions Operating Precautions CQ Caution. ny kind of operation producing rotational torque to piston rod RQ must be considered. The non-rotating guide would be deformed and the accuracy would be compromised. CQM Refer to the table below for rotation torque allowance. CQU ø. ø. ø.. oad to piston rod must always be in an axial direction. 3. When a workpiece is secured to the end of the piston rod, ensure that the piston rod is retracted entirely, and place a wrench on the portion of the rod that protrudes beyond the section. lso, tighten by giving consideration to prevent the tightening torque from being applied to the non-rotating guide. J JCQ MU D- -X Technical Data

42 K Series Mounting olt for K Mounting method: Mounting bolt for through-hole mounting type of K is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x pcs. Head side mounting type Rod side mounting type Mounting bolt Mounting bolt Note) When mounting a cylinder with through-hole, be sure to use the attached plain washer. Mounting olt for CDQSK Mounting method: Mounting bolt for through-hole mounting type of CDQSK is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x pcs. Head side mounting type Rod side mounting type Mounting bolt Mounting bolt Note) When mounting a cylinder with through-hole, be sure to use the attached plain washer. Cylinder model K-D -D C D Mounting bolt part no. CQ-M3 x x C' D' 3 Mounting bolt part no. CQ-M3 x x 3 -D 3 x 3 x.. -D x x -D -D K-D -D x x CQ-M3 x x 3 x x CQ-M3 x x 3 -D 3 x 3 x.. -D x x -D -D K-D -D -D -D -D -D -3D -D -D -D K-D -D -D -D. 3 3 x x CQ-M x x x 3 x x x x x x x CQ-M x x 3 x x. 3 3 x x CQ-M x x 3 x x x x x x x x CQ-M x 3 x x x -D x x.. -D x x -3D -D -D -D x x x x x x x x Material: Chromium molybdenum steel Surface treatment: Zinc chromated Cylinder model CDQSK-D -D C D 3 Mounting bolt part no. CQ-M3 x x 3 C' D' 3 Mounting bolt part no. CQ-M3 x 3 x -D x x.. -D x x -D -D CDQSK-D -D 3 x x CQ-M3 x x 3 3 x x CQ-M3 x 3 x -D x x.. -D x x -D -D CDQSK-D -D -D -D -D -D -3D -D -D -D CDQSK-D -D -D -D. 3 x x CQ-M x 3 x x x x x x x x x CQ-M x x x x. x x CQ-M x x x x x x x x x x CQ-M x x x x -D x x.. -D x x -3D -D -D -D x x x x x x x x Material: Chromium molybdenum steel Surface treatment: Zinc chromated

43 Compact Cylinder: Non-rotating Rod Type Double cting, Single Rod K Series Dimensions: ø to ø asic type (Through-hole/oth ends tapped common): K/CDQSK For the auto switch mounting position and its mounting height, refer to page. ø ø x x øo counterbore x x O effective depth R Note) H thread effective depth C x M x. uto switch Minimum lead wire bending radius Flat washer pcs. Width across flats x øn through + Stroke + Stroke ø, ø asic Type to to to to Without auto switch With auto switch Width across flats MM Rod End Male Thread C E 3 F.. 3 H M3 x. M x. M x. M x. I Note) For basic type ø and ø with stroke, through-hole is threaded over the entire length. For basic type ø with to stroke, through-hole is threaded over the entire length. For basic type ø with and stroke, through-hole is threaded over the entire length. Note) With auto switch (uilt-in magnet): ø; stroke For details about the rod end nut and accessory brackets, refer to page. H C X C H MM M x. M x. M x. M x. K X.. M.. N With boss on head end G With oss on Head End O M x. M x. M x. M x. G.. O.. Q.. 3 Th R R øth T.. J JCQ CQ RQ CQM CQU MU D- -X Technical Data

44 K Series Dimensions: ø to ø Foot type: K/CDQSK X Z H Y x ød X Y Special cap bolt + Stroke T S + Stroke + Stroke Y X G Foot Type to to to to Without auto switch.3.3 S With auto switch.3.3 S D G H T X Y Z X Foot bracket material: Carbon steel Surface treatment: Nickel plated Y.. Compact foot type: KC/CDQSKC X Z H Y T x ød Y X Special cap bolt + Stroke S + Stroke + Stroke X Y Compact Foot Type Without auto switch With auto switch to to to to S S D H T X Y Z X Compact foot bracket material: Carbon steel Surface treatment: Zinc chromated Y... Rod side flange type: KF/CDQSKF FX FZ FV x øfd FT + Stroke + Stroke Rod Side Flange Type to to to to Without auto switch With auto switch FD... FT.. FV 3 FX FZ. 3. Flange bracket material: Carbon steel Surface treatment: Nickel plated Rod end nut Head side flange type: KG/CDQSKG + Stroke + Stroke x øfd Head Side Flange Type to to to to Without auto switch With auto switch FD... FT.. FV 3 FX FZ.. Flange bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page... Rod end nut

45 Compact Cylinder: Non-rotating Rod Type Double cting, Single Rod K Series Dimensions: ø to ø Double clevis type: KD/CDQSKD + Stroke C + Stroke + Stroke Cap bolt øcd hole H Rod d Double Clevis Type to to to to Without auto switch... C With auto switch.. 3. C C CD CT CW CX CZ. Double clevis bracket material: Carbon steel Surface treatment: Nickel plated For details about the double clevis pivot bracket, refer to page. For details about the rod end nut and accessory brackets, refer to page RR Rod end nut J JCQ CQ RQ CQM CQU MU 3 D- -X Technical Data

46 Compact Cylinder: Non-rotating Rod Type Double cting, Double Rod KW Series ø, ø, ø, ø How to Order KW D With auto switch CDQSKW D MW With auto switch (uilt-in magnet) C F Mounting type Through-hole/oth ends tapped common (Standard) Foot type Compact foot type Flange type Mounting brackets are shipped together (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to Mounting olt for KW on page 3. Made to Order Refer to page 33 for details. Number of auto switches Nil S n pcs. pc. n pcs. uto switch Nil Without auto switch Refer to the table below for the applicable auto switch model. mm mm mm mm ody option Nil M Standard (Rod end female thread) Standard Stroke,, Cylinder stroke Standard stroke,,,,,,,,,,, 3,,, ction D Double acting uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDQSKW-D pplicable uto Switches/Refer to pages to for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (-color indicator) Water resistant (-color indicator) Electrical entry Indicator light oad voltage Wiring (Output) DC C 3-wire (NPN) 3-wire (PNP) -wire V, V V 3-wire (NPN) Grommet Yes 3-wire (PNP) -wire 3-wire (NPN) 3-wire (PNP) -wire 3-wire Yes (NPN equivalent) Grommet V V, V V V, V V V No -wire V V V V or less uto switch model Perpendicular MNV MN MPV MP MV M MNWV MNW MPWV MPW MWV MW MNV MN MPV MP MV M V 3V V In-line 3 Water resistant type auto switches can be mounted on the above models, but in such case cannot guarantee water resistance. Consult with regarding water resistant types with the above model numbers. m type lead wire is only applicable to D-3. ead wire length (m). (Nil) (M) 3 () (Z) Pre-wired connector pplicable load ead wire length symbols:. m Nil (Example) MNW Solid state auto switches marked with are produced upon receipt of order. m M (Example) MNWM 3 m (Example) MNW m Z (Example) MNWZ Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages and. uto switches are shipped together (not assembled). Note) There is the case D- V/M V/M WV/M V type auto switches cannot be mounted on the port surface, depending on the cylinder s stroke and the fitting size for piping. Consult with for details. 3 IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC

47 Compact Cylinder: Non-rotating Rod Type Double cting, Double Rod KW Series Symbol Without cushion Specifications ction Fluid ubrication Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Cushion Rod end thread Stroke length tolerance Piston speed llowable kinetic energy (J) Rod non-rotating accuracy Double acting, Single rod ir Not required (Non-lube). MPa. MPa. MPa. MPa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) None Female thread +. mm to mm/s..3.. ± ±. Made to Order: Individual Specifications (For details, refer to page ) Symbol Specifications -X33 Intermediate stroke of double rod cylinder Made to Order Specifications (For details, refer to pages 3 to.) Symbol Specifications -X Change of rod end shape Piston rod, retaining ring, rod end nut -XC made of stainless steel ody Option Description pplication vailable for all non-rotating rod type. Mounting racket Part No. Foot () Compact foot () Flang K- K- K- K- K-C K-C K-C K-C K-F K-F K-F K-F Note ) When ordering foot and compact foot brackets, order pieces per cylinder. Note ) Parts belonging to each bracket are as follows. Foot, Compact foot, Flange type: ody mounting bolt Theoretical Output Rod width across flats.... Piston area (mm ) Refer to pages to for cylinders with auto switches. (N) Operating pressure (MPa) Minimum auto switch mounting stroke Proper auto switch mounting position (detection at stroke end) and mounting height Operating range J JCQ CQ RQ CQM CQU MU Moisture Control Tube IDK Series When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. For details, refer to the IDK series in the est Pneumatics No.. 33 D- -X Technical Data

48 KW Series Weight/Without uto Switch 3 Cylinder stroke Weight/With uto Switch (uilt-in magnet) 3 3 (g) 3 (g) Precautions Operating Precautions Warning. Do not apply the reverse torque to the piston rods sticking out from both sides of this cylinder at the same time. The torque makes connection threads inside loosen, which may cause an accident or malfunction. Install or remove a load while the piston rod width across flats are secured. Do not fix the other side of piston rod width across flat and apply the reverse torque dditional Weight (g) Male thread Nut Foot type (Including mounting bolt) Compact foot type (Including mounting bolt) Rod side flange type (Including mounting bolt). 3 Calculation: (Example) KWF-DM Cylinder weight: KW-D g dditional weight: g : Rod side flange type g g Caution. ny kind of operation producing rotational torque to piston rod must be considered. The non-rotating guide would be deformed and the accuracy would be compromised. Refer to the table below for rotation torque allowance. llowable rotational torque (N m) or less ø. ø. ø. ø.. oad to piston rod must always be in an axial direction. Retaining Ring Installation/Removal Caution. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring).. Even if a proper plier (tool for installing type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. 3

49 Compact Cylinder: Non-rotating Rod Type Double cting, Double Rod KW Series Construction asic type ø With auto switch (uilt-in magnet) ø ø, ø, ø ø ø, ø Component Parts No. 3 3 Description Cylinder tube Rod cover Collar Piston Piston rod Piston rod Spacer for switch type Magnet Retaining ring Non-rotating guide Hexagon socket head cap screw Plain washer Rod end nut Material luminum alloy luminum alloy luminum alloy luminum alloy Stainless steel Stainless steel luminum alloy Carbon tool steel Oil impregnated sintered alloy lloy steel Rolled steel Carbon steel Rod seal for non-rotating Rod seal Piston seal Tube gasket NR NR NR NR Note Hard anodized nodized nodized Chromated Phosphate coated ø, ø and ø Nickel plated Nickel plated Nickel plated J JCQ CQ RQ CQM CQU MU Replacement Parts/Seal Kit Kit no. Contents KW-PS KW-PS KW-PS Set of nos. above!,!,!,!. KW-PS Seal kit includes!,!,!,!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) 3 D- -X Technical Data

50 KW Series Mounting olt for KW Mounting method: Mounting bolt for through-hole mounting type of KW is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x pcs. Round rod side mounting Non-rotating rod side mounting Mounting bolt C' D' Note) When mounting a cylinder with through-hole, be sure to use the attached plain washer. Mounting olt for KW Non-rotating rod side mounting Mounting bolt C' D' D D C C Mounting bolt Mounting method: Mounting bolt for through-hole mounting type of CDQSKW is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x3 pcs. Round rod side mounting Note) When mounting a cylinder with through-hole, be sure to use the attached plain washer. 3 Mounting bolt Cylinder model KW-D -D C D Mounting bolt part no. CQ-M3 x x 3 C' D' 3 Mounting bolt part no. CQ-M3 x 3 x -D 3 x x.. -D x x -D -D KW-D -D x x CQ-M3 x x 3 3 x x CQ-M3 x 3 x -D 3 x x.. -D x x -D -D KW-D -D -D -D -D -D -3D -D -D -D KW-D -D -D -D 3 3 x x CQ-M x 3 x x x x x x x x x CQ-M x 3 x x x 3 3 x x CQ-M x x x x x x x x x x CQ-M x x x x -D x x -D x x -3D -D -D -D x x x x x x x x Material: Chromium molybdenum steel Surface treatment: Zinc chromated Cylinder model CDQSKW-D -D C D 3 Mounting bolt part no. CQ-M3 x 3 x C' D' 3 Mounting bolt part no. CQ-M3 x x -D x x.. -D x x -D -D CDQSKW-D -D 3 x x CQ-M3 x 3 x 3 x x CQ-M3 x x -D x x.. -D x x -D -D CDQSKW-D -D -D -D -D -D -3D -D -D -D CDQSKW-D -D -D -D 3 x x CQ-M x x x x x x x x x x CQ-M x x x x x x x x x x x x x x x x CQ-M x x x x -D x x -D x x -3D -D -D -D x x x x x x x x Material: Chromium molybdenum steel Surface treatment: Zinc chromated

51 Compact Cylinder: Non-rotating Rod Type Double cting, Double Rod KW Series Dimensions: ø to ø asic type (Through-hole/oth ends tapped common): KW/CDQSKW ø For the auto switch mounting position and its mounting height, refer to page. ø x x øo counterbore x x O effective depth R øi H thread effective depth C M E T Width across flats K Q uto switch Minimum lead wire bending radius F x M x. Width across flats K ød M E Flat washer pcs. R R + Stroke + (Stroke) x øn through + Stroke ø, ø Width across flats MM Width across flats MM J H H C X + (Stroke) C X + Stroke JCQ CQ Rod End Male Thread Without auto switch With auto switch 3 3 C H... MM M x. M x. M x. M x. X.. RQ CQM CQU MU asic Type Without auto switch With auto switch to to to to C D E 3 F.. H M3 x. M x. M x. M x. I 3 3 K.... Note ) For basic type ø and ø with stroke, through-hole is threaded over the entire length. Note ) The positions of width across flats (K) on both sides are not the same. For details about the rod end nut and accessory brackets, refer to page. K M.. N O M x. M x. M x. M x. O.. Q.. 3 R R T.. 3 D- -X Technical Data

52 KW Series Dimensions: ø to ø Foot type: KW/CDQSKW + Stroke + Stroke Special cap bolt Y H X Z x ød X Y Y X S + Stroke + (Stroke) T G + (Stroke) + Stroke Foot Type to to to to Without auto switch 3 3 S Compact foot type KWC/CDQSKWC With auto switch S 3. D. G. H T X 3 Y. Z Foot bracket material: Carbon steel Surface treatment: Nickel plated X. Y.. Special cap bolt + Stroke + Stroke H T Y X Z x ød Y X S + Stroke + (Stroke) X Y Compact Foot Type to to to to Without auto switch S With auto switch S.... For details about the rod end nut and accessory brackets, refer to page (Stroke) + Stroke D H T X Y Z Compact foot bracket material: Carbon steel Surface treatment: Zinc chromated X Y...

53 Compact Cylinder: Non-rotating Rod Type Double cting, Double Rod KW Series Dimensions: ø to ø Flange type: KWF/CDQSKWF FV FX FZ x øfd FT + Stroke + (Stroke) + Stroke + (Stroke) 3 + Stroke Flange Type to to to to Without auto switch 3 3 With auto switch FD.... For details about the rod end nut and accessory brackets, refer to page. Note ) The positions of piston rod width across flats (right side) are not constant. FT.. FV 3 FX FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated J JCQ CQ RQ CQM CQU MU 3 D- -X Technical Data

54 Compact Cylinder: nti-lateral oad Type S Series ø, ø, ø, ø How to Order S D C With auto switch CDQS S D C MW C F G D With auto switch (uilt-in magnet) Mounting type Through-hole/oth ends tapped common (Standard) Foot type Compact foot type Rod side flange type Head side flange type Double clevis type Mounting brackets are shipped together (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to Mounting olt for S on page. S Cushion nti-lateral load type mm mm mm mm Cylinder stroke Standard Stroke Standard stroke,,,,,,,,,,,,, 3,,, For Manufacture of Intermediate Strokes, refer to page. Made to Order Refer to page for details. Number of auto switches Nil S n pcs. pc. n pcs. uto switch Nil Without auto switch Refer to the table below for the applicable auto switch model. ody option Nil Standard (Rod end female thread) M Cushion C Rubber bumper ody option Nil Standard F With boss on head end ction D Double acting uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDQSS-D pplicable uto Switches/Refer to pages to for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (-color indicator) Water resistant (-color indicator) Electrical entry 3-wire (NPN) 3-wire (PNP) V, V -wire V 3-wire (NPN) Grommet Yes 3-wire (PNP) V V, V -wire V 3-wire (NPN) 3-wire (PNP) V, V -wire V 3-wire Yes (NPN equivalent) V Grommet Indicator light No oad voltage Wiring (Output) DC C -wire V V V V or less uto switch model Perpendicular MNV MN MPV MP MV M MNWV MNW MPWV MPW MWV MW MNV MN MPV MP MV M V 3V V In-line 3 Water resistant type auto switches can be mounted on the above models, but in such case cannot guarantee water resistance. Consult with regarding water resistant types with the above model numbers. m type lead wire is only applicable to D-3. ead wire length (m). (Nil) (M) 3 () (Z) Pre-wired connector pplicable load ead wire length symbols:. m Nil (Example) MNW Solid state auto switches marked with are produced upon receipt of order. m M (Example) MNWM 3 m (Example) MNW m Z (Example) MNWZ Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages and. uto switches are shipped together (not assembled). Note) There is the case D- V/M V/M WV/M V type auto switches cannot be mounted on the port surface, depending on the cylinder s stroke and the fitting size for piping.consult with for details. IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC

55 Compact Cylinder: nti-lateral oad Type S Series Symbol Rubber bumper Standard Specifications ction Fluid ubrication Proof pressure Maximum operating pressure Double acting, Single rod ir Not required (Non-lube). MPa. MPa Minimum operating pressure. MPa. MPa Without auto switch: to C (No freezing) mbient and fluid temperature Cushion Rod end thread With auto switch: to C (No freezing) Rubber bumper Female thread Stroke length tolerance +. mm Piston speed to mm/s llowable kinetic energy (J).3... Stroke length tolerance does not include the deflection of the bumper. Made to Order: Individual Specifications (For details, refer to pages and.) Symbol Specifications -X Fluororubber seals -X With concave shape end boss on the cylinder tube head side Made to Order Specifications (For details, refer to pages 3 to.) Symbol Specifications -X Change of Rod End Shape -X Intermediate stroke (Using exclusive body) Piston rod, retaining ring, rod end nut -XC made of stainless steel -XC Grease for food processing equipment ody Option Description pplication vailable for Double acting, Single rod models. Mounting racket Part No. Foot () Compact foot () Flange Double clevis - -C -F -D - -C -F -D - -C -F -D - -C -F -D Note) When ordering foot and compact foot brackets, order pieces per cylinder. Note) Parts belonging to each bracket are as follows. Foot, Compact foot, Flange type: ody mounting bolt Double clevis type: Clevis pin, type C retaining ring for axis, ody mounting bolt Theoretical Output Rod size Operating direction IN OUT IN OUT IN OUT IN OUT Manufacture of Intermediate Stroke Standard stroke Description Part no. Example Description Piston area (mm ) Refer to pages to for cylinders with auto switches. OUT IN (N) Operating pressure (MPa) Spacer is installed in the standard stroke body. Refer to How to Order for the standard model no. (page ). Intermediate strokes in mm increments are available by using spacers with standard stroke cylinders., to, to Part no.: SD S-D with 3 mm width spacer inside. dimension is. mm. Minimum auto switch mounting stroke Proper auto switch mounting position (detection at stroke end) and mounting height Operating range J JCQ CQ RQ CQM CQU MU Moisture Control Tube IDK Series When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. For details, refer to the IDK series in the est Pneumatics No.. D- -X Technical Data

56 S Series Weight/Without uto Switch 3 3 Cylinder stroke Weight/With uto Switch (uilt-in magnet) dditional Weight 3 3 Male thread Nut With boss on head end Foot type (Including mounting bolt) Compact foot type (Including mounting bolt) Rod side flange type (Including mounting bolt) Head side flange type (Including mounting bolt) Double clevis type (Including pin, retaining ring, bolt) Mounting olt for S Mounting method: Mounting bolt for through-hole mounting type of S is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x pcs. Note) When mounting a cylinder with through-hole, be sure to use the attached plain washer. Cylinder stroke Cylinder model SDC DC DC DC DC DC SDC DC DC DC DC DC SDC DC DC DC Mounting olt for CDQSS with uto Switch Mounting method: Mounting bolt for through-hole mounting type of CQQSS is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3x3 pcs. Note) When mounting a cylinder with through-hole, be sure to use the attached plain washer. Mounting bolt Mounting bolt Cylinder model CDQSSDC DC DC DC DC DC CDQSSDC DC DC DC DC DC CDQSSDC DC DC DC C... C D D 3 3 (g) (g) (g) 3 Mounting bolt part no. CQ-M3 x x 3 x x x x CQ-M3 x x 3 x x x x CQ-M x x 3 x x Mounting bolt part no. CQ-M3 x 3 x x x x x CQ-M3 x 3 x x x x x CQ-M x x x x For standard strokes Calculation: (Example) DS-DCM Cylinder weight: S-DC g dditional weight: g : Double clevis type g g Cylinder model SDC DC 3DC DC DC DC SDC DC DC DC DC DC 3DC DC DC DC Cylinder model CDQSSDC DC 3DC DC DC DC CDQSSDC DC DC DC DC DC 3DC DC DC DC C.. C.. D 3 D Mounting bolt part no. CQ-M x x x x x x CQ-M x 3 x x x x x x x x x Material: Chromium molybdenum steel Surface treatment: Zinc chromated Mounting bolt part no. CQ-M x x x x x x CQ-M x x x x x x x x x x Material: Chromium molybdenum steel Surface treatment: Zinc chromated

57 Compact Cylinder: nti-lateral oad Type S Series Construction asic type! t w!! i r q!! e u y With auto switch (uilt-in magnet) ø, ø ø, ø! t w!! i r q u!!! e o! t w!! i r q!!! e o Component Parts No. 3 3 Description Cylinder tube Collar Piston Piston rod Retaining ring Rod end nut Spacer for switch type umper umper ushing Wear ring Magnet Centering location ring Material luminum alloy luminum alloy luminum alloy Stainless steel Carbon tool steel Carbon steel luminum alloy Urethane Urethane Oil-impregnated sintered alloy Resin luminum alloy Rod seal Piston seal Tube gasket NR NR NR Note Hard anodized nodized Phosphate coated Nickel plated Chromated nodized With boss on head end!3 J JCQ CQ RQ CQM CQU MU Replacement Parts/Seal Kit Kit no. Contents -PS -PS -PS Set of nos. above!,!,!. -PS Seal kit includes!,!,!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) D- -X 3 Technical Data

58 S Series Dimensions: ø to ø asic type (Through-hole/oth ends tapped common): S/CDQSS ø ø x x øo counterbore R H thread effective depth C x x O effective depth R Note) x M x. uto switch Minimum lead wire bending radius x øn through Flat washer + Stroke + Stroke ø, ø With boss on head end Width across flats MM øth H C X G Rod End Male Thread 3 C H... MM M x. M x. M x. M x. asic Type Without auto switch With auto switch C D E F H I K to to to M3 x. M x. M x to M x. Note) For basic type to stroke with ø and stroke with ø, through-hole is threaded over the entire length. For details about the rod end nut and accessory brackets, refer to page. X.. M.. With oss on Head End G.. Th Note) With boss on rod end: Option (Suffix -XC3 to the end of part number.) Note that only bore sizes ø and ø are applicable to the long stroke. N O M x. M x. M x. M x. O.. Q.. R R T..

59 Compact Cylinder: nti-lateral oad Type S Series Dimensions: ø to ø Foot type: S/CDQSS H Y + Stroke Special cap bolt Foot Type to to to to Without auto switch With auto switch S S X Z x ød X Y Y X S + Stroke + Stroke T G D G H T X Y Z X Y Foot bracket material: Carbon steel Surface treatment: Nickel plated Compact foot type: CS/CDQSCS X Z H Y x ød T + Stroke Y X X Y S + Stroke + Stroke Special cap bolt Compact Foot Type Without auto switch With auto switch S S to to to to D H T X Y Z X Y Compact foot bracket material: Carbon steel Surface treatment: Zinc chromated Rod side flange type: FS/CDQSFS x øfd + Stroke + Stroke Rod end nut Head side flange type: GS/CDQSGS + Stroke x øfd + Stroke Rod end nut Rod Side Flange Type to to to to FD.... FT.. to to to to FV 3 Head Side Flange Type FD.... FT.. Without auto switch With auto switch FV 3.. FX FZ.. FX FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated Without auto switch With auto switch Flange bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page. J JCQ CQ RQ CQM CQU MU D- -X Technical Data

60 S Series Dimensions: ø to ø Double clevis type: DS/CDQSDS + Stroke C + Stroke + Stroke Rod end nut Cap bolt øcd hole H Rod d Double Clevis Type to to to to C CD Without auto switch With auto switch... CT.. C 3... CW... CX CZ C RR Double clevis bracket material: Carbon steel Surface treatment: Nickel plated For details about the double clevis pivot bracket, refer to page. For details about the rod end nut and accessory brackets, refer to page.

61 Series uto Switch Mounting Proper uto Switch Mounting Position (Detection at stroke end) and Its Mounting Height Double acting: Single rod, Single acting: Single rod, Spring return/spring extend; ong stroke type, nti-lateral load type, Double acting: Double rod) ø a) Mounting b) ø to ø a) Mounting b) D-M, M W, M D-M V, M WV, M V Hs Hs D- D- V Hs Hs D-P3DW ø Hs Proper uto Switch Mounting Position (Detection at stroke end) Double acting: Single rod, Single acting: Single rod, Spring return/spring extend; ong stroke type, nti-lateral load type, Double acting: Double rod) Proper uto Switch Mounting Position uto switch D-M /M W D-M V/M WV/M V D-M D- D- V D-P3DW model W Hs W W Hs Hs Double cting, Single Rod; Single cting, Single Rod, Spring Return/Spring Extend. (.) ong Stroke (.)... nti-lateral oad Type (.) Double cting, Double Rod.... (.) (3.) (.) (3.) (.)... (.) Note ) The product is shipped out of the factory in installation state a). To change the electrical entry direction of the auto switch on the head, refer to installation state b). Note ) Negative figures in the table W indicate an auto switch is mounted inward from the edge of the cylinder body. Note 3) The D-M /M W and M cannot be installed on the single acting: single rod type. Note ) djust the auto switch after confirming the operating conditions in the actual setting. Note ) The D-P3DW is available only for ø of the double acting single rod, long stroke, anti-lateral load and double rod type [ ]: Denotes the values of D-3. ( ): Denotes the values of type T.. [] (. []) [.]. [] 3. [] [-.]. [] [.] [.] [3.]. [3] 3. []. [3] 3. [] 3 [.] [.] [.]. (.) J JCQ CQ RQ CQM CQU MU D- -X Technical Data

62 Series uto Switch Mounting Proper uto Switch Mounting Position (Detection at stroke end) Non-rotating rod ø D- Mounting a) b) ø to ø Mounting a) b) D- V Hs Hs D-M D-M W D-M D-M V D-M WV D-M V Hs Hs Proper uto Switch Mounting Position uto switch D- D- V D-M /M W D-M V/M WV/M V model W Hs W Hs.. () (.). 3.. () ()..... ( ): Denotes the values of D-3. uto switch model D-M W Note ) The product is shipped out of the factory in installation state a). To change the electrical entry direction of the auto switch on the head, refer to installation state b). Note ) djust the auto switch after confirming the operating conditions in the actual setting.

63 uto Switch Mounting Series Operating Range uto switch model D-M /M V D-M W/M WV D-M /M V D- / V. D-P3DW Since this is a guideline including hysteresis, not meant to be guaranteed. (assuming approximately ±% dispersion.) There may be the case it will vary substantially depending on an ambient environment. 3.. Minimum uto Switch Mounting Stroke No. of auto switch mounted pc. pcs. D-M V D-M WV D-M V D- () D- V D-M () () D-M W D-M () () D-P3DW Note ) Note ) The D-M /M W/M and P3DW cannot be installed on the single acting: single rod type. Note ) vailable only for ø. Note 3) The dimension stated in ( ) shows the minimum mountable stroke when the auto switch does not project from the end face of the cylinder body and the lead wire bending space is not hindered. (Refer to the figure below.) The auto switch needs to be ordered separately. Precautions e sure to read this before handling the products. Refer to back page for Safety Instructions and pages 3 to for ctuator and uto Switch Precautions. If the cylinder is used in an application in which a magnetic material is placed in close contact around the cylinder as shown in the graph on the right (including cases in which even one of the sides is in close contact) the operation of auto switches could become unstable. Therefore, please check with for this type of application. Magnetic substance (Iron plate, etc.) Magnetic substance (Iron plate, etc.) Other than the applicable auto switches listed in How to Order, the following auto switches can be mounted. Normally closed (NC = b contact), solid state auto switch (D-FG/FH type, and D-F type) are also available. For details, refer to pages and 3. For solid state auto switches, auto switches with a pre-wired connector are also available. Refer to pages and for details. J JCQ CQ RQ CQM CQU MU D- -X Technical Data

64 Series Made to Order: Individual Specifications Please contact for detailed dimensions, specifications and lead times. Special Piston Rod End for Double Rod Type Cylinder Symbol -X3 Male thread is used at one piston rod end of double rod type cylinder and female thread is used at the other end. C QSW Mounting Stroke D X3 Specifications: Same as standard type. Note) Please contact for mounting bracket. D in the case of -3 Piston rod end Male thread, Female thread + (Stroke) Symbol pplicable stroke 3. (.) () Note ) pplicable stroke is available in mm increments. Note ) ( ): Denotes the dimensions with auto switch. () to to. (.) Fluororubber for Seals Symbol -X Material for seals is changed to fluororubber. C QS Standard model no. X ll series variations except non-rotating piston rod type of the series is available. Specifications are the same as for each variation of. Fluororubber for seals 3 ong Stroke of djustable Extension Stroke Cylinder (-XC) Symbol -X C QS Mounting Stroke D(M) X Specifications are the same as for -XC of the CQ/ series. Refer to Made to Order Common Specifications. ong stroke of XC Note) For the tap mounting type (ø to øwithout switch) and mounting bracket, please contact. ø, ø ø, ø Symbol Stroke ore 3st st st st 3st st st st C pplicable stroke C + Stroke + Stroke. (.). (.).. (.) (.).. (.) (.). (.). (.) () () () () () () () () ,,, ø, ø ø, ø Symbol Stroke ore to st to st to st to st C pplicable stroke + Stroke C + Stroke. (.) (). (.) () () () Note ) ( ): Denotes dimensions with auto switch. Note ) pplicable stroke is available in mm increments. 3 () 3 (). to

65 Made to Order: Individual Specifications Series ong Stroke of djustable Retraction Stroke Cylinder (-XC) Symbol -X C QS Mounting Stroke D (M) X ong stroke of XC Specifications are the same as for -XC of the series. Refer to Made to Order Common Specifications. Note) Please contact for bracket type. Dimensions ø, ø + Stroke + Stroke M Symbol ore M pplicable stroke M x. 3,,,, M x., M x.,,,,, M x.,,,,,,, Note ) Intermediate stroke type (available in mm increments) is for spacer so that dimensions are the same as for each type of,,,,,,, stroke. ø, ø + Stroke Intermediate Stroke of Double Rod Type C QSW Dimensions Standard model no. X33 Specifications: Same as standard type. Note) Please contact for bracket type. + Stroke S + Stroke S + Stroke (S + S) Symbol ore (3) (3) 3 () 3 () () () (3) (3) Stroke S In the case of to stroke mm intervals In the case of to stroke mm intervals Symbol -X33 Stroke S In the case of to stroke mm intervals In the case of to stroke mm intervals Note ) ( ): Denotes the dimensions with auto switch. Note ) Installing a spacer inside the standard cylinder tube, stroke S has mm intervals to controlling intermediate stroke in mm increments. Example) In the case of CDQW-D, stroke S is mm and stroke S is mm. J JCQ CQ RQ CQM CQU MU D- -X Technical Data

66 Series Made to Order: Individual Specifications Please contact for detailed dimensions, specifications and lead times. C QS ong Stroke of Dual Stroke Single Rod Type Stroke S + Stroke S-S DC (M) ong stroke of XC X3 pplicable stroke ø, ø ø, ø Stroke Symbol -X3 Max. stroke S: up to mm Max. stroke S: up to mm mm Specifications are the same as for -XC of the series. Refer to Made to Order Common Specifications. Note) Please contact for tap mounting type and bracket mounting type. Stroke S Stroke S : ø, ø ore Symbol ø ø. (.) + Stroke (S + S). (.) + Stroke (S + S) () + Stroke S () + Stroke S 3 + Stroke S 3 + Stroke S S 3. to S mm 3 to 3. to 3 to : ø, ø Symbol mm ore to to to to ø Stroke () + Stroke S Stroke S Stroke S () + Stroke S. (.) + Stroke S. to to S S ø. (.) + Stroke S. (.) + Stroke S. (3.) + Stroke S to to Note ) ( ): Denotes the dimensions with auto switch. Note ) pplicable stroke is available in mm increments. Cylinder Tube: With Concave oss on Head End Symbol -X C QS Mounting Stroke D (C) (M) S (M) T (M) X With concave boss on head end Specifications are the same as. Note ) : Excluding ø and ø. G Series øth TH G..