How to Order. Manual release type. Lock position. H Head end lock. With rod boot. Nil J K M9NWV M9NW H7C M9PWV M9PW M9BWV M9BW M9NAV M9NA M9PAV M9PA

Transcription

1 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - CDG1 With auto switch (uilt-in magnet) Mounting style asic style L xial foot style F Rod side flange style G Head side flange style U Rod side trunnion style T Head side trunnion style D Clevis style Not available for bore size ø and ø0. esides, trunnion cannot be attached in the side to which an end lock is attached. Note) Mounting brackets are shipped together, (but not assembled). End Lock Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø0 L N 0 L N N Type Rubber bumper ir cushion mm mm mm mm ore size mm mm mm 0 0 mm Cylinder stroke Refer to Standard Stroke on page 3. How to Order H N 0 H N M9W Nil J K Manual release type N L Non-lock type Lock type Lock position H Head end lock R Rod end lock W Double end lock Nylon tarpaulin Heat resistant tarpaulin uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDG1F-0-RL pplicable uto Switches/Refer to pages 9 to 3 for further information on auto switches. Type Special function Reed auto switch Solid state auto switch Electrical entry Grommet Indicator light Wiring (Output) 3-wire (NPN) 3-wire (PNP) Load voltage DC V,1 V C In the case of w/ rod boot, and a foot bracket or rod side flange as a bracket, those parts are to be assembled at the time of shipment. C Number of auto switches Nil pcs. S 1 pc. n n pcs. uto switch Nil Without auto switch For the applicable auto switch model, refer to the table below. uto switch mounting bracket Note) Note) This symbol is indicated when the D-9 or M9 type auto switch is specified.this mounting bracket does not apply to other auto switches (D-C and H, etc.) (Nil) Made to Order Refer to page 3 for details. uto switch model Lead wire length (m) pplicable bore size None Pre-wired pplicable load ø to ø ø, ø0 (Nil) (M) (L) (Z) (N) connector Perpendicular In-line In-line M9NV M9N G9 IC M9PV M9P circuit GP M9V M9 -wire 1 V K9 Connector HC 3-wire M9NWV M9NW (NPN) G9W IC Relay, V V,1 V Diagnostic indication 3-wire M9PWV M9PW circuit PLC (-color indication) (PNP) GPW M9WV M9W Grommet -wire 1 V K9W 3-wire (NPN) M9NV M9N V,1 V IC circuit Water resistant 3-wire (PNP) M9PV M9P (-color indication) M9V M9 -wire 1 V G Diagnostic output (-color indication) -wire (NPN) V,1 V HNF IC circuit 3-wire (Equiv. to NPN) V 9V 9 IC circuit 0 V 93V 93 Grommet None 0 V or less 90V 90 IC circuit Yes -wire V 1 V 0 V, 0 V Relay, None 0 V or less PLC Yes C3C Connector None V or less CC IC circuit Diagnostic indication (-color indication) Grommet Yes 9W Yes Yes Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Consult with SMC regarding water resistant types with the above model numbers. Lead wire length symbols: 0. m Nil (Example) M9NW Solid state auto switches marked with are produced upon receipt of order. 1 m M (Example) M9NWM 3 m L (Example) M9NWL m Z (Example) M9NWZ None N (Example) HCN Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages and. D-9 /M9 auto switches are shipped together (not assembled). (Only auto switch mounting brackets are assembled before shipped.)

2 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Symbol Rubber bumper ir cushion Made to Order Specifications (For details, refer to pages to.) Symbol Specifications -X Change of rod end shape -XC13 uto switch rail mounting Refer to pages 3 to 3 for cylinders with auto switches. Minimum auto switch mounting stroke Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket: Part no. Specifications ore size ction Lubricant Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Stroke length tolerance Cushion Mounting Lock Specifications Standard Stroke Double acting, Single rod Not required (Non-lube) ir 1. MPa 1.0 MPa 0. MPa Without auto switch: to 0 C (No freezing) With auto switch: to 0 C (No freezing) to 00 mm/s to 00 mm/s st st + 1. Up to 00 0 st + 1. mm, to 0 mm st + 1. Up to 10 0 Lock position Head end, Rod end, Double end Holding force (Max.) (N) ø ø 0 ø ø 0 ø 13 ø 1 ø 3 ø0 390 acklash Manual release mm or less Non-lock type, Lock type djust the switch position so that it operates upon movement to both the stroke end and backlash ( mm) positions. ore size, 0 Rod oot Material Symbol Rod boot material J Nylon tarpaulin K Heat resistant tarpaulin 0 Standard stroke (1),,, 0, 1, 1, 0,,, 0, 1, 1, 0, 0, 0 Maximum operating temperature 0 C 1 C Rubber bumper, ir cushion Long stroke 1 to 3 1 to 0 1 to 1 to 0 1 to 1 to 1 to 10 Up to 00 asic style, xial foot style, Rod side flange style Head side flange style, Rod side trunnion style Head side trunnion style, Clevis style (Used for changing the port location by 90.) 0.0 MPa except locking parts. Rod/Head side trunnion styles are not available for bore sizes ø and ø0. Trunnion is not attached for a cover on which lock mechanism is equipped. Maximum manufacturable stroke 10 Note 1) Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note ) Long stroke applies to the axial foot style and the rod side flange style. If other mounting brackets are used, or the length exceeds the long stroke limit, the stroke should be determined based on the stroke selection table in the technical data.(refer to front matter 3.) Maximum ambient temperature for the rod boot itself. End Lock Cylinder Series mm mm 3 CJ1 CJP CJ CJ CM CM CM3 CG3 M M M1 C C CS1 CS D- -X Technical data

3 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Series Construction: With Rubber umper Head end lock Manual release (Non-lock type): Suffix N Rod end lock Component Parts No Description Rod cover Head cover Tube cover Cylinder tube Piston Piston rod ushing Lock piston Lock bushing Lock spring umper Hexagon socket head cap screw Cap Cap Rubber cap M/O knob M/O bolt M/O spring Stopper ring umper umper Replacement Parts/Seal Kit (With lock at single end) ø, ø0 ø, ø Material luminum alloy luminum alloy luminum alloy luminum alloy luminum alloy Carbon steel earing alloy Carbon steel Copper alloy Stainless steel Urethane lloy steel luminum die-casted Carbon steel Synthetic rubber Zinc die-casted lloy steel Steel wire Carbon steel Urethane Urethane Note Clear hard anodized Clear hard anodized Clear hard anodized Hard anodized Chromated Hard chrome plated Hard chrome plated, Heat treated lack zinc chromated lack painted Oxide film treated lack painted lack zinc chromated, Red painted Zinc chromated Zinc chromated ø or larger: the same as bumper Note) In the case of cylinders with auto switches, magnets are installed in the piston. The material is stainless steel on auto switch equipped styles ø and ø. Series ore size Kit no. Contents N-PS N N-PS Set of nos. above Rubber bumper N-PS,,, type and grease pack N-PS Order seal kit in accordance with the bore size. The seal kit includes a grease pack ( g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-0 ( g) No Description Retaining ring Piston gasket Wear ring Rod end nut Rod seal Piston seal Cylinder tube gasket Lock piston seal Piston holder Material Stainless steel NR Resin Rolled steel NR NR NR NR Urethane Replacement Parts/Seal Kit (With lock at double end) Series ore size Kit no. N Rubber bumper type Manual release (Lock type): Suffix L Long stroke N-PS-W N-PS-W N-PS-W N-PS-W 1 13 Note None for ø, ø0 Zinc chromated 1 pc. when using tube cover pcs. for with locks in both sides ø to ø0, head end look only Contents Set of nos. above,,, and grease pack Order seal kit in accordance with the bore size. The seal kit includes a grease pack ( g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-0 ( g) When disassembling cylinders with bore sizes of ø through ø, grip the double flat part of either the head cover or the rod cover with a vise and loosen the other side with a wrench or an adjustable angle wrench, etc., and then remove the cover. When re-tightening, tighten approximately degrees more than the original position. (Cylinders with ø or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. Please contact SMC when disassembly is required.)

4 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Construction: With ir Cushion With air cushion Head end lock Component Parts No Description Rod cover Head cover Tube cover Cylinder tube Piston Piston rod ushing Lock piston Lock bushing Lock spring umper Hexagon socket head cap screw Cap Cap Rubber cap M/O knob M/O bolt M/O spring Stopper ring Manual release (Non-lock type): Suffix N Rod end lock Material luminum alloy luminum alloy luminum alloy luminum alloy luminum alloy Carbon steel earing alloy Carbon steel Copper alloy Stainless steel Urethane lloy steel luminum die-casted Carbon steel Synthetic rubber Zinc die-casted lloy steel Steel wire Carbon steel Series ore size Kit no. -PS -PS ir cushion -PS type -PS 3 Note Clear hard anodized Clear hard anodized Clear hard anodized Hard anodized Chromated Hard chrome plated Hard chrome plated, Heat treated lack zinc chromated lack painted Oxide film treated lack painted lack zinc chromated, Red painted Zinc chromated Zinc chromated Note) In the case of cylinders with auto switches, magnets are installed in the piston. The material is stainless steel on auto switch equipped styles ø and ø. Replacement Parts/Seal Kit (With lock at single end) 3 Contents Set of nos. above,,,,, and grease pack Order seal kit in accordance with the bore size. The seal kit includes a grease pack ( g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-0 ( g) No Description Piston gasket Wear ring Rod end nut Rod seal Piston seal Cylinder tube gasket Lock piston seal Piston holder Cushion ring Cushion ring Seal retainer Cushion valve Valve retainer Lock nut Cushion seal Cushion seal Cushion ring gasket Cushion ring gasket Valve seal Valve retaining gasket Series ore size Kit no. ir cushion type End Lock Cylinder Series Material NR Resin Rolled steel NR NR NR NR Urethane luminum alloy luminum alloy Rolled steel Rolled steel Rolled steel Rolled steel Urethane Urethane NR NR NR NR Replacement Parts/Seal Kit (With lock at double end) -PS-W -PS-W -PS-W -PS-W Long stroke Note Zinc chromated 1 pc. when using tube cover pcs. for with locks in both sides ø to ø0 only nodized nodized Only when using nickel plated, tube cover Electroless nickel plated Electroless nickel plated Nickel plated ø or larger: The same as ø or larger: The same as Contents Set of nos. above,,,,, and grease pack Order seal kit in accordance with the bore size. The seal kit includes a grease pack ( g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-0 ( g) When disassembling cylinders with bore sizes of ø through ø, grip the double flat part of either the head cover or the rod cover with a vise and loosen the other side with a wrench or an adjustable angle wrench, etc., and then remove the cover. When re-tightening, tighten approximately degrees more than the original position. (Cylinders with ø or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. Please contact SMC when disassembly is required.) CJ1 CJP CJ CJ CM CM CM3 CG3 M M M1 C C CS1 CS D- -X Technical data

5 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Series Rubber umper Type: N Head end lock: N ore size Stroke H øe MM H Width G x RcP G x TC across flats 1 ore size 0 ore size 0 ød L K F T x TC DL H S + Stroke + Stroke Manual release (Non-lock type): Suffix N HR C 0.1 WL ørf Stroke range Up to 3 Up to 0 Up to Up to 0 Up to Up to Up to Up to 10 K.. K K C 0.1 N L MM M x 1. M x 1. M x 1. M x 1. M x 1. M x 1. M x 1. M x C. 3 0 MO 3 3 x J D 1 N øi DL P 1/ 9 1/. 1/ 1/ 1/ 9 1/ 3/ 0 1/ Manual release (Lock type): Suffix L HN E 1 RF 1 1 WL ømo F 3 3 S G T G H 1 1 TC H1 13 M x 0. M x 0. M x 1.0 M x 1. M1 x 1. M x 1. F HR øe TD 1 HN (Max.) øtd TE TG TF N T cross section TE I TF J M x 0. depth M x 0. depth. M x 0. depth M x 1 depth 1 M x 1. depth M x 1. depth M x 1. depth M1 x 1. depth TG..... WL 13 13

6 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Rubber umper Type: N Rod end lock: N ore size Stroke R JW DL1 JH øij øe S + Stroke + Stroke Double end lock: N ore size Stroke W S + Stroke + Stroke l f h + l + l + Stroke ø to ø ore size 0 e f G h T 0 IJ JH (Reference) ore size 0 DL S G (1) (1) (1) (13) 1 () 1 () () () S () () 1 (9) (9) () () (13) (13) ( ): Denotes the dimensions for long stroke. JW (Reference) ore size 0 øij øe ( ): Denotes the dimensions for long strokes. The minimum stroke with rod boot is mm. End Lock Cylinder Series l 1 / stroke Head end lock (-H ) l f h + l + l + Stroke ø, ø0 Rod end lock (-R ) 13 () () (3) 9 () () () (1) (1) T () (1) 1 (13) 1 (13) (1) 1 (1) 13 (131) 139 () (1) (1) (1) (1) Double end lock (-W ) CJ1 CJP CJ CJ CM CM CM3 CG3 M M M1 C C CS1 CS D- -X Technical data

7 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Series ir Cushion Type: Head end lock: ore size Stroke H Rod end lock: ore size Stroke R Head End Lock: -H ore size 0 ore size P M x 0. M x 0. Rc 1/ Rc 1/ Rc 1/ Rc 1/ Rc 3/ Rc 1/ P M x 0. M x 0. Rc 1/ Rc 1/ Rc 1/ Rc 1/ Rc 3/ W W W Max.WH W WH For dimensions other than listed above, refer to the dimensions with rubber bumper. Rod End Lock: -R 0 Rc 1/ 1 ( ): Denotes the dimensions for long strokes. For dimensions other than the listed above, refer to the dimensions with rubber bumper. W () () () () 1 () 1 () WH W W W W x P

8 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - With Mounting racket xial foot style: L Foot Style S + Stroke + Stroke Head end lock: -H ore size LS l 9. + l 9. + l 9 + l. + l. + l. + l 3 + l ( ): Denotes the dimensions for long stroke. Rod side trunnion style: U (Rod end lock-h only) Head side trunnion style: T (Rod end lock -R only) Z + Stroke + Stroke (For dimensions other than listed below, refer to pages to, 313 to 31.) Rod side flange style: F Head side flange style: G + Stroke Rod end lock: -R LS () () () 0 (9) (9) (9) (90) (90) () 1. (13.) 1. (1.) (3) 9. (1.) 9. (1.). (.) () 1 (9) + l. (.) + l 9. (.) + l (13) + l 9. (1.) + l 9. (1.) + l 13. (.) + l 1 (31) + l Rod Side Flange Style Overall length is the same as basic style. Head Side Flange Style Head end lock: -H Rod end lock: -R ore size (Head side flange) l + l + l 1 + l + l + l + l + l 13 1 () 11 (3) 11 (3) 9 (3) 1 () 3 + l 1 + l + l (1) + l 1 (3) + l 1 (3) + l () + l 1 () + l ( ): Denotes the dimensions for long stroke. End Lock Cylinder Series LS 9 9 Double end lock: -W l l l 1 + l.. + l.. + l.. + l 39 + l Double end lock: -W + l 3 + l + l 1 + l + l + l + l 3 + l Rod Side Trunnion Style Overall length is the same as basic style. Head Side Trunnion Style Rod end lock: -R ore size Z (Head side trunnion) (Head side trunnion) (13) (9) (9) + l l 1 + l () + l (19) + l (19) + l () (1) (1) 13 + l + l + l 9 () + l () + l () + l ( ): Denotes the dimensions for long stroke. 9 CJ1 CJP CJ CJ CM CM CM3 CG3 M M M1 C C CS1 CS D- -X Technical data

9 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Series With Mounting racket Clevis style: D ø to ø Clevis Style ore size 0 Z + Stroke + Stroke Head end lock: -H Z l l l l l 1 + l + l + l 0 + l + l + l l 3 + l + l 3 + l + l Double end lock: -W ore size Z l 1 + l 10 + l l l + l l 1 + l + l + l + l l 1 + l l l 91 + l ( ): Denotes the dimensions for long stroke. Clevis style: D ø to ø0 Z + Stroke + Stroke Rod end lock: -R Z () () 0 () () 3 () 9 + l + l 3 + l 19 () + l (1) + l () + l 39 (3) + l (1) + l () (1) 1 () () 0 () 0 + l 11 + l 1 + l () + l (3) + l () + l () + l 9 (3) + l

10 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Use the Recommended Pneumatic Circuit Series Specific Product Precautions 1 e sure to read before handling. Refer to front matter for Safety Instructions and pages 3 to 1 for ctuator and uto Switch Precautions. This is necessary for proper operation and release of the lock. W W Head end lock Operating Precautions Rod end lock 1. Do not use 3 position solenoid valves. void use in combination with 3 position solenoid valves (especially closed center metal seal types). If pressure is trapped in the port on the lock mechanism side, the cylinder cannot be locked. Furthermore, even after being locked, the lock may be released after some time, due to air leaking from the solenoid valve and entering the cylinder.. ack pressure is required when releasing the lock. e sure air is supplied to side of cylinder without the locking mechanism, as above, prior to supplying air pressure to the side with end lock or lock may not be released. ( Refer to Releasing the Lock.) 3. Release the lock when mounting or adjusting the cylinder. If mounting or other work is performed when the cylinder is locked, the lock unit may be damaged.. Operate with a load ratio of % or less. If the load ratio exceeds %, this may cause problems such as failure of the lock to release, or damage to the lock unit.. Do not operate multiple cylinders in synchronization. void applications in which two or more end lock cylinders are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required.. Use a speed controller with meter-out control. Lock cannot be released occasionally by meter-in control.. e sure to operate completely to the cylinder stroke end on the side with the lock. If the cylinder piston does not reach the end of the stroke, locking and unlocking may not be possible.. Do not use an air cylinder as an air-hydro cylinder. This could result in leakage of oil. 9. Install a rod boot without twisting. If the cylinder is installed with its bellows twisted, it could damage the bellows.. djust an auto switch position so that it operates for movement to both the stroke end and backlash ( mm) positions. When a -color indication switch is adjusted for green indication at the stroke end, it may change to red for the backlash return, but this is not abnormal. Operating Precautions Warning 1. Do not operate the cushion valve in the fully closed or fully opened state. Using it in the fully closed state will cause the cushion seal to be damaged. Using it in the fully opened state will cause the piston rod assembly or the cover to be damaged.. Operate within the specified cylinder speed. Otherwise, cylinder and seal damage may occur. Operating Pressure 1. Use pressures over 0. MPa at port with locking mechanism. This is required to release the lock. Exhaust Speed 1. Locking will occur automatically if the pressure applied to the port on the lock mechanism side falls to 0.0 MPa or less. In cases where the piping on the lock mechanism side is long and thin, or the speed controller is separated at some distance from the cylinder port, the exhaust speed will be reduced. Take note that some time may be required for the lock to engage. In addition, clogging of a silencer mounted on the solenoid valve exhaust port can produce the same effect. Warning Relation to Cushion 1. When cushion valve at side with locking mechanism is fully opened or closed, piston rod may reached at stroke end. Thus lock is not established. nd when locking is done at cushion valve fully closed, adjust cushion valve since lock may not be released. Releasing the Lock 1. efore releasing the lock, be sure to supply air to the side without the lock mechanism, so that there is no load applied to the lock mechanism when it is released. (Refer to the recommended pneumatic circuits.) If the lock is released when the port on the other side is in an exhaust state, and with a load applied to the lock unit, the lock unit may be subjected to an excessive force and be damaged. Furthermore, sudden movement of the piston rod is very dangerous. Disassembly/Replacement 1. Do not replace the bushings or the cushion seals. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly.. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3. Those with a bore of ø or more cannot be disassembled. When disassembling cylinders with bore sizes of ø through ø, grip the double flat part of either the head cover or the rod cover with a vise and loosen the other side with a wrench or an adjustable angle wrench, etc., and then remove the cover. When re-tightening, tighten approximately degrees more than the original position. (Cylinders with ø or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. Please contact SMC when disassembly is required.) 31 CJ1 CJP CJ CJ CM CM CM3 CG3 M M M1 C C CS1 CS D- -X Technical data

11 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Manual Release 1. Manual release non-lock type Insert the accessory bolt from the top of the rubber cap (it is not necessary to remove the rubber cap), and after screwing it into the lock piston, pull it to release the lock. If you stop pulling the bolt, the lock will return to an operational state. Thread sizes, pulling forces and strokes are as shown below. ore size,,,,, 0 Thread size M. x 0. x L or more M3 x 0. x L or more M x 0. x L or more Pulling force.9n N.N Remove the bolt for normal operation. It can cause lock malfunction or faulty release. Lock Stroke 3 3. Manual release lock type While pushing the M/O knob, turn it 90 counterclockwise. The lock is released (and remains in a released state) by aligning the mark on the cap with the OFF mark on the M/O knob. When locking is desired, turn the M/O knob 90 clockwise while pushing completely down, and align the mark on the cap with the ON mark on the M/O knob. The correct position is confirmed by a clicking sound. Failure to click it into place properly can cause the lock to disengage. 3 Locked state Series Specific Product Precautions e sure to read before handling. Refer to front matter for Safety Instructions and pages 3 to 1 for ctuator and uto Switch Precautions. Release Rubber cap Unlocked state Locked state Working Principle The figures below are the same as those for Series C. Head end lock (Rod end lock is the same.) 1. When the piston rod is getting closer to the stroke end, the taper part ( ) of the piston rod edge will push the lock piston up. Pressure. The lock piston is pushed up further. 3. The lock piston is pushed up into the groove of the piston rod to lock it. (The lock piston is pushed up by spring force.) t this time, it is exhausted from the port on the head side and introduced into the atmosphere.. When pressure is supplied in the head side, lock piston will be pushed up to release the lock. Exhaust ack pressure. When the lock is released, the cylinder will move forward. Exhaust Piston rod Unlocked state Spring Lock piston Pressure

12 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - uto Switch Mounting Position (Detection at stroke end) and Its Mounting Height Reed auto switch D-9 ø to ø HS D-9 V ø to ø D-C, C ø to ø uto Switch Mounting Position / Except Single cting/direct Mount Type (R, KR), End Lock Cylinder () uto switch model ore size 0 D-9 D-9 V 9 9 Series uto Switch Mounting 1 HS () () 1 (9) 3 () () (). () ( ): Dimension of the D-9. and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. Hs D-C3C, CC ø to ø Hs D-M9 D-M9 V D-M9 W D-M9 D-M9 V D-M9 WV 3 39 D-C/C D-C3C D-CC () () () (3) () () (.). (.) 1. (9.) 3. (.). (.). (.) and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. D-,, 9W ø to ø0 Hs.. 1. D- D (.). (.). (3.) 1. (.). (3.). (3.). (.). (.) D-9W (.) 1. (.). (.). (9.). (3.). (3.). (.). (.) D-H D-HC D-H W D-H D-HNF (.). (.). (.). (31.). (). () D-G W D-K9W D-G9F D-G D-K D-GNT D-G () () 1 () 31 () 3 (3) 3 (3) () () Note 1) Figures in parentheses are for the long stroke, double rod type. Note ) In the actual setting, adjust them after confirming the auto switch operating condition. 3. uto switch uto switch uto switch Solid state auto switch D-M9 /D-M9 W/D-M9 ø to ø HS Operating Range uto switch model ore size 0 () ( ): Dimension of the D-M9. and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. D-M9 V, M9 WV/D-M9 V ø to ø HS () ( ): Dimension of the D-M9 V. and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. D-G, K, G W, G/D-K9W, D-G9F, D-GNT ø to ø0 uto switch Hs 1 D-H, H W/D-HNF, H ø to ø Hs D-HC ø to ø Hs.. 9. uto switch 3. uto switch D-C/C D-H D-/ D-M9 V D-H W D-HNF D-9W D-M9 WV D-C3C D-H D-G/K D-M9 V D-9 D-CC D-M9 D-G W D-9 V D-M9 W D-K9W D-M9 Hs Hs Hs Hs D-GNT D-G9F D-HC D-G 3 CJ1 CJP CJ CJ CM CM CM3 CG3 M M M1 C C CS1 CS D- -X Technical data

13 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Series uto Switch Mounting Proper uto Switch Mounting Position (Detection at stroke end) Single cting, Spring Return Type (S)/Spring Extend Type (T) Proper uto Switch Mounting Position: Single cting/spring Return Type (S) uto switch model ore size Dimensions Up to st to st 1 to st to 0 st 1 to 1 st 1 to 1 st 1 to 0 st 9 9 D-9 (V) D-M9 (V) D-M9 W (V) D-M9 (V) D-C D-C D-C3C D-CC D-H W D-H D-HC D-H D-HNF D D D-GNT D-G9F D-9W Note) In the actual setting, adjust them after confirming the auto switch operating condition. Proper uto Switch Mounting Position: Single cting/spring Extend Type (T) uto switch model ore size Dimensions Up to st to st 1 to st to 0 st 1 to 1 st 1 to 1 st 1 to 0 st D-9 (V) D-M9 (V) D-M9 W (V) D-M9 (V) D-C D-C D-C3C D-CC D-H W D-H D-HC D-H D-HN D- D- D-GNT D-G9F D-9W Note) In the actual setting, adjust them after confirming the auto switch operating condition. 3

14 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Proper uto Switch Mounting Position (Detection at stroke end) Proper uto Switch Mounting Position: Direct Mount Type (R, KR) uto switch model ore size D-M9 D-M9 V D-M9 W D-M9 WV D-M9 D-M9 V D-C D-C D-C3C D-CC D- D- Note) In the actual setting, adjust them after confirming the auto switch operating condition. D-C D-C D-C3C D-CC Proper uto Switch Mounting Position: End Lock Cylinder () uto switch model ore size 0 D-9 D-9 V Locking position Head side Rod side Double sides Head side Rod side Double sides Head side Rod side Double sides Head side Rod side Double sides Head side Rod side Double sides Head side Rod side Double sides Head side Rod side Double sides Head side Rod side Double sides D-9 D-9 V 9 9 () () 31 1 (9) () 3 () () D-M9 D-M9 V D-M9 W D-M9 WV D-M9 D-M9 V () 3 3 () 3 () (3) 9 () 9 9 () (.)... (.) (9.) (.) 3... (.)... (.) D- D- Note 1) Figures in parentheses are for the long stroke type. Note ) In the actual setting, adjust them after confirming the auto switch operating condition. uto Switch Mounting Series.. (.)... (.)... (3.) (.) 31.. (3.). (3.).. (.)... (.) D-9W D-9W (.) (.) 9... (.). 3.. (9.) 3... (3.)... (3.)... (.)... (.). D-H W D-HNF D-H D-H D-HC D-H D-HC D-H W D-H D-HNF (.) (.) (.). 3.. (31.) 3... ()... (). D-G9F D-GNT 1 D-G W D-K9W D-G9F D-G D-K D-GNT D-G 3 () 3 3 () () 3 31 () 3 (3) 3 (3) () () 3 CJ1 CJP CJ CJ CM CM CM3 CG3 M M M1 C C CS1 CS D- -X Technical data

15 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Minimum uto Switch Mounting Stroke uto switch model D-M9 D-M9 W D-M9 D-M9 V D-9 V D-M9 WV D-M9 V D-C D-C D-H D-H W D-H D-HNF D-C3C D-CC D- D- D-G D-K9 D-9W Note 1) uto switch mounting uto switch model D-M9 D-M9 W D-M9 D Different surfaces Note 1) Note 1) No. of auto switch mounted Same surface Note 1) Note 1) Note 1) 0 Different surfaces (n ) + (n =,, ) Note 3) (n ) + (n =,, ) Note 3) (n ) + (n =,, ) Note 3) (n ) + (n =,, ) Note 3) (n ) + (n =,, ) Note 3) (n ) + (n =,, ) Note 3) (n ) + (n =,, ) Note 3) (n ) + (n =,, ) Note 3) (n ) + (n =,, ) Note 3) (n ) + (n =,, ) Note 3) n n: No. of auto switch Same surface (n ) + + (n ) (n =,, (n =, 3,, ) ) Note 3) Note 3) When n is an odd number, an even number that is one larger than this odd number is used for the calculation. Different surfaces Less than stroke Note ) Less than stroke Note ) With auto switches Note ) Minimum stroke for mounting auto switches in the other mounting styles mentioned in Note 1. 3 Series uto Switch Mounting 3 Correct auto switch mounting position is 3. mm from the back face of the switch holder. Same surface The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. Less than stroke Note ) Less than 0 stroke Note ) Less than stroke Note ) + (n ) (n =, 3,, ) + (n ) (n =, 3,, ) 0 + (n ) (n =, 3,, ) + (n ) (n =, 3,, ) + (n ) (n =, 3,, ) + (n ) (n =, 3,, ) + (n ) (n =, 3,, ) 0 + (n ) (n =, 3,, ) + (n ) (n =, 3,, ) + (n ) (n =, 3,, )

16 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Operating Range uto switch model uto Switch Mounting racket: Part No. uto switch model D-M9 (V) D-M9 W (V) D-9 (V) D-M9 (V) D-C /C D-C3C/CC D-H D-H W D-HNF D-HL D- / D-9W D-G /K9 D-G W/K9W D-G/G9F D-GNT D-GN ø Note 1) M3-0 Note ) M3-0S M-0 M-0S ø Note 1) M3-0 Note ) M3-0S M-0 ore size ore size ø ø [Stainless Steel Mounting Screw Kit] The following stainless steel mounting screw kit is available. Use it in accordance with the operating environment. (Since the auto switch mounting bracket is not included, order it separately.) 3: For D-//G/K types Note 3) Refer to pages and for details on the 3. The above stainless steel screws are used when a cylinder is shipped with the G auto switch. When only an auto switch is shipped independently, the 3 is attached. 9 D-9 (V) D-M9 (V) D-M9 W (V) D-M9 (V) D-C/C D-C3C/CC D- / D-9W D-H /H W D-HNF/H D-HC D-G /G W/G9F D-G/K9/K9W D-GNT D-GN... Since this is a guideline including hysteresis, not meant to be guaranteed. (ssuming approximately ±% dispersion.) There may be the case it will vary substantially depending on an ambient environment. ø Note 1) M3-0 Note ) M3-0S M Note 1) M3-0 Note ) M3-0S M-0-0 Note 1) M3-0 Note ) M3-0S M-0-0 a Switch bracket b Switch holder ø Note 1) M3-0 Note ) M3-0S M-0 M-0S M-0S M-0S M-0S M-0S Note 1) Set part number which includes the auto switch mounting band (M- ) and the holder kit (J-1/Switch bracket: Transparent). Note ) Set part number which includes the auto switch mounting band (M- S/Stainless steel screw) and the holder kit (J-1/Switch bracket: White). Note 3) For the D-M9 (V) type auto switch, do not install the switch bracket on the indicator light. (1) M- (S) is a set of "c" and "d" in the figure. () J -1 is a set of "a" and "b" in the figure. J-1 (Switch bracket: White) J-1 (Switch bracket: Transparent) 0 uto Switch Mounting Series -0 c uto switch mounting band ø -0 uto switch ø0 - d uto switch mounting screw 3 CJ1 CJP CJ CJ CM CM CM3 CG3 M M M1 C C CS1 CS D- -X Technical data

17 Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - Cylinder racket, by Stroke/uto Switch Mounting Surfaces uto switch model Switch type D-9 (V) D-M9 (V) D-M9 W (V) D-M9 (V) Switch mounting surface D-C/C D-H /H W D-H/HNF D-C3C/CC/HC D-//G/K D-G W/K9W/G D-G9F/GNT D-9W st or more to st Trunnion style is not available for bore sizes ø and ø0. 3 Type Model Electrical entry Features Reed auto switch D-H1, H, H D-HNW, HPW, HW D-H D-GNT Grommet (In-line) Diagnostic indication (-color indication) Water resistant (-color indication) With timer Solid state auto switch Series uto Switch Mounting D-3 D-C3, C D-C asic style, Foot style, Flange style, Clevis style 1 (Rod cover side) st or more st or more st or more st or more (Different surfaces) to 9 st to 9 st to st to st Grommet (In-line) (Same surface) Port surface Port surface Port surface st or more 0 st or more st or more st or more st or more Without indicator light 1 (Rod cover side) st or more st or more st or more st or more st or more Trunnion style (Different surfaces) to 9 st to 9 st to st to st to st pplicable bore size ø to ø ø to ø0 ø to ø st: Stroke (Same surface) st or more to st st or more st or more to st st or more Other than the applicable auto switches listed in How to Order, the following auto switches can be mounted. For detailed specifications, refer to pages 9 to 3. For solid state auto switches, auto switches with a pre-wired connector are also available. Refer to pages and for details. Normally closed (NC = b contact) solid state auto switches (D-F9G/F9H types) are also available. Refer to page for details Wide range detection type, solid state switches (D-GN type) are also available. Refer to page for details. st or more 0 st or more st or more st or more st or more