Air Cylinder. ø6, ø10, ø16. Easy installation. Reduced piston rod deflection

Transcription

1 ir Cylinder Series CJ2 ø, ø, ø CJ1 CJP Improved wear resistance The bearing portions of the rod cover and the clevis have been improved in wear resistance to ensure the longevity of the cylinder. Series Variations Standard Series CJ2 Series Reduced piston rod deflection The clearance between the bushing and the piston rod has been decreased to achieve higher accuracy, thus decreasing the deflection of the piston rod. ction Double acting Single acting Rod Single rod Double rod Single rod, Spring return/ Spring extend asic Easy installation The installation is simple because a tool can be placed directly over the cover for installation. uilt-in magnet Standard variations With air Clean Copper and cushion series fluorine-free High speed actuation possible Either the rubber bumper or the air cushion can be selected according to the drive speed conditions. Therefore, it can support high speed drives. Rubber bumper to mm/s (Standard equipment) ir cushion to mm/s Page 2 2 CJ2 CM2 CG1 M M1 C2 CS1 CS2 Non-rotating Rod Series CJ2K Double acting Single acting Single rod Single rod, (Spring return/ Spring extend) 3 uilt-in Speed Controller Series CJ2Z Double acting Single rod Double rod Low Friction Series CJ2Q Double acting Single rod 9 Direct Mount Series CJ2R Double acting Single acting Single rod Single rod, (Spring return/ Spring extend) 9 9 Direct Mount, Non-Rotating Rod Series CJ2RK Double acting Single acting Single rod Single rod, (Spring return/ Spring extend) 2 End lock cylinder Series CJ2 Double acting Single rod 1 D- Low-speed cylinder Series CJ2X Refer to est Pneumatics No Technical data

2 Combinations of Standard Products and Made Series CJ2 : Standard : Made to Order specifications : Special product (Contact SMC for details.) : Not available Symbol Specification Series ction/type pplicable bore size Double acting Single rod Double rod CJ2 (Standard) Single acting Single rod Single rod (spring return) (spring extend) ø to Double acting Single rod CJ2K (Non-rotating) Single acting Single rod Single rod (spring return) (spring extend) ø, ø Standard Standard D uilt-in magnet ø to ø CJ2- ir cushion ø, ø -, 11- Clean series () (3) 2- Copper and Fluorine-free () ø to ø X Heat-resistant cylinder ( to C) ()() X Cold-resistant cylinder ()() X9 Low-speed cylinder ( to mm/s) () ø to ø X13 Low-speed cylinder ( to mm/s) () XC3 Special port position ()() XC djustable stroke cylinder/djustable retraction type ()() XC9 djustable stroke cylinder/djustable extension type ()() ø, ø XC Dual stroke cylinder/double rod type () XC11 Dual stroke cylinder/single rod type () XC22 Fluororubber seal () XC1 With hose nipple ø to ø X339 Same as CJ1 mounting dimensions ø, ø (1) (2) (2) X3 Short mounting pitch ø Note 1) ø foot style only. Note 2) ø and ø double clevis style. Note 3) ø and ø only. Note ) Mounting style: Not compatible with the clevis style. switch is available in the band mounting style only. Note ) switch is available in the band mounting style only. Note ) Not compatible with cylinders with a switch. Note ) Not compatible with cylinders with a air cushion. Note ) vailable only for locking at head end. Note 9) Refer to est Pneumatics No. 3 for low-speed cylinders. Note ) vailable only for locking on rod side.

3 to Order Specifications Series CJ2 CJ2Z (uilt-in speed controller) Double acting Single rod Double rod CJ2Q (Low friction) Single rod Single rod CJ2R (Direct mount) CJ2RK (Direct mount, Non-rotating) Single rod Single rod Single rod Single rod Single rod (spring return) (spring extend) (spring return) (spring extend) CJ2 (With end lock) Double acting Double acting Single acting Double acting Single acting Double acting Double acting Single rod ø, ø ø () CJ2X Low-speed cylinder (9) Single rod ø, ø CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 () () D- 1 Technical data

4 ir Cylinder: Standard Type Double cting, Single Rod Series CJ2 ø, ø, ø L F D With auto switch and mounting style Mounting style asic style xial foot style Rod side flange style Double clevis style (Except ø) CJ2 L CDJ2 L mm mm mm Cylinder standard stroke Refer to the standard stroke table on page 3. Cushion Nil Rubber bumper ir cushion (Except ø) With auto switch (uilt-in magnet) Head cover port location Symbol ø ø, ø Nil Perpendicular to axis R xial xial M9W pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Grommet 3-wire (NPN) 3-wire (PNP) No 2-wire V 2V Yes Connector No Diagnostic indication (2-color indication) Grommet Yes Lead wire length symbols:. m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL m Z (Example) M9NWZ None N (Example) HCN DC V, V 2-wire V Connector Yes 2V 3-wire (NPN) V, V 3-wire (PNP) Grommet V V, V V C 2 V V V or less 2 V or less Perpendicular FNV FPV FV J9C FNWV FWV FV 2 3 3C C 9W Rail mounting style Example and mounting style For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. In-line F9 FP J9 F9W FPW J9W F F9F H 2H 3H H CDJ2-- CDJ2-- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. Made to Order Refer to page 3 for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. D-9W cannot be mounted on bore size ø cylinder with air cushion. Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. 2 Diagnostic indication (2-color indication) Indicator light Wiring (Output) 2-wire Water resistant (2-color indication) With diagnostic output (2-color indication) -wire (NPN) 3-wire (NPN equivalent) Grommet Yes How to Order For configuration, refer to page 3. Double clevis is only available for being perpendicular to axis. Load voltage model Rail mounting (ø, ø) and mounting (ø, ø, ø) M9N M9P M9 HC M9NW M9PW M9W H HNF C3C CC uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Lead wire length (m). 1 3 None (Nil) (M) (L) (Z) (N) Pre-wired pplicable load connector Relay, PLC Relay, PLC

5 ir Cylinder: Standard Type Double cting, Single Rod Series CJ2 Specifications ction Fluid Double acting, Single rod ir Proof pressure Maximum operating pressure 1 MPa. MPa Minimum operating pressure Rubber bumper. MPa. MPa ir cushion.1 MPa mbient and fluid temperature Cushion Lubrication Without auto switch: C to C, With auto switch: C to C Rubber bumper/ir cushion Not required (Non-lube) length tolerance Piston speed llowable kinetic energy No freezing Rubber bumper ir cushion Rubber bumper ir cushion (Effective cushion length).j +1. to mm/s to mm/s.3j.9j.j (9. mm).1j (9. mm) CJ1 CJP CJ2 CM2 CG1 M M1 JIS Symbol Double acting, Single rod Standard Standard stroke, 3,,, 3,,,,,, C2 CS1 CS2, 3,,,,,,, 1, 2 Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Head Cover Port Location Either perpendicular to the cylinder axis or in-line with the cylinder axis is available for basic style. (ø is available only as in-line style.) Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. xial Perpendicular Made to Order Specifications (For details, refer to pages 133 to 19.) Symbol Specifications X X X X9 Change of rod end shape Heat resistant cylinder ( C) Not available with switch & with air cushion Cold resistant cylinder Not available with switch & with air cushion Low speed cylinder ( to mm/s) Not available with air cushion X13 Low speed cylinder ( to mm/s) Not available with air cushion XC3 Special port location Not available with air cushion XC XC9 djustable stroke cylinder/djustable extension type djustable stroke cylinder/djustable retraction type XC Dual stroke cylinder/double rod type XC11 Dual stroke cylinder/single rod type XC22 Fluororubber seals Not available with air cushion XC1 With hose nipple 3 D- Technical data

6 Series CJ2 Mounting Style and ccessory/for details, refer to page 1. Standard equipment Option Mounting Pin and snap ring are shipped together with double clevis and double knuckle joint. Mounting racket Part No. Mounting bracket Foot bracket Flange bracket T-bracket Mounting nut Clevis pin Single knuckle joint Double knuckle joint T-bracket CJ-L CJ-F T-bracket is used with double clevis (D). asic style CJ-L CJ-F CJ-T xial foot style CJ-L CJ-F CJ-T Rod side flange style Double clevis style Mass asic mass dditional mass per each mm of stroke Mounting bracket mass ccessory bracket xial foot style Rod side flange style Double clevis style (With pin) Single knuckle joint Double knuckle joint (With pin) T-bracket (g) Mounting nut and rod end nut are included in the basic mass. Mounting nut is not attached to the double clevis style, so the mounting nut mass is already subtracted. Calculation: (Example) CJ2L- asic mass 2 (ø) dditional mass / stroke Cylinder stroke stroke Mounting bracket mass (xial foot style) 2 + / x + = g Precautions e sure to read before handling. Refer to front matters and for Safety Instructions and pages 3 to 11 for ctuator and uto Switch Precautions. Mounting Caution 1. During installation, secure the rod cover and tighten by applying an appropriate tightening force to the retaining but or to the rod cover body. If the head cover is secured or the head cover is tightened, the cover could rotate, leading to the deviation. 2. Tighten the retaining screws to an appropriate tightening torque within the range given below. ø: 2.1 to 2. N m, ø:.9 to. N m, ø:. to 11. N m 3. To remove and install the retaining ring for the knuckle pin or the clevis pin, use an appropriate pair of pliers (tool for installing a type C retaining ring). In particular, use a pair of ultra-mini pliers for removing and installing the retaining ring on the ø cylinder.. In the case of auto switch rail mounting style, do not remove the rail that is mounted. ecause retaining screws extend into the cylinder, this could lead to an air leak.. Please contact SMC when the stroke exceeds mm for the axial foot mounting style.

7 ir Cylinder: Standard Type Double cting, Single Rod Series CJ2 Clean Series Copper and Fluorine-free Cylinder (For CRT manufacturing process) -CJ2 Mounting style Head cover port location 2-CJ2 Mounting style Head cover port location Clean Series ir cylinder which is applicable for the system which discharges leakage from the rod section directly into the outside of clean room by relief port and making an actuator s rod section having a double seal construction. Specifications ction Maximum operating pressure Double acting, Single rod,,. MPa Minimum operating pressure Cushion ø ø, ø.1 MPa. MPa Rubber bumper/ir cusion Standard stroke Same as standard type. (Refer to page 3.) Mountable (and mounting style) Mounting asic style, xial foot style, Rod side flange style Copper and fluorine-free Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. Specifications ction Maximum operating pressure Minimum operating ø pressure ø, ø Cushion Standard stroke Mounting Double acting, Single rod,,. MPa. MPa. MPa Rubber bumper (Standard equipment) Same as standard type. (Refer to page 3.) Mountable (and mounting style) asic style, xial foot style, Rod side flange style, Double clevis style (Except ø) CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 Construction Construction For details, refer to the separate catalog Pneumatic Clean Series. Low-speed Cylinder CJ2 X Mounting style Low-speed Cylinder Smooth operation with a little sticking and slipping at low speed. Can start smoothly with a little ejection even after being rendered for hours. Specifications ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure Double acting, Single rod, ir 1. MPa. MPa. MPa mbient and fluid temperature Cushion Lubrication length tolerance Piston speed ø llowable kinetic energy ø Refer to est Pneumatics No. 3. Without auto switch: to C (No freezing) With auto switch: to C Rubber bumper (Standard equipment) Not required (Non-lube) to 3 mm/s.3 J.9 J D- Technical data

8 Series CJ2 Construction (Not able to disassemble) CJ2-R Piston Magnet Piston construction when auto switch is mounted. CJ2, CJ2 Piston Magnet Piston construction when auto switch is mounted. With air cushion Component Parts Dedicated for with ir Cushion Type No. Description 1 Rod cover 2 Head cover 3 Cylinder tube Piston rod Piston Mounting nut umper 9 Seal retainer Piston seal 11 Rod seal Tube gasket 13 Piston gasket Only for ø Material luminum alloy luminum alloy Stainless steel Stainless steel rass rass Rolled steel Urethane luminum alloy NR NR NR NR Note nodized nodized Nickel plated Nickel plated nodized No Description Cushion needle Steel balls Cushion ring Check seal Needle seal Cushion ring gasket Material Stainless steel earing steel rass NR NR NR Note

9 ir Cylinder: Standard Type Double cting, Single Rod Series CJ2 asic Style () CJ2 Head cover port location CJ2 Mounting nut.3 Piping port M x. Piping port M x..3 CJ1 CJP CJ2 CJ2,.3 Mounting nut Z + Piping port 2 x M x. Piping port M x. CM2 CG1 M M1 C2 Z + Head cover port location: xial location (R) CS1 CS2 With air cushion: CJ2 Head cover port location Mounting nut Piping port 2 x M x. Head cover port location: xial location (R) Piping port M x..3 Z + Rod End Nut Material: Iron For details of the mounting nut, refer to page C D 3 F G 1. G H MM M3 x. M x. M x. With ir Cushion/Dimensions other than the table below are the same as the table above. 1.3 C 1 2 G.. G.. N N 2 2 W W WW.. S N N Z 93 9 NDh pplicable Part no. bore NTJ- NTJ- NTJ- NN M x 1. M x 1. M x 1.. S 9 C d M3 x. M x. M x. T 3 H Z D- Technical data

10 Series CJ2 xial Foot Style (L) CJ2L Head cover port location CJ2L Mounting nut Cover surface Piping port M x. Piping port M x x ølc Mounting hole Z + Rod cover side Head cover side CJ2L, Cover surface Mounting nut Piping port 2 x M x. Piping port M x..3 Z + Head cover port location: xial location (R) With air cushion: CJ2L Head cover port location Mounting nut Head cover port location: xial location (R) Cover surface Piping port 2 x M x. Piping port M x..3 Z + Rod End Nut For details of the mounting nut, refer to page C D 3 F G 1. G H L 23 LC... LH LT LX LY.. 2 LZ MM M3 x. M x. M x. N.. N Part no. NTJ- NTJ- NTJ- NN M x 1. M x 1. M x 1. pplicable bore S 9. T 3 C X Material: Iron d M3 x. M x. M x. Y 9 H Z With ir Cushion/Dimensions other than the table below are the same as the table above. 1.3 C G G L N N W W WW S Z 93 9

11 ir Cylinder: Standard Type Double cting, Single Rod Series CJ2 Rod Side Flange Style (F) CJ2F Head cover port location CJ2F Cover surface Mounting nut Piping port M x. Piping port M x..3.3 CJ1 2 x øfc Mounting hole Z + Rod cover side Head cover side CJP CJ2 CJ2F, Cover surface Mounting nut Piping port 2 x M x. Piping port M x. CM2 CG1 M.3 M1 2 x øfc Mounting hole Z + Head cover port location: xial location (R) C2 CS1 CS2 With air cushion: CJ2F Head cover port location Cover surface Mounting nut Piping port 2 x M x. Head cover port location: xial location (R) Piping port M x..3 Z + Rod End Nut Material: Iron For details of the mounting nut, refer to page C D 3 F F FC... FT FX FY FZ G 1. With ir Cushion/Dimensions other than the table below are the same as the table above. C F G G N N W W WW S Z G H MM M3 x. M x. M x. N.. Part no. NTJ- NTJ- NTJ- N pplicable bore. NN M x 1. M x 1. M x 1. C S 9 d M3 x. M x. M x. T 3 H Z 9 D- Technical data

12 Series CJ2 Double Clevis Style (D) CJ2D Z + Piping port 2 x M x. øcdh9 +.3 Clevis pin.3 (øcdd9.) -.3 T-bracket CZ -.3 For details, refer to page 1. Clevis pin and retaining ring are shipped together. ZZ + With air cushion: CJ2D Z + Piping port 2 x M x. +.3 øcdh9 Clevis pin (øcdd9.3.) -.3 T-bracket CZ -.3 For details, refer to page 1. ZZ + Rod End Nut Clevis pin and retaining ring are shipped together. 1.3 C 1 2 CD(cd) 3.3 CX 3.2. CZ 1.3 D G G 1 23 H 2 2 MM M x. M x. N.. N Part no. NTJ- NTJ- R pplicable bore S U C Material: Iron d M x. M x. Z 2 H 3.2 ZZ T-bracket Dimensions TC.. TH 29 3 TV TW 22 2 TX 32 3 TY With ir Cushion/Dimensions other than the table below are the same as the table above. 1.3 C 1 2 CZ 1.3 G.. G N N 33 3 S W W WW.. Z 1 ZZ 1 11

13 ir Cylinder: Standard Type Double cting, Single Rod Series CJ2 ccessory racket Dimensions Single Knuckle Joint Clevis Pin Knuckle Pin CJ1 CJP pplicable Part no. 1 bore L1 MM ND H NX R1 I-J 21 M x I-J 2 M x Double Knuckle Joint Material: Rolled steel U1 9 1 Part no. CD-J CD-Z CD-J pplicable bore Dd Mounting Nut Material: Stainless steel pplicable d L l m t snap ring Type C Type C Type C 3.2 For ø double clevis style, with air cushion and builtin speed controller. Clevis pins are shipped with retaining rings. Part no. CD-J IY-J pplicable bore Dd For size ø, clevis pin is diverted. Knuckle pins are shipped with retaining rings. Rod End Nut Material: Stainless steel pplicable d L l m t snap ring Type C Type C CJ2 CM2 CG1 M M1 C2 ønd hole H xis dg CS1 CS2 Material: Rolled steel pplicable Part no. bore 1 L L1 MM Y-J Y-J M x. M x. Part no. NDd9 NDH NX R1 U1 Y-J Y-J Knuckle pin and retaining ring are shipped together. Material: rass Part no. pplicable bore C d H SNJ- SNJ- SNJ- SNKJ M x 1. M x 1. M x 1. M x 1. For ø non-rotating type. (Use SNJ- for ø non-rotating type.) Part no. NTJ- NTJ- NTJ- pplicable bore. C Material: Iron d H M3 x. 2. M x. 3.2 M x. T-bracket Rod End Cap Double clevis style cylinder x øtc Flat type/cj-cf Round type/cj-cr Material: Polyacetal Part no. pplicable bore TC CJ-T CJ-T.. TDH TH TK TN TT TU TV TW TX TY TZ T-bracket includes a T-bracket base, single knuckle joint, hexagon socket head bolt and spring washer. Part no. Flat type Round type CJ-CF CJ-CR CJ-CF CJ-CR CJ-CF CJ-CR pplicable bore D L MM M3 x. M x. M x. N R W D- 1 Technical data

14 ir Cylinder: Standard Type Double cting, Double Rod Series CJ2W ø, ø, ø How to Order With auto switch Mounting style asic style L Foot style F Flange style CJ2W L CDJ2W L With auto switch (uilt-in magnet) mm mm mm Cylinder standard stroke Refer to the standard stroke table on page 3. Cushion Nil Rubber bumper ir cushion M9W For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Rail mounting style Example CDJ2W-- and mounting style CDJ2W-- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Made to Order Refer to page 3 for details. pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Grommet 2 V DC V, V 2-wire V Connector Yes 2 V 3-wire (NPN) V, V 3-wire (PNP) Grommet Connector Indicator light No Yes No Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire Water resistant (2-color indication) With diagnostic output (2-color indication) -wire (NPN) 3-wire (NPN equivalent) Grommet Yes Diagnostic indication (2-color indication) Grommet Lead wire length symbols:. m 1 m 3 m m Nil M L Z 2-wire (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ (Example) HCN Load voltage V V, V V V model Lead wire length (m) and mounting Rail mounting. 1 3 None Pre-wired (ø, ø) pplicable load C connector (ø, ø, ø) Perpendicular In-line (Nil) (M) (L) (Z) (N) M9N FNV F9 M9P FPV FP M9 FV J9 HC J9C Relay, M9NW PLC FNWV F9W M9PW FPW M9W FWV J9W H FV F HNF F9F 9 H 2 2H 3 3H 93 Relay, 9 H PLC C3C 3C CC C 9W Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. D-9W cannot be mounted on bore size ø cylinder with air cushion. D-HNF cannot be mounted on bore size ø cylinder. 2 V V V or less 2 V or less None N Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. 2

15 ir Cylinder: Standard Type Double cting, Double Rod Series CJ2W Specifications ction Fluid Proof pressure Maximum operating pressure Double acting, Double rod ir 1 MPa. MPa JIS Symbol Double acting, Double rod Rubber bumper Minimum operating pressure ir cushion mbient and fluid temperature Cushion Lubrication length tolerance Piston speed llowable kinetic energy No freezing Standard,, Rubber bumper ir cushion Rubber bumper ir cushion (Effective cushion length).1 MPa.1 MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper/ir cushion Not required (Non-lube) +1. to mm/s to mm/s. J.3 J.9 J Standard stroke, 3,, Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.). J (9. mm).1 J (9. mm) CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 Symbol X X X XC22 XC1 Made to Order Specifications (For details, refer to pages 133 to 19.) Specifications Change of rod end shape Heat resistant cylinder ( C) Not available with switch & with air cushion Cold resistant cylinder Not available with switch & with air cushion Fluororubber seals Not available with air cushion With hose nipple Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. 3 D- Technical data

16 Series CJ2W Mounting Style and ccessory/for details, refer to page 1. Standard equipment Option Mounting asic style Foot style Flange style Mounting nut Single knuckle joint Double knuckle joint Knuckle pin and retaining ring are shipped together with double knuckle joint. Mounting racket Part No. Mounting bracket Foot bracket Flange bracket CJ-L CJ-F CJ-L CJ-F CJ-L CJ-F Mass (g) asic mass dditional mass per each mm of stroke Mounting bracket mass Foot style Flange style Mounting nut and rod end nut are included in the basic mass. Calculation: (Example) CJ2WL- asic mass 3 (ø) dditional mass / stroke Cylinder stroke stroke Mounting bracket mass (Foot style) 3 + / x + = 9 g For accessory bracket mass, refer to page. Theoretical Output Refer to Double acting cylinder in Theoretical Output 1 of Technical data 3 on page 3. In the case of the double rod style, the force at IN side will be its theoretical output. Precautions e sure to read before handling. Refer to front matters and for Safety Instructions and pages 3 to 11 for ctuator and uto Switch Precautions. Mounting Caution 1. During installation, secure the rod cover and tighten by applying an appropriate tightening force to the retaining but or to the rod cover body. If the head cover is secured or the head cover is tightened, the cover could rotate, leading to the deviation. 2. Tighten the retaining screws to an appropriate tightening torque within the range given below. ø: 2.1 to 2. N m, ø:.9 to. N m, ø:. to 11. N m 3. To remove and install the retaining ring for the knuckle pin, use an appropriate pair of pliers (tool for installing a type C retaining ring for hole). In particular, use a pair of ultramini pliers for removing and installing the retaining rings on the ø cylinder.. In the case of auto switch rail mounting style, do not remove the rail that is mounted. ecause retaining screws extend into the cylinder, this could lead to an air leak.

17 ir Cylinder: Standard Type Double cting, Double Rod Series CJ2W Clean Series -CJ2W Mounting style Specifications Clean Series ir cylinder which is applicable for the system which discharges leakage from the rod section directly into the outside of clean room by relief port and making an actuator s rod section having a double seal construction. ction Maximum operating pressure Minimum operating pressure Cushion Standard stroke Mounting Double acting, Double rod,. MPa.1 MPa Rubber bumper Same as standard type. (Refer to page 3.) Mountable (and mounting style) asic style, Foot style, Flange style CJ1 CJP CJ2 For details, refer to the separate catalog Pneumatic Clean Series. Construction (Not able to disassemble) CM2 CG1 M M1 C2 CS1 CS2 Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) 2-CJ2W Mounting style Copper and fluorine-free Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. Specifications ction Maximum operating pressure Minimum ø operating pressure ø, ø Cushion Standard stroke Mounting Double acting, Double rod,,. MPa. MPa.1 MPa Rubber bumper, 3,, Mountable (and mounting style) asic style, Foot style, Flange style D- Technical data

18 Series CJ2W Construction (Not able to disassemble) With air cushion Component Parts Dedicated for with ir Cushion Type No Description Rod cover Cylinder tube Piston rod Piston Mounting nut umper Piston seal Rod seal Tube gasket Piston gasket Material luminum alloy Stainless steel Stainless steel rass rass Rolled steel Urethane NR NR NR NR Note nodized Nickel plated Nickel plated No Description Cushion needle Steel balls Cushion ring Check seal Cushion ring gasket Needle seal Material Stainless steel earing steel rass NR NR NR Note

19 ir Cylinder: Standard Type Double cting, Double Rod Series CJ2W asic Style () CJ2W CJ2W Rod cover Mounting nut Piping port 2 x M x. -.3 CJ1 CJP Z + 2 x CJ2 Mounting nut CM2 Piping port 2 x M x. CG1 M.3 M1 Z + 2 x H + C2 CS1 CS2 With air cushion: CJ2W Mounting nut Piping port 2 x M x..3 Rod End Nut Z + 2 x For details of the mounting nut, refer to page 1. pplicable Part no. bore NTJ- NTJ- NTJ-. C Material: Iron d H M3 x. M x. M x C D F G H 1.3 C 1 2 G.. N W WW.. S Z 2 3 MM N ND h NN S T Z M3 x..1 M x M x. M x... With ir Cushion/Dimensions other than the table below are the same as the table above. 1 () 3 11 (2).22 M x 1. M x 1. 9 ( ) in S and Z dimensions: With auto switch.22 D- Technical data

20 Series CJ2W Foot Style (L) CJ2WL Mounting nut Piping port 2 x M x. Cover surface Z + 2 x Piping port 2 x M x. Mounting nut 2 x ølc Mounting hole Z + 2 x H + With air cushion: CJ2WL Mounting nut Cover surface Piping port 2 x M x. Z + 2 x Rod End Nut For details of the mounting nut, refer to page 1. pplicable Part no. bore NTJ- NTJ- NTJ-. C Material: Iron d M3 x. M x. M x. H D F G H L LC LH LT LX LY LZ MM N NN S T X Y Z M3 x. M x () (2) M x.. M x M x.. M x 1. 9 ( ) in S and Z dimensions: With auto switch With ir Cushion/Dimensions other than the table below are the same as the table above. 1.3 G.. L. 23 N W WW.. S Z 2 3

21 ir Cylinder: Standard Type Double cting, Double Rod Series CJ2W Flange Style (F) CJ2WF Mounting nut Piping port 2 x M x. CJ1 Cover surface Z + 2 x Piping port 2 x M x. CJP CJ2 CM2 CG1 M 2 x øfc Mounting hole Z + 2 x H + M1 C2 CS1 With air cushion: CJ2WF CS2 Mounting nut Cover surface Piping port 2 x M x. Z + 2 x Rod End Nut 1.3 F G.. N W For details of the mounting nut, refer to page 1. WW.. S Z 2 3 Part no. NTJ- NTJ- NTJ- pplicable bore. C Material: Iron d M3 x. M x. M x. D F F FC FT FX FY FZ G H MM N NN S T Z M3 x. M x () (2) M x.. M x M x.. M x 1. ( ) in S and Z dimensions: With auto switch With ir Cushion/Dimensions other than the table below are the same as the table above. H D- Technical data

22 ir Cylinder: Standard Type Single cting, Spring Return/Extend Series CJ2 ø, ø, ø Spring extend Spring return L F D With auto switch Mounting style asic style xial foot style Rod side flange style Double clevis style (Except ø) mm mm mm CJ2 L S CDJ2 L With auto switch (uilt-in magnet) Head cover port location Symbol Cylinder standard stroke Refer to the standard stroke table on page 1. ction S Single acting, Spring return T Single acting, Spring extend pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. ø How to Order S ø, ø Nil R xial Perpendicular to axis xial For configuration, refer to page 3. Single acting, Spring return (S), Clevis style is available only for 9 to the axis. Not applicable to single acting, spring extend (T). M9W Type Special function Load voltage model Electrical Wiring and mounting Rail mounting (ø, ø) entry (Output) DC C (ø, ø, ø) Perpendicular In-line M9N 3-wire (NPN) FNV F9 V, V M9P Grommet 3-wire (PNP) FPV FP 2-wire V M9 FV J9 Connector HC J9C Yes 2 V M9NW 3-wire (NPN) FNWV F9W V, V Diagnostic indication M9PW 3-wire (PNP) (2-color indication) Grommet FPW M9W 2-wire V FWV J9W Water resistant (2-color indication) With diagnostic output (2-color indication) -wire (NPN) V, V H HNF FV F F9F 3-wire (NPN equivalent) V 9 H Yes 2 V Grommet 2 2H 3 3H V 93 No 2-wire V V or less 9 H 2 V Yes C3C 3C Connector No 2 V or less CC C Diagnostic indication (2-color indication) Grommet Yes 9W Lead wire length symbols:. m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL m Z (Example) M9NWZ None N (Example) HCN Reed switch Solid state switch Indicator light uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Rail mounting style CDJ2-S- Example and mounting style CDJ2-S- For rail mounting style, screws and nuts for 2 pcs. switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. Lead wire length (m). 1 3 None (Nil) (M) (L) (Z) (N) Made to Order Refer to page 1 for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. Pre-wired pplicable load connector Relay, PLC Relay, PLC

23 ir Cylinder: Standard Type Single cting, Spring Return/Extend Series CJ2 Specifications ction Single acting, Spring return/single acting, Spring extend Fluid ir Proof pressure 1 MPa Maximum operating pressure. MPa Spring extend Rubber bumper Minimum operating pressure ir cushion mbient and fluid temperature Cushion.2 MPa. MPa.2 MPa. MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper/ir cushion CJ1 CJP Lubrication length tolerance Not required (Non-lube) +1. CJ2 Piston speed llowable kinetic energy No freezing to mm/s.j.3j.9j CM2 CG1 JIS Symbol Single acting, Spring return Spring return Single acting, Spring extend Standard Standard stroke, 3,,, 3,,, 3,,,,,, Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Spring Reaction Force Spring with primary mounting load (N) Spring reaction force (N) Primary Secondary Spring with secondary mounting load M M1 C2 CS1 CS2 IN OUT When the spring is set in the cylinder When the spring is contracted by applying air Made to Order Specifications (For details, refer to pages 133 to 19.) Refer to pages 11 to 3 for cylinders with auto switches. Symbol X XC22 XC1 Specifications Change of rod end shape Fluororubber seals With hose nipple Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. D- 1 Technical data

24 Series CJ2 Mass/Spring Return (S) asic mass Mounting bracket mass asic mass Mounting bracket mass stroke 3 stroke stroke stroke stroke stroke stroke stroke xial foot style Rod side flange style Double clevis style (With pin) * Mass/Spring Extend (T) stroke 3 stroke stroke stroke stroke stroke stroke stroke xial foot style Rod side flange style Double clevis style (With pin)* (g) Mounting nut and rod end nut are included in the basic mass. Mounting nut is not attached to the double clevis style, so the mounting nut mass is already subtracted. Calculation: (Example) CJ2L-S asic mass (ø- stroke) Mounting bracket mass (xial foot style) + = 2 g (g) Mounting nut and rod end nut are included in the basic mass. Mounting nut is not attached to the double clevis style, so the mounting nut mass is already subtracted. Calculation: (Example) CJ2L-T asic mass 3 (ø- stroke) Mounting bracket mass (xial foot style) 3 + = 1 g Theoretical Output Refer to the Single acting, Spring return cylinder in Theoretical Output 1 of Technical data 3 on page 3. In the case of the spring extend style, the force at OUT side will be the ending force of the spring return, and that at the IN side will be the amount of the IN side force of the double acting style cylinder from which the beginning force of the spring return has been subtracted. Specific Product Precautions e sure to read before handling. Refer to front matters and for Safety Instructions and pages 3 to 11 for ctuator and uto Switch Precautions. Mounting Caution 1. During installation, secure the rod cover and tighten by applying an appropriate tightening force to the retaining nut or to the rod cover body. If the head cover is secured or the head cover is tightened, the cover could rotate, leading to the deviation. 2. Tighten the retaining screws to an appropriate tightening torque within the range given below. ø: 2.1 to 2. N m, ø:.9 to. N m, ø:. to 11. N m 3. In the case of a single acting cylinder, do not operate it in such a way that a load would be applied during the retraction of the piston rod of the spring return style, or during the extension of the piston rod of the spring extend style. The spring that is built into the cylinder provides only enough force to retract the piton rod. Thus, if a load is applied, the piston rod will not be able to retract to the end of the stroke.. In the case of a single acting cylinder, a breather hole is provided in the cover surface. Make sure not to block this hole during installation, as this could lead to a malfunction.. To remove and install the retaining ring for the knuckle pin or the clevis pin, use an appropriate pair of pliers (tool for installing a type C retaining ring). In particular, use a pair of ultra-mini pliers for removing and installing the retaining ring on the ø cylinder.. In the case of auto switch rail mounting style, do not remove the rail that is mounted. ecause retaining screws extend into the cylinder, this could lead to an air leak. Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) Mounting racket Part No. Mounting bracket Foot bracket CJ-L CJ-L Flange bracket CJ-F CJ-F T-bracket CJ-T T-bracket is used with double clevis (D). CJ-L CJ-F CJ-T 2-CJ2 Mounting style ction Copper and fluorine-free Head cover port location Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. Mounting Style and ccessory/for details, refer to page 1. Standard equipment Option 2 Mounting Mounting nut Clevis pin Single knuckle joint Double knuckle joint T-bracket asic style xial foot style Rod side Double flange style clevis style Pin and retaining ring are shipped together with double clevis and double knuckle joint. For the attached bracket mass, refer to page. Specifications ction Maximum operating pressure Minimum operating ø pressure ø, ø Cushion Standard stroke Mounting Single acting: Spring return Single acting: Spring extend.2 MPa,,. MPa.2 MPa. MPa Rubber bumper (Standard equipment) Same as standard type. (Refer to page 1.) Mountable (and mounting style) asic style, xial foot style, Rod side flange style, Double clevis style (Except ø)

25 ir Cylinder: Standard Type Single cting, Spring Return/Extend Series CJ2 Construction (Not able to disassemble) Single acting, Spring return CJ1 CJ2 Piston/Head cover CJP CJ2 Single acting, Spring extend CM2 CG1 M M1 C2 CS1 CS2 CJ2 Piston/Rod cover Component Parts No Description Rod cover Head cover Cylinder tube Piston rod Piston Piston Return spring Spring seat Material luminum alloy luminum alloy Stainless steel Stainless steel rass rass Piano wire rass Note nodized nodized Zinc chromated No Description Seal retainer umper Mounting nut Piston seal Rod seal Tube gasket Piston gasket Material luminum alloy Urethane rass Rolled steel NR NR NR NR Note Clear anodized (ø spring extend) Nickel plated Nickel plated D- 3 Technical data

26 Series CJ2 Single cting, Spring Return: asic Style () CJ2 S Head cover port location Mounting nut Piping port M x. Piping port M x..3 Z + Head cover port location: xial location (R) For details of the mounting nut, refer to page 1. C D F G H MM N N ND h NN M3 x. 2 M x. 2 M x M x 1. M x 1. M x 1. S to to 31 to to 1 to st 3 st st st st (39.) (.) (2.) (.).. 3 to 1 to to st st st Z to st to 3 st 31 to st to st 1 to st (.) (.) (.) (9.) to 1 to to st st st 13 ( ) in S and Z dimensions: With auto switch Single cting, Spring Return: xial Foot Style (L) CJ2L S Head cover port location Cover surface Mounting nut Piping port M x. Head cover port location: xial location (R).3 2 x ølc Mounting hole Z + Rod End Nut Piping port M x. For details of the mounting nut, refer to page 1. S CDF G H L LC LH LT LX LY LZ MM N N NN X Y to to 31 to to 1 to st 3 st st st st M3 x. 3 M x 1. (39.) (.) (2.) (.) M x.. 9. M x M x.. 9. M x to 1 to to st st st pplicable Part no. bore NTJ- NTJ- NTJ-. C Z to to 31 to to 1 to st 3 st st st st (.) (.) (.) (9.) Material: Iron to 1 to to st st st 13 ( ) in S and Z dimensions: With auto switch d M3 x. M x. M x. H

27 ir Cylinder: Standard Type Single cting, Spring Return/Extend Series CJ2 Single cting, Spring Return: Rod Side Flange Style (F) CJ2F S Head cover port location Piping Cover surface Mounting nut port M x. Head cover port location: xial location (R) For details of the mounting nut, refer to page C D 3 F FFC FT FXFYFZG H MM M3 x. M x. M x. N N NN M x 1. M x 1. M x 1. Single cting, Spring Return: Double Clevis Style (D) CJ2D 2 x øfc Mounting hole S Z + Piping port M x. Z + S to st to 3 st 31 to st to st 1 to st (39.) (.) (2.) (.) øcdh9 Clevis pin (øcdd9.3.).3 to 1 to to st st st Z to st to 3 st 31 to st to st 1 to st to st 1 to st to st (.) (.) (.) (9.) ( ) in S and Z dimensions: With auto switch 13 Piping port M x. CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2.3 T-bracket CZ.3 For details, refer to page 1. ZZ + x øtc Rod End Nut Clevis pin and retaining ring are shipped together. Part no. NTJ- NTJ- NTJ- pplicable bore. C Material: Iron d M3 x. M x. M x. H to st C 1 2 to 3 st 92 9 CD (cd) 3.3 CX CZ to st D to st 1 2 ZZ G to st H 2 2 MM M x. M x. to st 2 N N R.. 1 to st to st U to st.. S to 3 st 31 to st to st 1 to st to st 1 to st to st to st to 3 st T-bracket Dimensions TC.. TH 29 3 TV TW 22 2 TX 32 3 TY Z 31 to st to st 1 to st to st 1 to st to st D- Technical data

28 Series CJ2 Single cting, Spring Extend: asic Style () CJ2 CJ2 T Mounting nut Piping port M x CJ2, H + Z + 2 x Mounting nut Piping port M x. -.3 H + Z + 2 x For details of the mounting nut, refer to page C D 3 F G H MM NN 1. 2 M3 x. M x M x. M x. M x 1.. M x N N ND h T Single cting, Spring Extend: xial Foot Style (L) 3 to st. (1.).. to 3 st. (.) 31 to st 9. (.) 9 S to st 3. (.) 1 1 to st to st to st 9 to st 11 Z to to 31 to to 1 to st 3 st st st st. (9.).. 3. (.). (92.) (.) 9 1 to 1 to st st to st ( ) in S and Z dimensions: With auto switch CJ2L T CJ2L Cover surface Mounting nut Piping port M x CJ2L, Cover surface Cover surface H + Mounting nut Z + 2 x Piping port M x. Rod cover side Head cover side.3 Rod End Nut 2 x ølc Mounting hole H + Z + 2 x For details of the mounting nut, refer to page 1. S C D F G H L LC LH LT LX LY LZ MM N N NN T X Y to to 31 to to 1 to st 3 st st st st M3 x. 3 M x (1.) (.) (.) (.) M x... M x M x... M x Z to to 31 to to 1 to to 1 to to st 3 st st st st st st st (9.) (.) (92.) (.) ( ) in S and Z dimensions: With auto switch to 1 to to st st st 111 pplicable Part no. bore NTJ- NTJ- NTJ-. C Material: Iron d M3 x. M x. M x. H

29 ir Cylinder: Standard Type Single cting, Spring Return/Extend Series CJ2 Single cting, Spring Extend: Rod Side Flange Style (F) CJ2F CJ2F Cover surface T Mounting nut Piping port M x..3.3 CJ2F, For details of the mounting nut, refer to page C D F F FC FT FX FY FZ G H MM N N NN M3 x. 3 M x x øfc Mounting hole Cover surface 2 x øfc Mounting hole H + Mounting nut H M x. M x..... Z + 2 x Z + 2 x M x 1. M x 1. T to st. (1.).. to 3 st. (.) Single cting, Spring Extend: Double Clevis Style (D) Piping port M x. 31 to st 9. (.) 9 S to st 3. (.) 1 1 to st to st to st 9.3 to st Rod cover side Part no. NTJ- NTJ- NTJ- to st pplicable bore to 31 to 3 st st. Z to st Head cover side Rod End Nut C to st Material: Iron to st 1 to to st st (9.) (.) (92.) (.) ( ) in S and Z dimensions: With auto switch d M3 x. M x. M x. H CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 CJ2D T Z + 2 x H + Piping port M x. +.3 øcdh9.3 Clevis pin (øcdd9.).3 T-bracket For details, refer to page 1. CZ.3 ZZ + 2 x Clevis pin and retaining ring are shipped together. 1.3 to st 9.. C 1 2 to 3 st 3 9 CD (cd) 3.3 CX CZ to st D to st 133 ZZ G 1 to st 139 H 2 2 MM N N R M x. M x. to st to st to st 193 U to st.. to 3 st 31 to st 9 to st 1 S 1 to st to st to st 9 T-bracket Dimensions TC.. TH 29 3 TV to st 11 TW 22 2 to st.. TX 32 3 to 3 st to st TY to st Z 1 to st to st 19 1 to st to st 19 D- Technical data

30 ir Cylinder: Non-rotating Rod Type Double cting, Single Rod Series CJ2K ø, ø With auto switch L F D Mounting style asic style xial foot style Rod side flange style Double clevis style CJ2K L CDJ2K L mm mm Cylinder standard stroke Refer to the standard stroke table on page 9. M9W With auto switch (uilt-in magnet) Head cover port location ø, ø Symbol Nil Perpendicular to axis R xial For configuration, refer to page 9. Double clevis is only available for being perpendicular to axis. pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Grommet Connector Yes Grommet Yes Grommet Connector Indicator light No Yes No Yes Diagnostic indication (2-color indication) Grommet Lead wire length symbols:. m 1 m 3 m m 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire -wire (NPN) 3-wire (NPN equivalent) Nil M L Z Wiring (Output) 2-wire 2 V 2 V Load voltage DC (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ (Example) HCN V, V V V, V V V, V V V How to Order C and mounting model Rail mounting Perpendicular In-line Rail mounting style CDJ2K-- Example and mounting style CDJ2K-- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Made to Order Refer to page 9 for details. Number of auto switches M9N FNV F9 M9P FPV FP M9 FV J9 HC J9C M9NW FNWV F9W M9PW FPW M9W FWV J9W H FV F HNF F9F 2 V 9 2 H 2H V 3 3H 93 V or less 2 V or less 9 C3C CC 3C C 9W H Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. D-9W cannot be mounted on bore size ø cylinder with air cushion. None N Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. Nil S n 2 pcs. 1 pc. n pcs. Lead wire length (m). 1 3 None Pre-wired pplicable load connector (Nil) (M) (L) (Z) (N) Relay, PLC Relay, PLC

31 ir Cylinder: Non-rotating Rod Type Double cting, Single Rod Series CJ2K cylinder which rod does not rotate because of the hexagonal rod shape. Specifications ction Fluid Double acting, Single rod ir Non-rotating accuracy ø: ±1., ø: ±1 Can operate without lubrication. Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Cushion Lubrication 1 MPa. MPa. MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper Not required (Non-lube) CJ1 CJP length tolerance Rod non-rotating accuracy +1. ±1. ±1 CJ2 JIS Symbol Double acting, Single rod Piston speed llowable kinetic energy No freezing.3 J to mm/s.9 J CM2 CG1 Head Cover Port Location Either perpendicular to the cylinder axis or in-line with the cylinder axis is available for basic style. Symbol X XC3 XC XC22 XC1 xial Specifications Perpendicular Made to Order Specifications (For details, refer to pages 133 to 19.) Change of rod end shape Special port location Dual stroke cylinder/double rod type Fluororubber seals With hose nipple Standard Standard stroke, 3,,,,,,, 3,,,,,,, 1, 2 Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Mounting Style and ccessory/for details, refer to page 1. Mounting style Mounting nut Clevis pin Single knuckle joint Double knuckle joint T-bracket Pin and retaining ring are shipped together with double clevis and double knuckle joint. Standard equipment Option Mounting racket Part No. Mounting bracket Foot bracket Flange bracket T-bracket CJ-L CJ-F CJ-T CJK-L CJK-F CJ-T T-bracket is used with double clevis (D). asic style xial foot style Rod side flange style Double clevis style M M1 C2 CS1 CS2 Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. 9 D- Technical data

32 Series CJ2K Specific Product Precautions e sure to read before handling. Refer to front matters and for Safety Instructions and pages 3 to 11 for ctuator and uto Switch Precautions. llowable rotational torque (N m) Caution on Handling Caution 1. During installation, secure the rod cover and tighten by applying an appropriate tightening force to the retaining but or to the rod cover body. If the head cover is secured or the head cover is tightened, the cover could rotate, leading to the deviation. 2. Tighten the retaining screws to an appropriate tightening torque within the range given below. ø:. to 11. N m, ø: 2 to 21 N m 3. In the case of a non-rotating cylinder, do not operate it in such a way that rotational torque would be applied to the piston rod. If rotational torque is applied, the non-rotating guide will become deformed, thus affecting the non-rotating accuracy. ø.2 ø.. To screw a bracket onto the threaded portion at the tip of the piston rod, make sure to retract the piston rod entirely, and place a wrench over the flat portion of the rod that protrudes. To tighten, take precautions to prevent the tightening torque from being applied to the non-rotating guide.. To remove and install the retaining ring for the knuckle pin or the clevis pin, use an appropriate pair of pliers (tool for installing a type C retaining ring). In particular, use a pair of ultra-mini pliers for removing and installing the retaining ring on the ø cylinder.. In the case of auto switch rail mounting style, do not remove the rail that is mounted. ecause retaining screws extend into the cylinder, this could lead to an air leak. Mass asic mass dditional mass per each mm of stroke Mounting bracket mass Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. Specifications ction Maximum operating pressure Minimum operating pressure Cushion Rod non-rotating ø accuracy ø Standard stroke Mounting xial foot style Rod side flange style Double clevis style (With pin) Mounting nut and rod end nut are included in the basic mass. Mounting nut is not attached to the double clevis style, so the mounting nut mass is already subtracted. Calculation: (Example) CJ2KL- asic mass 2 (ø) dditional mass / stroke Cylinder stroke stroke Mounting bracket mass 2 (xial foot style) 2 + / x + 2 = g 2-CJ2K Mounting style Copper and fluorine-free Head cover port location (g) Double acting, Single rod. MPa. MPa Rubber bumper (Standard equipment) ±1. ±1 Same as standard type. (Refer to page 9.) Mountable (and mounting style) asic style, xial foot style, Rod side flange style, Double clevis style Construction (Not able to disassemble) Rod section Component Parts No Description Rod cover Head cover Cylinder tube Piston rod Piston Mounting nut Material luminum alloy luminum alloy Stainless steel Stainless steel rass rass Note nodized nodized Nickel plated No Description umper Piston seal Rod seal Tube gasket Piston gasket Material Rolled steel Urethane NR NR NR NR Note Nickel plated

33 ir Cylinder: Non-rotating Rod Type Double cting, Single Rod Series CJ2K asic Style () CJ2K Head cover port location Mounting nut Piping port 2 x M x. Piping port M x CJ1 CJP Rod section Z + Head cover port location: xial location (R) CJ2 CM2 Refer to page 1 for details of the mounting nut. (SNJ- for ø, SNKJ- for ø) C C F G G H K MM M x M x. N.. N NDh.22.2 NN M x 1. M x 1. S Z CG1 M M1 C2 xial Foot Style (L) CS1 CJ2KL Head cover port location CS2 -.3 Rod cover side Cover surface Mounting nut Piping port 2 x M x. Piping port M x. -.3 Rod section 2 x ølc Mounting hole Z + Head cover port location: xial location (R) Rod End Nut Material: Iron pplicable Part no. bore C d H NTJ- NTJ-.1 M x M x. Refer to page 1 for details of the mounting nut. (SNJ- for ø, SNKJ- for ø) C C F G G H K L LC LH LT LX LY 2 2 LZ 2 2 MM M x. M x. N.. N NN M x 1. M x 1. X Y 9 9 S Z D- 1 Technical data

34 Series CJ2K Rod Side Flange Style (F) CJ2KF Head cover port location.3 Rod cover side Mounting nut Cover surface Piping port 2 x M x. Piping port M x..3 2 x øfc Rod section Mounting hole Z + Head cover port location: xial location (R) Refer to page 1 for details of the mounting nut. (SNJ- for ø, SNKJ- for ø) C 1 2 C 1 2 F F FC.. FT FX FY 2 2 FZ 2 2 G G H 2 2 K.2.2 MM M x. M x. N.. N NN M x 1. M x 1. S Z Double Clevis Style (D) CJ2KD Z + Piping port 2 x M x. øcdh9 +.3 Clevis pin.3 (øcdd9.).3 Rod section T-bracket For details, refer to page 1..3 ZZ + Rod End Nut Clevis pin and retaining ring are shipped together. Material: Iron Part no. pplicable bore C d H NTJ-.1 M x. 3.2 NTJ- 9.2 M x C 1 2 C 1 2 CD(cd) 3.3 CX 3.2. G G 1 23 H 2 2 K.2.2 MM M x. M x. N.. N R S U Z 2 ZZ T-bracket Dimensions TC TH TV TW 22 2 TX 32 3 TY

35 ir Cylinder: Non-rotating Rod Type Single cting, Spring Return/Extend Series CJ2K ø, ø Spring extend With auto switch Spring return Mounting style asic style L xial foot style F Rod side flange style D Double clevis style CJ2K L CDJ2K L mm mm Cylinder standard stroke Refer to the standard stroke table on page. S S With auto switch (uilt-in magnet) Head cover port location ø, ø Symbol Nil Perpendicular to axis R xial ction S Single acting, Spring return T Single acting, Spring extend pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Grommet Connector Indicator light No Yes No Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 2V DC V, V 2-wire V Connector Yes 2V 3-wire (NPN) V, V 3-wire (PNP) Grommet 2-wire Water resistant (2-color indication) With diagnostic output (2-color indication) -wire (NPN) 3-wire (NPN equivalent) Grommet Yes Diagnostic indication (2-color indication) Grommet Lead wire length symbols:. m 1 m 3 m m Nil M L Z (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ (Example) HCN V V, V V V How to Order For configuration, refer to page 9. Single acting, Spring return (S), Clevis style is available only for 9 to the axis. Not applicable to single acting, spring extend (T). Load voltage C 2 V V V or less 2 V or less and mounting M9N M9P M9 HC M9NW M9PW M9W H HNF 93 9 C3C CC 2 3 3C C 9W M9W model Rail mounting Perpendicular In-line FNV F9 FPV FP FV J9 J9C FNWV F9W FPW FWV J9W FV F F9F 9 H 2H 3H H uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Rail mounting style CDJ2K-S- Example and mounting style CDJ2K-S- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. Lead wire length (m). 1 3 None (Nil) (M) (L) (Z) (N) Made to Order Refer to page for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. D-9W cannot be mounted on bore size ø cylinder with air cushion. None N Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. Pre-wired pplicable load connector Relay, PLC Relay, PLC 3 CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 D- Technical data

36 Series CJ2K cylinder which rod does not rotate because of the hexagonal rod shape. Non-rotating accuracy ø: ±1., ø: ±1 Can operate without lubrication. Spring extend Spring return Specifications ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Cushion Lubrication length tolerance Rod non-rotating accuracy Piston speed llowable kinetic energy No freezing Single acting, Spring return/single acting, Spring extend ir 1 MPa. MPa. MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper (standard equipment) Not required (Non-lube) +1. ±1. ±1 to mm/s.3 J.9 J JIS Symbol Single acting, Spring return Single acting, Spring extend Standard Standard stroke, 3,,, 3,,,,,, Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Spring Force Retracted side. 1.2 (N) Extended side 3.3. Mounting Style and ccessory/for details, refer to page. Mounting asic style xial foot style Rod side flange style Double clevis style Symbol X XC1 Made to Order Specifications (For details, refer to pages 13 and 19.) Specifications Change of rod end shape With hose nipple Standard equipment Option Mounting nut Clevis pin Single knuckle joint Double knuckle joint T-bracket Pin and retaining ring are shipped together with double clevis and double knuckle joint. Mounting racket Part No. Mounting bracket Foot bracket CJ-L CJK-L Flange bracket T-bracket CJ-F CJ-T CJK-F CJ-T T-bracket is used with double clevis (D). Precautions e sure to read before handling. Refer to front matters and for Safety Instructions and pages 3 to 11 for ctuator and uto Switch Precautions. Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no.

37 ir Cylinder: Non-rotating Rod Type Single cting, Spring Return/Extend Series CJ2K Mass/Spring Return, ( ): Spring Extend stroke 2(2) 3 stroke 3(3) stroke (3) (g) 3() () 2() Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) 2-CJ2K Mounting style ction Copper and fluorine-free Head cover port location asic mass Mounting bracket mass stroke stroke stroke stroke stroke xial foot style Rod side flange style Double clevis style (With pin) 3(1) 2 (1) 1(1) 1(1) 22(2) 2(23) 2 Mounting nut and rod end nut are included in the basic mass. Mounting nut is not attached to the double clevis style, so the mounting nut mass is already subtracted. Calculation: (Example) CJ2KL-S asic mass (ø- stroke) Mounting bracket mass 2 (xial foot style) + 2 = g Construction (Not able to disassemble) Single acting, Spring return Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. Specifications ction Fluid Maximum operating pressure Minimum operating pressure Cushion Rod non-rotating accuracy Standard stroke Mounting Single acting/spring return, Spring extend ir,. MPa. MPa Rubber bumper (Standard equipment) ø: ±1., ø: ±1 Same as standard type. (Refer to page.) Mountable (and mounting style) asic style, xial foot style, Rod side flange style, Double clevis style CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 Single acting, Spring extend Component Parts No. Description Material Note No. Description Material Note 1 Rod cover luminum alloy nodized 9 umper Urethane 2 Head cover luminum alloy nodized Mounting nut rass Nickel plated 3 Cylinder tube Stainless steel 11 Rolled steel Nickel plated Piston rod Stainless steel Piston seal NR Piston Piston Return spring Spring seat rass rass Piano wire rass Zinc chromated 13 1 Rod seal Tube gasket Piston gasket NR NR NR D- Technical data

38 Series CJ2K Single cting, Spring Return: asic Style () CJ2K S Head cover port location Mounting nut Piping port M x. Piping port M x. Refer to page 1 for details of the mounting nut. (SNJ- for ø, SNKJ- for ø) C 1 2 C 1 2 F G H 2 2 K.2.2 Dimensions by ore size to.. to to to S 1 to to 1 to to 13 to MM M x. M x. to to 93 9 N.. to N Z 1 to 1 NDh.22.2 to 13 1 to NN M x 1. M x 1. to.3.3 Rod section Z + Head cover port location: xial location (R) Symbol Single cting, Spring Return: xial Foot Style (L) CJ2KL S Head cover port location Mounting nut -.3 Rod cover side Cover surface Piping port M x. Piping port M x..3 2 x ølc Rod section Mounting hole Z + Head cover port location: xial location (R) Rod End Nut Refer to page 1 for details of the mounting nut. (SNJ- for ø, SNKJ- for ø) C 1 2 C 1 2 F G H 2 2 K.2.2 L LC.. LH 1 1 LT Dimensions by ore size Symbol to.. to to S to 1 to to 1 to to 13 to LX LY 2 2 to LZ to 93 9 MM M x. M x. to N.. Z Part no. pplicable bore NTJ- NTJ- 1 to 1 N NN M x 1. M x 1. to 13 Material: Iron C d H to M x. M x. X 3.2 Y 9 9 to

39 ir Cylinder: Non-rotating Rod Type Single cting, Spring Return/Extend Series CJ2K Single cting, Spring Return: Rod Side Flange Style (F) CJ2KF S Head cover port location.3 Rod cover side Refer to page 1 for details of the mounting nut. (SNJ- for ø, SNKJ- for ø) C 1 2 C 1 2 F F FC.. FT FX FY 2 2 Dimensions by ore size Symbol Cover surface to to Rod section 2 x øfc Mounting hole Mounting nut Piping port M x. Z + FZ 2 2 G S 31 to to 1 to to 1 to to to to Single cting, Spring Return: Double Clevis Style (D).3 H 2 2 K.2.2 MM M x. M x. N.. Piping port M x. Head cover port location: xial location (R) N NN M x 1. M x 1. Z 31 to to 1 to to 1 to to CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 CJ2KD.3 S Rod section Z + Piping port M x. +.3 øcdh9 Clevis pin.3 (øcdd9.) T-bracket For details, refer to page 1..3 ZZ + Rod End Nut Clevis pin and retaining ring are shipped together T-bracket Dimensions TC TH TV TW C 1 2 C 1 2 CD (cd) 3.3 CX 3.2. G 1 23 H 2 2 K.2.2 MM M x. M x. N.. N R U Material: Iron pplicable Part no. bore C d H NTJ- NTJ M x. M x. Dimensions by ore Symbol S Z Z Z size to to 3 31 to to 1 to to 1 to to to to 3 31 to to 1 to to 1 to to to to 3 31 to to 1 to to 1 to to TX TY D- Technical data

40 Series CJ2K Single cting, Spring Extend: asic Style () CJ2K T Mounting nut Piping port M x. Refer to page 1 for details of the mounting nut. (SNJ- for ø, SNKJ- for ø) C 1 2 C 1 2 F G H 2 2 K.2.2 Dimensions by ore size to.. to 3 31 to 9 to 1 S 1 to to to 9 to 11 to.. MM M x. M x. to 3 31 to 9 9 N.. to 9 N.. Z 1 to 1 NDh to to NN M x 1. M x 1. to Rod section H + Z + 2 x Symbol Single cting, Spring Extend: xial Foot Style (T) CJ2KL T.3 Rod cover side Cover surface Mounting nut Piping port M x. Rod section 2 x ølc Mounting hole H + Z + 2 x Rod End Nut Refer to page 1 for details of the mounting nut. (SNJ- for ø, SNKJ- for ø) C 1 2 C 1 2 F G H 2 2 K.2.2 L LC.. LH 1 1 LT Dimensions by ore size Symbol to.. to 3 31 to 9 to 1 S 1 to to to 9 to 11 to.. LX LY 2 2 to 3 LZ to 9 9 MM N M x.. M x.. to 9 Part no. NTJ- NTJ- Z pplicable bore 1 to 1 N.. NN M x 1. M x 1. to to Material: Iron C d H M x. M x. X 3.2 Y 9 9 to 9

41 ir Cylinder: Non-rotating Rod Type Single cting, Spring Return/Extend Series CJ2K Single cting, Spring Extend: Rod Side Flange Style (F) CJ2KF T -.3 Rod cover side Refer to page 1 for details of the mounting nut. (SNJ- for ø, SNKJ- for ø) C 1 2 C 1 2 F F FC.. FT FX FY 2 2 Dimensions by ore size 2 x øfc Mounting hole Rod sedtion Symbol S to to 3 31 to to 1 to to 1 to to to Cover surface H + Mounting nut Z + 2 x Piping port M x. Single cting, Spring Extend/Double Clevis Style (D) FZ 2 2 G H K.2.2 Z to 3 31 to to MM M x. M x. N.. N.. NN M x 1. M x 1. 1 to to 1 to to CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 CJ2KD T H + Z + 2 x Piping port M x. +.3 øcdh9 Clevis pin.3 (øcdd9.) -.3 Rod sedtion T-bracket -.3 For details, refer to page 1. ZZ + 2 x Rod End Nut Clevis pin and retaining ring are shipped together. Material: Iron CD C C (cd) CX G H K MM N N R U pplicable Part no. bore C d H M x.. 1. NTJ-.1 M x M x NTJ- 9.2 M x. Dimensions by ore Symbol S Z ZZ size to to 3 31 to to 1 to to 1 to to to to 3 31 to to 1 to to 1 to to to to 3 31 to to 1 to to 1 to to T-bracket Dimensions TC TH TV TW TX TY D- Technical data

42 ir Cylinder: uilt-in Speed Controller Type Double cting, Single Rod Series CJ2Z ø, ø With auto switch L F D Mounting style asic style xial foot style Rod side flange style Double clevis style mm mm CJ2Z L Cylinder standard stroke Refer to the standard stroke table on page 1. CDJ2Z L M9W With auto switch (uilt-in magnet) Head cover port location ø, ø Symbol Nil Perpendicular to axis R xial pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Grommet Connector Indicator light No Yes No Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 2V DC V, V 2-wire V Connector Yes 2V 3-wire (NPN) V, V 3-wire (PNP) Grommet 2-wire Water resistant (2-color indication) With diagnostic output (2-color indication) -wire (NPN) 3-wire (NPN equivalent) Grommet Yes Diagnostic indication (2-color indication) Grommet Lead wire length symbols:. m 1 m 3 m m Nil M L Z (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ (Example) HCN V V, V V V How to Order For configuration, refer to page 1. Double clevis is only available for being perpendicular to axis. Load voltage C 2 V V V or less 2 V or less model and Rail mounting mounting Perpendicular In-line M9N FNV F9 M9P FPV FP M9 FV J9 HC J9C M9NW FNWV F9W M9PW FPW M9W FWV J9W H FV F HNF F9F 9 H 2H 3H 93 9 H C3C CC 2 3 3C C 9W uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Rail mounting style CDJ2Z-- Example and mounting style CDJ2Z-- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. Lead wire length (m). 1 3 None (Nil) (M) (L) (Z) (N) Made to Order Refer to page 1 for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. D-9W cannot be mounted on bore size ø cylinder with air cushion. None N Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. Pre-wired pplicable load connector Relay, PLC Relay, PLC

43 ir Cylinder: uilt-in Speed Controller Type Double cting, Single Rod Series CJ2Z Space-saving air cylinder with speed controller built-in cylinder cover JIS Symbol Double acting, Single rod Symbol X XC1 Made to Order Specifications (For details, refer to pages 13 and 19.) Specifications Change of rod end shape With hose nipple Precautions Specifications ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Cushion Lubrication length tolerance Speed controller Piston speed llowable kinetic energy No freezing Standard Double acting, Single rod ir 1 MPa. MPa. MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper Not required (Non-lube) +1. uilt-in to mm/s.3 J.9 J Standard stroke, 3,,,,,,, 3,,,,,,, 1, 2 Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Mounting Style and ccessory/for details, refer to page 1. Mounting nut Clevis pin Single knuckle joint Double knuckle joint T-bracket Pin and retaining ring are shipped together with double clevis and double knuckle joint. Standard equipment Option Mounting Head Cover Port Location asic style xial foot style Rod side flange style Either perpendicular to the cylinder axis or in-line with the cylinder axis is available for basic style. Double clevis style CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 Refer to page before handling. xial Perpendicular Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. D- 1 Technical data

44 Series CJ2Z Mass asic mass dditional mass per each mm of stroke Mounting bracket mass xial foot style Rod side flange style Double clevis style (With pin) (g) 3. 2 Mounting nut and rod end nut are included in the basic mass. Mounting nut is not attached to the double clevis style, so the mounting nut mass is already subtracted. Calculation: (Example) CJ2ZL- asic mass (ø) dditional mass / stroke Cylinder stroke stroke Mounting bracket mass (xial foot style) + / x + = g Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) 2-CJ2Z Mounting style Copper and fluorine-free Head cover port location Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. Specifications ction Maximum operating pressure Minimum operating pressure Cushion Standard stroke Mounting Double acting, Single rod,. MPa. MPa Rubber bumper (Standard equipment) Same as standard type. (Refer to page 1.) Mountable (and mounting style) asic style, xial foot style, Rod side flange style, Double clevis style Construction (Not able to disassemble) Component Parts No Description Rod cover Head cover Cylinder tube Piston rod Piston umper Speed controller needle Check packing sleeve Steel balls Retaining ring Material luminum alloy luminum alloy Stainless steel Stainless steel rass Urethane Stainless steel rass earing steel Carbon tool steel Note nodized nodized lack zinc chromated No Description Mounting nut Piston seal Rod seal Check seal Check seal Tube gasket Piston gasket Needle seal Material rass Rolled steel NR NR NR NR NR NR NR Note Nickel plated Nickel plated 2

45 ir Cylinder: uilt-in Speed Controller Type Double cting, Single Rod Series CJ2Z asic Style () CJ2Z Head cover port location Mounting nut Piping port 2 x M x. Piping port M x. CJ1 CJP -.3 CJ2 Z + Head cover port location: xial location (R) CM2 CG1 For details of the mounting nut, refer to page C 1 2 D F G.. G.. H 2 2 MM M x. M x. N N 1 1 NDh NN M x 1. M x 1. W W WW.. S 3 Z M M1 C2 xial Foot Style (L) CJ2ZL Head cover port location CS1 CS2 Cover surface Mounting nut Piping port 2 x M x. Head cover port location: xial location (R) Piping port M x x ølc Mounting hole Z + Rod End Nut Part no. pplicable bore NTJ- NTJ- C Material: Iron d M x. M x. H 3.2 For details of the mounting nut, refer to page 1. C D F G G H 2 2 L. 23 LC.. LH 9 1 LT LX 2 33 LY. 2 LZ 32 2 MM M x. M x. N N 1 1 NN M x 1. M x 1. S 3 W W WW X Y 9 Z D- 3 Technical data

46 Series CJ2Z Rod Side Flange Style (F) CJ2ZF Head cover port location Cover surface Mounting nut Piping port 2 x M x. Piping port M x x øfc Mounting hole Z + Head cover port location: xial location (R) For details of the mounting nut, refer to page C 1 2 D F F FC.. FT FX 2 33 FY 1 2 FZ 32 2 G.. G.. H 2 2 MM M x. M x. N N 1 1 NN M x 1. M x 1. W W WW.. S 3 Z Double Clevis Style (D) CJ2ZD Z + Piping port 2 x M x. øcdh9 +.3 Clevis pin (øcdd9.3.) -.3 T-bracket For details, refer to page 1. CZ -.3 Rod End Nut x øtc ZZ + Material: Iron Part no. NTJ- NTJ- pplicable bore C d M x. M x. H 3.2 Clevis pin and retaining ring are shipped together. TC TH 29 3 C 1 2 T-bracket Dimensions TV CD (cd) 3.3 TW 22 2 CX 3.2. TX 32 3 CZ 1.3 D TY G.. G H 2 2 MM M x. M x. N N 31 3 R S 3 U W W WW.. Z 99 2 ZZ 1 1

47 ir Cylinder: uilt-in Speed Controller Type Double cting, Double Rod Series CJ2ZW ø, ø With auto switch Mounting style asic style L Foot style F Flange style mm mm CJ2ZW L CDJ2ZW L With auto switch (uilt-in magnet) Cylinder standard stroke Refer to the standard stroke table on page. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Grommet Connector Yes Grommet Yes Grommet Connector Diagnostic indication (2-color indication) Grommet Indicator light No Yes No Yes Lead wire length symbols:. m 1 m 3 m m -wire (NPN) 3-wire (NPN equivalent) Nil M L Z Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 2-wire 2 V 2 V Load voltage DC (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ (Example) HCN V, V V V, V V V, V V V How to Order M9W C 2 V V V or less 2 V or less and mounting M9N M9P M9 HC M9NW M9PW M9W H HNF C3C CC model Rail mounting Perpendicular In-line FNV FPV FV J9C FNWV FWV FV 2 3 3C C 9W F9 FP J9 F9W FPW J9W F F9F H 2H 3H H uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Rail mounting style CDJ2ZW-- Example and mounting style CDJ2ZW-- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. Made to Order Refer to page for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Lead wire length (m). 1 3 None Pre-wired pplicable load connector (Nil) (M) (L) (Z) (N) Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. D-9W cannot be mounted on bore size ø cylinder with air cushion. None N Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. Relay, PLC Relay, PLC CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 D- Technical data

48 Series CJ2ZW Space-saving air cylinder with speed controller built-in cylinder cover Specifications ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Cushion Lubrication length tolerance Speed controller Piston speed llowable kinetic energy No freezing Double acting, Single rod ir 1 MPa. MPa.1 MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper Not required (Non-lube) +1. uilt-in to mm/s.3 J.9 J Standard JIS Symbol Double acting, Double rod Standard stroke, 3,,, 3,, Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Mounting Style and ccessory/for details, refer to page 1. Mounting asic style Foot style Flange style Made to Order Specifications (For details, refer to pages 13 and 19.) Symbol Specifications X Change of rod end shape XC1 With hose nipple Precautions Refer to page before handling. Standard Mounting nut equipment Single knuckle joint Option Double knuckle joint Knuckle pin and retaining ring are shipped together with double knuckle joint. Mounting racket Part No. Mounting bracket Foot bracket Flange bracket CJ-L CJ-F CJ-L CJ-F Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no.

49 ir Cylinder: uilt-in Speed Controller Type Double cting, Double Rod Series CJ2ZW Mass (g) Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) asic mass 2-CJ2ZW Mounting style Head cover port location dditional mass per each mm of stroke 9 Copper and fluorine-free Mounting bracket mass Foot style Flange style are included in the basic mass. Calculation: (Example) CJ2ZWL- asic mass (ø) dditional mass / stroke Cylinder stroke stroke Mounting bracket mass (xial foot style) + / x + = g Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. CJ1 CJP CJ2 CM2 CG1 Specifications ction Maximum operating pressure Minimum operating pressure Cushion Standard stroke Mounting Double acting, Double rod,. MPa.1 MPa Rubber bumper, 3,, Mountable (and mounting style) asic style, Foot style, Flange style M M1 C2 CS1 CS2 Construction (Not able to disassemble) Component Parts No Description Rod cover Cylinder tube Piston rod Piston umper Speed controller needle Steel balls Mounting nut Material luminum alloy Stainless steel Stainless steel rass Urethane Stainless steel earing steel rass Note nodized Nickel plated No Description Piston seal Rod seal Check seal Tube gasket Piston gasket Needle seal Material Rolled steel NR NR NR NR NR NR Note Nickel plated D- Technical data

50 Series CJ2ZW asic Style () CJ2ZW Mounting nut Piping port 2 x M x..3.3 Z + 2 x H + For details of the mounting nut, refer to page C 1 2 D F G.. H 2 2 MM M x. M x. N NDh NN M x 1. M x 1. S W WW.. Z 2 3 Foot Style (L) CJ2ZWL Mounting nut Cover surface Piping port 2 x M x. 2 x ølc Mounting hole Z + 2 x H + Rod End Nut Part no. NTJ- NTJ- pplicable bore C Material: Iron d M x. M x. H 3.2 For details of the mounting nut, refer to page D F L. 23 LC.. LH 9 1 LT LX 2 33 LY. 2 LZ 32 2 G.. H 2 2 MM M x. M x. N NN M x 1. M x 1. S W WW.. X Y 9 Z 2 3

51 ir Cylinder: uilt-in Speed Controller Type Double cting, Double Rod Series CJ2ZW Flange Style (F) CJ2ZWF 2 x øfc Mounting nut Cover surface Mounting hole Piping port 2 x M x. CJ1 CJP CJ2 CM2 Z + 2 x H + CG1 M Rod End Nut M1 C2 CS1 Part no. NTJ- NTJ- pplicable bore C Material: Iron d M x. M x. H 3.2 CS2 For details of the mounting nut, refer to page D F F FC.. FT FX 2 33 FY 1 2 FZ 32 2 G.. H 2 2 MM M x. M x. N NN M x 1. M x 1. S W WW.. Z 2 3 D- 9 Technical data

52 ir Cylinder: Low Friction Type Double cting, Single Rod Series CJ2Q ø, ø With auto switch L F D Mounting style asic style xial foot style Rod side flange style Double clevis style CJ2Q CDJ2Q mm mm With auto switch (uilt-in magnet) Head cover port location ø, ø Symbol Nil Perpendicular to axis R xial Cylinder standard stroke Refer to the standard stroke table on page 91. M9W pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Grommet Connector Yes Grommet Yes Grommet Connector Diagnostic indication (2-color indication) Grommet Indicator light No Yes No Yes Lead wire length symbols:. m 1 m 3 m -wire (NPN) 3-wire (NPN equivalent) Nil M L Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 2-wire 2 V 2 V L L Load voltage DC (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ V, V V V, V V V, V V V How to Order C 2 V V V or less 2 V or less For configuration, refer to page 92. Double clevis is only available for being perpendicular to axis. and mounting M9N M9P M9 HC M9NW M9PW M9W H HNF C3C CC model Rail mounting Perpendicular In-line FNV FPV FV J9C FNWV FWV FV 2 3 3C C 9W F9 FP J9 F9W FPW J9W F F9F H 2H 3H H uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Rail mounting style CDJ2Q-- Example and mounting style CDJ2Q-- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. Made to Order Refer to page 91 for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Lead wire length (m). 1 3 None Pre-wired pplicable load connector (Nil) (M) (L) (Z) (N) Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. m Z Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. 9 Relay, PLC Relay, PLC

53 ir Cylinder: Low Friction Type Double cting, Single Rod Series CJ2Q Specially designed to keep friction of the piston to a minimum. Suitable for contact-pressure control requiring smooth operation at low pressures. Low sliding resistance Minimum operating pressure:.3 MPa pplication Example Low friction cylinder is used in combination with precision regulator (Series IR). Driving roller Winding roller Precision regulator Precision regulator Moving object CJ1 CJP CJ2 CM2 Specifications CG1 JIS Symbol Double acting, Single rod ction Fluid Proof pressure Maximum operating pressure Double acting, Single rod ir 1 MPa. MPa M M1 C2 Minimum operating pressure mbient and fluid temperature Cushion.3 MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper CS1 CS2 Lubrication Not applicable length tolerance +1. Symbol Made to Order Specifications (For details, refer to pages 13 and 19.) Specifications Piston speed llowable kinetic energy No freezing.3 J to mm/s.9 J X XC1 Change of rod end shape With hose nipple Standard Standard stroke Precautions Refer to page before handling., 3,,,,,,, 3,,,,,,, 1, 2 Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Refer to pages 11 to 3 for cylinders with an auto switch. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. D- 91 Technical data

54 Series CJ2Q Mounting Style and ccessory/for details, refer to page 1. Standard equipment Option Pin and retaining ring are shipped together with double clevis and double knuckle joint. Mounting racket Part No. Mounting bracket Foot bracket Flange bracket T-bracket CJ-L CJ-F CJ-T CJ-L CJ-F CJ-T T-bracket is used with double clevis (D). Mass Mounting Mounting nut Clevis pin Single knuckle joint Double knuckle joint T-bracket asic style asic mass dditional mass per each mm of stroke Mounting bracket mass xial foot style Rod side flange style Double clevis style (With pin) xial foot style 2 Rod side flange style Double clevis style. 2 Mounting nut and rod end nut are included in the basic mass. Mounting nut is not attached to the double clevis style, so the mounting nut mass is already subtracted. Calculation: (Example) CJ2QL- asic mass 2 (ø) dditional mass / stroke Cylinder stroke stroke Mounting bracket mass (xial foot style) 2 + / x + = g (g) Head Cover Port Location Either perpendicular to the cylinder axis or in-line with the cylinder axis is available for basic style. xial Perpendicular Sliding Resistance of the Low Friction Side Sliding resistance (MPa) Operating pressure (MPa) Conversion into the cylinder operating pressure: ø ø 92

55 ir Cylinder: Low Friction Type Double cting, Single Rod Series CJ2Q Construction (Not able to disassemble) CJ1 CJP CJ2 CM2 CG1 Component Parts No. Description 1 Rod cover 2 Head cover 3 Cylinder tube Piston rod Piston Mounting nut Material luminum alloy luminum alloy Stainless steel Stainless steel rass rass Note nodized nodized Nickel plated No Description umper Piston seal Rod seal Tube gasket Piston gasket Material Rolled steel Urethane NR NR NR NR Note Nickel plated For low friction For low friction M M1 C2 CS1 CS2 asic Style () CJ2Q Head cover port location Mounting nut Piping port 2 x M x. Piping port M x. Z + Head cover port location: xial location (R) Rod End Nut For details of the mounting nut, refer to page C 1 2 D F G G H 2 2 MM M x. M x. N.. N For dimensions of each mounting bracket, refer to pages to. ND Part no. pplicable bore NTJ- NTJ- NN M x 1. M x 1. Material: Iron C d H M x. M x. S 3.2 Z 93 D- Technical data

56 ir Cylinder: Direct Mount Type Double cting, Single Rod Series CJ2R ø, ø How to Order With auto switch mm mm Mounting style ottom mounting style CJ2R CDJ2R With auto switch (uilt-in magnet) Head cover port location ø, ø Symbol Nil Perpendicular to axis R xial For configuration, refer to page 9. Cylinder standard stroke Refer to the standard stroke table on page 9. M9W Rail mounting style CDJ2R-- Example and mounting style CDJ2R-- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Made to Order Refer to page 9 for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Grommet Connector Yes Grommet Yes Grommet Connector Diagnostic indication (2-color indication) Grommet Indicator light No Yes No Yes Lead wire length symbols:. m 1 m 3 m 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire -wire (NPN) 3-wire (NPN equivalent) Nil M L Wiring (Output) 2-wire 2 V 2 V Load voltage DC (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ V, V V V, V V V, V V V C M9N FNV F9 M9P M9 HC M9NW FPV FV J9C FP J9 FNWV F9W M9PW M9W H HNF FWV FV FPW J9W F F9F 2 V 9 2 H 2H V 3 3H 93 9 C3C CC 3C C 9W H Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. V or less 2 V or less and mounting model Rail mounting Perpendicular In-line Lead wire length (m). 1 3 None Pre-wired pplicable load connector (Nil) (M) (L) (Z) (N) m Z Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. 9 Relay, PLC Relay, PLC

57 ir Cylinder: Direct Mount Type Double cting, Single Rod Series CJ2R Specifications Series CJ2R direct mount cylinder can be installed directly through the use of a square rod cover. ction Fluid Double acting, Single rod ir Proof pressure 1 MPa Maximum operating pressure. MPa Minimum operating pressure mbient and fluid temperature Cushion Lubrication. MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper Not required (Non-lube) CJ1 CJP length tolerance Piston speed llowable kinetic energy +1. to mm/s.3 J.9 J CJ2 CM2 No freezing CG1 JIS Symbol Double acting, Single rod Standard Standard stroke, 3,,,,,,, 3,,,,,,, 1, 2 Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) M M1 C2 CS1 Head Cover Port Location CS2 Made to Order Specifications (For details, refer to pages 13, and 19.) Either perpendicular to the cylinder axis or in-line with the cylinder axis is available for basic style. Symbol Specifications X Change of rod end shape XC22 XC1 Fluororubber seals With hose nipple xial Perpendicular Precautions Refer to page before handling. Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. Mass asic mass 3 dditional mass per each mm of stroke is included in the basic mass. Calculation: (Example) CJ2R- asic mass 3 (ø) dditional mass / stroke Cylinder stroke stroke 3 + / x = g (g) 1.. D- 9 Technical data

58 Series CJ2R Clean Series Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) -CJ2R Head cover port location 2-CJ2R Head cover port location Clean Series ir cylinder which is applicable for the system which discharges leakage from the rod section directly into the outside of clean room by relief port and making an actuator s rod section having a double seal construction. Copper and fluorine-free Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. Specifications ction Maximum operating pressure Minimum operating pressure Cushion Standard stroke Mounting Double acting, Single rod,. MPa. MPa Rubber bumper Same as the standard. (Refer to page 9.) Mountable (and mounting style) ottom mounting style Specifications ction Maximum operating pressure Minimum operating pressure Cushion Standard stroke Mounting, Double acting, Single rod. MPa. MPa Rubber bumper (Standard equipment) Same as standard type. (Refer to page 9.) Mountable (and mounting style) ottom mounting style For details, specifications about the Clean Series, refer to the separate catalog Pneumatic Clean Series. -CJ2R (Clean series) Construction (Not able to disassemble) 9

59 ir Cylinder: Direct Mount Type Double cting, Single Rod Series CJ2R Construction (Not able to disassemble) CJ1 CJP CJ2 CM2 CG1 M Component Parts M1 No. 1 Description Rod cover Material luminum alloy Note nodized No. Description umper Material Urethane Note C2 2 3 Head cover Cylinder tube luminum alloy Stainless steel nodized 9 Piston seal Rod seal NR NR CS1 Piston rod Piston Stainless steel rass 11 Piston gasket Tube gasket NR NR CS2 Rolled steel Nickel plated ottom Mounting Style CJ2R Head cover port location Piping port 2 x M x. Head cover port location: xial location (R) Piping port M x. Z + Rod End Nut Part no. NTJ- NTJ- pplicable bore C Material: Iron d M x. M x. H 3.2 D- 1.3 C 1 2 D G G H 2 2 L 23 2 L 2 LD ø3., ø. counterbore depth ø., ø counterbore depth LH LX MM M x. M x. N N X 2 2 Y S Z Technical data 9

60 ir Cylinder: Direct Mount Type Single cting, Spring Return/Extend Series CJ2R ø, ø With auto switch With auto switch (uilt-in magnet) CJ2R CDJ2R Cylinder standard stroke Refer to the standard stroke table on page 99. mm mm uilt-in Magnet Cylinder Model ction Mounting style S Single acting, Spring return ottom mounting style T Single acting, Spring extend Rail mounting style CDJ2R-S- Example and mounting style CDJ2R-S- S M9W pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Grommet Connector Yes Grommet Yes Grommet Connector Diagnostic indication (2-color indication) Grommet Indicator light No Yes No Yes Lead wire length symbols:. m 1 m 3 m m 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire -wire (NPN) 3-wire (NPN equivalent) Nil M L Z Wiring (Output) 2-wire 2 V 2 V S Head cover port location ø, ø Symbol Nil Perpendicular to axis R xial Load voltage DC (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ (Example) HCN V, V V V, V V V, V V V How to Order For configuration, refer to page 99. Not applicable to single acting, spring extend (T). C V or less 2 V or less and mounting model Rail mounting Perpendicular In-line Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. Made to Order Refer to page 99 for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Lead wire length (m). 1 3 None Pre-wired pplicable load connector (Nil) (M) (L) (Z) (N) M9N FNV F9 M9P M9 HC M9NW FPV FV J9C FP J9 FNWV F9W M9PW M9W H HNF FWV FV FPW J9W F F9F 2 V 9 2 H 2H V 3 3H 93 9 C3C CC 3C C 9W H Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. None N Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. 9 Relay, PLC Relay, PLC

61 ir Cylinder: Direct Mount Type Single cting, Spring Return/Extend Series CJ2R Series CJ2R direct mount cylinder can be installed directly through the use of a square rod cover. Specifications ction Fluid Single acting, Spring return/single acting, Spring extend ir Proof pressure 1 MPa Maximum operating pressure. MPa Minimum operating pressure mbient and fluid temperature Cushion Lubrication. MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper Not required (Non-lube) CJ1 CJP length tolerance Piston speed llowable kinetic energy +1. to mm/s.3 J.9 J CJ2 CM2 No freezing CG1 Standard M Standard stroke, 3,, M1 JIS Symbol Single acting, Spring return Single acting, Spring extend, 3,,,,,, Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) ccessory/for details, refer to page 1. Standard equipment Option Single knuckle joint, Double knuckle joint Knuckle pin and retaining ring are shipped together with double knuckle joint. C2 CS1 CS2 Spring Force Retracted side. 1.2 (N) Extended side 3.3. Made to Order Specifications (For details, refer to pages 13 and 19.) Head Cover Port Location Symbol X XC1 Specifications Change of rod end shape With hose nipple Either perpendicular to the cylinder axis or in-line with the cylinder axis is available for basic style. Precautions Refer to page before handling. xial Perpendicular Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. D- 99 Technical data

62 Series CJ2R Mass Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) Spring Return stroke 3 stroke stroke Mass stroke stroke (g) 2-CJ2R Copper and fluorine-free ction Head cover port location Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. stroke stroke stroke is included in the mass. Spring Extend (g) Specifications ction Max. operating pressure Min. operating pressure, Single acting, Spring return; Single acting, Spring extend. MPa. MPa stroke 3 stroke stroke Cushion Standard stroke Mounting Rubber bumper (Standard equipment) Same as standard type. (Refer to page 99.) Mountable (and mounting style) ottom mounting style Mass stroke stroke 13 stroke 192 stroke 22 stroke 2 is included in the mass. Construction (Not able to disassemble) Component Parts No Description Rod cover Head cover Cylinder tube Piston rod Piston Piston Return spring Material luminum alloy luminum alloy Stainless steel Stainless steel rass rass Piano wire Note nodized nodized Zinc chromated No Description Spring seat umper Piston seal Tube gasket Piston gasket Rod seal Material rass Urethane Rolled steel NR NR NR NR Note Nickel plated

63 ir Cylinder: Direct Mount Type Single cting, Spring Return/Extend Series CJ2R Single cting: ottom Mounting Style Spring return: CJ2R S Head cover port location reathing hole Piping port M x. Piping port M x..3 CJ1 Z + Head cover port location: xial location (R) CJP CJ2 CM2 Spring extend: CJ2R T CG1 X + Piping port M x. reathing hole M M1.3 C2 CS1 H + Z + 2 x CS2 Rod End Nut Material: Iron Part no. pplicable bore C d H NTJ- NTJ M x. M x C 1 2 D G H 2 2 L 23 2 L 2 LD ø3., ø. counterbore depth ø., ø counterbore depth LH LX MM M x. M x. N N X 2 2 Dimensions by : Spring Return Symbol S Z ore size to to 3 31 to to 1 to to 1 to to to to 3 31 to to 1 to to 1 to to Dimensions by : Spring Extend (Dimensions not mentioned in the below table are the same as the above table.) G N N S Z to to 3 31 to to 1 to to 1 to to to to 3 31 to to 1 to to 1 to Y to 9 1 D- Technical data

64 ir Cylinder: Direct Mount, Non-rotating Rod Type Double cting, Single Rod Series CJ2RK ø, ø How to Order With auto switch Mounting style ottom mounting style mm mm CJ2RK CDJ2RK With auto switch (uilt-in magnet) Head cover port location ø, ø Symbol Nil Perpendicular to axis R xial For configuration, refer to page 3. Cylinder standard stroke Refer to the standard stroke table on page 3. M9W uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Rail mounting style CDJ2RK-- Example and mounting style CDJ2RK-- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. Made to Order Refer to page 3 for details. Number of auto switches Nil S n 2 pcs. 1 pc. n pcs. pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Grommet Connector Yes Grommet Yes Grommet Connector Indicator light No Yes No Yes Diagnostic indication (2-color indication) Grommet Lead wire length symbols:. m 1 m 3 m m 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire -wire (NPN) 3-wire (NPN equivalent) Nil M L Z Wiring (Output) 2-wire 2 V 2 V Load voltage DC (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ (Example) HCN V, V V V, V V V, V V V C M9N FNV F9 M9P M9 HC M9NW FPV FV J9C FP J9 FNWV F9W M9PW M9W H HNF FWV FV FPW J9W F F9F 2 V 9 2 H 2H V 3 3H 93 9 C3C CC 3C C 9W H Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. V or less 2 V or less and mounting model Rail mounting Perpendicular In-line Lead wire length (m). 1 3 None Pre-wired pplicable load connector (Nil) (M) (L) (Z) (N) None N Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. 2 Relay, PLC Relay, PLC

65 ir Cylinder: Direct Mount, Non-rotating Rod Type Double cting, Single Rod Series CJ2RK cylinder which rod does not rotate because of the hexagonal rod shape. Non-rotating accuracy ø: ±1., ø: ±1 JIS Symbol Double acting, Single rod Specifications No freezing ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Cushion Lubrication length tolerance Rod non-rotating accuracy Piston speed llowable kinetic energy Standard ccessory/for details, refer to page 1. Double acting, Single rod ir 1 MPa. MPa. MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper Not required (Non-lube) ± to mm/s Standard stroke, 3,,,,,,, 3,,,,,,, 1, 2 Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Standard equipment Option Knuckle pin and retaining ring are shipped together with double knuckle joint. ±1.3 J.9 J Single knuckle joint, Double knuckle joint CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 Made to Order Specifications (For details, refer to pages 13 and 19.) Head Cover Port Location Either perpendicular to the cylinder axis or in-line with the cylinder axis is available for basic style. Symbol X XC1 Specifications Change of rod end shape With hose nipple xial Perpendicular Precautions Refer to page 2 and before handling. Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. Mass asic mass dditional mass per each mm of stroke 3 is included in the basic mass. Calculation: (Example) CJ2RK- asic mass 3 (ø) dditional mass / stroke Cylinder stroke stroke 3 + / x = g (g) D- Technical data

66 Series CJ2RK Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) 2-CJ2RK Copper and fluorine-free Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. Specifications ction Maximum operating pressure Minimum operating pressure Cushion Standard stroke Mounting Head cover port location, Double acting, Single rod. MPa. MPa Rubber bumper (Standard equipment) Same as standard type. (Refer to page 3.) Mountable (and mounting style) ottom mounting style Caution Caution on Handling <When mounting> void using the air cylinder in such a way that rotational torque would be applied to the piston rod because this will deform the non-rotating guide, thus affecting the non-rotating accuracy. ø ø llowable rotational torque (N m).2. Operate the cylinder in such a way that the load to the piston rod is always applied in the axial direction. To screw a bracket onto the threaded portion at the tip of the piston rod, make sure to retract the piston rod entirely, and place a wrench over the flat portion of the rod that protrudes. Tighten it by giving consideration to prevent the tightening torque from being applied to the non-rotating guide.

67 ir Cylinder: Direct Mount, Non-rotating Rod Type Double cting, Single Rod Series CJ2RK Construction (Not able to disassemble) CJ1 CJP CJ2 CM2 Component Parts No. Description 1 Rod cover 2 Head cover 3 Cylinder tube Piston rod Piston Material luminum alloy luminum alloy Stainless steel Stainless steel rass Rolled steel Note nodized nodized Nickel plated No Description umper Piston seal Rod seal Piston gasket Tube gasket Material Urethane NR NR NR NR Note CG1 M M1 C2 CS1 CS2 ottom Mounting Style CJ2RK Head cover port location Piping port 2 x M x. Piping port ø.3 2 x øld Rod section Z +.3 Head cover port location: xial location (R) Rod End Nut Material: Iron Part no. NTJ- NTJ- pplicable bore C d M x. M x. H C 1 2 G G H 2 2 K.2.2 L 23 2 L 2 LD ø3., ø. counterbore depth ø., ø counterbore depth LH LX MM M x. M x. N N X 2 2 Y S Z D- Technical data

68 ir Cylinder: Direct Mount, Non-rotating Rod Type Single cting, Spring Return/Extend Series CJ2RK ø, ø How to Order With auto switch mm mm Mounting style ottom mounting style CJ2RK S CDJ2RK S With auto switch (uilt-in magnet) Head cover port location ø, ø Symbol Nil Perpendicular to axis R xial For configuration, refer to page 3. Not applicable to single acting, spring extend (T). Cylinder standard stroke Refer to the standard stroke table on page. ction S Single acting, Spring return T Single acting, Spring extend M9W uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Rail mounting style CDJ2RK-S- Example and mounting style CDJ2RK-S- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. Made to Order Refer to page for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Grommet Connector Yes Grommet Yes Grommet Connector Indicator light No Yes No Yes Diagnostic indication (2-color indication) Grommet Lead wire length symbols:. m 1 m 3 m m 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire -wire (NPN) 3-wire (NPN equivalent) Nil M L Z Wiring (Output) 2-wire 2 V 2 V Load voltage DC (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ (Example) HCN V, V V V, V V V, V V V C M9N FNV F9 M9P M9 HC M9NW FPV FV J9C FP J9 FNWV F9W M9PW M9W H HNF FWV FV FPW J9W F F9F 2 V 9 2 H 2H V 3 3H 93 9 C3C CC 3C C 9W H Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. V or less 2 V or less and mounting model Rail mounting Perpendicular In-line Lead wire length (m). 1 3 None Pre-wired pplicable load connector (Nil) (M) (L) (Z) (N) None N Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. Relay, PLC Relay, PLC

69 ir Cylinder: Direct Mount, Non-rotating Rod Type Single cting, Spring Return/Extend Series CJ2RK cylinder which rod does not rotate because of the hexagonal rod shape. Specifications ction Fluid Single acting, Spring return/single acting, Spring extend ir Non-rotating accuracy ø: ±1., ø: ±1 Can operate without lubrication. Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Cushion Lubrication 1 MPa. MPa. MPa Without auto switch: C to C, With auto switch: C to C Rubber bumper Not required (Non-lube) CJ1 CJP length tolerance Rod non-rotating accuracy ± ±1 CJ2 Piston speed to mm/s CM2 llowable kinetic energy No freezing.3 J.9 J CG1 Standard Standard stroke, 3,,, 3,,,,,, Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) ccessory/for details, refer to page 1. Standard equipment Option Single knuckle joint, Double knuckle joint Knuckle pin and retaining ring are shipped together with double knuckle joint. M M1 C2 CS1 CS2 JIS Symbol Single acting, Spring return Single acting, Spring extend Spring Force (N) Retracted side Extended side Symbol X XC1 Made to Order Specifications (For details, refer to pages 13 and 19.) Specifications Change of rod end shape With hose nipple Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. Precautions Refer to page 2 and before handling. D- Technical data

70 Series CJ2RK Mass Copper and Fluorine-free ir Cylinder (For CRT manufacturing process) Spring Return stroke 3 stroke stroke Mass stroke stroke (g) 2-CJ2RK Copper and fluorine-free ction Head cover port location Eliminates the effects by copper based ions and fluorine based resins, etc. over the color cathode ray tube. Making copper based materials into electroless nickel plated treatment or changing them to the non-copper materials in order to prevent copper ions from generating. stroke stroke stroke is included in the mass. Spring Extend (g) Specifications ction Max. operating pressure Min. operating pressure, Single acting, Spring return/single acting, Spring extend. MPa. MPa stroke 3 stroke stroke Cushion Standard stroke Mounting Rubber bumper (Standard equipment) Same as standard type. (Refer to page.) Mountable (and mounting style) ottom mounting style Mass stroke stroke 13 stroke 192 stroke 22 stroke 2 is included in the mass. Construction (Not able to disassemble) Single acting, Spring return Single acting, Spring extend Component Parts No Description Rod cover Head cover Cylinder tube Piston rod Piston Piston Return spring Spring seat Material luminum alloy luminum alloy Stainless steel Stainless steel rass rass Piano wire rass Note nodized nodized Zinc chromated No Description umper Piston seal Tube gasket Piston gasket Rod seal Material Urethane Rolled steel NR NR NR NR Note Nickel plated

71 ir Cylinder: Direct Mount, Non-rotating Rod Type Single cting, Spring Return/Extend Series CJ2RK Single cting: ottom Mounting Style Spring return: CJ2RK S Head cover port location reathing hole Piping port M x. Piping port.3 CJ1 CJP Rod section Z + Head cover port location: xial location (R) CJ2 CM2 CG1 Spring extend: CJ2RK T M X + Piping port M x. reathing hole M1 C2 CS1.3 CS2.3 H + Z + 2 x Rod End Nut Material: Iron Part no. NTJ- NTJ- pplicable bore C d M x. M x. H C 1 2 G H 2 2 K.2.2 Dimensions by : Spring Return Symbol L 23 2 L 2 LD ø3., ø. counterbore depth ø., ø counterbore depth LH LX MM M x. M x. S Z to to 3 31 to to 1 to to 1 to to to to 3 31 to to 1 to to 1 to to Dimensions by : Spring Extend (Dimensions not mentioned in the below table are the same as the above table.) S Z G N N to to 3 31 to to 1 to to 1 to to to to 3 31 to to 1 to to 1 to N N X 2 2 Y to 9 9 D- Technical data

72 ir Cylinder: With End Lock Series CJ2 ø How to Order With auto switch Mounting Style asic style L xial foot style F Rod side flange style D Double clevis style Note) Note) Rod end lock only. CJ2 CDJ2 With auto switch (uilt-in magnet) Cylinder standard stroke Refer to the standard stroke table on page 111. pplicable uto Switch/Refer to pages 3 to 131 for further information on auto switches. Type Special function Electrical entry Reed switch Solid state switch Grommet Connector Yes Grommet Yes Grommet Connector No Yes No Yes 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire -wire (NPN) 3-wire (NPN equivalent) 2-wire 2 V 2 V L L N Load voltage DC (Example) M9NW (Example) M9NWM (Example) M9NWL (Example) M9NWZ (Example) HCN V, V V V, V V V, V V V C V or less 2 V or less H H Manual release Non-locking type Lock position H Head end lock R Rod end lock N N M9W Rail mounting style Example and mounting style CDJ2-- CDJ2-- For rail mounting style, screws and nuts for 2 pcs switches come with the rail. Refer to page 3 for switch mounting brackets. For the applicable auto switch model, refer to the table below. If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. M9N FNV F9 M9P M9 HC M9NW FPV FV J9C FP J9 FNWV F9W M9PW M9W H HNF FWV FV FPW J9W F F9F 2 V 9 2 H 2H V 3 3H 93 9 C3C CC 3C C 9W H Since there are other applicable auto switches than listed, refer to page 3 for details. For details about auto switches with pre-wired connector, refer to pages 132 and and mounting style is not available for D-9V/M9V/M9WV and D-M9(V)L types. None N Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (However, when D-9/M9/M9W types are selected, only auto switch mounting brackets are assembled before being shipped.) When D-9(V)/M9(V)/M9W(V) types are mounted on a ø or ø rail, order auto switch mounting brackets separately. Refer to page 3 for details. 1 Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Indicator light Diagnostic indication (2-color indication) Grommet Lead wire length symbols:. m 1 m 3 m m Nil M L Z Wiring (Output) and mounting model Rail mounting Perpendicular In-line uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Lead wire length (m). 1 3 None Pre-wired pplicable load connector (Nil) (M) (L) (Z) (N) Relay, PLC Relay, PLC

73 ir Cylinder: With End Lock Series CJ2 Series CJ2 air cylinder is equipped with end lock function. Specifications ction Double acting, Single rod Fluid ir Proof pressure 1 MPa Maximum operating pressure. MPa Minimum operating pressure. MPa mbient and fluid temperature Without auto switch: C to C, With auto switch: C to C Cushion Rubber bumper Lubrication Not required (Non-lube) +1. length tolerance Piston speed to mm/s llowable kinetic energy.9 J No freezing. MPa for parts other than the lock unit. CJ1 CJP CJ2 CM2 CG1 Lock Specifications Lock position Holding force (Max.) Lock release pressure acklash Manual release Head end, Rod end 9 N. MPa or less 1 mm or less Non-locking type M M1 C2 CS1 Standard Standard stroke, 3,,,,,,, 1, 2 Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) CS2 Refer to pages 11 to 3 for cylinders with auto switches. Minimum stroke for auto switch mounting Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket part no. D- 111 Technical data

74 Series CJ2 Specific Product Precautions e sure to read before handling. Please consult with SMC for products outside these specifications. Use Recommended ir Pressure Circuit. Caution It is necessary for proper locking and unlocking. Operating Pressure Caution Supply air pressure of. MPa or higher to the port on the side that has the lock mechanism, as it is necessary for disengaging the lock. Exhaust ir Speed Caution The lock will engage automatically if the air pressure at the port on the side that has the lock mechanism becomes. MPa or less. e aware that if the piping on the side that has the lock mechanism is narrow and long, or if the speed controller is located far from the cylinder port, the exhaust air speed could become slower, involving a longer time for the lock to engage. similar result will ensure if the silencer that is installed on the exhaust port of the solenoid valve becomes clogged. 1 With head end lock Selection With rod end lock Caution 1. Do not use a 3 position solenoid valve. void using this cylinder in combination with a 3 position solenoid valve (particularly the closed center metal seal type). If air pressure becomes sealed inside the port on the side that contains the lock mechanism, the lock will not engage. Even if the lock is engaged at first, the air that leaks from the solenoid valve could enter the cylinder and cause the lock to disengage as time elapses. 2. ack pressure is necessary for unlocking. efore starting, make sure that air is supplied to the side that is not equipped with a lock mechanism as shown in the diagram above. Otherwise, the lock may not disengage. (Refer to Rock Disengagement.) 3. Disengage the lock before installing or adjusting the cyliner. The lock could become damaged if the cylinder is installed with its lock engaged.. Operate the cylinder at a load ratio of % or less. The lock might not disengage or might become damaged if a load ratio of % is exceeded.. Do not synchronize multiple cylinders. Do not operate two or more end lock cylinders synchronized to move a single workpiece because one of the cylinder locks may not be able to disengage when required.. Operate the speed controller under meter-out control. If operated under meter-in control, the lock might not disengage.. On the side that has a lock, make sure to operate at the stroke end of the cylinder. The lock might not engage or disengage if the piston of the cylinder has not reached the stroke end.. The position adjustment of the auto switch should be performed at two positions; a position determined by the stroke and a position after the backlash movement (by 1 mm). When a 2-color indication switch is adjusted to show green at the stroke end, the indication may turn red when the cylinder returns by the backlash. This, however, is not an error. Lock Disengagement Caution To disengage the lock, make sure to supply air pressure to the port on the side without a lock mechanism, thus preventing the load from being applied to the lock mechanism. (Refer to the recommended air pressure circuit.) If the lock is disengaged when the port on the side that does not contain a lock mechanism is in the exhausted state and the load is being applied to the lock mechanism, undue force will be applied to the lock mechanism, and it may damage the lock mechanism. lso, it could be extremely dangerous, because the piston rod could move suddenly. Manual Disengagement Caution Non-locking style manual release Insert the bolt, which is provided as an accessory part, through the rubber cap (it is not necessary to remove the rubber cap). Screw the bolt into the lock piston and pull the bolt to disengage the lock. Releasing the bolt will re-engage the lock. The bolt size, pulling force, and the stroke are listed below. Thread size M2. x. x 2l or more olt should be detached under normal operation, otherwise it may cause malfunction of the locking feature. Pulling force N.9 2 Rubber cap

75 ir Cylinder: With End Lock Series CJ2 Dimensions asic style With rod end lock: CJ2- -RN 2.3 ø ø h M x 1 Piping port 2 x M x. M x. CJ1 CJP CJ2 ø CM CG1 M M1 C2 CS1 CS2 With head end lock: CJ2- -HN ø ø h x M x 1 Piping port 2 x M x. M x. ø D- 113 Technical data

76 Series CJ2 Dimensions Flange style With rod end lock: CJ2F- -RN 33 2 Cover side (Head side) M x 1 M x x ø. Mounting hole With head end lock: CJ2F- Cover side (Rod side) 2 x M x 1 M x ø 2 -HN ø Piping port 2 x M x Piping port 2 x M x ø2 Cover outside diameter ø x ø. Mounting hole Cover outside diameter 11

77 ir Cylinder: With End Lock Series CJ2 xial foot style With rod end lock: CJ2L- -RN Cover side (Head side) M x 1 1. Piping port 2 x M x. CJ M x. 2.3 ø 2.3 ø CJP CJ2 CM CG1 2 x ø. Mounting hole M M1 C2 CS1 CS2 With head end lock: CJ2L- -HN Cover side (Rod side) 2 x M x 1 Piping port 2 x M x M x. ø ø x ø. Mounting hole + D- 1 Technical data

78 Series CJ2 Dimensions Double clevis style With rod end lock: CJ2D- -RN 2.3 ø2 M x. ø 1. Piping port 2 x M x øh9.3 Clevis pin (ød9.) ø

79 ir Cylinder Series CJ2 Proper uto Switch Mounting Position (Detection at stroke end) and Mounting Height Reed uto Switch <and mounting type> D-9 type Hs Solid State uto Switch <and mounting type> D-M9 type D-M9W type Hs 1 D-C/C type Hs 22 (2.) ( ): Values for D D-H type D-HW type D-HL type D-HNF type 1 CJ1 CJP CJ2 CM2 Hs CG1 D-C3C/CC type Hs D-HC type Hs M M1 C2 CS1 CS2 D- 11 Technical data

80 Series CJ2 Proper uto Switch Mounting Position (Detection at stroke end) and Mounting Height <Rail mounting type> D-9 type <Rail mounting type> D-M9 type D-M9W type Hs D-9V type (2) ( ): Values for D-93 Hs D-M9V type D-M9WV type Hs Hs D-/ type Hs D-H/H type Lead wire min. bending radius Hs D-F/J9 type D-FW/J9W type D-F9F/FL type Hs Hs D-FV/FWV type D-FVL type D-3C/C type Lead wire min. bending radius D-J9C type D-9W type Lead wire min. bending radius For the direct mount type, the relation between the auto switch mounting position and the port position is as shown below. Port Hs Hs Hs Hs

81 ir Cylinder Series CJ2 Proper uto Switch Mounting Position (Detection at stroke end) and Mounting Height Proper uto Switch Mounting Position (Single acting type excluded) model model 1. () 2 2. D-9 D-9 D-9V 1. () (). D-M9 D-M9W and mounting. (). D-M9 D-M9V D-M9W D-M9WV D-M9L D-M9VL 2 (.) 2. 3 D-C D-C D-C3C D-CC D- D- 2 (.) 2. 3 D-H D-HC D-HNF D-HW D-HL 1 (.) 1. 2 Rail mounting 1 () 1. 2 D-H/H D-3C/C D-F/J9 D-FW/J9W D-FV/FWV D-F9F D-J9C D-FL D-FVL D-FNTL D-9W CJ1 CJP CJ2 CM2 CG1 M M Figures in parentheses for bore ø are for the double rod type (Series CJ2W). In the actual setting, adjust them after confirming the auto switch performance C2 CS1 CS2 uto Switch Mounting Height model D-9 D-M9 D-M9W D-C/C D-H/HW D-HNF D-HL and mounting D-C3C D-CC D-HC D- D- Hs Hs 1 2. Hs Hs Hs. 19. model D-9 D-9V D-M9 D-M9V D-M9W D-M9WV D-M9L D-M9VL D-H/H D-F/J9 D-FW/J9W D-FL/F9F D-FNTL D-3C D-C Rail mounting D-FV D-FWV D-FVL D-J9C D-9W Hs Hs Hs Hs 2 23 Hs 23 2 Hs D- 119 Technical data

82 Series CJ2 Proper uto Switch Mounting Position (Detection at stroke end) and Mounting Height Single cting, Spring Return Type (S) Proper auto switch mounting position: Spring return type (S) Standard type (CDJ2-S) Non-rotating rod type (CDJ2K-S) Direct mount type (CDJ2R-S) Non-rotating rod/direct mount type (CDJ2RK-S) model to st to 3 st 31 to st to st Dimensions 1 to st to st 1 to st to st D and mounting D-M9 D-M9W D-C/C D-C3C D-CC D-H/HC D-HW/HL D-HNF D-9 D-9V D-M9/M9V D-M9W/M9WV D-M9L/M9VL Rail mounting D-/ D-H/H D-3C/C D-F/J9 D-FW/J9W D-FV/FWV D-F9F/J9C D-FL D-FVL D-FNTL D-9W In the actual setting, adjust them after confirming the auto switch performance.

83 ir Cylinder Series CJ2 Proper uto Switch Mounting Position (Detection at stroke end) and Mounting Height Single cting, Spring Extend Type (T) Proper auto switch mounting position: Spring extend type (T) Standard type (CDJ2-T) Non-rotating rod type (CDJ2K-T) Direct mount type (CDJ2R-T) Non-rotating rod/direct mount type (CDJ2RK-T) and mounting model D-9 D-M9 D-M9W D-C/C D-C3C D-CC D-H/HC D-HW/HL D-HNF D-9 D-9V D-M9/M9V D-M9W/M9WV D-M9L/M9VL to st to 3 st to st Dimensions to st to st.. 9 to st to st to st CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 Rail mounting D-/ D-H/H D-3C/C D-F/J9 D-FW/J9W D-FV/FWV D-F9F/J9C D-FL D-FVL CS2 D-FNTL D-9W In the actual setting, adjust them after confirming the auto switch performance. D- Technical data 1

84 Series CJ2 Minimum uto Switch Mounting mounting and mounting Rail mounting model D-9 D-M9 D-M9W D-C D-C D-H/HW D-HL D-HNF D-C3C D-CC D-HC D-M9V D-9V D-M9 D-9 D-M9WV D-M9VL D-M9W D-M9L D-/ D-H/H D-3C/C D-H D-H D-9W D-F D-J9 D-FV D-J9C D-FW/J9W D-FL/F9F D-FNTL D-FWV D-FVL No. of auto switch mounted 2 pcs. n pcs. (n: No. of auto switch) 1 pc. Different surfaces Same surface Different surfaces Same surface (n-2) + 3 Note) Note) 2 + (n-2) (n = 2,, ) (n-2) (n-2) (n = 2,, ) (n-2) (n-2) (n = 2,, ) (n-2) (n-2) (n = 2,, ) + (n-2) (n =, ) 2 + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) 2 + (n-2) (n =, ) 2 + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) + 2 (n-2) (n =, ) + (n-2) (n =, ) Different surfaces With 2 auto switches Same surface. -. model D-93 D-M9 D-M9W D-M9 D-M9W The proper auto switch mounting position is. mm inward from the switch holder edge. Less than 2 strokes Note) When 2 D-93/M9/M9W auto switches are included.. -. The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. Less than strokes Less than strokes 2

85 ir Cylinder Series CJ2 Operating range and mounting Rail mounting model D-9 D-M9 D-M9W D-C/C/C3C/CC D-H/HW D-HL/HNF D-HC D-9/9V D-M9/M9V D-M9W/M9WV D-M9L/M9LV D-//H/H D-3C/C D-9W D-F/J9/FW/J9W D-FV/FWV/F9F D-J9C/FL/FVL D-FNTL Since this is a guideline including hysteresis, not meant to be guaranteed. (ssuming approximately ±3% dispersion.) There may be the case it will vary substantially depending on an ambient environment uto Switch Mounting racket: Part No. mounting and mounting Rail mounting model D-9 D-M9 D-M9W D-C/C D-C3C/CC D-H/HW D-HL/HNF D-9 D-9V D-M9 D-M9V D-M9W D-M9WV D-M9L () D-M9VL () ø ø ø Note 1), Note 2) J2- J3-1 d Switch holder (Resin) c Switch bracket (Stainless steel) J2- Note 1), Note 2) J2- J3-1 J2- Note 3), Note ) Q2-, Q2-S Q2- Q2-S Note 1), Note 2) J2- J3-1 e Switch spacer (Stainless steel) Set screw (Not used) b mounting screw a mounting band J2-: set of a and b above J3-1: set of c, d and e above J2- Note 3), Note ) Q2-, Q2-S CJ1 CJP CJ2 CM2 CG1 M M1 C2 CS1 CS2 Note 1) Two kinds of auto switch bracket are used as a set. Note 2) When cylinders are shipped, only auto switch mounting brackets are assembled. Note 3) When a compact auto switch is mounted on a ø or ø rail, an auto switch bracket is needed, to be ordered separately. CDJ2-- 1 D-M9WV 2 pcs. Q2-2 pcs. Note ) For D-M9(V)L, order Q2-S, which uses stainless steel mounting screws. [Stainless Steel Mounting Screw Kit] The following set of stainless steel mounting screws is available. Use them in accordance with the operating environment. (Since auto switch brackets are not included, order them separately.) : For D-C/C/H types Note ) Refer to page 13 for the details of screws. The above stainless steel screws are used when a cylinder is shipped with D-HL-type auto switches. When only a switch is shipped independently, screws are attached. Reference mounting brackets using stainless steel screws are available for stainless steel cylinder CJ. uto Switch Mounting rackets for CJ: Part No. mounting bracket part no. Note J2-S J2-S Stainless steel mounting screw In addition to the auto switches listed above, the following auto switches are also available. Refer to pages 3 to 131 for the detailed specifications. type Part no. Electrical entry (Entry direction) Features D-C3, C Reed D-C Without light Grommet (In-line) D-H1, H2, H Sold state D-HNW, HPW, HW Diagnosis indication (2 colors) Solid state auto switches are also available with a pre-wired connector. Refer to pages 132 and 1329 for details. Normally closed (NC = b contact) solid state auto switches (D-F9G/F9H types) are also available. Refer to page 9 for details. 3 D- Technical data

86 Low Speed Cylinder Double cting, Single Rod Series CJ2X ø, ø How to Order L F D Mounting style asic style xial foot style Rod side flange style Double clevis style CJ2X mm mm L CDJ2X L With auto switch Standard stroke ø, 3,,,,,, ø, 3,,,,,,, 1, 2 Intermediate stroke other than above is manufactured upon receipt of order. uilt-in Magnet Cylinder Model Suffix the symbol - (Rail mounting style) or - (and mounting style) to the end of part number for cylinder with auto switch. Example Rail mounting style and mounting style CDJ2X-- CDJ2X-- For the rail mounting type, screws and nuts for two auto switches are included in the rail. M9W With auto switch (uilt-in magnet) Low speed cylinder Port location on head cover Symbol Nil R ø, ø Perpendicular to axis xial direction Nil Without auto switch For the applicable auto switch model, refer to the table below. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. For configuration, refer to page 11. pplicable uto Switch/Refer to pages 119 to for further information on auto switches. Type Reed switch Solid state switch Special function Diagnostic indication (2-color indication) With diagnostic output (2-color indication) Diagnostic indication (2-color indication) Electrical entry Grommet 2-wire Connector Yes 2 V 3-wire (NPN) Grommet Grommet Yes Connector Grommet No Yes No Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 3-wire (PNP) 2-wire -wire (NPN) 3-wire (NPN equivalent) 2-wire 2 V Load voltage DC V, V V V, V V V, V V Lead wire length symbols:. m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL m Z (Example) M9NWZ Indicator light C 2 V V V V or less 2 V or less and mounting M9N M9P M9 HC M9NW M9PW M9W HNF C3C CC model Rail mounting Perpendicular In-line FNV FPV FV J9C FNWV FWV 2 3 3C C 9W F9 FP J9 F9W FPW J9W F9F H 2H 3H H Lead wire length (m). (Nil) 1 (M) 3 (L) (Z) None (N) Pre-wired connector pplicable load Since there are other applicable auto switches than listed, refer to page 13 for details. For details about auto switches with pre-wired connector, refer to pages 1 and 1. For the band mounting type, D-9V/M9V/M9WV/M9(V)L types cannot be mounted. Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W///F/J auto switches are shipped together (not assembled). (When D-9/M9/M9W are specified, only auto switch mounting brackets are assembled before shipped.) D-C/C/H auto switches are assembled at the time of shipment. Order auto switch mounting brackets separately when D-9(V)/M9(V)/M9W(V) types are mounted with a rail. Refer to page 13 for details. 111 Relay, PLC Relay, PLC

87 Low Speed Cylinder Double cting, Single Rod Series CJ2X Specifications JIS Symbol Double acting, Single rod Precautions e sure to read before handling. Refer to front matters 2 and 3 for Safety Instructions and pages 3 to 11 for ctuator and uto Switch Precautions. Mounting Caution 1. During installation, secure the rod cover and tighten by applying an appropriate tightening force to the retaining but or to the rod cover body. If the head cover is secured or the head cover is tightened, the cover could rotate, leading to the deviation. 2. Proper tightening torque for mounting thread should be within the range specified. pply a Loctite (no. 22 lue) for mounting thread. Proper tightening torque for mounting thread (N m) (tightening torque for mounting nut) 3. to 3.2. to.9 3. To remove and install the retaining ring for the knuckle pin or the clevis pin, use an appropriate pair of pliers (tool for installing a type C retaining ring). Especially with ø, use ultra thin pliers, such as Super Tool Corp., CSM-.. For the auto switch mounting rail, do not remove the pre-equipped rail. Since the mounting thread is drilled through inside a the cylinder, it will result in air leakage. Operating Precautions Warning 1. It might not be able to control by meter-out at a low speed operation. Caution 1. For Series CJ2X,.1 Nl/min is the values at maximum in terms of its construction and there is internal leakage (NR). ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Cushion Lubrication length tolerance Piston speed Double acting, Single rod ir 1. MPa. MPa. MPa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Rubber bumper (Standard equipment) Not required (Non-lube) to 3 mm/s llowable kinetic energy ø.3 J ø.9 J Standard Mounting Style and ccessory Port Location on Head Cover Mounting racket Part No. Standard stroke, 3,,,,,,, 3,,,,,,, 1, 2 Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Standard equipment Option Mounting Mounting nut Clevis pin Single knuckle joint Double knuckle joint asic style T-bracket Pin and retaining ring are shipped together with double clevis and double knuckle joint. Mounting bracket Foot bracket Flange bracket T-bracket CJ-L CJ-F CJ-T T-bracket is used with double clevis (D). CJ-L CJ-F CJ-T xial foot style Rod side flange style Double clevis style For basic style, the port position in a head cover is available either perpendicular to the axis or in-line with the cylinder axis. xial direction Perpendicular 11 RE RE REC CY CX MQ RHC RZQ D-

88 Series CJ2X asic Style () CJ2X Port location on head cover Mounting nut CJ2X, Piping port 2 x M x. Piping port M x. Port location on head cover: xial location (R) xial Foot Style (L) CJ2XL CJ2XL, Z + For details of the mounting nut, refer to page C 1 2 D F G G H 2 2 MM M x. M x. N.. N NDh NN M x 1. M x 1. S T Z Port location on head cover Cover surface Mounting nut Piping port 2 x M x. Piping port M x. Z + Port location on head cover: xial location (R) For details of the mounting nut, refer to page C 1 2 D F G G H 2 2 L 23 LC.. LH 9 1 LT LX 2 33 LY. 2 LZ 32 2 MM M x. M x. N.. N NN M x 1. M x 1. S T X Y 9 Z 11

89 Low Speed Cylinder Double cting, Single Rod Series CJ2X Rod Side Flange Style (F) CJ2XF Port location on head cover CJ2XF, Cover surface Mounting nut Piping port 2 x M x. Piping port M x. -.3 Mounting hole Z + Port location on head cover: xial location (R) 1.3 C 1 2 D F F For details of the mounting nut, refer to page 111. FC.. FT FX 2 33 FY 1 2 FZ 32 2 G G H 2 2 MM M x. M x. N.. N NN M x 1. M x 1. S T Z Double Clevis Style (D) CJ2XD Z + Piping port 2 x M x. Clevis pin -.3 T-bracket CZ -.3 For details, refer to page 111. RE ZZ + RE Clevis pin and retaining ring are shipped together. 1.3 T-bracket Dimensions TC.. TH 29 3 C 1 2 TV CD (cd) 3.3 TW 22 2 CX 3.2. TX 32 3 CZ 1.3 TY D G G 1 23 H 2 2 MM M x. M x. N.. N R S U Z 2 ZZ REC CY CX MQ RHC RZQ D- 111

90 Series CJ2X ccessory racket Dimensions Single Knuckle Joint Clevis Pin Knuckle Pin pplicable Part no. 1 bore L1 MM ND H NX R1 I-J 21 M x I-J 2 +. M x..3. Material: Rolled steel Material: Stainless steel Material: Stainless steel U1 9 1 pplicable pplicable Part no. Dd9 d L l m t bore retaining ring CD-J Type C CD-Z Type C Retaining rings are packaged with clevis pins. pplicable Part no. bore Dd9 CD-J IY-J For size ø, clevis pin is diverted. Retaining rings are packaged with knuckle pins. d L l m Type C Type C t pplicable retaining ring Double Knuckle Joint Mounting Nut Rod End Nut hole axis Material: Rolled steel Part no. Y-J Y-J pplicable bore 1 11 L.2. L MM M x. M x. Part no. NDd9 NDH NX R1 U1 Y-J Y-J Knuckle pin and retaining ring are shipped together. pplicable Part no. bore SNJ- SNJ C..2 Material: rass d H M x 1. M x 1. Part no. NTJ- NTJ- pplicable bore C Material: Iron d H M x. 3.2 M x. T-bracket Rod End Cap Double clevis style cylinder x øtc Flat type/cj-cf Round type/cj-cr Part no. pplicable bore TC TDH TH TK TN TT TU TV TW TX TY TZ +. CJ-T CJ-T T-bracket includes a T-bracket base, single knuckle joint, hexagon socket head cap screw and spring washer. Part no. Flat type Round type CJ-CF CJ-CR CJ-CF CJ-CR pplicable bore D L 13 Material: Polyacetal MM M x. M x. N R W 111

91 Low Speed Cylinder Double cting, Single Rod Series CJ2X uto Switch Proper Mounting Position (Detection at End) and Its Mounting Height Reed auto switch <and mounting style> Solid state auto switch <and mounting style> D-9 D-M9 D-M9W Hs Hs (2.) ( ): For D-93 type D-C/C Hs D-H D-HW D-HNF Hs D-C3C/CC D-HC Hs Hs RE RE REC CY CX MQ RHC RZQ D- 1119

92 Series CJ2X uto Switch Proper Mounting Position (Detection at End) and Its Mounting Height Reed auto switch <and mounting style> Solid state auto switch <and mounting style> D-9 D-M9 D-M9W Hs (2) ( ): For D-93 type Hs D-9V D-M9V D-M9WV Hs D-/ D-F/J9 D-FW/J9W D-F9F Hs D-H/H Minimum lead wire bending radius Hs Minimum lead wire bending radius D-3C/C Hs D-9W Hs Hs Hs 21. Hs Hs D-FV/FWV D-J9C Minimum lead wire bending radius 1

93 Low Speed Cylinder Double cting, Single Rod Series CJ2X uto Switch Proper Mounting Position (Detection at End) and Its Mounting Height uto Switch Proper Mounting Position model ore size D and mounting D-M9 D-M9W. D-C D-C D-C3C D-CC D-H D-HC D-HNF D-HW D-9 D-9V D-M9 D-M9V D-M9W D-M9WV.. D- D Rail mounting 3 3. D-H/H D-3C/C D-F/J9 D-FW/J9W D-FV/FWV D-F9F D-J9C D-FNTL D-9W Note) djust the auto switch after confirming the operating conditions in the actual setting. uto Switch Mounting Height model ore size D-9 D-M9 D-M9W Hs. 2 and mounting D-C D-C D-H D-HW D-HNF Hs 1 2. D-C3C D-CC Hs D-HC Hs D- D- Hs. 19. D-9 D-9V D-M9 D-M9V D-M9W D-M9WV Hs D-H/H D-F/J9 D-FW/J9W D-F9F D-FNTL Hs Rail mounting D-3C D-C Hs D-FV D-FWV Hs 2 23 D-J9C Hs 23 2 D-9W Hs RE RE REC CY CX MQ RHC RZQ D- 11

94 Series CJ2X Minimum uto Switch Mounting mounting and mounting Rail mounting model D-9 D-M9 D-M9W D-C D-C D-H/HW D-HNF D-C3C D-CC D-HC D-M9V D-9V D-M9 D-9 D-M9WV D-M9W D-/ D-H/H D-3C/C D-H D-H D-9W D-F D-J9 D-FV D-J9C D-FW/J9W D-F9F D-FNTL D-FWV No. of auto switch mounted 2 pcs. n pcs. (n: No. of auto switch) 1 pc. Different surfaces Same surface Different surfaces Same surface (n-2) Note) Note) (n-2) (n = 2,, ) (n-2) (n-2) (n = 2,, ) (n-2) (n-2) (n = 2,, ) (n-2) (n-2) (n = 2,, ) + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) 2 + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) + (n-2) (n =, ) + 2 (n-2) (n =, ) + (n-2) (n =, ) Note) When 2 D-93/M9/M9W auto switches are included. Different surfaces With 2 auto switches Same surface. -. model D-93 D-M9 D-M9W D-M9 D-M9W The proper auto switch mounting position is. mm inward from the switch holder edge. Less than 2 strokes. -. The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. Less than strokes Less than strokes 12

95 Low Speed Cylinder Double cting, Single Rod Series CJ2X Operating Range uto Switch Mounting racket/part No. and mounting Rail mounting D-9 model D-M9 D-M9W D-C/C/C3C/CC D-H/HW D-HNF D-HC D-9/9V D-M9/M9V D-M9W/M9WV D-//H/H D-3C/C D-9W D-F/J9/FW/J9W D-FV/FWV/F9F D-J9C D-FNTL Since this is a guideline including hysteresis, not meant to be guaranteed. (ssuming approximately ±3% dispersion.) There may be the case it will vary substantially depending on an ambient environment. mounting and mounting model D-9 D-M9 D-M9W D-C/C D-C3C/CC D-H/HW D-HNF ø Note 1), Note 2) qj2- wj3-1 d Switch holder (Resin) c Switch bracket (Stainless steel) J2- Note 3) Q2- ø Note 1), Note 2) qj2- wj3-1 e Switch spacer (Stainless steel) Set screw (not used) b mounting screw a mounting band qj2-: set of a and b in the figure. wj3-1: set of c, d and e in the figure. J2- Note 3) Q2- Rail mounting D-9 D-9V D-M9 D-M9V D-M9W D-M9WV Q2- Note 1) Two kinds of auto switch mounting brackets are used as a set. Note 2) mounting brackets are shipped together with cylinders. Note 3) When mounting a compact auto switch on the ø or ø rail mounting type, order auto switch mounting bracket shown in the table above. Order it separately from the cylinder. Example CDJ2X-- 1 unit D-M9WV 2 pcs. Q2-2 pcs. RE RE REC Other than the applicable auto switches listed in How to Order, the following auto switches can be mounted. For detailed specifications, refer to pages 119 to. type Model Electrical entry (Direction) Features D-C3, C Reed D-C Without indicator light Grommet (in-line) D-H1, H2, H Solid state D-HNW, HPW, HW Diagnostic indication (2-color indication) With pre-wired connector is available for solid state auto switches. For details, refer to pages 1 to 1. Normally closed (NC = b contact), solid state auto switches (D-F9G, F9H type) are also available. For details, refer to page CY CX MQ RHC RZQ D- 13

96 Elbow/Universal Type Related Products: Speed Controller for Low Speed Operation The effective area of controlled flow is approximately 1/ of the standard type. These controllers are suitable for controlling the speed of microspeed cylinders. The dual type speed controller is especially suitable for cylinders with a small bore size. ir Flow/Effective rea Model S1FM-M S131FM-M Tubing Metric size ø3.2, ø, ø O.D. ø1/", ø/32", ø3/" Inch size ø1/" Controlled ir flow (l/min (NR)) flow Effective area (mm 2 ).1 Free flow Flow rate (l/min (NR)) Effective area (mm 2 ) 1. Note) Supply pressure:. MPa, Temperature: 2 C S221FM-1 S231FM-1 ø3.2, ø ø3/", ø1/" ø1/", ø/32" ø/" ø, ø S221FM-2 S231FM-2 ø ø/32" 2 ø ø, ø ø1/", ø/" ø3/" ø3/" In-line Type ir Flow/Effective rea Model S1FM Tubing Metric size ø3.2, ø, ø O.D. ø1/", ø/32", ø3/" Inch size ø1/" Controlled flow ir flow (l/min (NR)) Effective area (mm 2 ).1 Free flow Flow rate (l/min (NR)) Effective area (mm 2 ) 1. Note) Supply pressure:. MPa, Temperature: 2 C S21FM ø ø ø/32" ø3/", ø1/" S21FM ø ø ø3/" ø1/", ø/" Elbow Type (Metal body) Dual Type ir Flow/Effective rea Model SM S22M-1 S22M-2 Port size Cylinder side R 1/ R 1/ M x. -32 UNF NPT 1/ Tube side Rc 1/ Rc 1/ NPT 1/ Controlled flow Free flow ir flow (l/min (NR)) Flow rate (l/min (NR)) Effective area (mm 2 ) Effective area (mm 2 ) Note) Supply pressure:. MPa, Temperature: 2 C ir Flow/Effective rea Model Metric size Tubing O.D. Inch size Controlled flow ir flow (l/min (NR)) (Free flow) Effective area (mm 2 ) Note) Supply pressure:. MPa, Temperature: 2 C SD23FM-M SD33FM-1 SD3FM-2 ø, ø ø, ø ø ø, ø ø1/", ø/32" ø3/", ø1/".1 ø3/", ø1/" 3.2 ø1/", ø/" ø3/". RE RE REC CY CX MQ RHC RZQ D-

97 Low Speed Cylinder Specific Product Precautions e sure to read before handling. Refer to front matters 2 and 3 for Safety Instructions and pages 3 to 11 for ctuator and uto Switch Precautions. Warning Horizontal Operation 1 Recommended Pneumatic Circuit 11 Dual speed controller Speed is controlled by meter-out circuit. Using concurrently the meter-in circuit can alleviate the stick-slip. More stable low speed operation can be achieved than meter-in circuit alone. Vertical Operation 1 W 11 P1 Meter-in speed controller Meter-in speed controllers can reduce lurching while controlling the speed. The two adjustment needles facilitate adjustment. a P2 (c) (b) P a P W (1) Speed is controlled by meter-out circuit. Using concurrently the meter-in circuit can alleviate the stick-slip. (2) Depending on the size of the load, installing a regulator with check valve at position (b) can deduce lurching during descent and operation delay during ascent. s a guide, when W + Pa>P, adjust P1 to make W + P1a = P. (1) Speed is controlled by meter-out circuit. Using concurrently the meter-in circuit can alleviate the stick-slip. (2) Installing a regulator with check valve at position (c) can reduce lurching during descent and operation delay during ascent. s a guide, adjust P2 to make W + P2 = Pa. W: Load (N) P: Operating pressure (MPa) P1, P2: Reduced pressure (MPa) a: Rod side piston area (mm 2 ) : Head side piston area (mm 2 ) Warning Since CJ2X, CUX are subject to internal leakage due to their construction, the speed may not be fully controlled with the meter-out controller ( ) during low speed operation. Caution Selection 1. Operate within the standard strokes. Operating with the stroke exceeding the standard stroke may cause malfunction. 2. Provide a construction that does not apply a lateral load to the cylinder. pplying a lateral load to the cylinder may cause malfunction. 3. Do not use the product at a high frequency. Use it at 3 cpm or less as a guideline.. Do not wipe out the grease in the sliding part of the air cylinder. Doing so forcefully may cause malfunction. Caution Pneumatic Circuit 1. The piping length between the speed controller and the cylinder port must be kept as short as possible. If the speed controller and the cylinder port are far apart, speed adjustment may be unstable. 2. Use a low speed controller to easily adjust for low speed operation or a dual speed controller (Series SD) to prevent cylinders from popping out. (When the low speed controller is used, the maximum speed may be limited.) 1

98 Fine Lock Cylinders/Lock-up Cylinder Series CL ø, ø2, ø2, ø32, ø, ø, ø3, ø, ø, ø, ø1, ø Locking method Features Spring locking Unlocking Discharging the air causes the lock to operate. (Lock-up cylinders are spring locking only.) Pneumatic locking Pressure locking The holding power can be varied according to the air pressure that is applied to the port. Spring and pneumatic locking Pressure locking The holding power can be varied according to the air pressure that is applied to the port. Unlocking Discharging the air causes the lock to operate. Locking in both directions is possible. Locking in either side of cylinder stroke is possible, too. (The lock-up cylinder can be locked only in one direction.) CLJ2 CLM2 CLG1 CL1 MLGC CNG MN CN CNS Series Variations Series Fine lock cylinders Series CLJ2 ction Double acting Rod Single rod Standard variations built-in magnet With rod boot Locking direction oth directions Spring locking Locking method Pneumatic locking Spring and Pneumatic locking Standard stroke to 2 Page 1 CLS CLQ RLQ MLU MLGP ML1C Series CLM2 Double acting Single rod oth directions to 3 11 Series CLG1 2 2 to 2 Double acting Single rod oth directions to 3 2 Lock-up cylinder Series CL1 Double acting Single rod One direction, 3,, 1 2 to 2 to 2 to Up to Up to 3 D- 9

99 Series CL Specific Product Precautions 1 e sure to read before handling. The precautions on these pages are for the fine lock cylinders and the lock-up cylinders. For general actuator precautions, refer to ctuator Precautions on pages 3 to. Design of Equipment and Machinery Warning 1. Construct so that the human body will not come into direct contact with driven objects or the moving parts of locking cylinders. If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration. If the lock is applied at a desired position of a stroke and compressed air is applied to only one side of the cylinder, the piston will lurch at a high speed the moment the lock is disengaged. In such a situation, there is a risk of injury to humans, or equipment damage. To prevent the piston from lurching, use a balance circuit such as the recommended pneumatic circuit (P. 9). If an air-hydro fine lock cylinder is used, make sure to operate the lock portion through air pressure. Never use oil on the lock-up cylinder because the lock-up cylinder is a non-lube style. Failure to observe this could cause the lock to malfunction. Warning Selection Refer to the following criteria for the maximum load in the locked state, and set. When a cylinder is in a no-load and locked state, the holding force (maximum static load) is the lock s ability to hold a static load that does not involve vibrations or shocks. To ensure braking force, the maximum load must be set as described below. 1. For constant static loads, such as for drop prevention: Fine lock series (Series CLJ2/CLM2/ CLG1) 3% or less of the holding force (maximum static load) Note) For applications such as drop prevention, consider situations in which the air source is shut off, and make selections based on the holding force of the spring locked state. Do not use the pneumatic lock for drop prevention purposes. Lock-up series (Series CL1) % or less of the holding force (maximum static load) 2. When kinetic energy acts upon the cylinder, such as when effecting an intermediate stop, there are constraints in terms of the allowable kinetic energy that can be applied to the cylinder in a locked state. Therefore, refer to the allowable kinetic energy of the respective series. Furthermore, during locking, the mechanism must sustain the thrust of the cylinder itself, in addition to absorbing the kinetic energy. Therefore, even within a given allowable kinetic energy level, there is an upper limit to the amount of the load that can be sustained. Fine lock series (Series CLJ2/CLM2/ CLG1) Maximum load at horizontal mounting: % or less of the holding force (Maximum static load) for spring lock Maximum load at vertical mounting: 3% or less of the holding force (Maximum static load) for spring lock Lock-up series (Series CL1) Maximum load at horizontal mounting: % or less of the holding force (Maximum static load) Maximum load at vertical mounting: 2% or less of the holding force (Maximum static load) 3. In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit.. The locking of the fine lock cylinder is directional. lthough the fine lock cylinder can be locked in both directions, be aware that its holding force is smaller in one of the directions. CLJ2/CLM2/CLG1 Holding force at piston rod extended side decreases approx. %.. The locking of the lock-up cylinder is unidirectional. ecause the locking direction of the lock-up cylinder is unidirectional, select the locking direction in accordance with the particular operating conditions. It is also possible to manufacture a bidirectional lock-up cylinder. For details, refer to Made to Order on page 199. Due to the nature of its construction, a lock-up cylinder has a play of approximately. mm to 1 mm in the axial direction. Therefore, if an external stopper is used to stop the piston rod and the lock is engaged, the piston rod will shift in the amount of its axial play.. To effect an intermediate stop, take the cylinder s stopping precision and overrun amount into consideration. ecause the lock is applied by mechanical means, the piston will not stop immediately in response to a stopping signal, but only after a time lag. This lag determines the amount of the overrun of the piston stroke. Thus, the range of the maximum and minimum amounts of the overrun is the stopping precision. Place the limit switch before the desired stopping position, only in the amount of the overrun. The limit switch must have a detection length (dog length) of the overrun amount + α. For SMC s auto switches, the operating range are between and 1 mm. (It varies depending on a switch model.) When the overrun amount exceeds this range, self-holding of the contact should be performed at the switch load side. For stopping accuracy, refer to Series CLJ (P. 3), Series CLM2 (P. 1), Series CLG1 (P. 2), and Series CL1 (P. 3) respectively. Stop signal Overrun amount. In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder.. e aware that the stopping accuracy is influenced by changes in the piston speed. The variance in the stopping position increases if the piston speed changes, such as due to load fluctuations during the reciprocal movement of the piston. Therefore, take measures to ensure a constant piston speed immediately preceding the stopping position. Furthermore, the variances in the stopping position increases when the piston is effecting a cushioning stroke or during acceleration after starting its movement. 9. When unlocking is performed, if the thrust is applied to the piston, unlocking will not be easily done. To avoid that, ensure that unlocking should be performed before the thrust is applied to the piston. 9

100 Series CL Specific Product Precautions 2 e sure to read before handling. The precautions on these pages are for the fine lock cylinders and the lock-up cylinders. For general actuator precautions, refer to ctuator Precautions on pages 3 to. Warning Caution Mounting 1. e certain to connect the rod end to the load with the lock released. If this is performed with the lock engaged, a load that exceeds the allowable rotational force or holding force would be applied to the piston rod, which could damage the locking mechanism. The fine lock and Series CL1 with ø to ø cylinders have a built-in manual unlocking mechanism. Therefore, they can be maintained in the unlocked state without supplying air. For Series CL1 with ø to ø cylinders, simply connect piping to the lock-up port, and supply air pressure of.2 MPa or more to disengage the lock in order to attach a load. 1. Do not apply offset loads on the piston rod. Pay particular attention to aligning the center of gravity of the load with the axial center of the cylinder. If there is a large amount of deviation, the piston rod could become unevenly worn or damaged due to the inertial moment that is created when the piston rod is stopped by the lock. X Load center of gravity and cylinder shaft center are not matched. Caution djustment 1. Place it in the locked position. (Excluding the series CL1 ø to ø.) The locks are manually disengaged at the time the cylinders are shipped from the factory. Therefore, make sure to change them to the locked state before using the cylinders. For procedures to effect the change, refer to page 99 for the fine lock series. e aware that the lock will not operate properly if the change is not performed correctly. djust the cylinder's air balance. In the state in which a load is attached to the cylinder, disengage the lock and adjust the air pressure at the rod side and the head side of the cylinder to obtain a load balance. y maintaining a proper air balance, the piston rod can be prevented from lurching when the lock is disengaged. 2. djust the mounting position of detections such as those of the auto switches. To effect an intermediate stop, adjust the mounting position of the auto switch detection by taking the amount of overrun into consideration in relation to the desired stopping position. CLJ2 CLM2 CLG1 CL1 MLGC CNG MN CN CNS CLS CLQ RLQ MLU MLGP ML1C Load center of gravity and cylinder shaft center are matched. Note) Can be used if all of the generated moment is absorbed by an effective guide. D- 9

101 Series CL Specific Product Precautions 3 e sure to read before handling. The precautions on these pages are for the fine lock cylinders and the lock-up cylinders. For general actuator precautions, refer to ctuator Precautions on pages 3 to. W Warning 1. e certain to use an pneumatic circuit which will apply balancing pressure to both sides of the piston when in a locked stop. In order to prevent cylinder lurching after a lock stop, when restarting or when manually unlocking, a circuit should be used to which will apply balancing pressure to both sides of the piston, thereby canceling the force generated by the load in the direction of piston movement. 2.Use a solenoid valve for unlocking which has a large effective area, as a rule % or more of the effective area of the cylinder drive solenoid valve. The larger the effective area is, the shorter the locking time will be (the overrun amount will be shorter), and stopping accuracy will be improved. 3. Place the solenoid valve for unlocking close to the cylinder, and no farther than the cylinder drive solenoid valve. The shorter the distance from the cylinder (the shorter the piping), the shorter the overrun amount will be, and stopping accuracy will be improved.. llow at least. seconds from a locked stop (intermediate stop of the cylinder) until release of the lock. When the locked stop time is too short, the piston rod (and load) may lurch at a speed greater than the control speed of the speed controller.. When restarting, control the switching signal for the unlocking solenoid valve so that it acts before or at the same time as the cylinder drive solenoid valve. If the signal is delayed, the piston rod (and load) may lurch at a speed greater than the control speed of the speed controller.. asic circuit 1) [Horizontal] Forward ackward 3 port normally closed SOL. SOL.C 2) [Vertical] Load in the direction of rod extension Regulator with check valve Pressure center SOL. SOL. ON OFF ON ON ON OFF ON ON SOL. ON OFF OFF ON OFF OFF OFF OFF SOL.C OFF OFF OFF OFF ON OFF OFF ON ction Forward Locked stop Unlocked Forward ackward Locked stop Unlocked ackward Pneumatic Circuit. s or more to. s. s or more to. s Load in the direction of rod retraction W SOL.C Caution 1. 3 position pressure center solenoid valve and regulator with check valve can be replaced with two 3 port normally open valves and a regulator with relief function. [Example] 1) [Horizontal] W SOL. SOL. 3 port normally closed SOL. Cylinder side 2) [Vertical] Load in the direction of rod extension SOL. W 3 port normally open SOL.C SOL. Cylinder side Regulator with relief function Load in the direction of rod retraction SOL. SOL.C W SOL. SOL.C SOL. W SOL. SOL.C SOL. 9

102 Series CL Specific Product Precautions e sure to read before handling. The precautions on these pages are for the fine lock cylinders and the lock-up cylinders. For general actuator precautions, refer to ctuator Precautions on pages 3 to. How to Manually Disengage the Lock and Change from the Unlocked to the Locked State The lock is manually disengaged at the time the cylinder is shipped from the factory. ecause the lock will not operate in this state, make sure to change it to the locked state before operation, after having adjusted the axial center for installation. How to Change from Unlocked to Locked State 1. Series CLJ2, CLM2, CLG1 1) Loose locking nut. 2) Turn the wrench flats section of the manual unlocking cam to the LOCK position that is marked on the cam guide. 3) While keeping the wrench flats section in place, tighten the lock nut. Note) The manual unlocking cam will rotate approximately 1. Do not rotate the wrench flats section excessively. Locked state Manual unlocking cam Lock nut Cam guide rake arm rake piston FREE rake spring Manually unlocked state LOCK and FREE are marked on the cam guide. Manually Unlocking The lock of a fine lock series cylinder can be disengaged manually through the procedure described below. However, make sure to disengage the lock pneumatically before operating the cylinder. Note) Manual disengagement of the lock could create a greater cylinder sliding resistance than pneumatic disengagement of the lock. 1. Series CLJ2, CLM2, CLG1 1) Loose locking nut. 2) Supply air pressure of.3 MPa or more to the lock release port. 3) Turn the wrench flats section of the manual unlocking cam until it stops at the FREE position that is marked on the cam guide. ) While keeping the wrench flats section in place, tighten the lock nut. CLJ2 CLM2 CLG1 CL1 MLGC CNG MN CN CNS CLS CLQ RLQ MLU MLGP ML1C D- 99

103 Prior to Use Construction Principle/pplicable Series: CLJ2, CLM2, CLG1, MLGC Spring locking type Release port Fulcrum (Rotary axis) rake shoe ir pressure supply rake arm Roller Tapered brake piston rake spring Pressurized lock port (Plug with breathing hole for spring lock) ir pressure exhaust pplication point C Power point Unlocked state Locked state Spring locking (Exhaust locking) The spring force that is applied to the tapered brake piston becomes amplified through the wedge effect. This force becomes further amplified to the power of /C through the mechanical advantage of a lever and acts on the brake shoe, which in turn, applies a large force to tighten and lock the piston rod. To disengage the lock, air pressure is supplied through the unlocking port, thus disengaging the brake spring force. Pneumatic locking type ir pressure supply ir pressure exhaust ir pressure exhaust ir pressure supply Unlocked state rake piston is operated by air pressure. Locked state Spring and pneumatic locking type ir pressure supply ir pressure exhaust ir pressure exhaust ir pressure supply Unlocked state Locked state rake piston is operated by air pressure and spring force.

104 Fine Lock Cylinder Double cting, Single Rod Series CLJ2 ø With auto switch With auto switch (uilt-in magnet) CLJ2 CDLJ2 L F D uilt-in Magnet Cylinder Model L L Mounting style asic style xial foot style Rod side flange style Double clevis style If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (Example) CDLJ2--P Nil R mm Standard stroke ø, 3,,,,,,, 1, 2 How to Order R R Port location on head cover Perpendicular to axis xial direction E E M9W Lock operation E Spring locking (Exhaust locking) P Pneumatic locking (Pressure locking) D Spring and pneumatic locking Made to Order Refer to page 2 for details. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Nil Without auto switch For the applicable auto switch model, refer to the table below. CLJ2 CLM2 CLG1 CL1 MLGC CNG MN CN CNS CLS CLQ RLQ MLU MLGP ML1C pplicable uto Switch/Refer to pages 119 to for further information on auto switches. Indicator light Type Special function Electrical Wiring entry (Output) Solid state switch Reed switch Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Grommet Connector Grommet Grommet Connector Yes Yes Yes No No 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire -wire (NPN) 3-wire (NPN equivalent) 2-wire Lead wire length symbols:. m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL m Z (Example) M9NWZ None N (Example) HCN 2 V 2 V Load voltage DC V, V V V, V V V, V V V C V or less 2V or less model M9N M9P M9 HC M9NW M9PW M9W H HNF C3C CC Lead wire length (m). (Nil) 1 (M) 3 (L) (Z) None (N) Pre-wired connector pplicable load Relay, PLC Relay, PLC Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages 1 and 1. D-9V/M9V/M9WV/D-M9(V)L types cannot be mounted. Solid state auto switches marked with are produced upon receipt of order. D-9/M9/M9W auto switches are shipped together (not assembled). (Only auto switch mounting brackets are assembled at the time of shipment.) D-C/C/H auto switches are assembled at the time of shipment. 1 D-

105 Series CLJ2 Provided with a compact lock mechanism, it is suitable for intermediate stop, emergency stop, and drop prevention. Locking in both directions The piston rod can be locked in either direction of its cylinder stroke. Maximum piston speed: mm/s It can be used at to mm/s provided that it is within the allowable kinetic energy range. Head Cover Port Location Either perpendicular to the cylinder axis or in-line with the cylinder axis is available for basic style. xial Perpendicular Made to Order Specifications (For details, refer to page 13.) Specifications ction Lubricant Lock operation Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Cushion length tolerance Mounting Fine Lock Specifications Spring locking Lock operation (Exhaust locking) Fluid Maximum operating pressure Unlocking pressure Lock starting pressure Locking direction Standard /.3 MPa or more Double acting, Single rod Not required (Non-lube) Spring locking (Exhaust locking) Pneumatic locking (Pressure locking) Spring and pneumatic locking ir 1. MPa. MPa. MPa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) to mm/s Rubber bumper + 1. asic style, xial foot style, Rod side flange style, Double clevis style Constraints associated with the allowable kinetic energy are imposed on the speeds at which the piston can be locked. The maximum speed of mm/s can be accommodated if the piston is to be locked in the stationary state for the purpose of drop prevention. Spring and pneumatic locking ir. MPa.2 MPa or less oth directions Pneumatic locking (Pressure locking).1 MPa or more. MPa or more Refer to the minimum auto switch mounting stroke (page 9) for those with an auto switch. Standard stroke, 3,,,,,,, 1, 2 Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Mounting racket and ccessory/for details, refer to page. Mounting asic style xial foot style Rod side flange style Double clevis style Symbol -X Specifications Change of rod end shape Refer to pages to for cylinders with auto switches. Minimum auto switch mounting stroke Proper auto switch mounting position (detection at stroke end) and mounting height Operating range Switch mounting bracket: Part no. Standard equipment Option Mounting nut Clevis pin Single knuckle joint Double knuckle joint (With pin) T-bracket Pins and retaining rings are packaged together with double clevis and double knuckle joint. Mounting racket Part No. Mounting bracket Part no. Foot CLJ-L Flange CLJ-F T-bracket CJ-T T-bracket is used with double clevis (D). 2