Dual rod cylinder with guide function for pick & place applications.

Transcription

1 Dual Rod Cylinder Series CXS ø, ø0, ø, ø, ø2, Dual rod cylinder with guide function for pick & place applications. Series CXS Twice the thrust Non-rotating accuracy ±0. MX MY CY MG CX - Ball bushing bearings and slide bearings are standard for all series. Dimensions for ball bushing bearings and slide bearings are the same. djustable stroke range: 0 to mm Work can be mounted on three faces. SeriesVariations Series Bore size xial foot piping Clean Series - 2- Page Compact type Basic type With air cushion CXSJ CXS CXS (ø only) (Ball bushing bearing only) (Ball bushing gbearing only) With end lock CXS Double rod type CXSW

2 Compact type With air cushion Two new additions: Dual rod cylinder Compact type Series CXSJ: ø, ø0, ø, ø, ø2, Smaller and lightweight Dimensions/Weight Overall length CXS standard Superior mounting option Reverse mounting CXSJ Width Height uto switches can be installed from 3 directions. Bore size ø ø0 ø ø ø2 Series CXSJ CXS CXSJ0 CXS0 CXSJ CXS CXSJ CXS CXSJ2 CXS2 CXSJ32 CXS Symmetric mounting Dimensions Height Width Overall length 42 + Stroke 8. + Stroke + Stroke 72 + Stroke 70 + Stroke 79 + Stroke 84 + Stroke 94 + Stroke 87 + Stroke 9 + Stroke Stroke 2 + Stroke Weight (kg) Note) Slide bearing, mm strokes llowable kinetic energy, allowable load, and non-rotating accuracy are equivalent to those of standard type CXS. Note) Reverse mounting mechanism Bolt holder Reverse mounting uto switch Mounting bolt xial piping available (ø, ø0) Bolt holder Since the bolt holder is movable, the mounting bolt does not interfere with the auto switch no matter what direction it is mounted from

3 range is better than ever. With air cushion Series CXS: ø, ø2, ir cushion only minimally adds to full length dimension, compared with the standard type cylinder. Unique air cushion mechanism with no cushion ring Elimination of the cushion ring used in conventional type air cushions has made it possible to reduce the overall length of the cylinder while retaining all the advantages of a compact profile. Working principle dditional dimension for each bore size compared to the basic type CXS basic type + + Piston seal R H 2 mm (ø) 3 mm (ø2) mm () Cushion needle Improved allowable kinetic energy: Two to three times that of the standard type 2 Improved noise reduction: Reduction of more than db is possible R H Compact type Series CXSJ ø, ø0, ø, ø, ø2, Basic type Series CXS ø, ø0, ø, ø, ø2, With air cushion Series CXS ø, ø2, W With end lock Series CXS ø, ø0, ø, ø, ø2, MX MY CY MG CX -. When the piston is retracting, air is exhausted through both and until piston seal H passes air passage. 2. fter piston seal H has passed air passage, air is exhausted only through. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. 3. When air is supplied for the piston extension, the check seal opens and the piston extends with no delay. Clean Series - Series CXSJ: ø, ø0 2- Series -CXSJ 2-CXSJ Type Vacuum specifications Relieving type Special treatment Bearing Slide bearing Ball bushing bearing Ball bushing bearing Double rod type Series CXSW ø, ø0, ø, ø, ø2,

4 Series CXSJ Specific Product Precautions Be sure to read before handling. Caution Mounting. Make sure that the surface on which the cylinder is to be mounted is flat (reference value for flatness: 0.0 or less). Dual-rod cylinders can be mounted from 3 directions, however, make sure that the surface on which the cylinder is to be mounted is flat (reference value for flatness: 0.0 or less). Otherwise, the accuracy of the piston rod operation is not achieved, and malfunctioning can occur. 2. The piston rod must be retracted when mounting the cylinder. Scratches or gouges in the piston rod may lead to damaged bearings and seals and cause malfunctions or air leakage. 3. CXSJ (ø, ø0) djust the bolt holder using a hexagon wrench 3 mm in width across flats so that it does not protrude from the cylinder surface (approx. 0. mm depth from the cylinder surface to the top of the holder). If the bolt holder is not properly adjusted, it can interfere with the switch rail, hindering the auto switch mounting. The required length of the mounting bolt for a bolt holder and mounting hole in the rod cover side varies depending on the bearing surface position for the mounting bolt. Refer to dimensions l and l2 provided below to select the appropriate mounting bolt length. B Caution. fter adjusting the stroke, make sure to tighten the hexagon nut to prevent it from loosening. Dual-rod cylinders have a bolt to adjust 0 to mm strokes on the retracted end (IN). Loosen the hexagon nut to adjust the stroke; however, make sure to tighten the hexagon nut after making an adjustment. 2. Never operate a cylinder with its bumper bolt removed. lso, do not attempt to tighten the bumper bolt without using a nut. If the dumper bolt is removed, the piston hits the head cover causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3. bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent settling, use a following part numbers for ordering. Bore size Part no. Qty. Stroke djustment CXS , CXS , 2 CXS CXS Section B B CXSJ CXSJ0 l2 B Bolt holder (movable) l Piping. For axial piping, the side port of the standard cylinder is plugged. However, a plugged port can be switched according to the operating conditions. When switching the plugged port, check the air leakage. If small air leakage is detected, unplug the port, then check the seat surface, and reassemble it. l pprox. 0. or less Section l Disassembly and Maintenance Caution. Never use a cylinder with its plate removed. When removing the hexagon socket head cap screw on the end plate, the piston rod must be secured to prevent from rotating. However, if the sliding parts of the piston rod are scratched and gouged, a malfunction may occur. 2. When disassembling and reassembling the cylinder, please contact SMC or refer to the separate instruction manual. Warning. Take precautions when your hands are near the plate and housing. When the cylinder is operated, take extra precautions to avoid getting your hands and fingers caught between the plate and housing, that can cause a bodily injury

5 Series CXS Specific Product Precautions Be sure to read before handling. Caution Mounting. Make sure that the surface on which the cylinder is to be mounted is flat (reference value for flatness: 0.0 or less). Dual rod cylinders can be mounted from 3 directions, however, make sure that the surface on which the cylinder is to be mounted is flat (reference value for flatness: 0.0 or less). Otherwise, the accuracy of the piston rod operation is not achieved, and malfunctioning can occur. 2. Piston rod must be retracted when mounting the cylinder. Scratches or gouges in the piston rod may lead to damaged bearings and seals and cause malfunctions or air leakage. 3. CXSJ djust the bolt holder using a hexagon wrench 3 mm in width across flats so that it does not protrude from the cylinder surface (approx. 0. mm depth from the cylinder surface to the top of the holder). If the bolt holder is not properly adjusted, it can interfere with the switch rail, hindering the auto switch mounting. The required length of the mounting bolt for a bolt holder and mounting hole in the rod cover side varies depending on the bearing surface position for the mounting bolt. Refer to dimensions l and l2 provided below to select the appropriate mounting bolt length. Piping Section B-B CXSJ CXSJ0 l2 B B Bolt holder (movable) l ~ = 0. or less Section - l Plug the appropriate supply port(s) according to the operating conditions. Dual-rod cylinders have 2 supply ports for each operating direction (3 supply ports for ø only). Plug the appropriate supply port according to the operating conditions. However, when switching the plugged port, verify air leakage. If small air leakage is detected, unplug the port, check the seat surface, and reassemble it. 2. CXSJ For axial piping, the side port of the standard cylinder is plugged. However, a plugged port can be switched according to the operating conditions. When switching the plugged port, check for air leakage. If small air leakage is detected, unplug the port, check the seat surface, and reassemble it. l Caution Stroke djustment. fter adjusting the stroke, make sure to tighten the hexagon nut to prevent it from loosening. Dual rod cylinders have a bolt to adjust 0 to strokes on the retracted end (IN). Loosen the hexagon nut to adjust the stroke; however, make sure to tighten the hexagon nut after making an adjustment. 2. Never operate a cylinder with its bumper bolt removed. lso, do not attempt to tighten the bumper bolt without using a nut. If the bumper bolt is removed, the piston hits the head cover causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3. bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent settling, use following part numbers for ordering. Bore size Part no. Qty., 0, CXS , 2 CXS Disassembly and Maintenance Caution. Never use a cylinder with its plate removed. When removing the hexagon socket head cap screw on the end plate, the piston rod must be secured to prevent from rotating. However, if the sliding parts of the piston rod are scratched and gouged, a malfunction may occur. If the plate is not required for your application, use the cylinder that does not come with a plate, available through made-to-order (93) on page When disassembling and reassembling the cylinder, please contact SMC or refer to the separate instruction manual. Warning. Take precautions when your hands are near the plate and housing. Take sufficient care to avoid getting your hands or fingers caught when the cylinder is operated. 32 CXS MX MY CY MG CX

6 Compact Type: CXSJ Vertical Mounting Series CXSJ Selection Caution Confirmation of theoretical output is required separately. Refer to Theoretical Output on page l l Mounting orientation m m Max. speed (mm/s) Stroke ø ø0 Selection graph ø ø ø2 Up to 0 Up to 0 Up to 00 Up to 800 ll strokes () (2) (3) (4) Horizontal Mounting l Mounting orientation m m Refer to the caution notes below. Stroke ø0 ø ø ø2 Caution Up to 0 If the cylinder is horizontally mounted and the plate end does not reach the load s center of gravity, use the formula below to calculate the imaginary stroke l that includes the distance between the load s center of gravity and the plate end. Select the graph that corresponds to the imaginary stroke l. Imaginary stroke l = (Stroke) + k + l k: Distance between the center and end of the plate ø 2.7 mm ø0 4 mm ø mm ø mm ø2 8 mm Up to Up to 0 Up to 7 Up to 00 Max. speed (mm/s) Up to 0 more than 0 Up to 0 more than 0 Up to 0 more than 0 Up to 0 more than 0 Up to 0 more than 0 ø () () (7) Selection graph The maximum speeds for ø to are: ø, 0: Up to 800 mm/s; ø, : Up to 700 mm/s; ø2, 32: Up to 00 mm/s (8) (9) (0) () (2) (3) (Example). When using CXSJM-0 and l = mm: Imaginary stroke l = = 27.7 Therefore, the graph used for your model selection should be the one for CXSJM- () ). 2. When using CXSJL2-0 and l = 0 mm: Imaginary stroke l = = 7 Therefore, the graph used for your model selection should be the one for CXSJL2-7 (4) ). (4) () l k

7 Selection Series CXS Vertical Mounting Graph () V = Up to 0 mm/s CXSJM CXSJL Graph (2) V = Up to 0 mm/s CXSJM CXSJL Overhang L Graph (3) V = Up to 00 mm/s ø2 ø ø ø0 ø CXSJM CXSJL Overhang L Graph (4) V = Up to 800 mm/s (Up to 700 mm/s for ø, ) ø2 ø ø ø0 ø CXSJM CXSJL MX MY CY MG CX - ø2 ø 0. ø ø 0. ø ø0 0. ø0 0. ø ø Overhang L Overhang L Note) V = 700 mm/s for ø, ø

8 Series CXS Horizontal Mounting Graph () Up to 0 mm stroke 0.2 V = Up to 0 mm/s V = Up to 800 mm/s Graph () Up to mm stroke 0.2 V = Up to 0 mm/s V = Up to 800 mm/s CXSJM CXSJL CXSJM CXSJL 0 Overhang L Overhang L Graph (8) UV = Up to 0 mm/s; Up to 0 mm stroke CXSJM CXSJL Graph (9) UV = Over 0 mm/s; Up to 0 mm stroke CXSJM CXSJL 0. ø2 ø 0. ø2 ø ø ø ø Overhang L Overhang L ø0 Graph (2) V = Up to 0 mm/s; Up to 0 mm stroke CXSJM CXSJL Graph (3) V = Over 0 mm/s; Up to 0 mm stroke CXSJM CXSJL 0. ø2 0. ø2 ø ø ø ø 0.0 ø0 0.0 ø Overhang L Overhang L

9 Selection Series CXS Graph (7) Up to 0 mm stroke 0.2 V = Up to 800mm/s CXSJM MX MY 0.02 CY CXSJL MG Overhang L 0 CX Graph (0) V = Up to 0 mm/s; Up to mm stroke CXSJM CXSJL Graph () V = Over 0 mm/s; Up to mm stroke CXSJM CXSJL - 0. ø2 0. ø2 ø ø ø ø Overhang L ø Overhang L ø0 Graph (4) V = Over 0 mm/s; Up to 7 mm stroke CXSJM CXSJL Graph () V = Over 0 mm/s; Up to 00 mm stroke CXSJM CXSJL ø Overhang L ø2 ø ø Overhang L ø2 ø ø

10 Series CXS Selection Caution Confirmation of theoretical output is required separately. Refer to Theoretical Output on page Basic Type: CXS Vertical Mounting l l MX Mounting orientation m m MY CY Max. speed (mm/s) Stroke ø ø0 Selection graph ø ø ø2 Up to 00 Horizontal Mounting Up to 0 () (2) (3) Up to 0 Up to 0 ll strokes (4) Up to 00 () Up to 700 (Up to 800) () MG CX - Mounting orientation l m m Refer to the caution notes below. Stroke Max. speed (mm/s) Selection graph ø ø0 ø ø ø2 Up to 00 Caution Up to 0 Up to Up to Up to 0 0 More Up to Up to Up to than than More Up to 0 00 (7) (8) (9) Up to 0 Up to 0 Up to 0 than More 0 Up to 00 Up to 7 Up to 0 Up to 0 than More 0 Up to 00 Up to 00 Up to 0 Up to 0 More than 0 (0) () (2) (3) (4) () () (7) The maximum speeds for ø0 to are: ø0: up to 800 mm/s; ø, : up to 700 mm/s; ø2, 32: Up to 00 mm/s If the cylinder is horizontally mounted and the plate end does not reach the load s center of gravity, use the formula below to calculate the imaginary stroke l that includes the distance between the load s center of gravity and the plate end. Select the graph that corresponds to the imaginary stroke l. l k Imaginary stroke l = (Stroke) + k + l k: Distance between the center and end of the plate ø ø0 ø ø ø2 2.7 mm 4 mm mm mm 8 mm (Example) When using CXSM-0 and l = mm: Imaginary stroke l = = 27.7 Therefore, the graph used for your model selection should be the one for CXSM

11 Series CXS Vertical Mounting ø Graph () V = 00 mm/s Graph (2) V = 0 mm/s 0.0 CXSL 0. CXSM CXSL CXSM Overhang l Overhang l ø0 to Graph (3) V = 0 mm/s 0 Graph (4) V = 0 mm/s 4 3 ø2 ø 0. ø2 ø ø 0. ø 0. CXSM CXSL ø0 0. CXSM CXSL ø0 Overhang l Overhang l Graph () V = 00 mm/s Graph () V = 700 mm/s (800 mm/s for ø0) 2 0. ø ø2 ø 0.4 ø 0. ø 0.2 ø0 0. CXSM CXSL ø0 0. CXSM CXSL Overhang l Overhang l

12 Selection Series CXS Horizontal Mounting ø ø0 to Graph (7) Up to 0 st CXSM CXSL CXSL Graph (8) Up to st Overhang l V = Up to 00 mm/s V = Up to 0 mm/s CXSM Graph (9) Up to 0 st Overhang l V = Up to 00 mm/s V = Up to 0 mm/s V = Up to 00 mm/s V = Up to 0 mm/s Graph (0) V = Up to 0 mm/s; Up to 0 st Overhang l CXSM CXSL Graph () V = Over 0 mm/s; Up to 0 st CXSM CXSL ø2 ø ø ø0 ø2 ø ø MX MY CY MG CX ø Overhang l Graph (2) V = Up to 0 mm/s; Up to st CXSL 2 CXSM CXSL 0.0CXSM Overhang l ø2 ø ø ø0 Overhang l

13 Series CXS Horizontal Mounting ø0 to Graph (3) V = Over 0 mm/s; Up to st 2 CXSM CXSL Graph (4) V = Up to 0 mm/s; Up to 0 st 2 CXSM CXSL ø2 ø ø ø2 ø ø Overhang l Graph () V = Over 0 mm/s; Up to 0 st CXSM CXSL ø ø Overhang l Graph () V = Over 0 mm/s; Up to 7 st CXSM CXSL ø2 ø ø2 ø ø ø ø0 ø Overhang l Graph (7) V = Over 0 mm/s; Up to 00 st CXSM CXSL Overhang l 0. ø2 ø ø Overhang l

14 With ir Cushion: CXS Vertical Mounting Series CXS Selection Caution Confirmation of theoretical output is required separately. Refer to Theoretical Output Table on page l l MX Mounting orientation m m MY CY MG CX Max. speed (mm/s) Stroke ø Selection ø2 graph Horizontal Mounting Up to 0 Up to 0 Up to 00 Up to 800 ll strokes () (2) (3) (4) Up to 000 () - Mounting orientation l m m Refer to the caution notes below. Stroke Max. speed (mm/s) Selection graph Imaginary stroke l = (Stroke) + k + l k: Distance between the center and the end of the plate ø ø2 ø ø2 Up to 0 Up to Up to 800 Up to 000 Up to 800 Up to 000 Up to 000 mm 8 mm Up to 0 () (7) (8) (9) (0) Caution If the cylinder is horizontally mounted and the plate end does not reach the load's center of gravity, use the formula below to calculate the imaginary stroke l that includes the distance between the load's center of gravity and the plate end. Select the graph that corresponds to the imaginary stroke l. (Example) When using CXSM-0 and l = 0 mm: Imaginary stroke l = = 2 Therefore, the graph used for your model selection should be the one for CXSM-. l k Up to 7 Up to 000 () Up to 00 Up to 000 (2) 8-28-

15 Series CXS Vertical Mounting Graph () V = 0 mm/s 0 CXSM CXSL Graph (2) V = 0 mm/s CXSM CXSL ø2 ø Overhang l ø2 ø Overhang l Graph (3) V = 00 mm/s Graph (4) V = 800 mm/s 3 0. ø2 CXSM ø CXSL CXSM CXSL ø2 ø Overhang l Overhang l Graph () V = 000 mm/s 3 CXSM CXSL 2 ø2 ø Overhang l 8-28-

16 Selection Series CXS Horizontal Mounting Graph () V = Up to 800 mm/s; Up to 0 st 3 CXSM CXSL Graph (7) V = Up to 000 mm/s; Up to 0 st 3 CXSM CXSL Overhang l Graph (8) V = Up to 800 mm/s; Up to st CXSM CXSL ø2 ø Overhang l Graph (9) V = Up to 000 mm/s; Up to st CXSM CXSL ø2 ø MX MY CY MG CX ø2 ø ø2 ø - Overhang l Overhang l Graph (0) V = Up to 000 mm/s; Up to 0 st 2 CXSM CXSL Graph () V = Up to 000 mm/s; Up to 7 st 2 CXSM CXSL 0. ø2 0. ø ø ø Overhang l Overhang l Graph (2) V = Up to 000 mm/s; Up to 00 st CXSM CXSL 0. ø Overhang l ø

17 Dual Rod Cylinder: Compact Type Series CXSJ ø, ø0, ø, ø, ø2, How to Order Piping Nil Nil TN TF M thread Rc /8 NPT /8 G /8 Thread type ø to ø2 Nil P Standard piping (ø to ) xial piping (ø, ø0) Standard piping Port location xial piping Port location CXS J M P 0 F9BW S Compact type M L Bearing type Slide bearing Ball bushing bearing uto switch Nil Number of auto switches Nil S n Bore size/stroke Bore size Standard stroke 0,,,, 0 0 0,,,, 0, 7 0,,,, 0, 7, pcs. pc. n pcs. Without auto switch (Built-in magnet) For the applicable auto switch model, refer to the table below. The auto switches are shipped together, (but not assembled). pplicable uto Switch/Refer to page 8-- for further information on auto switches. Type Reed switch Solid state switch Special function Diagnostic indication (2-color indication) Electrical entry Grommet Grommet Indicator light Yes Yes Wiring (Output) 3-wire (NPN equiv.) Load voltage 2-wire 2 V Water resistant (2-color indication) Lead wire length symbols: 0. m... Nil (Example) 93 3 m... L (Example) 93L m... Z (Example) M9NZ DC C V 2-wire 24 V 2 V 3-wire (NPN) 3-wire (PNP) V,2 V 2-wire 2 V 3-wire (NPN) 24 V 3-wire (PNP) V,2 V 00 V uto switch model Perpendicular Refer to page for additional details and applicable auto switches other than the above types. Please contact SMC for detailed auto switch with pre-wired connector. 9V 93V M9NV M9PV M9BV F9NWV F9PWV F9BWV In-line 9 93 M9N M9P M9B F9NW F9PW F9BW F9B Lead wire length (m) 0. (Nil) 3 (L) (Z) Pre-wired connector pplicable load IC circuit IC circuit IC circuit Solid state switches marked with are produced upon receipt of order. Relay, PLC Relay, PLC

18 Dual Rod Cylinder: Compact Type Series CXSJ Specifications Bore size Fluid Proof pressure Max. operating pressure Min. operating pressure 0. MPa ir (Non-lube).0 MPa 0.7 MPa 0. MPa 0.0 MPa mbient and fluid temperature 0 to 0 C (With no freezing) Piston speed to 800 mm/s to 700 mm/s to 00 mm/s Cushion Stroke adjustable range Rubber bumper on both ends 0 to mm compared to the standard stroke Port size M3 0. M 0.8 Rc (NPT, PF) /8 The maximum piston speed shown in the table above is for extension. The maximum piston speed for retraction is approximately 70% that of extension. Standard Stroke CXSJ CXSJ0 CXSJ CXSJ, 2, 32 Theoretical Output Standard strokes 0,,,, 0 0,,,, 0, 7 0,,,, 0, 7, 00 Strokes beyond the standard stroke range are available as a special order. Bore size Rod size Operating direction Piston area (mm 2 ) Manufacturable stroke range to to 0 0 to 0 0 to 0 Operating pressure (MPa) CXS CXS0 CXS CXS CXS2 CXS OUT IN OUT IN OUT OUT OUT OUT IN IN IN IN Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2 ) (N) MX MY CY MG CX - Weight CXSJM CXSJL CXSJM0 CXSJL0 CXSJM CXSJL CXSJM CXSJL CXSJM2 CXSJL2 CXSJM32 CXSJL Standard stroke Note) For axial piping of CXSJP- and CXSJ0P-, please add the following weight. CXSJP-: kg, CXSJ0P-: 0.04 kg (kg)

19 Series CXSJ Construction: Standard Piping CXSJM (Slide bearing) CXSJL (Ball bushing bearing) CXSJM t! CXSJM0!3 y!0! eq@8! u!7 oi CXSJL0!3 rq@8! u!7 oi Rod cover Piston rod B-side piston Rod cover Piston rod B-side piston Component Parts No. Description Material Note No. Description Material Note q w e Housing Piston rod Piston rod B Carbon steel Note) Carbon steel Note) Hard anodized Hard chromium electroplated Hard chromium electroplated!!7!8 Bumper B Piston seal Rod seal Polyurethane r Rod cover luminum bearing alloy!9 O-ring t Head cover O-ring y Plate Glossy, self-coloring hard Seal retainer Stainless steel u Piston Snap ring B i Piston B Bolt holder Stainless steel o Magnet Magnetic Bearing spacer luminum bearing alloy!0 Bumper bolt Carbon Ball bushing! Hexagon nut Carbon Piston rod Hard chromium electroplated!2 Bumper Piston rod B Hard chromium electroplated!3 Hexagon socket head cap screw Chromium O-ring!4 Hexagon socket head set screw Chromium Piston C Stainless steel! Snap ring #0 Bumper holder Resin Note) Stainless steel for CXSJM. Replacement Parts: Seal Kit CXSJ CXSJ0 Kit no. CXSJ-PS CXSJ0-PS Content Items!7,!8, from the chart above 8-28-

20 Dual Rod Cylinder: Compact Type Series CXSJ Construction: Standard Piping CXSJM (Slide bearing) CXSJL (Ball bushing bearing) CXSJM CXSJL!2!4!0 r! iou!7 iou!7t! MX MY CY!3 y! e q!3 y!@7 q MG CXSJM to 32 CXSJL to r! i o u!7 #0! i o u!7 t! CX - Rod cover Head cover Rod cover Head cover Component Parts No. Description Material Note No. Description Material Note q Housing Hard anodized! Bumper B Polyurethane w Piston rod Carbon steel Hard chromium electroplated!7 Piston seal e Piston rod B Carbon steel Hard chromium electroplated!8 Rod seal r Rod cover luminum bearing alloy!9 O-ring t Head O-ring y Plate Glossy, self-coloring hard Seal retainer Stainless steel u Piston Snap ring B i Piston B Stainless Bolt holder Stainless steel o Magnet Magnetic Bearing spacer Resin!0 Bumper bolt Carbon Ball bushing! Hexagon nut Carbon Piston rod Hard chromium electroplated!2 Bumper Piston rod B Hard chromium electroplated!3 Hexagon socket head cap screw Chromium O-ring!4 Hexagon socket head set screw Chromium Piston C Stainless steel! Snap ring #0 Bumper holder Resin Replacement Parts: Seal Kits CXSJM CXSJM CXSJM2 CXSJM32 CXSJL CXSJL CXSJL2 CXSJL32 Kit no. CXSM-PS CXSM-PS CXSM2-PS CXSM32-PS CXSLPS CXSLPS CXSL2PS CXSL32PS Content Items!7,!8, and!9 from the chart above

21 Series CXSJ Construction: xial Piping CXSJP, CXSJ0P r w t q e o i y u Component Parts No. Description Material Note q w e r t y u i o Cover dapter Hexagon socket head cap screw Hexagon socket head plug O-ring O-ring Steel ball Steel ball Steel ball Chromium steel Chromium steel Hard anodized nodized Hard chromium electroplated Hard chromium electroplated Hard chromium electroplated Parts other than those listed above are the same as those for CXSJ basic type. Clean Series There are two types of cylinders, relieving type and vacuum type, available for a clean room environment. The relieving type specification with the double-seal construction of the rod section allows the cylinder to channel exhaust through the relief port directly to the outside of a clean room environment. The vacuum type specification allows for the application of a vacuum on the rod section while forced exhaust of air takes place through the vacuum port to the outside of a clean room environment. How to Order CXSJ M Bearing type Clean room specifications 2 Bore size Stroke uto switch M Slide bearing L Ball bushing bearing Only ball bushing bearing is available for clean room specification 2-. Vacuum type Relieving type (With specially treated sliding parts) Bore size/stroke 0 0,,,, 0 0,,,, 0 Specifications Bore size Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Stroke adjustable range Bearing type Refer to the SMC Clean Series catalog for dimensions..0 MPa 0.7 MPa 0. MPa 0. MPa 0 to 0 C (With no freezing) to 0 mm/s 0 0 to mm compared to the standard stroke Slide bearing, Ball bushing bearing

22 Dual Rod Cylinder: Compact Type Series CXSJ Dimensions: ø Standard Piping Stroke 4-M3 x 0. thread depth M3 x 0. thread depth 3. (Piping port) MX MY M3 x 0. x 3l (Hexagon socket head set screw) M8 x.2 x 7.l (Bolt holder) CY MG CX - 2-M3 x 0. through 2-M3 x 0. through M2. x 0.4 x l (Hexagon socket head cap screw) ø3.4 through ø. counterbore with depth (Opposite side: Same) M3 x 0. x 2.l (Hexagon head bolt) M3 x 0. (Hexagon nut) 2-M3 x 0. through ø Stroke Stroke 32 + Stroke 2 + Stroke ±0.2 2 ± (2) ( + Stroke) 2 ±

23 Series CXSJ Dimensions: ø0 Standard Piping 2 + Stroke 4-M3 x 0. thread depth 4. Stroke Stroke ± ± M x 0.8 thread depth 4 (Piping port) + Stroke M x 0.8 x 4l (Hexagon socket head set screw) Stroke M8 x.2 x 7.l (Bolt holder). 2-M4 x 0.7 through 2-M3 x 0. through M3 x 0. x 0l (Hexagon socket head cap screw) ø3.4 through ø. counterbore with depth. (Opposite side: Same) M4 x 0.7 x 4.l (Hexagon head bolt) M4 x 0.7 (Hexagon nut) 2-M3 x 0. through 4 () (8 + Stroke) ø 33 ±

24 Dual Rod Cylinder: Compact Type Series CXSJ Dimensions: ø, ø0 xial Piping CXSJP Stroke MX MY CY MG CX Stroke (4. + Stroke) + Stroke Stroke 8 + Stroke Stroke (49 + Stroke) 42 + Stroke 32 + Stroke 2 + Stroke M. x 0.3 x L 2-M3 x 0. thread depth 3. (Piping port) OUT IN Steel balls CXSJ0P 2 + Stroke 4-M. x 0.3 x 8 L M x 0.8 thread depth 4 (Piping port) OUT IN Steel balls

25 Series CXSJ Dimensions: ø to 32 Standard Piping U R T Stroke ZZ + Stroke J K SS + Stroke I L Z M NN C (G) G ± 0.2 (G) H Q B D E F (Through) N (I) (L) (Z) Bore size B ZZ C D E F 2-M x M x M x.0 2-M x.0 G H I 8 J K L 2 M 2 x 2-ø4.3 through 2 x 2-ø8 counterbore with depth x 2-ø. through 2 x 2-ø9. counterbore with depth.3 2 x 2-ø. through 2 x 2-ø counterbore with depth.3 2 x 2-ø. through 2 x 2-ø counterbore with depth.3 N 2-M4 x 0.7 with depth 2-M4 x 0.7 with depth 2-M x 0.8 with depth 7. 2-M x 0.8 with depth 7. NN ø8 ø0 ø2 ø Q R T U 2-M x 0.8 thread depth 4 2-M x 0.8 thread depth 4 2-M x 0.8 thread depth 4 2-Rc /8 thread depth SS Bore size Symbol Stroke 0,,, Z

26 Dual Rod Cylinder: Compact Type Series CXSJ Proper uto Switch Mounting Position (Detection at stroke end) CXSJ/0 CXSJ to 32 uto Switch Mounting Dimensions CXSJ/0 9 (Reed switch) CXSJ to 32 B B F9W M9 (Solid state switch) Mounting of uto Switch Watchmakers screw driver Set screw B Electrical entry direction: Inward C C uto switch C 9V (Reed switch) C3 D D Electrical entry direction: Outward 9 (Reed switch) F9W (Solid state switch) M9 C C3 Use a watchmakers screwdriver with a handle to mm in diameter when tightening the auto switch mounting screw. Tightening torque should be approximately 0.0 to 0. N m. C2 C2 Operating Range D uto switch model 9/9V F9W F9WV F9BL M9, M9V D2 M9V F9WV (Solid state switch) 9V (Reed switch) F9WV (Solid state switch) M9V uto switch model 9 F9 W, M9 9V M9V, F9WV uto switch model F9W, M9 Caution. void proximity to magnetic objects When magnetic substances such as iron (including flange brackets) are in close proximity of an auto switch cylinder, be sure to provide a clearance between the magnetic substance and the cylinder body as shown in the drawing below. If the clearance is less than 0 mm, the auto switch may not function properly Bore size The operating ranges are provided as guidelines including hystereses and are not guaranteed values (assuming approximately ±% variations). They may vary significantly with ambient environments. Bore size Bore size , 9 B 9 C F9BL B C D D B 9 C D B C Symbol C C2 C3 Symbol B C C2, C3 D D2 F9W, M9 D mm 2 8 Bore size, Bore size mm M9V, F9WV B C D Note ) ø: 90, 9, 93, F9BL ø0: 90, 9, 93 Only outward electrical entry (D dimension) is available. Note 2) Minus value in D column (ø, ø, ø2, ) means that the auto switches are to be mounted beyond the cylinder body edges. 9V, F9WV M9V MX MY CY MG CX - Other than the applicable auto switches listed in How to Order, the following auto switches can be mounted. For detailed specifications, refer to page 8--. Type Electrical entry Features Reed switch 90 90V Grommet (In-line) Grommet (Perpendicular) Without indicator light Please contact SMC for detailed normally closed solid (N.C. = b contact) state auto switches such as F9G and F9H

27 Dual Rod Cylinder: Basic Type Series CXS ø, ø0, ø, ø, ø2, M L CXS M Bearing type Slide bearing Ball bushing bearing Bore size/stroke Bore size Standard stroke 0,,,, 0 How to Order 00 Y7BW S Number of auto switches Nil S n 2 pcs. pc. n pcs. 0,,, 2,, 3,, 4, 0 uto switch 0, 0, 70, 7 Nil Without auto switch (Built-in magnet), 0,,, 2,, 3,, 4, For the applicable auto switch model, refer to the table below. 2, 32 0, 0, 70, 7, 80, 90, 00 uto switches are shipped together, (but not assembled). MX MY CY MG CX - pplicable uto Switch/Refer to page 8-- for further information on auto switches. Type Reed switch Solid state switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) Electrical entry Grommet Grommet Indicator light Yes Yes Wiring (Output) Load voltage DC 3-wire (NPN equivalent) V 2-wire 3-wire (NPN) 3-wire (PNP) 24 V 2 V V, 2 V 2-wire 2 V 3-wire (NPN) 3-wire (PNP) 24 V V, 2 V 2-wire 2 V C uto switch model Perpendicular In-line Z7 00 V Y9 Y7PV Y9B Y7NWV Y7PWV Y7BWV Z73 Y9 Y7P Y9B Y7NW Y7PW Y7BW Y7B Lead wire length (m) Pre-wire 0. 3 connector (Nil) (L) (Z) pplicable load IC circuit Relay, PLC IC circuit IC Relay, circuit PLC Lead wire length symbols: 0. m Nil (Example) Y9 3 m L (Example) Y9L m Z (Example) Y9Z Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wire connector, refer to page Solid state switches marked with are produced upon receipt of order

28 Series CXS Specifications Bore size Fluid Proof pressure Maximum operating pressure Minimum operating pressure 0. MPa ir (Non-lube).0 MPa 0.7 MPa 0. MPa 0.0 MPa mbient and fluid temperature 0 to 0 C (No freezing) Piston speed Cushion to 0 mm/s to 800 mm/s to 700 mm/s Rubber bumper to 00 mm/s Stroke adjustable range 0 to - mm compared to the standard stroke Port size M x 0.8 Rc /8 Bearing type Slide bearing, Ball bushing bearing (Same dimensions for both) The maximum piston speed shown in the table above is for extension. The maximum piston speed for retraction is approximately 70% that of extension. Standard Stroke Symbol B B9 B B3 B9 C8 C22 93 Weight Made to Order Specifications (For details, refer to page 8-3-.) Heat resistant cylinder (0 C) Low speed cylinder (0 to 0 mm/s) Long stroke type Low speed cylinder ( to 0 mm/s) High speed cylinder NPT finish piping port Fluoro rubber seals Without plate Specifications Standard stroke Manufacturable stroke range CXS CXS0 CXS CXS CXS2 CXS32 0,,,, 0 0,,, 2,, 3,, 4, 0, 0, 70, 7 0,,, 2,, 3,, 4, 0, 0, 70, 7, 80, 90, 00 0 to to 0 0 to 0 0 to 0 Refer to Made to Order Specifications for stroke which exceeds the standard stroke length. Non-standard strokes for a size ø cylinder are available as a special order. Theoretical Output Bore size Rod size Operating Piston area direction (mm 2 ) 0. Operating pressure (MPa) CXS 4 OUT IN CXS0 CXS CXS CXS2 CXS OUT IN OUT IN OUT OUT OUT IN IN IN Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2 ) (N) (kg) CXSM CXSL CXSM0 CXSL0 CXSM CXSL CXSM CXSL CXSM2 CXSL2 CXSM32 CXSL Standard stroke

29 Dual Rod Cylinder: Basic Type Series CXS Clean Series There are two types of cylinders, relieving type and vacuum type, available for a clean room environment. The relieving type specification with the double-seal construction of the rod section allows the cylinder to channel exhaust through the relief port directly to the outside of a clean room environment. The vacuum type specification allows for the application of a vacuum on the rod section while forced exhaust of air takes place through the vacuum port to the outside of a clean room environment. How to Order 2 CXS L Specifications Ball bushing bearing Clean room specifications 2 Bore size Stroke uto switch Vacuum type Relieving type (With specially treated sliding parts) Bore size Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Stroke adjustable range Bearing type 0. MPa Refer to Pneumatic Clean Series catalog for dimensions MPa.0 MPa 0.7 MPa 0 to 0 C (No freezing) to 0 mm/s 0 to mm compared to the standard stroke Ball bushing bearing 0.0 MPa MX MY CY MG CX - Copper-free (For CRT manufacturing process) To prevent the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. Note) Since the standard cylinders are essentially copper and fluorine-free, those are conforming to - specifications. However, in the event of combined specifications, it is likely to happen nonconformity to -specifications. (e.g. combination between - and B9 (B3)) In order to avoid such a non-conformity, we distinguish the model no. from the one for standard products by prefixing -. How to Order CXS L Bore size Stroke uto switch Ball bushing bearing Copper-free Specifieations and dimensions are the same as for standard products

30 Series CXS Operating Conditions Maximum Load Weight When the cylinder is mounted as shown in the diagrams below, the maximum load weight W should not exceed the values illustrated in the graph immediately following the diagrams. Deflection at the Plate End n approximate plate-end deflection X without a load is shown in the graph below. Deflection X mm Extended rod CXSM (Slide bearing) CXSL (Ball bushing bearing) Maximum load weight W (kg) Deflection X Stroke llowable Kinetic Energy Load weight and cylinder speed should be observed within the range given in the graph below. Cylinder speed should be adjusted using a speed controller. Cylinder stroke Non-rotating ccuracy Non-rotating accuracy θ without a load should be less than or equal to the value provided in the table below as a guide. Load weight (kg) Housing Plate Cylinder speed (mm/s) Bore size to 32 CXSM (Slide bearing) CXSL (Ball bushing bearing) ±

31 Dual Rod Cylinder: Basic Type Series CXS Construction: @8 @4 rw!3 ut! w!3i!0@2u q!4ye!!2 q@ CXSM to o i!0u@2t MX MY CY MG CX - Component Parts No. q w e r t y u i o!0!!2!3!4!!!7 Description Housing Piston rod Piston rod B Rod cover Head cover Plate Piston Piston B Bumper Magnet Bumper bolt Hexagon nut Bumper B Hexagon socket head cap screw Hexagon socket head set screw Snap ring Bumper holder!4 ye!!2 Material () Carbon steel () Carbon steel luminum bearing alloy (2) Polyurethane Magnetic material Carbon steel Carbon steel Polyurethane Chromium steel Chromium steel luminum bearing alloy Note ) Stainless steel for CXSM. Note 2) nodized aluminum alloy for CXSM. Note Hard anodized Hard chrome plated Hard chrome plated Hard anodized Chromated Chromated Component Description Ball bushing Bearing spacer Bumper Plug Piston seal Rod seal O-ring Head cover B Seal retainer Port spacer Steel ball Snap ring B Bore size Material luminum bearing alloy Polyurethane Chromium steel Replacement Parts: Seal Kit Kit no. CXSM-PS CXSM0PS CXSM-PS CXSM-PS CXSM2-PS CXSM32-PS Note Hard chrome plated Contents Set of @4 Seal @4. Order the seal kit, based on each bore size

32 Series CXS Construction: Ball Bushing Bearing rw!8!9!3 q CXSL to Component Parts: Standard Piping No. q w e r t y u i Description Housing Piston rod Piston rod B Rod cover Head cover Plate Piston Piston B Bumper Magnet Bumper bolt Hexagon nut Bumper B Hexagon socket head cap screw Hexagon socket head set screw Snap ring Bumper holder Material luminum bearing alloy Polyurethane Magnetic material Carbon steel Carbon steel Polyurethane Chromium steel Chromium steel Synthetic resin Note ) nodized aluminum alloy for CXSL. () Note Hard anodized Hard chrome plated Hard chrome plated Hard anodized Chromated Chromated Component Description Ball bushing Bearing spacer Bumper Plug Piston seal Rod seal O-ring Head cover B Seal retainer Port spacer Steel ball Snap ring B Material (2) Synthetic resin Polyurethane Chromium steel Note 2) for CXSL. Replacement Parts: Seal Kit Note Hard chrome plated Bore size Kit no. CXSL-PS Contents 0 CXSL0BPS CXSLPS CXSLPS Set of @4 2 CXSL2PS 32 CXSL32PS 8-29-

33 Dual Rod Cylinder: Basic Type Series CXS Dimensions: ø ST ZZ (8. + ST). 8 SS (4 + ST) 4 M3 x 0. x l (Hexagon socket head set screw) Z (0 + /2 ST) 2-ø3.4 through 2-ø. counterbore depth 3.3 OUT 3 3 MX 37 3 ± ± M3 x 0. (Through-hole) M2. x 0.4 x l (Hexagon socket headcap screw) M3 x 0. x 2.l, M3 x 0. (Hexagon bolt) (Hexagon nut) 2-M3 x 0. (Through-hole) 2-M x 0.8 thread depth 4. (Piping port) IN 0 2-M3 x 0. thread depth 4. (Opposite side: Same) 2-M x 0.8 thread depth 4. (Piping port) (Opposite side: Same) (3) ø4 () MY 7 CY MG CX S (3 + ST) - Z (0 + /2 ST) CXS-0 CXS- CXS- CXS- CXS-0 Stroke 0 0 Z 2 3 S SS ZZ

34 Series CXS Dimensions: ø0, ø B D Y (Hexagon socket head set screw) Stroke I J 9 L ZZ SS Z M X (Hexagon socket head cap screw) F (Through-hole) N M4 x 0.7 x 4.l, M4 x 0.7 (Hexagon bolt) (Hexagon nut).3 V (Opposite side: Same) 4-M x 0.8 thread depth 4. (Piping port) (Opposite side: Same) N U NN (G) G±0.2 (G) H P E (L) (Z) Q R 8 (I) (L) (Z) C QQ CXS0 CXS 4 8 B 7 C 44 D 8 Dimensions by Stroke Stroke Symbol CXS0 CXS E F 7. 2-M4 x M x G 3 4 H 2 I 4 J L M 2-ø3.4 through 2-ø. counterbore depth ø4.3 through 2-ø8 counterbore depth 4.4 N 2-M3 x 0. thread depth NN ø8 48 P Q QQ R U SS Z ZZ ,, 2, 3,, 4, 0 0, 70, , M4 x 0.7 thread depth ø M4 x M3 x 0. 7 thread depth 7 thread depth 4. 2-M x M4 x thread depth 8 thread depth V X M3 x 0. x 0l M x 0.8 x 0l Y M x 0.8 x l M x.0 x l

35 Dual Rod Cylinder: Basic Type Series CXS Dimensions: ø, ø2, B D Y (Hexagon socket headset screw) Stroke I J K L ZZ SS Z M MX G±0.2 (G) H P MY NN.3 CY E F (Through-hole) N OO (Hexagon bolt), PP (Hexagon nut) X (Hexagon socket head cap screw) (L) (Z) V (Opposite side: Same) MG CX TT T QQ R Q U - N (I) (L) (Z) UU (Piping port) (Opposite side: Same) W C (G) B C D E F G H I J K L M N NN OO P CXS CXS2 CXS M x M x.0 2-M x ø. through 2-ø9. counterbore depth.3 2-ø.9 through 2-ø counterbore depth.3 2-ø.9 through 2-ø counterbore depth.3 2-M4 x 0.7 thread depth 2-M x 0.8 thread depth 7. 2-M x 0.8 thread depth 8 ø0 ø2 ø M x.0 x 8.l M x.0 x 8.l M8 x.2 x 23l CXS CXS2 CXS32 Dimensions by Stroke Symbol SS Z ZZ 0,,, 3,, 0, 70, 7, , 2 4, 0 80, 90, CXS CXS CXS Stroke PP M x.0 M x.0 M8 x.2 Q QQ R T TT U UU V M x 0.8 thread depth 4. 4-Rc /8 thread depth. 4-Rc /8 thread depth. 8-M4 x 0.7 thread depth. 8-M x 0.8 thread depth 7. 8-M x 0.8 thread depth 7. W 2-M x.0 thread depth 0 2-M8 x.2 thread depth 2 2-M8 x.2 thread depth 2 X M x.0 x 2l M x.0 x 4l M8 x.2 x l Y M8 x.2 x l M8 x.2 x l M0 x. x 8l

36 Series CXS Proper uto Switch Mounting Position (Detection at stroke end) Electrical entry direction: Inward B Electrical entry direction: Outward D Bore size Z7/Z8, Y7W Y, Y7 C D. (0) 0. ( ) 8. (7) 3. (2) 2. (2) 0. ( ) 34 (32.) 3 (.) 34 (32.) (3.) 44 (42.) (3.) Dimensions for Mounting of uto Switch Mounting of uto Switch B Y, Y, Y7 (Solid state switch) Y, Y7V Y7WV C D C Z7/Z8 (Reed switch) Y7BL D Lead wire entry is inward prior to shipment. Note ) Negative figures in the table D indicate an auto switch is mounted inward from the edge of the cylinder body. Note 2) ( ): Denotes the dimensions of Z73. When mounting and securing auto switches, they should be inserted into the cylinder s switch mounting rail from the direction shown in the drawing below. fter setting in the mounting position, use a flat head watchmakers screwdriver to tighten the set screw that is included. Note) When tightening an auto switch mounting screw, use a watchmakers screwdriver with a handle of approximately to mm in diameter. lso, tighten with a torque of about 0.0 to 0. N m. s a guide, turn about 90 past the point at which tightening can first be felt. C M2. x 4l (Included with auto switch) Operating Range uto switch model Z7/Z80 Y9, Y9 Y7P/Y7PV Y7W/Y7WV Y7BL Dimension Y9/Y7P/Y9B Y9/Y7PV/Y9B Y7NWV/Y7PWV/Y7BWV Y7NW/Y7PW/Y7BW Y7BL Z7, Z8 Bore size Since this is a guideline including hysteresis, not meant to be guaranteed. (assuming approximately ±% dispersion.) There may be the case it will vary substantially depending on an ambient environment. uto switch model Bore size Caution. void proximity to magnetic objects shown in the drawing below. If the clearance is less than the values noted in the table below, the auto switch may not function properly. uto switch Bore size X Other than the applicable auto switches listed in How to Order, the following auto switches can be mounted. For detailed specifications, refer to page 8--. Electrical Type entry (Fetching direction) Features Reed switch Z80 Grommet (In-line) Without indicator light Normally closed (NC = b contact), solid state switch (Y7G/Y7H type) are also available. For details, refer to page

37 Dual Rod Cylinder: With ir Cushion Series CXS ø, ø2, Bore size 2, 32 M L CXS M Bearing type Slide bearing Ball bushing bearing Bore size/stroke Stroke, 2,, 3,, 4, 0, 0, 70, 7, 80, 90, 00 2,, 3,, 4, 0, 0, 70, 7, 80, 90, 00 How to Order Thread type Symbol Nil TN TF Type M Rc NPT G Bore size ø 2, Y7BW S ir cushion Number of auto switches (No. of auto switch) Nil S n uto switch 2 pcs. pc. n pcs. Nil Without auto switch (Built-in magnet) For the applicable auto switch model, refer to the table below. uto switches are shipped together, (but not assembled). MX MY CY MG CX - pplicable uto Switch/Refer to page 8-- for further information on auto switches. Type Reed switch Solid state switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) Electrical entry Grommet Grommet Indicator light Yes Yes Wiring (Output) Load voltage DC 3-wire (NPN equivalent) V 2-wire 3-wire (NPN) 3-wire (PNP) 24 V 2 V V, 2 V 2-wire 2 V 3-wire (NPN) 3-wire (PNP) 24 V V, 2 V 2-wire 2 V C uto switch model Perpendicular In-line Z7 00 V Y9 Y7PV Y9B Y7NWV Y7PWV Y7BWV Z73 Y9 Y7P Y9B Y7NW Y7PW Y7BW Y7B Lead wire length (m) 0. (Nil) 3 (L) (Z) Pre-wire connector pplicable load IC circuit Relay, PLC IC circuit IC circuit Relay, PLC Lead wire length symbols: 0. m Nil (Example) Y9 3 m L (Example) Y9L m Z (Example) Y9Z Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wire connector, refer to page Solid state switches marked with are produced upon receipt of order

38 Series CXS Caution Bore size Piston speed (mm/s) 0 to to 00 0 to 00 llowable kinetic energy (J) Selection. Operate the cylinder until the stroke end. If the stroke is restricted by the external stopper and clamp workpiece, effective cushioning and noise reduction will not be achieved. 2. djust the cushion needles to absorb the kinetic energy during the cushion stroke so that excessive kinitic energy does not remain when the piston reaches the stroke end. If the piston reaches the stroke end with excessive kinetic energy remaining (more than the values given in table () below) due to an improper adjustment, excessive impact will occur, causing damage to machinery. Table () llowable Kinetic Energy at Piston Impact Cushion Needle djustment Caution Bore size Rotations Precautions Be sure to read before handling. For Safety Instructions and Common Precautions, refer to pages to Keep the adjusting range for the cushion needle between the fully closed position and the rotations shown below rotations or less 3 rotations or less Use a 3 mm flat head watchmakers screwdriver to adjust the cushion needles to the fully closed position, as this will cause damage to the seals. The adjusting range for the cushion needles must be between the fully closed position and the open position ranges indicated in the table above. retaining mechanism prevents the cushion needles from slipping out; however, they may spring out during operation if they are rotated beyond the ranges shown above. Precautions for selection standard, mounting, piping, and operating environment are same as for the standard series. Specifications Bore size 2 32 Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Note) Piston speed Port size M x 0.8 ir (Non-lube).0 MPa 0.7 MPa 0. MPa 0 to 0 C (No freezing) 0 to 000 mm/s Rc /8 (NPT /8, G /8) Bearing type Cushion Slide bearing, Ball bushing bearing (Same dimensions for both) ir cushion (Both ends) Note) The maximum piston speed shown in the table above is for extension. The maximum piston speed for retraction is approximately 70% that of extension. Cushion mechanism Bore size 2 32 Standard Stroke CXS CXS2 CXS32 Theoretical Output CXS CXS2 CXS32 Weight CXSM- CXSL- CXSM2- CXSL2- CXSM32- CXSL32- Rod size Effective cushion length Operating direction OUT IN OUT IN OUT IN Standard stroke, 2,, 3,, 4, 0, 0, 70, 7, 80, 90, 00 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2 ) Standard stroke bsorbable kinetic energy (J) ,, 3,, 4, 0, 0, 70, 7, 80, 90, 00 Piston area (mm 2 ) (N) Operating pressure (MPa) (kg)

39 Dual Rod Cylinder: With ir Cushion Series CXS Construction CXSM/With air cushion CXSL/With air cushion! i!0 Component Parts: CXSM No. q w e r t y u @4 Housing Replacement Parts: Seal Kit Bore size 2 32 Description Piston rod Piston rod B Rod cover Head cover Plate Piston Piston B Bumper B Magnet Bumper bolt Hexagon nut Bumper Hexagon socket head cap screw Hexagon socket head set screw Snap ring Steel ball Piston seal Rod seal O-ring O-ring Cushion needle Check seal retainer Check seal Needle gasket Check gasket!4 ye!3!2 qr o ie!!4 r ty! q Kit no. CXS-PS CXS2-PS CXS32-PS Material Carbon steel Carbon steel luminum bearing alloy Polyurethane Magnetic material Carbon steel Carbon steel Polyurethane Chromium steel Chromium steel Stainless steel Copper Note Hard anodized Hard chrome plated Hard chrome plated Electroless nickel plated Glossy, self-coloring Chromated Chromated Set of Close-up of Component Parts: CXSL No. q w e r t y u @8 Housing Description Piston rod Piston rod B Rod cover Ball bushing Bumper holder Head cover Plate Piston Piston B Bumper B Magnet Bumper bolt Hexagon nut Bumper Hexagon socket head cap screw Hexagon socket head set screw Snap ring Steel ball Piston seal Rod seal O-ring O-ring Cushion needle Check seal retainer Check seal Needle gasket Check gasket Material luminum bearing alloy Synthetic resin Polyurethane Magnetic material Carbon steel Carbon steel Polyurethane Chromium steel Chromium steel Stainless steel Close-up of Hard anodized Hard chrome plated Hard chrome plated Electroless nickel plated Glossy, self-coloring Chromated Chromated MX MY CY MG CX

40 Series CXS Dimensions: ø cushion needle 2-M x 0.8 thread depth 4. (Piping port) S ZZ 2 23 M8 x.2 x l (Hexagon socket head set screw) 2 2 SS Z (Steel ball) 0 ± M x 0.8 (Through-hole) M x.0 x 2l (Hexagon socket head cap screw) 2-M4 x 0.7 thread depth M x.0 x 8.l, M x.0 (Hexagon bolt) (Hexagon nut).3 2-ø. through 2-ø9. counterbore depth.3 (Z) 4-M4 x 0.7 thread depth M4 x 0.7 thread depth () (Z) 2-M x.0 thread depth 0 0 ± ± 0.2 (4.). Part no. CXS- CXS-2 CXS- CXS-3 CXS- CXS-4 CXS-0 CXS-0 CXS-70 CXS-7 CXS-80 CXS-90 CXS-00 S SS ZZ Z 0 ø

41 Dual Rod Cylinder: With ir Cushion Series CXS Dimensions: ø cushion needle MX Note) 2-Rc /8 thread depth. (Piping port) (2.) 0 ± M x.0 (Through-hole) thread depth 7. M x.0 x 4l (Hexagon socket head cap screw) (Z) 4 4-M x 0.8 thread depth 7. (Steel ball) M x 0.8 thread depth 7. () (Z) 2-M8 x.2 thread depth 2 0 ± 0.2 M8 x.2 x l (Hexagon socket head set screw) 0 ± M x 0.8 S 2 2 ZZ Z SS M x.0 x 8.l : M x.0 (Hexagon bolt) (Hexagon nut) 2-ø.9 through 2-ø counterbore depth.3 MY CY MG CX - ø2 Part no. CXS2-2 CXS2- CXS2-3 CXS2- CXS2-4 CXS2-0 CXS2-0 CXS2-70 CXS2-7 CXS2-80 CXS2-90 CXS2-00 S SS ZZ Z 0 Note) For port threads TN and TF, only the piping port type varies

42 Series CXS Dimensions: cushion needle S ZZ Note) 2-Rc /8 thread depth. (Piping port) 4 SS 38 3 M0 x. x 8l (Hexagon socket head set screw) 8 Z (Steel ball) 7 ± M x 0.8 thread depth 8 2-M x 0.8 thread depth 8 8 () (Z) 2-M8 x.2 thread depth 2 ø 7 ± M x.0 (Through-hole) M8 x.2 x l (Hexagon socket head cap screw) 2-ø.9 through 2-ø counterbore depth.3 M8 x.2 x 23l, M8 x.2 (Hexagon bolt) (Hexagon nut) (Z) 4-M x 0.8 thread depth T ± 0.2 () 8 Part no. CXS32-2 CXS32- CXS32-3 CXS32- CXS32-4 CXS32-0 CXS32-0 CXS32-70 CXS32-7 CXS32-80 CXS32-90 CXS32-00 S SS ZZ Z 0 70 Note) For port threads TN and TF, only the piping port type varies

43 Dual Rod Cylinder: With ir Cushion Series CXS Proper uto Switch Mounting Position (Detection at stroke end) Electrical entry direction: Inward B Electrical entry direction: Outward D C MX MY CY MG CX Bore size B Z7/Z8, Y7W Y, Y7 C 3. (3) 38 (3.) 48. (47) D 2. () 4 (2.). (4) Y, Y7V Y7WV Y7BL C D C D s for auto switch mounting dimensions, auto switch mounting method and its operating range, those are the same as basic type. Refer to page

44 Dual Rod Cylinder: With End Lock For Retraction Side Series CXS ø, ø0, ø, ø, ø2, CXS M 0 How to Order 0 R Y7BW S M L Bearing type Slide bearing Ball bushing bearing Number of auto switches Nil S n 2 pcs. pc. n pcs. Bore size, 0,, 2, 32 Bore size/stroke Stroke 0,,,, 0 0,,,, 0, 7, 00 uto switch Nil Without auto switch (Built-in magnet) For the applicable auto switch model, refer to the table below. uto switches are shipped together, (but not assembled). With end lock for retraction side pplicable uto Switch/Refer to page 8-- for further information on auto switches. Type Reed switch Solid state switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) Electrical entry Grommet Grommet Indicator light Yes Yes Wiring (Output) Load voltage DC 3-wire (NPN equivalent) V 2-wire 3-wire (NPN) 3-wire (PNP) 24 V 2 V V, 2 V 2-wire 2 V 3-wire (NPN) 3-wire (PNP) 24 V V, 2 V 2-wire 2 V C uto switch model Perpendicular In-line Z7 00 V Y9 Y7PV Y9B Y7NWV Y7PWV Y7BWV Z73 Y9 Y7P Y9B Y7NW Y7PW Y7BW Y7B Lead wire length (m) 0. (Nil) 3 (L) (Z) Pre-wire connector pplicable load IC circuit Relay, PLC IC circuit IC Relay, circuit PLC Lead wire length symbols: 0. m Nil (Example) Y9 3 m L (Example) Y9L m Z (Example) Y9Z Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wire connector, refer to page Solid state switches marked with are produced upon receipt of order

45 Dual Rod Cylinder: With End Lock For Retracting Side Series CXS Caution Precautions Be sure to read before handling. For Safety Instructions and Common Precautions, refer to pages to Mounting Mounting and adjusting. Release the lock when mounting and adjusting the cylinder. n attempt to mount or adjust a cylinder while it is locked can damage the lock. 2. Never adjust the retracting stroke using a bumper bolt or external stopper. The lock will not function. Releasing the lock Do not release the lock while a load is applied to the lock. This will cause a sudden, erratic movement of the cylinder, and create a dangerous condition. Control circuit. To control the end lock cylinder, use a 2 position 4/ port solenoid valve. void using these valves along with a 3 position solenoid valve (especially a closed-center metal seal type). 2. Be sure to supply air and apply back pressure to the retracted end before operation. If air is supplied to the extende end while there is no air inside of the cylinder, it will cause a sudden, erratic movement of the cylinder, and create a dangerous condition. Manual Release Manual release (Non-locking type). Insert the manual lever and screw it into the lock holder assembly. Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Cushion Note ) Port size M x 0.8 Rc /8 Bearing type Slide bearing, Ball bushing bearing (Same dimensions for both) Note) The maximum piston speed shown in the table above is for extension. The maximum piston speed for retraction is approximately 70% that of extension. Lock Specifications Lock specifications Bore size Maximum holding force (N) Manual release Standard Stroke Theoretical Output 0 2 ir (Non-lube).0 MPa 0.7 MPa 0.3 MPa 0 to 0 C (No freezing) to 0 mm/s to 800 mm/s to 700 mm/s to 00 mm/s Bumper is standard on both ends Rear end lock Non-lock type Standard stroke CXS CXS0 0,,,, 0 CXS CXS CXS2 0,,,, 0, 7, 00 CXS32 Strokes which exceed the standard stroke length will be available as special goods. Weight Bore size Rod size Operating Piston area direction (mm 2 ) CXS CXS0 CXS CXS CXS2 CXS OUT OUT OUT OUT OUT OUT IN IN IN IN IN IN Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2 ) 32 (N) Operating pressure (MPa) MX MY CY MG CX - 2. To unlock, pull the manual lever in the direction of the arrow. Release the manual lever to return the cylinder to a ready-to-lock state. 3. The manual lever (ø. x 3l, tip part: M. x 0.3 x 3l) is included with the cylinder. If additional manual levers are required, use the following part number to place an order: CXS0-48BK2777 (for all series). CXSM-R CXSL-R CXSM0-R CXSL0-R CXSM-R CXSL-R CXSM-R CXSL-R CXSM2-R CXSL2-R CXSM32-R CXSL32-R Standard stroke (kg)