Air Cylinder. New RoHS. Series CM2. Female rod end available as standard. Rod end styles suitable for the application can be selected.

Size: px
Start display at page:

Download "Air Cylinder. New RoHS. Series CM2. Female rod end available as standard. Rod end styles suitable for the application can be selected."

Transcription

1 ir Cylinder ø20, ø25, ø32, ø40 New RoS Female rod end available as standard Selectable Rod end styles suitable for the application can be selected. Female thread Male thread Easy fine adjustment of auto switch position Fine adjustment of the auto switch position is possible by simply loosening the screw attached to the auto switch. Transparent switch bracket improves visibility of indicator LED. Fine adjustment of auto switch LED colour indicator Single clevis and trunnion pivot brackets are available. Rotating angle: Max. 202 (ore size 40 mm) Single clevis Max. rotating angle Rod trunnion ead trunnion Screw attached to auto switch Switch bracket 26 Series/ set additionally type: Double rod, Single acting Non-rotating type Direct mount type Direct mount, Non-rotating type : eat resistant cylinder (-X6), Made of stainless steel (-XC6) and Dual stroke cylinder (-XC10, 11) etc. are added. Series CT.EUS UK

2 ir Cylinder New Part numbers with rod end bracket and/or pivot bracket available Not necessary to order a bracket for the applicable cylinder separately Note) Mounting bracket is shipped together with the product, but not assembled. Example) CDM2E20-50Z- N W -M9W Pivot bracket None N Pivot bracket is shipped together with the product, but not assembled. N: Kit of pivot bracket and single clevis Kit of pivot bracket and trunnion Rod end bracket None V Single knuckle joint W Double knuckle joint With rod end bracket V: Single W: Double knuckle joint knuckle joint Various mounting bracket options Suitable mounting brackets can be selected for the installation condition. Improved amount of mounting freedom V: Single knuckle joint E(V): Integral clevis : asic N: Clevis pivot bracket D: Double clevis C: Single clevis G: ead flange L: xial foot N: Pivot bracket W: Double knuckle joint F(FZ): Rod flange Z: oss-cut/asic T: ead trunnion L: xial foot N: Pivot bracket U(UZ): Rod trunnion N: Pivot bracket N: Pivot bracket Easy fine adjustment of auto switch position Fine adjustment of the auto switch set position can be performed by loosening the auto switch attached screw without loosening the auto switch mounting band. Operability improved compared with the conventional auto switch set position adjustment, where the complete switch mounting band requires loosening. Switch bracket Screw attached to auto switch Visibility of the indicator LED improved with the transparent resin switch bracket ( specification) Switch holder uto switch Total length is shortened with boss-cut type. oss for the head cover bracket is eliminated and the total length of cylinder is shortened. Full Length Dimension Comparison (compared to the basic type ()) ø20 13 ø25 13 ø32 13 ø40 16 Mounting oss-cut/asic (Z) oss-cut/rod flange (FZ) oss-cut/rod trunnion (UZ) No environmental hazardous substances used Compliant with EU RoS directive. Lead free bushing is used as sliding material. Specifications, performance and mounting method are same as the existing product. Features 1 uto switch mounting band uto switch mounting screw Grease is selectable. (Option) Grease for food processing equipment (XC85) PTFE grease (X446) Water resistant compact auto switch now available Solid state auto switch D-M9 (V)

3 Stroke Variations ore size Series stroke Series Variations Series -Z -Z For details about the clean series, consult SMC. ore size Variations Series ction Rod Cushion With Clean Page rod boot ir-hydro series Double acting Single rod Rubber bumper ir cushion Page 1 Double acting Double rod Rubber bumper ir cushion Page 20 Single acting Single rod (Spring return/extend) Rubber bumper Page 29 Non-rotating rod K-Z Double acting Single rod Rubber bumper ir cushion Page 43 Double acting Double rod Rubber bumper ir cushion Page 49 Direct mount R-Z Double acting Single rod Rubber bumper ir cushion Page 54 Direct mount, Non-rotating rod RK-Z Double acting Single rod Rubber bumper Page 61 Series Non-rotating rod K Single acting Single rod (Spring return/extend) Rubber bumper Centralized piping P Double acting Single rod Rubber bumper With end lock CM2 Double acting Single rod Rubber bumper ir cushion Locked in head end only Series CM3 Short type CM3 Double acting Single rod Rubber bumper Features 2

4 Combinations of Products and Specifications Series : : : Special product (Please contact SMC for details.) : Not available ( type) Double acting Single acting Single rod Double rod Single rod Rubber ir Rubber ir Rubber Page 1 Page 20 Page 29 Specifications pplicable bore size ø20 to ø40 D uilt-in magnet - J K With rod boot ir-hydro type ø20 to ø Clean series 20- Note 3) Copper Note 2) and Fluorine-free R V Water resistant X6 eat resistant cylinder ( 10 to 150 C) Note 1) X7 Cold resistant cylinder ( 40 to 70 C) Note 1) X9 Low speed cylinder (5 to 50 mm/s) XC3 Special port location XC4 With heavy duty scraper XC5 eat resistant cylinder ( 10 to 110 C) Note 1) XC6 Made of stainless steel XC8 djustable stroke cylinder/djustable extension type XC9 djustable stroke cylinder/djustable retraction type XC10 Dual stroke cylinder/double rod type XC11 Dual stroke cylinder/single rod type XC12 Tandem cylinder ø20 to ø40 XC13 uto switch rail mounting XC20 ead cover axial port XC22 Fluororubber seal XC25 No fixed orifice of connection port XC27 Double clevis and double knuckle joint pins made of stainless steel XC29 Double knuckle joint with spring pin XC35 With coil scraper XC38 Vacuum specification (Rod through-hole) XC52 Mounting nut with set screw XC85 Grease for food processing equipment X446 PTFE grease Note 1) The products with an auto switch are not compatible. Note 2) Copper-free for the externally exposed part Note 3) For details, consult SMC. Series ction/ Type Cushion Page Front matter 1

5 Series K (Not-rotating rod type) R (Direct mount type) RK (Direct mount, Non-rotating rod type) Double acting Double acting Double acting Single rod Double rod Single rod Single rod Rubber ir Rubber ir Rubber ir Rubber Page 43 Page 49 Page 54 Page 61 ø20 to ø40 D - J K Note 3) R V X6 X7 X9 XC3 XC4 XC5 XC6 XC8 XC9 XC10 XC11 XC12 XC13 XC20 XC22 XC25 XC27 XC29 XC35 XC38 XC52 XC85 X446 Direct Mount, Non-rotating Rod Direct Mount Non-rotating Rod Double cting, Double Rod Single cting, Spring Return/Extend Double cting, Double Rod W K KW R RK uto Switch Front matter 2

6 ir Cylinder: Type Series ø20, ø25, ø32, ø40 1 Cylinder stroke (Refer to Strokes on page 2.) With auto switch With auto switch (uilt-in magnet) L F G C D U Pneumatic ir-hydro asic xial foot Rod fl ange ead fl ange Single clevis Double clevis Rod trunnion Type CDM2 ore size mm mm mm mm E C Mounting T ead trunnion E Integral clevis V Integral clevis (90 ) Z oss-cut/asic FZ oss-cut/rod fl ange UZ oss-cut/rod trunnion ow to Order Port thread type Rc TN NPT TF G ir-hydro type: Rc only Cushion Rod boot For female rod end, no rod boot is provided. Rubber bumper ir cushion ir-hydro cylinder: Rubber bumper only Rod end thread Male rod end F Female rod end N V N V Rod end bracket None V Single knuckle joint W Double knuckle joint No bracket is provided for the female rod end type. knuckle joint pin is not provided with the single knuckle joint. Rod end bracket is shipped together with the product, but not assembled. pplicable uto Switches/Refer to the uto Switch Guide for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Electrical entry Indicator light Yes Yes No Yes No Yes No Yes Wiring (Output) None J Nylon tarpaulin K eat resistant tarpaulin Z Z Pivot bracket None N Only for C, T, U, E, V, UZ mounting types. Pivot bracket is shipped together with the product, but not assembled. M9W Load voltage uto switch model Lead wire length [m] DC C Perpendicular In-line 0.5 ( ) 1 (M) 3 (L) Pivot bracket is shipped together with the product, but not assembled. Refer to page 2 for details. Number of auto switches 2 pcs. S 1 pc. n n pcs. uto switch Without auto switch For applicable auto switches, refer to the table below. 5 None (Z) (N) Pre-wired connector pplicable load 3-wire (NPN) M9NV M9N 5 V,12 V Grommet 3-wire (PNP) M9PV M9P IC circuit M9V M9 2-wire 12 V Connector 7C Terminal 3-wire (NPN) 5 V,12 V G39 IC circuit conduit 2-wire 12 V K39 Relay, 3-wire (NPN) 24 V M9NWV M9NW Diagnostic indication 5 V,12 V IC circuit PLC 3-wire (PNP) M9PWV M9PW (2-colour indication) 2-wire 12 V M9WV M9W Grommet 3-wire (NPN) M9NV M9N Water resistant 5 V,12 V IC circuit 3-wire (PNP) M9PV M9P (2-colour indication) 2-wire 12 V M9V M9 With diagnostic output (2-colour indication) 4-wire (NPN) 5 V,12 V 7NF IC circuit 3-wire (NPN equivalent) 5 V 96V 96 IC circuit Grommet 100 V 93V V or less 90V 90 IC circuit 100 V, 200 V 54 Relay, 200 V or less 64 PLC Connector 2-wire 24 V 12 V C73C 24 V or less C80C IC circuit Terminal 33 PLC conduit V, 200 V Relay, DIN terminal 44 PLC Diagnostic indication (2-colour indication) Grommet 59W Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. water-resistant type cylinder is recommended for use in an environment which requires water resistance. Lead wire length symbols: 0.5 m (Example) M9NW Solid state auto switches marked with are produced upon receipt of order. 1 m M (Example) M9NWM Do not indicate suffi x N for no lead wire on the D-3 /44/G39/K39 3 m L (Example) M9NWL models. 5 m Z (Example) M9NWZ None N (Example) 7CN Since there are other applicable auto switches than listed above, refer to page 69 for details. For details about auto switches with pre-wired connector, refer to the uto Switch Guide. The D-9 /M9 auto switches are shipped together, (but not assembled). (owever, only the auto switch mounting brackets are assembled before shipment.)

7 ir Cylinder: Type Series Double acting, Single rod ir cushion Refer to pages 65 to 69 for cylinders with auto switches uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. (For details, refer to pages 71 to 85.) Specifications -X Change of rod end shape -X6 eat resistant cylinder ( 10 to 150 C) -X7 Cold resistant cylinder ( 40 to 70 C) -X9 Low speed cylinder (10 to 50 mm/s) -XC3 Special port location -XC4 With heavy duty scraper -XC5 eat resistant cylinder ( 10 to 110 C) -XC6 Made of stainless steel -XC8 djustable stroke cylinder/djustable extension type -XC9 djustable stroke cylinder/djustable retraction type -XC10 Dual stroke cylinder/double rod type -XC11 Dual stroke cylinder/single rod type -XC12 Tandem cylinder -XC13 uto switch rail mounting -XC20 ead cover axial port -XC22 Fluororubber seal -XC25 No fi xed orifi ce of connection port -XC27 Double clevis and double knuckle pins made of stainless steel -XC29 Double knuckle joint with spring pin -XC35 With coil scraper -XC52 Mounting nut with set screw -XC85 Grease for food processing equipment -X446 PTFE grease Specifications ore size Type Pneumatic ction Double acting, Single rod Fluid ir Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.05 MPa mbient and fluid temperature Without auto switch: 10 C to 70 C (No freezing) With auto switch: 10 C to 60 C Lubrication Not required (Non-lube) +1.4 Stroke length tolerance 0 mm Piston speed 50 to 750 mm/s Cushion Rubber bumper, ir cushion Rubber Male thread 0.27 J 0.4 J 0.65 J 1.2 J llowable bumper Female thread 0.11 J 0.18 J 0.29 J 0.52 J kinetic ir cushion 0.54 J 0.78 J 1.27 J 2.35 J energy Male thread (Effective cushion (11.0) (11.0) (11.0) (11.8) length ) Female thread 0.11 J 0.18 J 0.29 J 0.52 J Operate the cylinder with in the allowable kinetic energy. Strokes ore size 20 Note 1) Intermediate strokes not listed above are produced upon receipt of order. Manufacture of intermediate strokes in 1 mm intervals is possible. (Spacers are not used.) Note 2) When exceeding 300 strokes, the allowable maximum stroke length is determined by the stroke selection table. Option: Ordering Example of Cylinder ssembly Single knuckle joint Cylinder model: CDM2C20-50Z-NV-M9W uto switch stroke Note) Single clevis Pivot bracket Maximum stroke , 50, 75, 100, 125, 150, 200, 250, Mounting C: Single clevis Pivot bracket N: Yes Rod end bracket V: Single knuckle joint uto switch D-M9W: 2 pcs. Pivot bracket, double knuckle joint and auto switch are shipped together with the product, but not assembled. Pivot bracket is available only for C, T, U, E, V, UZ mounting types. No bracket is provided for the female rod end type. Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch 2

8 Series Mounting and ccessories Note 1) Rod end nut is not provided for the female rod end type. Note 2) Two mounting nuts are packaged together. Note 3) Mounting nut is not packaged for the clevis. Note 4) Trunnion nut is packaged for U, T, UZ. Order 2 foots per cylinder. 3 liners are included with a clevis bracket for adjusting the mounting angle. clevis pin and retaining rings (split pins for ø40) are included. 3 ccessories ody (mounted to the body) Mounting: C Pivot bracket symbol: N (1 pc.) Note 3) (1 pc.) (1 pc.) (mounted to the body) (packaged together, but not assembled) Option Mounting nut Note 1) Rod end nut (Male thread) Single clevis Double clevis Note 5) Retaining rings are included. Note 6) pin and retaining rings (split pins for ø40) are included. Note 7) This is the part(s) used to adjust the clevis angle. Mounting quantity can vary. Mounting bracket Min. ore size order q ty Contents (for minimum order quantity) Foot 2 CM-L020 CM-L032 CM-L040 2 foots, 1 mounting nut Flange 1 CM-F020 CM-F032 CM-F040 1 fl ange Single clevis 1 CM-C020 CM-C032 CM-C040 1 single clevis, 3 liners Double clevis (with pin) 1 CM-D020 CM-D032 CM-D040 Note 7) Liner Mounting nut 1 double clevis, 3 liners, 1 clevis pin, 2 retaining rings Trunnion (with nut) 1 CM-T020 CM-T032 CM-T040 1 trunnion, 1 trunnion nut Rod end nut 1 NT-02 NT-03 NT-04 1 rod end nut Mounting nut 1 SN-020 SN-032 SN mounting nut Trunnion nut 1 TN-020 TN-032 TN trunnion nut Single knuckle joint 1 I-020 I-032 I single knuckle joint Double knuckle joint 1 Y-020 Y-032 Y double knuckle joint, 1 clevis pin, 2 retaining rings Clevis pin (Double clevis) 1 CDP-1 CDP-2 1 clevis pin, 2 retaining rings (split pins) Clevis pin (Double knuckle joint) 1 CDP-1 CDP-3 1 clevis pin, 2 retaining rings (split pins) Pivot bracket pin 1 CDP-1 CD-S03 1 pin, 2 retaining rings Clevis pivot bracket pin (For E/V) 1 CD-S02 CD-S03 1 clevis pin, 2 retaining rings Clevis pivot bracket (For E/V) 1 CM-E020 CM-E032 1 clevis pivot bracket, 1 clevis pin, 2 retaining rings Pivot bracket (For C) 1 CM-032 CM pivot brackets (1 of each type) Pivot bracket (For U/T) 1 CM-020 CM-032 CM pivot brackets (1 of each type) Option (Max. 3 pcs.) Note 3) (2 pc.) (1 pc.) Single clevis + Pivot bracket + Pin Mounting: T, U, UZ Pivot bracket symbol: N (1 pc.) Note 4) (1 pc.) Note 3) (2 pc.) (1 pc.) (1 pc.) Trunnion + Pivot bracket Mounting: E Pivot bracket symbol: N (1 pc.) Note 3) (1 pc.) Note 3) (1 pc.) (1 pc.) Integral clevis + Pivot bracket + Pin Mounting: V Pivot bracket symbol: N (1 pc.) Note 3) (1 pc.) Note 3) (1 pc.) (1 pc.) Integral clevis (90 ) + Pivot bracket + Pin Foot Flange Pivot bracket Note 5) Pivot bracket pin Note 5) Double clevis pin Trunnion Mounting nut (For Trunnion) Clevis pivot bracket (E/V) Clevis pivot Note 5) bracket pin (E/V) Mounting asic (Double-side bossed) (1 pc.) (1 pc.) (1 pc.) L xial foot (1 pc.) (1 pc.) Note 2) (1 pc.) (1 pc.) Note 2) (2 pc.) F Rod fl ange (1 pc.) (1 pc.) (1 pc.) (1 pc.) G ead fl ange (1 pc.) (1 pc.) (1 pc.) (1 pc.) C Single clevis (1 pc.) Note 3) (1 pc.) (1 pc.) (Max. 3 pcs.) Note 3) D Double clevis (1 pc.) Note 3) (1 pc.) (1 pc.) (Max. 3 pcs.) Note 3) (1 pc.) U Rod trunnion (1 pc.) Note 4) (1 pc.) (1 pc.) (1 pc.) T ead trunnion (1 pc.) Note 4) (1 pc.) (1 pc.) (1 pc.) E Integral clevis (1 pc.) Note 3) (1 pc.) Note 3) V Integral clevis (90 ) (1 pc.) Note 3) (1 pc.) Note 3) Z oss-cut/asic (1 pc.) (1 pc.) (1 pc.) FZ oss-cut/ Rod fl ange UZ oss-cut/ Rod trunnion Mounting rackets/part No. (1 pc.) (1 pc.) (1 pc.) (1 pc.) (1 pc.) Note 4) (1 pc.) (1 pc.) (1 pc.) Single knuckle joint (Male thread only) Note 6) Double knuckle joint (Male thread only)

9 ir Cylinder: Type Series Mounting rackets, ccessories/material, Surface Treatment Segment Description Material Surface treatment Foot Carbon steel Nickel plating Flange Carbon steel Nickel plating Mounting Single clevis Carbon steel Nickel plating brackets Double clevis Carbon steel Nickel plating Trunnion Cast iron Electroless nickel plating Rod end nut Carbon steel Zinc chromated Mounting nut Carbon steel Nickel plating Trunnion nut Carbon steel Nickel plating Clevis pivot bracket Carbon steel Nickel plating Clevis pivot bracket pin Carbon steel (None) Carbon steel Single knuckle joint ccessories ø40: Free-cutting steel Electroless nickel plating Double knuckle joint e sure to read before handling. Refer to back cover for Safety Instructions. For ctuator and uto Switch Precautions, refer to andling Precaution for SMC Products and the Operation Manual on SMC website, Warning Carbon steel ø40: Cast iron Double clevis pin Carbon steel (None) Double knuckle joint pin Carbon steel (None) Pivot bracket Carbon steel Nickel plating Pivot bracket pin Carbon steel (None) Electroless nickel plating Metallic bronze colour painting for ø40 1. Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fi tting into the port, it is likely to damage the junction part with cover. 2. Operate the cylinder within the specified cylinder speed, kinetic energy and lateral load at the rod end. 3. The allowable kinetic energy is different between the cylinders with male rod end and with female rod end due to the different thread sizes. 4. When female rod end is used, use a washer, etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. 5. Do not apply excessive lateral load to the piston rod. Easy checking method Minimum operating pressure after the cylinder is mounted to the equipment [MPa] = Minimum operating pressure of cylinder [MPa] + {Load mass [kg] x Friction coeffi cient of guide/sectional area of cylinder [mm 2 ]} If smooth operation is confi rmed within the above value, the load on the cylinder is the resistance of the thrust only and it can be judged as having no lateral load. 6. Do not operate with the cushion needle in a fully closed condition. Using it in the fully closed state will cause the cushion seal to be damaged. When adjusting the cushion needle, use the exagon wrench key: nominal size Do not open the cushion needle wide excessively. If the cushion needle were set to be completely wide (more than 3 turns from fully closed), it would be equivalent to the cylinder with no cushion, thus making the impacts extremely high. Do not use it in such a way. esides, using with fully open could give damage to the piston or cover. Weights Precautions Operating Precautions [kg] ore size asic xial foot Flange Integral clevis asic Single clevis weight Double clevis Trunnion oss-cut/asic oss-cut/flange oss-cut/trunnion dditional weight per 50 mm of stroke Option bracket Clevis bracket (with pin) Single knuckle joint Double knuckle joint (with pin) Pivot bracket Pivot bracket pin Calculation: (Example) L32-100Z asic weight 0.44 (Foot, ø32) dditional weight 0.08/50 stroke Cylinder stroke 100 stroke x 100/50 = 0.60 kg Caution 1. Not able to disassemble. Cover and cylinder tube are connected to each other by caulking method, thus making it impossible to disassemble. Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (retaining ring plier: tool for installing a type C retaining ring). Even if a proper tool is used, it is likely to infl ict damage to a human body or peripheral equipment, as a retaining ring may be fl own out of the tip of a plier. e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed fi rmly into the groove of rod cover before supplying air at the time of installment. 3. Do not touch the cylinder during operation. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 4. Do not use an air cylinder as an air-hydro cylinder. If it uses turbine oil in place of fl uids for cylinder, it may result in oil leakage. 5. The oil stuck to the cylinder is grease. 6. The base oil of grease may seep out. The base oil of grease in the cylinder may seep out of the tube, cover, crimped part or rod bushing depending on the operating conditions (ambient temperature 40 C or more, Pressurised condition, low frequency operation). 7. When rod end female thread is used, use a thin wrench when tightening the piston rod. 8. Combine the rod end section, so that a rod boot might not be twisted. If a rod boot is installed with being twisted when installing a cylinder, it will cause a rod boot to fail during operation. 4 Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch

10 Series ir-hydro Clean Series Mounting style ore size Stroke Rod boot Z 10- Mounting style ore size Stroke Z ir-hydro low hydraulic pressure cylinder used at a pressures of 1.0 MPa or below. Through the concurrent use of the CC series air-hydro unit, it is possible to operate at a constant or low speeds or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve. Clean Series (With relief port) The type which is applicable for using inside the clean room graded Class 100 by making an actuator s rod section a double seal construction and discharging by relief port directly to the outside of clean room. Specifications Type Fluid ction ore size Proof pressure Max. operating pressure Min. operating pressure Piston speed mbient and fluid temperature Stroke length tolerance Cushion Mounting ir-hydro Turbine oil Double acting single rod ø20, ø25, ø32, ø MPa 1.0 MPa 0.18 MPa 15 to 300 mm/s +5 to +60 C mm Rubber bumper ( equipment) asic, xial foot, Rod flange, ead fl ange, Single clevis, Double clevis, Rod trunnion, ead trunnion, Integral clevis, Integral clevis (90 ), oss-cut uto switch can be mounted. Dimensions are the same as the series standard type. Specifications ction Double acting, Single rod ore size ø20, ø25, ø32, ø40 Max. operating pressure 1.0 MPa Min. operating pressure 0.05 MPa Cushion Rubber bumper, ir cushion Relief port size M5 x 0.8 Piston speed 30 to 400 mm/s Mounting uto switch can be mounted. Construction asic, xial foot, Rod fl ange, ead fl ange, oss-cut port For construction, refer to page 7. Since the dimensions of mounting style is the same as pages 9 to 16, refer to those pages. Relief port ø20, ø25 Relief port port Relief port The above shows the case of rubber bumper. ø32, ø40 5

11 ir Cylinder: Type Series Water Resistant CDM2 Mounting style ore size Port thread type R Stroke Z M9 -XC6 With auto switch (uilt-in magnet) Water resistant cylinder R NR seals (Nitrile rubber) V FKM seals (Fluororubber) Cushion Rubber bumper ir cushion Water resistant 2-colour indication, solid state auto switch Ideal for use in a machine tool environment exposed to coolant mist. lso, applicable for use in an environment with water splashing such as food processing and car wash equipment, etc. Caution Rod seal and scraper is not replaceable. Scraper is press-fi t into the rod cover, thus cannot be replaced. Specifications ction Double acting, Single rod ore size 20, 25, 32, 40 Cushion Rubber bumper, ir cushion uto switch mounting and mounting style XC6: Made of stainless steel Specifi cations other than the above are the same as the standard basic type. Dimensions ø ore size E1 E2 NN1 NN M22 x 1.5 M20 x 1.5 Other dimensions are the same as double acting, single rod, standard type. ( : Same as the standard.) Mounting rackets/part No. Mounting bracket Min. ore size order 20 Description (for min. order) xial foot 2 CM-L020C 2 foots, 1 mounting nut Flange 1 CM-F020C 1 fl ange Trunnion (with nuts) 1 CM-T020C 1 trunnion, 1 trunnion nut ø25 to ø40: Same as the standard type Order 2 foots per cylinder. ø Double cting, Double Rod W K KW RK R Direct Mount Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod uto Switch Direct Mount, Non-rotating Rod 6

12 Series Construction Rubber bumper t i u!7 y qo @C!3!5!4 oss-cut Integral clevis ir-hydro!7 With air cushion!7 Component Parts No. Description Material Note 1 Rod cover luminium alloy nodised 2 ead cover luminium alloy nodised 2 ead cover luminium alloy nodised 2C ead cover C luminium alloy nodised 3 Cylinder tube Stainless steel 4 Piston luminium alloy 5 Piston rod Carbon steel ard chrome plating 6 ushing earing alloy 7 Seal retainer Stainless steel 8 Retaining ring Carbon steel Phosphate coating 9 umper Resin ø25 or larger is 10 umper Resin common. 11 Piston seal NR No. Description Material Note 12 Wear ring Resin 13 Clevis bushing earing alloy 14 Mounting nut Carbon steel Nickel plating 15 Rod end nut Carbon steel Zinc chromated 16 Magnet CDM2 20 to 40- Z 17 Rod seal NR Replacement Part/Seal With Rubber umper/with ir Cushion Part no. No. Description Material Rod seal NR 0Z-PS 5Z-PS CM32Z-PS CM40Z-PS ir-hydro 17 Rod seal NR 20-PS 25-PS 32-PS 40-PS Since the seal kit does not include a grease pack, order it separately. Grease pack part number: GR-S-010 (10 g) 7

13 ir Cylinder: Type Series asic (Double-side ossed) () ore size Stroke Z ø I Width across flats 2 Width across flats G 2 x P (Rc, NPT, G) G 2 x NN N N ød Width across flats K L K F S + Stroke ZZ + Stroke F 2 x øeh8 Effective thread length 2 x FL Double cting, Double Rod W With rod boot 8 l 8 Width across flats 3 With air cushion 45 W W Single cting, Spring Return/Extend J JW oss-cut øe With Rod oot With Rod oot ore size J JW With ir Cushion ore size W f h ZZ + Stroke ZZ + Stroke oss-cut Cushion needle (Width across flats 1.5) Female rod end Female thread Thread depth ZZ + Stroke ore size L 1 2 D E F FL G 1 2 I K K N NN P S ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ h l ZZ 3 e f 1 to to to to to to to to to to to to to to to to to to to to to ore size Stroke ore size Without rod boot ZZ With rod boot 1 to to to to to to to Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. 8 Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod K KW R RK uto Switch

14 Series xial Foot (L) L ore size Stroke Z Width across flats 1 Width across flats K L 1 K F G 2 2 x P (Rc, NPT, G) 2 x NN (Effective thread length 2 x FL) G F 2 x ølc LX LZ L ød Width across flats 2 LT Y Z X Width across flats N S + Stroke LS + Stroke ZZ + Stroke ø 4 x øld X Y With rod boot 8 l 8 Width across flats 3 J øe With air cushion JW 45 Z h ZZ + Stroke W W Cushion needle (Width across flats 1.5) Female rod end 3.5 Female thread Thread depth 1 ZZ + Stroke With Rod oot The bracket is shipped together. 9 ore size L 1 2 D F FL G 1 2 I K K LC LD L LS LT LX LZ N NN P S X Y Z ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ h l Z 3 e 1 to to to to to to to to to to to to to to to to to to to to to ore size Stroke With Rod oot ZZ ore size 1 to to to to to to to 500 J JW Stroke With ir Cushion ore size W Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece.

15 ir Cylinder: Type Series Rod Flange (F) F ore size Stroke Width across flats 2 Width across flats G 2 x P Z (Rc, NPT, G) G NN 4 x øfd Mounting hole C2 ød Width across flats K L K Z FT Width across flats N 1.5 S + Stroke ZZ + Stroke F E ø ø I Effective thread length 2 x FL ø40 FY 2 x øfd Mounting hole FX FZ ø20 to ø32 Double cting, Double Rod W With rod boot J øe 8 l 8 Width across flats 3 oss-cut Single cting, Spring Return/Extend JW With air cushion With Rod oot W With Rod oot ore size J JW With ir Cushion ore size W h ZZ + Stroke oss-cut The bracket is shipped together. W 45 ZZ + Stroke Cushion needle (Width across flats 1.5) Female rod end Female thread Thread depth ZZ + Stroke ore size L 1 2 C2 D E F FL FD FT FX FY FZ G 1 2 I K K N NN P S Z ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ h l ZZ 3 e 1 to to to to to to to to to to to to to to to to to to to to to ore size Stroke ore size Without rod boot ZZ With rod boot 1 to to to to to to to Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. 10 Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod K KW R RK uto Switch

16 Series ead Flange (G) G ore size Stroke C2 2 x øfd Mounting hole Z Width across flats 1 1 NN Effective thread length 2 x FL G 2 x P (Rc, NPT, G) G 2 Width across flats 2 FY ø E ød øi FX FZ ø20 to ø32 4 x øfd Mounting hole ø Width across flats K L K F Width across flats N S + Stroke Z + Stroke ZZ + Stroke FT With rod boot 8 l 8 Width across flats 3 J øe With air cushion 45 JW Cushion needle (Width across flats 1.5) h ZZ + Stroke W f W Female rod end Female thread Thread depth ZZ + Stroke With Rod oot ore size J JW The bracket is shipped together. 11 ore size L 1 2 C2 D E F FL FD FT FX FY FZ G 1 2 I ore size K K N NN P S Z ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ With Rod oot h l ZZ 3 e f 1 to to to to to to to to to to to to to to to to to to to to to ore size Stroke With ir Cushion ore size W Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece.

17 ir Cylinder: Type Series Single Clevis (C) C ore size Stroke øi Z Width across flats 1 1 NN Effective thread length FL G 2 x P (Rc, NPT, G) G øcd CX N N E ød ø Width across flats K L K F S + Stroke 0 + Stroke 0 + Stroke Z +1.2 ZZ +1.2 L U RR øci Double cting, Double Rod W With rod boot J øe 8 l 8 Width across flats 3 Single cting, Spring Return/Extend With air cushion 45 Female rod end JW Cushion needle (Width across flats 1.5) f h ZZ Stroke W W Non-rotating Rod Double cting, Double Rod K KW With Rod oot Female thread Thread depth ZZ Stroke ore size L 1 CI CD CX D E F FL G 1 I K K L N NN P RR S U Z ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ h l Z 3 e f 1 to to to to to to to to to to to to to to to to to to to to to ore size Stroke With Rod oot ZZ ore size 1 to to to to to to to 500 J JW Stroke With ir Cushion ore size W Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. 12 Direct Mount Direct Mount, Non-rotating Rod R RK uto Switch

18 Series Double Clevis (D) D ore size Stroke Z CL øi Width across flats 1 1 NN Effective thread length FL G 2 x P (Rc, NPT, G) øcd hole G xis d N ø E ød øci CX CZ N Width across flats K L K F S + Stroke 0 + Stroke 0 + Stroke Z +1.2 ZZ +1.2 L U RR With rod boot 8 l 8 Width across flats 3 J øe With air cushion JW f h ZZ Stroke 45 W W Female rod end Cushion needle (Width across flats 1.5) With Rod oot 13 Female thread Thread depth ZZ Stroke ore size L 1 CD CI CL CX CZ D E F FL G 1 I K K L N NN P RR S U Z ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ clevis pin and retaining ring (split pins for ø40) are shipped together. h l Z 3 e f 1 to to to to to to to to to to to to to to to to to to to to to ore size Stroke With Rod oot ZZ ore size 1 to to to to to to to 500 J JW Stroke With ir Cushion ore size W Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece.

19 ir Cylinder: Type Series Rod Trunnion (U) U ore size Stroke Z Width across flats 2 Width across flats 1 1 G 2 x P (Rc, NPT, G) G NN øtd Width across flats K ød L K TT Z Width across flats N S + Stroke ZZ + Stroke F øe øi Effective thread length 2 x FL TX TZ øty Double cting, Double Rod W With rod boot J øe 8 l 8 Width across flats 3 oss-cut Single cting, Spring Return/Extend JW With air cushion oss-cut W The bracket is shipped together. Z h ZZ + Stroke W 45 With Rod oot With ir Cushion ore size W ZZ + Stroke Female rod end Cushion needle (Width across flats 1.5) Female Rod End Female thread Thread depth ZZ + Stroke ore size L 1 2 D E F FL G 1 I K K N NN P M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/4 ore size S TD TT TX TY TZ Z ZZ h 3 e ore size 1 to to to to to to to l Z ZZ 1 to to to to to to to to to to to to to to to to to to to to to 500 J JW With Rod oot ore size Stroke ore size Without rod boot ZZ With rod boot 1 to to to to to to to Stroke ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. 14 Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod K KW R RK uto Switch

20 Series ead Trunnion (T) T ore size Stroke Z øtd øty Width across flats 1 øe ød 2 x NN 1 Effective thread length 2 x FL G 2 x P (Rc, NPT, G) øi G Width across flats 2 TX TZ Width across flats K L K F Width across flats N S + Stroke Z + Stroke ZZ + Stroke TT With rod boot 8 l 8 Width across flats 3 J øe JW h ZZ + Stroke f With air cushion 45 W W Female rod end Female thread Thread depth Cushion needle (Width across flats 1.5) ZZ + Stroke ore size L 1 2 D E F FL G 1 I K K N NN P M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/4 ore size S TD TT TX TY TZ Z ZZ With ir Cushion ore size W With Rod oot With Rod oot l Z ZZ ore size 1 to to to to to to to to to to to to to to to to to to to to to 500 J JW Stroke ore size Female Rod End The bracket is shipped together. ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. h 3 e f 1 to to to to to to to Stroke

21 ir Cylinder: Type Series Integral Clevis (E) E ore size Stroke N CX øi L N Z øe ød L 1 K NN F G LZ + Stroke ZZ + Stroke Z + Stroke S + Stroke Effective thread length FL 2 x P (Rc, NPT, G) 2 x øld RR LP L G U øcd øci Double cting, Double Rod W With rod boot LV 8 l Width across flats K Width across flats 1 8 Width across flats 3 With air cushion 45 W LT LF LG LY W Single cting, Spring Return/Extend J JW øe Integral clevis (90 )(V) h ZZ + Stroke f Cushion needle (Width across flats 1.5) Port Female rod end 3.5 Female thread Thread depth 1 The outer dimensions are the same as those for the integral clevis (E). ZZ + Stroke ore size L 1 CD CI CX D E F FL G 1 I K K L N NN M8 x M20 x M10 x M26 x M10 x M26 x M14 x M32 x 2 With ir Cushion With Rod oot ore size P RR S U Z ZZ ore size W h 3 e f 20 1/ ore size 1 to to to to to to to / / / With Rod oot l Z ZZ ore size 1 to to to to to to to to to to to to to to to to to to to to to 500 J JW Stroke Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. Stroke Clevis Pivot racket ore size LD LF LG L LP LT LV LY LZ Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod K KW R RK uto Switch

22 Series Dimensions of ccessories With Single Knuckle Joint Single Knuckle Joint ønd Y (MX) I-020/032 Material: Carbon steel ønd øe1 NX I-040 Material: Free-cutting steel ønd R1 R2 U1 Z (MIN) NX1 1 L U1 R1 NX øe1 1 L U1 ore size ND10 NX1 U1 R2 Y Z M8 x , M10 x M14 x With Double Knuckle Joint pplicable Part no. bore size 1 E1 L ND10 NX R1 U1 I M8 x I , M10 x I M14 x ønd hole 10 xis d9 Y (MX) R2 U2 Z (MIN) NX2 L ore size L ND NX2 R2 U2 Y Z M8 x , M10 x M14 x Double Knuckle Joint Y-020/032 Material: Carbon steel ø ø 2 x ø3 Through hole ø ø ø ønd hole 10 xis d9 Y-040 Material: Cast iron ønd hole 10 xis d9 øe1 NX NZ L øe1 NX NZ L 1 L U1 R1 1 L U1 R1 pplicable Included pin Retaining ring Part no. bore size 1 E1 L L ND NX NZ R1 U1 part number Split pin size Y M8 x CDP-1 Type C 9 for axis Y , M10 x CDP-1 Type C 9 for axis Y M14 x CDP-3 ø3 x 18L knuckle pin and retaining rings (split pins for ø40) are included. Double Clevis Pin/Material: Carbon steel ore size/ø20, ø25, ø32 CDP-1 ore size/ø40 CDP-2 Double Knuckle Pin/Material: Carbon steel ore size/ø20, ø25, ø32 CDP-1 ore size/ø40 CDP-3 ø 2 x ø3 Through hole Retaining ring: Type C9 for axis Retaining rings (split pins for ø40) are included. Split pin: ø3 x 18L Retaining ring: Type C9 for axis Retaining rings (split pins for ø40) are included. Split pin: ø3 x 18L 17

23 Dimensions of ccessories Series Rod End Nut/Material: Carbon steel ød øc ød ød d d C Part no. pplicable bore size C D d NT M8 x NT-03 25, M10 x NT M14 x Mounting Nut/Material: Carbon steel C Part no. pplicable bore size C D d SN M20 x SN , M26 x SN M32 x Trunnion Nut/Material: Carbon steel d Part no. pplicable bore size C D d TN M20 x TN , M26 x TN M32 x 2 10 Clevis Pivot racket (For E(V)) Part no. t m LR LF LE LY pplicable bore size L2 L1 LG ølc hole xis LT L 2 x øld ød ød m t L LV LX Clevis Pivot racket Pin (For E(V)) Note) Retaining rings are included. LT LX LY LV Material: Carbon steel Part no. pplicable bore size L LC LD LE LF LG L LR CM-E020 20, CM-E032 32, Included pin part no. CM-E020 20, CD-S02 CM-E032 32, CD-S03 Note 1) clevis pivot bracket pin and retaining rings are included. Note 2) It cannot be used for the single clevis (C) and the double clevis (D). Material: Carbon steel pplicable Included Part no. Dd9 bore size d L1 L2 m t retaining ring CD-S02 20, Type C 8 for axis CD-S03 32, Type C 10 for axis Double cting, Double Rod W K KW R RK Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount uto Switch Direct Mount, Non-rotating Rod 18

24 Series With Single Clevis CX Z + Stroke øcd LX LZ Rotation ngle ore size , With Rod Trunnion Z + Stroke øcd TX ø x 3.4 Mounting Part no. pplicable bore size CX Z + Stroke CD LX LZ C CM (Single clevis) CM Note) pivot bracket pin and retaining rings are not included with the pivot bracket. With ead Trunnion TX Z + Stroke øcd øcd R11 R11 øcd ø x 3.4 ø LX LX LZ LZ x 3.4 Rod trunnion ead trunnion Mounting Part no. pplicable bore size TX CD LX LZ Z + Stroke Z + Stroke CM U/T CM (Rod/ead trunnion) CM Note) pivot bracket pin and retaining rings are not included with the pivot bracket. Pivot racket Pivot brackets consists of a set of two brackets. Pivot racket Pin (For C) ød ødd ø6.8 R R ø6.8 m t L2 L1 m t 25 17±0.2 R3.4 CD Part no. CM-020 Note 2) 8 CM CM R3.4 17± Note 1) pivot bracket pin and retaining rings are not included with the pivot bracket. Note 2) Only for the trunnion pplicable Included Part no. Dd9 bore size d L1 L2 m t retaining ring 20 to 32 CDP Type C 9 for axis 40 CD-S Type C 10 for axis Note) Retaining rings are included with the pivot bracket pin. 19

25 With auto switch Solid state auto switch Cushion Rubber bumper ir cushion ir-hydro cylinder: Rubber bumper only Type Pneumatic ir-hydro W CDM2W Indicator light Yes Cylinder stroke (Refer to Strokes on page 21.) L L ore size mm mm mm mm Rod end thread Male rod end F Female rod end Rod boot Z M9W Z None J Nylon tarpaulin (One end) JJ Nylon tarpaulin (oth ends) K eat resistant tarpaulin (One end) KK eat resistant tarpaulin (oth ends) For female rod end, no rod boot is provided. With auto switch uto switch (uilt-in magnet) Without auto switch Mounting Port thread type For applicable auto switches, refer to the table below. asic (Double-side bossed) Rc L xial foot TN NPT Number of auto switches F Flange TF G 2 pcs. U Trunnion ir-hydro type: Rc only S 1 pc. n n pcs. (Refer to page 21 for details.) pplicable uto Switches/Refer to the uto Switch Guide for further information on auto switches. Type Special function Load voltage Lead wire length [m] Electrical Wiring uto switch model Pre-wired entry (Output) None DC C connector Perpendicular In-line ( ) (M) (L) (Z) (N) 3-wire (NPN) M9NV M9N 5 V, 12 V Grommet 3-wire (PNP) M9PV M9P IC circuit M9V M9 2-wire 12 V Connector 7C Terminal 3-wire (NPN) 5 V, 12 V G39 IC circuit conduit 2-wire 12 V K39 3-wire (NPN) 24 V M9NWV M9NW Diagnostic indication 5 V, 12 V IC circuit 3-wire (PNP) M9PWV M9PW (2-colour indication) 2-wire 12 V M9WV M9W Water resistant Grommet 3-wire (NPN) 5 V, 12 V M9NV M9N IC circuit (2-colour indication) Reed auto switch ir Cylinder: Type Double cting, Double Rod Series W ø20, ø25, ø32, ø40 3-wire (PNP) M9PV M9P 2-wire 12 V M9V M9 With diagnostic output (2-colour indication) 4-wire (NPN) 5 V, 12 V 7NF IC circuit Yes 3-wire (NPN equivalent) pplicable load 5 V 96V 96 IC circuit Grommet 100 V 93V V or less 90V 90 IC circuit 100 V, 200 V V or less 64 Connector 2-wire 24 V 12 V C73C 24 V or less C80C IC circuit Terminal 33 conduit 100 V, 34 DIN terminal 200 V 44 Diagnostic indication (2-colour indication) Grommet 59W No Yes No Yes No Yes ow to Order Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please contact SMC regarding water resistant types with the above model numbers. Lead wire length symbols: 0.5 m 1 m M 3 m L (Example) M9NW (Example) M9NWM (Example) M9NWL Solid state auto switches marked with are produced upon receipt of order. Do not indicate suffi x N for no lead wire on D-3 /44/G39/K39 models. 5 m Z (Example) M9NWZ None N (Example) 7CN Since there are other applicable auto switches than listed above, refer to page 69 for details. For details about auto switches with pre-wired connector, refer to the uto Switch Guide. The D-9 /M9 auto switches are shipped together, (but not assembled). (owever, only the auto switch mounting brackets are assembled before shipment.) Relay, PLC Relay, PLC PLC Relay, PLC 20 Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch

26 Series W Specifications ore size ction Double acting, Double rod Fluid ir Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.08 MPa Rubber bumper mbient and fluid temperature Without auto switch: 10 C to 70 C (No freezing) With auto switch: 10 C to 60 C Lubrication Not required (Non-lube) Stroke length tolerance mm Piston speed Rubber bumper: 50 to 750 mm/s, ir cushion: 50 to 1000 mm/s Cushion Rubber bumper, ir cushion Rubber Male thread 0.27 J 0.4 J 0.65 J 1.2 J llowable bumper Female thread 0.11 J 0.18 J 0.29 J 0.52 J kinetic ir cushion 0.54 J 0.78 J 1.27 J 2.35 J energy Male thread (Effective cushion (11.0) (11.0) (11.0) (11.8) length ) Female thread 0.11 J 0.18 J 0.29 J 0.52 J Strokes ir cushion (For details, refer to pages 71 to 85.) Specifi cations -X Change of rod end shape -X6 eat resistant cylinder ( 10 to 150 C) -X7 Cold resistant cylinder ( 40 to 70 C) -XC3 Special port location -XC5 eat resistant cylinder ( 10 to 110 C) -XC6 Made of stainless steel -XC13 uto switch rail mounting -XC22 Fluororubber seal -XC29 Double knuckle joint with spring pin -XC35 With coil scraper -XC38 Vacuum (Rod through-hole) -XC52 Mounting nut with set screw -XC85 Grease for food processing equipment -X446 PTFE grease ore size Refer to pages 17 and 18 for accessory bracket, since it is the same as standard type, double acting, single rod. Order 2 foots per cylinder. stroke Note 1) Maximum stroke Note 3) 25, 50, 75, 100, 125, 150, 200, 250, Note 1) Other intermediate strokes can be manufactured upon receipt of order. Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) When exceeding 300 strokes, the allowable maximum stroke length is determined by the stroke selection table. Note 3) When exceeding 500 strokes, please contact SMC. ccessory racket Mounting rackets/part No. Rod oot Material Maximum ambient Rod boot material One side oth sides temperature J JJ Nylon tarpaulin 70 C K KK eat resistant tarpaulin 110 C Maximum ambient temperature for the rod boot itself. Mounting bracket Min. ore size order Description (for min. order) xial foot 2 CM-L020 CM-L032 CM-L040 2 foots, 1 mounting nut Flange 1 CM-F020 CM-F032 CM-F040 1 fl ange Trunnion (with nuts) 1 CM-T020 CM-T032 CM-T040 1 trunnion, 1 trunnion nut Refer to pages 65 to 69 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. 21

27 ir Cylinder: Type Double cting, Double Rod Series W Mounting and ccessories Mounting asic (Double-side bossed) (1 pc.) (2 pcs.) xial foot (2) (2) Flange (1) (2) Trunnion (1) Note 1) (2) Note One/oth side(s) Note 1) Trunnion nuts are attached to the trunnion. Note 2) pin and retaining rings (split pins for ø40) are shipped together with double knuckle joint. Weights ccessory equipment Mounting nut Rod end nut Single knuckle joint Option Double Note 2) knuckle Rod boot joint Pivot bracket [kg] ore size asic (Double-side bossed) asic weight xial foot Flange Trunnion dditional weight per 50 mm of stroke Option Single knuckle joint bracket Double knuckle joint (with pin) Calculation: (Example) WL32-100Z asic weight 0.48 (Foot, ø32) dditional weight 0.13/50 stroke Cylinder stroke 100 stroke x 100/50 = 0.74 kg Precautions e sure to read before handling. Refer to back cover for Safety Instructions. For ctuator and uto Switch Precautions, refer to andling Precaution for SMC Products and the Operation Manual on SMC website, Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod W K KW Warning 1. Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fi tting into the port, it is likely to damage the junction part with cover. 2. Do not operate with the cushion needle in a fully closed condition. Using it in the fully closed state will cause the cushion seal to be damaged. When adjusting the cushion needle, use the exagon wrench key: nominal size Do not open the cushion needle wide excessively. If the cushion needle were set to be completely wide (more than 3 turns from fully closed), it would be equivalent to the cylinder with no cushion, thus making the impacts extremely high. Do not use it in such a way. esides, using with fully open could give damage to the piston or cover. 4. Operate the cylinder within the specified cylinder speed, kinetic energy and lateral load at the rod end. 5. The allowable kinetic energy is different between the cylinders with male rod end and with female rod end due to the different thread sizes. 6. When female rod end is used, use a washer, etc. to prevent the contact part at the rod end from being deformed depending on the material of the work piece. 7. Do not apply excessive lateral load to the piston rod. Easy checking method Minimum operating pressure after the cylinder is mounted to the equipment [MPa] = Minimum operating pressure of cylinder [MPa] + {Load weight [kg] x Friction coefficient of guide/sectional area of cylinder (mm 2 )} If smooth operation is confi rmed within the above value, the load on the cylinder is the resistance of the thrust only and it can be judged as having no lateral load. Operating Precautions Caution 1. Not able to disassemble. Cover and cylinder tube are connected to each other by caulking method, thus making it impossible to disassemble. Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (retaining ring plier: tool for installing a type C retaining ring). Even if a proper tool is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier. e much careful with the popping of a retaining ring. e-sides, be certain that a retaining ring is placed fi rmly into the groove of rod cover before supplying air at the time of installment. 3. Do not touch the cylinder during operation. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 4. Do not use an air cylinder as an air-hydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 5. Combine the rod end section, so that a rod boot might not be twisted. If a rod boot is installed with being twisted when installing a cylinder, it will cause a rod boot to fail during operation. 6. The base oil of grease may seep out. The base oil of grease in the cylinder may seep out of the tube, cover, or crimped part depending on the operating conditions (ambient temperature 40 C or more, pressurised condition, low frequency operation). 7. The oil stuck to the cylinder is grease. 8. When rod end female thread is used, use a thin wrench when tightening the piston rod. 22 Direct Mount Direct Mount, Non-rotating Rod R RK uto Switch

28 Series W ir-hydro Clean Series W Mounting style ore size Stroke Rod boot Z 10-W Mounting style ore size Stroke Z ir-hydro low hydraulic pressure cylinder used at a pressures of 1.0 MPa or below. Through the concurrent use of the CC series air-hydro unit, it is possible to operate at a constant or low speeds or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve. Clean Series (With relief port) The type which is applicable for using inside the clean room graded Class 100 by making an actuator s rod section a double seal construction and discharging by relief port directly to the outside of clean room. Specifications Type Fluid ction ore size Proof pressure Max. operating pressure Min. operating pressure Piston speed mbient and fluid temperature Thread tolerance Stroke length tolerance Cushion Mounting uto switch can be mounted. ir-hydro type Turbine oil Double acting, Double rod ø20, ø25, ø32, ø MPa 1.0 MPa 0.18 MPa 15 to 300 mm/s +5 to +60 C mm Rubber bumper ( equipment) asic, xial foot, Flange, Trunnion Specifications ction Double acting, Double rod ore size ø20, ø25, ø32, ø40 Max. operating pressure 1.0 MPa Min. operating pressure 0.08 MPa Cushion Rubber bumper Relief port size M5 x 0.8 Piston speed 30 to 400 mm/s Mounting asic, xial foot, Flange uto switch can be mounted. Construction For construction, refer to page 24. Since the dimensions of mounting style is the same as pages 26 to 28, refer to those pages. port Relief port ø20, ø25 port Relief port Relief port ø32, ø40 23

29 ir Cylinder: Type Double cting, Double Rod Series W Construction Rubber bumper u y!5 t q r w i e!2!3!4 o!5!1!0 Double cting, Double Rod W ir-hydro!5!5 Single cting, Spring Return/Extend With air cushion!5!5 Non-rotating Rod Double cting, Double Rod K KW Component Parts No. Description Material Note 1 Rod cover luminium alloy nodised 2 Cylinder tube Stainless steel 3 Piston luminium alloy 4 Piston rod Carbon steel ard chrome plating 5 ushing earing alloy 6 Seal retainer Stainless steel 7 Retaining ring Carbon steel Phosphate coating 8 umper Resin 9 umper Resin 10 Mounting nut Carbon steel 11 Rod end nut Carbon steel 12 Piston seal NR Nickel plating 13 Piston gasket NR Zinc chromated 14 Magnet CDM2W 20 to 40- Z 15 Rod seal NR Replacement Part/Seal With Rubber umper/with ir Cushion Part no. No. Description Material Rod seal NR 0Z-PS 5Z-PS CM32Z-PS CM40Z-PS ir-hydro No. Description Material Part no Rod seal NR 20-PS 25-PS 32-PS 40-PS Since the seal kit does not include a grease pack, order it separately. Grease pack part number: GR-S-010 (10 g) Direct Mount Direct Mount, Non-rotating Rod R RK uto Switch 24

30 Series W asic (Double-side ossed) () W ore size Stroke øi Width across flats 2 Width across flats 1 Z 1 2 G Effective thread length 2 x 2 x P FL (Rc, NPT, G) G 2 x NN Width across flats K N ød 2 x øeh8 ød N Width across flats K L K F S + Stroke ZZ + 2 x Stroke F + Stroke K L With rod boot (One side) 8 l 8 Width across flats 3 J øe With rod boot (oth sides) JW f h ZZ + 2 x Stroke Width across flats 3 Width across flats 3 J øe øe 45 JW With air cushion Cushion needle (Width across flats 1.5) W 8 h l 8 f ZZ + 2 x Stroke W 8 f l + Stroke 8 h + Stroke Cushion needle (Width across flats 1.5) 45 Female rod end 25 Female thread Thread depth ZZ + 2 x Stroke ore size L 1 2 D E F FL G 1 2 I K K N NN P S ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ With Rod oot ore size 3 e f h l ZZ (oth sides) 1 to to to to to to to to to to to to to to to With Rod oot With ir Cushion Female Rod End ore size ZZ (One side) ore size W ore size 1 ZZ J JW 1 to to to to to M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece.

31 ir Cylinder: Type Double cting, Double Rod Series W xial Foot (L) WL ore size Stroke Width across flats K Width across flats 1 L 1 Z K F 2 G 2 x P (Rc, NPT, G) G F + Stroke 2 x NN K Effective thread length 2 x FL L Width across flats K 2 x ølc LX LZ L ød Width across flats 2 LT Z Y X Width across flats N S + Stroke LS + Stroke ZZ + 2 x Stroke X øi 4 x øld Y Z + Stroke ød Double cting, Double Rod W With air cushion 45 W W Single cting, Spring Return/Extend Cushion needle (Width across flats 1.5) Female rod end 3.5 Female thread Thread depth 1 With ir Cushion ore size W ZZ + 2 x Stroke ore size L 1 2 D F FL G 1 2 I K K LC LD L LS LT LX LZ N NN P S X Y Z ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. In the case of with rod boot, refer to basic type on page 25 and f dimension on page 9. The bracket is shipped together. Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod K KW R RK uto Switch 26

32 Series W Flange (F) WF ore size Stroke Z Width across flats K Width across flats 1 1 Width across flats K Width across flats 2 Effective thread length 2 x FL 2 G 2 x P (Rc, NPT, G) G 2 x NN 4 x øfd Mounting hole 2 x øfd Mounting hole C2 ød øi øe ød FY L K ø40 Z FT Width across flats N ø20 to ø32 S + Stroke ZZ + 2 x Stroke F + Stroke K L FX FZ With air cushion W W 45 Cushion needle (Width across flats 1.5) Female rod end Female thread Thread depth ZZ + 2 x Stroke ore size L 1 2 C2 D E F FD FL FT FX FY FZ G 1 2 I K K M8 x M10 x M10 x M14 x 1.5 ore size N NN P S Z ZZ M20 x 1.5 1/ M26 x 1.5 1/ M26 x 1.5 1/ M32 x 2 1/ In the case of with rod boot, refer to basic type on page 25 and f dimension on page 10. The bracket is shipped together. With ir Cushion ore size W Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. 27

33 ir Cylinder: Type Double cting, Double Rod Series W Trunnion (U) WU ore size Stroke Width across flats 2 Width across flats 1 1 G Z 2 x P (Rc, NPT, G) G 2 x NN Width across flats K ød Width across flats K With air cushion L K Z TT Width across flats N S + Stroke ZZ + 2 x Stroke F øe øi Effective thread length 2 x FL K + Stroke L ød TX TZ øtd øty Cushion needle (Width across flats 1.5) Double cting, Double Rod Single cting, Spring Return/Extend W Female rod end W Female thread Thread depth 1 W 45 Non-rotating Rod Double cting, Double Rod K KW 3.5 ore size TT TX TY TZ Z ZZ In the case of with rod boot, refer to basic type on page 25 and f dimension on page 14. The bracket is shipped together. ZZ + 2 x Stroke ore size L 1 2 D E F FL G 1 I K K N NN P S TD M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ With ir Cushion ore size W Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. Direct Mount Direct Mount, Non-rotating Rod R RK uto Switch 28

34 ir Cylinder: Type Single cting, Spring Return/Extend Series ø20, ø25, ø32, ø40 ow to Order L F G C D U asic (Double-side bossed) xial foot Rod fl ange ead fl ange Single clevis Double clevis Rod trunnion With auto switch Mounting T ead trunnion E Integral clevis V Integral clevis (90 ) Z oss-cut basic FZ oss-cut rod fl ange UZ oss-cut rod trunnion L 32 CDM2 L Cylinder stroke (Refer to Strokes on page 30.) S S Rod end thread Male rod end F Female rod end Z Z (Refer to page 30 for details.) M9W 29 With auto switch (uilt-in magnet) ore size ction Number of mm S Single acting, Spring return auto switches mm T Single acting, Spring extend 2 pcs mm S 1 pc. uto switch mm n n pcs. Without auto switch For applicable auto switches, refer to the table below. pplicable uto Switches/Refer to the uto Switch Guide for further information on auto switches. Type Special function Solid state auto switch Reed auto switch Electrical entry Indicator light Yes Wiring (Output) Load voltage DC C Lead wire length [m] uto switch model Pre-wired None connector Perpendicular In-line ( ) (M) (L) (Z) (N) M9NV M9N 3-wire (NPN) 5 V, 12 V Grommet 3-wire (PNP) M9PV M9P IC circuit M9V M9 2-wire 12 V Connector 7C Terminal 3-wire (NPN) 5 V, 12 V G39 IC circuit conduit 2-wire 12 V K39 3-wire (NPN) 24 V M9NWV M9NW Diagnostic indication 5 V, 12 V IC circuit 3-wire (PNP) M9PWV M9PW (2-colour indication) 2-wire 12 V M9WV M9W Water resistant Grommet 3-wire (NPN) M9NV M9N 5 V, 12 V (2-colour 3-wire (PNP) M9PV M9P IC circuit indication) 2-wire 12 V M9V M9 With diagnostic output (2-colour indication) 4-wire (NPN) 5 V, 12 V 7NF IC circuit Yes 3-wire (NPN equivalent) pplicable load 5 V 96V 96 IC circuit Grommet 100 V 93V V or less 90V 90 IC circuit 100 V, 200 V V or less 64 Connector 2-wiret 24 V 12 V C73C 24 V or less C80C IC circuit Terminal 33 conduit 100 V, 34 DIN terminal 200 V 44 Diagnostic indication (2-colour indication) Grommet 59W No Yes No Yes No Yes Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please contact SMC regarding water resistant types with the above model numbers. Lead wire length symbols: 0.5 m 1 m M (Example) M9NW (Example) M9NWM Solid state auto switches marked with are produced upon receipt of order. Do not indicate suffix N for no lead wire on D-3 /44/G39/K39 models. 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) 7CN Since there are other applicable auto switches than listed above, refer to page 69 for details. For details about auto switches with pre-wired connector, refer to the uto Switch Guide. The D-9 /M9 auto switches are shipped together, (but not assembled). (owever, only the auto switch mounting brackets are assembled before shipment.) Relay, PLC Relay, PLC PLC Relay, PLC

35 ir Cylinder: Type Single cting, Spring Return/Extend Series Spring extend Spring return Specifications ore size ction Single acting, Spring return/single acting, Spring extend Type Pneumatic Cushion Rubber bumper Fluid ir Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating Single acting, Spring return 0.18 MPa pressure Single acting, Spring extend 0.23 MPa mbient and fluid temperature Without auto switch: 10 C to 70 C (No freezing) With auto switch: 10 C to 60 C Lubrication Not required (Non-lube) Stroke length tolerance mm Piston speed 50 to 750 mm/s llowable (Male thread) 0.27 J 0.4 J 0.65 J 1.2 J kinetic energy (Female thread) 0.11 J 0.18 J 0.29 J 0.52 J Double cting, Double Rod Single cting, Spring Return/Extend W Single acting, Spring return, Rubber bumper Single acting, Spring extend, Rubber bumper (For details, refer to pages 71 to 85.) Specifi cations -X Change of rod end shape -XC3 Special port location -XC6 Made of stainless steel -XC13 uto switch rail mounting -XC20 ead cover axial port -XC27 Double clevis and double knuckle pins made of stainless steel -XC29 Double knuckle joint with spring pin -XC52 Mounting nut with set screw -XC85 Grease for food processing equipment Refer to pages 65 to 69 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Strokes ore size stroke 20 25, 50, 75, 100, 125, , 50, 75, 100, 125, , 50, 75, 100, 125, 150, , 50, 75, 100, 125, 150, 200, 250 Note 1) Other intermediate strokes can be manufactured upon receipt of order. Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) Please contact SMC for longer strokes. Mounting racket For the mounting bracket part numbers other than basic type, refer to page 31. ccessory racket Refer to pages 17 and 18 for accessory bracket, since it is the same as standard type, double acting, single rod. Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod K KW R RK uto Switch 30

36 Series Mounting and ccessories ccessories ody Note 1) Rod end nut is not provided for the female rod end type. Note 2) Two mounting nuts are packaged together. Note 3) Mounting nut is not packaged for the clevis. Note 4) Trunnion nut is packaged for U, T, UZ. (mounted to the body) (packaged together, but not assembled) Option Mounting nut Note 1) Rod end nut (Male thread) Single clevis Double clevis Note 7) Liner Mounting nut Foot Flange Pivot bracket Note 5) Pivot bracket pin Note 5) Double clevis pin Note 5) Retaining rings are included. Note 6) pin and retaining rings (split pins for ø40) are included. Note 7) This is the part(s) used to adjust the clevis angle. Mounting quantity can vary. Trunnion Mounting nut (For Trunnion) Clevis pivot bracket (E/V) Clevis pivot Note 5) bracket pin (E/V) Mounting asic (Double-side bossed) (1 pc.) (1 pc.) (1 pc.) L xial foot (1 pc.) (1 pc.) Note 2) (1 pc.) (1 pc.) Note 2) (2 pc.) F Rod fl ange (1 pc.) (1 pc.) (1 pc.) (1 pc.) G ead fl ange (1 pc.) (1 pc.) (1 pc.) (1 pc.) C Single clevis (1 pc.) Note 3) (1 pc.) (1 pc.) (Max. 3 pcs.) Note 3) D Double clevis (1 pc.) Note 3) (1 pc.) (1 pc.) (Max. 3 pcs.) Note 3) (1 pc.) U Rod trunnion (1 pc.) Note 4) (1 pc.) (1 pc.) (1 pc.) T ead trunnion (1 pc.) Note 4) (1 pc.) (1 pc.) (1 pc.) E Integral clevis (1 pc.) Note 3) (1 pc.) Note 3) V Integral clevis (90 ) (1 pc.) Note 3) (1 pc.) Note 3) Z oss-cut/asic (1 pc.) (1 pc.) (1 pc.) FZ oss-cut/ Rod fl ange UZ oss-cut/ Rod trunnion (1 pc.) (1 pc.) (1 pc.) (1 pc.) (1 pc.) Note 4) (1 pc.) (1 pc.) (1 pc.) Single knuckle joint (Male thread only) Note 6) Double knuckle joint (Male thread only) Mounting rackets/part No. Mounting bracket Min. ore size order q ty Contents (for minimum order quantity) Foot 2 CM-L020 CM-L032 CM-L040 2 foots, 1 mounting nut Flange 1 CM-F020 CM-F032 CM-F040 1 fl ange Single clevis 1 CM-C020 CM-C032 CM-C040 1 single clevis, 3 liners Double clevis (with pin) 1 CM-D020 CM-D032 CM-D040 Order 2 foots per cylinder. 3 liners are included with a clevis bracket for adjusting the mounting angle. clevis pin and retaining rings (split pins for ø40) are included. 1 double clevis, 3 liners, 1 clevis pin, 2 retaining rings Trunnion (with nut) 1 CM-T020 CM-T032 CM-T040 1 trunnion, 1 trunnion nut Rod end nut 1 NT-02 NT-03 NT-04 1 rod end nut Mounting nut 1 SN-020 SN-032 SN mounting nut Trunnion nut 1 TN-020 TN-032 TN trunnion nut Single knuckle joint 1 I-020 I-032 I single knuckle joint Double knuckle joint 1 Y-020 Y-032 Y double knuckle joint, 1 clevis pin, 2 retaining rings Clevis pin (Double clevis) 1 CDP-1 CDP-2 1 clevis pin, 2 retaining rings (split pins) Clevis pin (Double knuckle joint) 1 CDP-1 CDP-3 1 clevis pin, 2 retaining rings (split pins) Pivot bracket pin 1 CDP-1 CD-S03 1 pin, 2 retaining rings Clevis pivot bracket pin (For E/V) 1 CD-S02 CD-S03 1 clevis pin, 2 retaining rings Clevis pivot bracket (For E/V) 1 CM-E020 CM-E032 1 clevis pivot bracket, 1 clevis pin, 2 retaining rings Pivot bracket (For C) 1 CM-032 CM pivot brackets (1 of each type) Pivot bracket (For U/T) 1 CM-020 CM-032 CM pivot brackets (1 of each type) 31

37 ir Cylinder: Type Single cting, Spring Return/Extend Series Mounting rackets, ccessories/material, Surface Treatment Segment Description Material Surface treatment Foot Carbon steel Nickel plating Flange Carbon steel Nickel plating Mounting Single clevis Carbon steel Nickel plating brackets Double clevis Carbon steel Nickel plating Trunnion Cast iron Electroless nickel plating Rod end nut Carbon steel Zinc chromated Mounting nut Carbon steel Nickel plating Trunnion nut Carbon steel Nickel plating Pivoting clevis bracket Carbon steel Nickel plating Pivoting clevis bracket pin Carbon steel (None) ccessories Single knuckle joint Double knuckle joint Warning Carbon steel ø40: Free-cutting steel Carbon steel ø40: Cast iron Double clevis pin Carbon steel (None) Electroless nickel plating Electroless nickel plating Metallic bronze colour painted for ø40 Double knuckle joint pin Carbon steel (None) Pivoting bracket Carbon steel Nickel plating Pivoting bracket pin Carbon steel (None) Precautions e sure to read before handling. Refer to back cover for Safety Instructions. For ctuator and uto Switch Precautions, refer to andling Precaution for SMC Products and the Operation Manual on SMC website, Operating Precautions 1. Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fi tting into the port, it is likely to damage the junction part with cover. Caution 1. Not able to disassemble. Cover and cylinder tube are connected to each other by caulking method, thus making it impossible to disassemble. Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (retaining ring plier: tool for installing a type C retaining ring). Even if a proper tool is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be fl own out of the tip of a plier. e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. 3. Do not touch the cylinder during operation. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 4. The oil stuck to the cylinder is grease. 5. The base oil of grease may seep out. Weights Spring Return asic weight Mounting bracket weight Option bracket Calculation: (Example) L32-100SZ (ore size ø32, Foot, 100 stroke) 0.63 (asic weight) (Mounting bracket weight) = 0.79 kg Spring Extend asic weight Mounting bracket weight Option bracket [kg] ore size stroke stroke stroke stroke stroke stroke stroke stroke 1.87 Foot Flange Single clevis Double clevis Trunnion Clevis integrated oss-cut basic oss-cut fl ange oss-cut trunnion Pivot bracket (with pin) Single knuckle joint Double knuckle joint (with pin) ore size stroke stroke stroke stroke stroke stroke stroke stroke 1.72 Foot Flange Single clevis Double clevis Trunnion Clevis integrated oss-cut basic oss-cut fl ange oss-cut trunnion Pivot bracket (with pin) Single knuckle joint Double knuckle joint (with pin) [kg] Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch 32

38 Series Construction Spring return C oss-cut Clevis integrated Spring extend C oss-cut Clevis integrated Component Parts No. Description Material Note 1 Rod cover luminium alloy nodised 2 ead cover luminium alloy nodised 2 ead cover luminium alloy nodised 2C ead cover C luminium alloy nodised 3 Cylinder tube Stainless steel 4 Piston luminium alloy 5 Piston rod Carbon steel ard chrome plating 6 ushing earing alloy 7 Seal retainer Stainless steel 8 Return spring Steel wire Zinc chromated 9 Spring guide luminium alloy Chromated 10 Spring seat luminium alloy Chromated 11 Plug with fixed orifice lloy steel lack zinc chromated 12 Retaining ring Carbon steel Phosphate coating No. Description Material Note 13 umper Resin ø25 or larger is 14 umper Resin common. 15 Piston seal NR 16 Wear ring Resin 17 Clevis bushing earing alloy 18 Mounting nut Carbon steel Nickel plating 19 Rod end nut Carbon steel Zinc chromated 20 Magnet CDM2 20 to 40 - S TZ 21 Rod seal NR Replacement Part/Seal With Rubber umper (Spring extend only) Part no. No. Description Material Rod seal NR 0Z-PS 5Z-PS CM32Z-PS CM40Z-PS Since the seal kit does not include a grease pack, order it separately. Grease pack part number: GR-S-010 (10 g) 33

39 ir Cylinder: Type Single cting, Spring Return/Extend Series asic (Double-side ossed) () ore size Stroke S T Z Spring return øi Width across flats 2 Width across flats Plug with fixed orifice P G 2 x NN N Spring extend oss-cut N Female rod end Spring return øi N N Female thread Thread depth 1 ød Width across flats K Width across flats 1 ød Width across flats K L L K F Width across flats 2 K + Stroke Spring return ZZ + Stroke Spring extend ZZ + 2 x Stroke S + Stroke ZZ + Stroke 2 G P Dimensions by Stroke Stroke 1 to to to to to 250 ore size S ZZ S ZZ S ZZ S ZZ S ZZ F S + Stroke ZZ + 2 x Stroke Spring extend Female thread Thread depth 1 oss-cut 3.5 F Plug with fixed orifice + Stroke 2 x øeh8 Effective thread length 2 x FL F 2 x NN 2 x øeh8 Effective thread length 2 x FL ZZ + Stroke ZZ + 2 x Stroke ore size L 1 2 D E F FL G 1 2 I K K N NN P M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/4 ore size Female Rod End Stroke 1 to to to to to ore size S ZZ S ZZ S ZZ S ZZ S ZZ M4 x M5 x M6 x M8 x Stroke 1 to to to to to 250 ZZ ZZ ZZ ZZ ZZ When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch 34

40 Series xial Foot (L) L ore size Stroke S T Z Spring return Width across flats 2 Width across flats 1 L 1 K F 2 Plug with fixed orifice P G F 2 x NN (Effective thread length 2 x FL) 2 x ølc LX LZ L ød Width across flats K LT Z Y X Width across flats N S + Stroke LS + Stroke ZZ + Stroke øi 4 x øld X Y Spring extend Width across flats 1 L 1 + Stroke K F 2 G P Plug with fixed orifice F 2 x NN (Effective thread length 2 x FL) 2 x ølc LX LZ L ød Width across flats K Width across flats 2 Z + Stroke LT Y X Width across flats N S + Stroke LS + Stroke ZZ + Stroke øi 4 x øld X Y ore size L 1 2 D F FL G 1 2 I K K LC LD L LT LX LZ N NN P X Y Z M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ Dimensions by Stroke Stroke 1 to to to to to 250 ore size LS S ZZ LS S ZZ LS S ZZ LS S ZZ LS S ZZ The bracket is shipped together. Refer to page 34 for female thread dimensions. 35

41 ir Cylinder: Type Single cting, Spring Return/Extend Series Rod Flange (F) F ore size Stroke S T Z Spring return Width across flats 2 Width across flats 1 1 Width across flats K ød L Spring extend ød Width across flats 1 1 L K Z 2 Width across flats 2 Width across flats K K Z + Stroke + Stroke FT 2 Plug with fixed orifice Width across flats N G FT S + Stroke ZZ + Stroke RcP Effective thread length 2 x FL Width across flats N Effective thread length 2 x FL S + Stroke ZZ + 2 x Stroke P Plug with fixed orifice G F 2 x NN øi øe F 2 x NN øe øi ø40 4 x øfd Mounting hole ø40 4 x øfd Mounting hole FY 2 x øfd Mounting hole FY FX FZ ø20 to ø32 C2 2 x øfd Mounting hole FX FZ ø20 to ø32 C2 Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod W K KW oss-cut Spring return ZZ + Stroke Spring extend ZZ + 2 x Stroke ore size L 1 2 C2 D E F FD FL FT FX FY FZ G 1 2 I K K N NN P Z M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/4 45 Dimensions by Stroke Stroke 1 to to to to to 250 ore size S ZZ S ZZ S ZZ S ZZ S ZZ The bracket is shipped together. Refer to page 34 for female thread dimensions. oss-cut Stroke 1 to to to to to 250 ZZ ZZ ZZ ZZ ZZ ore size Direct Mount Direct Mount, Non-rotating Rod R RK uto Switch 36

42 Series ead Flange (G) G ore size Stroke S T Z Spring return C2 2 x øfd Mounting hole Width across flats 1 Width across flats K 1 2 x NN Effective thread length 2 x FL Plug with fixed orifice Width across flats 2 P G 2 FY ød øe øi FX FZ ø20 to ø32 ø40 4 x øfd Mounting hole L K F Width across flats N S + Stroke Z + Stroke FT ZZ + Stroke Spring extend 2 x øfd Mounting hole C2 4 x øfd Mounting hole Width across flats 1 Width across flats K 1 2 x NN Width across flats 2 Effective thread length 2 x FL G P Plug with fixed orifice 2 FY ød øe ø I FX FZ ø20 to ø32 ø40 L K + Stroke F Width across flats N S + Stroke Z + 2 x Stroke ZZ + 2 x Stroke FT ore size L 1 2 C2 D E F FD FL FT FX FY FZ G 1 2 I K K N NN P M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/4 Dimensions by Stroke Stroke 1 to to to to to 250 ore size S Z ZZ S Z ZZ S Z ZZ S Z ZZ S Z ZZ The bracket is shipped together. Refer to page 34 for female thread dimensions. 37

43 ir Cylinder: Type Single cting, Spring Return/Extend Series Single Clevis (C) C ore size Stroke S T Z Spring return Width across flats 1 1 NN Effective thread length FL Plug with fixed orifice P G øcd Spring extend øi CX N N Width across flats K ød øe L K F S + Stroke Z Stroke ZZ Stroke L U RR øci Double cting, Double Rod Single cting, Spring Return/Extend W Width across flats 1 CX N øi N øe ød 1 L Width across flats K Effective thread length FL NN G P Plug with fixed orifice K F + Stroke S + Stroke x Stroke x Stroke Z +1.2 ZZ +1.2 L U RR øcd øci Non-rotating Rod Double cting, Double Rod K KW R Direct Mount ore size L 1 CD CI CX D E F FL G 1 I K K L N NN P RR U M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ Dimensions by Stroke Stroke 1 to to to to to 250 ore size S Z ZZ S Z ZZ S Z ZZ S Z ZZ S Z ZZ Refer to page 34 for female thread dimensions. Direct Mount, Non-rotating Rod RK uto Switch 38

44 Series Double Clevis (D) D ore size Stroke S T Z Spring return øi Width across flats K Width across flats 1 1 NN Effective thread length FL Plug with fixed orifice P G øcd hole xis d N N øe ød øci CX CZ CL N L K F S + Stroke 0 + Stroke 0 + Stroke Z +1.2 ZZ +1.2 L U RR Spring extend øi Width across flats K Width across flats 1 1 Effective thread length FL NN G P Plug with fixed orifice øcd hole xis d øe ød øci CX CZ CL N L K + Stroke F S + Stroke x Stroke x Stroke Z +1.2 ZZ +1.2 L U RR ore size L 1 CD CI CL CX CZ D E F FL G 1 I K K L N NN P RR U M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ Dimensions by Stroke Stroke 1 to to to to to 250 ore size S Z ZZ S Z ZZ S Z ZZ S Z ZZ S Z ZZ Refer to page 34 for female thread dimensions. 39

45 ir Cylinder: Type Single cting, Spring Return/Extend Series Rod Trunnion (U) U ore size Stroke S T Z Spring return Width across flats K Width across flats 1 ød Spring extend 1 L Width across flats 2 K Z TT Plug with fixed orifice Width across flats N S + Stroke ZZ + Stroke P G F 2 x NN øi øe Effective thread length 2 x FL TX TZ øtd øty Double cting, Double Rod Single cting, Spring Return/Extend W Width across flats 1 ød Width across flats K Width across flats 2 1 L K TT Z + Stroke + Stroke G P S + Stroke ZZ + 2 x Stroke Plug with fixed orifice Width across flats N F 2 x NN øi øe Effective thread length 2 x FL TX TZ øtd øty Non-rotating Rod Double cting, Double Rod K KW oss-cut Direct Mount R Spring return ZZ + Stroke Spring extend ZZ + 2 x Stroke ore size L 1 2 D E F FL G 1 I K K N NN P TD TT TX TY TZ Z M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ Dimensions by Stroke Stroke 1 to to to to to 250 ore size S ZZ S ZZ S ZZ S ZZ S ZZ The bracket is shipped together. Refer to page 34 for female thread dimensions. oss-cut ore size Stroke 1 to to to to to 250 ZZ ZZ ZZ ZZ ZZ Direct Mount, Non-rotating Rod RK uto Switch 40

46 Series ead Trunnion (T) T ore size Stroke S T Z Spring return Width across flats 1 2 x NN 1 Effective thread length 2 x FL Plug with fixed orifice Width across flats 2 G P Width across flats K L K F Width across flats x NN Effective thread length 2 x FL G P Plug with fixed orifice øtd øty øe ød øi øty øtd øe ød øi TX TZ Width across flats N S + Stroke Z + Stroke ZZ + Stroke TT Spring extend Width across flats 2 TX TZ Width across flats K L K + Stroke F Width across flats N S + Stroke Z + 2 x Stroke ZZ + 2 x Stroke TT ore size L 1 2 D E F FL G 1 I K K N NN P TD TT TX TY TZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ Dimensions by Stroke Stroke 1 to to to to to 250 ore size S Z ZZ S Z ZZ S Z ZZ S Z ZZ S Z ZZ The bracket is shipped together. Refer to page 34 for female thread dimensions. 41

47 ir Cylinder: Type Single cting, Spring Return/Extend Series Integral Clevis (E) E ore size Stroke Spring return L L N CX LV Spring extend N CX LV øi N øi N S T øe ød Z Width across flats 1 øe ød Width across flats 1 Width across flats K + Stroke K L 1 Width across flats K K F L 1 NN NN F G Plug with fixed orifice Effective thread length FL Effective thread length FL LZ + Stroke ZZ + Stroke Z + Stroke S + Stroke P 2 x øld LT LP L RR U G øcd øci LF LG LY Refer to page 18 for the details of clevis pivot brackets. LZ + 2 x Stroke ZZ + 2 x Stroke Z + 2 x Stroke S + Stroke RcP Plug with fixed orifice 2 x øld LT L U LF RR LP øcd øci LG LY Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod W K KW ore size L 1 CD CI CX D E F FL G 1 I K K L N NN P RR U M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ Dimensions by Stroke Stroke 1 to to to to to 250 ore size S Z ZZ S Z ZZ S Z ZZ S Z ZZ S Z ZZ Clevis Pivot racket ore size LD LF LG L LP LT LV LY 1 to to to to to 250 LZ LZ LZ LZ LZ Direct Mount Direct Mount, Non-rotating Rod R RK uto Switch Refer to page 34 for female thread dimensions. 42

48 ir Cylinder: Non-rotating Rod Type Series K ø20, ø25, ø32, ø40 43 L F G C D U asic (Double-side bossed) xial foot Rod fl ange ead fl ange Single clevis Double clevis Rod trunnion With auto switch With auto switch (uilt-in magnet) Mounting T ead trunnion E Integral clevis V Integral clevis (90 ) Z oss-cut/asic FZ oss-cut/rod fl ange UZ oss-cut/rod trunnion K CDM2K L L ow to Order ore size mm mm mm mm Rod end thread Male rod end F Female rod end uto switch For applicable auto switches, refer to the table below. Cylinder stroke (Refer to Strokes on page 44.) Without auto switch Cushion Rubber bumper ir cushion Z Z Number of auto switches pplicable uto Switches/Refer to the uto Switch Guide for further information on auto switches. Type Special function Solid state auto switch Reed auto switch Electrical entry Indicator light Yes Yes Wiring (Output) Load voltage DC C (Refer to page 44 for details.) M9W 2 pcs. S 1 pc. n n pcs. Lead wire length [m] uto switch model Pre-wired ( ) (M) (L) (Z) None (N) connector Perpendicular In-line M9NV M9N pplicable load 3-wire (NPN) 5 V, 12 V Grommet 3-wire (PNP) M9PV M9P IC circuit M9V M9 2-wire 12 V Connector 7C Terminal 3-wire (NPN) 5 V, 12 V G39 IC circuit conduit 2-wire 12 V K39 Relay, 3-wire (NPN) 24 V M9NWV M9NW Diagnostic indication 5 V, 12 V IC circuit PLC 3-wire (PNP) M9PWV M9PW (2-colour indication) 2-wire 12 V M9WV M9W Water resistant Grommet 3-wire (NPN) M9NV M9N 5 V, 12 V (2-colour 3-wire (PNP) M9PV M9P IC circuit indication) 2-wire 12 V M9V M9 With diagnostic output (2-colour indication) 4-wire (NPN) 5 V, 12 V 7NF IC circuit 3-wire (NPN equivalent) 5 V 96V 96 IC circuit Grommet 100 V 93V V or less 90V 90 IC circuit 100 V, 200 V 54 Relay, 200 V or less 64 PLC Connector 2-wire 24 V 12 V C73C 24 V or less C80C IC circuit Terminal 33 PLC conduit 100 V, 34 Relay, DIN terminal 200 V 44 PLC Diagnostic indication (2-colour indication) Grommet 59W No Yes No Yes No Yes Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please contact SMC regarding water resistant types with the above model numbers. Lead wire length symbols: 0.5 m (Example) M9NW Solid state auto switches marked with are produced upon receipt of order. 1 m M (Example) M9NWM Do not indicate suffi x N for no lead wire on the D-3 /44/G39/K39 3 m L (Example) M9NWL models. 5 m Z (Example) M9NWZ None N (Example) 7CN Since there are other applicable auto switches than listed above, refer to page 69 for details. For details about auto switches with pre-wired connector, refer to the uto Switch Guide. The D-9 /M9 auto switches are shipped together, (but not assembled). (owever, only the auto switch mounting brackets are assembled before shipment.)

49 ir Cylinder: Non-rotating Rod Type Series K cylinder which rod does not rotate because of the hexagonal rod shape. Non-rotating accuracy ø20, ø25 ±0.7 ø32, ø40 ±0.5 Can operate without lubrication. The same installation dimensions as the standard cylinder. uto switches can also be mounted. It can be installed with auto switches to simplify the detection of the stroke position of the cylinder. Rubber bumper ir cushion (For details, refer to pages 71 to 85.) Specifications -X Change of rod end shape -XC3 Special port location -XC6 Made of stainless steel -XC13 uto switch rail mounting -XC20 ead cover axial port -XC25 No fi xed orifi ce of connection port Double clevis and double knuckle pins -XC27 made of stainless steel -XC52 Mounting nut with set screw Refer to pages 65 to 69 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Specifications ore size Rod non-rotating accuracy ±0.7 ±0.5 Type Pneumatic ction Double acting, Single rod Fluid ir Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.05 MPa mbient and fluid temperature Without auto switch: 10 C to 70 C (No freezing) With auto switch: 10 C to 60 C Lubrication Not required (Non-lube) Stroke length tolerance mm Piston speed 50 to 500 mm/s Cushion Rubber bumper, ir cushion Rubber Male thread 0.27 J 0.4 J 0.65 J 1.2 J llowable bumper Female thread 0.11 J 0.18 J 0.29 J 0.52 J kinetic ir cushion 0.54 J 0.78 J 1.27 J 2.35 J energy Male thread (Effective cushion (11.0) (11.0) (11.0) (11.8) length ) Female thread 0.11 J 0.18 J 0.29 J 0.52 J Strokes ore size stroke Note) , 50, 75, 100, 125, 150, 200, 250, Note 1) Intermediate strokes not listed above are produced upon receipt of order. Manufacture of intermediate strokes in 1 mm intervals is possible. (Spacers are not used.) Note 2) The maximum limit is 1000 stroke, but the products that exceed the standard stroke might not be able to fulfi ll the specifi cations. Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch 44

50 Series K Mounting and ccessories ccessories ody Note 1) Rod end nut is not provided for the female rod end type. Note 2) Two mounting nuts are packaged together. Note 3) Mounting nut is not packaged for the clevis. Note 4) Trunnion nut is packaged for U, T, UZ. (mounted to the body) (packaged together, but not assembled) Option Mounting nut Note 1) Rod end nut (Male thread) Single clevis Double clevis Note 7) Liner Mounting nut Foot Flange Pivot bracket Note 5) Pivot bracket pin Note 5) Double clevis pin Note 5) Retaining rings are included. Note 6) pin and retaining rings (split pins for ø40) are included. Note 7) This is the part(s) used to adjust the clevis angle. Mounting quantity can vary. Trunnion Mounting nut (For Trunnion) Clevis pivot bracket (E/V) Clevis pivot Note 5) bracket pin (E/V) Mounting asic (Double-side bossed) (1 pc.) (1 pc.) (1 pc.) L xial foot (1 pc.) (1 pc.) Note 2) (1 pc.) (1 pc.) Note 2) (2 pc.) F Rod fl ange (1 pc.) (1 pc.) (1 pc.) (1 pc.) G ead fl ange (1 pc.) (1 pc.) (1 pc.) (1 pc.) C Single clevis (1 pc.) Note 3) (1 pc.) (1 pc.) (Max. 3 pcs.) Note 3) D Double clevis (1 pc.) Note 3) (1 pc.) (1 pc.) (Max. 3 pcs.) Note 3) (1 pc.) U Rod trunnion (1 pc.) Note 4) (1 pc.) (1 pc.) (1 pc.) T ead trunnion (1 pc.) Note 4) (1 pc.) (1 pc.) (1 pc.) E Integral clevis (1 pc.) Note 3) (1 pc.) Note 3) V Integral clevis (90 ) (1 pc.) Note 3) (1 pc.) Note 3) Z oss-cut/asic (1 pc.) (1 pc.) (1 pc.) FZ oss-cut/ Rod fl ange UZ oss-cut/ Rod trunnion Mounting rackets/part No. (1 pc.) (1 pc.) (1 pc.) (1 pc.) (1 pc.) Note 4) (1 pc.) (1 pc.) (1 pc.) Single knuckle joint (Male thread only) Note 6) Double knuckle joint (Male thread only) Mounting bracket Min. ore size order q ty Contents (for minimum order quantity) Foot 2 CM-L020 CM-L032 CM-L040 2 foots, 1 mounting nut Flange 1 CM-F020 CM-F032 CM-F040 1 fl ange Single clevis 1 CM-C020 CM-C032 CM-C040 1 single clevis, 3 liners Double clevis (with pin) 1 CM-D020 CM-D032 CM-D040 Order 2 foots per cylinder. 3 liners are included with a clevis bracket for adjusting the mounting angle. clevis pin and retaining rings (split pins for ø40) are included. 1 double clevis, 3 liners, 1 clevis pin, 2 retaining rings Trunnion (with nut) 1 CM-T020 CM-T032 CM-T040 1 trunnion, 1 trunnion nut Rod end nut 1 NT-02 NT-03 NT-04 1 rod end nut Mounting nut 1 SN-020 SN-032 SN mounting nut Trunnion nut 1 TN-020 TN-032 TN trunnion nut Single knuckle joint 1 I-020 I-032 I single knuckle joint Double knuckle joint 1 Y-020 Y-032 Y double knuckle joint, 1 clevis pin, 2 retaining rings Clevis pin (Double clevis) 1 CDP-1 CDP-2 1 clevis pin, 2 retaining rings (split pins) Clevis pin (Double knuckle joint) 1 CDP-1 CDP-3 1 clevis pin, 2 retaining rings (split pins) Pivot bracket pin 1 CDP-1 CD-S03 1 pin, 2 retaining rings Clevis pivot bracket pin (For E/V) 1 CD-S02 CD-S03 1 clevis pin, 2 retaining rings Clevis pivot bracket (For E/V) 1 CM-E020 CM-E032 1 clevis pivot bracket, 1 clevis pin, 2 retaining rings Pivot bracket (For C) 1 CM-032 CM pivot brackets (1 of each type) Pivot bracket (For U/T) 1 CM-020 CM-032 CM pivot brackets (1 of each type) 45

51 ir Cylinder: Non-rotating Rod Type Series K Mounting rackets, ccessories/material, Surface Treatment Segment Description Material Surface treatment Mounting brackets ccessories Weights Foot Carbon steel Nickel plating Flange Carbon steel Nickel plating Single clevis Carbon steel Nickel plating Double clevis Carbon steel Nickel plating Trunnion Cast iron Electroless nickel plating Rod end nut Carbon steel Zinc chromated Mounting nut Carbon steel Nickel plating Trunnion nut Carbon steel Nickel plating Pivoting clevis bracket Carbon steel Nickel plating Pivoting clevis bracket pin Carbon steel (None) Single knuckle joint Carbon steel ø40: Free-cutting steel Electroless nickel plating Double knuckle joint Carbon steel ø40: Cast iron Double clevis pin Carbon steel (None) Double knuckle joint pin Carbon steel (None) Pivoting bracket Carbon steel Nickel plating Pivoting bracket pin Carbon steel (None) Electroless nickel plating Metallic bronze colour painted for ø40 [kg] ore size asic xial foot Flange Integral clevis asic Single clevis weight Double clevis Trunnion oss-cut/asic oss-cut/flange oss-cut/trunnion dditional weight per 50 mm of stroke Clevis bracket (with pin) Option Single knuckle joint bracket Double knuckle joint (with pin) Calculation: (Example) KL32-100Z asic weight 0.44 (Foot, ø32) dditional weight 0.09/0.50 stroke Cylinder stroke 100 stroke x 100/50 = 0.62 kg Precautions e sure to read before handling. Refer to back cover for Safety Instructions. For ctuator and uto Switch Precautions, refer to andling Precaution for SMC Products and the Operation Manual on SMC website, Operating Precautions Warning 1. Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fi tting into the port, it is likely to damage the junction part with cover. 2. Do not operate with the cushion needle in a fully closed condition. Using it in the fully closed state will cause the cushion seal to be damaged. When adjusting the cushion needle, use the exagon wrench key: nominal size Do not open the cushion needle wide excessively. If the cushion needle were set to be completely wide (more than 3 turns from fully closed), it would be equivalent to the cylinder with no cushion, thus making the impacts extremely high. Do not use it in such a way. esides, using with fully open could give damage to the piston or cover. Caution 1. void using the air cylinder in such a way that rotational torque would be applied to the piston rod. If rotational torque is applied, the non-rotating guide will become deformed, thus affecting the nonrotating accuracy. Refer to the table below for the approximate values of the allowable range of rotational torque. llowable rotational torque (N m or less) ø20 ø25 ø32 ø To screw a bracket or a nut onto the threaded portion at the tip of the piston rod, make sure to retract the piston rod entirely, and place a wrench over the flat portion of the rod that protrudes. Tighten it by giving consideration to prevent the tightening torque from being applied to the nonrotating guide. 2. When replacing rod seals, please contact SMC. ir leakage may be happened, depending on the position in which a rod seal is fi tted. Thus, please contact SMC when replacing them. 3. Not able to disassemble. Cover and cylinder tube are connected to each other by caulking method, thus making it impossible to disassemble. Therefore, internal parts of a cylinder other than rod seal are not replaceable. 4. Do not touch the cylinder during operation. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 5. The oil stuck to the cylinder is grease. 6. The base oil of grease may seep out. Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch 46

52 Series K Construction Rubber bumper oss-cut Clevis integrated Rod section With air cushion!8 Rod section Component Parts No. Description Material Note 1 Rod cover luminium alloy nodised 2 ead cover luminium alloy nodised 2 ead cover luminium alloy nodised 2C ead cover C luminium alloy nodised 3 Cylinder tube Stainless steel 4 Piston luminium alloy 5 Piston rod Stainless steel 6 Non-rotating guide earing alloy 7 Seal retainer Carbon steel Nickel plating 8 Retaining ring Carbon steel Phosphate coating 9 Clevis bushing Copper oil-impregnated sintered alloy 10 umper Resin 11 umper Resin No. Description Material Note 12 Retaining ring Stainless steel 13 Piston seal NR 14 Piston gasket NR 15 Wear ring Resin 16 Mounting nut Carbon steel Nickel plating 17 Rod end nut Carbon steel Zinc chromated Replacement Part/Seal With Rubber umper/with ir Cushion Part no. No. Description Material Rod seal NR K20-PS K25-PS K32-PS K40-PS Since the seal kit does not include a grease pack, order it separately. Grease pack part number: GR-S-010 (10 g) 47

53 ir Cylinder: Non-rotating Rod Type Series K asic (Double-side ossed) () K ore size Stroke With rod boot J JW Cushion needle (Width across flats 1.5) 45 øe With air cushion Stroke N øi N Width across flats 1 Width across flats K 8 8 l W Z Width across flats 2 2 G f h ZZ + Stroke 1 L F Width across flats 3 2 x RcP S + Stroke ZZ + Stroke oss-cut W G F ZZ + Stroke Cushion needle (Width across flats 1.5) 45 2 x NN 2 x øeh8 Female thread Thread depth 1 Effective thread length 2 x FL Female rod end The dimensions are the same as standard type, double acting, single rod, except the configuration of the piston rod. Refer to pages 9 to 16. Specifi cations for the auto switch equipped type are the same as the CDM2 series standard type. ZZ + Stroke ore size L 1 2 E F FL G 1 2 I K N NN P S ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ With Rod oot h l ZZ 3 e f ore size 1 to to to to to to to to to to to to to to to 300 J JW oss-cut With ir Cushion Female Rod End ZZ ore size W ore size 1 ZZ ore size Without With rod boot M4 x rod boot 1 to to to to to M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at Dimensions of Each Mounting racket the rod end from being deformed depending on the material of the workpiece. 48 Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch

54 ir Cylinder: Non-rotating Rod Type Double cting, Double Rod Series KW ø20, ø25, ø32, ø40 ow to Order Mounting asic (Double-side bossed) L xial foot F Flange U Trunnion KW L Cylinder stroke (Refer to Strokes on page 50.) Cushion Rubber bumper ir cushion Z (Refer to page 50 for details.) With auto switch CDM2KW L Z M9W With auto switch (uilt-in magnet) Non-rotating rod type ore size mm mm mm mm Rod end thread Male rod end F Female rod end uto switch Without auto switch For applicable auto switches, refer to the table below. Number of auto switches 2 pcs. S 1 pc. n n pcs. pplicable uto Switches/Refer to the uto Switch Guide for further information on auto switches. Type Special function Solid state auto switch Reed auto switch Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please contact SMC regarding water resistant types with the above model numbers. Lead wire length symbols: 0.5 m (Example) M9NW Solid state auto switches marked with are produced upon receipt of order. 1 m M (Example) M9NWM Do not indicate suffi x N for no lead wire on the D-3 /44/G39/K39 3 m L (Example) M9NWL models. 5 m Z (Example) M9NWZ None N (Example) 7CN Since there are other applicable auto switches than listed above, refer to page 69 for details. For details about auto switches with pre-wired connector, refer to the uto Switch Guide. The D-9 /M9 auto switches are shipped together, (but not assembled). (owever, only the auto switch mounting brackets are assembled before shipment.) 49 Electrical entry Indicator light Yes Yes Wiring (Output) Load voltage DC C Lead wire length [m] uto switch model Pre-wired ( ) (M) (L) (Z) None (N) connector Perpendicular In-line M9NV M9N pplicable load 3-wire (NPN) 5 V, 12 V Grommet 3-wire (PNP) M9PV M9P IC circuit M9V M9 2-wire 12 V Connector 7C Terminal 3-wire (NPN) 5 V, 12 V G39 IC circuit conduit 2-wire 12 V K39 Relay, 3-wire (NPN) 24 V M9NWV M9NW Diagnostic indication 5 V, 12 V IC circuit PLC 3-wire (PNP) M9PWV M9PW (2-colour indication) 2-wire 12 V M9WV M9W Water resistant Grommet 3-wire (NPN) M9NV M9N 5 V, 12 V (2-colour 3-wire (PNP) M9PV M9P IC circuit indication) 2-wire 12 V M9V M9 With diagnostic output (2-colour indication) 4-wire (NPN) 5 V, 12 V 7NF IC circuit 3-wire (NPN equivalent) 5 V 96V 96 IC circuit Grommet 100 V 93V V or less 90V 90 IC circuit 100 V, 200 V 54 Relay, 200 V or less 64 PLC Connector 2-wire 24 V 12 V C73C 24 V or less C80C IC circuit Terminal 33 PLC conduit 100 V, 34 Relay, DIN terminal 200 V 44 PLC Diagnostic indication (2-colour indication) Grommet 59W No Yes No Yes No Yes

55 ir Cylinder: Non-rotating Rod Type Double cting, Double Rod Series KW cylinder which rod does not rotate because of the hexagonal rod shape. Non-rotating accuracy ø20, ø25 ±0.7 ø32, ø40 ±0.5 Can operate without lubrication. The same installation dimensions as the standard cylinder. uto switches can also be mounted. It can be installed with auto switches to simplify the detection of the stroke position of the cylinder. Rubber bumper ir cushion (For details, refer to pages 71 to 85.) Specifications -X Change of rod end shape -X6 eat resistant cylinder ( 10 to 150 C) -XC3 Special port location -XC13 uto switch rail mounting -XC22 Fluororubber seal -XC52 Mounting nut with set screw Specifications ore size Rod non-rotating accuracy ±0.7 ±0.5 ction Pneumatic Cushion Rubber bumper, ir cushion ction Double acting, Double rod Fluid ir Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.08 MPa mbient and fluid temperature ore size stroke Note) 25, 50, 75, 100, 125, 150, 200, 250, 300 Note 1) Intermediate strokes not listed above are produced upon receipt of order. Manufacture of intermediate strokes in 1 mm intervals is possible. (Spacers are not used.) Note 2) The maximum limit is 500 stroke, but the products that exceed the standard stroke might not be able to fulfill the specifications. Refer to pages 17 and 18 for accessory bracket, since it is the same as standard type, double acting, single rod. Mounting ccessory equipment Mounting nut Without auto switch: 10 C to 70 C (No freezing) With auto switch: 10 C to 60 C Lubrication Not required (Non-lube) Stroke length tolerance mm Piston speed 50 to 500 mm/s Rubber Male thread 0.27 J 0.4 J 0.65 J 1.2 J llowable bumper Female thread 0.11 J 0.18 J 0.29 J 0.52 J kinetic ir cushion 0.54 J 0.78 J 1.27 J 2.35 J energy Male thread (Effective cushion (11.0) (11.0) (11.0) (11.8) length ) Female thread 0.11 J 0.18 J 0.29 J 0.52 J Strokes ccessory racket Mounting and ccessories Rod end nut Single knuckle joint Option Note 2) Double knuckle joint Pivot bracket Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK asic (1 pc.) (2 pcs.) xial foot (2) (2) Flange (1) (2) Trunnion (1) Note1) (2) Note 1) Trunnion nuts are attached to the trunnion. Note 2) pin and retaining rings (split pins for ø40) are shipped together with double knuckle joint. Refer to pages 65 to 69 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. uto Switch 50

56 Series KW Weights KW Mounting style [kg] ore size asic (Double-side bossed) asic xial foot weight Flange Trunnion dditional weight per 50 mm of stroke Option bracket Single knuckle joint Double knuckle joint (With pin) Calculation: (Example) KWL32-100Z asic weight 0.48 (Foot, ø32) dditional weight 0.14/50 stroke Cylinder stroke: 100 stroke x 100/50 = 0.76 kg Mounting rackets/part No. Mounting bracket Min. ore size order q ty Description (for min. order) xial foot 2 CM-L020 CM-L032 CM-L040 2 foots, 1 mounting nut Flange 1 CM-F020 CM-F032 CM-F040 1 fl ange Trunnion (with nuts) 1 CM-T020 CM-T032 CM-T040 1 trunnion, 1 trunnion nut Order 2 foots per cylinder unit. With ir Cushion ore size Stroke Z With air cushion The cushion mechanism is provided for covers in both sides to absorb the impacts when operating at a high speed, thus giving no vibrations to a surrounding area and a long service life brought to cylinder. Refer to page 21 for the specifications and allowable kinetic energy since this cylinder has the same specification as the double acting double rod model. Precautions e sure to read before handling. Refer to back cover for Safety Instructions. For ctuator and uto Switch Precautions, refer to andling Precaution for SMC Products and the Operation Manual on SMC website, Operating Precautions Warning 1. Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fi tting into the port, it is likely to damage the junction part with cover. 2. Do not operate with the cushion needle in a fully closed condition. Using it in the fully closed state will cause the cushion seal to be damaged. When adjusting the cushion needle, use the exagon wrench key: nominal size Do not open the cushion needle wide excessively. If the cushion needle were set to be completely wide (more than 3 turns from fully closed), it would be equivalent to the cylinder with no cushion, thus making the impacts extremely high. Do not use it in such a way. esides, using with fully open could give damage to the piston or cover. Caution 1. void using the air cylinder in such a way that rotational torque would be applied to the piston rod. If rotational torque is applied, the nonrotating guide will become deformed, thus affecting the non-rotating accuracy. Refer to the table below for the approximate values of the allowable range of rotational torque. llowable rotational torque (N m or less) ø20 ø25 ø32 ø To screw a bracket or a nut onto the threaded portion at the tip of the piston rod, make sure to retract the piston rod entirely, and place a wrench over the flat portion of the rod that protrudes. Tighten it by giving consideration to prevent the tightening torque from being applied to the non-rotating guide. 2. When replacing rod seals, please contact SMC. ir leakage may be happened, depending on the position in which a rod seal is fitted. Thus, please contact SMC when replacing them. 3. Not able to disassemble. Cover and cylinder tube are connected to each other by caulking method, thus making it impossible to disassemble. Therefore, internal parts of a cylinder other than rod seal are not replaceable. 4. Do not touch the cylinder during operation. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 5. The oil stuck to the cylinder is grease. 6. The base oil of grease may seep out. 51

57 ir Cylinder: Non-rotating Rod Type Double cting, Double Rod Series KW Construction Rubber bumper Double cting, Double Rod W With air cushion Rod section Rod section!7!8 Rod section Rod section Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod K KW Component Parts No. Description Material Note 1 Rod cover luminium alloy nodised 2 Cylinder tube Stainless steel 3 Piston luminium alloy 4 Piston rod Carbon steel ard chrome plating 5 Piston rod Stainless steel 6 ushing earing alloy 7 Non-rotating guide earing alloy 8 Seal retainer Stainless steel 9 Seal retainer Carbon steel Nickel plating 10 Retaining ring Carbon steel Phosphate coating 11 umper Resin 12 umper Resin 13 Piston seal NR 14 Piston gasket NR 15 Mounting nut Carbon steel Zinc chromated 16 Rod end nut Carbon steel Nickel plating Replacement Parts/Seal With Rubber umper/with ir Cushion No. Description Material ore size Rod seal NR 0Z-PS 5Z-PS CM32Z-PS CM40Z-PS 18 Rod seal NR K20-PS K25-PS K32-PS K40-PS Since the seal kit does not include a grease pack, order it separately. Grease pack part number: GR-S-010 (10 g) Direct Mount Direct Mount, Non-rotating Rod R RK uto Switch 52

58 Series KW asic (Double-side ossed) () WK ore size Stroke Z øi Width across flats 2 2 G Width across flats x RcP G 2 x NN Width across flats K N N ød Width across flats K L K F S + Stroke ZZ + 2 x Stroke F 2 x øeh8 Effective thread length 2 x FL + Stroke L With air cushion 45 W W Cushion needle (Width across flats 1.5) Female rod end Female thread Thread depth ZZ + 2 x Stroke ore size L 1 2 D E F FL G 1 2 I K K K N NN P S ZZ M8 x M20 x 1.5 1/ M10 x M26 x 1.5 1/ M10 x M26 x 1.5 1/ M14 x M32 x 2 1/ With ir Cushion ore size W Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. Dimensions of Each Mounting racket External dimensions of each mounting bracket other than basic type are the same as standard type, double acting, double rod (except K dimensions). Refer to pages 26 to

59 With auto switch ir Cylinder: Direct Mount Type Series R ø20, ø25, ø32, ø40 Pneumatic ir-hydro CDM2 ow to Order Cylinder stroke (Refer to Strokes on page 55.) Type R R Cushion Rubber bumper ir cushion ir-hydro cylinder: Rubber bumper only Z Z (Refer to page 55 for details.) M9W Double cting, Double Rod Single cting, Spring Return/Extend W With auto switch (uilt-in magnet) Mounting style ottom mounting style Front mounting style ore size mm mm mm mm Rod end thread Male rod end F Female rod end pplicable uto Switches/Refer to the uto Switch Guide for further information on auto switches. Type Special function Solid state auto switch Reed auto switch Electrical entry Indicator light Yes Yes Wiring (Output) Load voltage DC C Number of auto switches 2 pcs. S 1 pc. n n pcs. uto switch Without auto switch For applicable auto switches, refer to the table below. Lead wire length [m] uto switch model Pre-wired ( ) (M) (L) (Z) None (N) connector Perpendicular In-line M9NV M9N pplicable load 3-wire (NPN) 5 V, 12 V Grommet 3-wire (PNP) M9PV M9P IC circuit M9V M9 2-wire 12 V Connector 7C Terminal 3-wire (NPN) 5 V, 12 V G39 IC circuit conduit 2-wire 12 V K39 Relay, 3-wire (NPN) 24 V M9NWV M9NW Diagnostic indication 5 V, 12 V IC circuit PLC 3-wire (PNP) M9PWV M9PW (2-colour indication) 2-wire 12 V M9WV M9W Water resistant Grommet 3-wire (NPN) M9NV M9N 5 V, 12 V (2-colour 3-wire (PNP) M9PV M9P IC circuit indication) 2-wire 12 V M9V M9 With diagnostic output (2-colour indication) 4-wire (NPN) 5 V, 12 V 7NF IC circuit 3-wire (NPN equivalent) 5 V 96V 96 IC circuit Grommet 100 V 93V V or less 90V 90 IC circuit 100 V, 200 V 54 Relay, 200 V or less 64 PLC Connector 2-wire 24 V 12 V C73C 24 V or less C80C IC circuit Terminal 33 PLC conduit 100 V, 34 Relay, DIN terminal 200 V 44 PLC Diagnostic indication (2-colour indication) Grommet 59W No Yes No Yes No Yes Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please contact SMC regarding water resistant types with the above model numbers. Lead wire length symbols: 0.5 m (Example) M9NW Solid state auto switches marked with are produced upon receipt of order. 1 m M (Example) M9NWM Do not indicate suffi x N for no lead wire on the D-3 /44/G39/K39 3 m L (Example) M9NWL models. 5 m Z (Example) M9NWZ None N (Example) 7CN Since there are other applicable auto switches than listed above, refer to page 69 for details. For details about auto switches with pre-wired connector, refer to the uto Switch Guide. The D-9 /M9 auto switches are shipped together, (but not assembled). (owever, only the auto switch mounting brackets are assembled before shipment.) 54 Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod K KW R RK uto Switch

60 Series R The R direct mount cylinder can be installed directly through the use of a square rod cover. Space saving has been realised. ecause it is a directly mounted style without using brackets, its overall length is shorter, and its installation pitch can be made smaller. Thus, the space that is required for installation is dramatically reduced. Improved installation accuracy and strength centreing boss is provided to improve the installation accuracy. lso, because it is the directly mounted style, the strength is increased. Two styles of installation Two styles of installations are available and can be selected according to the purpose: the front mounting style or the bottom mounting style. Specifications ore size ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Double acting, Single rod ir 1.5 MPa 1.0 MPa 0.05 MPa Without auto switch: 10 C to 70 C (No freezing) With auto switch: 10 C to 60 C Lubrication Not required (Non-lube) +1.4 Stroke length tolerance 0 mm Piston speed Rubber bumper: 50 to 750 mm/s, ir cushion: 50 to 1000 mm/s Cushion Rubber bumper, ir cushion Rubber Male thread 0.27 J 0.4 J 0.65 J 1.2 J llowable bumper Female thread 0.11 J 0.18 J 0.29 J 0.52 J kinetic ir cushion 0.54 J 0.78 J 1.27 J 2.35 J energy Male thread (Effective cushion (11.0) (11.0) (11.0) (11.8) length ) Female thread 0.11 J 0.18 J 0.29 J 0.52 J Strokes ottom mounting style Front mounting style ore size stroke (1) Max. manufacturable stroke (2) 20 25, 50, 75, 100, 125, , 50, 75, 100, 125, 150, , 50, 75, 100, 125, 150, , 50, 75, 100, 125, 150, 200, 250, Note 1) Other intermediate strokes can be manufactured upon receipt of order. Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) Refer to the next page for Precautions. ir cushion Tightening Torque: Tighten the cylinder mounting bolts for the bottom mounting style (Series R) with the following tightening torque. ore size exagon socket head cap screw size Tightening torque [N m] 20 M5 x to M6 4.2 to M to M to 29.4 (For details, refer to pages 71 to 85.) Specifi cations -X Change of rod end shape -X6 eat resistant cylinder ( 10 to 150 C) -X7 Cold resistant cylinder ( 40 to 70 C) -X9 Low speed cylinder (10 to 50 mm/s) -XC3 Special port location -XC6 Made of stainless steel -XC20 ead cover axial port -XC22 Fluororubber seal -XC29 Double knuckle joint with spring pin -XC85 Grease for food processing equipment -X446 PTFE grease Refer to pages 65 to 69 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. 55

61 ir Cylinder: Direct Mount Type Series R ccessories Mounting ccessory equipment Option Rod end nut Single knuckle joint Double knuckle joint (With pin) ottom mounting style Front mounting style knuckle pin and retaining rings (split pin for ø40) are shipped together. Weights (kg) ore size ottom mounting style asic weight Front mounting style dditional weight per 50 mm of stroke Calculation: (Example) R32-100Z (ø32, 100 stroke, ottom mounting) asic weight 0.32 kg dditional weight 0.08 kg Cylinder stroke 100 stroke x 100/50 = 0.48 kg e sure to read before handling. Refer to back cover for Safety Instructions. For ctuator and uto Switch Precautions, refer to andling Precaution for SMC Products and the Operation Manual on SMC website, Warning 1. Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fi tting into the port, it is likely to damage the junction part with cover. 2. Do not operate with the cushion needle in a fully closed condition. Using it in the fully closed state will cause the cushion seal to be damaged. When adjusting the cushion needle, use the exagon wrench key: nominal size Do not open the cushion needle wide excessively. If the cushion needle were set to be completely wide (more than 3 turns from fully closed), it would be equivalent to the cylinder with no cushion, thus making the impacts extremely high. Do not use it in such a way. esides, using with fully open could give damage to the piston or cover. 4. In the case of exceeding the standard stroke length, implement an intermediate support. When using cylinder with longer stroke, implement an intermediate support for preventing the joint of rod cover and cylinder tube from being broken by vibration or external load. 5. Operate the cylinder within the specified cylinder speed, kinetic energy and lateral load at the rod end. 6. The allowable kinetic energy is different between the cylinders with male rod end and with female rod end due to the different thread sizes. 7. When female rod end is used, use a washer, etc. to prevent the contact part at the rod end from being deformed depending on the material of the work piece. 8. Do not apply excessive lateral load to the piston rod. Easy checking method Minimum operating pressure after the cylinder is mounted to the equipment [MPa] = Minimum operating pressure of cylinder [MPa] + {Load weight [kg] x Friction coeffi cient of guide/sectional area of cylinder [mm 2 ]} If smooth operation is confi rmed within the above value, the load on the cylinder is the resistance of the thrust only and it can be judged as having no lateral load. Precautions Operating Precautions Caution 1. Not able to disassemble. Cover and cylinder tube are connected to each other by caulking method, thus making it impossible to disassemble. Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (retaining ring plier: tool for installing a type C retaining ring). Even if a proper tool is used, it is likely to infl ict damage to a human body or peripheral equipment, as a retaining ring may be fl own out of the tip of a plier. e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed fi rmly into the groove of rod cover before supplying air at the time of installment. 3. Do not touch the cylinder during operation. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 4. Do not use an air cylinder as an air-hydro cylinder. If it uses turbine oil in place of fl uids for cylinder, it may result in oil leakage. 5. The oil stuck to the cylinder is grease. 6. The base oil of grease may seep out. 56 Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch

62 Series R Clean Series ir-hydro 10-R Mounting style ore size Stroke Z R Mounting style ore size Stroke Z Clean Series (With relief port) The type which is applicable for using inside the clean room graded Class 100 by making an actuator s rod section a double seal construction and discharging by relief port directly to the outside of clean room. ir-hydro low hydraulic pressure cylinder used at a pressures of 1.0 MPa or below. Through the concurrent use of the CC series air-hydro unit, it is possible to operate at a constant or low speeds or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve. Specifications ction Double acting, Single rod ore size ø20, ø25, ø32, ø40 Max. operating pressure 1.0 MPa Min. operating pressure 0.05 MPa Cushion Rubber bumper ( equipment) Relief port size M5 x 0.8 Piston speed 30 to 400 mm/s Mounting ottom mounting style, Front mounting style uto switch can be mounted. Construction Specifications Type ir-hydro Fluid Turbine oil ction Double acting, Single rod ore size ø20, ø25, ø32, ø40 Proof pressure 1.5 MPa Max. operating pressure 1.0 MPa Min. operating pressure 0.18 MPa Piston speed 15 to 300 mm/s Cushion Rubber bumper mbient and fluid temperature +5 to +60 C Thread tolerance mm Stroke length tolerance Mounting ottom mounting style, Front mounting style uto switches can be mounted. Dimensions are the same as the R series standard type. For construction, refer to page 58. Since the dimensions of mounting style is the same as pages 59 and 60, refer to those pages. Front mounting style ottom mounting style M5 x 0.8 Relief port GC M5 x 0.8 Relief port GC ore size GC

63 ir Cylinder: Direct Mount Type Series R Construction Rubber bumper t i u!5 y q o e r!1!4!2!0 w Double cting, Double Rod W ir-hydro!3!5 Single cting, Spring Return/Extend With air cushion!5 Non-rotating Rod Double cting, Double Rod K KW Component Parts No. Description Material Note 1 Rod cover luminium alloy nodised 2 ead cover luminium alloy nodised 3 Cylinder tube Stainless steel 4 Piston luminium alloy 5 Piston rod Carbon steel ard chrome plating 6 ushing earing alloy 7 Seal retainer Stainless steel 8 Retaining ring Carbon steel Phosphate coating 9 umper Resin ø25 or larger is 10 umper Resin common. 11 Piston seal NR 12 Wear ring Resin 13 Rod end nut Carbon steel Zinc chromated 14 Magnet CDM2R 20 to 40- Z For auto switch proper mounting position (at stroke end), refer to pages 66 and 68, since the operating range is the same as standard type, single rod. Replacement Part/Seal With Rubber umper/with ir Cushion Part no. No. Description Material Rod seal NR 0Z-PS 5Z-PS CM32Z-PS CM40Z-PS ir-hydro No. Description Material Part no Rod seal NR 20-PS 25-PS 32-PS 40-PS Since the seal kit does not include a grease pack, order it separately. Grease pack part number: GR-S-010 (10 g) 58 Direct Mount Direct Mount, Non-rotating Rod R RK uto Switch

64 Series R ottom Mounting Style R ore size Stroke Z Width across flats 1 øi 1 X G Y 2 x RcP G 2 x øld N N ønd ød Width across flats K L K S + Stroke ZZ + Stroke LX L L With air cushion Cushion needle (Width across flats 1.5) 45 W W Cushion needle (Width across flats 1.5) 13 W Female rod end Width across flats K Female thread Thread depth ZZ + Stroke ore size Stroke range L 1 D GG 1 I K K L LD L LX N ND P S X Y ZZ 20 1 to ø5.5, ø9.5 counterbore depth M8 x / to ø6.6, ø11 counterbore depth M10 x / to ø9, ø14 counterbore depth M10 x / to ø11, ø17.5 counterbore depth M14 x / With ir Cushion ore size W W W Female Rod End ore size 1 K ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece.

65 ir Cylinder: Direct Mount Type Series R Front Mounting Style R ore size Stroke Z øi Width across flats 1 1 G 2 x RcP G 4 x FF N With air cushion 45 N Cushion needle (Width across flats 1.5) ød ønd Width across flats K Width across flats K Female thread L W K Female rod end S + Stroke ZZ + Stroke W F FX 13 W FX F Cushion needle (Width across flats 1.5) Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod W K KW Thread depth ZZ + Stroke Direct Mount R ore size Stroke range L 1 D F FF FX G G 1 I K K N ND P S ZZ 20 1 to M5 x 0.8 depth M8 x / to M6 x 1 depth M10 x / to M6 x 1 depth M10 x / to M8 x 1.25 depth M14 x / Direct Mount, Non-rotating Rod RK With ir Cushion ore size W W W Female Rod End ore size 1 K ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the material of the workpiece. uto Switch 60

66 ir Cylinder: Direct Mount, Non-rotating Rod Type Series RK ø20, ø25, ø32, ø40 ow to Order Cylinder stroke (Refer to Strokes on page 62.) RK Z (Refer to page 62 for details.) With auto switch CDM2RK Z M9W With auto switch (uilt-in magnet) Mounting ottom mounting style Front mounting style ore size mm mm mm mm Rod end thread Male rod end F Female rod end uto switch Without auto switch For applicable auto switches, refer to the table below. Number of auto switches 2 pcs. S 1 pc. n n pcs. pplicable uto Switches/Refer to the uto Switch Guide for further information on auto switches. Type Special function Solid state auto switch Reed auto switch Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Please contact SMC regarding water resistant types with the above model numbers. Lead wire length symbols: 0.5 m (Example) M9NW Solid state auto switches marked with are produced upon receipt of order. 1 m M (Example) M9NWM Do not indicate suffix N for no lead wire on D-3 /44/G39/K39 models. 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) 7CN Since there are other applicable auto switches than listed above, refer to page 69 for details. For details about auto switches with pre-wired connector, refer to the uto Switch guide. The D-9 /M9 auto switches are shipped together, (but not assembled). (owever, only the auto switch mounting brackets are assembled before shipment.) 61 Electrical entry Indicator light Yes Yes Wiring (Output) Load voltage DC C Lead wire length [m] uto switch model Pre-wired ( ) (M) (L) (Z) None (N) connector Perpendicular In-line M9NV M9N pplicable load 3-wire (NPN) 5 V, 12 V Grommet 3-wire (PNP) M9PV M9P IC circuit M9V M9 2-wire 12 V Connector 7C Terminal 3-wire (NPN) 5 V, 12 V G39 IC circuit conduit 2-wire 12 V K39 Relay, 3-wire (NPN) 24 V M9NWV M9NW Diagnostic indication 5 V, 12 V IC circuit PLC 3-wire (PNP) M9PWV M9PW (2-colour indication) 2-wire 12 V M9WV M9W Water resistant Grommet 3-wire (NPN) M9NV M9N 5 V, 12 V (2-colour 3-wire (PNP) M9PV M9P IC circuit indication) 2-wire 12 V M9V M9 With diagnostic output (2-colour indication) 4-wire (NPN) 5 V, 12 V 7NF IC circuit 3-wire (NPN equivalent) 5 V 96V 96 IC circuit Grommet 100 V 93V V or less 90V 90 IC circuit 100 V, 200 V 54 Relay, 200 V or less 64 PLC Connector 2-wire 24 V 12 V C73C 24 V or less C80C IC circuit Terminal 33 PLC conduit 100 V, 34 Relay, DIN terminal 200 V 44 PLC Diagnostic indication (2-colour indication) Grommet 59W No Yes No Yes No Yes

67 ir Cylinder: Direct Mount, Non-rotating Rod Type Series RK The R direct mount cylinder can be installed directly through the use of a square rod cover. Non-rotating accuracy type of cylinder in which the rod does not rotate because of its hexagonal shape Cylinder ø20, ø25 ±0.7 ø32, ø40 ±0.5 Space-saving configuration ecause it is a directly mounted style without using brackets, its overall length is shorter, and its installation pitch can be made smaller. Thus, the space that is required for installation is dramatically reduced. Improved installation accuracy and strength centreing boss is provided to improve the installation accuracy. lso, because it is the directly mounted style, the strength is increased. Two styles of installation Two styles of installations are available and can be selected according to the purpose: the front mounting style or the bottom mounting style. Specifications ore size Rod non-rotating accuracy ± 0.7 ± 0.5 ction Double acting, Single rod Fluid ir Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.05 MPa mbient and fluid temperature Without auto switch: 10 C to 70 C (No freezing) With auto switch: 10 C to 60 C Lubrication Not required (Non-lube) +1.4 Stroke length tolerance 0 mm Piston speed 50 to 500 mm/s Cushion Rubber bumper llowable kinetic (Male thread) 0.27 J 0.4 J 0.65 J 1.2 J energy (Female thread) 0.11 J 0.18 J 0.29 J 0.52 J Strokes ore size stroke Note 1) 20 25, 50, 75, 100, 125, , 50, 75, 100, 125, 150, , 50, 75, 100, 125, 150, , 50, 75, 100, 125, 150, 200, 250, 300 Note 1) Other intermediate strokes can be manufactured upon receipt of order. Manufacture of intermediate strokes at 1 mm intervals is possible. (Spacers are not used.) Note 2) The maximum limit is 1000 stroke, but the products that exceed the standard stroke might not be able to fulfi ll the specifi cations. Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod W K KW ottom mounting style Rubber bumper Front mounting style Tightening Torque: Tighten the cylinder mounting bolts for the bottom mounting style (Series R) with the following tightening torque. ore size exagon socket head cap bolt size Tightening torque [N m] 20 M5 x to M6 4.2 to M to M to 29.4 Direct Mount Direct Mount, Non-rotating Rod R RK -X -XC3 -XC6 -XC20 (For details, refer to pages 71 to 85.) Specifications Change of rod end shape Special port location Made of stainless steel ead cover axial port Refer to pages 65 to 69 for cylinders with an auto switch. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. uto Switch 62

68 Series RK Construction Rod section Component Parts No. Description Material Note 1 Rod cover luminium alloy nodised 2 ead cover luminium alloy nodised 3 Cylinder tube Stainless steel 4 Piston luminium alloy 5 Piston rod Stainless steel 6 Non-rotating guide earing alloy 7 Seal retainer Carbon steel Nickel plating 8 Retaining ring Carbon steel Phosphate coating 9 umper Resin 10 umper Resin 11 Retaining ring Stainless steel No. Description Material Note 12 Piston seal NR 13 Piston gasket NR 14 Wear ring Resin 15 Rod end nut Carbon steel Zinc chromated Replacement Part/Seal No. Description Material Part no Rod seal NR K20-PS K25-PS K32-PS K40-PS Since the seal kit does not include a grease pack, order it separately. Grease pack part number: GR-S-010 (10 g) e sure to read before handling. Refer to back cover for Safety Instructions. For ctuator and uto Switch Precautions, refer to andling Precaution for SMC Products and the Operation Manual on SMC website, Caution on andling/disassembly Warning 1. Do not rotate the cover. If a cover is rotated when installing a cylinder or screwing a fi tting into the port, it is likely to damage the junction part with cover. 2. In the case of exceeding the standard stroke length, implement an intermediate support. When using cylinder with longer stroke, implement an intermediate support for preventing the joint of rod cover and cylinder tube from being broken by vibration or external load. Precautions 63 Caution 1. void using the air cylinder in such a way that rotational torque would be applied to the piston rod. If rotational torque is applied, the non-rotating guide will become deformed, thus affecting the non-rotating accuracy. Refer to the table below for the approximate values of the allowable range of rotational torque. llowable rotational torque (N m or less) ø20 ø25 ø32 ø To screw a bracket or a nut onto the threaded portion at the tip of the piston rod, make sure to retract the piston rod entirely, and place a wrench over the fl at portion of the rod that protrudes. Tighten it by giving consideration to prevent the tightening torque from being applied to the non-rotating guide. 2. When replacing rod seals, please contact SMC. ir leakage may be happened, depending on the position in which a rod seal is fitted. Thus, please contact SMC when replacing them. 3. Not able to disassemble. Cover and cylinder tube are connected to each other by caulking method, thus making it impossible to disassemble. Therefore, internal parts of a cylinder other than rod seal are not replaceable. 4. Do not touch the cylinder during operation. Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 5. The oil stuck to the cylinder is grease. 6. The base oil of grease may seep out.

69 ir Cylinder: Direct Mount, Non-rotating Rod Type Series RK ottom Mounting Style RK ore size Stroke Z N Female rod end Female thread Thread depth 1 F FX FX F øi N Front Mounting Style Width across flats 1 ønd Width across flats K RK ore size Stroke Z Female rod end Width across flats K 4 x FF Width across flats 1 ønd 1 L 1 L X G G Y 2 x RcP 2 x RcP S + Stroke ZZ + Stroke Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x S + Stroke ZZ + Stroke G G 2 x øld ZZ + Stroke material of the workpiece. ore size Stroke range L 1 G G 1 I K L LD L LX N ND P S X Y ZZ 20 1 to ø5.5, ø9.5 counterbore depth M8 x / to ø6.6, ø11 counterbore depth M10 x / to ø9, ø14 counterbore depth M10 x / to ø11, ø17.5 counterbore depth M14 x / N LX L øi L N When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod end from being deformed depending on the Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK Female thread Thread depth 1 Female Rod End ore size 1 ZZ M4 x M5 x M6 x M8 x When female thread is used, use a thin wrench when tightening the piston rod. When female thread is used, use a washer etc. to prevent the contact part at the rod ZZ + Stroke end from being deformed depending on the material of the workpiece. ore size Stroke range L 1 F FF FX G G 1 I K N ND P S ZZ 20 1 to M5 x 0.8 depth M8 x / to M6 x 1 depth M10 x / to M6 x 1 depth M10 x / to M8 x 1.25 depth M14 x / uto Switch

70 Series uto Switch Mounting uto Switch Proper Mounting Position (Detection at stroke end) and Its Mounting eight Reed auto switch D-9 s 16 Solid state auto switch D-M9 D-M9 W D-M9 D-9 V 24.5 (22) ( ): Values for D-96 and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. s 22 (24) s 16 ( ): Values for D-M9 and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. s and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. D-M9 V D-M9 WV D-M9 V D-C7/C8/C73C/C80C s (22) ( ): Values for D-M9 V and are the dimensions from the end of the head cover/rod cover to the end of the auto switch. D-5/6/59W D-7 /7 W/7NF/7/7C s s D-33/34 D-G5NT s s 24.5 D-44 D-G39/K39 s s 65

71 uto Switch Mounting Series uto Switch Proper Mounting Position (Detection at stroke end) and Its Mounting eight uto Switch Proper Mounting Position uto switch model Note) djust the auto switch after confirming the operating condition in the actual setting. uto Switch Mounting eight uto switch model D-M9 (V) D-M9 W(V) D-M9 (V) D-9 D-M9 D-M9 W D-M9 D-9 (V) ore size D-9 V D-M9 V D-M9 WV D-M9 V D-5 D-64 D-59W D-G5NT D-7C D-C7/C8 D-C73C D-C80C D-C7 D-C80 D-7 D-7 W D-7 D-7NF D-5 D-6 D-C73C D-C80C D-59W D-3 D-G39 D-K39 D-44 ore size s s s s s s s D-G39 D-K39 D-3 D-44 D-7 D-7C D-7 W D-7 D-7NF D-G5NT Double cting, Double Rod W K KW RK R Direct Mount Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod uto Switch Direct Mount, Non-rotating Rod 66

72 Series uto Switch Proper Mounting Position (Detection at stroke end) and Its Mounting eight/single cting/spring Return Type (S), Spring Extend Type (T) uto Switch Proper Mounting Position: Type/Spring Return Type (S), Non-rotating Rod Type/Spring Return Type (S) uto switch model D-9 (V) D-M9 (V) D-M9 W(V) D-M9 (V) D-5 D-64 D-C7 D-C80 D-C73C D-C80C D-59W D-3 D-G39 D-K39 D-44 D-7 D-7C D-7 W D-7 D-7NF D-G5NT ore size dimensions Up to 50 st 51 to 100 st 101 to 150 st 151 to 200 st 201 to 250 st Note) djust the auto switch after confi rming the operating condition in the actual setting. uto Switch Proper Mounting Position: Type/Spring Extend Type (T), Non-rotating Rod Type/Spring Extend Type (T) uto switch model ore size D-9 (V) D-M9 (V) D-M9 W(V) D-M9 (V) D-5 D-64 D-C7 D-C80 D-C73C D-C80C D-59W D-3 D-G39 D-K39 D-44 D-7 D-7C D-7 W D-7 D-7NF D-G5NT dimensions Up to 50 st 51 to 100 st 101 to 150 st 151 to 200 st 201 to 250 st Note) djust the auto switch after confi rming the operating condition in the actual setting. 67

73 uto Switch Mounting Series Minimum Stroke for uto Switch Mounting Number of auto switches uto switch model With 2 pcs. With n pcs. With 1 pc. Different surfaces Same surface Different surfaces Same surface (n 2) D-M Note 1) 40 Note 1) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) D-M9 W Note 1) 40 Note 1) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) D-M Note 1) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) D Note 1) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) D-M9 V (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) D-9 V (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n D-M9 WV 2) (n 2) D-M9 V (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) D-C (n 2) D-C80 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) D-7 (n 2) D-7 W (n 2) D (n = 2, 4, 6 ) D-7NF (n = 2, 3, 4, 5 ) D-C73C D-C80C D-7C D-5 /64 D-G5NT D-59W D-3 Note 2) D-G39 D-K39 D-44 Note 1) uto switch mounting uto switch model Note 3) When n is an odd number, an even number that is one larger than this odd number is used for the calculation. Different surfaces With 2 auto switches (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n 2) 2 (n = 2, 4, 6 ) Note 3) (n = 2, 3, 4, 5 ) (n 2) (n = 2, 3, 4, 5 ) n: Number of auto switches Same surface (n 2) (n = 2, 3, 4, 5 ) Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount W K KW R The proper auto switch mounting position is 3.5 mm inward from the switch holder edge. Note 2) Minimum stroke for auto switch mounting in styles other than those in Note 1. The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. D-M9 D-M9 W Less than 20 stroke Note 2) Less than 55 stroke Note 2) D-M9 Less than 25 stroke Note 2) Less than 60 stroke Note 2) D-9 Less than 50 stroke Note 2) Operating Range uto switch model ore size D-9 (V) D-M9 (V) D-M9 W(V) D-M9 (V) D-C7 /C80 D-C73C/C80C Values which include hysteresis are for guideline purposes only, they are not a guarantee (assuming approximately ±30% dispersion) and may change substantially depending on the ambient environment. Note) The D-3 /44/G39/K39 cannot be mounted on the centralized piping type CDM2 P series. uto switch model ore size D-5 /64 D-3 /44 Note) D-59W D-7 /7 W/7 D-G5NT/7NF D-7C D-G39/K39 Note) Direct Mount, Non-rotating Rod RK uto Switch

74 Series uto Switch Mounting rackets/part No. uto switch model D-M9 (V) D-M9 W(V) D-9 (V) D-M9 (V) ore size ø20 ø25 ø32 ø40 M5-020 ( set of a, b, c, d) M5-020S ( set of b, c, d, e) M5-025 ( set of a, b, c, d) M5-025S ( set of b, c, d, e) M5-032 ( set of a, b, c, d) M5-032S ( set of b, c, d, e) M5-040 ( set of a, b, c, d) M5-040S ( set of b, c, d, e) Switch bracket (Resin) a Transparent (Nylon) Note 1) e White (PT) b Switch holder (Zinc) uto switch d uto switch mounting screw D-7 D-7 W D-7NF D-C7 /C80 D-C73C/C80C D-7 D-5 /64 D-59W D-G5NT D-G5N D-3 /44 Note 3) D-G39/K39 M2-020 ( set of band and screw) M2-020S ( set of band and screw) ( set of band and screw) M3-020 ( set of band and screw) c uto switch mounting band M2-025 ( set of band and screw) M2-025S ( set of band and screw) ( set of band and screw) M3-025 ( set of band and screw) M2-032 ( set of band and screw) M2-032S ( set of band and screw) ( set of band and screw) M3-032 ( set of band and screw) M2-040 ( set of band and screw) M2-040S ( set of band and screw) ( set of band and screw) M3-040 ( set of band and screw) Note 1) Since the switch bracket (made from nylon) are affected in an environment where alcohol, chloroform, methylamines, hydrochloric acid or sulfuric acid is splashed over, so it cannot be used. Please contact SMC regarding other chemicals. Note 2) void the indicator LED for mounting the switch bracket. s the indicator LED is projected from the switch unit, indicator LED may be damaged if the switch bracket is fixed on the indicator LED. Note 3) The D-3 /44/G39/K39 cannot be mounted on the CDM2 P series centralized piping type. and Mounting rackets Set Part No. Set part no. M2- (S) S: Stainless steel screw J4-1 J5-1 Contents uto switch mounting band (c) uto switch mounting screw (d) Switch bracket (White/PT) (e) Switch holder (b) Switch bracket (Transparent/Nylon) (a) Switch holder (b) 69 Other than the applicable auto switches listed in ow to Order, the following auto switches are mountable. Refer to the uto Switches Guide for the detailed specifications. Type Model Electrical entry Features Solid state Reed D-71, 72, 7 D-7NW, 7PW, 7W D-7 D-G5NT D-53, C73, C76 D-C80 Grommet (In-line) Grommet (In-line) With pre-wired connector is also available for solid state auto switches. For details, refer to the uto Switches Guide. Normally closed (NC = b contact) solid state auto switches (D-F9G/F9) are also available. For details, refer to the uto Switches Guide. Wide range detection type, solid state auto switch (D-G5N) is also available. For details, refer to the uto Switches Guide. Diagnostic indication (2-colour indication) Water resistant (2-colour indication) With timer Without indicator light

75 uto switch Prior to Use uto Switch Connection and Example Sink Input Specifications 3-wire, NPN 2-wire rown Input lack lue COM rown Input (PLC internal circuit) Source Input Specifications 3-wire, PNP 2-wire uto switch rown lack lue rown Input COM COM (PLC internal circuit) Double cting, Double Rod W uto switch uto switch lue lue COM Input (PLC internal circuit) (PLC internal circuit) Connect according to the applicable PLC input specifi cations, as the connection method will vary depending on the PLC input specifi cations. Example of ND (Series) and OR (Parallel) Connection When using solid state auto switches, ensure the application is set up so the signals for the fi rst 50 ms are invalid. 3-wire ND connection for NPN output 3-wire OR connection for NPN output (Using relays) (Performed with auto switches only) rown rown rown Relay Load lack lack Load lack uto switch 1 uto switch 1 uto switch 1 Load lue lue lue rown rown rown uto switch 2 lack uto switch 2 lack uto switch 2 lack lue lue lue Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod K KW 3-wire ND connection for PNP output (Using relays) rown Relay lack uto switch 1 lue (Performed with auto switches only) rown lack uto switch 1 lue 3-wire OR connection for PNP output rown lack uto switch 1 lue Direct Mount R uto switch 2 uto switch 1 uto switch 2 rown lack lue 2-wire ND connection rown lue rown lue Load Load When two auto switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up when both of the auto switches are in the ON state. uto switches with load voltage less than 20 V cannot be used. Load voltage at ON = Power supply voltage Residual voltage x 2 pcs. = 24 V 4 V x 2 pcs. = 16 V Example: Power supply is 24 VDC Internal voltage drop in auto switch is 4 V. rown lack Load uto switch 2 lue 2-wire OR connection uto switch 1 uto switch 2 rown lue rown lue Load uto switch 2 (Solid state) When two auto switches are connected in parallel, malfunction may occur because the load voltage will increase when in the OFF state. Load voltage at OFF = Leakage current x 2 pcs. x Load impedance = 1 m x 2 pcs. x 3 kω = 6 V Example: Load impedance is 3 kω. Leakage current from auto switch is 1 m. rown lack lue Load (Reed) ecause there is no current leakage, the load voltage will not increase when turned OFF. owever, depending on the number of auto switches in the ON state, the indicator lights may sometimes grow dim or not light up, due to the dispersion and reduction of the current fl owing to the auto switches. 70 Direct Mount, Non-rotating Rod RK uto Switch

76 Series Simple Specials/ Please contact SMC for detailed specifi cations, delivery and prices. The following special specifi cations can be ordered as a simplifi ed Made-to-Order. There is a specifi cation sheet available on paper and CD-ROM. Please contact your SMC sales representatives if necessary. ( type) Specifications Double acting Single acting Single rod Double rod Single rod Rubber ir Rubber ir Rubber Change of rod end shape Simple Specials -X0 to 30 -X6 Specifications eat resistant cylinder ( 10 to 150 C) Note1) ( type) Double acting Single acting Single rod Double rod Single rod Rubber ir Rubber ir Rubber -X7 -X9 -XC3 -XC4 -XC5 -XC6 -XC8 -XC9 -XC10 -XC11 -XC12 -XC13 -XC20 -XC22 -XC25 -XC27 -XC29 -XC35 -XC38 -XC52 -XC85 -X446 Cold resistant cylinder ( 40 to 70 C) Note1) Low speed cylinder (5 to 50 mm/s) Special port location With heavy duty scraper eat resistant cylinder ( 10 to 110 C) Note1) Made of stainless steel djustable stroke cylinder/djustable extension type djustable stroke cylinder/djustable retraction type Dual stroke cylinder/double rod type Dual stroke cylinder/single rod type Tandem cylinder uto switch rail mounting ead cover axial port Fluororubber seal No fixed orifice of connection port Double clevis and double knuckle joint pins made of stainless steel Double knuckle joint with spring pin With coil scraper Vacuum specification (Rod through-hole) Mounting nut with set screw Grease for food processing equipment PTFE grease Note 1) The products with an auto switch are not compatible. 71

77 Simple Specials/ Series K (Not-rotating rod type) Double acting Single rod Double rod Rubber ir Rubber ir K (Not-rotating rod type) Double acting Single rod Double rod Rubber ir Rubber ir R (Direct mount type) Double acting Single rod Rubber ir R (Direct mount type) Double acting Single rod Rubber ir RK (Direct mount, Non-rotating rod type) Double acting Single rod Rubber RK (Direct mount, Non-rotating rod type) Double acting Single rod Rubber Page Page 73 Page Page 75 Page 75 Page 75 Page 76 Double cting, Double Rod Single cting, Spring Return/Extend W Page 76 Page 77 Page 77 Page 77 Page 78 Page 78 Page 79 Page 80 Non-rotating Rod Double cting, Double Rod K KW Pages 80, 81 Page 82 Page 82 Page 83 Page 83 Direct Mount R Page 83 Page 84 Page 84 Page 84 Direct Mount, Non-rotating Rod RK Page 85 Page 85 uto Switch 72

78 Series Simple Specials These changes are dealt with Simple Specials System. Consult SMC. 1 Change of Rod End Shape pplicable Series -Z Series ction Precautions for change of rod end shape Double acting, Single rod X0 to 30 type Single acting (Spring return/extend) X0 to 30 W Double acting, Double rod X0 to 30 Non-rotating rod type K Double acting, Single rod X0,1,6,10,11,13,14,17,19,21 KW Double acting, Double rod X0,1,6,10,11,13,14,17,19,21 Direct mount type R Double acting, Single rod X0 to 30 Direct mount, Non-rotating rod type RK Double acting, Single rod X0,1,6,10,11,13,14,17,19,21 type (ir-hydro type) Double acting, Single rod X0 to 30 W Double acting, Double rod X0 to 30 -X0 to X30 Note 1. SMC will make appropriate arrangements if no dimension, tolerance, or fi nish instructions are given in the diagram. 2. dimensions marked with will be as follows to the rod diameter (D). Enter any special dimension you desire. D 6 D 1 mm, 6 < D 25 D 2 mm, D > 25 D 4 mm 3. In the case of double rod type and single acting retraction type, enter the dimensions when the rod is retracted. : 0 : 1 : 2 : 3 30 C C0.5 ød 30 T W1 : 4 : 5 : 6 : 7 ørd ørd L 30 L L W L L C0.5 file chamfer C W R sphere TP R sphere ødc 30 : 8 : 9 : 10 : T W1 73

79 Simple Specials Series : 12 : 13 : 14 : 15 C0.5 R sphere T ød W1 C ød 30 C L ød 30 C ød 30 Double cting, Double Rod W : 16 L ød 30 : : : Single cting, Spring Return/Extend C L K 30 L L L K C W ørd L L ød 30 L K ød 30 W L L 30 T L W : 20 : 21 ød T ød 30 : 22 ød ød T 30 : Non-rotating Rod Double cting, Double Rod K KW : 24 : 25 : 26 : 27 ød L 30 Direct Mount Direct Mount, Non-rotating Rod R RK : 28 : 29 : uto Switch T 74

80 Series Please contact SMC for detailed dimensions, specifi cations and lead times. 1 eat Resistant Cylinder ( 10 to 150 C) -X6 ir cylinder which changed the seal material and grease, so that it could be used even at higher temperature up to 150 from 10 C. pplicable Series Series Description Model ction Note -Z type Double acting, Single rod Except with auto switch W Double acting, Double rod Except with auto switch Non-rotating K Double acting, Single rod Except with auto switch rod type KW Double acting, Double rod Except with auto switch Direct mount type R Double acting, Single rod Except with auto switch Note 1) Operate without lubrication from a pneumatic system lubricator. Note 2) Please contact SMC for details on the maintenance intervals for this cylinder, which differ from those of the standard cylinder. Note 3) In principle, it is impossible to make built-in magnet type and the one with auto switch. ut, as for the one with auto switch, and the heat resistant cylinder with heat resistant auto switch, please contact SMC. Note 4) Piston speed is ranged from 50 to 500 mm/s. ow to Order model no. X6 Specifications mbient temperature range 10 C to 150 C Seals materials Fluororubber Grease eat resistant grease uto switch Not mountable Note) Dimensions Same as standard type Specifications other than above Same as standard type Note) Manufacturing built-in magnet type and the one with auto switch is impossible. Warning Precautions e aware that smoking cigarettes etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. eat resistant cylinder 2 Cold Resistant Cylinder ( 40 to 70 C) -X7 ir cylinder which changed the seal material and grease, so that it could be used even at lower temperature down to 40 C. pplicable Series Series Description Model ction Note -Z type Double acting, Single rod Except with air cushion and auto switch W Double acting, Double rod Except with air cushion and auto switch Direct mount type R Double acting, Single rod Except with air cushion and auto switch Note 1) Operate without lubrication from a pneumatic system lubricator. Note 2) Use dry air which is suitable for heatless air dryer etc. not to cause the moisture to be frozen. Note 3) Please contact SMC for details on the maintenance intervals for this cylinder, which differ from those of the standard cylinder. Note 4) Mounting auto switch is impossible. Note 5) No cushion type is adopted. Piston speed is ranged from 50 to 500 mm/s. ow to Order model no. X7 Specifications mbient temperature range 40 C to 70 C Seals materials Low nitrile rubber Grease Cold resistant grease uto switch Not mountable Note) Dimensions Specifications other than above Same as standard type Same as standard type Note) Manufacturing built-in magnet type and the one with auto switch is impossible. Warning Precautions e aware that smoking cigarettes etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. Cold resistant cylinder 3 Low Speed Cylinder (10 to 50 mm/s) -X9 Even if driving at lower speeds 10 to 50 mm/s, there would be no stick-slip phenomenon and it can run smoothly. pplicable Series Series Description Model ction Note -Z type Double acting, Single rod Except air-hydro, with air cushion, with rod boot Direct mount type R Double acting, Single rod Except with air cushion Specifications Piston speed Dimensions Specifications other than above ow to Order Warning model no. X9 Precautions 10 to 50 mm/s Same as standard type Same as standard type Note) Operate without lubrication from a pneumatic system lubricator. 75 Low speed cylinder e aware that smoking cigarettes etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans.

81 Series 4 Special Port Location D D Port C C Port -XC3 Compared with the standard type, a cylinder which changes the connection port location of rod/head cover and the location of cushion valve. pplicable Series Series Description Model ction Note -Z type 5 With eavy Duty Scraper Double acting, Single rod Single acting (Spring return/extend) W Double acting, Double rod ir-hydro type Double acting, Single rod Non-rotating rod type Direct mount type Direct mount type, ir-hydro type K Double acting, Single rod KW Double acting, Double rod R R Double acting, Single rod Double acting, Single rod Direct mount, Non-rotating rod type RK Double acting, Single rod Special port location Rod port location viewed from the rod side For port location, refer to the diagrams on the right and show the symbols of,, C and D. Except with air cushion ow to Order model no. XC3 ead port location viewed from the rod side Specifications: Same as standard type Port Location Corresponding symbol of mounting bracket (Positional relationships) Viewed from the rod side, the ports are rendered,, C, and D, in the clockwise direction. <Position relation between clevis and port> Viewed from the rod side, with the clevis positioned as shown in the diagram, the ports are rendered,, C, and D, in the clockwise direction. Positional relationships between port and cushion valve cannot be changed. -XC4 It is suitable for using cylinders under the environment, where there are much dusts in a surrounding area by using a heavy duty scraper on the wiper ring, or using cylinders under earth and sand exposed to the die-casted equipment, construction machinery, or industrial vehicles. pplicable Series Series Description Model ction Note -Z type Double acting, Single rod ow to Order model no. With heavy duty scraper (SC scraper) XC4 Construction (Dimensions are the same as standard.) Specifications: Same as standard type Caution Do not replace heavy duty scrapers. Since heavy duty scrapers are press-fi t, do not replace the cover only, but rather the entire rod cover assembly. The series cannot replace either heavy duty scraper or rod seal. Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount W Direct Mount, Non-rotating Rod K KW R RK uto Switch 76

82 Series 6 eat Resistant Cylinder ( 10 to 110 C) -XC5 Cylinder which changed the seal material for heat resistance (up to 110 C) in order to use under the severe ambient temperature condition which exceeds the standard specifi cations of 10 to 70 C. pplicable Series Series Description Model ction -Z type W Double acting, Double rod Double acting, Single rod Direct mount type R Double acting, Single rod ow to Order 7 Made of Stainless Steel -XC6 Suitable for the cases it is likely to generate rust by being immersed in the water and corrosion. pplicable Series Series Description Model ction -Z model no. type eat resistant cylinder W XC5 Double acting, Single rod Single acting (Spring return/extend) Double acting, Double rod Non-rotating rod type K Double acting, Single rod Direct mount type R Double acting, Single rod Specifications mbient temperature range 10 C to 110 C Seals materials Fluororubber uto switch Not mountable Note 2) Specifications other than above and external dimensions Note 1) Please contact SMC for details on the maintenance intervals for this cylinder, which differ from those of the standard cylinder. Note 2) Manufacturing built-in magnet type and the one with auto switch is impossible. Note 3) Material of rod boot is heat resistant tarpaulin. ow to Order model no. Specifications Parts changed to stainless steel Made of stainless steel Specifications other than above and external dimensions Same as standard type XC6 Piston rod, Rod end nut Same as standard type 8 djustable Stroke Cylinder/djustable Extension Type -XC8 It adjusts the extending stroke by the stroke adjustable mechanism equipped in the head side. (fter the stroke is adjusted, with cushion on both sides is altered to single-sided, with cushion.) pplicable Series Series Description Model ction Note -Z type Double acting Specifications Stroke adjustment symbol Stroke adjustment range 0 to 25 0 to 50 Specifications other than above Same as standard type ow to Order Mounting style ore size Stroke Cushion Rod end thread Z uto switch XC8 Warning Precautions 1. When the cylinder is operating, if something gets caught between the stopper bracket for adjusting the stroke and the cylinder body, it could cause bodily injury or damage the peripheral equipment. Therefore, take preventive measures as necessary, such as installing a protective cover. djustable stroke cylinder/djustable extension type djustable range Stroke adjustment symbol Stroke adjustment range 0 to 25 mm 0 to 50 mm 2. To adjust the stroke, make sure to secure the wrench fl ats of the stopper bracket by a wrench etc. before loosening the lock nut. If the lock nut is loosened without securing the stopper bracket, be aware that the area that joins the load to the piston rod or the area in which the piston rod is joined with the load side and the stopper bracket side could loosen fi rst. It may cause an accident or malfunction. Dimensions (Dimensions other than below are the same as standard type.) 77 Width across flats 3 Width across flats M 2 ømi MK MT Stroke ML + djustment M + Stroke + djustment ZZ + 2 x Stroke + djustment (: 25 mm, : 50 mm) 3 ore size 3 3 M MI MK 2 MT M ML ZZ M6x M8x M8x M10x

83 Series 9 djustable Stroke Cylinder/djustable Retraction Type The retracting stroke of the cylinder can be adjusted by the adjustment bolt. pplicable Series Series Description Model ction Note -Z type Double acting, Single rod ow to Order Caution Precautions Function DC D C stroke ZZ+Stroke+djustment (: 25 mm, : 50 mm) djustable range M+djustment M (djustment bolt) stroke stroke D C D C ore size M M ZZ 20 M10 x M14 x M14 x M16 x stroke -XC9 Specifications Stroke adjustment symbol Stroke adjustment range 0 to 25 0 to 50 Specifications other than above Same as standard type ore size Stroke Rod end thread Z uto switch XC9 1. When air is supplied to the cylinder, if the stroke adjustment bolt is 2. djust the stroke when the cylinder is not pressurised. loosened in excess of the allowable stroke adjustment amount, be If it is adjusted in the pressurised state, the seal of the adjustment aware that the stroke adjustment bolt could fly out or air could be section could become deformed, leading to air leakage. discharged, which could injure personnel or damage the peripheral equipment. Dimensions (Dimensions other than below are the same as standard type.) 10 Dual Stroke Cylinder/Double Rod Type -XC10 Two cylinders are constructed as one cylinder in a back-to-back confi guration allowing the cylinder stroke to be controlled in three steps. pplicable Series Series Description Model ction Note -Z type Double acting, Single rod Except with air cushion ow to Order Mounting style When air pressure is supplied to ports and, both and strokes retract. When air pressure is supplied to ports and C, out strokes. djustable stroke cylinder/djustable retraction type Mounting style ore size Stroke Stroke Z XC10 Dimensions (Dimensions other than below are the same as standard type.) Stroke adjustment symbol Stroke adjustment range 0 to 25 mm 0 to 50 mm Specifications Maximum manufacturable stroke 1000 Specifications other than above Same as standard type Dual stroke cylinder When air pressure is supplied to ports and D, out strokes. When air pressure is supplied to ports C and D, both strokes and out strokes. Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch port Stroke port GD C port GC S + Stroke ZZ + Stroke ( + ) Stroke S + Stroke port ore size GC GD S S ZZ

84 Series 11 Dual Stroke Cylinder/Single Rod Type -XC11 Two cylinders can be integrated by connecting them in line, and the cylinder stroke can be controlled in two stages in both directions. pplicable Series Series Description Model ction Note -Z type Double acting, Single rod Specifications: Same as standard type Please contact SMC for each manufacturable stroke length. ow to Order Mounting style ore size Stroke Stroke - Z XC11 Dual stroke cylinder/single rod type Dimensions (Dimensions other than below are the same as standard type.) C port port Stroke 0.5 Stroke port S + Stroke ZZ + Stroke (+) S + Stroke ore size S S ZZ Functional description of dual stroke cylinder stroke or stroke operation can be made individually. stroke C stroke 1) Initial state (0 stroke position) stroke C stroke stroke operation 1) Initial state (0 stroke position) stroke C 2) 1st stage ( stroke operation) When the air pressure is supplied from the port, the rod operates the stroke. stroke C 2) Operation When the air pressure is supplied from the port, the rod operates the stroke. - stroke C 3) 2nd stage (- stroke operation) Following the 1st stage, when the air pressure is supplied from the C port, the rod operates the - stroke. stroke C stroke stroke operation 1) Initial state (0 stroke position) stroke C stroke 4) Cylinder retraction When the air pressure is supplied from the port, the rod retracts completely. stroke C 2) Operation When the air pressure is supplied from the C port, the rod operates the stroke. Double output is possible. W W stroke stroke C stroke C 1) Initial state (0 stroke position) 2) Double output When the air pressure is supplied to the and C ports at the same time, the double output can be obtained in the stroke range. Caution Precautions 1. Do not supply air until the cylinder is fixed with the attached bolt. 2. If air is supplied without securing the cylinder, the cylinder could lurch, posing the risk of bodily injury or damage to the peripheral equipment. 79

85 Series 12 Tandem Cylinder This is a cylinder produced with two air cylinders in line allowing double the output force. pplicable Series Series Description Model ction Note -Z type Double acting, Single rod Except with air cushion ow to Order model no. port CDM2 Stroke S+Stroke ZZ+2xStroke 13 uto Switch Rail Mounting C port D port S+Stroke Port port When air pressure is supplied to ports and D, the output force is doubled in the retract stroke. When air pressure is supplied to ports and C, the output force is doubled in the out stroke. ore size S S ZZ XC13 cylinder on which a rail is mounted to enable auto switches, in addition to the standard method for mounting auto switches (and mounting type). pplicable Series Series Description Model ction Note -Z type W Double acting, Single rod Single acting (Spring return/extend) Double acting, Double rod Non-rotating rod type K Double acting, Single rod CDM2 pplicable uto Switches Rail mounting type Solid state Reed uto switch specifications Tandem cylinder XC12 Dimensions (Dimensions other than below are the same as standard type.) D-F7, D-F7 V, D-F7, D-F79F, D-F79W, D-F7 WV, D-J79, D-J79C, D-J79W D-9 /9 V, D-7/8, D-7 /80, D-73C/80C, D-79W For detailed specifications about an auto switch for itself, refer to uto Switches Guide. Specifications: Same as standard type Function ow to Order model no. XC13 XC13 XC13C Rail mounting direction Mounted on the right side when viewed from the rod with the ports facing upward. Mounted on the left side when viewed from the rod. Mounted on the underside when viewed from the rod. XC13 -XC12 Double cting, Double Rod Single cting, Spring Return/Extend Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod W K KW R RK uto Switch 80

86 Series 13 uto Switch Rail Mounting -XC13 uto Switch Proper Mounting Position (Detection at stroke end) and Its Mounting eight s uto Switch Proper Mounting Position (Detection at stroke end) uto switch model D-F7 /F79F/F7 V D-J79/J79C D-F7 W/J79W/F7 WV D-F7/F7V D-72/7 /80 D-73C/80C D-F7NT D-9 D-9 V D-79W ore size Note) djust the auto switch after confirming the operating conditions in the actual setting. Minimum Stroke for uto Switch Mounting uto switch model D-F7 V D-J79C D-F7 D-J79 D-F7 WV D-F7V D-79W D-F7 W/J79W D-F7 D-F79F/F7NT D-9 D-9 V D-7 /80 D-7 /80 D-73C/80C D-7 D-80 With 1 pc. No. of auto switch mounted With 2 pcs. Same surface D-7 D-80 Note) When n is an odd number, an even number that is one larger than this odd number is used for the calculation. owever, the minimum even number is 4. So, 4 is used for the calculation when n is 1 to 3. uto Switch Mounting rackets/part No. With n pcs. (n: No. of auto switches) Same surface (n 2) (n = 4, 6...) Note) (n 2) (n = 4, 6...) Note) (n 2) (n = 4, 6...) Note) (n 2) (n = 4, 6...) Note) (n 2) (n = 4, 6...) Note) (n 2) (n = 4, 6...) Note) (n 2) (n = 4, 6...) Note) uto Switch Mounting eight D-F7 /F79F D-J79/F7NT D-F7 W/J79W D-F7 D-9 /9 V 7 /80 D-F7 V D-F7 WV D-F7V D-J79C D-7 D-80 D-73C D-80C D-79W s s s s s s Operating Range uto switch model D-F7 /F79F/F7 V D-J79/J79C D-F7 W/J79W/F7 WV D-F7/F7V D-F7NTL ore size D-9 /D-9 V D-7 /80 D-7 /80 D-73C/80C D-79W Values which include hysteresis are for guideline purposes only, they are not a guarantee (assuming approximately ±30% dispersion) and may change substantially depending on the ambient environment. ore size uto switch model ø20 to ø40 D-9 /9 V Q2-012 Note 1) When adding D-9 (V), order a set of auto switch mounting brackets Q-1 and Q2-012 for the CDQ2 series (ø12 to ø25) separately. When adding the auto switches other than D-9 (V) mentioned on the left and D-F7(V), order auto switch mounting brackets Q-1 separately. Note 2) When adding the auto switch D-F7(V), order a stainless steel screw set 2 separately. 81

87 Series 14 ead Cover xial Port -XC20 ead side port position is changed to the axial direction. pplicable Series Series Description Model ction Note -Z type Non-rotating rod type K Double acting, Single rod Single acting (Spring return/extend) Double acting, Single rod Double acting, Direct mount type R Single rod Direct mount, Non-rotating rod type RK Double acting, Single rod ow to Order model no. Except with air cushion Except with air cushion Except with air cushion XC20 Specifications: Same as standard type Double cting, Double Rod Single cting, Spring Return/Extend W Construction 15 Fluororubber Seal ead cover axial port pplicable Series Series Description Model ction Note -Z type Double acting, Single rod W Double acting, Double rod Direct mount type R Double acting, Single rod ow to Order model no. Fluororubber seal XC22 Connection port oss-cut style Specifications Seal material mbient temperature range Specifications other than above and external dimensions ore size Port size 20, 25, 32 Rc Rc 1 4 Same dimensions as standard type except port size. Fluororubber -XC22 With auto switch Note1) : 10 C to 60 C (No freezing) Without auto switch : 10 C to 70 C Same as standard type Note 1) Please contact SMC, as the type of chemical and the operating temperature may not allow the use of this product. Note 2) Cylinders with auto switches can also be produced; however, auto switch related parts (auto switch units, mounting brackets, built-in magnets) are the same as standard products. efore using these, please contact SMC regarding their suitability for the operating environment. Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod K KW R RK uto Switch 82

88 Series 16 No Fixed Throttle of Connection Port -XC25 Type with no restrictor on the port, since it's using air-hydro type on the rod cover and the head cover of air cylinder series. pplicable Series Series Description Model ction -Z Except with air cushion ow to Order type Double acting, Single rod Non-rotating rod type K Double acting, Single rod model no. No fixed throttle of connection port Specifications: Same as standard type XC25 Construction (Dimensions are the same as standard.) Caution 1. Use a shock absorber etc. When the piston speed exceed 750 mm/s, make sure that direct impact does not apply on the cylinder cover by using an external stopper (shock absorber etc). 17 Double Clevis and Double Knuckle Joint Pins Made of Stainless Steel -XC27 To prevent the oscillating portion of the double clevis or the double knuckle joint from rusting, the material of the pin and the retaining ring is changed to stainless steel. pplicable Series Series Description Model ction -Z type Single acting (Spring return/extend) Double acting, Single rod Non-rotating rod type K Double acting, Single rod ow to Order D Double clevis type model no. Double clevis pin made of stainless steel XC27 Specifications Mounting style Pin and retaining ring material Specifications other than above Only double clevis type (D), double knuckle joint Stainless steel 304 Same as standard type Y CDP Double knuckle joint Clevis pin Knuckle pin 020, 032, 040 1, 2 Double knuckle joint pin made of stainless steel Clevis pin made of stainless steel Knuckle pin XC27 XC27 18 Double Knuckle Joint with Spring Pin -XC29 To prevent loosening of the double knuckle joint of standard air cylinder (Series /C2) pplicable Series Series Description Model ction Double acting, Single rod -Z type Single acting (Spring return/extend) W Double acting, Double rod Direct mount type R Double acting, Single rod ow to Order model no. XC29 Double knuckle joint with spring pin Specifications: Same as standard type Dimensions: For mounting bracket, pin is shipped together. (Dimensions other than below are the same as standard type.) Spring pin (ole dia.) (Shaft dia.) ZZ+Stroke ore size L1 ND10 NZ R Z ZZ Spring pin ø3 x 16L ø3 x 16L ø3 x 16L ø4 x 24L 83

89 Series 19 With Coil Scraper It gets rid of frost, ice, weld spatter, cutting chips adhered to the piston rod, and protects the seals etc. pplicable Series Series Description Model ction Note -Z type Double acting, Single rod Except with air cushion W Double acting, Double rod Except with air cushion 20 Vacuum (Rod through-hole) -XC38 Through-hole of hollow rod can be used as the passage of vacuum air. pplicable Series Series Description Model ction Note -Z type W Double acting, Double rod Except with air cushion ow to Order model no. With coil scraper Specifications: Same as standard type XC35 -XC35 Construction/Dimensions (Other dimensions are the same as standard.) Double cting, Double Rod Single cting, Spring Return/Extend W ow to Order model no. Specifications: Same as standard type ZZ + 2 x Stroke 3 x M4 x x exagon socket head set screw + Stroke 21 Mounting Nut with Set Screw -XC52 In order to prevent the mounting nut from being loosen, set screw should be tighten from the two directions to fi x the mounting nut. pplicable Series Series Description Model ction type -Z Non-rotating rod type Vacuum (Rod through-hole) W K KW ow to Order model no. XC38 Double acting, Single rod Single acting (Spring return/extend) Double acting, Double rod Double acting, Single rod Double acting, Double rod XC52 ore size d J ZZ 20 3 M5 x M5 x M5 x Rc1/ Dimensions (Dimensions other than below are the same as standard type.) Non-rotating Rod Double cting, Double Rod Direct Mount Direct Mount, Non-rotating Rod K KW R RK Mounting nut with set screw Specifications: Same as standard type uto Switch 84

90 Series 22 Grease for Food Processing Equipment -XC85 Food grade grease (certifi ed by NSF-1) is used as lubricant. pplicable Series Series Description Model ction Note -Z type ow to Order W Double acting, Single rod Single acting (Spring return/extend) Double acting, Double rod Direct mount type R Double acting, Single rod model no. XC85 Specifications mbient temperature range 10 C to 70 C Seals materials Nitrile rubber Grease Grease for food processing equipment uto switch Mountable Dimensions Same as standard type Specifications other than above Same as standard type Warning Precautions Grease for food processing equipment e aware that smoking cigarettes etc after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. Not installable zone Food zone...n environment where food which will be sold as merchandize, directly touches the cylinder s components. Splash zone...n environment where food which will not be sold as merchandize, directly touches the cylinder s components. Installable zone Non-food zone...n environment where there is no contact with food. Splash zone Not installable Food zone Not installable Food Container Note 1) void using this product in the food zone. (Refer to the figure on the right.) Note 2) When the product is used in an area of liquid splash, or a with water resistant function is required for the product, please consult with SMC. Note 3) Operate without lubrication from a pneumatic system lubricator. Note 4) Use the following grease pack for the maintenance work. GR--010 (Grease: 10 g) Note 5) Please contact SMC for details about the maintenance intervals for this cylinder, which differ from those of the standard cylinder. Non-food zone Installablele 23 PTFE Grease -X446 pplicable Series Series Description Model ction Note -Z ow to Order type Double acting, Single rod Direct mount type R Double acting, Single rod model no. X446 Specifications: Same as standard type Dimensions: Same as standard type When grease is necessary for maintenance, grease pack is available, please order it separately. GR-F-005 (Grease: 5 g) PTFE grease 85

Air Cylinder. New RoHS. Series CM2. Female rod end available as standard. Rod end styles suitable for the application can be selected.

Air Cylinder. New RoHS. Series CM2. Female rod end available as standard. Rod end styles suitable for the application can be selected. ir Cylinder ø 20, ø 25, ø 32, ø 40 New RoS Female rod end available as standard Selectable Rod end styles suitable for the application can be selected. Female thread Male thread Easy fine adjustment of

More information

Air Cylinder. New RoHS. Series CG1. Female rod end available as standard. Rod end styles suitable for the application can be selected.

Air Cylinder. New RoHS. Series CG1. Female rod end available as standard. Rod end styles suitable for the application can be selected. ir Cylinder ø 20, ø 25, ø 32, ø 40, ø 50, ø 63, ø 80, ø 100 New RoS Female rod end available as standard Selectable Rod end styles suitable for the application can be selected. Female thread Male thread

More information

10 % lighter kg. Air Cylinder kg. New. New. Series. Added ø 125 to standard type.

10 % lighter kg. Air Cylinder kg. New. New. Series. Added ø 125 to standard type. ir Cylinder New ø 3, ø 40, ø 50, ø 63, ø 80, ø 100, ø 15 10 % lighter RoS (ø 40-100 stroke) Weight Existing model New 1.01 kg Series dded ø 15 to standard type. 0.91 kg Reduced weight by changing the shape

More information

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added.

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added. ir Cylinder ø1, ø16 Double foot Double-side bossed added to the mounting types. 4 types 7 types Improved amount of mounting freedom Head cover with boss is added. Head flange are Double foot Double-side

More information

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types ir Cylinder Ø 6, Ø 1, Ø New RoS Double foot ead flange Double-side bossed added to the mounting types. 4 types 7 types New or Ø 6, 3 types are 6 types Double foot Double-side bossed ead flange ead cover

More information

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover.

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover. Air Cylinder 1 Series ø32, ø40, ø50, ø63, ø80, ø100, ø125 RoHS 10 (ø50-100 stroke) % lighter Current model 1.9 kg 1 Series 1.7 kg J 1 Reduced weight by changing the shape of the rod cover and head cover.

More information

% lighter. Air Cylinder. New. New RoHS. 1.31kg. Series CA2. Reduced weight by changing the shape of the rod cover and head cover.

% lighter. Air Cylinder. New. New RoHS. 1.31kg. Series CA2. Reduced weight by changing the shape of the rod cover and head cover. ir ylinder Ø 40, Ø 50, Ø 63, Ø 80, Ø 100 Reduced weight by changing the shape of the rod cover and head cover. Weight reduced by up to New RoS 15 (Ø 50-50 stroke) % lighter 1.31kg New 1.54 kg Existing

More information

10%lighter. 1.7 kg. 1.9 kg. Air Cylinder. New. Weight. Reduced weight by changing the shape of the rod cover and head cover. Series MB1 CAT.

10%lighter. 1.7 kg. 1.9 kg. Air Cylinder. New. Weight. Reduced weight by changing the shape of the rod cover and head cover. Series MB1 CAT. ir ylinder ø32, ø40, ø50, ø63, ø80, ø100, ø125 New RoS Weight (ø50-100 stroke) 10%lighter Existing model 1.9 kg New Series M1 1.7 kg Reduced weight by changing the shape of the rod cover and head cover.

More information

16% lighter Existing model

16% lighter Existing model ir Cylinder ø3, ø40, ø50, ø63, ø80, ø00 New RoS Weight (ø63-00 stroke) 6% lighter Existing model New Series.0 kg.69 kg Reduced weight by changing the shape of the rod cover and head cover. Series/ set

More information

10% lighter kg kg. Air Cylinder. MB Series. ø32, ø40, ø50, ø63, ø80, ø100, ø125

10% lighter kg kg. Air Cylinder. MB Series. ø32, ø40, ø50, ø63, ø80, ø100, ø125 ir Cylinder M Series ø3, ø40, ø50, ø63, ø80, ø00, ø5 RoHS 0% lighter CJ (ø40-00 stroke) Weight M Series 0.9 kg CJP CJ JCM CM Current model CM3 CG.0 kg CG3 JM Reduced weight by changing the shape of the

More information

Compact Cylinder. Series CQS CUJ CU CQS CQ2 RQ CQM MU

Compact Cylinder. Series CQS CUJ CU CQS CQ2 RQ CQM MU Compact Cylinder Series ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility for

More information

Air Cylinder. CG1 Series. Female rod end available as standard. Rod end types suitable for the application can be selected.

Air Cylinder. CG1 Series. Female rod end available as standard. Rod end types suitable for the application can be selected. ir Cylinder Series ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 RoHS emale rod end available as standard Rod end types suitable for the application can be selected. emale thread Easy fine adjustment of auto

More information

16% lighter kg. Air Cylinder kg. New. New. Weight. Reduced weight by changing the shape of the rod cover and head cover.

16% lighter kg. Air Cylinder kg. New. New. Weight. Reduced weight by changing the shape of the rod cover and head cover. ir Cylinder ø3, ø40, ø50, ø63, ø80, ø00 New RoS Weight (ø63-00 stroke) 6% lighter New Series Existing model.69 kg.0 kg Reduced weight by changing the shape of the rod cover and head cover. Series/ set

More information

Small Bore Hydraulic Cylinder

Small Bore Hydraulic Cylinder Small ore ydraulic Cylinder CN Series CQ CK CN CM CS C C D- CN Series Nominal pressure: MPa ore size :,,, Stainless Steel Tube Small ore ydraulic Cylinder for MPa CN Series ø, ø, ø, ø Equipped with cushion

More information

Air Cylinder: With End Lock. How to Order. Cylinder stroke (mm) (Refer to Standard Stroke on page 250.) H Head end lock. Rod boot. Nil.

Air Cylinder: With End Lock. How to Order. Cylinder stroke (mm) (Refer to Standard Stroke on page 250.) H Head end lock. Rod boot. Nil. Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 4-4 www.cmafh.com With auto switch F G C D U CM CDM With auto switch (uilt-in magnet) Mounting style asic style

More information

Small Bore Hydraulic Cylinder

Small Bore Hydraulic Cylinder Small ore ydraulic Cylinder CN Series CQ CK CN CM CS C C D- CN Series Nominal pressure: MPa ore size :,,, Stainless Steel Tube Small ore ydraulic Cylinder for MPa CN Series ø, ø, ø, ø Equipped with cushion

More information

Compact Cylinder/Plate type

Compact Cylinder/Plate type Compact Cylinder/Plate type Series :,,, Width: Reduced by up to % (compared with SMC series) Total length: Reduced by up to % Volume: Reduced by up to 1% Weight: Reduced by up to % (compared with SMC series

More information

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting.

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting. Compact Cylinder: Type Series ø, ø, ø, ø How to Order Without auto switch D With auto switch CDQS D FW S Number of auto switches L F G D, uilt-in magnet Mounting style Through-hole/oth ends tapped common

More information

Round Type Hydraulic Cylinder

Round Type Hydraulic Cylinder Round Type ydraulic Cylinder CM Series CQ CK C CM CS C C D- CM Series ominal pressure: 3. MPa ore size :,,, 3 3. MPa Round Type ydraulic Cylinder CM Series ø, ø, ø, ø pplicable uto Switches/Refer to pages

More information

CAT.ES20-85 F. Air Cylinder. ø125 newly introduced. Series MB. ø32,ø40,ø50,ø63,ø80,ø100,ø125

CAT.ES20-85 F. Air Cylinder. ø125 newly introduced. Series MB. ø32,ø40,ø50,ø63,ø80,ø100,ø125 M..3 : PM Page i CT.ES-8 F ir Cylinder ø newly introduced Series M ø,ø,ø,ø,ø,ø,ø Series M, MW, MK, Double acting single rod Double acting double rod Double acting non-rotating rod ø newly introduced (Double

More information

Air Cylinder. ø6, ø10, ø16. Easy installation. Reduced piston rod deflection

Air Cylinder. ø6, ø10, ø16. Easy installation. Reduced piston rod deflection ir Cylinder Series CJ2 ø, ø, ø CJ1 CJP Improved wear resistance The bearing portions of the rod cover and the clevis have been improved in wear resistance to ensure the longevity of the cylinder. Series

More information

Air Cylinder Series CG1

Air Cylinder Series CG1 ir Cylinder Series CG,,,,,,, Series Variations CJ Series Standard Series CG Substantially shorter length: to to mm (in comparison with Series CM) to to mm (in comparison with Series C), 9 to mm (in comparison

More information

2 way basic mounting: Through-hole or both ends tapped

2 way basic mounting: Through-hole or both ends tapped Compact Cylinder Series CQS ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility

More information

2 way basic mounting: Through-hole or both ends tapped

2 way basic mounting: Through-hole or both ends tapped Compact Cylinder Series ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility for

More information

Compact Guide Cylinder

Compact Guide Cylinder Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

Sine Cylinder. REC Series. ø20, ø25, ø32, ø40. Allows high speed transfer of work with dramatically reduced shock/impact. REA REB REC Smooth

Sine Cylinder. REC Series. ø20, ø25, ø32, ø40. Allows high speed transfer of work with dramatically reduced shock/impact. REA REB REC Smooth Sine Cylinder Series,,, llows high speed transfer of work with dramatically reduced shock/impact. RE RE RC Velocity curve Time Sine cylinder Current cylinder Sine Cylinder Series,,, llows rapid transfer

More information

Mini Free Mount Cylinder

Mini Free Mount Cylinder Mini Free Mount Cylinder Series ø, ø, ø, ø, ø, ø1, ø Series 1 ction Stroke 1 2 0 0 0 Clean uto switch series None Rod end Male threaded Without thread Solid state switch D-F D-M9 D-M9 W Female threaded

More information

Fine Lock Cylinder Double Acting, Single Rod. How to Order. Port thread type. Cylinder stroke (mm) Refer to Standard Stroke on page 718.

Fine Lock Cylinder Double Acting, Single Rod. How to Order. Port thread type. Cylinder stroke (mm) Refer to Standard Stroke on page 718. Courtesy of CM/lodyne/ydradyne Motion Control ydraulic Pneumatic lectrical Mechanical () - www.cmafh.com With auto switch With auto switch (uilt-in magnet) G C CM CM uilt-in Magnet Cylinder Model If a

More information

Air Cylinder Series CG1

Air Cylinder Series CG1 ir Cylinder Series CG,,,,,,, Series Variations CJ Series Standard Series CG Substantially shorter length: to to mm (in comparison with Series CM) to to mm (in comparison with Series C), 9 to mm (in comparison

More information

C85 (ISO 6432) Series: ø8, ø10, ø12, ø16, ø20, ø25 C75 Series: ø32, ø40

C85 (ISO 6432) Series: ø8, ø10, ø12, ø16, ø20, ø25 C75 Series: ø32, ø40 ISO Cylinder (ISO 6432) Series: ø8, ø10, ø12, ø16, ø20, ø25 Series: ø32, ø40 RoS Part numbers set for actuators with mounting brackets, rod end brackets and auto switches available. Now it is not necessary

More information

How to Order. Manual release type. Lock position. H Head end lock. With rod boot. Nil J K M9NWV M9NW H7C M9PWV M9PW M9BWV M9BW M9NAV M9NA M9PAV M9PA

How to Order. Manual release type. Lock position. H Head end lock. With rod boot. Nil J K M9NWV M9NW H7C M9PWV M9PW M9BWV M9BW M9NAV M9NA M9PAV M9PA Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - www.cmafh.com CDG1 With auto switch (uilt-in magnet) Mounting style asic style L xial foot style F Rod side

More information

Compact Cylinder: Standard Type Double Acting, Single Rod. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order. Piping A76H A72H 200 V

Compact Cylinder: Standard Type Double Acting, Single Rod. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order. Piping A76H A72H 200 V Compact Cylinder: Standard Type Double cting, Single Rod,,,,,,,,, How to Order Without auto switch D With auto switch CDQ2 D JW S uilt-in magnet Mounting style Through-hole (Standard) oth ends tapped style

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR2 CRU2 CR1 MSU CRJ Rotation 360 type MSQ 360 MSZ MSQ MRQ Series Variations Page Rotating angle 80 to 0 170

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator CRQ2 Series Rack & Pinion Type/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR 2 CR1 MSU CRJ CR1 CRQ2 MSQ MSZ Rotation 360 type 360 CRQ2 MSQ MRQ Series Variations Page Rotating angle

More information

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations.

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Free Mount Cylinder Series CU A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Space-saving The multiple surface direct mounting with a square

More information

Air Cylinder. ø6, ø10, ø16. Easy installation. Reduced piston rod deflection

Air Cylinder. ø6, ø10, ø16. Easy installation. Reduced piston rod deflection ir Cylinder eries ø, ø, ø Improved wear resistance The bearing portions of the rod cover and the clevis have been improved in wear resistance to ensure the longevity of the cylinder. eries Variations tandard

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm 360 type 360 CR2 CRU2 CR1 MSU CRJ CR1 MSQ MSZ MSQ MRQ Series Variations Standard Made to Order Rotating angle

More information

15% lighter. Air Cylinder. New. New. 1.31kg. Series CA2 CAT.ES20-222B. Reduced weight by changing the shape of the rod cover and head cover.

15% lighter. Air Cylinder. New. New. 1.31kg. Series CA2 CAT.ES20-222B. Reduced weight by changing the shape of the rod cover and head cover. ir ylinder ø40, ø50, ø63, ø80, ø100 Reduced weight by changing the shape of the rod cover and head cover. Weight reduced by up to ew RoS (ø63-50 stroke) 15% lighter 1.31kg ew 1.54 kg Existing model Easy

More information

66 mm 21% Air Cylinder Short Type. New RoHS. Compact with a new construction! New release with full functions. Series CM mm.

66 mm 21% Air Cylinder Short Type. New RoHS. Compact with a new construction! New release with full functions. Series CM mm. ir Cylinder Short Type Compact with a new construction! New release with full functions Minimized with shorter total length! Space saving; contributes to downsizing of equipment. Up to mm shorter mm Up

More information

3 Position Cylinder. RZQ Series. Provides intermediate stop mechanism. ø32, ø40, ø50, ø63. 2-stage stroke enabled with a small increase in length

3 Position Cylinder. RZQ Series. Provides intermediate stop mechanism. ø32, ø40, ø50, ø63. 2-stage stroke enabled with a small increase in length Position ylinder Series ø, ø, ø, ø Provides intermediate stop mechanism 2-stage stroke enabled with a small increase in length Overall length of cylinder tube DQ2 Full stroke First-stage stroke dditional

More information

Valve Mounted Cylinder Double Acting, Single Rod. How to Order. Electrical entry. L L plug connector M M plug connector. G Grommet

Valve Mounted Cylinder Double Acting, Single Rod. How to Order. Electrical entry. L L plug connector M M plug connector. G Grommet L F Mounting style asic style xial foot style Rod side flange style With auto switch CVJ L CDVJ L 6 6 How to Order pplicable uto Switches/Refer to pages to for further information on auto switches. Type

More information

Sine Cylinder. Series REC. ø20, ø25, ø32, ø40 REA REB REC C Y C X MQ RHC RZQ. Sine cylinder. Individual. Velocity curve. Speed. Conventional cylinder

Sine Cylinder. Series REC. ø20, ø25, ø32, ø40 REA REB REC C Y C X MQ RHC RZQ. Sine cylinder. Individual. Velocity curve. Speed. Conventional cylinder Sine Cylinder Series,,, llows high speed transfer of work with dramatically reduced shock/impact. Velocity curve RE RE Speed Time Sine cylinder Conventional cylinder 3 Sine Cylinder Series,,, llows rapid

More information

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil With auto switch RSG RSDG With auto switch (uilt-in magnet) uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the

More information

Round Type Hydraulic Cylinder

Round Type Hydraulic Cylinder Round Type ydraulic Cylinder Series CM CQ Series CM CK C CM CS C2 C ominal pressure: 3. MPa ore size :,,, 233 3. MPa Round Type ydraulic Cylinder Series C M ø, ø, ø, ø With uto Switch ow to Order CM L

More information

Compact Guide Cylinder Series MGQ

Compact Guide Cylinder Series MGQ Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø0 ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

22mm Space required between the bottom of the cylinder body and your equipment is reduced.

22mm Space required between the bottom of the cylinder body and your equipment is reduced. Compact Guide Cylinder ø2,,, ø2,,, ø0, ø63,, ø0 With air cushion Water resistant cylinder are now available. New Up to 7% Weight reduced! New Weight reduced by up to 7% with a shorter guide rod and thinner

More information

Air Cylinder: Standard Type Double Acting, Double Rod. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order. Bore size

Air Cylinder: Standard Type Double Acting, Double Rod. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order. Bore size Air Cylinder: tandard eries CG1W,,,,,,, 0 How to Order auto switch auto switch CG1W L N 0 With auto switch CDG1W L N 0 HW N A uilt-in magnet Double acting, double rod type L U Mounting style asic style

More information

Rod end male thread. With rubber bumper 056(9/16") 075(3/4") 106(1 1/16") 150(1 1/2") 250(2 1/2") 300(3")

Rod end male thread. With rubber bumper 056(9/16) 075(3/4) 106(1 1/16) 150(1 1/2) 250(2 1/2) 300(3) T.ID0-1 New ompact ylinder Series NQ8 ore size: 06(9/16 ),(/ ),106(1 1/16 ),(1 1/ ) 00( ),0( 1/ ),00( ),00( ) Now available in 00 ( ) and 00 ( ) bore sizes Standard type ctuation Style uilt-in magnet Rod

More information

Series RQ. The new standard for the future. Compact Cylinder with Air Cushion. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100

Series RQ. The new standard for the future. Compact Cylinder with Air Cushion. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 1 Compact Cylinder with ir Cushion ø, ø, ø, ø, ø, ø, ø, ø The new standard for the future J CQ U - NW ir Cushion Cylinder Uses a unique air cushion mechanism with no cushion ring. Size ø, ø and ø newly

More information

Non-rotating Double Power Cylinder. Double Power Cylinder MGZ. (without non-rotating MGJ MGP -Z MGP MGPW MGQ MGG MGC MGF MGT D- -X

Non-rotating Double Power Cylinder. Double Power Cylinder MGZ. (without non-rotating MGJ MGP -Z MGP MGPW MGQ MGG MGC MGF MGT D- -X Non-rotating Double Power Cylinder Double Power Cylinder (without non-rotating Series Series R mechanism) MGJ -Z W MGQ MGG MGC MGF MGT 23 D- -X Non-rotating Double Power Cylinder Double extension output

More information

MGZ. Non-rotating Double Power Cylinder. Double Power Cylinder MGJ MGP MGPW MGQ MGG MGC MGF MGT D- -X

MGZ. Non-rotating Double Power Cylinder. Double Power Cylinder MGJ MGP MGPW MGQ MGG MGC MGF MGT D- -X Non-rotating Double Power Cylinder Double Power Cylinder (without non-rotating Series Series R mechanism) 23 MGJ -Z W MGQ MGG MGC MGF MGT D- -X Tube rod diameter External dimension Non-rotating Double

More information

Compact Cylinder. With a short overall length, the space saving cylinder helps to make various jigs and equipment more compact.

Compact Cylinder. With a short overall length, the space saving cylinder helps to make various jigs and equipment more compact. Compact Cylinder Series CQ ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø1, ø With a short overall length, the space saving cylinder helps to make various jigs and equipment more compact. Variations Standard Series

More information

Compact Slide. Series MXH ø6, ø10, ø16, ø20

Compact Slide. Series MXH ø6, ø10, ø16, ø20 Compact Slide Series ø, ø, ø, ø The use of an endless track linear guide produces a table cylinder having excellent rigidity, linearity and non-rotating accuracy. Endless track linear guide Series Variations

More information

Toggle Type Air Gripper

Toggle Type Air Gripper ø2, ø40, ø50, ø6 Ideal for gripping heavy workpiece Toggle mechanism is adopted. Holds workpiece even when pressure drops. The toggle mechanism that activates when the finger closes realizes strong and

More information

Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43

Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43 CAT.EUS- B -UK Free Mount Cylinder A space-saving air cylinder with multiple surfaces capable of direct mounting. Offered in many variations. Space-saving The multiple surface direct mounted rectangular

More information

Double Power Cylinder. Non-rotating Double Power Cylinder. Series MGZ. Series MGZR (without MGJ MGP MGQ MGG MGC MGF MGZ MGT. non-rotating mechanism)

Double Power Cylinder. Non-rotating Double Power Cylinder. Series MGZ. Series MGZR (without MGJ MGP MGQ MGG MGC MGF MGZ MGT. non-rotating mechanism) Non-rotating Double Power Cylinder Series Double Power Cylinder Series R (without non-rotating mechanism) 2 Non-rotating Double Power Cylinder Double extension output power!! Our unique construction doubles

More information

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping.

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping. Dual Rod Cylinder / Series ø,,,,, Dual rod cylinder with guide function suitable for pick & place applications. Ball bushing bearings and slide bearings are standard for all series. Dimensions for ball

More information

Hygienic Design Cylinder

Hygienic Design Cylinder CT.EUS- -UK Hygienic Design Cylinder New Round type Series HY has been added. water resistant cylinder configured for easy cleaning ISO standard type Series HYC asic type Series HYQ With guide Series HYG

More information

How to Order. Nil M. Action S T. Load voltage Wiring. M9NV 5 V, 12 V 3-wire (PNP) M9PV 12 V. F9NWV 5 V, 12 V 3-wire (PNP) F9PWV

How to Order. Nil M. Action S T. Load voltage Wiring. M9NV 5 V, 12 V 3-wire (PNP) M9PV 12 V. F9NWV 5 V, 12 V 3-wire (PNP) F9PWV ompact ylinder: Standard Type Single cting, Single Rod, Spring Return/Extend Series QS ø, ø, ø, ø How to Order QS S QS S FWV S uilt-in magnet Mounting style Through-hole/oth ends tapped common (Standard)

More information

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8 Precision Cylinder Series, ø, ø6, ø, ø, ø, ø MXS Series Variations Model 8 Standard stroke (mm) 7 7 Rod end configuration Cushion Rubber bumper End lock Made to Order Rod Variable stroke/ through-hole

More information

Series C85. ISO Cylinder. Conforming to ISO 6432 and CETOP RP52P. ø8, ø10, ø12, ø16, ø20, ø25

Series C85. ISO Cylinder. Conforming to ISO 6432 and CETOP RP52P. ø8, ø10, ø12, ø16, ø20, ø25 ISO Cylinder Series C ø, ø0, ø, ø, ø, ø Conforming to ISO and CETOP RPP. Series Variations Standard Series C Series Non-rotating rod Series C ction Double acting Single acting Double acting Rod Single

More information

Pin Cylinder. Series CJP. Double Acting/Single Acting Spring Return. Standard Variation Built-in Magnet. Single Rod. Single Rod Spring return

Pin Cylinder. Series CJP. Double Acting/Single Acting Spring Return. Standard Variation Built-in Magnet. Single Rod. Single Rod Spring return Pin Cylinder eries ouble cting/ingle cting pring Return Variations eries tandard tyle eries With uto witch ouble cting (Non-lube) ingle cting (Non-lube) ction ingle Rod ingle Rod pring return tandard Variation

More information

Fine Lock Cylinders/Lock-up Cylinder

Fine Lock Cylinders/Lock-up Cylinder Fine Lock Cylinders/Lock-up Cylinder CL Series,,, 3,,, 3,,,,, CLJ Locking method Features Spring locking Unlocking Discharging the air causes the lock to operate. (Lock-up cylinders are spring locking

More information

15% lighter. Air Cylinder. 1.31kg. CA2 Series. Reduced weight by changing the shape of the rod cover and head cover. Weight reduced by up to

15% lighter. Air Cylinder. 1.31kg. CA2 Series. Reduced weight by changing the shape of the rod cover and head cover. Weight reduced by up to Air ylinder A Series ø40, ø50, ø63, ø80, ø100 RoHS Reduced weight by changing the shape of the rod cover and head cover. Weight reduced by up to (ø50-50 stroke) 15% lighter 1.31kg Easy air cushion control

More information

3 Position Cylinder. ø32, ø40, ø50, ø63 RZQ CDQ2. Bore size (mm)

3 Position Cylinder. ø32, ø40, ø50, ø63 RZQ CDQ2. Bore size (mm) Position ylinder Series ø, ø, ø, ø Provides intermediate stop mechanism 2-stage stroke enabled with a small increase in length Overall length of cylinder tube First-stage stroke Full stroke dditional cylinder

More information

Plate Cylinder. MU Series. It is possible to mount small auto switches in 4 directions. No stick-out Easy mounting. ø25, ø32, ø40, ø50, ø63

Plate Cylinder. MU Series. It is possible to mount small auto switches in 4 directions. No stick-out Easy mounting. ø25, ø32, ø40, ø50, ø63 Plate Cylinder MU Series ø, ø, ø, ø, ø It is possible to mount small auto switches in 4 directions. No stick-out Easy mounting RoHS Small auto switch CUJ CU CQS JCQ CQ2 Reduction of labor for work RQ CQM

More information

Compact Guide Cylinder

Compact Guide Cylinder Compact Guide Cylinder Series ø2, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Series standard type and series high precision ball bushing bearing type (except with end lock) products have been remodeled for a lightweight

More information

Guide Table. ø40, ø63, ø100

Guide Table. ø40, ø63, ø100 Guide Table Series MGF ø, ø, ø Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Compact Hydraulic Cylinder

Compact Hydraulic Cylinder ompact Hydraulic ylinder Series HQ HQ Series HQ HK HN HM HS H2 H Nominal pressure:. MPa ore size :,,,,,, . MPa ompact Hydraulic ylinder Double cting/single Rod Series H Q ø, ø, ø, ø, ø, ø, ø With uto Switch

More information

Compact Cylinder With Solenoid Valve

Compact Cylinder With Solenoid Valve Compact Cylinder With Solenoid Valve Series ø, ø, ø, ø Valve and compact cylinder integrated for compactness Solenoid valve abor saving No need to select size of valve ess piping work Compact cylinder

More information

High Power Cylinder. Series RHC. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 REA REB REC C Y C X MQ RHC RZQ D- -X

High Power Cylinder. Series RHC. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 REA REB REC C Y C X MQ RHC RZQ D- -X ourtesy of M/Flodyne/Hydradyne Motion ontrol Hydraulic Pneumatic Electrical Mechanical () 46-4 www.cmafh.com High Power ylinder ø, ø, ø3, ø4, ø, ø, ø, ø 33 RE RE RE Y X RH ourtesy of M/Flodyne/Hydradyne

More information

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping.

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping. Dual Rod Cylinder J/ Series ø, ø, ø, ø, ø, Dual rod cylinder with guide function suitable for pick & place applications. Ball bushing bearings and slide bearings are standard for all series. Dimensions

More information

Air Cylinder. ø125, ø140, ø160, ø180, ø200, ø250, ø300. Lube. Single rod. Non-lube. Series. Air-hydro. Lube. Double rod. Non-lube CS1W.

Air Cylinder. ø125, ø140, ø160, ø180, ø200, ø250, ø300. Lube. Single rod. Non-lube. Series. Air-hydro. Lube. Double rod. Non-lube CS1W. Air ylinder Series S,,,,,, Series Variations Series Action asic Standard variations Page J JP J Standard Series S Series S Double acting Single rod Series S Double rod Series SW 4 4 M G M M A S S Series

More information

Lube, Non-lube: ø125, ø140, ø160, ø180, ø200, ø250, ø300 Air-hydro: ø125, ø140, ø160. How to Order. Bore size. 125mm 140mm 160mm

Lube, Non-lube: ø125, ø140, ø160, ø180, ø200, ø250, ø300 Air-hydro: ø125, ø140, ø160. How to Order. Bore size. 125mm 140mm 160mm ir Cylinder/tandard eries C, : ø, ø, ø, ø, ø, ø, ø : ø, ø, ø How to Order B L F G C D T C L Mounting Foot Front flange Rear flange ingle clevis Double clevis Center trunnion JR Rod boot/cushion Rod boot

More information

Square Tube Type Air Cylinder

Square Tube Type Air Cylinder Standard: Double cting Single Rod Series C6 Square Tube Type ir Cylinder Series 1 ø, ø, ø, ø, ø, ø Single rod type Series 1 Double rod type Series 1W Non-rotating rod type Series 1K CJ1 CJP CJ2 CM2 C8

More information

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder.

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder. Compact Guide Cylinder Series ø2,,, ø2,,, ø, ø63,, ø0 Up to Weight reduced by up to 24% with a shorter guide rod and thinner plate 24% Weight reduced! 3 types of bearing can be selected. Slide bearing

More information

Guide Table. MGF Series

Guide Table. MGF Series Guide Table MGF Series ø, ø, ø0 Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Rotary Clamp Cylinder

Rotary Clamp Cylinder Rotary Clamp Cylinder ø, ø, ø, ø, ø, ø, ø, ø llowable moment of inertia 3 times higher New structure! New series Overall length is the same as the existing products! Mounting dimensions are interchangeable

More information

Compact Guide Cylinder Series MGP

Compact Guide Cylinder Series MGP Compact Guide Cylinder Series MGP ø2, ø, ø, ø, ø, ø, ø, ø,, ø0 MGJ MGP MGQ MGG MGC MGF MGZ MGT Series Variations Series Bearing type Cushion 2 0 Page Standard type MGP With air cushion MGP With end lock

More information

Reduced by Max. 58% Maximum allowable stroke when using clevis bracket CS2 CS Stroke (mm)

Reduced by Max. 58% Maximum allowable stroke when using clevis bracket CS2 CS Stroke (mm) ir ylinder 7. kg eight Reduced by Max. 58% ew arge ore Sizes ø15, ø, ø ighter installation achieved by reducing weight. Die cast rod cover and head cover used to achieve greater weight reduction. Rod bore

More information

Rotary Clamp Cylinder

Rotary Clamp Cylinder Rotary Clamp Cylinder ø, ø, ø, ø, ø, ø, ø, ø llowable moment of inertia 3 times higher New structure! New series Overall length is the same as the existing products! Mounting dimensions are interchangeable

More information

High Power Cylinder. Series RHC. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 REA REB REC C Y C X MQ RHC RZQ. Individual

High Power Cylinder. Series RHC. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 REA REB REC C Y C X MQ RHC RZQ. Individual High Power ylinder Series RH ø, ø, ø, ø, ø, ø3, ø, ø RE RE RE Y X RH D- -X -X High power cylinder: Smooth cushioning for high speed operation (3 low/medium speed operation with heavy loads The capacity

More information

1.56 L INEAR A CTUATORS: AIR C YLINDERS S ERIES CA1

1.56 L INEAR A CTUATORS: AIR C YLINDERS S ERIES CA1 1.56 L INEAR A CTUATORS: AIR C YLINDERS A IR C YLINDER Auto switch sensing optional s Ø4, 5, 63, 8, 1 Non-rotating piston rod & double rod types available Ultra low friction, maximum 5% Long life, high

More information

Series MBB ø32, ø40, ø50, ø63, ø80, ø100

Series MBB ø32, ø40, ø50, ø63, ø80, ø100 Air Cylinder/End ock Series ø, ø, ø, ø, ø, ø ow to Order Standard ith auto switch MD A F G C D T uilt-in magnet Mounting asic/ithout bracket Axial foot Front flange Rear flange Single clevis Double clevis

More information

ISO Standard Hydraulic Cylinder

ISO Standard Hydraulic Cylinder ISO Standard ydraulic ylinder Series S/SG Series S Q N Nominal pressure: S Pa ore size :,,,, Related quipment Series SG Nominal pressure: - Pa ore size : 3,,,,, 51 ISO Standard ydraulic ylinder Series

More information

ACS2 series. KCC Co., Ltd. PNEUMATIC & HYDRAULIC. ACS2 series. For more info visit us : ACS2 - N LB 32 - S 100

ACS2 series. KCC Co., Ltd. PNEUMATIC & HYDRAULIC. ACS2 series. For more info visit us :  ACS2 - N LB 32 - S 100 KCC Co., Ltd. Symbol Features With auto switch, rubber bumper (Standard). improves lateral load resistance. Double Acting / Single Rod Double Acting / Double Rod Single Acting / Spring Return Single Acting

More information

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP CT.S-7 C Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 New end lock type introduced to Series . Top mount Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Four mounting types

More information

Rotary Actuated Air Gripper

Rotary Actuated Air Gripper Rotary ctuated ir Gripper MHR, MDHR/MHR3, MDHR3 -finger type: Size, 15,, 3/ 3-finger type: Size, 15 High Precision - Repeatability ±.1 mm Parallel opening and closing mechanism utilizing a cross roller

More information

Compact Cylinder. With a short overall length, the space-saving cylinder helps to make various jigs and equipment more compact.

Compact Cylinder. With a short overall length, the space-saving cylinder helps to make various jigs and equipment more compact. Compact Cylinder Series CQ ø, ø, ø, ø, ø, ø, ø, ø3, ø, ø, ø, ø1, ø, ø, ø With a short overall length, the space-saving cylinder helps to make various jigs and equipment more compact. Series Variations

More information

Guide Cylinder MGG. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. Integration of a basic cylinder and guide rods

Guide Cylinder MGG. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. Integration of a basic cylinder and guide rods Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Guide Cylinder Series MGG ø, ø, ø, ø, ø, ø, ø, ø Integration of a basic cylinder and guide

More information

Rotary Actuator. New RoHS. New. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB 2. Standard type/series CRB2

Rotary Actuator. New RoHS. New. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB 2. Standard type/series CRB2 Rotary Actuator Vane Type 1, 15, 2, 3, 4 Standard Type Free Mount Type Many combinations available! Standard type/series Piping ports are located on the flat surface. Fittings can be secured firmly, piping

More information

Compact Cylinder Remodeled with a new body to get more flexibility! Can mount small auto switches on 4 surfaces.

Compact Cylinder Remodeled with a new body to get more flexibility! Can mount small auto switches on 4 surfaces. Compact Cylinder Remodeled with a new body to get more flexibility! Can mount small auto switches on 4 surfaces. New uto switches can be mounted on any of the 4 surfaces, depending on the installation

More information

Guide Table. Series MGF

Guide Table. Series MGF Guide Table Series MGF ø, ø, ø0 Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Air Cylinder. ø125, ø140, ø160, ø180, ø200, ø250, ø300. Lube. Single rod. Non-lube. Series. Air-hydro. Lube. Double rod. Non-lube CS1W.

Air Cylinder. ø125, ø140, ø160, ø180, ø200, ø250, ø300. Lube. Single rod. Non-lube. Series. Air-hydro. Lube. Double rod. Non-lube CS1W. Air ylinder Series S,,,,,, Series Variations Series Action asic Standard variations Page J JP J Standard Series S Series S Double acting Single rod Series S Double rod Series SW 4 M G M M A S S Series

More information

Compact Cylinder. ISO Standard (21287) C55 Series. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. RoHS C85 C75 C96 C96Y C96K C55

Compact Cylinder. ISO Standard (21287) C55 Series. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. RoHS C85 C75 C96 C96Y C96K C55 55 96Y 96K 96 P96K P96 75R 75K-S/T 75K 75-S/T 75W 75 85R 85K-S/T 85K 85-S/T 85W 85 ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Related ade to uto Products Order Switch ompact ylinder 55 Series ISO Standard

More information

Air Cylinder: With End Lock. How to Order. Port thread type. Cylinder stroke (mm) For more information, please refer to the next page.

Air Cylinder: With End Lock. How to Order. Port thread type. Cylinder stroke (mm) For more information, please refer to the next page. ir Cylinder: With End ock Series C ø, ø, ø, ø, ø Without auto switch With auto switch F G C D T With auto switch Mounting style asic style xial foot style Rod side flange style Head side flange style Single

More information

Lube. Single rod. Non-lube CS1. series. Air-hydro. Lube. Double rod CS1W series. Non-lube. Non-lube

Lube. Single rod. Non-lube CS1. series. Air-hydro. Lube. Double rod CS1W series. Non-lube. Non-lube Air ylinder S Series,,,,,, J Series Variations Series Action asic Standard variations Page JP J JM Standard S Series S Series Double acting Single rod S series Double rod SW series 5 548 M M3 G G3 JM M

More information

Hygienic Design Cylinder

Hygienic Design Cylinder ygienic Design ylinder Series Y water resistant cylinder configured for easy cleaning Series Y ISO standard type Series Y asic type Series YQ With guide Series YG J G Y Series 0 0 External seal material

More information

Magnetically Coupled Rodless Cylinder Slider Type: Ball Bushing Bearing. How to Order CY1L 25 H 300 J79W. Load voltage 5 V 200V 100 V 12 V 5 V, 12 V

Magnetically Coupled Rodless Cylinder Slider Type: Ball Bushing Bearing. How to Order CY1L 25 H 300 J79W. Load voltage 5 V 200V 100 V 12 V 5 V, 12 V Magnetically Coupled Rodless Cylinder Slider Type: all ushing earing Series CY1L ø, ø, ø, ø, ø, ø, ø How to Order CY1L H 00 J79W Slider type (all bushing bearing) mm mm mm mm mm mm mm Magnetic holding

More information

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g.

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g. Compact Slide Series ø, ø, ø, ø RoHS Allowable moment MXS Improved by up to MXQ MXQ 2% MXF MXW MXJ MXP MXY With new high rigidity linear guide MTS Allowable moment improvement illustrated below Allowable

More information