Compact Cylinder Remodeled with a new body to get more flexibility! Can mount small auto switches on 4 surfaces.

Transcription

1 Compact Cylinder Remodeled with a new body to get more flexibility! Can mount small auto switches on 4 surfaces. New uto switches can be mounted on any of the 4 surfaces, depending on the installation conditions. (ø to ø2: 2 surfaces) Improved flexibility of system design. ø to ø uto switch mounting rail removed round slot for mounting small auto switches is provided on 4 surfaces. NW ø to ø xisting model ø to ø : Only one surface ø to ø2 NW vailable up to ø uto switch rail ø to ø2: ountable on 2 surfaces Rail mounting type auto switch Small auto switch 2 switches can be mounted on the same surface. (ø: One slot for each surface) No projection of auto switch Prevention of damage to auto switch Sleeves cannot get caught in the auto switch and its mounting rail. Improved ease of work and safety Reduction in labor for design There is no need to check for interference with a machine, because the outer dimensions of the cylinder do not change when the auto switch is mounted. NW xclusive bodies (-) for ø to ø intermediate strokes ( st or more) now kept in inventory*, enabling shorter delivery times. * Formerly produced upon receipt of order Series CQ2 xisting model ø to ø Stroke stroke Currently stocked intermediate stroke CT.S-

2 NW Series CQ2 Compact Cylinder Reduced by to % NW (Compared with SC CQ2 series) xisting model ighter weight The body strength (kinetic energy, allowable load, withstand pressure, etc.) is the same as the existing product. Contribution to environment and ecology Reduction of CO2 discharge by t by less use of aluminum Weight (Stroke mm, built-in magnet, female thread and with rubber bumper) Stroke NW CQ2 xisting model CQ2 ø- st 4(43) 43(2) (g) ( ): With male thread Small auto switch 2-color indication solid state auto switch ppropriate setting of the mounting position can be performed without mistakes. Operating range ON Red Green Red OFF green light lights up at the optimum operating range. Optimum operating range ven if 2-color indication solid state auto switches are fixed at the optimum operating range (the green light lights up), the operation may become unstable depending on the installation environment or magnetic field disturbance. (agnetic body, external magnetic field, proximal installation of cylinders with built-in magnet and actuators, temperature change, other factors for magnetic force fluctuation during operation, etc.) For general environments Water resistant type For environments exposed to water and coolant agnetic field resistant type For use with C spot welders, which generate strong magnetic field D-W(V) Features 1 D-(V) D-P3DW

3 Reduction in labor for work Reduction in number of components No loss of components uto switch NW 1 Insert the auto 2 Fix the auto switch. switch. Takes a lot of labor and time xisting model because there are many components. Highly likely to lose components uto switch The nuts and screws may fall out when installed vertically. uto switch The nut falls out! The auto switch can be replaced with the foot brackets mounted. Reduction in labor for design uto switch NW The bracket does not interfere with the slot. xisting model The bracket interferes with the slot. uto switch Port side uto switch side uto switch side Port side Port side and auto switch side are near each other for easy handling. The rail mounting type auto switch can be mounted. Refer to page 14 for further information on auto switch mounting bracket. uto switch mounting screw uto switch uto switch fixing screw uto switch spacer uto switch mounting nut uto switch mounting screw uto switch uto switch mounting nut Features 2

4

5 Compact Cylinder Series CQ2 ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø, ø, ø1, ø, ø1, ø With a short overall length, the space-saving cylinder helps to make various jigs and equipment more compact. Series Variations Series ction Type stroke Page arge ore NW arge ore NW Double acting Single acting Double acting Single rod CQ2 Double rod CQ2W Spring return/ Spring extend CQ2 Single rod CQ2 Double rod CQ2W ø, ø: to 3 ø, ø2: to ø, ø: to ø to ø: to ø, ø: to 3 ø, ø2: to ø, ø: to ø to ø: to ø to ø:, ø:, to 3 to ong Stroke Rod xial Piping ong Stroke NW Rod NW xial Piping (Centralized piping type) Double acting Double acting Double acting Single acting Single rod CQ2 Single rod CQ2K Double rod CQ2KW Single rod CQP2 Spring return/ Spring extend CQP2 to 3 ø, ø: to 3 ø, ø2: to ø, ø: to ø, ø: to ø, ø: to 3 ø, ø2: to ø, ø: to ø, ø: to ø, ø: to 3 ø, ø2: to ø, ø: to ø to ø: to ø to ø:, ø:, nti-lateral oad With nd ock Water Resistant nti-lateral oad NW With nd ock Double acting Single rod CQ2S ø to ø: to ø to ø: to With uto Switch Water Resistant NW Smooth Cylinder (ow friction) CQ2Y Double acting Double acting Single rod CQ2 Single rod CQ2 R V Refer to est Pneumatics No. 3. ow-speed Cylinder CQ2 ø to ø: to ø, ø: 2 to 1 ø, ø2: to ø, ø: to ø to ø: to Refer to est Pneumatics No. 3. uto Switch ade to Order Front matter 1

6 Combinations of Products and ade Series CQ2 to Order Specifications Series CQ2 : : ade to Order : Special product (For details, please contact SC.) : Not available ade to Order: For details, refer to pages 1 to. Symbol D CQ2 CQ2- CQ2-C CQ2-F CQ2F F CQ2 G CQ2D CQ2H -, - - R CQ2 V Note ) C4 C C C C C C2 Specifications product uilt-in magnet oth ends tapped With rubber bumper With boss on head end With one-touch fittings Foot/Flange Double clevis ir-hydro type Clean series Copper and fluorine-free series Water resistant Heat resistant cylinder ( to 1 C) Cold resistant cylinder ( to C) ow-speed cylinder ( to mm/s) Intermediate stroke (xclusive body type) Intermediate stroke (Spacer-installed type) ong stroke (ir-hydro type only) ow-speed cylinder ( to mm/s) Cylinder with heat resistant auto switch With heavy-duty scraper Piston rod/retaining ring/rod end nut material: Stainless steel djustable stroke cylinder/djustable extension type djustable stroke cylinder/djustable retraction type Dual stroke cylinder/double rod Dual stroke cylinder/single rod With split pins for double clevis pin/ double knuckle joint pin and flat washers Series ction/ Type pplicable bore size ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø CQ2 () Double acting Single acting Single rod ø to ø Double rod Note ) Note ) Single rod/ Spring return ø to ø Single rod/ Spring extend CQ2 (arge ore ) Double acting Single rod Double rod ø to ø Note 2) Note 2) CQ2 (ong Stroke) Double acting Single rod ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø Note 2) CQ2K ( Rod) Double acting Single rod Note 4) Note 1) Note 4) Note 4) Double rod Note 4) CQP2 (xial Piping) Double acting Single acting Single rod Single rod/ Spring return CQ2S (nti-lateral oad) Double acting Single rod CQ2 (With nd ock) Double acting Note ) Note ) Single rod/ Spring extend Single rod Note 1) Note 2) Note 2) Note 4) Note ) Note ) Note 4) Note 4) Note 4) Note 3) Note ) Note ) Note 3) Note 3) Note ) Note ) arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock C2 C3 C Double clevis pin/double knuckle joint pin material: Stainless steel 34 With coil scraper With boss on rod end Special port location Full length dimension is the same as Series CQ1. dimension from rod cover is the same as Series CQ1. Special rod end for double rod cylinder Fluororubber seals Full length dimension is the same as Series CQ1W. ong stroke of adjustable extension stroke cylinder (-C) ong stroke of adjustable retraction stroke cylinder (-C) Intermediate stroke of double rod cylinder ong stroke of dual stroke single rod cylinder Cylinder tube: With concave boss on head end Note 1) ø with auto switch: With rubber bumper () Note 2) With rubber bumper () Note 3) ø to ø: (), for ø to ø only (up to ø for single acting type) ø to ø ø to ø ø to ø2 ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø ø to ø Note 4) ø to ø: (), for ø to ø only Note ) ø: ( ) Note ) ø to ø: (), for ø to ø only Note ) Note ) Note ) Note ) Note ) Note ) ø to ø2: (), for ø to ø only Note ) Rod end lock: ( ), for head end lock only Note ) Head end lock: ( ), for rod end lock only Note ) Note ) Note ) With boss on rod end () Note ) ø1 to ø: (), for ø to ø only Note ) The body shape is the same as the existing product. Water Resistant With uto Switch uto Switch ade to Order Front matter 2 Front matter 3

7 Compact Cylinder: Double cting, Single Rod Series CQ2 ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø How to Order Without auto switch ø to ø2 CQ2 3 D Without auto switch ø to ø CQ2 3 D Z With auto switch CDQ2 3 D Z W With auto switch (uilt-in magnet) Through-hole () oth ends tapped Foot mm mm mm 2 2 mm mm mm mm mm mm mm F G D ounting Rod flange Head flange Double clevis ounting brackets are shipped together, (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to ounting olt for C(D)Q2 on pages and. Nil H Type Pneumatic ir-hydro Note 1) Note 1) s available for airhydro type are ø to ø. Port thread type Nil thread ø to ø2 Rc TN TF NPT G ø to ø F uilt-in one-touch fittings Note 2 ) Note 2) s available with one-touch fittings are ø to ø. esides, it is not possible to use for air-hydro type. Note 3) TF is not available for air-hydro type. For cylinders without auto switch, threads are compatible only for ø- mm stroke. Cylinder stroke Refer to the next page and page 3 for standard strokes and intermediate strokes. uto switch mounting groove Z ction D Double acting ø to ø2 ø to ø uto switch Nil Without auto switch Refer to the below table for applicable auto switches. 2 surfaces 4 surfaces Note ) The made-to-order, heat resistant auto switch - is not applicable. ade to Order Refer to the next page for details. ody option Nil F C Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. (Rod end female thread) With boss on head end With rubber bumper Note 4) Combination of body options ( C, FC, F, FC ) is available. Note 4) ir-hydro type with rubber bumper is not available. uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2-2DZ Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. pplicable uto Switches/ Refer to the individual catalog (S-1) for the D-P3DW type. Type Special function lectrical entry Indicator light Wiring (Output) oad voltage 3-wire (NPN) 3-wire (PNP) 2-wire V, V V NV PV V N P 3-wire (NPN) V, NWV NW Diagnostic indication 3-wire (PNP) V PWV PW (2-color indication) Grommet Yes 24 V 2-wire V WV W 3-wire (NPN) V, NV N Water resistant 3-wire (PNP) V PV P (2-color indication) 2-wire V V agnetic field resistant (2-color indication) 2-wire (Non-polar) P3DW Grommet 3-wire (NPN equivalent) V V Yes V V 3V 3 2-wire 24 V No V, V V or less V Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. If water resistance is needed, we recommend water resistant cylinders be used. (Page ) ead wire length symbols:. m Nil (xample) NW Solid state auto switch Reed auto switch 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ DC C uto switch model Perpendicular There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No In-line ead wire length (m). (Nil) 1 () 3 () None (Z) (N) Pre-wired connector Solid state auto switches marked with are produced upon receipt of order. The D-P3DW type is available from ø to ø only. pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC

8 Compact Cylinder: Double cting, Single Rod Series CQ2 JIS Symbol Double acting, Single rod Symbol With boss on head end ade to Order (For details, refer to pages 1 to.) Symbol Specifications - Special rod end shape - Heat resistant cylinder ( to 1 C) w/o auto switch only - Cold resistant cylinder ( to C) w/o auto switch only - ow-speed cylinder ( to mm/s) - Intermediate stroke (xclusive body type) - Intermediate stroke (Spacer-installed type) - ong stroke (ir-hydro type only) - ow-speed cylinder ( to mm/s) - Cylinder with heat resistant auto switch ø to ø only -C4 With heavy-duty scraper, ø to ø only Piston rod/retaining ring/rod end nut -C material: Stainless steel -C djustable stroke cylinder/djustable extension type -C djustable stroke cylinder/djustable retraction type -C Dual stroke cylinder/double rod -C Dual stroke cylinder/single rod With split pins for double clevis pin/ -C2 double knuckle joint pin and flat washers Double clevis pin/double knuckle joint pin -C2 material: Stainless steel 34 -C3 With coil scraper, ø to ø only -C3 With boss on rod end -4 Special port location, with auto switch ø to ø2 only -2 Full length dimension is the same as Series CQ1, xcept ø, ø2. -3 dimension from rod cover is the same as Series CQ1, ø, ø only. -21 Fluororubber seals -2 ong stroke of adjustable extension stroke cylinder (-C) -2 ong stroke of adjustable retraction stroke cylinder (-C) - ong stroke of dual stroke single rod cylinder -1 Cylinder tube: With concave boss on head end Note) -: The body shape is the same as the existing product. Refer to pages to 1 for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Specifications Pneumatic type 2 Double acting, Single rod ir 1. Pa 1. Pa ction Fluid Proof pressure aximum operating pressure inimum operating pressure mbient and fluid temperature ubrication Piston speed With auto switch: to C (No freezing) Not required (Non-lube) to mm/s llowable kinetic energy (J) With rubber bumper Stroke length tolerance +1. mm Note) Note) Stroke length tolerance does not include the amount of bumper change. ir-hydro type 2 ction Fluid Proof pressure aximum operating pressure inimum operating pressure mbient and fluid temperature Piston speed Cushion Pneumatic type,, 2, to stroke,, 1,, 2, 3,, 1,, 2, 3, 3,, 4,,, 1,, 2, 3, 3,, 4,,,, 1,, 2, 3, 3,, 4,,, For long strokes exceeding the standard stroke range, refer to page. For intermediate strokes, refer to page 3. ir-hydro type, 2,,,,. Pa. Pa Without auto switch: to C (No freezing) Double acting, Single rod Turbine oil Note) 1. Pa 1. Pa.1 Pa.1 Pa to C to mm/s None +1. mm Stroke length tolerance Note) Refer to Handling Precautions for SC Products (-3-3) for ctuator Precautions (). Strokes ounting rackets/part No. 2 Without switch With switch Without switch With switch Without switch With switch Without switch With switch stroke,, 1,, 2, 3, 3,, 4,,, 1,, 2, 3, 3,, 4,,,, 1,, 2, 3, 3,, 4,,, odel CQ2-D CQ2-DZ CQ2-D CQ2-DZ CQ2-D CQ2-DZ CQ2-D CQ2-DZ CQ2-DZ CQ2-DZ CQ2-DZ CQ2-DZ CQ2-DZ CQ2-DZ Note 1) Foot CQ- CQ-Z CQ- CQ-Z CQ- CQ-Z CQ-2 CQ-Z2 CQ- CQ- CQ- CQ- CQ- CQ- Flange CQ-F CQ-F CQ-F CQ-F2 CQ-F CQ-F CQ-F CQ-F CQ-F CQ-F CQ-D CQ-D CQ-D CQ-D2 CQ-D CQ-D CQ-D CQ-D CQ-D CQ-D Double clevis Note 1) When ordering a foot bracket, the required quantity will be different depending on the bore size. ø to ø2: Without switch: Order 2 pieces per cylinder. With switch: Order 1 piece per cylinder. (Part number for a set of 2 foot brackets) ø to ø: Order 2 pieces per cylinder. Note 2) Parts belonging to each bracket are as follows. Foot or Flange: ody mounting bolts Double clevis: Clevis pin, Type C retaining rings for axis, ody mounting bolts 2 arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

9 Series CQ2 anufacture of Intermediate Strokes (xcept air-hydro type) 1. Spacer-installed type 1: model number Intermediate stroke with : vailable in 1 mm intervals spacer is installed on tubes with a stroke longer than the specified stroke ( ). : stroke Stroke Stroke Type range , 1 to 2 Spacerinstalled, 2 1 to 4, 1 to type 1 to 1 to Ordering example (when ordering ø- mm stroke (with through-hole (standard), without switch) Type Part no. Order no. 1. Spacer-installed type 1 model number CQ2-DZ (uses mm stroke tube) CQ2-DZ with 1 mm width spacer inside The dimension is mm. 2. Spacer-installed type 2: Suffix - Intermediate stroke with : vailable in 1 mm intervals spacer is installed on tubes with a stroke longer than the specified stroke ( ). : stroke : Stroke in stock Stroke Stroke Type range * *, 1 to 4 Spacer-installed to 1 to 4 type 2 Note) Specify a spacer-installed type 1 with standard Ordering example (when ordering ø- mm stroke (with through-hole (standard), without switch) model number for ordering an intermediate Type 2. Spacer-installed type 2 stroke with a * mark. Refer to page for Part no. Suffix - to the end of model number. details. Order no. CQ2-DZ- (uses mm stroke tube) CQ2-DZ- with 3 mm width spacer inside The dimension is 3 mm. 3. xclusive body type: Suffix - vailable in 1 mm intervals xclusive body can be manufactured for specified stroke upon request.,, 2, to Stroke range to 2 to 4 to to Type xclusive body Note) In the case of exclusive body type with ø to ø (-) with the stroke length exceeding mm, reference values of the longitudinal dimension (/ dimension) will be the same as those with auto switch. Refer to page 1 for details. Ordering example (when ordering ø- mm stroke (with through-hole (standard), without switch) Type Part no. Order no. 3. xclusive body type Suffix - to the end of model number. CQ2-DZ- (uses mm stroke tube) akes mm stroke tube. The dimension is mm. For,,,,,,, and stroke, exclusive bodies are kept in inventory, enabling shorter delivery times. Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. Caution ounting The CQ2 series compact cylinders are designed to create compact mechanical equipment and promote space saving. Thus, if it is used in the same manner as conventional cylinders such as tie-rod cylinders, it may degrade the performance. Pay sufficient attention to the operating conditions when using. 3 Caution 1. llowable lateral load ateral load that can apply to the piston rod end is limited. If a cylinder is used with a lateral load over the limit, it may cause air leakage due to abnormal friction of seals, galling of cylinder tubes and pistons, or abnormal friction of the bearing part. The lateral load applied to the piston rod must be within the allowable range indicated in this catalog. When the load exceeds the limit, use a double rod cylinder, install a guide, or change the bore size to suit the load in order to make the load within the allowable range. s a standard product, an anti-lateral load type cylinder that is resistant to approx. 2 times more than the conventional compact CQ2 series is also available (page ). 2. Connection with a work piece When a work piece is mounted on the piston rod end, connect them aligning the center of piston rod and a work piece. If they are offcenter, lateral load is generated and phenomena mentioned in (1) may occur. In order not to apply the off-center load, use of a floating joint or simple joint is recommended. ounting 3. Simultaneous use of multiple cylinders It is difficult to control the speed of pneumatic cylinders. The following conditions cause speed change: change in supply pressure, load, temperature and lubrication, performance difference of each cylinder, deterioration of each part over time, etc. speed controller can be used to control the speed of multiple cylinders simultaneously for a short period of time, but depending on conditions, it may not work as desired. If multiple cylinders cannot operate simultaneously, unreasonable force is applied to the piston rod because cylinder positions may not be the same. This may cause abnormal friction of seals and bearings, and galling of cylinder tubes and pistons. Do not use an application to operate several cylinders simultaneously by adjusting cylinder speed. If this is inevitable, use a high rigid guide against load, so that the cylinder is not damaged even when the each cylinder output is slightly different.

10 Compact Cylinder: Double cting, Single Rod Series CQ2 llowable Kinetic nergy oad ass and Piston Speed / 2 llowable kinetic energy: a With rubber bumper/ llowable kinetic energy: b Kinetic energy (J) = (m1+m2) V 2 2 m1: ass of cylinder movable parts kg m2: oad mass kg V: Piston speed m/s ass of Cylinder ovable Parts/Without uilt-in agnet ore size Cylinder stroke (J) (g) ass of Cylinder ovable Parts/With uilt-in agnet (g) ore size Cylinder stroke dditional ass of Cylinder ovable Parts (g) 2 Rod end ale thread male thread Nut With rubber bumper Calculation: (xample) CDQ2-DCZ asic mass: CDQ2-DZ 1 g dditional mass: 43 g With rubber bumper 3 g 1 g llowable ateral oad at Rod nd Without uto Switch llowable lateral load at rod end W (N) llowable lateral load at rod end W (N) 3 Cylinder stroke If an allowable lateral load at rod end is exceeding the value in the graph, we recommend anti-lateral load type cylinder be used. 2 W ø ø ø ø ø. 4. ø ø2 ø ø 1. ø. With uto Switch 3 Cylinder stroke ø ø ø ø ø. 4. ø2 ø ø ø 1. ø Theoretical Output Operating direction IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT (ounting orientation: Horizontal) Operating pressure (Pa) (N) 4 arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

11 Series CQ2 Weight Weight (g) Cylinder stroke ounting olt for CQ2/Without uto Switch ounting method: ounting bolt for through-hole mounting of the CQ2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x2 4 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated dditional Weight (g) 2 oth ends tapped Rod end ale thread male thread Nut With boss on head end With rubber bumper uilt-in one-touch fittings Foot (Including mounting bolts) Rod flange (Including mounting bolts) Head flange (Including mounting bolts) Double clevis (Including pin, retaining rings, bolts) Calculation: (xample) CQ2D-DCZ asic weight: CQ2-DZ dditional weight: oth ends tapped With rubber bumper Double clevis ounting bolt g g 43 g 3 g g 31 g Cylinder model CQ2-D -D -1D -D -2D -3D CQ2-D -D -1D -D -2D -3D CQ2-D -D -1D -D -2D -3D -3D -D -4D -D CQ-D -D -1D -D -2D -3D -3D -D -4D -D CQ2-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ- -DZ- -DZ- -DZ- -DZ -DZ- -DZ- -DZ- -DZ- -DZ C... D ounting bolt part no. Cylinder model C D ounting bolt part no. Cylinder model C D ounting bolt part no. CQ-3 x 2 x 3 x 3 x x 4 x CQ-3 x 2 x 3 x 3 CQ2-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ 3 4 CQ- x 3 x x 4 x x x x x x CQ2-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ CQ- x x x x x x x x x x -DZ x -DZ- 1 1 x 1. x 4 -DZ- x -DZ- x x CQ- x 2 x 3 x 3 x x 4 x x x x x CQ- x 3 x 3 x x 4 x x x -DZ- -DZ- -DZ- -DZ -DZ- -DZ- -DZ- -DZ- -DZ CQ2-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ x x x 1 x x x x x x 1 CQ- x 4 x x x x x x x x -DZ- -DZ- -DZ -DZ- -DZ- -DZ- -DZ- -DZ CQ2-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ x x x x x 1 x x 1 x 1 CQ- x x x x x x x x x x x x x CQ- x 3 x 3 x x 4 x x x x x x x x x x x 1 x x x x x -DZ- -DZ- -DZ- -DZ- -DZ -DZ- -DZ- -DZ- -DZ- -DZ CQ2-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ- -DZ- -DZ- -DZ x x x 1 x x x x x x 1 x CQ- x x x x x x x x x x x 1 x x -DZ- -DZ- -DZ- -DZ -DZ- -DZ- -DZ- -DZ- -DZ x x x x 1 x x 1 x 1 x x -DZ x -DZ- x -DZ- x -DZ- 1 x 1 -DZ- x -DZ 1 x 1

12 Compact Cylinder: Double cting, Single Rod Series CQ2 Construction arge ore With rubber bumper With boss on head end ong Stroke Rod uilt-in one-touch fittings xial Piping Component Parts No Description Cylinder tube Piston Piston rod Collar Retaining ring ushing Rod end nut umper 2 aterial luminum alloy luminum alloy Stainless steel Carbon steel luminum alloy luminum alloy casted Carbon tool steel earing alloy Carbon steel Urethane CQ2-PS CQ2-PS CQ2-PS CQ-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø, nodized ø to ø, Chromated, Painted Phosphate coated For ø or more only Nickel plated Replacement Parts/Seal Kit (Pneumatic type) Kits include items!2,!3,!4 from the table. Seal kit includes!2,!3,!4. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) No. umper Centering location ring One-touch fitting Piston seal Rod seal Gasket 2 Description aterial Urethane luminum alloy NR NR NR CQ2H-PS CQ2H2-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS Note ø to ø, Hard anodized ø to ø Replacement Parts/Seal Kit (ir-hydro type) Kit no. Contents Kit no. Contents Kits include items!2,!3,!4 from the table. Seal kit includes!2,!3,!4. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

13 Series CQ2 Clean Series CQ2 Stroke D()Z Clean series Relief type Vacuum type ø, ø, ø, ø2, ø ø, ø, ø, ø, ø pplicable for using inside the clean room graded Class by making an actuator s rod section a double seal construction and discharging by relief port directly to the outside of clean room. Specifications ction Proof pressure aximum operating pressure Cushion Piston speed ounting Note) ø with auto switch: With rubber bumper () 2 Double acting, Single rod 1. Pa 1. Pa None Note) 3 to mm/s 3 to 3 mm/s Through-hole For details, refer to the separate catalog (CT.2-23), Pneumatics quipment for Clean Room. Construction -CQ2 series (Double seal) Relief port -CQ2 series (Single seal, Vacuum suction) Vacuum port (Vacuum suction) Rod seal ushing Rod seal ushing relief port is provided in the area between the double rod seals to discharge the exhaust air outside of the clean room. Thus, the amount of dust generated has been reduced to 1/ of that of an ordinary cylinder. Structurally identical to the - series, the outer rod seal has been removed to evacuate through the vacuum port. This draws out any external air from the clearance between the rod and the cover to practically eliminate the generation of external dust. This should be used in an application that requires an even higher level of cleanliness than the - series.

14 Compact Cylinder: Double cting, Single Rod Series CQ2 Copper and Fluorine-free Series (For CRT anufacturing Process) CQ2 Stroke Copper and fluorine-free series ø, ø, ø, ø2, ø ø, ø, ø, ø, ø D(C)()Z For preventing the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. ong Stroke arge ore Specifications ction Proof pressure aximum operating pressure Cushion Piston speed ounting 2 Double acting, Single rod 1. Pa 1. Pa None/Rubber bumper to mm/s Through-hole/oth ends tapped Rod xial Piping Water Resistant CDQ2 ounting R Stroke D Option Z -C With auto switch (uilt-in magnet) Water resistant cylinder R NR seals (Nitrile rubber) V FK seals (Fluororubber) Ideal for use under the atmosphere having coolant for machine tools, etc. Compatible for the environment, where waterdrops are splashed around the food processing machinery and the car washers, etc. Water resistant 2-color indication solid state auto switch ade to Order Nil Suffix Piston rod/retaining ring/rod end nut material: Stainless steel Piston rod/rod end nut/cover holding bolt material: Stainless steel Note) -C: ø to ø only Refer to pages to for details. nti-lateral oad With nd ock Water Resistant With uto Switch Specifications ction Cushion ade to Order 2 Double acting, Single rod None Piston rod/retaining ring/rod end nut material: Stainless steel (-C) The specifications other than above are the same as those of the standard. Some dimensions may vary from those of the standard. Refer to page for details. uto Switch ade to Order

15 : Double cting, Single Rod Series CDQ2 With uto Switch Refer to the below pages for further information on auto switches. uto switch proper mounting position and its mounting height inimum stroke for auto switch mounting P. to 1 Operating range uto switch mounting brackets/part no. Weight Weight (g) Cylinder stroke dditional Weight (g) 2 oth ends tapped Rod end ale thread male thread Nut With boss on head end With rubber bumper uilt-in one-touch fittings Foot (Including mounting bolts) Rod flange (Including mounting bolts) Head flange (Including mounting bolts) Double clevis (Including pin, retaining rings, bolts) Calculation: (xample) CDQ2D-DCZ asic weight: CDQ2-DZ dditional weight: oth ends tapped With rubber bumper Double clevis 241 g g 43 g 3 g g 43 g dd each weight of auto switches when auto switches are mounted. Construction Component Parts No Description Cylinder tube Piston Piston rod 4 Collar Retaining ring ushing agnet Piston seal Rod seal Gasket aterial luminum alloy luminum alloy Stainless steel Carbon steel luminum alloy luminum alloy casted Carbon tool steel earing alloy NR NR NR Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø, nodized ø to ø, Chromated, Painted Phosphate coated For ø or more only Replacement Parts/Seal Kit (Pneumatic type) 2 Kit no. CQ2-PS CQ2-PS CQ2-PS CQ-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS Contents Kits include items i, o,! from the table. Seal kit includes i, o,!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) Replacement Parts/Seal Kit (ir-hydro type) 2 Kit no. CQ2H-PS CQ2H2-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS Contents Kits include items i, o,! from the table. Seal kit includes i, o,!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g)

16 Compact Cylinder: Double cting, Single Rod Series CQ2 ounting olt for CDQ2/With uto Switch ounting method: ounting bolt for through-hole mounting of the CDQ2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x3 2 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt Cylinder model C D CDQ2-DZ -DZ -1DZ -DZ. -2DZ -3DZ CDQ2-DZ -DZ -1DZ -DZ -2DZ -3DZ CDQ2-DZ -DZ -1DZ -DZ -2DZ -3DZ. -3DZ -DZ -4DZ -DZ CDQ-DZ -DZ -1DZ -DZ -2DZ -3DZ. -3DZ -DZ -4DZ -DZ CDQ2-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ- -DZ- -DZ- -DZ- -DZ -DZ- -DZ- -DZ- -DZ- -DZ ounting bolt part no. Cylinder model C D ounting bolt part no. Cylinder model C D ounting bolt part no. CDQ2-DZ CQ- x -1DZ x -DZ x -2DZ x -3DZ x -3DZ x -DZ x -4DZ x -DZ x. -DZ- 1 1 x 1 -DZ- x -DZ- x -DZ- x -DZ x -DZ- x -DZ- 1 x 1 -DZ- x -DZ- 1 x 1 -DZ 1 x 1 CDQ2-DZ CQ- x -1DZ x -DZ x -2DZ x -3DZ x -3DZ x -DZ x -4DZ 1 x 1 -DZ x -DZ- 1. x. -DZ- x -DZ- x -DZ- x -DZ 1 x 1 -DZ- x -DZ- 1 x 1 -DZ- 1 x 1 -DZ- x -DZ x CQ-3 x 3 x x 4 x x x CQ-3 x x 4 x x x x CQ- x x 4 x x x x x x x x CQ- x x 4 x x x x x x x x CQ- x x 4 x x x x x x x x x x x x x 1 x x x x x CDQ2-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ- -DZ- -DZ- -DZ- -DZ -DZ- -DZ- -DZ- -DZ- -DZ CDQ2-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ- -DZ- -DZ- -DZ- -DZ -DZ- -DZ- -DZ- -DZ- -DZ CDQ2-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ- -DZ- -DZ- -DZ- -DZ -DZ- -DZ- -DZ- -DZ- -DZ CQ- x 4 x x x x x x x x x x x x x 1 x x x x x x 1 CQ- x x x x x x x x x x x x 1 x x x x x x 1 x CQ- x x x x x x x x x x x 1 x x x x x x 1 x x 1 arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

17 Series CQ2 Dimensions ø to ø2/without uto Switch (Through-hole): CQ2 oth ends tapped: CQ2 O1 thread R R oth nds Tapped 2 O1 4 x. 4 x. x 1. x 1. R H thread effective depth C 4 x øn through x øo counterbore Q F øi 2 x x. (Port size) Z ød K + Stroke + Stroke With boss on head end G øth With oss on Head nd 2 G Th Note 1) With boss on rod end: Option (Suffix -C3 to the end of model number.) Rod nd ale Thread C1 1 H x. x 1. x 1.2 x Width across flat 1 H1 C1 1 2 Stroke range to 3 to 3 to to C D F... H 3 x. 4 x. x. x 1. Note 2) The external dimensions with rubber bumper are same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page 1. Note 3) For calculation on the longitudinal dimension of intermediate strokes, refer to page 3. I K N O. depth 3.. depth 3. depth depth Q. Z

18 Compact Cylinder: Double cting, Single Rod Series CQ2 Foot: CQ2 Z H Y 4 x ød Y T + Stroke Y + Stroke Special cap bolt G S + Stroke Foot 2 Stroke range to 3 to 3 to to 1 D G H S T Y Z Foot bracket material: Carbon steel Surface treatment: Nickel plated Y arge ore Rod flange: CQ2F F FZ FV 2 x øfd 1 FT + Stroke + Stroke Rod Flange 2 Stroke range to 3 to 3 to to FD FT FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated ong Stroke Rod xial Piping Head flange: CQ2G + Stroke FT + Stroke 1 F FZ FV 2 x øfd Head Flange 2 Stroke range to 3 to 3 to to Flange bracket material: Carbon steel Surface treatment: Nickel plated The dimensions except, and 1 are the same as those of the rod flange. nti-lateral oad With nd ock 1 Water Resistant Double clevis: CQ2D CT CU + Stroke CW C + Stroke + Stroke 4 x N Cap bolt øcd hole H xis d RR øc C CZ.1.3 Double Clevis 2 Stroke range to 3 to 3 to to C CD C CT CU CW C CZ N 4 x. 4 x. x 1. x 1. Double clevis bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. RR With uto Switch uto Switch 1 ade to Order

19 Series CQ2 Dimensions ø to ø2/with uto Switch (Through-hole): CDQ2 oth ends tapped: CDQ2 O1 thread R R oth nds Tapped 2 O1 4 x. 4 x. x 1. x 1. R H thread effective depth C uto switch inimum lead wire bending radius S U ød V K 2 x øn through 4 x øo counterbore Q + Stroke + Stroke F 2 x x. (Port size) H thread effective depth C U ø to ø2 With boss on head end øth With oss on Head nd G Th Note 1) With boss on rod end: Option (Suffix -C3 to the end of model number.) S V K ø 2 x øn through 4 x øo counterbore G Rod nd ale Thread C1 1 H x. x 1. x 1.2 x Width across flat 1 H1 C1 1 For auto switch proper mounting position and its mounting height, refer to pages to 1. 2 Stroke range to 3 to 3 to to C D F.... H 3 x. 4 x. x. x 1. Note 2) The external dimensions with rubber bumper are same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page 1. Note 3) For calculation on the longitudinal dimension of intermediate strokes, refer to page 3. K N O. depth 3.. depth 3. depth depth Q. S U V 2 2 3

20 Compact Cylinder: Double cting, Single Rod Series CQ2 Foot: CDQ2 Z H Y 4 x ød + Stroke Y Y T + Stroke Special cap bolt G S + Stroke Foot 2 Stroke range to 3 to 3 to to 1 D G H S T Y Z Foot bracket material: Carbon steel Surface treatment: Nickel plated Y arge ore Rod flange: CDQ2F FV F FZ 2 x øfd 1 FT + Stroke + Stroke Rod Flange 2 Stroke range to 3 to 3 to to FD FT FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated ong Stroke Rod xial Piping Head flange: CDQ2G + Stroke + Stroke 1 FT 2 x øfd F FZ FV Head Flange 2 Stroke range to 3 to 3 to to Flange bracket material: Carbon steel Surface treatment: Nickel plated The dimensions except, and 1 are the same as those of the rod flange. nti-lateral oad With nd ock Water Resistant 1 Double clevis: CDQ2D CT CU + Stroke CW RR C + Stroke + Stroke 1 2 x N Cap bolt øcd hole H xis d øc C CZ Double Clevis Stroke range 2 to 3 to 3 to to 1.. C CD C CT CU CW C CZ N 4 x. 4 x. x 1. x 1. For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. RR Double clevis bracket material: Carbon steel Surface treatment: Nickel plated With uto Switch uto Switch ade to Order

21 Z Series CQ2 Dimensions ø to ø/with uto Switch (In the case of without auto switches, the,, F, P and Q dimensions will be only changed. Refer to the dimension table.) oth ends tapped: CQ2/CDQ2 (Through-hole): CQ2/CDQ2 H thread effective depth C O1 thread inimum lead wire bending radius 4 x øn through x øo counterbore Q 2 x P (Rc, NPT, G) (Port size) R R uto switch F oth nds Tapped O1 x 1. x 1. x 1.2 R ød K W J With boss on head end + Stroke + Stroke øth 2 With oss on Head nd Th Note 1) With boss on rod end: Option (Suffix -C3 to the end of model number.) Width across flat 1 H1 C1 1 Rod nd ale Thread 1 C1 H x 1. x 1. 1 x uilt-in one-touch fittings: ø to ø W1 V øz1 2 x P1 (Piping tube O.D.) uilt-in One-touch Fittings Z1 P1 V 3.. W1 2 For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke range Without auto switch With auto switch C F P Q F P Q. x.. to 3 23., 1/ /. 33 to 3. 2., / / to 3. 3., / /4. 1 O depth W 4. Z D H x 1.2 x 1.2 x 1. Note 2) The external dimensions with rubber bumper are same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page 1. Note 3) For calculation on the longitudinal dimension of intermediate strokes, refer to page 3. The spacerinstalled type (, -) and the exclusive body type (-) are available. J 4. K 1 34 N... depth 1 1 depth 1 1

22 Compact Cylinder: Double cting, Single Rod Series CQ2 Foot: CQ2/CDQ2 Z H Y 4 x ød 1 Y + Stroke T + Stroke Y Special cap bolt G S + Stroke Foot Stroke range to, to, to, Z Y Without auto switch S With auto switch S 1 D G H T Y Foot bracket material: Carbon steel Surface treatment: Nickel plated arge ore ong Stroke Rod flange: CQ2F/CDQ2F F FZ FV 4 x øfd FT + Stroke + Stroke Rod Flange Stroke range Without With auto switch auto switch FD FT FV F FZ 1 to 23, 33 to 4. 2.,. 3. to 4. 3., Flange bracket material: Carbon steel Surface treatment: Nickel plated Rod xial Piping + Stroke + Stroke FT 1 Head flange: CQ2G/CDQ2G FV F FZ 4 x øfd Head Flange Stroke range to, to, to, Without auto switch With auto switch Flange bracket material: Carbon steel Surface treatment: Nickel plated The dimensions except, and 1 are the same as those of the rod flange. nti-lateral oad With nd ock Water Resistant 1 Double clevis: CQ2D/CDQ2D 1 CT + Stroke CW C + Stroke + Stroke 4 x N Cap bolt øcd hole H xis d CU RR C CZ Double Clevis Stroke range Without auto switch With auto switch CD CT CU CW C CZ C C 1 to 23, to. 2.., to. 3.., N x 1. x 1. x 1.2 RR Double clevis bracket material: Cast iron Surface treatment: Painted For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. With uto Switch uto Switch ade to Order

23 Series CQ2 Dimensions ø to ø/with uto Switch (In the case of without auto switches, the, dimensions will be only changed. Refer to the dimension table.) (Through-hole): CQ2/CDQ2 oth ends tapped: CQ2/CDQ2 O1 thread R R oth nds Tapped O1 x 1. x 1. x 1. R 1 H thread effective depth C 4 x øn through x øo counterbore 2 x P (Rc, NPT, G) (Port size) inimum lead wire bending radius Q uto switch F Z ød K W J With boss on head end + Stroke + Stroke øth 2 With oss on Head nd Th Note 1) With boss on rod end: Option (Suffix -C3 to the end of model number.) uilt-in one-touch fittings: ø 1 Width across flat 1 2 H1 C Rod nd ale Thread C1 2.. H x x x V øz1 2 x P1 (Piping tube O.D.) uilt-in One-touch Fittings Z1 P1 V. W1 W1 For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke range to, to, to, Without auto switch With auto switch C D 2 3 F.. H x 1. x 2. x 2. Note 2) The external dimensions with rubber bumper are same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page 1. Note 3) For calculation on the longitudinal dimension of intermediate strokes, refer to page 3. J. K N O depth. 1. depth. 1. depth. P 1/4 3/ 3/ Q 1 23 W Z

24 Compact Cylinder: Double cting, Single Rod Series CQ2 Foot: CQ2/CDQ2 + Stroke Head flange: CQ2G/CDQ2G Y Special cap bolt FV Z H 4 x ød Y T + Stroke Y G S + Stroke + Stroke + Stroke FT F FZ 4 x øfd arge ore ong Stroke 1 Rod flange: CQ2F/CDQ2F 1 Double clevis: CQ2D/CDQ2D CT 4 x N Cap bolt Rod FV øcd hole H xis d xial Piping F FZ 4 x øfd FT + Stroke + Stroke CU + Stroke CW C + Stroke + Stroke RR C CZ nti-lateral oad 1 1 With nd ock Foot Stroke range to, to, to, Stroke range to, to, to, Rod Flange Without auto switch S Y Z With auto switch S 1 D G H T Y Foot bracket material: Carbon steel Surface treatment: Nickel plated Stroke range Without auto switch With auto switch FD FT FV F FZ 1 to,, to to 3, Flange bracket material: Carbon steel Surface treatment: Nickel plated Head Flange Stroke range Without auto switch With auto switch The dimensions 1 except, and 1 are to 3 the same as those of 33., the rod flange. to 4., 4. to, Flange bracket material: Carbon steel Surface treatment: Nickel plated Double Clevis Stroke range Without auto switch With auto switch C C CD CT CU CW C to 3 4, 4 4 to , to 1 3 1, Stroke range to, to, to, Double clevis bracket material: Cast iron CZ 1 N RR Surface treatment: Painted x 1. x 1. x 1. 1 For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. 1 Water Resistant With uto Switch uto Switch ade to Order

25 Series CQ2 ccessory rackets I-G, I-Z1 I-G2, I-G3 Single Knuckle Joint I-G4, I-G I-G, I-G Y-G, Y-Z1 Y-G2, Y-G3 Double Knuckle Joint Y-G4, Y-G Y-G, Y-G ø ø ønd hole H xis d ønd hole H xis d aterial: Carbon steel Surface treatment: Nickel plated Part no. pplicable bore size I-G I-Z1 I-G2 I-G3 I-G4 I-G I-G I-G 2,, ø ø2 ø3 ø aterial: Cast iron Surface treatment: Nickel plated x. x 1 x 1.2 x 1.2 x 1. 1 x 1. x 1. 2 x 1. R R U NDH N aterial: Carbon steel aterial: Cast iron Surface treatment: Nickel plated Surface treatment: Nickel plated pplicable pplicable Part no. bore size 1 1 R 1 R1 U1 ND H N NZ pin part no Y-G 21. x IY-G Y-Z x IY-J Y-G x IY-G Y-G x IY-G Y-G4, 42 ø 3 x IY-G Y-G, ø2 1 x IY-G Y-G 1 23 ø3 x IY-G Y-G 24 ø44 2 x IY-G Knuckle pin and retaining rings are included. Knuckle Pin (Common with double clevis pin) Rod nd Nut ø ø l Part no. IY-G IY-J1 IY-G2 IY-G3 IY-G4 IY-G IY-G IY-G pplicable bore size 2,, 1 Dd d Type C retaining rings for axis are included. l m aterial: Carbon steel t pplicable retaining ring Type C for axis Type C for axis Type C for axis Type C for axis Type C for axis Type C for axis Type C1 for axis Type C for axis Part no. NTJ-1 NT-1 NT-2 NT-3 NT-4 NT- NT- NT- pplicable bore size 2,, d x. x 1 x 1.2 x 1.2 x 1. 1 x 1. x 1. 2 x 1. aterial: Carbon steel Surface treatment: Nickel plated H C

26 Compact Cylinder: Double cting, Single Rod Series CQ2 Simple Joint (CQ2): ø to ø Type ounting racket U T1 2 x ød Joint/ounting racket (Type /)/Part No. Y 3 llowable ccentricity ccentricity tolerance ±1 ±1. ±2 acklash. Joint/ounting racket (Type /)/Part No. pplicable mounting bracket Joint Type mounting bracket Type mounting bracket,, YU-3 YU- YU- YU- Y-3 Y- Y- Y- Y-3 Y- Y- Y- ød1 pplicable air cylinder bore size 3 For ø, ø For ø, ø For ø For ø ounting bracket Y Y YU Type mounting bracket Type mounting bracket Joint <Ordering> Joints are not included with type or mounting brackets. Order them separately. (xample) ø Part no. Type mounting bracket Y-3 Joint YU-3 K (Width across flat) H (With locking) ød2 Part no. Y-3 Y- Y- Y- Part no. Y-3 Y- Y- Y- V T2 Part no. Y-3 Y- Y- Y- F T1,,,,,, U 1 T2 Joint V D. V Type ounting racket D 2 3 W F J 1 3 J W aterial: Chromium molybdenum steel (Nickel plated) Joint 2 x ød through 2 x øo counterbore Weight (g) T1.... RS W øo T2 1 aterial: Stainless steel. depth.. depth. 1 depth 21 depth arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch Part no. YU-3 YU- YU- YU- UT U pplicable bore size,, C aterial: Chromium molybdenum steel (Nickel plated) U C d1 d2 H K UT Weight (g) x 1.2 x 1. x 2 x 2. 2 Part no. Y-3 Y- Y- Y-,, T1.... T2 1 V W RS 1 Weight (g) 23 4 uto Switch ade to Order

27 21

28 Without auto switch ø to ø2 Without auto switch ø to ø With auto switch Type With auto switch (uilt-in magnet) Through-hole () oth ends tapped 2 CQ2W CQ2W 24 V V, V V V, V V V, V V 3D 3 D CDQ2W 3 D Z W mm mm mm 2 mm mm mm mm mm mm mm Compact Cylinder: Double cting, Double Rod Series CQ2W ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø F ounting Foot Flange ounting brackets are shipped together, (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to ounting olt for C(D)Q2W on pages 2 and 2. Special function Nil H Nil TN TF F Type Pneumatic ir-hydro Note 1) Note 1) s available for airhydro type are ø to ø. lectrical entry How to Order Port thread type thread ø to ø2 Rc NPT ø to ø G uilt-in one-touch fittings Note 2 ) Note 2) s available with one-touch fittings are ø to ø. esides, it is not possible to use for air-hydro type. Note 3) TF is not available for the air-hydro type. For cylinders without auto switch, threads are compatible only for ø- mm stroke. Wiring (Output) oad voltage NV PV V NWV PWV WV NV PV V Z Cylinder stroke Refer to the next page for standard strokes. uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2W-2DZ N P NW PW W N P P3DW Z ction D Double acting uto switch Nil Without auto switch Refer to the below table for applicable auto switches. uto switch mounting groove ø to ø2 ø to ø ody option 2 surfaces 4 surfaces Number of auto switches Nil S n 2 pcs. 1 pc. n pcs. ade to Order Refer to the next page for details. Nil (Rod end female thread) C With rubber bumper Note 4) Combination of body options ( C ) is available. Note 4) ir-hydro type with rubber bumper is not available. Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. pplicable uto Switches/ Refer to the individual catalog (S-1) for the D-P3DW type. Solid state auto switch Reed auto switch Diagnostic indication (2-color indication) Water resistant (2-color indication) agnetic field resistant (2-color indication) Grommet Indicator light Yes 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 2-wire (Non-polar) uto switch model DC C Perpendicular In-line ead wire length (m) 3-wire V V Yes (NPN equivalent) Grommet V V 3V 3 2-wire 24 V No V, V V or less V Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2.. (Nil) 1 () 3 () None (Z) (N) Pre-wired connector Solid state auto switches marked with are produced upon receipt of order. The D-P3DW type is available from ø to ø only. pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

29 Series CQ2W Specifications JIS Symbol Double acting, Double rod ade to Order (For details, refer to pages 1 to.) Symbol Specifications - Special rod end shape Heat resistant cylinder ( to 1 C) - w/o auto switch only Heat resistant cylinder ( to C) - w/o auto switch only - ow-speed cylinder ( to mm/s) - Intermediate stroke (xclusive body type) - ow-speed cylinder ( to mm/s) -C4 With heavy-duty scraper, ø to ø only Piston rod/retaining ring/rod end nut -C material: Stainless steel -C3 With coil scraper, ø to ø only -C3 With boss on rod end Special port location, with auto switch ø -4 to ø2 only -23 Special rod end for double rod cylinder -21 Fluororubber seals -23 Full length dimension is the same as Series CQ1W. -3 Intermediate stroke of double rod cylinder Refer to pages to 1 for the specifications of cylinders with auto switches. Pneumatic type ction Fluid Proof pressure aximum operating pressure inimum operating pressure mbient and fluid temperature Pneumatic type (Non-lube) stroke,,, 1,, 2, 3, 2,,,,, 1,, 2, 3 3,, 4,,, 1,, 2, 3 3,, 4,,,, 1,, 2, 3 3,, 4,,, 2 ubrication Not required (Non-lube) Piston speed to mm/s llowable kinetic energy (J) With rubber bumper mm Note) Stroke length tolerance Note) Stroke length tolerance does not include the amount of bumper change. ir-hydro type 2 ction Double acting, Double rod Fluid Turbine oil Note) Proof pressure 1. Pa aximum operating pressure 1. Pa inimum operating pressure.1 Pa.1 Pa mbient and fluid temperature to C Piston speed to mm/s Cushion None Stroke length tolerance +1. mm Note) Refer to Handling Precautions for SC Products (-3-3) for ctuator Precautions (). Strokes anufacture of Intermediate Strokes Double acting, Double rod ir 1. Pa 1. Pa. Pa. Pa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) ir-hydro type stroke,, 1,, 2, 3, 2 3,, 4,,, 1,, 2, 3, 3,, 4,,,,, 1,, 2, 3, 3,, 4,,, uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Type Part no. Description Stroke range xample spacer is installed in the standard stroke body. ( mm intervals) Refer to How to Order for the standard model number. (P. ) Strokes in mm intervals are available by installing a spacer in the standard stroke cylinder. Stroke range to to Part no.: CQ2W-DZ CQ2W-DZ with mm width spacer inside The dimension is. mm. spacer is installed in the standard stroke body. (1 mm intervals) Suffix -3 (P. ) to the end of standard model number. (P. ) Strokes in 1 mm intervals are available by installing a spacer in the standard stroke cylinder.,, 2, to Stroke range to 2 to 4 to to Part no.: CQ2W-2DZ-3 CQ2W-DZ with 3 mm width spacer inside The dimension is. mm. xclusive body (-) Suffix - to the end of standard model number. (P. ) Strokes in 1 mm intervals are available by using an exclusive body with the specified stroke.,, 2, to Stroke range to 2 to 4 to to Part no.: CQ2W-DZ- akes mm stroke tube. The dimension is. mm. 23 xcept air-hydro type In the case of spacer type, intermediate strokes with bumper for ø to ø, -3 is not available. In the case of exclusive body type with ø to ø (-) with the stroke length exceeding mm, reference values of the longitudinal dimension will be changed. Calculate length dimensions by deducting from those of or mm stroke models.

30 Compact Cylinder: Double cting, Double Rod Series CQ2W Type ounting rackets/part No. Pneumatic ir-hydro Through-hole () ounting oth ends tapped uilt-in magnet Pipe thread Piping Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. Warning TN TF Note 3) uilt-in one-touch fittings With rubber bumper Through-hole () ounting oth ends tapped uilt-in magnet Piping Pipe thread TN Note 1) ø without auto switch: x. is used for mm stroke piping dimension. Thus, do not enter a symbol for the port thread type. Note 2) The dimension of the ø- mm stroke with built-in one-touch fittings is the same as that of the mm stroke cylinder tube. Note 3) One-touch fittings cannot be replaced. ounting Do not apply reverse torque to the piston rods sticking out from both sides of this cylinder at the same time. The torque makes connection threads inside loosen, which may cause an accident or malfunction. Install or remove loads while the piston rod width across flat is secured. Do not fix the other side of the piston rod width across flat and apply reverse torque. 2 Note 1) x. x. x. x. x. Rc1/ x. x. NPT1/ G1/ Note 2) ø/4 Note 1) x. Rc1/ NPT1/ NPT1/ G1/ ø/4 NPT1/ NPT1/4 G1/4 ø/ NPT1/4 NPT1/4 G1/4 ø/ NPT1/4 NPT3/ G3/ NPT3/ llowable lateral load at rod end (N) llowable lateral load at rod end (N) Rc1/ Rc1/4 Rc1/4 Rc3/ Rc3/ NPT3/ G3/ Rc1/ Rc1/4 Rc1/4 Rc3/ Rc3/ NPT3/ With uto Switch Foot Note 4) 2 Without switch With switch Without switch With switch Without switch With switch Without switch With switch ø ø ø2 ø Cylinder stroke ø ø odel CQ2-D CQ2-DZ CQ2-D CQ2-DZ CQ2-D CQ2-DZ CQ2-D CQ2-DZ CQ2-DZ CQ2-DZ CQ2-DZ CQ2-DZ CQ2-DZ CQ2-DZ ø2 ø 1. Cylinder stroke CQ- CQ-Z CQ- CQ-Z CQ- CQ-Z CQ-2 CQ-Z2 CQ- CQ- CQ- CQ- CQ- CQ- ø ø ø ø ø ø ø ø ø ø ø ø Flange CQ-F CQ-F CQ-F CQ-F2 CQ-F CQ-F CQ-F CQ-F CQ-F CQ-F Note 4) When ordering a foot bracket, the required quantity will be different depending on the bore size. ø to ø2: Without switch: Order 2 pieces per cylinder. With switch: Order 1 piece per cylinder. (Part number for a set of 2 foot brackets) ø to ø: Order 2 pieces per cylinder. Note ) Parts belonging to each bracket are as follows. Foot or Flange: ody mounting bolts llowable ateral oad at Rod nd Without uto Switch 24 arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

31 Series CQ2W Theoretical Output Operating pressure (Pa) ounting olt for CQ2W/Without uto Switch ounting method: ounting bolt for through-hole mounting of the CQ2W is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x3 4 pcs. (N) Weight Weight 2 (g) Cylinder stroke dditional Weight (g) 2 oth ends tapped Rod end ale thread male thread Nut With rubber bumper uilt-in one-touch fittings Foot (Including mounting bolts) Flange (Including mounting bolts) Calculation: (xample) CQ2WF-DCZ asic weight: CQ2W-DZ 2 g dditional weight: oth ends tapped g g With rubber bumper 3 g Flange 1 g 2 g aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt Cylinder model CQ2W-D -D -1D -D -2D -3D CQ2W-D -D -1D -D -2D -3D CQ2W-D -D -1D -D -2D -3D -3D -D -4D -D CQ2W2-D -D -1D -D -2D -3D -3D -D -4D -D 2 C.3. D ounting bolt part no. CQ-3 x 3 x x 4 x x x CQ-3 x 3 x x 4 x x x CQ- x 3 x 3 x x 4 x x x x x x CQ- x 3 x x 4 x x x x x x x Cylinder model C CQ2W-DZ -DZ -1DZ -DZ -2DZ -3DZ. -3DZ -DZ -4DZ -DZ -DZ -DZ CQ2W-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ -DZ CQ2W-DZ -1DZ -DZ -2DZ -3DZ -3DZ. -DZ -4DZ -DZ -DZ -DZ D ounting bolt part no. CQ- x 3 x x 4 x x x x x x x x x 1 CQ- x 4 x x x x x x x x x x x 1 CQ- x x x x x x x x x x x 1 Cylinder model C CQ2W-DZ -1DZ -DZ -2DZ -3DZ -3DZ. -DZ -4DZ -DZ -DZ -DZ CQ2W-DZ -1DZ -DZ -2DZ -3DZ -3DZ. -DZ -4DZ -DZ -DZ -DZ CQ2W-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ -DZ D ounting bolt part no. CQ- x x x x x x x x x x x 1 CQ- x x x x x x x x x x x CQ- x x x x x x x x x 1 x x 1

32 Compact Cylinder: Double cting, Double Rod Series CQ2W Construction With rubber bumper arge ore Component Parts No Description Cylinder tube Piston Piston rod Piston rod Collar Retaining ring ushing Rod end nut umper One-touch fitting Rod seal Piston seal Tube gasket Piston gasket aterial luminum alloy luminum alloy Stainless steel Carbon steel Stainless steel Carbon steel luminum alloy luminum alloy casted Carbon tool steel earing alloy Carbon steel Urethane NR NR NR NR Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø2 ø to ø, Hard chrome plated ø to ø, nodized ø to ø, Chromated, Painted Phosphate coated For ø or more only Nickel plated ø to ø uilt-in one-touch fittings ong Stroke Rod xial Piping nti-lateral oad Replacement Parts/Seal Kit (Pneumatic type) Kit no. Contents 2 CQ2W-PS CQ2W-PS CQ2W-PS CQ2W2-PS Kits include items CQ2W-PS!1,!2,!3 from CQ2W-PS the table. CQ2W-PS CQ2W-PS CQ2W-PS CQ2W-PS Seal kit includes!1,!2,!3. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) Replacement Parts/Seal Kit (ir-hydro type) Copper and Fluorine-free Series (For CRT anufacturing Process) Kit no. Contents 2 CQ2WH-PS CQ2WH2-PS CQ2WH-PS Kits include items CQ2WH-PS!1,!2,!3 from CQ2WH-PS the table. CQ2WH-PS CQ2WH-PS CQ2WH-PS Seal kit includes!1,!2,!3. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) With nd ock Water Resistant With uto Switch CQ2W Stroke D(C)()(Z) Copper and fluorine-free series ø, ø, ø, ø2, ø ø, ø, ø, ø, ø For preventing the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. Specifications ction Proof pressure ax. operating pressure Rubber bumper Piping Piston speed ounting uto switch 2 Double acting, Double rod 1. Pa 1. Pa None Pipe thread to mm/s Through-hole ountable 2 uto Switch ade to Order

33 : Double cting, Double Rod Series CDQ2W With uto Switch Refer to the below pages for further information on auto switches. uto switch proper mounting position and its mounting height inimum stroke for auto switch mounting P. to 1 Operating range uto switch mounting brackets/part no. Weight Weight 2 (g) Cylinder stroke dditional Weight (g) 2 oth ends tapped Rod end ale thread male thread Nut With rubber bumper uilt-in one-touch fittings Foot (Including mounting bolts) Flange (Including mounting bolts) Calculation: (xample) CDQ2WF-DCZ asic weight: CDQ2W-DZ 3 g dditional weight: oth ends tapped g g With rubber bumper 3 g Rod flange 1 g g dd each weight of auto switches when auto switches are mounted. Construction Component Parts No Description Cylinder tube Piston Piston rod Piston rod Collar Retaining ring ushing agnet Rod seal Piston seal Tube gasket Piston gasket aterial luminum alloy luminum alloy Stainless steel Carbon steel Stainless steel Carbon steel luminum alloy luminum alloy casted Carbon tool steel earing alloy NR NR NR NR Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø2 ø to ø, Hard chrome plated ø to ø, nodized ø to ø, Chromated, Painted Phosphate coated For ø or more only Replacement Parts/Seal Kit (Pneumatic type) Kit no. Contents 2 CQ2W-PS CQ2W-PS CQ2W-PS CQ2W2-PS CQ2W-PS Kits include items o,!,!1 from CQ2W-PS the table. CQ2W-PS CQ2W-PS CQ2W-PS CQ2W-PS Seal kit includes o,!,!1. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) Replacement Parts/Seal Kit (ir-hydro type) Kit no. Contents 2 CQ2WH-PS CQ2WH2-PS CQ2WH-PS CQ2WH-PS Kits include items o,!,!1 from CQ2WH-PS the table. CQ2WH-PS CQ2WH-PS CQ2WH-PS Seal kit includes o,!,!1. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) 2

34 Compact Cylinder: Double cting, Double Rod Series CQ2W ounting olt for CDQ2W/With uto Switch ounting method: ounting bolt for through-hole mounting of the CDQ2W is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x 2 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt Cylinder model CDQ2W-DCZ -DCZ -1DCZ -DCZ -2DCZ -3DCZ CDQ2W-DZ -DZ -1DZ -DZ -2DZ -3DZ CDQ2W-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ CDQ2W2-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ C.1. D ounting bolt part no. Cylinder model C D ounting bolt part no. Cylinder model C D ounting bolt part no. 4 CQ-3 x x 4 x x x CDQ2W-DZ -DZ -1DZ -DZ -2DZ 4 CQ- x 4 x x x x CDQ2W-DZ -1DZ -DZ -2DZ -3DZ CQ- x x x x x x -3DZ x -3DZ. x. 4 CQ-3 x 4-3DZ x -DZ x 4 x x x x x CQ- x 4 x x x x -DZ -4DZ -DZ -DZ -DZ CDQ2W-DZ -DZ -1DZ -DZ -2DZ 1 x x x x x 1 CQ- x x x x x -4DZ -DZ -DZ -DZ CDQ2W-DZ -1DZ -DZ -2DZ -3DZ -3DZ. 1 x x x x 1 CQ- x x x x x x x -3DZ x -DZ x x -3DZ x -4DZ x 4 x x x CQ- x 4 x x x x x x -DZ -4DZ -DZ -DZ -DZ CDQ2W-DZ -1DZ -DZ -2DZ -3DZ 1 x x x x x 1 CQ- x x x x x -DZ -DZ -DZ CDQ2W-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ 1 1 x 1 x x CQ- x x x x x x x 1 x x x -3DZ -DZ -4DZ. x x x -4DZ -DZ -DZ x x x -DZ x -DZ 1 x 1 -DZ x -DZ 1 x 1 ade to Order arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock uto Switch With uto Switch Water Resistant 2

35 Series CQ2W Dimensions ø to ø2/without uto Switch (Through-hole): CQ2W oth ends tapped: CQ2W O1 thread R R oth nds Tapped 2 O1 4 x. 4 x. x 1. x 1. R 2 x H thread effective depth C (lso back cover) 4 x øn through x øo counterbore Q Q 2 x x. (Port size) øi Width across flat K Z ød ød K + Stroke + 2 (Stroke) + Stroke Note 1) The positions of left and right width across flats are not constant. 2 x Width across flat 1 H1 H1 Width across flat 1 C (Stroke) 1 + Stroke C1 Rod nd ale Thread C1 1 H x. x 1. x 1.2 x Stroke range to 3.2 to 3 33 to 3 to C D H 3 x. 4 x. x. x 1. Note 2) The external dimensions with rubber bumper are same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page 1. I K N O. depth 3.. depth 3. depth depth Q. Z 2

36 Compact Cylinder: Double cting, Double Rod Series CQ2W Foot: CQ2W Special cap bolt + Stroke + Stroke Note) The positions of left and right width across flats are not constant. FV H Y arge ore Z 4 x ød Y T Y + 2 (Stroke) G S + Stroke ong Stroke Foot 2 Stroke range to 3 to 3 to to D G (Stroke) H S Stroke T Y Z Y Foot bracket material: Carbon steel Surface treatment: Nickel plated Rod nd ale Thread Rod xial Piping nti-lateral oad Flange: CQ2WF Note) The positions of left and right width across flats are not constant. With nd ock F FZ 2 x øfd 1 FT + Stroke + 2 (Stroke) 2 + Stroke Water Resistant Flange 2 Stroke range to 3 to 3 to to For details about the rod end nut and accessory brackets, refer to page FD (Stroke) 4 + Stroke FT FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated Rod nd ale Thread With uto Switch uto Switch ade to Order

37 Series CQ2W Dimensions ø to ø2/with uto Switch (Through-hole): CDQ2W O1 thread oth ends tapped: CDQ2W R R oth nds Tapped 2 O1 4 x. 4 x. x 1. x 1. R H thread effective depth C uto switch inimum lead wire bending radius Note 1) The positions of left and right width across flats are not constant. Width across flat K S ød ød U 2 x øn through 4 x øo counterbore V K Q Q + Stroke + 2 (Stroke) 2 x x. (Port size) + Stroke ø to ø2 2 x H thread effective depth C Width across flat 1 U S H1 H1 Width across flat 1 V 2 x øn through 4 x øo counterbore C (Stroke) C1 1 + Stroke K ø Rod nd ale Thread C1 1 H x. x 1. x 1.2 x For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke range C D H K 2 to 3 to 3 to to x. 4 x. x. x Note 2) The external dimensions with rubber bumper are same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page N O. depth 3.. depth 3. depth depth Q.. S U V 2 2 3

38 Compact Cylinder: Double cting, Double Rod Series CQ2W Foot: CDQ2W Special cap bolt + Stroke + Stroke Note) The positions of left and right width across flats are not constant. Foot Z Stroke range to 3 to 3 to 2 to Flange: CDQ2WF H Y 4 x ød D G Y H T S + Stroke Y + 2 (Stroke) (Stroke) S G 1 + Stroke T Y Z Y 4... Foot bracket material: Carbon steel Surface treatment: Nickel plated Rod nd ale Thread arge ore ong Stroke Rod xial Piping nti-lateral oad FV 2 x øfd Note) The positions of left and right width across flats are not constant. With nd ock F FZ 1 FT + Stroke + 2 (Stroke) 2 + Stroke Water Resistant Flange 2 Stroke range to 3 to 3 to to For details about the rod end nut and accessory brackets, refer to page FD (Stroke) 4 + Stroke FT.. FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated Rod nd ale Thread With uto Switch uto Switch ade to Order

39 Series CQ2W Dimensions ø to ø/with uto Switch (In the case of without auto switches, the, and P dimensions will be only changed. Refer to the dimension table.) (Through-hole): CQ2W/CDQ2W oth ends tapped: CQ2W/CDQ2W O1 thread R R oth nds Tapped O1 x 1. x 1. x 1.2 R H thread effective depth C 4 x øn through x øo counterbore 2 x P (Port size) Q inimum lead wire bending radius uto switch Q Width across flat K Note 1) The positions of left and right width across flats are not constant. Z ød ød K W J 2 x Width across flat 1 H1 C1 1 + Stroke + 2 (Stroke) uilt-in one-touch fittings: ø to ø + Stroke Width across flat 1 C1 1 + Stroke (Stroke) H1 Rod nd ale Thread Stroke range to, to, to, 1 2 Without auto switch 1 C H With auto switch 1.. x 1. x 1. 1 x V 2 x P1 (Piping tube O.D.) W1 øz1 uilt-in One-touch Fittings Without auto switch V W With auto switch V W Z1 P1 For auto switch proper mounting position and its mounting height, refer to pages to 1. Without auto switch With auto switch P Stroke range to, to, to, / 1/ 1/ P 1/ 1/ 1/4 33 C 1 D H x 1.2 x 1.2 x 1. J 4. K 1 34 N... O depth depth depth Q. W 4. 1 Z 1 1 Note 2) The external dimensions with rubber bumper are same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page 1.

40 Compact Cylinder: Double cting, Double Rod Series CQ2W Foot: CQ2W/CDQ2W + Stroke + Stroke Note) The positions of left and right width across flats are not constant. Y Foot Z H Stroke range to, to, to, 4 x ød Special cap bolt 1 Y T Y + 2 (Stroke) (Stroke) G 1 + Stroke S + Stroke Without auto switch With auto switch S S Foot bracket material: Carbon steel D G H T Y Z Y Surface treatment: Nickel plated Rod nd ale Thread Stroke range to, to, to, Without auto switch With auto switch arge ore ong Stroke Rod xial Piping nti-lateral oad Flange: CQ2WF/CDQ2WF FV Note) The positions of left and right width across flats are not constant. With nd ock Flange F FZ 4 x øfd Stroke range to, to, to, FT + Stroke + 2 (Stroke) (Stroke) Without auto switch With auto switch Stroke Stroke Rod nd ale Thread 2 Stroke range to, to, to, FD FT FV F FZ Without auto switch With auto switch Flange bracket material: Carbon steel Surface treatment: Nickel plated Water Resistant With uto Switch uto Switch ade to Order

41 Series CQ2W Dimensions ø to ø/with uto Switch (In the case of without auto switches, the and dimensions will be only changed. Refer to the dimension table.) (Through-hole): CQ2W/CDQ2W O1 thread oth ends tapped: CQ2W/CDQ2W R R oth nds Tapped O1 x 1. x 1. x 1. R 1 H thread effective depth C 2 x P 4 x øn through (Port size) x øo counterbore Q inimum lead wire bending radius uto switch Q Width across flat K Note 1) The positions of left and right width across flats are not constant. Z ød ød K W J 2 x Width across flat 1 H1 + Stroke + 2 (Stroke) + Stroke Width across flat 1 H1 Rod nd ale Thread Stroke range to, to, to, Without auto switch With auto switch 1 1. C (Stroke) C1 1 + Stroke 1 C1 H1 1 uilt-in one-touch fittings W1 V øz1 2 x P1 (Piping tube O.D.) x x x 1. uilt-in One-touch Fittings Z1 P1 V W1. The dimension of the ø- mm stroke with built-in onetouch fittings is the same as that of the mm stroke cylinder tube For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke range Without auto switch With auto switch to 42, 2 2 to 1 1, to 4.., C D H J K x 1. x 2. x N depth. 1. depth. 1. depth. Note 2) The external dimensions with rubber bumper are same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page 1. O P 1/4 3/ 3/ Q 1. 1 W Z

42 Compact Cylinder: Double cting, Double Rod Series CQ2W Foot: CQ2W/CDQ2W + Stroke + Stroke Note) The positions of left and right width across flats are not constant. Y Foot Z H 4 x ød Special cap bolt Stroke range to, to, to, Y T Y + 2 (Stroke) G D G H T Y Z Y S + Stroke Stroke (Stroke) Without auto switch With auto switch S S Foot bracket material: Carbon steel Surface treatment: Nickel plated Rod nd ale Thread Stroke range to, to, to, Without auto switch With auto switch arge ore ong Stroke Rod xial Piping nti-lateral oad Flange: CQ2WF/CDQ2WF FV Note) The positions of left and right width across flats are not constant. With nd ock Flange F FZ to, to, to, 4 x øfd Stroke range FT + Stroke + 2 (Stroke) (Stroke) Without auto switch With auto switch Stroke 4 + Stroke 2 1 Rod nd ale Thread 4 Stroke range to, to, to, FD FT FV F FZ Without auto switch With auto switch Flange bracket material: Carbon steel Surface treatment: Nickel plated Water Resistant With uto Switch uto Switch ade to Order

43 3

44 Compact Cylinder: Single cting, Single Rod Series CQ2 ø, ø, ø, ø2, ø, ø, ø How to Order Without auto switch ø to ø2 Without auto switch ø to ø With auto switch With auto switch (uilt-in magnet) Through-hole () oth ends tapped Foot mm mm mm 2 2 mm mm mm mm CQ2 CQ2 CDQ2 F G D ounting Rod flange Head flange Double clevis ounting brackets are shipped together, (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to ounting olt for C(D)Q2 on pages 41 and 44. Nil TN TF F uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2-SZ Port thread type thread ø to ø2 Rc NPT ø to ø G uilt-in one-touch fittings Note) Note) s available with one-touch fittings are ø to ø. For cylinders without auto switch, threads are compatible only for ø- mm stroke model. S S S Z Z W Cylinder stroke Refer to the next page for standard strokes. Number of auto switches Nil S n 2 pcs. 1 pc. n pcs. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. uto switch mounting groove Z ø to ø2 ø to ø ody option Nil F 2 surfaces 4 surfaces With boss on head end Combination of body options ( F ) is available. ction S Single acting, Spring return T Single acting, Spring extend ade to Order Refer to the next page for details. arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock pplicable uto Switches/Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) lectrical entry Grommet Grommet Indicator light Yes Yes No Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN equivalent) 2-wire V, V V V, 24 V V V V, V V 24 V oad voltage DC NV PV V NWV PWV WV NV PV V V V 3V V N P NW PW W N P Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW Solid state auto switches marked with are produced upon receipt of order. 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ C V V V, V V or less uto switch model Perpendicular There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2. In-line 3 ead wire length (m). (Nil) 1 () 3 () None (Z) (N) Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC 3 Water Resistant With uto Switch uto Switch ade to Order

45 Series CQ2 Specifications 2 ction Fluid Proof pressure aximum operating pressure inimum operating pressure (Pa) mbient and fluid temperature ubrication Piston speed Single acting, Single rod ir 1. Pa 1. Pa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Not required (Non-lube) to mm/s llowable kinetic energy (J) Stroke length tolerance +1. mm JIS Symbol Single acting, Spring return Single acting, Spring extend Strokes stroke,,, 2,,,, ade to Order (For details, refer to pages 1 to.) anufacture of Intermediate Strokes (xcept single acting, spring return type) Symbol Specifications - Special rod end shape, spring return type only Intermediate stroke (xclusive body type), - Spring return type only Piston rod/retaining ring/rod end nut -C material: Stainless steel With split pins for double clevis pin/ -C2 double knuckle joint pin and flat washers Double clevis pin/double knuckle joint pin -C2 material: Stainless steel 34 -C3 With boss on rod end Special port location, with auto switch ø -4 to ø2 only Type Part no. Description Stroke range xample spacer is installed in the standard stroke body. Refer to How to Order for the standard model number. (P. 3) Strokes in 1 mm intervals are available by installing a spacer in the standard stroke cylinder. to Part no.: CQ2-3T CQ2-T with 2 mm width spacer inside The dimension is 24. mm. Stroke range 1 to 1 to 1-2 Full length dimension is the same as Series CQ1, xcept ø, ø, ø2. Type dimension from rod cover is the same as Series CQ1, ø, ø only. Fluororubber seals Cylinder tube: With concave boss on head end Refer to pages to 1 for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Pneumatic Through-hole () ounting oth ends tapped uilt-in magnet Piping Pipe thread TN TF Note 2) uilt-in one-touch fittings With boss on head end Note 1) ø without auto switch: x. is used for mm stroke piping dimension. Thus, do not enter a symbol for the port thread type. Note 2) One-touch fittings cannot be replaced. x. x. x. 2 Note 1) x. x. Rc1/ Rc1/ NPT1/ G1/ NPT1/ G1/ ø/4 ø/4 Rc1/4 NPT1/4 G1/4 ø/ 3

46 Compact Cylinder: Single cting, Single Rod Series CQ2 Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. Spring Force Single cting, Spring Return (N) Spring reaction force (N) 2 Stroke Second First Single cting, Spring xtend (N) Stroke Spring reaction force (N) Second First Single acting, Spring return Spring state with first mounting load IN When spring is set in cylinder Single acting, Spring extend Spring state with first mounting load OUT When spring is set in cylinder Spring state with second mounting load OUT When spring is compressed with air Spring state with second mounting load IN When spring is compressed with air ounting rackets/part No. Without switch CQ2-D With switch CQ2-DZ Without switch CQ2-D With switch CQ2-DZ Without switch CQ2-D With switch CQ2-DZ Without switch CQ2-D 2 With switch CQ2-DZ CQ2-DZ CQ2-DZ CQ2-DZ Note 1) odel Foot Flange Double clevis CQ- CQ-Z CQ- CQ-Z CQ- CQ-Z CQ-2 CQ-Z2 CQ- CQ- CQ- CQ-F CQ-F CQ-F CQ-F2 CQ-F CQ-F CQ-F CQ-D CQ-D CQ-D CQ-D2 CQ-D CQ-D CQ-D Note 1) When ordering a foot bracket, the required quantity will be different depending on the bore size. ø to ø2: Without switch: Order 2 pieces per cylinder. With switch: Order 1 piece per cylinder. (Part number for a set of 2 foot brackets) ø to ø: Order 2 pieces per cylinder. Note 2) Parts belonging to each bracket are as follows. Foot or Flange: ody mounting bolts Double clevis: Clevis pin, Type C retaining rings for axis, ody mounting bolts Weight Weight ction Spring return Spring extend 2 2 dditional Weight oth ends tapped ale thread Nut With boss on head end uilt-in one-touch fittings Foot (Including mounting bolts) Rod flange (Including mounting bolts) Head flange (Including mounting bolts) Double clevis (Including pin, retaining rings, bolts) Calculation: (xample) CQ2D-SZ asic weight: CQ2-SZ dditional weight: oth ends tapped Double clevis 2 2 (N) Operating pressure (Pa) Cylinder stroke g g 43 g g 34 g Theoretical Output ction Spring return Spring extend (g) (g) arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

47 Series CQ2 ounting olt for CQ2/Without uto Switch ounting method: ounting bolt for through-hole mounting of the CQ2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x2 4 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt ounting bolt Spring Return Cylinder model CQ2-S -S CQ2-S -S CQ2-S -S CQ-S -S CQ2-SZ -SZ CQ2-SZ -SZ CQ2-SZ -SZ C..... D ounting bolt part no. CQ-3 x 2 x 3 CQ-3 x 2 x 3 CQ- x 2 x 3 CQ- x 3 x 3 CQ- x 3 x 3 CQ- x 3 x CQ- x 4 x Spring xtend Cylinder model CQ2-T -T CQ2-T -T CQ2-T -T CQ-T -T CQ2-TZ -TZ CQ2-TZ -TZ CQ2-TZ -TZ C..... D ounting bolt part no. CQ-3 x 2 x 3 CQ-3 x 2 x 3 CQ- x 2 x 3 CQ- x 3 x 3 CQ- x 3 x 3 CQ- x 3 x CQ- x 4 x 41

48 Compact Cylinder: Single cting, Single Rod Series CQ2 Construction Spring return Spring extend Port size x. With boss on head end uilt-in one-touch fittings arge ore ong Stroke Rod Component Parts No Description Cylinder tube Piston Piston rod Collar Retaining ring ushing Return spring ronze element Retaining ring Plug with fixed orifice Rod end nut Centering location ring One-touch fitting aterial luminum alloy luminum alloy Stainless steel Carbon steel luminum alloy luminum alloy casted Carbon tool steel earing alloy Piano wire Sintered metallic C Carbon tool steel lloy steel Carbon steel luminum alloy Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø, nodized ø, Chromated, Painted Phosphate coated ø Zinc chromated Port size Rc1/, 1/4 Port size x. Nickel plated ø to ø, nodized ø to ø On spring extend (Type T), piston and piston rod are integrated (stainless steel). (xcept ø and ø of built-in magnet type) Replacement Parts No. 1 Replacement Parts/Seal Kit 2 Contents How to Order Description Piston seal Rod seal Gasket aterial NR NR NR Single acting/spring return CQ2-S-PS CQ2-T-PS CQ2-S-PS CQ2-T-PS CQ2-S-PS CQ2-T-PS CQ-S-PS CQ-T-PS CQ2-S-PS CQ2-T-PS CQ2-S-PS CQ2-T-PS CQ2-S-PS CQ2-T-PS Kits includes item!4 from the above table. Kits include items!4,!,! from the above table. Seal kit includes!4. Order the seal kit, based on each bore size. Copper and Fluorine-free Series (For CRT anufacturing Process) Note Single acting/spring extend Seal kit includes!4,!,!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch CQ2 Copper and fluorine-free series S Stroke T ()Z ø, ø, ø, ø2, ø ø, ø Specifications ction Proof pressure 2 Single acting, Single rod 1. Pa uto Switch ax. operating pressure 1. Pa For preventing the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. Rubber bumper Piping Piston speed ounting uto switch None Pipe thread to mm/s Through-hole ountable ade to Order 42

49 : Single cting, Single Rod Series CDQ2 With uto Switch Refer to the below pages for further information on auto switches. uto switch proper mounting position and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. P. to 1 Weight Weight ction Spring extend Spring return 2 2 (g) Cylinder stroke dditional Weight oth ends tapped 1 ale thread 1. Nut 1 With boss on head end. uilt-in one-touch fittings Foot (Including mounting bolts) 4 Rod flange (Including mounting bolts) 4 Head flange (Including mounting bolts) 2 Double clevis (Including pin, retaining rings, bolts) 2 Calculation: (xample) CDQ2D-SZ asic weight: CDQ2-SZ 2 g dditional weight: oth ends tapped g 43 g Double clevis g 2 g (g) dd each weight of auto switches when auto switches are mounted. Construction Spring return Spring extend Port size x. Component Parts No Description Cylinder tube Piston Piston rod Collar Retaining ring ushing Return spring ronze element Retaining ring Plug with fixed orifice agnet aterial luminum alloy luminum alloy Stainless steel Carbon steel luminum alloy luminum alloy casted Carbon tool steel earing alloy Piano wire Sintered metallic C Carbon tool steel lloy steel Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø, nodized ø, Chromated, Painted Phosphate coated ø Zinc chromated Port size Rc1/, 1/4 Port size x. On spring extend (Type T), piston with ø or more and piston rod are integrated (stainless steel). 43 No. Description Piston seal Rod seal Gasket aterial NR NR NR Replacement Parts/Seal Kit Note Since the same as those of the standard, single acting, single rod, refer to page 42.

50 Compact Cylinder: Single cting, Single Rod Series CQ2 ounting olt for CDQ2/With uto Switch ounting method: ounting bolt for through-hole mounting of the CDQ2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x3 2 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated Spring return ounting bolt Spring extend ounting bolt arge ore Spring Return Cylinder model CDQ2-SZ -SZ CDQ2-SZ -SZ CDQ2-SZ -SZ CDQ-SZ -SZ CDQ2-SZ -SZ CDQ2-SZ -SZ CDQ2-SZ -SZ C..... D ounting bolt part no. CQ-3 x 3 x CQ-3 x x 4 CQ- x x 4 CQ- x x 4 CQ- x x 4 CQ- x 4 x CQ- x x Spring xtend Cylinder model CDQ2-TZ -TZ CDQ2-TZ -TZ CDQ2-TZ -TZ CDQ-TZ -TZ CDQ2-TZ -TZ CDQ2-TZ -TZ CDQ2-TZ -TZ C D ounting bolt part no. CQ-3 x x 4 CQ-3 x x 4 CQ- x x 4 CQ- x x 4 CQ- x x 4 CQ- x 4 x CQ- x x ade to Order uto Switch ong Stroke With uto Switch Rod xial Piping Water Resistant With nd ock nti-lateral oad 44

51 Series CQ2 Dimensions ø to ø2/ Spring Return Without uto Switch (Through-hole): CQ2 H thread effective depth C 4 x øn through x øo counterbore oth ends tapped: CQ2 O1 thread R R F oth nds Tapped 2 O1 4 x. 4 x. x 1. x 1. R øi x. (Port size) Z ød K With boss on head end G øth With oss on Head nd 2 G Th Note) With boss on rod end: Option (Suffix -C3 to the end of model number.) Width across flat 1 H1 C1 1 Rod nd ale Thread C1 1 H x. x 1. x 1.2 x Stroke For details about the rod end nut and accessory brackets, refer to page 1. 4 C D F... H 3 x. 4 x. x. x 1. I K N O. depth 3.. depth 3. depth depth Z

52 Compact Cylinder: Single cting, Single Rod Series CQ2 Foot: CQ2 Z H Y 4 x ød T Rod flange: CQ2F 1 Y Y S Special cap bolt G Foot 2 2 st T st st Y st Z Y 4... Foot bracket material: Carbon steel Surface treatment: Nickel plated D G H st... S st arge ore ong Stroke F FZ FV 2 x øfd FT Rod Flange 2 st st st st FD FT.. FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated Rod xial Piping Head flange: CQ2G FT 1 F FZ FV 2 x øfd Head Flange 2 st st Flange bracket material: Carbon steel Surface treatment: Nickel plated The dimensions except, and 1 are the same as those of the rod flange. nti-lateral oad Water Resistant With nd ock 1 Double clevis: CQ2D 1 CT C CU CW 4 x N Cap bolt øcd hole H xis d RR øc C CZ.1.3 Double Clevis 2 2 st C. st CZ st st C 24 N CD 4 x. 4 x. x 1. x 1. st RR C st Double clevis bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. CT 4 4 CU CW With uto Switch uto Switch ade to Order

53 U S Series CQ2 Dimensions ø to ø2/spring Return With uto Switch (Through-hole): CDQ2 H thread effective depth C oth ends tapped: CDQ2 R R O1 thread uto switch oth nds Tapped 2 O1 4 x. 4 x. x 1. x 1. inimum lead wire bending radius R ød V K 2 x øn through 4 x øo counterbore x. F (Port size) S U ø to ø2 H thread effective depth C V K ø 2 x øn through 4 x øo counterbore Width across flat 1 H1 C1 With boss on head end G øth With oss on Head nd 2 2 G C1 1 Th Note) With boss on rod end: Option (Suffix -C3 to the end of model number.) Rod nd ale Thread H x. x 1. x 1.2 x For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke C D F H K For details about the rod end nut and accessory brackets, refer to page x. 4 x. x. x N O. depth 3.. depth 3. depth depth S U V 2 2 3

54 FV Compact Cylinder: Single cting, Single Rod Series CQ2 Foot: CDQ2 Z H Y 4 x ød 1 T Y Y S Special cap bolt G Foot 2 2 st T st st Y st Z Y 4... Foot bracket material: Carbon steel Surface treatment: Nickel plated D G H st S st arge ore ong Stroke Rod flange: CDQ2F FV F FZ 2 x øfd FT 1 Rod Flange 2 st st st st FD FT.. FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated Rod xial Piping Head flange: CDQ2G CT 2 x øfd FT Double clevis: CDQ2D F FZ 2 x N Cap bolt øcd hole H xis d 1 øc Head Flange 2 2 st st. 2. st Double Clevis st st Flange bracket material: Carbon steel Surface treatment: Nickel plated st The dimensions except, and 1 are the same as those of the rod flange. C 24 CD st C st. 4. CT 4 4 CU CW 1 1 nti-lateral oad With nd ock Water Resistant With uto Switch CU C CW 1 RR C +.4 CZ C. CZ N 4 x. 4 x. x 1. x 1. For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. RR Double clevis bracket material: Carbon steel Surface treatment: Nickel plated 4 uto Switch ade to Order

55 Series CQ2 Dimensions ø to ø/spring Return With uto Switch (In the case of without auto switches, the,, F and P dimensions will be only changed. Refer to the dimension table.) (Through-hole): CQ2/CDQ2 H thread effective depth C oth ends tapped: CQ2/CDQ2 4 x øn through x øo counterbore O1 thread R uto switch inimum lead wire bending radius R F P (Rc, NPT, G) (Port size) oth nds Tapped O1 x 1. x 1. x 1.2 R Z ød K W J With boss on head end øth With oss on Head nd Th Note 1) With boss on rod end: Option (Suffix -C3 to the end of model number.) Width across flat 1 H1 2 Rod nd ale Thread 1 2 C1.. 2 H x 1. x 1. 1 x C1 uilt-in one-touch fittings: ø to ø V øz1 1 P1 (Piping tube O.D.) uilt-in One-touch Fittings Z1 P1 V 3.. W1. 2 W1 For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke Without auto switch With auto switch F P F P C D H J K / / x / / 1/ 1/ x 1.2 x 1.2 x Note 2) The, dimensions of the ø- mm stroke with built-in one-touch fittings without auto switch are the same as those of the ø- mm stroke without auto switch. For details about the rod end nut and accessory brackets, refer to page 1. N... O depth depth depth W 4. 1 Z 1 1 4

56 Compact Cylinder: Single cting, Single Rod Series CQ2 Foot: CQ2/CDQ2 Z F FZ H Y 4 x ød FV 4 x øfd FT 1 Rod flange: CQ2F/CDQ2F 1 T Y Y S FT Head flange: CQ2G/CDQ2G FV G Special cap bolt F FZ 4 x øfd Foot Without auto switch With auto switch S S st st st st st st st st st st st st st st st st st st D G H T Y Z Y Rod Flange Foot bracket material: Carbon steel Surface treatment: Nickel plated Without auto switch With auto switch st st st st st st st st st st st st FD FT FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated Head Flange Without auto switch With auto switch 1 st st st st st st Flange bracket material: Carbon steel Surface treatment: Nickel plated The dimensions except, and 1 are the same as those of the rod flange. arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock 1 Double clevis: CQ2D/CDQ2D 1 CT C CW 4 x N Cap bolt øcd hole H xis d CU RR C CZ Double Clevis Without auto switch With auto switch C C st st st st st st st st st st st st st st st st st st CD CT CU CW C CZ 1 N RR x 1. x 1. x 1.2 Double clevis bracket material: Cast iron Surface treatment: Painted For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. Water Resistant With uto Switch uto Switch ade to Order

57 Series CQ2 Dimensions ø to ø2/ Spring xtend Without uto Switch (Through-hole): CQ2 oth ends tapped: CQ2 O1 thread R R oth nds Tapped 2 O1 4 x. 4 x. x 1. x 1. R H thread effective depth C 4 x øn through x øo counterbore Q x. (Port size) øi Z ød K With boss on head end øth With oss on Head nd 2 G Th Note) With boss on rod end: Option (Suffix -C3 to the end of model number.) G Rod nd ale Thread C1 1 H1 4 st st x. x 1. x 1.2 x Width across flat 1 H1 C1 1 2 Stroke C D H 3 x. 4 x. x. x 1. For details about the rod end nut and accessory brackets, refer to page 1. 1 I K N O. depth 3.. depth 3. depth depth Q. Z

58 Compact Cylinder: Single cting, Single Rod Series CQ2 Foot: CQ2 H Y Special cap bolt Foot 2 st st st st st st st st D G H st... S st Z F FZ 4 x ød Rod flange: CQ2F FV 2 x øfd T 1 Y Y S FT G 2 2 T Rod Flange st st Y st Z st FD Y 4... Foot bracket material: Carbon steel Surface treatment: Nickel plated FT.. FV F FZ 4 st st st st Flange bracket material: Carbon steel Surface treatment: Nickel plated arge ore ong Stroke Rod xial Piping Head flange: CQ2G FT 1 F FZ FV 2 x øfd Head Flange 2 st st st... st... 1 st st Flange bracket material: Carbon steel Surface treatment: Nickel plated The dimensions except, and 1 are the same as those of the rod flange. nti-lateral oad With nd ock 1 Water Resistant Double clevis: CQ2D 1 CT C CU CW 4 x N Cap bolt øcd hole H xis d RR øc C CZ.1.3 Double Clevis 2 2 st st... st. 1. st... 1 st st st st C 24 N CD 4 x. 4 x. x 1. x 1. st RR C st CT 4 4 CU CW 1 1 C. CZ Double clevis bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. 2 With uto Switch uto Switch ade to Order

59 U S Series CQ2 Dimensions ø to ø2/spring xtend With uto Switch (Through-hole): CDQ2 H thread effective depth C oth ends tapped: CDQ2 R R O1 thread uto switch oth nds Tapped 2 O1 4 x. 4 x. x 1. x 1. inimum lead wire bending radius R x. (Port size) ød 2 x øn through 4 x øo counterbore V K Q H thread effective depth C S U V ø to ø2 2 x øn through 4 x øo counterbore With boss on head end øth G With oss on Head nd 2 G Th Note) With boss on rod end: Option (Suffix -C3 to the end of model number.) K ø Width across flat 1 H1 C1 Rod nd ale Thread C1 1 H1 4 st st x. x 1. x 1.2 x For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke C D H K For details about the rod end nut and accessory brackets, refer to page x. 4 x. x. x N O. depth 3.. depth 3. depth depth Q. S U V 2 2 3

60 FV Compact Cylinder: Single cting, Single Rod Series CQ2 Foot: CDQ2 Z F FZ H Y 4 x ød Rod flange: CDQ2F 2 x øfd 1 Y Y S T FT Special cap bolt G Foot st T Rod Flange st. 4. st st. 4. st Y st st Z st st FD st Y 4... Foot bracket material: Carbon steel Surface treatment: Nickel plated FT.. st FV st F D FZ 4 G st H st st st S 1 st st Flange bracket material: Carbon steel Surface treatment: Nickel plated arge ore ong Stroke Rod xial Piping Head flange: CDQ2G FT 1 2 x øfd F FZ FV Head Flange 2 st st st... st... 1 st st Flange bracket material: Carbon steel Surface treatment: Nickel plated The dimensions except, and 1 are the same as those of the rod flange. nti-lateral oad Water Resistant With nd ock 1 Double clevis: CDQ2D 1 CT C CU CW 2 x N Cap bolt øcd hole H xis d RR øc C CZ Double Clevis 2 2 st. 3. st... st. 3. st... 1 st st st st C 24 N CD 4 x. 4 x. x 1. x 1. st. 4. RR C st. 4. CT CU CW C CZ Double clevis bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. 4 With uto Switch uto Switch ade to Order

61 Series CQ2 Dimensions ø to ø/spring xtend With uto Switch (In the case of without auto switches, the,, P and Q dimensions will be only changed. Refer to the dimension table.) (Through-hole): CQ2/CDQ2 H thread effective depth C O1 thread 4 x øn through x øo counterbore P (Rc, NPT, G) (Port size) oth ends tapped: CQ2/CDQ2 R Q R inimum lead wire bending radius uto switch oth nds Tapped O1 x 1. x 1. x 1.2 R Z ød K W J With boss on head end øth 2 With oss on Head nd Th Note) With boss on rod end: Option (Suffix -C3 to the end of model number.) uilt-in one-touch fittings: ø to ø Width across flat 1 H1 C1 1 Rod nd ale Thread 1 2 C1.. 2 H1 st st st 3. x 1. x 1. 1 x V øz1 P1 (Piping tube O.D.) uilt-in One-touch Fittings Z1 P1 V W W1 For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke Without auto switch With auto switch P Q P Q C D H J K N O W Z 2 x.. 3 1/. 4 x / / 1/ 2 x /4. 1/ x depth depth depth For details about the rod end nut and accessory brackets, refer to page 1.

62 Compact Cylinder: Single cting, Single Rod Series CQ2 Foot: CQ2/CDQ2 Z F FZ H FV FT Y 4 x ød 4 x øfd FV 1 Rod flange: CQ2F/CDQ2F 1 Head flange: CQ2G/CDQ2G T Y Y S FT F FZ Special cap bolt G 4 x øfd Foot Without auto switch With auto switch S S st st st st st st st st st st st st st st st st st st D G H T Y Z st st st st st st Y Rod Flange Without auto switch With auto switch FD FT FV F FZ st st st st st st st st st st st st st st st st st st Flange bracket material: Carbon steel Surface treatment: Nickel plated Head Flange Without auto switch With auto switch st st st st st st Foot bracket material: Carbon steel Surface treatment: Nickel plated st st st 2 1 st st st 3. Flange bracket material: Carbon steel Surface treatment: Nickel plated 3. The dimensions except, and 1 are the same as those of the rod flange. Water Resistant arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock 1 Double clevis: CQ2D/CDQ2D 1 CT C CW 4 x N Cap bolt øcd hole H xis d CU RR C CZ Double Clevis st. Without auto switch With auto switch C C st st st st st st st st st st st st st st st st st CD CT CU CW C CZ 1 st st st st st st N x 1. x 1. x 1.2 Double clevis bracket material: Cast iron Surface treatment: Painted For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. RR With uto Switch uto Switch ade to Order

63 Without auto switch With auto switch With auto switch (uilt-in magnet) CQ2 3 DC CDQ2 ounting Through-hole/oth ends tapped common () Cylinder mounting bolts are not included. Order them separately referring to ounting olt for CQ2 on page. 1 1 uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ21-3DCZ Compact Cylinder: arge ore Double cting, Single Rod Series CQ2 ø, ø1, ø, ø1, ø mm 1 mm mm 1 mm mm Port thread type Nil TN TF Rc NPT G Cylinder stroke Refer to the next page for standard strokes. D How to Order 3 DC ction Double acting Z Z W uto switch mounting groove Z ø to ø 4 surfaces ody option Nil Cushion C Rubber bumper ade to Order Refer to the next page for details. Number of auto switches Nil S n 2 pcs. 1 pc. n pcs. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. (Rod end female thread) pplicable uto Switches/Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) lectrical entry Grommet Grommet Indicator light Yes Yes No Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN equivalent) 2-wire 24 V 24 V oad voltage DC Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW Solid state auto switches marked with are produced upon receipt of order. 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ V, V V V, V V V, V V C V V V V, V V or less uto switch model Perpendicular NV PV V NWV PWV WV NV PV V V 3V V There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2. In-line N P NW PW W N P 3 ead wire length (m). (Nil) 1 () 3 () None (Z) (N) Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC

64 Compact Cylinder: arge ore Double cting, Single Rod Series CQ2 Specifications 1 1 ction Fluid Proof pressure Double acting, Single rod ir 1. Pa 1. Pa aximum operating pressure 1. Pa. Pa inimum operating pressure mbient and fluid temperature ubrication. Pa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Not required (Non-lube) arge ore Piston speed to mm/s to mm/s JIS Symbol Double acting, Single rod llowable kinetic energy (J) Stroke length tolerance mm Note) Note) Stroke length tolerance does not include the amount of bumper change. Strokes, 1, 1, stroke,, 3,,,,,, 1, 1,, 2, 3 ong Stroke Rod Symbol ade to Order (For details, refer to pages 1 to.) Specifications Intermediate stroke (xclusive body type) Fluororubber seals, ø to ø only anufacture of Intermediate Strokes Type Part no. Description spacer is installed in the standard stroke body. Refer to How to Order for the standard model number. (P. ) Strokes in mm intervals are available by installing a spacer in the standard stroke cylinder. xclusive body (-) Suffix - to the end of standard model number. (P. ) Strokes in 1 mm intervals are available by using an exclusive body with the specified stroke. xial Piping nti-lateral oad Stroke range xample to Stroke range to 2 Part no.: CQ2-DCZ CQ2-1DCZ with mm width spacer inside The dimension is 2 mm. to Stroke range to 2 Part no.: CQ2-DCZ- akes mm stroke tube. The dimension is 2 mm. With nd ock Refer to pages to 1 for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Water Resistant ade to Order uto Switch With uto Switch

65 Series CQ2 Theoretical Output 1 1 Operating direction IN OUT IN OUT IN OUT IN OUT IN OUT OUT IN Operating pressure (Pa) (N) Weight Without uto Switch With uto Switch Cylinder stroke Cylinder stroke (kg) (kg) dditional Weight Rod end male thread ale thread Nut (kg) Calculation: (xample) CDQ2-3DCZ asic weight: CDQ2-3DCZ. kg dditional weight:.4 kg.24 kg ounting olt for CQ2 ounting method: ounting bolt for through-hole mounting of the CQ2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-x 4 pcs. Note 1) To install a through-hole type mounting bolt, make sure to use the flat washer that is provided. Note 2) For mounting bolts for the stroke length exceeding mm, use the O screw provided on the cylinder tube to secure the cylinder. aterial: Chromium molybdenum steel Surface treatment: Nickel plated O D C Cylinder model C D CQ2/1-DCZ -DCZ -3DCZ -DCZ -DCZ -DCZ -DCZ CQ2-DCZ -DCZ -3DCZ -DCZ -DCZ -DCZ -DCZ ounting bolt part no. CQ- x x 1 x x x 1 x x 1 CQ- x 1 x x x 1 x 1 x 1 x Cylinder model C D CQ21-DCZ -DCZ -3DCZ -DCZ -DCZ -DCZ -DCZ CQ2-DCZ -DCZ -3DCZ -DCZ -DCZ -DCZ -DCZ ounting bolt part no. CQ-1 x x x x 1 x x 1 x 21 CQ-1 x x x 1 x x 1 x x

66 Compact Cylinder: arge ore Double cting, Single Rod Series CQ2 Construction arge ore Component Parts No Description Cylinder tube Head cover Piston Piston rod Rod cover Retaining ring umper ushing Wear ring agnet Rod end nut Piston seal Rod seal Tube gasket aterial luminum alloy Carbon steel luminum alloy Carbon steel Carbon steel Carbon tool steel Urethane earing alloy Resin Carbon steel NR NR NR Note Hard anodized Nickel plated Chromated Hard chrome plated Nickel plated Phosphate coated For CDQ2 only Nickel plated Replacement Parts/Seal Kit Kit no. Contents 1 1 CQ2-PS CQ21-PS CQ2-PS CQ21-PS CQ2-PS Kits include items!2,!3,!4 from the table. Seal kit includes!2,!3,!4. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) ong Stroke Rod xial Piping nti-lateral oad Rod nd Nut Part no. NT- NT- pplicable bore size, 1, 1, d H C D 3 x 1. 3 x 1. aterial: Carbon steel Surface treatment: Nickel plated Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. With nd ock Water Resistant With uto Switch uto Switch ade to Order

67 Series CQ2 Dimensions ø to ø (Through-hole): CQ2 H thread effective depth C 2 x 4 x øo counterbore depth R (lso back cover) The dimensions are the same with or without an auto switch. Q uto switch inimum lead wire bending radius Q 2 x P (Rc, NPT, G) (Port size) 2 2. ød 4 x øn through K W J Note) With flat washer 4 pcs. 2 x 4 x O thread depth R + Stroke + Stroke Width across flat 1 H1 C1 1 Rod nd ale Thread 1 1 C1 H x 1. 3 x 1. 3 x stroke,, 3,,,,, 1 1,, 2, C D H x 2. x x 3 J K 3 Note) e sure to use the attached flat washer for mounting cylinder with through-holes N... O x 2 x 2 x 2 O P 3/ 3/ 3/ Q R R W 1 1

68 Dimensions ø1, ø ø1 24 x 3 thread effective depth 33 2 x 4 x ø31. counterbore depth 2 (lso back cover) Compact Cylinder: arge ore Double cting, Single Rod uto switch inimum lead wire bending radius x Rc, NPT, G 1/2 (Port size) Series CQ2 The dimensions are the same with or without an auto switch ø 2 2 arge ore With flat washer Note 2) 4 pcs. 1 2 x 4 x x 2. thread depth 3 Note 1) 2 + Stroke + Stroke 4 x ø1 through ong Stroke Width across flat 3 x Note 1) In the case of mm stroke or less, it would come with 2 x 4 x x 2. through thread. Note 2) e sure to use the attached flat washer for mounting cylinder with through-holes. Rod xial Piping 4 ø 24 x 3 thread effective depth 33 2 x 4 x ø31. counterbore depth 2 (lso back cover) ø 3 3 uto switch inimum lead wire bending radius 3 2 x Rc, NPT, G 1/2 (Port size) 2 2 nti-lateral oad With nd ock Water Resistant 3 12 With flat washer Note 2) 4 pcs. Width across flat 3 x x 4 x x 2. thread depth 3 Note 1) + Stroke + Stroke 4 x ø1 through Note 1) In the case of mm stroke or less, it would come with 2 x 4 x x 2. through thread. Note 2) e sure to use the attached flat washer for mounting cylinder with through-holes. With uto Switch uto Switch ade to Order

69 Compact Cylinder: arge ore Double cting, Double Rod Series CQ2W ø, ø1, ø, ø1, ø How to Order Without auto switch CQ2W 3 DC Z With auto switch CDQ2W 3 DC Z W With auto switch (uilt-in magnet) W Type Double rod ounting Through-hole/oth ends tapped common () Cylinder mounting bolts are not included. Order them separately referring to ounting olt for CQ2W on page. uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2W1-3DCZ 1 1 mm 1 mm mm 1 mm mm Port thread type Nil TN TF Rc NPT G Cylinder stroke Refer to the next page for standard strokes. ade to Order Refer to the next page for details. Number of auto switches Nil S n 2 pcs. 1 pc. n pcs. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. uto switch mounting groove Z ø to ø 4 surfaces ody option Nil Cushion C Rubber bumper ction D Double acting (Rod end female thread) pplicable uto Switches/Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) lectrical entry Grommet Indicator light Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN equivalent) 24 V oad voltage DC V, V V V, V V V, V V C uto switch model Perpendicular NV PV V NWV PWV WV NV PV V In-line N P NW PW W N P ead wire length (m). (Nil) 1 () 3 () None (Z) (N) Grommet V V Yes V V 3V 3 2-wire 24 V No V, V V or less V Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW Solid state auto switches marked with are produced upon receipt of order. 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2. Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC

70 Compact Cylinder: arge ore Double cting, Double Rod Series CQ2W Specifications Symbol JIS Symbol Double acting, Double rod ade to Order (For details, refer to pages 1 to.) Specifications - Intermediate stroke (xclusive body type) -23 Special rod end for double rod cylinder -21 Fluororubber seals, ø to ø only Intermediate stroke of double rod cylinder, -3 ø to ø only -3: Intermediate stroke in mm intervals only 1 1 ction Fluid Proof pressure aximum operating pressure inimum operating pressure Double acting, Double rod ir 1. Pa 1. Pa. Pa 1. Pa. Pa mbient and fluid temperature ubrication Piston speed llowable kinetic energy (J) Stroke length tolerance Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Not required (Non-lube) to mm/s to mm/s mm Note) Note) Stroke length tolerance does not include the amount of bumper change. Strokes, 1, 1, Type Part no. stroke,, 3,,,,,, 1, 1,, 2, 3 anufacture of Intermediate Strokes Description Stroke range xample spacer is installed in the standard stroke body. Suffix -3 to the end of standard model number. (P. ) Strokes in mm intervals are available by installing a spacer in the standard stroke cylinder. to Stroke range to 2 Part no.: CQ2W-DCZ-3 CQ2W-1DCZ with mm width spacer inside The dimension is 2 mm. xclusive body (-) Suffix - to the end of standard model number. (P. ) Strokes in 1 mm intervals are available by using an exclusive body with the specified stroke. to Stroke range to 2 Part no.: CQ2W-DCZ- akes mm stroke tube. The dimension is 2 mm. arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Refer to pages to 1 for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Water Resistant ade to Order uto Switch With uto Switch 4

71 Series CQ2W Retaining Ring Installation/Removal Theoretical Output Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. ounting Warning Do not apply reverse torque to the piston rods sticking out from both sides of this cylinder at the same time. The torque makes connection threads inside loosen, which may cause an accident or malfunction. Install or remove loads while the piston rod width across flat is secured. Do not fix the other side of the piston rod width across flat and apply reverse torque. Weight 1 1 Without uto Switch With uto Switch Operating pressure (Pa) Cylinder stroke Cylinder stroke (N) (kg) (kg) dditional Weight ale thread.2 Nut. Calculation: (xample) CDQ2W-3DCZ asic weight: CDQ2W-3DCZ. kg dditional weight:.4 kg. kg 1.2. (kg), 1,..2

72 Compact Cylinder: arge ore Double cting, Double Rod Series CQ2W ounting olt for CQ2W ounting method: ounting bolt for through-hole mounting of the CQ2W is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-x 4 pcs. Note 1) To install a through-hole type mounting bolt, make sure to use the flat washer that is provided. Note 2) For mounting bolts for the stroke length exceeding mm, use the O screw provided on the cylinder tube to secure the cylinder. Cylinder model C D CQ2W/1-DCZ -DCZ -3DCZ -DCZ -DCZ -DCZ -DCZ CQ2W-DCZ -DCZ -3DCZ -DCZ -DCZ -DCZ -DCZ aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt part no. CQ- x x 1 x x x 1 x x 1 CQ- x 1 x x x 1 x 1 x 1 x O thread part Cylinder model C D CQ2W1-DCZ -DCZ -3DCZ -DCZ -DCZ -DCZ -DCZ CQ2W-DCZ -DCZ -3DCZ -DCZ -DCZ -DCZ -DCZ ounting bolt ounting bolt part no. CQ-1 x x x x 1 x x 1 x 21 CQ-1 x x x 1 x x 1 x x arge ore ong Stroke Rod Construction With nd ock nti-lateral oad xial Piping Component Parts No Description Cylinder tube Piston Piston rod Piston rod Rod cover Retaining ring umper ushing agnet Rod end nut Piston seal Rod seal Tube gasket Piston gasket aterial luminum alloy luminum alloy Carbon steel Carbon steel Carbon steel Carbon tool steel Resin earing alloy Carbon steel NR NR NR NR Note Hard anodized Chromated Hard chrome plated Hard chrome plated Nickel plated Phosphate coated For CDQ2W only Nickel plated Replacement Parts/Seal Kit Kit no. Contents 1 1 CQ2W-PS CQ2W1-PS CQ2W-PS CQ2W1-PS CQ2W-PS Kits include items!1,!2,!3 from the table. Seal kit includes!1,!2,!3. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) Rod nd Nut Water Resistant With uto Switch uto Switch Part no. NT- NT- pplicable bore size, 1, 1, aterial: Carbon steel Surface treatment: Nickel plated d H C D 3 x 1. 3 x ade to Order

73 Series CQ2W Dimensions ø to ø (Through-hole): CQ2W 2 x H thread effective depth C (lso back cover) 2 x 4 x øo counterbore depth R (lso back cover) The dimensions are the same with or without an auto switch. Q Q uto switch inimum lead wire bending radius 2 x P (Rc, NPT, G) (Port size) Width across flat K 2 ød ød 2. K W J With flat washer Note 1) 4 pcs. 2 x 4 x O thread depth R + Stroke + 2 (Stroke) 4 x øn through-hole + Stroke 1 1 Rod nd ale Thread x 1. 3 x 1. 3 x 1. C1 H H1 C1 H1 C Stroke (Stroke) stroke Note 2) C 1,, 3,,,,, 1 1,, 2, (.) 3 (.) 33 (2.) D H x 2. x x 3 Note 1) e sure to use the attached flat washer for mounting cylinder with through-holes. Note 2) ( ): Values of effective length in one side, only for mm stroke model The positions of double rod width across flats are not the same. J K N... O x 2 x 2 x 2 O P 3/ 3/ 3/ Q R R W 1

74 Dimensions ø1, ø ø1 2 x 24 x 3 effective thread depth 33 (lso back cover) 2 x 4 x ø31. counterbore depth 2 (lso back cover) Compact Cylinder: arge ore Double cting, Double Rod uto switch inimum lead wire bending radius x Rc, NPT, G 1/2 (Port size) Series CQ2W The dimensions are the same with or without an auto switch. 3 ø ø x ø1 through arge ore With flat washer Note 2) 4 pcs. Width across flat 1 2 x 4 x x 2. thread depth 3 Note 1) 2 + Stroke + 2 (Stroke) 1 + Stroke Width across flat 3 x 1. 3 x 1. Note 1) In the case of mm stroke or less, it would come with 2 x 4 x x 2. through thread. Note 2) e sure to use the attached flat washer for mounting cylinder with through-holes. ong Stroke Rod Stroke xial Piping (Stroke) ø 2 x 24 x 3 effective thread depth 33 (lso back cover) 2 x 4 x ø31. counterbore depth 2 (lso back cover) ø 3 3 uto switch inimum lead wire bending radius 3 2 x Rc, NPT, G 1/2 (Port size) ø Width across flat x ø1 through nti-lateral oad With nd ock Water Resistant 3 12 With flat washer Note 2) 4 pcs. Width across flat 1 2 x 4 x x 2. thread depth 3 Note 1) + Stroke (Stroke) 1 + Stroke Width across flat 3 x 1. 3 x 1. 3 Note 1) In the case of mm stroke or less, it would come with 2 x 4 x x 2. through thread. Note 2) e sure to use the attached flat washer for mounting cylinder with through-holes. With uto Switch uto Switch The positions of double rod width across flats are not the same (Stroke) Stroke ade to Order

75 Without auto switch With auto switch Compact Cylinder: ong Stroke Double cting, Single Rod Series CQ2 ø, ø, ø, ø, ø, ø CQ2 CDQ2 How to Order DC DC Z Z W F G D With auto switch (uilt-in magnet) ounting oth ends tapped Foot Rod flange Head flange Double clevis ounting brackets are shipped together, (but not assembled). Nil TN TF F uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2-DCZ mm mm mm mm mm mm Port thread type Rc NPT G uilt-in one-touch fittings Note) Note) s available with one-touch fittings are ø to ø. Cylinder stroke Refer to the next page for standard strokes. D ction Double acting Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. ade to Order Refer to the next page for details. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. uto switch mounting groove Z 4 surfaces ody option Nil Cushion C Rubber bumper (Rod end female thread) Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. pplicable uto Switches/ Refer to the individual catalog (S-1) for the D-P3DW type. Type Solid state auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) agnetic field resistant (2-color indication) lectrical entry Grommet Indicator light Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 2-wire (Non-polar) oad voltage DC C 24 V V, V V V, V V V, V V uto switch model Perpendicular NV PV V NWV PWV WV NV PV V In-line N P NW PW W N P P3DW ead wire length (m). (Nil) 1 () 3 () None (Z) (N) Pre-wired connector 3-wire V V Yes (NPN equivalent) Grommet V V 3V 3 2-wire 24 V No V, V V or less V Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW Solid state auto switches marked with are produced upon receipt of order. Reed auto switch 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2. pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC

76 Compact Cylinder: ong Stroke Double cting, Single Rod Series CQ2 Specifications JIS Symbol Double acting, Single rod ction Fluid Proof pressure aximum operating pressure inimum operating pressure mbient and fluid temperature ubrication Piston speed Double acting, Single rod ir 1. Pa 1. Pa. Pa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Not required (Non-lube) to mm/s llowable kinetic energy (J) Stroke length tolerance mm 1.4 Note) Note) Stroke length tolerance does not include the amount of bumper change. Strokes,,,, stroke, 1, 1,, 2, 3 arge ore ong Stroke Rod Symbol - -C4 -C -C2-21 ade to Order (For details, refer to pages 1 to.) Specifications Intermediate stroke (xclusive body type) With heavy-duty scraper Piston rod/retaining ring/rod end nut material: Stainless steel With split pins for double clevis pin/ double knuckle joint pin and flat washers Fluororubber seals anufacture of Intermediate Strokes Type Part no. Description Stroke range xample spacer is installed in the standard stroke body. Refer to How to Order for the standard model number. (P. ) Strokes in 1 mm intervals are available by installing a spacer in the standard stroke cylinder. to Stroke range 1 to 2 Part no.: CQ2-DCZ CQ2-1DCZ with mm width spacer inside The dimension is 23. mm. xclusive body (-) Suffix - to the end of standard model number. (P. ) Strokes in 1 mm intervals are available by using an exclusive body with the specified stroke. to Stroke range 1 to 2 Part no.: CQ2-DCZ- akes mm stroke tube. The dimension is 1. mm. xial Piping nti-lateral oad With nd ock Type Pneumatic uilt-in magnet Rc1/ Pipe thread TN NPT1/ Piping TF G1/ uilt-in one-touch fittings Note) ø/4 Note) One-touch fittings cannot be replaced. Rc1/ NPT1/ G1/ ø/4 Rc1/4 NPT1/4 G1/4 ø/ Rc1/4 NPT1/4 G1/4 ø/ Rc3/ NPT3/ G3/ Refer to pages to 1 for the specifications of cylinders with auto switches. Rc3/ NPT3/ G3/ uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Water Resistant With uto Switch uto Switch ade to Order

77 Series CQ2 Copper and Fluorine-free Series (For CRT anufacturing Process) CQ2 Stroke DC()Z ø, ø, ø, ø ø, ø Copper and fluorine-free series For preventing the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. Specifications ction Proof pressure ax. operating pressure Rubber bumper Double acting, Single rod 1. Pa 1. Pa With () Piping Piston speed ounting uto switch Pipe thread, uilt-in one-touch fittings to mm/s oth ends tapped ountable llowable ateral oad at Rod nd llowable lateral load at rod end W (N) 3 ø ø ø ø ø ø (ounting: Horizontal) Cylinder stroke ounting rackets/ Part No. Foot Note 1) Flange CQ- CQ- CQ- CQ- CQ- CQ- CQ-F CQ-F CQ-F CQ-F CQ-F CQ-F Double clevis CQ-D CQ-D CQ-D CQ-D CQ-D CQ-D Note 1) When ordering a foot bracket, order 2 pieces per cylinder. Note 2) Parts belonging to each bracket are as follows. Foot or Flange: ody mounting bolts Double clevis: Clevis pin, ody mounting bolts, Type C retaining rings for axis Theoretical Output (N) Operating direction IN OUT IN OUT IN OUT Operating pressure (Pa) Operating direction IN OUT IN OUT IN OUT Operating pressure (Pa) Weight (g) Without uto Switch Cylinder stroke With uto Switch Cylinder stroke dditional Weight Rod end ale thread male thread Nut Foot (Including mounting bolts) Rod flange (Including mounting bolts) Head flange (Including mounting bolts) Double clevis (Including pin, retaining rings, bolts) (g) Calculation: (xample) CQ2D-DCZ asic weight: CQ2-DCZ 1 g dditional weight: 43 g Double clevis g g dd each weight of auto switches when auto switches are mounted. 1

78 Compact Cylinder: ong Stroke Double cting, Single Rod Series CQ2 Construction uto switch (CDQ2 only) uilt-in one-touch fittings Rod arge ore ong Stroke Component Parts No Description Cylinder tube Piston Piston rod Collar ottom plate Retaining ring umper umper ushing Wear ring Rod end nut agnet One-touch fitting Rod seal Piston seal Tube gasket Retaining Ring Installation/Removal Caution aterial luminum alloy luminum alloy Carbon steel luminum alloy luminum alloy Carbon tool steel Urethane Urethane earing alloy Resin Carbon steel NR NR NR Note Hard anodized Chromated Hard chrome plated nodized nodized Phosphate coated Nickel plated For CDQ2 only ø to ø 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. Replacement Parts/Seal Kit Kit no. Contents CQ2--PS CQ2--PS Kits include items CQ2--PS!4,!,! from the CQ2--PS table. CQ2--PS CQ2--PS Seal kit includes!4,!,!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order 2

79 Series CQ2 Dimensions ø to ø oth ends tapped: CQ2 The dimensions are the same with or without an auto switch. H thread effective depth C x O thread effective depth R Q 2 x P (Rc, NPT, G) (Port size) uto switch inimum lead wire bending radius Q Z øth ød K W J + Stroke + Stroke Width across flat 1 H1 Rod nd ale Thread 1 2 C1.. 2 H x 1. x 1. 1 x C1 1 The dimensions with built-in one-touch fittings are equivalent to those of the CQ2 series, double acting, single rod. Refer to page 1. oth nds Tapped For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke range C D H J K O P Q R Th W Z x x 1. 1/ to Note 1) 2 2 x x 1. 1/ , x x 1.2 1/ Note 1) For to strokes, strokes are available in 2 mm intervals. Note 2) For calculation on the longitudinal dimension of intermediate strokes, refer to page. Foot: CQ2 Special cap bolt Z H Y 4 x ød Y T + Stroke S + Stroke + Stroke Y G Foot D G 4 4 H S T Y 4 Z Y Foot bracket material: Carbon steel Surface treatment: Nickel plated For details about the rod end nut and accessory brackets, refer to page

80 Compact Cylinder: ong Stroke Double cting, Single Rod Series CQ2 The dimensions are the same with or without an auto switch. Rod flange: CQ2F F FZ FV 4 x øfd FT + Stroke + Stroke Rod Flange FD FT FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated arge ore ong Stroke Head flange: CQ2G 1 Special cap bolt Rod + Stroke + Stroke FT FV F FZ 4 x øfd Head Flange. 2. Flange bracket material: Carbon steel Surface treatment: Nickel plated The dimensions except are the same as those of the rod flange. xial Piping With nd ock nti-lateral oad 1 Double clevis: CQ2D + Stroke C + Stroke + Stroke CT CU CW 4 x N Cap bolt øcd hole H xis d RR C CZ Double Clevis CD C CT CU x 1. x 1. x N RR Double clevis bracket material: Cast iron Surface treatment: Painted CW 2 C 1 1 CZ Water Resistant With uto Switch uto Switch 1 For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are shipped together. ade to Order 4

81 Series CQ2 Dimensions ø to ø oth ends tapped: CQ2 The dimensions are the same with or without an auto switch. H thread effective depth C x O thread effective depth R 2 x P (Port size) Q inimum lead wire bending radius uto switch Q Z øth ød K W J Width across flat 1 H1 + Stroke + Stroke Rod nd ale Thread 1 C1 H x 1. x 1. 2 x C1 1 The dimensions with built-in one-touch fittings are equivalent to those of the CQ2 series, double acting, single rod. Refer to page 1. oth nds Tapped For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke range C D H J K O P Q R Th W Z 1 x x 1. 1/ to Note 1) 21 2 x 2. x 1. 3/ , x x 1. 3/ Note 1) For to strokes, strokes are available in 2 mm intervals. Note 2) For calculation on the longitudinal dimension of intermediate strokes, refer to page. Foot: CQ2 + Stroke Y Special cap bolt H Z 4 x ød Y T S + Stroke + Stroke Y G 1 Foot D G H 4 1 S For details about the rod end nut and accessory brackets, refer to page 1. T Y Z Y Foot bracket material: Carbon steel Surface treatment: Nickel plated

82 Compact Cylinder: ong Stroke Double cting, Single Rod Series CQ2 Rod flange: CQ2F F FZ FV 4 x øfd FT + Stroke + Stroke The dimensions are the same with or without an auto switch. Rod Flange FD FT FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated arge ore ong Stroke Head flange: CQ2G 1 Rod + Stroke + Stroke FT FV F FZ 4 x øfd Head Flange 4. Flange bracket material: Carbon steel Surface treatment: Nickel plated The dimensions except are the same as those of the rod flange. xial Piping nti-lateral oad 1 With nd ock Double clevis: CQ2D + Stroke C + Stroke + Stroke CT CU CW 4 x N Cap bolt øcd hole H xis d RR C CZ Double Clevis CD C CT CU x 1. x 1. x 1. 1 N RR Double clevis bracket material: Cast iron Surface treatment: Nickel plated CW C 2 CZ 44 4 Water Resistant With uto Switch uto Switch 1 For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are shipped together. ade to Order

83

84 Without auto switch ø to ø2 Without auto switch ø to ø With auto switch Compact Cylinder: Rod Double cting, Single Rod Series CQ2K ø, ø, ø, ø2, ø, ø, ø, ø CQ2K CQ2K CDQ2K With auto switch (uilt-in magnet) rod ounting Through-hole () ø to ø oth ends tapped Foot ø, ø, F Rod flange ø G Head flange D Double clevis ounting brackets are shipped together, (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to ounting olt for C(D)Q2K on pages 2 and 4. Note 1) 2 mm mm mm 2 mm mm mm mm mm Note 1) When ø with auto switch is required, the body option should be with rubber bumper (C). xample) CDQ2K-3DCZ Nil TN TF F Port thread type thread ø to ø2 Rc NPT ø to ø G uilt-in one-touch fittings Note 2) Note 2) s available with one-touch fittings are ø to ø. For cylinders without auto switch, threads are compatible only for ø- mm stroke model. How to Order Cylinder stroke Refer to the next page for standard strokes. 3 D 3 D 3 D NV PV V NWV PWV WV NV PV V Z Z N P NW PW W N P P3DW W Number of auto switches Nil S n 2 pcs. 1 pc. n pcs. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. uto switch mounting groove Z ody option Nil F C ø to ø2 ø to ø 2 surfaces 4 surfaces ade to Order Refer to the next page for details. (Rod end female thread) With boss on head end With rubber bumper (ø with auto switch only) Combination of body options ( F ) is available. ction D Double acting Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. pplicable uto Switches/ Refer to the individual catalog (S-1) for the D-P3DW type. Type Solid state auto switch Special function lectrical entry Grommet Indicator light Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 2-wire (Non-polar) oad voltage DC C uto switch model Perpendicular In-line uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2K-3DZ ead wire length (m) 3-wire V V Yes (NPN equivalent) Grommet V V 3V 3 2-wire 24 V No V, V V or less V Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW Reed auto switch Diagnostic indication (2-color indication) Water resistant (2-color indication) agnetic field resistant (2-color indication) 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ 24 V V, V V V, V V V, V V There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2.. (Nil) 1 () 3 () None (Z) (N) Pre-wired connector Solid state auto switches marked with are produced upon receipt of order. The D-P3DW type is available from ø to ø only. pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

85 Series CQ2K Specifications Symbol rod 2 ction Fluid Proof pressure aximum operating pressure inimum operating pressure. Pa Double acting, Single rod ir 1. Pa 1. Pa. Pa mbient and fluid temperature ubrication Piston speed llowable kinetic energy (J). Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Not required (Non-lube) to mm/s Note 1) Stroke length tolerance +1. mm Note 2) Rod non-rotating accuracy ±2 ±1 ±. ø with auto switch: With rubber bumper () Note 1) For cylinders with rubber bumper (ø with auto switch only) Note 2) Stroke length tolerance does not include the amount of bumper change. Symbol - - -C -C -C -C -C2 ade to Order (For details, refer to pages 1 to.) Specifications Special rod end shape Intermediate stroke (xclusive body type): ø to ø djustable stroke cylinder/djustable extension type djustable stroke cylinder/djustable retraction type Dual stroke cylinder/double rod Dual stroke cylinder/single rod With split pins for double clevis pin/ double knuckle joint pin and flat washers -1 Cylinder tube: With concave boss on head end Refer to pages to 1 for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Strokes,, 2,, stroke,, 1,, 2, 3,, 1,, 2, 3, 3,, 4,,, 1,, 2, 3, 3,, 4,,,, 1,, 2, 3, 3,, 4,,, anufacture of Intermediate Strokes Type spacer is installed in the standard stroke body. Part no. Refer to How to Order for the standard model number. (P. ) Description Strokes in 1 mm intervals are available by installing a spacer in the standard stroke cylinder. Stroke range Stroke range, 1 to 2, 2 1 to 4 to 1 to Part no.: CQ2K-DZ xample CQ2K-DZ with 1 mm width spacer inside The dimension is. mm. Type 2 Through-hole () ounting oth ends tapped uilt-in magnet Note 1) Pipe x. x. x. x. x. Rc1/ Rc1/ Rc1/4 Rc1/4 Piping thread TN TF NPT1/ G1/ NPT1/ G1/ NPT1/4 G1/4 NPT1/4 G1/4 uilt-in one-touch fittings With boss on head end ø/4 Note 2) ø/4 ø/ ø/ Note 1) ø without auto switch: x. is used for mm stroke piping dimension. Thus, do not enter a symbol for the port thread type. Note 2) The dimensions of the ø- mm stroke with built-in one-touch fittings are the same as those of the mm stroke cylinder tube. Pneumatic

86 Compact Cylinder: Rod Double cting, Single Rod Series CQ2K Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. ounting 1. Install or remove loads while the piston rod width across flat is secured. 2. Using a non-rotating rod cylinder void using the air cylinder in such a way that rotational torque would be applied to the piston rod. If rotational torque is applied, the non-rotating guide will deform, causing a loss of non-rotating accuracy. Use the below table as a guide for the allowable rotational torque ranges. llowable rotational torque N m or less Operate the cylinder in such a way that the load to the piston rod is always applied in the axial direction. 3. When a work piece is secured to the end of the piston rod, ensure that the piston rod is retracted entirely, and place a wrench on the portion of the rod that protrudes beyond the section. lso, tighten in a way that prevents the tightening torque from being applied to the non-rotating guide. ounting rackets/part No. Weight 2 Foot Note 1) Flange CQ- CQ- CQ- CQ-F CQ-F CQ-F Double clevis CQ-D CQ-D CQ-D Note 1) When ordering a foot bracket, order 2 pieces per cylinder. Note 2) Parts belonging to each bracket are as follows. Foot or Flange: ody mounting bolts Double clevis: Clevis pin, ody mounting bolts, Type C retaining rings for axis Weight dditional Weight Theoretical Output Operating direction IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT 2 3 (N) Operating pressure (Pa) (g) Cylinder stroke oth ends tapped ale thread Nut With boss on head end uilt-in one-touch fittings Foot (Including mounting bolts) Rod flange (Including mounting bolts) Head flange (Including mounting bolts) Double clevis (Including pin, retaining rings, bolts) Calculation: (xample) CQ2KD-DZ asic weight: CQ2K-DZ 2 g dditional weight: oth ends tapped g 44 g Double clevis 1 g 1 g (g) arge ore ade to Order ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant uto Switch With uto Switch

87 Series CQ2K Construction (ø to ø) (ø to ø) uilt-in one-touch fittings With boss on head end Component Parts No Description Cylinder tube Piston Piston rod 4 Rod cover 1 Collar Retaining ring ushing Hexagon socket head cap screw Hexagon socket head set screw Rod end nut Centering location ring One-touch fitting Piston seal Rod seal Tube gasket aterial luminum alloy luminum alloy Stainless steel Carbon steel rass luminum alloy luminum alloy Carbon tool steel Oil-impregnated sintered alloy lloy steel lloy steel Carbon steel luminum alloy NR NR NR Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø, lectroless nickel plated ø to ø, nodized ø to ø, nodized Phosphate coated ø to ø ø to ø, Nickel plated ø to ø, Nickel plated Nickel plated ø to ø, nodized ø to ø Replacement Parts/Seal Kit Kit no. Contents CQ2K-PS CQ2K-PS CQ2K-PS Kits include items 2 CQ2K2-PS!3,!4,! from the CQ2K-PS table. CQ2K-PS CQ2K-PS CQ2K-PS Seal kit includes!3,!4,!. Order the seal kit based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) 1

88 Compact Cylinder: Rod Double cting, Single Rod Series CQ2K ounting olt for CQ2K/Without uto Switch ounting method: ounting bolt for through-hole mounting of the CQ2K is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x3 2 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated Head end mounting ounting bolt ounting bolt Rod end mounting Cylinder model C D ounting bolt part no. C' D' ounting bolt part no. CQ2K-D -D 3 3 CQ-3 x 3 x CQ-3 x 3 x 3-1D. x. x -D 4 x 4 4 x 4-2D -3D CQ2K-D -D 3 3 x x CQ-3 x 3 x x x CQ-3 x 3 x 3-1D x x -D 4 x 4 4 x 4-2D -3D CQ2K-D -D -1D -D 3 4 x x CQ- x 3 x x 4 x 3 4 x x CQ- x 3 x x 4 x -2D x x. -3D x x -3D -D -4D -D CQ2K2-D -D -1D -D 4 x x x x CQ- x x 4 x x 3 4 x x x x CQ- x 3 x x 4 x -2D x x. -3D x x -3D -D -4D -D CQ2K-DZ -DZ -1DZ -DZ -2DZ 4 x x x x CQ- x x 4 x x x 4 x x x x CQ- x x 4 x x x -3DZ x x. -3DZ x x -DZ -4DZ -DZ -DZ -DZ x x x x x x x x x x Copper and Fluorine-free Series (For CRT anufacturing Process) Cylinder model C D ounting bolt part no. C' D' ounting bolt part no. CQ2K-DZ -DZ -1DZ -DZ -2DZ 3 4 CQ- x 3 x x 4 x x 3 4 CQ- x 3 x x 4 x x -3DZ x x.. -3DZ x x -DZ -4DZ -DZ -DZ -DZ CQ2K-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ -DZ CQ2K-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ -DZ x x x x x 1 CQ- x 4 x x x x x x x x x x CQ- x x x x x x x x x x x x x x x x 1 CQ- x 4 x x x x x x x x x x CQ- x x x x x x x x x x x 1 arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch CQ2K Stroke D()Z Copper and fluorine-free series ø, ø, ø2, ø ø, ø, ø For preventing the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. Specifications ction Proof pressure ax. operating pressure Rubber bumper Piping Piston speed ounting uto switch 2 Double acting, Single rod 1. Pa 1. Pa None Pipe thread to mm/s Through-hole ountable uto Switch ade to Order 2

89 Rod: Double cting, Single Rod Series CDQ2K With uto Switch Refer to the below pages for further information on auto switches. uto switch proper mounting position and its mounting height inimum stroke for auto switch mounting P. to 1 Operating range uto switch mounting brackets/part no. Weight Weight (g) dditional Weight (g) Cylinder stroke oth ends tapped Rod end male thread ale thread Nut With boss on head end uilt-in one-touch fittings Foot (Including mounting bolts) Rod flange (Including mounting bolts) Head flange (Including mounting bolts) Double clevis (Including pin, retaining rings and bolts) Calculation: (xample) CDQ2KD-2DZ dd each weight of auto switches asic weight: CDQ2K-2DZ g when auto switches are mounted. dditional weight: oth ends tapped g 44 g Double clevis 1 g 2 g Construction ø to ø2 ø ø to ø Component Parts No Description Cylinder tube Piston Piston rod Rod cover Collar Retaining ring ushing Hexagon socket head cap screw Hexagon socket head cap screw Hexagon socket head set screw agnet Piston seal Rod seal Tube gasket aterial luminum alloy luminum alloy Stainless steel Carbon steel rass luminum alloy luminum alloy Carbon tool steel Oil-impregnated sintered alloy lloy steel lloy steel lloy steel NR NR NR Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø, lectroless nickel plated ø to ø, nodized ø to ø, nodized Phosphate coated ø to ø ø to ø2, Nickel plated ø, Nickel plated ø to ø, Nickel plated Replacement Parts/Seal Kit (Pneumatic type (Non-lube)) 2 Kit no. CQ2K-PS CQ2K-PS CQ2K-PS CQ2K2-PS CQ2K-PS CQ2K-PS CQ2K-PS CQ2K-PS Contents Kits include items!2,!3,!4 from the table. Seal kit includes!2,!3,!4. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g)

90 Compact Cylinder: Rod Double cting, Single Rod Series CQ2K ounting olt for CDQ2K/With uto Switch ounting method: ounting bolt for through-hole mounting of the CDQ2K is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x3 2 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated Head end mounting ounting bolt ounting bolt Rod end mounting Cylinder model CDQ2K-DCZ -DCZ -1DCZ -DCZ -2DCZ -3DCZ CDQ2K-DZ -DZ -1DZ -DZ -2DZ -3DZ CDQ2K-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ CDQ2K2-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ CDQ2K-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ C D ounting bolt part no. C' D' ounting bolt part no. Cylinder model C D ounting bolt part no. C' D' 3 CQ-3 x 3 x 4 CQ-3 x x 4 CDQ2K-DZ -4DZ CQ- x x. 4 x 4 x -DZ. x. x x -DZ x 4 x x CQ-3 x x 4 4 x x CQ-3 x 4 x -DZ CDQ2K-DZ -DZ -1DZ 4 x CQ- x 4 x x 4 x x -DZ x x x -2DZ x x x -3DZ x.. x x -3DZ x 4 CQ- x x 4 x x 4 CQ- x 4 x x x -DZ -4DZ -DZ -DZ x x x x. x x -DZ 1 x 1 1. x x CDQ2K-DZ CQ- x 4 x x x x CQ- x x 4 x x 4 x x x x CQ- x 4 x x x -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ. x x x x x x x x.. x x -DZ x. x x -DZ x x x x x CQ- x x x x x x x CQ- x x x CDQ2K-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ. CQ- x x x x x x x.. x x x x x x x x -4DZ -DZ -DZ -DZ 1 x x x x 1 1 ounting bolt part no. CQ- x x x x x CQ- x 4 x x x x x x x x x x x 1 CQ- x x x x x x x x x x x CQ- x x x x x x x x x x x 1 arge ore ong Stroke ade to Order Rod xial Piping nti-lateral oad With nd ock Water Resistant uto Switch With uto Switch 4

91 Series CQ2K Dimensions ø to ø2/without uto Switch (Through-hole): CQ2K ø, ø ø. ø, ø2. ø (ød) (K) H thread effective depth C 2 x øn through ød Q F 2 x x. (Port size) K øth Piston rod cross section øi G + Stroke + Stroke With boss on head end Width across flat 1 øth G With oss on Head nd 2 2 G C1 1 Th 1 1 H Rod nd ale Thread x. x 1. x 1.2 x H1 C1 1 Stroke range C D F G 2 to 3 to 3 to to For details about the rod end nut and accessory brackets, refer to page 1. H 3 x. 4 x. x. x 1. I K N Q. 1 1 Th

92 K Dimensions ø to ø2/with uto Switch Compact Cylinder: Rod Double cting, Single Rod Series CQ2K (Through-hole): CDQ2K ø, ø H thread effective depth C 2 x øn through. 3. ø. ød K U S ø, ø2 1 arge ore V ø ø ong Stroke H thread effective depth C 2 x øn through ød 2 x x. (Port size) Rod (ød) (K) Piston rod cross section U S V øth ø to ø2 With boss on head end Q G + Stroke + Stroke F øth xial Piping nti-lateral oad With nd ock G Width across flat 1 Water Resistant For auto switch proper mounting position and its mounting height, refer to pages to 1. 2 Stroke range to 3 to 3 to to C D F.... For details about the rod end nut and accessory brackets, refer to page 1. G H1 C1 1 H 3 x. 4 x. x. x 1. K N Q S Rod nd ale Thread Th U C1 1 H1 4 V x. x 1. x 1.2 x With uto Switch uto Switch ade to Order

93 Series CQ2K Dimensions ø/ Without uto Switch ø x 1.2 thread effective depth 2 x ø. through 2 x Rc, NPT, G 1/ (2 x x.) Note 1) 1. (.) Note 1) (Port size). (.) Note 1) (ø) ø x ø () ø21.2 Piston rod cross section + Stroke + Stroke Note 1) ( ): Stroke mm Stroke range to, With boss on head end ø21.2 Width across flat uilt-in one-touch fittings: ø 2 x ø (Piping tube O.D.) Note 2) The dimensions of the ø- mm stroke with built-in one-touch fittings are the same as those of the mm stroke cylinder tube. For details about the rod end nut and accessory brackets, refer to page 1.

94 Dimensions Compact Cylinder: Rod Double cting, Single Rod Series CQ2K ø/ With uto Switch. ø x 1.2 thread effective depth 2 x ø. through 1. 2 x Rc, NPT, G 1/ (Port size) uto switch inimum lead wire bending radius. arge ore (ø) () ø ø Stroke 4 + Stroke.2 ø21.2 Piston rod cross section Rod With boss on head end xial Piping Width across flat x 1. ø21 nti-lateral oad With nd ock uilt-in one-touch fittings: ø 2 x ø (Piping tube O.D.) uto Switch Water Resistant With uto Switch ong Stroke For details about the rod end nut and accessory brackets, refer to page 1. ade to Order

95 Series CQ2K Dimensions ø to ø/with uto Switch (Through-hole): CDQ2K (In the case of without auto switches, the and dimensions will be only changed. Refer to the dimension table.) oth ends tapped: CDQ2K O1 thread R R oth nds Tapped O1 x 1. x 1.2 x 1. R 1 H thread effective depth C 4 x øn through-hole x øo counterbore 2 x P (Port size) Q uto switch inimum lead wire bending radius F (ød) (K) Piston rod cross section K ød W Z J øth K 2 + Stroke + Stroke With boss on head end øth 2 With oss on Head nd Th H1 C1 1 Rod nd ale Thread C H x 1. 1 x 1. 1 x Cylinder tube form ø uilt-in one-touch fittings: ø to ø W1 V øz1 2 x P1 (Piping tube O.D.) uilt-in One-touch Fittings Z1 P1 V.. W1. 2 Stroke range to, to, to, Without auto switch With auto switch C For details about the rod end nut and accessory brackets, refer to page D 2 4 F.. H x 1.2 x 1. x 1. J K 1 1 N O. depth. depth depth. P 1/ 1/4 1/4 Q Th W Z

96 Compact Cylinder: Rod Double cting, Single Rod Series CQ2K Foot: CDQ2K Z H Y 4 x ød + Stroke Y Stroke Y Special cap bolt G S + Stroke Foot Stroke range to, to, to, G H Y Without auto switch With auto switch S S Z Y.2 1 D arge ore Rod flange: CDQ2KF F FZ FV 4 x øfd 1 FT + Stroke + Stroke 1 Rod Flange Stroke range Without auto switch With auto switch to 4. 2.,. 3. to 4. 3.,.. to 4 3, Foot bracket material: Carbon steel Surface treatment: Nickel plated FD FT FV F FZ ong Stroke Rod xial Piping 1 Head flange: CDQ2KG Flange bracket material: Carbon steel Surface treatment: Nickel plated nti-lateral oad Stroke + Stroke CT + Stroke C + Stroke + Stroke CW FT Double clevis: CDQ2KD FV 4 x N Cap bolt øcd hole H xis d CU RR F FZ C CZ x øfd For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. Head Flange Stroke range Without auto switch With auto switch 1 to 44., 4. to 4.,. to 3, Flange bracket material: Carbon steel Surface treatment: Nickel plated Double Clevis Stroke range Without auto switch With auto switch C C to to to ,,, CW 2 3 C 1 CZ N x 1. x 1.2 x 1. RR Double clevis bracket material: Cast iron Surface treatment: Painted The dimensions except, and 1 are the same as those of the rod flange. CD CT CU With nd ock Water Resistant With uto Switch uto Switch ade to Order

97 1

98 Without auto switch ø to ø2 Without auto switch ø to ø With auto switch F With auto switch (uilt-in magnet) ounting Through-hole () ø to ø oth ends tapped Foot ø to ø Flange ounting brackets are shipped together (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to ounting olt for C(D)Q2KW on pages and. uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2KW-3DZ Compact Cylinder: Rod Double cting, Double Rod Series CQ2KW ø, ø, ø, ø2, ø, ø, ø, ø CQ2KW CQ2KW CDQ2KW 2 Nil TN TF F mm mm mm 2 mm mm mm mm mm How to Order Port thread type thread ø to ø2 Rc NPT ø to ø G uilt-in one-touch fittings Note) Note) s available with one-touch fittings are ø to ø. For cylinders without auto switch, threads are compatible only for ø- mm stroke model. Cylinder stroke Refer to the next page for standard strokes. 3 D 3 D 3 D NV PV V NWV PWV WV NV PV V V 3V V N P NW PW W N P P3DW 3 Z Z W uto switch mounting groove Z ø to ø2 ø to ø Number of auto switches Nil S n 2 pcs. 1 pc. n pcs. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. 2 surfaces 4 surfaces ody option Nil (Rod end female thread) With rubber bumper C (ø with auto switch only) ction D Double acting Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. pplicable uto Switches/ Refer to the individual catalog (S-1) for the D-P3DW type. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) agnetic field resistant (2-color indication) lectrical entry Grommet Grommet Indicator light Wiring (Output) Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ Yes Yes No 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 2-wire (Non-polar) 3-wire (NPN equivalent) 2-wire oad voltage There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2. DC C 24 V V, V V V, V V V, V V V V V 24 V V, V V or less uto switch model Perpendicular In-line ead wire length (m). (Nil) 1 () 3 () None (Z) (N) Pre-wired connector Solid state auto switches marked with are produced upon receipt of order. The D-P3DW type is available from ø to ø only. pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC 2 arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

99 Series CQ2KW Specifications Symbol rod, Double acting ade to Order (For details, refer to pages 1 to.) Symbol Specifications - Intermediate stroke (xclusive body type) Intermediate stroke of double rod cylinder, -3 ø to ø only -3: Intermediate stroke in mm intervals only 2 ction Fluid Proof pressure aximum operating pressure inimum operating pressure. Pa Double acting, Double rod ir 1. Pa 1. Pa. Pa mbient and fluid temperature Without auto switch: to C (No freezing) With auto switch: to C (No freezing) ubrication Piston speed llowable kinetic energy (J) Stroke length tolerance Rod non-rotating accuracy Not required (Non-lube) to mm/s..43 Note 1) mm Note 2) ±2 ±1 ±. ø with auto switch: With rubber bumper () Note 1) For cylinders with rubber bumper (ø with auto switch only) Note 2) Stroke length tolerance does not include the amount of bumper change. Strokes,, 2,, Type Part no. Description Stroke range xample stroke,, 1,, 2, 3,, 1,, 2, 3, 3,, 4,,, 1,, 2, 3, 3,, 4,,,, 1,, 2, 3, 3,, 4,,, anufacture of Intermediate Strokes.4. spacer is installed in the standard stroke body. Refer to How to Order for the standard model number. (P. 2) Strokes in mm intervals are available by installing a spacer in the standard stroke cylinder. to Part no.: CQ2KW-DZ CQ2KW-DZ with mm width spacer inside The dimension is. mm. Stroke range to Type 3 Pneumatic 2 Through-hole () ounting oth ends tapped uilt-in magnet x. x. x. x. Piping Pipe thread TN TF uilt-in one-touch fittings Note 1) x. Rc1/ NPT1/ NPT1/ NPT1/4 NPT1/4 G1/ G1/ G1/4 G1/4 ø/4 Note 2) Rc1/ ø/4 Rc1/4 Refer to pages to 1 for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. ø/ Rc1/4 Note 1) ø without auto switch: x. is used for mm stroke piping dimension. Thus, do not enter a symbol for the port thread type. Note 2) The dimensions of the ø- mm stroke with built-in one-touch fittings are the same as those of the mm stroke cylinder tube. ø/

100 Compact Cylinder: Rod Double cting, Double Rod Series CQ2KW Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. ounting Warning 1. Do not apply reverse torque to the piston rods sticking out from both sides of this cylinder at the same time. The torque makes connection threads inside loosen, which may cause an accident or malfunction. Install or remove loads while the piston rod width across flat is secured. lso, tighten by giving consideration to prevent the tightening torque from being applied to the nonrotating guide. Do not fix the other side of the piston rod width across flat and apply reverse torque. 2. Using a non-rotating rod cylinder void using the air cylinder in such a way that rotational torque would be applied to the piston rod. If rotational torque is applied, the non-rotating guide will deform, causing a loss of non-rotating accuracy. Use the below table as a guide for the allowable rotational torque ranges. llowable rotational torque N m or less ø ø ø ø2 ø ø ø ø ounting rackets/part No. 2 Foot Note 1) Flange CQ- CQ- CQ CQ-F CQ-F CQ-F Note 1) When ordering a foot bracket, order 2 pieces per cylinder. Note 2) Parts belonging to each bracket are as follows. Foot or Flange: ody mounting bolts Weight Weight dditional Weight oth ends tapped uilt-in one-touch fittings Foot Flange ale thread Nut Calculation: (xample) CQ2KW-DZ asic weight: CQ2KW-DZ 424 g dditional weight: oth ends tapped g g 1 g Theoretical Output Cylinder stroke (N) Operating pressure (Pa) (g) (g) arge ore ade to Order ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant uto Switch With uto Switch 4

101 Series CQ2KW Construction (ø to ø) (ø to ø) uilt-in one-touch fittings Component Parts No Description Cylinder tube Piston Piston rod Piston rod Rod cover Collar for non-rotating Collar Retaining ring ushing for non-rotating ushing Hexagon socket head cap screw Hexagon socket head set screw Rod end nut One-touch fitting Piston seal Rod seal for non-rotating Rod seal Gasket Piston gasket aterial luminum alloy luminum alloy Stainless steel Carbon steel Stainless steel Carbon steel rass luminum alloy luminum alloy luminum alloy luminum alloy casted Carbon tool steel Oil-impregnated sintered alloy earing alloy lloy steel lloy steel Carbon steel NR NR NR NR NR Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø2 ø to ø, Hard chrome plated ø, lectroless nickel plated ø to ø, nodized ø to ø, nodized ø to ø, nodized ø to ø, Chromated, Painted Phosphate coated ø to ø ø, ø ø to ø, Nickel plated ø to ø, Nickel plated Nickel plated ø to ø ø to ø Replacement Parts/Seal Kit 2 Kit no. CQ2KW-PS CQ2KW-PS CQ2KW-PS CQ2KW2-PS CQ2KW-PS CQ2KW-PS CQ2KW-PS CQ2KW-PS Contents Kits include items!,!,!,! from the table. Seal kit includes!,!,!,!. Order the seal kit based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g)

102 Compact Cylinder: Rod Double cting, Double Rod Series CQ2KW ounting olt for CQ2KW/Without uto Switch ounting method: ounting bolt for through-hole mounting of the CQ2KW is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x 2 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt rod end mounting ounting bolt Cylinder model C D ounting bolt part no. C' D' ounting bolt part no. Cylinder model C D CQ2KW-D -D 4 CQ-3 x x 4 4 CQ-3 x x 4 CQ2KW-DZ -DZ 4-1D.3 x.3 x -1DZ -D x x -DZ -2D x x -2DZ -3D x x -3DZ CQ2KW-D CQ-3 x CQ-3 x -3DZ -D 4 x 4 4 x 4 -DZ -1D x x -4DZ.. -D x x -DZ -2D -3D CQ2KW-D -D -1D -D 4 x x CQ- x x 4 x x 4 x x CQ- x x 4 x x -DZ -DZ CQ2KW-DZ -1DZ -DZ -2DZ 1-2D x x -3DZ. -3D x x -3DZ. -3D -D -4D -D CQ2KW2-D -D -1D -D 4 x x x x CQ- x 4 x x x 4 x x x x CQ- x 4 x x x -DZ -4DZ -DZ -DZ -DZ CQ2KW-DZ -1DZ -DZ 1-2D x x -2DZ. -3D x x -3DZ -3D -D -4D -D CQ2KW-DZ -DZ -1DZ -DZ -2DZ x x x x CQ- x x x x x 4 x x x x CQ- x 4 x x x x -3DZ -DZ -4DZ -DZ -DZ -DZ. 1-3DZ x x. -3DZ x x -DZ -4DZ -DZ -DZ -DZ 1 x x x x x 1 1 x x x x x 1 Copper and Fluorine-free Series (For CRT anufacturing Process) ounting bolt part no. CQ- x 4 x x x x x x x x x x x 1 CQ- x x x x x x x x x x x 1 CQ- x x x x x x x x x x x 1 ø to ø: The C, and D, dimensions are the same as those of C and D. arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch CQ2KW Stroke D()(Z) Copper and fluorine-free series ø, ø, ø2, ø, ø, ø, ø For preventing the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. Specifications ction Proof pressure ax. operating pressure Rubber bumper Piping Piston speed ounting uto switch 2 Double acting, Double rod 1. Pa 1. Pa None Pipe thread to mm/s Through-hole ountable uto Switch ade to Order

103 Rod: Double cting, Double Rod Series CDQ2KW With uto Switch Refer to the below pages for further information on auto switches. uto switch proper mounting position and its mounting height inimum stroke for auto switch mounting P. to 1 Operating range uto switch mounting brackets/part no. Weight Weight 2 (g) Cylinder stroke dditional Weight oth ends tapped Rod end male thread ale thread Nut uilt-in one-touch fittings Calculation: (xample) CDQ2KW-DZ asic weight: CDQ2KW-DZ 3 g dditional weight: oth ends tapped g g 24 g dd each weight of auto switches when auto switches are mounted (g) Construction ø to ø2 ø ø to ø Component Parts No Description Cylinder tube Piston Piston rod Piston rod Rod cover Collar for non-rotating Collar Retaining ring ushing for non-rotating ushing Hexagon socket head cap screw Hexagon socket head cap screw Hexagon socket head set screw agnet aterial luminum alloy luminum alloy Stainless steel Carbon steel Stainless steel Carbon steel rass luminum alloy luminum alloy luminum alloy luminum alloy casted Carbon tool steel Oil-impregnated sintered alloy earing alloy lloy steel lloy steel lloy steel Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø2 ø to ø, Hard chrome plated ø, lectroless nickel plated ø to ø, nodized ø to ø, nodized ø to ø, nodized ø to ø, Chromated, Painted Phosphate coated ø to ø ø, ø ø to ø2, Nickel plated ø, Nickel plated ø to ø, Nickel plated No Description Piston seal Rod seal for non-rotating Rod seal Gasket Piston gasket aterial NR NR NR NR NR Replacement Parts/Seal Kit 2 Kit no. CQ2KW-PS CQ2KW-PS CQ2KW-PS CQ2KW2-PS CQ2KW-PS CQ2KW-PS CQ2KW-PS CQ2KW-PS Note ø to ø Contents Kits include items!,!,!,! from the table. Seal kit includes!,!,!,!. Order the seal kit based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g)

104 Compact Cylinder: Rod Double cting, Double Rod Series CQ2KW ounting olt for CDQ2KW/With uto Switch ounting method: ounting bolt for through-hole mounting of the CDQ2KW is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x 2 pcs. ounting bolt rod end mounting ounting bolt aterial: Chromium molybdenum steel Surface treatment: Nickel plated Cylinder model C D CDQ2KW-DCZ -DCZ 4-1DCZ.1 -DCZ -2DCZ -3DCZ CDQ2KW-DZ -DZ 4-1DZ. -DZ -2DZ -3DZ CDQ2KW-DZ -DZ -1DZ -DZ 4-2DZ -3DZ -3DZ -DZ -4DZ -DZ CDQ2KW2-DZ -DZ -1DZ -DZ 4-2DZ -3DZ -3DZ -DZ -4DZ -DZ CDQ2KW-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ -DZ 1 ounting bolt part no. CQ-3 x x 4 x x x x CQ-3 x 4 x x x x x CQ- x 4 x x x x x x x x x CQ- x 4 x x x x x x x x x CQ- x x x x x x x x x x x x 1 C'.1.. D' 4 1 ounting bolt part no. CQ-3 x 4 x x x x x CQ-3 x x x x x x CQ- x x x x x x x x x x CQ- x x x x x x x x x x CQ- x x x x x x x x x x x x 1 Cylinder model C D CDQ2KW-DZ -DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ -DZ CDQ2KW-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ -DZ CDQ2KW-DZ -1DZ -DZ -2DZ -3DZ -3DZ -DZ -4DZ -DZ -DZ -DZ ounting bolt part no. CQ- x x x x x x x x x x x x 1 CQ- x x x x x x x x x x x 1 CQ- x x x x x x x x x x x 1 ø to ø: The C, and D, dimensions are the same as those of C and D. arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

105 Series CQ2KW Dimensions ø to ø/without uto Switch (Through-hole): CQ2KW ø to ø2 ø, ø ø, ø ø. ø 2 x H thread effective depth C (lso back cover) (ød) (K1) 2 x øn through ød Q F 2 x P (Port size) ød K1 Piston rod cross section øi øth G + Stroke + 2 (Stroke) Width across flat K2 + Stroke ø. ø 2 x H thread effective depth C (lso back cover) 2 x øn through Q 2 x P (Rc, NPT, G) (Port size) F Width across flat K2 (ød) (K1) Piston rod cross section ød W Z J uilt-in one-touch fittings: ø øth 1 H1 K1 C1 1 G + Stroke + 2 (Stroke) (Stroke) ød 1 + Stroke + Stroke 1 H1 C1 Rod nd ale Thread 2 2 Stroke range to 3 to 3 to to to, x. x 1. x 1.2 x 1.2 x 1. C H uilt-in one-touch fittings 2 x ø (Piping tube O.D.) ø 2 Stroke range to 3 to 3 to to to, C D F.. G H 3 x. 4 x. x. x 1. x 1.2 I J 4. K1.2 K The dimensions of ø- mm stroke with builtin one-touch fittings are the same as those of the mm stroke cylinder tube N P Q x. 1 x. 1 x. 1. x. 1 x / Th W 4. Z For details about the rod end nut and accessory brackets, refer to page 1. Note) The positions of piston rod s width across flats (K2) are not constant.

106 Dimensions ø to ø/with uto Switch (Through-hole): CDQ2KW (ød) (K1) K1 Piston rod cross section U S V ø H thread effective depth C (lso back cover) 2 x øn through ød 2 x H thread effective depth C (lso back cover) 2 x øn through ød Compact Cylinder: Rod Double cting, Double Rod øth. ø, ø ø, ø2 3. Q F G + Stroke + 2 (Stroke) ø. 2 x P (Port size) ød + Stroke 1 Width across flat K2 Series CQ2KW ø arge ore ong Stroke K1 U S ø. ø Rod ø (ød) ø to ø2 2 x H thread effective depth C (lso back cover) (K1) Piston rod cross section ød V W 2 x øn through Z J øth 1 K1 G Q F + Stroke + 2 (Stroke) uto switch inimum lead wire bending radius 2 x P (Rc, NPT, G) (Port size) Width across flat K2 ød + Stroke 1 Rod nd ale Thread C1 1. x. x 1. x 1.2 x 1.2 x 1. H xial Piping nti-lateral oad With nd ock uilt-in one-touch fittings: ø 3. ø H1 C1 1 uilt-in one-touch fittings (Stroke) 2 x ø (Piping tube O.D.) H1 C1 1 + Stroke Water Resistant With uto Switch For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke range C D F G H J K1 K2 to x to x to x to x 1. to,, x For details about the rod end nut and accessory brackets, refer to page 1. Note) The positions of piston rod s width across flats (K2) are not constant. N P x. x. x. x. 1/ Q S Th U V W Z 4. uto Switch ade to Order

107 Series CQ2KW Dimensions ø to ø/with uto Switch (In the case of without auto switches, the, dimensions will be only changed. Refer to the dimension table.) (Through-hole): CQ2KW/CDQ2KW 2 x H thread effective depth C (lso back cover) (ød) (K1) Piston rod cross section ød 4 x øn through x øo counterbore Z O1 thread øth K1 2 J W oth ends tapped: CQ2KW/CDQ2KW R 2 x P (Port size) Q + Stroke R + 2 (Stroke) uto switch inimum lead wire bending radius Q Width across flat K2 ød + Stroke oth nds Tapped O1 x 1. x 1.2 x 1. R H1 H1 C1 C (Stroke) 1+ Stroke Rod nd ale Thread Without auto switch With auto switch C H x 1. 1 x 1. 1 x Cylinder tube form ø uilt-in one-touch fittings: ø to ø V øz1 2 x P1 (Piping tube O.D.) uilt-in One-touch Fittings Z1 P1 V.. W1. 2 W1 For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke range Without auto switch With auto switch C D H J K1 K2 N to to to ,,, x 1.2 x 1. x For details about the rod end nut and accessory brackets, refer to page 1. Note) The positions of piston rod s width across flats (K2) are not constant. O depth depth depth. P 1/ 1/4 1/4 Q 1. Th W 1 4 Z

108 Compact Cylinder: Rod Double cting, Double Rod Series CQ2KW Foot: CQ2KW/CDQ2KW + Stroke + Stroke Z H Y 4 x ød Special cap bolt Y T Y + 2 (Stroke) G S + Stroke arge ore Rod nd ale Thread Without auto switch With auto switch ong Stroke Foot (Stroke) 1 + Stroke Rod Stroke range to, to, Without auto switch With auto switch S S D. G 4 H 33 3 T Y Z.2. Y xial Piping to, Flange: CQ2KWF/CDQ2KWF Foot bracket material: Carbon steel Surface treatment: Nickel plated nti-lateral oad F FZ FV 4 x øfd 1 FT + Stroke + 2 (Stroke) 2 + Stroke Rod nd ale Thread Without auto switch With auto switch With nd ock Water Resistant (Stroke) 4 + Stroke With uto Switch Flange For auto switch proper mounting position and its mounting height, refer to pages to 1. Stroke range Without auto switch With auto switch FD FT FV F FZ 1 2 to to to ,,, For details about the rod end nut and accessory brackets, refer to page 1. Flange bracket material: Carbon steel Surface treatment: Nickel plated uto Switch ade to Order 2

109 Without auto switch With auto switch With auto switch (uilt-in magnet) xial piping ounting Through-hole Cylinder mounting bolts are not included. Order them separately referring to ounting olt for C(D)QP2 on pages and. Nil H Compact Cylinder: xial Piping Double cting, Single Rod Series CQP2 ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø CQP2 CDQP2 Type Pneumatic Note 1) ir-hydro Note 1) s available for airhydro type are ø to ø. uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQP2-3D Nil TN TF 2 mm mm mm 2 mm mm mm mm mm mm mm thread Rc NPT G How to Order 3 D Port thread type ø to ø2 ø to ø 3 D W ction D Double acting ade to Order Refer to the next page for details. Number of auto switches Nil S n 2 pcs. 1 pc. n pcs. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. ody option Nil C Cylinder stroke Refer to the next page for standard strokes. (Rod end female thread) With rubber bumper Note 2) Combination of body option ( C ) is available. Note 2) ir-hydro type with rubber bumper is not available. pplicable uto Switches/Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) agnetic field resistant (2-color indication) lectrical entry Grommet Connector Grommet Indicator light Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 4-wire 2-wire (Non-polar) 3-wire (NPN equivalent) oad voltage DC V, V C 24 V V V, V V V, V V V, V uto switch model Perpendicular NV PV V JC NWV PWV WV NV PV V In-line N P NW PW W N P FF P4DW V V Yes Grommet V 2 2H V V 3V 3 No V, V V or less V 2-wire Yes 24 V V 3C Connector No V, V 24 V or less C Diagnostic indication (2-color indication) Grommet Yes W Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ None N (xample) JCN There are other applicable auto switches other than the listed above. For details, refer to page. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No ead wire length (m). (Nil) 1 () 3 () None (Z) (N) Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit Solid state auto switches marked with are produced upon receipt of order. The D-P4DW type is available from ø to ø only. Only for the D-P4DW type, an auto switch is assembled and shipped with the cylinder. Relay, PC Relay, PC

110 Compact Cylinder: xial Piping Double cting, Single Rod Series CQP2 Specifications Pneumatic type 2 ction Fluid Proof pressure Double acting, Single rod ir 1. Pa Rod end male thread aximum operating pressure inimum operating pressure mbient and fluid temperature ubrication 1. Pa. Pa. Pa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Not required (Non-lube) arge ore Piston speed to mm/s JIS Symbol Double acting, Single rod llowable kinetic Without cushion energy (J) With rubber bumper mm Note) Stroke length tolerance Note) Stroke length tolerance does not include the amount of bumper change ong Stroke ade to Order (For details, refer to pages 1 to.) Symbol Specifications - Special rod end shape - Heat resistant cylinder ( to 1 C) w/o auto switch only - Cold resistant cylinder ( to C) w/o auto switch only - ow-speed cylinder ( to mm/s) - ow-speed cylinder ( to mm/s) -C4 With heavy-duty scraper, ø to ø only Piston rod/retaining ring/rod end nut -C material: Stainless steel -C3 With coil scraper -C3 With boss on rod end -21 Fluororubber seals Refer to pages 3 to for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. ir-hydro type 2 ction Fluid Proof pressure aximum operating pressure inimum operating pressure mbient and fluid temperature Piston speed Cushion.1 Pa Double acting, Single rod Turbine oil Note) 1. Pa 1. Pa.1 Pa to C to mm/s None +1. mm Stroke length tolerance Note) Refer to Handling Precautions for SC Products (-3-3) for ctuator Precautions (). Strokes Pneumatic type (Non-lube) ir-hydro type stroke,,, 1,, 2, 3,, 1,, 2, 3, 3, 2, 4,,, 1,, 2, 3, 3, 2, 4,,, 1,, 2, 3, 3,, 4,,,,, 1,, 2, 3, 3,, 4,,,,, 1,, 2, 3, 3,,,, 1,, 2, 3, 3, 4,,,, 4,,, anufacture of Intermediate Strokes Type Part no. Description Stroke range xample spacer is installed in the standard stroke body. Refer to How to Order for the standard model number. (P. 3) Strokes in 1 mm intervals are available by installing a spacer in the standard stroke cylinder.,, 2 to Part no.: CQP2-D CQP2-D with 1 mm width spacer inside The dimension is. mm. Stroke range 1 to 2 1 to 4 1 to xcept air-hydro type In the case of spacer type, intermediate strokes with bumper for ø to ø, it can be manufactured in mm intervals in mm and to mm. 4 Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

111 Series CQP2 Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. Type Pneumatic ir-hydro ounting Through-hole () uilt-in magnet Piping With rubber bumper ounting Through-hole () uilt-in magnet Piping Pipe thread Pipe thread 2 x. x. x. x. Rc1/ NPT1/ G1/ Rc1/ NPT1/ G1/ Rc1/4 NPT1/4 G1/4 Rc1/4 NPT1/4 G1/4 Rc3/ NPT3/ G3/ Rc3/ NPT3/ G3/ x. x. Rc1/ Rc1/ Rc1/4 Rc1/4 Rc3/ Rc3/ ounting/removal 1. Do not remove the hexagon socket set screw on the side of the rod. e aware that if the hexagon socket set screw is removed with compressed air supplied to the cylinder, an internal steel ball could fly out or the compressed air could be discharged, leading to injury to humans or damage to peripheral equipment. Theoretical Output 2 Operating direction IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT OUT IN Operating pressure (Pa) (N) Weight Weight Cylinder stroke (g) dditional Weight Rod end male thread ale thread Nut With rubber bumper 2 Calculation: (xample) CQP2-DC asic weight: CQP2-D dditional weight: With rubber bumper 2 g 43 g 3 g g (g) 1 1

112 Compact Cylinder: xial Piping Double cting, Single Rod Series CQP2 ounting olt for CQP2/Without uto Switch ounting method: ounting bolt for through-hole mounting of the CQP2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. aterial: Chromium molybdenum steel xample) CQ-3x2 2 pcs. Surface treatment: Nickel plated ounting bolt Cylinder model CQP2-D -D -1D -D -2D -3D CQP2-D -D -1D -D -2D -3D CQP2-D -D -1D -D -2D -3D -3D -D -4D -D CQP-D -D -1D -D -2D -3D -3D -D -4D -D C... D ounting bolt part no. CQ-3 x 2 x 3 x 3 x x 4 x CQ-3 x 2 x 3 x 3 x x 4 x CQ- x 2 x 3 x 3 x x 4 x x x x x CQ- x 3 x 3 x x 4 x x x x x x Cylinder model CQP2-D -D -1D -D -2D -3D -3D -D -4D -D -D -D CQP2-D -D -1D -D -2D -3D -3D -D -4D -D -D -D CQP2-D -1D -D -2D -3D -3D -D -4D -D -D -D C.. D ounting bolt part no. CQ- x 3 x 3 x x 4 x x x x x x x 1 x CQ- x 3 x x 4 x x x x x x x x x 1 CQ- x 4 x x x x x x x x x x Cylinder model C CQP2-D -1D -D -2D -3D -3D. -D -4D -D -D -D CQP2-D -1D -D -2D -3D -3D 1 -D -4D -D -D -D CQP2-D -1D -D -2D -3D -3D 1. -D -4D -D -D -D D ounting bolt part no. CQ- x x x x x x x x x x x 1 CQ- x x x x x x x x x x x 1 CQ- x x x x x x x x x x 1 x arge ore ade to Order ong Stroke Rod uto Switch xial Piping nti-lateral oad With nd ock With uto Switch Water Resistant

113 Series CQP2 Construction - section (Port on rod end) - section (Port on head end) With rubber bumper Component Parts No Description Cylinder tube Piston Piston rod Collar Retaining ring ushing Rod end nut umper umper Steel ball Hexagon socket head set screw Piston seal Rod seal Gasket aterial luminum alloy luminum alloy Stainless steel Carbon steel luminum alloy luminum alloy casted Carbon tool steel earing alloy Carbon steel Urethane Urethane Carbon steel lloy steel NR NR NR Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø, nodized ø to ø, Chromated, Painted Phosphate coated ø to ø Nickel plated Nickel plated Replacement Parts/Seal Kit 2 Pneumatic type (Non-lube) CQ2-PS CQ2-PS CQ2-PS CQ-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS Kit no. ir-hydro type CQ2H-PS CQ2H2-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS Contents Kits include items!2,!3,!4 from the table. Seal kit includes!2,!3,!4. Order the seal kit based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) Copper and Fluorine-free Series (For CRT anufacturing Process) CQP2 Stroke D Copper and fluorine-free series ø, ø, ø, ø2, ø ø, ø, ø, ø, ø For preventing the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. Specifications ction Proof pressure ax. operating pressure Rubber bumper Piping Piston speed ounting uto switch 2 Double acting, Single rod 1. Pa 1. Pa None Pipe thread to mm/s Through-hole ountable

114 xial Piping: Double cting, Single Rod Series CDQP2 With uto Switch Refer to the below pages for further information on auto switches. uto switch proper mounting position and its mountig height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. P.3 to Weight arge ore dditional Weight Rod end ale thread male thread Nut With rubber bumper Rod end ale thread male thread Nut With rubber bumper (g) Weight ore size Cylinder stroke (g) Calculation: (xample) CDQP2-DC asic weight: CDQP2-D 2 g dditional weight: 43 g With rubber bumper 3 g 33 g dd each weight of auto switches when auto switches are mounted. uto Switch ounting racket/weight 1 ounting bracket part no. pplicable bore size Weight (g) Q-1 ø to ø Q-2 Q2- ø to ø ø to ø 1. ong Stroke Rod xial Piping Construction nti-lateral oad With nd ock uto switch Water Resistant - section (Port on rod end) - section (Port on head end) Component Parts No Description Cylinder tube Piston Piston rod Collar Retaining ring ushing agnet Steel ball Hexagon socket head set screw Piston seal Rod seal Gasket aterial luminum alloy luminum alloy Stainless steel Carbon steel luminum alloy luminum alloy casted Carbon tool steel earing alloy Carbon steel lloy steel NR NR NR Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø, nodized ø to ø, Chromated, Painted Phosphate coated ø to ø Nickel plated Replacement Parts/Seal Kit 2 Pneumatic type (Non-lube) CQ2-PS CQ2-PS CQ2-PS CQ-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS Kit no. ir-hydro type CQ2H-PS CQ2H2-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS CQ2H-PS Contents Kits include items!,!1,!2 from the table. Seal kit includes!,!1,!2. Order the seal kit based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) With uto Switch uto Switch ade to Order

115 Series CQP2 ounting olt for CDQP2/With uto Switch ounting method: ounting bolt for through-hole mounting of the CDQP2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x3 2 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt Cylinder model CDQP2-D -D -1D -D -2D -3D CDQP2-D -D -1D -D -2D -3D CDQP2-D -D -1D -D -2D -3D -3D -D -4D -D CDQP-D -D -1D -D -2D -3D -3D -D -4D -D C... D ounting bolt part no. CQ-3 x 3 x x 4 x x x CQ-3 x x 4 x x x x CQ- x x 4 x x x x x x x x CQ- x x 4 x x x x x x x x Cylinder model CDQP2-D -D -1D -D -2D -3D -3D -D -4D -D -D -D CDQP2-D -D -1D -D -2D -3D -3D -D -4D -D -D -D CDQP2-D -1D -D -2D -3D -3D -D -4D -D -D -D C.. D ounting bolt part no. CQ- x x 4 x x x x x x x x x 1 x CQ- x 4 x x x x x x x x x x x 1 CQ- x x x x x x x x x x x Cylinder model C CDQP2-D -1D -D -2D -3D -3D. -D -4D -D -D -D CDQP2-D -1D -D -2D -3D -3D 1 -D -4D -D -D -D CDQP2-D -1D -D -2D -3D -3D 1. -D -4D -D -D -D D ounting bolt part no. CQ- x x x x x x x x x x x 1 CQ- x x x x x x x x x x x 1 CQ- x x x x x x x x 1 x x 1 x

116 Dimensions ø to ø/without uto Switch ø to ø2 H thread effective depth C ød Compact Cylinder: xial Piping Double cting, Single Rod øi.3 2 W Series CQP2 Width across flat 1 2 ø to ø H thread effective depth C K Plug Stroke range to 3 to 3 to to Plug H1 C C + Stroke + Stroke D x øn through 4 x øo counterbore F x øn through x øo counterbore H 3 x. 4 x. x. x 1. F 2 Z F x x. (Port size) Rod nd ale Thread I K C1 1 H N x P (Rc, NPT, G) (Port size) x. x 1. x 1.2 x 1.2 O. depth 3.. depth 3. depth depth. 1. W arge ore ød ong Stroke Rod xial Piping øi W Q J nti-lateral oad Width across flat 1 K Stroke range to, to, to, to, to, to, H1 C Stroke + Stroke C1 H x 1. x 1. 1 x 1. 1 x 1. x 1. 2 x 1. C D F H I J K N O P Q W Z x 1.2 x 1.2 x 1. x 1. x 2. x 2. Note) The external dimensions with rubber bumper are the same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page Rod nd ale Thread depth depth depth depth. 1. depth. 1. depth. 1/ 1/ 1/4 1/4 3/ 3/ With nd ock Water Resistant With uto Switch uto Switch ade to Order

117 Series CQP2 Dimensions ø to ø/with uto Switch ø to ø2 H thread effective depth C 2. uto switch inimum lead wire bending radius øi S ød W 2.3 K K H1 C1 1 F Z F 4. 1 øi S ød W Q J U 2 ø to ø H thread effective depth C Plug Width across flat 1 For auto switch proper mounting position and its mounting height, refer to pages 3 to. Stroke range to 3 to 3 to to C Plug D F Stroke + Stroke H 3 x. 4 x. x. x 1. Note) The external dimensions with rubber bumper are the same as those of the standard, as shown above. I x øn through 4 x øo counterbore Rod nd ale Thread 2 K x øn through x øo counterbore 2 3 C1 1 N H O. depth 3.. depth 3. depth depth 2 x x. (Port size) x. x 1. x 1.2 x 1.2 S U W x P (Rc, NPT, G) (Port size) U. 2 uto switch inimum lead wire bending radius + Stroke + Stroke Width across flat 1 For auto switch proper mounting position and its mounting height, refer to pages 3 to. Stroke range to to to to to to C D F H1 C1 1 H x 1.2 x 1.2 x 1. x 1. x 2. x 2. I 3 1 J. 1. K Rod nd ale Thread N... O depth depth depth depth. 1. depth. 1. depth. C P 1/ 1/ 1/4 1/4 3/ 3/ H1 Q S x 1. x 1. 1 x 1. 1 x 1. x 1. 2 x 1. Note) The external dimensions with rubber bumper are the same as those of the standard, as shown above. For details about the rod end nut and accessory brackets, refer to page 1. 1 U W Z

118 Without auto switch With auto switch ounting Through-hole With auto switch (uilt-in magnet) uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQP2-S Compact Cylinder: xial Piping Single cting, Single Rod Series CQP2 ø, ø, ø, ø2, ø, ø, ø CQP2 CDQP2 xial piping Cylinder mounting bolts are not included. Order them separately referring to ounting olt for C(D)QP2 on pages 1 and. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) lectrical entry Grommet Connector Grommet Nil TN TF Indicator light Yes 2 mm mm mm 2 mm mm mm mm Port thread type thread ø to ø2 Rc NPT ø to ø G Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 4-wire 3-wire (NPN equivalent) How to Order oad voltage DC C T T ction S T W Cylinder stroke Refer to the next page for standard strokes. NV PV V JC NWV PWV WV NV PV V ody option Nil N P NW PW W N P FF Nil S n uto switch Nil ade to Order Refer to the next page for details. Number of auto switches 2 pcs. 1 pc. n pcs. Without auto switch Refer to the below table for applicable auto switches. (Rod end female thread) Single acting, Spring return Single acting, Spring extend pplicable uto Switches/Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. 24 V V, V V V, V V V, V V V, V uto switch model Perpendicular In-line ead wire length (m). (Nil) 1 () 3 () None (Z) (N) V V Yes Grommet V 2 2H V V 3V 3 No V, V V or less V 2-wire Yes 24 V V 3C Connector No V, V 24 V or less C Diagnostic indication (2-color indication) Grommet Yes W Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW Solid state auto switches marked with are produced upon receipt of order. 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ None N (xample) JCN There are other applicable auto switches other than the listed above. For details, refer to page. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2. Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC 1 arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

119 Series CQP2 Specifications 2 ction Fluid Proof pressure aximum operating pressure inimum operating pressure (Pa) mbient and fluid temperature Double acting, Single rod ir 1. Pa 1. Pa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) ubrication Not required (Non-lube) JIS Symbol Single acting, Spring return Single acting, Spring extend Piston speed llowable kinetic energy (J) Stroke length tolerance to mm/s mm.4 Strokes ade to Order (For details, refer to pages 1 to.) Symbol Specifications - Special rod end shape Piston rod/retaining ring/rod end nut -C material: Stainless steel -C3 With boss on rod end -21 Fluororubber seals 2 stroke,, anufacture of Intermediate Strokes (xcept single acting, spring return) Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. Type Type Part no. Description Stroke range xample spacer is installed in the standard stroke body. Refer to How to Order for the standard model number. (P. 1) Strokes in 1 mm intervals are available by installing a spacer in the standard stroke cylinder. to Part no.: CQP2-3T CQP2-T with 2 mm width spacer inside The dimension is 24. mm. Stroke range 1 to 1 to 1 ounting/removal 1. Do not remove the hexagon socket set screw on the side of the rod. e aware that if the hexagon socket set screw is removed with compressed air supplied to the cylinder, an internal steel ball could fly out or the compressed air could be discharged, leading to injury to humans or damage to peripheral equipment. Pneumatic ounting Through-hole () uilt-in magnet Piping Pipe thread x. x. x. x. 2 Rc1/ NPT1/ G1/ Rc1/ NPT1/ G1/ Rc1/4 NPT1/4 G1/4 Refer to pages 3 to for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. 1

120 Compact Cylinder: xial Piping Single cting, Single Rod Series CQP2 Theoretical Output Weight ction Spring return Spring extend 2 2 (N) Operating pressure (Pa) Weight ction Spring return Spring extend Cylinder stroke (g) 1 arge ore ong Stroke ounting olt for CQP2/Without uto Switch ounting method: ounting bolt for through-hole mounting of the CQP2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x2 2 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated Spring Return Cylinder model CQP2-S -S CQP2-S -S CQP2-S -S CQP-S -S CQP2-S -S CQP2-S -S CQP2-S -S Spring xtend Cylinder model CQP2-T -T CQP2-T -T CQP2-T -T CQP-T -T CQP2-T -T CQP2-T -T CQP2-T -T C..... C..... D D ounting bolt ounting bolt part no. CQ-3 x 2 x 3 CQ-3 x 2 x 3 CQ- x 2 x 3 CQ- x 3 x 3 CQ- x 3 x 3 CQ- x 3 x CQ- x 4 x ounting bolt ounting bolt part no. CQ-3 x 2 x 3 CQ-3 x 2 x 3 CQ- x 2 x 3 CQ- x 3 x 3 CQ- x 3 x 3 CQ- x 3 x CQ- x 4 x dditional Weight 2 Rod end male thread ale thread Nut Calculation: (xample) CQP2-S asic weight: CQP2-S g dditional weight: 43 g 2 g Spring Force Single cting, Spring Return (N) Spring reaction force (N) 2 Stroke Stroke Second Second First Single cting, Spring xtend (N) Spring reaction force (N) 2 First Single acting, Spring return Spring state with first mounting load IN Spring state with first mounting load OUT (g) 3 When spring is set in cylinder Spring state with second mounting load OUT When spring is compressed with air Single acting, Spring extend When spring is set in cylinder Spring state with second mounting load IN When spring is compressed with air 1 Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

121 Series CQP2 Construction Spring return Port size x. Spring extend - section (Port on rod end) - section (Port on head end) - section (Port on rod end) - section (Port on head end) Component Parts No. Description 1 Cylinder tube 2 Piston 3 Piston rod aterial luminum alloy luminum alloy Stainless steel Carbon steel luminum alloy luminum alloy casted Carbon tool steel earing alloy Piano wire Sintered metallic C Carbon tool steel lloy steel Carbon steel lloy steel Note Hard anodized Chromated ø to ø2 ø to ø, Hard chrome plated ø to ø, nodized ø, Chromate, Painted Phosphate coated 4 Collar Retaining ring ushing Return spring Zinc chromated ronze element Port size Rc1/, 1/4 Retaining ring Plug with fixed orifice Port size x. Steel ball Hexagon socket head set screw Nickel plated Rod end nut Carbon steel Nickel plated On spring extend (Type T), piston and piston rod are integrated (stainless steel). No. 1 Description Piston seal Rod seal Gasket Replacement Parts/Seal Kit 2 Contents How to Order aterial NR NR NR Kit no. (Single acting/spring return) CQ2-S-PS CQ2-S-PS CQ2-S-PS CQ-S-PS CQ2-S-PS CQ2-S-PS CQ2-S-PS Kits include item!4 from the table. Seal kit includes!4. Order the seal kit, based on each bore size. Note Kit no. (Single acting/spring extend) CQ2-T-PS CQ2-T-PS CQ2-T-PS CQ-T-PS CQ2-T-PS CQ2-T-PS CQ2-T-PS Kits include items!4,!,! from the table. Seal kit includes!4,!,!. Order the seal kit, based on each bore size. Copper and Fluorine-free Series (For CRT anufacturing Process) Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) CQP2 Copper and fluorine-free series Stroke S T () ø, ø, ø, ø2, ø ø, ø For preventing the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. Specifications ction Proof pressure ax. operating pressure Rubber bumper Piping Piston speed ounting uto switch 2 Single acting, Single rod 1. Pa 1. Pa None Pipe thread to mm/s Through-hole ountable

122 xial Piping: Single cting, Single Rod Series CDQP2 With uto Switch Weight Weight ction Spring return Spring extend 2 2 Construction Spring return Cylinder stroke Refer to the below pages for further information on auto switches. 41 uto switch proper mounting position and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. (g) dditional Weight Rod end male thread ale thread Nut Calculation: (xample) CDQP2-S asic weight: CDQP2-S 242 g dditional weight: 43 g 2 g Spring extend 2 P.3 to (g) 3 dd each weight of auto switches when auto switches are mounted. arge ore ong Stroke Rod xial Piping nti-lateral oad Port size x. With nd ock uto switch - section (Port on rod end) Component Parts - section (Port on head end) No. 1 2 Description Cylinder tube Piston aterial luminum alloy luminum alloy Note Hard anodized Chromated 3 4 Piston rod Collar Stainless steel luminum alloy ø to ø2 ø to ø, nodized Carbon steel luminum alloy casted ø to ø, Hard chrome plated ø, Chromate, Painted Retaining ring ushing Return spring Carbon tool steel earing alloy Piano wire Phosphate coated Zinc chromated ronze element Sintered metallic C Retaining ring Carbon tool steel Port size Rc1/, 1/4 1 Plug with fixed orifice Steel ball Hexagon socket head set screw agnet Piston seal Rod seal Gasket lloy steel Carbon steel lloy steel NR NR NR Port size x. Nickel plated On spring extend (Type T), piston and piston rod are integrated (stainless steel). uto switch - section (Port on rod end) Replacement Parts/Seal Kit 2 Contents How to Order - section (Port on head end) Kit no. (Single acting/spring return) CQ2-S-PS CQ2-S-PS CQ2-S-PS CQ-S-PS CQ2-S-PS CQ2-S-PS CQ2-S-PS Kits include item!4 from the table. Seal kit includes!4. Order the seal kit, based on each bore size. Kit no. (Single acting/spring extend) CQ2-T-PS CQ2-T-PS CQ2-T-PS CQ-T-PS CQ2-T-PS CQ2-T-PS CQ2-T-PS Kits include items!4,!,! from the table. Seal kit includes!4,!,!. Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) 1 Water Resistant With uto Switch uto Switch ade to Order

123 Series CQP2 ounting olt for CDQP2/With uto Switch ounting method: ounting bolt for through-hole mounting of the CDQP2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-3x3 2 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt ounting bolt Spring Return Cylinder model CDQP2-S -S CDQP2-S -S CDQP2-S -S CDQP-S -S CDQP2-S -S CDQP2-S -S CDQP2-S -S C..... D ounting bolt part no. CQ-3 x 3 x CQ-3 x x 4 CQ- x x 4 CQ- x x 4 CQ- x x 4 CQ- x 4 x CQ- x x Spring xtend Cylinder model CDQP2-T -T CDQP2-T -T CDQP2-T -T CDQP-T -T CDQP2-T -T CDQP2-T -T CDQP2-T -T C D ounting bolt part no. CQ-3 x x 4 CQ-3 x x 4 CQ- x x 4 CQ- x x 4 CQ- x x 4 CQ- x 4 x CQ- x x

124 Compact Cylinder: xial Piping Single cting, Single Rod Dimensions ø to ø/ Spring Return Without uto Switch Series CQP2 ø to ø2 H thread effective depth C øi.3 2 K Z F Q J øi W ød W Plug 2 x øn through 4 x øo counterbore F 4. 1 x. (Port size) arge ore 2 st st st st Width across flat 1 C D H1 C F.. H 3 x. 4 x. x. x 1. I K Rod nd ale Thread N C1 1 O H1 4. depth 3.. depth 3. depth depth W x. x 1. x 1.2 x ong Stroke Rod xial Piping ø to ø H thread effective depth C Plug 4 x øn through x øo counterbore P (Rc, NPT, G) (Port size) nti-lateral oad ød With nd ock K Width across flat 1 Water Resistant st st st. st st st. C 1 H1 C1 For details about the rod end nut and accessory brackets, refer to page 1. 1 D F.. H x 1.2 x 1.2 x 1. I J. Rod nd ale Thread K C1.. 2 N... H1 O depth depth depth P 1/ 1/ 1/4 Q x 1. x 1. 1 x 1. W Z With uto Switch uto Switch ade to Order

125 Series CQP2 Dimensions ø to ø/ Spring Return With uto Switch ø to ø2 H thread effective depth C 2. uto switch inimum lead wire bending radius.3 øi S ød W 2 K F 4. 1 H1 C1 1 K Z F øi S ød W Q J U Plug Width across flat 1 2 x øn through 4 x øo counterbore x. (Port size) 2 For auto switch proper mounting position and its mounting height, refer to pages 3 to. C D st st st st F.. H 3 x. 4 x. x. x 1. I K Rod nd ale Thread N C1 1 O H1 4. depth 3.. depth 3. depth depth S x. x 1. x 1.2 x 1.2 U W ø to ø H thread effective depth C Plug 4 x øn through x øo counterbore P (Rc, NPT, G) (Port size) U 2. uto switch inimum lead wire bending radius Width across flat 1 For auto switch proper mounting position and its mounting height, refer to pages 3 to. C D st st st st. st st. H1 C1 1.. For details about the rod end nut and accessory brackets, refer to page F H x 1.2 x 1.2 x 1. I J. K 1 Rod nd ale Thread 34 N O depth depth depth C1.. 2 P 1/ 1/ 1/4 H1 Q S. 2 x 1. x 1. 1 x 1. U W Z 3 3 3

126 Compact Cylinder: xial Piping Single cting, Single Rod Dimensions ø to ø/ Spring xtend Without uto Switch Series CQP2 ø to ø2 H thread effective depth C øi.3 2 K Z F Q J øi W ød W 2 Plug Width across flat 1 st st st st C D H1 C F.. 2 x øn through 4 x øo counterbore x. (Port size) H 3 x. 4 x. x. x 1. I K st... F 1 1 st... 1 C N 4. Rod nd ale Thread H st st O. depth 3.. depth 3. depth depth W x. x 1. x 1.2 x arge ore ong Stroke Rod xial Piping ø to ø H thread effective depth C Plug P (Rc, NPT, G) (Port size) 4 x øn through x øo counterbore ød With nd ock nti-lateral oad K Width across flat 1 Water Resistant st 4. st.. st. st st H1 C1 st. 1.. For details about the rod end nut and accessory brackets, refer to page 1. C 1 D F H x 1.2 x 1.2 x 1. I Rod nd ale Thread J. K 1 st C1.. 2 st st 2 H1 34 st N... 1 st O depth depth depth st 3. P 1/ 1/ 1/4 x 1. x 1. 1 x 1. Q W Z With uto Switch uto Switch ade to Order

127 Series CQP2 Dimensions ø to ø/ Spring xtend With uto Switch ø to ø2 H thread effective depth C 2. uto switch inimum lead wire bending radius.3 øi ød W S 2 K H1 C1 1 F 4. 1 K Z F øi S ød W U Plug Width across flat 1 2 x øn through 4 x øo counterbore x. (Port size) Rod nd ale Thread C1 1 H1 4 st st x. x 1. x 1.2 x For auto switch proper mounting position and its mounting height, refer to pages 3 to. 1 2 C D F H I K st st st st st st x. 4 x. x. x N O. depth 3.. depth 3. depth depth S U W ø to ø H thread effective depth C Plug P (Rc, NPT, G) (Port size) 4 x øn through x øo counterbore Q J U 2. uto switch inimum lead wire bending radius Width across flat 1 H1 C1 Rod nd ale Thread 1 2 C1.. 2 H1 st st st 3. x 1. x 1. 1 x For auto switch proper mounting position and its mounting height, refer to pages 3 to. C D F H I J K st st st st st st st st st x 1.2 x 1.2 x For details about the rod end nut and accessory brackets, refer to page N... O depth depth depth P 1/ 1/ 1/4 Q S U W. 2 Z

128 ade to Order uto Switch With uto Switch Water Resistant With nd ock nti-lateral oad xial Piping Rod ong Stroke arge ore 2

129 xial Piping Series CDQP2 With uto Switch 1 1 uto Switch Proper ounting Position (Detection at Stroke nd) and its ounting Height pplicable Cylinder Series: CDQP2, CDQP2-S/-T (xial piping) D- D- D-W D- D-V D-V D-WV D-V U 2 ø to ø2 ø to ø U 2 D- D- D-H D-H D-F D-J D-FW D-JW D-FF D-FNT D-F D-3C D-C D-JC D-W D-FWV D-FV D-FV U ø to ø2 U ø to ø D-P4DW ø to ø U 3

130 Compact Cylinder: xial Piping Series CDQP2 uto Switch Proper ounting Position pplicable Cylinder Series: CDQP2 (xial piping) uto switch model 2 D- D-V D- D-V D-W D-WV D- D-V D-3 D D-2/H/H D-3C/C/F D-FF/J/FV D-JC/FW D-JW/FWV D-FV/F Note) djust the auto switch after confirming the operating conditions in the actual setting D-FNT D-W D-P4DW arge ore ong Stroke Rod pplicable Cylinder Series: CDQP2-S/-T (xial piping, Single acting) uto switch model 2 D- D-V (3).... D- D-V D-W D-WV D- D-V D-3 D- D-2/H/H D-3C/C/F D-FF/J/FV D-JC/FW D-JW/FWV D-FV/F D-FNT D-W () () () (.) (1.) (.) 2. (4.) ()..... (.)... (.).. ()... ()... ( ): Spring extend type Note) djust the auto switch after confirming the operating conditions in the actual setting.. (.).. () (.).. 1 (3) (4.) xial Piping nti-lateral oad With nd ock pplicable Cylinder Series: CDQP2, CDQP2-S/-T (xial piping) uto switch model 2 D- D-V D- D-V D-W D-WV D- D-V U D- D- U D-H D-H D-F D-J D-FW D-JW D-F D-FF D-FNT U D-3C D-C U D-FV D-FWV D-FV U D-JC U D-W U D-P4DW U Water Resistant With uto Switch uto Switch ade to Order 4

131 xial Piping Series CDQP2 With uto Switch 2 2 inimum Stroke for uto Switch ounting pplicable Cylinder Series: CDQP2, CDQP2-S/-T (xial piping) Number of auto switches With 1 pc. With 2 pcs. D-V D-FV D-JC D-V D- D- D-3C D-C D- D-WV D-V D-FWV D-FV 1 D- D-W D- D-H D-H D-F D-J 1 1 D-W 1 D-FW D-JW D-F D-FF D-FNT D-P4DW Operating Range pplicable Cylinder Series: CDQP2, CDQP2-S/-T (xial piping) uto switch model D-(V) D-(V) D-W(V) D-(V) D-(H)(C) D-(H)(C) D-W D-F(V) D-J(C) D-FW(V) D-F(V) D-FNT D-FF D-P4DW Values which include hysteresis are for guideline purposes only, they are not a guarantee (assuming approximately ±3% dispersion) and may change substantially depending on the ambient environment.

132 Compact Cylinder: xial Piping Series CDQP2 4 uto Switch ounting rackets/part No. pplicable Cylinder Series: CDQP2, CDQP2-S/-T (xial piping) uto switch mounting surface ø, ø, ø, ø2 ø to ø arge ore C ong Stroke uto switch model uto switch mounting surface uto switch mounting rail side only Q-1 Q2- Two kinds of auto switch brackets are used as a set. uto switch mounting surface //C side Q-2 Q2- Two kinds of auto switch brackets are used as a set. Rod D- D-V D- D-V D-W D-WV D- D-V Set screw (Not used) Set screw (Not used) nti-lateral oad xial Piping Note 1) When shipping cylinders, auto switch mounting brackets and auto switches are shipped together. uto switch model ø to ø2 D-/ D-3C/C D-H/H D-W D-F/J D-FV Q-1 D-JC D-FW/JW D-FWV D-F/FV D-FF/FNT D-P4DW ø ø to ø Q-2 QP1- Note 2) When shipping cylinders, auto switch mounting brackets and auto switches are shipped together. However, when the D-P4DW type with ø to ø is mounted, the auto switch is assembled at the time of shipment. Note 3) Refer to pages to 2 in est Pneumatics No. 2 for further information on auto switch mounting method. [Stainless Steel ounting Screw Kit] The following stainless steel mounting screw kit (with nuts) is available. Use it in accordance with the operating environment. (Since auto switch spacer (for Q- 2) is not included, order Q-2 separately.) 2: For D-//F/J types The above stainless steel screws are used when a cylinder is shipped with the D-F/FV auto switches. When only an auto switch is shipped independently, 2 is attached. Note 4) Refer to page 1 in est Pneumatics No. 2 for details of 2. Note ) When the D-(V) type is mounted, order auto switch mounting brackets Q2-S, Q-2 or the stainless steel mounting screw kit 2 separately. uto Switch ounting racket/weight ounting bracket part no. Q-1 Q-2 Q2- QP1- pplicable bore size ø to ø2 ø to ø ø to ø2 ø to ø Weight (g) With nd ock Water Resistant ade to Order With uto Switch uto Switch

133 xial Piping Series CDQP2 With uto Switch 3 Other than the applicable auto switches listed in How to Order, the following auto switches are mountable. Refer to est Pneumatics No. 2 for detailed specifications. pplicable Cylinder Series: CDQP2, CDQP2-S/-T (xial piping) uto switch type odel lectrical entry Features Reed D-3 Grommet (Perpendicular) D- Without indicator light D-3H, H Grommet (In-line) D-H Without indicator light D-FNV, FPV, FV D-FNWV, FWV D-FV Grommet (Perpendicular) Diagnostic indication (2-color indication) Water resistant (2-color indication) D-F, FP, J Solid state D-FW, FPW, JW Diagnostic indication (2-color indication) Grommet (In-line) D-F Water resistant (2-color indication) D-FNT D-PDW Grommet (In-line) With timer agnetic field resistant (2-color indication) pplicable bore size ø to ø ø to ø ø to ø With pre-wired connector is also available for solid state auto switches. For details, refer to est Pneumatics No. 2. Normally closed (NC = b contact) solid state auto switches (D-FG/FH) are also available. For details, refer to est Pneumatics No. 2. When using a magnetic field resistant solid state auto switch D-P3DW type, please contact SC separately. (pplicable bore size: ø to ø) Heat resistant solid state auto switch (D-FNJ) is not applicable. Regarding the D-PDW, please contact SC separately.

134 Without auto switch With auto switch Compact Cylinder: nti-lateral oad Series CQ2 ø, ø, ø, ø, ø, ø CQ2 CDQ2 S S How to Order 3 D 3 D C C Z Z W arge ore F G D With auto switch (uilt-in magnet) ounting Through-hole () oth ends tapped Foot Rod flange Head flange Double clevis ounting brackets are shipped together, (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to ounting olt for C(D)Q2S on pages 3 and 4. uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2S-3DCZ S Type nti-lateral load mm mm mm mm mm mm Port thread type Nil TN TF Rc NPT G Cylinder stroke Refer to the next page for standard strokes. D ction Double acting ade to Order Refer to the next page for details. Number of auto switches Nil S n uto switch mounting groove Z 4 surfaces ody option 2 Nil Cushion C Rubber bumper ody option 1 Nil F With boss on head end 2 pcs. 1 pc. n pcs. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. (Rod end female thread) ong Stroke Rod xial Piping nti-lateral oad With nd ock Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. pplicable uto Switches/ Refer to the individual catalog (S-1) for the D-P3DW type. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) agnetic field resistant (2-color indication) lectrical entry Grommet Indicator light Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 2-wire (Non-polar) 3-wire (NPN equivalent) oad voltage DC C 24 V V, V V V, V V V, V V uto switch model Perpendicular NV PV V NWV PWV WV NV PV V In-line N P NW PW W N P P3DW ead wire length (m). (Nil) 1 () 3 () None (Z) (N) Grommet V V Yes V V 3V 3 2-wire 24 V No V, V V or less V Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW Solid state auto switches marked with are produced upon receipt of order. 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2. Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC Water Resistant With uto Switch uto Switch ade to Order

135 Series CQ2 Specifications JIS Symbol Double acting, Single rod ction Fluid Proof pressure aximum operating pressure inimum operating pressure mbient and fluid temperature ubrication Piston speed Double acting, Single rod ir 1. Pa 1. Pa. Pa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Not required (Non-lube) to mm/s llowable kinetic energy (J) Stroke length tolerance mm 1.4 Note) Note) Stroke length tolerance does not include the amount of dumper change. Symbol - -C ade to Order (For details, refer to pages 1 to.) Specifications Intermediate stroke (xclusive body type) Piston rod/retaining ring/rod end nut material: Stainless steel Strokes,,,, stroke,, 1,, 2, 3, 3,, 4,,,, 1,, 2, 3, 3,, 4,,, anufacture of Intermediate Strokes -C2 -C2-21 With split pins for double clevis pin/ double knuckle joint pin and flat washers Double clevis pin/double knuckle joint pin material: Stainless steel 34 Fluororubber seals Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2. ven if a proper plier (tool for installing a type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). e much careful with the popping of a retaining ring. esides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment. Type Part no. Description Stroke range xample spacer is installed in the standard stroke body. Refer to How to Order for the standard model number. (P. ) Strokes in 1 mm intervals are available by installing a spacer in the standard stroke cylinder. to Stroke range 1 to Part no.: CQ2S-DCZ CQ2S-DCZ with 1 mm width spacer inside The dimension is. mm. xclusive body (-) Suffix - to the end of standard model number. (P. ) Strokes in 1 mm intervals are available by using an exclusive body with the specified stroke., to Stroke range to to Part no.: CQ2S-DCZ- akes stroke tube. The dimension is. mm. In the case of exclusive body type with ø to ø (-) with the stroke length exceeding mm, reference values of the longitudinal dimension will be changed. Calculate length dimensions by deducting from those of or mm stroke models. Type Pneumatic Through-hole () ounting oth ends tapped uilt-in magnet Piping Pipe thread With rubber bumper () With boss on head end Rc1/ Rc1/4 Rc1/4 Rc3/ Rc3/ Rc1/ NPT1/ G1/ NPT1/ G1/ NPT1/4 G1/4 NPT1/4 G1/4 NPT3/ G3/ NPT3/ G3/ Refer to pages to 1 for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no.

136 Compact Cylinder: nti-lateral oad Series CQ2 Copper and Fluorine-free Series (For CRT anufacturing Process) llowable ateral oad at Rod nd -CQ2S Stroke DC()Z Copper and fluorine-free series ø, ø, ø, ø ø, ø For preventing the influence of copper ions or halogen ions during CRT manufacturing processes, copper and fluorine materials are not used in the component parts. Specifications ction Proof pressure ax. operating pressure Rubber bumper Piping Piston speed ounting uto switch Double acting, Single rod 1. Pa 1. Pa With () Pipe thread to mm/s Through-hole/oth ends tapped ountable Without uto Switch llowable lateral load at rod end (N) 3 ø ø ø ø ø ø 3 Cylinder stroke With uto Switch llowable lateral load at rod end (N) 3 ø ø ø ø ø ø 3 Cylinder stroke arge ore ong Stroke Theoretical Output Weight Weight Operating direction IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT dditional Weight (g) Cylinder stroke oth ends tapped ale thread Nut Foot (Including mounting bolts) Rod flange (Including mounting bolts) Head flange (Including mounting bolts) Double clevis (Including pin, retaining rings, bolts) Calculation: (xample) CQ2DS-DCZ asic weight: CQ2S-DCZ 13 g dditional weight: oth ends tapped g 43 g Double clevis g 33 g OUT Operating pressure (Pa) IN (N) (g) Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

137 Series CQ2 Construction Component Parts No Description Cylinder tube Piston Piston rod Collar Retaining ring umper umper ushing Wear ring Rod end nut Rod seal Piston seal Tube gasket aterial luminum alloy luminum alloy Carbon steel luminum alloy Carbon tool steel Urethane Urethane earing alloy Resin Carbon steel NR NR NR Note Hard anodized Chromated Hard chrome plated nodized Phosphate coated Nickel plated Replacement Parts/Seal Kit Kit no. Contents CQ2-PS CQ2-PS Kits include items CQ2-PS!1,!2,!3 from CQ2-PS the table. CQ2-PS CQ2-PS Seal kit includes!1,!2,!3. Order the seal kit based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) ounting rackets/part No. Foot Note 1) Flange Double clevis CQ- CQ- CQ- CQ- CQ- CQ- CQ-F CQ-F CQ-F CQ-F CQ-F CQ-F CQ-D CQ-D CQ-D CQ-D CQ-D CQ-D Note 1) When ordering a foot bracket, order 2 pieces per cylinder. Note 2) Parts belonging to each bracket are as follows. Foot or Flange: ody mounting bolts Double clevis: Clevis pin, Type C retaining rings for axis, ody mounting bolts 1

138 nti-lateral oad Series CDQ2 With uto Switch Refer to the below pages for further information on auto switches. uto switch proper mounting position and its mounting height inimum stroke for auto switch mounting P. to 1 Operating range uto switch mounting brackets/part no. arge ore Weight Weight (g) dditional Weight (g) Cylinder stroke oth ends tapped ale thread Nut Foot (Including mounting bolts) Rod flange (Including mounting bolts) Head flange (Including mounting bolts) Double clevis (Including pin, retaining rings, bolts) Calculation: (xample) CDQ2DS-DCZ asic weight: CDQ2S-DCZ 2 g dditional weight: oth ends tapped g 43 g Double clevis g 4 g dd each weight of auto switches when auto switches are mounted. Construction uto switch ong Stroke Rod xial Piping Water Resistant nti-lateral oad With nd ock Component Parts No Description Cylinder tube Piston Piston rod Collar Retaining ring umper umper ushing Wear ring agnet Rod seal Piston seal Tube gasket aterial luminum alloy luminum alloy Carbon steel luminum alloy Carbon tool steel Urethane Urethane earing alloy Resin NR NR NR Note Hard anodized Chromated Hard chrome plated nodized Phosphate coated Replacement Parts/Seal Kit Kit no. Contents CQ2-PS CQ2-PS Kits include items CQ2-PS!1,!2,!3 from CQ2-PS the table. CQ2-PS CQ2-PS Seal kit includes!1,!2,!3 Order the seal kit based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) With uto Switch uto Switch ade to Order 1

139 Series CQ2 ounting olt for CQ2S/Without uto Switch ounting method: ounting bolt for through-hole mounting of the CQ2S is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-x 4 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt Cylinder model C D ounting bolt part no. CQ2S-DCZ -DCZ -1DCZ -DCZ -2DCZ 4 CQ- x x 4 x x x -3DCZ x -3DCZ x -DCZ -4DCZ -DCZ -DCZ -DCZ CQ2S-DCZ -DCZ -1DCZ -DCZ -2DCZ 4 x x x x x CQ- x 4 x x x x -3DCZ x. -3DCZ x -DCZ -4DCZ -DCZ -DCZ -DCZ CQ2S-DCZ -1DCZ -DCZ -2DCZ -3DCZ -3DCZ -DCZ -4DCZ -DCZ -DCZ -DCZ. 1 1 x x x x x 1 CQ- x x x x x x x x x x x 1 Cylinder model C D ounting bolt part no. CQ2S-DCZ -1DCZ -DCZ -2DCZ -3DCZ -3DCZ -DCZ -4DCZ -DCZ -DCZ -DCZ CQ2S-DCZ -1DCZ -DCZ -2DCZ -3DCZ -3DCZ -DCZ -4DCZ -DCZ -DCZ -DCZ CQ2S-DCZ -1DCZ -DCZ -2DCZ -3DCZ -3DCZ -DCZ -4DCZ -DCZ -DCZ -DCZ CQ- x x x x x x x x x x x CQ- x x x x x x x x x x 1 x CQ- x x x x x x x x 1 x x 1 x 1 3

140 Compact Cylinder: nti-lateral oad Series CQ2 ounting olt for CDQ2S/With uto Switch ounting method: ounting bolt for through-hole mounting of the CDQ2S is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-x 4 pcs. aterial: Chromium molybdenum steel Surface treatment: Nickel plated ounting bolt Cylinder model C D ounting bolt part no. CDQ2S-DCZ -DCZ -1DCZ -DCZ -2DCZ CQ- x x x x x -3DCZ x -3DCZ x -DCZ -4DCZ -DCZ -DCZ -DCZ CDQ2S-DCZ -DCZ -1DCZ -DCZ -2DCZ x x x x x CQ- x x x x x -3DCZ x. -3DCZ x -DCZ -4DCZ -DCZ -DCZ -DCZ CDQ2S-DCZ -1DCZ -DCZ -2DCZ -3DCZ -3DCZ -DCZ -4DCZ -DCZ -DCZ -DCZ. 1 1 x x x x x 1 CQ- x x x x x x x x x x x 1 Cylinder model C D ounting bolt part no. CDQ2S-DCZ -1DCZ -DCZ -2DCZ -3DCZ -3DCZ -DCZ -4DCZ -DCZ -DCZ -DCZ CDQ2S-DCZ -1DCZ -DCZ -2DCZ -3DCZ -3DCZ -DCZ -4DCZ -DCZ -DCZ -DCZ CDQ2S-DCZ -1DCZ -DCZ -2DCZ -3DCZ -3DCZ -DCZ -4DCZ -DCZ -DCZ -DCZ CQ- x x x x x x x x x 1 x x CQ- x x x x x x x x 1 x x 1 x CQ- x x x x x x 1 x x x x 1 x 1 ade to Order uto Switch arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock With uto Switch Water Resistant 4

141 Series CQ2 Dimensions ø to ø/with uto Switch (Through-hole): CQ2S/CDQ2S (In the case of without auto switches, the, dimensions will be only changed. Refer to the dimension table.) oth ends tapped: CQ2S/CDQ2S O1 thread CDQ2S R R oth nds Tapped O1 x 1. x 1. x 1.2 R H thread effective depth C 4 x øn through x øo counterbore 2 x P (Rc, NPT, G) (Port size) Q uto switch inimum lead wire bending radius F Z ød K W J + Stroke + Stroke Width across flat 1 H1 C1 1 The dimensions with boss on head end are equivalent to those of the CQ2 series, double acting, single rod. Refer to page 1. Rod nd ale Thread 1 C1 H x 1. x 1. 1 x Stroke range Without auto switch With auto switch to to to ,,, C D F H J K N O P Q x x 1.2. x depth depth depth 1/. 1/ 1/4. W 4. 1 Z 1 1

142 Compact Cylinder: nti-lateral oad Series CQ2 Foot: CQ2S/CDQ2S F FZ Z 1 1 H Y 4 x ød Special cap bolt FV 4 x øfd + Stroke + Stroke CT 1 FT + Stroke CW C + Stroke + Stroke 1 Y FT + Stroke + Stroke 4 x N Cap bolt CU RR + Stroke T + Stroke Rod flange: CQ2FS/CDQ2FS FV øcd hole H xis d Y Head flange: CQ2GS/CDQ2GS G S + Stroke Special cap bolt Double clevis: CQ2DS/CDQ2DS F FZ Special cap bolt C CZ x øfd Foot Rod Flange Head Flange Stroke range to, to, to, Stroke range to, to, to, Stroke range to, to, to, Stroke range to, to, to, to, to, to, Stroke range to, to, to, Stroke range to, to, to, Without auto switch S G H T With auto switch.2 43 S Y Z Y Foot bracket material: Carbon steel Surface treatment: Nickel plated Without auto switch With auto switch FD FT FV F FZ Without auto switch Flange bracket material: Carbon steel Surface treatment: Nickel plated Stroke range The dimensions except, and 1 are the same as those of the rod flange. Double Clevis With auto switch 4.. Without auto switch C CW 2 C 1 1 CZ With auto switch 43 C N CD x 1. x 1. x Flange bracket material: Carbon steel Surface treatment: Nickel plated Double clevis bracket material: Cast iron Surface treatment: Painted For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. CT RR D.. CU arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

143 Series CQ2 Dimensions ø to ø/with uto Switch (Through-hole): CQ2S/CDQ2S The dimensions with boss on head end are equivalent to those of the CQ2 series, double acting, single rod. Refer to page 1. (In the case of without auto switches, the, dimensions will be only changed. Refer to the dimension table.) oth ends tapped: CQ2S/CDQ2S O1 thread R R oth nds Tapped O1 x 1. x 1. x 1. R 1 H thread effective depth C 2 x P (Rc, NPT, G) (Port size) 4 x øn through x øo counterbore Q inimum lead wire bending radius uto switch F Z ød K W J + Stroke + Stroke Width across flat 1 H1 C1 1 Rod nd ale Thread 1 C1 H x 1. x 1. 2 x Stroke range Without auto switch With auto switch to to to ,,, C D 2 3 F.. H x 1. x 2. x 2. J. K N O depth. 1. depth. 1. depth. P 1/4 3/ 3/ Q 1 23 W Z 1 2 2

144 Compact Cylinder: nti-lateral oad Series CQ2 Foot: CQ2S/CDQ2S Z F FZ 1 1 H Y Special cap bolt FV + Stroke + Stroke 4 x ød 4 x øfd FT 4 x N Cap bolt CT + Stroke CW C + Stroke + Stroke 1 1 FV FT + Stroke CU RR Y T + Stroke Rod flange: CQ2FS/CDQ2FS Y Head flange: CQ2GS/CDQ2GS F FZ Double clevis: CQ2DS/CDQ2DS øcd hole H xis d + Stroke Special cap bolt G S + Stroke + Stroke C CZ Special cap bolt x øfd Foot Rod Flange Head Flange Stroke range to, to, to, Stroke range to, to, to, Stroke range to, to, to, Stroke range to, to, to, to, to, to, Stroke range to, to, to, Without auto switch S G H T With auto switch 2.2 S Y 1. 1 Without auto switch With auto switch FD Without auto switch Flange bracket material: Carbon steel Surface treatment: Nickel plated Stroke range The dimensions except, and 1 are the same as those of the rod flange. Double Clevis Stroke range to, to, to, With auto switch 3 4. Without auto switch C CW C CZ Z Y. Foot bracket material: Carbon steel Surface treatment: Nickel plated FT FV F FZ Flange bracket material: Carbon steel Surface treatment: Nickel plated With auto switch C N x 1. x 1. x 1. D CD CT CU Double clevis bracket material: Cast iron Surface treatment: Painted For details about the rod end nut and accessory brackets, refer to page 1. Double clevis pin and retaining rings are included. 1 RR arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

145

146 Without auto switch With auto switch ø, ø2 F G D 2 mm 2 mm mm mm mm mm mm mm CQ2 CDQ2 With auto switch (uilt-in magnet) ounting ø to ø Through-hole/oth ends tapped common () Foot Rod flange Head flange Double clevis Note 1) ounting brackets are shipped together, (but not assembled). Note 2) t the and mm strokes with ø, ø, both ends tapped () is the standard. Throughhole () is not available. Cylinder stroke Refer to the next page for standard strokes and intermediate strokes. F G D Compact Cylinder: With nd ock Series CQ2 ø, ø2, ø, ø, ø, ø, ø, ø Through-hole () Note 2) oth ends tapped Foot Rod flange Head flange Double clevis Note 3) ounting brackets are shipped together, (but not assembled). Nil TN TF Port thread type thread Rc NPT G ø, ø2 ø to ø How to Order 3 D C 3 D C H H N N ock position H Head end lock R Rod end lock ody option Nil C Cushion C Rubber bumper ction D Double acting Rod end female thread ø, ø2 ø to ø ø, ø2 ø ø to ø NV PV V JC N P NWV PWV WV NV PV V NW PW W N P FF P4DW V 2 2H 3V 3 V 3C C W W Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. pplicable uto Switches/Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) agnetic field resistant (2-color indication) Diagnostic indication (2-color indication) lectrical entry Grommet Indicator light No Yes No Yes Wiring (Output) 2-wire Connector 3-wire (NPN) 3-wire (PNP) Yes 2-wire 3-wire (NPN) Grommet 3-wire (PNP) 2-wire 4-wire 2-wire (Non-polar) 3-wire (NPN equivalent) Yes Grommet Connector Grommet 3-wire (NPN) 3-wire (PNP) 2-wire oad voltage DC V, V V C 24 V V, V V V, V V V, V 24 V V V V, V V V, V V V V or less 24 V or less uto switch model Perpendicular In-line Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. ead wire length symbols:. m Nil (xample) NW 1 m (xample) NW 3 m (xample) NW m Z (xample) NWZ None N (xample) JCN anual release type N Non-lock type ock type ade to Order Refer to the next page for details. uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2-3DC-R ead wire length (m). (Nil) 1 () 3 () None (Z) (N) Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit Solid state auto switches marked with are produced upon receipt of order. The D-P4DW type is available from ø to ø only. Only for the D-P4DW type, an auto switch is assembled and shipped with the cylinder. There are other applicable auto switches other than the listed above. For details, refer to page 1. For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2. When the D-(V)/(V)/W(V)/(V) types with ø to ø are mounted on a surface other than the port side, order auto switch mounting brackets separately. Refer to page for details. Relay, PC Relay, PC 1 arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

147 Series CQ2 Specifications 2 ction Fluid Proof pressure aximum operating pressure inimum operating pressure mbient and fluid temperature ubrication Piston speed Double acting, Single rod ir 1. Pa 1. Pa.1 Pa Note) Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Not required (Non-lube) to mm/s llowable kinetic energy (J) Stroke length tolerance ock position +1. mm Head end, Rod end Holding force (ax.) (N) Pressure for unlocking acklash anual release.1 Pa or less 2 mm or less Non-lock type, ock type Note). Pa except for the end lock unit ade to Order (For details, refer to pages 1 to.) Symbol Specifications With split pins for double clevis pin/ -C2 double knuckle joint pin and flat washers Strokes to, stroke, 1,, 2,,, 2,,, Refer to pages to 1 for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. anufacture of Intermediate Strokes Type Part no. Description Stroke range xample spacer is installed in the standard stroke body. Refer to How to Order for the standard model number. (P. 1) Strokes in mm intervals are available by installing a spacer in the standard stroke cylinder. to Stroke range to Part no.: CQ2-4DC-H CQ2-DC-H with mm width spacer inside ounting rackets/part No. 2 Foot Note 1) Flange Double clevis Note 2) CQS- CQS-2 CQ- CQ- CQ- CQ- CQ- CQ- CQS-F CQS-F2 CQ-F CQ-F CQ-F CQ-F CQ-F CQ-F CQS-D CQS-D2 CQ-D CQ-D CQ-D CQ-D CQ-D CQ-D Note 1) When ordering a foot bracket, order 2 pieces per cylinder. Note 2) Parts belonging to each bracket are as follows. Foot or Flange: ody mounting bolts Double clevis: Clevis pin, Type C retaining rings for axis, ody mounting bolts Note 3) Clevis pin and retaining rings are included with double clevis. 1

148 Compact Cylinder: With nd ock Series CQ2 llowable Kinetic nergy llowable ateral oad at Rod nd With Rubber umper oad mass (kg) aximum speed (mm/s). Pa.4 Pa ø ø ø ø ø ø ø2 ø With uto Switch llowable lateral load at rod end W (N) Cylinder stroke ø ø ø ø ø ø ø2 ø arge ore ong Stroke Rod (ounting orientation: W Horizontal) ade to Order uto Switch With uto Switch xial Piping Water Resistant With nd ock nti-lateral oad 2

149 Series CQ2 ounting olt for CQ2 ounting method: ounting bolt for through-hole mounting of the CQ2 is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-x 4 pcs. Note) e sure to use the attached flat washers when mounting ø and ø2 cylinders with through-holes. ounting bolt aterial: Chromium molybdenum steel Surface treatment: Nickel plated With Head nd ock (H) Cylinder model C D CQ2-DC-H -1DC-H -DC-H -2DC-H -DC-H -DC-H -DC-H CQ-DC-H -1DC-H -DC-H -2DC-H -DC-H -DC-H -DC-H CQ2-DC-H -1DC-H -DC-H -2DC-H -DC-H -DC-H -DC-H CQ2-DC-H -1DC-H -DC-H -2DC-H -DC-H -DC-H -DC-H ounting bolt part no. CQ- x x x x x x x 1 CQ- x x x x x x x 1 CQ- x x x x x x 1 x CQ- x x x x x x 1 x 1 Cylinder model C D CQ2-DC-H -1DC-H -DC-H -2DC-H -DC-H -DC-H -DC-H CQ2-DC-H -1DC-H -DC-H -2DC-H -DC-H -DC-H -DC-H CQ2-2DC-H. -DC-H CQ2-2DC-H -DC-H 1 ounting bolt part no. CQ- x x x x x x 1 x 1 CQ- x x x x x x 1 x 1 CQ- x x CQ- x x 1 With Rod nd ock (R) Cylinder model C D CQ2-DC-R -1DC-R. -DC-R -2DC-R -DC-R -DC-R -DC-R CQ-DC-R 1-1DC-R. -DC-R -2DC-R -DC-R -DC-R -DC-R CQ2-DC-R -1DC-R -DC-R -2DC-R -DC-R -DC-R -DC-R CQ2-DC-R -1DC-R -DC-R -2DC-R -DC-R -DC-R -DC-R ounting bolt part no. CQ- x x x x x x x 1 CQ- x x x x x x x 1 CQ- x x x x x 1 x x CQ- x x x x x x 1 x Cylinder model C D CQ2-DC-R -1DC-R -DC-R -2DC-R -DC-R -DC-R -DC-R CQ2-DC-R -1DC-R -DC-R -2DC-R -DC-R -DC-R -DC-R CQ2-2DC-R -DC-R CQ2-2DC-R -DC-R ounting bolt part no. CQ- x x x x x x x 1 CQ- x x x x x x 1 x 1 CQ- x x 1 CQ- x 1 x

150 Compact Cylinder: With nd ock Series CQ2 Construction ø to ø anual release (ock type): Suffix Head end lock Cylinder tube form ø to ø Rod end lock ø, 2 Cylinder tube form ø2 or less ø, Cylinder tube form ø or more nti-lateral oad Rod arge ore ong Stroke xial Piping Component Parts No Description Cylinder tube Piston Piston rod Collar Retaining ring ushing agnet umper umper Piston seal Rod seal Tube gasket ock piston seal Piston gasket ock piston Gasket ock spring umper Head cover ock bolt Hexagon socket head cap screw Rubber cap Cap Cap aterial Note luminum alloy Hard anodized luminum alloy Chromated Carbon steel Hard chrome plated R luminum alloy nodized H luminum alloy ø or less, nodized luminum alloy casted ø or more, Painted after chromated Carbon tool steel Phosphate coated Copper alloy Urethane Urethane NR NR NR NR NR Carbon steel NR Stainless steel Urethane luminum alloy Carbon steel lloy steel Synthetic rubber luminum casted Carbon steel R H Used for all bore sizes Used for ø or more With auto switch Using 4 pcs. for ø, ø Nothing for ø, ø2 Quenched, Hard chrome plated nodized Quenched, lectroless nickel plated lack zinc chromated lack painted Oxide film treated No Description /O knob /O bolt /O spring Stopper ring Hexagon socket head cap screw aterial Zinc die-casted lloy steel Steel wire Rolled steel lloy steel Note lack painted lack zinc chromated, Red painted Zinc chromated Zinc chromated Nickel plated Replacement Parts/Seal Kit (nd lock type) Kit no. Contents 2 CQ2-PS CQ-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS CQ2-PS Kits from the table and a grease pack. Seal Order the seal kit based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) 4 With nd ock Water Resistant With uto Switch uto Switch ade to Order

151 Series CQ2 Dimensions ø, ø2 (Through-hole/oth ends tapped common): CQ2/CDQ2 2 x 4 x øo counterbore depth R 1 With head end lock nd lock mechanism H thread effective depth C anual release 2 x 4 x O non-lock type effective depth R 2 x x. 24 ø D nd lock mechanism (anual release lock type) ø1 øi K HR 1 ød Flat washer Q + Stroke + Stroke Q 4 x øn through 2 D 21 D HN nd ock echanism Dimensions HR HN (ax.) With rod end lock nd lock mechanism anual release non-lock type 2 x x. D ø 24 1 ød 4 x øn through Flat washer Q + Stroke + Stroke F H1 Rod nd ale Thread stroke C1 H1 1 C1 2, 1,, 2,,, 1,, 2,, 1 1. x 1.2 x stroke, 1,, 2,,, 1,, 2,, With head end lock With rod end lock F C D 3 H x. x 1. I 4 2 K 2. 2 N.4.4 O x 1. x 1. O Q R R

152 Compact Cylinder: With nd ock Series CQ2 Foot: CQ2/CDQ2 1 1 Z F FZ Special cap bolt H Y 4 x ød Rod end nut Rod flange: CQ2F/CDQ2F FV Rod end nut 2 x øfd FT CT + Stroke CW C + Stroke + Stroke 1 1 Head flange: CQ2G/CDQ2G Rod end nut + Stroke + Stroke Double clevis: CQ2D/CDQ2D Rod end nut CU RR Y Y G S + Stroke + Stroke T FT + Stroke + Stroke F FZ Cap bolt øcd hole H xis d + Stroke FV 2 x øfd C CZ Foot 2 2 Rod Flange With head end lock With rod end lock stroke, 1,, ,,.., 1,, ,, 4 4 stroke With head end lock With rod end lock 1 1, 1,, ,, , 1,, ,, Double Clevis With head end lock stroke C 1, 1,, ,,... 2., 1,, ,, stroke With head end lock S, 1,, 2,,, 1,, 2,, stroke, 1,, 2,, stroke, 1,, 2,, Head Flange stroke, 1,, 2,, FD.. stroke CD CT CU CW C CZ RR, 1,, 2,, FD.. FT FV F With rod end lock S D G H T Y Z FT FV F 4 2 FZ FZ 4 With rod end lock C Y.2... Foot bracket material: Carbon steel Surface treatment: Nickel plated Flange bracket material: Carbon steel Surface treatment: Nickel plated Flange bracket material: Carbon steel Surface treatment: Nickel plated Double clevis bracket material: Carbon steel Surface treatment: Nickel plated arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

153 Series CQ2 Dimensions ø to ø (Through-hole): CQ2/CDQ2 oth ends tapped: CQ2/CDQ2 H thread effective depth C W 4 x øn through 2 x 4 x øo counterbore depth R O1 thread R1 With head end lock nd lock mechanism anual release non-lock type ørf R1 D oth nds Tapped O1 x 1. x 1. x 1.2 x 1. x 1. x 1. With rod end lock D R1 1 øi Z ød HR K W J 2 x P (Port size) Q + Stroke + Stroke Q Q + Stroke + Stroke F Cylinder tube form ø, ø, ø nd lock mechanism (anual release lock type) øo HN nd ock echanism Dimensions D D HR HN (ax.) O W RF H1 C1 1 Rod nd ale Thread stroke, 1,, 2,, 2,, 2,, C H1 x 1. x 1. 1 x 1. 1 x 1. x 1. 2 x stroke, 1,, 2,, 2,,,, 1,, 2,, 2,, 2,, C D H x 1.2 x 1.2 x 1. x 1. x 2. x 2. Q I 3 1 t the and mm strokes with ø, ø, both ends tapped () is the standard. Through-hole () is not available. With Head nd ock stroke J 4.. K With Rod nd ock stroke, 1,, 2,, 2,, 2,, N O P Rc1/ Rc1/ Rc1/4 Rc1/4 Rc3/ Rc3/ F R... W Z Q

154 Compact Cylinder: With nd ock Series CQ2 Foot: CQ2/CDQ2 Z H Y 4 x ød Rod end nut 1 + Stroke Y Y S + Stroke T + Stroke Special cap bolt G Foot With head end lock With rod end lock stroke S S, 1,, 2,, , , , , stroke, 1,, 2,, 2,,, G 4 4 H T Y Z Y.. Foot bracket material: Carbon steel Surface treatment: Nickel plated D.. xial Piping arge ore ong Stroke Rod Rod flange: CQ2F/CDQ2F FV 4 x øfd F FZ FT + Stroke + Stroke Rod Flange With head end lock With rod end lock stroke FD, 1,, 2,, , , 1 1 2, 2.. 1,.... stroke 1 FT FV 4 4 F FZ 2 4 nti-lateral oad With nd ock Water Resistant Rod end nut 1, 1,, 2,, 2,,, Flange bracket material: Carbon steel Surface treatment: Nickel plated With uto Switch ade to Order uto Switch

155 Series CQ2 Dimensions ø to ø Head flange: CQ2G/CDQ2G + Stroke + Stroke FT F FZ FV 4 x øfd Head Flange With head end lock With rod end lock stroke 1 1, 1,, 2,, , , , , stroke FD FT FV F FZ 1 Rod end nut, 1,, 2,, Flange bracket material: Carbon steel Surface treatment: Nickel plated Double clevis: CQ2D/CDQ2D 1 CT + Stroke CW C + Stroke + Stroke Rod end nut øcd hole H xis d CU RR 4 x N Cap bolt C CZ.1.3 Double Clevis With head end lock With rod end lock stroke CD CT CU C C, 1,, ,, , , , , stroke CW C CZ, 1,, 2,, 2,,, N x 1. x 1. x 1.2 x 1. x 1. x 1. RR 1 Double clevis bracket material: Cast iron Surface treatment: Painted

156 Compact Cylinder: With nd ock Series CQ2 Use the Recommended Pneumatic Circuit Caution This is necessary for the correct locking and unlocking actions. With head end lock Operating Precautions Caution 1. Do not use 3-position solenoid valves. void use in combination with 3-position solenoid valves (especially closed center metal seal types). If pressure is trapped in the port on the lock mechanism side, the cylinder cannot be locked. Furthermore, even after being locked, the lock may be released after some time, due to air leaking from the solenoid valve and entering the cylinder. 2. ack pressure is required for releasing the lock. efore starting operation, be sure to control the system so that air is supplied to the side without the lock mechanism as shown in the above figure. There is a possibility that the lock may not be released. (Refer to the section on releasing the lock.) 3. Release the lock for mounting or adjusting the cylinder. If mounting or other work is performed when the cylinder is locked, the lock unit may be damaged. 4. Operate with a load ratio of % or less. If the load ratio exceeds %, this may cause problems such as failure of the lock to release, or damage to the lock unit.. Do not operate multiple cylinders in synchronization. void applications in which two or more end lock cylinders are synchronized to move one work piece, as one of the cylinder locks may not be able to release when required.. Use a speed controller with meter-out control. ock cannot be released occasionally by meter-in control.. e sure to operate completely to the cylinder stroke end on the side with the lock. If the cylinder piston does not reach the end of stroke, locking and unlocking may not be possible.. djust the position of an auto switch, so that it could work at the both positions where it is distanced from the stroke and a backlash (2 mm). When a 2-color indication switch is adjusted for green indication at the stroke end, it may change to red for the backlash return, but this is not abnormal. Caution Operating Pressure With rod end lock 1. Supply air pressure of.1 Pa or higher to the port on the side that has the lock mechanism, as it is necessary for releasing the lock. Caution xhaust Speed 1. When the pressure on the side with the lock mechanism drops to. Pa or below, the lock engages automatically. If the piping on the side with the lock mechanism is thin and long, or if the speed controller is away from the cylinder port, the lock engagement may take some time due to decline of the exhaust speed. The same result will be caused by clogging of the silencer installed at the H port of the solenoid valve. Warning Caution Releasing the ock 1. efore releasing the lock, be sure to supply air to the side without the lock mechanism, so that there is no load applied to the lock mechanism when it is released. (Refer to the recommended pneumatic circuits.) If the lock is released when the port on the other side is in an exhaust state, and with a load applied to the lock unit, the lock unit may be subjected to an excessive force and be damaged. lso, it is very dangerous because the piston rod will be rushed to move. anual Release 1. anual release (Non-lock type) Insert the accessory bolt from the top of the rubber cap (it is not necessary to remove the rubber cap), and after screwing it into the lock piston, pull it to release the lock. If you stop pulling the bolt, the lock will return to an operational state. Thread sizes, pulling forces and strokes are as shown below., 2,,,, Thread size 2. x.4 x 2 l or more 3 x. x 3 l or more x. x l or more Remove the bolt for normal operation. It can cause lock malfunction or faulty release. Rubber cap 2. anual release (ock type) While pushing the /O knob, turn it counterclockwise. The lock is released (and remains in a released state) by aligning the mark on the cap with the OFF mark on the /O knob. When locking is desired, turn the /O knob clockwise while pushing fully, correspond on cap and ON mark on the /O knob. The correct position is confirmed by a click sound click. If not confirmed, locking is not done. Unlock anually locked state ock Pulling force (N) anually unlocked state Stroke arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order

157 With nd ock Series CDQ2 With uto Switch 1 1 uto Switch Proper ounting Position (Detection at Stroke nd) and its ounting Height pplicable Cylinder Series: CDQ2 (With end lock) D- D- D-W D- D-V D-V D-WV D-V ø, ø2 U ø to ø U D- D- D-H D-H D-F D-J D-FW D-JW D-FF D-FNT D-F D-3C D-C D-JC D-W D-FWV D-FV D-FV U ø to ø D-P4DW ø to ø U

158 Compact Cylinder: With nd ock Series CDQ2 uto Switch ounting Height pplicable Cylinder Series: CDQ2 (With end lock) 2 uto switch model (Head end lock) (Rod end lock) 2 (Head end lock) 2 (Rod end lock) (Head end lock) (Rod end lock) (Head end lock) (Rod end lock) (Head end lock) (Rod end lock) (Head end lock) (Rod end lock) (Head end lock) (Rod end lock) (Head end lock) (Rod end lock) (21.). (.) 21 (2) 1 (.) D- D- U D- D (.) 1 (31.) 1. (1.) 24 (3) D-H D-H/JW D-F/F D-J/FF D-FW/FNT U D-H/H D-3C/C D-F/J/JW D-FV/JC D-FW/FWV D-F/FV D-FF/FNT () () 21. (2.) 1. () D-3C D-C U () 1. () 2 (2) 24. (3.) (1) 4 (4) 1. (23.). () D-FV D-FWV D-FV U D-W (4). (2) () 21. (3.) U () 31. (34) () (3) (.). (.) (2) (.) D- D-V 3 (3) 3 () 3 (3). () (.) 1 (3.). (.) 23 (3) U D- D-V D-W D-WV D- D-V (1) 3. (3) () 3 (3) (24.). (.) 24 (2) 4 (2.) D-JC D-W D-V U (3) () 41 (43). (1) (.) (34.) 4. (4.) 2 (41) U (1.) 2. (2.) 1 () (.) D-V D-WV D-V D-P4DW (2.) 1 (2.). (.) (34) Note) The dimensions in parentheses for ø and ø2 are for, and mm strokes, and the dimensions in parentheses for ø and ø are for and mm strokes. djust the auto switch after confirming the operating conditions in the actual setting. pplicable Cylinder Series: CDQ2 (With end lock) uto switch model D-P4DW U arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock Water Resistant With uto Switch uto Switch ade to Order 12

159 With nd ock Series CDQ2 With uto Switch 2 2 inimum Stroke for uto Switch ounting pplicable Cylinder Series: CDQ2 (With end lock) Number of auto switches With 1 pc. With 2 pcs. D-V D-FV D-JC D-V D- D- D-3C D-C D- D-WV D-V D-FWV D-FV 1 D- D-W D- D-H D-H D-F D-J 1 1 D-W 1 D-FW D-JW D-F D-FF D-FNT D-P4DW Operating Range pplicable Cylinder Series: CDQ2 (With end lock) uto switch model D-(V) D-(V) D-W(V) D-(V) (.) (.) (.) () () (.).. (.) D-(H)(C) D-(H)(C) D-W D-F(V) 1 1 D-J(C) D-FW(V) D-F(V).. D-FNT D-FF D-P4DW. Values which include hysteresis are for guideline purposes only, they are not a guarantee (assuming approximately ±3% dispersion) and may change substantially depending on the ambient environment. The values for ø or more of the D-(V)/(V)/W(V)/(V) types indicate the operating range when the conventional switch installation groove is attached without using the auto switch mounting bracket Q2-. The values in parentheses for ø or more of the D-(V)/(V)/W(V)/(V) types indicate the operating range when the auto switch mounting bracket Q2- is used. (.) (). (.) (). ()

160 Compact Cylinder: With nd ock Series CDQ2 4 uto Switch ounting rackets/part No. pplicable Cylinder Series: CDQ2 (With end lock) uto switch mounting surface ø, ø2 ø, ø, ø ø, ø, ø Port side Port side Port side arge ore C C C uto switch model uto switch mounting surface Port///C side Port side uto switch mounting surface //C side uto switch mounting surface Port///C side ong Stroke D- D-V D- D-V D-W D-WV D- D-V uto switch mounting brackets are not required. uto switch mounting brackets are not required. Q-2 Q2- Two kinds of auto switch brackets are used as a set. Set screw (Not used) uto switch mounting brackets are not required. Rod xial Piping Note 1) When a compact auto switch is mounted on the three sides (, and C above) other than the port side of ø to ø cylinders, auto switch mounting brackets shown above are required. Order them separately from cylinders. (The above is also applicable when a compact auto switch is mounted using an auto switch mounting rail, but not using a compact auto switch installation groove for ø to ø cylinders.) Ordering example CDQ2-D-W 1 pc. Q-2 2 pcs. Q2-2 pcs. Note 2) When shipping cylinders, auto switch mounting brackets and auto switches are shipped together. nti-lateral oad With nd ock uto switch model D-/ D-3C/C D-H/H D-W D-F/J D-FV D-JC D-FW/JW D-FWV D-F/FV D-FF/FNT D-P4DW Q-2 QP1- Note 3) When shipping cylinders, auto switch mounting brackets and auto switches are shipped together. Note 4) Refer to pages to 2 in est Pneumatics No. 2 for further information on auto switch mounting method. [Stainless Steel ounting Screw Kit] The following stainless steel mounting screw kit (with nuts) is available. Use it in accordance with the operating environment. (Since auto switch spacer (for Q- 2) is not included, order Q-2 separately.) 2: For D-//F/J types The above stainless steel mounting screws are used when a cylinder is shipped with the D-F/FV auto switches. When only an auto switch is shipped independently, 2 is attached. Note ) Refer to page 1 in est Pneumatics No. 2 for details of 2. Note ) When the D-(V) type is mounted on a port side other than ø, ø or ø, order auto switch mounting brackets Q2-S, Q-2 or the stainless steel mounting screw kit 2 separately. uto Switch ounting racket/weight ounting bracket part no. Q-2 Q2- QP1- Weight (g) 1. Water Resistant With uto Switch uto Switch ade to Order

161 With nd ock Series CDQ2 With uto Switch 3 Other than the applicable auto switches listed in How to Order, the following auto switches are mountable. Refer to est Pneumatics No. 2 for detailed specifications. pplicable Cylinder Series: CDQ2 (With end lock) uto switch type odel lectrical entry D-3 Grommet (Perpendicular) D- Reed D-3H, H Grommet (In-line) D-H D-FNV, FPV, FV D-FNWV, FWV Grommet (Perpendicular) D-FV D-F, FP, J Solid state D-FW, FPW, JW Grommet (In-line) D-F D-FNT D-PDW Grommet (In-line) Features Without indicator light Without indicator light Diagnostic indication (2-color indication) Water resistant (2-color indication) Diagnostic indication (2-color indication) Water resistant (2-color indication) With timer agnetic field resistant (2-color indication) pplicable bore size ø to ø ø to ø ø to ø With pre-wired connector is also available for solid state auto switches. For details, refer to est Pneumatics No. 2. Normally closed (NC = b contact) solid state auto switches (D-FG/FH) are also available. For details, refer to est Pneumatics No. 2. When using a magnetic field resistant solid state auto switch D-P3DW type, please contact SC separately. (pplicable bore size: ø to ø) Heat resistant solid state auto switch (D-FNJ) is not applicable. Regarding the D-PDW, please contact SC separately. 1

162 Without auto switch ø, ø2 Without auto switch ø to ø With auto switch F G D With auto switch (uilt-in magnet) Through-hole () oth ends tapped Foot Rod flange Head flange Double clevis Compact Cylinder: Water Resistant Double cting, Single Rod Series CQ2 ø, ø2, ø, ø, ø, ø, ø, ø CQ2 CQ2 CDQ2 ounting (ø to ø) (ø to ø) ounting brackets are shipped together, (but not assembled). Cylinder mounting bolts are not included. Order them separately referring to ounting olt for C(D)Q2 on pages 1 and. 2 mm 2 mm mm mm mm mm mm mm R 3 D R 3 D Port thread type Nil TN TF thread Rc NPT G How to Order R Z 3 D Z uto switch mounting groove Z ø to ø2 ø to ø ody option Nil ction D Double acting Cylinder stroke For Strokes, refer to the next page. Number of auto switches Nil S n 2 pcs. 1 pc. n pcs. ade to Order Refer to the next page for details. uto switch Nil Without auto switch Refer to the below table for applicable auto switches. 2 surfaces 4 surfaces (Rod end female thread) arge ore ong Stroke Rod xial Piping nti-lateral oad With nd ock uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) CDQ2R-2DZ pplicable uto Switches/Refer to pages to 1 in est Pneumatics No. 2 for further information on auto switches. Type Special function lectrical entry Indicator light Wiring (Output) Water resistant cylinder R V oad voltage DC NR seal (Nitrile rubber) FK seal (Fluororubber) C uto switch model Perpendicular In-line ead wire length (m). (Nil) 1 () 3 () (Z) Pre-wired connector pplicable load Water Resistant With uto Switch Solid state auto switch Water resistant (2-color indication) Grommet Yes 3-wire (NPN) 3-wire (PNP) 2-wire 24 V V, V V NV PV V N P IC circuit Relay, PC uto Switch ead wire length symbols:. m Nil (xample) 1 m (xample) 3 m (xample) m Z (xample) Z For details about auto switches with pre-wired connector, refer to pages 1 and 1 in est Pneumatics No. 2. Solid state auto switches marked with are produced upon receipt of order. ade to Order

163 Series CQ2 Specifications 2 JIS Symbol Double acting, Single rod ction Fluid Proof pressure aximum operating pressure inimum operating pressure mbient and fluid temperature ubrication Piston speed llowable kinetic energy (J) Stroke length tolerance Double acting, Single rod ir 1. Pa 1. Pa. Pa Without auto switch: to C (No freezing) With auto switch: to C (No freezing) Not required (Non-lube) to mm/s mm Strokes ade to Order (For details, refer to pages 1 to.), 2,,,, stroke,, 1,, 2, 3, 3,, 4,,, 1,, 2, 3, 3,, 4,,,, 1,, 2, 3, 3,, 4,,, Symbol Specifications Piston rod/retaining ring/rod end nut -C material: Stainless steel anufacture of Intermediate Strokes Refer to pages to 1 for the specifications of cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height inimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Type Part no. Description Stroke range xample spacer is installed in the standard stroke body. Refer to How to Order for the standard model number. (P. ) Strokes in 1 mm intervals are available by installing a spacer in the standard stroke cylinder., 2 to Part no.: CQ2R-DZ CQ2R-DZ with 1 mm width spacer inside The dimension is. mm. Stroke range 1 to 4 1 to Type Pneumatic ounting Piping Through-hole () oth ends tapped uilt-in magnet Pipe thread TN TF 2 x. x. Note) x. Rc1/ NPT1/ G1/ Rc1/ Rc1/4 Rc1/4 Rc3/ Rc3/ NPT1/ NPT1/4 NPT1/4 NPT3/ NPT3/ G1/ G1/4 G1/4 G3/ G3/ Note) ø without auto switch: x. is used for mm stroke piping dimension. Thus, do not enter a symbol for the port thread type. 1