Series RSQ (Fixed mounting height) Series RSG (Adjustable mounting height)

Size: px
Start display at page:

Download "Series RSQ (Fixed mounting height) Series RSG (Adjustable mounting height)"

Transcription

1 Stopper Cylinder Series RSQ (Fixed mounting height) ø12, ø, ø, ø, ø, ø Series RSG (djustable mounting height) ø, ø Realise Labour Saving and utomation of Conveyor Line through hole style and a both ends tapped style are available. Series RSQ (Fixed mounting height) ø12, ø, ø, ø, ø, ø ounting position can be adjusted by vailable Styles It is possible to select options for many applications. Style: Fixed mounting height (RSQ), djustable mounting height (RSG) ction: Double acting, Single acting (spring extend), Double acting with spring Rod end configuration: Round bar, Non-rotating, Roller, Lever ounting: Through hole, oth ends tapped Flange: (RSG) uto Switch Option vailable Compact auto switch mounting to enable miniaturization of machines and designs. Locking mechanism changing the attached flange height. Series RSG (djustable mounting height) ø, ø (υm/min) quipped with an easy-tomaintain shock absorber. The shock absorber incorporated in the lever style is adjustment-free and easy-to-maintain. (ø, ø, ø) Lever style selected accord-ing to applications Prevention of repulsion by light pallets Locking mechanism Partial passing of work With cancel cap K/K2 RSRSH R RC C..X TS C..S Q RHC CC Work (mkg) Work (mkg) Work (mkg) Cancel cap (mechanism to hold lever horizontally) Lever Pin racket PSS (υm/min) PSS (mkg) (mkg) Series es RSQ Series RSG Lever standard position Lever locked Lock releasing Cancel cap Variations Series ounting ction Rod end configuration agnet Locking mechanism Variations Cancel One-touch fitting ore size Standard stroke 1 2 R S Q Through hole oth ends tapped Double Double with spring Single Round bar Roller Non-rotating Fixed Lever djustable 12 R S G Flange style Double Double with spring Single Round bar Roller Non-rotating Fixed Lever djustable 1

2 Standard With auto switch With auto switch (uilt-in magnet) ounting bracket Through-hole (Standard) oth ends tapped style Note 1) Since ø12 uses a common tube for both and, only is used for part no. denotation. ore size mm mm mm mm mm mm RSQ RSDQ Port thread type thread ø12, ø Rc TN TF NPT G ø to ø F uilt-in One-touch fittings (2) How to Order Cylinder stroke 12 uilt-in agnet Cylinder odel, 1 If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) RSDQ-1D, 1,, 1,, 2,, 2, 1 1 pplicable uto Switches/Refer to uto Switch Guide for further information on auto switches. Type Reed auto switch Solid state auto switch Special function Diagnostic indication (2-colour indication) Water resistant (2-colour indication) With diagnostic output (2-colour indication) Diagnostic indication (2-colour indication) lectrical entry Grommet Connector Grommet Grommet Connector Grommet Yes No Yes No Yes Yes Indicator light Note 2) ore sizes available w/ One-touch fittings are ø to ø. D D W uto switch Without auto switch For the applicable auto switch model, refer to the table below. Rod end configuration Symbol K R L Configuration Rounde bar type Chamfered type Roller type Lever type (Non-adjustable) (4) Note ) TF for ø indicates. Lever type C (4) nergy absorbing D djustable deformation Wiring (Output) -wire (NPN) -wire (PNP) 2-wire -wire (NPN) -wire (PNP) 2-wire -wire (NPN) -wire (PNP) 2-wire 4-wire -wire (NPN equivalent) 2-wire 24 V 24 V Load voltage DC V, 12 V 12 V V, 12 V 12 V V, 12 V 12 V V,12 V V 12 V C V V V,12 V V or less 12 V V,12 V 24 V or less ction D Double acting Double acting with spring loaded T Single acting (Spring extend) uto switch model Perpendicular In-line ø12 ø, ø, ø to ø ø12 ø, ø, ø to ø NV N PV P V JC NWV NW PWV PW WV W NV 1 N 1 PV 1 P 1 V 1 1 FF V 2 V 2 V C C W 2H ade to Order Specifications For details, refer to page. Number of auto switches S Lead wire length (m). () 1 () (L) 2 pcs. 1 pc. pplication asic style With cancel cap With lock menchanism With lock & cancel Note 4) The lever types are applicable only to bore sizes ø, ø and ø. (Z) None (N) Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit 1 Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. 2 1 m type lead wire is only applicable to D-. Lead wire length symbols:. m (xample) NW Solid state auto switches marked with are produced upon receipt of order. 1 m (xample) NW m L (xample) NWL m Z (xample) NWZ None N (xample) JCN Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to uto Switch Guide. When D-(V)/(V)/W(V)/(V) types with ø to ø are mounted on a side other than the port side, order auto switch mounting brackets separately. Refer to page for details. 2 Stopper Cylinder/Fixed ounting Height Series RSQ ø12, ø, ø, ø, ø, ø Relay, PLC Relay, PLC

3 Stopper Cylinder/Fixed ounting Height Series RSQ Roller type Lever type with built-in shock absorber Round bar Symbol Specifications X Change of rod end shape XC Special port location Spring Force (Single acting) ore size 12 ade to Order Specifications xtended (N) Compressed ,. pplicable only to round bar type, chamfered type and roller type end configurations. odel ore size ounting uilt-in magnet Piping ction Rod end configuration Specifications ction Double acting, Double acting with spring loaded, Single acting (Spring extend) Fluid ir Proof pressure 1. Pa aximum operating pressure 1. Pa Without auto switch: to C mbient and fluid temperature With auto switch: to C Lubrication Not required (Non-lube) Cushion Rubber bumper +1.4 length tolerance ounting Through-hole/oth ends tapped uto switch ountable No freezing (for cylinders with or without an auto switch) ore Size/Standard ore size 12 Weight ction Double acting Single acting, Spring extend Double acting with spring loaded 12 Through-hole Note1) oth ends tapped style Screw-in type x. 1/ Note2) uilt-in One-touch fittings ø/4 ø/ Round bar Chamfered Roller type Lever type Round bar, Chamfered type, 1 ore size 12, 1,, 2, Rod end configuration Double acting, Single acting (Spring extend), Double acting with spring loaded Note 1) ø12 tubes can have both through-hole and tap mountings in the same tube. Note 2) TF (G thread) for ø indicates x.. Rod end configuration Roller type, 1, 1,, 2, Round bar, Chamfered, Roller Round bar, Chamfered, Roller Round bar, Chamfered, Roller Round bar, Chamfered, Roller Lever with built-in shock absorber Round bar, Chamfered, Roller Lever with built-in shock absorber Round bar, Chamfered, Roller Lever with built-in shock absorber Lever type with shock absorber, 1,, 2, Cylinder stroke (kg) K/K2 RSRSH R RC C..X TS C..S Q RHC CC

4 Series RSQ ounting olt for RSQ ounting method: ounting bolt for through-hole mounting style of RSQ is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. xample) CQ-x4L 2 pcs. D C ounting bolt Cylinder model C D ounting bolt part no. Cylinder model C D ounting bolt part no. RSQ12- Note) 4 CQ- x 4L RSQ- CQ- x L RSQ- CQ- x L -2. CQ- x L. -1 x L - x L RSQ- CQ- x L RSQ- CQ- x L -1 x L -2 x L - x L - x L RSQ- CQ- x L -1 x L - x L Note) e sure to use the attached flat washers when mounting ø12 cylinders with through-holes. Operating Ranges by Rod nd Configuration (xample 1) For roller type with transfer speed of 1 m/min. and the weight of transferred object of kg. <How to read the graphs> To select a cylinder based on the specifications above, find the intersection of the speed of 1 m/min. on the horizontal axis and the weight of kg on the vertical axis in graph (1) below, and select RSQ-R that falls in the cylinder operating range. (xample 2) Transfer speed of 1 m/min., Weight of transferred object of kg, Friction coefficient μ =.1, Lever type (Lever type with lock mechanism) <How to read the graphs> To select a cylinder based on the specifications above, find the intersection of the speed of 1 m/min. on the horizontal axis and the weight of kg on the vertical axis in graph () below, and select RSQ-D that falls in the cylinder operating range. Roller Type/Round ar Type/Chamfered Type Weight of transferred object m (kg) 4 2 ø ø ø ø ø ø12 xample 1 Graph (1) Lever Type (With shock absorber) Friction coefficient μ = Graph (2) ø ø Weight of transferred object m (kg) ø 4 2 Lever Type (With shock absorber) Friction coefficient μ =.1 Graph () ø Weight of transferred object m (kg) ø ø 4 2 xample Transfer speed υ (m/min) 1 1 Transfer speed υ (m/min) 1 1 Transfer speed υ (m/min) Lateral Load and Operating Pressure Lever-type weight of transferred object and transfer speed graphs (graphs (2) and ()) show the values at room temperature ( to 2 C). When selecting cylinders, confirm the Specific Product Precautions as well. The larger the lateral load, the higher the operating pressure required for the stopper cylinder. Set the operating pressure using the graphs as a guide. (pplicable for round bar, roller and chamfered type rod end configurations.) Operating pressure P (Pa) 1.. RSQ12 RSQ Operating pressure P (Pa) 1.. RSQ RSQ RSQ RSQ Lateral load F (N) Lateral load F (N) 4

5 Stopper Cylinder/Fixed ounting Height Series RSQ Construction Double acting Roller rod y q r! t y q!4 r e w t u!!! o u!! o ø ø, ø, u! q y!4! w t u!!4!! i t!! e o q e o ø Round bar rod end type (D) Chamfered rod end type (K) K/K2 RSRSH R RC C..X TS C..S Q RHC CC Double acting with spring loaded ø12, ø! Single acting!! ø12, ø ø, ø, ø!!1!2! ø, ø, ø Component Parts No. Description aterial Note Rod cover Cylinder tube Piston Spacer for switch Piston rod ushing Non-rotating guide umper umper Return spring lement luminium alloy luminium alloy luminium alloy luminium alloy ø12, ø, ø Stainless steel ø, ø, ø Carbon steel earing alloy Rolled steel Urethane Urethane Steel wire Sintered metallic C nodised Hard anodised Chromated ø12, ø only Hard chrome plated Non-rotating type only Zinc chromated (xcept double acting) ø to ø (Single acting only) No. Description aterial Note 12 Retaining ring Plug with fixed orifice Hexagon socket head set screw 1 Hexagon socket head set screw agnet 1 Hexagon socket head cap screw 1 Rod seal 1 Gasket Piston seal 21 Roller 22 Spring pin Carbon tool steel ø to ø (Single acting only) lloy steel ø12, ø only (Single acting only) Chromium molybdenum steel xcept ø12 Chromium molybdenum steel Non-rotating type only lloy steel ø12 only NR NR NR Resin Carbon tool steel

6 Series RSQ uilt-in shock absorber Lever rod end type (Fixed) (ø, ø, ø only) Lever rod end type (With lock mechanism and cancel cap) (ø, ø, # $ $ $4 # @ # # # # #4 #2 # $ Only one roller is provided for ø. Component Parts No. Description aterial Note Lever Lever holder Roller Shock absorber Lever spring Type C retaining ring for axis Lever pin Roller pin Steel balls Cast iron Rolled steel Resin Stainless steel wire Carbon tool steel Carbon steel Carbon steel High carbon chrome bearing steel Hexagon socket head set screw Chromium molybdenum steel Hexagon socket head set screw Chromium molybdenum steel 4 One-side tapered pin Carbon steel Replacement Parts/Seal Kit Kit no. ore size Double acting with Double acting spring loaded Single acting 12 RSQ12D-PS RSQ12T-PS RSQD-PS RSQ-PS RSQT-PS RSQD-PS RSQ-PS RSQT-PS RSQD-PS RSQ-PS RSQT-PS RSQD-PS RSQ-PS RSQT-PS RSQD-PS RSQ-PS RSQT-PS ø-r-x22 ø, -R1-X2 Contents Set of above Seal kit Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) No. Description aterial Note racket Pin Spacer Round head Phillips screw Pin racket spring Carbon steel Carbon steel Carbon steel Rolled steel Rolled steel Steel wire 41 Hexagon socket head set screw Chromium molybdenum steel 42 4 Spring washer Urethane ball Steel wire Urethane 44 Hexagon socket head set screw Chromium molybdenum steel 4 4 djustment bolt Cancel cap earing steel luminium alloy Replacement Parts: Shock bsorber ore size Kit no. R-X22, R1-X2

7 I Stopper Cylinder/Fixed ounting Height Series RSQ Rod nd Configuration: Round ar Type asic style: Through-hole mounting, Screw mounting These figures show the piston rod extended. ore size: ø12 1 øt ød RSQ12-4 x. depth of counterbore 4 depth 1 4 x 4 x. effective depth ore size: ø, ø.1 RSQ Q.1 ø ø 2 x x x P (Rc, NPT, thread) F 2 x øn through 4 x O depth of counterbore Screw mounting style: oth ends tapped style RSQ odel øn through-hole O1 thread RSQ 41. RSQ 4 RSQ 4 RSQ 2. RSQ 4 R R + uto switch inimum lead wire bending radius 4 x ø. through Flat washer 4 parts. ounting bolt for rod cover 2 parts Y N.. O1 4 x. x 1 x 1 x 1 x 1.2 R Dimensions other than above are the same as below drawings. ø 2 x. depth of counterbore 4 depth x 4 x. effective depth K/K2 RSRSH R RC C..X TS C..S Q RHC CC V H stroke RSQ - 2 x P (Rc, NPT, G) Q F ore size: ø, ø, ø Z øt.1 ød J ore size.. 2 V H stroke uilt-in One-touch fittings (ø to ø) Tubing O.D. ø ø D ø F. H I J 4. Note 1) thread ( x.) is applicable for ø12 and ø piping ports. TF (G thread) for ø also indicates x.. Note 2) For the auto switch mounting position and its mounting height, refer to page. Q ø to ø 2 4 N.. Tubing O.D. øq F øq QU O. depth 4 depth depth depth 11 depth 4 x øn through x O depth of counterbore QU QW P x. 1/ 1/ 1/ / 1 uilt-in One-touch Fittings ore size Q pplicable tubing O.D. Q T F Q Q QU QW V Y 4 42 Note ) These figures show the piston rod extended. Note 4) In the case of single acting type, a One-touch fitting is on the rod side only.. 2 Z 1

8 SC Series RSQ Rod nd Configuration: Chamfered (Non-rotating piston rod) asic style: Through-hole mounting, Screw mounting These figures show the piston rod extended. ore size: ø12 RSQ12-K 4 x. depth of counterbore 4 depth 1.1 ø Workpiece transfer direction ø 2. 2 x x. 1. Screw mounting style: oth ends tapped style RSQ odel N øn through-hole O1 thread RSQ 41.. RSQ RSQ RSQ RSQ R R + uto switch inimum lead wire bending radius 4 x ø. through Flat washer 4 parts O1 4 x. x 1 x 1 x 1 x 1.2 R Dimensions other than above are the same as below drawings. ø 2 x. depth of counterbore 4 depth ore size: ø, ø 4 x 4 x. effective depth RSQ -K Workpiece transfer direction Q F. 2 x P (Rc, NPT, thread) ounting bolt for rod cover 2 parts 2 x øn through 4 x O depth of counterbore 1 2 Y 2 x 4 x. effective depth øt ød G V H stroke ore size: ø, ø, ø Workpiece transfer direction RSQ -K Q 2 x P (Rc, NPT, G) F J Z I øt.1 G ød.1 uilt-in One-touch fittings (ø to ø) ore size.. 2 ø Tubing O.D. ø D ø F. V H stroke G 4 Note 1) thread ( x.) is applicable for ø12 and ø piping ports. TF (G thread) for ø also indicates x.. Note 2) For the auto switch mounting position and its mounting height, refer to page. H I Q J 4. Tubing O.D. øq 2 4 F ø to ø N.. øq QU QW O. depth 4 depth depth depth 11 depth uilt-in One-touch Fittings ore size P x. 1/ 1/ 1/ / 1 pplicable tubing O.D. Q Q T x øn through x O depth of counterbore F Q Q QU QW V Y 4 42 Note ) These figures show the piston rod extended. Note 4) In the case of single acting type, a One-touch fitting is on the rod side only.. 2 Z 1

9 SC Stopper Cylinder/Fixed ounting Height Series RSQ Rod nd Configuration: Roller Type asic style: Through-hole mounting, Screw mounting These figures show the piston rod extended. ore size: ø ore size: ø, ø RSQ12-R 4 x ø. depth of counterbore 4 depth Workpiece transfer direction.1 øt 4 x 4 x. effective depth øs ød G RSQ Workpiece transfer direction.1 ø 2. ø -R Q ø x P (Rc, NPT, thread) F 2 x øn through 4 x depth of counterbore Screw mounting style: oth ends tapped style RSQ odel øn through-hole O1 thread RSQ 41. RSQ 4 RSQ 4 RSQ 2. RSQ 4 R R + uto switch 2 x x. inimum lead wire bending radius x ø. through Flat washer 4 parts X Y N.. O1 4 x. x 1 x 1 x 1 x 1.2 R Dimensions other than above are the same as below drawings. ø. ounting bolt for rod cover 2 parts 2 x. depth of counterbore 4 depth x 4 x. effective depth K/K2 RSRSH R RC C..X TS C..S Q RHC CC L V H stroke ore size: ø, ø, ø RSQ R Workpiece transfer direction S Q 2 x P (Rc, NPT, G) F J Z X I øt.1 ød G V H stroke 4 x øn through x O depth of counterbore uilt-in One-touch fittings (ø to ø) ore size Tubing O.D. ø ø D F. G 4 H 2. I J 4. Note 1) thread ( x.) is applicable for ø12 and ø piping ports. TF (G thread) for ø also indicates x.. Note 2) For the auto switch mounting position and its mounting height, refer to page. ø Q L Tubing O.D. øq F øq ø to ø 2 4 N.. QU O. depth 4 depth depth depth 11 depth QW P x. 1/ 1/ 1/ / 1 uilt-in One-touch Fittings ore size Q S pplicable tubing O.D. Q T F Q Q QU QW.. V X. 4 Y 4 42 Note ) These figures show the piston rod extended. Note 4) In the case of single acting type, a One-touch fitting is on the rod side only.. 2 Z 1

10 Series RSQ Rod nd Configuration: Lever Type with Shock bsorber asic style: Through-hole mounting, Screw mounting These figures show the piston rod extended. ore size: ø RSQ-L Screw mounting style: oth ends tapped style RSQ øn through-hole O1 thread odel RSQ RSQ RSQ N. R R + O1 x 1 x 1 x 1.2 R Dimensions other than above are the same as below drawings. Workpiece transfer çdirection 4. 2 x (Rc 1/, NPT 1/, G 1/)..1 ø ø R2. ø1 ore size: ø, ø I 1.. Z RSQ x ø through x ø depth of counterbore depth stroke Workpiece transfer çdirection J -L 2 x (Rc 1/, NPT 1/, G 1/) øt ø2 R. ø 24 2 x øn through x O depth of counterbore stroke uilt-in One-touch fittings øq Tubing O.D. øq F Q ore size QU QW I J N. O depth 11 depth Note 1) For the auto switch mounting position and its mounting height, refer to page. Note 2) These figures show the piston rod extended. Note ) In the case of single acting type, a One-touch fitting is on the rod side only. T 44 Z 1 uilt-in One-touch Fittings ore size pplicable tubing O.D. Q F Q Q QU QW

11 R Stopper Cylinder/Fixed ounting Height Series RSQ Rod nd Configuration: Lever Type with Shock bsorber Variable energy absorbing type/ Through-hole mounting, Screw mounting style djustable shock absorber stroke These figures show the piston rod extended. ore size: ø Workpiece transfer direction ore size: ø, ø RSQ- 4 x ø through x depth of counterbore depth Workpiece transfer direction I 4 4 RSQ 2 x (Rc 1/, NPT 1/, G 1/). djustment bolt x (Rc 1/, NPT 1/, G 1/) Z. djustment bolt J 4 + Screw mounting style: oth ends tapped style RSQ øn through-hole O1 thread odel RSQ RSQ RSQ N. R R O1 x 1 x 1 x 1.2 R Dimensions other than above are the same as below drawings.. ø1 ø ø R2.. ø øt.1 ø2 24 K/K2 RSRSH R RC C..X TS C..S Q RHC CC 4 x øn through x O depth of counterbore stroke + With cancel cap RSQ-C Dimensions when equipped with cancel cap are the same as the drawing above. Cancel cap These figures show dimensions when set for maximum energy absorbing capacity. ore size I J N. O depth 11 depth Note 1) For the auto switch mounting position and its mounting height, refer to page. Note 2) These figures show the piston rod extended. Note ) In the case of single acting type, a One-touch fitting is on the rod side only. Note 4) The figures show the dimensions when the adjustment bolt is lowered (when energy absorption is at its maximum). However, these dimensions change within the ranges shown below as the adjustment bolt is raised (energy absorption is reduced). ø,., ø, 24,. 11., T 44 Z 1 11

12 R2 Series RSQ Rod nd Configuration: Lever Type with Shock bsorber Variable energy absorbing type/ Through-hole mounting, Screw mounting style With lock mechanism These figures show the piston rod extended. Screw mounting style: oth ends tapped style RSQ øn through-hole O1 thread odel RSQ RSQ RSQ N. R R + O1 x 1 x 1 x 1.2 R Dimensions other than above are the same as below drawings. ore size: ø RSQ-D Workpiece transfer direction djustment bolt 4. 2 x (Rc 1/, NPT 1/, G 1/)..1 ø. ø1 ore size: ø, ø RSQ -D stroke Z I J. 4 4 ø 4 x ø through x ø depth of counterbore depth 4 4 Workpiece transfer direction. 1. djustment bolt 2 x (Rc 1/, NPT 1/, G 1/) ø ø2 øt R 24 4 x øn through x O depth of counterbore stroke With lock mechanism + Cancel cap RSQ- Dimensions when equipped with lock and cancel cap are the same as the figure drawing. Cancel cap Cancel cap These figures show dimensions when set for maximum energy absorbing capacity. ore size I J N. O depth 11 depth Note 1) For the auto switch mounting position and its mounting height, refer to page. Note 2) These figures show the piston rod extended. Note ) In the case of single acting type, a One-touch fitting is on the rod side only. Note 4) The figures shows the dimensions when the adjustment bolt is lowered (when energy absorption is at its maximum). However, these dimensions change within the ranges shown below as the adjustment bolt is raised (energy absorption is reduced). ø,., ø, 24,. 11., 12 T 44 Z 1

13 K/K2 RSRSH R RC C..X TS C..S Q RHC CC

14 Series RSQ uto Switch ounting 1 uto Switch Proper ounting Position (Detection at nd) and Its ounting Height ø12 D- D- D-W D- D-V D-V D-WV D-V Hs D- D- D-W D-V D-V D-WV D- D-V ø, Hs 2 D- D- D-H D-H D-F D-J D-FW D-JW D-FF D-FNT D-F D-C D-C D-JC D-W D-FWV D-FV D-FV ø, ø ø to ø Hs Hs ø to ø D- D- D-W D- D-V D-V D-WV D-V Hs

15 uto Switch ounting Series RSQ uto Switch Proper ounting Position (Detection at nd) and Its ounting Height uto Switch Proper ounting Position uto switch model ore size D- D-V D- D-V D-W D-WV D- D-V D- D- D-2/H/H D-C/C D-F/J D-FV/JC D-FV/F D-FW/JW D-FWV/FF D-FNT D-W Note) djust the auto switch after confirming the operating conditions in the actual setting. uto Switch ounting Height uto switch model ore size D-V Hs D-V D-WV D-V Hs D- D- Hs D-H D-H/F D-J/FW D-F D-JW D-FF D-FNT Hs D-C D-C Hs D-FV D-FWV D-FV Hs D-JC Hs D-W Hs Operating Range uto switch model D-/V ore size D-/V D-W/WV D-/V D-/ D-H/H D-C/C D-W D-F/J D-FV/JC D-FW/JWV D-F/FV D-FF/FNT Since this is a guideline including hysteresis, not meant to be guaranteed. (ssuming approximately ±% dispersion) There may be the case to change substantially depending on an ambient environment. The values above for a bore size ø12 and over ø of D-(V)/(V)/W(V)/ (V) types are measured when the conventional switch installation groove is attached without using the auto switch mounting bracket Q

16 Series RSQ uto Switch ounting 2 uto Switch ounting racket: Part No. uto switch mounting surface ore size ø12 ø, ø ø, ø, ø Port side Port side C C uto switch model uto switch mounting surface,, C side uto switch mounting surface Only auto switch mounting rail surface Port side uto switch mounting surface,, C side D- D-V D- D-V D-W D-WV D- D-V uto switch mounting brackets are not required. qq-1 wq2-12 Two kinds of auto switch mounting brackets are used as a set. q w Set screw (not used) uto switch mounting brackets are not required. qq-2 wq2-12 Two kinds of auto switch mounting brackets are used as a set. q w Set screw (not used) Note 1) For each cylinder series, when a compact auto switch is mounted on the three sides (, and C above) other than the port side of bore sizes ø to ø, the auto switch mounting brackets above are required. Order them separately from cylinders. Ordering example: RSDQ--W...1 unit Q pcs. Q pcs. Note 2) uto switch mounting brackets and auto switches are shipped together with cylinders. uto switch model D-/ D-C/C D-H/H D-W D-F/J D-FV D-JC D-FW/JW D-FWV D-F/FV D-FF/FNT ore size Q-1 Q-2 Note ) uto switch mounting brackets and auto switches are shipped together with cylinders. esides the models listed in How to Order, the following auto switches are applicable. Other pplicable uto Switches/Refer to the uto Switch Guide for detailed auto switch specifications. [ounting screw set made of stainless steel] The following set of mounting screws made of stainless steel (including nuts) is available. Use it in accordance with the operating environment. (Please order Q-2 separately, since auto switch spacers (for Q-2) are not included.) 2: For D-//F/J types D-F/FV auto switches are set on the cylinder with the stainless steel screws above when shipped. When an auto switch is shipped independently, 2 is attached. Note 4) When D-(V) type is mounted on a side other than the ø, ø or ø port side, order auto switch mounting brackets Q2-12S or Q-2, or a stainless steel screw set 2 separately. Note ) Refer to the uto Switch Guide for the details of 2. uto Switch ounting racket Weight uto switch mounting bracket part no. Q-1 Q-2 Q2-12 Weight (g) uto switch type odel lectrical entry (Fetching direction) Features Reed D- Grommet (Perpendicular) D- Without indicator light D-H, H Grommet (In-line) D-H Without indicator light D-FNV, FPV, FV D-FNWV, FWV Grommet (Perpendicular) Diagnostic indication (2-colour indication) D-FV Water resistant (2-colour indication) Solid state D-F, FP, J D-FW, FPW, JW Diagnostic indication (2-colour indication) Grommet (In-line) D-F Water resistant (2-colour indication) D-FNT With timer For solid state auto switches, auto switches with a pre-wired connector are also available. Refer to the uto Switch Guide for details. Normally closed (NC = b contact), solid state switch (D-FG/FH types) are also available. Refer to the uto Switch Guide for details. D-//F/J cannot be mounted on ø12.

17 With auto switch With auto switch (uilt-in magnet) RSG RSDG uilt-in agnet Cylinder odel If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch. (xample) RSDG-2D Stopper Cylinder/djustable ounting Height Series RSG ø, ø Grommet Connector Grommet 24 V How to Order V, 12 V 12 V V, 12 V 12 V V, 12 V 12 V V, 12 V D D W pplicable uto Switches/Refer to the uto Switch Guide for further information on auto switches. Type Reed auto switch Solid state auto switch Special function TN TF F Diagnostic indication (2-colour indication) Water resistant (2-colour indication) With diagnostic output (2-colour indication) ore size mm mm Port type Rc NPT G uilt-in One-touch fittings lectrical entry Cylinder stroke,, 2, Indicator light Yes Yes No Yes No D T Wiring (Output) -wire (NPN) -wire (PNP) 2-wire -wire (NPN) -wire (PNP) 2-wire -wire (NPN) -wire (PNP) 2-wire 4-wire (NPN) -wire (NPN equivalent) ction Double acting Double acting with spring loaded Single acting (Spring extend) Load voltage DC C Perpendicular In-line NV PV V NWV PWV WV NV 1 PV 1 V 1 Number of auto switches 2 pcs. S 1 pc. uto switch Without auto switch For the applicable auto switch model, refer to the table below. N P HC NW PW W N 1 P 1 1 HNF C Rod end configuration Symbol K R L Configuration Round bar type Chamfered type Roller type Lever type (Non-adjustable) pplication asic style Lever type C With cancel cap nergy absorbing D djustable deformation With lock menchanism With lock & cancel uto switch model Lead wire length (m). () 1 () (L) (Z) None (N) ade to Order Specifications For details, refer to page 1. uto switch mounting bracket Note) Note) This symbol is indicated when the D- or type auto switch is specified. This mounting bracket does not apply to other auto switches (D-C and H, etc.) () Pre-wired connector None N (xample) HCN Since there are other applicable auto switches than listed, refer to page 2 for details. For details about auto switches with pre-wired connector, refer to the uto Switch Guide. D-//W auto switches are shipped together (not assembled). (Only auto switch mounting brackets are assembled before shipped.) pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit IC circuit V V Grommet V V 12 V V or less V Relay, 2-wire 24 V CC PLC Connector 12 V 24 V or less CC 1 Water resistant type auto switches can be mounted on the above models, but in such case SC cannot guarantee water resistance. Consult with SC regarding water resistant types with the above model numbers. 2 1 m type lead wire is only applicable to D-. Lead wire length symbols:. m (xample) NW Solid state auto switches marked with are produced upon receipt of order. 1 m (xample) NW m L (xample) NWL m Z (xample) NWZ Relay, PLC 1 K/K2 RSRSH R RC C..X TS C..S Q RHC CC

18 Series RSG odel Round bar type Lever type with built-in shock absorber Spring Force (Single acting) Symbol Specifications -X Change of rod end shape -XC Special port position Roller type (N) ore size, xtended. Compressed 2. For Round bar type, Chamfered type and Roller type. ade to Order Specifications ounting uilt-in magnet Piping ction Specifications ore size Flange Screw-in type Rc 1/ uilt-in One-touch fittings ø/4 ø/ Double acting, Single acting (Spring extended), Double acting with spring loaded Round bar type Chamfered type Rod end configuration Roller type Lever type ction Double acting, Double acting with spring loaded, Single acting (Spring extended) Fluid ir Proof pressure 1. Pa aximum operating pressure 1. Pa Without auto switch: to C mbient and fluid temperature With auto switch: to C Lubrication Not required (Non-lube) Cushion Rubber bumper +1.4 length tolerance ounting Flange style No freezing (for cylinders with or without an auto switch) ore Size/Standard ore size Rod end configuration Round bar type, Chamfered type, Roller type, Lever type with shock absorber, 2,, 2, Weight (kg) ction Double acting Single acting, Spring extend Double acting with spring loaded ore size Rod end configuration Round bar type, Chamfered type, Roller type Lever type with built-in shock absorber Round bar type, Chamfered type, Roller type Lever type with built-in shock absorber Cylinder stroke

19 Stopper Cylinder/djustable ounting Height Series RSG Operating Ranges by Rod nd Configuration (xample 1) For roller type with transfer speed of 1 m/min. (xample 2) Transfer speed of 1 m/min., Weight of transferand the weight of transferred object of kg. red object of kg, Friction coefficient μ =.1, Lever type (Lever type with lock mechanism) <How to read the graphs> To select a cylinder based on the specifications above, find the intersection of the speed of 1 m/min. on the horizontal axis and the weight of kg on the vertical axis in graph (1) below, and select RSG-R that falls in the cylinder operating range. Roller Type/Round ar Type/ Chamfered Type Weight of transferred object m (kg) 4 2 ø ø xample 1 Graph (1) Lever Type (With shock absorber) Friction coefficient μ = Weight of transferred object m (kg) 4 2 ø ø <How to read the graphs> To select a cylinder based on the specifications above, find the intersection of the speed of 1 m/min. on the horizontal axis and the weight of kg on the vertical axis in graph () below, and select RSG-D that falls in the cylinder operating range. Graph (2) Lever Type (With shock absorber) Friction coefficient μ =.1 Weight of transferred object m (kg) 4 2 ø ø xample 2 Graph () K/K2 RSRSH R RC C..X TS C..S Q RHC CC Transfer speed υ (m/min) Transfer speed υ (m/min) Transfer speed υ (m/min) Lateral Load and Operating Pressure The larger the lateral load, the higher the operating pressure required for the stopper cylinder. Set the operating pressure using the graphs as a guide. (pplicable for round bar, roller and chamfered type rod end configurations.) Lever-type weight of transferred object and transfer speed graphs (graphs (2) and ()) show the values at room temperature ( to 2 C). When selecting cylinders, confirm the Specific Product Precautions as well. Operating pressure P (Pa) Lateral load F (N) 1

20 Series RSG Construction Roller r y o t!!!!4! i q!! w!2!1 Lever rod end with shock absorber # Lever rod end type (With lock mechanism and cancel cap) $ $ $4 # $1 $2 @ # # # # $ Round bar rod end type (D) Chamfered rod end type #4 #2 # $ Component Parts No Description aterial Note Tube cover Head cover Piston Piston rod ushing Non-rotating guide umper umper luminium alloy luminium alloy luminium alloy Carbon steel earing alloy Rolled steel Urethane Urethane Hard anodised nodised Chromated Hard chrome plated Use collar for round bar type. Hexagon socket head set screw Chromium molybdenum steel Return spring Retaining ring lement Lock nut Flange Steel wire Carbon tool steel Sintered matallic C Carbon steel Cast iron Zinc chromated (xcept double acting) (Single acting only) (Single acting only) Hexagon socket head set screw Chromium molybdenum steel all agnet Rod seal Gasket Piston seal Resin NR NR NR Used Only for double acting and double acting with spring loaded. Replacement Parts/Seal Kit ore size Kit no. Double acting with Double acting spring loaded Single acting RSGD-PS RSGD-PS RSG-PS RSG-PS RSGT-PS RSGT-PS Contents Set of above Seal kit Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S- ( g) Component Parts (For single acting) No. Description aterial Note Roller type 21 Roller Resin 22 Spring pin Carbon tool steel Lever type 2 Lever Cast iron 24 Lever holder Rolled steel 2 Roller Resin 2 Shock absorber R1-X2 2 Lever spring Stainless steel wire 2 Type C retaining ring for shaft Carbon tool steel 2 Lever pin Carbon steel Roller pin Carbon steel 1 Steel balls High carbon chrome bearing steel Hexagon socket head set screw Chromium molybdenum steel Hexagon socket head set screw Chromium molybdenum steel 4 One-side tapered pin Carbon steel With lock mechanism racket Carbon steel Pin Carbon steel Spacer Carbon steel Round head Phillips screw Rolled steel Pin Rolled steel racket spring Steel wire 41 Hexagon socket head cap set screw Chromium molybdenum steel 42 Spring washer Steel wire 4 Urethane ball Urethane 44 Hexagon socket head cap set screw Chromium molybdenum steel 4 djustment bolt earing steel With cancel cap 4 Cancel cap luminium alloy Replacement Parts: Shock bsorber ore size Kit no., R1-X2

21 Stopper Cylinder/djustable ounting Height Series RSG Rod nd Configuration: Round ar Type asic style: Flange mounting These 2 figures show the piston rod extended. ore size: ø, ø RSG- K/K2 (2 + ) RSRSH 4 x 1. (12) 2 ø. (Rc 1/, NPT 1/, G 1/) (Rc 1/, NPT 1/, G 1/) Workpiece transfer direction R RC C..X ø2 ø.1 TS C..S Q stroke.1 4 x ø through RHC CC uilt-in One-touch fittings øq Tubing O.D. øq QV ore size 4 Q Q QV. Note 1) In the case of single acting type, a One-touch fitting is on the rod side only. Note 2) These figures show the piston rod extended. Note ) For the auto switch mounting position and its mounting height, refer to page 2. 21

22 Series RSG Rod nd Configuration: Chamfered Type (Non-rotating piston rod) asic style: Flange mounting These 2 figures show the piston rod extended. ore size: ø, ø RSG-K (2 + ) 4 x 1. (12) 2 ø. (Rc 1/, NPT 1/, G 1/) (Rc 1/, NPT 1/, G 1/) ø2 ø Workpiece transfer direction stroke.1 4 x ø through uilt-in One-touch fittings øq Tubing O.D. øq QV ore size 4 Q Q QV. Note 1) In the case of single acting type, a One-touch fitting is on the rod side only. Note 2) These figures show the piston rod extended. Note ) For the auto switch mounting position and its mounting height, refer to page 2. 22

23 Stopper Cylinder/djustable ounting Height Series RSG Rod nd Configuration: Roller Type asic style: Flange mounting These 2 figures show the piston rod extended. ore size: ø, ø RSG-R K/K2 (1 + ) ø24 4 x 1. (12) 2 ø. (Rc 1/, NPT 1/, G 1/) (Rc 1/, NPT 1/, G 1/) Workpiece transfer direction RSRSH R RC C..X ø2 ø.1 TS C..S stroke.1 4 x ø through Q RHC CC uilt-in One-touch fittings øq Tubing O.D. øq QV ore size 4 Q Q QV. Note 1) In the case of single acting type, a One-touch fitting is on the rod side only. Note 2) These figures show the piston rod extended. Note ) For the auto switch mounting position and its mounting height, refer to page 2. 2

24 Series RSG Rod nd Configuration: Lever Type with Shock bsorber asic style: Flange mounting These 2 figures show the piston rod extended. ore size: ø, ø RSG-L Workpiece transfer direction 1. (Rc 1/, NPT 1/, G 1/) (Rc 1/, NPT 1/, G 1/) (12) 2 ø. + 4 x 1. R. ø.1 ø ø x ø through stroke 1 + uilt-in One-touch fittings Tubing O.D. øq øq QV 11 ore size 4 Q Q QV. Note 1) In the case of single acting type, a One-touch fitting is on the rod side only. Note 2) These figures show the piston rod extended. Note ) For the auto switch mounting position and its mounting height, refer to page 2. 24

25 Stopper Cylinder/djustable ounting Height Series RSG Rod nd Configuration: Lever Type with Shock bsorber Variable energy absorbing type/flange mounting style These 2 figures show the piston rod extended. djustable shock absorber stroke RSG- K/K2 Workpiece transfer direction djustment bolt 1. (Rc 1/, NPT 1/, G 1/) (Rc 1/, NPT 1/, G 1/) (12) 2 ø. ( + ) 4 x 1. R. ø 24 RSRSH R RC C..X.1 ø ø2 TS C..S Q 4 x ø through stroke RHC CC Tubing O.D. øq øq QV Workpiece transfer direction 11 With cancel cap RSG-C Dimensions when equipped with cancel cap are the same as the drawing above. Cancel cap Cancel cap ore size 4 Q Q QV. Note 1) In the case of single acting type, a One-touch fitting is on the rod side only. Note 2) These figures show the piston rod extended. Note ) For the auto switch mounting position and its mounting height, refer to page 2. Note 4) The figure shows these dimensions when the adjustment bolt is lowered (when energy absorption is at its maximum). However, these dimensions change within the ranges shown below as the adjusting bolt is raised (energy absorption is reduced). 24,. 11., 2

26 Series RSG Rod nd Configuration: Lever Type with Shock bsorber Variable energy absorbing type/flange mounting style These 2 figures show the piston rod extended. With lock mechanism RSG-D Workpiece transfer direction djustment bolt 1. (Rc 1/, NPT 1/, G 1/) (Rc 1/, NPT 1/, G 1/) (12) 2 ø. ( + ) 4 x 1. R. ø 24.1 ø ø2 4 x ø through stroke 1 + Workpiece transfer direction Tubing O.D. øq øq QV 11 With lock mechanism + Cancel cap RSG- Dimensions when equipped with lock and cancel cap are the same as the figure drawing. Cancel cap Cancel cap ore size 2 4 Q Q QV. Note 1) In the case of single acting type, a One-touch fitting is on the rod side only. Note 2) These figures show the piston rod extended. Note ) The figure shows these dimensions when the adjustment bolt is lowered (when energy absorption is at its maximum). However, these dimensions change within the ranges shown below as the adjusting bolt is raised (energy absorption is reduced). 24,. 11.,

27 Reed uto Switch D- Hs Hs D-C D-C D-CC D-CC Series RSG uto Switch ounting 1 uto Switch Proper ounting Position (Detection at nd) and Its ounting Height ( ): For D- type uto switch (22) 24. Solid State uto Switch D- D-W D- Hs Hs D-H D-HW D-HNF D-H D-HC uto switch 22 K/K2 RSRSH R RC C..X TS C..S Q RHC CC Hs Hs uto Switch Proper ounting Position uto switch D-C model D- Note 2) D-(V) Note 2) D-C D-W D-V D-CC D-(V) D-CC ore size D-H D-HW D-H D-HC D-HNF ore size Note 1) djust the auto switch after confirming the operating conditions in the actual setting. Note 2) uto switch mounting (The adjustment as shown in the figures below is required) uto Switch ounting Height uto switch model D-V D-WV D-V D-V Hs. 41. D- D-W D- D- D-H D-HW D-HNF D-H D-C/C Hs.. D-HC Hs. 4. D-CC D-CC Hs. 4. Different surfaces With 2 auto switches Same surface. 1 uto switch model The proper auto switch mounting position is mm inward from the switch holder edge. The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. 2

28 Operating Range Series RSG uto Switch ounting 2 uto switch model D-(V) D-(V) D-W(V) D-(V) D-C/C D-CC/CC D-H/HW D-H/HNF D-HC. Since this is a guideline including hysteresis, not meant to be guaranteed. (ssuming approximately ±% dispersion) There may be the case to change substantially depending on an ambient environment. ore size 4. uto Switch ounting racket: Part No. uto switch model D-(V) D-(V) D-W(V) D-(V) D-C/C D-CC/CC D-H D-HW D-H D-HNF ø Note 1) - Note 2) -S 2- ore size ø Note 1) - Note 2) -S 2- Note 1) Set part number which includes the auto switch mounting band (2-) and the holder kit (J-1/Switch bracket: Transparent). Since the switch bracket (made from nylon) are affected in an environment where alcohol, chloroform, methylamines, hydrochloric acid or sulfuric acid is splashed over, so it cannot be used. Please consult SC regarding other chemicals. Note 2) Set part number which includes the auto switch mounting band (2-S/Stainless steel screw) and the holder kit (J4-1/Switch bracket: White). Note ) For the D- (V) type auto switch, do not install the switch bracket on the indicator light. [ounting screw set made of stainless steel] The following set of mounting screws made of stainless steel is available. Use it in accordance with the operating environment. (Please order the auto switch mounting bracket separately, since it is not included.) D-H auto switch is set on the cylinder with the stainless steel screws above when shipped. When an auto switch is shipped independently, 4 is attached. Note 4) Refer to the uto Switch Guide for the details of 4. a Switch bracket b Switch holder c uto switch mounting band (1) J-1 is a set of a and b. J4-1 (Switch bracket: White) J-1 (Switch bracket: Transparent) (2) 2-(S) is a set of c and d. and (c) is mounted so that the projected part is on the internal side (contact side with the tube). uto switch d uto switch mounting screw esides the models listed in How to Order, the following auto switches are applicable. Refer to the uto Switch Guide for detailed specifications. uto switch type Part no. lectrical entry (Direction) Reed Solid state D-C, C D-C D-H1, H2, H D-HNW, HPW, HW D-H Grommet (In-line) Features Without indicator light Diagnostic indication (2-colour) For solid state auto switches, auto switches with a pre-wired connector are also available. Refer to the uto Switch Guide for details. Normally closed (NC = b contact) solid state auto switches (D-FG/FH types) are also available. Refer to the uto Switch Guide for details. 2

29 Series RSQ/RSG Specific Product Precautions 1 e sure to read before handling. Refer to Safety Instructions and ctuator and uto Switch Precautions. Danger Selection 1. Use within the range of specifications. If using beyond the specifications, excessive impacts or vibrations could be applied to the stopper cylinder and might cause breakage. Danger 1. Do not allow a pallet to collide with the cylinder when the lever is upright. In the case of the lever type with built-in shock absorber, if the next pallet runs into the lever when it is in the upright position (after the shock absorber has assimilated energy), the cylinder body will receive the full energy of the impact, and this should not be permitted. 2. Do not apply pressure from the head side of a single acting type cylinder. If air is supplied from the head side of a single acting cylinder, blow-by of the air will occur.. Do not scratch or gouge the sliding portion of a piston. Quenching of the piston rod has not been performed. If there is a danger of scratching or nicking the piston rod due to sharp edges, etc. on the contact area of a pallet, the pallet should not be used, as this can cause a malfunction. 4. When using a stopper cylinder for intermediate stopping of a load connected directly to a cylinder, etc. The operating ranges shown in this catalogue apply only for stopping of a pallet on a conveyor. When using a stopper cylinder to stop a load connected directly to a cylinder, etc., the cylinder thrust will become a lateral load. In this case, refer to the instruction manual and select a cylinder remaining within the allowable energy and allowable lateral load ranges.. For the lever type with a built-in shock absorber (without a lock mechanism), the lever may be pushed back in the opposite direction to the transfer direction due to the return force of the shock absorber, if N of thrust or more in the transfer direction is not applied to the lever after the pallet collides with the lever. If the lever must be continuously upright, select a lever with a lock mechanism.. The operating range for the lever type with a built-in shock absorber indicates the range in which the lever is not damaged due to the shock absorber's performance and cylinder rigidity. It is not the same as the range in which the lever can stop softly and fully. Near the upper limit, collision may occur at the end. If a soft stop is required, sufficient clearance is necessary. Consult with SC when a reliable soft stop is required near the upper limit. Caution 1. Do not apply rotational torque to the cylinder rod. In order to prevent rotational torque from acting upon the cylinder rod, mount it so that the contacting surfaces of the pallet and cylinder are parallel to one another. When mounting a cylinder, tighten the body lock nut, and then tighten the set screws (2 locations) which are included with the lock nut. (xcept RSQ) 2. When the lever type with a built-in shock absorber is installed from the direction of the lever side, mounting holes must be machined in accordance with recommend hole diameters in the table below. When it is installed from the direction of the lever side of the stopper cylinder as shown below, note that the lever's outer diameter is larger than the rod cover boss diameter. ød Figure 1 øt Caution ounting ounting base Table 1 Recommended hole diameter odel RS (D) RS (D) RS (D) Operation Lever type models RS (D) //-L RS (D) //- RS (D) //-C RS (D) //-D RS (D) //- Rod cover boss O.D. øt 44 Recommended hole diameter for mounting base ød 4 1. For models having the rod end configuration with the lever type with lock mechanism, do not apply any external force from the opposite side when the lever is locked. Doing so may cause the lock mechanism to break. When moving pallets during conveyor adjustments, first lower the cylinder. 2. Do not use oil, etc. on the sliding parts of the piston rod. This can cause trouble with retraction or other malfunctions.. Do not get your hands caught during cylinder operation. Since the lever section moves up and down when the cylinder is in operation, take sufficient care to avoid getting your hands caught between the rod cover and the lever holder. 4. Do not expose the shock absorber to machining oil, water, or dust. This will cause the shock absorber to become damaged, leading to air leaks. K/K2 RSRSH R RC C..X TS C..S Q RHC CC 2

30 Series RSQ/RSG Specific Product Precautions 2 e sure to read before handling. Refer to Safety Instructions and ctuator and uto Switch Precautions. 1. How to replace the shock absorber 1) Loosen the hexagon socket head set screw () on the piston rod. Hexagon socket head set screw Lay down. Caution 2) With the lever laid down as shown in the figure, pull out the shock absorber to remove it and replace this shock absorber with a new one. Lever Shock absorber Replacement aintenance Caution RSQ to / How to change the piston rod orientation 1) Loosen two hexagon socket head cap screws () on the rod cover that secure the non-rotating guide. 2) djust the orientation of the piston rod to a desired position. Note) Put the pallet contact surface in parallel to the cylinder contact surface so that the rotational torque does not apply to the piston rod. ) Tighten two hexagon socket head cap screws to secure the non-rotating guide. When tightening the hexagon socket head cap screws, apply the thread locking agent. Tightening torque:. N m Note) The non-rotating guide is secured by two hexagon socket head cap screws. If one hexagon socket head cap screw is tightened excessively, the non-rotating guide may be in contact with the piston rod, causing malfunction. Therefore, tighten the hexagon socket head cap screws alternately and pay special attention so that the non-rotating guide is not in contact with the piston rod. 4) ake sure that the cylinder operates smoothly. ) Insert the hexagon socket head set screw into the piston rod, and then tighten it. fter the hexagon socket head set screw has been in contact with the end, tighten it further 1/4 turn as a guideline. If the hexagon socket head set screw is tightened excessively, this may cause it to break or the shock absorber to malfunction. Tightening torque:.2 N m 2. How to change the piston rod orientation For the roller type and lever type, put the pallet in contact with the piston rod in the direction shown in the figure. (The piping port position has been made flush with the pallet contact surface at the factory shipment.) Pallet Pallet Pallet Lever type Roller type Roller type (RSQ12) RSQ12 / How to change the piston rod orientation 1) Loosen the hexagon socket head cap screws (2 locations) that secure the rod cover and cylinder tube. 2) djust the orientation of the rod cover to a desired position. The orientation of the rod cover can be changed in steps. ) Tighten two hexagon socket head cap screws on the diagonal line to secure the rod cover and cylinder tube. When tightening the hexagon socket head cap screws, apply the thread locking agent. Tightening torque: 1. N m 4) ake sure that the cylinder operates smoothly. Cylinder tube Hexagon socket head set screw Hexagon socket head set screw Non-rotating guide. How to adjust the lever type, variable energy absorbing type For the lever type, variable energy absorbing type, strokes of the shock absorber can be adjusted with an adjustment bolt included in order to stop in accordance with the transfer conditions. Follow the procedures below to adjust strokes. Procedures 1) Loosen the set screw (4) on the lever side. 2) djust the adjustment bolt in accordance to the energy of the transferred object. (The stroke of the shock absorber becomes larger (absorbing energy becomes bigger) when tightening the adjustment bolt, while it becomes smaller when loosening the bolt.) ) fter adjusting the adjustment bolt, fix the bolt with the set screw (4) loosened in 1). Tightening torque 4: 1. N m djustment bolt Lever Set screw (4) Rod cover ounting bolt for rod cover

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil With auto switch RSG RSDG With auto switch (uilt-in magnet) uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the

More information

Series RQ. The new standard for the future. Compact Cylinder with Air Cushion. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100

Series RQ. The new standard for the future. Compact Cylinder with Air Cushion. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 1 Compact Cylinder with ir Cushion ø, ø, ø, ø, ø, ø, ø, ø The new standard for the future J CQ U - NW ir Cushion Cylinder Uses a unique air cushion mechanism with no cushion ring. Size ø, ø and ø newly

More information

Magnetically Coupled Rodless Cylinder Slider Type: Ball Bushing Bearing. How to Order CY1L 25 H 300 J79W. Load voltage 5 V 200V 100 V 12 V 5 V, 12 V

Magnetically Coupled Rodless Cylinder Slider Type: Ball Bushing Bearing. How to Order CY1L 25 H 300 J79W. Load voltage 5 V 200V 100 V 12 V 5 V, 12 V Magnetically Coupled Rodless Cylinder Slider Type: all ushing earing Series CY1L ø, ø, ø, ø, ø, ø, ø How to Order CY1L H 00 J79W Slider type (all bushing bearing) mm mm mm mm mm mm mm Magnetic holding

More information

Compact Guide Cylinder

Compact Guide Cylinder Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

ISO Standard Hydraulic Cylinder

ISO Standard Hydraulic Cylinder ISO Standard ydraulic ylinder Series S/SG Series S Q N Nominal pressure: S Pa ore size :,,,, Related quipment Series SG Nominal pressure: - Pa ore size : 3,,,,, 51 ISO Standard ydraulic ylinder Series

More information

3 Position Cylinder. RZQ Series. Provides intermediate stop mechanism. ø32, ø40, ø50, ø63. 2-stage stroke enabled with a small increase in length

3 Position Cylinder. RZQ Series. Provides intermediate stop mechanism. ø32, ø40, ø50, ø63. 2-stage stroke enabled with a small increase in length Position ylinder Series ø, ø, ø, ø Provides intermediate stop mechanism 2-stage stroke enabled with a small increase in length Overall length of cylinder tube DQ2 Full stroke First-stage stroke dditional

More information

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8 Precision Cylinder Series, ø, ø6, ø, ø, ø, ø MXS Series Variations Model 8 Standard stroke (mm) 7 7 Rod end configuration Cushion Rubber bumper End lock Made to Order Rod Variable stroke/ through-hole

More information

Slide Unit. CX2/CXWM/CXWL Series. Slide Bearing/CX2:ø10, ø15, ø25 CXWM:ø10, ø16, ø20, ø25, ø32 Ball Bushing Bearing/CXWL:ø10, ø16, ø20, ø25, ø32

Slide Unit. CX2/CXWM/CXWL Series. Slide Bearing/CX2:ø10, ø15, ø25 CXWM:ø10, ø16, ø20, ø25, ø32 Ball Bushing Bearing/CXWL:ø10, ø16, ø20, ø25, ø32 Slide Unit CX/M/L Series Slide Bearing/CX:ø0, ø, ø5 M:ø0, ø, ø0, ø5, ø3 Ball Bushing Bearing/L:ø0, ø, ø0, ø5, ø3 Provided with shock absorbers to absorb impact and noise. The slide unit can absorb energy

More information

Compact Guide Cylinder Series MGQ

Compact Guide Cylinder Series MGQ Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø0 ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

Compact Slide. Series MXH ø6, ø10, ø16, ø20

Compact Slide. Series MXH ø6, ø10, ø16, ø20 Compact Slide Series ø, ø, ø, ø The use of an endless track linear guide produces a table cylinder having excellent rigidity, linearity and non-rotating accuracy. Endless track linear guide Series Variations

More information

Compact Cylinder. ISO Standard (21287) C55 Series. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. RoHS C85 C75 C96 C96Y C96K C55

Compact Cylinder. ISO Standard (21287) C55 Series. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. RoHS C85 C75 C96 C96Y C96K C55 55 96Y 96K 96 P96K P96 75R 75K-S/T 75K 75-S/T 75W 75 85R 85K-S/T 85K 85-S/T 85W 85 ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Related ade to uto Products Order Switch ompact ylinder 55 Series ISO Standard

More information

Toggle Type Air Gripper

Toggle Type Air Gripper ø2, ø40, ø50, ø6 Ideal for gripping heavy workpiece Toggle mechanism is adopted. Holds workpiece even when pressure drops. The toggle mechanism that activates when the finger closes realizes strong and

More information

Mini Free Mount Cylinder

Mini Free Mount Cylinder Mini Free Mount Cylinder Series ø, ø, ø, ø, ø, ø1, ø Series 1 ction Stroke 1 2 0 0 0 Clean uto switch series None Rod end Male threaded Without thread Solid state switch D-F D-M9 D-M9 W Female threaded

More information

Compact Cylinder: Large Bore Size Type Double Acting, Double Rod. How to Order. Cushion C Rubber bumper. Action. D Double acting

Compact Cylinder: Large Bore Size Type Double Acting, Double Rod. How to Order. Cushion C Rubber bumper. Action. D Double acting Compact Cylinder: Large Bore Size Type Double Acting, Double Rod Series CQ2W ø, ø, ø, ø, ø Without auto switch With auto switch B Built-in magnet CQ2WB CDQ2WB Double rod ounting style Through-hole/Both

More information

Platform Cylinder. ø12, ø16, ø20, ø25, ø32, ø40. Series CXT 12 CXT 16 CXT 20 CXT 25 CXT 32 CXT 40

Platform Cylinder. ø12, ø16, ø20, ø25, ø32, ø40. Series CXT 12 CXT 16 CXT 20 CXT 25 CXT 32 CXT 40 Platform Cylinder Series ø, ø, ø, ø, ø, ø highly rigid and highly accurate slide table integrated with an actuator. Two styles of guide rod bearings to accommodate your application For heavy loads all

More information

Compact Cylinder With Solenoid Valve

Compact Cylinder With Solenoid Valve Compact Cylinder With Solenoid Valve Series ø, ø, ø, ø Valve and compact cylinder integrated for compactness Solenoid valve abor saving No need to select size of valve ess piping work Compact cylinder

More information

Valve Mounted Cylinder Double Acting, Single Rod. How to Order. Electrical entry. L L plug connector M M plug connector. G Grommet

Valve Mounted Cylinder Double Acting, Single Rod. How to Order. Electrical entry. L L plug connector M M plug connector. G Grommet L F Mounting style asic style xial foot style Rod side flange style With auto switch CVJ L CDVJ L 6 6 How to Order pplicable uto Switches/Refer to pages to for further information on auto switches. Type

More information

3 Position Cylinder. ø32, ø40, ø50, ø63 RZQ CDQ2. Bore size (mm)

3 Position Cylinder. ø32, ø40, ø50, ø63 RZQ CDQ2. Bore size (mm) Position ylinder Series ø, ø, ø, ø Provides intermediate stop mechanism 2-stage stroke enabled with a small increase in length Overall length of cylinder tube First-stage stroke Full stroke dditional cylinder

More information

Slide Unit. Bore size. ø15 (2) ø10 (2) ø16 (3) ø20 (2) Ball bushing bearing Slide bearing. ø25 (3) (3) ø32 (3)

Slide Unit. Bore size. ø15 (2) ø10 (2) ø16 (3) ø20 (2) Ball bushing bearing Slide bearing. ø25 (3) (3) ø32 (3) Slide Unit Series CX/M/L Slide Bearing/CX:ø, ø, ø5 M:ø, ø6, ø0, ø5, ø3 Ball Bushing Bearing/L:ø, ø6, ø0, ø5, ø3 Provided with shock absorbers to absorb impact and noise. The slide unit can absorb energy

More information

Compact Cylinder: Standard Type Double Acting, Single Rod. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order. Piping A76H A72H 200 V

Compact Cylinder: Standard Type Double Acting, Single Rod. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order. Piping A76H A72H 200 V Compact Cylinder: Standard Type Double cting, Single Rod,,,,,,,,, How to Order Without auto switch D With auto switch CDQ2 D JW S uilt-in magnet Mounting style Through-hole (Standard) oth ends tapped style

More information

Stopper Cylinder ø16, ø20, ø32, ø40, ø50

Stopper Cylinder ø16, ø20, ø32, ø40, ø50 Stopper Cylinder ø16, ø, ø32, ø40, ø50 RoS dditional variations now include the option to have a female rod end on the round bar type and the chamfered type. 8 types 10 types The new body allows for auto

More information

How to Order. Manual release type. Lock position. H Head end lock. With rod boot. Nil J K M9NWV M9NW H7C M9PWV M9PW M9BWV M9BW M9NAV M9NA M9PAV M9PA

How to Order. Manual release type. Lock position. H Head end lock. With rod boot. Nil J K M9NWV M9NW H7C M9PWV M9PW M9BWV M9BW M9NAV M9NA M9PAV M9PA Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (0) - www.cmafh.com CDG1 With auto switch (uilt-in magnet) Mounting style asic style L xial foot style F Rod side

More information

Compact Hydraulic Cylinder

Compact Hydraulic Cylinder ompact Hydraulic ylinder Series HQ HQ Series HQ HK HN HM HS H2 H Nominal pressure:. MPa ore size :,,,,,, . MPa ompact Hydraulic ylinder Double cting/single Rod Series H Q ø, ø, ø, ø, ø, ø, ø With uto Switch

More information

Compact Cylinder. Series CQS CUJ CU CQS CQ2 RQ CQM MU

Compact Cylinder. Series CQS CUJ CU CQS CQ2 RQ CQM MU Compact Cylinder Series ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility for

More information

22mm Space required between the bottom of the cylinder body and your equipment is reduced.

22mm Space required between the bottom of the cylinder body and your equipment is reduced. Compact Guide Cylinder ø2,,, ø2,,, ø0, ø63,, ø0 With air cushion Water resistant cylinder are now available. New Up to 7% Weight reduced! New Weight reduced by up to 7% with a shorter guide rod and thinner

More information

Heavy Duty Stopper Cylinder

Heavy Duty Stopper Cylinder Heavy Duty Stopper Cylinder Series ø, ø32 To stop pallets gently Stopper cylinder with built-in shock absorber Amount of energy absorption can be adjusted to suit the load. Stops the workpiece gently with

More information

Compact Cylinder with Lock

Compact Cylinder with Lock ompact ylinder with ock Series Q ø, ø, ø, ø, ø, ø, ø, ø J2 2 1 1 N N N NS S Q RQ U P 1 rop prevention when the pressure of air source is decreased or the residual pressure is released. rop prevention for

More information

Platform Cylinder. CXT Series. ø12, ø16, ø20, ø25, ø32, ø40. A highly rigid and highly accurate slide table integrated with an actuator.

Platform Cylinder. CXT Series. ø12, ø16, ø20, ø25, ø32, ø40. A highly rigid and highly accurate slide table integrated with an actuator. Platform Cylinder Series ø, ø, ø, ø, ø, ø highly rigid and highly accurate slide table integrated with an actuator. Two types of guide rod bearings to accommodate your application For heavy loads all bushing

More information

Rotary Clamp Cylinder

Rotary Clamp Cylinder Rotary Clamp Cylinder ø, ø, ø, ø, ø, ø, ø, ø llowable moment of inertia 3 times higher New structure! New series Overall length is the same as the existing products! Mounting dimensions are interchangeable

More information

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP CT.S-7 C Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 New end lock type introduced to Series . Top mount Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Four mounting types

More information

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting.

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting. Compact Cylinder: Type Series ø, ø, ø, ø How to Order Without auto switch D With auto switch CDQS D FW S Number of auto switches L F G D, uilt-in magnet Mounting style Through-hole/oth ends tapped common

More information

Rotary Clamp Cylinder

Rotary Clamp Cylinder Rotary Clamp Cylinder ø, ø, ø, ø, ø, ø, ø, ø llowable moment of inertia 3 times higher New structure! New series Overall length is the same as the existing products! Mounting dimensions are interchangeable

More information

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations.

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Free Mount Cylinder Series CU A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Space-saving The multiple surface direct mounting with a square

More information

ISO Standard Hydraulic Cylinder

ISO Standard Hydraulic Cylinder IO tandard ydraulic ylinder eries / eries eries Nominal pressure: a ore size :,,,, Q N Related quipment - Nominal pressure: a ore size : 3,,,,, 4 IO tandard ydraulic ylinder eries Nominal pressure a/ a

More information

Guide Cylinder MGG. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. Integration of a basic cylinder and guide rods

Guide Cylinder MGG. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. Integration of a basic cylinder and guide rods Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical () 46-54 www.cmafh.com Guide Cylinder Series MGG ø, ø, ø, ø, ø, ø, ø, ø Integration of a basic cylinder and guide

More information

Compact Cylinder/Plate type

Compact Cylinder/Plate type Compact Cylinder/Plate type Series :,,, Width: Reduced by up to % (compared with SMC series) Total length: Reduced by up to % Volume: Reduced by up to 1% Weight: Reduced by up to % (compared with SMC series

More information

Series RSH/RS1H. To stop pallets gently. Heavy Duty Stopper Cylinder. Stopper cylinder with built-in shock absorber. ø20, ø32 ø50, ø63, ø80

Series RSH/RS1H. To stop pallets gently. Heavy Duty Stopper Cylinder. Stopper cylinder with built-in shock absorber. ø20, ø32 ø50, ø63, ø80 1 eavy Duty Stopper Cylinder Series RS/RS1 ø, ø ø, ø, ø To stop pallets gently CX CY RC RS A MI S C G5-S Stopper cylinder with built-in shock absorber - -9-1 2 eavy Duty Stopper Cylinder Series RS/RS1

More information

Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43

Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43 CAT.EUS- B -UK Free Mount Cylinder A space-saving air cylinder with multiple surfaces capable of direct mounting. Offered in many variations. Space-saving The multiple surface direct mounted rectangular

More information

Sine Rodless Cylinder Series RE asic Type/ø, ø, ø, ø, ø3 asic type Sine rodless cylinder (basic type) Specifications Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and

More information

Round Type Hydraulic Cylinder

Round Type Hydraulic Cylinder Round Type ydraulic Cylinder CM Series CQ CK C CM CS C C D- CM Series ominal pressure: 3. MPa ore size :,,, 3 3. MPa Round Type ydraulic Cylinder CM Series ø, ø, ø, ø pplicable uto Switches/Refer to pages

More information

ISO Standard Hydraulic Cylinder

ISO Standard Hydraulic Cylinder IO tandard ydraulic ylinder eries / eries eries Nominal pressure: a ore size :,,,, Q N Related quipment - Nominal pressure: a ore size : 3,,,,, ourtesy of teven ngineering, Inc.- Ryan Way, outh an rancisco,

More information

Compact Cylinder. With a short overall length, the space saving cylinder helps to make various jigs and equipment more compact.

Compact Cylinder. With a short overall length, the space saving cylinder helps to make various jigs and equipment more compact. Compact Cylinder Series CQ ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø1, ø With a short overall length, the space saving cylinder helps to make various jigs and equipment more compact. Variations Standard Series

More information

Compact Cylinder. With a short overall length, the space-saving cylinder helps to make various jigs and equipment more compact.

Compact Cylinder. With a short overall length, the space-saving cylinder helps to make various jigs and equipment more compact. Compact Cylinder Series CQ ø, ø, ø, ø, ø, ø, ø, ø3, ø, ø, ø, ø1, ø, ø, ø With a short overall length, the space-saving cylinder helps to make various jigs and equipment more compact. Series Variations

More information

Air Cylinder: Standard Type Double Acting, Single Rod. How to Order. Standard stroke (mm) ø6 15, 30, 45, 60. Cushion Nil A

Air Cylinder: Standard Type Double Acting, Single Rod. How to Order. Standard stroke (mm) ø6 15, 30, 45, 60. Cushion Nil A ø, ø, ø L F D Without auto switch With auto switch style asic style Axial foot style Rod side flange style Double clevis style (Except ø) ore size mm mm mm How to Order Standard stroke (mm) ø,,, ø,,,,

More information

Compact Cylinder Remodeled with a new body to get more flexibility! Can mount small auto switches on 4 surfaces.

Compact Cylinder Remodeled with a new body to get more flexibility! Can mount small auto switches on 4 surfaces. Compact Cylinder Remodeled with a new body to get more flexibility! Can mount small auto switches on 4 surfaces. New uto switches can be mounted on any of the 4 surfaces, depending on the installation

More information

Elliptical design for space-savings

Elliptical design for space-savings Plate Cylinder Series,,,, By adopting an elliptical piston design, a slim, square shaped body has been achieved, resulting in a space-saving cylinder with unrestricted mounting directions. Elliptical design

More information

/ ø6, ø10, ø16, ø20 A table cylinder suitable for short pitch mounting

/ ø6, ø10, ø16, ø20 A table cylinder suitable for short pitch mounting roduces a table cylinder non-rotating accuracy MXH / ø, ø, ø1, ø A table cylinder suitable for short pitch mounting Application example Auto switches offer numerous variations Reed switches, solid state

More information

Small Bore Hydraulic Cylinder

Small Bore Hydraulic Cylinder Small ore ydraulic Cylinder CN Series CQ CK CN CM CS C C D- CN Series Nominal pressure: MPa ore size :,,, Stainless Steel Tube Small ore ydraulic Cylinder for MPa CN Series ø, ø, ø, ø Equipped with cushion

More information

Air Cylinder: With End Lock. How to Order. Port thread type. Cylinder stroke (mm) For more information, please refer to the next page.

Air Cylinder: With End Lock. How to Order. Port thread type. Cylinder stroke (mm) For more information, please refer to the next page. ir Cylinder: With End ock Series C ø, ø, ø, ø, ø Without auto switch With auto switch F G C D T With auto switch Mounting style asic style xial foot style Rod side flange style Head side flange style Single

More information

Guide Cylinder/Compact Type

Guide Cylinder/Compact Type Guide Cylinder/Compact Type Series ø, ø, ø, ø, ø Integration of guide rods and a base cylinder ir cushion is standard. Enables the impact to be absorbed at the stroke end when the cylinder is operated

More information

Compact Guide Cylinder

Compact Guide Cylinder Compact Guide Cylinder Series ø2, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Series standard type and series high precision ball bushing bearing type (except with end lock) products have been remodeled for a lightweight

More information

How to Order. Nil M. Action S T. Load voltage Wiring. M9NV 5 V, 12 V 3-wire (PNP) M9PV 12 V. F9NWV 5 V, 12 V 3-wire (PNP) F9PWV

How to Order. Nil M. Action S T. Load voltage Wiring. M9NV 5 V, 12 V 3-wire (PNP) M9PV 12 V. F9NWV 5 V, 12 V 3-wire (PNP) F9PWV ompact ylinder: Standard Type Single cting, Single Rod, Spring Return/Extend Series QS ø, ø, ø, ø How to Order QS S QS S FWV S uilt-in magnet Mounting style Through-hole/oth ends tapped common (Standard)

More information

Air Slide Table. ø8, ø12, ø16, ø20, ø25. Linear guide table provides long stroke. Table rigidity is constant throughout entire stroke.

Air Slide Table. ø8, ø12, ø16, ø20, ø25. Linear guide table provides long stroke. Table rigidity is constant throughout entire stroke. ir Slide Table Series MX ø, ø2, ø, ø2, ø2 inear guide table provides long stroke. Table rigidity is constant throughout entire stroke. ong stroke (Max. mm) inear guide provides long stroke, and it obtains

More information

3 times the allowable moment of inertia

3 times the allowable moment of inertia otary lamp ylinder Series Double Guide Type otation mechanism uses guide rollers. otation mechanism Non-rotating accuracy: ±0.9 ±0. (lamp part) Values for ø3, ø. omparison with our series otation angle:

More information

Round Type Hydraulic Cylinder

Round Type Hydraulic Cylinder Round Type ydraulic Cylinder Series CM CQ Series CM CK C CM CS C2 C ominal pressure: 3. MPa ore size :,,, 233 3. MPa Round Type ydraulic Cylinder Series C M ø, ø, ø, ø With uto Switch ow to Order CM L

More information

Low Profile Slide Table Series MXF ø8, ø12, ø16, ø20

Low Profile Slide Table Series MXF ø8, ø12, ø16, ø20 Low Profile Slide Table Series XF ø, ø, ø1, ø Low-profile and compact type, air slide table with the construction of guide and cylinder aligned in parallel. eat appearance Protecting stopper section with

More information

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added.

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added. ir Cylinder ø1, ø16 Double foot Double-side bossed added to the mounting types. 4 types 7 types Improved amount of mounting freedom Head cover with boss is added. Head flange are Double foot Double-side

More information

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping.

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping. Dual Rod Cylinder / Series ø,,,,, Dual rod cylinder with guide function suitable for pick & place applications. Ball bushing bearings and slide bearings are standard for all series. Dimensions for ball

More information

Series MHZJ2. How to Order MHZJ2 16 D F9PV. Body option. Nil. Port. Port

Series MHZJ2. How to Order MHZJ2 16 D F9PV. Body option. Nil. Port. Port Parallel Type ir Gripper How to Order 1 1 2 Bore size mm 1mm 1mm 2mm mm MHZJ2 1 D F9PV Number of fingers 2 2 fingers D S C ction Double acting Single acting (normally open) Single acting (normally closed)

More information

Clamp Cylinder with Lock

Clamp Cylinder with Lock Clamp Cylinder with ock CK Series aintains a clamped or unclamped state when air supply pressure drops or residual pressure is released. Total length reduced by mm ody is shortened while maintaining the

More information

Brake mechanism has been compactly integrated into the slide table which enables intermediate stops of the rodless cylinder. Diaphragm.

Brake mechanism has been compactly integrated into the slide table which enables intermediate stops of the rodless cylinder. Diaphragm. rake mechanism has been compactly integrated into the slide table which enables intermediate stops of the rodless cylinder. Large holding brake force Force from 4 brake springs hold slide tightly. Holding

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR2 CRU2 CR1 MSU CRJ Rotation 360 type MSQ 360 MSZ MSQ MRQ Series Variations Page Rotating angle 80 to 0 170

More information

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover.

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover. Air Cylinder 1 Series ø32, ø40, ø50, ø63, ø80, ø100, ø125 RoHS 10 (ø50-100 stroke) % lighter Current model 1.9 kg 1 Series 1.7 kg J 1 Reduced weight by changing the shape of the rod cover and head cover.

More information

Series C95 ø32, ø40, ø50, ø63, ø80, ø100

Series C95 ø32, ø40, ø50, ø63, ø80, ø100 ISO Cylinder Series C ø, ø, ø, ø, ø, ø0 Dimensions conform to ISO 1, VDMA 2, CETOP RP3P. CJ1 CJP CJ2 CM2 C CG1 M C CA1 CS1 Variations Series Action Style asic Standard variations uit-in magnet Stainless

More information

CAT.ES20-53 E. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E Dual-Rod Cylinder Series New: Dual-Rod Cylinder with Air Cushion Compact Type Series J Dual-Rod Cylinder with guide function for pick-and-place applications Series! Twice the thrust Non-rotating

More information

Series Basic Type. ø10, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. Series MY1B

Series Basic Type. ø10, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. Series MY1B MY Series asic Type ø, ø, ø, ø, ø, ø, ø, ø, ø, ø0 Series MY earing Minimizing the unit size (dimensions) and combination with other guides is possible. efore Operating Series MY Maximum llowable Moment/Maximum

More information

Compact Guide Cylinder Series MGP

Compact Guide Cylinder Series MGP Compact Guide Cylinder Series MGP ø2, ø, ø, ø, ø, ø, ø, ø,, ø0 MGJ MGP MGQ MGG MGC MGF MGZ MGT Series Variations Series Bearing type Cushion 2 0 Page Standard type MGP With air cushion MGP With end lock

More information

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder.

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder. Compact Guide Cylinder Series ø2,,, ø2,,, ø, ø63,, ø0 Up to Weight reduced by up to 24% with a shorter guide rod and thinner plate 24% Weight reduced! 3 types of bearing can be selected. Slide bearing

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator CRQ2 Series Rack & Pinion Type/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR 2 CR1 MSU CRJ CR1 CRQ2 MSQ MSZ Rotation 360 type 360 CRQ2 MSQ MRQ Series Variations Page Rotating angle

More information

Compact Hydraulic Cylinder. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order Z73. Bore size. 20mm 25mm 32mm 40mm 50mm 63mm 80mm 100mm

Compact Hydraulic Cylinder. ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. How to Order Z73. Bore size. 20mm 25mm 32mm 40mm 50mm 63mm 80mm 100mm ompact ydraulic ylinder MPa Series KG ø, ø, ø, ø, ø, ø, ø, ø0 With uto Switch With auto switch (built-in magnet) KG DKG Mounting: asic type 0 ore size ow to Order mm mm mm mm mm mm mm 0mm Z3 Refer to "uto

More information

Series MGP. Compact Guide Cylinder. New end lock type introduced to Series MGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100

Series MGP. Compact Guide Cylinder. New end lock type introduced to Series MGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 New end lock type introduced to Series.22- CL MLG CN CNG MNB CNS CLS CB CV/MVG CXW CXS CXT MX MXU MXH MXS MXQ MXF MXW MXP MG MGQ MGG MGC MGF

More information

Direct Mount Type. REBR Series. ø15, ø25, ø32. REA REB REC Smooth MQ RHC RZQ D- -X. Low Speed

Direct Mount Type. REBR Series. ø15, ø25, ø32. REA REB REC Smooth MQ RHC RZQ D- -X. Low Speed Direct Mount Type R Series ø, ø, ø 85 R Series Selection Fn: llowable driving force (N) MD: Maximum allowable moment when connection fitting, etc., is directly loaded (N m) Pv: Maximum operating pressure

More information

Slider Type/Ball Bushing Bearing

Slider Type/Ball Bushing Bearing Slider Type/Ball Bushing Bearing Series ø, ø, ø, ø, ø, ø, ø D- -X 11 Series Selection E: Kinetic energy of load (J) V 2 E = ( 2 00 ) Es: llowable kinetic energy for intermediate stop using an air pressure

More information

Series CYP. ø15, ø32 Clean Rodless Cylinder. How to Order

Series CYP. ø15, ø32 Clean Rodless Cylinder. How to Order ø15, ø32 Clean odless Cylinder How to Order CYP 15 200 Y59 Clean rodless cylinder Cylinder bore size 15 15 mm 32 32 mm Standard stroke ore size (mm) Standard stroke (mm) 100, 150, 200, 250, 300, 350 15/32

More information

Air Slide Table. ø6, ø8, ø12, ø16, ø20, ø25. Work table and air cylinder are compactly integrated.

Air Slide Table. ø6, ø8, ø12, ø16, ø20, ø25. Work table and air cylinder are compactly integrated. ir Slide Table Series XS ø, ø, ø1, ø1, ø, ø X XU XS XQ X XW X XP XY TS Work table and air cylinder are compactly integrated. D- ndividual 9 ir slide table is suited for precision assembly. Symmetric Type

More information

Sine Cylinder. REC Series. ø20, ø25, ø32, ø40. Allows high speed transfer of work with dramatically reduced shock/impact. REA REB REC Smooth

Sine Cylinder. REC Series. ø20, ø25, ø32, ø40. Allows high speed transfer of work with dramatically reduced shock/impact. REA REB REC Smooth Sine Cylinder Series,,, llows high speed transfer of work with dramatically reduced shock/impact. RE RE RC Velocity curve Time Sine cylinder Current cylinder Sine Cylinder Series,,, llows rapid transfer

More information

Series MK ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63

Series MK ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63 otary lamp ylinder/standard Series MK ø, ø, ø, ø, ø, ø, ø5, ø ow to Order MK 1 3 S otary clamp cylinder Mounting Symbol Style ore size Through hole & both ends tapped (Standard) ø, ø oth ends tapped Through

More information

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g.

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g. Compact Slide Series ø, ø, ø, ø RoHS Allowable moment MXS Improved by up to MXQ MXQ 2% MXF MXW MXJ MXP MXY With new high rigidity linear guide MTS Allowable moment improvement illustrated below Allowable

More information

2 way basic mounting: Through-hole or both ends tapped

2 way basic mounting: Through-hole or both ends tapped Compact Cylinder Series ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility for

More information

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E -UK Dual-Rod Cylinder Series New: Dual-Rod Cylinder with Air Cushion Compact Type Series J Dual-Rod Cylinder with guide function for pick-and-place applications Series! Twice the thrust Non-rotating

More information

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping.

Dual rod cylinder with guide function suitable for pick & place applications. Adjustable stroke range: 0 to 5 mm. Axial foot piping. Dual Rod Cylinder J/ Series ø, ø, ø, ø, ø, Dual rod cylinder with guide function suitable for pick & place applications. Ball bushing bearings and slide bearings are standard for all series. Dimensions

More information

Small Bore Hydraulic Cylinder

Small Bore Hydraulic Cylinder Small ore ydraulic Cylinder CN Series CQ CK CN CM CS C C D- CN Series Nominal pressure: MPa ore size :,,, Stainless Steel Tube Small ore ydraulic Cylinder for MPa CN Series ø, ø, ø, ø Equipped with cushion

More information

Fine Lock Cylinder Double Acting, Single Rod. How to Order. Port thread type. Cylinder stroke (mm) Refer to Standard Stroke on page 718.

Fine Lock Cylinder Double Acting, Single Rod. How to Order. Port thread type. Cylinder stroke (mm) Refer to Standard Stroke on page 718. Courtesy of CM/lodyne/ydradyne Motion Control ydraulic Pneumatic lectrical Mechanical () - www.cmafh.com With auto switch With auto switch (uilt-in magnet) G C CM CM uilt-in Magnet Cylinder Model If a

More information

SeriesMHZL2 How to Order

SeriesMHZL2 How to Order Parallel Type ir Gripper Long Stroke SeriesMHZL2 How to Order 1 2 2 ore size Number of fingers 2 2 fingers 1mm mm 2mm 2mm MHZL2 D S C ction Double acting Single acting (normally open) Single acting (normally

More information

Dual Rod Cylinder: Double Rod Type. How to Order. Load voltage Auto switch model Perpendicular In-line 3-wire (NPN equivalent) Y7NWV Y7NW 5 V, 12 V

Dual Rod Cylinder: Double Rod Type. How to Order. Load voltage Auto switch model Perpendicular In-line 3-wire (NPN equivalent) Y7NWV Y7NW 5 V, 12 V Dual Rod Cylinder: Double Rod Type eries CXW ø, ø, ø, ø, ø2, ø32 CX W L How to Order 0 Y7W M L Double rod type earing type lide bearing all bushing bearing ore size/troke ore size,,,,,,,,,,,,,,, 2, 32,

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm 360 type 360 CR2 CRU2 CR1 MSU CRJ CR1 MSQ MSZ MSQ MRQ Series Variations Standard Made to Order Rotating angle

More information

Miniature Guide Rod Cylinder ±0.1. Mounting from 2 directions

Miniature Guide Rod Cylinder ±0.1. Mounting from 2 directions Miniature Guide Rod Cylinder Series Non-rotating accuracy : Height ±0.1 Mounting from 2 directions idth Overall length Two auto switches can be mounted even for mm strokes Integral wiring/piping to one

More information

Guide Table. ø40, ø63, ø100

Guide Table. ø40, ø63, ø100 Guide Table Series MGF ø, ø, ø Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Guide Table. MGF Series

Guide Table. MGF Series Guide Table MGF Series ø, ø, ø0 Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Hygienic Design Cylinder

Hygienic Design Cylinder CT.EUS- -UK Hygienic Design Cylinder New Round type Series HY has been added. water resistant cylinder configured for easy cleaning ISO standard type Series HYC asic type Series HYQ With guide Series HYG

More information

Series MGC ø20, ø25, ø32, ø40, ø50

Series MGC ø20, ø25, ø32, ø40, ø50 Compact Guide Cylinder Series MGC ø, ø, ø, ø, ø Linear Transfer Unit with compact guide body and front plate Grease nipple offers easy lubrication for bearings Compact front plate and guide body Space

More information

Mechanically Jointed Rodless Cylinder High Precision Guide Type. How to Order 16 G 300 L M9N. Stroke. Refer to Standard Stroke table.

Mechanically Jointed Rodless Cylinder High Precision Guide Type. How to Order 16 G 300 L M9N. Stroke. Refer to Standard Stroke table. Mechanically Jointed Rodless ylinder igh Precision uide Type eries MY/T ø, ø, ø T MY uide type igh precision guide with single axis igh precision guide with double axis ymbol Nil TN TF Type M thread Rc

More information

New cylinder body allows small auto switches to be mounted on 4 surfaces.

New cylinder body allows small auto switches to be mounted on 4 surfaces. Toggle Type Air Gripper ø32, ø4, ø5, ø63 New cylinder body allows small auto switches to be mounted on 4 surfaces. RoH Auto switch mounting rail removed. A round slot for mounting small auto switches is

More information

Air Slide Table. ø8, ø12, ø16, ø20, ø25. Linear guide table provides long stroke. Table rigidity is constant throughout entire stroke.

Air Slide Table. ø8, ø12, ø16, ø20, ø25. Linear guide table provides long stroke. Table rigidity is constant throughout entire stroke. ir Slide Table Series MX ø, ø2, ø, ø2, ø2 inear guide table provides long stroke. Table rigidity is constant throughout entire stroke. ong stroke (Max. mm) inear guide provides long stroke, and it obtains

More information

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types ir Cylinder Ø 6, Ø 1, Ø New RoS Double foot ead flange Double-side bossed added to the mounting types. 4 types 7 types New or Ø 6, 3 types are 6 types Double foot Double-side bossed ead flange ead cover

More information

Air Cylinder. New RoHS. Series CG1. Female rod end available as standard. Rod end styles suitable for the application can be selected.

Air Cylinder. New RoHS. Series CG1. Female rod end available as standard. Rod end styles suitable for the application can be selected. ir Cylinder ø 20, ø 25, ø 32, ø 40, ø 50, ø 63, ø 80, ø 100 New RoS Female rod end available as standard Selectable Rod end styles suitable for the application can be selected. Female thread Male thread

More information

Series MGPS. Compact Guide Cylinder: ø50, ø80 MGP S Z73. How to Order. Applicable auto switches. Compact Guide Cylinder.

Series MGPS. Compact Guide Cylinder: ø50, ø80 MGP S Z73. How to Order. Applicable auto switches. Compact Guide Cylinder. Compact Guide Cylinder: Series S ø, Compact Guide Cylinder Compact guide cylinder Heavy duty guide rod type S Z73 mm mm How to Order Number of auto switches Nil S 2 pcs. 1 pc. Auto switch type Nil Without

More information

Air Slide Table Series MXP

Air Slide Table Series MXP ir Slide Table Series XP ø, ø, ø, ø, ø1 X XU XS X XF X X XP XY TS - -X Individual -X 19 igh rigidity, igh precision Cylinder is built into the rail of the linear guide. aterial of body and guide block

More information

2 way basic mounting: Through-hole or both ends tapped

2 way basic mounting: Through-hole or both ends tapped Compact Cylinder Series CQS ø, ø, ø, ø Ideal for machine designs with small space requirements The D-M auto switch will not protrude from switch mounting groove. Square body shape gives you flexibility

More information

10 % lighter kg. Air Cylinder kg. New. New. Series. Added ø 125 to standard type.

10 % lighter kg. Air Cylinder kg. New. New. Series. Added ø 125 to standard type. ir Cylinder New ø 3, ø 40, ø 50, ø 63, ø 80, ø 100, ø 15 10 % lighter RoS (ø 40-100 stroke) Weight Existing model New 1.01 kg Series dded ø 15 to standard type. 0.91 kg Reduced weight by changing the shape

More information