22mm 17% Compact Guide Cylinder (Basic type) New ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. Up to. Series MGP. Weight reduced!

Transcription

1 Copact Guide Cylinder (Basic type) New ø, ø, ø, ø2, ø, ø, ø, ø,, ø Up to 7% Weight reduced! Weight reduced by up to 7% with a shorter guide rod and thinner plate Guide rod shortened for -2 stroke Max. 22 Space required between the botto of the cylinder body and your equipent is reduced. Space saving Round type and agnetic field resistant auto switches can be ounted directly without spacer. 3 types of bearing can be selected. Series Ball bushing Series MGP High precision ball bushing Series MGP Made to Order Change of guide rod end shape (-X), interediate stroke (-XB), low speed cylinder (-XB3), and side porting type (-X7), etc. are set additionally. Series MGP CT.NS-29B

2 Copact Guide Cylinder (Basic type) Series Suitable for lateral load applications such as a stopper where shock is applied 3 types of bearing can be selected. Ball bushing Series MGP Sooth operation suitable for pusher and lifter High precision ball bushing Series MGP Suitable for iniizing plate displaceent Ball bushing High precision ball bushing oad fro lateral direction Displaceent Weight reduced Reduction rate (%) Weight (kg) ø ø ø ø2 ø ø ø ø ø * Copared with slide bearing type, ø to ø2- stroke * Copared with slide bearing type, ø to ø-2 stroke * The D-Y7 and D-Z7 auto switches are not ountable Sall auto switches or agnetic field resistant auto switches can be ounted on 2 surfaces. D-M9 D-9 D-P3DW Guide rod shortened Projection shortened 4 types of ounting are possible.. Top ounting ø ø ø ø Guide rod Shortened by New diension ø.. * Copared with slide bearing type, 2 stroke (ø to ø) (No projection for ø to ø2-2 stroke) Perforance, strength (rigidity), and ounting diensions are equivalent to the conventional MGP series. asy positioning Knock pin holes provided on each ounting surface 2. Side ounting 4. Botto ounting T-slot side ounting asy adjustent of workpiece and cylinder ounting D-P3DW Piping is possible fro 2 directions.. Top ported 2. Side ported Features D-M9

3 Copact Guide Cylinders, Series Variations Series MGP Series Bearing type Page 2 Basic type/mgp New Reodeled Page 4 of this catalog With air cushion/mgp- With end lock/mgp-h/r Ball bushing High precision ball bushing Best Pneuatics Best Pneuatics OCK Clean series//3-mgp Ball bushing Best Pneuatics Water-resistant/MGP R/V Best Pneuatics Heavy duty guide rod/mgps Best Pneuatics Miniature Guide Rod Cylinder/MGJ Best Pneuatics Copact Guide Cylinder with ock/mgp Best Pneuatics OCK Ball bushing Hygienic Design Cylinder/HYG Best Pneuatics New Series MGP (Basic type), Stroke Variations Bearing type MGP Ball bushing MGP High precision ball bushing 2 Stroke Made to Order -X: Change of guide rod end shape -XB: Heat resistant cylinder ( to C) -XB: Interediate stroke (Using exclusive body) -XB3: ow speed cylinder ( to /s) -XC: Made of stainless steel -XC22: Fluororubber seals -XC79: Machining tapped hole, drilled hole and pin hole additionally -XC2: Botto ounting type -X44: Syetrical port position -X7: Side porting type (Plug location changed) Refer to page for details. Features 2

4 Cobination of Standard Products and Made to Order Specifications Series MGP : Standard : Made to Order : Special product (Please contact SMC for details.) : Not available Type Bearing type Model Basic type Ball bushing High precision ball bushing MGP MGP Sybol Specifications pplicable bore size ø to ø - Copper and fluorine-free Note ) Note 3) Note 3) -X Change of guide rod end shape -XB Heat resistant cylinder Note 2) (4 to 32 F (- to C)) -XB Interediate stroke (Using exclusive body) -XB3 ow speed cylinder ( to /s) -XC Made of stainless steel ø to ø -XC22 Fluororubber seals Note 2) -XC79 Machining tapped hole, drilled hole and pin hole additionally -XC2 Botto ounting type -X44 Syetrical port position -X7 Side porting type (Plug location changed) Note ) Refer to SMC website for details. Note 2) Without cushion Note 3) Copper and fluorine-free are available as standard products.

5 Series MGP Specific Product Precautions Be sure to read before handling. Refer to back cover for Safety Instructions, Handling Precautions for SMC Products (M-3-3) and the Operation Manual for ctuator Precautions and uto Switch Precautions. Please download it via our website, Warning Mounting. Never place your hands or fingers between the plate and the body. Be very careful to prevent your hands or fingers fro getting caught in the gap between the cylinder body and the plate when air is applied. Caution Mounting. Botto of cylinder The guide rods protrude fro the botto of the cylinder at the end of the retracting stroke, and therefore, in cases where the cylinder is to be botto ounted, it is necessary to provide bypass ports in the ounting surface for the guide rods, as well as holes for the hexagon socket head cap screws which are used for ounting. Moreover, in applications where ipact occurs fro a stopper etc., the ounting screws should be inserted to a depth of 2d or ore. Caution. Use cylinders within the piston speed range. n orifice is set for this cylinder, but the piston speed ay exceed the operating range if the speed controller is not used. If the cylinder is used outside the operating speed range, it ay cause daage to the cylinder and shorten the service life. djust the speed by installing the speed controller and use the cylinder within the liited range. 2. Pay attention to the operating speed when the product is ounted vertically. When using the product in the vertical direction, if the load factor is large, the operating speed can be faster than the control speed of the speed controller (i.e. quick extension). In such cases, it is recoended to use a dual speed controller. 3. Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Daaged seals etc. will result in leakage or alfunction. 4. Do not dent or scratch the ounting surface of the body and the plate. The flatness of the ounting surface ay not be aintained, which would cause an increase in sliding resistance.. Make sure that the cylinder ounting surface has a flatness of. or less. If the flatness of the workpieces and brackets ounted on the plate is not appropriate, sliding resistance ay increase. If it is difficult to aintain a flatness of. or less, put a thin shi ring (prepared by the custoer) between the plate and workpiece ounting surface to prevent the sliding resistance fro increasing. Shi ring (prepared by custoer) Workpiece Plate B C±.2 ±.2 C d or ore (d = Screw O.D.) ød Bypass port dia. B±.2 D MGP/ Hexagon socket head cap screw M4 x.7 M x. M x. M x. M x.2 M x.2 M x. M x. M x.7 M4 x 2. 2

6 Series MGP Specific Product Precautions 2 Be sure to read before handling. Refer to back cover for Safety Instructions, Handling Precautions for SMC Products (M-3-3) and the Operation Manual for ctuator Precautions and uto Switch Precautions. Please download it via our website, Caution Piping Depending on the operating conditions, piping port positions can be changed by using a plug.. M fter tightening by hand, tighten additional / to /4 rotation with a tightening tool. 2. Tapered thread for Rc port (MGP) and NPT port (MGPTN) Use the correct tightening torques listed below. Before tightening the plug, wrap pipe tape around it. lso, with regard to the sunk diension of a plug (diension a in the drawing), use the stipulated figures as a guide and confir the air leakage before operation. If tightening plugs on the top ounting port with ore than the proper tightening torque, plugs will be screwed uch deeply and air passage will be squeezed. Consequently, the cylinder speed will be restricted. Caution oad ass and a axiu speed ust be within the ranges shown in the graph below. MGP with rubber buper ø ø ø ø ø llowable Kinetic nergy Connection thread (plug) size / /4 3/ Plug Proper tightening torque (N ) 7 to 9 to 4 22 to a a diension. or less or less or less oad ass (kg) ø2 ø ø ø 3. Parallel pipe thread for G port (MGPTF) Screw in the plug to the surface of the body (diension a in the drawing) by checking visually instead of using the tightening torque shown in the table... Maxiu speed (/s) 3

7 Copact Guide Cylinder Series MGP ø, ø, ø, ø2, ø, ø, ø, ø,, ø How to Order Copact Guide Cylinder MGP M 2 Copact Guide Cylinder M Bearing type Ball bushing High precision ball bushing 2 2 Port thread type Nil TN TF M x. Rc NPT G For bore size ø and ø, only M x. is available. 3 Z M9BW Cylinder stroke Refer to Standard Strokes on page. Nuber of auto switches Nil S n uto switch Without auto switch Nil (Built-in agnet) For applicable auto switch odel, refer to the table below. Made to Order For details, refer to page. 2 pcs. pc. n pcs. pplicable uto Switches/Refer to pages 79 to 27 in Best Pneuatics No. 3 for further inforation on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color display) Water-resistant (2-color display) Magnetic field resistant (2-color display) lectrical entry Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) Groet Yes 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 2-wire (Non-polar) 3-wire Yes (NPN equivalent) Groet 2-wire No Water-resistant type auto switch can be ounted to the odels with the above entioned part nubers, but this does not guarantee the water resistance of the cylinder. water-resistant type cylinder is recoended for use in an environent which requires water resistance. However, please contact SMC for water-resistant products of ø and ø. ead wire length sybols:. Nil (xaple) M9NW M (xaple) M9NWM 3 (xaple) M9NW Z (xaple) M9NWZ Indicator light M9NV M9PV M9BV M9NWV M9PWV M9BWV M9NV M9PV M9BV 9V 93V 9V Since there are other applicable auto switches than listed, refer to page 23 for details. For details about auto switches with pre-wired connector, refer to pages 74 and 7 in Best Pneuatics No. 3. For D-P3DW, refer to the catalog CT. S-. uto switches are shipped together, (but not assebled). V V oad voltage DC V, V V V, V V V, V V V V C V V or less uto switch odel Perpendicular In-line M9N M9P M9B M9NW M9PW M9BW M9N M9P M9B P3DW ead wire length (). 3 (Nil) (M) () (Z) Pre-wired connector Solid state auto switches arked with are produced upon receipt of order. s ø to ø are available for the D-P3DW. pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC 4

8 Copact Guide Cylinder Series MGP Specifications Made to Order Sybol -X -XB -XB -XB3 -XC -XC22 -XC79 -XC2 -X44 -X7 Made to Order (For details, refer to pages 2 to 3.) Change of guide rod end shape Heat resistant cylinder (4 to 32 F ( to C)) Interediate stroke (Using exclusive body) ow speed cylinder ( to /s) Made of stainless steel Fluororubber seals Machining tapped hole, drilled hole and pin hole additionally Botto ounting type Syetrical port position Specifications Side porting type (Plug location changed) Refer to pages 22 to for cylinders with auto switches. uto switch proper ounting position (detection at stroke end) and ounting height Miniu stroke for auto switch ounting Operating range uto switch ounting brackets/part no. ction Fluid Proof pressure Maxiu operating pressure Miniu operating pressure bient and fluid teperature Piston speed Note) Cushion ubrication Stroke length tolerance,, 2 to ø ø ø ø2 ø ø ø ø ø Double acting ir 2 psi (. MPa) 4 psi (. MPa) 7.4 psi (. MPa) 4.4 psi (. MPa) 4 to F ( to C) (No freezing) to /s to /s Rubber buper on both ends Not required (Non-lube) Note) Maxiu speed with no load. Make a odel selection, considering a load according to the graph on pages 9 to. Standard Strokes 2 Rod size Standard stroke,, 3,,, 7,,,, 7,, 2, 3,,, 7,,,, 7,, 2, 3, 3, 2,, 7,,,, 7,, 2, 3, 3, Manufacture of Interediate Strokes Description Model no. pplicable stroke xaple Theoretical Output Spacer installation type Spacers are installed in the standard stroke cylinder. ø to ø: vailable by the stroke interval. ø to ø: vailable by the stroke interval. Refer to How to Order for the standard odel nubers. ø, ø to 9 Operating Piston area direction ( 2 ) OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN ø, ø2, ø ø to ø to 39 Part no.: -39Z spacer in width is installed in the -. C diension is to 399 Note) Theoretical output (N) = Pressure (MPa) x Piston area ( 2 ) +. xclusive body (-XB) Dealing with the stroke by aking an exclusive body. ll bore sizes are available by the interval. Suffix -XB to the end of standard odel nuber. For details, refer to Made to Order. ø, ø to 9 ø, ø2 OUT 2 to 399 ø to ø 2 to 399 Part no.: -39Z-XB Special body anufactured for 39 stroke. C diension is 7. ( MPa = 4 psi ) ( N =.22 lb) (N) Operating pressure (MPa) IN

9 Torque: T (N ) Stroke MGP/ MGP/ MGP/ MGP/ MGP/ MGP/ MGP/ MGP/ MGP/ MGP/ Bearing type T (N ) Weight llowable Rotational Torque of Plate Slide Bearing: to Standard stroke 2 (kg) Ball Bushing: MGP to, High Precision Ball Bushing: MGP to (kg) Standard stroke ( N =.74 lbf ft) Series MGP

10 Copact Guide Cylinder Series MGP Non-rotating ccuracy of Plate 2 ±.7 ±. ±. ±.4 ±.3 +θ θ Non-rotating accuracy θ when retracted and when no load is applied should be not ore than the values shown in the table. Non-rotating accuracy θ MGP ±. ±.4 ±.3 ±.3 ±.3 MGP ±. High Precision Ball Bushing/MGP Caution Positioning accuracy for pin hole on the plate Dispersion of diensions when achining each coponent will be accuulated in the plate pin hole positioning accuracy when ounting this cylinder. Values below are referred as a guide. [Side ounting] Pin hole [Botto ounting] Pin hole = Catalog diension ± (. + x.) [] : To be. for, ø Note) Displaceent by load and self-weight deflection by plate and guide rod are not included. B 2 Pin hole B = ± ( x.) [] 7

11 Series MGP High Precision Ball Bushing/MGP Plate Displaceent ount (Reference Values) oad fro lateral direction Displaceent MGP.4 Plate displaceent aount Plate displaceent aount MGP- 2 oad fro lateral direction (N) MGP.4 Plate displaceent aount MGP MGP- MGP- MGP-7 3 oad fro lateral direction (N) MGP-2 MGP- MGP- MGP-7 MGP-2 MGP- MGP-3 MGP- MGP- MGP- MGP- MGP- MGP- MGP- oad fro lateral direction (N) MGP/. Plate displaceent aount Plate displaceent aount oad fro lateral direction (N) MGP/ Plate displaceent aount MGP.4 oad fro lateral direction (N) MGP - MGP -3 MGP - MGP - MGP - MGP - MGP - MGP -3 MGP - MGP- MGP-3 MGP-2 MGP - MGP - MGP- MGP- MGP - MGP- MGP- oad fro lateral direction (N) MGP2 Plate displaceent aount MGP2- MGP2-3 MGP2-.2 MGP2-. MGP2- MGP2- oad fro lateral direction (N) MGP. Note ) The guide rod and self-weight for the plate are not included in the above displaceent values. Note 2) llowable rotating torque, and operating range when used as a lifter, are the sae as MGP series. Plate displaceent aount MGP- MGP-3 MGP-2 MGP- MGP- MGP- MGP- 3 oad fro lateral direction (N) ( N =.22 lbf)

12 Selection Conditions Series MGP Model Selection Vertical Horizontal Mounting orientation Maxiu speed (/s) Graph ( type) Graph (Ball bushing type) or less (), (2) () to () (3), (4) (9) to () or less (3), (4) (7), () (), () (9), () Selection xaple (Vertical Mounting) Selection conditions Mounting: Vertical Bearing type: Ball bushing Stroke: 3 stroke Maxiu speed: /s oad ass: 3 kg ccentric distance: 9 Find the point of intersection for the load ass of 3 kg and the eccentric distance of 9 on graph (), based on vertical ounting, ball bushing, 3 stroke, and the speed of /s. MGP2-3Z is selected. () 3 stroke or less, V = /s or less ø2 ø ø ø Selection xaple 2 (Horizontal Mounting) Selection conditions Mounting: Horizontal Bearing type: Distance between plate and load center of gravity: Maxiu speed: /s oad ass: 2 kg Stroke: 3 stroke Find the point of intersection for the load ass of 2 kg and 3 stroke on graph (3), based on horizontal ounting, slide bearing, the distance of between the plate and load center of gravity, and the speed of /s. -3Z is selected. (3) =, V = /s or less ø ø, ø, ø2 ø ø ø ø, ø, ø ø2 ø ø ø. ccentric distance. 3 3 Stroke When the axiu speed exceeds /s, the allowable load ass is deterined by ultiplying the value shown in the graph at /s by the coefficient listed in the table below. ( Kg = 2.2 lbs) Max. speed Coefficient Up to 3 /s.7 Up to /s Up to /s. Use the Guide Cylinder Selection Software, when the eccentric distance is or ore. 9

13 Series MGP Vertical Mounting to Slide Bearing Operating pressure psi (.4 MPa) Operating pressure 73 psi (. MPa) or ore () stroke or less, V = /s or less (2) Over stroke, V = /s or less 3 3 ø ø ø ø ø ø ø ø ø ø ø2 ø ø ø2 ø ø ø ø. ccentric distance. ccentric distance (3) stroke or less, V = /s (4) Over stroke, V = /s ø ø ø ø ø ø ø ø ø2 ø ø ø ø2 ø ø ø ø ø. ccentric distance. ccentric distance Use the Guide Cylinder Selection Software, when the eccentric distance is or ore. ( Kg = 2.2 lbs)

14 Model Selection Series MGP Vertical Mounting Ball Bushing Operating pressure psi (.4 MPa) Operating pressure 73 psi (. MPa) or ore MGP to 2, MGP to 2 () 3 stroke or less, V = /s or less () Over 3 stroke, V = /s or less ø2 ø ø2 ø ø ø ø ø. ccentric distance. ccentric distance MGP to, MGP to (7) stroke or less, V = /s or less () Over stroke, V = /s or less 3 3 ø ø ø ø ø ø ø ø ø ø ccentric distance ccentric distance Use the Guide Cylinder Selection Software, when the eccentric distance is or ore. ( Kg = 2.2 lbs)

15 Series MGP Vertical Mounting Ball Bushing Operating pressure psi (.4 MPa) MGP to 2, MGP to 2 (9) 3 stroke or less, V = /s () Over 3 stroke, V = /s. ø2 ø2 ø ø ø. ø ø ø. ccentric distance. ccentric distance MGP to, MGP to () stroke or less, V = /s () Over stroke, V = /s ø ø ø ø ø ø ø ø ø ø ccentric distance.2 ccentric distance Use the Guide Cylinder Selection Software, when the eccentric distance is or ore. ( Kg = 2.2 lbs)

16 Model Selection Series MGP Horizontal Mounting Slide Bearing to (3) =, V = /s or less (4) =, V = /s or less ø ø ø ø ø, ø, ø, ø, ø, ø, ø, ø, ø2 ø2 ø2 ø ø ø ø ø ø ø2 ø ø ø ø ø ø. 3 3 Stroke. 3 3 Stroke () =, V = /s () =, V = /s ø ø ø ø ø ø ø ø, ø ø ø ø ø, ø ø ø2 ø ø ø ø2 ø ø ø ø2 ø ø ø ø2 ø ø ø ø ø ø Stroke Stroke ( Kg = 2.2 lbs) 3

17 Series MGP Horizontal Mounting Ball Bushing (7) =, V = /s or less () =, V = /s or less MGP to 2, MGP to 2 MGP to 2, MGP to 2 ø2 ø2 ø ø2 ø ø ø ø ø ø2 ø ø2 ø ø ø ø2 ø ø ø ø ø ø ø ø Stroke Stroke MGP to, MGP to MGP to, MGP to ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, ø, 3 3 MGP/, MGP/ Stroke MGP/, MGP/ 3 3 Stroke ø ø ø ø ø ø Stroke Stroke 4 ( Kg = 2.2 lbs)

18 Model Selection Series MGP Horizontal Mounting Ball Bushing (9) =, V = /s () =, V = /s MGP to 2, MGP to 2 MGP to 2, MGP to 2 ø2 ø2 ø2 ø2 ø2 ø2 ø ø ø ø ø ø ø ø ø ø ø ø. ø ø MGP to, MGP to Stroke ø MGP to, MGP to ø ø Stroke ø ø, ø ø, ø ø ø ø ø, ø ø, ø ø ø ø ø ø ø ø ø ø MGP/, MGP/ Stroke MGP/, MGP/ Stroke ø ø ø ø ø ø Stroke Stroke ( Kg = 2.2 lbs)

19 Series MGP Operating Range when Used as Stopper Bore Size: ø to ø2/ to 2 () ( Kg = 2.2 lbs) to 2 () υ υ ø2 ø When selecting a odel with a longer diension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Mass of transferred object: (kg) ø ø Note ) When using as a stopper, select a odel with 3 stroke or less. Note 2) The MGP (Ball bushing) and the MGP (High precision ball bushing) cannot be used as a stopper. Transfer speed: υ (/in) 3 Bore Size: ø to ø/ to () to () υ υ ø When selecting a odel with a longer diension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Note ) When using as a stopper, select a odel with stroke or less. Note 2) The MGP (Ball bushing) and the MGP (High precision ball bushing) cannot be used as a stopper. Mass of transferred object: (kg) 3 3 ø ø ø ø 3 Transfer speed: υ (/in) Refer to graphs (3) and () if line pressure is applied by a roller conveyor after the workpiece is stopped.

20 Construction/Series to 2 to Copact Guide Cylinder Series MGP u! e i y! t!3!9 e i u! y ø or ore ø to ø2 stroke or less ø to ø2 Over stroke ø or ore Coponent Parts No. Description Material Note Body Piston Piston rod Collar Head cover Guide rod Plate Plate ounting bolt Guide bolt Retaining ring Retaining ring Buper Buper B Magnet Plug Hexagon socket head plug luinu alloy luinu alloy Stainless steel Carbon steel luinu alloy luinu alloy Carbon steel Carbon steel Carbon steel Carbon steel Carbon tool steel Carbon tool steel Urethane Urethane Carbon steel Bearing alloy Hard anodized Chroated ø to ø2 ø to ø Hard chroe plated Chroated ø to ø Chroated, ø Painted Hard chroe plated Nickel plated Nickel plated Nickel plated Phosphate coated Phosphate coated ø, ø ø to ø Nickel plated Coponent Parts No. Description Material Note Ball bushing Spacer Steel ball Plug Piston seal Rod seal Gasket Gasket B luinu alloy Carbon steel Carbon steel NBR NBR NBR NBR Replaceent Parts/Seal Kit 2 Kit no. MGP-Z-PS MGP-Z-PS MGP-Z-PS MGP2-Z-PS MGP-Z-PS Contents Set of ø to ø ø to ø Kit no. MGP-Z-PS MGP-Z-PS MGP-Z-PS MGP-Z-PS MGP-Z-PS Nickel plated Seal kit Order the seal kit, based on each bore size. Since the seal kit does not include a grease pack, order it separately. Grease pack part nuber: GR-S- ( g) Contents Set of 7

21 Series MGP Construction/Series MGP, Series MGP MGP to 2 MGP to 2 MGP to MGP to!!7!!7! ø to ø2 Over stroke ø or ore! ø to ø Over stroke, ø Over stroke

22 øxh7 Copact Guide Cylinder Series MGP ø to ø2/, MGP, MGP Z W WB øx H7 depth Section XX details T-slot diensions b a X (Mounting hole position) Section XX 4 x YY depth Y X±.2 (Pin hole position) XB X 3 2 a c d e b c d e T R 4 x NN through Section XX X±.2 ød Z W 4 x øo through 4 x øob counterbore depth O PW X U (O) X±.2 4 x MM depth M Section XX VB V H ødb H: T-slot for hexagon bolt øx H7 depth Q S P + Stroke F G GB FB C + Stroke B + Stroke + Stroke 2 x P 2 x P (Plug) 3 PB J K G ø, ø T-slot øx H7 depth The use of a slot (width X, length XB, depth 3) allows for a relaxed pin pitch tolerance, with the pin hole (øxh7, depth ) as the reference, without affecting ounting accuracy. For interediate strokes other than standard strokes, refer to Manufacture of Interediate Strokes on page. For bore size ø and ø, only M x. port is available. For bore size ø or ore, choice of Rc, NPT, G port is available. (Refer to page 4.), MGP, MGP Coon Diensions 2 Standard stroke,, 3,,, 7,,, 7,, 2, 3,,, 7,,, 7,, 2, 3, 3, B C D F FB 7 G G... GB H H M4 M4 M M J 3 2 K MM M4 x.7 M x. M x. M x. M 3 NN M4 x.7 M x. M x. M x. O OB O Nil TN TF M x. M x. Rc/ Rc/ P NPT/ NPT/ G/ G/ 2 P PB PW Q 4 2 R S T 2 9 U V 72 2 VB st or less Over 3 st st or less W Over st st or less Over st 3 st or less Over 3 st st or less WB Over 3 st Over st Over st st or less st or less st or less 7 7 Over 3 st 7 7 X X XB YY M x. M x. M x. M x. Y Z 7 7 (), DB, Diensions 2 st or less Over st Over st st or less st or less Over st DB st or less Over st Over st st or less st or less Over st MGP (Ball bushing) MGP (High precision ball bushing), DB, Diensions 2 3 st or less Over 3 st Over st st or less st or less Over st DB 3 3 st or less 3 Over 3 st st or less Over st st or less Over st

23 Series MGP ø to ø/, MGP, MGP øx H7 depth X Z W WB Section XX details T-slot diensions 4 x NN through Section XX X (Mounting hole position) Section XX 4 x YY depth Y X±.2 (Pin hole position) Z W 4 x øo through 4 x øob counterbore depth O 4 x MM depth M Section XX (O) ødb T R X±.2 ød PW X U X±.2 H: T-slot for hexagon bolt VB V H b a X XB øxh7 XC X a... c e d b c d e Q S øx H7 depth X F G GB FB C + Stroke B + Stroke + Stroke 2 x P PB 2 x P P + Stroke J (Plug) G K T-slot øx H7 depth X The use of a slot (width X, length XB, depth XC) allows for a relaxed pin pitch tolerance, with the pin hole (øxh7, depth X) as the reference, without affecting ounting accuracy. For interediate strokes other than standard strokes, refer to Manufacture of Interediate Strokes on page. Choice of Rc, NPT, G port is available. (Refer to page 4.), MGP, MGP Coon Diensions Standard stroke 2,, 7,, 7,, 2 3, 3, B C D 4 4 F FB G G GB H 4 2 H M M M M J K MM M x.2 M x.2 M x. M x. M NN M x.2 M x.2 M x. M x. O OB 4 O Nil TN TF Rc/ Rc/ Rc/4 Rc/4 P NPT/ NPT/ NPT/4 NPT/4 G/ G/ G/4 G/4 P PB 2. 2 PW Q 3 3 R S T 4 U 7 4 V VB st Over 2 st st or less or less W Over st st or less Over st Over 2 st Over 2 st 3 st or less 3 st or less st or less WB Over st st or less 3 4 Over st 3 st or less Over 3 st X 42 X 4 4 XB XC X YY M x.2 M x.2 M x. M x. Y Z 2 22 (), DB, Diensions st or less Over st st or less Over st DB 2 2 st or less. 9.. Over st st or less Over st MGP (Ball bushing) MGP (High precision ball bushing), DB, Diensions st or less Over st Over st st or less st or less Over st DB st or less Over st Over st st or less st or less Over st

24 Copact Guide Cylinder Series MGP, ø/, MGP, MGP ø H7 depth Z W WB Section XX details T-slot diensions X (Mounting hole position) X±.2 (Pin hole position) 7 øh7 Section XX 4 x YY depth Y 4 x NN through Section XX Z W 4 x øo through 4 x øob counterbore depth O 4 x MM depth M Section XX (O) ødb T R X±.2 ød PW X U X±.2 H: T-slot for hexagon bolt VB V H b a a c e d b c d e ø H7 depth Q S F GC G GB FB C + Stroke B + Stroke + Stroke 2 x P P + Stroke 2 x P (Plug) JB PB JC J J G The use of a slot (width X, length 7, depth ) allows for a relaxed pin pitch tolerance, with the pin hole (øh7, depth ) as the reference, without affecting ounting accuracy. For interediate strokes other than standard strokes, refer to Manufacture of Interediate Strokes on page. Choice of Rc, NPT, G port is available. (Refer to page 4.) K T-slot ø H7 depth, MGP, MGP Coon Diensions P Standard stroke 2,, 7,,, 7, 2, 3, 3, PB 2.. PW 74 9 Q 2 4 B 9. R 74 2 C. S 7 9 D 22 2 T 9 23 F 9 U FB 3 V 2 G 9.. VB G st or less 2 4 GB.. GC 4. Over 2 st st or less 2 72 H 2 2 H M M4 W Over st st or less 4 J J 3 4 Over st 3 st or less JB 7.. Over 3 st 3 3 JC K MM M x.7 M4 x M 2 3 NN M x.7 M4 x 2. P O OB O Nil TN TF.. Over 3 st X 4 3 Rc3/ NPT3/ Rc3/ NPT3/ YY M x.7 M4 x 2. MGP (Ball bushing) (), DB, Diensions MGP (High precision ball bushing), DB, Diensions st or less 4.. Over st st or less 3.. Over st. 9. DB 3 3 st or less. Over st st or less 3 3. Over st st or less 2 st or less Over 2 st st or less Over 2 st st or less. 4. WB Over st st or less Over st st or less. 7. Over st 3 st or less Over st 9.. DB st or less 3. Over 2 st st or less 29. Over st st or less 2 2. Y 2 G3/ G3/ Z 2 Over st 9. 2

25 Series MGP uto Switch Mounting uto Switch Proper Mounting Position (Detection at Stroke nd) and Its Mounting Height D-9 D-9V D-M9 D-M9V D-M9W D-M9WV D-M9 D-M9V ø to ø uto switch B D-P3DW ø to ø, ø B Ht Hs Hs uto Switch Proper Mounting Position pplicable Cylinder Series: MGP 2 uto switch odel D-M9 D-M9V D-M9W D-M9WV D-M9 D-M9V B D-9 D-9V B D-P3DW B Note) djust the auto switch after confiring the operating conditions in the actual setting. uto Switch Mounting Height uto switch odel 2 D-9V Hs Ht 7. 3 D-M9V D-M9WV D-M9V Hs Ht 74. D-P3DW Hs Ht

26 Miniu Stroke for uto Switch Mounting uto switch odel D-9 D-9V D-M9V D-M9 D-M9W D-M9WV D-M9V D-M9 D-P3DW No. of auto switches ounted pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. pc. 2 pcs. ø ø ø ø2 ø ø ø ø ø Note ) Note ) Note ) Note ) Note 2) Note 2) Note 2) Note 2) Note 2) Note ) Confir that it is possible to secure the iniu bending radius of of the auto switch lead wire before use. Note 2) Confir that it is possible to securely set the auto switch(es) within the range of indicator green light ON range before use. For in-line entry type, please also consider Note ) shown above. Note 3) The D-P3DW can be ounted on bore sizes ø to ø. Note 4) s available with end-lock are ø to ø. uto Switch Mounting Series MGP Operating Range uto switch odel D-9/9V D-M9/M9V D-M9W/M9WV D-M9/M9V Values which include hysteresis are for guideline purposes only, they are not a guarantee (assuing approxiately ±3% dispersion) and ay change substantially depending on the abient environent. Please consult SMC for agnetic field resistant auto switch D-P3DW Other than the applicable auto switches listed in How to Order, the following auto switches are ountable. Refer to pages 79 to 27 in Best Pneuatics No. 3 for detailed specifications. Type Model lectrical entry Features Solid state D-P4DW Groet (In-line) Diagnostic indication (2-color display) : ø to ø With pre-wired connector is also available for solid state auto switches. For details, refer to pages 74 and 7 in Best Pneuatics No. 3. Norally closed (NC = b contact) solid state auto switches (D-F9G/F9H) are also available. For details, refer to page 74 in Best Pneuatics No. 3. When installing the D-P4DW, use the BMG7- auto switch ounting bracket. 23

27 Series MGP uto Switch Mounting Brackets/Part No. pplicable Cylinder Series:, MGP, MGP pplicable auto switches uto switch ounting bracket part no. uto switch ounting bracket fitting parts lineup/weight D-M9/M9V D-M9W/M9WV D-M9/M9V D-9/9V ø to ø Surfaces with auto switch ounting slot D-P3DW ø2 to ø BQ-S Hexagon socket head cap screw (M2. x ) uto switch ounting bracket (nut) Weight: g Surfaces with auto switch ounting slot uto switch ounting surfaces Mounting of auto switch uto switch ounting screw uto switch When tightening the auto switch ounting screw, use a watchakers screwdriver with a handle to in diaeter. Tightening Torque for uto Switch Mounting Screw uto switch odel Tightening torque D-M9(V).37 to. lbf ft D-M9W(V) D-M9(V) (. to. N ).74 to. lbf ft D-9(V) (. to. N ) q Fix the auto switch and the auto switch ounting bracket teporarily by tightening the attached hexagon socket head cap screw (M2. x 9. ) to 2 turns. w Insert the teporarily tightened ounting bracket into the ating groove of the cylinder tube, and slide the auto switch onto the cylinder tube through the groove. Insert the auto switch onto the cylinder/actuator through the groove with the back part of the auto switch (lead wire side) and the back part of the auto switch ounting bracket. e Check the detecting position of the auto switch and fix the auto switch firly with the hexagon socket head cap screw (M2. x, M2. x 9. ). r If the detecting position is changed, go back to step w. The hexagon socket head cap screw (M2. x ) is used to fix the ounting bracket and cylinder tube. This enables the replaceent of the auto switch without adjusting the auto switch position. Note ) nsure that the auto switch is covered with the ating groove to protect the auto switch. Note 2) The tightening torque for the hexagon socket head cap screw (M2. x, M2. x 9. ) is.2 to.3 N. Note 3) Tighten the hexagon socket head cap screws evenly. (with auto switch) Hexagon socket head cap screw (M2. x 9. ) Hexagon socket head cap screw (M2. x ) BQ-S uto switch ounting bracket Note) uto switch ounting brackets and auto switches are enclosed with the cylinder for shipent. For an environent that needs the water-resistant auto switch, select the D-M9(V) type.

28 Prior to Use uto Switch Connection and xaple Sink Input Specifications Source Input Specifications 3-wire, NPN Input 3-wire, PNP Input uto switch Black COM (PC internal circuit) uto switch Black COM (PC internal circuit) 2-wire Input 2-wire COM uto switch uto switch COM Input (PC internal circuit) (PC internal circuit) Connect according to the applicable PC input specifications, as the connection ethod will vary depending on the PC input specifications. xaple of ND (Series) and OR (Parallel) Connection When using solid state auto switches, ensure the application is setup so the signals for the first s are invalid. 3-wire ND connection for NPN output (Using relays) Relay oad Black uto switch (Perfored with auto switches only) Black oad uto switch 3-wire OR connection for NPN output uto switch Black oad uto switch 2 Black uto switch 2 Black uto switch 2 Black 3-wire ND connection for PNP output (Using relays) Relay Black uto switch (Perfored with auto switches only) Black uto switch 3-wire OR connection for PNP output Black uto switch uto switch 2 Black oad uto switch 2 Black oad uto switch 2 Black oad 2-wire ND connection uto switch uto switch 2 oad When two auto switches are connected in series, a load ay alfunction because the load voltage will decline when in the ON state. The indicator lights will light up when both of the auto switches are in the ON state. uto switches with load voltage less than V cannot be used. oad voltage at ON = Power supply voltage Residual voltage x 2 pcs. = V 4 V x 2 pcs. = V xaple: Power supply is VDC Internal voltage drop in auto switch is 4 V. 2-wire OR connection uto switch uto switch 2 oad (Solid state) When two auto switches are connected in parallel, alfunction ay occur because the load voltage will increase when in the OFF state. oad voltage at OFF = eakage current x 2 pcs. x oad ipedance = x 2 pcs. x 3 kω = V xaple: oad ipedance is 3 kω. eakage current fro auto switch is. (Reed) Because there is no current leakage, the load voltage will not increase when turned OFF. However, depending on the nuber of auto switches in the ON state, the indicator lights ay soeties grow di or not light up, due to the dispersion and reduction of the current flowing to the auto switches. 2

29 Series MGP Siple Specials These changes are dealt with Siple Specials Syste. Refer to Best Pneuatics No. 3 for details. Change of Guide Rod nd Shape Made to Order Sybol -X//7/2 pplicable Series Series Model MGP Standard MGP MGP Bearing type Ball bushing High precision ball bushing Sybol for change of guide rod end shape -X,, 7, 2 -X, Precautions nsure that the cylinder s overall length should not exceed the allowable overall length. In the case of exceeding the allowable overall length, it will be available as specials. In fig. (), (2) below, diension cannot ake it into diension or less of the standard products. Confir by referring to catalog. SMC will ake appropriate arrangeents if no diension, tolerance, or finish instructions are given in the diagra. diension should be the guide rod diaeter (D) 2. In the case that the preferred diension is different, fill in that diension., llowable overall length of cylinder 34 Overall length of cylinder Fig. () For X, X Overall length of cylinder Fig. (2) For X7, X2 to to, 3 Guide Rod nd Shape Pattern -X -X MM (Standard body diension) 3 Note) Chafer of the guide rod end shape for the MGP is C., not 3. (Standard body diension) 3 Note) Chafer of the guide rod end shape for the MGP is C., not 3. -X7 -X2 MM D MM (Standard body diension) 3 (Standard body diension) 3 T 2

30 Siple Specials Series MGP 2 Machining Tapped Hole, Drilled Hole and Pin Hole dditionally Sybol -XC79 This siple special is eant for achining additionally tapped hole, drilled hole, and pin hole, as requested fro custoer, on parts designed largely for ounting a workpiece etc. in the cobined air cylinders. But, for each odel, since there are soe areas where additional achining is not allowed, so please refer to the additional achining restriction section below. pplicable Series Series Model MGP Standard MGP MGP Bearing type Ball bushing High precision ball bushing Coponent parts applicable for additional achining Plate Precautions We cannot take any responsibility as for the intensity of holes achined additionally and the effects of decreased intensity for the product itself. reas where additional achining was done will not be plated again. Be sure to fill in through for through-hole, and effective depth for blind hole. When using by achining through-hole additionally, ensure that the tip of the bolt etc. for ounting workpiece should not stick into the cylinder side. It ay result in an unexpected proble. Use caution not to interfere the existing ounting hole on the standard products with the hole to be achined additionally. But it is possible to drill additionally the larger size of hole at the sae position as the existing hole. Suppleentary xplanation/holes which can be additionally achined are the following 3 types. Tapped hole Drilled hole Pin hole Designated noinal diaeter and tapped hole of a pitch are achined additionally. (Maxiu noinal thread diaeter M) Blind hole is deep into the botto of prepared hole which sus up to C in the figure below in contrast to the effective depth of tapped hole. When there is a condition which does not allow through-hole etc., leave sufficient thickness in the inner part of hole. D (Thread size) Drilled hole of a designated internal diaeter is achined. (Maxiu hole diaeter ) If you wish for blind hole, instruct us with effective depth. (Refer to the figure below) Besides, diensional accuracy for internal diaeter will be ±.2. D Pin hole of a designated diaeter (reaer hole) is achined. (Maxiu hole diaeter ) Internal diension tolerates H7 tolerance to the designated hole diaeter. (Refer to the table below.) Hole dia. Tolerance 3 or less +. Over 3 to +. DH7 Over to +. Over to Over to (ffective thread depth) B = 3 x P (Incoplete thread section) (ffective depth) (ffective depth) C =.3 x (D P) Note) P stands for thread pitch. C =.3D dditional Machining Restriction/Since the slant lines denote the additional achining restriction section, design the diensions, referring to below. Plate aterial: Steel Mounting side C (Reference) Top connecting port side B Diension of areas where additional achining is not allowed B C

31 3 Series MGP Made to Order Please contact SMC for detailed diensions, specifications and lead ties. Heat Resistant Cylinder (4 to 32 F ( to C)) Made to Order Sybol -XB ir cylinder which changed the seal aterial and grease, so that it could be used even at higher teperature up to fro 4 F ( C). How to Order Standard odel no. XB pplicable Series Series MGP Standard Model Bearing type Note Specifications bient teperature range Seal aterial Grease Specifications other than above and external diensions Warning Precautions 4 Interediate Stroke (Using exclusive body) WB W + Stroke Sybol -XB Cylinder which can reduce the ounting space by using an exclusive body which does not use a spacer to achieve that the full length diension could be shortened when an interediate stroke other than the standard stroke is required. How to Order pplicable Series MGP M Series Model Standard odel no. XB MGP Standard MGP Interediate stroke MGP Specifications: Sae as standard type Diensions: Series MGP /, Diensions to 74 st 7 to 99 st to 74 st to 74 st Heat resistant cylinder Stroke Range,, 2,,,, 7 to 99 st to 99 st to 9 st to 399 st 9. to 399 st to 32 F ( to C) Fluororubber Heat resistant grease Sae as standard type Stroke range to 9 2 to to 399 to 74 st 2 to 74 st 2 to 74 st to 99 st.. Diensions except entioned above are the sae as standard type. 7 to 99 st. 7 to 99 st to 9 st. 4. to 399 st 7 to 399 st Bearing type Ball bushing High precision ball bushing, MGP, MGP/W, WB Diensions Stroke range W WB to 39 st 4 to 99 st to 99 st to 9 st to 39 st 4 to 99 st to 99 st to 9 st 2 to Note ) Operate without lubrication fro a pneuatic syste lubricator. Note 2) Please contact SMC for details on the aintenance intervals for this cylinder, which differ fro those of the standard cylinder. Note 3) In principle, it is ipossible to ake built-in agnet type and the one with auto switch. But, as for the one with auto switch, and the heat resistant cylinder with heat resistant auto switch, since it will be differed depending on the series, please contact SMC. Note 4) Piston speed is ranged fro to /s. But, MGP,, it will be to /s. Be aware that soking cigarettes etc. after your hands have coe into contact with the grease used in this cylinder can create a gas that is hazardous to huans. 2 Specifications except the stroke range are the sae as standard. Note) pplicable stroke available by the interval. Stroke range 2 to 399 Stroke range 2 to to 39 st 4 to 4 st to 49 st to 4 st W to 99 st W to 99 st to 299 st to 299 st 2 MGP, MGP/, Diensions to 39 st 4 to 99 st WB Note 3 to 399 st 2 to 39 st 4 to 4 st to 99 st to 299 st WB 3 to 399 st 2 to 49 st to 4 st to 99 st to 299 st to 9 st to 39 st 3 4 to 99 st to 399 st to 399 st to 9 st to 39 st 4 to 4 st to 99 st to 399 st 2 to 39 st 4 to 4 st to 99 st to 399 st 2 to 74 st to 49 st to 4 st to 74 st. 4. to 99 st to 399 st to 99 st to 399 st to 74 st to 49 st 3. 7 to 4 st to 74 st to 99 st to 399 st to 99 st to 399 st

32 Made to Order Series MGP ow Speed Cylinder ( to /s) ven if driving at lower speeds to /s, there would be no stick-slip phenoenon and it can run soothly. Sybol -XB3 pplicable Series MGP Series Standard Model MGP Bearing type Ball bushing Note How to Order MGP M Standard odel no. XB3 Specifications Piston speed Diensions Specifications other than above ow speed cylinder to /s Sae as standard type Sae as standard type Note ) Operate without lubrication fro a pneuatic syste lubricator. Note 2) For the speed adjustent, use speed controllers for controlling at lower speeds. (Series S-FM/S-M) Warning Operating Precautions Be aware that soking cigarettes etc. after your hands have coe into contact with the grease used in this cylinder can create a gas that is hazardous to huans. Made of Stainless Steel Suitable for the cases it is likely to generate rust by being iersed in the water and corrosion. Sybol -XC pplicable Series MGP Series Standard Model MGP Bearing type Ball bushing Note How to Order qpiston rod yretaining ring MGP M Standard odel no. Made of stainless steel XC wguide rod eplate B Suffix Iron parts ade of stainless steel Rods ade of stainless steel Specifications Parts changed to stainless steel B q, w, e, r, t, y q, w, t, y Specifications other than above and external diensions Sae as standard type rplate ounting bolt thexagon socket head plug 29

33 Series MGP 7 Flourorubber Seals Sybol -XC22 pplicable Series MGP Series Standard Model Bearing type Note How to Order Standard odel no. XC22 Specifications Seal aterial bient teperature range Specifications other than above and external diensions Fluororubber seals Fluororubber With auto switch : 4 to F ( to C) (No freezing) Without auto switch : 4 to F ( to 7 C) Sae as standard type Note ) Please contact SMC, as the type of cheical and the operating teperature ay not allow the use of this product. Note 2) Cylinders with auto switches can also be produced; however, auto switch related parts (auto switch units, ounting brackets, built-in agnets) are the sae as standard products. Before using these, please contact SMC regarding their suitability for the operating environent. Note 3) The MGP series are without a cushion. Confir the kinetic energy. Botto Mounting Type Since the guide rod does not protrude fro the botto at the retraction of the rod, relief holes for guide rods are not required. Sybol -XC2 How to Order MGP M Z XC2 Copact Guide Cylinder Bearing type M 2 2 Cylinder stroke to 2 to uto switch Suffix for auto switch pplicable stroke 7, 2,, 7, Botto ounting type 3 Sae as the standard -Z cylinder Guide rod ZZ Cylinder ounting side Note) The total length (ZZ) of the guide rod bushing is shorter than the standard type.

34 Made to Order Series MGP 9 Syetrical Port Position Sybol -X44 Ports are ounted syetrically. pplicable Series MGP Series Standard Model MGP MGP Bearing type Ball bushing High precision ball bushing Note How to Order MGP M Standard odel no. X44 Syetrical port position Standard This akes it easy to reove and rotate piping when it is ounted on a wall where ounting space is liited. -X44 Diensions (Diensions other than listed below are the sae as standard type.) P + Stroke G 2 x P (Plug) PB, MGP, MGP Coon Diensions G P PB Side Porting Type (Plug location changed) Ports on the top plugged in order to use the piping port on the side. pplicable Series MGP Series Standard Model MGP MGP Bearing type Ball bushing High precision ball bushing Note Sybol -X7 How to Order MGP M Standard odel no. X7 Side porting type (Plug location changed) Hexagon socket head plug Piping port on the front face Piping port on the side face 3

35 Safety Instructions Caution: Warning: Danger : Caution indicates a hazard with a low level of risk which, if not avoided, could result in inor or oderate injury. Warning indicates a hazard with a ediu level of risk which, if not avoided, could result in death or serious injury. Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. These safety instructions are intended to prevent hazardous situations and/or equipent daage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger. They are all iportant notes for safety and ust be followed in addition to International Standards (ISO/IC) ), and other safety regulations. ) ISO 444: Pneuatic fluid power General rules relating to systes. ISO 443: Hydraulic fluid power General rules relating to systes. IC 4-: Safety of achinery lectrical equipent of achines. (Part : General requireents) ISO 2-: Manipulating industrial robots Safety. etc. Warning. The copatibility of the product is the responsibility of the person who designs the equipent or decides its specifications. Since the product specified here is used under various operating conditions, its copatibility with specific equipent ust be decided by the person who designs the equipent or decides its specifications based on necessary analysis and test results. The expected perforance and safety assurance of the equipent will be the responsibility of the person who has deterined its copatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalog inforation, with a view to giving due consideration to any possibility of equipent failure when configuring the equipent. 2. Only personnel with appropriate training should operate achinery and equipent. The product specified here ay becoe unsafe if handled incorrectly. The assebly, operation and aintenance of achines or equipent including our products ust be perfored by an operator who is appropriately trained and experienced. 3. Do not service or attept to reove product and achinery/ equipent until safety is confired.. The inspection and aintenance of achinery/equipent should only be perfored after easures to prevent falling or runaway of the driven objects have been confired. 2. When the product is to be reoved, confir that the safety easures as entioned above are ipleented and the power fro any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully. 3. Before achinery/equipent is restarted, take easures to prevent unexpected operation and alfunction. 4. Contact SMC beforehand and take special consideration of safety easures if the product is to be used in any of the following conditions.. Conditions and environents outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2. Installation on equipent in conjunction with atoic energy, railways, air navigation, space, shipping, vehicles, ilitary, edical treatent, cobustion and recreation, or equipent in contact with food and beverages, eergency stop circuits, clutch and brake circuits in press applications, safety equipent or other applications unsuitable for the standard specifications described in the product catalog. 3. n application which could have negative effects on people, property, or anials requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a echanical protective function, and periodical checks to confir proper operation. Caution. The product is provided for use in anufacturing industries. The product herein described is basically provided for peaceful use in anufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary. If anything is unclear, contact your nearest sales branch. iited warranty and Disclaier/ Copliance Requireents The product used is subject to the following iited warranty and Disclaier and Copliance Requireents. Read and accept the before using the product. iited warranty and Disclaier. The warranty period of the product is year in service or. years after the product is delivered, whichever is first. 2) lso, the product ay have specified durability, running distance or replaceent parts. Please consult your nearest sales branch. 2. For any failure or daage reported within the warranty period which is clearly our responsibility, a replaceent product or necessary parts will be provided. This liited warranty applies only to our product independently, and not to any other daage incurred due to the failure of the product. 3. Prior to using SMC products, please read and understand the warranty ters and disclaiers noted in the specified catalog for the particular products. 2) Vacuu pads are excluded fro this year warranty. vacuu pad is a consuable part, so it is warranted for a year after it is delivered. lso, even within the warranty period, the wear of a product due to the use of the vacuu pad or failure due to the deterioration of rubber aterial are not covered by the liited warranty. Copliance Requireents. The use of SMC products with production equipent for the anufacture of weapons of ass destruction (WMD) or any other weapon is strictly prohibited. 2. The exports of SMC products or technology fro one country to another are governed by the relevant security laws and regulations of the countries involved in the transaction. Prior to the shipent of a SMC product to another country, assure that all local rules governing that export are known and followed. dition B Revision history ddition of Made to Order: Change of guide rod end shape (-X), interediate stroke (-XB), low speed cylinder (-XB3), and side porting type (-X7), etc. are set additionally. RP Safety Instructions Be sure to read Handling Precautions for SMC Products (M-3-3) before using. SMC Corporation of erica SMC Blvd., Noblesville, IN 4 SMC Pneuatics (Canada) td. () SMC.SMC (72-72) e-ail: sales@scusa.co For International inquiries: 3 SMC Corporation of erica, ll Rights Reserved. RS-RRD-M ll reasonable efforts to ensure the accuracy of the inforation detailed in this catalog were ade at the tie of publishing. However, SMC can in no way warrant the inforation herein contained as specifications are subject to change without notice.