Rack & Pinion Type/Size: 30, 50, 63, 80, 100. Compact auto switches are mountable. (D-M9 ) Rotating angle. Rotating. angle

Transcription

1 Rotary Actuator Series Rack & Pinion Type/: 3, 5, 63, 8, 1 Compact auto switches are mountable. (D-M9 ) Width reduced by up to 14 mm Space saving by changing the auto switch rail mounting to groove mounting. Current model Mountable on 2 surfaces. Compact auto switch RoHS RoHS X X Auto switch can be mounted from the front. Auto switch can be mounted from the front at any position on the mounting groove. Auto switch can be mounted after installation or when installation condition is changed. Mounting bracket Weight is reduced by up to 14 %. Lightweight body by changing the body and the cover shape. [kg] Current model [kg] Reduction rate [%] Mounting interchangeable with the current model Standard type : 3, 5, 63, 8, 1 Rotating angle 3 9, 18 5 to 1 9, 18, 1, 19 Angle adjustable type : 5, 63, 8, 1 Rotating 5 to 1 angle 9, 18, 1, 19 With solenoid valve : 5, 63, 8, 1 Rotating 5 to 1 angle 9, 18, 1,

2 Rotary Actuator Series 3, 5, 63, 8, 1 Standard type Cushion seal is replaceable. Cushion seal has been made replaceable. (Not possible for current model. Cushion seal only) Replacement parts Slider Tube gasket Piston seal Spring pin Cushion seal (New) Interchangeable with current model Exterior dimension, shaft diameter, and mounting dimension are interchangeable with current model. Rotating angle to 1 Compact auto switches are mountable. Solid state auto switch D-M9 D-M9 W Reed auto switch D-A9 Easy adjustment of cushion valve Cushion valve shape is changed so it can be adjusted using a hexagon wrench only. No protrusion from the body. Retaining ring is used to prevent drop-out. Mountable on 2 surfaces. Auto switches can be mounted in two rows. 3 Auto switch Port, cushion valve and auto switch are on the same surface. Easy to handle. Cushion valve cannot be mounted on the air-hydro type. With cushion valve retaining ring Auto switches can be mounted in two rows. 5 to 1 Auto switches can be mounted in two rows. Auto switch 184 Port 3

3 Rotary Actuator Series 3, 5, 63, 8, 1 Many variations of shaft type Single shaft: BS Double shaft: BW Current model Standard : 2 types Semi-standard : 6 types Series Standard: 8 types Shaft type can be selected to suit the specification. Part number is assigned for shaft types <single round shaft, double shaft (round shaft, with four chamfers), double round shaft>. Single shaft with four chamfers: BX Double shaft with key: BY Double shaft with four chamfers: BZ Single round shaft: BT Double shaft (round shaft, with four chamfers): BJ Double round shaft: BK Single round shaft, double shaft (round shaft, with four chamfers), double round shaft are made to order. Mounting suitable for operating conditions is possible. Foot bracket can be mounted at a desired position. (Foot bracket is included in the rotary actuator at shipment.) Bottom side Shaft side Port side Back side X X Angle adjustable type Angle can be adjusted to a desired level in a range of up to 9. Angle can be adjusted to an appropriate level suitable for applications. A port B port Adjusting direction Adjusting direction Rotation range of keyway 9 Rotation range of keyway 18 With solenoid valve Solenoid valve and rotation speed adjustment New function are integrated. Part number is set for the angle adjustable type. Angle adjusting screw With solenoid valve Rotation speed adjustment function 185

4 Rotary Actuator Series 3, 5, 63, 8, 1 Standard type Angle adjustable type With solenoid valve Series Variations Type Pneumatic Air-hydro V V V V V V V V V Rotating angle 1 V V V V V V V V 18 V V V V V V V V V 19 V V V V V V V V Single shaft S V V V V V V V V V Double shaft W V V V V V V V V V Single shaft with four chamfers X V V V V V V V V V Standard Shaft type Double shaft with key Y V V V V V V V V V Double shaft with four chamfers Z V V V V V V V V V Single round shaft T V V V V V V V V V Cushion Variations Mounting bracket Pattern Double shaft (round shaft, with four chamfers) J V V V V V V V V V Double round shaft K V V V V V V V V V None V V V V V V V V V Air cushion V V V V V With auto switch V V V V V V V V V Angle adjustable type V V V V With solenoid valve V V V V Clean series Note) 11- V V Flange F V V V V V V V V Foot L V V V V V V V V V Shaft type pattern V V V V V V V V V Rotation range V V V V V V V V Made to Order Port location V V V V V V V V V Stainless steel shaft/bolt/parallel key -X 6 V V V V V Operating temperature Heat resistant 1 C -X 7 V V V V V Both sides angle adjustable -X1 V V V V One side angle adjustable, One side with cushion -X11 V V V V Fluororubber seal -X16 V V V V V Note) For further specifications, refer to Pneumatic Clean Series (CAT.E2-23) catalog. 186

5 CONTENTS Rotary Actuator Series PRotary Actuator Series How to Order Page 188 Specifications Page 189 Dimensions Page 19 Construction Page 196 PRotary Actuator: Angle Adjustable Type llu Series How to Order Page 198 Specifications Page 199 Dimensions Page 2 Construction Page 21 PRotary Actuator with Solenoid Valve CVRA1 Series How to Order Page 22 Specifications Page 24 Dimensions Page 25 Construction Page 26 PAuto Switch Mounting Page 28 X X PSimple Specials/Made to Order Simple specials Shaft pattern sequencing 1 -XA1 to -XA24 Page 212 Shaft pattern sequencing 2 -XA33 to -XA59 Page 216 Made to Order How to Order Page 221 qreversed shaft -XC7 Page 222 wchange of rotation range -XC8 to -XC11 Page 222 echanged to fluorine grease -XC3 Page 222 rchange of rotation range and shaft rotation direction -XC31 to XC36 Page 223 tchange of rotation range and angle adjusting direction -XC37 to XC42 Page 224 ychange of rotation range and angle adjusting direction -XC43 to XC46 Page 225 uchange of rotation range and angle adjusting direction (Angle adjusting screw is equipped on the left.) -XC47 to XC52 Page 226 ichange of rotation range and angle adjusting direction (Angle adjusting screw is equipped on the left.) -XC53 to XC58 Page 227 ochange of port location (Mounting location of the cover is changed.) -XC59 to XC61 Page 228!One side air-hydro, One side air -XC63, -XC64 Page 228!1Stainless steel shaft/bolt/parallel key -X6 Page 229!2Heat resistant -X7 Page 229!3Both sides angle adjustable -X1 Page 229!4One side angle adjustable, One side with cushion -X11 Page 23!5Fluororubber seal -X16 Page 23 Made to Order/-X6 to -X16 Page 231 Specific Product Precautions Page

6 Rotary Actuator Series RoHS Rack & Pinion Type/: 3, 5, 63, 8, 1 With auto switch CDRA1 Mounting B Basic type L Foot type * F Note) Flange type Built-in magnet S W How to Order B S 5 9 Z Shaft type Single shaft Double shaft * For foot bracket and X Single shaft with four chamfers part number, refer to Y Double shaft with key page 189. Z Double shaft with four chamfers * Foot bracket is included in the same package, (but not assembled). Note) Except size 3 T J K Single round shaft Double shaft (round shaft, with four chamfers) Double round shaft * Flange type is not available for T, J, K. * T, J, K are made to order. Type Nil Pneumatic H* Air-hydro * Except size 3. Refer to page 232 for handling precautions Port type Air cushion Nil None C* With air cushion * Except air-hydro type Rotating angle * 1 19* 19 * Except size 3 Applicable Auto Switches/Refer to pages 797 to 85 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnosis indication (2-color indicator) Water resistant (2-color indicator) Electrical entry Indicator light Wiring (Output) Number of auto switches Nil 2 pcs. S 1 pc. * Up to two auto switches are mountable. Auto switch Nil M thread M5 Nil Rc TF G 1/8 1/8 1/4 3/8 TN NPT TT NPTF Load voltage Auto switch model Lead wire length [m] DC AC Perpendicular In-line.5 (Nil) 1 (M) 3 (L) Without auto switch (Built-in magnet) * For applicable auto switch model, refer to the table below. 5 (Z) Pre-wired connector Made to Order Refer to page 189. Applicable load 3-wire (NPN) M9NV M9N V V V v v 5 V, 12 V IC circuit 3-wire (PNP) M9PV M9P V V V v v 2-wire 12 V M9BV M9B V V V v v 3-wire (NPN) M9NWV M9NW V V V v v 5 V, 12 V IC circuit Grommet Yes 3-wire (PNP) 24 V M9PWV M9PW V V V v v 2-wire 12 V M9BWV M9BW V V V v v 3-wire (NPN) M9NAV*1 M9NA*1 v v V v v 5 V, 12 V IC circuit 3-wire (PNP) M9PAV*1 M9PA*1 v v V v v 2-wire 12 V M9BAV*1 M9BA*1 v v V v v 3-wire 5 V A96V A96 V V IC circuit Yes (NPN equivalent) Grommet 1 V A93V*2 A93 V V V V Relay, 2-wire 24 V 12 V No 1 V or less A9V A9 V V IC circuit PLC *1 Although it is possible to mount water resistant type auto switches, note that the rotary actuator itself is not of water resistant construction. *2 1 m type lead wire is only applicable to D-A93. * Lead wire length symbols:.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ * Auto switches marked with v are produced upon receipt of order. * Auto switches are shipped together, (but not assembled). 188 B S 5 9 Z M9BW Relay, PLC * Refer to pages 837 and 838 for detailed solid state auto switches with prewired connectors.

7 Rotary Actuator Rack & Pinion Type Series Angle adjustment range ±3 Flange type Made to Order (For details, refer to pages 211 to 231.) Description Applicable shaft type -XA1 to -XA24 Shaft pattern sequencing! S, W, Y -XA33 to -XA59 Shaft pattern sequencing@ X, Z, T, J, K -XC7 Reversed shaft S, W, X, T, J -XC8 to -XC11 Change of rotation range S, W, Y Changed to fluorine S, W, X, Y, -XC3 grease Z, T, J, K Change of rotation range -XC31 to -XC36 S, W, Y and shaft rotation direction S, W, X, Y, -XC59 to -XC61 Change of port direction Z, T, J, K -XC63, -XC64 -X6 Basic type A port Angle adjustment range ±3 One side air-hydro, One side air Stainless steel shaft/ bolt, etc. A port B port Key B port Key Rotation range of keyway Rotation range of keyway 19 Foot type +4 Angle adjustment range ±3 +4 S, W, X, Y, Z, T, J, K S, W, X, Y, Z, T, J, K S, W, X, Y, -X7* Heat resistant (1 C) Z, T, J, K S, W, X, Y, -X16 Fluororubber seal Z, T, J, K * -X7: Not available for the built-in magnet type Rotation Range of Keyway The shaft rotates clockwise when the pressure is applied from the A port while it rotates counterclockwise when the pressure is applied from the B port. : 3 : 5 to 1 +4 Rotation range of keyway 1 Angle adjustment range ±3 Rotation range of keyway 18 Specifications Type Pneumatic Air-hydro Fluid Air (Non-lube) Turbine oil Max. operating pressure 1. MPa Min. operating pressure.1 MPa Ambient and fluid temperature to 6 C (No freezing) Cushion Not attached, Air cushion None Backlash None * Within 1 Tolerance in rotating angle to +4 * Since the l3 has a stopper installed, there is no backlash produced under pressure. Effective Torque [N m] Operating pressure [MPa] Allowable Kinetic Energy/Adjustable Range of Rotation Time Safe in Operation Allowable kinetic energy [J] Adjustable range of rotation Without air cushion With air cushion * time safe in operation [s/9 ] to to 2 Cushion angle to to to 5 * Allowable kinetic energy of the product with air cushion is the maximum absorbed energy when the cushion valve adjustment is optimized. Weight Standard weight Additional weight 9 18 With auto switch * Foot bracket Flange bracket * With 2 auto switches Foot Bracket/Part No. Foot bracket Contents Mounting screw size included in foot bracket 3 L 3-Y-1Z M 5 x.8 x 25 5 L 5-Y-1Z Foot bracket : 2 pcs. M 8 x 1.25 x L 63-Y-1Z Mounting screw : 4 pcs. M1 x 1.5 x 4 8 L 8-Y-1Z Collar * : 4 pcs. M12 x 1.75 x 5 1 L1-Y-1Z M12 x 1.75 x 5 * 3 does not include collars. * Remove the basic type mounting screws and use the mounting screws included in the foot bracket to secure the foot bracket to the cover. Use the collar as a spacer for the cover counterbore part and secure it together with the foot. * For size 3, be careful not to drop the cover when removing the basic type mounting screws. Additionally, do not mount the foot bracket with the pressure applied to the port. [kg] 189 X X

8 Series Dimensions/Basic Type: ClRA1BS : 3 Single shaft: ClRA1BS Auto switch 28 8 x M5 x.8 depth 6 (Opposite side 4 locations) ø16.1 ø8g6 Double shaft: ClRA1BW 2 x Cushion valve (Width across flats 1.5) 2 x M5 x.8 Port size A port 5.5 B port (117)/With auto switch 84 (13)/Without auto switch 6.2 ø8 (g6) ø7.8.2 Drawing shows the appearance for rotation of 9. Dimensions show pressurization to B port. Drawing shows that the auto switch is mounted on the side opposite to the port side. (Dimensions with an asterisk mark (*) are not required for actuators without the auto switch.) * ( ) are the dimensions for rotation of 18. Note) A parallel key is included in the same package, (but not assembled). 19

9 Rotary Actuator Rack & Pinion Type Series Dimensions/Basic Type: ClRA1BS : 5/63/8/1 Single shaft: ClRA1BS 8 x J (Opposite side 4 locations) CA Auto switch W B 2 x Cushion valve (Width across flats 3) CA F ødd (h9) ød (g6) b L1 K H Double shaft: ClRA1BW CB BC A port BC CB SE SC SD U UU X X BB BA 2 x Port size S B port BA BB SB C A G.2 ød (g6) N M øl.2 ød is the shaft dimension. Note) Other dimensions are the same as the single shaft type. D (g6) G M N UU L Drawing shows the appearance for rotation of 9 and 1. Dimensions show pressurization to B port. Drawing shows the auto switch mounted on the port side. * ( ) are the dimensions for rotation of 18 and 19. Note 1) Port size A B C D DD (g6) (h9) 5 Rc1/ F H J K M depth 8 5 Without With auto switch auto switch U W BA BB BC Note 2) Key dimensions CA CB S SB SC SD SE S b L1 156 (189) 63 Rc1/ M1 1.5 depth (213.5) 8 Rc1/ M depth (243) 1 Rc3/ M depth (325) Note 1) In addition to Rc, G, NPT and NPTF are also available. Note 2) A parallel key is included in the same package, (but not assembled) (177) 163 (21.5) 186 (23) 245 (311) For model with air cushion 191

10 Series Dimensions/Basic Type: ClRA1Bl (Dimensions other than specified below are the same as the standard type.) : 3/5/63/8/1 Single shaft with four chamfers: ClRA1BX Double shaft with key: ClRA1BY Double shaft with four chamfers: ClRA1BZ øl.2 øl.2 G.1 G.1 L H K N M UU UU U U N H H N H G.2 ød øl.2 G H N U L Note) Dimension parts different from the standard conform to the general tolerance. Single round shaft: ClRA1BT ød H K UU L Note) Dimension parts different from the standard conform to the general tolerance. Double shaft (round shaft, with four chamfers): ClRA1BJ ød D (g6) G H M N U UU L Note) Dimension parts different from the standard conform to the general tolerance. Double round shaft: ClRA1BK ød N M UU UU H H H D (g6) H Note) Dimension parts different from the standard conform to the general tolerance. 192 ød G.2 øl.2 D (g6) G H M N UU L Note) Dimension parts different from the standard conform to the general tolerance. H D (g6) H UU Note) Dimension parts different from the standard conform to the general tolerance.

11 Rotary Actuator Rack & Pinion Type Series Dimensions/Foot Type: ClRA1LS : 3 Auto switch 44 A port Foot bracket B port x ø6 (Mounting hole) X X (157)/With auto switch 124(143)/Without auto switch (177)/With auto switch 144(163)/Without auto switch Drawing shows the appearance for rotation of 9. Dimensions show pressurization to B port. Drawing shows that the auto switch is mounted on the side opposite to the port side. * ( ) are the dimensions for rotation of

12 Series Dimensions/Foot Type: ClRA1LS : 5/63/8/1 LF LH LC LA Foot bracket 4 x ølb (Mounting hole) A port B port LD LE LT Drawing shows the appearance for rotation of 9 and 1. Dimensions show pressurization to B port. Drawing shows that the auto switch mounted on the port side. * ( ) are the dimensions for rotation of 18 and 19. Note) Other dimensions are the same as the basic type. LA LB LC With auto switch Without auto switch LF LH LT LD LE LD LE (245) 247 (285.5) 287 (331) 347 (413) 236 (269) 275 (313.5) 329 (373) 389 (455) 2 (233) 235 (273.5) 274 (318) 333 (399) 224 (257) 263 (31.5) 316 (36) 375 (441)

13 Rotary Actuator Rack & Pinion Type Series Dimensions/Flange Type: ClRA1Fl : 5/63/8/1 Single shaft: ClRA1FS Double shaft: ClRA1FW Single shaft with four chamfers: ClRA1FX 2 x MM H N H U ZY FY UU U 4 x øfd (Mounting hole) N F FX ZX U H Note) Other dimensions are the same as the single shaft type. H N U UU Note) Other dimensions are the same as the single shaft type. H N U X X FT Note) Other dimensions are the same as the basic type. F H MM U FD Double shaft with key: ClRA1FY Double shaft with four chamfers: ClRA1FZ M6 x 1. depth H N H M6 x 1. depth 12 M8 x 1.25 depth U UU U UU M1 x 1.5 depth N FT FX FY ZX ZY Note) Other dimensions are the same as the single shaft type. H U UU Note) Other dimensions are the same as the single shaft type. H N U UU The dimensions of shaft key and four chamfers are the same as the basic type. For details, refer to page

14 Series Construction: 3 Without @8!3 e t!4!1 i! q w!2 With Without air cushion With auto switch!7!6!8 Component Parts No. Description Material Note 1 Body Aluminum alloy Anodized 2 Right cover Aluminum alloy Metallic coating 3 Left cover Aluminum alloy Metallic coating 4 Piston Aluminum alloy 5 Shaft Alloy steel 6 Rack Carbon steel Nitrided 7 Slider Resin 8 Bearing retainer Zinc alloy Chromated 9 Tube gasket NBR 1 Piston seal NBR 11 Bearing High carbon chrome bearing steel 12 Hexagon socket head cap screw with washer Alloy steel Zinc chromated 13 Spring pin Steel Zinc chromated 14 Parallel key Carbon steel 15 Cross-recessed pan head tapping screw Steel Zinc chromated 16 Auto switch 17 Magnet 18 Switch spacer Resin 19 Cushion ring Aluminum alloy Anodized 2 Cushion valve Steel Nickel plated 21 Cushion seal Urethane 22 O-ring NBR No. Description Material Note 23 Seal retainer Steel 24 Parallel key Carbon steel 25 Stopper Alloy steel 26 Piston holding bolt Alloy steel Zinc chromated 27 Hexagon socket head set screw Alloy steel Zinc chromated 28 Hexagon nut Steel Zinc chromated 29 O-ring NBR Replacement Parts Part no. Without air cushion With air cushion Air-hydro Note 2) 9 P P P P u, o,!,!3 are u, are Corresponding parts included as a set. included as a set. Note 1) When ordering replacement parts, write 1 for one set of the parts per actuator. Note 2) Replacement parts for different rotation angles are set. A grease pack (1 g) is included. If an additional grease pack is needed, order with the following part number. Grease pack part number: GR-S-1 (1 g) 196

15 Rotary Actuator Rack & Pinion Type Series Construction: 5 to 1 Without air cushion!7 y!3 u!6!2 e o r!5 t With air cushion!4!1 i! q w Without air cushion With auto switch @4 Component Parts No. Description Material Note 1 Body Aluminum alloy Anodized 2 Right cover Aluminum alloy Metallic coating 3 Left cover Aluminum alloy Metallic coating 4 Piston Aluminum alloy 5 Shaft Alloy steel 6 Rack Carbon steel Nitrided 7 Slider Resin 8 Bearing retainer Aluminum alloy Chromated 9 Tube gasket NBR 1 Piston seal NBR 11 Bearing High carbon chrome bearing steel 12 Hexagon socket head cap screw with washer Alloy steel Zinc chromated 13 Spring pin Steel Zinc chromated 14 Parallel key Carbon steel 15 Connecting screw Carbon steel Zinc chromated 16 Cross-recessed pan head tapping screw Steel Zinc chromated 17 Wear ring Resin 18 Auto switch 19 Magnet 2 Switch spacer Resin 21 Cushion ring Aluminum alloy Anodized 22 Cushion valve Steel Zinc chromated 23 Cushion seal Urethane 24 O-ring NBR 25 Seal retainer Steel 26 Retaining ring Steel Replacement Parts Part no. Without air cushion With air cushion Air-hydro 5 P P P P P P P P P P P P Corresponding u, o,!,!3 are u, are u, o,!,!3 are parts included as a set. included as a set. included as a set. Note) When ordering replacement parts, write 1 for one set of the parts per actuator. A grease pack (1 g) is included. If an additional grease pack is needed, order with the following part number. Grease pack part number: GR-S-1 (1 g) 197

16 Rotary Actuator: Angle Adjustable Type (Angle adjustment mechanism is provided as standard.) llu Series Rack & Pinion Type/: 5, 63, 8, 1 RoHS With auto switch CDRA1 Mounting B Basic type L Foot type * F Flange type Built-in magnet * For foot bracket and part number, refer to page 199. * Foot bracket is included in the same package, (but not assembled). S W X Y Z T J K B S U 5 9 Z Shaft type Single shaft Double shaft Single shaft with four chamfers Double shaft with key Double shaft with four chamfers Single round shaft Double shaft (round shaft, with four chamfers) Double round shaft * Flange type is not available for T, J, K. * T, J, K are made to order. Angle adjustable type How to Order Nil Rotating angle Auto switch Without auto switch (Built-in magnet) * For applicable auto switch model, refer to the table below. Port type Number of auto switches Nil 2 pcs. S 1 pc. Note) Up to two auto switches are mountable Nil Rc TF G 1/8 1/4 3/8 TN NPT TT NPTF Applicable Auto Switches/Refer to pages 797 to 85 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnosis indication (2-color indicator) Water resistant (2-color indicator) Electrical entry Indicator light Wiring (Output) Load voltage Auto switch model Lead wire length [m] DC AC Perpendicular In-line.5 (Nil) 1 (M) Made to Order Refer to page (L) 5 (Z) Pre-wired connector Applicable load 3-wire (NPN) M9NV M9N V V V v v 5 V, 12 V IC circuit 3-wire (PNP) M9PV M9P V V V v v 2-wire 12 V M9BV M9B V V V v v 3-wire (NPN) M9NWV M9NW V V V v v 5 V, 12 V IC circuit Grommet Yes 3-wire (PNP) 24 V M9PWV M9PW V V V v v 2-wire 12 V M9BWV M9BW V V V v v 3-wire (NPN) M9NAV*1 M9NA*1 v v V v v 5 V, 12 V IC circuit 3-wire (PNP) M9PAV*1 M9PA*1 v v V v v 2-wire 12 V M9BAV*1 M9BA*1 v v V v v 3-wire 5 V A96V A96 V V IC circuit Yes (NPN equivalent) Grommet 1 V A93V*2 A93 V V V V Relay, 2-wire 24 V 12 V No 1 V or less A9V A9 V V IC circuit PLC *1 Although it is possible to mount water resistant type auto switches, note that the rotary actuator itself is not of water resistant construction. *2 1 m type lead wire is only applicable to D-A93. * Lead wire length symbols:.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ * Auto switches marked with v are produced upon receipt of order. * Auto switches are shipped together, (but not assembled). 198 B S U 5 9 Z M9BW Relay, PLC * Refer to pages 837 and 838 for detailed solid state auto switches with prewired connectors.

17 Rotary Actuator: Angle Adjustable Type Rack & Pinion Type llu Series Specifications Made to Order (For details, refer to pages 211 to 231.) Description Applicable shaft type -XA1 to -XA24 Shaft pattern sequencing! S, W, Y -XA33 to -XA59 Shaft pattern sequencing@ X, Z, T, J, K -XC7 Reversed shaft S, W, X, T, J -XC3 Changed to fluorine grease S, W, X, Y Z, T, J, K Change of rotation range -XC37 to -XC46 S, W, Y and angle adjusting direction Change of rotation range and angle adjusting direction -XC47 to -XC58 S, W, Y (Angle adjusting screw is equipped on the left.) S, W, X, Y -XC59 to -XC61 Change of port direction Z, T, J, K -X7* Heat resistant type (1 C) -X16 Fluororubber seal -X1 Both sides angle adjustable S, W, X, Y Z, T, J, K S, W, X, Y Z, T, J, K S, W, X, Y Z, T, J, K One side angle S, W, X, Y -X11 adjustable, Z, T, J, K One side with cushion * -X7: Not available for the built-in magnet type. Fluid Type Pneumatic Air (Non-lube) Max. operating pressure Min. operating pressure Ambient and fluid temperature Cushion 1. MPa.1 MPa to 6 C (No freezing) None Backlash Within 1 Angle adjustment range Max. 9 * For details about the effective torque, allowable kinetic energy, and adjustable range of rotation time safe in operation, refer to page 189. Weight Standard weight Additional weight 9 18 With auto switch * Foot bracket Flange bracket * With 2 auto switches Rotation Range of Keyway/Angle Adjustment The shaft rotates clockwise when the pressure is applied from the A port. The clockwise rotation end position is adjusted using the angle adjusting screw. Note) Take appropriate measures so that no excessive external impact or vibration is applied to the angle adjusting screw. Failure to do so may cause the angle adjusting screw to become loose or drop. A port Angle adjusting screw B port Rotation range of keyway 18 Rotation range of keyway 1 Rotation range of keyway 19 [kg] X X Adjustment angle per rotation of angle adjusting screw Adjusting angle Foot Bracket/Part No. Foot bracket Contents Mounting screw size included in foot bracket 5 L 5-Y-1Z M 8 x 1.25 x L 63-Y-1Z Foot bracket : 2 pcs. M1 x 1.5 x 4 Mounting screw: 4 pcs. 8 L 8-Y-1Z Collar * : 4 pcs. M12 x 1.75 x 5 1 L1-Y-1Z M12 x 1.75 x 5 * Remove the basic type mounting screws and use the mounting screws included in the foot bracket to secure the foot bracket to the cover. Use the collar as a spacer for the cover counterbore part and secure it together with the foot. 199

18 llu Series Dimensions/Basic Type: ClRA1BSU : 5/63/8/1 Single shaft: ClRA1BSU 8 x J (Opposite side 4 locations) CU (Hexagon width across flats) B W ødd (h9) ød (g6) AU MU BC K 2 x Port size Auto switch SU (Max.) F b SE SC U L1 H A port SD BB BA S B port BA BB SB C A BU (Width across flats) Drawing shows the appearance for rotation of 9 and 1. Dimensions show pressurization to B port. Drawing shows the auto switch mounted on the port side. * ( ) are the dimensions for rotation of 18 and 19. Note 1) Port size A B C D (g6) DD (h9) 5 Rc1/ Rc1/ Rc1/ Rc3/ F H J K M8 x 1.25 depth 8 M1 x 1.5 depth 12 M12 x 1.75 depth 13 M12 x 1.75 depth Without With auto switch auto switch U W BA BB BC S SB SC SD SE S 156 (189) 175 (213.5) 199 (243) 259 (325) (177) 163 (21.5) 186 (23) 245 (311) AU BU CU SU MU Key Note 2) dimensions b L M12 x M14 x M16 x M2 x Note 1) In addition to Rc, G, NPT and NPTF are also available. Note 2) A parallel key is included in the same package, (but not assembled). 2 The dimensions of the shaft type (W: Double shaft, X: Single shaft with four chamfers, Y: Double shaft with key, Z: Double shaft with four chamfers, T: Single round shaft, J: Double shaft (round shaft, with four chamfers), K: Double round shaft), foot type, and flange type are the same as the standard type. For details, refer to pages 191 to 195.

19 Rotary Actuator: Angle Adjustable Type Rack & Pinion Type llu Series Construction!8 @ e! t!1!6 y!5!2 o r q w With @5 Component Parts No. Description Material Note 1 Body Aluminum alloy Anodized 2 Right cover Aluminum alloy Metallic coating 3 Left cover Aluminum alloy Metallic coating 4 Right piston Aluminum alloy 5 Left piston Aluminum alloy 6 Shaft Alloy steel 7 Rack Carbon steel Nitrided 8 Slider Resin 9 Bearing retainer Aluminum alloy Chromated 1 Tube gasket NBR 11 Piston seal NBR 12 Bearing High carbon chrome bearing steel 13 Hexagon socket head cap screw with washer Alloy steel Zinc chromated 14 Spring pin Steel Zinc chromated No. Description Material Note 15 Parallel key Carbon steel 16 Connecting screw Carbon steel Zinc chromated 17 Cross-recessed pan head tapping screw Steel Zinc chromated 18 Wear ring Resin 19 Stopper Carbon steel Zinc chromated 2 Hexagon socket head set screw (flat point) Alloy steel Zinc chromated 21 Hexagon nut Steel Zinc chromated 22 Seal washer NBR 23 O-ring NBR 24 Angle adjusting collar Carbon steel Zinc chromated 25 Auto switch 26 Magnet 27 Switch spacer Resin Replacement Parts Part no. Corresponding parts 5 P P P P are included as a set. Note) When ordering replacement parts, write 1 for one set of the parts per actuator. A grease pack (1 g) is included. If an additional grease pack is needed, order with the following part number. Grease pack part number: GR-S-1 (1 g) 21

20 Rotary Actuator with Solenoid Valve CVRA1 Series RoHS Rack & Pinion Type/: 5, 63, 8, 1 With auto switch CDVRA1 How to Order CVRA1 B S 5 9 Z 1 1 G B S 5 9 Z 1 1 G M9BW Built-in magnet With solenoid valve Mounting B Basic type L Foot type Note) Flange type F is not available. Shaft type S Single shaft W Double shaft X Single shaft with four chamfers Y Double shaft with key Z Double shaft with four chamfers T Single round shaft J Double shaft (round shaft, with four chamfers) K Double round shaft * T, J, K are made to order. Nil U Type Standard Angle adjustable Air cushion Nil None C With air cushion * Except angle adjustable type U. Rotating angle q w e r Nil t Auto switch Without auto switch (Built-in magnet) * For applicable auto switch model, refer to the table below. Number of auto switches Nil 2 pcs. S 1 pc. * Up to two auto switches are mountable. Made to Order Refer to page 24. Applicable Auto Switches/Refer to pages 797 to 85 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnosis indication (2-color indicator) Water resistant (2-color indicator) Electrical entry Indicator light Wiring (Output) Load voltage Auto switch model Lead wire length [m] DC AC Perpendicular In-line.5 (Nil) 1 (M) 3 (L) 5 (Z) Pre-wired connector Applicable load 3-wire (NPN) M9NV M9N V V V v v 5 V, 12 V IC circuit 3-wire (PNP) M9PV M9P V V V v v 2-wire 12 V M9BV M9B V V V v v 3-wire (NPN) M9NWV M9NW V V V v v 5 V, 12 V IC circuit Grommet Yes 3-wire (PNP) 24 V M9PWV M9PW V V V v v 2-wire 12 V M9BWV M9BW V V V v v 3-wire (NPN) M9NAV*1 M9NA*1 v v V v v 5 V, 12 V IC circuit 3-wire (PNP) M9PAV*1 M9PA*1 v v V v v 2-wire 12 V M9BAV*1 M9BA*1 v v V v v 3-wire 5 V A96V A96 V V IC circuit Yes (NPN equivalent) Grommet 1 V A93V*2 A93 V V V V Relay, 2-wire 24 V 12 V No 1 V or less A9V A9 V V IC circuit PLC * 1 Although it is possible to mount water resistant type auto switches, note that the rotary actuator itself is not of water resistant construction. * 2 1 m type lead wire is only applicable to D-A93. * Lead wire length symbols:.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ * Auto switches marked with v are produced upon receipt of order. * Auto switches are shipped together, (but not assembled). 22 Relay, PLC * Refer to pages 837 and 838 for detailed solid state auto switches with prewired connectors.

21 Rotary Actuator with Solenoid Valve Rack & Pinion Type CVRA1 Series q Type of actuation 1 2 position single 2 2 position double 3 3 position closed center 4 3 position exhaust center 5 3 position pressure center e Electrical entry Grommet L-type plug connector w Rated voltage AC specification [5/6 Hz] DC specification 1 1 AC 5 24 VDC 2 2 AC 6 12 VDC 3 11 VAC [115 VAC] 4 22 VAC [23 VAC] 7 24 VAC B 24 VAC M-type plug connector G: Lead wire L: With lead wire M: With lead wire length 3 mm (length 3 mm) (length 3 mm) H: Lead wire length 6 mm G: Lead wire length 3 mm H: Lead wire length 6 mm DC Without light/ surge voltage suppressor LN: Without lead wire LO: Without connector MN: Without lead wire MO: Without connector CE DC compliant AC Note 2) DIN terminal DIN (EN ) terminal Conduit terminal [IP65 compatible] [IP65 compatible] [IP65 compatible] D: With connector Y: With connector DO: Without connector YO: Without connector T: Conduit terminal LN and MN types are with 2 sockets. Refer to the Best Pneumatics No. 1-2 when different length of lead wire for L/M-type plug connector is required. Refer to the Best Pneumatics No. 1-2 for details on the DIN (EN ) terminal. Note 1) When using IP65, select the main/pilot valve common exhaust type or pilot valve base exhaust type. (Except VF1) Note 2) With the same specifications as the DC type, all electrical entries for the 24 VAC type are CE marking compliant. r Light/Surge voltage suppressor Light/Surge voltage suppressor DC AC Nil Without light/surge voltage suppressor S With surge voltage suppressor Note) Z With light/surge voltage suppressor R With surge voltage suppressor (Non-polar) U With light/surge voltage suppressor (Non-polar) Note) S type is not available with AC mode, since a rectifier prevents surge voltage generation. In the DIN terminal type, since a light is installed in the connector, DOZ, DOU, YOZ, YOU are not available. t Manual override Nil: Non-locking push type D: Push-turn locking slotted type E: Push-turn locking lever type X X 23

22 CVRA1 Series Specifications Made to Order (Refer to pages 211 to 231 for details.) Specifications/Description Applicable shaft type S, X, Y, Z, Shaft type variations T, J, K XA1 to XA24 Shaft pattern sequencing! S, W, Y XA33 to XA46 Shaft pattern sequencing@ X, Z, T, J, K XC7 Reversed shaft S, W, X, T, J XC8 to XC11 Change of rotation range S, W, Y S, W, X, Y, XC3 Fluorine grease Z, T, J, K Change of rotation range and XC31 to XC36 S, W, Y rotation direction of shaft Change of rotation range and XC37 to XC46 S, W, Y angle adjusting direction XC47 to XC58 X6 X1 X11 Rotation Range of Keyway Solenoid Valve Mounting Positions SOL.1 Change of rotation range and angle adjusting direction (Angle adjusting screw is equipped on the left.) Stainless steel specifications for main parts Both sides angle adjustable type One side angle adjustable, One side cushion Key Rotation range of keyway 18 Rotation range of keyway 1 Rotation range of keyway S, W, Y S, W, X, Y, Z, T, J, K S, W, X, Y, Z, T, J, K S, W, X, Y, Z, T, J, K Rotary Actuator Type Pneumatic Fluid Air (Non-lube) Max. operating pressure 1. MPa Min. operating pressure.15 MPa Ambient and fluid temperature to 5 C (No freezing) Cushion Not attached, Air cushion Backlash Within 1 Tolerance in rotating angle to +4 Mounting Basic type, Foot type Solenoid Valve Grommet (G), (H) DIN terminal (D) Electrical entry L plug connector (L) DIN (EN ) terminal (Y) M plug connector (M) Conduit terminal (T) Coil rated voltage V AC (5/6 Hz) 24, 1, 11, 2, 22, 24 DC 12, 24 Allowable voltage change 1 to +1% of the rated voltage 24 V 1.5 (With light 1.55) 1.5 (With light 1.75) 1 V Apparent power 11 V [115 V] AC VA 2 V 1.55 (With light 1.65) 1.55 (With light 1.7) 22 V [23 V] 24 V Power consumption W DC Standard 1.5 (With light 1.55) 1.5 (With light 1.75) In common between 11 VAC and 115 VAC, and between 22 VAC and 23 VAC. For 115 VAC and 23 VAC, the allowable voltage is 15% to +5% of rated voltage. Since voltage drops due to the internal circuit in S and Z types, the allowable voltage fluctuation should be within the following range. 24 VDC: 7% to +1% 12 VDC: 4% to +1% Solenoid Valve Weight Single solenoid How to calculate weight Weight = Basic weight + Solenoid valve weight Refer to page 189 for basic weight. Double solenoid How to Adjust the Rotation Speed Rotation direction When current is applied to SOL.1, the shaft rotates clockwise. How to adjust the rotation speed: Turn the needle valve of the metering valve clockwise to reduce the exhaust flow volume, thus slowing the rotation speed. Metering valve A regulates the clockwise rotation speed of the shaft and throttle valve B regulates the counterclockwise speed to the shaft. Type of actuation Closed center B Exhaust center Rotation in the clockwise direction A Pressure center 5 to Metering Valve with Silencer [kg] 24

23 lb Rotary Actuator with Solenoid Valve Rack & Pinion Type CVRA1 Series Dimensions/Basic Type: ClVRA1BS : 5/63/8/1 Single shaft/clvra1bs Angle adjustable type/clvra1bs CB CB CA Auto switch 2 x Cushion valve CA (Width across flats 3) CU (Hexagon width across flats) 8 x J (Opposite side 4 locations) SU (Max.) AU MU SOL.1 W B Rc1/4 (Port size) (Opposite side) ødd (h9) ød (g6) X X SC SE U F H K BA S 49 (Max.) BA VJ VK VH VL SB C A SD Drawing shows the appearance for rotation of 9 and 1. * ( ) are the dimensions for rotation of 18 and 19. Drawing shows that SOL.1 is in the de-energized state. mark shows the dimensions of the solenoid valve VF312K-1G1-2-X14. Drawing shows the auto switch mounted on the port side. A B C D DD (g6) (h9) F H J K M8 x 1.25 depth 8 M1 x 1.5 depth 12 M12 x 1.75 depth 13 M12 x 1.75 depth Without With auto switch auto switch U W BA Valve dimensions Key dimensions Note) CA CB S SB SC SD SE S VH VJ VK VL b l 156 (189) 175 (213.5) 199 (243) 259 (325) Note) A parallel key is included in the same package, (but not assembled). Angle adjustable 144 (177) 163 (21.5) 186 (23) 245 (311) For model with air cushion AU CU SU MU M12 x M14 x M16 x M2 x 2.5 The dimensions of the shaft type (W: Double shaft, X: Single shaft with four chamfers, Y: Double shaft with key, Z: Double shaft with four chamfers, T: Single round shaft, J: Double shaft (round shaft, with four chamfers, K: Double round shaft), foot type, and flange type are the same as the standard type. For details, refer to pages 191 to

24 CVRA1 Series Construction/With Solenoid Valve Without air cushion!7 y!4 #1!9 e o r!6 t!5!1 i! #2 #3 With air cushion #4 #6 #8 #5 #7 #9 Without air cushion With auto switch $1 $ $2 Component Parts No. Description Material Note 1 Body Aluminum alloy Anodized 2 Right cover Aluminum alloy Metallic coating 3 Left cover Aluminum alloy Metallic coating 4 Piston Aluminum alloy 5 Shaft Alloy steel 6 Rack Carbon steel Nitrided 7 Slider Resin 8 Bearing retainer Aluminum alloy Chromated 9 Tube gasket NBR 1 Piston seal NBR 11 Bearing High carbon chrome bearing steel 12 Hexagon socket head cap screw with washer Alloy steel Zinc chromated 13 Cross-recessed pan head tapping screw Steel Zinc chromated 14 Spring pin Steel Zinc chromated 15 Parallel key Carbon steel 16 Connecting screw Carbon steel Zinc chromated 26 Component Parts No. Description Material Note 17 Wear ring Resin 18 Sub-plate Aluminum alloy Chromated 19 Sub-plate (Right cover side) Aluminum alloy Chromated 2 Guide tube fitting Aluminum alloy Chromated 21 Pipe Stainless steel 22 Hexagon socket head cap screw Alloy steel Zinc chromated 23 Hexagon socket head cap screw Alloy steel Zinc chromated 24 Spring washer Alloy steel Zinc chromated 25 O-ring NBR 26 O-ring NBR 27 M5 plug 28 Metering valve with silencer ASN2-l 29 Solenoid valve 3 Sub-plate (Left cover side) Aluminum alloy Chromated 31 Hexagon socket head cap screw Alloy steel Zinc chromated 32 Guide tube fitting (Cover side) Aluminum alloy Chromated

25 Rotary Actuator with Solenoid Valve Rack & Pinion Type CVRA1 Series Construction/Angle Adjustable Type $6 $5 $4 $3 $7 $8 X X Component Parts No. Description Material Note 33 O-ring NBR 34 Cushion ring Aluminum alloy Anodized 35 Cushion valve Steel Zinc chromated 36 Cushion seal Urethane 37 O-ring NBR 38 Seal retainer Steel 39 Retaining ring Steel 4 Auto switch 41 Magnet 42 Switch spacer Resin 43 Stopper Carbon steel Zinc chromated 44 Hexagon socket head set screw (flat point) Alloy steel Zinc chromated 45 Hexagon nut Steel Zinc chromated 46 Seal washer NBR 47 O-ring NBR 48 Angle adjusting collar Carbon steel Zinc chromated Replacement Parts Part no. Without air cushion With air cushion Angle adjustable type 5 P P P P P P P P P P P P Corresponding #3 are included as a #3, #6 are included #3, $6 are included parts set. as a set. as a set. Note) When ordering replacement parts, write 1 for one set of the parts per actuator. A grease pack (1 g) is included. If an additional grease pack is needed, order with the following part number. Grease pack part number: GR-S-1 (1 g) 27

26 Series Auto Switch Mounting Auto Switch Proper Mounting Position at Rotation End : 3 : 5 to 1 Auto switch Auto switch Connection port A A A A * For models with the solenoid valve, the auto switch can be mounted only on the rear side (opposite to the solenoid valve). Perpendicular type auto switch Connection port A For size 3, only the perpendicular type auto switch can be mounted since two auto switches are mounted in the same switch groove when mounting the switch on the connection port side. A Operating range at proper mounting position θ/2 Operating range of single auto switch θ Most sensitive position D-M9l/M9lV D-M9lW/M9lWV Rotating angle D-M9lA/M9lAV Proper mounting position Operating range Proper mounting position A θ [ ] A D-A9l/A9lV Operating range θ [ ] * Values which include hysteresis are for guideline purposes only, they are not a guarantee (assuming approximately ±3% dispersion) and may change substantially depending on the ambient environment. Adjust the auto switch after confirming the operating conditions in the actual setting Switch Spacer/Part No Switch spacer part no. BMY3-16 * The above part number includes one switch spacer. * Two switch spacers are included with the product with built-in magnet. 28

27 Auto Switch Mounting Series Auto Switch Mounting To fix the auto switch, hold the switch spacer, and insert into the groove. Make sure that the switch spacer is in the right position or correct the position if necessary, then slide the auto switch in the groove so that it goes into the spacer. Confirm where the mounting position is, and tighten the auto switch mounting screw using a flat head screwdriver. Auto Switch Working Principle Switch spacer (BMY3-16) Switch mounting screw (Attached to switch) (M2.5 x 4L) Flat head watchmakers screwdriver (Not attached to switch) Note) When tightening an auto switch mounting screw, use a watchmakers screwdriver with a handle of approximately 5 to 6 mm in diameter. Also, tighten with a torque of about.1 to.15 N m. As a guide, turn about 9 past the point at which tightening can first be felt. X X [Pressure is applied from the B port.] The auto switch B is turned ON by the magnet B in the state that the pressure is applied from the B port and the piston B moves to the left side. At this time, the auto switch A turns OFF. Magnet B Piston B A port Auto switch A Auto switch B B port [Pressure is applied from the A port.] When the pressure is applied from the A port, the piston A moves to the right side and the shaft rotates clockwise. The auto switch B turns OFF and the auto switch A is turned ON by the magnet A at the rotation end. Piston A Magnet A Shaft A port Auto switch A Auto switch B B port 29

28 CONTENTS Rotary Actuator Series Simple Specials/Made to Order Simple specials Shaft pattern sequencing 1 -XA1 to -XA24 Page 212 Shaft pattern sequencing 2 -XA33 to -XA59 Page 216 Made to Order How to Order Page 221 qreversed shaft -XC7 Page 222 wchange of rotation range -XC8 to -XC11 Page 222 echanged to fluorine grease -XC3 Page 222 rchange of rotation range and shaft rotation direction -XC31 to XC36 Page 223 tchange of rotation range and angle adjusting direction -XC37 to XC42 Page 224 ychange of rotation range and angle adjusting direction -XC43 to XC46 Page 225 uchange of rotation range and angle adjusting direction X X (Angle adjusting screw is equipped on the left.) -XC47 to XC52 Page 226 ichange of rotation range and angle adjusting direction (Angle adjusting screw is equipped on the left.) -XC53 to XC58 Page 227 ochange of port location (Mounting location of the cover is changed.) -XC59 to XC61 Page 228!One side air-hydro, One side air -XC63, -XC64 Page 228!1Stainless steel shaft/bolt/parallel key -X6 Page 229!2Heat resistant -X7 Page 229!3Both sides angle adjustable -X1 Page 229!4One side angle adjustable, One side with cushion -X11 Page 23!5Fluororubber seal -X16 Page 23 Made to Order/-X6 to -X16 Page

29 Series Simple Specials Shaft shape pattern is dealt with simple made-to-order system. A specification sheet is available for ordering. Please access SMC website, or consult your nearest sales branch. Shaft Pattern Sequencing1 Applicable shaft type: S, W, Y -XA1 to -XA24 How to Order C D RA1 B S 5 9 Z M9BW X A1 A2 C8 C59 Magnet Nil None D Built-in magnet Solenoid valve Nil None V* With solenoid valve * Except size 3, air-hydro type Mounting B Basic type L Foot type Shaft type S Single shaft W Double shaft Y Double shaft with key Auto switch Nil Model with solenoid valve * Refer to page 22 for model number with solenoid valve. Cushion Nil Without air cushion C* With air cushion * Except angle adjustable type, air-hydro type Number of auto switches Nil 2 pcs. S 1 pc. Without auto switch (Built-in magnet) * For applicable auto switch model, refer to page 188. * Auto switches are shipped together, (but not assembled). Variation Nil Without angle adjustment U* Angle adjustable type H* Air-hydro type * Except size Port type M thread M5 Nil Rc TF G 1/8 1/8 1/4 3/8 TN NPT TT NPTF Rotating angle * 1 19* 19 * Except size 3 for simple specials, made-to-order products * Combination of XA is possible for up to 2 types. Combination 3 types Combination of applicable chart A 1 A24 C59 Chart 1, 2 A13 C 8 C59 Chart 2, 7 Combination is available only when all the conditions are fulfilled in the combination chart. Combination 4 types Combination of applicable chart A 1 A 2 C 8 C59 Chart 1, 2, 7 A 2 A24 C1 C6 Chart 1, 2, 7 Combination is available only when all the conditions are fulfilled in the combination chart. * Combination of simple special and made-to-order is possible for up to 4 types. * Above is the typical example of combination. 212

30 Simple Specials Series Shaft Pattern Sequencing1 Applicable shaft type: S, W, Y -XA1 to -XA24 Combination Chart of Simple Specials for Shaft Shape Chart 1. Combination between -XAl and -XAl (S, W, Y shaft) Description Axial direction Applicable shaft type Combination Top Bottom S W Y -XA1 -XA2 -XA13 -XA24 -XA1 Shaft-end female thread V V V V V V -XA2 Shaft-end female thread V V V V V V -XA13 Shaft through-hole V V V V V V -XA14 Shaft through-hole + Shaft-end female thread V V V V V -XA15 Shaft through-hole + Shaft-end female thread V V V V V -XA16 Shaft through-hole + Double shaft-end female thread V V V V V V -XA17 Shorted shaft (Long shaft with key) V V V V V V -XA18 Shorted shaft (Short shaft and with four sided chamfer) V V V W, Y * W, Y * -XA19 Shorted shaft (Double shaft) V V V V W, Y * -XA2 Reverse shaft, Shorted shaft V V V V S, W * -XA24 Double key V V V V Combination Chart of Made to Order Chart 2. Combination between -XAl and -XCl * Corresponding shafts type available for combination Description Applicable shaft type Applicable Combination S W Y size -XA1, 2, 13 to 19 -XA2, 24 -XC7 Reversed shaft V V 5, 63, -XC8 to -XC11 Change of rotation range V V V 8, 1 V -XC3 Changed to fluorine grease V V V 3 to 1 V V -XC31 to -XC36 Change of rotation range and shaft rotation direction V V V V -XC37 to -XC46 Change of rotation range and angle adjusting direction V V V 5, 63, V -XC47 to -XC58 Change of rotation range and angle adjusting direction 8, 1 V V V (Angle adjusting screw is equipped on the left.) V -XC59 to -XC61 Change of port location V V V 3 to 1 V V -XC63 One side air-hydro, One side air V V V 5, 63, V V -XC64 One side air-hydro, One side air V V V 8, 1 V V * -XC8 to -XC11 and -XC31 to -XC36 do not include the angle adjustable type. * -XC37 to -XC46 and -XC47 to -XC58 are only the angle adjustable type. * -XC59 to -XC61 do not include the model with solenoid valve. * -XC63 and -XC64 are only the air-hydro type. X X Chart 3. Combination between -Xl and -XAl Applicable shaft type Applicable Combination Description S W X size -XA1, 2, 13 to 19 -XA2, 24 -X6 Stainless steel shaft/bolt, etc. V V V V V 3 to 1 -X7 Heat resistant (1 C) V V V V V -X1 Both sides angle adjustable V V V V V 5 to 1 -X11 One side angle adjustable, One side with cushion V V V V V -X16 Fluororubber seal V V V 3 to 1 V V * -X1 and -X11 are only the angle adjustable type. * -X7 and -X16 do not include the model with solenoid valve. 213

31 Series Shaft Pattern Sequencing1 Applicable shaft type: S, W, Y Additional Reminders 1. Enter the dimensions within a range that allows for additional machining. 2. Unless indicated otherwise, the dimensional tolerance conforms to the general tolerance. SMC will make appropriate arrangements. 3. The length of the unthreaded portion is 2 to 3 pitches. 4. Unless specified otherwise, the thread pitch is based on coarse metric threads. P = Thread pitch M4 x.7, M5 x.8, M6 x 1, M8 x 1.25, M1 x Enter the desired figures in the portion of the diagram. 6. Chamfer face of the parts machining additionally is C.5. : A2 Machine female threads into the short shaft. Note) Except flange type The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M4: L2 = 8 Applicable shaft types: S, W, Y -XA1 to -XA17 : A13 Shaft through-hole Note) Except flange type : A14 Note) Except flange type Minimum machining diameter for d1 is.1. Applicable shaft types: S, W, Y d1 = ø : A1 The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M4: L1 = 8 Applicable shaft types: S, W, Y L1 + (3 x P) Q1 3 M3 5 M4, M5, M6 63 M4, M5, M6 8 M4, M5, M6, M8 1 M5, M6, M8, M1 Machine female threads into the long shaft. Note) Except flange type L1 = A special end is machined onto the long shaft, and a through-hole is drilled into it. Female threads are machined into the throughhole, whose diameter is equivalent to the pilot hole diameter. The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M5: L1 = 1 Applicable shaft types: S, W, Y Q1 = M Q1 = M L2 + (3 x P) L2 = Q2 = M Q2 3 M3, M4 5 M4, M5, M6 63 M4, M5, M6 8 M4, M5, M6, M8 1 M5, M6, M8, M1 d1 3 ø2.5 5 ø4 to ø 7 63 ø4 to ø 8 8 ø6.8 to ø11 1 ø6.8 to ø13 L1 = Thread M3 x.5 ø2.5 M5 x.8 ø4 ø4 M6 x 1 ø5 ø5 M8 x 1.25 ø6.8 ø 6.8 ø 6.8 M1 x 1.5 ø 8.5 ø 8.5 M12 x 1.75 ø1.3 ø1.3 Rc1/8 ø 8 ø 8 Rc1/4 ø11 : A15 Note) Except flange type A special end is machined onto the short shaft, and a through-hole is drilled into it. Female threads are machined into the through-hole, whose diameter is equivalent to the pilot hole diameter. The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M5: L2 = 1 Applicable shaft types: S, W, Y : A16 Note) Except flange type A special end is machined onto both the long and short shafts, and a throughhole is drilled into both shafts. Female threads are machined into the through-holes, whose diameter is equivalent to the diameter of the pilot holes. The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M5: L1 = 1 Applicable shaft types: S, W, Y Equal dimensions are indicated by the same marker. Q1 = M : A17 Note) Except flange type Shorten the long shaft. Applicable shaft types: S, W, Y L1 L1 = X = L2 = Q2 = M Thread M3 x.5 ø2.5 M5 x.8 ø4 ø4 M6 x 1 ø5 ø5 M8 x 1.25 ø6.8 ø 6.8 ø 6.8 M1 x 1.5 ø 8.5 ø 8.5 M12 x 1.75 ø1.3 ø1.3 Rc1/8 ø 8 ø 8 Rc1/4 ø Q1 Thread M3 x.5 ø2.5 M5 x.8 ø4 ø4 M6 x 1 ø5 ø5 M8 x 1.25 ø6.8 ø 6.8 ø 6.8 M1 x 1.5 ø 8.5 ø 8.5 M12 x 1.75 ø1.3 ø1.3 Rc1/8 ø 8 ø 8 Rc1/4 ø11 X 3 15 to to to to to 6

32 Simple Specials Series Shaft Pattern Sequencing1 Applicable shaft type: S, W, Y -XA18 to -XA24 : A18 Note) Except flange type Shorten the short shaft. Applicable shaft types: W, Y Y1 Y2 W Y 3 3 to 8 15 to to to to to to to to to 6 Shaft type : A24 Y1 = Double key Keys and keyways are machined additionally at 18 from the standard position. Applicable shaft types: S, W, Y Equal dimensions are indicated by the same marker. LL LL Y2 = : A19 Note) Except flange type Both the long shaft and short shaft are shortened. Applicable shaft types: W, Y X Y1 Y2 W Y W Y 3 15 to 25 3 to 8 15 to to 36 1 to to to 41 1 to to to 5 1 to to to 6 1 to to 6 Shaft type X = Y1 = Y2 = X = : A2 Note) Except flange type Reverse the assembly of the shaft. (Thus shortening the long end and the short end of the shaft.) (If shortening the shaft is not required, indicate * for dimension X and Y.) Applicable shaft types: S, W X Y W S W 5 2 to to to to to 2 25 to to to 6 Shaft type Y = Y = X = X X Key dimensions Key dimensions LL 3 3 x 3 x x 5 x x 6 x x 6 x x 7 x

33 Series Shaft Pattern Sequencing2 Applicable shaft type: X, Z, T, J, K -XA33 to -XA59 How to Order C D RA1 B J 5 9 Z M9BW X A33 A34 C8 C3 Magnet Nil None D Built-in magnet Solenoid valve Nil None V* With solenoid valve * Except size 3, air-hydro type Mounting B Basic type L Foot type Shaft type X Single shaft with four chamfers Z Double shaft with four chamfers T Single round shaft J Double shaft (round shaft, with four chamfers) K Double round shaft Variation Nil Without angle adjustment U* Angle adjustable type H* Air-hydro type * Except size Port type M thread M5 Nil Rc TF G 1/8 1/8 1/4 3/8 TN NPT TT NPTF Rotating angle * 1 19* 19 * Except size 3 Auto switch Nil Cushion Nil Without air cushion C* With air cushion * Except angle adjustable type, air-hydro type Number of auto switches Nil 2 pcs. S 1 pc. Without auto switch (Built-in magnet) * For applicable auto switch model, refer to page 188. * Auto switches are shipped together, (but not assembled). Model with solenoid valve * Refer to page 22 for model number with solenoid valve. for simple specials, made-to-order products * Combination of XA is possible for up to 2 types. Combination 3 types Combination of applicable chart A33 A34 C3 Chart 4, 5 A35 C 9 C59 Chart 5, 7 Combination is available only when all the conditions are fulfilled in the combination chart. Combination 4 types Combination of applicable chart A33 A34 C3 C59 Chart 4, 5, 7 A45 A46 C3 C61 Chart 4, 5, 7 Combination is available only when all the conditions are fulfilled in the combination chart. * Combination of simple special and made-to-order is possible for up to 4 types. * Above is the typical example of combination. 216

34 Simple Specials Series Shaft Pattern Sequencing2 Applicable shaft type: X, Z, T, J, K Combination Chart of Simple Specials for Shaft Shape Chart 4. Combination between -XAl and -XAl -XA33 to -XA59 Description Axial direction Applicable shaft type Combination Top Bottom X Z T J K * Corresponding shafts type available for combination -XA33 Shaft-end female thread V V V V -XA33 -XA34 Shaft-end female thread V V V V T, J, K * -XA34 -XA35 Shaft-end female thread V V V -XA35 -XA36 Shaft-end female thread V V V X, Z * -XA36 -XA37 Stepped round shaft V V V V T, J, K * -XA37 -XA38 Stepped round shaft V V K * K * -XA4 Shaft through-hole V V V V -XA41 Shaft through-hole V V V V V -XA43 Shaft through-hole + Double shaft-end female thread V V V V -XA44 Shaft through-hole + Double shaft-end female thread V V V V V -XA38 -XA45 Middle-cut chamfer V V V V T, J, K * K * -XA4 -XA41 -XA45 -XA46 Middle-cut chamfer V V K * K * K * -XA46 -XA51 Change of long shaft length (Without keyway) V V V V T, J, K * K * T, K * J * K * -XA52 Change of short shaft length (Without keyway) V V K * K * K * -XA53 Change of double shaft length (Both without keyway) V V V K * -XA54 Change of long shaft length (With four chamfers) V V V X, Z * X, Z * -XA55 Change of short shaft length (With four chamfers) V V V J * Z * J * J, Z * J * -XA56 Change of double shaft length (Both with four chamfers) V V V Z * -XA57 Change of double shaft length (Without keyway, With hour chamfers) V V V J * -XA58 Reversed shaft, Change of shaft length (With four chamfers, Without keyway) V V V V T * J * -XA59 Reversed shaft, Change of shaft length (With four chamfers) V V X * Combination Chart of Made to Order X X Chart 5. Combination between -XAl and -XCl Description Applicable shaft type Applicable Combination X Z T J K size -XA33 to 38, 4 to 46, 51 to 59 -XC7 Reversed shaft V V V 5, 63, -XC8 to -XC11 Change of rotation range 8, 1 -XC3 Changed to fluorine grease V V V V V 3 to 1 V -XC31 to -XC36 Change of rotation range and shaft rotation direction -XC37 to -XC46 Change of rotation range and angle adjusting direction 5, 63, -XC47 to -XC58 Change of rotation range and angle adjusting direction 8, 1 (Angle adjusting screw is equipped on the left.) -XC59 to -XC61 Change of port location V V V V V 3 to 1 V -XC63 One side air-hydro, One side air V V V V V 5, 63, V -XC64 One side air-hydro, One side air V V V V V 8, 1 V * -XC8 to -XC11 and -XC31 to -XC36 do not include the angle adjustable type. * -XC37 to -XC46 and -XC47 to -XC58 are only the angle adjustable type. * -XC59 to -XC61 do not include the model with solenoid valve. * -XC63 and -XC64 are only the air-hydro type. Chart 6. Combination between -Xl and -XAl Applicable shaft type Applicable Combination Description X Z T J K size -XA33 to 38, 4 to 46, 51 to 59 -X6 Stainless steel shaft/bolt, etc. V V V V V V 3 to 1 -X7 Heat resistant (1 C) V V V V V V -X1 Both sides angle adjustable V V V V V V 5 to 1 -X11 One side angle adjustable, One side with cushion V V V V V V -X16 Fluororubber seal V V V V V 3 to 1 V * -X1 and -X11 are only the angle adjustable type. * -X7 and -X16 do not include the model with solenoid valve. 217

35 Series Shaft Pattern Sequencing2 Applicable shaft type: X, Z, T, J, K Additional Reminders 1. Enter the dimensions within a range that allows for additional machining. 2. Unless indicated otherwise, the dimensional tolerance conforms to the general tolerance. SMC will make appropriate arrangements. 3. The length of the unthreaded portion is 2 to 3 pitches. 4. Unless specified otherwise, the thread pitch is based on coarse metric threads. P = Thread pitch M4 x.7, M5 x.8 M6 x 1, M8 x 1.25, M1 x Enter the desired figures in the portion of the diagram. 6. Chamfer face of the parts machining additionally is C.5. : A35 Machine female threads into the long shaft. Note) Except flange type The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M4: L1 = 8 Applicable shaft types: X, Z L1 + (3 x P) L1 = Q1 = M : A33 The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M4: L1 = 8 Applicable shaft types: J, K, T L1 + (3 x P) Q1 3 M3 5 M4, M5, M6, M8 63 M4, M5, M6, M8, M1 8 M4, M5, M6, M8, M1, M12 1 M5, M6, M8, M1, M12 : A36 Machine female threads into the short shaft. Note) Except flange type The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M4: L2 = 8 Applicable shaft types: X, Z Q2 = M L1 = Machine female threads into the long shaft. Note) Except flange type L2 = Q2 = M Q1 = M L2 = : A34 -XA33 to -XA41 Machine female threads into the short shaft. Note) Except flange type The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M4: L2 = 8 Applicable shaft types: J, K, T L2 + (3 x P) L2 = Q2 3 M3 5 M4, M5, M6, M8 63 M4, M5, M6, M8, M1 8 M4, M5, M6, M8, M1, M12 1 M5, M6, M8, M1, M12 : A37 Note) Except flange type The long shaft can be further shortened by machining it into a stepped round shaft. The minimum unit of the dimensions within a range that allows for machining is.1. (If shortening the shaft is not required, indicate * for dimension X.) (If not specifying dimension C1, indicate * instead.) C1 = C Q2 = M L2 + (3 x P) L2 = Q2 = M Applicable shaft types: J, K, T Equal dimensions are indicated by the same marker. D1 = ø Z axis X axis C1 Q1 3 M3 5 M4, M5, M6, M8 63 M4, M5, M6, M8, M1 8 M4, M5, M6, M8, M1, M12 1 M5, M6, M8, M1, M12 Q2 3 M3 5 M4, M5, M6, M8 63 M4, M5, M6, M8, M1 8 M4, M5, M6, M8, M1, M12 1 M5, M6, M8, M1, M12 L1 = X = X L1max D1 3 3 to 25 X-2 ø5 to ø to 36 X-2.5 ø5 to ø to 41 X-2.5 ø5 to ø to 5 X-3 ø8 to ø to 6 X-4 ø8 to ø24.9 : A38 Note) Except flange type The short shaft can be further shortened by machining Minimum machining diameter for d1 is.1. it into a stepped round shaft. Applicable shaft types: K, T The minimum unit of the dimensions within a range that allows for machining is.1. (If shortening the shaft is not required, indicate * for dimension Y.) (If not specifying dimension C2, indicate * instead.) Applicable shaft type: K Equal dimensions are indicated by the same marker. d1 = ø d1 = ø : A4 Shaft through-hole Note) Except flange type : A41 Shaft through-hole Note) Except flange type Minimum machining diameter for d1 is.1. Applicable shaft types: J, X, Z d1 = ø d1 = ø C2 Y = K axis T axis J axis X axis D2 = ø L2 = Y L2max D2 3 3 to 25 Y-2 ø5 to ø to 36 Y ø5 to ø to 41 Y ø5 to ø to 5 Y ø8 to ø to 6 Y ø8 to ø C2 = C d1 3 ø2.5 5 ø4 to ø ø4 to ø 8 8 ø6.8 to ø11 1 ø6.8 to ø13 d1 3 ø2.5 5 ø4 to ø ø4 to ø 8 8 ø6.8 to ø11 1 ø6.8 to ø13

36 Simple Specials Series Shaft Pattern Sequencing2 Applicable shaft type: X, Z, T, J, K : A43 Applicable shaft types: K, T Equal dimensions are indicated by the same marker. Q1 = M Shaft through-hole and female thread Note) Except flange type L1 = : A46 Note) Except flange type : A44 Note) Except flange type Shaft through-hole and female thread machining Applicable shaft types: J, X, Z Equal dimensions are indicated by the same marker. Q1 = M Q1 = M Q1 Q1 Q1 Q1 K axis T axis J axis X axis Thread Thread M3 x.5 ø2.5 M3 x.5 ø2.5 M5 x.8 ø4 ø4 M5 x.8 ø4 ø4 M6 x 1 ø5 ø5 M6 x 1 ø5 ø5 M8 x 1.25 ø6.8 ø 6.8 ø 6.8 M8 x 1.25 ø6.8 ø 6.8 ø 6.8 M1 x 1.5 ø 8.5 ø 8.5 M1 x 1.5 ø 8.5 ø 8.5 M12 x 1.75 ø1.3 ø1.3 M12 x 1.75 ø1.3 ø1.3 Rc1/8 ø 8 ø 8 Rc1/8 ø 8 ø 8 Rc1/4 ø11 Rc1/4 ø11 L1 Q1 = M : A51 Note) Except flange type The short shaft can be further shortened by machining Shorten the long shaft. a middle-cut chamfer into it. Applicable shaft types: J, K, T The minimum unit of the dimensions within a range that allows for machining is.1. (The position is that of the standard flat at the keyway portion.) (If shortening the shaft is not required, indicate * for dimension Y.) Applicable shaft type: K L1 L1 = X = L1 L1 = X = L1 = : A45 Note) Except flange type The long shaft can be further shortened by machining a middle-cut chamfer into it. The minimum unit of the dimensions within a range that allows for machining is.1. (The position is that of the standard flat at the keyway portion.) (If shortening the shaft is not required, indicate * for dimension X.) Applicable shaft types: J, K, T X W1 L1max L3max to 25 1 to 2 X-2 L to 36 1 to 5.5 X-2.5 L to 41 1 to 6.5 X-2.5 L to 5 1 to 8 X-3 L to to 1.5 X-4 L1-4 : A52 Note) Except flange type Shorten the short shaft. Applicable shaft type: K -XA43 to -XA55 Y = L1 X = W1 = L3 = W2 = L4 = L2 = Y W2 L2max L4max to 25 1 to 2 Y-2 L to 36 1 to 5.5 Y L to 41 1 to 6.5 Y L to 5 1 to 8 Y L to to 1.5 Y L2-4 X 3 3 to to to to to 6 Y 3 3 to to to to to 6 : A53 Note) Except flange type Both the long shaft and short shaft are shortened. Applicable shaft type: K : A54 Note) Except flange type Shorten the long shaft. Applicable shaft types: X, Z : A55 Note) Except flange type Shorten the short shaft. Applicable shaft types: J, Z Y = Y = X = X = L1 = X = X X Y = X = X Y 3 3 to 25 3 to to 36 1 to to 41 1 to to 5 1 to to 6 1 to 6 Y = X 3 3 to to to to to 44 Y 3 3 to to to to to 3 219

37 Series Shaft Pattern Sequencing2 Applicable shaft type: X, Z, T, J, K -XA56 to -XA59 : A56 Note) Except flange type Both the long shaft and short shaft are shortened. Applicable shaft type: Z X = : A57 Note) Except flange type Both the long shaft and short shaft are shortened. Applicable shaft type: J X = : A58 Note) Except flange type The rotation axis is reversed, and then shorten the long and short shafts. Applicable shaft types: J, T X Y 3 3 to 13 3 to to 27 1 to to 29 1 to to 38 1 to to 44 1 to 3 Y = Y = X Y 3 3 to 25 3 to to 36 1 to to 41 1 to to 5 1 to to 6 1 to 3 Y = Y 5 1 to to to to 6 : A59 Note) Except flange type The rotation axis is reversed, and then shorten the long and short shafts. Applicable shaft type: X Y = X = Y = Y 5 1 to to to to 44 22

38 Series Made to Order Please contact SMC for detailed dimensions, specifications and lead times. C D RA1 B S 5 9 Z M9BW X C8 C3 C59 Magnet Nil None D Built-in magnet Solenoid valve Nil None V* With solenoid valve * Except size 3, air-hydro type Mounting B Basic type L Foot type F* Flange type * Except size 3, with solenoid valve type. Shaft type S Single shaft W Double shaft X Single shaft with four chamfers Y Double shaft with key Z Double shaft with four chamfers T Single round shaft J Double shaft (round shaft, with four chamfers) K Double round shaft Variation Nil Without angle adjustment U* Angle adjustable type H* Air-hydro type * Except size Combination Chart of Made to Order Chart 7. Combination between -XCl and -XCl How to Order Rotating angle * 1 19* 19 * Except size 3 Port type Model with solenoid valve * Refer to page 22 for model number with solenoid valve. Cushion Nil Without air cushion C* With air cushion * Except angle adjustable type, air-hydro type Auto switch Nil M thread M5 Nil Rc TF G 1/8 1/8 1/4 3/8 TN NPT TT NPTF Number of auto switches Nil 2 pcs. S 1 pc. Without auto switch (Built-in magnet) * For applicable auto switch model, refer to page 188. * Auto switches are shipped together, (but not assembled). for simple specials, made-to-order products * Combination of XA is possible for up to 2 types. Combination 3 types Combination of applicable chart C 7 C3 C59 Chart 7 Combination is available only when all the conditions are fulfilled in the combination chart. * Combination of simple special and made-to-order is possible for up to 3 types. * Above is the typical example of combination. Description Applicable shaft type Applicable S W X Y Z T J K size Combination -XC7 Reversed shaft V V V V V 5, 63, -XC7 -XC8 to -XC11 Change of rotation range V V V 8, 1 -XC8 to -XC11 -XC3 Changed to fluorine grease V V V V V V V V 3 to 1 S,W,X,T,J * S,W,Y * -XC3 -XC31 to -XC36 Change of rotation range and shaft rotation direction V V V S,W,Y * -XC31 to -XC36 -XC37 to -XC46 Change of rotation range and angle adjusting direction V V V 5, 63, S,W,Y * -XC37 to -XC46 Change of rotation range and angle adjusting direction 8, 1 -XC47 to -XC58 V V V (Angle adjusting screw is equipped on the left.) -XC47 to -XC58 -XC59 to -XC61 Change of port location V V V V V V V V 3 to 1 S,W,Y * V S,W,Y * S,W,Y * S,W,Y * S,W,Y * -XC59 to -XC61 -XC63 One side air-hydro, One side air V V V V V V V V 5, 63, V V V V -XC64 One side air-hydro, One side air V V V V V V V V 8, 1 V V V V * -XC8 to -XC11 and -XC31 to -XC36 do not include the angle adjustable type. * -XC37 to -XC46 and -XC47 to -XC58 are only the angle adjustable type. * -XC59 to -XC61 do not include the model with solenoid valve. * -XC63 and -XC64 are only the air-hydro type. Chart 8. Combination between -Xl, -XCl Description Applicable shaft type Applicable Combination S W X Y Z T J K size -XC7 -XC8 to -XC11 -XC3 -XC31 to -XC36 -XC37 to -XC58 -XC59 to -XC61 -XC63 -XC64 -X6 Stainless steel shaft/bolt, etc. V V V V V V V V 3 to 1 V V V V V V V -X7 Heat resistant (1 C) V V V V V V V V V V V V V -X1 Both sides angle adjustable V V V V V V V V 5 to 1 V V V -X11 One side angle adjustable, One side with cushion V V V V V V V V V V -X16 Fluororubber seal V V V V V V V V 3 to 1 V V V V V V * -X1 and -X11 are only the angle adjustable type. * -X7 and -X16 do not include the model with solenoid valve. 221 X X

39 +4 Series 1 Reversed Shaft -XC7 2 Change of Rotation Range -XC8 to -XC11 ClRA1 ClRA1llU Standard model no. -XC7 ClRA1 Standard model no. -XC8 Reversed shaft Specifications (-XC7) Applicable size 5, 63, 8, 1 Applicable shaft type S, W, X, T, J Specifications Applicable size 5, 63, 8, 1 Applicable shaft type S, W, Y Change of rotation range (-XC8 to -XC11) : C7 : C8 Change of rotation range : C9 Change of rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. : C1 Change of rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. : C11 Change of rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Rotation range of keyway Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. 3 Changed to Fluorine Grease -XC3 ClRA1 ClRA1llU Lubricant oil in the seal parts and inner wall of the cylinder is changed to fluorine grease. (Not the low-speed specification) Standard model no. Fluorine grease (-XC3) -XC3 Specifications Applicable size 3, 5, 63, 8, 1 Applicable shaft type S, W, X, Y, Z, T, J, K * Refer to standard type and angle adjustable type for other specifications. 222

40 Made to Order Series 4 Change of Rotation Range and Shaft Rotation Direction -XC31 to -XC36 ClRA1 Specifications Applicable size 5, 63, 8, 1 Applicable shaft type S, W, Y : C31 The rotation range is changed and the rotating direction is reversed. +4 Standard model no. : C32 -XC31 The rotation range is changed and the rotating direction is reversed. +4 Change of rotation range and shaft rotation direction (-XC31 to -XC36) : C33 The rotation range is changed and the rotating direction is reversed. +4 X X Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. : C34 : C35 : C36 The rotation range is changed and the rotating direction is reversed. The rotation range is changed and the rotating direction is reversed. The rotation range is changed and the rotating direction is reversed. Rotation range of keyway Rotation range of keyway Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. 223

41 Series 5 Change of Rotation Range and Angle Adjusting Direction -XC37 to -XC42 ClRA1llU Standard model no. -XC37 Specifications Applicable size 5, 63, 8, 1 Applicable shaft type S, W, Y Change of rotation range and angle adjusting direction (-XC37 to -XC42) : C37 The rotation range and the angle adjusting direction of the angle adjustable type are changed. Angle adjusting screw : C38 The rotation range and the angle adjusting direction of the angle adjustable type are changed. Angle adjusting screw : C39 The rotation range and the angle adjusting direction of the angle adjustable type are changed. Angle adjusting screw The rotation range under the adjustment of an angle at 6 is indicated below. : C4 Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. The rotation range and the angle adjusting direction of the angle adjustable type are changed. Angle adjusting screw The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range : C41 Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. The rotation range and the angle adjusting direction of the angle adjustable type are changed. Angle adjusting screw The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range : C42 Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. The rotation range and the angle adjusting direction of the angle adjustable type are changed. The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range Angle adjusting screw Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. 224

42 Made to Order Series 6 Change of Rotation Range and Angle Adjusting Direction -XC43 to -XC46 ClRA1llU Standard model no. -XC43 Specifications Applicable size 5, 63, 8, 1 Applicable shaft type S, W, Y : C43 The rotation range and the angle adjusting direction of the angle adjustable type are changed. Angle adjusting screw The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. : C46 The rotation range and the angle adjusting direction of the angle adjustable type are changed. : C44 The rotation range and the angle adjusting direction of the angle adjustable type are changed. Angle adjusting screw The rotation range under the adjustment of an angle at 12 is indicated below. Rotation range Rotation range of keyway 18 Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Change of rotation range and angle adjusting direction (-XC43 to -XC46) : C45 The rotation range and the angle adjusting direction of the angle adjustable type are changed. The rotation range under the adjustment of an angle at 12 is indicated below. Rotation range Rotation range of keyway 18 Angle adjusting screw Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. X X Rotation range of keyway 18 Angle adjusting screw The rotation range under the adjustment of an angle at 12 is indicated below. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. 225

43 Series 7 Change of Rotation Range and Angle Adjusting Direction (Angle adjusting screw is equipped on the left.) -XC47 to -XC52 ClRA1llU Standard model no. -XC47 Specifications Applicable size 5, 63, 8, 1 Applicable shaft type S, W, Y Change of rotation range and angle adjusting direction (Angle adjusting screw is equipped on the left.) (-XC47 to -XC52) : C47 For the angle adjusting type, angle adjusting screws are mounted to the left cover. Angle adjusting screw : C48 For the angle adjusting type, angle adjusting screws are mounted to the left cover. Angle adjusting screw : C49 For the angle adjusting type, angle adjusting screws are mounted to the left cover. Angle adjusting screw The rotation range under the adjustment of an angle at 6 is indicated below. : C5 Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. For the angle adjusting type, angle adjusting screws are mounted to the left cover. Angle adjusting screw The rotation range under the adjustment of an angle at 6 is indicated below. : C51 Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. For the angle adjusting type, angle adjusting screws are mounted to the left cover. The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range : C52 Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. For the angle adjusting type, angle adjusting screws are mounted to the left cover. The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range Angle adjusting screw Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range Angle adjusting screw Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. 226

44 Made to Order Series 8 Change of Rotation Range and Angle Adjusting Direction (Angle adjusting screw is equipped on the left.) -XC53 to -XC58 ClRA1llU Standard model no. -XC53 Specifications Applicable size 5, 63, 8, 1 Applicable shaft type S, W, Y : C53 For the angle adjusting type, angle adjusting screws are mounted to the left cover. Angle adjusting screw The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. : C54 For the angle adjusting type, angle adjusting screws are mounted to the left cover. Angle adjusting screw The rotation range under the adjustment of an angle at 6 is indicated below. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Change of rotation range and angle adjusting direction (Angle adjusting screw is equipped on the left.) (-XC53 to -XC58) : C55 For the angle adjusting type, angle adjusting screws are mounted to the left cover. Angle adjusting screw The rotation range under the adjustment of an angle at 12 is indicated below. Rotation range Rotation range of keyway 18 Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. X X : C56 : C57 : C58 For the angle adjusting type, angle adjusting screws are mounted to the left cover. Rotation range of keyway 18 For the angle adjusting type, angle adjusting screws are mounted to the left cover. Angle adjusting screw Rotation range of keyway 18 For the angle adjusting type, angle adjusting screws are mounted to the left cover. Angle adjusting screw Rotation range of keyway 18 Angle adjusting screw The rotation range under the adjustment of an angle at 12 is indicated below. The rotation range under the adjustment of an angle at 12 is indicated below. The rotation range under the adjustment of an angle at 12 is indicated below. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. Rotation range Note) If it is pressurized from the port indicated with the arrow, the shaft rotates in the clockwise direction. 227

45 Series 9 Change of Port Location (Mounting location of the cover is changed.) -XC59 to -XC61 ClRA1 ClRA1llU Specifications Applicable size 3, 5, 63, 8, 1 Applicable shaft type S, W, X, Y Z, T, J, K Standard model no. -XC59 Change of port location (Mounting location of the cover is changed.) (-XC59 to -XC61) : C59 Direction of the port is changed. (Upward) : C6 Direction of the port is changed. (Downward) : C61 Direction of the port is changed. (Backward) Port Port Port Port Port Port Port Port Port 1 One Side Air-hydro, One Side Air -XC63, -XC64 ClRA1 Standard model no. -XC63 Specifications Applicable size 5, 63, 8, 1 Applicable shaft type S, W, X, Y Z, T, J, K * Except angle adjustable type and air cushion equipped type : C63 One side air, one side air-hydro specification (Left side air, Right side hydro) Bleeder valve : C64 One side air-hydro, One side air -XC63: Left side air Right side air-hydro -XC64: Left side air-hydro Right side air One side air, one side air-hydro specification (Left side hydro, Right side air) Bleeder valve Air pressure port Hydro pressure port Hydro pressure port Air pressure port The figure shows the pressurized situation to the hydro pressure port. The figure shows the pressurized situation to the air pressure port. 228

46 Made to Order Series 11 Stainless Steel Shaft/Bolt/Parallel Key -X6 ClRA1 Standard model no. -X6 Stainless steel for main part For applications in areas that pose a risk of rust or corrosion, a portion of the materials used in the standard parts has been changed to stainless steel. Specifications Type Pneumatic, Air-hydro 3, 5, 63, 8, 1 Rotating angle 9, 18 ( 3 to 1) 1, 19 ( 5 to 1) Mounting Flange, Foot Single shaft (S), Double shaft (W), Single shaft with four chamfers (X), Double Shaft type shaft with key (Y), Double shaft with four chamfers (Z), Single round shaft (T), Double shaft (round shaft, with four chamfers) (J), Double round shaft (K) Stainless steel part Shaft, Bolt, Screw, Parallel key Cushion Not attached, Air cushion (Except air-hydro type) Auto switch Mountable Refer to page 188 for other specifications. Except angle adjustable type Only single shaft (S) and double shaft (W) types are applicable to flange type. 13 Both Sides Angle Adjustable -X1 ClRA1llU Specifications Standard model no. -X1 Both sides angle adjustable Type Pneumatic 5, 63, 8, 1 Rotating angle 9, 18, 1, 19 Mounting Shaft type Cushion Angle adjustment range Refer to page 198 for other specifications. Flange, Foot Single shaft (S), Double shaft (W), Single shaft with four chamfers (X), Double shaft with key (Y), Double shaft with four chamfers (Z), Single round shaft (T), Double shaft (round shaft, with four chamfers) (J), Double round shaft (K) None Max. 9 (One side) X X 12 Heat Resistant -X7 Standard model no. -X7 Heat resistant Adjusting direction Adjusting direction A : When angle adjusting screw on A side is screwed into the right direction. Adjusting direction B : When angle adjusting screw on B side is screwed into the right direction. Angle adjusting screw "B" Rotation at 9 Angle adjusting screw "A" In this rotary actuator, the material of the seals has been changed to the heat resistant type (to withstand up to 1 C), for applications in environments that exceed the standard specification temperatures of to 6 C. Specifications Type Pneumatic 3, 5, 63, 8, 1 Rotating angle 9, 18 ( 3 to 1) 1, 19 ( 5 to 1) Ambient and fluid temperature to 1 C Mounting Flange, Foot Single shaft (S), Double shaft (W), Single shaft with four chamfers (X), Double Shaft type shaft with key (Y), Double shaft with four chamfers (Z), Single round shaft (T), Double shaft (round shaft, with four chamfers) (J), Double round shaft (K) Angle adjusting screw "B" Adjusting direction with Rotation at 18 angle adjusting screw A Adjusting direction with angle adjusting screw B Angle adjusting screw "A" Seal material FKM 3: None Cushion 5 to 1: Not attached, Air cushion Auto switch Not mountable Refer to page 188 for other specifications. Except with solenoid valve type. Adjusting direction with angle adjusting screw A Rotation range of keyway 18 Adjusting direction with angle adjusting screw B 229

47 Series 14 One Side Angle Adjustable, One Side with Cushion -X11 15 Fluororubber Seal -X16 ClRA1llU Standard model no. -X11 CDRA1 Standard model no. -X16 One side angle adjustable One side with cushion Fluororubber seal Seal is now changed to fluororubber. Specifications Type Pneumatic 5, 63, 8, 1 Rotating angle 9, 18, 1, 19 Mounting Shaft type Cushion Flange, Foot Single shaft (S), Double shaft (W), Single shaft with four chamfers (X), Double shaft with key (Y), Double shaft with four chamfers (Z), Single round shaft (T), Double shaft (round shaft, with four chamfers) (J), Double round shaft (K) With cushion on one side Angle adjustment range Max. 9 Refer to page 198 for other specifications. Specifications Type Pneumatic 3, 5, 63, 8, 1 Rotating angle 9, 18 ( 3 to 1) 1, 19 ( 5 to 1) Ambient and fluid temperature to 6 C (No freezing) Mounting Flange, Foot Single shaft (S), Double shaft (W), Single shaft with four chamfers (X), Double Shaft type shaft with key (Y), Double shaft with four chamfers (Z), Single round shaft (T), Double shaft (round shaft, with four chamfers) (J), Double round shaft (K) Seal material FKM Cushion Not attached, Air cushion Auto switch Mountable Refer to page 188 for other specifications. Except with solenoid valve type. For built-in magnet type only. Rotation at 9 Angle adjusting screw Cushion valve Operating range of cushion Rotation at 18 Angle adjusting screw Operating range of cushion Cushion valve Rotation range of keyway 18 Refer to page 2 for dimensions. 23