Vane Type Rotary Actuator

Size: px
Start display at page:

Download "Vane Type Rotary Actuator"

Transcription

1 Vane Type Rotary Actuator 5, 63, 8, 1 New Compact auto switches are mountable! (D-M9 ) Compact auto switch D-M9 Stainless steel specification for main parts : 5, 63, 8, 1 Special screw Hexagon socket head cap screw Direct mounting Parallel key Vane shaft Two different port locations (side and axial) are available. Side ported plate (Provided by customer) Foot mounting Axial ported Series CAT.ES2-247A

2 Vane Type Rotary Actuator Series Basic type Series With solenoid valve Series CVRB1 Series Variations Fluid Air Vane type S: Single vane D: Double vane S D S D S D S D Port location Side ported (Nil) Axial ported (E) Side ported Axial ported Side ported Axial ported Side ported Axial ported Side ported Axial ported Side ported Axial ported Side ported Axial ported Side ported Axial ported Side ported Axial ported 9 18 Standard Rotating angle Semi-standard Shaft type Double shaft W Cushion Rubber bumper Basic type With auto switch Variations With One-touch fi ttings Clean series 1- Copper-free and fl uorine-free 2- With solenoid valve CVRB1 Option With foot bracket L Material Shaft type Single shaft type Double shaft type Stainless steel specification for main parts Double shaft (Long shaft with four chamfers) J Double shaft with four chamfers Z Double shaft key Y Double round shaft K Single shaft key S Single round shaft T Single shaft with four chamfers X 1 Pattern Shaft pattern Rotation pattern

3 CONTENTS Vane Type Rotary Actuator Series Vane Type Rotary Actuator Series How to Order Page 3 Specifications Page 4 Construction Page 9 Dimensions Page 1 Rotary Actuator with Solenoid Valve Series CVRB1 How to Order Page 14 Specifications Page 15 Dimensions Page 15 Shaft Pattern Sequencing 1 -XA1 to -XA24 Page 17 Shaft Pattern Sequencing 2 -XA31 to -XA6 Page 2 Page 26 CVRB1 Auto Switch Auto Switch Page 28 2

4 Vane Type Rotary Actuator Series : 5, 63, 8, 1 How to Order Basic type B W 8 9 S With auto switch CDRB1 B W 8 9 S M9B L With auto switch (With auto switch unit and built-in magnet) Refer to page 28 when the auto switch unit is needed separately. W B Basic L Foot Refer to Table (1) below when foot bracket assembly is required separately. Table (1): Foot Bracket Assembly Part Number Model Assembly part no. LW5 P LW63 P LW8 P LW1 P Shaft type Double shaft (Long shaft key & Four chamfers) Standard Semistandard Rotating angle Classification Symbol Single vane Double vane S D Vane type Single vane Double vane Connecting port location Nil Side ported E Axial ported Auto switch Nil Without auto switch (Built-in magnet) Without D-M9 type auto switch M (Built-in magnet) For applicable auto switch model, refer to the table below. The operating range and hysteresis of the D-M9 are different from those of the other auto switches. For details, refer to page 28. or Port thread type Refer to pages 17 to 19, 26 and 27 for details about specifi cations. Nil Rc -XF G -XN NPT Combination with Made to Order is not available. Number of auto switches S 1 pc. Nil 2 pcs. S: A right-hand auto switch is shipped. Nil: A right-hand switch and a left-hand switch are shipped. Electrical entry/lead wire length Nil Grommet/Lead wire:.5 m M Grommet/Lead wire: 1 m L Grommet/Lead wire: 3 m CN Connector/Without lead wire C Connector/Lead wire:.5 m CL Connector/Lead wire: 3 m Connectors are available only for the R73, R8, T79. Lead wire with connector part nos. D-LC5: Lead wire.5 m D-LC3: Lead wire 3 m D-LC5: Lead wire 5 m Applicable Auto Switches/Refer to the Best Pneumatics No.4 for further information on auto switches. Type Solid state auto switch Reed auto switch Auto switch Lead wire length [m] Special Electrical Wiring Load voltage Lead wire Pre-wired Applicable model None function entry (Output) type connector load DC AC Perpendicular In-line (Nil) (M) (L) (Z) (N) 3-wire (NPN) 5 V, M9NV M9N IC circuit 3-wire (PNP) 12 V M9PV M9P Grommet 2-wire 12 V M9BV M9B Yes 3-wire (NPN) 5 V, S79 IC circuit 3-wire (PNP) 12 V S7P Oilproof Relay, 24 V T79 heavy-duty 2-wire 12 V PLC Connector T79C cord Grommet 1 V R73 Yes Connector R73C 2-wire Grommet 48 V, 1 V 1 V R8 IC circuit No Connector 24 V or less R8C Indicator light Lead wire length symbols:.5 m 3 m 5 m None 3 Nil L Z N (Example) R73C (Example) R73CL (Example) R73CZ (Example) R73CN Solid state auto switches marked with are produced upon receipt of order.

5 Vane Type Rotary Actuator Series Excellent reliability and durability. The use of bearings to support thrust and radial loads improves reliability and durability. The body of the rotary actuator can be mounted directly. Two different port locations (side and axial) are available. : 8 Symbol : 5 : 1 : 63 Specifications Vane type Single vane (S) Double vane (D) Rotating Standard 9 +4, 18 +4, angle Semi-standard 1 +4, 19 +4, Fluid Air (Non-lube) Proof pressure 1.5 MPa Ambient and fluid temperature 5 to 6 C Max. operating pressure Min. operating pressure Rotation time adjustment range 1. MPa.15 MPa.1 to 1 s/9 Allowable kinetic energy.82 J.12 J.398 J.6 J.112 J.16 J.54 J.811 J Shaft Allowable radial load 245 N 39 N 49 N 588 N 245 N 39 N 49 N 588 N load Allowable thrust load 196 N 34 N 49 N 539 N 196 N 34 N 49 N 539 N Bearing Bearing Port location Side ported or Axial ported Port Side ported 1/8 1/4 1/8 1/4 size Axial ported 1/8 1/4 1/8 1/4 Basic, Foot Volume Classification Standard Semistandard Rotating angle Single vane (S) Double vane (D) [cm 3 ] CVRB1 Auto Switch Refer to pages 28 to 3 for actuators with auto switches. Auto switch unit and switch block unit Operating range and hysteresis How to change the auto switch detecting position Auto switch mounting Auto switch adjustment Symbol (For details, refer to pages 17 to 19, 26 and 27.) Description XA1 to XA24 Shaft type pattern XC1 XC4 XC5 XC6 XC7 XC26 XC27 XC3 Addition of connection port Change of rotating angle Change of rotating angle Change of rotating angle Reversed shaft Change of rotating angle Change of rotation range and direction Fluorine grease Weight Model Main body Rotating angle Auto switch unit + 2 auto switches Single vane (S) Double vane (D) Foot bracket assembly Bracket Assembly Part No. Model Foot bracket assembly Basic type With auto switch part number LW5 CDRB1LW5 P LW63 CDRB1LW63 P LW8 CDRB1LW8 P LW1 CDRB1LW1 P Refer to page 12 for detailed dimensions. Description 2 foot brackets 8 mounting bolts 8 mounting nuts 8 washers [g] 4

6 Series Effective Output : 5 : 63 : 8 : 1 5 Effective torque [N m] Double vane Single vane Effective torque [N m] Double vane Single vane Effective torque [N m] Double vane Single vane Effective torque [N m] Double vane Single vane Operating pressure [MPa] Operating pressure [MPa] Operating pressure [MPa] Operating pressure [MPa] (Top View from Long Shaft Side) Key positions in the figures below show the intermediate rotation position when A or is pressurized. Key Position and Rotation Range Single vane type Double vane type Standard (45 ) Key rotation range Key Key (9 ) Key rotation range Key Key rotation range 27 (45 ) Key rotation range 9 Key (45 ) Semi-standard (4 ) Key rotation range Key Key Key rotation range 19 (85 ) + 4 Key Key rotation range Key rotation range 1 Key (4 ) (4 ) Direct of Body L 4 screws Reference Screw L Screw 5 48 M M M M1 5

7 Vane Type Rotary Actuator Series With One-touch Fittings Clean Series W5F Rotating angle Vane type Port location With One-touch fittings 1 BW Rotating angle Vane type Clean series, with relief port Port location With One-touch fittings facilitate the piping work and greatly reduce the installation space. Specifications Vane type Single vane Double vane 5 Operating pressure range [MPa].15 to 1. Speed regulation range [s/9 ].1 to 1 Port location Side ported or Axial ported Piping With One-touch fi ttings Basic, Foot Variations Basic type, With auto switch Applicable Tubing and Applicable tubing O.D/I.D Applicable tubing material Refer to page 13 for external dimensions. ø6/ø4 Nylon, Soft nylon, Polyurethane The double-seal construction of the actuator shaft section of these series to channel exhaust through the relief ports directly to the outside of a clean room environment allows operation of these cylinders in a class 1 clean room. Specifications Vane type Single/Double vane 5 63 Operating pressure range [MPa].15 to 1. Speed regulation range [s/9 ].1 to 1 Port location Side ported or Axial ported Piping Screw-in type Relief port size M5 x.8 Basic Variations Basic type, With auto switch Allowable kinetic energy.29 J.42 J CVRB1 M5 x.8 Relief port Auto Switch M5 x.8 Relief port The internal construction of the fi gure above shows a single vane type. 6

8 Series Stainless Steel Specification for Main Parts CDRB1 W Rotating angle Vane type Port location S Auto switch Nil Basic type D With auto switch (With switch unit) Stainless steel specification for main parts Specifications Vane type Single/Double vane Operating pressure range [MPa].15 to 1. Speed regulation range [s/9 ].1 to 1 Port location Side ported or Axial ported Piping Screw-in type Basic, Foot Variations Basic type, With auto switch Allowable kinetic energy.29 J.42 J.142 J.212 J Stainless Steel Parts Description 1 Vane shaft 2 Hexagon socket head cap screw 3 Special screw 4 Parallel key Individual part cannot be shipped. 7

9 Vane Type Rotary Actuator Series Rotary Actuator: Replaceable Shaft A shaft can be replaced with a different shaft type except for standard shaft type (W). Without auto switch J K S T X Y Z D B Shaft type Double shaft (Long shaft with four chamfers) Double round shaft Single shaft key Single round shaft Single shaft with four chamfers Double shaft key Double shaft with four chamfers D J Rotating angle Vane type Port location Key D D Symbol Description XA31 to XA6 Shaft type pattern XC1 Addition of connection port XC4 Change of rotating angle XC5 Change of rotating angle XC6 Change of rotating angle XC7 Reversed shaft XC26 Change of rotating angle XC27 Change of rotation range and direction XC3 Fluorine grease Refer to pages 2 to 27 for details. C Key J K S T X Y Z D C CVRB1 C D C D Note) Dimensions and tolerance of the shaft and keyway are the same as the standard. Key D C Auto Switch With auto switch CDRB1B J Rotating angle Vane type Port location J Z With auto switch Shaft type Double shaft (Long shaft with four chamfers) Double shaft with four chamfers J Z D C Symbol Description XA31 to XA6 Shaft type pattern XC1 Addition of connection port XC4 Change of rotating angle XC5 Change of rotating angle XC6 Change of rotating angle XC7 Reversed shaft XC26 Change of rotating angle XC27 Change of rotation range and direction XC3 Fluorine grease The above may not be selected when the product comes with an auto switch. Refer to pages 2 to 27 for details. C D Note) Dimensions and tolerance of the shaft and keyway are the same as the standard. 8

10 Series Construction Basic type (Keys in the fi gures below show the intermediate rotation position.) For 27 (Top view from long shaft side) Single vane For 18 (Top view from long shaft side) Single vane For 9 (Top view from long shaft side) Single vane For 9 (Top view from long shaft side) Double vane (Long shaft side) (Short shaft side) With auto switch (Keys in the figures below show the actuator for 18 when is pressurized.) Component Parts No. Description Material Note 1 Body (A) Aluminum alloy Painted 2 Body (B) Aluminum alloy Painted 3 Vane shaft Carbon steel 4 Stopper Aluminum alloy 5 Stopper Resin For 9 6 Stopper Resin For 18 7 Bearing Bearing steel 8 Hexagon socket head cap screw (with washer) Chrome molybdenum steel 9 Special screw Chrome molybdenum steel 1 Parallel key Carbon steel 11 O-ring NBR 12 O-ring NBR Special O-ring 13 Stopper seal NBR Special seal 14 Holding rubber NBR Individual part cannot be shipped. The material is chrome molybdenum steel for double vane type. Auto switch D-M9 Component Parts No. Description Material Note 1 Cover (A) Resin 2 Cover (B) Resin 3 Magnet lever Resin 4 Holding block Stainless steel 5 Switch block (A) Resin 6 Switch block (B) Resin 7 Magnet 8 Arm Stainless steel 9 Rubber cap NBR 1 Cross recessed round head screw Stainless steel 11 Hexagon socket head set screw Stainless steel 12 Cross recessed round head screw Chrome molybdenum steel For size 5, 63, 8 Hexagon socket head cap screw Chrome molybdenum steel For size 1 13 Cross recessed round head screw Stainless steel 14 Switch holder Stainless steel Individual part cannot be shipped. Please purchase the whole unit. (Refer to page 28.) 9

11 Vane Type Rotary Actuator Series Dimensions: 5, 63, 8, 1 Single vane type/double vane type BW - S/D <Port location: Side ported> 6 x Q V 4 x Z through Key Dimensions Key dimension L h b øe2 M2 M1 øp 4 x T 2 x R K Key length J N1 øs øf L øs H øe1 W øe1 øf G U Body (B) Body (A) G U D B C b (h9) h (h9) L Axial ported (Port location): BW - SE, BW - DE N2 2 x R If of Body (B) is machined, the port is plugged with Rc1/8. CVRB1 M3 Y Auto Switch øp 6 x Q X Y A1 A2 A1 A1 A2 B C D E1 (g6) E2 (h9) F (h9) G H J K L M1 M2 M3 N1 N2 P Q For single vane type: Above figures show actuators for 18 when is pressurized. For double vane type: Figures above show the intermediate rotation position when the A or is pressurized. In addition to Rc, G and NPT are also available for connection ports. R ( ) S T U V W X Y Z M6 x 1 depth 9 1/8 6 R M8 x 1.25 depth 1 1/8 75 R M8 x 1.25 depth 12 1/4 88 R M1 x 1.5 depth 13 1/4 18 R

12 Series Dimensions: 5, 63, 8, 1 (With auto switch) Single vane type/double vane type CDRB1BW - S/D <Port location: Side ported> Key Dimensions 6 x Q V 4 x Z through Key dimension L h b b (h9) h (h9) L W øp x T øs øf L Axial ported (Port location): CDRB1BW - SE, CDRB1BW - DE øe Key length K D M1 U G1 Body (B) If of Body (B) is machined, the port is plugged with Rc1/8. M2 N1 B 2 x R Body (A) G2 U C øs N2 2 x R M3 Y J H X Y A1 A2 D-M9 H A1 A1 A2 B C D E (g6) F (h9) G1 G2 H (R) J K L M1 M2 M3 N1 N2 P Q R R R R For single vane type: Above figures show actuators for 18 when is pressurized. For double vane type: Figures above show the intermediate rotation position when the A or is pressurized. In addition to Rc, G and NPT are also available for connection ports. 11 R ( ) S T U V W X Y Z M6 x 1 depth 9 1/8 6 R M8 x 1.25 depth 1 1/8 75 R M8 x 1.25 depth 12 1/4 88 R M1 x 1.5 depth 13 1/4 18 R

13 Vane Type Rotary Actuator Series Dimensions Option: Foot bracket LD LB1 LB2 2 x LE CVRB1 LJ2 Nut and washer Bolt and washer ølk LJ1 8 x ølh LF LM LG LJ1 LJ2 LC LD T LD LC LA2 LA1 Auto Switch Foot bracket assembly part number LA1 LA2 LB1 LB2 LC LD LE LF LG LH LJ1 LJ2 LK LM T 5 P ø P ø P ø P ø Note 1) The foot bracket (with bolt, nut, and washer) is not mounted on the actuator at the time of shipment. Note 2) The foot bracket can be mounted on the rotary actuator at 9 intervals. Note 3) Refer to the foot bracket assembly part number in the table at right when foot bracket assembly is required separately. Model Foot bracket assembly Basic type With auto switch part number LW5 CDRB1LW5 P LW63 CDRB1LW63 P LW8 CDRB1LW8 P LW1 CDRB1LW1 P

14 Series With One-touch Fittings: 5 Basic type W5F- <Port location: Side ported> With auto switch CDRB1 W5F- - <Port location: Side ported> 2 x One-touch fi tting (Fitting position: Side) 2 x One-touch fitting (Fitting position: Side) W5F- E <Port location: Axial ported> CDRB1 W5F- E- <Port location: Axial ported> 2 x One-touch fi tting (Fitting position: Axial direction) 2 x One-touch fitting (Fitting position: Axial direction) Applicable Tubing and O.D/I.D Applicable tubing O.D/I.D Applicable tubing material ø6/ø4 Nylon, Soft nylon, Polyurethane Dimensions not indicated in the above fi gures are the same as size 5 actuator. Keys in the fi gures above show the intermediate rotation position for single vane type. H D-M9 13

15 Rotary Actuator Nil D Rotary Auto switch Basic type With auto switch (With auto switch unit and built-in magnet) When ordering the rotary actuator with solenoid valve, CVRB1 series, specify the models of both the rotary and the valve (solenoid valve). Note) For the valve, add in front of the part number when ordering. Example) CDVRB1BW8-9S-R73 1 pc. VZ514-5LZ 1 pc. Solenoid Valve Valve Type of actuation 1 2-position single solenoid 2 2-position double solenoid W How to Order (Example) Valve series 3 VZ3 series C VRB1BW5,63 5 VZ5 series C VRB1BW8,1 Rated voltage 1 1 VAC 5/6 Hz 2 2 VAC 5/6 Hz 5 24 VDC Rotary Actuator with Solenoid Valve Series CVRB1 : 5, 63, 8, 1 B Basic L Foot Shaft type Double shaft (Long shaft key & Four chamfers) Rotating angle How to Order CDVRB1 B W 8 9 S M9B L S D Nil M Vane type Single vane Double vane Auto switch Without auto switch (Built-in magnet) Without D-M9 type auto switch (Built-in magnet) For applicable auto switch model, refer to the table below. The operating range and hysteresis of the D-M9 are different from those of the other auto switches. For details, refer to page 28. VZ L X199 Electrical entry Grommet L plug connector M plug connector DIN terminal G: Lead wire length 3 mm H: Lead wire length 6 mm L: With lead wire (Wire length: 3 mm) M: With lead wire (Wire length: 3 mm) D: With connector LO: Without connector MO: Without connector DO: Without connector Manual For details, refer to pages 17 to 19, 26 and 27. Number of auto switches S 1 pc. Nil 2 pcs. S: A right-hand auto switch is shipped. Nil: A right-hand switch and a left-hand switch are shipped. Electrical entry/lead wire length Nil Grommet/Lead wire:.5 m M Grommet/Lead wire: 1 m L Grommet/Lead wire: 3 m CN Connector/Without lead wire C Connector/Lead wire:.5 m CL Connector/Lead wire: 3 m Connectors are available only for the R73, R8, T79. Lead wire with connector part nos. D-LC5: Lead wire.5 m D-LC3: Lead wire 3 m D-LC5: Lead wire 5 m Nil: Non-locking push type Light/Surge voltage suppressor Nil Without light/surge voltage suppressor S With surge voltage suppressor Z Note) With light/surge voltage suppressor Note) GZ, HZ and DOZ are not available. Suffix For VZ3 series only B: Locking B type (Slotted) C: Locking C type (Manual) CVRB1 Auto Switch Applicable Auto Switches/Refer to the Best Pneumatics No.4 for further information on auto switches. Type Special function Solid state Grommet auto switch Reed auto switch Auto switch Lead wire length [m] Electrical Wiring Load voltage Lead wire Pre-wired Applicable model None entry (Output) type connector load DC AC Perpendicular In-line (Nil) (M) (L) (Z) (N) 3-wire (NPN) 5 V, M9NV M9N IC circuit 3-wire (PNP) 12 V M9PV M9P 2-wire 12 V M9BV M9B 3-wire (NPN) 5 V, S79 Oilproof IC circuit 3-wire (PNP) 12 V S7P heavyduty PLC Relay, 24 V T79 2-wire 12 V Connector T79C cord Grommet 1 V R73 Connector R73C 2-wire Grommet 48 V, 1 V 1 V R8 IC circuit Connector 24 V or less R8C Indicator light1 Yes Yes No Lead wire length symbols:.5 m Nil (Example) R73C 3 m L (Example) R73CL 5 m Z (Example) R73CZ None N (Example) R73CN Solid state auto switches marked with are produced upon receipt of order. 14

16 Series CVRB1 (For details, refer to pages 17 to 19, 26 and 27.) Symbol Description XA1 to XA24 Shaft type pattern XC1 Addition of connection port XC4 Change of rotating angle XC5 Change of rotating angle XC6 Change of rotating angle XC7 Reversed shaft XC26 Change of rotating angle XC27 Change of rotation range and direction XC3 Fluorine grease Refer to pages 28 to 3 for actuators with auto switches. Auto switch unit and switch block unit Operating range and hysteresis How to change the auto switch detecting position Auto switch mounting Auto switch adjustment Dimensions Solenoid Valve Specifications Model VZ3/5 series Manual override Non-locking push type Locking type (Slotted), Locking type (Manual) Pilot exhaust type Pilot valve individual exhaust position Free Impact/Vibration resistance [m/s 2 ] Note 1) 3/5 Enclosure Dusttight Electrical entry Coil rated voltage [V] Allowable voltage fluctuation [%] Grommet (G)/(H), L plug connector (L), M plug connector (M), DIN terminal (D) AC 5/6 Hz 1, 2 DC to +1 of rated voltage Power consumption [W] [Current ma] Note 2) DC 1.8 (With light: 2.1) (24 VDC: 75 [With light: 87.5]) Apparent power [VA] Note 2) [Current ma] AC Inrush 4.5 to 5 Hz, 4.2/6 Hz Holding 3.5/5 Hz, 3/6 Hz 1 VAC: 45/5 Hz, 42/6 Hz 2 VAC: 22.5/5 Hz, 21/6 Hz 1 VAC: 35/5 Hz, 3/6 Hz 2 VAC: 17.5/5 Hz, 15/6 Hz Surge voltage suppressor DC: Diode, AC: ZNR Indicator light DC: LED (Red), AC: Neon bulb Option Note 1) Impact resistance: No malfunction occurred in the impact test using a drop impact tester. The test was performed at both energized and de-energized states to the axis and right angle direction of the main valve and armature. Vibration resistance: No malfunction occurred in the one-sweep test between 45 and 2 Hz. A test was performed at both energized and de-energized states to the axis and right angle direction of the main valve and armature. (Value in the initial stage.) Note 2) At the rated voltage. About rotary actuator specifications The vibration adjustment range differs from that of the standard series. With solenoid valve:.3 to 1 s/9 Other specifi cations and structures are similar to those of the standard series. Refer to pages 4 and 9. Solenoid B (When double solenoid is mounted) Keys in the fi gures below show the intermediate rotation position for single vane type. Solenoid A C2 (When double solenoid is mounted) B2 B3 (When the needle is fully open) 15 2 x metering valve with silencer (EXH) ASN2-M5 (CVRB1BW5) ASN2-1 (CVRB1BW8, 1) Note 1) Solenoid valve in external appearance is for 3 VZ 514-1G. Note 2) Solenoid valve dimensions: 2-position single solenoid, ( ): 2-position double solenoid. F2 (When double solenoid is mounted) A1 A2 B1 B2 B3 C1 C2 C3 D1 D2 E1 E2 F1 F2 G R (136.5) 6 (61) (53) 14 (12.5) 25 1/ (136.5) 6 (61) (53) 14 (12.5) / (155 ) 7 (71) (63) 124 (139 ) 36 1/ (155 ) 7 (71) (63) 124 (139 ) /8

17 Auto Switch CVRB1 16

18 Series (: 5, 63, 8, 1) -XA1 to -XA24: Shaft Pattern Sequencing! Shaft shape pattern is dealt with simple made-to-order system. (Refer to the Best Pneumatics No.4.) Please contact SMC for a specifi cation sheet when placing an order. Shaft Pattern Sequencing! Symbol -XA1 to XA24 Applicable shaft type: W (Standard) Connecting port location Without auto switch C RB1BW 63 9 S E XA1C4C3 With auto switch CD RB1BW 63 9 S E M9B XA1C4C3 With solenoid valve (Refer to page 14.) Shaft type Vane type Rotating angle Auto switch Shaft pattern sequencing symbol Shaft Pattern Sequencing Symbol Axial: Top (Long shaft side) Symbol Description XA1 Shaft-end female thread XA14 Shaft through-hole + Shaft-end female thread XA17 Change of long shaft length (Change of key length) XA24 Double key The vane type for the shaft through-hole is compatible with single vanes only. Axial: Bottom (Short shaft side) Symbol Description XA2 Shaft-end female thread XA15 Shaft through-hole + Shaft-end female thread XA18 Change of short shaft length The vane type for the shaft through-hole is compatible with single vanes only. Double Shaft Symbol Description XA13 Shaft through-hole XA16 Shaft through-hole + Double shaft-end female threads XA19 Change of double shaft length XA2 Reversed shaft, Change of double shaft length The vane type for the shaft through-hole is compatible with single vanes only. The product with an auto switch is available only for XA1, 14, 17 and 24. Combination XA Combination Symbol Description Axial direction Up Down Combination XA1 Shaft-end female thread XA1 XA2 Shaft-end female thread XA2 XA13 Shaft through-hole XA13 XA14 Shaft through-hole + Shaft-end female thread XA14 XA15 Shaft through-hole + Shaft-end female thread XA15 XA16 Shaft through-hole + Double shaft-end female threads XA16 XA17 Change of long shaft length (Change of key length) XA17 XA18 Change of short shaft length XA18 XA19 Change of double shaft length XA19 XA2 Reversed shaft, Change of double shaft length XA2 XA24 Double key XA24 A total of two XA combinations is available. Example: XA1A24 XA, XC Combination Combination other than -XA, such as (-XC ), is also available. Refer to pages 26 to 27 for details about made-to-order specifi cations. Symbol Description XA1, XA2 XA13 to 2, 24 XC1 Addition of connection port XC4 Change of rotating angle XC5 Change of rotating angle XC6 Change of rotating angle 5, 63 XC7 Reversed shaft 8,1 XC26 Change of rotating angle XC27 Change of rotation range and direction XC3 Fluorine grease 17 A total of four XA and XC combinations is available. Example: XA1A24C1C3

19 Series Axial: Top (Long shaft side) Symbol: A1 Machine female threads into the long shaft. The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M3: L1 = 6 Applicable shaft type: W Axial: Bottom (Short shaft side) Symbol: A2 Machine female threads into the short shaft. The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M4: L2 = 8 Applicable shaft type: W Q1 = M Q1 = M L1 = L1 + (3 x P) Symbol: A14 Applicable to single vane type only A special end is machined onto the long shaft, and a through-hole is drilled into it. Female threads are machined into the through-holes, whose diameter is equivalent to the diameter of the pilot holes. The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M5: L1 = 1 Applicable shaft type: W Symbol: A17 Applicable shaft type: W L1 = Thread Shorten the long shaft. Q1 5 M3, M4, M5 63 M4, M5, M6 8 M4, M5, M6 1 M5, M6, M M5 x.8 ø4.2 ø4.2 ø4.2 M6 x 1 ø5 ø5 ø5 M8 x 1.25 ø6.8 L2 + (3 x P) Q2 = M L2 = Symbol: A15 Q2 = M Symbol: A18 Applicable to single vane type only A special end is machined onto the short shaft, and a through-hole is drilled into it. Female threads are machined into the through-hole, whose diameter is equivalent to the pilot hole diameter. The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M4: L2 = 8 Applicable shaft type: W Applicable shaft type: W L2 = Thread Shorten the short shaft. Q2 5 M3, M4, M5 63 M4, M5, M6 8 M4, M5, M6 1 M5, M6, M M5 x.8 ø4.2 ø4.2 ø4.2 M6 x 1 ø5 ø5 ø5 M8 x 1.25 ø6.8 CVRB1 Auto Switch X = X Y to to to 45 Y = 63 4 to to to to to 3 Symbol: A24 Double key Keys and keyways are machined at 18 of standard position. Applicable shaft type: W Equal dimensions are indicated by the same marker. LL Keyway dimensions LL Keyway dimension LL 5 4 x 4 x x 5 x x 5 x x 7 x 4 18

20 Series Double Shaft Symbol: A13 Applicable to single vane type only Shaft with through-hole Minimum machining diameter for d1 is.1. Applicable shaft type: W d1 = ø d1 5 ø4 to ø5 63 ø4 to ø6 8 ø4 to ø6.5 1 ø5 to ø8 Symbol: A16 Applicable to single vane type only A special end is machined onto both the long and short shafts, and a through-hole is drilled into both shafts. Female threads are machined into the through-holes, whose diameter is equivalent to the diameter of the pilot holes. The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M5: L1 = 1 Applicable shaft type: W Equal dimensions are indicated by the same marker. Q1 = M Thread Q1 L1 = L1 M5 x.8 ø4.2 ø4.2 ø4.2 M6 x 1 ø5 ø5 ø5 M8 x 1.25 ø6.8 Symbol: A19 Applicable shaft type: W Shorten both long and short shafts. Symbol: A2 The rotation axis is reversed. (If shortening the shaft is not required, indicate for dimension X, Y.) Applicable shaft type: W Y = X = X Y to to to 45 4 to to to to 65 5 to 3 Y = X = X Y 5 4 to to to to to to to 3 4 to 65 19

21 Series (: 5, 63, 8, 1) -XA31 to -XA6: Shaft Pattern Shaft shape pattern is dealt with simple made-to-order system. (Refer to the Best Pneumatics No.4.) Please contact SMC for a specifi cation sheet when placing an order. Shaft Pattern Applicable shaft type: J, K, S, T, X, Y, Z Shaft type J K S Refer to T page 8. X Y Z Connecting port location Symbol -XA31 to XA6 CVRB1 Without auto switch With auto switch Shaft Pattern Sequencing Symbol C RB1B J 63 9 S E CD With solenoid valve (Refer to page 14.) Shaft type J Refer to Z page 8. RB1B J 63 9 S E M9B XA33C4C3 Vane type Rotating angle Auto switch XA33C4C3 Shaft pattern sequencing symbol Axial: Top (Long shaft side) Symbol Description Shaft type XA31 Shaft-end female thread S, Y XA33 Shaft-end female thread J, K, T XA35 Shaft-end female thread X, Z 5, XA37 Stepped round shaft J, K, T 63, XA45 Middle-cut chamfer J, K, T 8, XA48 Change of long shaft length (With keyway) S, Y 1 XA51 Change of long shaft length (Without keyway) J, K, T XA54 Change of long shaft length (With four chamfers) X, Z Axial: Bottom (Short shaft side) Symbol Description Shaft type XA32 Shaft-end female thread S, Y XA34 Shaft-end female thread K, T XA36 Shaft-end female thread J, X, Z 5, XA38 Stepped round shaft K 63, XA46 Middle-cut chamfer K 8, XA49 Change of short shaft length (With keyway) Y 1 XA52 Change of short shaft length (Without keyway) K XA55 Change of short shaft length (With four chamfers) J, Z Double Shaft Symbol Description Shaft type XA39 Shaft through-hole S, Y XA4 Shaft through-hole K, T XA41 Shaft through-hole J, X, Z XA42 Shaft through-hole + Double shaft-end female threads S, Y XA43 Shaft through-hole + Double shaft-end female threads K, T 5, XA44 Shaft through-hole + Double shaft-end female threads J, X, Z 63, XA5 Change of double shaft length (Both sides with keyway) Y 8, XA53 Change of double shaft length (Without keyway) K XA56 Change of double shaft length (Both sides with four chamfers) Z 1 XA57 Change of double shaft length (With four chamfers, without keyway) J XA58 Reversed shaft, Change of double shaft length (With four chamfers, without keyway) J, T XA59 Reversed shaft, Change of shaft length (With four chamfers) X XA6 Reversed shaft, Change of shaft length (With keyway) S The vane type for the shaft through-hole is compatible with single vanes only. The product with an auto switch is available only for J and Z shafts of XA33, 35, 37 45, 51 and 54. Auto Switch 2

22 Series Combination XA Combination Axial direction Applicable shaft type Combination Symbol Description Up Down J K S T X Y Z These are shaft types that can be combined. XA31 Shaft-end female thread XA31 XA32 Shaft-end female thread XA32 XA33 Shaft-end female thread XA33 XA34 Shaft-end female thread XA34 XA35 Shaft-end female thread XA35 XA36 Shaft-end female thread J X, Z XA36 XA37 Stepped round shaft K, T J XA37 XA38 Stepped round shaft K XA39 Shaft through-hole XA4 Shaft through-hole XA41 Shaft through-hole XA42 Shaft through-hole + Double shaft-end female threads XA43 Shaft through-hole + Double shaft-end female threads XA44 Shaft through-hole + Double shaft-end female threads XA38 XA45 Middle-cut chamfer K, T J K XA39 XA4 XA41 XA45 XA46 Middle-cut chamfer K K K XA46 XA48 Change of long shaft length (With keyway) XA49 Change of short shaft length (With keyway) Y Y XA5 Change of double shaft length (Both sides with keyway) Y XA51 Change of long shaft length (Without keyway) K, T J K K, T J K XA52 Change of short shaft length (Without keyway) K K K XA53 Change of double shaft length (Without keyway) K XA54 Change of long shaft length (With four chamfers) X, Z X, Z XA55 Change of short shaft length (With four chamfers) J Z J J, Z J XA56 Change of double shaft length (Both sides with four chamfers) Z XA57 Change of double shaft length (With four chamfers, without keyway) J XA58 Reversed shaft, Change of double shaft length (With four chamfers, without keyway) T J XA59 Reversed shaft, Change of shaft length (With four chamfers) X XA6 Reversed shaft, Change of shaft length (With keyway) S Combinations of XA39 to XA44 with others are not available. The vane type for the shaft through-hole is compatible with single vanes only. A total of two XA combinations is available. Example: XA31A32 XA, XC Combination Combination other than XA, such as (XC ), is also available. Refer to pages 26 and 27 for details about made-to-order specifications. Symbol Description Applicable shaft type XA31 to XA6 J, K, S, T, X, Y, Z XC1 Addition of connection port XC4 Change of rotating angle XC5 Change of rotating angle XC6 Change of rotating angle XC7 Reversed shaft J, S, T, X XC26 Change of rotating angle XC27 Change of rotation range and direction XC3 Fluorine grease The vane type for the shaft through-hole is compatible with single vanes only. A total of four XA and XC combinations is available. Example: XA31A32C1C3 XA32C1C4C3 The product with an auto switch is available only for J and Z shafts of XA33, 35, 37, 45, 51 and

23 Series Axial: Top (Long shaft side) Symbol: A31 Machine female threads into the long shaft. The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M3: L1 = 6 Applicable shaft type: S, Y Axial: Bottom (Short shaft side) Symbol: A32 Machine female threads into the short shaft. The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M4: L2 = 8 Applicable shaft type: S, Y L1 + (3 x P) L1 = Q1 = M L1 = L1 + ( 3 x P) Symbol: A33 Machine female threads into the long shaft. The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M3: L1 = 6 Applicable shaft type: J, K, T Q1 = M Q1 S Y 5 M3, M4, M5 63 M4, M5, M6 8 M4, M5, M6 1 M5, M6, M8 Shaft type Q1 J K T 5 M3, M4, M5, M6 63 M4, M5, M6 8 M4, M5, M6, M8 1 M5, M6, M8, M1 Shaft type Symbol: A35 Machine female threads into the long shaft. The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M3: L1 = 6 Applicable shaft type: X, Z L2 + (3 x P) L2 = Q2 = M Q2 = M Y axis L2= L2 + (3 x P) K axis Q2 = M Q2 = M S axis L2 = L2 + (3 x P) Symbol: A34 Machine female threads into the short shaft. The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M3: L2 = 6 Applicable shaft type: K, T T axis L2 = L2 + (3 x P) Q2 S Y 5 M3, M4, M5, M6 M3, M4, M5 63 M4, M5, M6 M4, M5, M6 8 M4, M5, M6, M8 M4, M5, M6 1 M5, M6, M8, M1 M5, M6, M8 Shaft type Q2 K T 5 M3, M4, M5, M6 63 M4, M5, M6 8 M4, M5, M6, M8 1 M5, M6, M8, M1 Shaft type Symbol: A36 Machine female threads into the short shaft. The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M3: L2 = 6 Applicable shaft type: J, X, Z CVRB1 Auto Switch Q1 = M L1 = L1 + (3 x P) Q1 X Z 5 M3, M4, M5 63 M4, M5, M6 8 M4, M5, M6 1 M5, M6, M8 Shaft type X axis L2 = L2 + (3 x P) Q2 = M Q2 = M L2 + (3 x P) L2 = J, Z axis Q2 X J Z 5 M3, M4, M5, M6 M3, M4, M5 63 M4, M5, M6 M4, M5, M6 8 M4, M5, M6, M8 M4, M5, M6 1 M5, M6, M8, M1 M5, M6, M8 Shaft type Symbol: The long shaft can be further shortened by machining it into A37 a stepped round shaft. (If shortening the shaft is not required, indicate for dimension X.) (If not specifying dimension CA, indicate instead.) Equal dimensions are indicated by the same marker. Applicable shaft type: J, K, T Symbol: The short shaft can be further shortened by machining it into A38 a stepped round shaft. (If shortening the shaft is not required, indicate for dimension Y.) (If not specifying dimension CB, indicate instead.) Equal dimensions are indicated by the same marker. Applicable shaft type: K CA = C CA D1 = ø L1 = X = X L1 max D1 J K T J K T J K T 5 4 to 39.5 X-3 3 to to 45 X-3 3 to to 53.5 X-3 3 to to 65 X-4 3 to 24.9 Shaft type CB CB = C D2 = ø L2 = Y = Y L2 max D2 5 4 to 39.5 Y-3 3 to to 45 Y-3 3 to to 53.5 Y-3 3 to to 65 Y-4 3 to

24 Series W1 = Axial: Top (Long shaft side) Symbol: The long shaft can be further shortened by machining a A45 middle-cut chamfer into it. (The position of the chamfer is same as the standard one.) (If shortening the shaft is not required, indicate for dimension X.) Minimum machining dimension is.1. Applicable shaft type: J, K, T L3 = L1 = X = X = Shaft type Symbol: A48 Shorten the long shaft. Applicable shaft type: S, Y X W1 L1 max L3 max JKTJKTJKTJKT to to 6 X-3 L to 45 1 to 7.5 X-3 L to to 8.5 X-3 L to 65 1 to 12.5 X-4 L1-2 X to to to to 65 W2 Axial: Bottom (Short shaft side) Symbol: The short shaft can be further shortened by machining a A46 middle-cut chamfer into it. (The position of the chamfer is same as the standard one.) (If shortening the shaft is not required, indicate for dimension X.) Minimum machining dimension is.1. Applicable shaft type: K L4 = Y = L2 = Y = Symbol: A49 Shorten the short shaft. Applicable shaft type: Y Y W2 L2 max L4 max to to 6 Y-3 L to 45 1 to 7.5 Y-3 L to to 8.5 Y-3 L to 65 1 to 12.5 Y-4 L2-2 Y to to to to 65 Symbol: A51 Shorten the long shaft. Applicable shaft type: J, K, T X 5 4 to 39.5 X = 63 4 to to to 65 Symbol: A52 Shorten the long shaft. Applicable shaft type: K Y 5 4 to 39.5 Y = 63 4 to to to 65 Symbol: A54 Shorten the long shaft. Applicable shaft type: X, Z X = X 5 4 to to to to 3 Symbol: A55 Shorten the short shaft. Applicable shaft type: J, Z Y Y = 5 4 to to to to 3 Caution For the shaft patterns A45 and A46, a middle-cut chamfer may interfere with the center hole if the W1/W2 dimensions and (L1 L3), (L2 L4) dimensions are less than what are shown in the table below. W1 W2 L1-L3 L2-L to 6 2 to to to to to to to Symbol: A59 Reverse the assembly of the shaft, and shorten the long shaft. Applicable shaft type: X Y 5 4 to 19.5 Y = Y = 63 4 to to to 3 Symbol: A6 Reverse the assembly of the shaft, and shorten the long shaft. Applicable shaft type: S Y to to to to 65

25 Series Double Shaft Symbol: A39 Applicable to single vane type only Symbol: A4 Shaft with through-hole Minimum machining diameter for d1 is.1. Applicable shaft type: S, Y d1 = ø d1 = ø d1 d1 = ø d1 = ø Shaft type S Y 5 ø4 to ø5 63 ø4 to ø6 8 ø4 to ø6.5 S axis 1 ø5 to ø8 T axis Y axis K axis Symbol: A41 Applicable to single vane type only Shaft with through-hole Minimum machining diameter for d1 is.1. Applicable shaft type: J, X, Z d1 = ø J axis L1 = L1 d1 = ø Z axis Symbol: A43 Applicable to single vane type only A special end is machined onto both the long and short shafts, and a through-hole is drilled into both shafts. Female threads are machined into the through holes, whose diameter is equivalent to the diameter of the pilot holes. The maximum dimension L1 is, as a rule, twice the thread size. Applicable shaft type: K, T Equal dimensions are indicated by the same marker. Q1 = M Q1 = M Shaft type Thread K T K T K T K T M5 x.8 ø4.2 ø4.2 ø4.2 ø4.2 M6 x 1 ø5 ø5 ø5 ø5 M8 x 1.25 ø6.8 ø6.8 Q1 Q1 K axis T axis M1 x 1.5 ø8.6 L1 = L1 Symbol: A5 Shorten both long and short shafts. Applicable shaft type: Y d1 J X Z 5 ø4 to ø5 63 ø4 to ø6 8 ø4 to ø6.5 1 ø5 to ø8 Shaft type Applicable to single vane type only Shaft with through-hole Minimum machining diameter for d1 is.1. Applicable shaft type: K, T Symbol: A42 Applicable to single vane type only A special end is machined onto both the long and short shafts, and a through-hole is drilled into both shafts. Female threads are machined into the through-holes, whose diameter is equivalent to the diameter of the pilot holes. The maximum dimension L1 is, as a rule, twice the thread size. Applicable shaft type: S, Y Equal dimensions are indicated by the same marker. Q1 Q1 = M L1 S axis Symbol: A44 L1 = L1 L1 = Q1 = M Q1 Y axis L1 = L1 L1 L1 = A special end is machined onto both the long and short shafts, and a through-hole is drilled into both shafts. Female threads are machined into the through-holes, whose diameter is equivalent to the diameter of the pilot holes. The maximum dimension L1 is, as a rule, twice the thread size. Applicable shaft type: J, X, Z Equal dimensions are indicated by the same marker. Q1=M Q1=M Shaft type Thread JXZJXZJXZJXZ M5 x.8 ø4.2 ø4.2 ø4.2 ø4.2 M6 x 1 ø5 ø5 ø5 Q1 Q1 M8 x 1.25 ø6.8 J axis Applicable to single vane type only Z axis Symbol: A53 Shorten both long and short shafts. Applicable shaft type: K d1 K T 5 ø4 to ø ø4 to ø 6 8 ø4 to ø ø5 to ø1 Shaft type Shaft type Thread S Y S Y S Y S Y M5 x.8 ø4.2 ø4.2 ø4.2 ø4.2 M6 x 1 ø5 ø5 ø5 M8 x 1.25 ø6.8 CVRB1 Auto Switch Y = X = X Y to to to to to to to 65 4 to 65 Y = X = X Y 5 4 to to to 45 4 to to to to 65 5 to 65 24

26 Series Double Shaft Symbol: A56 Shorten both long and short shafts. Applicable shaft type: Z Symbol: A57 Shorten both long and short shafts. Applicable shaft type: J X = X = X Y X Y 5 4 to to to to 19.5 Y = 63 4 to 21 4 to to to 23.5 Y = 63 4 to 45 4 to to to to 3 5 to to 65 5 to 3 Symbol: A58 The rotation axis is reversed. The long shaft and short shaft are shortened. (If shortening the shaft is not required, indicate for dimension X, Y.) Applicable shaft type: J, T X = Y = X Y 5 4 to to to 21 4 to to to to 3 5 to 65 25

27 Series (: 5, 63, 8, 1) XC1, 4, 5, 6, 7, 26, 27, 3 How to Order Shaft type W J K S T X Y Z Standard Refer to page 8. Connecting port location CVRB1 Without auto switch With auto switch C CD RB1B With solenoid valve (Refer to page 14.) Shaft type W Standard J Refer to Z page 8. RB1B W 63 9 S E XC4C3 W 63 9 S E M9B XC4C3 Vane type Rotating angle Auto switch Made-to-Order symbol Made-to-Order Symbol Symbol Description Applicable shaft type W, J, K, S, T, X, Y, Z XC1 Addition of connection port XC4 Change of rotating angle XC5 Change of rotating angle XC6 Change of rotating angle XC7 Reversed shaft XC26 Change of rotating angle XC27 Change of rotation range and direction XC3 Fluorine grease 5, 63, 8, 1 This specifi cation is not available for rotary actuators with auto switch unit. Combination Symbol Combination XC1 XC3 XC1 XC4 XC5 XC6 XC7 XC26 XC27 XC3 Auto Switch Symbol: C1 Add connection ports on Body (A). (An additionally machined port will have an aluminum surface since it will be left unfi nished.) Symbol: C4 Change of rotating angle. (Applicable to single vane type only) Start of rotation is horizontal line (9 down from the top to the right side). Body (B) End of rotation Rotation range M N Body (A) Q Q M N 5 Rc1/ Rc1/ Rc1/ Rc1/ (9 ) Key position (Start of rotation) Rotation range θ 45 +8, 9 +8, Start of rotation is the position of the key when is pressurized. (Top view from long shaft side) 26

28 X Series Symbol: C5 Change of rotating angle. (Applicable to single vane type only) Start of rotation is 45 up from the bottom of the vertical line to the left side. Symbol: C6 Change of rotating angle. (Applicable to single vane type only) Start of rotation is horizontal line (9 down from the top to the left side). Key position (Start of rotation) Rotation range (45 ) End of rotation Rotation range θ 45 +8, 9 +6, , Key position (Start of rotation) Rotation range (9 ) End of rotation Rotation range θ 45 +8, 9 +8, Start of rotation is the position of the key when is pressurized. (Top view from long shaft side) Symbol: C7 The shafts are reversed. Start of rotation is the position of the key when is pressurized. (Top view from long shaft side) Symbol: C26 Change of rotating angle. (Applicable to single vane type only) Start of rotation is 45 up from the bottom of the vertical line to the right side. Body (B) Body (A) Symbol: C27 Y Y X Change of rotating angle. (Applicable to double vane type only) Rotating angle 9 Start of rotation is 45 up from the bottom of the vertical line of the right side. End of rotation Rotation range Symbol: C3 Key position (Start of rotation) (45 ) Rotation range θ 45 +8, 9 +6, , Start of rotation is the position of the key when is pressurized. (Top view from long shaft side) Change the standard grease to fl uorine grease. (Not for low-speed specifi cation.) End of rotation (45 ) Rotation range Key position (Start of rotation) Start of rotation is the position of the key when is pressurized. (Top view from long shaft side) 27

29 Series Auto Switch Auto Switch Unit and Switch Block Unit Unit Part Number For D-M9 For D-S/T79, D-R73/8 Auto switch unit Switch block unit part number Auto switch unit Switch block unit part number 2 part number 1 Common to right-hand and left-hand part number 1 For right-hand For left-hand 5 P4112-1M P P P P4113-1M P P8111-8M 8 P4114-1M P P P P4115-1M P An auto switch will not be included, please order it separately. 2 Auto switch unit comes with one right-hand and one left-hand switch blocks that are used for addition or when the switch block is damaged. Operating Range and Hysteresis Operating range: θ m The range between the position where the auto switch turns ON as the magnet inside the auto switch unit moves and the position where the auto switch turns OFF as the magnet travels the same direction. Hysteresis range: θ d The range between the position where the auto switch turns ON as the magnet inside the auto switch unit moves and the position where the auto switch turns OFF as the magnet travels the opposite direction. Auto switch OFF m: Operating range Actuated position: ON d: Hysteresis range (OFF) Magnet D-M9 θ m: Operating range θ d: Hysteresis range , 8, D-S/T79, D-R73/8 θ m: Operating range θ d: Hysteresis range , 8, Note) Since the fi gures in the above table are provided as a guideline only, they cannot be guaranteed. Adjust the auto switch after confi rming the operating conditions in the actual setting. CVRB1 Auto Switch How to Change the Auto Switch Detecting Position When setting the detecting position, loosen the cross recessed round head screw a bit and move the auto switch to the preferred position and then tighten again and fix it. At this time, if tightened too much, screw can become damaged and unable to fix position. Proper tightening torque:.4 to.6 [N m] When tightening the cross recessed round head screw, take care that the auto switch does not tilt. Cross recessed round head screw Cross recessed round head screw D-M9 : 5 to 1 D-S/T79 D-R73/R8 : 5 to 1 28

30 Series Auto Switch External view and descriptions of auto switch unit The following shows the external view and typical descriptions of the auto switch unit. Cross recessed round head screw Slotted set screw Cover (B) Switch holder Cover (A) Cross recessed round head screw (1) Switch block (A) Cover (B) Switch block (B) Cover (A) Cross recessed round head screw (2) Procedure <Applicable auto switch> Solid state auto switch D-M9 1. Auto switch mounting Insert the auto switch into the groove of the switch holder. Procedure <Applicable auto switch> Solid state auto switch D-S79, S7P D-T79, T79C Reed auto switch D-R73/R73C (With indicator light) D-R8/R8C (Without indicator light) 1. Auto switch mounting Loosen the cross recessed round head screw (2), and insert the arm of the auto switch. Arm 2. Auto switch securing Align the auto switch with the lower surface of the groove on the side of the switch holder, and secure the slotted set screw. (Refer to the enlarged view.) 2. Auto switch securing Set the auto switch so that it is in contact with the switch block, and tighten the cross recessed round head screw (2). Proper tightening torque:.4 to.6 [N m] Proper tightening torque:.5 to.1 [N m] Align with the groove lower surface to secure. Slotted set screw Enlarged view 3. Switch holder securing After the actuated position has been adjusted with the cross recessed round head screw, use the auto switch. When tightening the screw, take care that the auto switch does not tilt Switch holder securing After the actuated position has been adjusted with the cross recessed round head screw (1), use the auto switch. Proper tightening torque:.4 to.6 [N m]

Vane Type Rotary Actuator 50, 63, 80, 100

Vane Type Rotary Actuator 50, 63, 80, 100 Vane Type Rotary Actuator 5, 63, 8, 1 New Compact auto switches are mountable! (D-M9 ) Compact auto switch D-M9 Stainless steel specification for main parts : 5, 63, 8, 1 Special screw Hexagon socket head

More information

Rotary Actuator/Vane Type

Rotary Actuator/Vane Type Rotary Actuator/Vane Type CRB1 Series : 5, 63, 8, 1 Compact auto switches can be used! (D-M9 ) CRB 2 CRB1 MSU CRJ CRA1 CRQ2 MSQ MSZ CRQ2X MSQX MRQ Compact auto switch D-M9 Stainless steel specification

More information

Series CRB1. Rotary Actuator Vane Style. Size: 50, 63, 80, 100 CRB2 CRBU2 CRB1 MSU CRJ CRA1 CRQ2 MSQ MRQ D- Series Variations. Standard.

Series CRB1. Rotary Actuator Vane Style. Size: 50, 63, 80, 100 CRB2 CRBU2 CRB1 MSU CRJ CRA1 CRQ2 MSQ MRQ D- Series Variations. Standard. Rotary Actuator Vane Style Series : 5,, 8, Series Variations Standard Vane Port location Rotating angle Option Fluid Single vane (S) ouble vane () Side ported (Nil) Axial ported (E) 9 18 27 19 28 ouble

More information

Rotary Actuator. New RoHS. New. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB 2. Standard type/series CRB2

Rotary Actuator. New RoHS. New. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB 2. Standard type/series CRB2 Rotary Actuator Vane Type 1, 15, 2, 3, 4 Standard Type Free Mount Type Many combinations available! Standard type/series Piping ports are located on the flat surface. Fittings can be secured firmly, piping

More information

Rotary Actuator/Vane Type

Rotary Actuator/Vane Type Rotary Actuator/Vane Type CRB2 Series : 1, 15, 2, 3, 4 Standard Type Free Mount Type Many combinations available! Standard type/crb2 Series Piping ports are located on the flat surface. Fittings can be

More information

Rotary Actuator. New. New RoHS. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB2. Two shaft options available

Rotary Actuator. New. New RoHS. Vane Type 10, 15, 20, 30, 40. Many combinations available! Series CRB2. Two shaft options available Rotary Actuator Vane Type,,,, Many combinations available! New RoHS Two shaft options available With auto switch unit New Port locations modified Change in angle: Parallel piping ( ), Conventional type

More information

Rotary Actuator/Vane Style

Rotary Actuator/Vane Style Rotary Actuator/Vane Style Series :,,,, Basic style Series With angle adjuster Series BWU Fluid Air, CR Vane type Port location Single vane (S) ouble vane () Side ported (Nil) Axial ported (E) S Side ported

More information

Series CRB2. Rotary Actuator Vane Style. Size: 10, 15, 20, 30, 40 CRB2 CRBU2 CRB1 MSU CRJ CRA1 CRQ2 MSQ MRQ D- 20- Series Variations.

Series CRB2. Rotary Actuator Vane Style. Size: 10, 15, 20, 30, 40 CRB2 CRBU2 CRB1 MSU CRJ CRA1 CRQ2 MSQ MRQ D- 20- Series Variations. Rotary Actuator Vane Style Series :,,,, 4 1 Series Variations Standard Vane type Port location Rotating angle Shaft type Fluid (S) ouble vane () Side ported (Nil) Axial ported (E) 9 18 27 ouble shaft W

More information

Series MSU. Rotary Table Vane Style. High Precision. Size: 1, 3, 7, 20 CRB2 CRBU2 CRB1 MSU CRJ CRA1 CRQ2 MSQ MRQ D mm or less.

Series MSU. Rotary Table Vane Style. High Precision. Size: 1, 3, 7, 20 CRB2 CRBU2 CRB1 MSU CRJ CRA1 CRQ2 MSQ MRQ D mm or less. Rotary Table Vane Style Series Size: 1, 3, 7, 20 Table top deflection mm or less High Precision Peripheral table deflection mm or less Series B Series A 11-5-1 Rotary High precision type Size: 1, 3, 7,

More information

Rotary Table/Vane Style

Rotary Table/Vane Style Rotary Table/Vane Style Series Size: 1, 3, 7, 20 Table top deflection mm or less High Precision Peripheral table deflection mm or less X Series B Series A 147 Rotary Table Values inside ( ) are for Series

More information

Series VZ Port Solenoid Valve Body Ported. How to Order VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN. Body ported VZ L

Series VZ Port Solenoid Valve Body Ported. How to Order VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN. Body ported VZ L Port Solenoid Valve Body Ported Series 000 For details about certified products conforming to international standards, visit us at www.smcworld.com. Type of actuation Type of actuation Rated voltage Body

More information

Rotary Table/Vane Style

Rotary Table/Vane Style Rotary Table/Vane Style Series MSU Size: 1, 3, 7, 20 Table top deflection mm or less High Precision Peripheral table deflection mm or less CRB2 CRBU2 CRB1 MSU CRJ CRQ2 MSQ MSZ CRQ2X MSQX MRQ Series MSUB

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR2 CRU2 CR1 MSU CRJ Rotation 360 type MSQ 360 MSZ MSQ MRQ Series Variations Page Rotating angle 80 to 0 170

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator CRQ2 Series Rack & Pinion Type/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CR 2 CR1 MSU CRJ CR1 CRQ2 MSQ MSZ Rotation 360 type 360 CRQ2 MSQ MRQ Series Variations Page Rotating angle

More information

Series MSU. Rotary Table. High Precision. Vane Type/Sizes 1, 3, 7, 20. High precision series MSUA introduced to vane type rotary tables CAT.

Series MSU. Rotary Table. High Precision. Vane Type/Sizes 1, 3, 7, 20. High precision series MSUA introduced to vane type rotary tables CAT. CAT.ES20-90 C Rotary Table Series MSU Vane Type/Sizes 1, 3, 7, 20 Peripheral table deflection Table top deflection mm or less High Precision mm or less Series MSUB Series MSUA High precision series MSUA

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary ctuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm 360 type 360 CR2 CRU2 CR1 MSU CRJ CR1 MSQ MSZ MSQ MRQ Series Variations Standard Made to Order Rotating angle

More information

Series VZ Port Solenoid Valve Body Ported. How to Order VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Type of actuation. Option.

Series VZ Port Solenoid Valve Body Ported. How to Order VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN Type of actuation. Option. Port Solenoid Valve Body Ported Series 000 For details about certified products conforming to international standards, visit us at www.smcworld.com. Type of actuation Type of actuation Body option Body

More information

Compact Rotary Actuator

Compact Rotary Actuator Compact Rotary Actuator Series Rack & Pinion Style/:,,,, : 17 mm : mm : 29 mm : 33 mm : 37 mm CRB2 CRBU2 CRB1 MSU CRJ CRA1 Rotation 360 type 360 MSZ MRQ Series Variations Page Rotating angle 80 to 0 170

More information

Rack & Pinion Type/Size: 30, 50, 63, 80, 100. Compact auto switches are mountable. (D-M9 ) Rotating angle. Rotating. angle

Rack & Pinion Type/Size: 30, 50, 63, 80, 100. Compact auto switches are mountable. (D-M9 ) Rotating angle. Rotating. angle Rotary Actuator Series Rack & Pinion Type/: 3, 5, 63, 8, 1 Compact auto switches are mountable. (D-M9 ) Width reduced by up to 14 mm Space saving by changing the auto switch rail mounting to groove mounting.

More information

Mini Rotary Actuator/Rack & Pinion Style

Mini Rotary Actuator/Rack & Pinion Style Mini Rotary Actuator/Rack & Pinion Style Series CRJ :, CRB2 CRBU2 CRB MSU CRJ CRA CRA CRQ2 MSQ MSZ CRQ2X MSQX MRQ PAT. PEND D- 79 Mini Rotary Actuator Series CRJ Rack & Pinion Style/:, Compact 9.5 23.5

More information

Mini Rotary Actuator/Rack & Pinion Style

Mini Rotary Actuator/Rack & Pinion Style Mini Rotary Actuator/Rack & Pinion Style Series CRJ :, CRB2 CRBU2 CRB MSU CRJ CRA CRQ2 MSQ MSZ CRQ2X MSQX MRQ PAT. PEND D- 79 Mini Rotary Actuator Series CRJ Rack & Pinion Style/:, Compact 9.5 23.5 43(54)

More information

Series VZ Port Solenoid Valve Body Ported. How to Order VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN. Body ported VZ L

Series VZ Port Solenoid Valve Body Ported. How to Order VK VZ VF VFR VP4 VZS VFS VS4 VQ7 EVS VFN. Body ported VZ L Port Solenoid Valve Body Ported Series 000 For details about certified products conforming to international standards, visit us at www.smcworld.com. Type of actuation Type of actuation Rated voltage Body

More information

Rotary Actuator. New RoHS. Compact auto switches are mountable. Weight is reduced by up to 14 %. Mounting interchangeable with the current model

Rotary Actuator. New RoHS. Compact auto switches are mountable. Weight is reduced by up to 14 %. Mounting interchangeable with the current model Rotary Actuator Ø 30, Ø 50, Ø 63, Ø 80, Ø 100 New RoHS Compact auto switches are mountable. (D-M9 ) Width reduced by up to 14 mm Space saving by changing the auto switch rail mounting to groove mounting.

More information

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8

Precision Cylinder. MTS Series. ø8, ø12, ø16, ø20, ø25, ø32, ø40 MXH MXS MXQ MXQ MXF MXW MXJ MXP MXY MTS D- -X. Series Variations MTS8 Precision Cylinder Series, ø, ø6, ø, ø, ø, ø MXS Series Variations Model 8 Standard stroke (mm) 7 7 Rod end configuration Cushion Rubber bumper End lock Made to Order Rod Variable stroke/ through-hole

More information

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations.

Free Mount Cylinder. Series CU. A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Free Mount Cylinder Series CU A space-saving air cylinder with multiple surfaces capable of mounting directly. Offered in rich variations. Space-saving The multiple surface direct mounting with a square

More information

Compact Slide. Series MXH ø6, ø10, ø16, ø20

Compact Slide. Series MXH ø6, ø10, ø16, ø20 Compact Slide Series ø, ø, ø, ø The use of an endless track linear guide produces a table cylinder having excellent rigidity, linearity and non-rotating accuracy. Endless track linear guide Series Variations

More information

5 Port Direct Operated Poppet Solenoid Valve, Rubber Seal

5 Port Direct Operated Poppet Solenoid Valve, Rubber Seal Port Direct Operated Poppet Solenoid Valve, Rubber Seal Series 3000 or details about certified products conforming to international standards, visit us at www.smcworld.com. C: 0.4 dm 3 /(s bar) (Passage

More information

Exhausting equipment for pilot valve not required. Common exhaust port for main and pilot valve (VF1000/3000)

Exhausting equipment for pilot valve not required. Common exhaust port for main and pilot valve (VF1000/3000) 5 Port Pilot Operated Solenoid Valve Rubber Seal Series 1000/3000/5000 Large flow capacity Yet compact size. Low power consumption 1.8 W (DC) Exhausting equipment for pilot valve not required. Common exhaust

More information

Rotary Actuator Rack & Pinion Style

Rotary Actuator Rack & Pinion Style Rotary Actuator Rack & Pinion Style Series CRA1 :, 0, 63, 80, 0 Models with cushion or with solenoid valve available. (Only sizes 0 or larger are available.) Angle adjustment is possible. Fine angle adjuster

More information

Specifications. Fluid Ambient and fluid temperature ( C)

Specifications. Fluid Ambient and fluid temperature ( C) Series 0-V00 Rubber seal port direct operated solenoid valve Specifications Fluid Ambient and fluid temperature ( C) Note ) Response time (DC) ms Max. operating frequency (Hz) Manual override Lubrication

More information

5 Port Solenoid Valve Direct Operated Poppet Type. Specifications

5 Port Solenoid Valve Direct Operated Poppet Type. Specifications Port Solenoid Valve Direct Operated Poppet Type 000 Series Rubber Seal [Option] C: 0. dm /(s bar) (Passage {/ / (A/B R/R)}) Compact: Width 8 x Length 8 (mm) Low power consumption W DC (Standard type) W

More information

Electric Cylinder. LZB/LZC Series. It can be operated like an air cylinder. LZB Series. LZC Series LEF LEJ LEL LEM LEY LES LER LEH 25A- LEC

Electric Cylinder. LZB/LZC Series. It can be operated like an air cylinder. LZB Series. LZC Series LEF LEJ LEL LEM LEY LES LER LEH 25A- LEC Electric Cylinder LZB/LZC Series It can be operated like an air cylinder. LZB Series LZC Series Model LZB LZC Max. thrust Max. speed 196 N 0 mm/s Lead screw Slide screw: ø8, ø Lead: 2, 6, Stroke 25, 40,

More information

Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43

Free Mount Cylinder. Series. Series CU CAT.EUS20-95 B -UK. Space-saving. Auto Switch Capable P. 4, 23, 37 P. 45 P. 43 CAT.EUS- B -UK Free Mount Cylinder A space-saving air cylinder with multiple surfaces capable of direct mounting. Offered in many variations. Space-saving The multiple surface direct mounted rectangular

More information

Guide Table. MGF Series

Guide Table. MGF Series Guide Table MGF Series ø, ø, ø0 Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting.

Compact Cylinder: Standard Type Double Acting, Single Rod. How to Order 30 D F9BW. Body option <Standard stroke> Nil C M. Double acting. Compact Cylinder: Type Series ø, ø, ø, ø How to Order Without auto switch D With auto switch CDQS D FW S Number of auto switches L F G D, uilt-in magnet Mounting style Through-hole/oth ends tapped common

More information

Rotary Actuator Rack & Pinion Style

Rotary Actuator Rack & Pinion Style Rotary Actuator Rack & Pinion Style Series :,,, 8, s with cushion or with solenoid valve available. (Only sizes or larger are available.) Angle adjustment is possible. Fine angle adjuster is standard equipment.

More information

10, 15, 20, 30, 40 MSQX

10, 15, 20, 30, 40 MSQX Possible to transfer a workpiece at low-speed. Rotation time adjustment range: 1 to 5 ( s/90 ) Lowspeed Standard Low-Speed Rotary ctuator / Series :,,,, :,,, Model,,,,,,,,,,,,,, Rotation time adjustment

More information

Series VP4 50/4 70. Large Size 5 Port Solenoid Valve Rubber Seal SJ SY SY SV SYJ SZ VF VP4 S0700 VQ VQ4 VQ5 VQC VQC4 VQZ SQ VFS VFR VQ7 VP4

Series VP4 50/4 70. Large Size 5 Port Solenoid Valve Rubber Seal SJ SY SY SV SYJ SZ VF VP4 S0700 VQ VQ4 VQ5 VQC VQC4 VQZ SQ VFS VFR VQ7 VP4 Type of actuation 4 Piping 0 Side ported Bottom ported 4 Without sub-plate Large Size 5 Port Solenoid Valve Rubber Seal Series 50/4 70 Series VP 5 port solenoid valve 5 7 position single position double

More information

3 Port Solenoid Valve Direct Operated Poppet Type

3 Port Solenoid Valve Direct Operated Poppet Type 3 Port Solenoid Valve Direct Operated Poppet Type VK300 Series Rubber Seal [Option] Universal porting Available for N.C. valve, N.O. valve, divider valve, selector valve, etc. C: 0.80 dm 3 /(s bar) (Passage

More information

5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported. Flow characteristics 1 4/2 (P A/B) 4/2 5/3 (A/B R1/R2)

5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported. Flow characteristics 1 4/2 (P A/B) 4/2 5/3 (A/B R1/R2) For details about certified products conforming to international standards, visit us at www.smcworld.com. 5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported Series VFS3000 Model position 3 position

More information

Series CRQ2. Compact Rotary Actuator. Piping can be installed from one end. Body can be used as a flange Compact design saves mounting space

Series CRQ2. Compact Rotary Actuator. Piping can be installed from one end. Body can be used as a flange Compact design saves mounting space Compact Rotary Actuator Series CR2 Rack Pinion Style/:,,,, Piping can be installed from one end Uses internal cushioning, : Rubber bumper,, : Air cushion Angle adjustment bolts are standard Use of double

More information

5 Port Solenoid Valve Direct Operated Poppet Type. Specifications

5 Port Solenoid Valve Direct Operated Poppet Type. Specifications Port Solenoid Valve Direct Operated Poppet Type Series 000 Rubber Seal [Option] C: 0. dm /(s bar) (Passage {/ / (A/B R/R)}) Compact: Width 8 x Length 8 (mm) Low power consumption W DC (Standard type) W

More information

5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported

5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported For details about certified products conforming to international standards, visit us at www.smcworld.com. 5 Port Pilot Operated Solenoid Valve Metal Seal, Body Ported Series VFS2000 Model 2 position 3

More information

Guide Table. ø40, ø63, ø100

Guide Table. ø40, ø63, ø100 Guide Table Series MGF ø, ø, ø Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

3 Port Solenoid Valve

3 Port Solenoid Valve Port Solenoid Valve V00 Series Rubber Seal Power consumption 0. W (with power saving circuit) Note) Refer to page 7 for details. temperature rises: C (with power saving circuit) Sonic conductance Series

More information

5 Port Pilot Operated Solenoid Valve Rubber Seal, Plug-in/Non Plug-in. Standard Specifications. Fluid Operating pressure range

5 Port Pilot Operated Solenoid Valve Rubber Seal, Plug-in/Non Plug-in. Standard Specifications. Fluid Operating pressure range For details about certified products conforming to international standards, visit us at www.smcworld.com. Port Pilot Operated Solenoid Valve Rubber Seal, Plug-in/Non Plug-in Series VFR2 JIS Symbol type

More information

Compact Guide Cylinder Series MGQ

Compact Guide Cylinder Series MGQ Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø0 ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

Compact auto switches are mountable. (D-M9 ) Compact auto switches are mountable on 2 surfaces. Mounting interchangeable with the existing model

Compact auto switches are mountable. (D-M9 ) Compact auto switches are mountable on 2 surfaces. Mounting interchangeable with the existing model Rotary Actuator ø, ø, ø, ø New RoS Compact auto switches are mountable. (D-M9) Compact auto switches are mountable on 2 surfaces. New CRA1 Existing model Compact auto switch Width reduced by up to 14 mm

More information

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E -UK Dual-Rod Cylinder Series New: Dual-Rod Cylinder with Air Cushion Compact Type Series J Dual-Rod Cylinder with guide function for pick-and-place applications Series! Twice the thrust Non-rotating

More information

Series CRQ2. Compact Rotary Actuator Rack & Pinion Style. Size: 10, 15, 20, 30, 40. Rotary actuator body serves as a flange.

Series CRQ2. Compact Rotary Actuator Rack & Pinion Style. Size: 10, 15, 20, 30, 40. Rotary actuator body serves as a flange. Compact Rotary ctuator Rack & Pinion Style Series CRQ2 :,,,, Unidirectional pipe connection possible uilt-in cushion, : Rubber bumper,, : ir cushion Equipped with an angle adjusting mechanism Double piston

More information

Miniature Guide Rod Cylinder ±0.1. Mounting from 2 directions

Miniature Guide Rod Cylinder ±0.1. Mounting from 2 directions Miniature Guide Rod Cylinder Series Non-rotating accuracy : Height ±0.1 Mounting from 2 directions idth Overall length Two auto switches can be mounted even for mm strokes Integral wiring/piping to one

More information

5 Port Pilot Operated Solenoid Valve Rubber Seal. Specifications Fluid Operating pressure range (1) Response time 3 position (2) Enclosure

5 Port Pilot Operated Solenoid Valve Rubber Seal. Specifications Fluid Operating pressure range (1) Response time 3 position (2) Enclosure For details about certified products conforming to international standards, visit us at www.smcworld.com. Port Pilot Operated Solenoid Valve Series 000 Compact and lightweight: 3 mm width Compact yet provides

More information

Guide Table. Series MGF

Guide Table. Series MGF Guide Table Series MGF ø, ø, ø0 Low-profile compact cylinder utilizes a large concentric guiding sleeve to provide excellent eccentric load resistance. Mounting height greatly reduced Low-profile cylinder

More information

5 Port Solenoid Valve

5 Port Solenoid Valve 5 Port Solenoid Valve Series VFR//4/5/6 Rubber Seal Series Variations Series Sonic conductance C [dm /(s bar)] Type of actuation Voltage position single type Passage: 4/ 5/ (A/B EA/EB) Electrical entry

More information

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types

Air Cylinder. New. New RoHS. 6 types. Series CJ2. are. added to the mounting types. 4 types 7 types ir Cylinder Ø 6, Ø 1, Ø New RoS Double foot ead flange Double-side bossed added to the mounting types. 4 types 7 types New or Ø 6, 3 types are 6 types Double foot Double-side bossed ead flange ead cover

More information

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added.

Air Cylinder. New RoHS. Series CJ2. are. added to the mounting types. Improved amount of mounting freedom Head cover with boss is added. ir Cylinder ø1, ø16 Double foot Double-side bossed added to the mounting types. 4 types 7 types Improved amount of mounting freedom Head cover with boss is added. Head flange are Double foot Double-side

More information

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover.

1.7 kg. % lighter. 1.9 kg. Air Cylinder. Weight MB1. Reduced weight by changing the shape of the rod cover and head cover. Air Cylinder 1 Series ø32, ø40, ø50, ø63, ø80, ø100, ø125 RoHS 10 (ø50-100 stroke) % lighter Current model 1.9 kg 1 Series 1.7 kg J 1 Reduced weight by changing the shape of the rod cover and head cover.

More information

5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in. Flow characteristics (1) 1 4/2 (P A/B) 4/2 5/3 (A/B R1/R2)

5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in. Flow characteristics (1) 1 4/2 (P A/B) 4/2 5/3 (A/B R1/R2) For details about certified products conforming to international standards, visit us at www.smcworld.com. 5 Port Pilot Operated Solenoid Valve Metal Seal, Plug-in/Non Plug-in Model 2 position 3 position

More information

CAT.ES20-53 E. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E Dual-Rod Cylinder Series New: Dual-Rod Cylinder with Air Cushion Compact Type Series J Dual-Rod Cylinder with guide function for pick-and-place applications Series! Twice the thrust Non-rotating

More information

How to Order M9BW. Action. Double acting Single acting. Load voltage Electrical entry direction M9NWV M9NW 12 V 5 V, M9BWV M9BW 12 V 12 V

How to Order M9BW. Action. Double acting Single acting. Load voltage Electrical entry direction M9NWV M9NW 12 V 5 V, M9BWV M9BW 12 V 12 V Angular Type Air Gripper/Standard Type 2 Series ø, ø1, ø20, ø25 How to Order Angular type air gripper 2 20 Bore size mm 1 1 mm 20 20 mm 25 25 mm D S Action D Double acting Single acting M9BW Made to Order

More information

Heavy Duty Stopper Cylinder

Heavy Duty Stopper Cylinder Heavy Duty Stopper Cylinder Series ø, ø32 To stop pallets gently Stopper cylinder with built-in shock absorber Amount of energy absorption can be adjusted to suit the load. Stops the workpiece gently with

More information

(Standard) 100 VAC, 50/60 Hz 200 VAC, 50/60 Hz 24 VDC

(Standard) 100 VAC, 50/60 Hz 200 VAC, 50/60 Hz 24 VDC 5 Port Pilot Operated Solenoid Valve Metal Seal Series VZS Series Variations Plug-in Type Base Mounted Type (With sub-plate) Non Plug-in Type Base Mounted Type (With sub-plate) Series Sonic conductance

More information

Series RSH/RS1H. To stop pallets gently. Stopper cylinder with built-in shock absorber. Heavy Duty Stopper Cylinder. ø20, ø32 ø50, ø63, ø80

Series RSH/RS1H. To stop pallets gently. Stopper cylinder with built-in shock absorber. Heavy Duty Stopper Cylinder. ø20, ø32 ø50, ø63, ø80 CAT.ES-118 B Heavy Duty Stopper Cylinder Series RSH/RS1H ø, ø ø, ø, ø To stop pallets gently Stopper cylinder with built-in shock absorber Heavy Duty Stopper Cylinder Series RSH/RS1H ø, ø ø, ø, ø To stop

More information

Angular Style Air Gripper

Angular Style Air Gripper Angular Style Air Gripper Series /A/M 15 Angular style air gripper Series /A/M - Auto switch is attachable. 8 mm x 0 mm x mm g Body option (Only for A-) Side piping Port Port A- Short body. 1 mm x 0 mm

More information

Compact Cylinder/Plate type

Compact Cylinder/Plate type Compact Cylinder/Plate type Series :,,, Width: Reduced by up to % (compared with SMC series) Total length: Reduced by up to % Volume: Reduced by up to 1% Weight: Reduced by up to % (compared with SMC series

More information

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g.

240% 19% reduced. Compact Slide. MXH Series. Improved by up to. With new high rigidity linear guide. 369g. ø6, ø10, ø16, ø g. Compact Slide Series ø, ø, ø, ø RoHS Allowable moment MXS Improved by up to MXQ MXQ 2% MXF MXW MXJ MXP MXY With new high rigidity linear guide MTS Allowable moment improvement illustrated below Allowable

More information

LZB/LZC. Series LZB LZC. Electric Cylinder. Series. Series LJ1 LG1 LTF LC1 LC7 LC8 LXF LXP LXS LC3F2 E-MY LZB LZC

LZB/LZC. Series LZB LZC. Electric Cylinder. Series. Series LJ1 LG1 LTF LC1 LC7 LC8 LXF LXP LXS LC3F2 E-MY LZB LZC P097-P0992-E.qxd..1 11:3 AM Page 97 Electric Cylinder Series LZB/LZC. r e d n yli e k i l d te It can LJ1 c r i a an LG1 LTF ra e p o be LC1 LC7 LC8 LXF Series LXP LZB LXS LC6첸 LZ첸 LC3F2 X첸 Series D-첸

More information

Compact Guide Cylinder

Compact Guide Cylinder Compact Guide Cylinder Series ø, ø, ø, ø, ø, ø, ø, ø, ø, ø ir cylinder with guide integrated that has achieved anti-lateral load and high non-rotating accuracy. Space-saving cylinder. Suitable as stoppers

More information

Series VP3145/3165/3185

Series VP3145/3165/3185 Large flow capacity, small exhaust resistance (Refer to Flow Characteristic table.) Easy conversion to N.C. or N.O. N.C. N.C. X (P) N.O. N.O. X (P) Series VP 3 port Function plate makes it possible to

More information

Series VKF300 VV061 V100 S070 VQD VKF VK VT VS

Series VKF300 VV061 V100 S070 VQD VKF VK VT VS Rubber Seal 3 Port Solenoid Valve Series VKF300 Direct Operated Poppet Type Compact yet provides a large flow capacity Body width 18 mm Various manifold piping directions Output port: Manifold set-up allowing

More information

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New:

CAT.ES20-53 E -UK. Dual-Rod Cylinder. Series CXS. CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ. New: CAT.ES-3 E -UK Dual-Rod Cylinder Series CXS New: CXS Dual-Rod Cylinder with Air Cushion Compact Type Series CXSJ Dual-Rod Cylinder with guide functio for pick-and-place applications Series CXS! Twice the

More information

Series MGPS. Compact Guide Cylinder: ø50, ø80 MGP S Z73. How to Order. Applicable auto switches. Compact Guide Cylinder.

Series MGPS. Compact Guide Cylinder: ø50, ø80 MGP S Z73. How to Order. Applicable auto switches. Compact Guide Cylinder. Compact Guide Cylinder: Series S ø, Compact Guide Cylinder Compact guide cylinder Heavy duty guide rod type S Z73 mm mm How to Order Number of auto switches Nil S 2 pcs. 1 pc. Auto switch type Nil Without

More information

22mm Space required between the bottom of the cylinder body and your equipment is reduced.

22mm Space required between the bottom of the cylinder body and your equipment is reduced. Compact Guide Cylinder ø2,,, ø2,,, ø0, ø63,, ø0 With air cushion Water resistant cylinder are now available. New Up to 7% Weight reduced! New Weight reduced by up to 7% with a shorter guide rod and thinner

More information

Pilot Operated 2 Port Solenoid Valve for Dry Air

Pilot Operated 2 Port Solenoid Valve for Dry Air Pilot Operated Port Solenoid Valve for Dry ir VQ0/30 Series Compact and lightweight with large flow capacity [Option] VQ0 Weight (g) 46 80 C [dm 3 /(s bar)].5 (C8) 3.0 (C) Series VQ0 Series VCH VDW SX0

More information

Elliptical design for space-savings

Elliptical design for space-savings Plate Cylinder Series,,,, By adopting an elliptical piston design, a slim, square shaped body has been achieved, resulting in a space-saving cylinder with unrestricted mounting directions. Elliptical design

More information

How to Order. Lead wire length Nil L Z M9N L. Type of auto switch for detecting rotation. Nil Without auto switch. Applicable Auto Switch

How to Order. Lead wire length Nil L Z M9N L. Type of auto switch for detecting rotation. Nil Without auto switch. Applicable Auto Switch Indicator light Indicator light Rotary Gripper Series MRHQ Size:, 1,, 25 How to Order Lead wire length Nil L Z.5 m 3 m 5 m MRH Q D 9 S M9NV L M9N L Q Rotary gripper Gripper Parallel type: 2 fingers D S

More information

Rotary Actuated Air Gripper

Rotary Actuated Air Gripper Rotary ctuated ir Gripper MHR, MDHR/MHR3, MDHR3 -finger type: Size, 15,, 3/ 3-finger type: Size, 15 High Precision - Repeatability ±.1 mm Parallel opening and closing mechanism utilizing a cross roller

More information

0.35 W (Without light)

0.35 W (Without light) Modular Connection Type Residual Pressure Relief 3 Port Solenoid Valve For connecting to F.R.L. units C25- C30- C40- FORMTION RoHS VP500 VP700 llows for space saving and reduced piping labor. Power consumption:

More information

Pilot Operated 2 Port Solenoid Valve for Dry Air

Pilot Operated 2 Port Solenoid Valve for Dry Air Pilot Operated Port Solenoid Valve for Dry Air Series VQ0/30 Compact and lightweight with large flow capacity VQ0 Mass (g) 46 80 C [dm 3 /(s bar)].5 (C8) 3.0 (C) Series VQ0 High frequency operation possible

More information

/ ø6, ø10, ø16, ø20 A table cylinder suitable for short pitch mounting

/ ø6, ø10, ø16, ø20 A table cylinder suitable for short pitch mounting roduces a table cylinder non-rotating accuracy MXH / ø, ø, ø1, ø A table cylinder suitable for short pitch mounting Application example Auto switches offer numerous variations Reed switches, solid state

More information

Body width of 10mm, Nl/min (49.08) 2W (Standard) Nl/min (78.52) 4W (U type: Large flow) Vacuum applications possible (up to 100kPa) 3 S.

Body width of 10mm, Nl/min (49.08) 2W (Standard) Nl/min (78.52) 4W (U type: Large flow) Vacuum applications possible (up to 100kPa) 3 S. High speed coil with stable response times ON: 4ms, OFF: 2ms, Dispersion accuracy: ±1ms (With light and surge voltage suppressor at a supply pressure of 0.5MPa, subject to clean, dry air) 4 Port Direct

More information

Power Valve: Regulator Valve. Specifications. Model VEX Operation type Fluid Max. operating pressure Set pressure Air operated.

Power Valve: Regulator Valve. Specifications. Model VEX Operation type Fluid Max. operating pressure Set pressure Air operated. Power Valve: Regulator Valve Series Large capacity relief regulator Rapid tank internal pressure setting, air blow, constant pressure supply and driving, balance and driving, steps directional control

More information

Vacuum applications possible (up to 100kPa) Base mounted. Cylinder bore size (mm) Series CM2. Pressure: 0.5MPa Load ratio: 50% Cylinder stroke: 300mm

Vacuum applications possible (up to 100kPa) Base mounted. Cylinder bore size (mm) Series CM2. Pressure: 0.5MPa Load ratio: 50% Cylinder stroke: 300mm 4 Port Direct Operated Poppet Solenoid Valve Series D1000 High speed coil with stable response times ON: 4ms, OFF: 2ms, Dispersion accuracy: ±1ms (With light and surge voltage suppressor at a supply pressure

More information

Grommet (G) (Standard) 100 VAC, 50/60 Hz 200 VAC, 50/60 Hz 24 VDC

Grommet (G) (Standard) 100 VAC, 50/60 Hz 200 VAC, 50/60 Hz 24 VDC 5 Port Pilot Operated Solenoid Valve Metal Seal Series S Series Variations Body Ported Base Mounted Series S000 S000 S000 S000 S000 S4000 S5000 Sonic conductance C [dm /s bar)] 4/ 5/(A/B R/R) Single Double.8.4

More information

Power Valve: Economy Valve. Standard Specifications. Model VEX55-04

Power Valve: Economy Valve. Standard Specifications. Model VEX55-04 Three functions (pressure regulator, switching valve, and speed controller) are provided by a single valve. The conventional valve combination circuit has been condensed into a single valve. A large capacity

More information

3 Port Solenoid Valve Pilot Operated Poppet Type. External pilot

3 Port Solenoid Valve Pilot Operated Poppet Type. External pilot 3 Port Solenoid Valve Pilot Operated Poppet Type Series VG342 Rubber Seal [Option] Low power consumption 4.8 W DC (Standard type) 2 W DC (Energy-saving type) No lubrication required Possible to use in

More information

Air Gripper (2 Finger) (3 Finger)

Air Gripper (2 Finger) (3 Finger) Rotary Actuated Air Gripper ( Finger) (3 Finger) MHR/MDHR, MHR3/MDHR3 High Precision - Repeatability ±0.01mm Parallel opening and closing mechanism utilizing a cross roller guide produces smooth operation

More information

Series VP3145/3165/3185

Series VP3145/3165/3185 Large Size 3 Port Solenoid Valve Series VP345/365/385 Rubber Seal Large flow capacity, small exhaust resistance (Refer to Flow Characteristic table.) Easy conversion to N.C. or N.O. Function plate makes

More information

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil

How to Order D 30 D M9BW. Made to Order Specifications Bore size Number of. Rod end configuration Cylinder stroke (mm) Nil With auto switch RSG RSDG With auto switch (uilt-in magnet) uilt-in Magnet Cylinder Model If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the

More information

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP

CAT.ES C. Compact Guide Cylinder. SeriesMGP. ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100. New end lock type introduced to Series MGP CT.S-7 C Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 New end lock type introduced to Series . Top mount Compact Guide Cylinder Series ø, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Four mounting types

More information

MHR3/MDHR3 Series. Rotary Actuated Air Gripper/3-Finger Type. Size: 10, 15 MDHR 3 10 R M9N S. How to Order. Without auto switch

MHR3/MDHR3 Series. Rotary Actuated Air Gripper/3-Finger Type. Size: 10, 15 MDHR 3 10 R M9N S. How to Order. Without auto switch Rotary ctuated ir Gripper/3-Finger Type MHR3/MDHR3 Series Size:, 1 How to Order Without auto switch MHR 3 R Connecting port R ody side R: ody side Port With auto switch (uilt-in magnet) MDHR 3 R M9N S

More information

Mini Free Mount Cylinder

Mini Free Mount Cylinder Mini Free Mount Cylinder Series ø, ø, ø, ø, ø, ø1, ø Series 1 ction Stroke 1 2 0 0 0 Clean uto switch series None Rod end Male threaded Without thread Solid state switch D-F D-M9 D-M9 W Female threaded

More information

Manual override. Non-locking push type (Tool required) Nil: B: Locking type (Tool required) C: Locking type (Manual) Electrical entry

Manual override. Non-locking push type (Tool required) Nil: B: Locking type (Tool required) C: Locking type (Manual) Electrical entry Plug-in nit Series 0 1 2 3 4 Series Type of actuation Metal Rubber 2 position single 3 position closed 3 position pressure Manifold Option How to Order Valves VQ 1 1 1 0 Y 5 LO Body type 1 0 1 Seal Metal

More information

Rotary Actuator Vane Style

Rotary Actuator Vane Style Rotary Actuator Vane Style Series /:,, 2, Rotation angles:, 18, 27 Up to 27 is possible for the entire series Through the adoption of specially designed seals and stoppers, a swing angle of 27 has been

More information

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder.

22 mm Space required between the bottom of the cylinder body and your equipment is reduced. 24% Up to. Compact Guide Cylinder. Compact Guide Cylinder Series ø2,,, ø2,,, ø, ø63,, ø0 Up to Weight reduced by up to 24% with a shorter guide rod and thinner plate 24% Weight reduced! 3 types of bearing can be selected. Slide bearing

More information

Series CRA1. Rotary Actuator. Rack Pinion Style/Size: 30, 50, 63, 80, 100 CRB CRBU CRJ CRA1 CRQ MRQ MSQ MSU

Series CRA1. Rotary Actuator. Rack Pinion Style/Size: 30, 50, 63, 80, 100 CRB CRBU CRJ CRA1 CRQ MRQ MSQ MSU Rotary Actuator Series Rack Pinion Style/:, 0,,, Series Variations Standard s with cushion or with solenoid valve available. (Only sizes 0 are available.) Angle adjustement is possible. Fine angle adjuster

More information

Power Valve: Regulator Valve. Specifications. Model VEX Operation type Fluid Max. operating pressure Set pressure Air operated.

Power Valve: Regulator Valve. Specifications. Model VEX Operation type Fluid Max. operating pressure Set pressure Air operated. Power Valve: Regulator Valve Series 1 Large capacity relief regulator Rapid tank internal pressure setting, air blow, constant pressure supply and driving, balance and driving, steps directional control

More information

Parallel Style Air Gripper: Wide Type

Parallel Style Air Gripper: Wide Type Parallel Style Air Gripper: Wide Type Series MHL Built-in dust-protection mechanism A scraper with a dust lip is adopted for all rod rotating parts. A large amount of gripping force is provided through

More information

Compact Guide Cylinder

Compact Guide Cylinder Compact Guide Cylinder Series ø2, ø, ø, ø2, ø, ø, ø, ø, ø, ø0 Series standard type and series high precision ball bushing bearing type (except with end lock) products have been remodeled for a lightweight

More information

Vacuum Equipment. Application. Series

Vacuum Equipment. Application. Series Equipment Series Application Page ejector In-line vacuum ejector Multistage ejector ejector with check valve Pad with check valve ejector for water soluble coolant removal ZH ZU ZL1/2 (Special order product)

More information