Multi-Power Cylinders

Transcription

1 ulti-power ylinders vailable in series ore sizes /" thru " trokes /8" thru " Original eries (shown right) ores -/8" thru " trokes /" thru " orces to,000 lbs. ( tons!) Pancake eries (see pages. to.7) ores /" thru " trokes /8" thru -/" orces to 7,86 lbs quare eries (see pages.8 to.) ores /" thru " trokes /8" thru -/" orces to 870 lbs. ongstroke eries (see pages. to.8) ores " thru " trokes /" thru " orces to 7,86 lbs uralon od earings xcel oad apacity (psi) achine esign 97/7 earing eference Issue Porous ronze...,00 Porous iron... 8,000 Phenolics... 6,000 Nylon..., einforced elfon...,00 * fabric... 60,000 Polycarbonate...,000 cetal...,000 arbon-graphite riction Properties lip- oefficient stick teel-on-steel... Yes ronze-on-steel.... Yes intered ronze-on-steel with mineral oil.... No ronze-on-steel with mineral oil....6 No opper lead alloy-on-steel. Yes cetal-on-steel....0 No Nylon-on-steel.... Yes uralon-on-steel No Printed with permission by exnord orp. eatures & enefits ore force from available shop air liminates hydraulics stays clean ultiple pistons on the power stroke aves mounting space ( to 7%) ingle piston on the retract stroke aves air ( to 7%) uilding block design ow cost Quick delivery pecials Wide range of models, sizes and options... dapts to your application requirements orrosion resistant construction ong life clean appearance Internally lubricated dynamic seals mooth operation and long product life uralon rod bearings ee chart above extended product life ard anodized I cylinder tubing ore cycles less wear Year warranty xtended buyer protection

2 et forces up to,000 pounds from shop air pressure! ow it works xhaust ir tmospheric ir xhaust tmospheric ir xhaust tmospheric ir xhaust hop ir upply to xtend Port abco-ir attaches multiple pistons to a common shaft and provides internal air passages through the shaft to all pistons. hus, when shop air pressure is applied to the extend port, all pistons are pressurized simultaneously enabling tremendous thrust forces to be obtained. ee the handy sizing guide below for available force multiplying factors (column otal ffective Piston rea) and maximum operating pressures for various cylinder bore sizes. hop ir upply to etract Port Piston # tmospheric ir rawn In Piston # tmospheric ir rawn In Piston # Internal ir Passages tmospheric ir rawn In Piston # xhaust ir izing xample P X X X Piston rea is 0. sq. in. orce = Pressure x rea If upply ir Pressure is 00 psi, then orce = 00 psi x 0. or orce = 00 lbs -- ore Inches tages (Number of Pistons) otal ffective Piston rea-quare Inches quivalent ore of a ingle Piston ylinder orce@ 60 psi izing uide od iameter, in. ingle tage etract Piston rea, sq. in / / / od rea, sq. in. ase Weight, lb. ero troke Weight Per inch, lb. of troke ax. Operating Pressure Notes reas given are for ultiple tage xtend - ingle tage etract with a ingle od. or ingle tage xtend - ultiple tage etract and any ouble od odels, deduct the rod area shown. reas given are for tandard ingle tage etract. or ingle tage xtend with a single rod, add the rod area shown. atings tandard Units uralon rod bushing. (see page. for table of physical properties) emale rod end with wrench fl ats Internally lubricated una-n O-ring piston and rod seals. irline lubrication recommended edia ir ax. operating pressure ee chart in. pressure recommended psi mbient & media temp to +0 Prelubrication.... agnalube rease.

3 ulti-power ylinders asic onstruction ultiple tage xtend with ingle tage etract ingle etract eturn troke ultiple xtend Power troke NP Port NP Port ultiple tage etract with ingle tage xtend ultiple etract Power troke NP Port ingle xtend eturn troke NP Port Quick eference to omponents No. escription ylinder tube seal tmospheric vent Piston rod ir passage between stages enter stud, high tensile, plated 6 tainless steel tie rods and plated steel nuts 7 Piston stop 8 ap nd Plug, aluminum, black anodized 9 Nut, plated steel 0 Piston od Pilot Washer locates piston to maintain precise concentricity ap end head, aluminum, black anodized ylinder tube, aluminum affl e, aluminum affl e seal, una-n O'ings, to + 0 Piston seal, internally lubricated O'ing 6 Piston rod seal, internally lubricated O'ing 7 enter shaft seal, internally lubricated O'ing 8 Piston, aluminum 9 Piston air slot, note direction of air fl ow 0 od end head, aluminum, black anodized Piston rod bushing, anodized aluminum housing with efl on lined uralon insert ylinder O is clear anodized aluminum for corrosion resistance and an attractive appearance. he ore I is ard nodized ard anodizing is an electrochemical process which provides a very dense surface of aluminum oxide that actually impregnates the base aluminum. It forms an extremely hard (60 c) surface with a low coeffi cient of friction. ardness, corrosion resistance and wear resistance exceeds that of chrome plated steel. n xtra ong od earing provides long and rigid support for the piston rod. he bearing material is uralon on all bore sizes. ee page. for a chart comparing the exceptional physical properties of uralon to other, less durable, bearing materials. he Piston od is ard hrome Plated tainless teel. urface finish is or better.he standard rod end is fine female thread tapped and has long wrench flats. Piston onstruction he piston is aluminum for light weight. he piston rod pilot end and a pilot washer enable bolting the assembly securely while maintaining precise concentricity for smooth cylinder performance. ynamic eals Internally lubricated O'ings are compounded to provide extra long wear, lower breakaway (starting) and running friction, and smoother operation. In tests, cylinders with these seals have extended cycle life to times beyond cylinders with standard una-n seals

4 odel Number ode P X X X ow to Order ow to Order. pecify eries and ore. pecify troke in Inches and ractions. Note standard strokes listed above. trokes not listed are available to " maximum at a nominal increase in delivery time and cost.. pecify stages extend. pecify stages retract. pecify ounting 6. pecify Options xample P X X X ulti-power eries, " bore, " stroke, tage xtend, tage etract, ront ace (abco Pattern) ount, ale od hread. -- P eries & ore -/8" -/8" -/" " " " 6" 8" 0" " tandard trokes /" " -/" " -/" " " " 6" Optional trokes any other stroke 0" thru " tages xtend tages etract X X X X X X tandard available combinations are listed above. ee page.7 for ultiple xtendultiple etract Options. Note: pplicable only to -/8" thru 8" bores. ores ounting -/8" ront ace abco Pattern... thru ront ace NP () Pattern... 6" ear ace abco Pattern... ear ace NP () Pattern... oot... levis ount NP (P) imensions for single stage retract only Ports in-line with slot...p Ports 90 to slot... xtended ie ods (ee page.6 for non-standard lengths.) od end only...w ap end only... W od and ap nds...w ront ace NP () Pattern... 8" ear ace NP () Pattern... 0" xtended ie ods " od end only...w ap end only... W od and ap nds...w OPION escription pecify ee Page " od thread 8" bore only -. ouble od -.8 Nonrotating ingle od -N.8 Nonrotating ouble od -N.8 ale od hread.7 ingle od - ouble od, od nd - ouble od, ap nd - ouble od, oth nds - Viton eals (- to +00 ) -V.8 hock & peed ontrol using -. ydraulics, -/" " bores ubber umpers.9 od nd - ap nd - oth nds - djustable xtend troke -.9 6" troke maximum. ull stroke adjustment is standard. /" NP Ports in eads (-/", ", ", " & 6" ores only).0 od nd ead - ap nd ead - oth eads - / NP Ports in eads -P.0 (8", 0" & " ores only) xtend Port ushing.0 /8 NP (-/" 6" ores) -8 / NP (-/" 6" ores) - / NP (" " ores) - igh low Vents -.0 Port Positions. &.6 ll Ports Position # tandard Position # -P Position # -P Position # -P od nd Position # tandard Position # -P Position # -P Position # -P ap nd Position # tandard Position # -P Position # -P Position # -P tmospheric Vent or Ported affl e Port Position # tandard Position # -P Position # -P Position # -P ny port or vent not specifi ed will be in Position # as shown on page. &.6 agnetic Piston -. for reed switches and lectronic ensors (Order ensors separately) Note: dditional cylinder length required for Nonrotating ods see page.8; for Option - see page.; for / NP Ports Option see page.0; for Option - see page..

5 ulti-power ylinders -/8", -/8", -/", ", ", ", & 6" ores ear ace ount; ap nd ectangular lange abco mounting pattern U Q O hd ront ace ount; od nd ectangular lange abco mounting pattern Q N ex Nut Places ap nd N ex Nut Places od nd O hd U ear ace ount; ap nd ectangular lange NP () mounting pattern U Q O hd ront ace ount; od nd ectangular lange NP () mounting pattern Q N ex Nut Places ap nd N ex Nut Places od nd O -/8" = NP -/" O " = NP -/" O hd imensions (inches) Note: he imension Y is for standard models: ultiple extend/single retract and ingle extend/multiple retract. Optional ultiple extend/ multiple retract models require additional cylinder length (see page.7). he following options also require additional cylinder length. ee the respective option information pages for details. -N, N (pg.8), - (pg.), -, -, - (pg.0), - (pg.). Note: imension for 8" ore only, specify Option for "- od hread U O -/8" = NP -/" O " = NP -/" or single stage retract only levis ount (NP P imensions) P - Ports in-line with slot - Ports 90 to slot U aterial: ray Iron asting, lack Oxide inish Pin ross Pin and lips Included abco -/8" = NP -/" abco -/8" = NP -/" abco " = NP -/" W W N ex Nut Places oth nds -/" thru 6" ores; od end only -/8" & -/8" ores ore -/8 -/8 -/ = (No. stages x stroke) + y y ( stage) y ( stage) y ( stage) ± /6-x.6 /8-x.6 /-0x.7 /-0x.7 /-0x.7 /-6x. /-6x. -x /-x.7 /-x.7 7/6 / /8 /8 7/8 -/ -/ -/ ± N 7/6 7/6 9/6 9/6 / / / / -/8 -/8 P Q NP /8 /8 / / / / / / / /

6 ounting tyles with imensions 8", 0", and " ores -/8", -/8", -/", ", ", ", & 6" ores ront ace ount; od nd quare lange NP () mounting pattern oot ount Q od nd View Q P O X. N ex Nut Places oth nds X W O hd ear ace ount; ap nd quare lange NP () mounting pattern N ex Nut 8 Places ap nd U W W W xtended ie od ount, od nd Only ap nd Only od & ap nds Q O hd U ap lats Q ap nd View o Order xtended ie od ount pecify uffi x od nd only W ap nd only W od & ap nds W W V V W N ex Nut Places oth nds odels If a non-standard extension is required, specify by adding the required length to the suffi x. e.g. If W length required is.", pecify W." N ex Nut 8 Places od nd W W W Q xtended ie od ount, od nd Only ap nd Only od & ap nds W W W W O hd V O hd N ex Nut 8 Places oth nds ore -/8 -/8 -/ U V W X O /-0 /-0 /8-6 /8-6 /- /- /- /- /-0 / O W W W

7 ulti-power ylinders ultiple tages xtend & ultiple tages etract (Not available on 0" and " bores) When required return forces (xtend or etract) are greater than the standard single piston can provide, multiple stages (pistons) can be pressurized. his is accomplished by replacing one or more of the standard baffl es with a ported baffl e as shown in the illustration. When these thicker baffl es are used, the overall length ( imension ) increases. ee the chart below for port size and dimension details. ee pages. for imension dd to imension ore Port for each Ported affle -/8" /8 NP " -/8" /8 NP " -/" / NP " " / NP " " / NP " " / NP " 6" / NP " 8" / NP " xample: odel PXXX Ports externally connected for ultiple etract Ported affl e NP Port No. of otal vailable Ported No. of ombinations affles tages X X X X X X X X X ube seals + [ ee hart ] tmospheric Vent ultiple xtend Port tandard affl e Notes: When any of these combinations are ordered, the proper number of ported baffl es are included. s standard, the largest number of stages are internally connected. On models with the same number of extend and retract stages, the extend stages are internally connected. pplications that may dictate the use of Ported affles lean rooms, Vacuum hambers, Wash own reas, Under iquid, irty or orrosive nvironments Increase ycle peeds elective orce pplication ilters can be installed in the ports of stages not requiring pressurization, or they can be plumbed to a common fi lter or point outside the critical environment. he ports have higher air fl ow capacity than the vents in the standard baffl e. With control circuitry, the number of stages that are pressurized (thus the amount of force being applied) at any given time can be selected and varied. onsult engineering with application details. ale od hread ingle od ouble od, od nd Only ouble od, ap nd Only ouble od, od & ap nds od octite Option tud No elief No Weakness or bores -/8" thru 8", a high strength stud is threaded into the standard female rod end and retained with octite. his method eliminates the small diameter thread relief area normally required when machining male threads. his provides a much stronger hread rod end which can be repaired, rather than replacing the complete rod, should the thread be damaged. or 0" and ", the thread is machined integral with the rod. O -/8" /6 x.6 -/8" /8 x.88 -/" /0 x " /0 x " /0 x " /6 x 6" /6 x 8" standard x 8" optional x 0" - / x. " - / x. Note: ale rod callout must be preceeded by

8 Option pecifications ouble od Option - + stroke ee page. for tandard piston rod and rod bushing on both ends of the cylinder. or 8" bore only, when - is dimension. specifi ed, " threads will be applied ypical for at both ends. bores and mounting styles. Note: 0" & " ores for Position Indication Only od hread /8-6 x /8 eep Use when attachment to both ends of the cylinder is required, or to indicate piston position. lso see Option on page.. Viton eals Option -V Use for elevated temperatures ( to + 00 ) or compatibility with exotic media. onsult engineering for compatibility information. Nonrotating od Option -N stainless steel hex rod and a hex broached bushing of 660 bearing bronze replaces the standard round rod and bushing. ported baffl e is used so the piston assembly can be retracted by the next piston back from the rod end. he normal rod head port becomes an atmospheric vent. he tolerance on rotation is ±. he hex rod design does allow for some torque loading on the shaft. V V owever, torque loads that induce side loading should be minimized for best overall life and performance. No. of otal vailable Ported No. of ombinations affles tages X X X X X X Note: Not applicable to 0" and " bores ex od No rod seal ee page. for imension tmospheric Vent for all extend/retract combinations Ported affl e etract Port + [ ee hart ] ex rod fl ats andom otation relative to ounting Pattern + [ee hart] dd to imension / NP Ports / NP Ports etract for each t'd Ports ( or ) (P) ore Port Ported affle V V max V V max V V max -/8" /8 NP " ". -/8" /8 NP ".6". -/" / NP ".7" " / NP ".7" " / NP " " " / NP " " " / NP " " " / NP " " " / NP ".00" " / NP ".00" Nonrotating ouble od Option -N combination of the Options N and as shown above. he rod end rod is ex and the cap end rod is round. he ported baffl es are included and the imension adjustments shown for Option N must be made. xtended piston areas must also be reduced by the rod area. --.8

9 djustable extend stroke Option - or strokes through 6" ull stroke adjustment is standard. Note! o maintain operator safety features of this option, it is NO available with mounting styles: W and W. Use caution when mounting to avoid creating pinch points. Not available with mounting styles P and. Not available for 0" & " bores ial--troke provides a rugged and precision adjustment of the extend stroke of the cylinder. he stop tube, adjustment nut with skirt, and minimum clearances combine to eliminate pinch points, thus providing operator safety. Note! Use caution when mounting to avoid creating pinch points with other parts of your machine design. he stop tube is black anodized aluminum, the adjustment nut is blackened steel with a black anodized aluminum skirt, and the nut stop is red anodized aluminum; all for corrosion resistance and appearance. he adjustment nut, steel for long life, includes a lock screw with a plastic plug so that the adjustment nut can be locked in place without damaging the threads. he nut stop is mounted on the end of the adjustment rod so that the nut cannot come off. he fi ne pitch threads on the adjustment rod and nut provide precision adjustment. (ee dimension ""). djustment settings are simplifi ed by convenient scale markings applied to nut skirt and stop tube. od ushing + troke iameter ulti-power ylinders top ube djustment Nut kirt ock crew Plastic Plug Nut top djustment od with fine pitch thread (ee imension ) djustment Nut with ating ine Pitch hread ontact urfaces totally enclosed /"inimum learance when fully stroked Note: Use caution when mounting to avoid creating pinch points + ( x troke) + troke iameter troke adjustment per revolution ore -/8" -/8" -/" " " " 6" 8" ( x troke) + troke ubber umpers od nd only ap nd only oth od & ap nds ubber umpers Option rubber doughnut is bonded to the cylinder head to act as the piston stop and absorb the impact of the piston. his reduces noise and absorbs energy, thus reducing damage to the cylinder and tooling due to pounding. he amount of rubber that extends beyond the normal piston stop is designed to compress and allow full stroke of the cylinder at 60 to 80 psi. If your application uses lower pressure or has high energy, consult engineering with application details so that rubber mass can be adjusted to meet your specifi c requirements. ecause of the temperature limitations of the adhesives involved (- to + ), rubber bumpers are available in cylinders with standard internally lubricated una-n seals only. Use where noise reduction and impact absorption is desired. Note! On applications such as punching, shearing, setting blind rivets, etc., where high forces are built up and then released VY quickly, the proper method of catching this type of load is to adjust the cylinder piston and the tooling so that at the point of breakthrough the piston is very close to the bumper. his reduces the dynamic load that the piston and bumper are required to absorb..9 --

10 Option pecifications xtend Port ushing Option /8 NP (-/" 6" bores) -8 / NP (-/" 6" bores) - / NP (" " bores) - tandard port plugged xtend Port xtended ap nd Plug with emale NP Port he cap end plug is replaced with an extended plug of black anodized aluminum with a female NP port. he standard cap end port is plugged. Use for plumbing convenience, or when higher air fl ows are required for higher cycle speeds. ore -/ Wrench lats imensions (inches) vailability / NP Ports in eads Option -/", ", ", ", & 6" ores only od nd ead - ap nd ead - oth eads - / NP Ports in O eads 8", 0" & " ores only -P Q NP Q NP or -/" thru 6" bores, thicker heads (to accept / NP ports) replace the standard heads. ecause of the thicker heads, there is an increase in imension and a reduction of the rod extension as charted below. With this construction, an O'ing replaces the fi ber gasket cylinder tube seal. or 8", 0" and " bores, / NP ports are applied to standard heads. Use when higher cycle speeds are required. O'ing ube eal oth nds Option P dd to Q / / / / Q / / / / -/ & " ore 0.7, & 6" ore , 0 & " ore + [ee chart] -/ & " ore 0.7, & 6" ore , 0 & " ore - + troke Option - only ee pages. &.6 for imension -/, & " ore & 6" ore , 0 & " ore - -/, & " ore & 6" ore , 0 & " ore igh low Vents Option - he atmospheric vent in the baffl e is cut larger to provide less resistance to the air fl ow. Use when higher cycle speeds are required

11 ulti-power ylinders peed & hock ontrol Using ydraulics Option - vailable in -/" through " ore emperature range: to + 0 vailable with Viton seals dd -V emperature range: to +00 Note!!! ll -tage Units -/" thru 0" ores are rated at 0 psi maximum air input! " ore, -tage is rated at 0 psi max. " ore, -tage is rated at 00 psi max. eries P, ore -/", ", " " 6" 8" 0", " ore, -/", ", ee chart dd to Pg. &.6 0" 0." 0" 0." 0.00" dd to Pg. 0" pplication ips When ulti-power cylinders are applied to applications such as punching or shearing, high inertial and impact forces are often encountered. o capture these potentially destructive forces, and prevent possible damage to tooling and cylinder specify Option. he seals on the piston, piston rod and tube are increased in the single return stage (retract or extend) and fl uid is used to control speed and shock. luid from an air-over-oil tank is used for the return media. his fl uid passes through a resistance, such as a fl ow control, which provides speed control of the cylinder. When the material shears and the cylinder tries to complete its stroke, the non-compressible fl uid resists rapid movement, providing shock and speed control. Note the circuits shown below. / NP Porting is available for -/", ", ", ", & 6" ores; / NP Porting is available for 0" & " ores dditional od eal, Polypak 660 ronze ushing tandard od eal, O'ing or less fl uid restriction and larger plumbing on -/" through 6" bores, see the / NP porting options,, and on page.0. lso for 0" & " bores, / NP Port Option -P is available. ee page.0. Note!! he fl uid pressure in the return stage is limited to 00 psi. his dictates that all -stage units thru 0" bore be limited to 0 psi maximum air input! " bore, stage units are limited to 0 psi; stage units are limited to 00 psi. Use when smooth, rigid, and precision speed control is required. lso with applications such as punching, shearing, setting blind rivets, etc., where high forces are built up and then released very quickly. he fl uid, being incompressible, catches these forces, both static and dynamic, dissipating them before the cylinder reaches the end of its stroke and before the piston can pound on the piston stop. dditional ube eal, O'ing dditional Piston eal, Polypak tandard Piston eal, O'ing hicker Piston he Polypak seals combine an automatic lip seal with an O'spring energizer for excellent sealing from 0 to 00 psi. wo peed & hock ontrol ingle air/oil tank with sequence, needle and shut-off valves give:. apid xtend stroke.. utomatic switch to controlled rate when resistance is met and pressure builds up.. luid catches cylinder when built-up forces are suddenly released (such as in punching applications), thus controlling the shock that could otherwise occur. lways use -hand anti tie-down systems for operator safety! onsult your local distributor for information and product delivery equence valve. utomatic return to rapid rate on etract stroke. Needle valve ir supply uffler irectional control -way air valve ingle tank air/oil unit ulti-power ylinder hut-off -way oil One peed ircuit ingle air/oil tank and fl ow control valve give hydraulic control with speed control on xtend stroke with rapid rate on etract stroke. ir supply uffl er irectional control -way air valve ingle tank air/oil unit low control ulti-power ylinder

12 Option pecifications 9-97 eries ensor & lamp for -/8" to " ores Quick isconnect ensor hown ocket ead crew 79 eries ensor with Integral lamp for " to " ore ylinders (shown prewired) 9 foot prewired sensor agnetic Piston Option - pecifies agnetic Piston (Order ensors and ensor lamps eparately) Option - consists of a magnet bonded into the piston head. When the piston magnet moves past an external sensor, the magnetic field activates the sensor without physical contact. ounting he sensor is attached to a -part clamp that attaches rigidly to a tie rod and can be positioned anywhere along the length of the cylinder for very precise signaling. wo sensor styles are used (a) the 9-97 eries for -/8" thru " bores requires a tie rod clamp, and (b) the 79 eries which accommodates the larger diameter tie rods of the " thru " bores with an integral clamp. eliability he annular piston magnet is permanently bonded into a groove in the piston. It is a polarized permanent magnet of rubber bonded barium ferrite that is very stable and is not affected by shock. Under normal usage it will remain magnetized indefi nitely. Warning xternal magnetic fi elds and/or ferrous objects may affect the strength of the piston magnet therefore affecting sensor actuation and piston position indication. abels noting this are affixed to the cylinder. Please note there is an increase in base length of the cylinder to accomodate the magnet. Using the table below add '' to imension '' on pages. &.6 () lamp tick Out & () ength dder to im. '' Pgs.. &.6 -/8" " ores ore -/8" -/8" -/" " " " 6" 8" 0" " " 6" ores Integral lamp ie od, tainless teel 8", 0", " ores emale ordsets available in,, & meter lengths WNIN his cylinder is equipped with a agnetic Piston for use with agnetically Operated ensors. Other agnetic ensitive evices hould be ept at a istance to void Inadvertent Operation. ensor & lamp Ordering uide emperature ange: 0 to + 80 ( to + 76 ) ensor ensor lamp ie od, tainless teel Piston agnet ylinder ube ylinder ead ensor Piston ylinder ube ylinder ead agnet, ubber onded arium errite Warning! o not exceed sensor ratings. Permanent damage to sensor may occur. Power supply polarity U be observed for proper operation of sensors. ee wiring diagrams included with each sensor. ensor housing rated N 6/IP67. ighted agnetic Piston Position ensors: ores -/8" " Product eed witch lectronic lectronic 9 ft. Prewired P/N Quick iscon. P/N lectrical haracteristics -0 V/V, 0. mp ax., 0 Watt ax., P N.O.,. Voltage rop ourcing, PNP, 6- V, 0.mp ax.,.0 Voltage rop inking, NPN, 6-V, 0.mp ax.,.0 Voltage rop 9-97 eries ensor ounting lamps Part Number ighted agnetic Piston Position ensors: ores " 8" eed witch lectronic lectronic V/V, mp ax., 0 Watt ax., P N.O.,.0 Voltage rop ourcing, PNP, 6- V,.0 mp ax., 0. Voltage rop inking, NPN, 6- V,.0 mp ax., 0. Voltage rop ighted agnetic Piston Position ensors: ores 0" & " eed witch lectronic lectronic V/V, mp ax., 0 Watt ax., P N.O.,.0 Voltage rop ourcing, PNP, 6- V,.0 mp ax., 0. Voltage rop inking, NPN, 6- V,.0 mp ax., 0. Voltage rop emale ordsets for 9-97 eries Quick isconnect ensors ength eter eter eter Part No emale ordsets for 79 eries Quick isconnect ensors ength eter eter Part No

13 eries Pancake ulti-power pecifications edia... ir ecommended inimum Pressure... 0 psi uralon rod bushing.... ee chart pg.. aximum Operating Pressure... 0 psi mbient & edia emperature... - to + 0 Prelubrication... agnalube - rease irline ubrication... ecommended izing Pancake ulti-power ylinders eries tages rea quivalent etract ody vailable trokes ore (Pistons) ore 60 psi rea O.. /8" /" /" /" " -/"..6 0 / / / / / rea = otal effective piston area, square inches. quivalent ore = ore required for a single piston cylinder. odels / and / odels -/8 and -/8 apped ounting oles ( at each end) 90 od ia. 90 Wrench lat olt Y ircle 0- Ports w/ ia. 'face emale od hread ixed imensions eries ore / / -/8 (im. <.) -/8 (im..) -/8 -/ #6- x. dp #8- x. dp. 'ore x.9 dp #0- x dp. 'ore x.9 dp 'ore x.6 dp 'ore x.6 dp 'ore x.6 dp 'ore x.6 dp ia x dp 0- x dp /6- x.6 dp /6- x.6 dp /8- x.7 dp /-0 x.88 dp /-0 x.88 dp /-0 x.88 dp /8-8 x.88 dp od ia. Wrench lat emale Y olt ircle od hread Note /8 NP Ports /8 (im. <.) 'ored ll /8 /8 (im..) hru oles -apped tg. oles ( at each end) /6 x. / x. 7/6 x. 7/6 x. / x. /8 x. /8 x. /8 x. 7/8 x.8 Y

14 ow to Order odel Number ode -/8 X X X eries ore /" /" -/8" -/8" " -/" " " troke ee available strokes in the sizing guide on page. Ordering xamples tages xtend odel No: eries ore x troke tages xtend tages etract X X X Pancake -ulti-power " ore, " troke, tage xtend, tage etract -/8 X / X X - Pancake -ulti-power /8" ore, /" troke, tage xtend, tage etract, ale od tages etract X X X X X X tandard available combinations are listed above. onsult factory for ultiple xtendultiple etract Options. uffix Options - ee pages. -.7 troke ollars: /8" -; /" -; /8" - hreaded Nose ount: ingle od - ouble rod, rod end - ouble rod, cap end - ouble rod, both ends - ouble od - ale rod thread: ingle rod - ouble rod, rod end - ouble rod, cap end - ouble rod, both ends - Viton seals -V xternal guide, nonrotating for load guiding - inish: Prooat -N ubber umpers: -/8 ores & arger od end - ap end - oth ends - djustable extend stroke -/8 ores & arger - levis mount: Ports in-line with slot -P Ports 90 to slot - ye mount: Ports in-line with tang -P Ports 90 to tang - agnetic piston & sensor mounting slot(s) - Order sensors separately. xtend Port ushing /8 NP for " ores and arger -8 / NP Ports for -/8" ores and arger -P odel /8 NP Ports tages extend troke /8 / / -/ /8 / / / / / Y / / olt ircle Variable imensions eries ore tages extend tages extend note note..0 note note note note 'ored hru oles () od ia. Wrench lat -/8 emale od hread Y / odels -/,, and /8 NP Ports /.00 Y 'ored hru oles () od ia. Wrench lat olt ircle emale od hread

15 hreaded Nose ount Option - vailable on /" to -/8" ore odels /" & /" ores -/8" & -/8" ore + ee page.. Pilot ia. x.06 long hread ee Page..99 hread Pilot ia. x. long ore /" /" -/8" -/8" Pancake ulti-power Pilot hread /" 0 /8" 8 " /"- Nut is included. Nut Part No hread Plated steel nose mounting brackets ust be ordered separately ore /" /" /" /" Part No W & -0 ia. / W/ W.0 ia. -0 & -0.0 ia. / W/ W. ale od hread ingle od ouble od, od nd Only ouble od, ap nd Only ouble od, oth nds Option octite od No elief No Weakness hread igh trength tud ore hread /" 8- x /" 0- x -/8" /6 x.7 -/8" /8 x.88 " /0 x -/" /0 x " /0 x " /8-8 X. levis ount Option -P & - Pivot ount Option -P & - (vailable /" thru " ore) + im. ee pages. &. -P Port locations in line with slot - Port locations 90 to slot + im. ee pages. &. -P Port locations in line with tang - Port locations 90 to tang ore /" /" -/8" -/8" " -/" " " ole Pin Pro-oat Option -N lectroless Nickel plating onsult ngineering for specifi c application requirements lectroless Nickel plating is a hard, smooth, corrosion & wear resistant coating that will often suffice for applications where stainless steel is specifi ed. he coating is a high nickel low phosphorous alloy deposited by chemical reduction without electric current that is more corrosion resistant than plated nickel. Its lasting luster provides high eye appeal. It has natural lubricity & high resistance to abrasion. tandard hardness of the coating is approximately 9 ockwell. eat treating can increase hardness to 60 ockwell

16 eries Option pecifications xternal uide, Nonrotating Option - learance in uide lock mounting holes allows for adjustment to compensate for wear + 0 -/8" through " ores -/" through " ores 90 ef. NN NN PP quare uide Pins ard hrome teel Plated ounting lock lear nodized luminum UU uide lock ard nodized luminum VV ounting oles Places UU VV ounting oles Places uperior nonrotating piston rod feature for applications such as package placement, figure stamping, and any application where anti-rotation and registration are critical as the piston is extended and retracted. mounting block is bolted to the piston rod. his block has two square pins mounted to it which in turn pass through guide blocks mounted on the sides of the cylinder. ore /" -/8" -/8" " -/" " " NN PP UU VV #6- #8- /-0 /6-8 /6-8 /6-8 /6-8 6 djustable xtend troke Option - vailable on bores -/8" and larger. ee description on page.9. + troke iameter + ( x troke) + troke iameter troke adjustment per revolution ore -/8" -/8" " -/" " " ( x troke) troke Note! Use caution when mounting to avoid creating pinch points with other parts of your machine design. ubber umpers od nd Only ap nd Only oth nds emperature ange (- to + 0 ) ubber donut or pad of rubber is bonded in place to reduce noise and absorb energy, thus reducing destruction of the cylinder and tooling due to pounding. ee complete description of benefi ts on page.9. tandard rubber mass will compress and give full stroke at 60 to 80 psi. his mass can be adjusted to meet your specifi c pressure and/or dynamic load requirements. xtend Port ushing -8 /8 NP for " ores & arger Use when higher cycle speeds are required. / NP Ports -P for -/8" ores & arger

17 eries Option pecifications agnetic Piston Option - or -/8" ore and larger Includes ovetail ounting lots Order ensors eparately ensor mounts in /" 60 ovetail single slot on longer stroke models has room to accommodate multiple sensors. horter stroke cylinders are furnished with two dovetail mounting slots when uffi x Option "" is specifi ed. -/8 -/8 -/ 7 # # # 0 0 # # # # # # 0 # # 0 0 # /8" to " stroke models have mounting slots. -/" stroke models have slot at position #. Ports are in-line for all ores, all trokes. ow Profile, olid tate, agnetic Piston Position ensors emperature ange: 0 to +80 ( to +76 ) emale ordsets for Quick isconnect ength eter eters eters Part No ensor housing rated N 6/IP67. ncased in plastic housing, dovetail style sensors are corrosion resistant. 60 wire outlet allows close mounting. Profile shown here is typical. Ordering uide ovetail tyle agnetic ensors ylinder odel eries ensor ype lectronic lectronic Prewired 9 ft. Part No Quick isconnect Part No.* Yes Yes lectrical haracteristics ourcing, PNP, -8 V, 0.0 mp ax current,.0 Voltage rop inking, NPN, -8 V, 0.0 mp ax current,.0 Voltage rop Note*: Quick disconnect style sensors are supplied with 6" pigtail. Order female cordsets separately. ouble od Option - + stroke tandard piston rod and rod bushing on both ends of the cylinder. ore /" 0. /" 0. -/8" 0. -/8" 0. " 0. -/" 0. " 0. " 0.0 Viton eals Option -V Use for elevated temperatures ( to + 00 ) or compatibility with exotic media. onsult engineering for compatibility information..7 --

18 eries Q, Q, Q quare ulti-power pecifications edia... ir ecommended inimum Pressure... 0 psi aximum Operating Pressure... 0 psi mbient & edia emperature... - to +0 Prelubrication... agnalube - rease irline ubrication... ecommended izing quare ulti-power ylinders tages rea quivalent etract eries ore (Piston) ore 60 psi rea vailable trokes /8" /" /" /" " -/" " -/" Q QW Q QW Q QW /" /8". -/ /8".79 -/ /8".8 -/ ".8 -/ rea = otal effective piston area, square inches. quivalent ore = ore required for a single piston cylinder. ow to Order odel Number ode Q W -/8 X X X - ounting Q ide ap Q ace Q ide ug od xtension ingle od odels lank for standard extension per dimension "" W - for xtension to dimension "W" ouble od odels lank "" extension both ends W "W" extension both ends ore /" 7/8" -/8" -/8" " tandard trokes Inches or strokes available ee chart above W "" extension on rod end; "W" extension on cap end W "W" extension on rod end; "" extension on cap end tages tages xtend etract X X tandard available combinations are listed above. Ordering xample: Q W -/8 X X X - - odel number code above describes quare ulti-power side lug mount cylinder with rod extension on rod end; W rod extension on cap end; -/8" bore; " stroke; stages extend; stage retract; double rod; male rod on cap end. OPION ee pages.0 -. escription pecify ale od hread ingle od - ouble od, od nd - ouble od, ap nd - ouble od, oth nds - Viton eals:- to V etric od hread - Port Positions (page.9) - xternal uide, Nonrotating - ouble od - agnetic piston and - sensor mounting slot(s) Order sensors separately. --.8

19 quare ulti-power ylinders Q eries: ide ap ounting ore availability: /", -/8", -/8", " Port Position X Port Position or W Y P (ef.) od nd ace ap nd ace N oles Q eries: ace ounting ore availability: /", -/8", -/8", " Port Position (see note) X Port Position or W Y P (ef.) (ef.) od nd ace "" apped ounting oles, each end (ee note) U ap nd ace Note: When Port Position is specified, ounting oles rotate 90 Q eries: ide ug ounting ore availability: 7/8", -/8", -/8", " Port Position X Port Position or W Y P Washer (ef.) (ef.) od nd ace ap nd ace N oles ore /" 7/8" -/8" -/8" " Variable imensions ixed imensions xdp 0-xdp /6-x.6dp /8-x.7dp /-0x.88dp ia /.9 /.9 7/6.9 /. / troke /8" /" /" /" " -/" " -/ /" & 7/8" ores -/8" ore -/8" ore " ore N 0-x. 0-x. /-0x. /6-8x N P 0-0- /8 /8 / /-0x.7dp /-0x.7dp /-0x.7dp /6-8x.7dp* U W.68 Note: -/8" & -/8" bores,/8 stroke only:.0 ia. thru,. dia. 'ore x.9 deep for #0 and /-0 x.7 deep tapped mounting holes, places each end *Note: " bore,/ stroke only:.7 ia. thru, dia. 'ore x.6 deep for /" and /6-8 x.7 deep tapped mounting holes, places each end X Y

20 eries Q ounting its ating ye racket od levis ye racket levis racket ore /" -/8" -/8" " " troke ll ll ll / / Up od nd od levis nglish etric ating ye kt levis racket P-0 P- P- P- P- ap nd ye racket runnion ount it ounting crews Included / od learance / c c ia. ore /" -/8" -/8" " aterials racket: igh strength inc die casting Pivot Pins: Precision dowel pins ounting screws:, teel, plated or black oxided it No levis racket it N I Part # P-0 P- P- P aterials racket: igh strength inc die casting ushings: Oil fi lled powdered metal Pin: 6 tainless teel lips:, Plated steel crews:, teel, plated or black oxided Pin ole I N /-0x.7 /-0x.7 /-0x /6-8x ye racket it N I Part # aterials racket: igh strength inc die casting ushings: Oil fi lled powdered metal crews:, teel, plated or black oxided. *pecial /-0 with # Phillips ead I N /-0x.7 * /-0x.7 * /-0x.7 * /-0x * /6-8x od levises P I Pin Part # -9,-9 -, - -8, -8 -, - -6, -6 aterials levis and tud: teel, black oxided Pin: 6 tainless teel lips: teel, plated PIN I P nglish 0-x. /6-x /8-x.7 /-0x.9 /-0x.6 P etric x6.mm 8x9.7mm 0x9.mm x9.9mm x.7mm.0

21 quare ulti-power ylinders lange ounting its for eries Q and QW lange tyle 7 lange tyle 8 & 9 X q. U ia. Places ia. Places eries Q q. X W eries QW U ia. Places lange ore abco ounting ole Pattern tyle ize it No. Interchange Information ole Pattern &: -/8" ore, eries,, & 7 /" 7-0 osier: -/8" ore, eries V, 8 & 9 P: -/8" ore, eries V,, & ole Pattern ompact ir: /" ore, tyle,, & ole Pattern &: -/8" ore, eries,, & 7 -/8" 7- osier: -/8" ore, eries V, 8 & 9 7 -/8 7- P: -/8" ore, eries V,, & ole Pattern ompact ir: -/8" ore, tyle,, & ole Pattern NP Ode & for -/" ore ll brands conforming to this code ole Pattern ompact ir:-/8" ore, tyle,, & ole Pattern 8 " 8- NP Ode & for " ore 9 " 9- ll brands conforming to this code ole Pattern ompact ir:" ore, tyle,, & its include lange and lange ounting crews Port Positions tandard all models. o achieve, or, rotate flange. or, specify Option - or,, or : pecify Option - and rotate fl ange QW-X-/ with 7- ore /" -/8" -/8" " " odel 0 tyle it # U. W X xternal uide, Nonrotating Option -. quare ef. (ee page.9) quare uide Pins ard hrome Plated teel uperior nonrotating piston rod feature for applications such as package placement, fi gure stamping, and any application where anti-rotation and registration are critical as the piston is extended and retracted. mounting block is bolted to the piston rod. his block has two square pins mounted to it which in turn pass through guide blocks mounted on the sides of the cylinder. quare guide pins are hard chrome plated learance in uide lock ounting oles allow for adjustment to compensate for wear ounting lock lear nodized luminum uide lock ard nodized luminum ounting oles Places steel for long wear and corrosion resistance. uide blocks are hard anodized aluminum for long wear and corrosion resistance. learance in guide block mounting holes provide for adjustment and backlash control, compensation for wear, and minimal rotation. xtended distance between guides provides superior nonrotation and support. xtended piston rod provides clearance between cylinder and guide bar mounting block to eliminate pinch points. ounting eries Q or Q ore /" /8" /8" " #6- #8- /-0 /6-8 --

22 eries Q, Q & Q Option pecifications agnetic Piston Option- Includes ovetail ounting lots Order ensors eparately ovetail style sensors are actuated by a magnetic piston. ensor dovetail slides into a mating slot on the cylinder body, is positioned as desired, and locked in place with a slotted set screw. agnetic piston and /" ovetail mounting slot(s) are specifi ed with uffi x Option "" in the model number. Order sensors separately. ensor slots at positions # and # ensor slot at position # only ow Profile, olid tate, agnetic Piston Position ensors # troke od nd Port # ensor stick-out: /" ore =.07" Other bores =."." ef. to 60 wire outlet Q Profile Q Profile Q Profile tandard troke & lot ocation uide Q (ide ap) Q (ace ount) Q (ide ug) / " / 8 " / 8 " " / " / 8 " / 8 " " 7 / 8 " / 8 " / 8 " " /8 / / / -/ -/ emale ordsets for Quick isconnect ength eter eters eters Part No ensor housing rated N 6/IP67. ncased in plastic housing, dovetail style sensors are corrosion resistant. 60 wire outlet allows close mounting. Profile shown here is typical. ovetail tyle agnetic ensors emperature ange: 0 to +80 ( to +76 ) ylinder odel eries Q, Q & Q ensor ype lectronic lectronic Prewired 9 ft. Part No Quick isconnect Part No.* lectrical haracteristics Yes ourcing PNP -8 V, 0.0 mp ax current,.0 Voltage rop Yes inking NPN -8 V, 0.0 mp ax current,.0 Voltage rop Note*: Quick disconnect styles are supplied with 6 inch pigtail with male connector. Order female cordsets separately. ale od hread Option ingle od - ouble od, od nd Only - ouble od, ap nd Only - ouble od, oth nds - t'd Inch hread 0- x 0- x /6- x.7 /8- x.88 /-0 x etric od hread Option - ore emale od hread Pitch ale od hread x ength / 0.8 x.7 7/8 0.8 x.7 -/ x 9.0 -/8 0 0 x..7 x. ouble od -- Option - lank "" both ends. W "W" extension both ends. W "" extension rod end; "W" extension cap end. W "W" extension rod end; "" extension cap end. or W od nd or W + troke ap nd od xtension imensions ore / " 7 / 8 " / 8 " / 8 " " W.

23 eries & pecifications edia...ir ecommended inimum Pressure...0 psi aximum Operating Pressure...0 psi mbient & edia emperature... to +0 Prelubrication...agnalube - rease irline ubrication...ecommended ow to Order odel Number ode eries ound head quare head ore -/" " " X Ordering xample ounting X X X P quare head series, " bore, " stroke, stages extend, stage retract, clevis mount ports in-line with slot, male rod thread izing ongstroke ulti-power ylinders eries ore tages rea quivalent etract (Pistons) ore 60 psi rea " /" " " rea = otal effective piston area, square inches. quivalent ore = ore required for single piston cylinder. X X troke tandard strokes: /", ", -/", ", -/", ", ", ", 6" (Optional any other stroke 0" thru ") tages tages xtend etract X X X X X X tandard available combinations are listed above. onsult factory for ultiple xtendultiple etract Options. xtended ie ods od end only w ap end only W od and ap nds W levis ount ound head only Ports in-line with slot......p Ports 90 to slot P OPION ee pages.,. -.8 escription pecify ouble od Nonrotating ingle od N Nonrotating ouble od N ale od hread ingle od ouble od, od nd ouble od, ap nd ouble od, oth nds Viton eals (- to +00 ) V hock & peed ontrol using hydraulics. - ubber umpers od nd ap nd oth nds djustable xtend troke /8 NP Ports in eads P8 igh low Vents Port Positions ll Ports Position # tandard Position # P Position # P Position # P od nd Position # tandard Position # P Position # P Position # P ap nd Position # tandard Position # P Position # P Position # P tmospheric Vent or Ported affl e Port Position # tandard Position # P Position # P Position # P ny port or vent not specifi ed will be in Position # as shown on page. agnetic Piston - for reed switches and lectronic ensors (Order ensors separately) Note: dditional cylinder length required for Nonrotating ods " for Option - (see page.) " for Option ". --

24 ongstroke ulti-power ylinders eries ound ead, tandard, ace ount, od and ap nd 90 " ore -/" ore " ore " ore.8 emale 0.. od hread /" ex Nut.00 od ia. (Number of stages times stroke) + imension 0 0 / NP / NP. ia.. ia.. ia.. ia. eries quare ead, tandard, ide ap ount Note: ) "ore Ports at Position # NO available. ) -/, & ores /8 NP Ports (-P8) at Position # NO available. od nd Port N " ore N -/", ", & " ores 0. emale hread ap nd / Port ex Nut N N od ia. (Number of stages times stroke) + imension 0 0 / NP / NP xtended ie od ount for ound and quare ead odels W od nd Only W ap nd Only W od and ap nds " ore ie ods equally spaced -/", ", & " ores ie ods equally spaced od nd ap nd ap nd Port W /6- hread W od nd Port W /6- hread W imensions ore " -/" " "..7. stage.... stage stage /8 x. /8 x. /8 x. 7/8 x. /-0 x.7 dp /-0 x.7 dp /-0 x.7 dp /-0 x.7 dp N /6-8 x.6 dp /8-6 x.7 dp /- x dp /- x dp N W.... W

25 ongstroke ulti-power ylinders ound ead levis ount pecify mounting option Ports in line with slot Ports 90 to slot Pivot pin and retaining lockrings are included as standard. ccessories: ee page.7 ye racket its od levises Option P ore " -/" " " P Port locations in line with slot Pin ole Port locations 90 to slot Oil fi lled powdered metal Pivot Pin ushings are standard. Pivot Pin, 6 stainless steel ockrings, plated steel ouble od Option -. + troke ypical for all bores all mounting styles tandard piston rod and rod bushing on both ends of the cylinder. Use when attachment to both ends of the cylinder is required, or to indicate piston position location. lso see Option on page.8. ale od hread ingle od ouble od, od nd Only ouble od, ap nd Only ouble od, od & ap nds od Option No elief No Weakness high strength stud is threaded into the standard female rod end and retained with octite. his method eliminates the small diameter thread relief area normally required when machining male threads. his provides a much stronger rod end which can be repaired, rather than replacing the complete rod, should the thread be damaged. octite hread tud hread ore hread " /0 x /" /0 x " /0 x " /0 x ubber umpers od nd only ap nd only oth od & ap nds Option ubber umpers rubber doughnut is bonded to the cylinder head to act as the piston stop and absorb the impact of the piston. his reduces noise and absorbs energy, thus reducing damage to the cylinder and tooling due to pounding. tandard rubber mass will compress and give full stroke at 60 to 80 psi. his mass can be adjusted to meet your specifi c pressure and/or dynamic load requirements requirements. --

26 eries & Option pecifications djustable extend stroke Option - vailable all ores. or strokes through 6" ull stroke adjustment is standard. Note! o maintain operator safety features of this option, it is NO available with mounting styles: W and W. Use caution when mounting to avoid creating pinch points. Note: NO available with mounting styles P and + troke iameter + ( x troke) + troke iameter troke adjustment per revolution ee complete description on page.9. ore " -/" " " ( x troke) + troke /8 NP Ports in eads Option -P8 Use /8 NP ports for higher fl ows, air over oil systems, etc. Nonrotating od Option -N stainless steel hex rod and a hex broached bushing of 660 bearing bronze replaces the standard round rod and bushing. ported baffl e is used so the piston assembly can be retracted by the next piston back from the rod end. he normal rod head port becomes an atmospheric vent. he tolerance on rotation is ±. he hex rod design does allow for some torque loading on the shaft. owever, torque loads that induce side loading should be minimized for best overall life and performance. ex rod fl ats have andom otation relative to ounting Pattern ex od No rod seal V V tmospheric Vent for all extend/retract combinations etract Port in affl e + [ ee hart ] ee page. for imension. No. of otal vailable Ported No. of ombinations affles tages X X X X X X dd to ex imension od /8 NP Ports etract for each cross t'd Ports (P8) ore Port Ported affle lats V V max V V max " / NP ".7" /" / NP ".7" " / NP ".7" " / NP " " Nonrotating ouble od Option -N combination of the Options N and as shown above. he rod end rod is ex and the cap end rod is round. he ported baffl es are included and the imension adjustments shown for Option N must be made. xtend piston areas must also be reduced by the rod area. igh low Vents Option - he atmospheric vent in the baffl e is cut larger to provide less resistance to the air fl ow. Use when higher cycle speeds are required. Viton eals Option -V Use for elevated temperatures ( to + 00 ) or compatibility with exotic media. -- onsult engineering for compatibility information..6

27 ongstroke ulti-power ylinders nd ug ount it it includes: rackets and bolts for attaching the brackets to the cylinder heads. aterials: rackets, steel, plated crews, steel, black oxide 6 oles W ore " -/" " " W/ / O it No (Number of stages times stroke) + im. X (Number of stages times stroke) + im. W O O stage stage stage X stage X stage X stage ide ug ount it rackets may be mounted in two different positions as shown (Number of stages times it includes: stroke) + imension X rackets and oles bolts for attaching the brackets to the U/ / cylinder heads. U/ / aterials: U rackets, steel, plated U crews, steel, black oxide ore " -/" " " it No O O.6.6 O (Number of stages times stroke) + imension O (Number of stages times stroke) + im. X O oles (Number of stages times stroke) + im. Position # Position # X X X X X stage stage stage stage stage stage U stage stage stage stage stage O X stage od levises P I Pin aterials levis and tud: teel, black oxided Pin: 6 tainless teel lips: teel, plated ore ", -/", " & " Part # -6. PIN.0. I P /-0x.6 ating ye kt - ye racket its mate with Option -P or - and od levis N I ore " -/", " " od levis -6 Part # aterials racket: igh strength inc die casting ushings: Oil fi lled powdered metal crews:, teel, plated or black oxided I N /6-8x /6-8x /6-8x /-0X.7 (#)

28 eries & Option pecifications agnetic Piston Option - (Order ensors and ensor lamps eparately) Option - consists of a magnet bonded into the piston head. When the piston magnet moves past an external sensor, the magnetic field activates the sensor without physical contact. Quick isconnect ensor hown -/" bore model shown with prewired electronic sensors and mounting clamps -Piece ensor lamp shown with quick disconnect sensor snapped in place ocket ead crew WNIN his cylinder is equipped with a agnetic Piston for use with agnetically Operated ensors. Other agnetic ensitive evices hould be ept at a istance to void Inadvertent Operation. ounting he sensor snaps into a -part clamp that attaches rigidly to any of the tie rods and can be positioned anywhere along the length of the cylinder. eliability he annular piston magnet is permanently bonded into a groove in the piston. It is a polarized permanent magnet of rubber bonded barium ferrite that is very stable and is not affected by shock. Under normal usage it will remain magnetized indefi nitely. Warning xternal magnetic fi elds and/or ferrous objects may affect the strength of the piston magnet therefore affecting sensor actuation and piston position indication. Warning labels (shown left) are affi xed to the cylinder. Please note there is an increase in base length of the cylinder to accomodate the magnet. dd " to imension '' on pages.. ensor lamp tick Out imensions odel -/ -/ " " ".0" ".0.0".0" lamp ensor Piston lamp Piston ensor emale ordsets available in,, & meter lengths 9 foot prewired sensor Piston od ylinder ube agnet, ubber onded arium errite ie od, tainless teel op View ound ead tyle ylinder ead ie od, tainless teel Piston od ylinder ube ylinder ead agnet, ubber onded arium errite op View quare ead tyle ensor & lamp Ordering uide ighted agnetic Piston Position ensors Product ype eed witch lectronic lectronic -- Prewired 9 ft. Part No Quick isconnect Part Number emperature ange: 0 to + 80 ( to + 76 ) ensor housing rated N 6/IP67. lectrical haracteristics -0 V/V, 0. mp ax., 0 Watt ax., P N.O.,. Voltage rop ourcing, PNP, 6- V, 0. mp ax.,.0 Voltage rop inking, NPN, 6-V, 0. mp ax.,.0 Voltage rop emale ordsets for Quick isconnect ength eter eter eter Part Number ensor ounting lamp - for all & odels or all & odels Order Part Number Warning! o not exceed sensor ratings. Permanent damage to sensor may occur. Power supply polarity U be observed for proper operation of sensors. ee wiring diagrams included with each sensor..8