Norgren Compact. Interchangeable Pneumatic Actuator. Section 9. Single Acting Compact. Double Acting Compact Interchangeable Pneumatic Actuator

Transcription

1 Section 9 orgren Compact Interchangeable neumatic Actuator Single Acting Actuator...ACT-9-1 Double Acting Actuator...ACT-9-8 Single Acting Compact Interchangeable neumatic Actuator Double Acting Compact Interchangeable neumatic Actuator Brookville, USA hone ACT-9-1

2 Series Compact Actuators ight weight Compact design, which is considerably shorter than IS/VDA or FA equivalent. ow friction characteristics for high speed operation ard anodized body for corrosion protection and longer life Duralon rod bearing for reduced wear Chrome plated stainless steel piston rods Technical data edium: Compressed air, filtered, lubricated or non-lubricated peration: D/95000 BS parallel ports, single acting, non-cushioned, metric ports, spring return D/96000 BS parallel ports, single acting, non-cushioned, metric ports, spring extend DC/95000 T ports, single acting, non-cushioned, metric ports, spring return DC/96000 T ports, single acting, non-cushioned, metric ports, spring extend perating pressure: 14,5 to 145 psig (1 to 10 bar) perating temperature: -25 F to +250 F (-32 C to +121 C) Consult our Technical Service for use below 35 F (+2 C) Cylinder diameters: 12, 16, 20, 25, 32, 40, 50 mm Strokes: 5 mm Ø 12 to 40 mm 10 mm Ø 12 to 50 mm 20 mm Ø 50 mm See table on page on-standard strokes available on request aterials Barrel: hard anodized aluminum End caps: hard anodized aluminum alloy iston rod: stainless steel, hard chrome plated Elastomers: Buna rdering information To order a basic 25 mm bore cylinder, spring return, with a 10 mm stroke, female thread, BS parallel ports, metric thread, quote: D/95025//10. To order a basic 40 mm bore cylinder, spring extend, with a 5 mm stroke, female thread, T ports, inch thread, quote: DC/96040//5. ountings are included. See ptions selector table on page ACT-9-8. Accessories see page iston rod clevis mounting ACT-9-8 iston rod eye mounting ACT-9-8 Spring return Spring extend ACT-9-2 Brookville, USA hone

3 Series Compact Actuators Cylinder variants Symbol odel D*/95000/ D*/95000 TD*/95000 D*/96000/ D*/96000 TD*/96000 Description Standard cylinders, single acting, spring return, female rod thread, rod end Standard cylinders, single acting, spring return, male rod thread, rod end eat resistant (Viton ) seals, +400 F (+204 C) max., metric ports Standard cylinders, single acting, spring extend, female rod thread, rod end Standard cylinders, single acting, spring extend, male rod thread, rod end eat resistant ( Viton ) seals, +400 F (+204 C max., metric ports ptions selector D /9 0 / / / Temperature igh temperature (Viton seals) Substitute T orts Substitute T orts (inch threads, stroke in mm) C BS parallel (metric ports and threads, stroke in mm) peration Substitute Spring return 5 Spring extend 6 ounting Without Foot Flange rod end Flange cap end IS Flange rod end IS Flange cap end Rear clevis Tapped holes - both ends Substitute one C B I IB D A Cylinder diameters (mm) Substitute Stroke (mm) 10 mm max. (Ø 12 to 40 mm) 20 mm max. (Ø 50 mm) Variants (non-magnetic piston) Standard, female rod thread, rod end ale rod thread, rod end Substitute one For combinations of alternative cylinders consult our Technical Service. Strokes (mm) Ø Brookville, USA hone ACT-9-3

4 Series Compact Actuators Theoretical forces Air consumption D*/95000 D*/96000 Air consumption in 3 /in. stroke (l/cm stroke) Theoretical forces lb () at 87 psi (6 bar) Theoretical forces lb () at 87 psi (6 bar) at 87 psi (6 bar) Ø utstroke F1F1utstroke Instroke Instroke (52) 1.58 (7) 8.9 (40) 1.58 (7) 1.24 (0.008) 0.93 (0.006) (105) 2.81 (12.5) 15.4 (61) 2.81 (12.5) 2.17 (0.014) 1.71 (0.011) (174) 3.26 (14.5) 26.0 (116) 3.26 (14.5) 3.41 (0.022) 2.64 (0.017) (274) 4.50 (20) 44.7 (199) 4.50 (20) 5.43 (0.035) 4.19 (0.027) (460) 7.20 (32) 75.2 (335) 7.20 (32) 8.68 (0.056) 6.51 (0.042) (725) 9.90 (44) (605) 9.90 (44) (0.088) (0.074) (1123) (56.5) (907) (56.5) (0.138) (0.116) F1 = Return force of spring lb () Cylinder weights Stroke (mm) Ø Additional weight for male thread (0.09) 0.23 (0.11) ( ) (0.002) (0.11) 0.28 (0.13) ( ) (0.003) (0.14) 0.34 (0.16) ( ) (0.007) (0.20) 0.51 (0.23) ( ) 0.04 (0.017) (0.33) 0.84 (0.38) ( ) 0.09 (0.040) (0.50) 1.23 (0.56) ( ) 0.09 (0.040) 50 ( ) 1.46 (0.66) 1.82 (0.82) 0.18 (0.080) Weights in lb (kg) lease note: estimated weights for single rod models ACT-9-4 Brookville, USA hone

5 Series Compact Actuators Basic dimensions D*/95000/, D*/96000/ Ø mm 45 Ø mm Section 45 E ø 12 = 65 ø 16 = 55 ø 20 = 55 ø 25 = 45 Section Ø mm Section Section Cylinder with rod end male thread D*/95000, D*/96000 Ø mm W (4.6) Ø (2.9) Ø (12.1) Ø (11.6) Ø 32 AF Ø Stroke range A AF B Ø D E E1E (20.5) 0.34 (8) 0.67 (17.0) (6) 1.09 (27.7) 0.98 (25) 0.90 (23) (22.0) 0.34 (10) 0.73 (18.5) (8) 1.25 (31.7) 1.14 (29) 1.07 (27.2) (24.0) 0.38 (13) 0.77 (19.5) (10) ( ) 1.42 (36) 1.23 (31.2) (27.5) 0.43 (17) 0.86 (22.5) (12) ( ) 1.57 (40) 1.45 (36.9) (30.0) 0.50 (22) 0.91 (23.0) (16) ( ) 1.75 (44.5) ( ) (36.5) 0.56 (22) 1.16 (29.5) (16) ( ) 2.05 (52) ( ) (38.5) 0.75 (27) 1.20 (30.5) (20) ( ) 2.51 (63.7) ( ) Ø Stroke range Ø I Ø #8-32 x 0.21 (3 x deep) #8-32 x 0.31 (5 x deep) 1.24 (31.5) 0.20 (5) 0.14 (3.5) 0.45 (14) 0.87 (22) 0.14 (3.5) #8-32 x 0.21 (4 x deep) #8-32 x 0.31 (6 x deep) 1.46 (37.1) 0.24 (6) 0.14 (3.5) 0.45 (15.5) 1.10 (28) 0.14 (3.5) #10-32 x 0.28 (5 x deep) #10-32 x 0.31 (8 x deep) 1.85 (47) 0.31 (8) 0.18 (4.5) 0.49 (18.5) 1.42 (36) 0.22 (5.5) /4-28 x 0.39 (6 x deep) 1/4-28 x 0.37 (10 x deep) 2.02 (51.3) 0.39 (10) 0.20 (5) 0.57 (22.5) 1.57 (40) 0.22 (5.5) /16-24 x 0.50 (8 x deep) 5/16-24 x 0.50 (14 x deep) 2.32 (58.9) 0.55 (14) 0.28 (7) 0.78 (28.5) 1.34 (34) 0.22 (5.5) /8-24 x 0.50 (8 x deep) 3/8-24 x 0.63 (14 x deep) 2.72 (69) 0.55 (14) 0.28 (7) 0.91 (28.5) 1.57 (40) 0.22 (5.5) /2-20 x 0.50 (10 x deep) 1/2-20 x 0.77 (18 x deep) 3.34 (84.9) 0.67 (17) 0.31 (8) 1.08 (33.5) 1.97 (50) 0.26 (6.6) Ø Stroke range Ø W lb (kg) at 0 mm lb (kg) per 5 mm x 0.14 (6.5 x 3.5 deep) 5 x (7.0) ( ) ( ) 0.15 (0.07) 0.04 (0.02) x 0.14 (6.5 x 3.5 deep) 5 x (7.8) ( ) ( ) 0.20 (0.09) 0.04 (0.02) x 0.28 (9.0 x 7.0 deep) 5 x (8.1) ( ) ( ) 0.26 (0.12) 0.04 (0.02) x 0.28 (9.0 x 7.0 deep) 5 x (8.4) ( ) ( ) 0.37 (0.17) 0.07 (0.03) x 0.28 (9.0 x 7.0 deep) 5 x (8.7) 1.94 (49.3) 0.84 (21.4) 0.62 (0.28) 0.11 (0.05) x 0.28 (9.0 x 7.0 deep) 1/ (9.2) 2.24 (57.0) 0.84 (21.4) 0.97 (0.44) 0.13 (0.06) x 0.31 (11.0 x 8.0 deep) 1/ (10.5) 2.78 (70.6) 1.04 (26.5) 1.10 (0.50) 0.18 (0.08) Brookville, USA hone ACT-9-5

6 Series Compact Actuators ountings Tapped hole mounting both ends A R Ø R 12 #8-32 (4 x 0.7) 0.43 (11) 16 #8-32 (4 x 0.7) 0.43 (11) 16 1/4-20 (6 x 1.0) 0.67 (17) 25 1/4-20 (6 x 1.0) 0.67 (17) 32 1/4-20 (6 x 1.0) 0.67 (17) 40 1/4-20 (6 x 1.0) 0.75 (19) 50 5/16-18 (8 x 1.25) 0.75 (19) ote: Inch threads for 'C' port code. etric threads for '' port codes. etric for foot, flange, or clevis mount. Rear clevis mounting D T Ø mm T C CU CW RR C C E C CU CW RR C C Ø C CW CU C C T RR E1 E lb (kg) (5) 0.55 (14) 0.28 (7) 0.21 (5.3) 0.39 (10) 0.2 (5) 0.11 (2.8) 0.24 (6.0) 0.98 (25) 1.09 (27.7) 0.05 (0.02) (5) 0.59 (15) 0.39 (10) 0.27 (6.8) 0.47 (12) 0.2 (5) 0.11 (2.8) 0.24 (6.0) 1.14 (29) 1.25 (31.7) 0.05 (0.02) (8) 0.71 (18) 0.47 (12) 0.33 (8.3) 0.63 (16) 0.2 (5) 0.16 (4.0) 0.35 (9.0) 1.42 (36) ( ) 0.10 (0.05) (10) 0.79 (20) 0.55 (14) 0.41 (10.3) 0.79 (20) 0.2 (5) 0.16 (4.0) 0.39 (10) 1.57 (40) ( ) 0.15 (0.07) (10) 0.79 (20) 0.55 (14) 0.72 (18.3) 1.42 (36) 0.24 (6) 0.16 (4.0) 0.39 (10) 1.75 (44.5) ( ) 0.20 (0.09) (10) 0.87 (22) 0.55 (14) 0.72 (18.3) 1.42 (36) 0.31 (8) 0.16 (4.0) 0.39 (10) 2.05 (52) ( ) 0.29 (0.13) (14) 1.1 (28) 0.79 (20) 0.88 (22.3) 1.73 (44) 0.31 (8) 0.2 (5.0) 0.55 (14) 2.51 (63.7) ( ) 0.46 (0.22) For basic cylinder dimensions, see page ACT-9-6 Brookville, USA hone

7 Series Compact Actuators Foot mounting C Ø mm T T D D Ø D T lb (kg) (4.5) 0.67 (17) 1.39 (34) 1.16 (29.5) 1.73 (44) 0.53 (13.5) 0.08 (2) 0.31 (8) 0.18 (4.5) 0.11 (2.8) 0.04 (0.02) (4.5) 0.75 (19) 1.50 (38) 1.32 (33.5) 1.89 (48) 0.53 (13.5) 0.08 (2) 0.31 (8) 0.20 (5) 0.11 (2.8) 0.04 (0.02) (6.5) 0.94 (24) 1.89 (48) 1.65 (42) 2.44 (62) 0.57 (14.5) 0.13 (3.2) 0.36 (9.2) 0.23 (5.8) 0.16 (4) 0.04 (0.02) (6.5) 1.02 (26) 2.05 (52) 1.81 (46) 2.60 (66) 0.59 (15) 0.13 (3.2) 0.42 (10.7) 0.23 (5.8) 0.16 (4) 0.09 (0.04) (6.5) 1.18 (30) 2.24 (57) 2.24 (57) 2.80 (71) 0.67 (17) 0.13 (3.2) 0.44 (11.2) 0.23 (5.8) 0.16 (4) 0.09 (0.04) (6.5) 1.30 (33) 2.52 (64) 2.52 (64) 3.07 (78) 0.67 (17) 0.13 (3.2) 0.44 (11.2) 0.28 (7) 0.16 (4) 0.22 (0.10) (9) 1.54 (39) 3.11 (79) 3.07 (78) 3.74 (95) 0.71 (18) 0.13 (3.2) 0.58 (14.7) 0.31 (8) 0.20 (5) 0.24 (0.11) For basic cylinder dimensions, see page Flange rod end mounting Flange cap end mounting B IS Flange rod end mounting I IS Flange cap end mounting IB Ø mm FV FD FV F IS F F FT Ø FT FD F F FV F (5.5) 0.31 (8.0) 0.22 (5.5) ( ) 1.57 (40) 0.98 (25) 1.97 (50) (5.5) 0.31 (8.0) 0.22 (5.5) ( ) 1.57 (40) 1.18 (30) 1.97 (50) (8) 0.26 (6.5) 0.26 (6.6) ( ) 1.97 (50) 1.54 (39) 2.44 (62) (8) 0.28 (7.0) 0.26 (6.6) ( ) 1.97 (50) 1.65 (42) 2.44 (62) (8) 0.35 (9.0) 0.28 (7) 1.26 (32) 2.52 (64) 1.89 (48) 2.99 (76) (8) 0.35 (9.0) 0.35 (9) 1.42 (36) 2.83 (72) 2.13 (54) 3.47 (88) (9) 0.35 (9.0) 0.35 (9) 1.77 (45) 3.54 (90) 2.64 (67) 4.17 (106) For basic cylinder dimensions, see page FT F F on-is FD FT FD F F FV F lb (kg) 0.18 (4.5) ( ) 1.77 (45) 0.98 (25) 2.17 (55) 0.04 (0.02) 0.18 (4.5) ( ) 1.77 (45) 1.18 (30) 2.17 (55) 0.04 (0.02) 0.26 (6.5) ( ) 1.89 (48) 1.54 (39) 2.36 (60) 0.04 (0.02) 0.26 (6.5) ( ) 2.05 (52) 1.65 (42) 2.52 (64) 0.09 (0.04) 0.22 (5.5) 1.34 (34) 2.2 (56) 1.89 (48) 2.56 (65) 0.13 (0.06) 0.22 (5.5) 1.57 (40) 2.44 (62) 2.13 (54) 2.83 (72) 0.33 (0.15) 0.26 (6.5) 1.97 (50) 2.99 (76) 2.64 (67) 3.5 (89) 0.37 (0.16) FT Brookville, USA hone ACT-9-7

8 Series Compact Actuators Accessories iston rod clevis A U C Ø mm A U C E Ø odel C U E A lb (kg) Inch etric 12 C/99012/25 /99012/ (5) #8-32 (5 x 0.8 deep) 0.63 (16) 0.27 (7) 0.21 (5.3) 0.39 (10) 0.55 (14) 0.39 (10) 0.85 (21.5) 0.02 (0.01) 16 C/99016/25 /99016/ (5) #8-32 (6 x 1.0 deep) 0.83 (21) 0.39 (10) 0.26 (6.6) 0.47 (12) 0.63 (16) 0.47 (12) 1.10 (28 ) 0.02 (0.01) 20 C/99020/25 /99020/ (8) #10-32 (8 x 1.25 deep) 0.98 (25) 0.45 (11.5) 0.33 (8.3) 0.63 (16) 0.83 (21) 0.63 (16) 1.34 (34) 0.02 (0.01) 25 C/99025/25 /99025/ (10) 1/4-28 (10 x 1.25 deep) 1.18 (30) 0.55 (14) 0.41 (10.3) 0.78 (20) 0.98 (25) 0.78 (20) 1.61 (41) 0.02 (0.01) 32 C/99032/25 /99032/ (10) 5/16-24 (14 x 1.5 deep) 1.18 (30) 0.55 (14) 0.72 (18.4) 1.44 (36.6) 1.61 (41) 0.87 (22) 1.65 (42) 0.04 (0.02) 40 C/99040/25 /99032/ (10) 3/8-24 (14 x 1.5 deep) 1.18 (30) 0.55 (14) 0.72 (18.4) 1.44 (36.6) 1.61 (41) 0.87 (22) 1.65 (42) 0.04 (0.02) 50 C/99050/25 /99050/ (14) 1/2-20 (18 x 1.5 deep) 1.57 (40) 0.79 (20) 0.88 (22.4) 1.75 (44.5) 1.97 (50) 1.10 (28) 2.20 (56) 0.09 (0.04) For basic cylinder dimensions, see page rdering information To order a basic 25 mm bore cylinder, spring return, with a 10 mm stroke, BS parallel ports quote: D/95025/10 plus piston rod clevis mounting: /99025/25 iston rod eye A U C Ø mm C A U Ø odel C U A lb (kg) Inch etric 12 C/99012/32 /99012/ (5) #8-32 (5 x 0.8 deep) 0.63 (16) 0.27 (7) 0.18 (4.7) 0.38 (9.7) 0.85 (21) 0.05 (0.02) 16 C/99016/32 /99016/ (5) #8-32 (6 x 1.0 deep) 0.98 (25) 0.55 (14) 0.24 (6.2) 0.44 (11.2) 1.26 (32) 0.05 (0.02) 20 C/99020/32 /99020/ (8) #10-32 (8 x 1.25 deep) 0.98 (25) 0.45 (11.5) 0.3 (7.7) 0.63 (16) 1.34 (34) 0.10 (0.05) 25 C/99025/32 /99025/ (10) 1/4-28 (10 x 1.25 deep) 1.18 (30) 0.55 (14) 0.38 (9.7) 0.75 (19) 1.61 (41) 0.15 (0.07) 32 C/99032/32 /99032/ (10) 5/16-24 (14 x 1.5 deep) 1.18 (30) 0.55 (14) 0.69 (17.5) 0.87 (22) 1.65 (42) 0.20 (0.09) 40 C/99040/32 /99032/ (10) 3/8-24 (14 x 1.5 deep) 1.18 (30) 0.55 (14) 0.69 (17.5) 0.87 (22) 1.65 (42) 0.29 (0.13) 50 C/99050/32 /99050/ (14) 1/2-20 (18 x 1.5 deep) 1.57 (40) 0.79 (20) 0.85 (21.5) 1.06 (27) 2.2 (56) 0.73 (0.33) For basic cylinder dimensions, see page rdering information To order a basic 25 mm bore cylinder, spring return, with a 10 mm stroke, BS parallel ports, quote: D/95025/10 plus piston rod eye mounting: /99025/32 Spares Cylinder D*/95012, D*/96012 D*/95016, D*/96016 D*/95020, D*/96020 D*/95025, D*/96025 D*/95032, D*/96032 D*/95040, D*/96040 D*/95050, D*/96050 Spares kit /99012/00 /99016/00 /99020/00 /99025/00 /99032/00 /99040/00 /99050/00 ACT-9-8 Brookville, USA hone

9 Series Compact Actuators ight weight Compact design, which is considerably shorter than IS/VDA or FA equivalent. ow friction characteristics for high speed operation Duralon rod bearing for reduced wear Chrome plated stainless steel piston rods rdering information To order a basic 25 mm bore cylinder with a magnetic piston and 10 mm stroke, female rod thread, BS parallel ports, quote: D/99025//10. To order a basic 40 mm bore cylinder with a magnetic piston and 5 mm stroke, female rod thread, T ports, quote: DC/99040//5. ountings are included for cylinders up to Ø 100 mm. See odel codes table on page ACT-9-9. agnetically operated switches need to be ordered separately. Accessories Switches See page ACT on-magnetic agnetic Technical data edium: Compressed air, filtered, lubricated or non-lubricated peration: D/99000 BS parallel ports, double acting, non-cushioned, metric threads DC/99000 T ports, double acting, non-cushioned, inch threads perating pressure: 14.5 to 145 psig (1 to 10 bar) perating temperature: -25 F to +250 F (-32 C to +121 C) Consult our Technical Service for use below 35 F (+2 C) Cylinder diameters: 12, 16, 20, 25, 32, 40, 50, 63, 80, 100, 125, 140, 160 mm Strokes: See table on page ACT-9-9 on-standard strokes available on request aterials Barrel: hard anodized aluminum End caps: hard anodized aluminum alloy iston rod: stainless steel, hard chrome plated Elastomers: Buna Alternative cylinders See page ACT-9-9. Brookville, USA hone ACT-9-9

10 Series Compact Actuators Cylinder variants Symbol odel on-magnetic piston Symbol odel agnetic piston Description Catalogue page D*/99000/ D*/99000/ D*/99000/E D*/99000/F TD*/99000/ D*/99000/J D*/99000/J D*/99000/ D*/99000/ D*/99000/E D*/99000/F TD*/99000/ D*/99000/J D*/99000/J Standard female thread ale rod thread, single rod Boss, rod end female thread Boss, cap end female thread igh temperature (Viton seals) Double ended piston rod, female thread Double ended piston rod, male thread ACT-9-11/12 ACT-9-11/12 ACT-9-22 ACT-9-22 ACT-9-11 ACT-9-13/14 ACT-9-13/14 D*/99000/1 D*/99000/2 on-rotating piston rod, female thread (Ø 12 to 100 mm) ACT-9-15/16 D*/99000/3 D*/99000/4 Cylinder with guided toolplate ACT-9-19 D*/99000/5 D*/99000/6 on-rotating double ended piston rod, female thread ACT-9-17/18 D*/99000/B D*/99000/B Cylinder with bumpers both ends, female thread (standard on Ø 125, 140 & 160) ACT-9-11/12 D*/99000/S D*/99000/S Adjustable stroke, single rod, female thread n request For combinations of alternative cylinders consult our Technical Service. ptions selector D /99 / / / Temperature igh temperature (Viton seals) orts Substitute T orts (inch threads, stroke in mm) C BS parallel ports (metric ports & threads, stroke in mm) Cylinder diameters (mm) Substitute Strokes: Substitute T Ø ounting Without Foot Flange rod end Flange cap end IS Flange rod end IS Flange cap end Rear clevis Tapped holes - both ends Stroke (mm) 300 max. (see table below) Substitute one C B I IB D A Variants (non-magnetic piston) Substitute Standard, female rod thread ale rod thread, single rod one Double ended piston rod, female rod thread J Double ended piston rod, male thread, both ends J on-rotating piston rod, female rod thread 1 Cylinder with guided toolplate 3 Double ended piston rod, non-rotating, female rod thread 5 Boss, rod end, female rod thread E Boss, cap end, female rod thread F Bumpers on both ends, female rod thread (Ø mm) B Adjustable stroke, retract, single rod, female rod thread S Variants (magnetic piston) Substitute Standard, female rod thread ale rod thread, single rod Double ended piston rod, male thread, both ends J Double ended piston rod, female rod thread J on-rotating piston rod, female rod thread 2 Cylinder with guided toolplate 4 Double ended piston rod, non-rotating, female rod thread 6 Boss, rod end, female rod thread E Boss, cap end, female rod thread F Bumpers on both ends, female rod thread (Ø mm) B Adjustable stroke, retract, single rod, female rod thread S For combinations of alternative cylinders consult our Technical Service. ACT-9-10 Brookville, USA hone

11 Series Compact Actuators Theoretical forces Air consumption Theoretical forces lb () at 87 psi (6 bar) Air consumption in 3 /in. stroke (l/cm stroke) at 87 psi (6 bar) Ø utstroke Instroke utstroke Instroke (65.8) 11.3 (50.3) 1.24 (0.008) 1.09 (0.007) (120.1) 20.1 (89.0) 2.17 (0.014) 1.71 (0.011) (189.5) 32.2 (143.2) 3.41 (0.022) 2.64 (0.017) (294.0) 51.3 (228.2) 5.43 (0.035) 4.19 (0.027) (484.0) 81.8 (363.9) 8.68 (0.056) 6.51 (0.042) (754.9) (634.8) (0.088) (0.074) (1176.6) (990.6) (0.138) (0.116) (1869.1) (1683.7) (0.218) (0.196) (3014.6) (2720.5) (0.35) (0.32) (4709.8) (4288.1) (0.55) (0.52) (7360.5) (6749.3) (0.86) (0.79) (9233.6) (8622.4) (1.08) (1.01) ( ) ( ) (1.41) (1.32) Cylinder weights Stroke (mm) Ø Additional weight for male thread Additional weight for magnetic piston (0.04) (0.05) (0.08) (0.11) (0.14) (0.17) ( ) ( ) (0.004) (0.03) (0.06) (0.07) (0.12) (0.16) (0.20) (0.25) ( ) ( ) (0.007) (0.04) (0.09) (0.11) (0.19) (0.25) (0.31) (0.38) ( ) ( ) (0.015) (0.05) (0.12) (0.14) (0.22) (0.29) (0.41) (0.48) ( ) ( ) (0.040) (0.06) (0.16) (0.18) (0.27) (0.34) (0.52) (0.64) (0.82) (0.94) (0.090) (0.09) (0.27) (0.29) (0.38) (0.45) (0.62) (0.73) (1.08) (1.21) (0.090) (0.12) 50 ( ) (0.40) (0.55) (0.66) (0.96) (1.10) (1.85) (2.07) (0.180) (0.18) 63 ( ) (0.65) (0.81) (0.93) (1.26) (1.46) (2.24) (2.50) (0.180) (0.24) 80 ( ) (1.44) (1.80) (2.08) (2.83) (3.30) (3.49) (3.87) (0.350) (0.31) 100 ( ) (2.21) (2.63) (2.95) (3.80) (4.32) (5.04) (5.53) (0.600) (0.62) 125 ( ) (5.48) (6.00) (6.52) (7.17) (7.81) (8.46) (9.11) 0.31 (0.680) ( ) 140 ( ) (6.49) (7.08) (7.68) (8.42) (9.17) (9.91) (10.66) 0.31 (0.680) ( ) 160 ( ) (8.96) (9.67) (10.39) (11.29) (12.19) (13.09) (13.99) 0.48 (1.060) ( ) Weights in lb (kg) lease note: estimated weights for single rod models Switches Female cordsets odel odel ength Reed /348/RSU/2,75 /348/SU/2,75 /348/EA/2,75 /348/EA/2,75 /348/RSU/C /348/SU/C /348/EA/C /348/EA/C /73326/1 1 m /73326/2 2 m /73326/5 5 m ote: uick disconnect styles are supplied with 6 inch pigtail with male connector. rder female cordsets separately. Solid state odel Reed Solid state Voltage V a.c. V d.c. Current max. Temperature F C ED Features Cable/plug length Cable type /348/RSU/2, ma ( ) 9 ft. (2.75 m) 26-3 VC /348/SU/2, ma ( ) 9 ft. (2.75 m) 26-3 VC /348/EA/2, ma ( ) 9 ft. (2.75 m) 26-3 VC /348/EA/2, ma ( ) 9 ft. (2.75 m) 26-3 VC Full information on switches (technical data, cable materials, dimensions etc.) please refer to relevant catalogue pages Brookville, USA hone ACT-9-11

12 Series Compact Actuators Basic dimensions D/99000/ (on-magnetic) Ø mm Ø mm 45 Section 45 E ø 12 = 65 ø 16 = 55 ø 20 = 55 ø 25 = 45 Section Ø mm Section Section Cylinder with rod end male thread D*/ Ø mm W (4.6) Ø (2.9) Ø (12.1) Ø (11.6) Ø 32 AF Ø Stroke range A AF B Ø D E E1E (20.5) 0.34 (8) 0.67 (17) (6) 1.09 (27.7) 0.98 (25) 0.90 (23) (22) 0.34 (10) 0.73 (18.5) (8) 1.25 (31.7) 1.14 (29) 1.07 (27.2) (24) 0.38 (13) 0.77 (19.5) (10) ( ) 1.42 (36) 1.23 (31.2) (27.5) 0.43 (17) 0.86 (22.5) (12) ( ) 1.57 (40) 1.45 (36.9) (30) 0.50 (22) 0.91 (23) (16) ( ) 1.75 (44.5) ( ) (36.5) 0.56 (22) 1.16 (29.5) (16) ( ) 2.05 (52) ( ) (38.5) 0.75 (27) 1.20 (30.5) (20) ( ) 2.51 (63.7) ( ) (44) 0.75 (27) 1.42 (36) (20) ( ) 3.02 (76.7) ( ) (53.5) 0.93 (32) 1.71 (43.5) (25) ( ) 3.85 (97.8) ( ) (65) 1.13 (46) 2.09 (53) (30) ( ) 4.54 (115.3) ( ) (99) 1.13 (46) 3.27 (83) (36) ( ) 5.59 (142) ( ) (99) 1.13 (46) 3.27 (83) (36) ( ) 6.22 (158) ( ) (108) 1.35 (55) 3.58 (91) (40) ( ) 7.01 (178) ( ) Ø Stroke range Ø I #8-32 x 0.21 (3 x deep) #8-32 x 0.31 (5 x deep) 1.24 (31.5) 0.20 (5) 0.14 (3.5) 0.45 (14) 0.87 (22) #8-32 x 0.21 (4 x deep) #8-32 x 0.31 (6 x deep) 1.46 (37.1) 0.24 (6) 0.14 (3.5) 0.45 (15.5) 1.10 (28) #10-32 x 0.28 (5 x deep) #10-32 x 0.31 (8 x deep) 1.85 (47) 0.31 (8) 0.18 (4.5) 0.49 (18.5) 1.42 (36) /4-28 x 0.39 (6 x deep) 1/4-28 x 0.37 (10 x deep) 2.02 (51.3) 0.39 (10) 0.20 (5) 0.57 (22.5) 1.57 (40) /16-24 x 0.50 (8 x deep) 5/16-24 x 0.50 (14 x deep) 2.32 (58.9) 0.55 (14) 0.28 (7) 0.78 (28.5) 1.34 (34) /8-24 x 0.50 (8 x deep) 3/8-24 x 0.63 (14 x deep) 2.72 (69) 0.55 (14) 0.28 (7) 0.91 (28.5) 1.57 (40) /2-20 x 0.50 (10 x deep) 1/2-20 x 0.77 (18 x deep) 3.34 (84.9) 0.67 (17) 0.31 (8) 1.08 (33.5) 1.97 (50) /2-20 x 0.50 (10 x deep) 1/2-20 x.77 (18 x deep) 4.01 (101.8) 0.67 (17) 0.31 (8) 1.08 (33.5) 2.36 (60) /8-18 x 0.88 (16 x deep) 5/8-18 x 1.00 (22 x deep) 5.11 (129.8) 0.87 (22) 0.39 (10) 1.40 (43.5) 3.03 (77) /4-16 x 0.88 (20 x deep) 3/4-16 x 1.12 (26 x deep) 6.06 (153.9) 1.06 (27) 0.47 (12) 1.59 (43.5) 3.70 (94) /4-16 x 1.06 (22 x deep) 3/4-16 x 1.12 (30 x deep) 7.48 (190) 1.26 (32) 0.63 (16) 1.75 (58) 4.49 (114) /4-16 x 1.06 (22 x deep) 3/4-16 x 1.12 (30 x deep) 8.27 (210) 1.26 (32) 0.63 (16) 1.75 (58) 5.04 (128) /4-16 x 1.06 (24 x deep) 3/4-16 x 1.12 (36 x deep) 9.37 (238) 1.42 (36) 0.67 (17) 1.79 (64) 5.67 (144) Ø Stroke range Ø Ø * W (3.5) 0.26 x 0.14 (6.5 x 3.5 deep) 5 x (7) ( ) ( ) (3.5) 0.26 x 0.14 (6.5 x 3.5 deep) 5 x (7.8) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 5 x (8.1) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 5 x (8.4) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 5 x (8.7) 1.94 (49.3) 0.84 (21.4) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 1/8* 0.36 (9.2) 2.24 (57) 0.84 (21.4) (6.5) 0.43 x 0.31 (11.0 x 8.0 deep) 1/4* 0.41 (10.5) 2.78 (70.6) 1.04 (26.5) (9) 0.55 x 0.41 (14.0 x 10.5 deep) 1/4* 0.45 (11.5) 3.29 (83.6) 1.04 (26.5) (11) 0.69 x 0.53 (17.5 x 13.5 deep) 3/8* 0.55 (14) 4.09 (104) 1.18 (30) (11) 0.69 x 0.53 (17.5 x 13.5 deep) 3/8* 0.71 (18) 4.8 (121.9) 1.18 (30) (12.7) 0.83 x 0.72 (21.2 x 18.4 deep) 3/8* 0.96 (24.5) 6.02 (153) 1.53 (39) (12.7) 0.83 x 0.72 (21.2 x 18.4 deep) 3/8* 0.96 (24.5) 6.61 (168) 1.53 (39) (14.5) 0.95 x 0.83 (24.2 x 21.2 deep) 3/8* 1.08 (27.5) 7.4 (188) 1.53 (39) * ort sizes: D/99000/... = (BS parallel ports), DC/99000/... = T (T ports). ote: 5 x 0.8 port will accept #10-32 male thread fittings. ACT-9-12 Brookville, USA hone

13 Series Compact Actuators Basic dimensions D/99000/ (agnetic) Ø mm Ø mm 0.28 (7) 45 A + Reed stroke 25 mm Elect. 19 mm Reed 25 Elect (7) Reed Reed mm Elect mm Section E 45 Section ø 12 = 65 ø 16 = 55 ø 20 = 55 ø 25 = 45 Ø mm W 0.28 (7) Reed 25 Reed 25 mm Elect. Elect. 19 mm Section Section (4.6) Ø (2.9) Ø (12.1) Ø (11.6) Ø 32 Cylinder with rod end male thread D*/99000/ Ø mm AF 0.28 (7) Reed 25 Reed 25 mm Elect. 19 Elect. 19 mm Ø Stroke range A AF B Ø D E E1E (31.5) 0.34 (8) 1.10 (28) (6) 1.09 (27.7) 0.98 (25) 0.90 (23) (34) 0.34 (10) 1.20 (30.5) (8) 1.25 (31.7) 1.14 (29) 1.07 (27.2) (36) 0.38 (13) 1.24 (31.5) (10) ( ) 1.42 (36) 1.23 (31.2) (37.5) 0.43 (17) 1.28 (32.5) (12) ( ) 1.57 (40) 1.45 (36.9) (40) 0.50 (22) 1.30 (33) (16) ( ) 1.75 (44.5) ( ) (46.5) 0.56 (22) 1.56 (39.5) (16) ( ) 2.05 (52) ( ) (48.5) 0.75 (27) 1.59 (40.5) (20) ( ) 2.51 (63.7) ( ) (54) 0.75 (27) 1.81 (46) (20) ( ) 3.02 (76.7) ( ) (63.5) 0.93 (32) 2.11 (53.5) (25) ( ) 3.85 (97.8) ( ) (75) 1.13 (46) 2.48 (63) (30) ( ) 4.54 (115.3) ( ) (99) 1.13 (46) 3.27 (83) (36) ( ) 5.59 (142) ( ) (99) 1.13 (46) 3.27 (83) (36) ( ) 6.22 (158) ( ) (108) 1.35 (55) 3.58 (91) (40) ( ) 7.01 (178) ( ) Ø Stroke range Ø I #8-32 x 0.21 (3 x deep) #8-32 x 0.31 (5 x deep) 1.24 (31.5) 0.20 (5) 0.14 (3.5) 0.45 (14) 0.87 (22) #8-32 x 0.21 (4 x deep) #8-32 x 0.31 (6 x deep) 1.46 (37.1) 0.24 (6) 0.14 (3.5) 0.45 (15.5) 1.10 (28) #10-32 x 0.28 (5 x deep) #10-32 x 0.31 (8 x deep) 1.85 (47) 0.31 (8) 0.18 (4.5) 0.49 (18.5) 1.42 (36) /4-28 x 0.39 (6 x deep) 1/4-28 x 0.37 (10 x deep) 2.02 (51.3) 0.39 (10) 0.20 (5) 0.57 (22.5) 1.57 (40) /16-24 x 0.50 (8 x deep) 5/16-24 x 0.50 (14 x deep) 2.32 (58.9) 0.55 (14) 0.28 (7) 0.78 (28.5) 1.34 (34) /8-24 x 0.50 (8 x deep) 3/8-24 x 0.63 (14 x deep) 2.72 (69) 0.55 (14) 0.28 (7) 0.91 (28.5) 1.57 (40) /2-20 x 0.50 (10 x deep) 1/2-20 x 0.77 (18 x deep) 3.34 (84.9) 0.67 (17) 0.31 (8) 1.08 (33.5) 1.97 (50) /2-20 x 0.50 (10 x deep) 1/2-20 x.77 (18 x deep) 4.01 (101.8) 0.67 (17) 0.31 (8) 1.08 (33.5) 2.36 (60) /8-18 x 0.88 (16 x deep) 5/8-18 x 1.00 (22 x deep) 5.11 (129.8) 0.87 (22) 0.39 (10) 1.40 (43.5) 3.03 (77) /4-16 x 0.88 (20 x deep) 3/4-16 x 1.12 (26 x deep) 6.06 (153.9) 1.06 (27) 0.47 (12) 1.59 (43.5) 3.70 (94) /4-16 x 1.06 (22 x deep) 3/4-16 x 1.12 (30 x deep) 7.48 (190) 1.26 (32) 0.63 (16) 1.75 (58) 4.49 (114) /4-16 x 1.06 (22 x deep) 3/4-16 x 1.12 (30 x deep) 8.27 (210) 1.26 (32) 0.63 (16) 1.75 (58) 5.04 (128) /4-16 x 1.06 (24 x deep) 3/4-16 x 1.12 (36 x deep) 9.37 (238) 1.42 (36) 0.67 (17) 1.79 (64) 5.67 (144) Ø Stroke range Ø Ø * W (3.5) 0.26 x 0.14 (6.5 x 3.5 deep) 5 x (7) ( ) ( ) (3.5) 0.26 x 0.14 (6.5 x 3.5 deep) 5 x (7.8) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 5 x (8.1) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 5 x (8.4) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 1/8* 0.34 (8.7) 1.94 (49.3) 0.84 (21.4) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 1/8* 0.36 (9.2) 2.24 (57) 0.84 (21.4) (6.6) 0.43 x 0.31 (11.0 x 8.0 deep) 1/4* 0.41 (10.5) 2.78 (70.6) 1.04 (26.5) (9) 0.55 x 0.41 (14.0 x 10.5 deep) 1/4* 0.45 (11.5) 3.29 (83.6) 1.04 (26.5) (11) 0.69 x 0.53 (17.5 x 13.5 deep) 3/8* 0.55 (14.0) 4.09 (104) 1.18 (30) (11) 0.69 x 0.53 (17.5 x 13.5 deep) 3/8* 0.71 (18) 4.80 (121.9) 1.18 (30) (12.7) 0.83 x 0.72 (21.2 x 18.4 deep) 3/8* 0.96 (24.5) 6.02 (153) 1.53 (39) (12.7) 0.83 x 0.72 (21.2 x 18.4 deep) 3/8* 0.96 (24.5) 6.61 (168) 1.53 (39) (14.5) 0.95 x 0.83 (24.2 x 21.2 deep) 3/8* 1.08 (27.5) 7.40 (188) 1.53 (39) * ort sizes: D/99000/... = (BS parallel ports), DC/99000/... = T (T ports). ote: 5 x 0,8 port will accept #10-32 male thread fittings. Brookville, USA hone ACT-9-13

14 Series Compact Actuators Double ended piston rod D/99000/J (on-magnetic) Ø mm 45 A + (2 x stroke ) + stroke Ø mm A + (2 x stroke ) + stroke Section 45 E ø 12 = 65 ø 16 = 55 ø 20 = 55 ø 25 = 45 Section Ø mm A + (2 x stroke ) + stroke * Section Section Cylinders with rod end male thread D*/99000/J Ø mm W (4.6) Ø (2.9) Ø (12.1) Ø (11.6) Ø 32 AF Ø Stroke range A AF B Ø D E E1E (32.2) 0.34 (8) 0.99 (25.2) (6) 1.09 (27.7) 0.98 (25) 0.90 (23) (33.0) 0.34 (10) 1.02 (26.0) (8) 1.25 (31.7) 1.14 (29) 1.07 (27.2) (35.0) 0.38 (13) 1.02 (26.0) (10) ( ) 1.42 (36) 1.23 (31.2) (39.0) 0.43 (17) 1.14 (29.0) (12) ( ) 1.57 (40) 1.45 (36.9) (44.5) 0.50 (22) 1.20 (30.5) (16) ( ) 1.75 (44.5) ( ) (54.0) 0.56 (22) 1.57 (40.0) (16) ( ) 2.05 (52) ( ) (56.5) 0.75 (27) 1.59 (40.5) (20) ( ) 2.51 (63.7) ( ) (58.0) 0.75 (27) 1.65 (42.0) (20) ( ) 3.02 (76.7) ( ) (71.0) 0.93 (32) 2.01 (51.0) (25) ( ) 3.85 (97.8) ( ) (84.5) 1.13 (46) 2.38 (60.5) (30) ( ) 4.54 (115.3) ( ) (115) 1.13 (46) 3.27 (83.0) (36) ( ) 5.59 (142) ( ) (115) 1.13 (46) 3.27 (83.0) (36) ( ) 6.22 (158) ( ) (125) 1.35 (55) 3.58 (91.0) (40) ( ) 7.01 (178) ( ) Ø Stroke range Ø I #8-32 x 0.21 deep(3 x 0.5-5) #8-32 x 0.31 (5 x 0.8-9) 1.24 (31.5) 0.20 (5) 0.14 (3.5) 0.45 (14) 0.87 (22) #8-32 x 0.21 deep(4 x 0.7-5) #8-32 x 0.31 (6 x ) 1.46 (37.1) 0.24 (6) 0.14 (3.5) 0.45 (15.5) 1.10 (28) #10-32 x 0.28 deep(5 x 0.8-7) #10-32 x 0.31 (8 x ) 1.85 (47) 0.31 (8) 0.18 (4.5) 0.49 (18.5) 1.42 (36) /4-28 x 0.39 deep(6 x ) 1/4-28 x 0.37 (10 x ) 2.02 (51.3) 0.39 (10) 0.20 (5) 0.57 (22.5) 1.57 (40) /16-24 x 0.50 deep(8 x ) 5/16-24 x 0.50 (14 x ) 2.32 (58.9) 0.55 (14) 0.28 (7) 0.78 (28.5) 1.34 (34) /8-24 x 0.50 deep(8 x ) 3/8-24 x 0.63 (14 x ) 2.72 (69) 0.55 (14) 0.28 (7) 0.91 (28.5) 1.57 (40) /2-20 x 0.50 deep(10 x ) 1/2-20 x 0.77 (18 x ) 3.34 (84.9) 0.67 (17) 0.31 (8) 1.08 (33.5) 1.97 (50) /2-20 x 0.50 deep(10 x ) 1/2-20 x.77 (18 x ) 4.01 (101.8) 0.67 (17) 0.31 (8) 1.08 (33.5) 2.36 (60) /8-18 x 0.88 deep(16 x ) 5/8-18 x 1.00 (22 x ) 5.11 (129.8) 0.87 (22) 0.39 (10) 1.40 (43.5) 3.03 (77) /4-16 x 0.88 deep(20 x ) 3/4-16 x 1.12 (26 x ) 6.06 (153.9) 1.06 (27) 0.47 (12) 1.59 (43.5) 3.70 (94) /4-16 x 1.06 deep(22 x ) 3/4-16 x 1.12 (30 x ) 7.48 (190) 1.26 (32) 0.63 (16) 1.75 (58) 4.49 (114) /4-16 x 1.06 deep(22 x ) 3/4-16 x 1.12 (30 x ) 8.27 (210) 1.26 (32) 0.63 (16) 1.75 (58) 5.04 (128) /4-16 x 1.06 deep(24 x ) 3/4-16 x 1.12 (36 x ) 9.37 (238) 1.42 (36) 0.67 (17) 1.79 (64) 5.67 (144) Ø Stroke range Ø Ø * W (3.5) 0.26 x 0.14 (6.5 x 3.5 deep) 5 x (7.0) ( ) ( ) (3.5) 0.26 x 0.14 (6.5 x 3.5 deep) 5 x (7.8) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 5 x (8.1) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 5 x (8.4) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 1/8* 0.34 (8.7) 1.94 (49.3) 0.84 (21.4) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 1/8* 0.36 (9.2) 2.24 (57.0) 0.84 (21.4) (6.6) 0.43 x 0.31 (11.0 x 8.0 deep) 1/4* 0.41 (10.5) 2.78 (70.6) 1.04 (26.5) (9) 0.55 x 0.41 (14.0 x 10.5 deep) 1/4* 0.45 (11.5) 3.29 (83.6) 1.04 (26.5) (11) 0.69 x 0.53 (17.5 x 13.5 deep) 3/8* 0.55 (14.0) 4.09 (104) 1.18 (30.0) (11) 0.69 x 0.53 (17.5 x 13.5 deep) 3/8* 0.71 (18.0) 4.80 (121.9) 1.18 (30.0) (12.7) 0.83 x 0.72 (21.2 x 18.4 deep) 3/8* 0.96 (24.5) 6.02 (153) 1.53 (39.0) (12.7) 0.83 x 0.72 (21.2 x 18.4 deep) 3/8* 0.96 (24.5) 6.61 (168) 1.53 (39.0) (14.5) 0.95 x 0.83 (24.2 x 21.2 deep) 3/8* 1.08 (27.5) 7.40 (188) 1.53 (39.0) * ort sizes: D/99000/... = (BS parallel ports), DC/99000/... = T (T ports). ote: 5 x 0.8 port will accept #10-32 male thread fittings. ACT-9-14 Brookville, USA hone

15 Double ended piston rod D/99000/J (agnetic) Ø mm Ø mm 0.28 (7) 45 E Ø mm W ø 12 = 65 ø 16 = 55 A + (2 x stroke ) + stroke Reed mm Elect mm 0.28 (7) + A + (2 x stroke ) stroke Reed 25 Reed Elect mm Elect. 19 mm (7) Series Compact Actuators ø 20 = 55 ø 25 = 45 + A + (2 x stroke) stroke Reed 25 Reed Elect mm Elect. 19 mm Ø Stroke range A AF B Ø D E E1E (39.4) 0.34 (8) 1.28 (32.4) (6) 1.09 (27.7) 0.98 (25) 0.90 (23) (43.0) 0.34 (10) 1.42 (36.0) (8) 1.25 (31.7) 1.14 (29) 1.07 (27.2) (47.0) 0.38 (13) 1.50 (38.0) (10) ( ) 1.42 (36) 1.23 (31.2) (49.0) 0.43 (17) 1.54 (39) (12) ( ) 1.57 (40) 1.45 (36.9) (54.5) 0.50 (22) 1.59 (40.5) (16) ( ) 1.75 (44.5) ( ) (64.0) 0.56 (22) 1.97 (50.0) (16) ( ) 2.05 (52) ( ) (66.5) 0.75 (27) 1.99 (50.5) (20) ( ) 2.51 (63.7) ( ) (68.0) 0.75 (27) 2.05 (52.0) (20) ( ) 3.02 (76.7) ( ) (81.0) 0.93 (32) 2.40 (61.0) (25) ( ) 3.85 (97.8) ( ) (94.5) 1.13 (46) 2.78 (70.5) (30) ( ) 4.54 (115.3) ( ) (115) 1.13 (46) 3.27 (83.0) (36) ( ) 5.59 (142) ( ) (115) 1.13 (46) 3.27 (83.0) (36) ( ) 6.22 (158) ( ) (125) 1.35 (55) 3.58 (91.0) (40) ( ) 7.01 (178) ( ) Ø Stroke range Ø I #8-32 x.21 (3 x deep) #8-32 x 0.31 (5 x deep) 1.24 (31.5) 0.20 (5) 0.14 (3.5) 0.45 (14) 0.87 (22) #8-32 x.21 (4 x deep) #8-32 x 0.31 (6 x deep) 1.46 (37.1) 0.24 (6) 0.14 (3.5) 0.45 (15.5) 1.10 (28) #10-32 x.28 (5 x deep) #10-32 x 0.31 (8 x deep) 1.85 (47) 0.31 (8) 0.18 (4.5) 0.49 (18.5) 1.42 (36) /4-28 x.39 (6 x deep) 1/4-28 x 0.37 (10 x deep) 2.02 (51.3) 0.39 (10) 0.20 (5) 0.57 (22.5) 1.57 (40) /16-24 x.50 (8 x deep) 5/16-24 x 0.50 (14 x deep) 2.32 (58.9) 0.55 (14) 0.28 (7) 0.78 (28.5) 1.34 (34) /8-24 x.50 (8 x deep) 3/8-24 x 0.63 (14 x deep) 2.72 (69) 0.55 (14) 0.28 (7) 0.91 (28.5) 1.57 (40) /2-20 x.50 (10 x deep) 1/2-20 x 0.77 (18 x deep) 3.34 (84.9) 0.67 (17) 0.31 (8) 1.08 (33.5) 1.97 (50) /2-20 x.50 (10 x deep) 1/2-20 x.77 (18 x deep) 4.01 (101.8) 0.67 (17) 0.31 (8) 1.08 (33.5) 2.36 (60) /8-18 x.88 (16 x deep) 5/8-18 x 1.00 (22 x deep) 5.11 (129.8) 0.87 (22) 0.39 (10) 1.40 (43.5) 3.03 (77) /4-16 x.88 (20 x deep) 3/4-16 x 1.12 (26 x deep) 6.06 (153.9) 1.06 (27) 0.47 (12) 1.59 (43.5) 3.70 (94) /4-16 x 1.06 (22 x deep) 3/4-16 x 1.12 (30 x deep) 7.48 (190) 1.26 (32) 0.63 (16) 1.75 (58) 4.49 (114) /4-16 x 1.06 (22 x deep) 3/4-16 x 1.12 (30 x deep) 8.27 (210) 1.26 (32) 0.63 (16) 1.75 (58) 5.04 (128) /4-16 x 1.06 (24 x deep) 3/4-16 x 1.12 (36 x deep) 9.37 (238) 1.42 (36) 0.67 (17) 1.79 (64) 5.67 (144) Ø Stroke range Ø Ø * W (3.5) 0.26 x 0.14 (6.5 x 3.5 deep) 5 x (7.0) ( ) ( ) (3.5) 0.26 x 0.14 (6.5 x 3.5 deep) 5 x (7.8) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 5 x (8.1) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 5 x (8.4) ( ) ( ) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 1/8* 0.34 (8.7) 1.94 (49.3) 0.84 (21.4) (5.5) 0.35 x 0.28 (9.0 x 7.0 deep) 1/8* 0.36 (9.2) 2.24 (57.0) 0.84 (21.4) (6.6) 0.43 x 0.31 (11.0 x 8.0 deep) 1/4* 0.41 (10.5) 2.78 (70.6) 1.04 (26.5) (9) 0.55 x 0.41 (14.0 x 10.5 deep) 1/4* 0.45 (11.5) 3.29 (83.6) 1.04 (26.5) (11) 0.69 x 0.53 (17.5 x 13.5 deep) 3/8* 0.55 (14.0) 4.09 (104) 1.18 (30.0) (11) 0.69 x 0.53 (17.5 x 13.5 deep) 3/8* 0.71 (18.0) 4.80 (121.9) 1.18 (30.0) (12.7) 0.83 x 0.72 (21.2 x 18.4 deep) 3/8* 0.96 (24.5) 6.02 (153) 1.53 (39.0) (12.7) 0.83 x 0.72 (21.2 x 18.4 deep) 3/8* 0.96 (24.5) 6.61 (168) 1.53 (39.0) (14.5) 0.95 x 0.83 (24.2 x 21.2 deep) 3/8* 1.08 (27.5) 7.40 (188) 1.53 (39.0) * ort sizes: D/99000/... = (BS parallel ports), DC/99000/... = T (T ports). ote: 5 x 0.8 port will accept #10-32 male thread fittings. Section Cylinder with rod end male thread D*/99000/J Section Reed 25 Ø mm (4.6) Ø (2.9) Ø (12.1) Ø (11.6) Ø 32 AF 0.28 (7) Section Section Elect. Reed 1925 mm Elect. mm Brookville, USA hone ACT-9-15

16 Series Compact Actuators Cylinders with non-rotating piston rod D/99000/1 (on-magnetic) Ø mm Ø mm E 0.20 (5) 0.20 (5) Section Section Ø 32 mm Ø mm 0.35 (9) Section Section W WARI: This cylinder has a non-rotating rod. To prevent internal damage hold rod by flats WE FU RETRACTED while installing or removing attachments. D T SCRATC R DET SAFT. W (4.6) Ø (2.9) Ø (12.1) Ø (11.6) Ø 32 Ø Stroke range A AF B Ø D E E1E (25.5) 0.34 (8) 0.87 (22.0) (6) 1.09 (27.7) 0.98 (25) 0.90 (23) (1.5) (27.0) 0.34 (10) 0.93 (23.5) (8) 1.25 (31.7) 1.14 (29) 1.07 (27.2) (1.5) (32.0) 0.38 (13) 1.08 (27.5) (10) ( ) 1.42 (36) 1.23 (31.2) (2.0) (35.5) 0.43 (17) 1.20 (30.5) (12) ( ) 1.57 (40) 1.45 (36.9) (2.0) (39.0) 0.50 (22) 1.26 (32.0) (16) ( ) 1.75 (44.5) ( ) (2.0) (36.5) 0.56 (22) 1.16 (29.5) (16) ( ) 2.05 (52) ( ) (2.0) (38.5) 0.75 (27) 1.20 (30.5) (20) ( ) 2.51 (63.7) ( ) (2.0) (44.0) 0.75 (27) 1.42 (36.0) (20) ( ) 3.02 (76.7) ( ) (2.0) (53.5) 0.93 (32) 1.71 (43.5) (25) ( ) 3.85 (97.8) ( ) (2.0) (65.0) 1.13 (46) 2.09 (53.0) (30) ( ) 4.54 (115.3) ( ) (2.0) Ø Stroke range Ø I Ø #8-32 x 0.21 (3 x deep) #8-32 x 0.31 (5 x deep) 1.24 (31.5) 0.20 (5.2) 0.14 (3.5) 0.45 (14) 0.87 (22) 0.14 (3.5) #8-32 x 0.21 (4 x deep) #8-32 x 0.31 (6 x deep) 1.46 (37.1) 0.24 (6) 0.14 (3.5) 0.45 (15.5) 1.10 (28) 0.14 (3.5) #10-32 x 0.28 (5 x deep) #10-32 x 0.31 (8 x deep) 1.85 (47) 0.31 (8) 0.18 (4.5) 0.49 (18.5) 1.42 (36) 0.22 (5.5) /4-28 x 0.39 (6 x deep) 1/4-28 x 0.37 (10 x deep) 2.02 (51.3) 0.39 (10) 0.20 (5) 0.57 (22.5) 1.57 (40) 0.22 (5.5) /16-24 x 0.50 (8 x deep) 5/16-24 x 0.50 (14 x deep) 2.32 (58.9) 0.55 (14) 0.28 (7) 0.78 (28.5) 1.34 (34) 0.22 (5.5) /8-24 x 0.50 (8 x deep) 3/8-24 x 0.63 (14 x deep) 2.72 (69) 0.55 (14) 0.28 (7) 0.91 (28.5) 1.57 (40) 0.22 (5.5) /2-20 x 0.50 (10 x deep) 1/2-20 x 0.77 (18 x deep) 3.34 (84.9) 0.71 (18) 0.31 (8) 1.08 (33.5) 1.97 (50) 0.26 (6.6) /2-20 x 0.50 (10 x deep) 1/2-20 x.77 (18 x deep) 4.01 (101.8) 0.71 (18) 0.31 (8) 1.08 (33.5) 2.36 (60) 0.35 (9) /8-18 x 0.88 (16 x deep) 5/8-18 x 1.00 (22 x deep) 5.11 (129.8) 0.87 (22) 0.39 (10) 1.40 (43.5) 3.03 (77) 0.43 (11) /4-16 x 0.88 (20 x deep) 3/4-16 x 1.12 (26 x deep) 6.06 (153.9) 1.06 (27) 0.47 (12) 1.59 (43.5) 3.7 (94) 0.43 (11) Ø Stroke range Ø * Ø T W x 0.14 (6.5 x 3.5) 5 x (7.0) ±0.002 (15 ±0.043) ( ) ( ) x 0.14 (6.5 x 3.5) 5 x (7.8) ±0.002 (20 ±0.052) ( ) ( ) x 0.28 (9.0 x 7.0) 5 x (8.1) ±0.002 (13 ±0.043) ( ) ( ) x 0.28 (9.0 x 7.0) 5 x (8.4) ±0.002 (15 ±0.043) ( ) ( ) x 0.28 (9.0 x 7.0) 5 x (8.7) ±0.002 (21 ±0.062) 1.94 (49.3) 0.84 (21.4) x 0.28 (9.0 x 7.0) 1/8* 0.36 (9.2) ±0.002 (28 ±0.062) 2.24 (57.0) 0.84 (21.4) x 0.31 (11.0 x 8.0) 1/4* 0.41 (10.5) ±0.002 (35 ±0.062) 2.78 (70.6) 1.04 (26.5) x 0.41 (14.0 x 10.5) 1/4* 0.45 (11.5) ±0.002 (35 ±0.062) 3.29 (83.6) 1.04 (26.5) x 0.53 (17.5 x 13.5) 3/8* 0.55 (14.0) ±0.002 (43 ±0.062) 4.09 (104) 1.18 (30.0) x 0.53 (17.5 x 13.5) 3/8* 0.71 (18.0) ±0.003 (59 ±0.074) 4.8 (121.9) 1.18 (30.0) * ort sizes: D/99000/... = (BS parallel ports), DC/99000/... = T (T ports). ote: 5 x 0.8 port will accept #10-32 male thread fittings. on-rotation accuracy Deflection of the mounting plate B ( ) at instroke position without load Ø ±2 ±1 ±1 ±1 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 ACT-9-16 Brookville, USA hone

17 Series Compact Actuators Cylinders with non-rotating piston rod D/99000/2 (agnetic) Ø mm Ø mm E Reed 25 Reed 25 mm 0.20 (5) Elect mm 0.20 (5) Reed mm Elect mm Section Section Ø 32 mm 0.28 (7) Reed 25 Reed Elect mm Elect. 19 mm Ø mm 0.35 (9) 0.28 (7) Reed 25 Elect. Reed mm Elect. 19 mm Section Section W WARI: This cylinder has a non-rotating rod. To prevent internal damage hold rod by flats WE FU RETRACTED while installing or removing attachments. D T SCRATC R DET SAFT. W (4.6) Ø (2.9) Ø (12.1) Ø (11.6) Ø 32 Ø Stroke range A AF B Ø D E E1E (36.5) 0.34 (8) 1.30 (33.0) (6) 1.09 (27.7) 0.98 (25) 0.90 (23) (1.5) (39.0) 0.34 (10) 1.40 (35.5) (8) 1.25 (31.7) 1.14 (29 ) 1.07 (27.2) (1.5) (44.0) 0.38 (13) 1.56 (39.5) (10) ( ) 1.42 (36) 1.23 (31.2) (2.0) (45.5) 0.43 (17) 1.59 (40.5) (12) ( ) 1.57 (40) 1.45 (36.9) (2.0) (49.0) 0.50 (22) 1.65 (42.0) (16) ( ) 1.75 (44.5) ( ) (2.0) (46.5) 0.56 (22) 1.56 (39.5) (16) ( ) 2.05 (52) ( ) (2.0) (48.5) 0.75 (27) 1.59 (40.5) (20) ( ) 2.51 (63.7) ( ) (2.0) (54.0) 0.75 (27) 1.81 (46.0) (20) ( ) 3.02 (76.7) ( ) (2.0) (63.5) 0.93 (32) 2.11 (53.5) (25) ( ) 3.85 (97.8) ( ) (2.0) (75.0) 1.13 (46) 2.48 (63.0) (30) ( ) 4.54 (115.3) ( ) (2.0) Ø Stroke range Ø I Ø #8-32 x 0.21 (3 x deep) #8-32 x 0.31 (5 x deep) 1.24 (31.5) 0.20 (5.2 ) 0.14 (3.5) 0.45 (14) 0.87 (22 ) 0.14 (3.5) #8-32 x 0.21 (4 x deep) #8-32 x 0.31 (6 x deep) 1.46 (37.1) 0.24 (6 ) 0.14 (3.5) 0.45 (15.5) 1.10 (28) 0.14 (3.5) #10-32 x 0.28 (5 x deep) #10-32 x 0.31 (8 x deep) 1.85 (47) 0.31 (8 ) 0.18 (4.5) 0.49 (18.5) 1.42 (36 ) 0.22 (5.5) /4-28 x 0.39 (6 x deep) 1/4-28 x 0.37 (10 x deep) 2.02 (51.3) 0.39 (10) 0.20 (5) 0.57 (22.5) 1.57 (40) 0.22 (5.5) /16-24 x 0.50 (8 x deep) 5/16-24 x 0.50 (14 x deep) 2.32 (58.9) 0.55 (14 ) 0.28 (7 ) 0.78 (28.5) 1.34 (34 ) 0.22 (5.5) /8-24 x 0.50 (8 x deep) 3/8-24 x 0.63 (14 x deep) 2.72 (69) 0.55 (14 ) 0.28 (7 ) 0.91 (28.5) 1.57 (40 ) 0.22 (5.5) /2-20 x 0.50 (10 x deep) 1/2-20 x 0.77 (18 x deep) 3.34 (84.9) 0.71 (18 ) 0.31 (8 ) 1.08 (33.5) 1.97 (50) 0.26 (6.6 ) /2-20 x 0.50 (10 x deep) 1/2-20 x.77 (18 x deep) 4.01 (101.8) 0.71 (18 ) 0.31 (8 ) 1.08 (33.5) 2.36 (60) 0.35 (9) /8-18 x 0.88 (16 x deep) 5/8-18 x 1.00 (22 x deep) 5.11 (129.8) 0.87 (22 ) 0.39 (10) 1.40 (43.5) 3.03 (77) 0.43 (11) /4-16 x 0.88 (20 x deep) 3/4-16 x 1.12 (26 x deep) 6.06 (153.9) 1.06 (27 ) 0.47 (12 ) 1.59 (43.5) 3.7 (94 ) 0.43 (11) Ø Stroke range Ø * Ø T W x 0.14 (6.5 x 3.5) 5 x (7.0) ±0.002 (15 ±0.043) ( ) ( ) x 0.14 (6.5 x 3.5) 5 x (7.8) ±0.002 (20 ±0.052) ( ) ( ) x 0.28 (9.0 x 7.0) 5 x (8.1) ±0.002 (13 ±0.043) ( ) ( ) x 0.28 (9.0 x 7.0) 5 x (8.4) ±0.002 (15 ±0.043) ( ) ( ) x 0.28 (9.0 x 7.0) 5 x (8.7) ±0.002 (21 ±0.062) 1.94 (49.3) 0.84 (21.4) x 0.28 (9.0 x 7.0) 1/8* 0.36 (9.2) ±0.002 (28 ±0.062) 2.24 (57.0) 0.84 (21.4) x 0.31 (11.0 x 8.0) 1/4* 0.41 (10.5) ±0.002 (35 ±0.062) 2.78 (70.6) 1.04 (26.5) x 0.41 (14.0 x 10.5) 1/4* 0.45 (11.5) ±0.002 (35 ±0.062) 3.29 (83.6) 1.04 (26.5) x 0.53 (17.5 x 13.5) 3/8* 0.55 (14.0) ±0.002 (43 ±0.062) 4.09 (104) 1.18 (30.0) x 0.53 (17.5 x 13.5) 3/8* 0.71 (18.0) ±0.003 (59 ±0.074) 4.8 (121.9) 1.18 (30.0) * ort sizes: D/99000/... = (BS parallel ports), DC/99000/... = T (T ports). ote: 5 x 0.8 port will accept #10-32 male thread fittings. on-rotation accuracy Deflection of the mounting plate B ( ) at instroke position without load Ø ±2 ±1 ±1 ±1 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 Brookville, USA hone ACT-9-17

18 Series Compact Actuators Cylinders with non-rotating piston rod D/99000/5 (on-magnetic) Ø mm E 0.20 (5) Ø mm 5 Section Section Ø 32 mm 9 (0.35) Ø mm A + (2 x stroke ) + stroke Section Section W W WARI: This cylinder has a non-rotating rod. To prevent internal damage hold rod by flats WE FU RETRACTED while installing or removing attachments. D T SCRATC R DET SAFT (4.6) Ø (2.9) Ø (12.1) Ø (11.6) Ø 32 Ø Stroke range A AF B Ø D E E1E (37.2) 0.34 (8) 1.19 (30.2) (6) 1.09 (27.7) 0.98 (25) 0.90 (23) (1.5) (38.0) 0.34 (10) 1.22 (31.0) (8) 1.25 (31.7) 1.14 (29) 1.07 (27.2) (1.5) (43.0) 0.38 (13) 1.34 (34.0) (10) ( ) 1.42 (36) 1.23 (31.2) (2.0) (47.0) 0.43 (17) 1.46 (37.0) (12) ( ) 1.57 (40) 1.45 (36.9) (2.0) (53.5) 0.50 (22) 1.56 (39.5) (16) ( ) 1.75 (44.5) ( ) (2.0) (54.0) 0.56 (22) 1.57 (40.0) (16) ( ) 2.05 (52) ( ) (2.0) (56.5) 0.75 (27) 1.59 (40.5) (20) ( ) 2.51 (63.7) ( ) (2.0) (58.0) 0.75 (27) 1.65 (42.0) (20) ( ) 3.02 (76.7) ( ) (2.0) (71.0) 0.93 (32) 2.01 (51.0) (25) ( ) 3.85 (97.8) ( ) (2.0) (84.5) 1.13 (46) 2.38 (60.5) (30) ( ) 4.54 (115.3) ( ) (2.0) Ø Stroke range Ø I Ø #8-32 x 0.21 (3 x deep) #8-32 x 0.31 (5 x deep) 1.24 (31.5) 0.20 (5.2) 0.14 (3.5) 0.45 (14) 0.87 (22) 0.14 (3.5) #8-32 x 0.21 (4 x deep) #8-32 x 0.31 (6 x deep) 1.46 (37.1) 0.24 (6) 0.14 (3.5) 0.45 (15.5) 1.10 (28) 0.14 (3.5) #10-32 x 0.28 (5 x deep) #10-32 x 0.31 (8 x deep) 1.85 (47) 0.31 (8) 0.18 (4.5) 0.49 (18.5) 1.42 (36) 0.22 (5.5) /4-28 x 0.39 (6 x deep) 1/4-28 x 0.37 (10 x deep) 2.02 (51.3) 0.39 (10) 0.20 (5) 0.57 (22.5) 1.57 (40) 0.22 (5.5) /16-24 x 0.50 (8 x deep) 5/16-24 x 0.50 (14 x deep) 2.32 (58.9) 0.55 (14) 0.28 (7) 0.78 (28.5) 1.34 (34) 0.22 (5.5) /8-24 x 0.50 (8 x deep) 3/8-24 x 0.63 (14 x deep) 2.72 (69) 0.55 (14) 0.28 (7) 0.91 (28.5) 1.57 (40) 0.22 (5.5) /2-20 x 0.50 (10 x deep) 1/2-20 x 0.77 (18 x deep) 3.34 (84.9) 0.71 (18) 0.31 (8) 1.08 (33.5) 1.97 (50) 0.26 (6.6) /2-20 x 0.50 (10 x deep) 1/2-20 x.77 (18 x deep) 4.01 (101.8) 0.71 (18) 0.31 (8) 1.08 (33.5) 2.36 (60) 0.35 (9) /8-18 x 0.88 (16 x deep) 5/8-18 x 1.00 (22 x deep) 5.11 (129.8) 0.87 (22) 0.39 (10) 1.40 (43.5) 3.03 (77) 0.43 (11) /4-16 x 0.88 (20 x deep) 3/4-16 x 1.12 (26 x deep) 6.06 (153.9) 1.06 (27) 0.47 (12) 1.59 (43.5) 3.7 (94) 0.43 (11) Ø Stroke range Ø * Ø T W x 0.14 (6.5 x 3.5) 5 x (7.0) ±0.002 (15 ±0.043) ( ) ( ) x 0.14 (6.5 x 3.5) 5 x (7.8) ±0.002 (20 ±0.052) ( ) ( ) x 0.28 (9.0 x 7.0) 5 x (8.1) ±0.002 (13 ±0.043) ( ) ( ) x 0.28 (9.0 x 7.0) 5 x (8.4) ±0.002 (15 ±0.043) ( ) ( ) x 0.28 (9.0 x 7.0) 5 x (8.7) ±0.002 (21 ±0.062) 1.94 (49.3) 0.84 (21.4) x 0.28 (9.0 x 7.0) 1/8* 0.36 (9.2) ±0.002 (28 ±0.062) 2.24 (57.0) 0.84 (21.4) x 0.31 (11.0 x 8.0) 1/4* 0.41 (10.5) ±0.002 (35 ±0.062) 2.78 (70.6) 1.04 (26.5) x 0.41 (14.0 x 10.5) 1/4* 0.45 (11.5) ±0.002 (35 ±0.062) 3.29 (83.6) 1.04 (26.5) x 0.53 (17.5 x 13.5) 3/8* 0.55 (14.0) ±0.002 (43 ±0.062) 4.09 (104) 1.18 (30.0) x 0.53 (17.5 x 13.5) 3/8* 0.71 (18.0) ±0.003 (59 ±0.074) 4.8 (121.9) 1.18 (30.0) * ort sizes: D/99000/... = (BS parallel ports), DC/99000/... = T (T ports). ote: 5 x 0.8 port will accept #10-32 male thread fittings. on-rotation accuracy Deflection of the mounting plate B ( ) at instroke position without load Ø ±2 ±1 ±1 ±1 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 ACT-9-18 Brookville, USA hone