CATALOG GC Global Series Air Cylinders

Transcription

1 CTO C lobal Series ir Cylinders

2 lobal Series Cylinders Providing Unmatched NO OO T YOU ET Page Here is FCO-I's Expanded ine of Space Saving ir Cylinders Innovation For 0 years our famous Pancakes have dominated as the world's first compact air cylinder line. Today, backed by decades of engineering innovation, our new lobal Series extruded body cylinders continue in the Pancake tradition with exceptional performance and the widest available selection of models and options. Packed with Value Tough, rigid, hard anodized aluminum extrusions house oversized hard chrome stainless steel piston rods for service to 10 bar (1 psi). agnetic piston position sensing enables mid-stroke signaling and exact end-of-stroke sensing. ultiple dovetails each accoodate multiple switches without the need for switch mounting brackets. Duralon od earings Excel oad Capacity (psi) Friction Properties achine Design 197/73 Slip- earing eference Issue Coefficient stick Porous ronze...,0 Steel-on-steel.... Yes Porous iron... 8,000 ronze-on-steel Yes Phenolics... 6,000 Sintered ronze-on-steel Nylon... 1,000 with mineral oil No TFE... 0 ronze-on-steel einforced Telfon...,0 with mineral oil.... No *TFE fabric... 60,000 Copper lead alloy-on-steel.... Yes Polycarbonate... 1,000 cetal-on-steel.... No cetal... 1,000 Nylon-on-steel....3 Yes Carbon-graphite Duralon-on-steel No * Shows Duralon bearing classification. Not to be used for design purposes. Printed with permission by exnord Corp. Extra ong Piston od earing The better the bearing is, the more cycle life you can expect from your cylinders. nd lobal Series Cylinders incorporate a truly superior rod bearing material Duralon with the same field-proven performance you have come to expect from the five other Fabco-ir cylinder families. Duralon is a composite of a Teflon /Dacron fabric liner bonded to a supporting filament-wound, high strength, fiberglass and epoxy resin shell. esistant to corrosion, moisture and temperature to 35, Duralon is reliable in any environment. It has an extremely high load bearing capacity, very low friction, and will not gall or score the piston rod (See physical properties in the above table). Teflon is a registered trademark of DuPont Corp. 9--0

3 Performance and the idest Selection of odels & Options PODUCT INDEX lobal Series How to order... 9 Standard Stroke & Options vailability..., 5 Effective Piston reas, eights... 8 Construction and Parts ists... 6, 7 Double cting Dimensions Single od... 10, 11 Double od..., 13 Double od, Hole Thru..., Nonrotating Piston od Single cting Dimensions Spring etract/spring Extend... 18, 19 Spring forces... 8 Cylinder Options & ccessories djustable Stroke Extend... 8, 9 djustable Stroke etract ack to ack Cylinders... 3, 35 Tandem Cylinders... 3, 35 High Temperature Seals agnetic Piston Position Sensors Female Cordsets for uick Disconnects ounting Options Foot ount oss ount, Front & ear Flange ounts, Front & ear... 3 ear Clevis ount od Clevis od Eye Seal its lobal Series with agnetic Piston Position Sensing Double cting Dimensions Single od..., 1 Double od..., 3 Double od, Hole Thru..., 6 Nonrotating Piston od NE lobal Series uided Toolplate Features How to Order Specifications & Dimensions Supported by engineering and inventory Cylinder components are on the shelf. CD libraries of drawings for each model and option are available on disk and at our web site ready for downloading. e're ready to work with you. Phone: (35) ; eb site E-ail: fabco@fabco-air.com. Plenty to Choose From 10 bore sizes through ( 1 /" "). Strokes 5 through 1 (." 6"). 3 Choices of ports NPT, SP Parallel, SP Tapered. Choice of rod ends female with wrench flats or male rod with wrench flats and jam nut etric or Inch rod thread and mounting. ctuation double acting, single rod; double acting, double rod; non-rotating double acting, single rod or double rod; single acting, single rod spring retract or spring extend. agnetic piston models for position sensors including electronic sensors and reed switches. 10 mounting accessories including flange mounts (rod or cap end with ISO or Non-ISO pattern), rear clevis mount (rear clevis, rod clevis, rod eye), boss mount (rod or cap), and foot mounts. Unique, adjustable stroke models. 3-position and -position models. umpers and choice of seal materials... all backed by a 3 month, 11 million cycle warranty! Page 3

4 lobal Series Cylinders ctuation Standard ounting Standard Strokes Note: Use internal stroke collar to obtain intermediate stroke from longer stroke cylinders. Stroke tolerances thru / 0 Stroke () Thru Hole Thru Hole Thru Hole Thru Hole Thru Hole Size () Size () Size () Size () Size () Page 9--0

5 Standard Strokes, Features & Options vailability Features and Options Standard Series agnetic Piston Series Tapped Hole Flange ounts ounting Options Foot ount ear Clevis ount Front oss ount ear oss ount ale od End Cylinder Options djustable Stroke High Temp Seals umpers Double cting Single od Double cting Double od Double cting, Single od Non-otating Double cting, Double od Non-otating Single cting Spring etract Single cting Spring Extend 9--0 Page 5

6 lobal Series Cylinders Construction Standard Cylinder odels Single cting/spring Extend Single cting/spring etract Extended Strokes Single od/nonrotating Single od/double cting ale od Thread Optional Double od/double cting Single od/oss ount Single od/umpers Front & ear asic Construction No uick eference to Components Description Cylinder body Piston Piston rod ushing cap ock ring od bearing End cap Spring Piston seal od seal asket umper od end nut nnular magnet od seal earing strip aterial Hard nodized luminum luminum alloy Stainless steel luminum alloy Carbon steel Duralon luminum alloy usic wire Internal lube O-ring Internal lube O-ring una N ubber Carbon steel ubber bonded una N TFE compound Note Extruded with dovetails Hard chrome plated lack anodized Zinc chromate See note 1 below lack anodized Viton optional Viton optional Viton optional Plated See notes & 3 below olded shape U cup See page 7 Note 1: earing material for, & bores is hard anodized aluminum Note : agnetic material, & bores: rare earth neodymium Note 3: agnetic material 5 bore and up: barium ferrite Cylinder ody aterial is a custom aluminum extrusion with integral dovetail slots to provide mounting for piston position sensors. Its heavy wall prohibits damage to the bore from external influences. The is Polished to produce a fine crosshatch finish. This finish, unlike an ultra-smooth finish, provides minute oil rings in which the lubrication can lie and support the seal as it moves along the surface. This surface finish and lubrication lowers friction and prolongs seal life. The Cylinder is Hard nodized inside and out. Hard anodizing is an electrochemical process which provides a very dense surface of aluminum oxide that actually impregnates the base aluminum. It forms an extremely hard (60 c) surface with a low coefficient of friction. Hardness, corrosion resistance and wear resistance exceeds that of chrome plated steel. n Extra ong od earing provides long and rigid support for the piston rod. The bearing material is Hard nodized luminum on the small, & bores, and Duralon on all larger bore sizes. See the chart comparing physical properties on page. The bushing cap and end cap are held in place by a lockring. The Piston od is Hard Chrome Plated Stainless Steel. The standard rod end is fine thread tapped and has long wrench flats. Piston Construction The piston is aluminum for light weight. counterbore locates the piston rod with precise concentricity for smooth cylinder performance. For single rod cylinders the piston is attached to the piston rod with a socket flat head screw which is torqued for both proper preload on the screw and secure clamping Page

7 ir Cylinders with 35 Years anufacturing Experience uilt-in of the piston. octite on the threads and faces assures sealing and locks the assembly against pounding and vibration. For double rod cylinders the piston rods are connected by a high strength stud, sandwiching the piston between the rod end faces. Counterbores locate the rods for alignment and precise concentricity. The assembly is torqued and octited. Standard & ong Stroke Cylinder Pistons are thin with a single O-ring for space savings. Extended Stroke Cylinder Pistons are thicker and incorporate a bearing in addition to the O-ring seal. The bearing is a close tolerance, rectangular cross section strip of a tough, stable, wear-resistant TFE compound located at the rear of the piston head, the furthest point from the rod bearing. The bearing material and its location provide maximum load support and maintain the long life of the cylinder bore and piston seal. Standard Seals are Internally ubricated, odified una N O-rings enefits include low profile cylinder construction, low friction, and long life sealing over an operating temperature range of 3 C to +1 C (5 F to + F). dditionally, all units are factory lubricated with agnalube, a grease loaded with microscopic size particles of TFE in suspension. This combination has been found suitable for long life in most non-lube service applications. Viton seals are optional for high temperature resistance ( C and 00 F) and resistance to many hostile fluids. agnetic Piston Cylinders agnetic Piston Position Sensing enables midstroke signaling and exact end-of-stroke sensing. hen the magnetic piston moves under a sensor the magnetic field activates the sensor without physical contact. sensor can be positioned anywhere in one of the dovetail slots and locked in position by an integral screw. ultiple sensors can be installed in one or more of the dovetails. The sensor(s) provides precise piston position indication for controllers, computers, relays, valves, or other devices. (See page 37 for sensor models) For 5 bore cylinders and up, a polarized permanent magnet of rubber bonded barium ferrite is used. It is very stable and unaffected by vibration and shock. Under normal usage it will remain magnetized indefinitely. For, and bores (which have higher ratios of cylinder wall thickness to piston diameter)a rare earth neodymium magnetic material is used to assure consistently reliable sensor performance. External magnetic fields and/or magnetic conductive materials may affect the strength of the piston magnets, therefore affecting sensor actuation and piston position indication agnetic Piston odels Extended Strokes hen a sensor is mounted to indicate a mid-stroke position, the moving piston causes the sensor to provide a momentary signal. If signal duration is less than, or marginally close to what is required for the driven device a user-supplied latching circuit (or similar) may be needed. Single od/nonrotating Duralon is a registered trademark of exnord Corp. octite is a registered trademark of octite Corp. agnalube is a registered trademark of Carlton Stuart Corp. Teflon and Viton are registered trademarks of DuPont Corp Single od/double cting ale od Thread Optional Double od/double cting Single od/double cting umpers Front and ear Single od/double cting ear oss ount 5 7 Page 7

8 lobal Series Cylinders Specifications Connectors for the NE agnetic Position Sensors See page 36 Sensor Pigtail 3 (1.3) Effective Piston reas cm Push in (.33) cm , or 5 eter Cable 9.8 (.39) Pull 3 (1.6) in Spring etract Forces Pre-load kg lbs Pre-load kg lbs Conversions End of Stroke kg lbs Spring Extend Forces End of Stroke kg lbs ultiply by Newton g (force) lb (force) Newton lb (force) g (force) psi bar Force (lb) = P (psi) x (in ) Force (Newton) = P (bar) x (cm ) x (0.088) 61 (0.135) 91 (0.1) 118 (0.60) 157 (0.36) 7 (0.600) Estimated Cylinder eights - Double cting, Single od odels Note: eights in rams (Pounds) Strokes in millimeters 10 7 (.10) 7 (.159) 1 (.7) 139 (.306) 1 (.397) 9 (.68) 01 (.88) 67 (1.3) 13 (3.18) 8 (.87) (.5) 1 (.56) 193 (.6) (.9) 70 (.595) 38 (.8) 551 (1.1) 7 (1.78) 1 (3.98) (5.) 109 (.0) 0 (.353) 5 (.559) 87 (.1) 339 (.76) 8 (.986) 6 (1.6) 97 (.0) 76 (.57) 9 (6.9) (.309) (.) 311 (.68) 08 (.899) 5 (1.15) (1.37) 958 (.11) 57 (.77) 830 (6.) 31 (8.38) 17 (.378) 8 (.56) 375 (.86) 8 (1.067) 6 (1.0) 733 (1.6) 110 (.3) (3.3) 396 (7.7) 318 (9.5) 5 8 (1.81) 1077 (.37) 188 (.07) 3 (.9) 39 (7.70) 36 (11.10) (.06) 11 (.67) 66 (.55) 99 (5.51) 3870 (8.5) 5531 (.18) dditional weight for male thread (.00) 3 (.007) 7 (.015) 17 (.0) 0 (.09) 0 (.09) (.18) (.18) 0 (.35) 70 (.60) dditional weight for magnetic piston (.03) 17 (.0) 5 (.05) 9 (.06) 39 (.09) 5 (.) (.18) 10 (.) 13 (.31) 8 (.6) Page

9 How to Order odel Number lobal Series Series Port ody N without magnetic piston D with magnetic piston D double acting S single acting, spring retract - 0 thru 0 bore only T single acting, spring extend - 0 thru 0 bore only odel ounting Stroke ction Options N NPT ports, inch rod thread SP Parallel ports, metric rod thread P SPT taper ports, metric rod thread Note 1: See page 8 for specific '' information and ordering examples S single rod double rod T double rod hole thru non-rotating single rod non-rotating double rod non-rotating double rod hole thru adjustable stroke extend adjustable stroke extend nonrotating rod (Note 1) thru hole foot mount E flange rod end F flange cap end ISO flange rod end H ISO flange cap end C rear clevis tapped both ends (Note ) Note 3 bumpers, both ends male rod, rod end N male rod, cap end P male rod, both ends E boss, rod end F boss, cap end S adjustable stroke, retract vailable only for S & models V high temperature seals XC10 back-to-back XC11 tandem (mtg at rod end) XC tandem (mtg at cap end) Note 3: Stroke tolerances thru bores: +1.0 / 0 Note : On bores, tapped holes will be inch threads for port code 'N' and metric threads for port codes '' & 'P'. Tapped holes will be metric when ordering any foot, flange, or clevis mounting. Ordering Example 1 lobal Series, NPT Ports, without agnetic Piston, Single od, ISO Flange on od End, 5, 60 Stroke, Double cting, and ale od. Note:The standard stroke chart on page shows available strokes of and stroke is obtained using an internal stroke collar with the longer 75 stroke cylinder. (See extended stroke chart on page 10 for and dimensions which apply to the 75 cylinder body). The odel Number is: NN S05 060D Ordering Example lobal Series, NPT Ports, with agnetic Piston, Single od, Through Hole Standard ount,, 75 Stroke, Double cting, ale od, and High Temperature Seals. Note: The standard stroke chart on page shows 75 stroke is available. No stroke collar is required. The odel Number is: ND S0 075D V Note: Sensors must be ordered separately. See page Page 9

10 lobal Series Cylinders Ø - Ø5 s E E H THEDS + STOE + STOE 5 5 FTS ØN THU () ØO C'OE () P PCES Dimensional Data Note 1- See page for complete stroke availability Note - Chart dimensions are shown as (inches) Stroke 0.0 (1.57) 6.5 (1.83) 8.5 (1.91) 5.0 (.13).5 (.) 75.0 (.95) ong Stroke 33.0 (1.30) 39.5 (1.56) 0.5 (1.59) 6.0 (1.81) 53.5 (.11).0 (.8) 8.7 (.3) 9. (.36) 10.5 (.1) 11.5 (.5) 1.0 (.55) 18.0 (.71) Stroke,, 5, 1 5, 1 5, 1 5, 1 5, 1 5, 1 Extended Stroke 37.3 (1.7) 33.8 (1.33) 39.7 (1.56) 36. (1.) 6.1 (1.8) 1.6 (1.6) 5.5 (.07) 7.5 (1.87) 5.8 (.) 7.8 (1.88) 6.5 (.6) 55.5 (.19) 67.3 (.65) 59.3 (.33) 7.6 (.86) 6.6 (.5) 79.5 (3.13) 69.5 (.7) 88.7 (3.9) 76.7 (3.0) 8.9 (.35) 10. (.0).1 (.8).7 (.).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Stroke ange 5~30 (0.~1.18) 5~30 (0.~1.18) 5~ (0.~.0) 5~ (0.~.0) 5 only (0.) 10~ (0.39~.0) 5~ (0.~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0).5 (0.81).0 (0.87).0 (0.9) 7.5 (1.08) 30.0 (1.18) 30.0 (1.18) 36.5 (1.) 38.5 (1.5).0 (1.73) 53.5 (.11) 65.0 (.56) 17.0 (0.67) 18.5 (0.73) 19.5 (0.77).5 (0.89) 3.0 (0.91) 3.0 (0.91) 9.5 (1.) 30.5 (1.) 36.0 (1.) 3.5 (1.71) 53.0 (.09) 6 (0.36) 8 (0.315) (0.7) (0.0) (0.0) (0.0) (0.787) (0.787) 5 (0.98) 30 (1.181) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) H (Threads) x dp minimum #8-3 x.1dp 3 x dp #8-3 x.1dp x dp #10-3 x.8 dp 5 x dp 1/-8 x.39 dp 6 x dp 5/- x. dp 8 x 1.5 dp 5/- x. dp 8 x 1.5 dp 3/8- x. dp 8 x 1.5 dp 1/- x. dp 10 x 1.5 dp 1/- x. dp 10 x 1.5 dp 5/8-18 x.88 dp x.0 dp 3/- x.88 dp x.5 dp 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 58.9 (.3) 58.9 (.3) 69 (.7) 8.9 (3.3) (.01) 9.8 (5.11) (6.06) Page

11 Double cting, Single od odels Ø3 - Ø s H THEDS ØN THU HOE () ØO C'OE (8 ) FTS od end male thread J NUT INCUDED F (HEX) inch or.3 or 8.3 or or 13.3 or 17. or.56 or.75 or 7.75 or 7.93 or or 6 F Z H THEDS H (THEDS) #8-3 x.31 lg or 5 x lg #8-3 x.31 lg or 6 x lg #10-3 x.31 lg or 8 x lg 1/-8 x.37 lg or 10 x lg 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg 1/- x.77 lg or 18 x lg 5/8-18 x 1.00 lg or x lg 3/- x 1. lg or 6 x lg inch or 0.5 or or or or or or or or or or STOE + STOE P PCES Note: Inch threads for 'N' port code. etric threads for '' & 'P' port codes. etric for foot, flange, or clevis mount. Tapped hole mounting O (THEDS) #8-3 or x 0.7 #8-3 or x 0.7 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 7/-1 or 10 x 1.5 1/-13 or x /-13 or x 1.75 O THED OTH ENDS inch or 0.3 or or or 1.13 or or 9 * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Note: 5 x 0.8 port will accept #10-3 male thread fittings. 5 (0.) 6 (0.) 1 (0.55) 1 (0.55) 1 (0.55) 17 (0.67) 17 (0.67) (0.87) 7 (1.06) 3.5 (0.1) 3.5 (0.1).5 (0.18) 5 (0.) 7 (0.8) 7 (0.8) 7 (0.8) (0.7) (0.87) 8 (1.10) 36 (1.) 0 (1.57) 3 (1.3) 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) ØN 3.5 (0.1) 3.5 (0.1) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) ØO 6.5 x 3.5 dp (0.6 x 0.1 dp) 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) 13.7 x 10.5 dp (0.5 x 0.1 dp).8 x 13.5 dp (0.66 x 0.53 dp).8 x 13.5 dp (0.66 x 0.53 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 5x0.8 1/8* 1/8* 1/* 1/* 3/8* 3/8* 7.0 (0.8) (0.3) 8. (0.33) 8.7 (0.3) 8.7 (0.3) 9. (0.36) 10.5 (0.1) 11.5 (0.5) 1.0 (0.55) 18.0 (0.71) 9.3 (1.9) 9.3 (1.9) 57.0 (.) 70.6 (.78) 83.6 (3.9) 10 (.09) 1.9 (.) Z.5 (0.65).5 (0.65) 17.8 (0.70). (0.88). (0.88) 7.0 (1.06) 7.0 (1.06) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page 11

12 lobal Series Cylinders Ø - Ø5 s E E H THEDS OTH ENDS + ( X STOE) + STOE + STOE 5 5 FTS ØN THU () ØO C'OE () P PCES Dimensional Data Note 1- See page for complete stroke availability Note - Chart dimensions are shown as (inches) Stroke 61.8 (.3) 69.5 (.7) 75.3 (.96).6 (3.17) 89.5 (3.5).7 (3.96) ong Stroke 7.8 (1.88) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) Stroke,, 5, 1 5, 1 5, 1 5, 1 5, 1 5, 1 Extended Stroke 0.8 (1.61) 3. (1.70).6 (1.99) 57.5 (.6) 61.8 (.3) 69.5 (.7) 75.3 (.96).6 (3.17) 89.5 (3.5).7 (3.96) 33.8 (1.33) 36. (1.) 1.6 (1.6) 7.5 (1.87) 7.8 (1.88) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0) 8.9 (.35) 10. (.0).1 (.8).7 (.).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) odel Code 'T' Hole Size N (N) 1.5 (.06) 1.5 (.06) (.13) (.13) (.13).0 (.).0 (.) 6.3 (.5) 6.3 (.5) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page Stroke ange 5~30 (0.~1.18) 5~30 (0.~1.18) 5~ (0.~.0) 5~ (0.~.0) 5 only (0.) 10~ (0.39~.0) 5~ (0.~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 3. (1.7) 33.0 (1.30) 35.0 (1.38) 39.0 (1.5).5 (1.75).5 (1.75) 5.0 (.13) 56.5 (.) 58.0 (.8) 71.0 (.) 8.5 (3.33) 5. (0.99) 6.0 (1.0) 6.0 (1.0) 9.0 (1.1) 30.5 (1.) 30.5 (1.) 0.0 (1.57) 0.5 (1.59).0 (1.65) 51.0 (.01) 60.5 (.38) 6 (0.36) 8 (0.315) (0.7) (0.0) (0.0) (0.0) (0.787) (0.787) 5 (0.98) 30 (1.181) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) H (Threads) x dp minimum #8-3 x.1dp 3 x dp #8-3 x.1dp x dp #10-3 x.8 dp 5 x dp 1/-8 x.39 dp 6 x dp 5/- x. dp 8 x 1.5 dp 5/- x. dp 8 x 1.5 dp 3/8- x. dp 8 x 1.5 dp 1/- x. dp 10 x 1.5 dp 1/- x. dp 10 x 1.5 dp 5/8-18 x.88 dp x.0 dp 3/- x.88 dp x.5 dp 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 58.9 (.3) 58.9 (.3) 69 (.7) 8.9 (3.3) (.01) 9.8 (5.11) (6.06)

13 Double cting, Double od odels Ø3 - Ø s H THEDS OTH ENDS ØN THU HOE () ØO C'OE (8 ) P PCES * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Note: 5 x 0.8 port will accept #10-3 male thread fittings. FTS Z + STOE + STOE + ( X STOE) Note: Inch threads for 'N' port code. etric threads for '' & 'P' port codes. etric for foot, flange, or clevis mount. od end male thread H THEDS Tapped hole mounting J NUT INCUDED F + STOE O THED OTH ENDS F (HEX) inch or.3 or 8.3 or or 13.3 or 17. or.56 or.75 or 7.75 or 7.93 or or 6 H (THEDS) #8-3 x.31 lg or 5 x lg #8-3 x.31 lg or 6 x lg #10-3 x.31 lg or 8 x lg 1/-8 x.37 lg or 10 x lg 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg 1/- x.77 lg or 18 x lg 5/8-18 x 1.00 lg or x lg 3/- x 1. lg or 6 x lg inch or 0.5 or or or or or or or or or or O (THEDS) #8-3 or x 0.7 #8-3 or x 0.7 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 7/-1 or 10 x 1.5 1/-13 or x /-13 or x 1.75 inch or 0.3 or or or 1.13 or or 9 5 (0.) 6 (0.) 1 (0.55) 1 (0.55) 1 (0.55) 17 (0.67) 17 (0.67) (0.87) (0.1) 3.5 (0.1).5 (0.18) 5 (0.) 7 (0.8) 7 (0.8) 7 (0.8) (0.7) (0.87) 8 (1.10) 36 (1.) 0 (1.57) 3 (1.3) 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) ØN 3.5 (0.1) 3.5 (0.1) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) ØO 6.5 x 3.5 dp (0.6 x 0.1 dp) 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) 13.7 x 10.5 dp (0.5 x 0.1 dp).8 x 13.5 dp (0.66 x 0.53 dp).8 x 13.5 dp (0.66 x 0.53 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 5x0.8 1/8* 1/8* 1/* 1/* 3/8* 3/8* 7.0 (0.8) (0.3) 8. (0.33) 8.7 (0.3) 8.7 (0.3) 9. (0.36) 10.5 (0.1) 11.5 (0.5) 1.0 (0.55) 18.0 (0.71) 9.3 (1.9) 9.3 (1.9) 57.0 (.) 70.6 (.78) 83.6 (3.9) 10 (.09) 1.9 (.) Z.5 (0.65).5 (0.65) 17.8 (0.70). (0.88). (0.88) 7.0 (1.06) 7.0 (1.06) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page 13

14 lobal Series Cylinders Ø - Ø5 s E ØN THU () ØO C'OE () + STOE + STOE H TP ØT arning THIS CYINDE HS NON-OTTIN OD. TO PEVENT INTEN DE HOD OD Y FTS ONY HEN FUY ETCTED HIE INSTIN O EOVIN TTCHENTS. DO NOT SCTCH O DENT SHFT. Dimensional Data Note 1- See page for complete stroke availability Note - Chart dimensions are shown as (inches) od flats (Dim. ) nominally in-line with ports P PCES 5 5 (.) 5 (.) 8 (.3) 8 (.3) size Nonrotating rod accuracy ± ±1 ±1 ±1 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 ± Stroke 9.0 (1.93) 6.5 (1.83) 8.5 (1.91) 5.0 (.13).5 (.) 75.0 (.95) ong Stroke.0 (1.65) 39.5 (1.56) 0.5 (1.59) 6.0 (1.81) 53.5 (.11).0 (.8) 8.7 (.3) 9. (.36) 10.5 (.1) 11.5 (.5) 1.0 (.55) 18.0 (.71) Stroke,, 5, 1 5, 1 5, 1 5, 1 5, 1 5, 1 Extended Stroke.3 (1.67) 38.8 (1.53).7 (1.76) 1. (1.6) 5.1 (.13) 9.6 (1.95) 60.5 (.38) 55.5 (.19).8 (.51) 56.8 (.) 6.5 (.6) 55.5 (.19) 67.3 (.65) 59.3 (.33) 7.6 (.86) 6.6 (.5) 79.5 (3.13) 69.5 (.7) 88.7 (3.9) 76.7 (3.0) 8.9 (.35) 10. (.0).1 (.8).7 (.).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Note: 5 x 0.8 port will accept #10-3 male thread fittings. (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Stroke ange 5~30 (0.~1.18) 5~30 (0.~1.18) 5~ (0.~.0) 5~ (0.~.0) 5 only (0.) 10~ (0.39~.0) 5~ (0.~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 5.5 (1.00) 7.0 (1.06) 3.0 (1.6) 35.5 (1.0) 39.0 (1.5) 39.0 (1.5) 36.5 (1.) 38.5 (1.5).0 (1.73) 53.5 (.11) 65.0 (.56).0 (0.87) 3.5 (0.93) 7.5 (1.08) 30.5 (1.) 3.0 (1.6) 3.0 (1.6) 9.5 (1.) 30.5 (1.) 36.0 (1.) 3.5 (1.71) 53.0 (.09) 6 (0.36) 8 (0.315) (0.7) (0.0) (0.0) (0.0) (0.787) (0.787) 5 (0.98) 30 (1.181) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) H (Threads) x dp minimum #8-3 x.1dp 3 x dp #8-3 x.1dp x dp #10-3 x.8 dp 5 x dp 1/-8 x.39 dp 6 x dp 5/- x. dp 8 x 1.5 dp 5/- x. dp 8 x 1.5 dp 3/8- x. dp 8 x 1.5 dp 1/- x. dp 10 x 1.5 dp 1/- x. dp 10 x 1.5 dp 5/8-18 x.88 dp x.0 dp 3/- x.88 dp x.5 dp 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 58.9 (.3) 58.9 (.3) 69 (.7) 8.9 (3.3) (.01) 9.8 (5.11) (6.06) Page

15 Double cting, Nonrotating Piston od odels Ø3 H TP ØN THU HOE () ØO C'OE () P PCES Z ØT (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Slots () for ound Profile Sensors ØT 15 +0/ 0.03 ( /0.00) +0/ 0.05 ( /0.00) 13 +0/ 0.03 (0.5 +0/0.00) 15 +0/ 0.03 ( /0.00) 1 +0/ 0.06 ( /0.00) 8 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 3 +0/ 0.06 ( /0.00) 59 +0/ 0.07 (.33 +0/ (.35) + STOE + STOE 1.5 (0.059) 1.5 (0.059).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079 Ø0 - Ø s H TP ØN THU HOE () ØO C'OE (8) Z ØT P PCES od flats (Dim. ) nominally in-line with ports + STOE + STOE od end male thread J NUT INCUDED F H THEDS Tapped hole mounting Note: Inch threads for 'N' port code. etric threads for '' & 'P' port codes. etric for foot, flange, or clevis mount. O THED OTH ENDS F (HEX) inch or.3 or 8.3 or or 13.3 or 17. or.56 or.75 or 7.75 or 7.93 or or 6 H (THEDS) #8-3 x.31 lg or 5 x lg #8-3 x.31 lg or 6 x lg #10-3 x.31 lg or 8 x lg 1/-8 x.37 lg or 10 x lg 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg 1/- x.77 lg or 18 x lg 5/8-18 x 1.00 lg or x lg 3/- x 1. lg or 6 x lg inch or 0.5 or or or or or or or or or or O (THEDS) #8-3 or x 0.7 #8-3 or x 0.7 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 7/-1 or 10 x 1.5 1/-13 or x /-13 or x 1.75 Places Front F inch or 0. or 0. or 0.98 or or or or 1.13 or or 9 Places ear inch or 0.3 or or or 1.13 or or 9 5. (0.) 6 (0.) 1 (0.55) 1 (0.55) 1 (0.55) 18 (0.71) 18 (0.71) (0.87) 7 (1.06) 3.5 (0.1) 3.5 (0.1).5 (0.18) 5 (0.) 7 (0.8) 7 (0.8) 7 (0.8) (0.7) (0.87) 8 (1.10) 36 (1.) 0 (1.57) 3 (1.3) 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) ØN 3.5 (0.1) 3.5 (0.1) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) ØO 6.5 x 3.5 dp (0.6 x 0.1 dp) 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) 13.7 x 10.5 dp (0.5 x 0.1 dp).8 x 13.5 dp (0.66 x 0.53 dp).8 x 13.5 dp (0.66 x 0.53 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 5x0.8 1/8* 1/8* 1/* 1/* 3/8* 3/8* 7.0 (0.8) (0.3) 8. (0.33) 8.7 (0.3) 8.7 (0.3) 9. (0.36) 10.5 (0.1) 11.5 (0.5) 1.0 (0.55) 18.0 (0.71) 9.3 (1.9) 9.3 (1.9) 57.0 (.) 70.6 (.78) 83.6 (3.9) 10 (.09) 1.9 (.) Z.5 (0.65).5 (0.65) 17.8 (0.70). (0.88). (0.88) 7.0 (1.06) 7.0 (1.06) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page 15

16 lobal Series Cylinders Ø - Ø5 s E ØN THU () ØO C'OE () + ( x STOE) + STOE + STOE ØT arning THIS CYINDE HS NON-OTTIN OD. TO PEVENT INTEN DE HOD OD Y FTS ONY HEN FUY ETCTED HIE INSTIN O EOVIN TTCHENTS. DO NOT SCTCH O DENT SHFT. Dimensional Data Note 1- See page for complete stroke availability Note - Chart dimensions are shown as (inches) od flats (Dim. ) nominally in-line with ports H TP OTH ENDS 5 5 (.) 5 (.) 8 (.3) 8 (.3) P PCES size Nonrotating rod accuracy ± ±1 ±1 ±1 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 ± Stroke ong Stroke 70.8 (.79) 69.5 (.7) 75.3 (.96).6 (3.17) 89.5 (3.5).7 (3.96) 56.8 (.) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) Stroke,, 5, 1 5, 1 5, 1 5, 1 5, 1 5, 1 Extended Stroke 38.8 (1.53) 1. (1.6) 9.6 (1.95) 55.5 (.19) 56.8 (.) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0) 5.8 (1.) 8. (1.90) 58.6 (.31) 65.5 (.58) 70.8 (.79) 69.5 (.7) 75.3 (.96).6 (3.17) 89.5 (3.5).7 (3.96) 8.9 (.35) 10. (.0).1 (.8).7 (.).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) odel Code '' Hole Size N (N) 1.5 (.06) 1.5 (.06) (.13) (.13) (.13).0 (.).0 (.) 6.3 (.5) 6.3 (.5) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Stroke ange 5~30 (0.~1.18) 5~30 (0.~1.18) 5~ (0.~.0) 5~ (0.~.0) 5 only (0.) 10~ (0.39~.0) 5~ (0.~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 37. (1.6) 38.0 (1.) 3.0 (1.69) 7.0 (1.85) 53.5 (.11) 53.5 (.11) 5.0 (.13) 56.5 (.) 58.0 (.8) 71.0 (.) 8.5 (3.33) 30. (1.19) 31.0 (1.) 3.0 (1.3) 37.0 (1.6) 39.5 (1.56) 39.5 (1.56) 0.0 (1.57) 0.5 (1.59).0 (1.65) 51.0 (.01) 60.5 (.38) 6 (0.36) 8 (0.315) (0.7) (0.0) (0.0) (0.0) (0.787) (0.787) 5 (0.98) 30 (1.181) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) H (Threads) x dp minimum #8-3 x.1dp 3 x dp #8-3 x.1dp x dp #10-3 x.8 dp 5 x dp 1/-8 x.39 dp 6 x dp 5/- x. dp 8 x 1.5 dp 5/- x. dp 8 x 1.5 dp 3/8- x. dp 8 x 1.5 dp 1/- x. dp 10 x 1.5 dp 1/- x. dp 10 x 1.5 dp 5/8-18 x.88 dp x.0 dp 3/- x.88 dp x.5 dp 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 58.9 (.3) 58.9 (.3) 69 (.7) 8.9 (3.3) (.01) 9.8 (5.11) (6.06) Page

17 Double cting, Double od, Nonrotating Piston od odels Ø3 H TP OTH ENDS H TP OTH ENDS ØN THU HOE () ØO C'OE () Z ØT Ø0 - Ø s ØN THU HOE () ØO C'OE (8) Z ØT P PCES P PCES 9 (.35) + STOE + STOE + ( x STOE) + STOE + ( x STOE) + STOE (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () ØT 15 +0/ 0.03 ( /0.00) +0/ 0.05 ( /0.00) 13 +0/ 0.03 (0.5 +0/0.00) 15 +0/ 0.03 ( /0.00) 1 +0/ 0.06 ( /0.00) 8 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 3 +0/ 0.06 ( /0.00) 59 +0/ 0.07 (.33 +0/0.003) od flats (Dim. ) nominally in-line with ports 1.5 (0.059) 1.5 (0.059).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079) * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Note: 5 x 0.8 port will accept #10-3 male thread fittings. od end male thread F (HEX) inch or.3 or 8.3 or or 13.3 or 17. or.56 or.75 or 7.75 or 7.93 or or 6 J NUT INCUDED F H THEDS H (THEDS) #8-3 x.31 lg or 5 x lg #8-3 x.31 lg or 6 x lg #10-3 x.31 lg or 8 x lg 1/-8 x.37 lg or 10 x lg 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg 1/- x.77 lg or 18 x lg 5/8-18 x 1.00 lg or x lg 3/- x 1. lg or 6 x lg + STOE inch or 0.5 or or or or or or or or or or 3.5 Tapped hole mounting Note: Inch threads for 'N' port code. etric threads for '' & 'P' port codes. etric for foot, flange, or clevis mount O (THEDS) #8-3 or x 0.7 #8-3 or x 0.7 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 7/-1 or 10 x 1.5 1/-13 or x /-13 or x 1.75 Places Front F inch or 0. or 0. or 0.98 or or or or 1.13 or or 9 Places ear O THED OTH ENDS inch or 0.3 or or or 1.13 or or 9 5. (0.) 6 (0.) 1 (0.55) 1 (0.55) 1 (0.55) 18 (0.71) 18 (0.71) (0.87) 7 (1.06) 3.5 (0.1) 3.5 (0.1).5 (0.18) 5 (0.) 7 (0.8) 7 (0.8) 7 (0.8) (0.7) (0.87) 8 (1.10) 36 (1.) 0 (1.57) 3 (1.3) 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) ØN 3.5 (0.1) 3.5 (0.1) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) ØO 6.5 x 3.5 dp (0.6 x 0.1 dp) 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) 13.7 x 10.5 dp (0.5 x 0.1 dp).8 x 13.5 dp (0.66 x 0.53 dp).8 x 13.5 dp (0.66 x 0.53 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 5x0.8 1/8* 1/8* 1/* 1/* 3/8* 3/8* 7.0 (0.8) (0.3) 8. (0.33) 8.7 (0.3) 8.7 (0.3) 9. (0.36) 10.5 (0.1) 11.5 (0.5) 1.0 (0.55) 18.0 (0.71) 9.3 (1.9) 9.3 (1.9) 57.0 (.) 70.6 (.78) 83.6 (3.9) 10 (.09) 1.9 (.) Z.5 (0.65).5 (0.65) 17.8 (0.70). (0.88). (0.88) 7.0 (1.06) 7.0 (1.06) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page 17

18 lobal Series Cylinders Ø - Ø5 s Spring etract Spring Extend E E H THEDS + STOE + STOE + ( x STOE) + + STOE STOE 5 5 FTS ØN THU () ØO C'OE () P PCES H THEDS P PCES Note 1- See page for complete stroke availability Dimensional Data Note - Chart dimensions are shown as (inches) * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Note: 5 x 0.8 port will accept #10-3 male thread fittings. (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () Stroke ange 5~10 (0.~0.39) 5~10 (0.~0.39) 5~10 (0.~0.39) 5~10 (0.~0.39) 5 (0.) 5~10 (0.~0.39) 10~ (0.39~0.79).5 (0.81).0 (0.87).0 (0.9) 7.5 (1.08) 30.0 (1.18) 30.0 (1.18) 36.5 (1.) 38.5 (1.5) 17.0 (0.67) 18.5 (0.73) 19.5 (0.77).5 (0.86) 3.0 (0.91) 3.0 (0.91) 9.5 (1.) 30.5 (1.) 6 (0.36) 8 (0.315) (0.7) (0.0) (0.0) (0.0) (0.787) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75).5 (1.75) 5 (.05).7 (.51) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) H (Threads) x dp minimum #8-3 x.1dp 3 x dp #8-3 x.1dp x dp #10-3 x.8 dp 5 x dp 1/-8 x.39 dp 6 x dp 5/- x. dp 8 x 1.5 dp 5/- x. dp 8 x 1.5 dp 3/8- x. dp 8 x 1.5 dp 1/- x. dp 10 x 1.5 dp 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 58.9 (.3) 58.9 (.3) 69 (.7) 8.9 (3.3) Page

19 Single cting, Spring etract/spring Extend odels Ø3 - Ø s Spring etract Spring Extend H THEDS ØN THU HOE () ØO C'OE (8 ) H THEDS P PCES Z FTS od end male thread J NUT INCUDED F (HEX) inch or.3 or 8.3 or or 13.3 or 17. or.56 or.75 or 7 F H THEDS H (THEDS) #8-3 x.31 lg or 5 x lg #8-3 x.31 lg or 6 x lg #10-3 x.31 lg or 8 x lg 1/-8 x.37 lg or 10 x lg 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg etracted inch or 0.5 or or or or or or or STOE + STOE Note: Inch threads for 'N' port code. etric threads for '' & 'P' port codes. etric for foot, flange, or clevis mount. Tapped hole mounting O (THEDS) #8-3 or x 0.7 #8-3 or x 0.7 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 O THED OTH ENDS inch or 0.3 or or 11 + STOE + STOE + ( x STOE) 5 (0.) 6 (0.) 1 (0.55) 1 (0.55) 1 (0.55) 17 (0.67) 3.5 (0.1) 3.5 (0.1).5 (0.18) 5 (0.) 7 (0.8) 7 (0.8) 7 (0.8) (0.87) 8 (1.10) 36 (1.) 0 (1.57) 3 (1.3) 3 (1.3) 0 (1.57) (1.97) ØN 3.5 (0.1) 3.5 (0.1) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 6.6 (0.6) ØO 6.5 x 3.5 dp (0.6 x 0.1 dp) 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 5x0.8 1/8* 1/8* 1/* 7.0 (0.8) (0.3) 8. (0.33) 8.7 (0.3) 8.7 (0.3) 9. (0.36) 10.5 (0.1) 9.3 (1.9) 9.3 (1.9) 57.0 (.) 70.6 (.78) Z.5 (0.65).5 (0.65) 17.8 (0.70). (0.88) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () Page 19

20 lobal Series Cylinders agnetic Piston Ø - Ø5 s E E 7(.8) H THEDS + STOE + STOE eed 5 (1.00) Elect. 19 (0.75) 5 5 FTS ØN THU () ØO C'OE () P PCES Dimensional Data Stroke 0.0 (1.57) 6.5 (1.83) 8.5 (1.91) 5.0 (.13).5 (.) 75.0 (.95) ong Stroke 33.0 (1.30) 39.5 (1.56) 0.5 (1.59) 6.0 (1.81) 53.5 (.11).0 (.8) 8.7 (.3) 9. (.36) 10.5 (.1) 11.5 (.5) 1.0 (.55) 18.0 (.71) Note 1- See page for complete stroke availability Note - Chart dimensions are shown as (inches) Stroke,, 5, 1 5, 1 5, 1 5, 1 5, 1 5, 1 Extended Stroke 37.3 (1.7) 33.8 (1.33) 39.7 (1.56) 36. (1.) 6.1 (1.8) 1.6 (1.6) 5.5 (.07) 7.5 (1.87) 5.8 (.) 7.8 (1.88) 6.5 (.6) 55.5 (.19) 67.3 (.65) 59.3 (.33) 7.6 (.86) 6.6 (.5) 79.5 (3.13) 69.5 (.7) 88.7 (3.9) 76.7 (3.0) 8.9 (.35) 10. (.0).1 (.8).7 (.).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) Sensors must be ordered separately. See page 37. * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Note: 5 x 0.8 port will accept #10-3 male thread fittings. (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Stroke ange 5~30 (0.~1.18) 5~30 (0.~1.18) 5~ (0.~.0) 5~ (0.~.0) 5~ 0.~.0) 5~ (0.~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 31.5 (1.) 3.0 (1.3) 36.0 (1.) 37.5 (1.8) 0.0 (1.57) 6.5 (1.83) 8.5 (1.91) 5.0 (.13).5 (.) 75.0 (.95) 8.0 (1.10) 30.5 (1.) 31.5 (1.) 3.5 (1.8) 33.0 (1.30) 39.5 (1.56) 0.5 (1.59) 6.0 (1.81) 53.5 (.11).0 (.8) 6 (0.36) 8 (0.315) (0.7) (0.0) (0.0) (0.787) (0.787) 5 (0.98) 30 (1.181) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) H (Threads) x dp minimum #8-3 x.1dp 3 x dp #8-3 x.1dp x dp #10-3 x.8 dp 5 x dp 1/-8 x.39 dp 6 x dp 5/- x. dp 8 x 1.5 dp 3/8- x. dp 8 x 1.5 dp 1/- x. dp 10 x 1.5 dp 1/- x. dp 10 x 1.5 dp 5/8-18 x.88 dp x.0 dp 3/- x.88 dp x.5 dp 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 58.9 (.3) 69 (.7) 8.9 (3.3) (.01) 9.8 (5.11) (6.06) Page

21 Double cting, Single od odels Ø3 - Ø s ØN THU HOE () ØO C'OE (8 ) H THEDS 7 (0.8) eed 5 (1.00) Electronic19 (0.75) Slots () for ound Profile Sensors Sensors must be ordered separately. See page 37. ound Profile Sensor Shown Z P PCES FTS + STOE + STOE See page 37 for round profile sensors featuring surge suppression, polarity protection and dual output. od end male thread F (HEX) inch or.3 or 8.3 or or 13.3 or 17. or.56 or.75 or 7.75 or 7.93 or or 6 J NUT INCUDED F H (THEDS) #8-3 x.31 lg or 5 x lg #8-3 x.31 lg or 6 x lg #10-3 x.31 lg or 8 x lg 1/-8 x.37 lg or 10 x lg 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg 1/- x.77 lg or 18 x lg 5/8-18 x 1.00 lg or x lg 3/- x 1. lg or 6 x lg H THEDS inch or 0.5 or or or or or or or or or or 3.5 Tapped hole mounting O (THEDS) #8-3 or x 0.7 #8-3 or x 0.7 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 7/-1 or 10 x 1.5 1/-13 or x /-13 or x 1.75 O THED OTH ENDS inch or 0.3 or or or 1.13 or or 9 Note: Inch threads for 'N' port code. etric threads for '' & 'P' port codes. etric for foot, flange, or clevis mount. 5 (0.) 6 (0.) 1 (0.55) 1 (0.55) 17 (0.67) 17 (0.67) (0.87) 7 (1.06) 3.5 (0.1) 3.5 (0.1).5 (0.18) 5 (0.) 7 (0.8) 7 (0.8) (0.7) (0.87) 8 (1.10) 36 (1.) 0 (1.57) 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) ØN 3.5 (0.1) 3.5 (0.1) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) ØO 6.5 x 3.5 dp (0.6 x 0.1 dp) 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) 13.7 x 10.5 dp (0.5 x 0.1 dp).8 x 13.5 dp (0.66 x 0.53 dp).8 x 13.5 dp (0.66 x 0.53 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 1/8* 1/8* 1/* 1/* 3/8* 3/8* 7.0 (0.8) (0.3) 8. (0.33) 8.7 (0.3) 9. (0.36) 10.5 (0.1) 11.5 (0.5) 1.0 (0.55) 18.0 (0.71) 9.3 (1.9) 57.0 (.) 70.6 (.78) 83.6 (3.9) 10 (.09) 1.9 (.) Z.5 (0.65) 17.8 (0.70). (0.88). (0.88) 7.0 (1.06) 7.0 (1.06) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page 1

22 lobal Series Cylinders agnetic Piston Ø - Ø5 s E E 7(.8) H THEDS OTH ENDS + ( X STOE) + + STOE STOE eed 5 (1.00) Elect. 19 (0.75) 5 5 FTS ØN THU () ØO C'OE () P PCES Dimensional Data Stroke 61.8 (.3) 69.5 (.7) 75.3 (.96).6 (3.17) 89.5 (3.5).7 (3.96) ong Stroke 7.8 (1.88) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) Note 1- See page for complete stroke availability Note - Chart dimensions are shown as (inches) Stroke,, 5, 1 5, 1 5, 1 5, 1 5, 1 5, 1 Extended Stroke 33.8 (1.33) 36. (1.) 1.6 (1.6) 7.5 (1.87) 7.8 (1.88) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0) 0.8 (1.61) 3. (1.70).6 (1.99) 57.5 (.6) 61.8 (.3) 69.5 (.7) 75.3 (.96).6 (3.17) 89.5 (3.5).7 (3.96) 8.9 (.35) 10. (.0).1 (.8).7 (.).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) odel Code 'T' Hole Size N (N) 1.5 (.06) 1.5 (.06) (.13) (.13) (.13).0 (.).0 (.) 6.3 (.5) 6.3 (.5 (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Stroke ange 5~30 (0.~1.18) 5~30 (0.~1.18) 5~ (0.~.0) 5~ (0.~.0) 5~ 0.~.0) 5~ (0.~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 39. (1.55) 3.0 (1.69) 7.0 (1.85) 9.0 (1.93) 5.5 (.15) 6.0 (.5) 66.5 (.6) 68.0 (.68) 81.0 (3.19) 9.5 (3.7) 3. (1.8) 36.0 (1.) 38.0 (1.) 39 (1.5) 0.5 (1.59).0 (1.97).5 (1.99) 5.0 (.05) 61.0 (.0) 70.5 (.78) 6 (0.36) 8 (0.315) (0.7) (0.0) (0.0) (0.787) (0.787) 5 (0.98) 30 (1.181) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) H (Threads) x dp minimum #8-3 x.1dp 3 x dp #8-3 x.1dp x dp #10-3 x.8 dp 5 x dp 1/-8 x.39 dp 6 x dp 5/- x. dp 8 x 1.5 dp 3/8- x. dp 8 x 1.5 dp 1/- x. dp 10 x 1.5 dp 1/- x. dp 10 x 1.5 dp 5/8-18 x.88 dp x.0 dp 3/- x.88 dp x.5 dp 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 58.9 (.3) 69 (.7) 8.9 (3.3) (.01) 9.8 (5.11) (6.06) Page

23 Double cting, Double od odels Ø3 - Ø s H THEDS OTH ENDS ØN THU HOE () ØO C'OE (8 ) 7 (0.8) Slots () for ound Profile Sensors Z eed 5 (1.00) Electronic19 (0.75) P PCES FTS + STOE + STOE + ( X STOE) See page 37 for round profile sensors featuring surge suppression, polarity protection and dual output. Sensors must be ordered separately. See page 37. * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Note: 5 x 0.8 port will accept #10-3 male thread fittings. od end male thread J NUT INCUDED F (HEX) inch or.3 or 8.3 or or 13.3 or 17. or.56 or.75 or 7.75 or 7.93 or or 6 F H THEDS H (THEDS) #8-3 x.31 lg or 5 x lg #8-3 x.31 lg or 6 x lg #10-3 x.31 lg or 8 x lg 1/-8 x.37 lg or 10 x lg 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg 1/- x.77 lg or 18 x lg 5/8-18 x 1.00 lg or x lg 3/- x 1. lg or 6 x lg + STOE inch or 0.5 or or or or or or or or or or 3.5 Tapped hole mounting O (THEDS) #8-3 or x 0.7 #8-3 or x 0.7 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 7/-1 or 10 x 1.5 1/-13 or x /-13 or x 1.75 O THED OTH ENDS inch or 0.3 or or or 1.13 or or 9 Note: Inch threads for 'N' port code. etric threads for '' & 'P' port codes. etric for foot or flange mount. 5 (0.) 6 (0.) 1 (0.55) 1 (0.55) 17 (0.67) 17 (0.67) (0.87) 7 (1.06) 3.5 (0.1) 3.5 (0.1).5 (0.18) 5 (0.) 7 (0.8) 7 (0.8) (0.7) (0.87) 8 (1.10) 36 (1.) 0 (1.57) 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) ØN 3.5 (0.1) 3.5 (0.1) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) ØO 6.5 x 3.5 dp (0.6 x 0.1 dp) 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) 13.7 x 10.5 dp (0.5 x 0.1 dp).8 x 13.5 dp (0.66 x 0.53 dp).8 x 13.5 dp (0.66 x 0.53 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 1/8* 1/8* 1/* 1/* 3/8* 3/8* 7.0 (0.8) (0.3) 8. (0.33) 8.7 (0.3) 9. (0.36) 10.5 (0.1) 11.5 (0.5) 1.0 (0.55) 18.0 (0.71) 9.3 (1.9) 57.0 (.) 70.6 (.78) 83.6 (3.9) 10 (.09) 1.9 (.) Z.5 (0.65) 17.8 (0.70). (0.88). (0.88) 7.0 (1.06) 7.0 (1.06) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page 3

24 lobal Series Cylinders agnetic Piston Ø - Ø5 s Sensors must be ordered separately. See page 37. E 7 (.8) ØN THU () ØO C'OE () H TP ØT + STOE + STOE eed 5 (1.00) Elect. 19 (0.75) Dimensional Data Note 1- See page for complete stroke availability Note - Chart dimensions are shown as (inches) od flats (Dim. ) nominally in-line with ports 5 P PCES 5 (.) 5 (.) 8 (.3) 8 (.3) arning THIS CYINDE HS NON-OTTIN OD. TO PEVENT INTEN DE HOD OD Y FTS ONY HEN FUY ETCTED HIE INSTIN O EOVIN TTCHENTS. DO NOT SCTCH O DENT SHFT. size Nonrotating rod accuracy ± ±1 ±1 ±1 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 ± Stroke 9.0 (1.93) 6.5 (1.83) 8.5 (1.91) 5.0 (.13).5 (.) 75.0 (.95) ong Stroke.0 (1.65) 39.5 (1.56) 0.5 (1.59) 6.0 (1.81) 53.5 (.11).0 (.8) 8.7 (.3) 9. (.36) 10.5 (.1) 11.5 (.5) 1.0 (.55) 18.0 (.71) Stroke,, 5, 1 5, 1 5, 1 5, 1 5, 1 5, 1 Extended Stroke.3 (1.67).7 (1.76) 5.1 (.13) 60.5 (.38).8 (.51) 6.5 (.6) 67.3 (.65) 7.6 (.86) 79.5 (3.13) 88.7 (3.9) 38.8 (1.53) 1. (1.6) 9.6 (1.95) 55.5 (.19) 56.8 (.) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0) 8.9 (.35) 10. (.0).1 (.8).7 (.).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Note: 5 x 0.8 port will accept #10-3 male thread fittings. (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Stroke ange 5~30 (0.~1.18) 5~30 (0.~1.18) 5~ (0.~.0) 5~ (0.~.0) 5~ (0.~.0) 5~ (0.~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 36.5 (1.) 39.0 (1.5).0 (1.73) 5.5 (1.79) 9.0 (1.93) 6.5 (1.83) 8.5 (1.91) 5.0 (.13).5 (.) 75.0 (.95) 33.0 (1.30) 35.5 (1.0) 39.5 (1.56) 0.5 (1.59).0 (1.65) 39.5 (1.56) 0.5 (1.59) 6.0 (1.81) 53.5 (.11).0 (.8) 6 (0.36) 8 (0.315) (0.7) (0.0) (0.0) (0.787) (0.787) 5 (0.98) 30 (1.181) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) H (Threads) x dp minimum #8-3 x.1dp 3 x dp #8-3 x.1dp x dp #10-3 x.8 dp 5 x dp 1/-8 x.39 dp 6 x dp 5/- x. dp 8 x 1.5 dp 3/8- x. dp 8 x 1.5 dp 1/- x. dp 10 x 1.5 dp 1/- x. dp 10 x 1.5 dp 5/8-18 x.88 dp x.0 dp 3/- x.88 dp x.5 dp 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 58.9 (.3) 69 (.7) 8.9 (3.3) (.01) 9.8 (5.11) (6.06) Page 6--06

25 Ø3 Double cting, Non-otating Piston od odels H TP ØN THU HOE () ØO C'OE () 7 (0.8) eed 5 (1.00) Electronic 19 (0.75) P PCES Z ØT H TP Ø0- Ø s ØN THU HOE () ØO C'OE (8) Z 7 (0.8) P PCES ØT Slots () for ound Profile Sensors Slots () for ound Profile Sensors See page 37 for round profile sensors featuring surge suppression, polarity protection and dual output. + STOE + STOE 9 (.35) + STOE + STOE eed 5 (1.00) Electronic 19 (0.75) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () od flats (Dim. ) nominally in-line with ports ØT 15 +0/ 0.03 ( /0.00) +0/ 0.05 ( /0.00) 13 +0/ 0.03 (0.5 +0/0.00) 15 +0/ 0.03 ( /0.00) 1 +0/ 0.06 ( /0.00) 8 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 3 +0/ 0.06 ( /0.00) 59 +0/ 0.07 (.33 +0/0.003) 1.5 (0.059) 1.5 (0.059).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079) od end male thread J NUT INCUDED F H THEDS Tapped hole mounting Note: Inch threads for 'N' port code. etric threads for '' & 'P' port codes. etric for foot, flange, or clevis mount. O THED OTH ENDS F (HEX) inch or.3 or 8.3 or or 13.3 or 17. or.56 or.75 or 7.75 or 7.93 or or 6 H (THEDS) #8-3 x.31 lg or 5 x lg #8-3 x.31 lg or 6 x lg #10-3 x.31 lg or 8 x lg 1/-8 x.37 lg or 10 x lg 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg 1/- x.77 lg or 18 x lg 5/8-18 x 1.00 lg or x lg 3/- x 1. lg or 6 x lg inch or 0.5 or or or or or or or or or or O (THEDS) #8-3 or x 0.7 #8-3 or x 0.7 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 7/-1 or 10 x 1.5 1/-13 or x /-13 or x 1.75 Places Front F inch or 0. or 0. or 0.98 or or or or 1.13 or or 9 Places ear inch or 0.3 or or or 1.13 or or 9 5. (0.) 6 (0.) 1 (0.55) 1 (0.55) 18 (0.71) 18 (0.71) (0.87) 7 (1.06) 3.5 (0.1) 3.5 (0.1).5 (0.18) 5 (0.) 7 (0.8) 7 (0.8) (0.7) (0.87) 8 (1.10) 36 (1.) 0 (1.57) 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) ØN 3.5 (0.1) 3.5 (0.1) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) ØO 6.5 x 3.5 dp (0.6 x 0.1 dp) 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) 13.7 x 10.5 dp (0.5 x 0.1 dp).8 x 13.5 dp (0.66 x 0.53 dp).8 x 13.5 dp (0.66 x 0.53 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 1/8* 1/8* 1/* 1/* 3/8* 3/8* 7.0 (0.8) (0.3) 8. (0.33) 8.7 (0.3) 9. (0.36) 10.5 (0.1) 11.5 (0.5) 1.0 (0.55) 18.0 (0.71) 9.3 (1.9) 57.0 (.) 70.6 (.78) 83.6 (3.9) 10 (.09) 1.9 (.) Z.5 (0.65) 17.8 (0.70). (0.88). (0.88) 7.0 (1.06) 7.0 (1.06) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page 5

26 lobal Series Cylinders agnetic Piston arning Ø - Ø5 s THIS CYINDE HS NON-OTTIN OD. TO PEVENT INTEN DE HOD OD Y FTS ONY HEN FUY ETCTED HIE INSTIN O EOVIN TTCHENTS. DO NOT SCTCH O DENT SHFT. Sensors must be ordered separately. See page 37. E 7(.8) ØN THU () ØO C'OE () + ( x STOE) + STOE + STOE eed 5 (1.00) Elect. 19 (0.75) ØT H TP OTH ENDS P PCES Dimensional Data Note 1- Note - See page for complete stroke availability Chart dimensions are shown as (inches) od flats (Dim. ) nominally in-line with ports 5 5 (.) 5 (.) 8 (.3) 8 (.3) size Nonrotating rod accuracy ± ±1 ±1 ±1 ±0.8 ±0.8 ±0.8 ±0.8 ±0.8 ± Stroke 70.8 (.79) 69.5 (.7) 75.3 (.96).6 (3.17) 89.5 (3.5).7 (3.96) ong Stroke 56.8 (.) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) Stroke,, 5, 1 5, 1 5, 1 5, 1 5, 1 5, 1 Extended Stroke 38.8 (1.53) 1. (1.6) 9.6 (1.95) 55.5 (.19) 56.8 (.) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0) 5.8 (1.) 8. (1.90) 58.6 (.31) 65.5 (.58) 70.8 (.79) 69.5 (.7) 75.3 (.96).6 (3.17) 89.5 (3.5).7 (3.96) 8.9 (.35) 10. (.0).1 (.8).7 (.).7 (.).7 (.) 13. (.5) 18.5 (.73) 1.0 (.55) 18.0 (.71) odel Code '' Hole Size N (N) 1.5 (.06) 1.5 (.06) (.13) (.13) (.13).0 (.).0 (.) 6.3 (.5) 6.3 (.5) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Stroke ange 5~30 (0.~1.18) 5~30 (0.~1.18) 5~ (0.~.0) 5~ (0.~.0) 5~ (0.~.0) 5~ (0.~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0) 10~ (0.39~.0). (1.75) 8.0 (1.89) 55.0 (.17) 57.0 (.).5 (.) 6.0 (.5) 66.5 (.6) 68.0 (.68) 81.0 (3.19) 9.5 (3.7) 37. (1.7) 1.0 (1.61) 6.0 (1.81) 7.0 (1.85) 9.5 (1.95).0 (1.97).5 (1.99) 5.0 (.05) 61.0 (.0) 70.5 (.78) 6 (0.36) 8 (0.315) (0.7) (0.0) (0.0) (0.787) (0.787) 5 (0.98) 30 (1.181) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) H (Threads) x dp minimum #8-3 x.1dp 3 x dp #8-3 x.1dp x dp #10-3 x.8 dp 5 x dp 1/-8 x.39 dp 6 x dp 5/- x. dp 8 x 1.5 dp 3/8- x. dp 8 x 1.5 dp 1/- x. dp 10 x 1.5 dp 1/- x. dp 10 x 1.5 dp 5/8-18 x.88 dp x.0 dp 3/- x.88 dp x.5 dp 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 58.9 (.3) 69 (.7) 8.9 (3.3) (.01) 9.8 (5.11) (6.06) Page

27 Double cting, Double od, Nonrotating Piston od odels Ø3 H TP OTH ENDS ØN THU HOE () ØO C'OE () Z Slots () for ound Profile Sensors 7 (0.8) od flats (Dim. ) nominally in-line with ports * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Note: 5 x 0.8 port will accept #10-3 male thread fittings F (HEX) inch or.3 or 8.3 or or 13.3 or 17. or.56 or.75 or 7.75 or 7.93 or or 6 ØT eed 5 (1.00) Electronic 19 (0.75) P PCES 9 (.35) + STOE + STOE + ( x STOE) See page 37 for round profile sensors featuring surge suppression, polarity protection and dual output. (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Ø0- Ø s ØT 15 +0/ 0.03 ( /0.00) +0/ 0.05 ( /0.00) 13 +0/ 0.03 (0.5 +0/0.00) 15 +0/ 0.03 ( /0.00) 1 +0/ 0.06 ( /0.00) 8 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 3 +0/ 0.06 ( /0.00) 59 +0/ 0.07 (.33 +0/0.003) od end male thread H THEDS Tapped hole mounting Note: Inch threads for 'N' port code. J NUT INCUDED etric threads for '' & 'P' port codes. etric for foot, flange, or F + STOE clevis mount. H (THEDS) #8-3 x.31 lg or 5 x lg #8-3 x.31 lg or 6 x lg #10-3 x.31 lg or 8 x lg 1/-8 x.37 lg or 10 x lg 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg 1/- x.77 lg or 18 x lg 5/8-18 x 1.00 lg or x lg 3/- x 1. lg or 6 x lg inch or 0.5 or or or or or or or or or or 3.5 ØN THU HOE () ØO C'OE (8) H TP OTH ENDS O (THEDS) #8-3 or x 0.7 #8-3 or x 0.7 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 7/-1 or 10 x 1.5 1/-13 or x /-13 or x 1.75 Z 7 (0.8) Slots () for ound Profile Sensors P PCES Places Front ØT F inch or 0. or 0. or 0.98 or or or or 1.13 or or 9 + STOE eed 5 (1.00) Electronic 19 (0.75) + ( x STOE) Places ear 1.5 (0.059) 1.5 (0.059).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079) O THED OTH ENDS + STOE inch or 0.3 or or or 1.13 or or 9 5. (0.) 6 (0.) 1 (0.55) 1 (0.55) 18 (0.71) 18 (0.71) (0.87) 7 (1.06) 3.5 (0.1) 3.5 (0.1).5 (0.18) 5 (0.) 7 (0.8) 7 (0.8) (0.7) (0.87) 8 (1.10) 36 (1.) 0 (1.57) 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) ØN 3.5 (0.1) 3.5 (0.1) 5.5 (0.) 5.5 (0.) 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) ØO 6.5 x 3.5 dp (0.6 x 0.1 dp) 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) 13.7 x 10.5 dp (0.5 x 0.1 dp).8 x 13.5 dp (0.66 x 0.53 dp).8 x 13.5 dp (0.66 x 0.53 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 1/8* 1/8* 1/* 1/* 3/8* 3/8* 7.0 (0.8) (0.3) 8. (0.33) 8.7 (0.3) 9. (0.36) 10.5 (0.1) 11.5 (0.5) 1.0 (0.55) 18.0 (0.71) 9.3 (1.9) 57.0 (.) 70.6 (.78) 83.6 (3.9) 10 (.09) 1.9 (.) Z.5 (0.65) 17.8 (0.70). (0.88). (0.88) 7.0 (1.06) 7.0 (1.06) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page 7

28 lobal Series Cylinders agnetic Piston Precision Stroke djustment Emphasizing Operator Safety Full stroke adjustment on all strokes. agnetic piston is a standard feature. pply sensors (ordered separately) to dovetail or round slots for mid-stroke and end-of-stroke sensing. djustable Extend Stroke Cylinders Fabco-ir's popular Dial--Stroke adjustment assembly is now available on lobal Series Cylinders to provide a rugged, precision adjustment of the cylinder extend stroke. Cylinders are offered in double acting models in bore sizes of 3 through with full stroke adjustment. agnetic pistons are included for use with any of the electronic or reed sensors. Sensors must be ordered separately. See page 37. Operator Safety The stop tube, adjustment nut with skirt, and minimum clearances combine to eliminate pinch points. Note - Chart dimensions are shown as (inches) Dimensional Data Construction The stop tube is black anodized aluminum the adjustment nut is blackened steel with a black anodized aluminum skirt the stop flange is red anodized aluminum: all for corrosion resistance and appearance. The adjustment nut, steel for long life, includes a lock screw with a plastic plug so the adjustment nut can be locked in place without damaging the threads. Precision adjustment is achieved with fine pitch threads on the adjustment rod. The stop flange is mounted on the end of the adjustment rod so the nut will not come off. djustment djustment settings are simplified by the convenient scale markings. s 3 and 0 have a 1/- thread giving.0" (1.3) adjustment per nut revolution. s and larger have a 3/- thread giving.0" (1.6) adjustment per revolution. How to Order (See page 9 - model codes & ; see page 9 - mounting codes.) Example 1: To order a bore, 75 stroke unit with Dial-a-Stroke, NPT ports, and rod end tap mount, specify odel No. ND0075D Example : lso available with nonrotating rod; use body length '' dimension from page 6, tapped hole mounting information from page 7 and insert the non-rotating rod Code '' in model number. To order bore, 75 stroke, nonrotating rod, with Dial-a- Stroke, NPT ports, and ISO flange specify odel No. ND0075D Note hen ordering units with flange or foot mounts, the rod stickout (Dim. "") increases per dimension on pages 31 or 3. OE 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () STOE 15, 5, 0.5 (1.59).0 (1.97).5 (1.99) 5.0 (.05) 61.0 (.0) 70.5 (.78), 5, (1.88) 55.5 (.19) 59.3 (.33) 6.6 (.5) 69.5 (.7) 76.7 (3.0) (0.0) (0.0) (0.787) (0.787) 5 (0.98) 30 (1.181).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) H (THEDS) 5/- x.5 dp 8 x dp 3/8- x.7 dp 8 x dp 1/- x.69 dp 10 x 1.5 dp 1/- x.69 dp 10 x 1.5 dp 5/8-18 x.96 dp x.0 1dp 3/- x 1.06 dp x.5 30 dp 58.9 (.3) 69.0 (.7) 8.9 (3.3) (.01) 9.8 (5.11) (6.06) 1 (0.55) 1 (0.55) 17 (0.67) 17 (0.67) (0.87) 7 (1.06) 7 (0.8) 7 (0.8) 10(0.39) (0.7) 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) Page

29 Dial--Stroke djustable Extend Stroke odels Ø3 - Ø s H THEDS Standard mounting Code "" Tapped Holes places useable at rod end only. lso includes thru holes ØN w/c'bore ØO Optional mounting See How to Order note page 8. Code "E" Front Flange Code "" ISO Front Flange Code "" Foot ount Note!! Use caution when mounting to avoid creating pinch points with other parts of your machinery 7 (0.8) eed 5 (1.00) Electronic19 (0.75) T lso available with Nonrotating rod. See page 8 example. Sensors must be ordered separately. See page 37. STOE Z ØS FTS od end male thread OE 3 0 ØN 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) F (HEX) inch or. or.56 or.75 or 7.75 or 7.93 or or 6 J NUT INCUDED F ØO 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 11.0 x 8.0 dp (0.3 x 0.31 dp) 13.7 x 10.5 dp (0.5 x 0.1 dp).8 x 13.5 dp (0.66 x 0.53 dp).8 x 13.5 dp (0.66 x 0.53 dp) *P 1/8* 1/8* 1/* 1/* 3/8* 3/8* H (THEDS) 5/- x. lg or 1 x lg 3/8- x. lg or 1 x lg 1/- x.77 lg or 18 x lg 1/- x.77 lg or 18 x lg 5/8-18 x 1.00 lg or x lg 3/- x 1. lg or 6 x lg H THEDS inch or 0.78 or or or or or or 3.5 STOE 15, 5,, 5, (0.3).7 (0.) 9. (0.36).7 (0.) 10.5 (0.1) 13. (0.5) 11.5 (0.5) 18.5 (0.73) 1.0 (0.55) 1.0 (0.55) 18.0 (0.71) 18.0 (0.71) + STOE Note: Inch threads for 'N' port code. etric threads for '' & 'P' port codes. etric for foot, flange, or clevis mount. Tapped hole mounting (1.6) 1.1 (1.6) 53.6 (.11) 5.6 (.07) 56.6 (.3) 65.1 (.56) F O (THEDS) 1/- or 6 x 1.0 1/- or 6 x 1.0 5/-18 or 8 x 1.5 7/-1 or 10 x 1.5 1/-13 or x /-13 or x 1.75 ØS 38 (1.5) 38 (1.5).8 (.0).8 (.0).8 (.0).8 (.0) O THED T 7.6 (.30) 7.6 (.30).0 (.7) 11.0 (.3) 15.0 (.59) 15.0 (.59) P PCES + ( x STOE) F inch or 0.87 or 1.13 or or (1.9) 57.0 (.) 70.6 (.78) 83.6 (3.9) 10 (.09) 1.9(.) * Port Size Offerings See dim. column P below N NPT ports, inch rod thread SP parallel ports, metric rod thread P SPT taper ports, metric rod thread Z.5 (0.65) 17.8 (0.70). (0.88). (0.88) 7.0 (1.06) 7.0 (1.06) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Page 9

30 lobal Series Cylinders ear Clevis ount Ø - Ø5 s T Ø Pin N OT PCES C CU CX CZ Ø3 - Ø s Note: ll clevis mounts attach to cylinder body with metric size socket cap screws T Ø Pin Note: Pin diameter will be inch size for cylinders with port code 'N' and size for cylinders with port code '' or 'P'. N OT PCES N OT x0.7 x0.7 6x1.0 6x1.0 6x1.0 6x1.0 8x1.5 10x1.5 x1.75 x1.75 CU CX C CZ ear Clevis ount Dimensions (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () Ø Pin Nominal or inch 5 or or or.3 10 or or or or.0 1 or.0 18 or.7 or.875 C 1 (0.55) 15 (0.59) 18 (0.71) (0.79) (0.79) (0.87) 8 (1.10) 30 (1.18) 38 (1.) 5 (1.77) CU 7.0 (0.8) (0.7) 1 (0.55) 1 (0.55) 1 (0.55) (0.79) (0.79) 7 (1.07) 31 (1.) CX 5.3 (0.1) 6.8 (0.7) 8.3 (0.33) 10.3 (0.1) 18.3 (0.7) 18.3 (0.7).3 (0.88).3 (0.88) 8.3 (1.11) 3.3 (1.7) CZ (0.7) (0.) (0.79) 36 (1.) 36 (1.) (1.73) (1.73) 56 (.) 6 (.5) T 5 (0.) 5 (0.) 5 (0.) 5 (0.) 6 (0.) 11 (0.3) 1 (0.55).8 (0.11).8 (0.11).0 (0.).0 (0.).0 (0.).0 (0.) 5.0 (0.) 6.0 (0.) 7.0 (0.8) 7.0 (0.8) 6.0 (0.) 6.0 (0.) 9.0 (0.35) 1 (0.55) 1 (0.55) 18 (0.71) (0.87) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57).5 (1.75) 5 (.05).7 (.51) 76.7 (3.0) 97.8 (3.85) (.5) Page

31 Foot ounts Ø - Ø5 s N OT PCES T Double od +Stroke Y H X Z X Y D PCES T Y X Ø3 - Ø s Note: ll feet attach to cylinder body with metric size socket cap screws T H Y N OT PCES N OT x0.7 x0.7 6x1.0 6x1.0 6x1.0 6x1.0 8x1.5 10x1.5 x1.75 x1.75 X Z D PCES Foot ount Dimensions X Y T Y X (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () D.5 (0.18).5 (0.18) 6.6 (0.6) 6.6 (0.6) 6.6 (0.6) 6.6 (0.6) 9.0 (0.35) 11 (0.3) 13 (0.51) 13 (0.51) H 17 (0.67) 19 (0.75) (0.9) 6 (1.0) 30 (1.18) 33 (1.30) 39 (1.5) 6 (1.81) 59 (.3) 71 (.) X 3 (1.3) 38 (1.) 8 (1.89) 5 (.05) 57 (.) 6 (.5) 79 (3.11) 95 (3.7) 118 (.65) 137 (5.39) Y 9.5 (1.) 33.5 (1.3).0 (1.65) 6.0 (1.81) 57.0 (.) 6.0 (.5) 78.0 (3.07) 91.5 (3.60) 11 (.9) 136 (5.35) Z (1.73) 8 (1.89) 6 (.) 66 (.60) 71 (.) 78 (3.07) 95 (3.7) 113 (.5) 10 (5.51) (6.38) 13.5 (0.53) 13.5 (0.53) 1.5 (0.57) 15 (0.59) 17 (0.67) 17 (0.67) 18 (0.71) 18 (0.71) (0.79) (0.87) T (0.08) (0.08) 3. (0.13) 3. (0.13) 3. (0.13) 3. (0.13) 3. (0.13) 3. (0.13).5 (0.18) 6.0 (0.) X 9. (0.36) 10.7 (0.) 11. (0.) 11. (0.) 1.7 (0.58). (0.6) 19.5 (0.77) 3 (0.91) Y.5 (0.18) 5.0 (0.) 5.8 (0.3) 5.8 (0.3) 5.8 (0.3) 7.0 (0.8) 8.0 (0.31) 9.0 (0.35) 11.0 (0.3).5 (0.9).8 (0.11).8 (0.11).0 (0.).0 (0.).0 (0.).0 (0.) 5.0 (0.) 6.0 (0.) 7.0 (0.8) 7.0 (0.8) Page 31

32 lobal Series Cylinders Flange ounts Front Flange Ø - Ø5 s N olt Places FT FV FD Places FX FZ ear Flange Ø - Ø5 s FV FD Places N olt Places FT FX FZ Note: ll flanges attach to cylinder body with metric size flat head socket screws ear Flange Ø3 - Ø s N olt Places FX FZ Front Flange Ø3 - Ø s N olt Places FY FV FD Places Flange ount Dimensions FT FD 5.5 (0.) 5.5 (0.) 6.6 (0.6) 6.6 (0.6) 7 (0.8) 9 (0.35) 9 (0.35) 9 (0.35) (0.7) 1 (0.55) FT FD Places FX FZ ISO ectangular Flange Dimensions FY 3 (1.6) 36 (1.) 5 (1.77) (1.97) (.8) 75 (.95) FX 0 (1.57) 0 (1.57) (1.97) (1.97) 6 (.5) 7 (.83) 90 (3.5) (3.9) 6 (.96) 1 (5.91) FV 5 (0.98) 30 (1.18) 39 (1.5) (1.65) 8 (1.89) 5 (.13) 67 (.6) (3.15) 99 (3.90) 117(.61) FZ (1.97) (1.97) 6 (.) 6 (.) 76 (.99) 88 (3.7) 106 (.17) 1 (.57) 1 (5.91) 178 (7.01) FY FV (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () FT 5.5 (0.) 5.5 (0.) 9 (0.35) 9 (0.35) 11 (0.3) 11 (0.3) Coon Dimensions 8.0 (0.31) 8.0 (0.31) 6.5 (0.6) 7.0 (0.8) 9.0 (0.35) 9.0 (0.35) 9.0 (0.35) 9.0 (0.35) 9.0 (0.35) 11 (0.3) N olt x 0.7 x x x x x x x 1.5 x 1.75 x 1.75 FD.5 (0.18).5 (0.18) 6.6 (0.6) 6.6 (0.6) 5.5 (0.) 5.5 (0.) 6.6 (0.6) 9 (0.35) 11 (0.3) 11 (0.3) Interchange (Non-ISO) Flange Dimensions FY 3 (1.3) 0 (1.57) (1.97) 60 (.36) 77 (3.03) 9 (3.70) FX 5 (1.77) 5 (1.77) 8 (1.89) 5 (.05) 56 (.) 6 (.) 76 (.99) 9 (3.6) 1(.57) 136(5.35) FV 5 (0.98) 30 (1.18) 39 (1.5) (1.65) 8 (1.89) 5 (.13) 67 (.6) (3.15) 99 (3.90) 117(.61) FZ 55 (.17) 55 (.17) 60 (.36) 6 (.5) 65 (.56) 7 (.83) 89 (3.) 108 (.5) 13 (5.8) 15 (6.06) Page

33 Front & ear oss ounts ear oss Ø - Ø5 s Front oss Ø - Ø5 s ØT ØT ear oss Ø3 - Ø s Front oss Ø3 - Ø s ØT ØT oss ount Dimensions (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () ØT 15 +0/ 0.03 ( /0.00) +0/ 0.05 ( /0.00) 13 +0/ 0.03 (0.5 +0/0.00) 15 +0/ 0.03 ( /0.00) 1 +0/ 0.06 ( /0.00) 8 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 35 +0/ 0.06 ( /0.00) 3 +0/ 0.06 ( /0.00) 59 +0/ 0.07 (.33 +0/0.003) 1.5 (0.059) 1.5 (0.059).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079).0 (0.079) Page 33

34 lobal Series Cylinders ack-to-ack Cylinders Option XC10 Note 1: vailable double acting only Note : agnetic piston body style "D" includes magnet in both cylinder sections ack-to-back cylinders are for use where three or four rod positions are required. Two cylinders are assembled back-to-back with bolts threaded into tapped end mounting holes. Different strokes on each cylinder enable having four positive stop positions when the units are mounted at the rod ends. ack-to-back cylinders provide independent piston rods on each end of the unit. To order specify the desired strokes with a slash between the 3- digit stroke codes, then follow model number with option suffix XC10 Tie bolts are used in all holes Consult factory to confirm total body length 1. Ordering Example lobal Series, NPT ports, magnetic piston, 0 bore, dual strokes of 30 and, bumpers both ends and male rod ends. The odel Number is: ND S / 0D XC10. non-rotating rod can be fitted to one section. The position of "" model code determines the stroke of the non-rotating rod cylinder section. Example: NN S00 030/0D XC10 "S" Indicates 30 stroke single rod "" indicates stroke non-rotating rod Tandem Cylinders Option XC11 & XC Note: vailable double acting only XC11 ounting: Code '' tapped holes at rod end. Code 'E' or '' flange optional XC ounting: Code '' tapped holes at cap end. Code 'F' or 'H' flange optional (Tie rods are then fastened from the front) Tandem cylinders are generally used when three distinct rod positions are required. Two cylinders are assembled tip-to-tail with bolts threaded into the rear tapped mounting holes of the forward cylinder. Using cylinders with two different strokes (the shorter located on the rear cylinder), enables a single rod to be extended to a positive midposition or to full extension. To order specify the desired strokes with a slash between the 3-digit stroke codes, then follow model number with option suffix XC11 or XC Note: ore than three positions can be obtained by assembling multiple cylinders together. Please consult the factory for these special requirements. T T1 hen a single magnetic piston is ordered, it is applied in the forward cylinder Ordering Example lobal Series, SPT ports, with single magnetic piston, bore, dual strokes of 75 and, and male rod thread. The odel Number is: PD S0 075/D XC11 hen magnets and bumpers are required in both forward and rear cylinders, and tapped holes are required at cap end, order as PDD S0 075 /D XC T Consult factory to confirm total body length T1 Page

35 Cylinder Options and Universal Seal its Position pplication 1 djustable etract Stroke Option S vailable on s and arger Thread sealing locknut 3 djusting screw Pressure applied to piston Open to atmosphere n adjusting screw with a thread sealing locknut mounted in a thick rear cover provides a simple, yet rugged adjustment of the cylinder stroke in the retract direction. The fine thread of the adjusting screw provides precision adjustment. s, 5 and 3 have a 5/- thread giving.0" (1.1) adjustment per revolution. s 0 thru have a 1/- thread giving.0" (1.3) adjustment. The adjustable retract stroke option is available on bores and larger for any stroke. Standard adjustment is up to and including 5. For over 5 adjustment specify adjustment length after the option designation S. Example: for adjustment the option designation becomes S- 3 Position pplication Viton Seals Option V For elevated temperatures from 6C to C (-15F to +00 F) or for compatibility with hostile media. Consult engineering for compatibility information. 3 1 Pressure applied to piston Open to atmosphere Universal Seal its For single and double rod cylinders and adjustable stroke models. Nonrotating rod seals are available separately. Seals for options are available on request Seal it una N Viton - S - SV - S - SV - S - SV 5 - S 5 - SV 3 - S 3 - SV 0 - S 0 - SV - S - SV - S - SV - S - SV - S - SV Non-otating od Seal una or Viton - DDS - 6V - DDS - 8V - DDS - 10V 5 - DDS - V 3 - DDS - V 3 - DDS - V - DDS - V - DDS - V - DDS - 5V - DDS - 30V 9--0 Page 35

36 lobal Series Cylinders ccessories od Eye To order a od Eye use the Prefix E followed by the thread size. Example: For a 5 bore cylinder the inch rod threads are 1/-8. The od Eye Part Number is /-8 For #8-3 size, follow with or for bore. Example: E U X Ø Hole ad. Note: Hole diameter will be inch size for items with inch thread and size for items with metric thread. Z (1/) (5/8) (3/) 5 (1) 3 0 (1-1/) (1-1/) () (-1/) (3-1/) () (0.) 5 (0.98) 5 (0.98) 30 (1.18) 30 (1.18) 30 (1.18) 0 (1.57) 0 (1.57) (1.97) 55 (.17) U 7.0 (0.7) 1.0 (0.55) 11.5 (0.5) 1.0 (0.55) 1.0 (0.55) 1.0 (0.55).0 (0.79).0 (0.79) 7.0 (1.06) 31.0 (1.) X.7 (0.18) 6. (0.) 7.7 (0.30) 9.7 (0.38) 17.6 (0.69) 17.6 (0.69) 1.6 (0.85) 1.6 (0.85) 7.6 (1.08) 31.6 (1.) Z 9.7 (0.38) 11. (0.) (0.) 19 (0.75) (0.87) (0.87) 7 (1.06) 7 (1.06) 38 (1.).5 (1.75) (0.) 6.0 (0.) 6.0 (0.) 8.0 (0.31) 1.0 (0.55) 1.0 (0.55) 18.0 (0.71) 18.0 (0.71) 1.0 (0.83) 1.0 (0.83) 1.5 (0.85) 3.0 (1.6) 3.0 (1.3) 1.0 (1.61).0 (1.65).0 (1.65) 56.0 (.) 56.0 (.) 71.0 (.) 79.0 (3.11) 6.3 (0.5).0 (0.7) 10.3 (0.1).8 (0.).0 (0.7).0 (0.7).0 (0.).0 (0.) 1.0 (0.83).0 (0.95) od Clevis 1 U Note: Pin diameter will be inch size for items with inch thread and size for items with metric thread. X P Z Ø PIN E (1/) (5/8) (3/) 5 (1) 3 0 (1-1/) (1-1/) () (-1/) (3-1/) () To order a od Clevis use the Prefix C followed by the thread size. Example: For a bore cylinder the metric threads are 18 x 1.5. The od Clevis Part Number is C18x1.5 For #8-3 size, follow with or for bore. Example: C-8-3- (0.) 1 (0.83) 5 (0.98) 30 (1.18) 30 (1.18) 30 (1.18) 0 (1.57) 0 (1.57) (1.97) 55 (.17) U X 7.0 (0.7) 5.3 (0.1) 10.0 (0.39) 6.6 (0.6) 11.5 (0.5) 8.3 (0.33) 1.0 (0.55) 10.3 (0.1) 1.0 (0.55) 18. (0.7) 1.0 (0.55) 18. (0.7).0 (0.79). (0.88).0 (0.79). (0.88) 7.0 (1.06) 8. (1.) 31.0 (1.) 3. (1.8) Z (0.7) (0.) (0.78) 36.6 (1.) 36.6 (1.).5 (1.75).5 (1.75) 55.6 (.19).5 (.) P E 1 (0.55) (0.) (0.7) 1 (0.83) (0.) 5 (0.98) (0.78) 1 (1.61) (0.87) 1 (1.61) (0.87) (1.97) 8 (1.10) (1.97) 8 (1.10) 6.5 (.6) 38 (1.) 70.6 (.78) (1.73) Ø Hole, Ø Pin Nominal inch or.187 or or 5.3 or or or or 10.0 or 1.0 or 1.7 or or (0.) 6.0 (0.) 6.0 (0.) 8.0 (0.31).0 (0.).0 (0.).0 (0.79).0 (0.79) 3.0 (0.91).0 (0.95) Threads #8-3 or 5 x 0.8 #8-3 or 6 x 1.0 #10-3 or 8 x 1.5 1/-8 or 10 x 1.5 5/- or 1 x 1.5 3/8- or 1 x 1.5 1/- or 18 x 1.5 1/- or 18 x 1.5 5/8-18 or x 1.5 3/- or 6 x (0.85) 8.0 (1.10) 3.0 (1.3) 1.0 (1.61).0 (1.65).0 (1.65) 56.0 (.) 56.0 (.) 71.0 (.) 79.0 (3.11) 6.3 (0.5).0 (0.7) 10.3 (0.1).8 (0.).0 (0.7).0 (0.7).0 (0.).0 (0.) 1.0 (0.83).0 (0.95) 8 Female Cordsets for uick Disconnect Sensors Sensor Pigtail 3 (1.3) 8.5 (.33) 1, or 5 eter Cable 3 (1.6) 9.8 (.39) lack ale Connector on Sensor lue () rown (+) Cordset Description 1 eter, 3 Pin eters, 3- Pin 5 eters, 3- Pin eters, - Pin 5 eters, - Pin rown lack Part No. CFC-1 CFC- CFC-5 CFC- CFC-5 Female Connector on Cordset lue Page

37 NE ow Profile Sensors for agnetic Piston Cylinders 3/8" & 1/" Dovetail Sensors Installation for 3/8" Dovetail Sensors Ordering uide 3/8" Dovetail 1/" Dovetail ounting clamp Sensor (eed Switch shown) 1 Insert the mounting clamp into one of the dovetail slots and slide it to the approximate location desired. Position the sensor with its set screw facing the mounting clamp. Sensor Type eed (No ED) eed (ED) Electronic (ED) Electronic (ED) eed (No ED) eed (ED) Electronic (ED) Electronic (ED) Encased in a plastic housing, dovetail style sensors are corrosion resistant. 60 wire outlet allows close mounting. Sensors are mounted in dovetail slots in the wall of the cylinder and are actuated by a magnetic piston. agnetic pistons are specified with ody Code "D" in the lobal Series Cylinder model number. Two types of sensors are offered: eed Switches and Electronic Sensors. Sensors must be ordered separately from the tables below. Each sensor is furnished complete with a set screw for secure installation. ounting clamp included with 99-0-xxx models for 3/8" dovetail. 1 3 These models are NOT polarity protected. e sure to follow hook up instructions Electrical Characteristics 0-0 VDC/VC, 0.5 mp ax current, 10 att ax, 0 Voltage Drop 5-0 VDC/VC, 0.03 mp ax current, att ax,.0 Voltage Drop Sourcing PNP 6- VDC, 0. mp ax current, 0.5 Voltage Drop Sinking NPN 6- VDC, 0. mp ax current, 0.5 Voltage Drop 0-0 VDC/VC, 0.5 mp ax current, 10 att ax, 0 Voltage Drop 5-0 VDC/VC, 0.03 mp ax current, att ax,.0 Voltage Drop Sourcing PNP 6- VDC, 0. mp ax current, 0.5 Voltage Drop Sinking NPN 6- VDC, 0. mp ax current, 0.5 Voltage Drop Set screw should be flush with the top surface of sensor. Push the sensor into its mounting clamp. Slide this assembly to the point of desired actuation. 3 Tighten the set screw to lock sensor in place.. ire eads Prewired 9 ft. Part No uick Disconnect Part No. * ound Profile Sensors Ordering uide ound Profile Sensors feature surge supression, polarity protection, ED indicator, and extremely fast switching speeds. These slide into mating keyhole slots adjacent to the cylinder port, and are easily positioned and locked in place with a set screw. ll round profile sensors feature surge supression, polarity protection, ED indicator, and extremely fast switching speeds. Sensor Type eed Switch for PC's w/ed (current limiting) Electronic ED and Sourcing Electronic ED and SInking Electronic ED & Dual Output Sinking or Sourcing ED Indicator ound Profile Sensors Electrical Characteristics Function SPST Normally Open PNP Normally Open NPN Normally Open Normally Open NPN or PNP Output Switching Voltage 5-0V C/DC /60 Hz 6-30 VDC 6-30 VDC 6-30 VDC Switching Current 0.0 mp max mp min. 0. mp max. 0. mp max. 0. mp max. Switching Power atts max. 6 atts max. 6 atts max. 6 atts max to center of Sensing rea for eed Style 7.0 to center of Sensing rea for Electronic Style ED Indicator.5 eed Style 5.8 Electronic Style Note*: uick Disconnect styles are supplied with 6 inch pigtail with male connector. Order female cordsets separately. See page 36. ø3.8 Switching Speed 0.5 ms operate 0.1 ms release 1.5µs operate 0.5µs release 1.5µs operate 0.5µs release 1.5µs operate 0.5µs release Voltage Drop.5 Volts 1.5 Volts 1.5 Volts 1.5 Volts 6 in. 8 ale uick Disconnect * 5 Prewired 9 ft. Part No. 9C C C C ft. Part Numbers uick Disconnect Part No.* 9C equires 3 pin cordset 9C equires 3 pin cordset 9C equires 3 pin cordset 9C equires pin cordset Temperature ange for Sensors - to + C (- to +176 F) rown (DC +) (DC ) lue eed Switch without ED rown (DC +) (DC ) lue eed Switch with ED rown VDC lack (+) () OD lue Electronic Sensor Sourcing rown VDC lack lue (+) () Electronic Sensor Sinking OD Page 37

38 lobal Series Cylinders Ø - Ø5 s Standard Features Chrome plated, stainless steel guide shafts with Duralon linear bearings tapped mounting holes on toolplate clearance holes (all sizes except 0) models requiring screw head clearance are c'bored as pictured bore holes tapped at rear - 5 bores holes c'bored and tapped at rear nodized aluminum toolplate 3 styles available: lank etric Inch lobal Series cylinder body Ø3 - Ø s Standard Features Chrome plated, stainless steel guide shafts with Duralon linear bearings clearance holes models requiring screw head clearance are c'bored as pictured tapped mounting holes on toolplate nodized aluminum toolplate 3 styles available: lank etric Inch lobal Series cylinder body 3 - bores clearance holes thru, c'bored each end, tapped each end Page

39 T Series Double cting, uided Toolplate odels How to Order T lobal Series uided Toolplate N without magnetic piston D with magnetic piston Sensors & cables must be ordered separately. Please see page thru 1 See data chart below for available standard strokes T odel Number Series Port ody Stroke Options N NPT ports and inch mounting holes in toolplate & cylinder SP Parallel ports and metric mounting holes in toolplate & cylinder P SPT taper ports and metric mounting holes in toolplate & cylinder 10 bore sizes: 0 thru umpers V Viton Seals T1 lank toolplate ODEIN EXPES TND 0 05 V uided toolplate, NPT ports, inch mounting holes in toolplate and cylinder, magnetic piston, bore, 5 stroke, Viton seals. (Sensors must be ordered separately. See page 37.) TN 05 0 uided toolplate, SP Parallel ports, metric mounting holes in toolplate and cylinder, 5 bore, stroke, no options. Engineering Data See page 8 for additional specifications 5 (.) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () 3.5 (7.8).99 (11) 7.7 (17) 8.17 (18) () 11. (6) (1/) (5/8) (3/) 5 (1) 3 (1-1/) 0 (1-1/) () (-1/) (3-1/) () 0 (1.57).36 (5.). (5.5) 3.1 (7.5) 3.68 (8.1) 8. (19) 10. (3).3 (5).5 (9) aximum llowable oad at Toolplate g. (bs) Standard vailable Cylinder Strokes (inch) 10 (.39) 15 (.59) (.79) 5 (.98).7 (6) 1.36 (3) 1.1 (.5) 0.95 (.1).09 (9).13 (.7) 1.86 (.1) 1.5 (3.) 7.6 ().99 (11).09 (9) 3.18 (7) 7.9 (.5) 5.5 ().77 (10.5).09 (9) 9.08 () 7.0 (15.5) 6.13 (13.5).99 (11) 9.99 () 7.7 (17) 6.5 (1.) 5.31 (11.7) (3.5) 1.07 (31).71 (8) (5) 5. (56).70 () 1.11 (6.5) 17.5 (38) (85) 35.8 (78.9) 33.1 (73) (68).00 (9.5) (85) (79) (7) aximum llowable oad at Toolplate g. (bs) Standard vailable Cylinder Strokes (inch) 5 (1.77) (1.97) 75 (.95) (3.9) 0. (1.1) 0.1 (0.9) 0.3 (0.7) 0.77 (1.7) 0.6 (1.) 0.1 (0.9).7 (5).09 (.6) 1.3 (.7) 0.77 (1.7).36 (5.).18 (.8) 1.3 (.9) 0.86 (1.9) 3.7 (7.) 3.0 (6.7).5 (5.) 1.91 (.) 3.5 (7.8) 3. (7.1). (5.8).09 (.6) 7.6 () 5.90 (13).81 (10.6).13 (9.1) 8.85 (19.5) 8.0 (18.5) 6. (1.6) 5.9 (.1). (37) 1.98 (33).08 (6.6) 10.6 (.6) (39) (35) (9) (.6) (1.18) 0.86 (1.9) 1.3 (.9).81 (6.) 3.1 (7.5).5 (10).81 (10.6) 10. (3) 1.98 (33) 8.60 () (69) 5 (.9) 0.73 (1.6) 0.86 (1.9) 1.36 (3).0 (.5) 3.81 (8.).13 (9.1) 35 (1.38).59 (5.7).7 (6) 3. (8) 3.90 (8.6) 9.99 () (9) 6.79 (59) 9.51 (65) 1 (5.91) 0.1 (0.9) 0.5 (1.) 1.0 (.3) 1.1 (3.1). (5.8).86 (6.3) Page 39

40 lobal Series Cylinders Ø Ø5 s Standard Toolplate Inch threads will be provided when 'N' port code is specified. etric threads will be provided when '' or 'P' port code is specified. 'S' Thru Hole 'U' Dia. C' by 'Y' Deep Places From Other Side Sensors for magnetic piston position indication must be ordered separately. See page 37. FF F C 'J' Tapped Thru Places Dimensional Data FF F C 5 Toolplate & ounting Inch Dimensions Specified by Port Code 'N' C F FF J OT /- 1/- T S U.8 Y.06 Toolplate & ounting etric Dimensions () Specified by Port Code '' or 'P' 5 C F FF J 3 x 0.5 x 0.7 x 0.7 x 0.7 OT x 0.7 x x x 1.0 T S U Y 5 ' ' Dimensions by and Stroke for both Standard & agnetic Piston shown as (inches) (1.30) 35.5 (1.0) 36.5 (1.) 37.5 (1.8) (1.) 0.5 (1.59) 1.5 (1.).5 (1.67) (1.69) 5.5 (1.79) 6.5 (1.83) 7.5 (1.87) 8.0 (1.89).5 (1.99) 51.5 (.03) 5.5 (.07) Stroke (.07) 55.5 (.19) 56.5 (.) 57.5 (.6) (.8) 60.5 (.38) 61.5 (.) 6.5 (.6) (.6) 67.5 (.66) (.81) 7.5 (.85) (3.01) 77.5 (3.05) Page

41 T Series uided Toolplate odels Dimensions Cylinder ody Tapped Hole ounting * Port Size Offerings Duralon earings T 'OT' Threads This End Only Inch threads will be provided when 'N' port code is specified. etric threads will be provided when '' or 'P' port code is specified. Note: 5 x 0.8 port will accept #10-3 male thread fittings lank Toolplate Use Option Code T1 to specify a blank toolplate shown below. T *E I Dia. C C * Note: See page for additional cylinder body angle and profile dimensions. P Places 'O' C' 'OT' Tapped ounting Hole x 'T' Deep Places 5 6 (0.36) 8 (0.315) (0.7).8 (0.188) 5 (0.197) 6 (0.36) 6 (0.36) 5 (0.98) 9 (1.1) 36 (1.) 0 (1.57) Chart Dimensions shown as (inches) E 3 (0.90) 7. (1.07) 31. (1.3) 36.9 (1.5) I 31.5 (1.) 37.1 (1.6) 7 (1.85) 51.3 (.0) 3.5 (0.1) 3.5 (0.1).5 (0.18) 5 (0.) (0.87) 8 (1.10) 36 (1.) 0 (1.57) O 6.5 x 3.5 dp (0.6 x 0.1 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) 9.0 x 7.0 dp (0.35 x 0.8 dp) *P 5x0.8 5x0.8 5x0.8 5x0.8 T 6.1 (.) 6.1 (.) 6.9 (.7) 8.3 (.33) 83.8 (3.30) 86. (3.39) 81.5 (3.1) 8.5 (3.5) (.8) 111. (.38) 1.6 (.59).5 (.8) (5.7) 136. (5.36) 11.6 (5.57) 17.5 (5.81) 5 Port ocation by & Stroke Stroke (0.8) 8.9 (0.35) 8.9 (0.35) (0.0) 10. (0.0) 8.1 (0.3) 8.1 (0.3).1 (0.8) 8. (0.33) 8. (0.33).7 (0.) (0.35) 10. (0.0).1 (0.8).7 (0.) Page 1

42 lobal Series Cylinders Ø3 Ø s Standard Toolplate Inch threads will be provided when 'N' port code is specified. etric threads will be provided when '' or 'P' port code is specified. 'S' Thru Hole, 'U' Dia. C' x 'Y' Deep Places from Other Side 'J ' Tapped Thru Places lank Toolplate Use Option Code T1 to specify a blank toolplate shown below. FF F C C Sensors for magnetic piston position indication must be ordered separately. See page 37. FF F C C Dimensional Data 3 0 Toolplate & ounting Inch Dimensions Specified by Port Code 'N' C F FF J 10-1/- 5/-18 7/-1 1/-13 1/-13 OT 1/- 1/- 5/-18 7/-1 1/-13 1/-13 T S U Y Toolplate & ounting etric Dimensions () Specified by Port Code '' or 'P' 3 0 C F FF J 5x 0.8 6x1.0 8x1.5 10x1.5 x1.75 x1.75 OT 6x1.0 6x1.0 8x1.5 10x1.5 x1.75 x1.75 T S U Y St'd Piston ag. Piston 0 St'd Piston ag. Piston St'd Piston ag. Piston St'd Piston ag. Piston St'd Piston ag. Piston St'd Piston ag. Piston (1.10) 38.0 (1.) 3.5 (1.36).5 (1.75) ' ' Dimension by & Stroke shown as (inches) (1.30) 3.0 (1.69) 39.5 (1.56) 9.5 (1.95) 0.5 (1.59).5 (1.99) 6.0 (1.81) 56.0 (.) 53.5 (.11).5 (.).0 (.8) 73.0 (.87) (1.) 8.0 (1.89).5 (1.75) 5.5 (.15) 5.5 (1.79) 55.5 (.19) 51.0 (.01) 61.0 (.0) 58.5 (.30) 68.5 (.70) 68.0 (.68) 78.0 (3.07) 3.0 (1.69) 53.0 (.09) 9.5 (1.95) 59.5 (.3).5 (1.99) 60.5 (.38) 56.0 (.) 66.0 (.60).5 (.) 73.5 (.89) 73.0 (.87) 83.0 (3.7) Stroke (1.89) 58.0 (.8) 5.5 (.15) 6.5 (.5) 55.5 (.19) 65.5 (.58) 61.0 (.0) 71.0 (.) 68.5 (.70) 78.5 (3.09) 78.0 (3.07) 88.0 (3.6) (.09).0 (.8) 59.5 (.3) 69.5 (.7) 60.5 (.38) 70.5 (.78) 66.0 (.60) 76.0 (.99) 73.5 (.89) 83.5 (3.9) 83.0 (3.7) 93.0 (3.66) (.8) 68.0 (.68) 6.5 (.5) 7.5 (.93) 65.5 (.58) 75.5 (.97) 71.0 (.) 81.0 (3.19) 78.5 (3.09) 88.5 (3.8) 88.0 (3.6) 98.0 (3.86) 0.0 (.8) 73.0 (.87) 69.5 (.7) 79.5 (3.13) 70.5 (.78).5 (3.17) 76.0 (.99) 86.0 (3.39) 83.5 (3.9) 93.5 (3.68) 93.0 (3.66) (.06) (.68) 78.0 (3.07) 7.5 (.93) 8.5 (3.33) 75.5 (.97) 85.5 (3.37) 81.0 (3.19) 91.0 (3.58) 88.5 (3.8) 98.5 (3.88) 98.0 (3.86) (.5) Page