Tiny Tim. Series T, VT, ET, and NFPA Air Actuators. Section 10

Transcription

1 Section 0 Tiny Tim Series T, VT, T, and NFP ir ctuators Series T & VT Features CT-0- Series T Features CT-0- Series T & VT Specifications CT-0- Series T Specifications CT-0-5 Series T, VT, and T Dimensions CT-0-6 T, VT, and T ccessories ct-0-9 Switches CT-0-0 T, VT, and T Ordering Information CT-0- Tiny Tim NFP Features CT-0- Series NFP Specifications CT-0- NFP Dimensions CT-0-5 NFP ccessories ct-0-8 NFP Ordering Information CT-0-0 Brookville, OH US Phone Fax CT-0-

2 Tiny Tim Series ctuators Series T & VT Tiny Tim ir Cylinders Series T Series T uses Quad ing Buna-ing piston seal Heads and Caps: Corrosion resistant Piston od: Hard chrome plated high alloy or black oxided steel. tensile steel piston rod. od Bushing: Oil-filled, sintered 5 Seals: O-ring type seals. iron bushing. od Seal: eplaceable block-vee Buna-N rod seal (Viton optional). 6 Tie ods: High yield strength tie rods. 7 Piston Seal: eplaceable quad ring Buna-N (Viton optional). 8 Piston: Machined alloy. 9 Tubing: Hard anodized I.D. aluminum tubing. Series VT Series VT uses Block-Vee Buna-N piston seal. This increases envelope dimension by /8" but provides lower breakaway pressure. (See CT-0- for specifications) Heads and Caps: Corrosion Piston od: Hard chrome plated high resistant alloy or black oxided steel. tensile steel piston rod. od Bushing: Oil-filled, sintered 5 Seals: O-ring type seals. iron bushing. 6 Tie ods: High yield strength tie od Seal: eplaceable block-vee rods. Buna-N rod seal (Viton optional). 7 Piston Seal: eplaceable Block- Vee Buna-N (Viton optional). 8 Piston: Machined alloy. 9 Tubing: Hard anodized I.D. aluminum tubing. CT-0- Brookville, OH US Phone Fax

3 Series T Tiny Tim ir Cylinders Series T Tiny Tim Series ctuators Series T actuators achieve their cushion effect through the normal compression of the Buna-N shock-absorber seals at the completion of the cylinder stroke. This compressive action absorbs the cylinder s kinetic energy and reduces the shock created by the piston striking the end caps. The measurable cushion effect of the shock-absorber seals provides a predictable pounds stoppable/piston speed ratio (Chart, CT-0-5), allowing you to determine the exact weight that can be stopped at a given piston speed. Series T actuators also help meet OSH s noise and clean air standards (Chart, CT-0-5). They are guaranteed to operate without lubrication for one year regardless of cycles. Non-lubricated operation is achieved by the combined efforts of an oil-impregnated sintered iron piston rod busing that lubricates the rod during normal operation, and through the use of a reinforced Teflon wear ring on the center perimeter of the piston. This ring reduces friction between the piston and the cylinder tube Heads and Caps: Corrosion resistant alloy or black oxided steel. Bushing: Oil-filled rod bushing. od Seal: eplaceable block-vee Buna-N rod seal (Viton optional). Seals: O-ring type seals. 5 Piston: Machined alloy. 6 Tie ods: High yield strength tie rods. 7 Wear ing: Teflon reinforced wear ring. 8 Tubing: Hard anodized I.D. aluminum tubing. 9 Impact Dampening Seals: Impact dampening seals specifically designed piston incorporated energy absorbing seals to dissipate the forces generated during impact without increasing envelope dimensions. Not available for cylinders with oversize rods. Not recommended for applications that require 00% repeatable stroke increments, or for applications that exceed the pounds stoppable capacities shown on CT-0-5 at the various recommended piston speeds. Brookville, OH US Phone Fax CT-0-

4 Series T & VT Tiny Tim /" and -/8" bore Single and double rod end styles ated 50 psi air -0 to 00 F (-9 to 07 C) operating temperatures Viton seals optional for higher temperatures Differences between Series T and Series VT air actuators Series T contains a Quad ing Buna-N piston seal. The VT Series utilizes a dual Block-Vee Buna-N piston seal design. The Block-Vee seals increase the envelope dimensions of the Series VT cylinders by /8". ll other features of the Series T and VT are the same. Series VT cylinders have a slightly lower breakaway pressure (psig) than the Series T Tiny Tim air cylinders. See Minimum Breakaway Pressures (PSIG) chart. Technical Information Medium: Compressed air, filtered, lubricated or non-lubricated Operation: Single or double acting Operating Pressure: 50 PSI (0 bar) Operating Temperature: -0 to 00 F (-9 to 07 C) Cylinder Diameters: /", -/8" Minimum Breakaway Pressures (PSIG) Non-cushioned cylinders, mounted horizontally with no load on the piston rod. Cylinder Bore (inches) Model PSIG Series T /" Series VT-T 8 Series T 7 -/8" Series VT-T 5 The proper selection and application of a fluid power actuator requires consideration of the following: Operation pressure, the fluid medium, mounting style, length of stroke, type of piston rod connection to the load, thrust or mounting tension loading on the rod, mounting attitude, speed of the stroke and how the load in motion will be stopped. Bore Size Selection The following formulae and charts may be used in the proper selection of the actuator bore size. xtended force in pounds = bore area in sq. inches x pressure to cap in psig. etract force in pounds = (bore area rod area) in sq. inches x pressure to head in psig. Bore reas Chart Bore reas Chart B Cylinder rea od Dia. rea Bore (in.) (Sq. in.) (in.) (Sq. in.) /". 5/6".076 -/8".99 /8. Note: llow for friction and attached mechanism when selecting cylinder bore size. lso, consider the weight of the piston and rod assembly if the cylinder is not mounted with the rod in a horizontal plane. CT-0- Brookville, OH US Phone Fax

5 Series T Tiny Tim /" and -/8" bore Single and double rod end styles ated 50 psi air -0 to 00 F (-9 to 07 C) operating temperatures Viton seals optional for higher temperatures Chart nergy bsorption of Impact Dampening Shock-bsorber Seals Inch-Pounds of *Pounds Stoppable at Following Speeds Cylinder Kinetic nergy Bore bsorbable in/sec in/sec 6 in/sec 8 in/sec 60 in/sec /" /8" * Pounds must include weight of piston and rod assembly. Chart ffect of Impact Dampening Seals on Total Stroke of Cylinder Cylinder eduction in inches of total stroke at following psi pressures Bore /" /8" NOT: The above figures are for new cylinders. The impact dampening seals will take some compression set during operation of the cylinder and the stroke loss will decrease. lso, the pressure at zero stroke loss will decrease to about 80 psi. t pressures above those of zero stroke loss, a slight clicking sound will be produced during impact. Chart Summary of Sound Levels in Decibles Cylinder Model TF /" x -/8" TF /" x -/8" With 95 psi ir Peak With 50 psi ir Peak Sound Pressure Level + Sound Pressure Level + nd+ + Side+ + nd+ + Side Peak sound pressure is given in decibels (db) re: x 0-5 N/m. ++ nd position of mike was located ft. on centerline from end of cylinder; side position of mike was located ft. perpendicular to centerline abeam of end of cylinder. The total noise emitted will depend on the structure to which the cylinder is attached. If it is mounted on a thin flat plate of considerable area, the noise will be increased by a sounding board effect. Brookville, OH US Phone Fax CT-0-5

6 (5) sq. Tiny Tim Series ctuators Standard Cylinder (TNM, VTNM, TNM) (9).6 (6) Series T, T, VT (/" Bore, 5/6" od) T + Stroke Flush Mount TF, VTF, TF.69 (8).56 () U + Stroke V + Stroke 5/6 8. () (9) /8 NPT. ().5 ().9 (5) Drilled & C'Bored for #6 Soc. Hd. Screw Front Flange Mount TF, VTF, TF ear Flange Mount TFC, VTFC, TFC Drilled & C'Bored for #0 Soc. Hd. Screw Z + Stroke Drilled & C'Bored for #0 Soc. Hd. Screw Y + Stroke (5).5 (8) (5).5 (8) (5). (8). (8) (5) Nose Mount TS, VTS, TS.8 () W + Stroke Clevis Mount TC, VTC, TC X + Stroke.8 (0). (8).8 (0) / 6. (). () / eam.6 (6) Head Trunnion Mount* THT, VTHT, THT Back Trunnion Mount* TBT, VTBT, TBT Dia /8" Max. adius /8" Max. adius Dia (9).5 (8) (9).8 (0) T + Stroke (9) S + Stroke (9).5 (8) (9) *Configured as special at factory Series T: Quad ing Seals Series VT: Block-Vee Seals Series T: cology Seals Series T Series T & VT. (). () S.8 (7).9 (8) T.8 (6).9 (56) U.9 (9). (59) V.8 (5) (5) W.6 (67) (76) X.56 (65).9 (75) Y.5 (6).88 (7) Z.8 (60) (70) NOT: For spring return cylinders add an additional stroke length to dimensions. CT-0-6 Brookville, OH US Phone Fax

7 Standard Cylinder (TNM, VTNM, TNM).8 (5) sq. Series T, T, VT (-/8" Bore, 5/6" and /8" ods) B T + Stroke Tiny Tim Series ctuators Flush Mount TF, VTF, TF.6 (6) U + Stroke V + Stroke (9) dia..88 () C. () (9) /8 NPT.5 () Drilled & C'Bored for #0 Soc. Hd. Screw Front Flange Mount TF, VTF, TF Drilled & C'Bored for #0 Socket Screw Z + Stroke ear Flange Mount TFC, VTFC, TFC Drilled & C'Bored for #0 Socket Screw Y + Stroke.8 (6).88 (8).8 (6).88 (8).8 (5). (8). (8).8 (5) Nose Mount TS, VTS, TS.8 () W + Stroke Clevis Mount TC, VTC, TC X + Stroke. ().8 (0). (8).5 () / 6. (). () / eam.8 () Head Trunnion Mount* THT, VTHT, THT Dia /8" Max. adius (9) Back Trunnion Mount * TBT, VTBT, TBT (9) /8" Max. adius Dia (0) S + Stroke (9).5 (8) (9. (9).5 (8) (9).8 (0) T + Stroke *Configured as special at factory Piston od 5/6 Diameter /8* Diameter 5/6-8 /8- B.6 (6) (9) C. (8) * /8" dia. piston rod will be furnished as an option only if specified. SeriesT Series T, VT. (). () S.8 (7).9 (8) T.8 (6).9 (56) U.9 (9). (59) V. ().69 () W.6 (67) (76) X.6 (67) (76) Y.5 (6).88 (7) Z.8 (60) (70) NOT: Series T, T & VT -/8" Bore Cylinders are available with adjustable cushions. Increase dimensions T through Z by 9/6" for one cushion and by -/8" for both ends cushioned. (See Ordering Procedure for details.) For spring return cylinders add an additional stroke length to above dimensions. Brookville, OH US Phone Fax CT-0-7

8 Tiny Tim Series ctuators Series DT, DT, VDT (Double od nd) Standard Cylinder (DTNM, VDTNM, DTNM) (5) (5) (9) dia. W + Stroke Stroke /8 NPT. (). (). () (9) (9). ().6 (6) Standard Cylinder (DTNM, VDTNM, DTNM).8 (5).8 (5) C (9) dia. W + Stroke Stroke B /8 NPT. () (9) (9). () Flush Mount DTF, VDTF, DTF Flush Mount DTF, VDTF, DTF Drilled & C'Bored for #6 Soc. Hd. Screw ( Holes).56 () X + Stroke.56 () + Stroke.6 (6) X + Stroke.6 (6) + Stroke.69 (8).88 ().9 (5).9 (5) Drilled & C'Bored for #0 Socket Screw ( Holes) Front Flange DTF, VDTF, DTF Drilled & C'Bored for #0 Soc. Hd. Screw Y + Stroke.8 (0) + Stroke Front Flange DTF, VDTF, DTF.8 (5).5 (6.) Y + Stroke.8 (0) + Stroke (5).5 (8).8 (6).88 (8). (8) Drilled & C'Bored for #0 Socket Screw. (8) Nose Mount DTS, VDTS, DTS Nose Mount DTS, VDTS, DTS.8 () W + Stroke.8 (0) + Stroke.8 () W + Stroke.8 (0) + Stroke /-6. ().56 () /-6. ().56 () Trunnion Mount * DTHT, VDTHT, DTHT /8" Max. adius Dia Ø -.00 *Configured as special at factory S + Stroke (9) Trunion Block Construction One piece Cast Ductile Iron. () + Stroke (9).5 (8) (9) Piston od 5/6 Diameter /8* Diameter 5/6-8 /8- B.6 (6) (9) C. (8) * /8" dia. piston rod will be furnished as an option only if specified. /" Bore -/8" Bore DT VDT & DT DT VDT & DT S.8 (7).9 (8).8 (7).9 (8) W.06 (5). (6).06 (5). (6) X.69 ().06 (5).56 (0).9 (9) Y.8 (60) (70).8 (60) (70) NOT: Series DT, VDT & DT -/8" bore cylinders are available with adjustable cushions. Increase dimensions S through Y by 9/6" for one cushion and by -/8 for both ends cushioned. CT-0-8 Brookville, OH US Phone Fax

9 Tiny Tim Series ctuators od Clevis (includes pin) (9) dia. eam. (8) Pin. ().68 (7).56 (0) Part Number Thread 005 5/ /8- (9).9 () Part Number 9085 (includes snap rings) (9) dia.. () od ye eam. (8).68 (7).56 (0) Mounting Screw.5 () 6- Th'd Part Number Thread 00 5/ /8- Part Number 50 Used on model TF, VTF, and TF /" bore actuators Clevis Bracket (includes pin) Mounting Nut 00 otation -/8" Bore Model C 50 otation /" Bore Model C #8 C-Bore.8 (9).88 (). (8). (8).7 (8) (9) dia..0 (6) sq..7 (5) sq..6 (). (8). () Part Number 500 Used on model TS, VTS, TS actuators Part Number 008 ngular Misalignment od ligners (includes jam nut).5 () F C B /6" Lateral Misalignment D od ligners PN Thread /-8 5/6-8 5/6- /8- (5) (5.) (5) (5) B.8 (5).8 (5).8 (5).8 (5) C. (5). (5). (5). (5) D.5 ().5 ().5 ().5 () (9) (9) (9) (9) F.6 ().9 (5).9 (5). (6) Brookville, OH US Phone Fax CT-0-9

10 Tiny Tim Series ctuators eed Switches PS0-B and PS0-B are compact and low profile switches when mounted on the cylinder tie rods. ach switch has a plug allowing electrical disconnection without removing or changing the adjustment of the switch on the cylinder. eed switches are constructed of two overlapping ferromagnetic reeds (nickel-iron) which are hermetically sealed in a glass tube with the ends aligned and a small gap between them. When an external magnetic force is applied, the reeds assume opposite polarity and the ends of the reeds are mutually attracted and contact, completing the circuit. Due to the light weight and small gap, very fast action is obtained. They will close in ms and release in 0. ms. Caution should be observed when using reed switches in sensitive circuits since they can introduce noise into the circuit due to bounce and vibration occurring from the mechanical closing of the reeds. eed switches require a magnetic material (located in the piston) with a polarity that is axial in orientation to actuate the switch. Note: Cylinders modified for use with a reed switch will have a magnetic strip on the piston in place of the Teflon wear strip. Technical Information Working Temperature Operating Time epeatability Vibration resistance Shock resistance Minimum magnetic field to actuate Maximum switch current Voltage range Maximum switch power Min. -0 F ( C) Max. 75 F ( C) On ms Off. ms.05 inch 50 to 000 Hz 50g 85 gauss (axial) see chart see chart 0W Note: piston modified for a reed switch will not work with a hall effect switch. eed Switch Quick eference Chart Switch Max. Max. Switch Voltage Part V Current ange Wire Number Type (Watt) esistance C-DC Light Hysteresis Varistor Plug-In Length PS0-B S.P./S.T. N.O. *50 * mp 5-50 Yes.0 Yes Yes " PS0-B S.P/S.T. N.O. *50 * mp 0-50 No.0 No Yes " *For inductive loads use 70% of the ratings. PS0-B Switch & Bracket For Tiny Tim Cylinders Part # PS0-B7T PS0-BT Fits /" Bore -/8" Bore How to Order TF- PS0-B 7T () / x 5 Switch Positions Switch and Bracket ssy. Quantity C PS0-B Switch & Bracket For Tiny Tim Cylinders Part # PS0-B7T PS0-BT BOWN D WHIT (BLCK) PS0-B, PS0-B (+) ( ) Fits /" Bore -/8" Bore How to Order TF-PS-/ x 5 Piston modification only (no switch) B Series Bore B C T (9).9 ().77 (5) VT.9 (9). (9).06 (7).56 (65) T NOT: PS Option add /" to overall length of cylinder. Min. Stroke Series Min. Stroke () Switches Same Side T (9) (5) VT & T.56 ().6 () CT-0-0 Brookville, OH US Phone Fax

11 Tiny Tim Series ctuators Hall ffect Switches Hall effect switches are a non-mechanical switch (no moving parts), which take the supply current and place it within a magnetic field, generating a voltage output. Hall effect switches are continually on, operating at a low voltage level (low ground), until the internal magnetic field is disturbed by the switch actuating magnetic. The built-in amplifier then boosts the output signal to a usable level. SInce there are no moving parts, hall effect switches can operate in sensitive areas without sending interference or noise into the circuit. Hall effect switches require a magnetic material (located on the piston) with a polarity that is longitudinal in orientation to actuate the switch. Note: piston modified for a hall effect switch will not work with a reed switch. Technical Information Working Temperature Operating Time epeatability Vibration resistance Shock resistance Minimum magnetic field to actuate Min. F ( C) Max. 57 F ( C) On ms Off. ms.00 inch 5 to 000 Hz ms 85 gauss (longitudinal) How to Order TF- HS-7T () / x 5 Switch Positions Switch and Bracket ssy. Quantity How to Order TF-HS-/ x 5 Piston modification only (no switch) Hall ffect Switch Quick eference Chart Switch Max. Max. Switch Voltage Part V Current ange Wire Number Type (Watt) esistance DC Light Diode Plug-In Length N.O. HS Sourcing 0 * mp 5- No Yes No 08" (PNP) N.O. HS Sourcing 0 * mp 5- Yes Yes No 08" (PNP) HS Sinking (NPN) *For inductive loads use 70% of the ratings. 0 * mp 5- No Yes No 08" HS Switch & Bracket HS Switch & Bracket HS Switch & Bracket Part # Fits Part # Fits Part # Fits HS-7T /" Bore HS-7T /" Bore HS-7T /" Bore HS-T -/8" Bore HS-T -/8" Bore HS-T -/8" Bore D LOD BLCK HS, HS-SOUCING (PNP) WHIT 5- VDC D LOD BLCK HS-SINKING (NPN) WHIT 5- VDC C B Series Bore B C T (9).9 ().8 (6) VT T. (9).06 (7).9 (56) NOT: PS Option add /" to overall length of cylinder. Min. Stroke Series Min. Stroke () Switches Same Side T (9).5 (6) VT & T.56 (). (6).78 (5) Brookville, OH US Phone Fax CT-0-

12 Tiny Tim Series ctuators V T, VT, and T Product Ordering Information T S /8 C N / x Single od nd Models T = Quad ring piston seal, block vee rod seal VT = Block-vee piston and rod seals T = Impact dampening piston seals and block-vee rod seal Double od nd Models DT = Quad ring piston, block vee rod seal VDT = Block-vee piston and rod seals DT = Impact dampening piston seals and block-vee rod seal Mounting Styles F = Flush mount C - CLevis mount S = Nose mount FC = ear flange mount F = Front flange mount HT = Head trunnion mount BT = Back trunnion mount od Diameter Specify 5/6" or /8" Single cting Cylinders (/" and -/8" bore cylinders) S = Spring on rod end (spring retracts rod). SC = Spring on cap end (spring extends rod). Notes: Cylinder requires a stop tube equivalent to the stroke length. Cushions not avilable on spring end of cylinder. Standard spring forces for S and SC =.5 lbs relaxed,.5 lbs compressed Cushions = od end cushion C = Cap end cushion C = Both ends cushioned Notes: vailable on -/8" bore cylinders only. /" effective cushion length. dd 9/6" to overall length of cylinder for each cushion. Cushion not available on spring end of a single acting cylinder. Options = T and VT stroke adjustment. (Specify length of adjustment) = T stroke adjustment (specify length of adjustment) Note: This option adds /" to overall cylinder length. N = lectroless nickel plating (includes option S). * V = Pneulectric valve (specigy position,,, or ) *L = Port location other than standard. (Specify location) P = Plain rod, no thread X = od extension over standard. (Specify length) S = Stainless steel tie rods and nuts. SS = Chrome-plated stainless steel piston rod. * SV = Stroke signal valve. (specify position,,, or ) TX = od thread extension over standard (specify length) V = Viton seals. -0 to 50 F temperature range. Bore (Specify /" or -/8") Stroke (inches) * Designate head position first, and cap position last Not available on /" and -/8" bore Series T CT-0- Brookville, OH US Phone Fax

13 NFP interchangeable Tiny Tim ir ctuators Series T, TV, T Heads and Caps: Corrosion resistant alloy od Bushing: Oil-filled, sintered iron bushing. od Seal: Carboxulated Nitrile Block-vee for maximum life and efficiency. Piston and od ssembly: Full diameter thread into the piston, secured with red Loctitie to resist shock and vibration. 5 Tie ods: Pre-stressed to maintain 8 Impact Dampening Seals: rigidity. Tie rod nuts are recessed into the head or caps for compactness and clean appearance. 6 Piston od: Hard chrome plated steel. Milled wrench flats and full diameter thread for maximum rod strength. 0 hard chrome plated stainless steel available at extra cost. 7 Tube: Hard anodized aluminum tube with micro-inch finish for low breakaway and long seal life. Impact dampening seals specifically designed piston incorporated energy absorbing seals to dissipate the forces generated during impact without increasing envelope dimensions. Not available for cylinders with oversize rods. Not recommended for applications that require 00% repeatable stroke increments, or for applications that exceed the pounds stoppable capacities shown on CT-0- at the various recommended piston speeds. Series T Series T features impact dampening piston design Series T Quad ing piston design Series TV Block-V piston design Brookville, OH US Phone Fax CT-0-

14 NFP Interchangeable Tiny Tim ctuators /", ", and -/8" bore Single and double rod end styles ated 50 psi air -0 to 00 F (-9 to 07 C) operating temperatures Viton seals optional for higher temperatures Designed to conform with NFP (T.6.) 97, and interchange with Tom Thumb s Series and V mounting dimensions. Minimum Breakaway Pressures (PSIG) Non-cushioned cylinders, mounted horizontally with no load on the piston rod. Cylinder Bore (inches) Model PSIG /" ", -/8" Series T Series T-TV Series T Series T-TV Temperatures Buna N Seals: -0 to 00 F (-9 to 07 C) Viton Seals: -0 to 50 F (-0 to 75 C) (DT-5) 8 (DT, DTV-) 7 (DT-) 5 (DT, DTV-9) Technical Information Medium: Compressed air, filtered, lubricated or non-lubricated Operation: Double acting Operating Pressure: 50 PSI (0 bar) Operating Temperature: -0 to 00 F (-9 to 07 C) Cylinder Diameters: Nominal Inch: /", -/8" ffective Piston reas To determine approximate force/lb multiply area by applicable pressure Bore Head nd* Cap nd /".9 sq. in.. sq. in. ".97 sq. in..99 sq. in. -/8".88 sq. in..99 sq. in. * With standard rods nergy bsorption Capacity of Impact Dampening Seals In./Lbs of Pounds* Stoppable at Following Speeds Kinetic nergy Size bsorbable in/sec in/sec in/sec in/sec in/sec in/sec /" " -/8" *Pounds must include piston and rod assembly weight CT-0- Brookville, OH US Phone Fax

15 Series T NFP Interchangeable Tiny Tim ctuators Bore / * -/8 BC.06 (7). (6).59 (0) CC /-8 5/6- /8- D. (6). (8) DB DN.6 (6).88 () (5) (5).8 (5).5 (8) W.8 (0).8 (0) KM 5/8-8 /-6 /-6 N (9) (5). (9) NT 8- x /6 DP 0- x / DP 0- x / DP.5 ().88 () (5) M.6 (6) (9) (9) M.69 (8).8 ().8 () T 8- x / DP 8- x / DP 0- x / DP SD. ().5 ().5 () SN. ().5 ().5 () TF.5 (8).88 (8) (5) TN.6 (6).88 () (5) UF (5).8 (60).5 (6) * Piston Dia. of " cylinders is -/8" diameter. Style (MS8) Side Through Holes /8 NPT Style (MS9) Side Tapped /8 NPT.5 () SN + Stroke (9) (5) + Stroke. (5) + Stroke.6 (6). () TN NT (Thread) ( in head, in cap) Style (MN) Threaded Male abbet* /8 NPT M (Dia.).5 () (9) (5) + Stroke.6 (67) + Stroke KM (Thread).5 (6). ().6 (6).6 (6) Style 5 (M) Head Male abbet *Configured as special at factory.5 () SD + Stroke (9) (5) + Stroke. (5) + Stroke Style (MP) Cap ye /8 NPT.6 (6). () DN DB (Three holes for Sockethead Capscrew).89 () Dia. / Dia M.00 (Dia.) T (Thread) ( Holes) /8 NPT.5 () (9) (5) + Stroke. (5) + Stroke.6 (6). () BC N.6 (6).5 (6). () (9).5 (). (8) (5) + Stroke. () W (9) Style 7 (MF) Cap ectangular Flange /8 NPT.8 (5) Dia ( Holes) /8 NPT.5 () (5) + Stroke.6 (67) + Stroke.88 (7) + Stroke Style 6 (MN) Threaded Nose KM (Thread) (9).6 (6).6 (6).5 () (5) + Stroke.8 (60) + Stroke (9). ().6 (6) Style 9 (MF7) Head Flange (No pilot) TF UF Style 8 (MF) Head Flange /8 NPT M (Dia.).8 (5) Dia ( Holes) /8 NPT.8 (5) Dia ( Holes).5 () (5) + Stroke. (5) + Stroke.6 (6) (9). () TF UF.5 () (5) + Stroke. (5) + Stroke. ().6 (6) (9) TF UF Brookville, OH US Phone Fax CT-0-5

16 Series T & TV NFP Interchangeable Tiny Tim ctuators Bore / * -/8 M.6 (6).6 (6).88 () BC.06 (7). (6).59 (0) CC /-8 5/6- /8- CD.8 (0).8 (0) D. (6). (8) DB DN.6 (6).88 () (5) (5).8 (5).5 (8) W.8 (0).8 (0) KM 5/8-8 /-6 - N (9) (5). (9) NT 8- x /6 DP 0- x / DP 0- x / DP.5 ().88 () (5) M.6 (6) (9) (9) M.69 (8).8 ().06 (7) T 8- x / DP 8- x / DP 0- x / DP SD.8 (6) (5) (5) SN.8 (6) (5) (5) TF.5 (8).88 (8) (5) TN.6 (6).88 () (5) UF (5).8 (60).5 (6) ZG. (79). (79).8 (86) * Piston Dia. of " cylinders is -/8" diameter. Style (MP) Cap ye.6 (6).5 (6) /8 NPT. () (9).5 ().5 (57) + Stroke.8 (86) + Stroke 57/6 Dia. CD. (8) Style 6 (MN) Threaded Nose /8 NPT.5 (6.) KM (Thread). () W (9) Style (MS9) Side Tapped /8 NPT.5 () SD + Stroke (9).5 (57) + Stroke.6 (67) + Stroke /8 NPT.5 () /8 NPT.5 () /8 NPT.5 () SN + Stroke M /8 NPT (9).5 (57) + Stroke ZG + Stroke M (9).5 (57) + Stroke.6 (67) + Stroke (9).5 (57) + Stroke.6 (67) + Stroke (6). () (Dia.). ().6 (6). ().6 (6). ().6 (6) (Dia.) KM (Thread).6 (6) M DN Style (MS8) Side Through Holes Style (MN) Threaded Male abbet* Style 5 (M) Head Male abbet BC DB (Three holes for Sockethead Capscrew) T (Thread) ( Holes) Style 7 (MF) Cap ectangular Flange N.8 (5) Dia ( Holes) TN NT (Thread) ( in head, in cap) *Configured as special at factory.5 ().5 (57) + Stroke ZG + Stroke (9) M Style 8 (MF) Head Flange /8 NPT.6 (6).8 (5) Dia ( Holes).5 ().5 (57) + Stroke.88 (7) + Stroke /8 NPT (9). ().6 (6) Style 9 (MF7) Head Flange (No pilot) TF UF.8 (5) Dia ( Holes).5 ().5 (57) + Stroke.88 (7) + Stroke.6 (6) (9). () TF UF.5 ().5 (57) + Stroke.88 (7) + Stroke. ().6 (6) (9) TF UF CT-0-6 Brookville, OH US Phone Fax

17 Bore / * -/8 Series DT DT-DTV DT DT-DTV DT DT-DTV.8 (5) (5).88 (8) M.6 (6).6 (6).6 (6) B (5). (5).5 (57) BC.06 (7). (6).59 (0) CC /-8 5/6- /8- D. (6). (8) DB DN.6 (6).88 () (5) (5).8 (5).5 (8) KM 5/8-8 /-6 /-6 - LB (5).5 (6) (5).5 (6) (5).5 (6) N (9) (5). (9) NT 8- x /6 DP 0- x / DP 0- x / DP.5 ().88 () (5) M.6 (6) (9) (9) M.69 (8).8 ().8 ().06 (7) T 8- x / DP 8- x / DP 0- x / DP SD.06 (5).56 (65) (5).5 (6) (5).5 (6) SN.56 (0).06 (5).5 (8) (5).5 (8) (5) TF.5 (8).88 (8) (5) TN.6 (6).88 () (5) UF (5).8 (60).5 (6) ZB (70).5 (8) (70).5 (8) (70).5 (8) Z.5 (8) (95).5 (8) (95).5 (8) (95) ZT (76).5 (89) (76).5 (89) (76).5 (89) * Piston Dia. of " cylinders is -/8" diameter. Tiny Tim Series NFP Interchangeable ctuators Style (MS9) Side Tapped.6 (6). ().6 (6).5 () (9) /8 NPT ( Holes) /8 NPT SD + Stroke LB + Stroke ZB + X Stroke /8 NPT (9) ( Hole).6 (6) NT (thread) (9) (9). () SN + Stroke LB + Stroke ZB + X Stroke Style (MS8) Side Through Holes.8 (0).6 (6). () Style (MN) Threaded Male abbet* KM (Thread) DB (Four holes for Sockethead Capscrew) DN B TN Style 5 (M) Head Male abbet /8 NPT T (Thread) ( Holes) N.6 (6). () (9) LB + Stroke Z + X Stroke (9). () M.6 (6) *Configured as special at factory.6 (6). () (9) LB + Stroke ZB + X Stroke (9).6 (6). (.) BC Style 6 (MN) Threaded Nose KM (Thread) /8 NPT Style 8 (MF) Head Flange /8 NPT UF TF.6 (6). () (9) LB + Stroke Z + X Stroke (9) M.6 (6).5 (6.).6 (6). () (9) LB + Stroke ZT + X Stroke (9).5 (6.).6 (6). ().8 (5) Dia. ( Holes) Style 9 (MF7) Head Flange (No pilot) /8 NPT UF TF.6 (6). () (9) LB + Stroke ZB + X Stroke (9). ().6 (6).8 (5) Dia. ( Holes) Brookville, OH US Phone Fax CT-0-7

18 Tiny Tim Series NFP Interchangeable ctuators Pivot Pin CD CL CP Cyl. Cyl. Part Bore Series No. CD CL CP / ll 9085 (9).9 (), -/8 T ().06 (7), -/8 TV-T (0).88 ().06 (7) ye Bracket.5 (). (8) CB.5 () CD (dia.) DB (Four Holes For Sockethead Capscrew) Cyl. Cyl. Part Bore Series No. CD CB DB / T, TV-T (5) (9) & T (0) 0-.8 (5) (5) -/8 TV-T (0).8 (0) 0-.8 (5) (5) Clevis Bracket (includes pin).5 () FL.5 () CB CB CD (dia.) DB (Four Holes For Sockethead Capscrew) Cyl. Cyl. Part Bore Series No. FL CB CD DB / T, TV-T 907 (5) (9).9 (0) 6- & T (5) (5).5 ().8 (0) 0- -/8 TV-T (5) (5).5 ().8 (0).8 (0) 0- od ye CB CD (dia.). () (Full Thread) (5) dia. CB. () J Cyl. Cyl. Part Bore Series No. CC CD CB I J / T, TV-T 9075 /-8.5 (). (8) T /6-.8 (0) (9). () TV-T /6-.8 (0).8 (0) (9). () -/8 T 9078 /8-.8 (0) (9). () TV-T 9079 /8-.8 (0).8 (0) (9). () od Clevis (includes pin) G (dia.) CB CD (dia.). () F (dia.) CB.5 () K Cyl. Cyl. Part Bore Series No. CB CD F G K CC / T, TV-T () (9).9 (5) /-8 T (0).56 ().88 () 5/6- TV-T (0).8 (0).56 ().88 () 5/6- -/8 T (0).56 ().88 () /8- TV-T (0).8 (0).56 ().88 () /8- CT-0-8 Brookville, OH US Phone Fax

19 Tiny Tim Series NFP Interchangeable ctuators od ligners (includes jam nut) ngular Misalignment.5 () F /6" Lateral Misalignment Model B C D F CC CC (Th'd) C B D CC (Th'd) -5 (5).8 (5). (5).5 () (9).6 () /-8 - (5).8 (5). (5).5 () (9).9 (5) 5/6- -8 (5).8 (5). (5).5 () (9).9 (5) / (8).78 (5) (76).69 (8). (). (6) 7/ (8).78 (5) (76).69 (8). () /-0 Oversize ods Optional od nd Styles CC MM M Note: Oversize rods are not available in Style, sizes /" and " due to interference with the rod gland. See CT-0-0 for cylinders equipped with modified rods or other optional equipment. KK MM M od CC KK Bore Size MM (Style ) (Style B) D M /" /-8.6 (6) 0-. (6).6 (6). (8) 5/6-.6 (6) /-8.6 (6). (8) 5/6-.6 (6) /-8 (9) ".8 (0) /8-.6 (6) 5/6-. (8) (9)*.5 () /-0 (9) 7/6-0. () (9)* -/8".8 (0) /8-.6 (6) 5/6-. (8) (9)*.5 () /-0 (9) 7/6-0. () (9)* Optional rod sizes indicated on shaded areas. Not available on Series T and DT. * on Series TV and DTV " & -/8" Sizes in Mounting Styles 5 and 8 is ". Optional quipment High temperature seals vailable for all seals and bore sizes when normal service requires the cylinder to operate at ambient temperatures ranging above 00 to 50 F ( 9 to 77 C). Specify Viton. Single cting, Spring eturn ctuators vailable for all Series and bore sizes. dd two times working stroke to envelope dimensions shown on CT-0-6/7 djustable Cushions Insert type adjustable cushions are available when required. dd /" to cylinder length per cushioned end. Note: Not available with /" diameter rods. Brookville, OH US Phone Fax CT-0-9

20 Tiny Tim Series NFP Interchangeable ctuators NFP Product Ordering Information T 6 /8 D N / x Series Standard Single od nd Models T = Quad ring piston seal, Block-V rod seal TV - Block-V piston and rod seals T = Impact dampening piston seals, Block-V rod seal Standard Double od nd Models DT = Quad ring piston seal, Block-V rod seals DTV - Block-V piston and rod seals DT = Impact dampening piston seals, Block-V rod seal Mounting Styles = Side Tapped = Side through holes = Cap eye 5 = Head male rabbet 6 = Threaded nose 7 = Cap rectangular flange 8 = Head flange 9 = Head flange (no pilot) od Diameter (Specify on all models) /" 5/6" /8" /" Note: /" diameter rods are not available on Series T od nd Thread Style (Specify or B on all models) od Size Thd Thd B / ø /-8 0-5/6 ø 5/6- /-8 /8 ø /8-5/6- / ø /-0 7/6-0 Bore /" " -/8" Stroke Options X = od extension (specify length) TX = od thread extension (specify length) T = Special od thread (specify length) P = Plain rod end PS = Magnetic piston** L = Port location other than standard (specify location) ST = Stop tube. (specify length and location) = Stroke adjust (specify length ofadjustment) = Stroke adjustment (double piston design) V = Viton seals SS = Piston od (chrome plated stainless steel) N = lectroless nickel plating (includes option S) S = Stainless steel tie rods &nuts Single cting ctuators S = Spring on od nd SC = Spring on Cap nd ** PS option adds /" to overall length. djustable Cushions* D = od end only DC = Cap end only D = Both ends * dd /" per cushioned end. CT-0-0 Brookville, OH US Phone Fax