Models: Description: F210Z Series w/ 61" icd Mower Deck (F210ZKAV2661) F210Z Series w/ 61" icd Mower Deck (F210ZBVE2861)

Transcription

1 Parts Manual F210Z Series Zero-Turn Riding Mower Models: Description: F210Z Series w/ 61" icd Mower Deck (F210ZKAV2661) F210Z Series w/ 61" icd Mower Deck (F210ZBVE2861) F210Z Series w/ 61" icd Mower Deck (F210ZKAV2661 CAL) F210Z Series w/ 61" icd Mower Deck (F210ZBVE2861 CAL) F210Z Series w/ 61" icd Mower Deck (F210ZBVE2861 ANSI-EXP) Briggs and Stratton Power Products Group, LLC North Main Street Munnsville, NY USA Revision C Rev. Date: 02/06/17

2

3 Table Of Contents MODEL COMPONENTS PAGE Main Frame & Front Casters Group... 4 Rear Bumper & ROPS Group... 6 Seat & Kick Plate Group S/N: & Above... 8 Seat & Kick Plate Group S/N: & Below Fuel Supply Hose, Tank Replacement Parts, and EVAP Group Fuel Tank & Mount Group Instrument Control Panel Group Engine & PTO Group - Kawasaki Engine & PTO Group - Briggs & Stratton EFI Transaxle Drive Group - S/N: & Below Transaxle Drive Group - S/N: & Above Motion Control Group Hydraulic Group Parking Brake Group Deck Lift Group Transaxle SERVICE PARTS - ZT Wheel & Tire Group Decal Group - Safety & Operation USA Models Decal Group - Brand & Model Decal Group - Safety & Operation Export Models Evap Canister Group - CAL Models " Mower Deck - Housing, Covers, Spindles & Blades " Mower Deck Group - Rollers & Casters " Mower Deck - Hanger Chains " Mower Deck - Pulleys, Belt & Idler Arm Spindle Service Parts Electrical Group - Kawasaki S/N: & Below Electrical Group - Briggs & Stratton EFI S/N: & Below Electrical Group - Briggs & Stratton EFI S/N: & Above Electrical Group - Kawasaki S/N: & Above Electrical Schematics - Kawasaki S/N: & Below Electrical Schematics - B&S EFI S/N: & Below Electrical Schematics - Kawasaki S/N: & Above Electrical Schematics - B&S EFI S/N: & Above Torque Specification Chart... Inside Back Cover

4 Main Frame & Front Casters Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 4

5 Main Frame & Front Casters Group REF NO PART NO. QTY. DESCRIPTION BEARING, TAPERED ROLLER SEAL, GREASE WASHER, 3/4 SAE NUT, 3/4-16, HEX JAM NYLON LOCK WASHER, BELLEVILLE X CAP, LOW PROFILE, STEEL B 2 WELD, CASTER YOKE - RED 8-1 * WELD, FRAME, F210Z - RED * If frame is damaged, call ext BOLT, 1/4-28 X 1/2, GD5 YZ GROMMET, 2" ID CUP, BEARING (SV) GROMMET, 7/8"ID, 1/4" THICK STK Footnotes 5

6 Rear Bumper & ROPS Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 6

7 Rear Bumper & ROPS Group REF NO PART NO. QTY. DESCRIPTION PLUG, PANEL, BLACK B 1 WELD, BUMPER - F210Z - RED B 1 PLATE, CARB PROTECTOR, F210Z - RED A 1 PLATE, HEAT SHIELD - BLK ROPS (Call x708 if replacing a ROPS) A 1 EXTENSION, SEAT BELT - BLK SEAT BELT ASSM, RETRACTOR + SUP SLEEVE ORDER P/N (CONTAINS BOTH SEAT BELT RETRACTOR & SUPER SLEEVE BUCKLE) SCREW, 1/2-13 X 1.00, SHCS WASHER, 5/16 SAE X6 6 BOLT, 5/16-18 X 3/4 GD5 CZ NUT, 5/16-18 HEX NYLOCK FLANGE X12 4 BOLT, 1/2-13 X 1-1/2 GD5 CZ NUT, 1/2-13 HEX NYLON LOCK X10 1 BOLT, 1/2-13 X 1-1/4 GD5 CZ WASHER, 1/2 SAE NUT, 1/2-13 HEX NYLOCK FLANGE X26 4 BOLT, 1/2-13 X 3-1/4 GD5 CZ (SV) NUT, 1/2-13 HEX SIDE LOCK (SV) PIN, HITCH,.50 X 3.25 W/ LAY (SV) X1 1 HARDWARE KIT, ROLL BAR (SV) Footnotes 7

8 Seat & Kick Plate Group S/N: & Above NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 8

9 Seat & Kick Plate Group S/N: & Above REF NO PART NO. QTY. DESCRIPTION A 1 WELD, SEAT SWITCH, IS700 - BLK B 1 PLATE, RIGID FLOOR, 200XT - RED B 1 PLATE, REMOVABLE FLOOR, 200XT - RED ASSM, SEAT PLATE W/ DECAL, F320Z-DOM ( B) X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE BOLT-RD HD SH SQ NK 5/16-18X1.500 G5 YZ MNT, VBRTN, RBBR NUT, 5/16-18, HEX, CNTR LK,ZINC PHOS/OIL X6 2 SCREW, #10-24 X 3/4 ROUND PHILLIPS KNOB-INT THR ARM 2.12WD 1.06LG NUT, 5/16-18 HEX NYLOCK FLANGE SPACER,.38 X.50 X 5.06, CZ WASHER, 3/8 SAE X48 1 BOLT, 3/8-16 X 6 GD5 CZ WASHER,.39 X 2.00 X X NUT, 3/8-16 HEX NYLOCK FLANGE SPRING,.688 ID X.130 WIRE DIA WASHER, 5/16 SAE X24 2 BOLT, 3/8-16 X 3 GD5 CZ SAFETY WALK, X X8 5 BOLT, 5/16-18 X 1 GD5 CZ SWITCH, PLUNGER, N.C SEAT, MID BACK, W/SUSPENSION, SEATS INC X1 1 4" SINGLE LOCKING TRACKS BASE (SV) X1 1 ARM PAD ASSEMBLY BLK/CHAR CAR FIB/HARBR GRY RED WELT (SV) X2 1 SET OF ARMREST ASSEMBLY BLK/CHAR CAR FIB/HARBR GRY RED WELT (SV) X2 1 WEIGHT ADJUST INDICATOR KNOB ASSY BASE (SV) X3 1 BELLOWS W/ HARDWARE BASE (SV) X4 1 BACK COVER FOR FIXED BACK I3M BLK/CHAR CAR FIB/HARBR GRY RED WELT (SV) X5 1 CUSHION COVER FOR I3M BLK/CHAR CAR FIB/HARBR GRY RED WELT (SV) NUT, #10-24 HEX NYLON LOCK (SV) WASHER, 3/8 USS Footnotes 9

10 Seat & Kick Plate Group S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 10

11 Seat & Kick Plate Group S/N: & Below REF NO PART NO. QTY. DESCRIPTION NUT, 5/16-18 HEX NYLOCK FLANGE SPACER,.33 X.66 X 1.31 SHLDR, CZ SPRING, COMP 720ID X 1.310LG X.118WIRE SAFETY WALK, X B 1 PLATE, SEAT SWITCH - RED ASSM, SEAT PLATE W/DECALS,200XT-FRS ( B) B 1 PLATE, REMOVABLE FLOOR, 200XT - RED B 1 PLATE, RIGID FLOOR, 200XT - RED SPRING, SEAT SUPPORT WASHER,.34 X 1.25 X 10 GA SWITCH, PLUNGER, NO, SINGLE POLE SNAP-IN NUT, 5/16-18, HEX, CNTR LK,ZINC PHOS/OIL KNOB-INT THR ARM 2.12WD 1.06LG MNT, VBRTN, RBBR X10 1 BOLT, 5/16-18 X 1-1/4, CARRIAGE CZ WASHER, 3/8 SAE X28 2 BOLT, 3/8-16 X 3-1/2 GD5 CZ NUT, 3/8-16 HEX NYLOCK FLANGE X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE WASHER, 5/16 SAE X8 2 BOLT, 5/16-18 X 1 GD5 CZ X18 2 BOLT, 5/16-18 X 2-1/4 GD5 YZ SEAT, MID BACK, W/SUSPENSION, SEATS INC X1 1 4" SINGLE LOCKING TRACKS BASE (SV) X1 1 ARM PAD ASSEMBLY BLK/CHAR CAR FIB/HARBR GRY RED WELT (SV) X2 1 SET OF ARMREST ASSEMBLY BLK/CHAR CAR FIB/HARBR GRY RED WELT (SV) X2 1 WEIGHT ADJUST INDICATOR KNOB ASSY BASE (SV) X3 1 BELLOWS W/ HARDWARE BASE (SV) X4 1 BACK COVER FOR FIXED BACK I3M BLK/CHAR CAR FIB/HARBR GRY RED WELT (SV) X5 1 CUSHION COVER FOR I3M BLK/CHAR CAR FIB/HARBR GRY RED WELT (SV) Footnotes 11

12 Fuel Supply Hose, Tank Replacement Parts, and EVAP Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 12

13 Fuel Supply Hose, Tank Replacement Parts, and EVAP Group REF NO PART NO. QTY. DESCRIPTION CLAMP, HOSE, EXTERNAL, 1/2 - RED X15P5 1 HOSE, 1/4" FUEL, 15.50" (B&S EFI Engines - S/N: & Below) X52 1 HOSE, 1/4" FUEL, 52.00" X34 1 HOSE, 1/4" FUEL, 34.00" (B&S EFI Engines) X25 1 HOSE, 1/4" FUEL, 25.00" (Kawasaki Engine) X22 1 HOSE, 1/4" FUEL, 22.00" (Kawasaki Engines - S/N: & Below) VALVE, FUEL SHUT-OFF, X39 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Engines) X21P5 1 HOSE, VAPOR, 5MM ID, LG (B&S EFI Engines) X32 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Engines) X2 1 HOSE, VAPOR, 5MM ID, 2.00 LG (Qty: 2 - Kawasaki Engines) X9 1 HOSE, VAPOR, 5MM ID, 9.00 LG (B&S EFI Engines) X16 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Engines) X15 1 HOSE, VAPOR, 5MM ID, LG (B&S EFI Engines) X25 1 HOSE, VAPOR, 5MM ID, LG (B&S EFI Engines) HOSE ASSEMBLY (SV) TIE,SELF-LOCKING, 6" (Qty: 5 - B&S EFI Engines) REMOTE, VENT ASSEMBLY, NO VALVE (SV) GROMMET (SV) X3 1 FUEL FILTER (SV) FILTER, FUEL BUSHING-FUEL TANK RED RUBBER (SV) FITTING, 3/16" TEE, BARB TYPE, HDPE X25 1 HOSE, 1/4" FUEL, 25.00" (B&S EFI & Kawasaki Engines - S/N: & Above) Footnotes 13

14 Fuel Tank & Mount Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 14

15 Fuel Tank & Mount Group REF NO PART NO. QTY. DESCRIPTION A 1 PLATE,MOTION CONTROL GUARD F320/210Z LH, BLK (S/N: & Above) A 1 PLATE,MOTION CONTROL GUARD F320/210Z RH, BLK (S/N: & Above) A 1 WELD, FUEL MOUNT, RH, F210Z - BLK (S/N: & Above) A 1 WELD, FUEL MOUNT, LH, F210Z - BLK (S/N: & Above) A 1 GUARD, SEAT, LH, F210Z - BLK (S/N: & Above) A 1 GUARD, SEAT, RH, F210Z - BLK (S/N: & Above) B 2 BADGE, IS IS RED TANK, FUEL, 5.75 GAL,MED, Z-LH, LOW PERM TANK, FUEL, 5.25 GAL,MED, Z-RH, LOW PERM FUEL CAP, 3-1/2", MANAGED VENT OUT, 12" WASHER, 5/16 F436 FLAT WASHER, 5/16 LOCK CZ X6 8 BOLT, 5/16-18 X 3/4 GD5 CZ WASHER, 5/16 SAE X8 6 BOLT, 5/16-18 X 1 GD5 CZ NUT, 5/16-18 HEX NYLOCK FLANGE X6 8 BOLT, 1/4-20 X 3/4 GD5 CZ NUT, 1/4-20 HEX NYLOCK FLANGE WASHER, 1/4 SAE SCREW, #10-24 X 3/8 ALLEN BHBZ GAUGE, FUEL, 12 (SV) X1 2 GROMMET, FUEL GAUGE (SV) A 1 PLATE,MOTION CONTROL GUARD F210Z LH, BLK (S/N: & Below) A 1 PLATE,MOTION CONTROL GUARD F210Z RH, BLK (S/N: & Below) A 1 WELD, FUEL MOUNT, RH, F210Z - BLK (S/N: & Below) A 1 WELD, FUEL MOUNT, LH, F210Z - BLK (S/N: & Below) A 1 GUARD, SEAT, LH - BLK (S/N: & Below) A 1 GUARD, SEAT, RH - BLK (S/N: & Below) Footnotes 15

16 Instrument Control Panel Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 16

17 Instrument Control Panel Group REF NO PART NO. QTY. DESCRIPTION FUSE, ATO, 20 AMP COVER, VINYL FUSEBLOCK FUSE BLOCK X4 3 SCREW,ALLEN HEAD 1/4-20X.500 ZINC PHOS PLUG,.820X1.44 HOLE, BLACK PLASTIC SWITCH, BLADE ENGAGEMENT SWITCH, IGNITION, 6 POST * HOUR METER, ASSEMBLY ( ) * When replacing this hour meter, please call our service department at ext CABLE, CHOKE CONTROL, 47 (Kawasaki Engines Only) LIGHT, INDICATOR, PANEL, RED (Briggs & Stratton EFI Engines Only) X6 2 SCREW, #10-24 X 3/4 ROUND PHILLIPS A 1 PANEL, CONTROL, IS2100Z - BLK (Kawasaki Engines Only) RING, SWITCH RETAINER CABLE, THROTTLE, 42" A 1 PANEL, CONTROL, IS2100Z - BLK (Briggs & Stratton EFI Engines Only) LEVER, THROTTLE CONTROL, HEAVY-DUTY O-RING, 7/8 ID X 1/16 W NUT, #10-24 HEX NYLON LOCK NUT, 3/8-24 HEX (Kawasaki Engines Only) X1 1 KNOB, THROTTLE CONTROL (SV) KEY, IGNITION MOLDED SET (SV) COVER, PLASTIC, SNAP ON (SV) NUT, PLASTIC (SV) FUSE, ATO, 15 AMP Footnotes 17

18 Engine & PTO Group - Kawasaki NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 18

19 Engine & PTO Group - Kawasaki REF NO PART NO. QTY. DESCRIPTION CLUTCH, WARNER, 200 ft lbs " MUFFLER, KAWASAKI, 5" CAN (Replacement Muffler does not require components to secure muffler to engine deck) NUT, 5/16-18 HEX NYLOCK FLANGE CLUTCH ANCHOR PAD WASHER,.34 X 1.25 X 10 GA WASHER, 5/16 SAE X8 4 BOLT, 5/16-18 X 1 GD5 CZ X14 2 BOLT, 5/16-18 X 1-3/4 GD5 CZ BOLT, CRANKSHAFT,7/16-20X2-3/4, GD8 (Torque crankshaft bolt to 65 ft. lbs. (88 Nm)) 10 FX801V-ES00-S 1 ENGINE, 26HP KAWA, FX801V NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) X18 1 BOLT, 5/16-18 X 2-1/4 GD5 TFL, ZN GROMMET, 7/8"ID, 1/4" THICK STK A 1 ANCHOR, CLUTCH - BLK SPACER,.39 X 1.00 X.80, CZ X10 1 KEY, 1/4 SQ X 1-1/ BOLT, 3/8-16 X 1-1/4, SF, PLT W/PATCH SPACER, 1.13 X 1.75 X 1.03, CZ SPACER, 1.13 X 1.75 X HOSE, OIL DRAIN, M20 X PULLEY, 4.75 OD X 1-1/8 BORE, BC EXTENSION, TAILPIPE, 3" SCREW,SELF-TAP,#8-32 X 3/8,WASH HEX, CZ BELLEVILLE WASHER X.442 X SET SCREW, 5/16-18 X 3/8, KNURL, W/PATCH (SV) BOLT, M X 20 MM GD NUT, M SERR. FLANGE, CZ Footnotes 19

20 Engine & PTO Group - Briggs & Stratton EFI NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 20

21 Engine & PTO Group - Briggs & Stratton EFI REF NO PART NO. QTY. DESCRIPTION CLUTCH, WARNER, 200 ft lbs " SCREW,SELF-TAP,#8-32 X 3/8,WASH HEX, CZ NUT, 5/16-18 HEX NYLOCK FLANGE CLUTCH ANCHOR PAD WASHER,.34 X 1.25 X 10 GA WASHER, 5/16 SAE X8 4 BOLT, 5/16-18 X 1 GD5 CZ WASHER, 5/16 INT. TOOTH LOCK BOLT, CRANKSHAFT,7/16-20X2-3/4, GD8 (Torque crankshaft bolt to 65 ft. lbs. (88 Nm)) 10 49E G1 1 ENGINE, 28HP BRIGGS VANGUARD, EFI NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) X18 1 BOLT, 5/16-18 X 2-1/4 GD5 TFL, ZN GROMMET, 7/8"ID, 1/4" THICK STK NUT, 5/16-24, TOP LOCK FLANGE, GD8 PHOS A 1 ANCHOR, CLUTCH - BLK X10 1 KEY, 1/4 SQ X 1-1/ X12 1 BOLT-HEX, 5/16-24 X 1-1/2", GD8, PHOS SPACER, 1.13 X 1.75 X 1.35, CZ PULLEY, 4.75 OD X 1-1/8 BORE, BC EXTENSION, TAILPIPE, 3", BLACK X14 3 BOLT, 5/16-24 X 1-3/4, GD8, PHOS HOSE, OIL DRAIN BELLEVILLE WASHER X.442 X NUT, 5/16-24 JAM SET SCREW, 5/16-18 X 3/8, KNURL W/ PATCH (SV) Footnotes 21

22 Transaxle Drive Group - S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 22

23 Transaxle Drive Group - S/N: & Below REF NO PART NO. QTY. DESCRIPTION NUT, 3/8-16 HEX SERRATED FLANGE NUT, 1/2-13 HEX NYLOCK FLANGE SPRING-EXT, 1.04 ODX6.935LGX.148WR, BLK EYE BOLT, 3/8-16 X 5, 2.88THRD, 1EYE, CZ X36 1 BOLT, 1/2-13 X 4-1/2 GD5 CZ NUT, 3/8-16 HEX NYLOCK FLANGE ASSM, IDLER ARM, PUMP DRIVE, 1/2ID, CAST (SV) (Includes items #9, 10, & 15) PULLEY-IDLER, 5.00OD,.385ID,.75W, STL SPACER, IDLER ARM, 1/2, PM SPACER,.52 X.84 X 1.53, PM X12 1 BOLT, 3/8-16 X 1-1/2 GD5 CZ BELT, HB SEC, 81.2EL A 1 PLATE, IDLER ARM ADAPTER - BLK X20 1 BOLT, 3/8-16 X 2-1/2 GD5 CZ BEARING, BALL, AXLE SPACER,.52 X 1.75 X.63, CZ X16 1 BOLT, 3/8-16 X 2 GD5 CZ Footnotes 23

24 Transaxle Drive Group - S/N: & Above NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 24

25 Transaxle Drive Group - S/N: & Above REF NO PART NO. QTY. DESCRIPTION NUT, 3/8-16 HEX SERRATED FLANGE NUT, 1/2-13 HEX NYLOCK FLANGE SPRING-EXT, 1.04 ODX6.935LGX.148WR, BLK EYE BOLT, 3/8-16 X 5, 2.88THRD, 1EYE, CZ X36 1 BOLT, 1/2-13 X 4-1/2 GD5 CZ NUT, 3/8-16 HEX NYLOCK FLANGE ASSM, IDLER ARM, PUMP DRIVE, 1/2ID, CAST (SV) (Includes items #9, 10, & 15) PULLEY-IDLER, 5.00OD,.385ID,.75W, STL SPACER, IDLER ARM, 1/2, PM SPACER,.52 X.84 X 1.53, PM X12 1 BOLT, 3/8-16 X 1-1/2 GD5 CZ BELT, HB SEC, 81.2EL A 1 PLATE, IDLER ARM ADAPTER - BLK X20 1 BOLT, 3/8-16 X 2-1/2 GD5 CZ BEARING, BALL, AXLE SPACER,.52 X 1.75 X.63, CZ X14 1 BOLT, 3/8-16 X 1-3/4 GD5 CZ SPACER,.39 X 1.00 X.25, PM, CZ (S/N: & Below) WASHER-3/8 FENDER (S/N: & Below) WASHER, 3/8 USS (S/N: & Above) Footnotes 25

26 Motion Control Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 26

27 Motion Control Group REF NO PART NO. QTY. DESCRIPTION BEARING, BRONZE FLANGE, 3/ BALL JOINT 5/16-24 RH FEMALE BRONZE RACE SWITCH, PLUNGER, N.O BEARING, FLANGE GRIP, FOAM, 3/4 ID, 16 LONG (S/N: & Below) BALL JOINT 5/16-24 LH FEMALE BRONZE RACE NUT, 5/16-18 HEX NYLOCK FLANGE A 2 MOUNT, CONTROL ARM - BLK (10.95" Total Length, 3 Adjustment Holes) DAMPENER, CONTROL,#(P6709/P3610) BALL STUD, 5/16 X.50,# PC-477-2) A 1 WELD, HANDLE MOTION CONTROL LH - BLK (S/N: & Below) A 1 WELD, HANDLE MOTION CONTROL RH - BLK (Not Illustrated)(S/N: & Below) X8 6 BOLT, 3/8-16 X 1 GD5 YZ X10 4 BOLT, 5/16-18 X 1-1/4 GD5 YZ NUT, 3/8-16 HEX NYLON LOCK NUT, 5/16-18 HEX SERRATED FLANGE (SMALL) X14 4 BOLT- 5/16-18 X 1-3/4 GD5 TFL X14 4 BOLT, 3/8-16 X 1-3/4 GD X4 4 SCREW- #10-24 X 1/2 ROUND PHILLIPS NUT, #10-24 HEX A 1 WELD, CONTROL SHAFT, RH - S200XT - BLK (Not Illustrated) A 1 WELD, CONTROL SHAFT, LH - S200XT- BLK A 2 PLATE, HYDRO CONNECTOR, S200XT - BLK ROD, HYDRO LINKAGE - S200XT - YZ SPACER,.38 X.75 X 1.25, PM, CZ X20 2 BOLT, 5/16-18 X 2-1/2 GD5 YZ WASHER, 5/16 SAE SCREW, 5/16-18x0.750, GR5, WHIZ-LOCK, ZC NUT, 5/16-24 HEX BOLT, 3/8-16 X 1-1/4 SHCS NUT, 5/16-24 HEX, LH X6 2 BOLT, 7/16-14 X 3/ NUT, 7/16-14 HEX NYLON LOCK GRIP, FOAM, 1" ID, 16" LONG (S/N: & Above) A 1 WELD, HANDLE MOTION CNTRL,19.0,1.0,LH,BLK (S/N: & Above) A 1 WELD, HANDLE MOTION CNTRL,19.0,1.0,RH,BLK (Not Illustrated)(S/N: & Above) Footnotes 27

28 Hydraulic Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 28

29 Hydraulic Group REF NO PART NO. QTY. DESCRIPTION A 1 PLATE, HYD BOT FUEL MNT LH, S200XT - BLK A 1 PLATE, HYD BOT MOUNT, RH, S200XT - BLK X1 2 FITTING, BREATHER, ZT X7 2 LOOM, CONVOLUTED SPLIT, 1 ID LONG X9 2 HOSE, 5/8 PUSH LOCK, X6 4 BOLT, 5/16-18 X 3/4 GD5 CZ X8 4 BOLT, 1/4-20 X 1 GD5 CZ CLAMP, #10 HOSE, STAINLESS SPACER, ANTI ROTATE, ZT NUT, ZT WASHER, ZT5400, SLOTTED FAN, ZT PULLEY, ZT5400 (53177) TRANSAXLE, ZT5400, RH TRANSAXLE, ZT5400, LH HYDRO TANK, HYDRO-GEAR 71938, 1 LITER BOLT, 1/2-13 X 1-1/4, SF, PLT W/PATCH NUT, 5/16-18 HEX NYLOCK FLANGE NUT, 1/4-20 HEX NYLOCK FLANGE WASHER, 5/16 SAE Footnotes 29

30 Parking Brake Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 30

31 Parking Brake Group REF NO PART NO. QTY. DESCRIPTION CLEVIS, 5/16-24, STEEL, CLEAR ZINC BEARING, 3/4" FLANGED, BRONZE SWITCH, DP NO/NC SNAP-IN CABLE, PARKING BRAKE, S200XT NUT, 5/16-24 HEX NYLON LOCK WASHER, 5/16 SAE NUT, 3/8-16 HEX NYLOCK FLANGE SPACER,.32 X.75 X 1.06, PM SPRING, COMP. 1/2 ID X.140 WIRE X GRIP, FOAM, 3/4 ID X 6 X X6 4 BOLT, 3/8-16 X 3/4 GD5 CZ WASHER, 1/2 USS NUT, 5/16-18 HEX NYLOCK FLANGE NUT, 5/16-24 HEX X8 2 PIN, CLEVIS, 5/16 X 1, PLATED NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) X10 3 BOLT, 5/16-18 X 1-1/4 GD5 CZ SPACER,.38 X.50 X.31, CZ X14 2 BOLT, 5/16-18 X 1-3/4 GD5 CZ BUSHING, DECK PIVOT A 1 WELD, BRAKE SHAFT - BLK A 2 PLATE, BRAKE ARM EXTENSION - BLK A 2 LINK, BRAKE LOCK - BLK SPRING-COMP,.930IDX5.00LGX.085WR - BLK X10 2 BOLT, 1/2-13 X 1-1/4 GD5 CZ NUT, 1/2-13 HEX SIDE LOCK X6 2 PIN, COTTER, 1/8 X 3/ WASHER, 3/8 SAE X10 2 BOLT, 3/8-16 X 1-1/4 GD5 CZ COLLAR, 5/16 SET Footnotes 31

32 Deck Lift Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 32

33 Deck Lift Group REF NO PART NO. QTY. DESCRIPTION NUT, 3/8-16 HEX NYLOCK FLANGE BUSHING, 1.00 X 1.13 X 1.38, PLASTIC GREASE FITTING, 1/4-28 STRAIGHT GRIP, FOAM,.475 X 4.35 X SPRING-EXT,.500 OD X 3.50 LG X.058 WR PIN, HITCH, 1/2 X 2.00 OAL, CZ X12 2 BOLT, 3/8-16 X 1-1/2 GD5 CZ BALL JOINT, 1/2-20, MALE NUT, 1/2-20 HEX JAM SPRING-EXT, 1.00 ODX13.25LGX.177WR, BLK NUT, 3/8-16 HEX SERRATED FLANGE PEDAL, RUBBER X10 2 BOLT, 3/8-16 X 1-1/4 GD5 CZ SPACER,.52 X 1.00 X.22, PM, CZ ROD, DECK LIFT, TWR A 1 WELD, ROD DECK LIFT - BLK B 1 WELD, DECK ADJUST LINK - RED WASHER, 3/8 SAE WASHER,.390 X 1.50 X.109, CZ BOLT, 3/8-16 X 3/4, PLT W/PATCH NUT, 1/2-13 HEX NYLOCK FLANGE A 1 WELD, PIVOT, DECK LIFT, RH - 200XT A 1 WELD, PIVOT, DECK LIFT, LH - 200XT - BLK CLEVIS, 1/2-20, STEEL, CLEAR ZINC X12 4 PIN, CLEVIS, 1/2 X 1-1/2, PLATED X6 4 PIN, COTTER, 1/8 X 3/ A 1 PEDAL, FOOT - BLK WASHER, 3/8 GD.9 FLAT A 2 WELD, DECK STABILIZER, IS2500Z BLK B 1 WELD, DECK LIFT SHAFT, 200XT-61 - RED PIVOT BLOCK, PLASTIC A 2 PLATE, PIVOT BLOCK SUPPORT - BLK X22 4 BOLT, 3/8-16 X 2-3/4 GD5 CZ X8 4 BOLT, 3/8-16 X 1 GD5 CZ X10 1 BOLT, 1/2-13 X 1-1/4 GD5 CZ BALL JOINT, 3/4-16, MALE X20 4 BOLT, 3/4-16 X 2-1/2 GD8 CZ NUT, 3/4-16 HEX NYLON LOCK WASHER, 3/4 SAE NUT, 3/4-16 HEX JAM NUT, 3/8-16 HEX JAM Footnotes 33

34 Transaxle SERVICE PARTS - ZT5400 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 34

35 Transaxle SERVICE PARTS - ZT5400 REF NO PART NO. QTY. DESCRIPTION X5 1 AXLE CAP, ZT5400 (Hydro-Gear P/N 53724) X2 1 KIT, FILTER (Hydro-Gear P/N 71943) X4 1 KIT, SEAL, ZT5400 (Hydro-Gear P/N 71945) X6 1 KIT, CONTROL ARM SEAL (Hydro-Gear P/N 52989) X8 1 KIT, INPUT SHAFT (BEARING AND SHAFT ONLY) (Hydro-Gear P/N 71941) X7 1 KIT, INPUT SEAL (Hydro-Gear P/N 51280) X6 1 ASSM, HUB, STANDARD AXLE TRANSMISSIONS (ZT5400) (Hydro-Gear P/N 72039) X1 1 ASSM, HUB, LONG AXLE TRANSMISSIONS (ZT5400) (Hydro-Gear P/N 72102) X5 1 KIT, AXLE SEAL (Hydro-Gear P/N 53008) Footnotes 35

36 Wheel & Tire Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 36

37 Wheel & Tire Group REF NO PART NO. QTY. DESCRIPTION TIRE ASSM, 13 X 6.5-6, FF / TB SX2 4 BEARING, TAPERED CONE SX3 4 SEAL, GREASE BEARING ADJUSTER, SPACER, LG NUT, BEARING ADJUSTER, AXLE DEBRIS, COVER, CASTER WHEELS WASHER, 1/2 SAE X72 2 BOLT, 1/2-13 X 9 GD5 CZ NUT, 1/2-13 HEX NYLOCK FLANGE SX4 2 RACE, BEARING TIRE/WHEEL ASM, 24X , TURF SMART X1 2 TIRE, 24X , TURF SMART (SV) WHEEL, 12 X 8.5, SOLID NUT, 1/2-20, FOR WHEEL BOLT SILVER Footnotes 37

38 Decal Group - Safety & Operation USA Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 38

39 Decal Group - Safety & Operation USA Models REF NO PART NO. QTY. DESCRIPTION DECAL, MAIN SAFETY DECAL, PINCH POINT DECAL, DANGER DO NOT OPERATE W/O DEFLECT DECAL, WARNING, HAND IN BELT, ENG ONLY DECAL, MANUAL AVAIL IN SPANISH DECAL, WARNING, ROLL BAR DECAL, TRANSAXLE RELEASE, S200XT DECAL, FUEL VALVE DECAL, THROTTLE CONTROL DECAL, WARNING, FOLDING ROPS (SV) DECAL, WARNING & CAUTION, ROPS (SV) DECAL, IGNITION SWITCH DECAL, HYDRAULIC OIL, SAE 20W DECAL, FUSE LOCATION, IS DECAL, DECK HEIGHT, 1-1/2 TO 6, S200XT DECAL, BELT & BLADE, S200XT DECAL, CAUTION. FOLDING ROPS (SV) Footnotes 39

40 Decal Group - Brand & Model NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 40

41 Decal Group - Brand & Model REF NO PART NO. QTY. DESCRIPTION DECAL, FERRIS LOGO, SMALL DECAL, DECAL, icd CUTTING SYSTEM DECAL, MODEL, F210Z DECAL, FERRIS, 2.23" X 11.39" DECAL, TANK, MED, LH, FERRIS DECAL, TANK, MED, RH, FERRIS Footnotes 41

42 Decal Group - Safety & Operation Export Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 42

43 Decal Group - Safety & Operation Export Models REF NO PART NO. QTY. DESCRIPTION DECAL, MAIN SAFETY, ANSI CE DECAL, PINCH POINT, CE DECAL, CE DANGER (Located near the transmission fans.) DECAL, DISCHARGE SAFETY, EXPORT DECAL, PARKING BRAKE SYMBOLS DECAL, WARNING, ROLL BAR, CE (Located behind ROPS on the frame of the unit.) DECAL, TRANSAXLE RELEASE, S200XT (Located on bottom side of the seat plate.) DECAL, FUEL VALVE DECAL, THROTTLE CONTROL DECAL, SAFETY, CE ROPS DECAL, SAFETY, CE ROPS, OBS DECAL, IGNITION SWITCH DECAL, HYDRAULIC OIL, 20W50 (Located on bottom side of the seat plate.) DECAL, FUSE LOCATION, IS2100 (Located by fuse block.) DECAL, DECK HEIGHT, 1-1/2 TO 6, S200XT DECAL, BELT & BLADE, S200XT (Located on bottom side of the seat plate.) DECAL, FIRE ANSI EXPORT (Located on the instrument control panel.) Footnotes 43

44 Evap Canister Group - CAL Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 44

45 Evap Canister Group - CAL Models REF NO PART NO. QTY. DESCRIPTION CNSTR, CARB, 6 GAL CLAMP, 3" ID, CUSHIONED, STAINLESS X6 4 SCREW,1/4-20X3/4, ZINC PHOS & OIL NUT, 1/4-20 HEX NYLOCK FLANGE A 1 PLATE, CARB CAN, S200XT, RH - BLK A 1 PLATE, CARB CAN, S200XT, LH - BLK X10 4 BOLT, 5/16-18 X 1-1/4 GD5 CZ WASHER, 5/16 LOCK CZ NUT, 5/16-18 HEX NYLOCK FLANGE FITTING, 3/16" TEE, BARB TYPE, HDPE HOSE, FORMED, EVAP CANISTER CLAMP, HOSE FITTING, STRAIGHT, 10MMX10MM, PLASTIC X10 2 HOSE, VAPOR, 5MM ID, LG X50P5 1 HOSE, VAPOR, 5MM ID, LG (Briggs & Stratton Engines) X29 1 HOSE, VAPOR, 5MM ID, LG (Briggs & Stratton Engines) X9 1 HOSE, VAPOR, 5MM ID, 9.00 LG (Briggs & Stratton Engines) X18P5 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Engines) X47 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Engines) X24 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Engines) TIE, SELF-LOCKING, 15" TIE, SELF-LOCKING, 12" DUST FILTER, CANISTER (SV) Footnotes 45

46 61" Mower Deck - Housing, Covers, Spindles & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 46

47 61" Mower Deck - Housing, Covers, Spindles & Blades REF NO PART NO. QTY. DESCRIPTION A 1 SUPPORT, DISCHARGE CHUTE - BLK CHUTE, RUBBER DISCHARGE ( ) X12 3 BOLT, 3/8-16 X 1-1/2, CARRIAGE, GD5, CZ NUT, 3/8-16 HEX NYLOCK FLANGE A 1 WELD, MOUNT, DISCHARGE CHUTE - BLK NUT, 5/16-24 HEX NYLON LOCK ROD, MOUNT, CHUTE 61, CZ B 1 GUARD, RH S200XT - RED B 1 GUARD, 61 - LH - RED NUT, 5/16-18 HEX NYLOCK FLANGE SCREW, 5/16-18x0.750, GR5, WHIZ-LOCK, ZC WASHER, BLADE BOLT, 9/16" F436, CZ BODY CLIP, 5/ GA MATERIAL X6 6 BOLT, 5/16-18 X 3/4 GD5 CZ S 1 BLADE SET, 61 DECK (3) (SV)(Set of 3 blades) X14 3 BOLT, 5/8-11 X 1-3/4 GD8 (Torque to 70 ft. lbs (94 Nm) WASHER, 5/16 SAE A 1 PLATE, DEFLECTOR - BLK X8 18 BOLT, 3/8-16 X 1, FLANGE, GD 5, CZ (Torque to 30 ft. lbs. (41 Nm) DECK SHELL W/DECALS, F210Z-DOM ( B) SPINDLE, ASSM, CAST IRON B 1 PLATE, BRACKET, ANTI SCALP, RH RED WASHER, 3/8 SAE X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE X10 4 BOLT, 3/8-16 X 1-1/4 GD5 CZ SAFETY WALK, 9.75 X A 1 PLATE, SUPPORT - BLK FLAP, STRIPER, 61 DECK, IS3100 S200X X8 6 BOLT, 5/16-18 X 1 GD5 CZ /16 PUSH-ON NUT RETAINER, STL, CZ Footnotes 47

48 61" Mower Deck Group - Rollers & Casters NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 48

49 61" Mower Deck Group - Rollers & Casters REF NO PART NO. QTY. DESCRIPTION WHEEL WIDE 3.88 DIA 0.531ID POLY WASHER, 1/2 GD9 YZ SPACER,.38 X.50 X NUT, 3/8-16 HEX SIDELOCK X24 2 BOLT, 3/8-16 X 3 GD5 YZ WASHER, 3/8 SAE SPACER,.38 X.50 X SPACER,.51 X.75 X X48 2 BOLT, 3/8-16 X 6 GD5 YZ Footnotes 49

50 61" Mower Deck - Hanger Chains NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 50

51 61" Mower Deck - Hanger Chains REF NO PART NO. QTY. DESCRIPTION NUT, 3/8-16 HEX SERRATED FLANGE WASHER, 3/8 SAE X14 6 BOLT, 3/8-16 X 1-3/4 GD X16 2 BOLT, 3/8-16 X 2 GD5 YZ X16 2 BOLT, 5/16-18 X 2 GD5 TFL NUT, 5/16-18 HEX CLEVIS, 5/16-18, 3/8 PIN HOLE X9 2 PIN, CLEVIS, 3/8 X 1-1/ PIN, 3/32 X.750, COT, ZINC/CLEAR X3 2 CHAIN, 5/16 GD30, 3 LINKS X2 2 CHAIN, 5/16 GD30, 2 LINKS NUT, 3/8-16 HEX JAM Footnotes 51

52 61" Mower Deck - Pulleys, Belt & Idler Arm NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 52

53 61" Mower Deck - Pulleys, Belt & Idler Arm REF NO PART NO. QTY. DESCRIPTION NUT, 1/2-13 HEX NYLOCK FLANGE A 1 WELD, IDLER ARM, CUTTER DECKS - BLK BEARING, /2", SEALED SPACER,.510 X.750 X 1.749, CZ SPACER, IDLER ARM, 1/2 X SPRING, EXT, 1.5ODX12.25X.234WIRE BLK PULLEY, FLAT IDLER, 6-3/4" IDLER MOUNT PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID SPACER,.52 X 1.00 X.56, PM, CZ SHIELD, PULLEY BEARING, CZ PULLEY, SPIN, 6.5 OD X 25MM, SPACER,.52 X 1.00 X SPACER,.39 X.75 X.38, PM, CZ X10 3 KEY, 1/4 SQ X 1-1/4 (Not Shown) EYE BOLT, 3/8-16 X 4, 2.13THRD, 1 EYE,CZ BELT, 5V, "EL, LG ARAMID WRPD, RC WASHER, 3/4 BELLEVILLE NUT, 3/4-16 HEX X36 1 BOLT, 1/2-13 X 4-1/2 GD5 CZ X28 1 BOLT, 3/8-16 X 3-1/2 GD5 CZ WASHER-3/8 FENDER NUT, 3/8-16 HEX NYLOCK FLANGE NUT, 3/8-16 HEX X18 1 BOLT, 1/2-13 X 2-1/4 GD5 CZ X24 3 BOLT, 1/2-13 X 3 GD5 CZ Footnotes 53

54 Spindle Service Parts NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 54

55 Spindle Service Parts REF NO PART NO. QTY. DESCRIPTION FITTING SHIELD, TRASH BEARING,.98 X 2.44 X FITTING, RELIEF, 1-5 PSI HOUSING, SPINDLE, BOTTOM MOUNT SM SPACER SHAFT, SPINDLE SPINDLE ASSM, CAST IRON BOLT (Includes Ref No. 1-7) Footnotes 55

56 Electrical Group - Kawasaki S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 56

57 Electrical Group - Kawasaki S/N: & Below REF NO PART NO. QTY. DESCRIPTION COVER, VINYL FUSEBLOCK FUSE, ATO-15 (15 AMP)(SV) FUSE, ATO-20 (20 AMP)(SV) X16 2 SCREW, #10-24 X 2 ROUND PHILLIPS WASHER, #10 SAE X17 1 WIRE LOOM, 3/8 ID X 17 IN NUT, #10-24 HEX NYLON LOCK BATTERY, WET ( BCIU1, 350 CCA) STRAP-BLACK RUBB BATTERY CABLE, NEG, 14, 5/16-13/ BATTERY CABLE, POS, 22, 1/4-5/ WIRE HARNESS, S200XT KAWI FX NUT, 1/4-20 HEX NYLOCK FLANGE CLAMP, VINYL INSULATED, RELAY, 12V, 40A X6 6 BOLT, 1/4-20 X 3/4 GD5 CZ WASHER, 1/4 SAE NUT, 1/4-20 HEX SERR. FLANGE MODULE, TIME DELAY SWITCH, PLUNGER, NO, SINGLE POLE, SNAP-IN (SEAT SWITCH) SWITCH, PLUNGER, N.O., BOLT-ON (NEUTRAL SWITCH) X6 5 SCREW, #10-24 X 3/4 ROUND PHILLIPS NUT, #10-24 HEX SWITCH, DP NO/NC SNAP-IN (PARKING BRAKE SWITCH) TIE, SELF-LOCKING, 12" SWITCH, IGNITION, 6 POST (SEE INSTRUMENT CONTROL PANEL GROUP) SWITCH, BLADE ENGAGEMENT (SEE INSTRUMENT CONTROL PANEL GROUP) HOUR METER (SEE INSTRUMENT CONTROL PANEL GROUP) Footnotes 57

58 Electrical Group - Briggs & Stratton EFI S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 58

59 Electrical Group - Briggs & Stratton EFI S/N: & Below REF NO PART NO. QTY. DESCRIPTION COVER, VINYL FUSEBLOCK FUSE, ATO-15 (15 AMP)(SV) FUSE, ATO-20 (20 AMP)(SV) X16 2 SCREW, #10-24 X 2 ROUND PHILLIPS WASHER, #10 SAE X17 1 WIRE LOOM, 3/8 ID X 17 IN NUT, #10-24 HEX NYLON LOCK BATTERY, WET ( BCIU1, 350 CCA) STRAP-BLACK RUBB BATTERY CABLE, NEG, 14, 5/16-13/ BATTERY CABLE, POS, 22, 1/4-5/ WIRE HARNESS, S200XT, B&S EFI NUT, 1/4-20 HEX NYLOCK FLANGE CLAMP, VINYL INSULATED RELAY, 12V, 40A X6 6 BOLT, 1/4-20 X 3/4 GD5 CZ WASHER, 1/4 SAE NUT, 1/4-20 HEX SERR. FLANGE LAMP, MALFUNCTION INDICATOR LAMP (M.I.L.) (SEE INSTRUMENT CONTROL PANEL GROUP) SWITCH, PLUNGER, NO, SINGLE POLE, SNAP-IN (SEAT SWITCH) SWITCH, PLUNGER, N.O. (NEUTRAL SWITCH) X6 5 SCREW, #10-24 X 3/4 ROUND PHILLIPS NUT, #10-24 HEX SWITCH, DP NO/NC SNAP-IN (PARKING BRAKE SWITCH) TIE, SELF-LOCKING, 12" SWITCH, IGNITION, 6 POST (SEE INSTRUMENT CONTROL PANEL GROUP) SWITCH, BLADE ENGAGEMENT (SEE INSTRUMENT CONTROL PANEL GROUP) HOUR METER (SEE INSTRUMENT CONTROL PANEL GROUP) Footnotes 59

60 Electrical Group - Briggs & Stratton EFI S/N: & Above NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 60

61 Electrical Group - Briggs & Stratton EFI S/N: & Above REF NO PART NO. QTY. DESCRIPTION COVER, VINYL FUSEBLOCK FUSE, ATO-15 (15 AMP) (SV) FUSE, ATO-20 (20 AMP) (SV) BATTERY, WET ( BCIU1, 350 CCA) STRAP-BLACK RUBB RELAY, 12V, 40A BATTERY CABLE, POS, 22, 1/4-5/ BATTERY CABLE, NEG, 22, 1/4-5/ GROMMET, 2" ID X17 1 WIRE LOOM, 3/8 ID X 17 IN X6 6 BOLT, 1/4-20 X 3/4 GD5 CZ WASHER, 1/4 SAE CLAMP, VINYL INSULATED, NUT, 1/4-20 HEX NYLOCK FLANGE WIRE HARNESS, 28HP BRIGGS EFI, F210/320Z TIE, SELF-LOCKING, 8", PUSH MOUNT TIE, SELF-LOCKING, 12" NUT, 1/4-20 HEX SERR. FLANGE X6 10 SCREW, #10-24 X 3/4 ROUND PHILLIPS NUT, #10-24 HEX NYLON LOCK CLAMP, VINYL INSULATED, SWITCH, PLUNGER, N.O., BOLT-ON CONTROL SWITCHES (SEE INSTRUMENT CONTROL PANEL GROUP) SWITCH, PLUNGER, N.C SWITCH, DP NO/NC SNAP-IN Footnotes 61

62 Electrical Group - Kawasaki S/N: & Above NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 62

63 Electrical Group - Kawasaki S/N: & Above REF NO PART NO. QTY. DESCRIPTION COVER, VINYL FUSEBLOCK FUSE, ATO-15 (15 AMP) (SV) FUSE, ATO-20 (20 AMP) (SV) BATTERY, WET ( BCIU1, 350 CCA) STRAP-BLACK RUBB RELAY, 12V, 40A BATTERY CABLE, POS, 22, 1/4-5/ BATTERY CABLE, NEG, 22, 1/4-5/ GROMMET, 2" ID X17 1 WIRE LOOM, 3/8 ID X 17 IN X6 6 BOLT, 1/4-20 X 3/4 GD5 CZ WASHER, 1/4 SAE CLAMP, VINYL INSULATED, NUT, 1/4-20 HEX NYLOCK FLANGE WIRE HARNESS, 35HP KAV, F320Z TIE, SELF-LOCKING, 8", PUSH MOUNT TIE, SELF-LOCKING, 12" NUT, 1/4-20 HEX SERR. FLANGE X6 11 SCREW, #10-24 X 3/4 ROUND PHILLIPS NUT, #10-24 HEX NYLON LOCK CLAMP, VINYL INSULATED, SWITCH, PLUNGER, N.O., BOLT-ON CONTROL SWITCHES (SEE INSTRUMENT CONTROL PANEL GROUP) SWITCH, PLUNGER, N.C SWITCH, DP NO/NC SNAP-IN MODULE, TIME DELAY Footnotes 63

64 Electrical Schematic - Charging Circuit - Kawasaki S/N: & Below - F2 - F2 64

65 Electrical Schematic - Cranking Circuit - Kawasaki S/N: & Below - F2 - F2 65

66 Electrical Schematic - PTO Clutch Circuit - Kawasaki S/N: & Below - F2 - F2 66

67 Electrical Schematic - Ign. Ground Circuit/Op. Pres. - Kawasaki S/N: & Below - F2 - F2 67

68 Electrical Schematic - Charging Circuit - B&S EFI S/N: & Below - F2 - F2 68

69 Electrical Schematic - Cranking Circuit - B&S EFI S/N: & Below - F2 - F2 69

70 Electrical Schematic - PTO Clutch Circuit - B&S EFI S/N: & Below - F2 - F2 70

71 Electrical Schematic - Ign. Ground Circuit/Op. Pres. - B&S EFI S/N: & Below - F2 - F2 71

72 Electrical Schematic - Charging Circuit - Kawasaki S/N: & Above - F2 - F2 72

73 Electrical Schematic - Cranking Circuit - Kawasaki S/N: & Above - F2 - F2 73

74 Electrical Schematic - PTO Clutch Circuit - Kawasaki S/N: & Above - F2 - F2 74

75 Electrical Schematic - Ign. Ground Circuit/Op. Pres. - Kawasaki S/N: & Above - F2 - F2 75

76 Electrical Schematic - Charging Circuit - B&S EFI S/N: & Above - F2 - F2 - F2 76

77 Electrical Schematic - Cranking Circuit - B&S EFI S/N: & Above - F2 - F2 - F2 77

78 Electrical Schematic - PTO Clutch Circuit - B&S EFI S/N: & Above - F2 - F2 - F2 78

79 Electrical Schematic - Ign. Ground Circuit/Op. Pres. - B&S EFI S/N: & Above - F2 - F2 - F2 79

80 Notes

81 Notes

82

83 Hardware Identification & Torque Specifications Common Hardware Types Hex Head Capscrew Washer Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Carriage Bolt Lockwasher Hex Nut Standard Hardware Sizing When a washer or nut is identified as 1/2, this is the Nominal size, meaning the inside diameter is 1/2 inch; if a second number is present it represent the threads per inch When bolt or capscrew is identified as 1/2-16 x 2, this means the Nominal size, or body diameter is 1/2 inch; the second number represents the threads per inch (16 in this example, and the final number is the body length of the bolt or screw (in this example 2 inches long). The guides and ruler furnished below are designed to help you select the appropriate hardware and tools. 0 1/4 1/2 3/4 1 1/4 1/2 3/4 2 1/4 1/2 3/4 3 1/4 1/2 3/4 Screw, 1/2 x 2 Body Diameter Body Length Nut, 1/2 Inside Diameter Hardware Grade No Marks SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm / / / / / / / / / / / / / / / / / / , ,000 1,360.0 NOTES 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. for prevailing torque locknuts - use 65% of grade 5 torques. b. for flange whizlock nuts and screws - use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings, all torque values must meet this specification. 4 Wrench & Fastener Size Guide 1/4 5/16 3/8 7/16 DIA. 1/2 DIA. 1/4 Bolt or Nut Wrench 7/16 5/16 Bolt or Nut Wrench 1/2 3/8 Bolt or Nut Wrench 9/16 7/16 Bolt or Nut Wrench (Bolt) 5/8 Wrench (Nut) 11/16 1/2 Bolt or Nut Wrench 3/4

84 Parts Manual F210Z Series Zero-Turn Riding Mower IT IS THE POLICY OF BRIGGS STRATTON TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED Briggs and Stratton Power Products Group, LLC North Main Street Munnsville, NY USA Copyright 2017 Briggs and Stratton Corporation All Rights Reserved. Printed In USA.