Parts List for all Sentar Sport models For Sentar Sport serial #33615 and higher until superseded

Transcription

1 Parts List for all Sentar Sport models For Sentar Sport serial #33615 and higher until superseded WRIGHT MANUFACTURING, INC X WEDGEWOOD BLVD - FREDERICK, MD Revised 01/2007

2 36" CUTTER DECK REF. # DESCRIPTION PART # 1 36" CUTTER DECK w/ # A REAR DISCHARGE CUTTER DECK " DECK COVER KNOB, DECK A 3/8-24 NYLOCK NUT (CE MODEL) BOLT, HCS, 1/4-20X1 PLAIN BUSHING SPLIT TAPERED X 7/8" PULLEY, SINGLE GRV PULLEY, SMALL IDLER, DECK BELT, WRAPPED NUT, TOPLOCK 3/ WASHER, FLAT USS 5/16 z NUT, LOCK FLANGE 3/8-24 Z T-ROD, DECK COVER STAND CAP, VINYL 3/8 X 1, FOR ISO POSTS BOLT, HCS, 1/2-20X3.5 Z WASHER, FENDER 5/16 X 1 1/4 Z BEARING, BALL, FOR IDLER ARM CIS BEARING BUSHING SPRING, 2.5" DECK IDLER SPRING IDLER ARM ASSEMBLY, LEFT, 7" BOLT, HEX 3/8-16 X 2 1/2 Z MACH BUSH, 1/2 ID X 7/8 OD X 18 GA IDLER ARM WASHER NUT, NYLOCK 1/2-20 Z BOLT, FLANGE 1/2-13 X 1 1/4 Z NUT, LOCK FLANGE 1/2-13 Z BOLT, FLANGE 3/8-16 X 1 Z NUT, TOPLOCK 3/ BLADE, 18" WASHER, FLAT USS 5/8 Z BOLT, HEX 5/8-18 X 1 1/2 Z SPINDLE, LONG SHAFT RETAINING RING, EXTERNAL (SMALL) WASHER, SMALL FOR SPINDLE BEARING, SPINDLE (LARGE) SPINDLE HOUSING BEARING, SPINDLE (SMALL) SPINDLE SHAFT, LONG SHAFT MACHINE KEY 3/16 X 3/16 X NUT, NYLOCK 5/16-18 Z SPRING, TORSION FOR CHUTE DEFLECTOR BOLT, HEX 5/16-18 X 4 1/2 Z BOLT, CARRIAGE 3/8 X 1 Z FLEXIBLE CHUTE DEFLECTOR CLAMP PLATE CHUTE DEFLECTOR, RUBBER FLEXIBLE CHUTE DEFLECTOR FLANGE BOLT, HEX 5/16-18 X 1 Z MULCHING BLOCK OFF PLATE w/ HARDWARE NUT, LOCK FLANGE 3/8-16 Z GRASS GOBBLER FOR WRIGHT (JUMBO) INCL 50,51 WRJ LATCH GGL DOOR (JUMBO SIZE) GGD LEAF GOBBLER LG MULCH KIT, CURVED, 36" A MULCH BAFFLE CURVED, 36" CHUTE DEFLECTOR KIT, FLEXIBLE " LEFT RD BAFFLE " RIGHT RD BAFFLE BOLT, HEX 5/16-18 X 3/4 Z Wright Manufacturing, Inc. All rights reserved.

3

4 42" CUTTER DECK REF. # DESCRIPTION PART # 1 42" CUTTER DECK w/ # " DECK COVER KNOB, DECK A 3/8-24 NYLOCK NUT (CE MODEL) BOLT, HCS, 1/4-20X1 PLAIN BUSHING SPLIT TAPERED X 7/8" PULLEY, SINGLE GRV PULLEY, IDLER, DECK BELT, WRAPPED NUT, TOPLOCK 3/ WASHER, FLAT USS 3/8 x 1 1/ NUT, LOCK FLANGE 3/8-24 Z T-ROD, DECK COVER STAND CAP, VINYL 3/8 X 1, FOR ISO POSTS BOLT, HCS, 1/2-20X3.5 Z WASHER, FENDER 5/16 X 1 1/4 Z BEARING, BALL, FOR IDLER ARM CIS BEARING BUSHING SPRING, 2.5" DECK IDLER SPRING IDLER ARM ASSEMBLY, LEFT, 7" BOLT, HEX 3/8-16 X 2 3/4 Z MACH BUSH, 1/2 ID X 7/8 OD X 18 GA IDLER ARM WASHER NUT, NYLOCK 1/2-20 Z BOLT, FLANGE 1/2-13 X 1 1/4 Z NUT, LOCK FLANGE 1/2-13 Z BOLT, FLANGE 3/8-16 X 1 Z NUT, TOPLOCK 3/ BLADE, 21" WASHER, FLAT USS 5/8 Z BOLT, HEX 5/8-18 X 1 1/2 Z SPINDLE, LONG SHAFT RETAINING RING, EXTERNAL (SMALL) WASHER, SMALL FOR SPINDLE BEARING, SPINDLE (LARGE) SPINDLE HOUSING BEARING, SPINDLE (SMALL) SPINDLE SHAFT, LONG SHAFT MACHINE KEY 3/16 X 3/16 X NUT, NYLOCK 5/16-18 Z SPRING, TORSION FOR CHUTE DEFLECTOR BOLT, HEX 5/16-18 X 4 1/2 Z BOLT, CARRIAGE 3/8 X 1 Z FLEXIBLE CHUTE DEFLECTOR CLAMP PLATE CHUTE DEFLECTOR, RUBBER FLEXIBLE CHUTE DEFLECTOR FLANGE BOLT, HEX 5/16-18 X 1 Z MULCHING BLOCK OFF PLATE w/ HARDWARE NUT, LOCK FLANGE 3/8-16 Z GRASS GOBBLER FOR WRIGHT (JUMBO) INCL 50,51 WRJ LATCH GGL DOOR (JUMBO SIZE) GGD LEAF GOBBLER LG MULCH KIT, CURVED, 42" CHUTE DEFLECTOR KIT, FLEXIBLE BORE ADAPTER, 30MM X 41MM Wright Manufacturing, Inc. All rights reserved.

5

6 48", 52" CUTTER DECKS REF. # DESCRIPTION PART # 1 48" CUTTER DECK W/ ISOL. CAPS A 52" CUTTER DECK W/ ISOL. CAPS B 52" REAR DISCHARGE DECK W/ ISOL. CAPS " DECK COVER, LEFT A 52" DECK COVER, LEFT " DECK COVER, RIGHT A 52" DECK COVER, RIGHT KNOB, DECK A 3/8-24 NYLOCK NUT (CE MODEL) BOLT, HCS, 1/4-20X1 PLAIN BUSHING SPLIT TAPERED X 7/8" PULLEY, SINGLE GRV (48" DECK) A PULLEY, SINGLE GRV (52" DECK) PULLEY, DOUBLE GRV (48" DECK) A PULLEY, DOUBLE GRV (52" DECK) PULLEY, SMALL IDLER, DECK BELT, WRAPPED (48" DECK) A BELT, WRAPPED (52" DECK) BELT, WRAPPED (48" DECK) A BELT, WRAPPED (52" DECK) NUT, LOCK FLANGE 3/8-24 Z T-ROD, DECK COVER STAND BOLT, HCS, 1/2-20X3.5 Z WASHER, FENDER 5/16 X 1 1/4 Z BEARING, BALL, FOR IDLER ARM, NEW CIS BEARING BUSHING SPRING, 2.5" DECK IDLER SPRING IDLER ARM ASSEMBLY, RIGHT, 7" IDLER ARM ASSEMBLY, LEFT, 7" MACH BUSH, 1/2 ID X 7/8 OD X 18 GA IDLER ARM WASHER BOLT, HEX 3/8-16 X 2 Z BOLT, HEX 3/8-16 X 2 1/2 Z NUT, TOPLOCK 3/ WASHER, FLAT USS 5/16 z BOLT, FLANGE 1/2-13 X 1 1/4 Z NUT, LOCK FLANGE 1/2-13 Z CAP, VINYL FOR ISO POSTS BOLT, FLANGE 3/8-16 X 1 Z NUT, TOPLOCK 3/ BLADE, 16 1/2" (48" DECK) A BLADE, 18" (52" DECK) WASHER, FLAT USS 5/8 Z BOLT, HEX 5/8-18 X 1 1/2 Z SPINDLE, LONG SHAFT RETAINING RING, EXTERNAL (SMALL) WASHER, SMALL FOR SPINDLE BEARING, SPINDLE (LARGE) SPINDLE HOUSING BEARING, SPINDLE (SMALL) SPINDLE SHAFT, LONG SHAFT MACHINE KEY 3/16 X 3/16 X NUT, NYLOCK 1/2-20 Z BOLT, HCS, 5/8-11 X 4 1/ WHEEL, PLASTIC, ANTI-SCALP NUT, LOCK FLANGE 5/8-11 Z NUT, NYLOCK 5/16-18 Z SPRING, TORSION FOR CHUTE DEFLECTOR BOLT, HEX 5/16-18 X 4 1/2 Z BOLT, CARRIAGE 3/8 X 1 Z FLEXIBLE CHUTE DEFLECTOR CLAMP PLATE CHUTE DEFLECTOR, RUBBER FLEXIBLE CHUTE DEFLECTOR FLANGE BOLT, HEX 5/16-18 X 1 Z MULCHING BLOCK OFF PLATE w/ HARDWARE NUT, LOCK FLANGE 3/8-16 Z GRASS GOBBLER FOR WRIGHT (JUMBO), INCL 58,59 WRJ LATCH GGL DOOR (JUMBO SIZE) GGD LEAF GOBBLER LG MULCH KIT, CURVED, 48" A MULCH BAFFLE,CURVED, RIGHT,48" B MULCH BAFFLE,CURVED, LEFT,48" MULCH KIT, CURVED, 52" A MULCH BAFFLE,CURVED, RIGHT,52" B MULCH BAFFLE,CURVED, LEFT,52" CHUTE DEFLECTOR KIT, FLEXIBLE /8-11 TOPLOCK NUT /8 X 1 3/8 FLAT WASHER DECK BAFFLE KIT, 48", W/ HARDWARE DECK BAFFLE KIT, 52", W/ HARDWARE Wright Manufacturing, Inc. All rights reserved.

7

8 ENGINE DECK COMPONENTS REF. # DESCRIPTION PART # 1 ENGINE, OBTAIN FROM AUTHORIZED ENGINE DEALER N/A 2 HYDRO PUMP LEFT HYDRO PUMP RIGHT PUMP CONTROL LEVER, LEFT PUMP CONTROL LEVER, RIGHT BOLT, CARRIAGE 7/16-14 X 1 Z BOLT, FLANGE 5/16-18 X 3/4 Z WASHER, FLAT 1/4 Z NUT, LOCK FLANGE 5/16-18 Z SCREW, ROUND PHLP 1/4-20 X 2 Z CIS BEARING BUSHING HARNESS, MAIN, ELECTRIC W/ PTO DELAY HARNESS, ENGINE KAW 17 HP R/E & PUMP LOCK ACTUATOR MUFFLER GUARD, 17 & 19 HP KAI (CE MODEL) MUFFLER, W/BRACKET MUFFLER, BRACKET ONLY OBTAIN FROM AUTHORIZED KAWASAKI DEALER N/A 19 NUT, TOPLOCK 5/16-18Z WASHER, LOCK, MUFFLER MOUNTING NUT, HEX METRIC, MUFFLER MOUNTING O-RING, FOR KAWASAKI OIL DRAIN ADAPT OIL DRAIN VALVE ADAPTER OIL DRAIN VALVE FITTING, MALE BARB 1/ TUBE, OIL DRAIN BOLT, HEX 5/16-24 X 1 1/2 Z NUT, LOCK FLANGE 5/16-24 Z BOLT, HEX 1/4-20 X 1 Z IDLER ARM WASHER NUT, LOCK FLANGE 1/4-20 Z E-CLIP 1/ MACH BUSH, 1/2 ID X 7/8 OD X 18 GA PUMP LOCK LEVER SPRING, 2" CLIP, HALF 5/ BOLT, HEX 1/4-20 X 5/8 Z BOLT, HCS, 1/2-20X3.5 Z SWITCH, OPC, 2 LB INTERNAL SPRING, BLACK ENGINE DECK NUT, NYLOCK 1/4-20 Z NUT, LOCK FLANGE 7/16-14 Z ENGINE MUFFLER HEAT SHIELD BOLT, HEX 3/8-16 X 2 Z HYDRAULIC PUMP BELT PULLEY, A 5.25in SINGLE GROOVE H BORE PULLEY, IDLER 4 1/2 X 1 X 3/8 BORE MACHINE KEY 1/4 X 1/4 X PULLEY, 4.5 OD X A GRV X 1" (ENGINE) BUSHING SPLIT TAPERED X 15MM MACHINE KEY 5MM X 5MM X 25MM BOLT, HCS, 1/4-20X1 PLAIN CLUTCH / BRAKE SMALL SPACER, FOR CLUTCH WASHER, LOCK 7/16 Z BOLT, HEX 7/16-20 X 2 3/4 Z IDLER ARM ASSEMBLY, 7" NUT, TOPLOCK 3/ SPRING, 2.5" IDLER SPRING BEARING, BALL, FOR IDLER ARM WASHER, FENDER 5/16 X 1 1/4 Z NUT, NYLOCK 1/2-20 Z BOLT, HEX 1/2"-20 x 1 1/2" S.S. MACHINED PIN WASHER /2" LOW PROFILE NUT WATER-RESISTANT RELAY PTO CLUTCH TIME-DELAY MODULE CE MUFFLER GUARD HEAT SHIELD NUT, U 1/ ga WASHER, LOCK 1/4 Z SCREW, TRUSS HD MACH 1/4-20 X 3/4 SS MACH BUSH, 1/2 ID X 14 GA BOLT, SHLDR ALLEN 1/2 X 3/ BOLT-ON CLUTCH STOP Wright Manufacturing, Inc. All rights reserved.

9

10 UPRIGHT ASSEMBLY REF. # DESCRIPTION PART # 1 UPRIGHT HANDLEBAR GRIP, HANDLE BAR.625 X 11 X CONTROL LEVER ASSEMBLY-RIGHT CONTROL LEVER ASSEMBLY-LEFT HBUSH SHORT MACH BUSH, 1/2 ID X 7/8 OD X 18 GA NUT, NYLOCK, 5/16-24 Z ROD END, BALL JOINT - LEFT HAND THREAD NUT, LH JAM 5/16-24 Z T-ROD, PUMP CONTROL, SET NUT, JAM, HEX 5/16-24 Z ROD END, BALL JOINT NUT, LOCK FLANGE 5/16-18 Z IGNITION SWITCH, FOR ELECTRIC START SWITCH, BLADE ON/OFF, RED SCREW, TRUSS HD MACH X 1/ HOUR METER CHOKE CONTROL NUT, KEP Z THROTTLE CABLE E-CLIP 1/ BOLT, FLANGE 5/16-18 X 3/4 Z HYDRO OIL TANK GROOVE PIN,.5 X SCREW, PHLPS PAN X 3/4 Z WASHER, FLAT SAE #10 Z RELAY, FOR MAIN HARNESS NUT, NYLOCK BOLT, HEX 1/4-20 X 5/8 Z WASHER, LOCK 1/4 Z SOLENOID NUT, NYLOCK 1/4-20 Z HARNESS, GREEN JUMPER WIRE CABLE, BATTERY, RED 38" W/ LUG INSUL WASHER, LOCK 1/4 Z NUT, JAM 1/4-20 Z POSITIVE CABLE, BATTERY, RED GROUND CABLE, BATTERY, BLACK WIRE, GROUNDING HYDRO OIL FILTER HOUSING BLOCK HYDRO OIL FILTER PLUG, STEEL 3/ BOLT, FLANGE 3/8-16 X 3/4 Z NUT, LOCK FLANGE 3/8-16 Z Wright Manufacturing, Inc. All rights reserved.

11

12 MAIN FRAME REF. # DESCRIPTION PART # 1 TRACTOR BODY FOOT PLATFORM WASHER, FLAT USS 5/16 z NUT, LOCK FLANGE 3/8-24 Z NUT, NYLOCK JAM 1/2-20 Z WASHER, FLAT USS 7/16 Z T-ROD SWITCH, OPC, 2 LB INTERNAL SPRING OPC TRIGGER CABLE, BATTERY, BLACK 18 1/2" BOLT, FLANGE 5/16-18 X 3/4 Z SCREW, TRUSS HD PH 1/4-20 X 1/2 SS WASHER, FLAT 1/4 Z NUT, NYLOCK 1/4-20 Z BATTERY HOLD DOWN HARNESS, VELKE PG RECOIL CABLE, BATTERY, RED 38" W/ LUG INSUL NUT, LOCK FLANGE 5/16-18 Z OBTAIN FROM LOCAL BATTERY SUPPLIER N/A 20 FUEL TANK CAP W/ ADV VENT FUEL TANK FUEL TANK STRAP SCREW, ROUND PHLP 1/4-20 X 2 Z BUSHING FOR FUEL TANK VALVE VALVE, BALL 90 FOR FUEL TANK FUEL TANK PROTECTOR PLATE FUEL TANK STAND CASTER FRAME ASSEMBLY, 36" w/ ZERK CASTER FRAME ASSEMBLY, 42" w/ ZERK CASTER FRAME ASSEMBLY, 48", 52" w/ ZERK LYNCH PIN 7/16 FOR CASTERS MACH BUSH, 1 1/4 ID X 1 7/8 OD X 14 GA CASTER SPACER, NOTCHED C-TYPE BUSHING, CASTER, FOR 1 1/4 PIN BOLT, HEX 3/4-10 X 6 1/2 Z L-S CASTER YOKE NUT, NYLOCK JAM 3/4-10 Z ZERK, 1/4-28 (GREASE FITTING) GREASE FITTING FOR WHEEL VKWHLZERK 38 PNEUMATIC WHEEL ASSEMBLY, 11X FLAT-FREE WHEEL ASSEMBLY RIM ONLY (FOR PNEUMATIC ASSY) TIRE ONLY 11 X (FOR PNEUMATIC ASSY) SPACER, FOR CASTER WHEELS SEAL, FOR CASTER WHEELS BEARING, FOR CASTER WHEELS TAPERED ROLLER BEARING RACE BEARING KIT FOR 11X400-5 CASTER WHEEL BOLT, FLANGE 3/8-16 X 1 Z NUT, LOCK FLANGE 3/8-16 Z CLIP, HALF 5/ BOLT, CARRIAGE 7/16-14 X 1 Z NUT, LOCK FLANGE 5/8-11 Z WHEEL, PLASTIC, ANTI-SCALP BOLT, HCS, 5/8-11 X 4 1/ FOOT PLATE PIVOT, ZINC PLATE BOLT, HEX 1/2-20 X 2 1/4 Z HYDRO MOTOR, 12P WOODRUFF KEY 3/16 X 3/4 (FOR HYD MOTOR) WHEEL MOTOR SUPPORT, R&L WHEEL HUB, 36" DECK WHEEL HUB, 42", 48" & 52" DECK STUD FOR TAPERED HUB NUT, LOCK FLANGE 7/16-14 Z NUT, CASTLE, (FOR ) COTTER PIN 1/8 X NUT, LUG 1/ WHEEL ASSEMBLY, 18X8-10, (36", 42" DECK) WHEEL ASSY, (48", 52" DECK, PRE SERIAL 37617) WHEEL ASSY, (48", 52" DECK, POST SERIAL 37617) RIM ONLY (36",42" DECK) RIM ONLY, (48", 52" DECK, PRE SERIAL 37617) RIM ONLY, (48", 52" DECK, POST SERIAL 37617) TIRE ONLY, 48" & 52" PRE SERIAL TIRE ONLY, (ALL 32" & 42" 48" & 52" POST SER ) SPRING, LRG, COMPRESSION /8-11 TOPLOCK NUT /8 X 1 3/8 FLAT WASHER BATTERY COVER GROMMET, BATTERY CABLES WEIGHT BAR HOSE, FUEL HOSE CLAMP, 1/ FUEL FILTER Wright Manufacturing, Inc. All rights reserved.

13

14 DECK LIFT / PARKING BRAKE REF. # DESCRIPTION PART # 1 TRACTOR BODY KNEE PAD SUPPORT, KNEE PAD, LEFT SUPPORT, KNEE PAD, RIGHT BOLT, FLANGE 5/16-18 X 3/4 Z NUT, LOCK FLANGE 5/16-18 Z BOLT, FLANGE 3/8-16 X 3/4 Z BRAKE SHOE, PRE SERIAL BRAKE SHOE, POST SERIAL SPRING, PUMP IDLER NUT, LOCK FLANGE 3/8-16 Z BRAKE BAR FLANGE BOLT, 1/2-13 x 1 1/ MACH BUSH, 1/2 ID X 7/8 OD X 18 GA PUMP LOCK ACTUATOR E-CLIP 1/ HBUSH SMALL BRAKE PUSH BAR HANDLE GRIP FOR BRAKE BRAKE HANDLE w/ GRIP BOLT, HEX 3/8-16 X 1 1/2 Z SPRING, SPORT, DECK LIFT S.S. MACHINED PIN BOLT, HEX 3/8-16 X 2 Z WASHER, FLAT USS 5/16 z HOSE HOLD CLIP NUT, TOPLOCK 3/ NUT, LOCK FLANGE 1/4-20 Z NUT, NYLOCK 3/ DETENT PIN AND LANYARD WASHER, FLAT 1/4 Z BOLT, HEX 1/4-20 X 1 Z * DECK LIFT LINK MACHINED BUSHING, 14 GA, 1 1/4 ID /4" E-CLIP REAR DECK LIFT BUSHING DECK LIFT HANDLE SPACER GRIP, BLACK, 4.5" w/hole DECK LIFT HANDLE w/ GRIP BOLT, CARRIAGE 5/16-18 X 1 1/2" Z DECK LIFT HEIGHT COG AND LATCH KIT SPRING, DECK COG WASHER, FLAT, 7/ NUT, NYLOCK 1/ * DECK LIFT AXLE, REAR * DECK LIFT AXLE, FRONT DECK-LIFT HANGER, FRONT FRONT LIFT AXLE-3/4" FRONT LIFT AXLE BUSHING MACHINED BUSHING, 14 GA, 3/4 ID FLANGE BOLT, 1/2-13 x 1 3/ DECK-LIFT HANGER SPANNER RUBBER DECK-LIFT HANGER BUSHING DECK-LIFT LINK BUSHING HEX BOLT 1/2-20 x 1 1/ MACH BUSH, 1/2 ID X 7/8 OD X 14 GA WASHER LOW PROFILE NUT-1/ /8 X 2 1/8 MACHINE BUSHING, 14 GA *NOTE: MODELS PRIOR TO SERIAL MAY REQUIRE CHANGEOVER UPON REPLACEMENT OF DECK-LIFT COMPONENTS. IMPROVED SYSTEM REQUIRES THE FOLLOWING PART REFERENCE NUMBERS AND QUANTITIES. SEE YOUR AUTHORIZED WRIGHT DEALER FOR DETAILS. (QTY) - REF# (4)-22 (2)-48 (1)-32 (1)-49 (1)-33 (2)-50 (2)-34 (2)-51 (4)-35 (2)-52 (4)-42 (2)-53 (4)-43 (4)-54 (1)-44 (4)-55 (1)-45 (4)-56 (1)-47 (4)-57 (1) Wright Manufacturing, Inc. All rights reserved.

15

16 SEAT ASSEMBLY REF. # DESCRIPTION PART # 1 SEAT CUSHION, INCLUDES 2,3,4x4,5x4,6x4,7x SEAT SUPPORT PLATE SEAT GUARD BOLT, HEX 5/16-18 X 1 Z WASHER, LOCK 5/16 Z WASHER, FLAT USS 5/16 z SCREW, PH PAN SMS #8 X 1/2 Z SEAT ADJUSTMENT KNOB MACH BUSH 7/8 X 1 3/8 X 10 GA MEDAL BOLT, HEX 1/2-20 BOLT1/2-20-AXLE 11 SEAT UPPER NUT, NYLOCK JAM 1/2-20 Z MACH BUSH, 7/8 ID X 1 3/8 OD X 14 GA NUT SLEEVE SNAP RING SEAT ADJUSTER ASSEMBLY W/ BUSHINGS PBUSH MEDIUM SEAT ADJUSTMENT ROLLER SEAT UPPER SPRING SUPPORT SPRING, SENTAR SEAT, 7" HBUSH SMALL SEAT UPPER SUPPORT ARM SEAT LOWER SUPPORT ARM SEAT MAIN PIVOT BRACKET GROOVE PIN,.875 X 6.5 Z PIN, SPRING 3/16 X E-CLIP 7/ Wright Manufacturing, Inc. All rights reserved.

17

18 HYDRAULIC PARTS REF. # DESCRIPTION PART # 1 HYDRO OIL TANK PLUG, STEEL 3/ HYDRO MOTOR, 12P O-RING FITTING, 7/8-14 UNF X 1/2 JIC ELBOW, SWIVEL NUT, 1/ ELBOW, STRGHT THRD ORING 1/2 X 5/ FITTING, 3/8 FPIPE X 3/8 MALE JIC FITTING, BARBTITE FEMALE ELBOW HOSE, TANK-FLTR, INCL #8x2, HOSE, HYDRO HIGH PRESS RIGHT HOSE, HYDRO HIGH PRESS LEFT TEE, NYLON HOSEBARB MALE, 3/8" HOSE, FLTR-PUMP, INCL #8x3, # HOSE, PUMP-TANK, INCL #8x2, # ELBOW, STRGHT THRD ORING 3/8 X 3/ HYDRO OIL FILTER HOUSING HYDRO OIL FILTER FITTING, 3/8 MPIPE O-RING X 3/8 MALE JIC HYDRO PUMP, LEFT HYDRO PUMP, RIGHT Wright Manufacturing, Inc. All rights reserved.

19

20 (Qty. 2) 6 7 (Qty. 3) (Qty. 2) 15 16(Qty. 2) (Qty. 2) LG, Sentar Commercial Benefits Left Dash, Cautions All Logos Shield, Missing Right Dash Circle with W Decal, 36 Deck Size Decal, 42 Deck Size Decal, 48 Deck Size Decal, 52 Deck Size Height of Cut Patent Numbers Danger, Blade hazard CE, Parking Brake CE, Danger, Blade Hazard CE, Left Dash, Cautions CE, Noise 100dB CE, Shield Missing CE, Hearing Protection Quad Lever

21

22

23

24 4600X Wedgewood Blvd Frederick, MD