Reproduction. Not for. Parts Manual. S125XT Series Zero-Turn Riding Mowers

Transcription

1 Parts Manual S125XT Series Zero-Turn Riding Mowers Models: Description: S125XTB2552, 52" Mid-Mount Zero-Turn Rider S125XTKAV2352, 52" Mid-Mount Zero-Turn Rider S125XTB2761, 61" Mid-Mount Zero-Turn Rider S125XTKAV2461, Mid-Mount Zero-Turn Rider S125XTB2552 CAL, 52" Mid-Mount Zero-Turn Rider S125XTKAV2352 CAL, 52" Mid-Mount Zero-Turn Rider S125XTB2761 CAL, 61" Mid-Mount Zero-Turn Rider S125XTKAV2461, 52" Mid-Mount Zero-Turn Rider S125XTKAVE2661, 61" Mid-Mount Zero-Turn Rider Briggs and Stratton Products Group, LLC 5375 North Main Street Munnsville, NY USA Manual Part No Revision J Rev. Date: 4/25/2016

2

3 Table Of Contents MODEL COMPONENTS PAGE Main Frame Group... 4 Rear Bumper & ROPS... 6 Seat Mount & Floor Group... 8 Fuel Supply Hose & Tank Replacement Parts Fuel Tank & Mount Group Instrument Control Panel Group Instrument Control Panel Group - Kawasaki Fuel Injected Models Engine & PTO Group Transaxle Drive Group Motion Control Group - Control System Motion Control Group - Handles & Dampeners Hydraulic Group Parking Brake Group Deck Lift Group Transaxle SERVICE PARTS - ZT3400 ( _ ) Wheel & Tire Group Decal Group - Brand & Model Decal Group - Safety & Operation EVAP Canister Group - CAL Models (S/N: All); Other Models (S/N : & Below) EVAP Group - S/N : & Above " & 61" Mower Deck - Hanger Chains " Mower Deck - Rollers " Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Below " Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Above " Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Below " Mower Deck - Rollers " Mower Deck - Housing, Covers, Spindles, & Blades " Mower Deck - Housing, Covers, Spindles, & Blades " Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Above Spindle SERVICE PARTS Electrical Group Electrical Group - Kawasaki Fuel Injected Models Electrical Schematics Electrical Schematics - Kawasaki Fuel Injected Torque Specification Chart... Inside Back Cover

4 Main Frame Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

5 Main Frame Group REF NO PART NO. QTY. DESCRIPTION 1 1 * WELD, MAIN FRAME, S125XT - RED CAP, LOW PROFILE, STEEL SEAL, GREASE BEARING, TAPERED ROLLER, WASHER, 3/4 SAE WASHER, BELLEVILLE X NUT, 3/4-16, HEX JAM NYLON LOCK BOLT, 1/4-28 X 1/2, GD5 YZ D 2 WELD, CASTER YOKE - RED BEARING CUP (SV) Footnotes * If frame is damaged, call ext

6 Rear Bumper & ROPS NOTE: Unless noted otherwise, use the standard hardware torque specification chart

7 Rear Bumper & ROPS REF NO PART NO. QTY. DESCRIPTION A 1 PLATE, HEAT SHIELD, S125XT - BLACK D 1 PLATE, CARB PROTECTOR - RED D 1 WELD, BUMPER, S125XT - RED ROPS (Call x708 if replacing a ROPS) (SEE NOTE ON IMAGE) X10 6 BOLT, 1/2-13 X 1-1/4 GD5 YZ NUT, 1/2-13 HEX NYLOCK FLANGE WASHER, 1/2 SAE WASHER, 5/16 SAE NUT, 5/16-18 HEX NYLOCK FLANGE X6 6 BOLT, 5/16-18 X 3/4 GD SEAT BELT, RETRACTING - ASSM SCREW, 1/2-13 X 1.00, SHCS A 2 BAR, MOUNT, SEAT BELT, S125XT - BLK NUT, 1/2-13 HEX NYLON LOCK X24 4 BOLT, 1/2-13 X 3 GD5 YZ X1 2 ANTI-RATTLE SPRING, FEMCO # (SV) Footnotes

8 Seat Mount & Floor Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

9 Seat Mount & Floor Group REF NO PART NO. QTY. DESCRIPTION MNT, VBRTN, RBBR D 1 PLATE, FLOOR RIGID, S125XT - RED D 1 PLATE, FLOOR, REMOVABLE, S125XT - RED NUT, 5/16-18 HEX NYLOCK FLANGE WASHER, 5/16 SAE X8 2 BOLT, 5/16-18 X 1 GD5 YZ WASHER, 3/8 SAE X44 2 BOLT, 3/8-16 X 5-1/2 GD5 YZ NUT, 3/8-16 HEX NYLOCK FLANGE SEAT, XB-180, NO LOGO, BLACK (S/N: & Below) 10A ARMREST KIT (SV - S/N: & Below) 10B SPRING, EXTENSION, SEAT ADJUSTMENT (BLK OR SLVR) (SV - S/N: & Below) (3-1/2" Total unstretched length) 10C X1 1 SEAT RAIL, KIT, RH AND LH (SV - S/N: & Below) X10 1 BOLT, 5/16-18 X 1-1/4, CARRIAGE YZ NUT, 5/16-18, HEX, CNTR LK, ZC/CL KNOB-INT THR ARM 2.12WD 1.06LG SAFETY WALK, FLOOR REST, 6.00 X SAFETY WALK, FLOOR PLATE, S50X, 10X X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE A 1 PLATE, SEAT BELT GUARD - BLK X8 2 SCREW, 1/4-20 X 1, ALLEN BH, CZ NUT, 1/4-20 HEX NYLOCK FLANGE ASSM, SEAT PLATE W/ DECALS, S125XT (SV)( D) X18 2 BOLT, 5/16-18 X 2-1/4 GD5 YZ D 1 PLATE, SEAT SWITCH, RED SPACER,.33 X.66 X 1.31 SHLDR, CZ SPRING, COM 720ID X 1.31KG X.118WIRE WASHER,.34 X 1.25 X 10 GA SPRING, SEAT SUPPORT SEAT, 907 SEAT INC (S/N: & Above) 27A X1 1 4" SL TRACK SET - 9" FLAT - W/HDWR (SV - S/N: & Above) 27B ARM REST, BLACK MOLDED, PAD ONLY (SV - S/N: & Above) 27C X3 1 BACK ASSEMBLY FOR 907 (SV - S/N: & Above) 27D X4 1 CUSHION ASSEMBLY FOR 907 (SV - S/N: & Above) 27E X5 1 ARM BRACKET W/PAD & HARDWARE (SV - S/N: & Above) 27F X6 1 DELTA SWITCH - NORMALLY CLOSED (SV - S/N: & Above) Footnotes

10 Fuel Supply Hose & Tank Replacement Parts NOTE: Unless noted otherwise, use the standard hardware torque specification chart

11 Fuel Supply Hose & Tank Replacement Parts REF NO PART NO. QTY. DESCRIPTION CLAMP, HOSE EXTERNAL, 1/2 - RED X29 1 HOSE, 1/4" FUEL, 29.00" (Briggs & Stratton Commercial Turf Engines Only) X13 1 WIRE LOOM, 1/2 ID, LONG (Briggs & Stratton Commercial Turf Engines Only) X3 1 FUEL FILTER (SV) HOSE ASSEMBLY (SV) X9 1 HOSE, 1/4" FUEL, 9.00" (Kawasaki Carbureted Engines Only) X6 2 BOLT, 1/4-20 X 3/4 GD5 YZ (Briggs & Stratton Commercial Turf Engines Only) WASHER, 1/4 SAE (Briggs & Stratton Commercial Turf Engines Only) CLAMP, VINYL INSULATED (Briggs & Stratton Commercial Turf Engines Only) NUT, 1/4-20 HEX NYLOCK FLANGE (Briggs & Stratton Commercial Turf Engines Only) X34 1 HOSE, 1/4" FUEL, 34.00" (Kawasaki Fuel Injected Engines Only) Footnotes

12 Fuel Tank & Mount Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

13 Fuel Tank & Mount Group REF NO PART NO. QTY. DESCRIPTION TANK, FENDER, S150X / S200X TANK, FUEL, SNAPPER PRO - LH FUEL CAP, 3-1/2", MANAGED VENT OUT, 12" A 1 MOUNT, TANK REAR, LH - BLK A 1 MOUNT, TANK REAR, RH - BLK X6 12 BOLT, 5/16-18 X 3/4 GD WASHER, 5/16 F436 FLAT WASHER, 5/16 LOCK YZ X8 4 BOLT, 3/8-16 X 1 GD5 YZ WASHER, 3/8 SAE NUT, 3/8-16 HEX NYLOCK FLANGE GAUGE, FUEL, 12 (SV) X1 1 GROMMET, FUEL GAUGE (SV) Footnotes

14 Instrument Control Panel Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

15 Instrument Control Panel Group REF NO PART NO. QTY. DESCRIPTION X4 3 SCREW, ALLEN HEAD 1/4-20X.500 ZINC PHOS RING, SWITCH RETAINER SWITCH, BLADE ENGAGEMENT PLUG,.820X1.44 HOLE, BLACK PLASTIC * HOUR METER, ASSEMBLE ( ) O-RING, 7/8 ID X 1/16 W SWITCH, IGNITION, 6 POST NUT, 3/8-24 HEX X6 2 SCREW, #10-24 X 3/4 ROUND PHILLIPS NUT, #10-24 HEX NYLON LOCK LEVER, THROTTLE CONTROL, HEAVY-DUTY A 1 PLATE, CONTROL PANEL, S125XT - BLACK TIE,SELF-LOCKING, 6" CABLE, CHOKE CONTROL, CABLE, THROTTLE, 42" X1 1 THROTTLE CONTROL HANDLE/KNOB (SV) KEY, IGNITION, SET (SV) COVER (SV) PLASTIC NUT (SV) Footnotes * When replacing this hour meter, please call our service department at

16 Instrument Control Panel Group - Kawasaki Fuel Injected Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart

17 Instrument Control Panel Group - Kawasaki Fuel Injected Models REF NO PART NO. QTY. DESCRIPTION X4 3 SCREW, ALLEN HEAD 1/4-20X.500 ZINC PHOS RING, SWITCH RETAINER SWITCH, BLADE ENGAGEMENT PLUG,.820X1.44 HOLE, BLACK PLASTIC * HOUR METER, ASSEMBLE ( ) O-RING, 7/8 ID X 1/16 W SWITCH, IGNITION, 6 POST KEY, IGNITION, SET (SV) COVER (SV) PLASTIC NUT (SV) TIE,SELF-LOCKING, 6" A 1 PLATE, CONTROL PANEL, S125XT,KAV EFI - BLK ACTUATOR, ROCKER SWITCH, RED BODY, ROCKER SWITCH LIGHT, INDICATOR, PANEL, RED X12 1 BOLT, 1/4-20 X 1-1/2 GD5 CZ WASHER, 1/4 SAE NUT, 1/4-20 HEX NYLOCK FLANGE MODULE, THROTTLE CONTROL (SEE ELECTRICAL GROUP - KAWASAKI FUEL INJECTED MODELS) Footnotes * When replacing this hour meter, please call our service department at

18 Engine & PTO Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

19 Engine & PTO Group REF NO PART NO. QTY. DESCRIPTION 1-1 ENGINE, KAWASAKI, FS730 (23) (Kawasaki FS730 Engines) SPACER, 1.13 X 1.75 X KEY 1/4 SQ X 1 1/2 LONG PULLEY,CRANKSHAFT,1.125ID X 5.5OD A SECT CLUTCH, , WARNER 5A KIT, CLUTCH WIRE REPAIR (SV) BELLEVILLE WASHER X.442 X BOLT, CRANKSHAFT, 7/16-20 X 3, GD X18 1 BOLT, 5/16-18 X 2-1/4 GD5 TFL, CZ WASHER,.34 X 1.25 X 10 GA CLUTCH ANCHOR PAD NUT, 5/16-18 HEX NYLOCK FLANGE (Qty: 8 - Kawasaki Engines S/N: & Below) NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) X8 4 BOLT, 5/16-18 X 1 GD5 YZ WASHER, 5/16 SAE (Qty: 6 - Kawasaki Engines S/N: & Below) A 1 ANCHOR, CLUTCH, S125XT - BLK X14 2 BOLT, 5/16-18 X 1-3/4 GD5 YZ (Kawasaki Engines S/N: & Below) 17A MUFFLER, RIGHT OUTLET ASSY (B&S Commercial Turf Engines) 17B MUFFLER, KAWI, HORIZONTAL, 5" CAN (Kawasaki Engines) BOLT,HEX FLG,SER GD5 3/8-16X1-1/4PACH CZ (Kawasaki Engines Only) GROMMET, 7/ ADAPTER-OIL DRAIN (Kawasaki Engines Only) HOSE, OIL DRAIN TIE,SELF-LOCKING, 24" NO LONGER AVAILABLE - LABEL, BRIGGS & STRATTON LOGO SPACER,.39 X 1.00 X.80, CZ (Kawasaki Engines S/N: & Below) WASHER, 5/16 INT. TOOTH LOCK EXTENSION, TAILPIPE, 3" - BLACK (B&S Engines Only - S/N: & Below) SCREW,SELF-TAP,#8-32 X 3/8, WASH HEX, CZ (B&S Engines Only - S/N: & Below) X6 1 BOLT, 1/4-20 X 3/4 GD5 YZ WASHER, 1/4 SAE CLAMP, VINYL INSULATED NUT, 1/4-20 HEX NYLOCK FLANGE X14 4 BOLT, 5/16-24 X 1-3/4, GD8 (B&S Engines Only) NUT, 5/16-24, NYLOCK FLANGE, GD8, CZ (B&S Engines Only) 34-1 ENGINE, KAWASAKI, FS691 (24) (Kawasaki FS691 Engines) 35-1 ENGINE, BRIGGS & STRATTON, 44T877 (25) (B&S 44T877 Engines) 36-1 ENGINE, BRIGGS & STRATTON, 49T877 (27) (B&S 49T877 Engines) 37-1 ENGINE, KAWASAKI, FS730V, EFI (26) (Kawasaki FS730 EFI Engines) Footnotes

20 Transaxle Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

21 Transaxle Drive Group REF NO PART NO. QTY. DESCRIPTION SHIELD, BEARING PULLEY, 3/8ID, CZ SHIELD, PULLEY BEARING, CZ NUT, 3/8-16 HEX NYLOCK FLANGE WASHER, 1/2 SAE X40 1 BOLT-1/2-13 X 5 GD5 YZ PULLEY, IDLER 5"OD.500ID,.75W STL SPACER,.52 X 1.00 X.22, CZ SPACER, IDLER ARM, 1/2, PM BEARING, BALL, AXLE SPACER,.52 X.84 X 1.53, PM A 1 WELD, IDLER ARM, PUMP DRIVE - BLK NUT, 1/2-13 HEX NYLOCK FLANGE PULLEY, C-SEC, V-IDLER, 6.25"ODX3/8ID SPACER,.39 X 1.00 X.63, CZ WASHER, 3/8 GD.9 FLAT X20 1 BOLT, 3/8-16 X 2-1/2 GD5 YZ NUT, 3/8-16 HEX SERRATED FLANGE BELT, A-SEC, 92.00" EL, ARAMID, WRPD EYE BOLT, 3/8-16 X 8, 3THRD, 1EYE, CZ SPRING-EXT, 1.25OD X 9.3LG X.142WR, BLK (COIL-TO-COIL MEASUREMENT: 5" (12.7 CM) X18 1 BOLT, 3/8-16 X 2-1/4 GD5 CZ WASHER-3/8 FENDER SPACER, SHOULDER Footnotes

22 Motion Control Group - Control System NOTE: Unless noted otherwise, use the standard hardware torque specification chart

23 Motion Control Group - Control System REF NO PART NO. QTY. DESCRIPTION NUT, 5/16-18 HEX NYLOCK FLANGE X20 2 BOLT, 5/16-18 X 2-1/2 GD5 YZ BALL JOINT 5/16-24 RH FEMALE STAMPED STL NUT, 5/16-24 HEX ROD, HYDRO LINKAGE, 7.75, CZ NUT, 5/16-24 HEX, LH NUT, 5/16-24 HEX NYLON LOCK NUT, 3/8-16 HEX NYLOCK FLANGE WASHER, 3/8 GD.9 FLAT SPACER,.39 X.55 X.38, CZ BEARING,.375" ID X.875" OD X.341" THK WASHER-3/8 FENDER X16 2 BOLT, 3/8-16 X 2 GD5 YZ BALL JOIN 5/16-24 LH FEMALE W/STUD, BR X12 2 BOLT, 5/16-18 X 1-1/2 GD5 YZ SPACER,.33 X.63 X 1.25, CZ PIVOT, CONTROL SYSTEM, S125XT WASHER, 5/16 F436 FLAT X10 2 BOLT, 5/16-18 X 1-1/4 GD5 YZ ROD, CONTROL SYSTEM, S125XT, CZ X6 2 BOLT, 7/16-14 X 3/4, GD 5 YZ NUT-HEX FLANGE 7/16-14 TWO-WAY LOCK X8 2 BOLT, 3/8-16 X 1 GD5 YZ SPACER,.33 X.625 X.360, CZ A 2 PLATE, CONTROL MOUNT - BLK Footnotes

24 Motion Control Group - Handles & Dampeners NOTE: Unless noted otherwise, use the standard hardware torque specification chart

25 Motion Control Group - Handles & Dampeners REF NO PART NO. QTY. DESCRIPTION A 1 WELD, HANDLE MOTION CONTROL LH - BLK ROD, NEUTRAL RETURN, CZ FLANGED BUSHING, 3/8IDX.63ODX.8125FL COLLAR, 3/8 SET SPRING, REVERSE RETURN BUSHING, FLANGE 3/8ID X 7/8 LONG A 2 MOUNT, CONTROL ARM - BLK (9.0" Total Length, 4 Adjustment Holes) A 1 WELD, HANDLE MOTION CONTROL RH - BLK A 1 WELD, CONTROL SHAFT, RH - BLK GRIP, FOAM, 3/4 ID, 16 LONG X14 4 BOLT, 3/8-16 X 1-3/4 GD NUT, 3/8-16 HEX NYLON LOCK PIN, HAIR,.0915 X 1-7/ NUT, 1/4-20 HEX NYLOCK FLANGE NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) NUT, 5/16-18 HEX SERRATED FLANGE (SMALL) X12 2 BOLT, 5/16-18 X 1-1/2 GD5 TFL X14 4 BOLT- 5/16-18 X 1-3/4 GD5 TFL A 2 BRACKET, SWITCH MOUNT - BLK A 1 PLATE, NEUTRAL LOCK, LH - BLACK A 1 PLATE, NEUTRAL LOCK, RH - BLACK SEE ELECTRICAL GROUP WASHER, 5/16 SAE X6 6 BOLT, 5/16-18 X 3/4 GD NUT, 5/16-18 HEX NYLOCK FLANGE MM BALL STUD, 5/16-18 X 3/4 THDS DAMPENER, CONTROL,#(P6709/P3610) BEARING, BRONZE FLANGE, 3/ BEARING, FLANGE X10 4 BOLT, 3/8-16 X 1-1/4 GD WASHER, 3/8 SAE X6 4 BOLT, 3/8-16 X 3/4 GD5 YZ NUT, 3/8-16 HEX NYLOCK FLANGE A 1 WELD, CONTROL SHAFT, LH - BLK SCREW, 5/16-18X0.750, GR5, WHIZ-LOCK, ZC BOLT,1/4-20X0.750,GR5,RH SQ NK,ZNC/CLR Footnotes

26 Hydraulic Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

27 Hydraulic Group REF NO PART NO. QTY. DESCRIPTION TRANS, LH, ZS-KHEF-8T7C-11RX TRANS, RH, ZS-GHEF-8T7B-11 RX HYDRO RES. #71328, 350 ml FITTING, 9/16 O-RING-1/2" HOSE, 90 DEG CLAMP, HOSE,.75 FREE DIA ROD, DUMP VALVE, S125XT, CZ X6P5 2 HOSE, 1/2" PUSH-ON, 6.50" CLIP, RETAINER, BRAKE ARM, ZT BRAKE ARM, ZT X24 4 BOLT, 5/16-18 X 3 GD5 YZ X20 4 BOLT, 5/16-18 X 2-1/2 GD5 YZ (S/N: & Below) X20 4 BOLT, 3/8-16 X 2-1/2 GD5 (S/N: & Above) NUT, 5/16-18 HEX NYLOCK FLANGE (QTY: 12 - S/N: & Below) NUT, 3/8-16 HEX NYLOCK FLANGE (S/N: & Above) NUT, 1/4-20 HEX SERR. FLANGE X6 8 BOLT, 1/4-20 X 3/4 GD5 YZ WASHER, 1/4 SAE NUT, 1/4-20 HEX NYLOCK FLANGE WASHER, 1/4 FENDER PIN, HAIR,.0585 X 1-1/8, 1/4 EYE, YZ X1 2 RESERVOIR CAP (SV) A 2 PLATE, HYDRO BOTTLE MOUNT - BLACK WASHER, 3/8 SAE (S/N: & Above) WASHER, 5/16 F436 FLAT (QTY: 8 - S/N: & Below) Footnotes

28 Parking Brake Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

29 Parking Brake Group REF NO PART NO. QTY. DESCRIPTION A 1 WELD, BRAKE SHAFT, S125XT - BLK A 2 LINK, BRAKE LOCK, S125XT - BLK A 2 LINK, LOWER BRAKE, S125XT - BLK SPACER,.33 X.50 X.25, CZ BEARING, 1/2 FLANGED, PLASTIC BALL SPACER,.32 X.50 X.83, CZ SPACER,.38 X.50 X.27, CZ GRIP, FOAM,.475 X 4.35 X SPRING-COMP,.496ID X 3.00LG X.112WR (Coil-to-coil compressed spring length: 2-3/4" (7 cm)) NUT, 3/8-16 HEX SERRATED FLANGE SPRING-COMP,.600ID X 5.50LG X.080WR X12 2 BOLT, 3/8-16 X 1-1/2, FLANGE, GD 5, CZ NUT, 3/8-16 HEX NYLOCK FLANGE X5 4 BOLT-1/4-20 X 5/8 GD5 YZ NUT, 1/4-20 HEX NYLOCK FLANGE NUT, 5/16-18 HEX SERRATED FLANGE (SMALL) X10 1 BOLT, 5/16-18 X 1-1/4 GD5 YZ WASHER, 5/16 SAE NUT, 5/16-18 HEX NYLOCK FLANGE X14 2 BOLT, 5/16-18 X 1-3/4 GD5 YZ X9 2 BOLT, 5/16-18 X 1-1/8 GD CABLE, PARKING BRAKE, 31" (787.9 MM) NUT, 5/16-18 HEX NUT, 5/16-24 HEX NYLON LOCK SEE ELECTRICAL GROUP TIE, SELF-LOCKING, 12" Footnotes

30 Deck Lift Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

31 Deck Lift Group REF NO PART NO. QTY. DESCRIPTION X22 1 BOLT, 1/2-13 X 2-3/4 GD5 YZ X16 1 BOLT, 1/2-13 X 2 GD5 YZ (Qty: 2-61" decks) WASHER, 1/2 SAE (Qty: 16-61" decks) NUT, 1/2-13 HEX NYLOCK FLANGE (Qty: 5-61" decks) NUT, 1/2-13 HEX JAM (Qty: 2-61" decks) X14 4 BOLT, 1/2-20 X 1-3/4 GD8 YZ X10 2 BOLT, 3/8-16 X 1-1/4 GD NUT, 3/8-16 HEX NYLOCK FLANGE (Qty: 8-61" decks) A 1 PEDAL, FOOT - BLK WASHER, 3/8 SAE NUT, 3/8-16 HEX SERRATED FLANGE (Qty: 2-61" decks) X22 4 BOLT, 3/8-16 X 2-3/4 GD5 YZ WASHER, 1/4 FENDER NUT, 1/4-20 HEX NYLOCK FLANGE X5 2 BOLT-1/4-20 X 5/8 GD5 YZ BOLT, 3/8-16 X 3/4, PLT W/PATCH WASHER,.390 X 1.50 X.109, YZ SPACER,.52 X 1.00 X.88, CZ INSERT, BEARING SPRING-EXT, 1.00 ODX13.25LGX.177WR, BLK (Qty: 2-61" decks) PIN, HITCH, 1/2 X 2.00 OAL, YP X4 1 PIN, CLEVIS, 1/4 X 1/2, PLATED JOINT-BALL THD.500ID, CLR ZINC ROD, DECK LIFT SNP SPRING-EXT,.740 ODX2.025LGX.072WR, BLK EYE BOLT, 3/8-16 X 6, 3THRD, 1EYE, CZ (52" Decks S/N: & EYE BOLT, 3/8-16 X 4, 2.13THRD, 1 EYE,CZ (52" Decks S/N: & Above) EYE BOLT, 3/8-16 X 6, 3THRD, 1EYE, CZ (61" Decks S/N: & EYE BOLT, 3/8-16 X 4, 2.13THRD, 1 EYE,CZ (61" Decks S/N: & Above) GRIP, FOAM,.475 X 4.35 X COLLAR, 5/8 SPLIT GREASE FITTING, 1/4-28 STRAIGHT BUSHING, 1.00 X 1.13 X 1.38, PLASTIC RUBBER, FOOT PEDAL PIVOT BLOCK, PLASTIC A 1 WELD, PULLER BAR, S125XT - BLACK D 1 WELD, DECK LIFT SHAFT, S125XT - RED (S/N: & Below) D 1 WELD, DECK LIFT SHAFT - RED (S/N: & Above) A 1 WELD, ROD DECK LIFT, S125XT - BLK A 1 PIVOT, DECK LIFT WELD - RIGHT - BLK A 1 PIVOT, DECK LIFT WELD - LEFT - BLK Footnotes

32 Deck Lift Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

33 Deck Lift Group REF NO PART NO. QTY. DESCRIPTION A 2 PLATE, PIVOT BLOCK SUPPORT - BLK A 1 WELD, DECK HEIGHT LINK - BLACK NUT, 1/2-20 HEX NYLON LOCK NUT, 1/2-20 HEX JAM X14 2 BOLT, 1/2-13 X 1-3/4 GD5 YZ Footnotes

34 Transaxle SERVICE PARTS - ZT3400 ( _ ) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

35 Transaxle SERVICE PARTS - ZT3400 ( _ ) REF NO PART NO. QTY. DESCRIPTION X3 - KIT, FAN & PULLEY - HG# X5 - FAN, HG# X6 - KIT, PULLEY HG# X4 - KIT, INPUT SHAFT (BEARING AND SHAFT ONLY) HG# X2 - KIT, SEAL - HG# X1 - KIT, SEAL, AXLE HG# X1 - FILTER, OIL, HG# X5 - BEARING, 6205M, HG# X12 - KIT, CHARGE PUMP, HG# X2 - SEAL, CONTROL ARM, 18X32X7, HG# X3 - OUTPUT SHAFT SEAL, 17X40X7 HG# X4 - RING, RET 2.06 INT, HG# X8 - ASSM, HUB HG# X7 - AXLE CAP, HG# Footnotes (All part identified with ref # 5 are included in the Seal Kit.)

36 Wheel & Tire Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

37 Wheel & Tire Group REF NO PART NO. QTY. DESCRIPTION S 2 TIRE, CASTER, 13 X A X1 2 TIRE ONLY (SV) 1B SX1 2 WHEEL ASSY, 13 X 5 X 6, SILVER (SV) 1C SX2 4 BEARING, TAPERED CONE (SV)(Qty: 2 per tire) 1D SX3 4 SEAL, GREASE (SV)(Qty: 2 per tire) ADAPTER, CASTER AXLE, CZ (SV)(Qty: 2 per tire) WASHER, 1/2 SAE X64 2 BOLT, 1/2-13 X 8 GD5 YZ NUT, 1/2-13 HEX NYLOCK FLANGE NUT, 1/2-20, FOR WHEEL BOLT SILVER (Torque Lug Nut to 90 ft.lbs (122 Nm)) TIRE/WHEEL ASM, 22X11-10,TM,.781 OFFSET (Models with 52" mower decks) TIRE/WHEEL ASM, 22X11-10, TURF MASTER (Models with 61" mower decks) 7A X1 2 WHEEL, 10 X 7,.781 POS OFFSET, 4 ON 4 (SV) 8A X1 2 WHEEL, 10 X 7 4/4, 0" OFFSET (SV) X2 2 TIRE, 22 X , 4 PLY (SV) Footnotes

38 Decal Group - Brand & Model NOTE: Unless noted otherwise, use the standard hardware torque specification chart

39 Decal Group - Brand & Model REF NO PART NO. QTY. DESCRIPTION DECAL, SNAPPER PRO LOGO, SMALL DECAL, SNAPPER PRO, S125XT DECAL, icd CUTTING SYSTEM DECAL, 52 (52" Models Only) DECAL, 61 (61" Models Only) Footnotes

40 Decal Group - Safety & Operation NOTE: Unless noted otherwise, use the standard hardware torque specification chart

41 Decal Group - Safety & Operation REF NO PART NO. QTY. DESCRIPTION DECAL, MAIN SAFETY DECAL, WARNING, HAND IN BELT, ENG ONLY DECAL, DANGER DO NOT OPERATE W/O DEFLECT DECAL, TRANSAXLE RELEASE, S125XT DECAL, WARNING, ROLL BAR DECAL, IGNITION SWITCH DECAL, THROTTLE CONTROL 8-1 ORDER PART NUMBERS & (SV) DECAL, WARNING OVERHANG, ROPS (SV) DECAL, HYDRAULIC OIL, SAE 20W DECAL, CUT HEIGHT, S125XT DECAL, BELT & BLADE, S125XT DECAL, PINCH POINT (Qty: 1 for models with 52" mower deck) DECAL, MANUAL AVAIL IN SPANISH DECAL, FUSE LOCATION, KAWI EFI (Kawasaki Fuel Injected Models Only) Footnotes

42 EVAP Canister Group - CAL Models (S/N: All); Other Models (S/N : & Below) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

43 EVAP Canister Group - CAL Models (S/N: All); Other Models (S/N : & Below) REF NO PART NO. QTY. DESCRIPTION CNSTR, CARB, 6 GAL CLAMP, 3" ID, CUSHIONED, STAINLESS X6 2 SCREW,1/4-20X3/4, ZINC PHOS & OIL NUT, 1/4-20 HEX NYLOCK FLANGE X38 1 HOSE, VAPOR, 5MM ID, LG (Briggs & Stratton Models) X6 1 HOSE, VAPOR, 5MM ID, 6.00 LG TIE, SELF-LOCKING, 12" HOSE, FORMED, EVAP CANISTER FITTING, STRAIGHT, 10MMX10MM, PLASTIC CLAMP, HOSE FITTING, 90 DEG, 3/16X3/16, SANTOPRENE FITTING, STRAIGHT, 3/16X3/16, PLASTIC X8 2 BOLT, 1/4-20 X 1, GD WASHER, 1/4 SAE A 1 MOUNT, EPA CANISTER, S125XT - BLK X27 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Models) DUST FILTER, CANISTER (SV) ASSEMBLY, REMOTE VENT, NO VALVE (SV) GROMMET (SV) Footnotes

44 EVAP Group - S/N : & Above NOTE: Unless noted otherwise, use the standard hardware torque specification chart

45 EVAP Group - S/N : & Above REF NO PART NO. QTY. DESCRIPTION FITTING, 3/16" TEE, BARB TYPE, HDPE X33 1 HOSE, VAPOR, 5MM ID, LG (Briggs & Stratton Engines Only) X10 1 HOSE, VAPOR, 5MM ID, LG (Briggs & Stratton Engines Only) X2 1 HOSE, VAPOR, 5MM ID, 2.00 LG (Briggs & Stratton & Kawasaki EFI Engines) TIE,SELF-LOCKING, 6" (Qty: 5 on models equipped with Kawasaki Carbureted Engines) FILTER, FUEL X15 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Carbureted Engines Only) X18 2 HOSE, VAPOR, 5MM ID, LG (Kawasaki Carbureted Engines Only) X34 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki EFI Engines) X16 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki EFI Engines) Footnotes

46 52" & 61" Mower Deck - Hanger Chains NOTE: Unless noted otherwise, use the standard hardware torque specification chart

47 52" & 61" Mower Deck - Hanger Chains REF NO PART NO. QTY. DESCRIPTION NUT, 3/8-16 HEX NYLOCK FLANGE X14 6 BOLT, 3/8-16 X 1-3/4 GD WASHER, 3/8 SAE NUT, 3/8-16 HEX SERRATED FLANGE NUT, 3/8-16 HEX JAM X3 2 CHAIN, 5/16 GD30, 3 LINKS X2 2 CHAIN, 5/16 GD30, 2 LINKS CLEVIS, 5/16-18, 3/8 PIN HOLE, CLR ZINC X6 2 PIN, COTTER, 3/32 X 3/ X9 2 PIN, CLEVIS, 3/8 X 1-1/8, CZ X16 2 BOLT, 5/16-18 X 2 GD5 TFL NUT, 5/16-18 HEX X16 2 BOLT, 3/8-16 X 2 GD5 YZ Footnotes

48 61" Mower Deck - Rollers NOTE: Unless noted otherwise, use the standard hardware torque specification chart

49 61" Mower Deck - Rollers REF NO PART NO. QTY. DESCRIPTION NUT, 3/8-16 HEX NYLOCK FLANGE X28 2 BOLT, 3/8-16 X 3-1/2 GD5 CZ SPACER,.38 X.50 X SPACER,.51 X.75 X.56, CZ WHEEL WIDE 3.88 DIA 0.531ID POLY WASHER, 1/2 GD9 YZ SPACER,.38 X.50 X X48 1 BOLT, 3/8-16 X 6 GD5 YZ (For Anti-Scalp brackets with round holes.) WASHER, 3/8 SAE NUT, 3/8-16 HEX SIDE LOCK X48 1 BOLT, CARRIAGE, 3/8-16 X 6, GD5, CZ (For Anti-Scalp brackets with square holes.) Footnotes

50 52" Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart

51 52" Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Below REF NO PART NO. QTY. DESCRIPTION NUT, 3/8-16 HEX SERRATED FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE EYE BOLT, 3/8-16 X 6, 3.0 THREAD GREASE FITTING, 1/4-28 STRAIGHT NUT, 1/2-13 HEX NYLOCK FLANGE WASHER, 1/2 USS *PULLEY, FLAT IDLER, 6-3/4" *If not present, order washer and shield SHIELD, PULLEY BEARING NUT, 3/4-16 HEX WASHER, 3/4 BELLEVILLE X10 3 KEY, 1/4 SQ X 1-1/ PULLEY, OVER BALL BUSHING, FLANGE SPACER,.52 X 1.00 X X36 1 BOLT, 1/2-13 X 4-1/2 GD5 YZ PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID A 1 WELD, IDLER ARM - 52" - BLK X20 2 BOLT, 1/2-13 X 2-1/2 GD5 YZ SPACER,.52 X 1.25 X.70, CZ BELT, 5V SEC, 162.4" EL, ARAMID, WRPD, RC X22 1 BOLT, 1/2-13 X 2-3/4 GD5 YZ SPACER,.52 X 1.00 X.56, CZ SPACER,.52 X 1.00 X.22, CZ SPRING, EXTENSION, SWIVEL. LONG HOOK (coil-to-coil measurement: 6-5/8") WASHER, 1/2 SAE Footnotes

52 52" Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Above NOTE: Unless noted otherwise, use the standard hardware torque specification chart

53 52" Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Above REF NO PART NO. QTY. DESCRIPTION A 1 WELD, IDLER ARM - BLK BEARING, /2", SEALED SPACER,.51 X.75 X 1.22, PM, CZ SPACER, IDLER ARM, 1/2 X PULLEY, FLAT IDLER, 6-3/4" PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID SHIELD, PULLEY BEARING, CZ PULLEY, OVER BALL SPACER,.39 X 1.00 X SPACER,.39 X.75 X X44 1 BOLT, 1/2-13 X 5-1/2 GD5 CZ X20 2 BOLT, 1/2-13 X 2-1/2 GD5 CZ SPACER,.52 X 1.00 X.56, CZ SPACER,.52 X 1.25 X.70, CZ NUT, 3/8-16 HEX SERRATED FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE X12 1 BOLT, 3/8-16 X 1-1/2 GD5 CZ WASHER, 1/2 SAE WASHER-3/8 FENDER NUT, 1/2-13 HEX NYLOCK FLANGE X10 3 KEY, 1/4 SQ X 1-1/ WASHER, 3/4 BELLEVILLE NUT, 3/4-16 HEX SPRING, EXT, 1.5ODX12.25X.234WIRE BLK EYE BOLT, 3/8-16 X 5, 2.88THRD, 1EYE, CZ BELT, 5V, "EL, ARAMID WRPD, RC Footnotes

54 61" Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart

55 61" Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Below REF NO PART NO. QTY. DESCRIPTION SPRING, EXTENSION, SWIVEL. LONG HOOK (coil-to-coil measurement: 6-1/8") NUT, 3/8-16 HEX SERRATED FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE EYE BOLT, 3/8-16 X 6, 3 THRD, 1 EYE, CZ (S/N: & Above) EYE BOLT, 3/8-16 X 8, 1 EYE (S/N: & Below) GREASE FITTING, 1/4-28 STRAIGHT X24 3 BOLT, 1/2-13 X 3 GD5 YZ X22 1 BOLT, 1/2-13 X 2-3/4 GD5 YZ WASHER, 1/2 GD9 YZ NUT, 1/2-13 HEX NYLOCK FLANGE WASHER, 1/2 USS SPACER,.52 X 1.00 X.56, CZ SPACER,.52 X 1.00 X.22, CZ *PULLEY, FLAT IDLER, 6-3/4" *If not present, order washer and shield SHIELD, PULLEY BEARING IDLER MOUNT NUT, 3/4-16 HEX WASHER, 3/4 BELLEVILLE X10 3 KEY, 1/4 SQ X 1-1/ PULLEY, 6.93 EOD X 25MM, SPLIT BUSHING, FLANGE SPACER,.52 X 1.00 X X40 1 BOLT-1/2-13 X 5 GD5 YZ A 1 WELD, IDLER ARM - 52" - BLK BELT, 5V, EL, LG ARAMID, WRPD, RC PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID WASHER, 1/2 SAE Footnotes

56 52" Mower Deck - Rollers NOTE: Unless noted otherwise, use the standard hardware torque specification chart

57 52" Mower Deck - Rollers REF NO PART NO. QTY. DESCRIPTION WHEEL WIDE 3.88 DIA 0.531ID POLY BOLT-WHEEL 3/8-16X THRD WASHER-0500(0.51IDX0.87ODX.06THK) BLK NUT, 3/8-16 HEX SIDE LOCK Footnotes

58 52" Mower Deck - Housing, Covers, Spindles, & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart

59 52" Mower Deck - Housing, Covers, Spindles, & Blades REF NO PART NO. QTY. DESCRIPTION DECK SHELL W/ DECALS, 52, S125XT (SV) ( D)(S/N: & Below) DECK SHELL W/ DECALS, S125XT-52, DOM ( D)(S/N: & Above) WASHER, 5/16 SAE X8 12 BOLT, 5/16-18 X 1 GD5 YZ (Torque to 17 ft.lbs (23 Nm)) BODY CLIP, 5/ GA MATERIAL D 1 GUARD, 52 DECK, RH - RED D 1 GUARD, 52 DECK, LH - RED NUT, 5/16-18 HEX NYLOCK FLANGE /16 PUSH-ON NUT RETAINER, STL, CZ A 1 PLATE, SUPPORT - BLK FLAP, STRIPER, 52 DECK X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE A 1 PLATE, DEFLECTOR, 52 DECK - BLK A 1 WELD, FRAME CHUTE, 52 - BLK (S/N: & Below) CHUTE,DISCHARGE,RUBBER HOLE,BENT (S/N: & Below) A 1 SUPPORT, DISCHARGE CHUTE, 52 - BLK (S/N: & Below) NUT, 3/8-16 HEX NYLOCK FLANGE X12 3 BOLT, 3/8-16 X 1-1/2 GD5 YZ (S/N: & Below) SCREW, 5/16-18X0.750, GR5, WHIZ-LOCK, ZC NUT, 5/16-24 HEX NYLON LOCK ROD, MOUNT, CHUTE 61, CZ S 3 BLADE, 18 X.25 X 2.5, 1 X 3.5 (SET OF 3) ASSM, SPINDLE, LOW PROFILE (Nut and Washer Sold Seperately) WASHER, 5/8 GRADE 8, YZ X14 3 BOLT, 5/8-11 X 1-3/4 GD8 (Torque to 70 ft.lbs (94 Nm)) BOLT, 5/16-18 X 1 1/4 FLANGE SAFETY WALK, 4.00 X A 1 WELD, MOUNT, DISCHARGE CHUTE - BLK (S/N: & Above) A 1 SUPPORT, DISCHARGE CHUTE - BLK (S/N: & Above) CHUTE, RUBBER DISCHARGE ( ) (S/N: & Above) X12 3 BOLT, 3/8-16 X 1-1/2, CARRIAGE, GD5, CZ (S/N: & Above) Footnotes

60 61" Mower Deck - Housing, Covers, Spindles, & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart

61 61" Mower Deck - Housing, Covers, Spindles, & Blades REF NO PART NO. QTY. DESCRIPTION DECK SHELL W/ DECALS, 61, S125XT ( D)(S/N: & Below) DECK SHELL W/ DECALS, S125XT-61, DOM ( D)(S/N: & Above) WASHER, 5/16 SAE X8 12 BOLT, 5/16-18 X 1 GD5 YZ (Torque to 17 ft.lbs (23 Nm)) BODY CLIP, 5/ GA MATERIAL D 1 PLATE, GUARD, 61, LH - RED D 1 PLATE, GUARD, 61, RH - RED NUT, 5/16-18 HEX NYLOCK FLANGE /16 PUSH-ON NUT RETAINER, STL, CZ WASHER, 5/16 SAE A 1 PLATE, SUPPORT - BLK FLAP, STRIPER, 61 DECK X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE A 1 PLATE, DEFLECTOR - BLK A 1 WELD, FRAME, CHUTE, 61 - BLK (S/N: & Below) CHUTE, DISCHARGE, BEND RUBBER (SV) (S/N: & Below) A 1 SUPPORT, DISCHARGE CHUTE, 61/72 - BLK (S/N: & Below) NUT, 3/8-16 HEX NYLOCK FLANGE X12 3 BOLT, 3/8-16 X 1-1/2 GD5 YZ (S/N: & Below) SCREW, 5/16-18X0.750, GR5, WHIZ-LOCK, ZC NUT, 5/16-24 HEX NYLON LOCK ROD, MOUNT, CHUTE 61, CZ S 3 BLADE, 21 X.25 X 2.5, 1 X 3.5 (SET OF 3) ASSM, SPINDLE, LOW PROFILE (Nut and Washer Sold Seperately) WASHER, 5/8 GRADE 8, YZ X14 3 BOLT, 5/8-11 X 1-3/4 GD8 (Torque to 70 ft.lbs (94 Nm)) BOLT, 5/16-18 X 1 1/4 FLANGE SAFETY WALK, 4.00 X A 1 WELD, MOUNT, DISCHARGE CHUTE - BLK (S/N: & Above) A 1 SUPPORT, DISCHARGE CHUTE - BLK (S/N: & Above) CHUTE, RUBBER DISCHARGE ( ) (S/N: & Above) X12 3 BOLT, 3/8-16 X 1-1/2, CARRIAGE, GD5, CZ (S/N: & Above) Footnotes

62 61" Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Above NOTE: Unless noted otherwise, use the standard hardware torque specification chart

63 61" Mower Deck - Pulleys, Belt, & Idler Arm - S/N: & Above REF NO PART NO. QTY. DESCRIPTION A 1 WELD, IDLER ARM - BLK X10 3 KEY, 1/4 SQ X 1-1/ X44 1 BOLT, 1/2-13 X 5-1/2 GD5 CZ X24 2 BOLT, 1/2-13 X 3 GD5 CZ X20 1 BOLT, 1/2-13 X 2-1/2 GD5 CZ X12 1 BOLT, 3/8-16 X 1-1/2 GD5 CZ BEARING, /2", SEALED SPACER, IDLER ARM, 1/2 X SPACER,.51 X.75 X 1.22, PM, CZ IDLER MOUNT,.88 HIGH SPRING, EXT, 1.5ODX12.25X.234WIRE BLK BELT, 5V, "EL, LG ARAMID WRPD, RC PULLEY, FLAT IDLER, 6-3/4" IDLER MOUNT PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID SPACER,.52 X 1.00 X.56, CZ SHIELD, PULLEY BEARING, CZ PULLEY, 6.93 EOD X 25MM, SPLIT SPACER,.39 X 1.00 X SPACER,.39 X.75 X WASHER-3/8 FENDER WASHER, 3/4 BELLEVILLE NUT, 3/4-16 HEX NUT, 1/2-13 HEX NYLOCK FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE NUT, 3/8-16 HEX SERRATED FLANGE EYE BOLT, 3/8-16 X 6, 3THRD, 1EYE, CZ Footnotes

64 Spindle SERVICE PARTS NOTE: Unless noted otherwise, use the standard hardware torque specification chart

65 Spindle SERVICE PARTS REF NO PART NO. QTY. DESCRIPTION ASSM, SPINDLE, LOW PROFILE GREASE FITTING (SV) TRASH SHIELD (SV) BEARING (SV) RELIEF VALVE (SV) SPINDLE HOUSING (SV) SPACER, 1.00 X 1.25 X 1.75 (SV) SPINDLE SHAFT (SV) Footnotes

66 Electrical Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

67 Electrical Group REF NO PART NO. QTY. DESCRIPTION WIRE HARNESS, C TURF,WARNER, S125XT (B&S Commercial Turf Engines S/N: All; Kawasaki Engines S/N: & Above) 2-1 USE & (Kawasaki Engines S/N: & Below) 3-1 BATTERY, WET ( BCIU1, 340 CCA) BATTERY CABLE, NEGATIVE, 14" BATTERY CABLE, POSITIVE, STRAP-BLACK RUBB SOLENOID-4 POLE 12 VOLT DC (TROMBETTA) WASHER, 5/16 LIGHT LOCK NUT, 5/16-24 JAM X6 4 BOLT, 1/4-20 X 3/4 GD5 YZ WASHER, 1/4 SAE NUT, 1/4-20 HEX SERR. FLANGE (Qty: 1 used to attach positive battery cable to engine starter - B&S Engine Only) BATTERY CABLE, POSITIVE, BREAKER-CIRCUIT 12VOLT 20AMPS W/TAB CLAMP, VINYL INSULATED FUSE, ATO 15 AMP (SV) GROMMET, 1-1/2" ID FOR 1/4" METAL X18 2 WIRE LOOM, 3/8 ID X 18 IN FIR TREE MOUNT, PACKARD SEAT SWITCH, MILSCO, BOLT-IN (SV) SEAT SWITCH, MILSCO, TWIST-IN (SV) X6 2 SCREW, 1/4-20 X 3/4, ALLEN BH, CZ TIE, SELF-LOCKING, 12" BOLT, M X 2.MM GD 8.8 (Kawasaki Engine Only - Bolt Negative Battery Cable to Engine) NUT, HEX, M8-1.25, YZ, GD 8.8 (Kawasaki Engine Only - Attaches positive battery cable to engine starter) SWITCH, DP NO/NC SNAP-IN NUT, 1/4-20 HEX NYLOCK FLANGE WIRE HARNESS, JUMPER, KAWI (Kawasaki Engines S/N: & Above) Footnotes

68 Electrical Group - Kawasaki Fuel Injected Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart

69 Electrical Group - Kawasaki Fuel Injected Models REF NO PART NO. QTY. DESCRIPTION WIRE HARNESS, IS700, KAWI FS730V EFI MODULE, THROTTLE CONTROL, KAV DFI BATTERY, WET ( BCIU1, 350 CCA) BATTERY CABLE, NEG, 14, 5/16-13/ BATTERY CABLE, POS, 22, 1/4-5/ STRAP-BLACK RUBB SOLENOID-4 POLE 12 VOLT DC (TROMBETTA) WASHER, 5/16 LIGHT LOCK NUT, 5/16-24 JAM X6 5 BOLT, 1/4-20 X 3/4 GD5 CZ WASHER, 1/4 SAE NUT, 1/4-20 HEX SERR. FLANGE BATTERY CABLE, POS, 22, 1/4-5/ COVER, VINYL, FUSE BLOCK CLAMP, VINYL INSULATED, SWITCH, DP NO/NC SNAP-IN GROMMET, 1-1/2" ID FOR 1/4" METAL X18 2 WIRE LOOM, 3/8 ID X 18 IN RELAY, 12V, 40A NUT, 1/4-20 HEX NYLOCK FLANGE X6 1 DELTA SWITCH - NORMALLY CLOSED (SV) X6 4 SCREW, #10-24 X 3/4 ROUND PHILLIPS NUT, #10-24 HEX NYLON LOCK X6 2 SCREW,1/4-20X3/4, ZINC PHOS & OIL TIE, SELF-LOCKING, 12" FUSE, ATO, 30 AMP FUSE, ATO, 40A FUSE, ATO-15 (15 AMP) FUSE, 2 AMP, 32 VOLT, ATO-2 Footnotes

70 Electrical Schematic - Charging Circuit Y:\Catalog_Data\SPR\Images\ \ C S S S S S S S S1 Copyright #Name Briggs and Stratton. All Rights Reserved. 70

71 Electrical Schematic - Cranking Circuit Y:\Catalog_Data\SPR\Images\ \ R S S S S S S S S1 Copyright #Name Briggs and Stratton. All Rights Reserved. 71

72 Electrical Schematic - PTO Clutch Circuit Y:\Catalog_Data\SPR\Images\ \ P S S S S S S S S1 Copyright #Name Briggs and Stratton. All Rights Reserved. 72

73 Electrical Schematic - Ign. Ground Circuit / Op. Pres. Y:\Catalog_Data\SPR\Images\ \ I S S S S S S S S1 Copyright #Name Briggs and Stratton. All Rights Reserved. 73

74 Electrical Schematic - Charging Circuit - Kawasaki Fuel Injected C S1 Copyright #Name Briggs and Stratton. All Rights Reserved. 74

75 Electrical Schematic - Cranking Circuit - Kawasaki Fuel Injected R S1 Copyright #Name Briggs and Stratton. All Rights Reserved. 75

76 Electrical Schematic - PTO Clutch Circuit - Kawasaki Fuel Injected P S1 Copyright #Name Briggs and Stratton. All Rights Reserved. 76

77 Electrical Schematic - Ign. Ground Circuit / Op. Pres. - Kawasaki Fuel Injected I S1 Copyright #Name Briggs and Stratton. All Rights Reserved. 77

78

79 Hardware Identification & Torque Specifications Common Hardware Types Hex Head Capscrew Washer Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Carriage Bolt Lockwasher Hex Nut Standard Hardware Sizing When a washer or nut is identified as 1/2, this is the Nominal size, meaning the inside diameter is 1/2 inch; if a second number is present it represent the threads per inch When bolt or capscrew is identified as 1/2-16 x 2, this means the Nominal size, or body diameter is 1/2 inch; the second number represents the threads per inch (16 in this example, and the final number is the body length of the bolt or screw (in this example 2 inches long). The guides and ruler furnished below are designed to help you select the appropriate hardware and tools. 0 1/4 1/2 3/4 1 1/4 1/2 3/4 2 1/4 1/2 3/4 3 1/4 1/2 3/4 Screw, 1/2 x 2 Body Diameter Body Length Nut, 1/2 Inside Diameter Hardware Grade No Marks SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm / / / / / / / / / / / / / / / / / / , ,000 1,360.0 NOTES 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. for prevailing torque locknuts - use 65% of grade 5 torques. b. for flange whizlock nuts and screws - use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings, all torque values must meet this specification. 4 Wrench & Fastener Size Guide 1/4 5/16 3/8 7/16 DIA. 1/2 DIA. 1/4 Bolt or Nut Wrench 7/16 5/16 Bolt or Nut Wrench 1/2 3/8 Bolt or Nut Wrench 9/16 7/16 Bolt or Nut Wrench (Bolt) 5/8 Wrench (Nut) 11/16 1/2 Bolt or Nut Wrench 3/4

80 Parts Manual S125XT Series Zero-Turn Riding Mowers IT IS THE POLICY OF BRIGGS STRATTON TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED Briggs and Stratton Products Group, LLC North Main Street Munnsville, NY USA Copyright 2016 Briggs and Stratton Corporation All Rights Reserved. Printed In USA.