Reproduction. Not for. Parts Manual. S200XT Series Zero-Turn Riding Mower

Transcription

1 Parts Manual S200XT Series Zero-Turn Riding Mower Models: Description: S200XTBV32, Zero-Turn Rider S200XT - 72" Mower Deck S200XTB3061, 61" Zero-Turn Rider S200XTB30, Zero-Turn Rider S200XTBV36, Zero-Turn Ridier S200XTBV3661, Zero-Turn Rider S/N: & Below S200XTBV2861, 61" Zero-Turn Rider S/N: & Below S200XTKAV2661, 61" Zero-Turn Rider S/N: & Below S200XTB2861, 61" Zero-Turn Rider S/N: & Below S200XTKOH2961, 61" Zero-Turn Rider S/N: & Below S200XTB2761, 61" Zero-Turn Rider S/N: & Below S200XTBV3272, 72" Zero-Turn Rider S200XTBV3672, 72" Zero-Turn Rider S/N: & Below S200XTBV3261 ANSI EXP, 61" Zero-Turn Rider Briggs and Stratton Products Group, LLC 5375 North Main Street Munnsville, NY USA Manual Part No Revision R Rev. Date: 2/3/2015

2

3 Table Of Contents MODEL COMPONENTS PAGE Main Frame Group... 4 Rear Bumper & ROPS Group... 6 Seat Plate & Floor Group (S/N: & Below)... 8 Seat Plate & Floor Group (S/N: & Above) Fuel Tank & Mount Group Fuel Supply Hose & Tank Replacement Parts Group Instrument Control Panel Group Instrument Control Panel Group - EFI Models Engine & PTO Group - Briggs & Stratton - Vanguard Engine & PTO Group - Kawasaki Engine & PTO Group - Briggs & Stratton - Commercial Turf Engine & PTO Group - Kohler EFI Engine Service Parts - Briggs & Stratton Commercial Turf Engine Service Parts - Briggs & Stratton Vanguard Big Block Engine Service Parts - Kawasaki (FX651V - FX1000V) Engine Service Parts - Kohler ECV749 EFI Transaxle Drive Group Motion Control Group Hydraulic Group S/N: & Below Parking Brake Group Deck Lift Group - 61" Models Deck Lift Group - 72" Models S/N: & Below Deck Lift Group - Spring Assist - 72" Models Transaxle Service Parts Wheel & Tire Group - Flat-Free Caster Tires Wheel & Tire Group - Pneumatic Caster Tires Decal Group - Brand & Model (S/N: & Below) Decal Group - Safety & Information Decal Group - Safety & Information (ANSI EXP) Decal Group - Brand & Model (S/N: & Above) Decal Group - Safety & Operation EVAP Canister Group - S/N: & Below Evap Group - S/N: & Above " Mower Deck - Rollers & Casters " Mower Deck - Hanger Chains " Mower Deck - Housing, Covers, Spindles & Blades " Mower Deck - Pulleys, Belt & Idler Arm S/N: & Below " Mower Deck - Hanger Bars - S/N: & Below " Mower Deck - Housing, Covers & Spindles " Mower Deck - Pulleys, Belt & Idler Arm S/N: & Below " Mower Deck - Rollers " Mower Deck - Pulleys, Belt, & Idler Arm S/N: & Above Spindle SERVICE PARTS Electrical Group - Carbureted Engines w/out Remote Solenoid S/N: & Below Electrical Group - Carbureted Engines w/ Remote Solenoid S/N: & Below Electrical Group - EFI Models S/N: & Below Electrical Schematics Electrical Schematics - Kohler EFI S/N: & Below Torque Specification Chart... Inside Back Cover

4 Main Frame Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

5 Main Frame Group REF NO PART NO. QTY. DESCRIPTION BEARING, TAPERED ROLLER SEAL, GREASE WASHER, 3/4 SAE NUT, 3/4-16, HEX JAM NYLON LOCK WASHER, BELLEVILLE X CAP, LOW PROFILE, STEEL D 2 WELD, CASTER YOKE - RED 8a D 1 WELD, MAIN FRAME, S200XT (61" Models - S/N: & Below) 8b D 1 WELD, MAIN FRAME, S200XT (61" Models - S/N: ) 8c D 1 WELD, FRAME, 200XT-61" - RED (61" Models - S/N: ) 8d D 1 WELD, FRAME, 200XT-61" - RED (61" Models - S/N: & Above) 8e D 1 WELD, MAIN FRAME, S200XT/72 (72" Models - S/N: & Below) 8f D 1 WELD, FRAME, 200XT-72" - RED (72" Models - S/N: ) 8g D 1 WELD, FRAME, 200XT-72" - RED (72" Models - S/N: & Above) BOLT, 1/4-28 X 1/2, GD5 YZ GROMMET, 1-1/ CUP, BEARING (SV) GROMMET, 7/ GROMMET, 2" ID (S/N: & Above) Footnotes

6 Rear Bumper & ROPS Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

7 Rear Bumper & ROPS Group REF NO PART NO. QTY. DESCRIPTION SEAT BELT, RETRACTING - ASSM 2a D 1 WELD, BUMPER, REAR, S200XT - RED (S/N: & Below) 2b D 1 WELD, BUMPER, REAR, S200XT - RED (49L G5 Engine - S/N: ) 2c D 1 WELD, BUMPER, REAR, S200XT - RED (49M G5 Engine - S/N: ) 2d D 1 WELD, BUMPER, REAR, S200XT - RED (49L G5 Engine - S/N: & Above)(49M G5 Engine - S/N: & Above) 2e D 1 WELD, BUMPER, KOHLER, S200XT - RED (Kohler EFI Models Only) D 1 PLATE, REAR BUMPER, 61 SNP - SNP RED 4a A 1 PLATE, HEAT SHIELD - BLK (All other models - S/N: & Above) 4b D 1 PLATE, HEAT SHIELD - RED (All other models - S/N: & Below) 4c A 1 PLATE, HEAT SHIELD, KOHLER, S200XT - BLK (Kohler EFI Models Only) WASHER, 5/16 SAE X6 6 BOLT, 5/16-18 X 3/4 GD NUT, 5/16-18 HEX NYLOCK FLANGE WASHER, 1/2 SAE SCREW, 1/2-13 X 1.00, SHCS NUT, 1/2-13 HEX NYLOCK FLANGE X10 2 BOLT, 1/2-13 X 1-1/4 GD5 YZ NUT, 1/2-13 HEX NYLON LOCK A 1 PLATE, SEAT BELT ANCHOR - BLK 14-1 ROPS (Call x708 if replacing a ROPS) ROLL BAR POST, RH (SV) ROLL BAR POST, LH (SV) ROLL BAR TOP LOOP (SV) X26 2 BOLT, 1/2-13 X 3-1/4, HEX HD, GD5, YZ (SV) X28 2 BOLT, 1/2-13 X 3-1/2, HEX HD, GD5, YZ (SV) WASHER, 1/2 SAE (SV) NUT, 1/2-13 HEX NYLOCK FLANGE (SV) PIN, HITCH,.50 X 3.25 W/ LAY (SV) X1 1 HARDWARE KIT, ROPS (SV) (S/N: & Below) X1 1 HARDWARE KIT, ROPS (SV) (S/N: & Above) X12 4 BOLT, 1/2-13 X 1-1/2 GD5 YZ Footnotes

8 Seat Plate & Floor Group (S/N: & Below) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

9 Seat Plate & Floor Group (S/N: & Below) REF NO PART NO. QTY. DESCRIPTION SWITCH, PLUNGER, NO/NO SNAP-IN SEAT, 2012 (S/N: & ABOVE) SEAT, LOW COMPANION (S/N: ) SEAT, GRAY, NO LOGO, CMPT (S/N: & BELOW) SPACER,.328 ID X.66, YZ SPRING-COMP,.720ID X 1.310LG X.118 WIRE SAFETY WALK, X D 1 PLATE, SEAT SWITCH - RED X28 2 BOLT, 3/8-16 X 3-1/2 GD5 YZ SPRING, SEAT SUPPORT WASHER, 5/16 SAE X8 4 BOLT, 5/16-18 X 1 GD5 YZ NUT, 5/16-18 HEX NYLOCK FLANGE WASHER, 3/8 SAE WASHER, 1/4 FENDER NUT, 3/8-16 HEX NYLOCK FLANGE X20 1 BOLT, 3/8-16 X 2-1/2 GD5 YZ (LH SIDE S/N: & BELOW) X18 2 BOLT, 5/16-18 X 2-1/4 GD5 YZ WASHER,.34 X 1.25 X 10 GA PLATE, SEAT, RUBBER FLAP (S/N: & BELOW) D 1 PLATE, FLOOR PAN, SNP 61 - RED (S/N: & ABOVE) D 1 PLATE, FLOOR PAN, S200XT - RED (S/N: & BELOW) ASSM, SEAT PLATE W/ DECAL, S200XT, SPR RED (S/N: & ABOVE)( D) D 1 WELD, SEAT PLATE - RED (S/N: ) D 1 WELD, SEAT PLATE, S200XT - RED (S/N: & BELOW) NUT, 1/4-20 HEX NYLOCK FLANGE (S/N: & BELOW) X6 6 BOLT, 1/4-20 X 3/4, CARRIAGE (S/N: & BELOW) X1 1 SEAT BACK COVER (2012) (S/N: & ABOVE) X1 1 SEAT BACK COVER (S/N: ) X2 1 SEAT CUSHION (2012) (S/N: & ABOVE) X2 1 SEAT CUSHION (S/N: ) X3 1 ARM REST (S/N: & ABOVE) X4 1 SLIDE RAILS (S/N: & ABOVE) Footnotes

10 Seat Plate & Floor Group (S/N: & Above) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

11 Seat Plate & Floor Group (S/N: & Above) REF NO PART NO. QTY. DESCRIPTION SEAT, SPACER,.33 X.66 X 1.31 SHLDR, CZ SPRING, COMP 720ID X 1.310LG X.118WIRE SAFETY WALK, X D 1 PLATE, SEAT SWITCH - RED ASSM, SEAT PLATE W/ DECALS, S200XT - RED ( D) (S/N: & Below) ASSM, SEAT PLATE W/DECALS,200XT-SPR/MASS ( D) (S/N: & Above) D 1 PLATE, REMOVABLE FLOOR, 200XT - RED D 1 PLATE, RIGID FLOOR, 200XT - RED SPRING, SEAT SUPPORT WASHER,.34 X 1.25 X 10 GA SWITCH, PLUNGER, NO/NO SNAP-IN (S/N: & Below) SWITCH, PLUNGER, NO SINGLE POLE SNAP IN (S/N: & Above) NUT, 5/16-18, HEX, CNTR LK,ZINC PHOS/OIL KNOB-INT THR ARM 2.12WD 1.06LG MNT, VBRTN, RBBR X10 1 BOLT, 5/16-18 X 1-1/4, CARRIAGE YZ WASHER, 3/8 SAE X28 2 BOLT, 3/8-16 X 3-1/2 GD5 CZ NUT, 3/8-16 HEX NYLOCK FLANGE X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE WASHER, 5/16 SAE X8 2 BOLT, 5/16-18 X 1 GD5 YZ NUT, 5/16-18 HEX NYLOCK FLANGE X18 2 BOLT, 5/16-18 X 2-1/4 GD5 YZ Footnotes

12 Fuel Tank & Mount Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

13 Fuel Tank & Mount Group REF NO PART NO. QTY. DESCRIPTION 1A TANK, FUEL, RH (Double Tank - S/N: & Above) 1B TANK, FUEL, RH (Double Tank - S/N: & Below) 1C TANK, FENDER (Single Tank Models) 2A TANK, FUEL, LH (S/N: & Above) 2B TANK, FUEL, LH (S/N: & Below) 3A CAP, FUEL TANK, 3-1/2 NECK (S/N: & Above) 3B CAP, GASOLINE, VENTED (S/N: & Below) WASHER, 5/16 SAE WASHER, 5/16 LOCK YZ X6 12 BOLT, 5/16-18 X 3/4 GD CABLE TIE-PUSH MOUNT (Not shown) X8 10 BOLT, 5/16-18 X 1 GD5 YZ NUT, 5/16-18 HEX NYLOCK FLANGE A 1 WELD, FUEL TANK MOUNT - LH, S200XT - BLK A 1 WELD, FUEL TANK MOUNT - RH, S200XT - BLK A 1 WELD, TANK MOUNT, REAR, LH - BLK A 1 WELD, TANK MOUNT, REAR, RH - BLK 14A D 1 BRACKET, FUEL VALVE (Kawasaki Models - S/N: & Below) 14B D 1 BRACKET, FUEL VALVE (Briggs & Stratton Models - S/N: & Below) X1 2 GROMMET, FUEL GAUGE (SV) FUEL GAUGE, 12" (SV) A 1 WELD, FUEL TANK MOUNT - LH, S200XT - BLK (S/N: & Below) A 1 WELD, FUEL TANK MOUNT - RH, S200XT - BLK (S/N: & Below) A 1 WELD, FUEL TANK MOUNT - LH, 200XT - BLK (S/N: & Above) A 1 WELD, FUEL TANK MOUNT - RH, 200XT - BLK (S/N: & Above) BODY CLIP, 1/4-20 X 1/2 DEEP WASHER, 1/4 SAE NUT, 1/4-20 HEX NYLOCK FLANGE X6 8 NUT, 1/4-20 HEX NYLOCK FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE WASHER, 3/8 SAE X8 1 BOLT, 3/8-16 X 1 GD5 YZ A 1 GUARD, SEAT, LH, S200XT - BLK A 1 GUARD, SEAT, RH, S200XT - BLK A 1 PLATE, FLAP MOUNTING, S200XT - RH - BLK A 1 PLATE, FLAP MOUNTING, S200XT - LH - BLK FLAP, CONTROL, S200XT PUSH RIVET (TREE TYPE), BLACK Footnotes

14 Fuel Supply Hose & Tank Replacement Parts Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

15 Fuel Supply Hose & Tank Replacement Parts Group REF NO PART NO. QTY. DESCRIPTION VALVE, FUEL, STR. OUTLET CLAMP, HOSE, EXTERNAL, 1/2 - RED BUSHING-FUEL TANK RED RUBBER (SV) PICKUP TUBE ASSEMBLY, FUEL LINE (SV) X3 1 FUEL FILTER (SV) X47 1 HOSE, 1/4" X 47" (S/N: & Below) X54 1 HOSE, 1/4" X 54" (S/N: ) X21 1 HOSE, 1/4" X 21" (S/N: & Below) X22 1 HOSE, 1/4" X 22" (S/N: ) X42 1 HOSE, 1/4" X 42" (Kawasaki Models and Briggs & Stratton Vanguard Models) X22 1 HOSE, 1/4" X 22" (Briggs & Stratton Commercial Turf Models - Double Tank) X30 1 HOSE, 1/4" X 30" (Kohler EFI Models) X37 1 HOSE, 1/4" X 37" (Briggs & Stratton Commercial Turf Models - Single Tank) X22 1 HOSE, 1/4" X 22" X52 1 HOSE, 1/4" X 52" X34 1 HOSE, 1/4" X 34" (Kawasaki Models) X22 1 HOSE, 1/4" X 22" (Briggs & Stratton Vanguard Big Block Engines) X38 1 HOSE, 1/4" X 38" (Kohler EFI Models) X25 1 HOSE, 1/4" X 25" (Briggs & Stratton M49 & EFI Models) Footnotes

16 Instrument Control Panel Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

17 Instrument Control Panel Group REF NO PART NO. QTY. DESCRIPTION X4 3 BOLT, 1/4-20 X 1/2M ALLEN BUTTON HEAD YZ SWITCH, IGNITION, 6 POST SWITCH, BLADE ENGAGEMENT RING, SWITCH RETAINER * HOUR METER, ASSEMBLY ( ) (S/N: & Above) HOUR METER (S/N: & Below) CABLE, CHOKE CONTROL, 47 (All Other Models) CABLE, CHOKE CONTROL, 43.5" (Models & ) PLUG,.820X1.44 HOLE, BLACK PLASTIC NUT, 3/8-24 HEX O-RING, 7/8 ID X 1/16 W A 1 PLATE, CONTROL PANEL, SNP - BLK (S/N: & Below) A 1 PLATE, CONTROL PANEL, S200XT (S/N: & Above) LEVER, THROTTLE CONTROL, HEAVY-DUTY CABLE, THROTTLE, 42" X6 2 SCREW, #10-24 X 3/4 ROUND PHILLIPS NUT, #10-24 HEX NYLON LOCK Footnotes * When replacing this hour meter, please call our service department at ext

18 Instrument Control Panel Group - EFI Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart

19 Instrument Control Panel Group - EFI Models REF NO PART NO. QTY. DESCRIPTION X4 3 BOLT, 1/4-20 X 1/2M ALLEN BUTTON HEAD YZ SWITCH, IGNITION, 6 POST SWITCH, BLADE ENGAGEMENT RING, SWITCH RETAINER * HOUR METER, ASSEMBLY ( ) (S/N: & Above) LIGHT, INDICATOR, KOHLER EFI PLUG,.820X1.44 HOLE, BLACK PLASTIC NUT, #10-24 HEX NYLON LOCK O-RING, 7/8 ID X 1/16 W A 1 PLATE, CONTROL PANEL, KOHLER, S200XT - BLK (S/N: & Below) A 1 PLATE, CONTROL PANEL, 200XT, EFI (S/N: & Above) LEVER, THROTTLE CONTROL, HEAVY-DUTY CABLE, THROTTLE, 42" X6 2 SCREW, #10-24 X 3/4 ROUND PHILLIPS KEY, IGNITION, MOLDED SET (SV) COVER, PLASTIC SNAP ON (SV) NUT, PLASTIC (SV) Footnotes * When replacing this hour meter, please call our service department at ext

20 Engine & PTO Group - Briggs & Stratton - Vanguard NOTE: Unless noted otherwise, use the standard hardware torque specification chart

21 Engine & PTO Group - Briggs & Stratton - Vanguard REF NO PART NO. QTY. DESCRIPTION X1 1 MUFFLER ASSY, SERVICE PART Briggs & Stratton Big Block Vanguard Engines Only) NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) GROMMET, 7/8 (S/N: & Below) WASHER, 5/16 SAE SCREEN, SPARK ARRESTER (Not Shown) NUT, 5/16-18 HEX NYLOCK FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE CLUTCH ANCHOR PAD WASHER,.34 X 1.25 X 10 GA 10a BOLT, CRANKSHAFT, 7/16X2-3/4 (61" Models - S/N: & Above) 10b BOLT, CRANKSHAFT, 7/16X2-1/2 (61" Models - S/N: & Below) 10c BOLT, CRANKSHAFT,7/16-20X3-1/4 (72" Models - S/N: & Below) 10d BOLT, CRANKSHAFT,7/16-20X3, GD8 (72" Models - S/N: & Below) A 1 ANCHOR, CLUTCH - BLK SPACER, 1.13 X 1.75 X 1.35, YZ PULLEY, 4.75 OD X 1-1/8 BORE, BC-48 14a * CLUTCH, , WARNER (61" Models) 14b *CLUTCH, WARNER ELECTRIC CMS250 (72" Models) METRIC ADAPTER, M14-1.5" TO 3/8 NPTF (Carbureted Engines Only) ENGINE, BRIGGS AND STRATTON SCREW, SELF TAP, #8-32 X 3/8, WASH HEX CZ (Not Shown) X14 4 BOLT, 5/16-18 X 1-3/4 GD5 YZ X8 2 BOLT, 5/16-18 X 1 GD5 YZ X8 2 BOLT, 3/8-16 X 1 GD5 YZ X20 1 BOLT, 5/16-18 X 2-1/2 TFL, GD5 YZ X10 1 KEY, 1/4 SQ. X HOSE, OIL DRAIN BELLEVILLE WASHER X.442 X.089 (S/N: & Above) WASHER, 5/16 INT. TOOTH LOCK TIE WRAP, 24" LONG GROMMET, 7/8"ID, 1/4" THICK STK (S/N: & Above) MUFFLER, RIGHT OUTLET ASSY (Models & ) EXTENSION, TAILPIPE, 3", BLACK (Models & ) SCREW, SELF-TAP, #8-32 X 3/8 WASH HEX, CZ (Models & ) GASKET, EXHAUST (Models & ) SCREW-HEX SEMS LOCK WSHR 5/16-18 X (Models & ) Footnotes * For models S/N: & Below, when replacing the clutch, the jumper harness (# ) is required. *if clutch had a pigtail or if the unit s main harness was wired directly to the clutch is damaged, order

22 Engine & PTO Group - Kawasaki NOTE: Unless noted otherwise, use the standard hardware torque specification chart

23 Engine & PTO Group - Kawasaki REF NO PART NO. QTY. DESCRIPTION PULLEY, 4.75 OD X 1-1/8 BORE, BC SPACER, 1.13 X 1.75 X 1.03, CZ HOSE, OIL DRAIN, M20 X * CLUTCH, , WARNER WASHER, 1/4 SAE SET SCREW, 5/16-18 X 3/8, KNURL, W/PATCH MUFFLER, 27 HP KAWASAKI NUT, 5/16-18 HEX NYLOCK FLANGE SCREW,SELF-TAP,#8-32 X 3/8,WASH HEX, CZ CLUTCH ANCHOR PAD WASHER,.34 X 1.25 X 10 GA SPACER,.39 X 1.00 X WASHER, 5/16 SAE X8 2 BOLT, 5/16-18 X 1 GD5 YZ BOLT,HEX FLG,SER GD5 3/8-16X1-1/4PACH CZ X14 2 BOLT, 5/16-18 X 1-3/4 GD5 YZ X10 1 KEY, 1/4 SQ X 1-1/4 18a BOLT, CRANKSHAFT,7/16-20X2-3/4 (S/N: & Above) 18b BOLT, CRANKSHAFT,7/16-20X2-1/2, GD8 (S/N: & Below) ENGINE, 26HP KAWA, FX801V NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) X18 1 BOLT, 5/16-18 X 2-1/4 TFL, GD5 YZ GROMMET, 7/ HOSE, OIL DRAIN BELLEVILLE WASHER X.442 X.089 (S/N: & Above) SCREEN, SPARK ARRESTER NUT, 1/4-20 HEX NYLOCK FLANGE CLAMP, HOSE, DIA NUT, 3/8-16 HEX NYLOCK FLANGE X8 4 BOLT, 3/8-16 X 1 GD5 YZ SPACER, 1.13 X 1.75 X EXTENSION, TAILPIPE, 3" - BLACK A 1 ANCHOR, CLUTCH - BLK Footnotes * For models S/N: & Below, when replacing the clutch, the jumper harness (# ) is required

24 Engine & PTO Group - Briggs & Stratton - Commercial Turf NOTE: Unless noted otherwise, use the standard hardware torque specification chart

25 Engine & PTO Group - Briggs & Stratton - Commercial Turf REF NO PART NO. QTY. DESCRIPTION 1a MUFFLER, B&S (49L G5 Engine - S/N: & Below) 1b MUFFLER, B&S (49M G5 Engine - S/N: & Below)(Was ) NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) BELLEVILLE WASHER X.442 X.089 (S/N: & Above) WASHER, 5/16 SAE SCREEN, SPARK ARRESTER (Not Shown) NUT, 5/16-18 HEX NYLOCK FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE CLUTCH ANCHOR PAD WASHER,.34 X 1.25 X 10 GA 10a BOLT, CRANKSHAFT, 7/16X2-3/4 (61" Models - S/N: & Above) 10b BOLT, CRANKSHAFT, 7/16X2-1/2 (61" Models - S/N: & Below) 10c BOLT, CRANKSHAFT, 7/16X3-1/4 (72" Models - S/N: & Above) 10d BOLT, CRANKSHAFT, 7/16-20 X 3, GD8 (72" Models - S/N: & Below) A 1 ANCHOR, CLUTCH - BLK SPACER, 1.13 X 1.75 X 1.35, YZ PULLEY, 4.75 OD X 1-1/8 BORE, BC-48 14a * CLUTCH, , WARNER (61" Models) 14b *CLUTCH, WARNER ELECTRIC CMS250 (72" Models) WASHER, 1/4 SAE ENGINE, B&S, COMM TURF SCREW,SELF-TAP,#8-32 X 3/8,WASH HEX, CZ X14 4 BOLT, 5/16-18 X 1-3/4 GD5 YZ X8 2 BOLT, 5/16-18 X 1 GD5 YZ X8 2 BOLT, 3/8-16 X 1 GD5 YZ 21a X18 1 BOLT, 5/16-18 X 2-1/4 TFL, GD5 YZ (61" Models) 21b X20 1 BOLT, 5/16-18 X 2-1/2 TFL, GD5 YZ (72" Models) X10 1 KEY, 1/4 SQ. X HOSE, OIL DRAIN NUT, 1/4-20 HEX SERR. FLANGE WASHER, 5/16 INT. TOOTH LOCK EXTENSION, TAILPIPE, 3" - BLACK SOLENOID-4 POLE 12 VOLT DC (TROMBETTA) X5 2 BOLT-1/4-20 X 5/8 GD5 YZ GROMMET, 7/8 (S/N: & Below) MUFFLER, RIGHT OUTLET ASSY (49L G5 Engine - S/N: & Above)(49M G5 Engine - S/N: & Above) GROMMET, 7/8"ID, 1/4" THICK STK (S/N: & Above) Footnotes * For models S/N: & Below, when replacing the clutch, the jumper harness (# ) is required. *if clutch had a pigtail or if the unit s main harness was wired directly to the clutch is damaged, order

26 Engine & PTO Group - Kohler EFI NOTE: Unless noted otherwise, use the standard hardware torque specification chart

27 Engine & PTO Group - Kohler EFI REF NO PART NO. QTY. DESCRIPTION 1-1 ENGINE, 29HP KOHLER, ECV SPACER, 1.13 X 1.75 X 1.03, CZ PULLEY, 4.75 OD X 1-1/8 BORE, BC X10 1 KEY, 1/4 SQ X 1-1/ SPACER, 1.13 X 1.75 X CLUTCH, , WARNER BELLEVILLE WASHER X.442 X BOLT, CRANKSHAFT,7/16-20X3, GD X18 1 BOLT, 5/16-18 X 2-1/4 GD5 TFL, ZN WASHER,.34 X 1.25 X 10 GA NUT, 5/16-18 HEX NYLOCK FLANGE NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) X8 1 BOLT, 3/8-16 X 1 GD5 YZ A 1 ANCHOR, CLUTCH - BLK CLUTCH ANCHOR PAD NUT, 3/8-16 HEX NYLOCK FLANGE WASHER, 5/16 SAE X8 1 BOLT, 5/16-18 X 1 GD5 YZ GROMMET, 7/8 (S/N: & Below) WASHER, 5/16 LIGHT LOCK NUT, 5/16-24 JAM HOSE, OIL DRAIN WASHER, 5/16 INT. TOOTH LOCK X14 5 BOLT, 5/16-18 X 1-3/4 GD5 YZ 25-1 MUFFLER, KOHLER EFI, OIL FILTER SIDE (See Engine Service Parts - Kohler EFI) CLUTCH JUMPER W/ DIODE WARNER GROMMET, 7/8"ID, 1/4" THICK STK (S/N: & Above) Footnotes

28 Engine Service Parts - Briggs & Stratton Commercial Turf NOTE: Unless noted otherwise, use the standard hardware torque specification chart

29 Engine Service Parts - Briggs & Stratton Commercial Turf REF NO PART NO. QTY. DESCRIPTION FILTER-AIR CLEANER CA (794935) (SV) FILTER-OIL (695396) (SV) Footnotes

30 Engine Service Parts - Briggs & Stratton Vanguard Big Block NOTE: Unless noted otherwise, use the standard hardware torque specification chart

31 Engine Service Parts - Briggs & Stratton Vanguard Big Block REF NO PART NO. QTY. DESCRIPTION " AIR CLEANER ASSEMBLY (809670) AIR FILTER - INNER AIR FILTER - OUTER CAP - AIR CLEANER RUBBER DUST CAP CAP - A/C RAIN BRACKET - AIR CLEANER HOSE CLAMP - HOSE OIL FILTER Footnotes

32 Engine Service Parts - Kawasaki (FX651V - FX1000V) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

33 Engine Service Parts - Kawasaki (FX651V - FX1000V) REF NO PART NO. QTY. DESCRIPTION X1 1 AIR FILTER ASSEMBLY,22,24&26HP KAWASAKI ( ) X4 1 AIR FILTER,SECOND,FX651V THRU FX999 ENG ( ) X3 1 AIR FILTER,PRIMARY,FX 651,852, & 999 ENG ( ) X2 1 CASE, AIR FILTER, 22, 24 & 26HP KAWASAKI ( ) X8 1 DUST VALVE,AIR FILTR,22,24&26HP KAWASAKI ( ) CAP, RAIN ( ) X5 1 BRKT,AIR FILTER,22,24&26HP KAV, OUTER ( H) X6 1 BRKT,AIR FILTER,22,24&26HP KAV, INNER ( H) X9 1 BREATHER TUBE, AIR FILTR,22,24&26HP KAWA ( ) X10 1 AIR INLET TUBE,AIR FILTR,22,24&26HP KAWA ( ) CLAMP ( ) X1 1 FILTER,OIL,KAWA FS,FX651,700,FR 603 & 726CC ENG ( ) X1 1 FILTER,OIL,KAWASAKI,FX751,801,851,921,1000 ( ) KAWASAKI FX751 & LARGER ENGINES ONLY Footnotes

34 Engine Service Parts - Kohler ECV749 EFI NOTE: Unless noted otherwise, use the standard hardware torque specification chart

35 Engine Service Parts - Kohler ECV749 EFI REF NO PART NO. QTY. DESCRIPTION ELEMENT ASSEMBLY, INTERNAL (SV) ELEMENT ASSEMBLY, EXTERNAL (SV) X4 1 OIL FILTER, KOH, EFI, (SV) X3 1 OXYGEN SENSOR, KOHLER (SV) X2 1 MUFFLER KIT, KOHLER (ALSO AVAILABLE THROUGH KOHLER. KOHLER P/N: S) (SV) X1 1 MUFFLER, KOHLER, OIL FILTER SIDE (SV) Footnotes

36 Transaxle Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

37 Transaxle Drive Group REF NO PART NO. QTY. DESCRIPTION NUT, 3/8-16 HEX SERRATED FLANGE BUSHING, BRASS, 1.25X1X1.25 (S/N: & Below) SPRING, EXTENSION, SWIVEL END EYE BOLT, 3/8-16 X 5, 1 EYE WASHER,.41 X 1.75 X NUT, 3/8-16 HEX NYLOCK FLANGE (Qty: 3 - S/N: & Below) NO LONGER AVAILABLE, USE ITEM # 18 (S/N: & Below) PULLEY-IDLER, 5.00OD,.385ID,.75W, STL SPACER,.39 X 1.75 X.63, YZ (S/N: & Below) SPACER,.39 X X 2.55, SS (S/N: & Below) X12 1 BOLT, 3/8-16 X 1-1/2 GD5 YZ BELT, HB SEC, 81.2EL A 1 PLATE, IDLER ARM ADAPTER - RED (S/N: & Below) A 1 PLATE, IDLER ARM ADAPTER - BLK (S/N: & Above) X20 1 BOLT, 3/8-16 X 2-1/2 GD5 YZ X32 1 BOLT, 3/8-16 X 4 GD5 YZ (S/N: & Below) NUT, 3/8-16 HEX X16 1 BOLT, 3/8-16 X 2 GD5 YZ ASSM, IDLER ARM, PUMP DRIVE (SV)(Includes items #19-21)( A) BEARING, BALL, AXLE SPACER,.39 X.88 X 1.53, CZ SPACER, IDLER ARM, T-STYLE, CZ ASSM, IDLER ARM, PUMP DRIVE, 1/2ID, CAST (SV)(S/N: & Above) SPACER,.52 X.84 X 1.53, PM (S/N: & Above) SPACER,.52 X 1.75 X.63, CZ (S/N: & Above) SPACER, IDLER ARM, 1/2, PM (S/N: & Above) WASHER,.52 X 1.75 X.14, CZ (S/N: & Above) X36 1 BOLT, 1/2-13 X 4-1/2 GD5 YZ (S/N: & Above) NUT, 1/2-13 HEX NYLOCK FLANGE (S/N: & Above) Footnotes

38 Motion Control Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

39 Motion Control Group REF NO PART NO. QTY. DESCRIPTION BEARING, BRONZE FLANGE, 3/ BALL JOINT, 5/16-24, FEMALE SWITCH, PLUNGER, N.O BEARING, FLANGE GRIP, FOAM, 3/4 ID, 16 LONG BALL JOINT, 5/16-24, LH FEMALE NUT, 5/16-18 HEX NYLOCK FLANGE A 2 MOUNT, CONTROL ARM - BLK DAMPENER, CONTROL,#(P6709/P3610) BALL STUD, 5/16 X.50,# PC-477-2) A 1 WELD, HANDLE MOTION CONTROL, LH - BLK A 1 WELD, HANDLE MOTION CONTROL, RH - BLK (Not Shown) X8 6 BOLT, 3/8-16 X 1 GD5 YZ X10 4 BOLT, 5/16-18 X 1-1/4 GD5 YZ NUT, 3/8-16 HEX NYLON LOCK NUT, 5/16-18 HEX SERRATED FLANGE (SMALL) X14 4 BOLT- 5/16-18 X 1-3/4 GD5 TFL X14 4 BOLT, 3/8-16 X 1-3/4 GD X4 4 SCREW- #10-24 X 1/2 ROUND PHILLIPS NUT, #10-24 HEX A 1 WELD, CONTROL SHAFT, RH - S200XT - RED (Not Shown) A 1 WELD, CONTROL SHAFT, LH - S200XT- RED A 2 PLATE, HYDRO CONNECTOR, S200XT - BLK ROD, HYDRO LINKAGE - S200XT - YZ SPACER,.38 X.75 X 1.25, YZ X20 2 BOLT, 5/16-18 X 2-1/2 GD5 YZ WASHER, 5/16 SAE SCREW, 5/16-18X0.750, GR5, WHIZ-LOCK, ZC NUT, 5/16-24 HEX BOLT, 3/8-16 X 1-1/4 SHCS NUT, 5/16-24 HEX, LH Footnotes

40 Hydraulic Group S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart

41 Hydraulic Group S/N: & Below REF NO PART NO. QTY. DESCRIPTION 1a TRANS, ZT5400 INTEG, LH (61" Models - S/N: & Above) 1b TRANS, INTEGRATED, LH (61" Models - S/N: & Below) 1c TRANS, ZT-5400, LH, LONG AXLE (72" Models) 2a TRANS, ZT5400 INTEG, RH (61" Models - S/N: & Above) 2b TRANS, INTEGRATED, RH (61" Models - S/N: & Below) 2c TRANS, ZT-5400, RH, LONG AXLE (72" Models) HYDRO TANK, HYDRO-GEAR 71938, 1 LITER X1 2 FITTING, BREATHER, ZT5400 5a HOSE, OFFSET FORMED (S/N: & Above) 5b - 2 REPLACE WITH X6 HOSE QTY: 1 AND CLAMP QTY: 2 (S/N: & Below) CLAMP, #10 HOSE, STAINLESS X6 4 BOLT, 5/16-18 X 3/4 GD BODY CLIP, 5/ GA MATERIAL (S/N: & Below) D 1 GUARD, FAN, LH - RED (S/N: & Below) X6 4 BOLT, 5/16-18 X 3/4 GD5 (S/N: & Below) WASHER, 5/16 SAE NUT, 5/16-18 HEX NYLOCK FLANGE BOLT,HEX FLG,SER,GD8 1/2-13X1-1/4W/PATCH X8 5 BOLT, 1/4-20 X 1 GD5 YZ NUT, 1/4-20 HEX NYLOCK FLANGE 16a D 2 PLATE, HYDRO TANK (Kawasaki - S/N: & Below) 16b A 2 PLATE, HYDRO TANK - BLK (Briggs & Stratton - S/N: & Above) 16c D 2 PLATE, HYDRO TANK (Briggs & Stratton - S/N: & Below) CABLE TIE-PUSH MOUNT (Not Shown - S/N: & Below) D 1 GUARD, FAN, RH - RED (S/N: & Below) X6 4 BOLT, 1/4-20 X 3/ PULLEY, ZT5400 (SV) (Not Shown) FAN, ZT5400 (SV) (Not Shown) WASHER, ZT5400, SLOTTED (SV) (Not Shown) NUT, ZT5400 (SV) (Not Shown) SPACER, ANTI ROTATE, ZT5400 (SV) (Not Shown) 25a A 1 BRACKET,HYD TANK, RH - BLK (Single Tank Models) 25b A 1 BRACKET,HYD TANK, RH - BLK (Double Tank - S/N: & Above) A 1 BRACKET,HYD TANK, LH - BLK (S/N: ) CLAMP, VINYL INSULATED (S/N: & Above) A 1 BRACKET, HYD TANK, S200XT, LH - BLK (S/N: & Above) Footnotes

42 Parking Brake Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

43 Parking Brake Group REF NO PART NO. QTY. DESCRIPTION CLEVIS, 5/16-24, STEEL BEARING, BRONZE FLANGE, 3/ SWITCH, DP NO/NC SNAP-IN CABLE, PARKING BRAKE (S/N: & Below) NUT, 5/16-24 HEX NYLON LOCK WASHER, 5/16 SAE NUT, 3/8-16 HEX NYLOCK FLANGE SPACER,.32 X.75 X SPRING-COMP,.75 X.162 X 2.5 (S/N: & Below) GRIP, FOAM, 3/4 ID X 6 X X6 4 BOLT, 5/16-18 X 3/4 GD5 YZ WASHER, 1/2 USS NUT, 5/16-18 HEX NYLON LOCK NUT, 5/16-24 HEX X8 2 PIN-CLEVIS, 5/16 X 1 YZ NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) X10 3 BOLT, 5/16-18 X 1-1/4 GD5 YZ SPACER,.38 X.50 X.31, CZ X14 2 BOLT, 5/16-18 X 1-3/4 GD5 YZ BUSHING, DECK PIVOT A 1 WELD, BRAKE SHAFT - BLK A 2 PLATE, BRAKE ARM EXTENSION - BLK D 2 LINK, BRAKE LOCK - RED (S/N: & Below) SPRING, COMP, 1.1 X OD. X.085 WIRE X X10 2 BOLT, 1/2-13 X 1-1/4 GD5 YZ NUT, 1/2-13 HEX SIDE LOCK X6 2 PIN, COTTER, 1/8 X 3/ WASHER, 3/8 SAE NUT, 3/8-16 HEX SIDE LOCK COLLAR, 5/16 SET (S/N: & Above) CABLE, PARKING BRAKE, S200XT (S/N: & Above) SPRING, COMP. 1/2 ID X.140 WIRE X 3.25 (S/N: & Above) A 2 LINK, BRAKE LOCK - BLK (S/N: & Above) X10 2 BOLT, 3/8-16 X 1-1/4 GD5 Footnotes

44 Deck Lift Group - 61" Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart

45 Deck Lift Group - 61" Models REF NO PART NO. QTY. DESCRIPTION NUT, 3/8-16 HEX NYLOCK FLANGE BUSHING, 1.00 X 1.13 X 1.38, PLASTIC GREASE FITTING, 1/4-28 STRAIGHT GRIP, FOAM SPRING, EXTENSION PIN, HITCH, 1/2 X 2.00 OAL, YP X12 2 BOLT, 3/8-16 X 1-1/2 GD5 YZ BALL JOINT, 1/2-20, MALE NUT, 1/2-20 HEX JAM (S/N: & ABOVE USE QTY. 5) SPRING, DECK LIFT ASSIST NUT, 3/8-16 HEX SERRATED FLANGE RUBBER, FOOT PEDAL X10 2 BOLT, 3/8-16 X 1-1/4 GD WASHER, 1/2 SAE (S/N: ; USE QTY. 1) ROD, DECK LIFT, TWR A 1 WELD, ROD DECK LIFT - BLK D 1 WELD, DECK ADJUST LINK - SNP RED WASHER, 3/8 SAE WASHER,.390 X 1.50 X.109, YZ BOLT, 3/8-16 X 3/4, GD5, YZ WITH PATCH NUT, 1/2-13 HEX NYLOCK FLANGE A 1 WELD, PIVOT DECK LIFT, RH - S200XT - BLK (S/N: & BELOW) A 1 WELD, PIVOT DECK LIFT, LH - S200XT - BLK (S/N: & BELOW) CLEVIS, 1/2-20, STEEL X12 4 PIN, CLEVIS, 1/2 X 1 1/2, YZP X6 4 PIN, COTTER, 1/8 X 3/ A 1 PEDAL, FOOT - BLK WASHER, 3/8 GD.9 FLAT X14 4 BOLT-1/2-20 X 1-3/4 GD5 YZ (S/N: & BELOW) D 1 WELD, DECK LIFT SHAFT, S200XT - RED (S/N: & BELOW) PIVOT BLOCK, PLASTIC A 2 PLATE, PIVOT BLOCK SUPPORT - BLK X22 4 BOLT, 3/8-16 X 2-3/4 GD5 YZ X8 4 BOLT, 3/8-16 X 1 GD5 YZ X10 1 BOLT, 1/2-13 X 1-1/4 GD5 YZ COLLAR, 3/4 SPLIT (S/N: & BELOW) A 2 WELD, DECK STABILIZER - BLK (S/N: & BELOW) NUT, 1/2-20 HEX NYLON LOCK (S/N: & BELOW) SHAFT, DECK STABILIZER (S/N: & BELOW) BALL JOINT, 1/2" MALE, EXTRA CAPACITY (S/N: & BELOW) BALL JOINT, 3/4-16, MALE (S/N: & ABOVE) Footnotes

46 Deck Lift Group - 61" Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart

47 Deck Lift Group - 61" Models REF NO PART NO. QTY. DESCRIPTION X20 4 BOLT, 3/4-16 X 2-1/2 YZ GD5 (S/N: & ABOVE) NUT, 3/4-16 HEX NYLON LOCK (S/N: & ABOVE) WASHER, 3/4 SAE (S/N: & ABOVE) NUT, 3/4-16 HEX JAM (S/N: & ABOVE) A 1 WELD, DECK STABILIZER - BLK (S/N: & ABOVE) D 1 WELD, DECK LIFT, 200XT-61 - RED (S/N: & ABOVE) SPACER,.52 X 1.00 X.22, CZ (S/N: & ABOVE) A 1 WELD, PIVOT, DECK LIFT, RH, S200XT - BLK (S/N: & ABOVE) A 1 WELD, PIVOT, DECK LIFT, LH, S200XT - BLK (S/N: & ABOVE) NUT, 3/8-16 HEX JAM Footnotes

48 Deck Lift Group - 72" Models S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart

49 Deck Lift Group - 72" Models S/N: & Below REF NO PART NO. QTY. DESCRIPTION RUBBER, FOOT PEDAL GREASE FITTING, 1/4-28 STRAIGHT SPRING-EXT,.500 OD X 3.50 LG X.058 WR GRIP, FOAM BALL JOINT, 5/8-18, MALE NUT, 5/8-18, HEX JAM CLEVIS, 1/2-20, STEEL BUSHING, 1.00 X 1.13 X 1.38, PLASTIC SPRING-EXT, ODX13.25LGX.218WR, BLK PIN, HITCH, 1/2 X 2.00 OAL, YP NUT, 1/2-20 HEX JAM NUT, 3/8-16 HEX WASHER, 3/8 SAE NUT, 3/8-16 HEX NYLOCK FLANGE NUT, 1/2-13 HEX NYLOCK FLANGE BOLT, 3/8-16 X 3/4, GD5, YZ WITH PATCH A 1 PEDAL, FOOT - BLK WASHER,.390 X 1.50 X.109, YZ PIVOT BLOCK, PLASTIC ROD, DECK LIFT, TWR D 1 WELD, DECK ADJUSTER LINK - RED D 1 WELD, DECK LIFT SHAFT - RED (S/N: & Below) X10 6 BOLT, 3/8-16 X 1-1/4 GD X14 2 BOLT, 3/8-16 X 1-3/4 GD5 YZ X6 4 PIN, COTTER, 1/8 X 3/ X12 4 PIN, CLEVIS, 1/2 X 1 1/2, YZP A 2 PLATE, PIVOT BLOCK SUPPORT - BLK X22 4 BOLT, 3/8-16 X 2-3/4 GD5 YZ A 1 WELD, DECK LIFT PIVOT, RH - BLK (Not Shown) A 1 WELD, DECK LIFT PIVOT, LH - BLK X22 4 BOLT, 1/2-13 X 2-3/4 GD5 YZ PIVOT, DECK LIFT SPACER,.39 X 1.25 X 1.25, CZ X20 4 BOLT, 3/8-16 X 2-1/2 GD5 YZ ADJUSTER, DECK LIFT EYE BOLT, 1/2-20 X 4-1/4, 1 EYE, CZ D 4 BRACKET, DECK LIFT, 72 - RED BOLT,HEX FLG, SER GD8 3/8-16X1, PATCH SPACER,.52 X.87 X 1.25, CZ X20 1 BOLT, 5/8-11 X 2-1/2 GD5, CZ WASHER, 5/8 SAE (Qty: 4 - S/N: & Above) Footnotes

50 Deck Lift Group - 72" Models S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart

51 Deck Lift Group - 72" Models S/N: & Below REF NO PART NO. QTY. DESCRIPTION NUT,5/8-11 HEX NYLON LOCK A 1 WELD, ROD DECK LIFT - BLK WASHER, 1/2 GD9 YZ X6 2 BOLT, 5/16-18 X 3/4 GD WASHER, 5/16 SAE NUT, 5/16-18 HEX NYLOCK FLANGE D 2 PLATE, DECK LIFT ASSIST GREASE FITTING, 1/4-28, 90 DEGREE D 1 WELD, DECK LIFT, 200XT-72 - RED (S/N: & Above) Footnotes

52 Deck Lift Group - Spring Assist - 72" Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart

53 Deck Lift Group - Spring Assist - 72" Models REF NO PART NO. QTY. DESCRIPTION PIVOT BLOCK, PLASTIC LINK, ADJUSTABLE, SHORT NUT, 3/8-24 HEX X22 4 BOLT, 3/8-16 X 2-3/4 GD5 YZ WASHER, 3/8 SAE NUT, 3/8-16 HEX NYLOCK FLANGE D 1 WELD, PIVOT, LIFT ASSIST - RED BALL JOINT, 3/8-24 FEMALE SPRING-EXT, 1.00 ODX13.25LGX.177WR, BLK EYE BOLT, 3/8-16 X 5, 1 EYE SPACER,.38 X.50 X X12 2 BOLT, 3/8-16 X 1-1/2 GD5 YZ A 2 PLATE, PIVOT BLOCK SUPPORT - BLK Footnotes

54 Transaxle Service Parts NOTE: Unless noted otherwise, use the standard hardware torque specification chart

55 Transaxle Service Parts REF NO PART NO. QTY. DESCRIPTION X5 1 Axle Cap (SV) X2 1 Kit, Filter (SV) X3 1 Kit, Fan/Pulley (SV) X4 1 Kit, Seal (SV) Footnotes

56 Wheel & Tire Group - Flat-Free Caster Tires NOTE: Unless noted otherwise, use the standard hardware torque specification chart

57 Wheel & Tire Group - Flat-Free Caster Tires REF NO PART NO. QTY. DESCRIPTION FLAT FREE TIRE ASSEMBLY, 13 X (Includes Ref. Nos 3 & 4) WASHER, 1/2" SAE SX2 4 BEARING, TAPER ROLLER (SV) SX3 4 GREASE SEAL (SV) ADAPTER, CASTER AXLE, CZ (S/N: & Below)(2 per tire) X72 2 BOLT, 1/2-13 X 9" GD5 YZ NUT, 1/2-13 HEX NYLOCK FLANGE TIRE ASSM, 24X , SOLID (S/N: & Below) TIRE/WHEEL ASM, 24X , TURF SMART (S/N: & Above) X1 2 TIRE, REAR, 24 x 12 x 12 (SV) (S/N: & Below) X1 2 TIRE, 24X , TURF SMART (SV) (S/N: & Above) WHEEL ASSEMBLY, 12 x 8.5 (SV) NUT, 1/2-20, FOR WHEEL BOLT SILVER SX4 2 BEARING, RACE (SV) (Not shown) NUT, BEARING ADJUSTER, AXLE (S/N: & Above)(1 per tire) BEARING ADJUSTER, SPACER, 7.062LG (S/N: & Above)(1 per tire) DEBRIS COVER, CASTER WHEELS (S/N: & Above)(2 per tire) Footnotes

58 Wheel & Tire Group - Pneumatic Caster Tires NOTE: Unless noted otherwise, use the standard hardware torque specification chart

59 Wheel & Tire Group - Pneumatic Caster Tires REF NO PART NO. QTY. DESCRIPTION TIRE ASSY, 13 X 6.5 SILVER TIRE X1 2 WHEEL ASSEMBLY SX2 4 BEARING, TAPERED CONE SX3 4 SEAL, GREASE ADAPTER, CASTER AXLE, CZ (S/N: & Below)(2 per tire) X72 2 BOLT, 1/2-13 X 9 GD5 YZ NUT, 1/2-13 HEX NYLOCK FLANGE TIRE ASSM, 24X , SOLID (S/N: & Below) TIRE/WHEEL ASM, 24X , TURF SMART (S/N: & Above) X1 2 TIRE, 24 X 12 X 12 (S/N: & Below) X1 2 TIRE, 24X , TURF SMART (SV) (S/N: & Above) WHEEL, 12 X 8.5, SOLID NUT, 1/2-20, FOR WHEEL BOLT SILVER WASHER, 1/2 SAE SX4 2 RACE, BEARING (SV) NUT, BEARING ADJUSTER, AXLE (S/N: & Above)(1 per tire) BEARING ADJUSTER, SPACER, 7.062LG (S/N: & Above)(1 per tire) DEBRIS COVER, CASTER WHEELS (S/N: & Above)(2 per tire) Footnotes

60 Decal Group - Brand & Model (S/N: & Below) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

61 Decal Group - Brand & Model (S/N: & Below) REF NO PART NO. QTY. DESCRIPTION DECAL, 61 (61" Models) DECAL, 72 (72" Models) DECAL, SNAPPER PRO, S200XT LABEL, BRIGGS & STRATTON LOGO (Briggs & Stratton Powered Models - S/N: & Below) DECAL, SNAPPER PRO, FRONT DECAL, SNAPPER PRO, HEAT DECAL, icd CUTTING SYSTEM Footnotes

62 Decal Group - Safety & Information NOTE: Unless noted otherwise, use the standard hardware torque specification chart

63 Decal Group - Safety & Information REF NO PART NO. QTY. DESCRIPTION DECAL, MAIN SAFETY DECAL, DANGER, MOWER DISCHARGE,9.75X DECAL, DANGER, MOWER DECAL, DANGER, FIRE DECAL, DANGER, FIRE (SP) DECAL, WARNING, PINCH POINT DECAL, TRANSAXLE RELEASE, S200XT DECAL, BELT & BLADE, S200XT DECAL, FUEL VALVE DECAL, DECK HEIGHT, 1-1/2 TO 6, S200XT DECAL, THROTTLE CONTROL DECAL, IGNITION SWITCH DECAL, HYDRAULIC OIL, SAE 20W DECAL, FUSE LOCATION DECAL, WARNING, ROLL BAR (SV) NLA - DECAL, WARNING OVERHANG, ROPS (SP) 17-1 ORDER PART NUMBERS & NLA - DECAL, WARNING & CAUTION, ROPS (SP) DECAL, WARNING, ROLL BAR DECAL, WARNING, ROLL BAR, SP DECAL, WARNING, HAND IN BELT, ENG ONLY DECAL, WARNING, HAND IN BELT, SPA ONLY Footnotes

64 Decal Group - Safety & Information (ANSI EXP) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

65 Decal Group - Safety & Information (ANSI EXP) REF NO PART NO. QTY. DESCRIPTION DECAL, MAIN SAFETY, ANSI CE DECAL, FIRE ANSI EXPORT DECAL, PINCH POINT, CE DECAL, DANGER, MOWER DECK, ANSI EXP DECAL, DANGER DISCHARGE ANSI EXPORT DECAL, WARNING, ROLL BAR, CE DECAL, TRANSAXLE RELEASE, S200XT (Located Under Seat) DECAL, BELT & BLADE, S200XT (Located Under Seat) DECAL, FUEL VALVE DECAL, DECK HEIGHT, 1-1/2 TO 6, S200XT DECAL, THROTTLE CONTROL DECAL, IGNITION SWITCH DECAL, HYDRAULIC OIL, SAE 20W DECAL, FUSE LOCATION DECAL, PARKING BRAKE SYMBOLS Footnotes

66 Decal Group - Brand & Model (S/N: & Above) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

67 Decal Group - Brand & Model (S/N: & Above) REF NO PART NO. QTY. DESCRIPTION DECAL, 61 (61" Models) DECAL, 72 (72" Models) DECAL, SNAPPER PRO, S200XT (2014) LABEL, BRIGGS & STRATTON LOGO (Briggs & Stratton Powered Models - S/N: & Below) DECAL, SNAPPER PRO LOGO, MEDIUM DECAL, SNAPPER PRO LOGO, LARGE DECAL, icd CUTTING SYSTEM DECAL, MODEL SERIES, S200XT, EFI (Models with Briggs & Stratton EFI engines) Footnotes

68 Decal Group - Safety & Operation NOTE: Unless noted otherwise, use the standard hardware torque specification chart