Parts Manual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 POWER UNIT MODELS MOWER MODELS SPE140KW SPE151KW SPEL150KH

Size: px

Start display at page:

Download "Parts Manual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 POWER UNIT MODELS MOWER MODELS SPE140KW SPE151KW SPEL150KH"

Brett Barton
5 years ago
Views:

1 Parts Manual for MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 POWER UNIT MODELS SPE1250KW SPE131KW SPE140KW SPE150KH SPE151KW SPEL150KH MOWER MODELS SPE360 SPE361 SPE481 McDonough, GA, U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 6, 10/21/2005

3 Table Of Contents PAGE GROUP 4 PISTOL GRIP HANDLE & CONTROL ASSEMBLIES 8 LOOP HANDLE & CONTROLS (Traction) 10 LOOP HANDLE & CONTROLS (Shift Lever) 12 FUEL TANK & BRACKET ASSEMBLY 14 TRANSMISSION DRIVE GROUP 16 REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES 20 TRACTION, REAR WHEEL ASSEMBLY 22 BRAKE ASSEMBLY 24 LEFT & RIGHT IDLER PULLEY ASSEMBLIES 26 ENGINE GROUP 30 CASTER, WHEEL & TIRE ASSEMBLY 32 36" MOWER DECK ASSEMBLY 36 36" DECK IDLER ASSEMBLY 38 48" MOWER DECK ASSEMBLY 40 48" DECK IDLER ASSEMBLY 42 CUTTER HOUSING ASSEMBLY 44 DECALS (Pt. 1) 46 DECALS (Pt. 2) 48 ELECTRICAL COMPONENTS (Pistol Grip Handle) 50 ELECTRICAL COMPONENTS (Loop Handle) 52 WIRING SCHEMATIC (Pistol Grip Handle) 54 WIRING SCHEMATIC (Loop Handle) SERIES 0 & 1 3

4 PISTOL GRIP HANDLE & CONTROL ASSEMBLIES 4 SERIES 0 & 1

5 PISTOL GRIP HANDLE & CONTROL ASSEMBLIES Item Part No Qty Description Note CLEVIS PIN (all models except SPEL150KH) ROD, Brake (3/8-16 thread) ROD, Traction (3/8-16 thread) WELDMENT, Drive Lever (Pistol Grip) COTTER PIN, 5/16 Self Lock CLEVIS PIN, 3/16 x 1-3/ SCREW, #10-24 x 1/2 Hex Washer Self-Tap 8A SPRING, Torsion, LH, Drive Lever 8B SPRING, Torsion, RH, Drive Lever LATCH, Express BRACKET, Shift Handle GRIP, Latch 12A WELDMENT, Traction Link, Upper LH 12B WELDMENT, Traction Link, Upper RH SWIVEL, Brake Link- PM COTTER PIN, 1/2 Self-Locking SWIVEL, Brake Link- PM SPRING, Friction Pack WASHER, 3/8 SAE Flat NUT, 3/8-16 Hex Nyloc GRIP, Vinyl.937 x 4-1/ WELDMENT, Pistol Grip Handle SWITCH, Seat (Normally Closed) replaces p/n A WELDMENT, Traction Link, Lower, RH 22B WELDMENT, Traction Link, Lower, LH SWIVEL, 3/8-16 Internal Thread NUT, 1/2-27 Hex (Special) SWITCH, Toggle (Indak H671A) NUT, 5/8-32 Hex (Ignition Switch) WASHER, 5/8 Internal Tooth Lock SWITCH, Ignition, 2-Pole, Recoil Start WASHER, Nylon (Wear Spacer) LEVER, Shift GRIP, Flat Bar (Black) GRIP, 3/4 ID x 4 Textured SCREW, 3/8-16 x 1-1/2 Hex Head Cap, GR SHIFT ROD, Express (3/8-16 thread) Footnotes: NOTE 1: Part Number & revision stamped on part SERIES 0 & 1 5

6 PISTOL GRIP HANDLE & CONTROL ASSEMBLIES 6 SERIES 0 & 1

7 PISTOL GRIP HANDLE & CONTROL ASSEMBLIES Item Part No Qty Description Note WIRING HARNESS, Pistol Grip see also Pistol Grip Electrical Components page BOLT, 3/8-16 x 1 Square Neck Carriage, GR CONTROL, Throttle, 42/.88 (Kawasaki) Capro ; replaces 22354; see Footnote SCREW, 1/4-20 x 3 Hex Head Cap, GR WASHER, 1/4 Flat SPACER, Brake (Outer) ROLL PIN, 5/ SPACER, Brake NUT, 1/4-20 Hex Nyloc 44A GRIP, Pistol OPC (RH) (Weldment) 44B GRIP, Pistol OPC (LH) (Weldment) KEY, Ignition (Pair) Footnotes: NOTE 1: Part Number & revision stamped on part SERIES 0 & 1 7

8 LOOP HANDLE & CONTROLS (Traction) 8 SERIES 0 & 1

9 LOOP HANDLE & CONTROLS (Traction) Item Part No Qty Description Note LOOP HANDLE, Express (Weldment) SWITCH, OPC (NC) SCREW, #12-14 x 1/2 Hex Flange Self-Tap ROD, Pivot BUSHING, 1/2 Machine E-RING, 1/ LEVER, Traction RH (Weldment) LEVER, Traction LH (Weldment) PLATE, Neutral Latch SPACER, Neutral Latch PIN, Shoulder LATCH, Neutral (Weldment) CABLE TIE, 7 not shown VINYL GRIP,.313 Dia. x 3-3/4 long BEARING BAIL, Operator Presence Control (Weldment) BOLT, 1/4-20 x 1-3/4 Hex Head Cap, GR ROD, Operator Presence Control SPRING, OPC PANEL, Console LH SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap SCREW, 1/4-20 x 3/4 Hex Washer Self-Tap SWITCH, Toggle (Indak H671A) NUT, 1/2-27 (Special) THROTTLE CONTROL (Kohler) Capro p/n ; not shown GREASE FITTING (1/2-28 thread) NUT, 1/4-20 Hex Jam SCREW, 3/8-16 x 3-1/4 Hex Head Cap, GR NUT, 3/8-16 Hex Nyloc Footnotes: (Model SPEL150KH only) SERIES 0 & 1 9

10 LOOP HANDLE & CONTROLS (Shift Lever) 10 SERIES 0 & 1

11 LOOP HANDLE & CONTROLS (Shift Lever) Item Part No Qty Description Note SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap also shown on previous page SCREW, 1/4-20 x 3/4 Hex Washer Self-Tap also shown on previous page NUT, 3/8-16 Hex Nyloc also shown on previous page PANEL, Console RH SWITCH, On-Off WASHER, 5/8 Internal Tooth Lock NUT, 5/8-32 Hex (Special) KEY, Ignition (Pair) BRACKET, Shift Handle BOLT, 3/8-16 x 1 Square Neck Carriage, GR SCREW, 3/8-16 x 1-1/2 Hex Head Cap, GR SPACER, Wear SHIFT LEVER SPRING, Friction Pack WASHER, 3/8 SAE Flat GRIP, Flat Bar (Black) ROD, Shift (21-1/2 long, 3/8-16 thread) COTTER PIN, 1/2 Self-Locking SWIVEL, Brake Link, 3/8-16 thread.019 Dia. Hole (PM) WASHER, 5/16 Flat PIN, 5/16 x.94 Clevis ROD, Traction (22 Long, 3/8-16 Thread) SWIVEL, 3/8-16 Thread,.109 Dia. Hole TRACTION LINK, Lower Left (Weldment) TRACTION LINK, Lower Right (Weldment) TRACTION LINK, Upper Right (Weldment) TRACTION LINK, Upper Left (Weldment) WIRING HARNESS, Loop Handle (not shown) See Loop Handle Electrical Components page SWIVEL,.406 &.109 Dia. Holes ROD, Brake (37-3/4 Long, 3/8-16 Thread) COTTER PIN, 5/16 Self Lock Footnotes: (Model SPEL150KH only) SERIES 0 & 1 11

12 FUEL TANK & BRACKET ASSEMBLY 12 SERIES 0 & 1

13 FUEL TANK & BRACKET ASSEMBLY Item Part No Qty Description Note TANK BRACKET GROUP (Incl. Items 1A, 1B & 3 thru 17) TANK BRACKET GROUP (Incl. 1B, 2B & 3-20) used on Model SPEL150KH only 1A TANK BRACKET, Express 1B TANK BRACKET, Express (Loop handle) not shown 2A TANK, Fuel (with cap) 2B CAP, Fuel Tank STRAP, Tank SCREW, #10-24 x 2-1/2 Pan Head Machine NUT, #10-24 Hex Nyloc ASSEMBLY, Shift Bellcrank, Express (Includes 3 Items listed below) WELDMENT, Shift Bellcrank FITTING, 3/16 Lube BEARING, 9/16 Flange BOLT, 3/8-16 x 2.44 Shoulder WASHER, 9/16 Flat (Narrow Type) ASSEMBLY, Shift Link, Express (Incl. Items 10 thru 12) BALL JOINT ROD, 1/4-28 x 2.71 Threaded NUT, 1/4-28 Hex, GR 5 or B or WASHER, 1/4 Split Lock NUT, 1/4-28 Hex Nyloc NUT, 3/8-16 Hex Center lock BOLT, 3/8-16 x 1 Short Neck Carriage, GR NUT, 3/8-16 Hex Nyloc TANK BRACKET, Upper BOLT, 5/16-18 x 1 Short Neck Carriage, GR NUT, 5/16-18 Hex Nyloc Footnotes: SERIES 0 & 1 13

14 TRANSMISSION DRIVE GROUP 14 SERIES 0 & 1

15 TRANSMISSION DRIVE GROUP Item Part No Qty Description Note RING, 3/4 External Retaining Truarc p/n WASHER, 3/4 x 1-1/8 x.06 Flat PULLEY, Trans Output, 5.5 Dia., 2RA BELT, Traction, 2RAX Sect. Eff. Length 53.4 Dayco p/n ; Neoprene Compound Polyester Cord TORQUE BRACKET TRANSMISSION, Peerless, 5-Speed SWITCH, Transmission (NO) SHIFT ARM, Express WASHER 1/4 Bellville BOLT, 1/4-28 x 5/8 Hex w/nyloc Patch, GR PULLEY, Transmission Input KEY, #9 Woodruff RING, External Retaining Truarc p/n V-BELT, HA, Effective Length Dayco p/n SUPPORT, Transmission SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap BOLT, 5/16-18 x 1 Square Neck Carriage, GR NUT, 5/16-18 Hex Nyloc SCREW, 5/16-18 x 4-1/2 Hex Head Cap, GR SPACER, Transmission KEY, 3/16 Square x WASHER, Fiber RETAINER, 5/16 Bolt Footnotes: SERIES 0 & 1 15

16 REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES 16 SERIES 0 & 1

17 REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES Item Part No Qty Description Note NUT, 3/8-24 Hex Nyloc STUD, Shoulder (3/8-24 thread w/snap-ring Groove) 3A IDLER ASSY, Upper Left (see Footnote 1) all models except SPEL150KH 3B IDLER ASSY, Upper Left Model SPEL150KH only 3C IDLER ASSY, Lower Left all models 4A IDLER ASSY, Upper Right all models except SPEL150KH 4B IDLER ASSY, Upper Right Model SPEL150KH only 4C IDLER ASSY, Lower Right all models NUT, 3/8-16 Hex Nyloc RETAINER, 5/8 Bolt not shown; replaced by item SPRING, Extension FRAME, Engine (Weldment) BOLT, 3/8-16 x 1 Square Neck Carriage, GR BRACKET, Anti-Spin replaces NUT, 5/16-18 Hex Nyloc ASSEMBLY, Brake Band, RH all models except SPE131KW ASSEMBLY, Brake Band, 6 Thomas Model SPE131KW only SPRING, Extension ASSEMBLY, Idler Arm BOLT, 1/2-13 x 1-1/4 Hex Flange Lock, GR WASHER, 9/16 Flat (Narrow Type) SHOULDER BOLT, 3/8-16 x 2-7/ SCRAPER, Wheel Pulley BUSHING, 1 x 14 Ga Machine ASSEMBLY, Wheel/Drum/Pulley E RING, Retaining Truarc p/n X SCREW, 3/8-16 x 2 Hex Head Cap, GR BOLT, 5/16-18 x 1 Short Neck Carriage, GR BUSHING, Machine, 5/ NUT, 3/8-16 Hex, GR 5 or B ASSEMBLY, Brake Band, LH all models except SPE131KW ASSEMBLY, Brake Band, 6 Thomas Model SPE131KW only WELDMENT, Brake Stud DECAL, Caution see Decal page RING, 5/8 External Retaining Truarc p/n STUD, Fender Mount (3/8-16 thread, both ends) 31A BELT COVER, Express all models except SPE131KW Footnotes: NOTE 1: For components see L & R Idler Pulley Assembly page. SERIES 0 & 1 17

18 REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES 18 SERIES 0 & 1

19 REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES Item Part No Qty Description Note 31B BELT COVER, Express Model SPEL150KH only WASHER, 1/2 Split Lock WINGNUT, 3/8-16 w/nylon Ring NUT, 3/8-16 Hex Center Lock NUT, 1/2-13 Hex, GR B BOLT, 3/8-16 x 2 Short Neck Carriage, GR WELDMENT, Idler Arm, Express LUBE FITTING, 3/16 Press-In FLANGE BEARING, 9/16 I.D IDLER, V-Belt, 3.56 O.D. Footnotes: NOTE 1: For components see L & R Idler Pulley Assembly page. SERIES 0 & 1 19

20 TRACTION, REAR WHEEL ASSEMBLY 20 SERIES 0 & 1

21 TRACTION, REAR WHEEL ASSEMBLY Item Part No Qty Description Note ASSEMBLY, Tire & Hub (Includes Items 2 thru 6) ASSEMBLY, Tire & Hub used on SPE151KW; see Footnote WELDMENT, Rim, 16 Tires WELDMENT, Rim, Gray, Pro Express BALL BEARING, Wheel qty 2 per rear wheel assembly AIR VALVE, Snap-In qty 1 per rear wheel assembly FITTING, 1/4-28 Straight Lube qty 1 per rear wheel assembly TIRE, 16 x Tubeless, Kenda 4-Ply TIRE, 16 x Turf Master 4-Ply SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR PULLEY, Traction, DRUM, Brake SPACER,.390 I.D. x 3/4 O. D. x.465 thick WASHER,.32 x.58 x.08 Split Lock Footnotes: NOTE 1: is comprised of & items SERIES 0 & 1 21

22 BRAKE ASSEMBLY 22 SERIES 0 & 1

23 BRAKE ASSEMBLY Item Part No Qty Description Note 1A WELDMENT, Brake Arm, RH 1B WELDMENT, Brake Arm, RH used on SPE151KW 1C WELDMENT, Brake Arm, LH 1D WELDMENT, Brake Arm, LH used on SPE151KW WELDMENT, Brake Mount Stud WELDMENT, Brake Link NUT, 3/8-16 Hex, GR 5 or B ASSEMBLY, Brake Band, 6 Thomas SCREW, 3/8-16 x 2 Hex Head Cap, GR BUSHING, 5/8 I.D. x 1 O.D. Machine RETAINER, 3/8 Bolt LINK, Brake RETAINER, 5/8 Bolt LUBE FITTING, 3/16 Press-In NUT, 3/8-16 Hex Nyloc Footnotes: SERIES 0 & 1 23

24 LEFT & RIGHT IDLER PULLEY ASSEMBLIES 24 SERIES 0 & 1

25 LEFT & RIGHT IDLER PULLEY ASSEMBLIES Item Part No Qty Description Note IDLER ASSY, Upper Left all models except SPEL150KH IDLER ASSY, Upper Left Model SPEL150KH only IDLER ASSY, Lower Left all models IDLER ASSY, Upper Right all models except SPEL150KH IDLER ASSY, Upper Right Model SPEL150KH only IDLER ASSY, Lower Right all models WELDMENT, Idler Arm, UL/LR WELDMENT, Idler Arm Model SPEL150KH only WELDMENT, Idler Arm, UR/LL WELDMENT, Idler Arm Model SPEL150KH only LUBE FITTING, 3/16 Press-In SCREW, 3/8-16 x 2-1/4 Hex Head Cap, GR WASHER,.38 x.68 x.09 Split Lock WASHER, 3/8 SAE Flat PULLEY- Idler 3-1/ NUT, 3/8-16 Hex, GR 5 or B Footnotes: SERIES 0 & 1 25

26 ENGINE GROUP 26 SERIES 0 & 1

27 ENGINE GROUP Item Part No Qty Description Note CLAMP, Fuel Hose LINE, Fuel, 1/4 I.D. x 1/2 O.D. x 8-1/ LINE, Fuel, 1/4 I.D. x 1/2 O.D. x LINE, Fuel, 1/4 I.D. x 1/2 O.D. x 3-1/ VALVE, Fuel FILTER, In-Line CLAMP, Fuel Hose or RECTIFIER/REGULATOR, Kawasaki CAPACITOR, Kawasaki Engine 9A HARNESS, Wiring Pigtail 9B HARNESS, Wiring Pigtail used on SPE131KW BRACKET, Capacitor ENGINE, Kawasaki 12.5 HP (shown) (Mod. No. FB460V-E536) see Footnote ENGINE, Kawasaki 13 HP (Mod. No. FH381V-AS02) ENGINE, Kawasaki 14 HP (Mod. No. FC420V-HS09) ENGINE, Kawasaki 15 HP Express (Mod. No. FH430V-AS02) ENGINE, Kohler 15 HP (Mod. No. FH430V-AS02) 12A BUSHING, 1 x 14 Ga Machine 12B SPACER, Ogura Clutch PULLEY, Engine CLUTCH, Electric (Warner p/n ) CLUTCH, Electric (Ogura p/n EXM3XR) used on SPE131KW CLUTCH, Electric (Ogura model GT2.5 SN01) use with items 12B, 34 and & SCREW, M8x1.25x25 Hex Head Cap, Class 8.8 used on Kawasaki Models SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR 5 used on Kohler Models SCREW, M x 65 Hex Head Cap w/nyloc patch SCREW, 7/16-20 x 3 Hex Head Cap Grade 5 w/nyloc patch SCREW, 7/16-20 x 2-1/2 Hex Head Cap, GR 5 special head SCREW, 7/16-20 x 2-1/2 Hex Head Cap, GR 5 w/nyloc patch; used on SPE151KW 17A WASHER,.468 x 1.38 x.25 Flat 17B SPACER, Clutch WASHER, 7/16 Split Lock or WASHER,.32 x.58 x.08 Split Lock BOLT, 5/16-18 x 1 Short Neck Carriage, GR NUT, 5/16-18 Hex Nyloc SCREW, 1/4-20 x 1-1/4 Hex Head Cap NUT, 1/4-20 Hex Nyloc Footnotes: NOTE 1: Purchase engine & engine parts, other than those listed, from engine manufacturer dealer. SERIES 0 & 1 27

28 ENGINE GROUP 28 SERIES 0 & 1

29 ENGINE GROUP Item Part No Qty Description Note KEY, 1/4 Square x KEY, 1/4 Square w/bevel KEY, 1/4 Square x 2-1/2 used on SPE131KW KEY, 1/4 Square x 2-1/ OIL VALVE ASSEMBLY WIRE, Kohler Engine Ground SPACER, Crankshaft BUMPER, Door (not shown) used on Kohler 15HP Model ADAPTER, Oil Drain (not shown) (Kawasaki p/n ) O-RING (Kawasaki p/n 670D-2016) BUMPER, Electric Clutch WASHER, Rectangular Steel SCREW, 5/16-18 x 1-1/4 Hex Head Cap, GR NUT, 5/16-18 Hex Top Lock, GR B BRACKET, Anti-Spin use with Clutch Footnotes: NOTE 1: Purchase engine & engine parts, other than those listed, from engine manufacturer dealer. SERIES 0 & 1 29

30 CASTER, WHEEL & TIRE ASSEMBLY 30 SERIES 0 & 1

31 CASTER, WHEEL & TIRE ASSEMBLY Item Part No Qty Description Note ASSEMBLY, Wheel & Tire- Gray (Incl. Items 3 & 4) ASSEMBLY, Wheel & Tire- White (Incl. Items 2, 3, 5, 16, 17 & 18B) ASSEMBLY, Wheel & Tire- Gray (Incl. Items 2, 3, 5, 16, 17 & 18C) RETAINER, Flanged quantity shown is per tire TIRE, 9 x , 4 Ply Smooth Tread ASSEMBLY, Wheel (Incl. items 2, 5, 16, 17 & 18A) BEARING, Roller quantity shown is per tire SLEEVE, Axle quantity shown is per tire NUT, 1/2-13 Hex Nyloc quantity shown is per tire BOLT, 1/2-13 x 5-1/2 Hex Head Cap, GR 5 quantity shown is per tire WELDMENT, Caster PIN, Lynch 7/16 Heavy Duty SPACER, Caster quantity shown is per tire SPACER, Powdered Metal quantity shown is per tire BUSHING, 1 quantity shown is per tire BUSHING, Caster FITTING, 1/4-28 Straight Lube VALVE STEM quantity shown is per tire FITTING, 1/ Degree Lube quantity shown is per tire 18A RIM, One Piece Steel, Gray quantity shown is per tire 18B RIM, One Piece Steel, White quantity shown is per tire 18C RIM, One Piece Steel 4 x 1-3/8 Bore quantity shown is per tire Footnotes: *Quantity per tire SERIES 0 & 1 31

32 36" MOWER DECK ASSEMBLY 32 SERIES 0 & 1

33 36" MOWER DECK ASSEMBLY Item Part No Qty Description Note RING, 1 External Retaining DECAL, Warning (CPSC Cut Finger) DECAL, Warning DECAL, Danger, Guard, Catcher English & Spanish KNOB, Hood (5/16-18 thread) DECAL, Caution- Operator Instruction SPRING, Chute V-BELT, 36 Deck Drive Sect. HB (Nom. Effective Length: ) HINGE PIN, Chute SPRING, Idler SCREW, 5/16-18 x 4-1/2 Hex Head Cap, GR COTTER PIN, 3/32 x 1 12A DECAL, SNAPPER Pro w/trademark 12B DECAL, SNAPPER Pro 13A DEFLECTOR, 36 (Weldment) 13B CHUTE, 36 Ansi Compliant (Weldment) used on SPE151KW COVER, PIVOT, Idler Arm (Weldment) ASSEMBLY, Idler Arm, ASSEMBLY, Caster (Red) WELDMENT, 36 Deck, Fixed Height, Express FITTING, 1/4-28 Straight Lube NUT, 3/8-16 Hex Nyloc BOLT, 3/8-16 x 1 Hex Head Cap, GR SCREW, 3/8-16 x 2 Hex Head Cap, GR RETAINER, 3/8 Bolt BOLT, 1/2-13 x 1-1/4 Hex Flange Lock, GR WASHER, 3/8 I.D. Flat SPACER NUT, 5/16-18 Hex Flange Lock, GR NUT, 3/8-16 Hex Flange Lock WASHER, 1/2 Split Lock NUT, 1/2-13 Hex, GR B WASHER, 13/32 Flat DECAL, 36 Deck DECAL, 36 Silver PAD Footnotes: SERIES 0 & 1 33

34 36" MOWER DECK ASSEMBLY 34 SERIES 0 & 1

35 36" MOWER DECK ASSEMBLY Item Part No Qty Description Note BOLT, 3/8-16 x 3/4 Short Neck Carriage, GR BUSHING, Caster ASSEMBLY, Spindle not shown; see Cutter Housing Assembly page Footnotes: SERIES 0 & 1 35

36 36" DECK IDLER ASSEMBLY 36 SERIES 0 & 1

37 36" DECK IDLER ASSEMBLY Item Part No Qty Description Note PULLEY, Idler (5.00 O. D.) NUT, 3/8-16 Hex Nyloc WASHER, 7/16 I.D. x 1 O.D RING, 1 External Retaining BUSHING IDLER ARM, 36 (Weldment) FITTING, 1/4-28 Straight Lube BOLT, 3/8-16 x 1 Hex Head Cap, GR PIVOT, Idler Arm (Weldment) SCREW, 3/8-16 x 3-1/4 Hex Head Cap, GR SPACER BRACKET, Idler (Pro 36) BOLT, 3/8-16 x 1 Hex Flange Lock, GR NUT, 3/8-16 Hex Center Lock, GR 5 or B RETAINER, Belt - Idler Footnotes: SERIES 0 & 1 37

38 48" MOWER DECK ASSEMBLY 38 SERIES 0 & 1

39 48" MOWER DECK ASSEMBLY Item Part No Qty Description Note DECAL, Warning (CPSC Cut Finger) DECAL, Warning DECAL, Danger, Guard, Catcher English & Spanish KNOB, Hood (5/16-18 thread) DECAL, Caution- Operator Instruction PIVOT, Roller Pin (Weldment) WASHER, 5/8 Flat SPRING, Chute PULLEY, Driven 5-3/4 O.D V-BELT, Secondary 48 (113 Long) V-BELT, Primary 48 (66 Long) SPRING, Primary HINGE PIN, Chute SPRING, Idler STANDOFF, 4-1/2 Long (5/16-18 thread top; 3/8-16 thread bottom) COTTER PIN, 3/32 x DECAL, SNAPPER Pro w/trademark DECAL, SNAPPER Pro 17A DEFLECTOR, 48 Chute (Weldment) 17B ASSEMBLY, Discharge Chute incl. items 24 (4), 29, 30, 31 & 32 (4) COVER ASSEMBLY, Caster Red (Fixed Deck) not shown; see Caster, Wheel & Tire Assembly page WELDMENT, 48 Deck (Fixed Height) includes 4 of item ASSEMBLY, Idler - 3 Spindle Deck FITTING, 1/4-28 Straight Lube FITTING, Lube Press-In for 3/16 hole ROLLER, Low Density Polyethylene NUT, 3/8-16 Hex Nyloc BOLT, 3/8-16 x 1 Hex Head Cap, GR SCREW, 3/8-16 x 2 Hex Head Cap, GR BUSHING, Caster NUT, 3/8-16 Hex Flange Lock ASSEMBLY, Spindle not shown; see Cutter Housing Assembly page WELDMENT, 48 Chute CHUTE, Rubber DEFLECTOR, Bottom BOLT, 3/8-16 x 1-1/4 Square Neck Carriage, GR 5 Footnotes: SERIES 0 & 1 39

40 48" DECK IDLER ASSEMBLY 40 SERIES 0 & 1

41 48" DECK IDLER ASSEMBLY Item Part No Qty Description Note PULLEY, Idler PULLEY, Flat Idler, 5 O.D NUT, 3/8-16 Hex Center Lock, GR 5 or B RING, 1 External Retaining BUSHING WELDMENT, Idler Arm, Secondary WELDMENT, Idler Arm, Primary SPACER, Idler Pulley WASHER, 3/8 Flat or SCREW, 3/8-16 x 2 Hex Head Cap, GR BOLT, 3/8-16 x 3-1/4 Hex Head Cap, GR FITTING, 1/4-28 Straight Lube WELDMENT, Idler Pivot RETAINER, Belt - Idler BUSHING, Machine Footnotes: SERIES 0 & 1 41

42 CUTTER HOUSING ASSEMBLY 42 SERIES 0 & 1

43 CUTTER HOUSING ASSEMBLY Item Part No Qty Description Note BEARING, Sealed WASHER, Spindle SNAP-RING, Spindle Shaft ASSEMBLY, Spindle Shaft SPACER, Bearing SPACER, Blade BLADE, 18 replaces (for 36 deck) BLADE, 16-1/2 replaces (for 48 deck) WASHER, Beveled BOLT, 5/8-11 x 7-1/2 Hex Head Cap, GR 5 replaces FITTING, 1/4-28 Straight Lube HOUSING, Cutter see Footnote VENT, Spindle BOLT, 3/8-16 x 1-1/4 Rib Necked PULLEY, 5-3/4 O.D. for 36 deck NUT, 5/8-11 Hex Flange Lock, GR B replaces NUT, 3/8-16 Hex Nyloc SEAL, Nylos see Footnote WASHER Footnotes: Note 1: (Spindle Hsg. Sub-Assy) is made of one Item 11 & 12 & six Items 13. NOTE 2: To install Bearing Pre-Seal Kit ( ) discard item 3 & replace with items 17 & 18 as shown. SERIES 0 & 1 43

44 DECALS (Pt. 1) 44 SERIES 0 & 1

45 DECALS (Pt. 1) Item Part No Qty Description Note DECAL, Console (Pistol Grip, Gear) DECAL, Console (Pistol Grip, Gear) (not shown; Similar to 73598) DECAL, SNAPPER Pro w/trademark (13.19 long) DECAL, SNAPPER Pro (8 long) DECAL, SNAPPER Pro (16.7 long) appearance is similar to item DECAL, Pro Express DECAL, 36 Deck (white numbers) DECAL, 36 Deck (silver numbers) DECAL, 48 Deck (white numbers) DECAL, 48 Deck (silver numbers) DECAL, Caution- Operator Instruction DECAL, Warning DECAL, Caution (Open Drive Belt) DECAL, SNAPPER (7.31 long) DECAL, SNAPPER (8 long; not shown) Footnotes: SERIES 0 & 1 45

46 DECALS (Pt. 2) 46 SERIES 0 & 1

47 DECALS (Pt. 2) Item Part No Qty Description Note DECAL, Operation (Gear Drive) DECAL, Warning (CPSC Cut Finger) DECAL, Shift DECAL, Caution, Counterweight (36 ) DECAL, Caution, Counterweight (48 ) DECAL, Warning, Counterweight DECAL, Throttle Control DECAL, PTO Switch DECAL, Ear Protection DECAL, Ignition Switch DECAL, Caution, Guard, Catcher DECAL, Right Hand Control Footnotes: SERIES 0 & 1 47

48 ELECTRICAL COMPONENTS (Pistol Grip Handle) 48 SERIES 0 & 1

49 ELECTRICAL COMPONENTS (Pistol Grip Handle) Item Part No Qty Description Note WIRING HARNESS, Pistol Grip Handle see also Pistol Grip Handle & Control Assemblies page Footnotes: SERIES 0 & 1 49

50 ELECTRICAL COMPONENTS (Loop Handle) 50 SERIES 0 & 1

51 ELECTRICAL COMPONENTS (Loop Handle) Item Part No Qty Description Note WIRING HARNESS, Loop Handle Footnotes: SERIES 0 & 1 51

52 WIRING SCHEMATIC (Pistol Grip Handle) 52 SERIES 0 & 1

53 WIRING SCHEMATIC (Pistol Grip Handle) Item Part No Qty Description Note WIRING SCHEMATIC (Pistol Grip Handle) Footnotes: SERIES 0 & 1 53

54 WIRING SCHEMATIC (Loop Handle) 54 SERIES 0 & 1

55 WIRING SCHEMATIC (Loop Handle) Item Part No Qty Description Note WIRING SCHEMATIC (Pistol Grip Handle) Footnotes: SERIES 0 & 1 55

Parts Manual for MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.

58 Parts Manual for MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. McDonough, GA, U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 6, 10/21/2005

Parts Manual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 POWER UNIT MODEL SPE1250KW SPE140KW SPE150KH SPE151KW SPEL150KH

Parts Manual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND MOWERS SERIES 0 & 1 POWER UNIT MODEL SPE10KW SPE0KW SPE10KH SPE11KW SPEL10KH MOWER UNIT MODEL SPE30 SPE480 SPE31 SPE481 IT IS POLICY OF SNAPPER TO