SCRAMBLER 33" & 38" HYDRO DRIVE YZ SERIES 5 & 6

Transcription

1 Parts Manual for SERIES 5 & 6 MODEL YZ16335BVE YZ16385BVE YZ18336BVE YZ18386BVE McDonough, GA, U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 3, 7/26/2005

2

3 Table Of Contents PAGE GROUP 4 CASTER, FRONT WHEEL & TIRE ASSEMBLY 6 WHEELS- REAR 8 FRONT FRAME & COVER ASSEMBLY 10 REAR FRAME ASSEMBLY 14 JOYSTICK & OPERATOR SEAT (Part 1) 16 JOYSTICK & OPERATOR SEAT (Part 2) 18 FENDER & TRANSAXLE ASSEMBLY 22 BRAKE/CLUTCH LEVER ASSEMBLY 24 ENGINE COMPONENTS 26 CLUTCH ASSEMBLY 28 DECK LIFT HANDLE ASSEMBLY 30 33" MOWER DECK ASSEMBLY (Part 1) 32 33" MOWER DECK ASSEMBLY (Part 2) 34 33" MOWER DECK ASSEMBLY (Part 3) 36 38" MOWER DECK ASSEMBLY (Part 1) 38 38" MOWER DECK ASSEMBLY (Part 2) 40 38" MOWER DECK ASSEMBLY (Part 3) 42 33" SPINDLE ASSEMBLY 44 38" SPINDLE ASSEMBLY 46 DECALS (Part 1) 48 DECALS (Part 2) 50 ELECTRICAL COMPONENTS 52 WIRING SCHEMATIC SERIES 5 & 6 3

4 CASTER, FRONT WHEEL & TIRE ASSEMBLY 4 SERIES 5 & 6

5 CASTER, FRONT WHEEL & TIRE ASSEMBLY Item Part No Qty Description Note ASSEMBLY, Front Wheel & Tire (Complete) (Includes Items 2 thru 5) TIRE, 11 x , Smooth Tread per front wheel & tire assembly RIM, 5.00 Dia. x 3.00 per front wheel & tire assembly LUBE FITTING, 1/4-28 Thread Forming Was 29275, per front wheel & tire assembly VALVE STEM, Air (Snap-in) per front wheel & tire assembly RING, 1 External Retaining BUSHING, Caster Was LUBE FITTING, Straight (press-fit for.187 dia. Hole) WELDMENT, Pivot Yoke, Caster NUT, 7/16-14 Hex Center Lock, GR5 or B TUBE, 5/8 O.D. x 14 Ga x BEARING, Ball, 5/8 x 1-3/ SCREW, 7/16-14 x 6 Hex Head Cap, GR5 Footnotes: SERIES 5 & 6 5

6 WHEELS- REAR 6 SERIES 5 & 6

7 WHEELS- REAR Item Part No Qty Description Note ASSEMBLY, Rear Tire & Rim (Includes items 2A, 3A & 7) used on 33 Deck Models ASSEMBLY, Rear Tire & Rim (Includes items 2B, 3B & 7) used on 38 Deck Models 2A TIRE, 18 x , Multi-Trac per rear wheel & tire assembly 2B TIRE, 18 x , Multi-Trac per rear wheel & tire assembly 3A RIM, 18 x 7.00 Wheel w/25mm Hub I. D. per rear wheel & tire assembly 3B RIM, 18 x 8.50 w/25mm Hub per rear wheel & tire assembly WASHER, 1.56 x x.047 Flat KLIPRING, 1 External (Waldes Truarc ) HUB CAP VALVE STEM, Air (Snap-in) per rear wheel & tire assembly KEY, Square M6 x 38mm Footnotes: SERIES 5 & 6 7

8 FRONT FRAME & COVER ASSEMBLY 8 SERIES 5 & 6

9 FRONT FRAME & COVER ASSEMBLY Item Part No Qty Description Note WELDMENT, Front Frame Series # PLATE, Footrest Support BOLT, 5/16-18 x 3/4 Hex Flange Lock NUT, 5/16-18 Hex Flange Lock, GR5 Was FASTENER, U Type SCREW, 3/8-16 x 1 Hex Washer Self-tap WASHER, 3/8 FLAT (wide) SPACER, Front Frame Pivot PLATE, Front Frame Slip FLOOR PAN, HOZ FOOTREST, HOZ WASHER, 1/4 Internal/External Lock KNOB (1/4-20 thread) MAT, Floor PAD, Floor Board Support DECAL, Warning, Read Manuals & Instructions see decal page DECAL, Deck Height see decal page DECAL, SNAPPER (14.56 long) Footnotes: SERIES 5 & 6 9

10 REAR FRAME ASSEMBLY 10 SERIES 5 & 6

11 REAR FRAME ASSEMBLY Item Part No Qty Description Note WELDMENT, Rear Frame CUSHION, Seat Support SPRING, Seat Support SCREW, 1/4-20 x 5/8 Pan Head Self-Tap (Torx) BOLT, 5/16-18 x 1/2 Short Neck Carriage, GR5 Was HINGE, Seat NUT, 5/16-18 Hex Flange Lock, GR5 Was BUMPER, Rear SCREW, 5/16-18 x 1-1/2 Hex Washer Self-Tap WASHER,.531 x x.121 SAE Flat NUT, 1/2-13 Hex Center Lock, GR5 or B WELDMENT, Battery Bracket BUSHING, Tie Rod SCREW, 5/16-24 x 1 Hex Head Cap, GR RETAINER, 5/16 Bolt WASHER,.32 x.58 x.08 Split Lock NUT, 5/16-24 Hex, GR5 or B GROMMET ASSEMBLY, Brake/Clutch Cable BOLT, 1/2-13 Hex Shoulder WELDMENT, Idler Arm, Primary SPRING, Extension- 5 long WASHER, 3/8 SAE Flat NUT, 3/8-16 Hex Center Lock, GR5 or B PULLEY,Idler, V 3.30 HA BOLT, 3/8-16 x 4 Hex Head Cap, GR BRACKET, Hydro Idler SPRING, Extension, Hydro Idler SCREW, 3/8-16 x 1-3/4 Hex Head Cap, GR CABLE, Hydro Release Valve SCREW, #10-32 x 5/8 Hex Washer Head Machine IDLER, 4.12 Outside Diameter, Flat NUT, #10-32 Hex Nyloc SWITCH, Seat (NO/NC) Snap-In also shown on electronic components page SLEEVE, Idler GUIDE, Belt COVER-Spring Footnotes: SERIES 5 & 6 11

12 REAR FRAME ASSEMBLY 12 SERIES 5 & 6

13 REAR FRAME ASSEMBLY Item Part No Qty Description Note FASTENER, Ratchet BUSHING, Flange,.64 x.75 x.5 Footnotes: SERIES 5 & 6 13

14 JOYSTICK & OPERATOR SEAT (Part 1) 14 SERIES 5 & 6

15 JOYSTICK & OPERATOR SEAT (Part 1) Item Part No Qty Description Note BRACKET, R.H. Tank Support WELDMENT, Bracket, Joystick PIVOT, Joystick Control WELDMENT, Handle, Joystick Control BOLT, 5/16-18 Shoulder, w/nylon Patch LEVER, Shift Handle (grip) ROLL PIN, 3/16 x 3/ ASSEMBLY, R.H. Fender BRACKET, R.H. Console BOOT, Joystick, Rubber BRACKET, Joystick Boot STOP, Joystick SCREW, 1/4-20 x 5/8 Pan Head Self-Tap (Torx) DECAL, Ignition Switch see decal page DECAL, SNAPPER DECAL, SCRAMBLER PIN, 3/8 Self Locking Cotter WASHER,.34 x.69 x.08 Flat CYLINDER, Joystick Control WELDMENT, U-Bracket PUSHNUT, 1/ PIN, Joystick NUT, 5/16-18 Hex, GR5 or B WASHER,.32 x.58 x.08 Split Lock BOLT, 5/16-18 x.530 Shoulder ARM REST, HOZ SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR NUT, 5/16-18 Hex Nyloc FENDER, R.H. Lower SCREW, 5/16-18 x 1/2 Pan Head Self-Tap (Torx) SWITCH, Ignition(After-fire Solenoid) also shown on electronic components page SCREW, 1/4-20 x 5/8 Hex Washer Self-Tap Was WELDMENT, Fender Support SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap Footnotes: SERIES 5 & 6 15

16 JOYSTICK & OPERATOR SEAT (Part 2) 16 SERIES 5 & 6

17 JOYSTICK & OPERATOR SEAT (Part 2) Item Part No Qty Description Note SCREW, 1/4-20 x 5/8 Pan Head Self-Tap (Torx) DECAL, SNAPPER WASHER,.34 x.69 x.08 Flat ARM REST, HOZ SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR NUT, 5/16-18 Hex Nyloc SCREW, 5/16-18 x 1/2 Pan Head Self-Tap (Torx) SCREW, 1/4-20 x 5/8 Hex Washer Self-Tap Was SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap BRACKET, L.H. Tank Support BRACKET, Brake/Clutch Detent FENDER, L.H. Lower SWITCH, Park Brake (NC/NO) also shown on electronic components page SCREW, #10-24 x 1/2" Hex Washer Self-Tap (Torx) (Torx) 40A BRACKET, L.H. Console series 5 40B BRACKET, L.H. Console series SWITCH, PTO E.C. (Delta Part No ) also shown on electronic components page 42A CONTROL, Throttle/Choke, Dual Lever series 5 42B CONTROL, Throttle series 6 (not shown) WELDMENT, Fuel Tank Support ASSEMBLY, Fuel Tank/Left Hand Fender includes fuel cap (75748), grommet (12337), fitting (74835) & tube (75708) GAS CAP w/screw Vent FITTING, Dapco Dapco part number # GROMMET DIP TUBE DECAL, Hydro Release see decal page DECAL, Park Brake see decal page DECAL, Operating Instructions see decal page SEAT, Milsco High Back TETHER, Seat HEAT SHIELD, Engine SCREW, 5/16-18 x 1/2 Hex Washer Self-Tap LEVER, Throttle Control series RIVET, Plastic Snap series 6 Footnotes: SERIES 5 & 6 17

18 FENDER & TRANSAXLE ASSEMBLY 18 SERIES 5 & 6

19 FENDER & TRANSAXLE ASSEMBLY Item Part No Qty Description Note TRANSAXLE, Hydro Eaton Model X TRANSAXLE, Hydro w/o Manifold R.H. Eaton Model X KEY, #605 Woodruff SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap Was FAN, 6 O.D., 10 Blade PULLEY, Hydro Input RING, RR External Retaining V-BELT, HA Sect effective length Hydro Drive BRACKET, Support, Fender BRACKET, Support, Hydro SCREW, 1/4-20 x 5/8 Hex Washer Self-Tap Was FENDER, Rear Frame, Left Hand FENDER, Rear Frame, Right Hand BRACKET, Deck Support, Left Rear BRACKET, Deck Support, Right Rear SCREW, 5/16-18 x 3/4 Hex Washer Self-Tap Was SCREW, 3/8-16 x 1 Hex Washer Self-tap BRACKET, Control Cable, Hydro ROD END, #10-32 w/stud NUT, #10-32 Hex Center Lock CABLE, L.H. Hydraulic Control (45.5 long) CABLE, R.H. Hydraulic Control (35.5 long) BRACKET, Cable, Hydro Release Valve SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap BRACKET, Actuator, Hydro Release Valve BUSHING, Differential Link, Powdered Metal SCREW, 5/16-18 x 1 Hex Washer Self-Tap, GR ARM, Directional Control BOLT, 1/4-28 x 5/8 w/nyloc Patch, GR WASHER, 1/4 Belleville ARM, Brake WASHER, 3/8" Flat Was ROD, Brake, R.H ROD, Brake, L.H COTTER-PIN, 1/16" x 1.42" Self-Locking Was SWIVEL, Brake Link- PM Footnotes: SERIES 5 & 6 19

20 FENDER & TRANSAXLE ASSEMBLY 20 SERIES 5 & 6

21 FENDER & TRANSAXLE ASSEMBLY Item Part No Qty Description Note SPRING, Brake Compression NUT, 3/8-16 Hex Nyloc CABLE, Hydro Release Valve DECAL, Hydro Reservoir see decal page WASHER, #10, Internal Tooth Lock NUT, #10-32, Hex Footnotes: SERIES 5 & 6 21

22 BRAKE/CLUTCH LEVER ASSEMBLY 22 SERIES 5 & 6

23 BRAKE/CLUTCH LEVER ASSEMBLY Item Part No Qty Description Note GRIP, 5/16 x 2-1/2 Vinyl color: red (replaces 29383) GRIP, Brake/Clutch Handle ROD, Park Brake 36 arc radius (replaces & 58542) SPRING, Clutch/Brake Release ARM, Brake/Clutch Lever PIVOT, Brake/Clutch Lever SCREW, 1/4-20 x 3/8 Hex Washer Self-Tap Was TUBE, Clutch/Brake Lever arc radius (replaces 58541) BUSHING, Nylon ROD, Clutch/Brake ASSEMBLY, Foot Shaft Pivot weldment with grease fitting, PIN, 3/16 x 1-1/2 Roll ARM, Brake/Clutch WELDMENT, Brake/Clutch Arm NUT, 5/16-18 Hex Flange Lock, GR5 Was SCREW, 5/16-18 x 7/8 Pan Head Self-Tap (Torx) Footnotes: SERIES 5 & 6 23

24 ENGINE COMPONENTS 24 SERIES 5 & 6

25 ENGINE COMPONENTS Item Part No Qty Description Note ENGINE, 18 HP Briggs Intek Model 31H E1 (series 5) ENGINE, 18 HP Briggs Intek Model 31H E1 (series 6) KEY, 1/4 Square x GASKET, Exhaust ASSEMBLY, Oil Valve GUIDE, Engine Belt PLATE, Engine PULLEY, Engine series 5 (bottom pulley 4.25 O.D.) PULLEY, Engine series 6 (bottom pulley 4.75 O.D.) SCREW, 3/8-16 x 1 Hex Washer Self-tap engine mounting bolts WASHER, 7/16 Split Lock SCREW, 7/16-20 x 1-1/2 Hex Head Cap, GR WASHER,.468 x 1.38 x.25 Flat (special) HOSE CLAMP,.490 x.31 or BOLT, 5/16-18 x 4 Shoulder SCREW LOCK DEFLECTOR, Muffler ADAPTER, Muffler Briggs part no MUFFLER, 14.5HP B&S Engine Nelson part no D SCREW, #8-18 x 1/2 Hex Head Sheet Metal HEAT SHIELD, Muffler- 17HP B&S Intek series HEAT SHIELD, Muffler- B&S series HOSE, Fuel, 1/4 I.D. x 14 long VALVE, Fuel HOSE, Fuel, 12-1/2 long Was A CONTROL, Throttle/Choke, Dual Lever series 5 23B CONTROL, Throttle series SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap Was BOLT, 5/16-18 x 5/8 Hex Flange Lock, GR5 Was HARNESS CLIP (vinyl covered) HEAT SHIELD LEVER, Throttle Control series RIVET, Plastic Snap series SCREW, #10-32 x 5/8 Hex Washer Head Machine series NUT, #10-32 Hex Nyloc series 6 Footnotes: SERIES 5 & 6 25

26 CLUTCH ASSEMBLY 26 SERIES 5 & 6

27 CLUTCH ASSEMBLY Item Part No Qty Description Note BOLT, 7/16-20 x 8 Hex Head, GR WASHER,.468 I.D. x 1.50 O.D. x.188 Flat BEARING, 6305 w/snap Ring NUT, 5/16-18 Hex Flange Lock, GR5 Was V-BELT, 5L Sect. Cog, effective length Primary Drive (Dayco # ) PULLEY, Jackshaft SCREW, 1/4-20 x 1/2 Set w/patch SUPPORT, Jackshaft- TG BOLT, 5/16-18 x 3/4 Short Neck Carriage, GR JACKSHAFT KEY 1/4 Square x 1 qty. 1 on 38 units BRACKET, Anti-Rotation, Ogura used on 33 units CLUTCH, Electric Ogura MA-GT-SN11S (33 units) CLUTCH/BRAKE, Electric (Warner) (38 units) WASHER, 7/16 Split Lock NUT, 7/16-20 Hex, GR5 or B WIRE CLIP 7/16, Vinyl Covered 17A SPACER, Jackshaft 17B SPACER, Clutch (Ogura) Footnotes: SERIES 5 & 6 27

28 DECK LIFT HANDLE ASSEMBLY 28 SERIES 5 & 6

29 DECK LIFT HANDLE ASSEMBLY Item Part No Qty Description Note HANDLE, Deck Lift BRACKET, Pivot Support WELDMENT, Deck Lift Handle WASHER - Slipper SPRING, Torsion SCREW, 1/4-20 x 5/8 Hex Head Cap, GR NUT, 1/4-20 Hex Flange Lock Was BAR, Deck Lift WASHER, 3/8 SAE Flat HAIR PIN, 3/32 x 1-1/ PIN, 3/8 x 2 Clevis DETENT, Lift Handle SCREW, 5/16-18 x 3/4 Hex Head Cap, GR NUT, 5/16-18 Hex Flange Lock, GR5 Was DECAL, Deck Position PIN.38 x.5 Large Head Clevis PIN, 3/8 x 1-5/8 Clevis SPACER, Deck Lift PIN, 3/32 x 3/4 Cotter BOLT, 1/4-20 x 3/4 Short Neck Carriage, GR GRIP, Deck Lift Footnotes: SERIES 5 & 6 29

30 33" MOWER DECK ASSEMBLY (Part 1) 30 SERIES 5 & 6

31 33" MOWER DECK ASSEMBLY (Part 1) Item Part No Qty Description Note * DECK, 33 Replacement BRACKET, 33 Deck Lift, Slotted BRACKET, 33 Deck Lift BRACKET, Anti-Scalp, Front, Adjustment BRACKET, Anti-Scalp, Side, Adjustment WEIGHT BAR, 33 Rear, HOZ BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 replaces NUT, 3/4-16 Hex Jam, GR BOLT, 5/16-18 x 3/4 Hex Flange Lock NUT, 5/16-18 Hex Flange Lock Was BOLT, 5/16-18 Hex Flange Lock, GR SPACER,.340 I.D. x.63 O.D. x.310 thick NUT, 5/16-18 Hex Center Lock, GR B Was BOLT, 5/16-18 x 1/2 Short Neck Carriage, GR5 Was BRACE, Spindle BOLT, 3/8-16 x 3/4 Hex Flange Lock, GR5 Was or NUT, 3/8-16 Hex Flange Lock Was BLADE, 33 High Lift SCREW, 1/2-20 x 1-1/4 Hex Head Cap, GR5 replaces WASHER, 1/2 Internal Tooth Lock NUT, 1/2-20 Hex GR5 or B replaces ASSEMBLY, Spindle TOLERANCE RING, RING, 2 External Retaining WELDMENT, Idler Arm, WASHER, Spindle PULLEY, 33 Spindle WASHER,.781 x 1.5 x.132 Flat NUT, 3/8-16 Hex Center Lock Was Footnotes: SERIES 5 & 6 31

32 33" MOWER DECK ASSEMBLY (Part 2) 32 SERIES 5 & 6

33 33" MOWER DECK ASSEMBLY (Part 2) Item Part No Qty Description Note WASHER,.781 x 1.5 x.132 Flat NUT, 3/8-16 Hex Center Lock Was WELDMENT, Lift Arm, Front WASHER, 3/4 Flat ECCENTRIC, Leveling WASHER, 3/8 Internal Tooth Lock LIFT ARM, Front SCREW, 3/8-24 x 1-1/4 Hex Head Cap w/nylon Patch, GR WELDMENT, Lift Arm, Rear ROD, Cutter Deck Timing SWIVEL, Brake Link- PM SPACER,.391 I.D. x.531 long WASHER, 3/8 SAE Flat HAIR PIN, #13 Was ROD, Deck Support RING,.438 External Retaining Footnotes: SERIES 5 & 6 33

34 33" MOWER DECK ASSEMBLY (Part 3) 34 SERIES 5 & 6

35 33" MOWER DECK ASSEMBLY (Part 3) Item Part No Qty Description Note SCREW, 3/8-24 x 3-3/4 Hex Head Cap, GR SPACER, 3 long WHEEL, Gage ASSEMBLY, Discharge Chute includes items 48 thru SPRING, Hinge CHUTE, Discharge, 28 / ROD, Chute PALNUT WASHER (for.25 dia. rod) DECAL, Danger, Cut Finger (CPSC) replaces HINGE, Plastic Side Chute BOLT, 5/16-18 x 5/8 Hex Flange Lock, GR NUT, 5/16-18 Hex Flange Lock, GR IDLER, Flat (4.00 O.D.) replaces WASHER, 3/8" Flat Was NUT, 3/8-16 Hex Center Lock, GR5 or B SPRING, Extension 1.03 Dia. X 6.8 long BELT, HA Section, 33 DECK (55.2 effective length) DECAL, 33 Hi-Vac HAIR PIN, 3/32 x 1-1/ ADJUSTER, Chain (5/16-18 thread) SWIVEL, Adjustment BOLT, 5/16-18 x 3/4 Short Neck Carriage, GR WASHER, 11/32 Flat Was WING NUT, 5/16-18 Was WASHER,.375 x.875 x.083 Flat NUT, 3/8-24 Hex Center Lock replaces DECAL, Chute/Deflector Footnotes: SERIES 5 & 6 35

36 38" MOWER DECK ASSEMBLY (Part 1) 36 SERIES 5 & 6

37 38" MOWER DECK ASSEMBLY (Part 1) Item Part No Qty Description Note * DECK, 38 Replacement ASSEMBLY, Spindle- 38 Deck Was or PULLEY, 4.5 O.D., A/B Groove ASSEMBLY, Idler Arm, 38 Deck includes items 5 thru WELDMENT, Idler Arm Was BUSHING, 1/2 Nylon LUBE FITTING, Straight (press-fit for.187 dia. Hole) BRACKET, Gage Wheel BRACKET, Left Hand Wheel BRACKET, 38 Deck Lift, Left Front BRACKET, 38 Deck Lift, Right Front BOLT, 5/16-18 x 3/4 Hex Flange Lock replaces BRACKET, L.H., Rear Lift Arm NUT, 5/16-18 Hex Center Lock, GR5 or B NUT, 3/8-16 Hex Flange Lock Was NUT, 5/8-18 Hex Jam or BRACKET, Gage Wheel STUD, Idler (5/16-24 thread) WELDMENT, Stationary Idler NUT, 5/16-18 Hex Flange Lock Was BOLT, 5/16-18 x 5/8 Short Neck Carriage, GR5 Was NUT, 5/16-24 Hex Lock, GR C Was BOLT, 3/8-16 x 3/4 Short Neck Carriage Was or WASHER,.531 x x.121 SAE Flat PIN, 3/32 x 3/4 Cotter replaces BOLT, 5/16-18 x 1 Short Neck Carriage, GR5 replaces SPACER,.340 I.D. x.63 O.D. x.310 thick WASHER,.375 x.875 x.083 Flat WASHER, 5/16 x1-1/4 x.09 Flat Footnotes: SERIES 5 & 6 37

38 38" MOWER DECK ASSEMBLY (Part 2) 38 SERIES 5 & 6

39 38" MOWER DECK ASSEMBLY (Part 2) Item Part No Qty Description Note ECCENTRIC, Leveling LIFT ARM, Front WASHER, 3/8 Internal Tooth Lock SCREW, 3/8-24 x 1-1/4 Hex Head Cap w/nylon Patch, GR WELDMENT, Lift Arm, Front WASHER, 3/4 Flat ROD, Cutter Deck Timing (3/8-16 thread) WELDMENT, Lift Arm, Rear SWIVEL, Brake Link- PM HAIR PIN, #13 Was NUT, 3/8-16 Hex Center Lock Was WASHER,.781 x 1.5 x.132 Flat SPACER,.391 I.D. x.531 long WASHER,.375 x.875 x.083 Flat Footnotes: SERIES 5 & 6 39

40 38" MOWER DECK ASSEMBLY (Part 3) 40 SERIES 5 & 6

41 38" MOWER DECK ASSEMBLY (Part 3) Item Part No Qty Description Note NUT, 5/16-18 Hex Center Lock, GR5 or B NUT, 3/8-16 Hex Flange Lock Was WHEEL, 4 x 1-1/2 Offset BOLT, 3/8-24 x.62 Shoulder DECAL, Danger, Cut Finger (CPSC) replaces ROD, Deck Support RING,.438 External Retaining V-BELT, HA Section 89.8 Effective Length WASHER,.34 x.69 x.08 Flat replaces ADJUSTER, Chain (5/16-18 thread) SWIVEL, Adjustment HAIR PIN, 3/32 x 1-1/ WASHER, 3/8 SAE Flat replaces DECAL, 38 Inch DECAL, Chute/Deflector SPRING, Extension 1.03 Dia. X 6.8 long IDLER, 3-1/4 I.D. x 1-1/4 Flat PULLEY, 3-1/4 Dia. Flat Idler WASHER, Cone CHUTE, Discharge, 38 Deck ROD, Pivot, Side Discharge, BOLT, 5/16-18 x 3/4 Short Neck Carriage, GR ROD, Mounting, Side Discharge 3/8-16 thread SPRING, Torsion-Side Discharge-38 Deck TEENUT, 5/16-18 Thread SCREW, 3/8-16 x 1-3/4 Hex Head Cap, GR5 replaces NUT, 3/8-24 Hex Center Lock NUT, 3/8-16 Hex Center Lock, GR5 or B SCREW 5/16-18 x 5/8 Cross Recessed Pan Head Was Footnotes: SERIES 5 & 6 41

42 33" SPINDLE ASSEMBLY 42 SERIES 5 & 6

43 33" SPINDLE ASSEMBLY Item Part No Qty Description Note ASSEMBLY, Spindle includes items 1 thru WELDMENT, Spindle Housing SHAFT, Spindle (7.54 long) WASHER, Spindle BALL BEARING, 3/4 I.D HOLDER, Blade RING, 1-3/4 External Retaining Ring FITTING, Lube, Press-In (for.187 dia. Hole) NUT, 5/8-18 Hex Center Lock Jam, GR5 or B SCREW, 1/2-20 x 1 Hex Head Cap NUT, 1/2-20 Hex GR5 or B replaces Footnotes: SERIES 5 & 6 43

44 38" SPINDLE ASSEMBLY 44 SERIES 5 & 6

45 38" SPINDLE ASSEMBLY Item Part No Qty Description Note ASSEMBLY, Spindle- 38 Deck Was (Includes 2 thru 9) FITTING, Lube, Press-In (for.187 dia. Hole) RING, 1-3/4 External Retaining Ring BALL BEARING, 3/4 I.D WELDMENT, 38 Spindle Housing SHAFT, Spindle (7.155 long) WASHER, Spindle Blade WASHER, Bellville 9/16 x 1-3/ NUT, 9/16-18 Hex, GR B BLADE, Deck SPACER, Pulley Footnotes: SERIES 5 & 6 45

46 DECALS (Part 1) 46 SERIES 5 & 6

47 DECALS (Part 1) Item Part No Qty Description Note DECAL, SNAPPER DECAL, SCRAMBLER DECAL, Park Brake DECAL, Deck Height DECAL, Ignition Switch DECAL, Engine, 16 HP OHV B&S Simplicity part no DECAL, Hydro Reservoir DECAL, Deck Position DECAL, 33 Hi-Vac DECAL, 38 Inch Footnotes: SERIES 5 & 6 47

48 DECALS (Part 2) 48 SERIES 5 & 6

49 DECALS (Part 2) Item Part No Qty Description Note DECAL, Warning, Read Manuals & Instructions DECAL, Operating Instructions DECAL, Chute/Deflector DECAL, Danger, Cut Finger DECAL, Hydro Release DECAL, Service Parts, HOZ Domestic DECAL, Caution, Fuel (English) DECAL OPEI Ride-On Footnotes: SERIES 5 & 6 49

50 ELECTRICAL COMPONENTS 50 SERIES 5 & 6

51 ELECTRICAL COMPONENTS Item Part No Qty Description Note WIRING HARNESS, 18 HP Briggs NUT, 1/4-20 Hex Jam, GR5 or B SCREW, #10-24 x 1/2 Hex Head Cap NUT, 1/4-20 Hex Flange Lock WIRE, Positive, 13 long WIRE, Negative, 14 long COVER, Battery Cable WASHER, 1/4 Internal Tooth Lock Was SWITCH, Seat (NO/NC) Snap-In SWITCH, PTO E.C. Delta part no SWITCH, Park Brake (NC/NO) SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx) BATTERY, 12V, 3 Amp, 190 Cold Cranking Amp includes drain tube SWITCH, Ignition (After-fire Solenoid) SPACER,.65 x.88 x.10 - YZ BEZEL SOLENOID - Super Trombetta- 2 Terminal SCREW, 1/4-20 x 1/2 Hex Head Cap, GR NUT, #10-24 Hex Twin Whiz Lock SPACER, PTO Switch not shown Footnotes: SERIES 5 & 6 51

52 WIRING SCHEMATIC 52 SERIES 5 & 6

53 WIRING SCHEMATIC Item Part No Qty Description Note Wiring schematic includes harness # Footnotes: SERIES 5 & 6 53

54

55

56 Parts Manual for SERIES 5 & 6 IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. McDonough, GA, U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 3, 7/26/2005