Parts Manual. Coronet / 2400 Series Riders & Mower Decks RMO. 13HP Product. 16HP Product. Mower Decks

Transcription

1 Parts Manual 13HP Product Mfg. No. Description Coronet, 13HP Hydro RMO Coronet / 2400 Series Riders & Mower Decks RMO Coronet, 13HP Hydro RMO (CE) H, 13HP Hydro RMO H, 13HP Hydro RMO (CE) Coronet, 13HP Hydro RMO and 30" Mower Deck Coronet, 13HP Hydro RMO and 30" Mower Deck (CE) H, 13HP Hydro RMO and 30" Mower Deck H, 13HP Hydro RMO and 30" Mower Deck (CE) 16HP Product Mfg. No. Description Coronet, 16HP Hydro RMO Coronet, 16HP Hydro RMO and 34" Mower Deck Mower Decks Mfg. No. Description " Mower Deck " Mower Deck " Mower Deck (CE) " Mower Deck " Mower Deck Part No.: Rev. 11/2005

2

3 Table Of Contents PRODUCT COMPONENTS PAGES Frame & Fuel System Group... 4 Steering & Lift Group... 8 Engine & Electric Clutch Group - 13HP Briggs & Stratton Models Engine & Electric Clutch Group - 16HP Kohler Models Transmission Group - Hydro-Gear Transmission SERVICE PARTS - Hydro-Gear Electrical Group Electrical Group Front Column & Dash Group Wheels & Tires Group Decals Group - Brand & Model Decals Group - Common & Safety " Mower Deck - Drive & Arbor " Mower Deck - Housing & Height Adjustment (CE) " Mower Deck - Housing, Hitch & Height Adjustment " Mower Deck - Drive & Arbor " Mower Deck - Height Adjustment " Mower Deck - Housing, Hitch & Deflector Torque Specification Chart... Inside Back Cover

4 Frame & Fuel System Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

5 Frame & Fuel System Group REF NO PART NO. QTY. DESCRIPTION CAPSCREW, Hex Head, 5/16-18 x CAPSCREW, Hex Head, Taptite, 1/4-20 x 1/ A 1 SHROUD, Rear NUT, Hex, Flange, Whizlock, 5/ A 1 SUPPORT, Fuel Tank CARRIAGE BOLT, 5/16-18 x 3/ A 1 STRAP, Fuel Tank, Brace CAP, Fuel Tank, Vented TANK, Fuel SPACER, 21/64 x 1/2 x 21/ WASHER, Plain, 13/32 x 7/8 x 5/ CAPSCREW, Taptite, 5/16-18 x 1-1/ (16HP Models) CAPSCREW, Hex, Taptite, 5/16-18 x 1 (13 HP Models) BUSHING, Rubber ELBOW CLAMP, Hose HOSE, Fuel Line WASHER, Plain PUSH NUT, 5/ CAPSCREW, Hex Head, Whizlock, 5/16-18 x 3/ PAD, Foot Rest, LH FRAME ASSEMBLY PAD, Foot Rest, RH FASTENER A 1 PANEL, Front PAL NUT, 5/ A 1 SUPPORT, "U", Seat (16 HP Models) A 1 SUPPORT, "U", Seat (13 HP Models) BUMPER, Rubber CAPSCREW, Hex Head, Taptite, 5/16 x 1/ A 1 DUCT, Air Inlet (13 HP Models) A 1 DUCT, Air Inlet (16 HP Models) SPACER, Plastic SPACER PIN, Quick PIVOT, Hood WASHER CAPSCREW, Hex Head, 5/16-18 x 1-1/ NUT, Hex, 5/ CAPSCREW, 5/16-18 x 1-1/ SPACER WASHER, 1" CAP, Black, Vinyl Footnotes 5

6 Frame & Fuel System Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

7 Frame & Fuel System Group REF NO PART NO. QTY. DESCRIPTION A 1 ADJUSTER, Seat SPRING, Extension A 1 SUPPORT, Seat SPACER SEAT ASSEMBLY DECK, Seat, Orange Simplicity DECK, Seat, Red DECK, Seat, Orange Agco Allis RIVET SCREEN, Seat Deck Top CAPSCREW, Hex Head, Whizlock, 1/4-20 x 5/ NUT, Hex, Flange Lock, 1/ WASHER, 5/ SCREW, Truss Head, 1/4-20 x 3/ CAPSCREW, Hex Head, 5/16-18 x 1-3/4 (16 HP Models) A 1 PLATE, Control SCREEN Footnotes 7

8 Steering & Lift Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart SL 8

9 Steering & Lift Group REF NO PART NO. QTY. DESCRIPTION NUT, Hex, 3/ PIVOT A 1 ARM ASSEMBLY, Lift GRIP, Lever A 1 LEVER, Lift SPRING, Compression WASHER, Plain, 13/32 x 7/8 x 5/ COTTER PIN, 3/32 x 3/ CABLE ASSEMBLY, Lift NUT, Hex, Esna Lock, 3/ PULLEY, Lift SPACER WASHER, Plain, 13/32 x 1-1/2 x 1/ CAPSCREW, Hex Head, 3/8-16 x 1-1/ NUT, Hex, Flange Lock, 3/ ECCENTRIC WASHER, 13/32 x 7/8 x 1/ CAPSCREW, Hex Head, 3/8-16 x 1-3/ SPINDLE ASSEMBLY, LH NUT, Hex, Flange Lock, 5/ SPACER KLIP RING CARRIAGE BOLT, 5/16-18 x A 1 TIE ROD, LH WASHER SPACER, 21/64 x 1/2 x 5/ WASHER A 1 LEVER ROD, Hitch CAPSCREW, Hex Head, 1/2-13 x 1-1/ A 1 HITCH, Hook SPACER NUT, Hex, Flange Lock, 1/ SPINDLE ASSEMBLY, RH A 1 TIE ROD, RH Footnotes 9

10 Engine & Electric Clutch Group - 13HP Briggs & Stratton Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart Dual Control Single Control 10

11 Engine & Electric Clutch Group - 13HP Briggs & Stratton Models REF NO PART NO. QTY. DESCRIPTION SCREW, Thread Forming, #10-16 x 1/ WASHER, LOCKWASHER, 5/ NUT, Hex, 5/ CAPSCREW, Hex Head, Taptite, 5/16-18 x 1/ DUCT, R.H., Top SCREW, Taptite, 1/4-20 x SEAL, Air Inlet NUT, Flange, Whizlock, 5/ VALVE, Shut-Off WASHER, Plain EDGING, Seal WASHER, 3/ CAPSCREW, Taptite, 3/8-16 x PUSH NUT, 5/ CAPSCREW, Hex, Whizlock, Flange, 5/16-18 x 1-1/ SLEEVE, Clutch Anchor CLUTCH, Electric, Kit CAPSCREW, Hex Head, 7/16-20 x 2-1/ LOCKWASHER, 7/ CAPSCREW, Taptite, 3/8-16 x 1-1/ GASKET, Muffler PIPE, Exhaust CAPSCREW, Socket Head, 5/16-18 x 3/ CARRIAGE BOLT, 5/16-18 x 3-1/ A 1 CLAMP, Muffler A 1 SUPPORT, Muffler SPEED NUT, 5/ MUFFLER ASSEMBLY A 1 DUCT, Bottom THROTTLE CONTROL, Duel (Export Only) THROTTLE CONTROL, Single 39 * 1 ENGINE, Briggs & Straton, 13HP, Model 21A907, Type 0131-E1 Footnotes Note* See your local Briggs & Stratton distributor for parts & service. 11

12 Engine & Electric Clutch Group - 16HP Kohler Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart

13 Engine & Electric Clutch Group - 16HP Kohler Models REF NO PART NO. QTY. DESCRIPTION SCREW, Thread Forming, #10-16 x 1/ WASHER, LOCKWASHER, 5/ NUT, Hex, 5/ CAPSCREW, Hex Head, Taptite, 5/16-18 x 1/ A 1 DUCT, R.H., Top SEAL, Air Inlet VALVE, Shut-Off WASHER, Plain CAPSCREW, Taptite, 3/8-16 x CAPSCREW, Hex, Whizlock, Flange, 5/16-18 x 1-1/ SLEEVE, Clutch Anchor CLUTCH, Electric, Kit CAPSCREW, Hex Head, 7/16-20 x 2-1/ LOCKWASHER, 7/ CAPSCREW, Taptite, 3/8-16 x 1-1/ PIPE, Exhaust CARRIAGE BOLT, 5/16-18 x 3-1/ A 1 CLAMP, Muffler A 1 SUPPORT, Muffler SPEED NUT, 5/ MUFFLER ASSEMBLY A 1 DUCT, Bottom THROTTLE CONTROL, Single 39 * 1 ENGINE, Kohler, 16HP, Model CV460S, Type PA Footnotes Note* See your local Briggs & Stratton distributor for parts & service. 13

14 Transmission Group - Hydro-Gear NOTE: Unless noted otherwise, use the standard hardware torque specification chart

15 Transmission Group - Hydro-Gear REF NO Footnotes PART NO. QTY. DESCRIPTION PAD, Brake A 1 LEVER, Clutch PIVOT, Brake RING, Klipring Extension KEY, Hi-Pro STOP, Belt PULLEY & HUB ASSEMBLY, Engine V - BELT BUSHING WASHER, 1/ RING, Klipring Extension CARRIAGE BOLT, 5/16-18 x 2-1/4 G BRACKET, Torsion Bar SCREW, Hex, Washer Head, Taptite, 5/16-18 x 1/ SPRING, Extension SPACER NUT, Hex, Flange, 1/4-20, Whiz Lock LG A 1 PLATE, Idler 10GA CLEVIS HALF WASHER, 5/ WASHER, 5/ LOCKWASHER, Spring 5/ NUT, Hex 5/ CAPSCREW, Hex Head, 1/4-20 x 3/4 G SCREW, Hex, Washer Head, Taptite, 1/4-20 x 5/ NUT, Hex Flange,, 3/8-16 Whiz Lock LG NUT, Hex, Toplock, Jam, 3/ SPRING, Extension CAPSCREW, Hex Head, 3/8-16 x 3-1/4 G PULLEY A 1 GUARD, Spring SPACER NUT, Hex Flange,, 1/2-13, Two-Way Lock WASHER, 1/ SPACER CAPSCREW, Hex Head, 1/2-20 x 1-3/4 G CAPSCREW, Hex Head, 1/2-13 x 1 G SPACER CARRIAGE BOLT, 5/16-18 x 5/8 G A 1 CARRIER ASSEMBLY A 1 BRACKET, Switch Mounting (No-Mow Models Only) CARRIAGE BOLT, 1/4-20 x 5/8 G5 (No-Mow Models Only) NUT, Hex Flange, 5/16-18, Whiz Lock Small A 1 STRAP, Torque (No-Mow Models Only) 15

16 Transmission Group - Hydro-Gear NOTE: Unless noted otherwise, use the standard hardware torque specification chart

17 Transmission Group - Hydro-Gear REF NO PART NO. QTY. DESCRIPTION STRAP, Torque NUT, Hex Flange, 1/4-20 ESNA (No-Mow Models Only) ROD CAPSCREW, Hex Head, 5/16-18 x 2-1/2 G A 2 BRACKET, Mounting SCREW, Hex, Washer Head, Taptite, 5/16-18 x 3/ NUT, Hex Machine Screw SPRING, Extension NUT, Hex Flange, 5/16-18, Two-Way Lock SPRING ROD, Brake CAPSCREW, Hex Head, 3/8-16 x 1 G JOINT, Ball A 1 LEVER, Control NUT, Hex Flange, 3/8-16, Two-Way Lock CAPSCREW, Hex Head, 5/16-18 x 5/8 G ROD, Control PIN, Quick PIN, Cotter SCREW, Hex, Whiz Lock, Flange, 3/8-16 x 1-3/ SPACER FITTING, Lube, 1/4 Drive SHAFT & ARMS ASSEMBLY, Pivot CLUTCH, Rear BAR, Torsion TUBE ROD, Shift, Front WASHER, 1/ ROD, Clutch, Front TRANSMISSION ASSEMBLY, Hydro Gear Footnotes 17

18 Transmission SERVICE PARTS - Hydro-Gear NOTE: Unless noted otherwise, use the standard hardware torque specification chart

19 Transmission SERVICE PARTS - Hydro-Gear REF NO PART NO. QTY. DESCRIPTION 1 * 1 MAIN HOUSING, ASSEMBLY 2 * 1 SIDE HOUSING, ASSEMBLY 3 * 1 CENTER SECTION, ASSEMBLY 4 * 1 SWASHPLATE, TRUNNION MACHINED 5 * 2 BLOCK - ASSEMBLY 6 * 10.5 SEALANT (Not Shown) HEX FLANGE SCREW 1/4-20 X STUD, 5/16-24 HEX DOUBLE END SHAFT, INPUT RING - RETAINING SPACER RING - RETAINING 13 ** 1 SEAL, LIP.67 X 1.58 X BALL BRG 17MM ID X 40MM OD X 12MM HEX FLANGE HEAD SCREW 5/16-24 X ** 1 LIP SEAL 18 X 32 X ARM, CONTROL 19 * 1 BEARING, 30X52X13 THRUST 24 * 1 SHAFT, MOTOR 27 * 1 GEAR - PINNION, 13T 28 * 1 10T/48T GEAR 29 * 1 GEAR, 10T JACKSHAFT 30 * 1 60T BULL GEAR 31 * 2 SLEEVE BEARING.75 X X SLEEVE BEARING (OUTBOARD).75 X X * 2 WASHER, 3/4 ID X 1-1/2 OD X.13 THK 34 ** 2 LIP SEAL AXLE SEAL SHAFT, AXLE.75 x (KEY, R.H.) SHAFT, AXLE.75 X (KEY, L.H.) 37 * 2 MITER GEAR (SPLINED) 38 * 2 MITER GEAR 15T (0.5 ID) 39 * 1 SHAFT 40 * 2 RING, SPIRAL RETAINING 41 * 1 PIN, JACKSHAFT 42 * 1 MAGNET, RING 43 * 1 SPRING, BYPASS 44 * 2 BOLT, HEX FLANGE 3/8-24 X * 1 BOTTOM, FILTER 46 * 1 BASE, FILTER W/POPPET 47 * 1 ACTUATOR, BYPASS 48 * 1 ROD, BYPASS ACTUATOR ARM, BYPASS RETAINING RING.250 EXTERNAL 51 ** 1 SEAL, LIP.741 X.250 x.250 TC Footnotes Note* Not serviced seperately, order complete transmission. Note** Not serviced seperately, order seal kit reference # 126,

20 Transmission SERVICE PARTS - Hydro-Gear NOTE: Unless noted otherwise, use the standard hardware torque specification chart

21 Transmission SERVICE PARTS - Hydro-Gear REF NO PART NO. QTY. DESCRIPTION 52 * 1 FLAT WASHER, 5/8 ID X 1.0 OD X.05 THK 53 * 1 RETAINING RING 54 * 1 BEARING, CENTER BLOCK SPRING - HELICAL COMPRESSION WASHER W-50 OIL (Not Shown) BRAKE YOKE ROTOR, BRAKE BRAKE PUCK PUCK PLATE BRAKE ACTUATING PIN HFHCS 1/4-20 X 2 W/PATCH SPACER SPRING, BRAKE ARM BIAS SQ.HD.BOLT 5/ RIBBED ARM, BRAKE SLOTTED HEX NUT 5/ COTTER PIN 3/32 X 3/ SPRING, COMPRESSION 72 * 2 WASHER, HT.5 X 1 X FLAT - WASHER 11/32 I.D. X 7/8 O.D 74 ** 1 OIL SEAL.625 X 1.0 X * 2 CHECK PLUG ASSEMBLY,.027, WASHER STUD, 5/16-24 FRICTION PACK PUCK,.330 X 1.50 X SPRING, HELICAL COMP SPACER HEX LOCK NUT 5/16-24 UNJF WEDGE, FRICTION PACK WASHER.316 X 1.50 X.1046 (PLATED) 83 * 2 PIN, STANDARD HEADLESS 84 * 1 FITTING, 5/16 SAE 5/32 TUBE HOSE, EXPANSION TANK CAP, VENT BOLT, SELF TAPPING X 1/ PUCK, INNER WEDGE SPRING CLIP - HOUSING THRUST 107 * 1 DEFLECTOR 108 * 1 WASHER,.71 X 1.16 X.030 THK PLUG, SAE #6 111 ** 1 O-RING.07 X.301 ID BRACKET,SUPPORT EXPANSION TANK SILICON SPONGE FAN 6" 10 BLADE PULLEY 3.86 Footnotes Note* Not serviced seperately, order complete transmission. Note** Not serviced seperately, order seal kit reference # 126,

22 Transmission SERVICE PARTS - Hydro-Gear NOTE: Unless noted otherwise, use the standard hardware torque specification chart

23 Transmission SERVICE PARTS - Hydro-Gear REF NO PART NO. QTY. DESCRIPTION NUT, HEX LOCK 1/2-20 (NYLON INSERT) WASHER, OD SLOTTED.53 X 1.63 X BELT KEEPER 124 * 1 CENTER SECTION - FILTER - BYPASS ASSEMBLY (Incl Ref No 3, 43, 45, 46, 47, 75 & 107) 125 * 1 FILTER ASSEMBLY (Incl Ref No 43, 45, 46, 47 & 107) KIT, FAN/PULLEY (Incl Ref No 13, 17, 34, 51, 74 & 111) SEAL - O-RING KIT (Incl Ref No 13, 17, 34, 51, 74 & 111) KIT, EXPANSION TANK (Incl Ref No 87, 88, 113 & 116) CAP, EXPANSION TANK SHIPPING Footnotes Note* Not serviced seperately, order complete transmission. Note** Not serviced seperately, order seal kit reference # 126,

24 Electrical Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

25 Electrical Group REF NO PART NO. QTY. DESCRIPTION CABLE, Battery to Ground WASHER, Lock, 1/ NUT, Hex 1/ BOOT, Insulator CABLE, Battery to Solenoid BATTERY STRAP, Battery NO-MOW MODULE (RMO Models Only) BRACE, Battery CAPSCREW, Hex Head, 1/4-20 x 3/ WASHER WIRE ASSEMBLY, 16GA SWITCH, Neutral Start POP-RIVET SWITCH, Push Button (N.O.) (RMO Models Only) TIE, Self-Locking SOLENOID CAPSCREW, Hex Head, Taptite, 1/4-20 x 1/ CIRCUIT BREAKER WIRE ASSEMBLY LOCKWASHER, 5/ COVER, Terminal NUT, Hex, 5/ CABLE, Solenoid to Starter 25 ** 1 SWITCH, Ignition (6 pole) WASHER, Internal Tooth, 5/ NUT COVER, Keyswitch KEYS (Set of 2 Keys) SWITCH, Seat * SWITCH, PTO, Electric Clutch WIRE HARNESS, Clutch (RMO Models Only) WIRE HARNESS, Clutch HARNESS, Wiring (RMO Models Only) HARNESS, Wiring IGNITION KEY SWITCH ASSEMBLY Footnotes Note* If connection blades do not line up use Switch Kit. (Contains switch, adaptor & instruction sheet.) Note** See reference number 41. Sold as assembly. 25

26 Electrical Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

27 Electrical Group REF NO PART NO. QTY. DESCRIPTION CABLE, Battery to Ground WASHER, Lock, 1/ NUT, Hex 1/ BOOT, Insulator CABLE, Battery to Solenoid BATTERY STRAP, Battery BRACE, Battery CAPSCREW, Hex Head, 1/4-20 x 3/ WASHER WASHER, Lock, External Tooth, 3/ NUT, Hex, 3/ NO-MOW MODULE WIRE ASSEMBLY, Harness to Engine (Briggs & Stratton Only) SWITCH, Neutral Start POP-RIVET SWITCH, Push Button (N.O.) TIE, Self-Locking SOLENOID CAPSCREW, Hex Head, Taptite, 1/4-20 x 1/ CIRCUIT BREAKER WIRE ASSEMBLY LOCKWASHER, 5/ COVER, Terminal NUT, Hex, 5/ CABLE, Solenoid to Starter 27 ** 1 SWITCH, Ignition (6 pole) WASHER, Internal Tooth, 5/ NUT COVER, Keyswitch KEYS (Set of 2 Keys) SWITCH, Seat * SWITCH, PTO, Electric Clutch WIRE HARNESS, Clutch HARNESS, Wiring IGNITION KEY SWITCH ASSEMBLY Footnotes Note* If connection blades do not line up use Switch Kit. (Contains switch, adaptor & instruction sheet.) Note** See reference number 41. Sold as assembly. 27

28 Front Column & Dash Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart ,

29 Front Column & Dash Group REF NO Footnotes PART NO. QTY. DESCRIPTION STEERING WHEEL ASSEMBLY (Includes Ref. No. 49) ROLL PIN TUBE, Steering PIN WASHER, 49/ BUSHING TUBE ASSEMBLY, Shift WASHER BUSHING WASHER, Plain, 17/32 x 1-1/4 x 7/ SPRING, Torsion COTTER PIN ROD, Shift KNOB, Rod, Shift WASHER, Plain, 11/32 x 1 x 1/ SHAFT ASSEMBLY, Steering WASHER, Plain CARRIAGE BOLT, 3/8-16 x A 1 PLATE, Steering Mounting NUT, Hex, 3/ CAPSCREW, Hex Head, 5/16-18 x 1-1/ NUT, Hex, Flange Lock, 3/ WASHER, 13/32 x 1-1/2 x 1/ GEAR, Steering SPACER CAPSCREW, Hex Head, 3/8-16 x DASH, Hydro DASH, Gear CAPSCREW, Hex, Flange, Taptite, 1/4-20 x 3/ KNOB, Rod, Parking Brake ROD, Parking Brake PUSH NUT, 5/ NUT, Hex, Flange, Whizlock, 5/ QUADRANT, Lift CAPSCREW, Hex Head, Taptite, 1/4-20 x 1/ CLAMP WASHER, Plain, 1/ CAPSCREW, Hex Head, 1/4-20 x 7/ NUT, Hex, Flange Centerlock, 1/ SPACER, 17/64 x 3/8 x 21/ CAPSCREW, Hex Head, Whizlock, 5/16-18 x 3/ A 1 SUPPORT, Steering C 1 SHROUD, Front (Orange) D 1 SHROUD, Front (Red) 29

30 Front Column & Dash Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart ,

31 Front Column & Dash Group REF NO PART NO. QTY. DESCRIPTION PAL NUT, 5/ ROD, Lift Height NUT, Hex, Jam, 1/ KNOB, Rod, Lift Height NUT, Hex, Flange, Whizlock, 1/ CAP Footnotes 31

32 Wheels & Tires Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. W

33 Wheels & Tires Group REF NO PART NO. QTY. DESCRIPTION KEY, Square, 3/16 x 3/16 x 1-1/2 long REAR WHEEL & TIRE ASSEMBLY, Hoosier, (Includes Ref. Nos. 3, 4, 7 & 8) SPACER WASHER, 3/ VALVE STEM & CAP REAR WHEEL ASSEMBLY, Metallic Gray TIRE, Rear Wheel, 16 X TUBE, Rear Wheel WASHER, 3/ E RING HUB CAP, Silver FRONT WHEEL & TIRE ASSEMBLY, Hoosier, 13 x , Metallic Gray (Includes Ref. Nos. 4, 15, 18 & 19) FRONT WHEEL ASSEMBLY 13 x , Metallic Gray (Includes Ref. No. 16) TIRE, Front Wheel, 13 x TUBE, Front Wheel, 4.10/3.50 x KLIP RING Footnotes 33

34 Decals Group - Brand & Model NOTE: Unless noted otherwise, use the standard hardware torque specification chart. B , , ,

35 Decals Group - Brand & Model REF NO PART NO. QTY. DESCRIPTION 1 * 1 DECAL, C E, (Export Only) DECAL, Icon, Simplicity DECAL, Seat Deck, LH DECAL, Seat Deck, RH DECAL, Touch-up Paint, Deep Orange & Charcoal Gray DECAL, "CORONET" DECAL, 13 HP DECAL, 16 HP DECAL, Simplicity DECAL, Briggs & Stratton, 13 HP, INTEK DECAL, Logo, AGCO DECAL, Seat Deck AGCO, LH DECAL, Seat Deck AGCO, RH DECAL, Model, 413H DECAL, Touch-up Pain, Red & Gray DECAL, Logo, Massey Ferguson DECAL, Seat Deck, LH DECAL, Seat Deck, RH DECAL, Model, 2413 Footnotes Note* Not a servicable part. 35

36 Decals Group - Common & Safety NOTE: Unless noted otherwise, use the standard hardware torque specification chart. C ,

37 Decals Group - Common & Safety REF NO PART NO. QTY. DESCRIPTION DECAL, Operating Instructions, English DECAL, Operating Instructions, Export DECAL, USA (Seat Back) DECAL, Transmission Release (Hydro models only) DECAL, Belt & Blade Replacement 5 * 1 I.D. PLATE (Not Serviced) DECAL, Danger, Rotating Cutting Blade 7 * 1 DECAL, OPEI, (Not Serviced) DECAL, Cutting Width - 34", Silver on Black DECAL, Danger, Chute In Place DECAL, Cutting Width - 30", Silver on Black DECAL, Free Floating Mower Footnotes Note* Not a servicable part. 37

38 30" Mower Deck - Drive & Arbor NOTE: Unless noted otherwise, use the standard hardware torque specification chart " Mower " Mower " Mower " Mower 38

39 30" Mower Deck - Drive & Arbor REF NO PART NO. QTY. DESCRIPTION V-BELT NUT, Hex Flange, 9/ WASHER, Belleville PULLEY HUB, Pulley, 1-3/ CAPSCREW, Hex Head, Taptite, 5/16-18 x A 1 ADAPTER, Arbor GASKET, Foam ARBOR HOUSING ASSEMBLY (Incl. Ref. No. 10) FITTING, Grease BEARING SPACER A 1 COVER, Arbor Housing WASHER, Cupped SHAFT, Arbor, 5-53/64" SHIELD, Grass, Lower A 1 BLADE, Mower, 30" WASHER, Hex WASHER, Spring CAPSCREW, Hex Head, 7/16-14 x 1, GR CAPSCREW, Hex Head, 3/8-16 x WASHER, Flat, 3/8 x 1-1/2 x 1/ SPRING A 1 SPACER LEVER ASSEMBLY WASHER, Plain, 3/ PULLEY ASSEMBLY Idler, Fixed, 6" Dia NUT, Hex, Whizlock, 3/ GRIP, Lever CAPSCREW, Hex Head, 3/8-16 x WASHER, 13/32 x 1 x 1/ IDLER PULLEY, Backside LOCKWASHER, 3/ NUT, Hex, 3/ NUT, Hex, Lock, 3/8-16 Footnotes " Mower " Mower " Mower " Mower 39

40 30" Mower Deck - Housing & Height Adjustment (CE) NOTE: Unless noted otherwise, use the standard hardware torque specification chart Insert Away from Capscrew , Mulcher Only " Mower 40

41 30" Mower Deck - Housing & Height Adjustment (CE) REF NO Footnotes PART NO. QTY. DESCRIPTION CAP, Spring End SPRING NUT, Hex, ALUM Lock, 3/ SPACER ROD, Adjustment NUT, Hex, 5/ LOCKWASHER, 5/ WASHER NUT, Hex, 1/ LOCKWASHER, 1/ A 1 ARM ASSEMBLY, Mower JAMNUT, Hex, 3/ SPACER A 1 TRUNNION PIN, Locking A 2 BAR, Mower Transport CARRIAGE BOLT, 3/8-16 x 1-1/ PIN, Retaining CARRIAGE BOLT, 5/15-18 x 1-1/ SPACER CLAMP WASHER, Plain (1 Required for Export) SPACER (Export) PUSHNUT, 1/ WASHER, Flat, 3/ A 2 PLATE, Pivot Support HOUSING ASSEMBLY, 30" (Orange) HOUSING ASSEMBLY, 30" (Red) HOUSING ASSEMBLY, 30" (Black) BOLT, Shoulder WASHER, Flat A 2 SUPPORT ASSEMBLY, Roller NUT, Hex, Flange, Whizlock, 3/ NUT, Adjustment WASHER, Plain, 21/32 x 1-1/8 x 7/ ROLLER WASHER, 21/32 x 1-1/8 x 1/ RING, Retaining CAPSCREW, Taptite, 5/16-18 x 3/ CARRIAGE BOLT, 5/16-18 x 3/4, G A 1 PLATE, Discharge (30" Mulcher) CAPSCREW, Hex, 3/8-16 x SPACER ROD, Latch, Hitch " Mower 41

42 30" Mower Deck - Housing & Height Adjustment (CE) NOTE: Unless noted otherwise, use the standard hardware torque specification chart Insert Away from Capscrew , Mulcher Only " Mower 42

43 30" Mower Deck - Housing & Height Adjustment (CE) REF NO PART NO. QTY. DESCRIPTION A 1 HITCH ASSEMBLY CAPSCREW, Hex Head, 3/8-16 x SPRING CARRIAGE BOLT, 1/4-20 x 3/ CARRIAGE BOLT, 1/4-20 x 1-1/4 (Export) ROD, Deflector DEFLECTOR, Plastic Footnotes " Mower 43

44 30" Mower Deck - Housing, Hitch & Height Adjustment NOTE: Unless noted otherwise, use the standard hardware torque specification chart Insert Away from Capscrew , " Mower " Mower 44

45 30" Mower Deck - Housing, Hitch & Height Adjustment REF NO Footnotes PART NO. QTY. DESCRIPTION CAP, Spring End SPRING NUT, Hex, ALUM Lock, 3/ SPACER ROD, Adjustment NUT, Hex, 5/ LOCKWASHER, 5/ WASHER NUT, Hex, 1/ LOCKWASHER, 1/ A 1 ARM ASSEMBLY, Mower JAMNUT, Hex, 3/ SPACER A 1 TRUNNION PIN, Locking CARRIAGE BOLT, 3/8-16 x 1-1/ PIN, Retaining CARRIAGE BOLT, 5/15-18 x 1-1/ SPACER CLAMP WASHER, Plain (1 Required for Export) SPACER (Export) PUSHNUT, 1/ WASHER, Flat, 3/ A 2 PLATE, Pivot Support HOUSING ASSEMBLY, 30" (Orange) HOUSING ASSEMBLY, 30" (Red) HOUSING ASSEMBLY, 30" (Black) BOLT, Shoulder WASHER, Flat A 2 SUPPORT ASSEMBLY, Roller NUT, Hex, Flange, Whizlock, 3/ NUT, Adjustment WASHER, Plain, 21/32 x 1-1/8 x 7/ ROLLER WASHER, 21/32 x 1-1/8 x 1/ RING, Retaining CAPSCREW, Taptite, 5/16-18 x 3/ A 2 BAR, Mower Transport CAPSCREW, Hex, 3/8-16 x SPACER ROD, Latch, Hitch A 1 HITCH ASSEMBLY CAPSCREW, Hex Head, 3/8-16 x " Mower " Mower 45

46 30" Mower Deck - Housing, Hitch & Height Adjustment NOTE: Unless noted otherwise, use the standard hardware torque specification chart Insert Away from Capscrew , " Mower " Mower 46

47 30" Mower Deck - Housing, Hitch & Height Adjustment REF NO PART NO. QTY. DESCRIPTION SPRING CARRIAGE BOLT, 1/4-20 x 3/ CARRIAGE BOLT, 1/4-20 x 1-1/4 (Export) ROD, Deflector DEFLECTOR, Plastic Footnotes " Mower " Mower 47

48 34" Mower Deck - Drive & Arbor NOTE: Unless noted otherwise, use the standard hardware torque specification chart Torque to ft/lbs Nm Torque to ft/lbs Nm Torque to ft/lbs Nm Torque to ft/lbs Nm " Mower 48

49 34" Mower Deck - Drive & Arbor REF NO PART NO. QTY. DESCRIPTION NUT, Hex, Flange, 9/ WASHER, Belleville PULLEY, 5" HUB, Pulley, 1-35/64" A 2 COVER, Arbor Housing ASSEMBLY BEARING SPACER GASKET, Foam ARBOR HOUSING ASSEMBLY, (Includes Ref. No. 10) FITTING, Grease WASHER SPRING CAPSCREW, 3/8-16 x 2-1/ WASHER, Flat, 3/ PULLEY, Idler, Backside SPACER LOCKWASHER, 3/ NUT, Hex, 3/ NUT, Hex, Flange, Lock, 3/ CAPSCREW, Hex Head, 3/8-16 x 2-3/ SPACER GRIP, Lever LEVER ASSEMBLY WASHER, Flat, 3/ V-BELT PULLEY, 3-3/4" HUB, Pulley, 1-3/16" SHAFT, Arbor, 5-53/64" SHIELD, Grass, Lower A 1 BLADE, 14-27/64" WASHER, Hex WASHER, Spring CAPSCREW, Hex Head, 7/16-14 x 1-1/4, GR CAPSCREW Taptite, 5/16-18 x 3/ NUT, Hex, 3/ SHAFT, Arbor, 6-33/64" A 1 BLADE, 19-29/32" Footnotes " Mower 49

50 34" Mower Deck - Height Adjustment NOTE: Unless noted otherwise, use the standard hardware torque specification chart. J Insert Away from Capscrew Insert Away from Capscrew " Mower 50

51 34" Mower Deck - Height Adjustment REF NO PART NO. QTY. DESCRIPTION NUT, Hex, 5/ LOCKWASHER, 5/ WASHER SPACER A 1 ARM ASSEMBLY CARRIAGE BOLT, 5/16-18 x 1-1/ PIN, Locking CARRIAGE BOLT, 3/8-16 x 1-1/ CLIP, Hair Pin A 2 BAR, Mower Transport SPACER, Roller WASHER, Flat, 5/ ROLLER SHAFT ASSEMBLY, Roller (Includes Ref. 20) NUT, Adjustment A 1 PLATE, Support, RH NUT, Hex Alum Lock, 3/ BOLT, Shoulder, 3/ WASHER, Flat, 1/ NUT, Push NUT, Flange Lock, 3/ CAPSCREW, Taptite, 5/16-18 x 5/ COVER, Arbor A 1 PLATE, Support Footnotes " Mower 51

52 34" Mower Deck - Housing, Hitch & Deflector NOTE: Unless noted otherwise, use the standard hardware torque specification chart Insert Away from capscrew " Mower 52

53 34" Mower Deck - Housing, Hitch & Deflector REF NO PART NO. QTY. DESCRIPTION NUT, Hex, 1/ LOCKWASHER, 1/ WASHER, Flat, 17/64 x 27/32 x 1/ A 1 ROD, Deflector JAMNUT, Hex, 1/ SPACER A 1 TRUNNION ROD, Adustment CARRIAGE BOLT, 1/4-20 X 7/ HOUSING ASSEMBLY, 34" (Orange) HOUSING ASSEMBLY, 34" (Black) CAPSCREW, Hex Head, 3/8-16 x 1-1/ WASHER, Flat, 3/ SPACER CAPSCREW, Hex Head, 3/8-16 x ROD, Latch, Hitch A 1 HITCH ASSEMBLY NUT, Hex Lock, Alm Insert, 3/ SPRING SPACER PUSHNUT CLAMP WASHER SPRING DEFLECTOR, Plastic CAP, Spring End Footnotes " Mower 53

54

55 Hardware Identification & Torque Specifications Common Hardware Types Hex Head Capscrew Washer Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Carriage Bolt Lockwasher Hex Nut Standard Hardware Sizing When a washer or nut is identified as 1/2, this is the Nominal size, meaning the inside diameter is 1/2 inch; if a second number is present it represent the threads per inch When bolt or capscrew is identified as 1/2-16 x 2, this means the Nominal size, or body diameter is 1/2 inch; the second number represents the threads per inch (16 in this example, and the final number is the body length of the bolt or screw (in this example 2 inches long). The guides and ruler furnished below are designed to help you select the appropriate hardware and tools. 0 1/4 1/2 3/4 1 1/4 1/2 3/4 2 1/4 1/2 3/4 3 1/4 1/2 3/4 Screw, 1/2 x 2 Body Diameter Body Length Nut, 1/2 Inside Diameter Hardware Grade No Marks SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm / / / / / / / / / / / / / / / / / / , ,000 1,360.0 NOTES 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. for prevailing torque locknuts - use 65% of grade 5 torques. b. for flange whizlock nuts and screws - use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings, all torque values must meet this specification. 4 Wrench & Fastener Size Guide 1/4 5/16 3/8 7/16 DIA. 1/2 DIA. 1/4 Bolt or Nut Wrench 7/16 5/16 Bolt or Nut Wrench 1/2 3/8 Bolt or Nut Wrench 9/16 7/16 Bolt or Nut Wrench (Bolt) 5/8 Wrench (Nut) 11/16 1/2 Bolt or Nut Wrench 3/4

56 MANUFACTURING, INC. 500 N. Spring Street / PO Box 997 Port Washington, WI USA Copyright 2005 Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA.