Reproduction. Not for. Large Frame Dual Stage Snowthrowers. Parts Manual. Attachment

Transcription

1 Parts Manual Attachment Large Frame Dual Stage Snowthrowers Mfg. No. Description (L1528E), 14.5TP 28" Dual Stage Snowthrower (L1730E), 16.5GT 30" Dual Stage Snowthrower (L1428EX), 14.5TP 28" Dual Stage Snowthrower (CE/Export) (L1730EX), 16.5TP 30" Dual Stage Snowthrower (CE/Export) Not for Reproduction Manual Part No. Revision - Rev. Date: 7/20/2011

2

3 Table Of Contents PRODUCT COMPONENTS PAGES Handles & Controls Group... 4 Engine & Frame Group TP & 16.5TP... 8 Auger Drive Group - Heavy Duty Auger Housing Group Traction Drive Group - Easy Turn Wheels & Tires Group Decals Group Chute & Rotation Group - Full Electric Gear Case Assembly - Heavy Duty Torque Specification Chart... Inside Back Cover Not for Reproduction

4 Handles & Controls Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

5 Handles & Controls Group REF NO PART NO. QTY. DESCRIPTION HEADLIGHT ASSEMBLY * BULB, Headlight, Halogen, V 27W (Included with Ref. No. 0010) C 1 COVER, Panel SCREW, Truss Head Torx, 1/4-20 x 3/ CABLE AND SPRING ASSEMBLY, Auger Drive, Right A 1 HANDLE, Lower A 1 HANDLE, Upper, Right A 1 HANDLE, Upper, Left CAPSCREW, Hex Head, 5/16-18 x 1 G SCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ NUT, Hex Flange, Two Way Lock, 5/ KNOB, Wing, 5/ BOLT, Carriage, 5/16-18 x 2-1/4 G WASHER, Internal Tooth, 5/ NUT, Hex Lock, ESNA Light, 1/ SPACER, 1/4ID x 3/8OD CAPSCREW, Hex Head, 1/4-20 x 1-3/4 G A 1 LEVER, Clutch, Right A 1 LEVER, Clutch, Left BM 1 BRACKET, Pivot, Free Hand ROD, 5-5/8 Inch SPACER, 1/4ID x 3/8OD WASHER, 1/ SPACER, Stepped BOLT, Shoulder, 1/4 x 1-1/ NUT, Hex Lock, Nylon Insert, HAND GRIP NUT, Hex, 5/ BALL JOINT ROD, 25" CAPSCREW, Hex Head, 3/8-16 x 2 G NUT, Hex Flange, Whiz Lock, 5/ SPRING WASHER, 3/ NUT, Hex Lock, Esna Light, 3/ BRACKET, Controls SCREW, Phillips, #10-24 x 3/ GRIP, Lever NUT, Hex Lock Nylon Insert, SPEED LEVER CABLE, Hydro Drive BOOT, Spring End Cover BRACKET, Cable Adjusting ROD & SPRING ASSEMBLY Not for Reproduction Footnotes Note* See your local hardware store for replacement bulbs. 5

6 Handles & Controls Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

7 Handles & Controls Group REF NO PART NO. QTY. DESCRIPTION SPRING, Compression SCREW, Hex Washer Head, Taptite, 1/4-20 x 5/ BOLT, Carriage, 5/16-18 x 3/ BM 1 COVER, Dash TIE, Self Lock WIRING HARNESS WASHER, Flat NUT, Hex Nylock, 1/ BOLT, Carriage, Short Neck, 5/16-18 x 2 Not for Reproduction Footnotes Note* See your local hardware store for replacement bulbs. 7

8 Engine & Frame Group TP & 16.5TP NOTE: Unless noted otherwise, use the standard hardware torque specification chart

9 Engine & Frame Group TP & 16.5TP REF NO PART NO. QTY. DESCRIPTION M H1 1 * ENGINE, 14.5TP Briggs & Stratton (2011 Domestic 28") (Engine Model: 20M H1) (CE/Export Models Only) M F1 1 * ENGINE, 16.5TP Briggs & Stratton (2011 Domestic 30") (Engine Model: 20M H1) (CE/Export Models Only) M H1 1 * ENGINE, 14.5TP Briggs & Stratton (2011 Export 28") (Engine Model: 21M H1) (CE/Export Models Only) M H1 1 * ENGINE, 16.5TP Briggs & Stratton (2011 Export 30") (Engine Model: 20M H1) (CE/Export Models Only) GUARD, Muffler, Plate (Domestic) GUARD, Muffler, Cage (Export) CAPSCREW, Hex Washer Head, Muffler Guard CAP, Fuel CORD, 10FT, 110V (Domestic Only) BOLT, Carriage, 5/16-18 x 1-1/ NUT, Push, For 1/4 Stud NUT, Hex Flange, ESNA, 5/ PULLEY WASHER, 5/ CAPSCREW, Hex Head, 3/8-24 x 1-1/4, G V-BELT, Drive, 3L V-BELT, 4L, 38.35, Auger BELT GUIDE LOCKWASHER, Spring, 5/ CAPSCREW, Hex Head, 5/16-24 x 3/4, G BRACKET, Idler BUSHING, Idler Bracket SPRING, Extension, Idler IDLER, Plastic Ball Bearing NUT, Hex Center Lock Jam, 3/ BOLT, Carriage, Short Neck, 3/8-16 x 1-1/4, G AUGER IDLER SPACER, 1/2 ID x 1 OD x 1-3/4" WASHER, 1/ ARM, Control PIN, Hair PIN, Clevis BM 1 PANEL, Bottom CAPSCREW, Hex Washer Head, Taptite, 1/4-20 x 5/ SPRING, Extension, Auger C 1 FRAME C 1 PLATE, Engine Mount CAPSCREW, Hex Washer Head, 5/16-18 x 1/ CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ BELT COVER ASSEMBLY SCREW, Hex Washer Head, Tapping, SEMS, 1/4 x 3/ WATER SHIELD ASSEMBLY (Includes Ref. No ) SEAL, Shaft Not for Reproduction Footnotes Note* See your local Briggs & Strattion Distributor for Parts & Service. 9

10 Engine & Frame Group TP & 16.5TP NOTE: Unless noted otherwise, use the standard hardware torque specification chart

11 Engine & Frame Group TP & 16.5TP REF NO PART NO. QTY. DESCRIPTION CAPSCREW, Hex, 5/16-24 x PIN, Cotter, Self Lock, 1/ WASHER, 3/16 (16.5TP Models) LOCKWASHER, Spring, 3/8 (14.5TP Models) WASHER, 3/8 (Qty. 1 in Domestic Models) WASHER, Flat, 3/8 (Qty. 2 in Domestic Models) SEAL, Engine Plate OIL DRAIN ASSEMBLY Not for Reproduction Footnotes Note* See your local Briggs & Strattion Distributor for Parts & Service. 11

12 Auger Drive Group - Heavy Duty NOTE: Unless noted otherwise, use the standard hardware torque specification chart

13 Auger Drive Group - Heavy Duty REF NO PART NO. QTY. DESCRIPTION BM 1 AUGER ASSEMBLY, 28", R.H BM 1 AUGER ASSEMBLY, 28", L.H BOLT, Carriage, 5/16-18 x 3/ NUT, Hex Flange, Whiz Lock, 5/ GEAR CASE ASSEMBLY, Heavy Duty KEY, Woodruff A 1 IMPELLER SCREW, Set, 3/8-16 x 1/2, G SCREW, Set, 5/16-18 x 1/2, G PULLEY, 8.40 OD, 3/4 ID PIN, Shear, 1-3/ PIN, Cotter SPACER (30" Housing Only) Not for Reproduction Footnotes 13

14 Auger Housing Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

15 Auger Housing Group REF NO PART NO. QTY C C BM YP BM BM BM SM BM 2 DESCRIPTION AUGER HOUSING ASSEMBLY, 28" AUGER HOUSING ASSEMBLY, 30" DRIFT CUTTER NUT, Wing, Serrated, 5/16-18 BOLT, Carriage, 5/16-18 x 3/4 NUT, Hex Flange, 5/16-18 NUT, Retainer, 5/16-18 BLADE, Scraper, 28" BLADE, Scraper, 30" BOLT, Carriage, 5/16-18 x 5/8, G5 NUT, Hex Flange, Two Way Lock, 5/16-18 BOLT, Carriage, 5/16-18 x 3/4, G5 SHOE, Skid, Reversible NUT, Hex Flange, ESNA, 3/8-16 BEARING, Flange CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 1-1/4 NUT, Nylock, 10 x 24 CLAMP, Retainer SCREW, Truss Head Torx, #10-24 x 3/8 BRUSH, Cleanout BEARING, Ball RETAINER, Ball Bearing BOLT, Carriage, 5/16-18 x 3/4, G5 CAPSCREW, Hex Flange, Whiz Lock, 5/16-18 x 3/4 COVER, Bushing Not for Reproduction Footnotes 15

16 Traction Drive Group - Easy Turn NOTE: Unless noted otherwise, use the standard hardware torque specification chart

17 Traction Drive Group - Easy Turn REF NO PART NO. QTY. DESCRIPTION CHAIN, Roller 420 x 19" Lg RETAINER & BUSHING ASSEMBLY WASHER, Flat, 1/ CAPSCREW, Hex Washer Head, 5/16-18 x 1/ CHAIN, Roller 420 X 18 Lg RETAINER, Ring, 7/ SPRING LINK ASSEMBLY SPRING, Extension WASHER, 1/ AXLE, Swing Plate, 7/16 Dia., 10-1/2 Lg FITTING, Lube, 1/ HEX SHAFT & SPROCKET ASSEMBLY HUB, Friction Wheel & Bearing WHEEL, Friction CAPSCREW, Hex Head, 1/4-20 x 5/8, G NUT, Hex, 1/ RING, Retaining, # NUT, Flange Lock, 3/ PLATE, Swinging SPACER, Friction Pulley FRICTION PULLEY ASSEMBLY SPEED SELECTOR ASSEMBLY BEARING, Flange, 1/2 ID X 7/8 OD ASSEMBLY, Sprocket & Hub w/ Bushings AXLE, 3/4 Dia. x 22-3/4 Lg GEAR, Clutching 3/4 ID 17/8 OD 1.50 Lg RING, Retaining, # 74, 3/4 Dia A 1 SUPPORT, Cable SPROCKET & SHAFT ASSEMBLY A 1 ARM, Clutch RING, Retaining, 1/2 Dia SPOOL CABLE, Auger Control BRACKET, Cablel Spool CABLE, Front Drive, Lower NUT, Hex Lock, 1/ CAPSCREW, Hex Head, 1/4-20 x 1-1/2, G WASHER, Flat, 3/4 x 1-1/ KEY, 1-9/ WASHER, 3/ NUT, Hex Flange, Locking, 3/ CAPSCREW, Hex Head, 3/8-16 x 3/4, G BEARING, Ball, 3/4 ID x 1-5/8 OD RETAINER, Bearing, Flanged COLLAR, Locking Not for Reproduction Footnotes 17

18 Traction Drive Group - Easy Turn NOTE: Unless noted otherwise, use the standard hardware torque specification chart

19 Traction Drive Group - Easy Turn REF NO PART NO. QTY. DESCRIPTION SPRING, Compression WASHER, 3/ RETAINER, Bushing BUSHING, 5/ SCREW, Pan Head, #10 x 1/ CABLE & HANDLE ASSEMBLY Not for Reproduction Footnotes 19

20 Wheels & Tires Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

21 Wheels & Tires Group REF NO PART NO. QTY DESCRIPTION WHEEL ASSEMBLY, Artic Trac, 4.80, L.H. (28" Models Only) (Includes Ref. Nos , & ) WHEEL ASSEMBLY, 15 x 5-6, W3, L.H. (30" Models Only) (Includes Ref. Nos , & ) VALVE STEM & CAP TIRE, , 2 Ply, K467 (28" Models Only) TIRE, 16 x 6-1/2-8, K467 (30" Models Only) TUBE, Tire 15 x 5-6 (30" Models Only) *RIM, Tire, L.H. WHEEL ASSEMBLY, Artic Trac, 4.80, R.H. (28" Models Only) (Includes Ref. Nos , & ) WHEEL ASSEMBLY, 15 x 5-6, W3, R.H. (30" Models Only) (Includes Ref. Nos , & ) *RIM, Tire, R.H. PIN, Klik, 5/16 x 2 (28" & 30" Models Only) Not for Reproduction Footnotes * Not a servicable part. Order complete wheel and tire assembly. 21

22 Decals Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

23 Decals Group REF NO PART NO. QTY DESCRIPTION DECAL, Dash Operation DECAL, Gear Shift DECAL, Foot, FR/Eng (Domestic) DECAL, Danger Auger Icons (Export) DECAL, Chute Warning, FR/ENG (Domestic) DECAL, Chute Warning (Export) DECAL, Dash, Logo DECAL, Model, L1528E (Domestic) DECAL, Model, L1528EX (Export) DECAL, Model, L1730E (Domestic) DECAL, Model, L1730EX (Export) DECAL, Logo, Housing, 28" (Export) DECAL, Logo, Housing, 30" (Export) DECAL, Auger Control Symbols DECAL, Traction Control Symbols Not for Reproduction Footnotes 23

24 Chute & Rotation Group - Full Electric NOTE: Unless noted otherwise, use the standard hardware torque specification chart

25 Chute & Rotation Group - Full Electric REF NO PART NO. QTY. DESCRIPTION PINION, 1-1/4 Lg YP 3 SCREW, Torx Button Head, M5 x.8 x SM 3 WASHER, Flat, 7/32 x 1/ CAPSCREW, Hex Washer, Taptite, 1/4-20 x 3/ COVER, Electric Chute Rotation RETAINER, Spout CAPSCREW, Hex Washer, x 5/ SWITCH, Chute Rotation TIE, Self Locking, 7-5/16 Lg DECAL, Hinge C 1 CHUTE ASSEMBLY, Tall, Steel MOTOR, Spout Rotator, 38" BM 1 GEAR, Tall, Steel Chute BOLT, Carriage, 1/4-20 x 3/4, G NUT, Hex Flange, 1/ BM 1 BRACKET ASSEMBLY MOTOR, Chute Deflector SCREW, Truss Head, Torx, 1/4-20 X 3/ NUT, Hex Flange, 1/ SWITCH, Deflector Control WASHER, Rubber NUT, 1/4-20, L.H WASHER, 1/ GUARD, Chute (CE/Export) PUSHNUT, 3/16 Dia. (CE/Export) A 1 BRACKET, Chute Guard (CE/Export) CAPSCREW, Hex Washer, Taptite, 1/4-20 x 1/2 (CE/Export) GROMMET, Chute Guard Bracket (CE/Export) Not for Reproduction Footnotes 25

26 Gear Case Assembly - Heavy Duty NOTE: Unless noted otherwise, use the standard hardware torque specification chart

27 Gear Case Assembly - Heavy Duty REF NO PART NO. QTY. DESCRIPTION CAPSCREW, Hex Head, 1/4-20 x 2-1/ CAPSCREW, Hex Head, 1/4-20 x 2-1/ GEAR CASE, L.H FITTING, Pipe Plug GASKET SHAFT, Auger Cutoff SHAFT, Worm Cutoff SEAL, Oil FLANGE BUSHING PIN, Drive Lock THRUST COLLAR WORMGEAR, 1-3/4 OD x 1-3/8 Long THRUST WASHER THRUST WASHER WORMGEAR, 21T, 3" O.D. x 7/8 Long GEAR CASE, R.H NUT, Top Lock Flange 1/ SEAL BRACKET, Support KEY, Woodruff.18 x BUSHING TUBE KEY, Woodruff 1/4 x 3/4 Not for Reproduction Footnotes 27

28

29 Not for Reproduction

30

31 Hardware Identification & Torque Specifications Torque Specification Chart FOR STANDARD METRIC MACHINE HARDWARE (Tolerance ± 20%) Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Property Class 5.6 Class Class 8.8 Class 10.9 Class 12.9 Size Of in/lbs in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. M M M M M M M M M M M M M M M M M M M The guides and ruler furnished below are designed to help you select the appropriate hardware Inside Diameter (in) Nut, 1/2-16 1/4 1/2 3/ /4 1/2 3/ Thread Diameter (mm) Body Diameter 2 Screw, 1/2-16 x 2 1/4 1/2 3/ Body Diameter Nut, M8 Screw, M x 25 Thread Diameter (mm) Threads per inch Not for Body Length 1/4 1/2 3/4 4 Hardware Grade No Marks Reproduction Distance between threads (mm) Threads per inch Body Length (mm) Body Length (in) SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm / / / / / / / / / / / / / / / / / / , ,000 1,360.0 NOTES 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. for prevailing torque locknuts - use 65% of grade 5 torques. b. for flange whizlock nuts and screws - use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings, all torque values must meet this specification. Common Hardware Types Hex Head Capscrew Washer Standard Hardware Sizing When a washer or nut is identified as 1/2 (M8), this is the Nominal size, meaning the inside diameter is 1/2 inch (8mm metric thread diameter); if a second number is present it represents the threads per inch (distance between threads). Carriage Bolt Wrench & Fastener Size Guide Lockwasher Hex Nut When bolt or capscrew is identified as 1/2-16 x 2 (M x 50 ), this means the Nominal size, or body diameter is 1/2 inch (8mm metric thread diameter), the second number,16, represents the threads per inch, (1.25 thread diameter). The final number is the body length of the bolt or screw, 2 inches (50mm). 1/4 Bolt or Nut Wrench 7/16 M6 Bolt or Nut Wrench 10mm 5/16 Bolt or Nut Wrench 1/2 M8 Bolt or Nut Wrench 13mm 3/8 Bolt or Nut Wrench 9/16 M10 Bolt or Nut Wrench 17mm 7/16 Bolt or Nut Wrench (Bolt) 5/8 Wrench (Nut) 11/16 M12 Bolt or Nut Wrench 19mm 1/2 Bolt or Nut Wrench 3/4 M14 Bolt or Nut Wrench 22 mm

32 IT IS THE POLICY OF BRIGGS & STRATTON CORP. TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS. Briggs & Stratton Yard Power Products Group 3515 N. 124 Street / PO Box 702 Wauwatosa, WI USA