Reproduction. Not for. Hybrid Frame Dual Stage Snowthrowers. Parts Manual

Size: px

Start display at page:

Download "Reproduction. Not for. Hybrid Frame Dual Stage Snowthrowers. Parts Manual"

Kathlyn Gardner
5 years ago
Views:

1 Parts Manual Attachment Mfg. No. Description (I924E), 9TP 24" Dual Stage Snowthrower (H924RX), 9TP 24" Dual Stage Snowthrower (CE/Export) Hybrid Frame Dual Stage Snowthrowers Not for Reproduction Manual Part No. Revision - Rev. Date: 7/20/2011

3 Table Of Contents PRODUCT COMPONENTS PAGES Handles & Controls Group - Light... 4 Handles & Controls Group - No Light... 8 Engine & Frame Group - 9TP Auger Drive Group Auger Housing Group Traction Drive Group Traction Drive Group Wheels & Tires Group - 1 Pin Decals Group Decals Group Discharge Chute Group Gear Case Assembly Torque Specification Chart... Inside Back Cover Not for Reproduction

4 Handles & Controls Group - Light NOTE: Unless noted otherwise, use the standard hardware torque specification chart

5 Handles & Controls Group - Light REF NO PART NO. QTY. DESCRIPTION HEADLIGHT ASSEMBLY BULB, (Included with Ref. No. 0010) C 1 COVER, Panel SCREW, Truss Head Torx, 1/4-20 x 3/ CABLE & SPRING ASSEMBLY, Auger, R.H A 1 HANDLE, Lower A 1 HANDLE, Upper, R.H A 1 HANDLE, Upper, L.H BOLT, Carriage, 5/16-18 x 3/ NUT, Hex, KEPS, Conical Washer, 5/ WINGKNOB, Hex 5/ BOLT, Carriage, 5/16-18 x 2-1/ BOLT, Carriage, 5/16-18 x 1-3/ WASHER, Locking, Internal Tooth NUT, Hex Lock, 1/4-20, ESNA Light SPACER, 1/4 ID x 3/8 OD x 5/ CAPSCREW, Hex Flange Head, 1/4-20 x 1-3/ A 1 LEVER, Clutch, R.H A 1 LEVER, Clutch, L.H A 1 BRACKET, Pivot, Free Hand ROD, 5-5/ SPACER, 1/4 ID x 3/8 OD x 1/ WASHER, 1/ SPACER, Stepped CAPSCREW, Shoulder, Hex Flange Head, NUT, Nylock, GRIP NUT, Hex, 5/ LOCKWASHER, Spring BALLJOINT, Quick Release ROD, 25-3/ CAPSCREW, Hex Head, 3/8-16 x NUT, Hex Flange, Whiz Lock, 5/ SPRING, 3/ WASHER, 3/ NUT, Hex Lock, 3/8-16, ESNA Light BRACKET, Controls SCREW, Round Head Phillips, #10-24 x 3/ KNOB, Slot Speed NUT, Hex Lock, LEVER, Speed CABLE, Front Drive BOOT, Spring End Cover BRACKET, Cable Adjusting Not for Reproduction Footnotes Note* See your local hardware store for replacement bulbs. 5

6 Handles & Controls Group - Light NOTE: Unless noted otherwise, use the standard hardware torque specification chart

7 Handles & Controls Group - Light REF NO PART NO. QTY. DESCRIPTION ROD & SPRING ASSEMBLY, With Pin SPRING, Compression CAPSCREW, Hex Washer Head, Taptite, 1/4-20 x 5/ A 1 COVER, Dash TIE, Self Locking WIRING HARNESS Not for Reproduction Footnotes Note* See your local hardware store for replacement bulbs. 7

8 Handles & Controls Group - No Light NOTE: Unless noted otherwise, use the standard hardware torque specification chart

9 Handles & Controls Group - No Light REF NO PART NO. QTY. DESCRIPTION C 1 PANEL,Dash A 1 LEVER, Clutch, LH BOLT, Shoulder, CAPSCREW, Hex Head, 1/4-20 x 1-3/4, G NUT, Hex Lock, ESNA Light, 1/ CABLE & SPRING ASSEMBLY, RH A 1 LEVER, Clutch, RH NUT, Hex Nylon Insert Lock, GRIP SPACER, Stepped SPACER, 1/4 ID x 3/8 OD A 1 HANDLE, Upper, RH A 1 HANDLE, Upper, LH BOLT, Carriage, Short Neck, 5/16-18 x 2-1/4, G A 1 HANDLE, Lower NUT, Hex Flange, ESNA, 5/ BOLT, Carriage, 5/16-18 x 3/4, G NUT, Hex, KEPS, Conical Washer, 5/ BRACKET, Cable Adjusting BOOT, Spring End Cover CABLE, Front Drive BOLT, Carriage, Short Neck, 5/16-18 x 1-3/4, G A 1 ROD, Shift BOLT, Hex, 1/4-20 x 3/4, G NUT, Hex Centerlock, 1/ GRIP, Lever NUT, Hex Jam, 1/ LEVER, Spring Shift C 1 BRACKET, Gear Select CAPSCREW, Hex Washer Head, Taptite, 1/4-20 x 5/ BOLT, Carriage, Short Neck, 1/4-20 x 1-1/4, G SCREW, Pan Head Torx, Taptite, 1/4-20 x 3/4 Not for Reproduction Footnotes 9

10 Engine & Frame Group - 9TP NOTE: Unless noted otherwise, use the standard hardware torque specification chart. ata\smp\images\groups\ \

11 Engine & Frame Group - 9TP REF NO PART NO. QTY. DESCRIPTION D E8 1 * ENGINE, 9TP Briggs & Stratton (Engine Model: 12D E8) D E8 1 * ENGINE, 9TP Briggs & Stratton (Engine Model: 12D E8) (CE/Export) * GUARD, Muffler (Domestic) * GUARD, Muffler (CE / Export) * SCREW, Muffler Guard * CAP, Fuel CORD, Electric SCREW, Hex Head, Trilobular, 3/8-16 x 1-1/ PULLEY WASHER, 5/ CAPSCREW, Hex Head, 5/16-24, 1-3/4, G V-BELT, Traction Drive, 3L, BELT, Auger Drive, V4L SEAL, Strip STOP, Belt LOCKWASHER, Spring, 5/16 (Qty 3 used on 14.5TP models) CAPSCREW, Hex Head, 5/16-24 x 3/4, G BRACKET, Idler BOLT, Carriage, Short Neck, 5/16-18 x 1, G NUT, Hex KEPS, 5/ BUSHING, Idler Bracket SPRING, Extension, Idler IDLER NUT, Hex Nylock, 3/ NUT, Hex Centerlock Jam, 3/ BOLT, Carriage, Short Neck, 3/8-16 x 1-1/2, G IDLER, Auger SPACER, Auger Bracket WASHER, 1/ ARM, Control PIN, Hair PIN, Clevis A 1 PANEL, Bottom SCREW, Hex Washer Head, Taptite, 1/4-20 x 5/ SPRING, Extension, Auger C 1 FRAME A 1 ANGLE, Auger & Traction Rod Mounting C 1 PLATE, Engine SCREW, Hex Washer Head, Taptite, 5/16-18 x 3/ COVER, Belt SCREW, Hex Washer Head, Tap, SEMS, 1/4-20 x 3/ A 1 PLATE, Seal (Used on 11.5TP Models) SEAL, Foam (Used on 11.5TP Models) BOLT, Hex, 5/16-24 x 1 Not for Reproduction Footnotes Note* See your local Briggs & Strattion Distributor for Parts & Service. NOTE: * Purchase engine parts from engine manufacturer dealer. 11

12 Engine & Frame Group - 9TP NOTE: Unless noted otherwise, use the standard hardware torque specification chart. ata\smp\images\groups\ \

13 Engine & Frame Group - 9TP REF NO PART NO. QTY. DESCRIPTION PIN, Cotter, Self Locking, 1/4" Not for Reproduction Footnotes Note* See your local Briggs & Strattion Distributor for Parts & Service. NOTE: * Purchase engine parts from engine manufacturer dealer. 13

14 Auger Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

15 Auger Drive Group REF NO PART NO. QTY A A A DESCRIPTION GEAR CASE ASSEMBLY KEY, Square, 3/16 x 3/4 IMPELLER HUB, Impeller SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/8 SET SCREW, Socket Head, 5/16-18 x 1/2 PULLEY CAPSCREW, Hex Head, 1/4-20 x 1-3/4, G2 NUT, Center Lock, 1/4-20 AUGER, 24", LH AUGER, 24", RH FITTING, Grease KIT, Shear Bolt KIT, Shear Bolt (Includes Ref. Nos & 0170) Not for Reproduction Footnotes 15

16 Auger Housing Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

17 Auger Housing Group REF NO PART NO. QTY C A A DESCRIPTION AUGER HOUSING CLAMP, Spring SCREW, Truss Head Torx, #10-24 x 3/8 NUT, Hex Lock, Nylon\, #10C BRUSH, Cleanout BEARING, Auger, RH BEARING, Auger, LH CAPSCREW, Hex Flange, 1/4-20 x 3/4 BOLT, Carriage, Short Neck, 3/8C x 3/4, GR5 NUT, Hex Flange Lock, 3/8C NUT, Hex Flange Serrated Lock, 5/16-18 SKID SHOE BLADE, Scraper, 24 RETAINER, Ball Bearing BEARING, Ball, 11/16 x 1-9/16 x 15/32 BOLT, Carriage, Short Neck, 5/16C x 3/4, GR5 PLUG, Panel BOLT, Carriage, Short Neck, 5/16C x 5/8, GR5 NUT, Flange Lock, 1/4-20 Not for Reproduction Footnotes 17

18 Traction Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

19 Traction Drive Group REF NO PART NO. QTY DESCRIPTION CHAIN, Roller, 420 x 19" RETAINER & BUSHING ASSEMBLY WASHER, Flat, 1/2 SCREW, Hex Washer Head, Taptite, 5/16-18 x 1/2 CHAIN, Roller, 420 x 18" RETAINER, Ring, 7/16 SPRING LINK SPRING, Extension SPROCKET WASHER, 1/2 AXLE, Swing Plate, 10-1/2" AXLE, 21-3/8" BOLT, Hex, 1/4-20 x 1-3/4 G8 AXLE SPROCKET, 30T BEARING, Axle HEX SHAFT & SPROCKET ASSEMBLY BEARING TRUNNION ASSEMBLY WHEEL, Friction CAPSCREW, Hex Head, 1/4-20 x 5/8, G5 NUT, Hex KEPS, 1/4-20 RING, Retaining, External Tooth NUT, Flange Lock, 3/8-24 PLATE, Swinging SPACER, Friction Pulley FRICTION PULLEY ASSEMBLY SPEED SELECT (Domestic Models Only) SPEED SELECT (Export Models Only) BEARING, Flange, 1/2 ID x 7/5 OD NUT, Hex Lock, ESNA Light, 1/4-20 CAPSCREW, Hex Head, 1/4-20 x 1-1/2, G5 SPOOL CABLE, Auger Control BRACKET, Spool CABLE, Drive BOLT, Hex, 1/4-20 x 5/8 NUT, Hex, 1/4-20, GR5 LOCKWASHER, Spring, 1/4 BRACKET, Support SCREW, Hex Washer Head, Taptite, 1/4-20 x 5/8 Not for Reproduction Footnotes 19

20 Traction Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

21 Traction Drive Group REF NO PART NO. QTY DESCRIPTION CHAIN, Roller, 420 x 19" RETAINER & BUSHING ASSEMBLY WASHER, Flat, 1/2 SCREW, Hex Washer Head, Taptite, 5/16-18 x 1/2 CHAIN, Roller, 420 x 18" RETAINER, Ring, 7/16 SPRING LINK SPRING, Extension SPROCKET WASHER, 1/2 AXLE, Swing Plate, 10-1/2" AXLE, 21-3/8" BOLT, Hex, 1/4-20 x 1-3/4 G8 AXLE SPROCKET, 30T BEARING, Axle HEX SHAFT & SPROCKET ASSEMBLY BEARING TRUNNION ASSEMBLY WHEEL, Friction CAPSCREW, Hex Head, 1/4-20 x 5/8, G5 NUT, Hex KEPS, 1/4-20 RING, Retaining, External Tooth NUT, Flange Lock, 3/8-24 PLATE, Swinging SPACER, Friction Pulley FRICTION PULLEY ASSEMBLY SPEED SELECT (Domestic Models Only) SPEED SELECT (Export Models Only) BEARING, Flange, 1/2 ID x 7/5 OD NUT, Hex Lock, ESNA Light, 1/4-20 CAPSCREW, Hex Head, 1/4-20 x 1-1/2, G5 SPOOL CABLE, Auger Control BRACKET, Spool CABLE, Drive BOLT, Hex, 1/4-20 x 5/8 NUT, Hex, 1/4-20, GR5 LOCKWASHER, Spring, 1/4 BRACKET, Support SCREW, Hex Washer Head, Taptite, 1/4-20 x 5/8 Not for Reproduction Footnotes 21

22 Wheels & Tires Group - 1 Pin NOTE: Unless noted otherwise, use the standard hardware torque specification chart

23 Wheels & Tires Group - 1 Pin REF NO PART NO. QTY. DESCRIPTION WHEEL & TIRE ASSEMBLY, 13 X 5, LH (Includes Ref. No ) VALVE STEM & CAP WHEEL & TIRE ASSEMBLY, 13 X 5, RH (Includes Ref. No ) RING, Retaining WASHER, Flat, 3/ CAPSCREW, Hex, 1/4-20 x 1-3/4, G NUT, Hex Nylock, 1/ PIN, Klik Not for Reproduction Footnotes 23

24 Decals Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

25 Decals Group REF NO PART NO. QTY DESCRIPTION DECAL, Danger Chute, FR/ENG (Domestic Only) DECAL, Chute Warning (CE/Export Only) DECAL, Danger Foot, FR/ENG (Domestic Only) DECAL, Danger Auger Icons (CE/Export Only) DECAL, Auger Control Symbols DECAL, Traction Control Symbols DECAL, Dashboard, Operator's Controls (Domestic Only) DECAL, Dashboard, Free Hand Operatation Panel (Domestic Only) DECAL, Dashboard, Operator's Controls (CE/Export Only) DECAL, Shift, 1, 2, 3, 4, 5, 6 DECAL, Model, I1224E (Domestic Only) DECAL, Model, I924IE (Domestic Only) DECAL, Model, 924IE (CE/Export Only) DECAL, Simplicity Swoosh, Dash Not for Reproduction Footnotes 25

26 Decals Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

27 Decals Group REF NO PART NO. QTY DESCRIPTION DECAL, Control Panel (Domestic) DECAL, Chute Warning (CE/Export) DECAL, Chute Warning (Domestic) DECAL, Danger Auger (CE/Export) DECAL, Danger Auger (Domestic) DECAL, Auger Control Symbols DECAL, Traction Control Symbols DECAL, Simplicity Stripe (CE/Export) DECAL, Housing, Model (Domestic) DECAL, Dash (CE/Export) DECAL, Dash (Domestic) DECAL, Housing, Model (CE/Export) DECAL, 1-6 Transmission Speed Control, Horizontal (CE/Export) DECAL, 1-6 Transmission Speed Control, Vertical (Domestic) Not for Reproduction Footnotes 27

28 Discharge Chute Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

29 Discharge Chute Group REF NO PART NO. QTY C A DESCRIPTION RING, Outer Chute COLLAR, Chute Rotate BOLT, Carriage, 5/16-18 x 1 NUT, Hex Nylock, 5/16-18 WASHER, Flat, 11/32 RING, Inner Chute KNOB, Wing, CHUTE BOLT, Carriage, Short Neck, 1/4-20 x 3/4, G5 NUT, Hex Flange, Nylock, 1/4-20 BOLT, Carriage, 5/16-18 x 1-1/2 WASHER, Nylon ROD, Yoke Crank SPRING, Compression WASHER, Flat, 3/8 GEAR,9 Tooth PIN, Hair, Chute Gear BRACKET, Chute Gear PIN, Cotter YOKE TUBE ASSEMBLY, Adapter PIN, Universal Joint PIN, Clevis BLOCK, Universal Pivot WASHER, Flat, 1/2 NUT, Hex Nylock, 3/8-16 BOLT, Carriage, 1/4-20 x 3/4 GRIP, Chute Crank WASHER, Flat, 1/2 NUT, Push, 3/8 EYEBOLT, 3/8-16 x 6-1/2 GROMMET, Eyebolt BOOT, Eyebolt NUT, Hex Jam, 3/8-16 CRANK, Chute Turn PIN, Hair, 3/8 ADAPTOR, Boot to Handle WASHER, Flat, 1/2 DECAL, Hinge GUARD, Chute (CE/Export) BRACKET, Chute Guard (CE/Export) GROMMET, Chute Guard (CE/Export) NUT, Push, 3/16 Stud (CE/Export) CAPSCREW, Hex Washer Head, Taptite, 1/4-20 x 1/2 (CE/Export) CAPSCREW, Hex Flange Head, 1/4-20 x 3/4, G5 (CE/Export) Not for Reproduction Footnotes 29

30 Gear Case Assembly NOTE: Unless noted otherwise, use the standard hardware torque specification chart

31 Gear Case Assembly REF NO PART NO. QTY YP MA MA MA MA MA MA MA MA MA MA MA MA YP X143MA MA MA 7 DESCRIPTION SHAFT, Impeller COLLAR, Thrust, 3/4 x 1-1/4 PIN, Spring, 1/4 x 1-1/4 WASHER, Thrust BEARING, Roll Thrust, 3/4 x 1-1/4 BEARNG, Flange, 3/4 x 1 SEAL, Oil 3/4 x 1.19 BEARING, Flange 1/2 x 3/4 GEAR CASE, LH GEAR CASE, RH CAPSCREW, Hex Washer Head, Taptite, 3/8-16 x 1/2 KEY, Woodruff, 5/8 SHAFT, Output GEAR, Worm, 22T NUT, Flange, Lock, 1/4-20 GASKET, Gear Case CAPSCREW, 1/4-20 X 3/4 Not for Reproduction Footnotes 31

33 Not for Reproduction

35 Hardware Identification & Torque Specifications Torque Specification Chart FOR STANDARD METRIC MACHINE HARDWARE (Tolerance ± 20%) Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Property Class 5.6 Class Class 8.8 Class 10.9 Class 12.9 Size Of in/lbs in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. M M M M M M M M M M M M M M M M M M M The guides and ruler furnished below are designed to help you select the appropriate hardware Inside Diameter (in) Nut, 1/2-16 1/4 1/2 3/ /4 1/2 3/ Thread Diameter (mm) Body Diameter 2 Screw, 1/2-16 x 2 1/4 1/2 3/ Body Diameter Nut, M8 Screw, M x 25 Thread Diameter (mm) Threads per inch Not for Body Length 1/4 1/2 3/4 4 Hardware Grade No Marks Reproduction Distance between threads (mm) Threads per inch Body Length (mm) Body Length (in) SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm / / / / / / / / / / / / / / / / / / , ,000 1,360.0 NOTES 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. for prevailing torque locknuts - use 65% of grade 5 torques. b. for flange whizlock nuts and screws - use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings, all torque values must meet this specification. Common Hardware Types Hex Head Capscrew Washer Standard Hardware Sizing When a washer or nut is identified as 1/2 (M8), this is the Nominal size, meaning the inside diameter is 1/2 inch (8mm metric thread diameter); if a second number is present it represents the threads per inch (distance between threads). Carriage Bolt Wrench & Fastener Size Guide Lockwasher Hex Nut When bolt or capscrew is identified as 1/2-16 x 2 (M x 50 ), this means the Nominal size, or body diameter is 1/2 inch (8mm metric thread diameter), the second number,16, represents the threads per inch, (1.25 thread diameter). The final number is the body length of the bolt or screw, 2 inches (50mm). 1/4 Bolt or Nut Wrench 7/16 M6 Bolt or Nut Wrench 10mm 5/16 Bolt or Nut Wrench 1/2 M8 Bolt or Nut Wrench 13mm 3/8 Bolt or Nut Wrench 9/16 M10 Bolt or Nut Wrench 17mm 7/16 Bolt or Nut Wrench (Bolt) 5/8 Wrench (Nut) 11/16 M12 Bolt or Nut Wrench 19mm 1/2 Bolt or Nut Wrench 3/4 M14 Bolt or Nut Wrench 22 mm

36 IT IS THE POLICY OF BRIGGS & STRATTON CORP. TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS. Briggs & Stratton Yard Power Products Group 3515 N. 124 Street / PO Box 702 Wauwatosa, WI USA

Reproduction. Not for. Mid Frame Dual Stage Snowthrower. Parts Manual

Reproduction. Not for. Mid Frame Dual Stage Snowthrower. Parts Manual Parts Manual Attachment Mfg. No. Description 1695994 (I924EX), 9TP 24" Snowthrower (CE/Export) Mid Frame Dual Stage Snowthrower Not for Reproduction Manual Part No. Revision - Rev. Date: 7/20/2011 Table