Reproduction. Not for. Large Frame Dual Stage Snowthrowers. Parts Manual

Transcription

1 Parts Manual Attachment Mfg. No. Description (SIH1428SE), 14.5TP 28" Dual Stage Snowthrower (CE/Export) Large Frame Dual Stage Snowthrowers (SIH1730SE), 16.5TP 30" Dual Stage Snowthrower (CE/Export) (H1226E), 11.5TP 26" Dual Stage Snowthrower (H1528E), 14.5TP 28" Dual Stage Snowthrower (H1730E), 16.5GT 30" Dual Stage Snowthrower Revision - Manual Part No. Rev. Date: 10/1/2012

2

3 Table Of Contents PRODUCT COMPONENTS PAGES Handles & Controls Group... 4 Engine & Frame Group TP, 14.5TP & 16.5TP... 8 Auger Drive Group Auger Housing Group Traction Drive Group - General Transmission Transmission SERVICE PARTS - General Transmission H Wheels & Tires Group Decals Group Chute & Rotation Group - Full Electric Gear Case Assembly Torque Specification Chart... Inside Back Cover

4 Handles & Controls Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

5 Handles & Controls Group REF NO PART NO. QTY. DESCRIPTION YP 1 HEADLIGHT ASSEMBLY * BULB, Headlight, Halogen, V 27W (Included with Ref. No. 0010) CYP 1 COVER, Panel SM 8 SCREW, Truss Head Torx, 1/4-20 x 3/ SM 1 SCREW, Truss Head Torx, 1/4-20 x 3/ CABLE AND SPRING ASSEMBLY, Auger Drive, Right AYP 1 HANDLE, Lower AYP 1 HANDLE, Upper, Right AYP 1 HANDLE, Upper, Left YP 2 CAPSCREW, Hex Head, 5/16-18 x 3/4 G SM 2 NUT, Hex Flange, Two Way Lock, 5/ YP 4 KNOB, Wing, 5/ YP 2 BOLT, Carriage, 5/16-18 x 2-1/4 G SM 4 WASHER, Internal Tooth, 5/ SM 5 NUT, Hex Lock, ESNA Light, 1/ SM 2 SPACER, 1/4ID x 3/8OD SM 4 CAPSCREW, Hex Head, 1/4-20 x 1-3/4 G AYP 1 LEVER, Clutch, Right AYP 1 LEVER, Clutch, Left BMYP 1 BRACKET, Pivot, Free Hand YP 1 ROD, 5-5/8 Inch SM 1 SPACER, 1/4ID x 3/8OD YP 2 SPACER, Stepped YP 2 BOLT, Shoulder, 1/4 x 1-1/ SM 3 NUT, Hex Lock, Nylon Insert, YP 2 GRIP, Heated (Used on 28" & 30" Domestic Models Only) SM 2 HAND GRIP SCREW (Used on 28" & 30" Domestic Models Only) SM 2 NUT, Hex, 5/ LOCKWASHER, Split, 5/ YP 1 BALL JOINT YP 1 ROD, Speed Select SM 1 CAPSCREW, Hex Head, 3/8-16 x 2 G SM 3 NUT, Hex Flange, Whiz Lock, 5/ MA 1 SPRING SM 1 WASHER, 3/ SM 1 NUT, Hex Lock, Esna Light, 3/ YP 1 BRACKET, Controls SM 1 SCREW, Phillips, #10-24 x 3/ SM 1 GRIP, Lever SM 2 NUT, Hex Lock Nylon Insert, SPEED LEVER YP 1 ROD & SPRING ASSEMBLY SM 2 SPRING, Compression Footnotes Note* See your local hardware store for replacement bulbs. 5

6 Handles & Controls Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

7 Handles & Controls Group REF NO PART NO. QTY. DESCRIPTION YP 2 CAPSCREW, Hex Head, 1/4-20 x 1-3/4, G SM 4 NUT, Nylock Flange, 1/4-20, G MA 3 BOLT, Carriage, 5/16-18 x 3/ BMYP 1 COVER, Dash SM 5 TIE, Self Lock YP 1 WIRE HARNESS, Deflector YP 1 WIRE HARNESS, Heated Hand Grip (Used on 28" & 30" Domestic Models Only) YP 1 SWITCH, Heated Hand Grip (Used on 28" & 30" Domestic Models Only) BMYP 1 BRACKET, Mounting, RH BMYP 1 BRACKET, Mounting, RH AYP 1 POD, Chute Rotation, RH AYP 1 POD, Deflector, LH BMYP 1 BRACKET, Heated Hand Grip (Used on 28" & 30" Domestic Models Only) WASHER, Flat, 1/ YP 1 BRACE BOLT, Carriage, 1/4-20 x 3/ SM 1 SCREW, Hex Washer Head, Taptite, 1/4-20 x 3/ YP 2 CABLE, Steering Control YP 1 CABLE, Traction Drive BOLT, Oval Head, x 1-1/ BOLT, Carriage, 5/16-18 x 2 Footnotes Note* See your local hardware store for replacement bulbs. 7

8 Engine & Frame Group TP, 14.5TP & 16.5TP NOTE: Unless noted otherwise, use the standard hardware torque specification chart

9 Engine & Frame Group TP, 14.5TP & 16.5TP REF NO PART NO. QTY. DESCRIPTION C F81 * ENGINE, 11.5TP Briggs & Stratton, Domestic (Engine Model: 15C F8) M F11 * ENGINE, 14.5TP Briggs & Stratton, Domestic (Engine Model: 20M F1) M H 1 * ENGINE, 14.5TP Briggs & Stratton, Export (Engine Model: 20M H1) M F11 * ENGINE, 16.5TP Briggs & Stratton, Domestic (Engine Model: 21M F1) M H 1 * ENGINE, 16.5TP Briggs & Stratton, Export (Engine Model: 21M H1) * CAP, Fuel (Use on Domestic Models) * CAP, Fuel (Use on CE/Export Models) * GUARD, Muffler, Plate (Use on 11.5TP only) * GUARD, Muffler, Plate (Use on 14.5TP & 16.5TP Domestic Models) * GUARD, Muffler, Wire (Use on 14.5TP & 16.5TP CE/Export Models) * SCREW, Muffler Guard (Use on 11.5TP only) * SCREW, Muffler Guard * HOSE, Oil Drain MA 1 CORD, 10FT, 110V (Use on Domestic Models Only) GS 4 SCREW, Hex Head, Trilobular, 3/8-16 x 1-1/ YP 1 PULLEY SM 1 LOCKWASHER, Spring, 3/8 (Use on 14.5TP & 16.5TP only) LOCKWASHER, Spring, 5/16 (Use on 11.5TP only) CAPSCREW, Hex Head, 3/8-24 x 1-3/4, G8 (Use on 14.5TP & 16.5TP only) YP 1 CAPSCREW, Hex Head, 5/16-24 x 1-3/4 (Use on 11.5TP only) SM 1 KEY, Parallel, 3/16 x 3/16 x 1-1/ YP 1 V-BELT, Multi-Speed YP 1 PULLEY YP 1 V-BELT, 4L, 38.35, Auger YP 1 STOP, Belt NUT, Hex, KEPS, 5/ SM 1 BOLT, Carrige, 5/16-18 x 1, G WASHER, Flat, 1/ SPACER, 1/4 x.118, G YP 1 BELLCRANK AYP 1 BRACKET, Lower YP 1 BRACKET, Support, Auger Idler BMYP 1 BRACKET, Guide Wheel CAPSCREW, Hex Head, 1/4-20 x 1-1/2, G MA 1 SPOOL CABLE, Auger Control NUT, Flange, Serrated, 1/4-20, G MA 1 IDLER, Plastic Ball Bearing NUT, Centerlock, 3/ BOLT, Carriage, 3/8-16 x 1-1/ SM 1 WASHER, Thrust, 1/2 ID x 1 OD YP 1 AUGER IDLER SM 2 WASHER, 1/ SM 1 ARM, Control PIN, Hair, 3/32 x 1.60, G5 Footnotes Note* To verify your specific engine model, please reference the ID Tag located on your engine. See your local Briggs & Stratton distributor for parts and service. 9

10 Engine & Frame Group TP, 14.5TP & 16.5TP NOTE: Unless noted otherwise, use the standard hardware torque specification chart

11 Engine & Frame Group TP, 14.5TP & 16.5TP REF NO PART NO. QTY. DESCRIPTION PIN, Clevis BMYP 1 PANEL, Bottom SCREW, Hex Washer Head, Thread Roll, 1/4-20 x 5/ YP 1 SPRING, Torsion CYP 1 FRAME CYP 1 PLATE, Engine (Use on 14.5TP & 16.5TP only) CYP 1 PLATE, Engine (Use on 11.5TP only) SCREW, Hex Washer Head, Thread Roll, 5/16-18 x 3/ YP 1 COVER, Belt YP 2 SCREW, Hex Washer Head, Taptite, SEMS, 1/4-20 x 3/ SM 1 PIN, Cotter, Self Locking, 1/4 Footnotes Note* To verify your specific engine model, please reference the ID Tag located on your engine. See your local Briggs & Stratton distributor for parts and service. 11

12 Auger Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

13 Auger Drive Group REF NO PART NO. QTY YP MA AYP YP SM SM SM YP SM BMYP BMYP BMYP BMYP SM X79MA DESCRIPTION PIN, Sheer, 1/4 x 1-3/4 PIN, Cotter, Bow Tie, 3/16 GEAR CASE ASSEMBLY KEY, Square, 3/16 x 3/4 IMPELLER HUB, Impeller SCREW, Hex Washer Head, Taptite, 5/16-18 x 1/2 SET SCREW, Square Head, 5/16-18 x 1/2 SET SCREW, Square Head, 5/16-18 x 5/8 (Use on 26" Model) PULLEY, Auger SPACER, Auger (Use on 26" Model) AUGER ASSEMBLY, 28, LH AUGER ASSEMBLY, 24, LH (Use on 26" Model) AUGER ASSEMBLY, 28, LH AUGER ASSEMBLY, 24, RH (Use on 26" Model) FITTING, Zerk BOLT, Carriage, 5/16-18 x 3/4, G5 NUT, Flange, 5/16-18, G5 WASHER, 3/4 ID x 1 OD Footnotes 13

14 Auger Housing Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

15 Auger Housing Group REF NO PART NO. QTY YP YP YP BMYP BMYP BMYP SM YP SM X146MA YP SM YP SM SM BMYP 2 DESCRIPTION AUGER HOUSING, 26" AUGER HOUSING, 28" AUGER HOUSING, 30" NUT, Nylock Flange, 5/16-18 SCRAPER BAR, 26" SCRAPER BAR, 28" SCRAPER BAR, 30" BOLT, Carriage, 5/16-18 x 5/8, G5 (Qty 7 Used on 28 & 30" Models) NUT, Hex Flange, 5/16-18 (Qty 7 Used on 28 & 30" Models) BOLT, Carriage, 3/8-16 x 1-1/4,G5 SKID SHOE NUT, Hex Flange, ESNA, 3/8-16 BEARING, Flange SCREW, Hex Washer Head, Taptite, 5/16-18x x 1-1/4 NUT, Nylock, #10-24 CLAMP, Retainer SCREW, Truss Head Torx, #10-24 x 3/8 BRUSH, Cleanout BEARING, Ball RETAINER, Ball Bearing BOLT, Carriage, 5/16-18 x 3/4, G5 COVER, Bushing Footnotes 15

16 Traction Drive Group - General Transmission NOTE: Unless noted otherwise, use the standard hardware torque specification chart

17 Traction Drive Group - General Transmission REF NO PART NO. QTY. DESCRIPTION YP 1 TRANSMISSION, General Transmission H AYP 2 BRACKET SM 4 CAPSCREW, Hex Head, 3/8C x 2-3/4 GR SM 4 NUT, Hex Jam, 3/ YP 1 ROD, Speed Select SM 2 COTTER PIN, 1/4" Self Locking YP 1 TUBE, Support YP 2 GEAR, Drive YP 2 AXLE SM 4 NUT, Hex Flange, Whiz Lock Large, 3/ YP 2 RETAINER, Bearing MA 2 BEARING, Ball YP 2 RING, Retaining YP 4 RETAINER, Bolt 3/8" SM 4 SCREW, Hex Washer Head Taptite, 5/16-18 X 3/ YP 4 BOLT, Carriage, FH GR 5, 3/8-16 x 3/4 Footnotes Note* See Transmission Assembly Group for detailed service parts. 17

18 Transmission SERVICE PARTS - General Transmission H2 NOTE: Unless noted otherwise, use the standard hardware torque specification chart

19 Transmission SERVICE PARTS - General Transmission H2 REF NO PART NO. QTY. DESCRIPTION YP 1 TRANSMISSION, Complete General Transmission H YP 2 SPRING, Traction, 8.75 Inches YP 1 SCREW, 5 X YP 1 WASHER, 5.3 X 15 X 1.2.ipt YP 1 LEVER YP 1 CAM, Control YP 1 SPRING, Variator YP 1 SHIFT ARM YP 1 PULLEY ASSEMBLY YP 1 SCREW, M8x20 left YP 1 WASHER, 25 X 35 X YP 1 BEARING, RS YP 2 GEAR YP 2 RETAINER YP 1 WASHER, 0.8 X 27 X YP 4 SCREW, 4 X YP 2 NUT YP 2 BOLT, Allen-Head, CHC M5 X YP 2 PIN YP 4 WASHER, Starlock Footnotes 19

20 Wheels & Tires Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

21 Wheels & Tires Group REF NO PART NO. QTY YP YP YP YP SM MA DESCRIPTION WHEEL ASSEMBLY, , P2-578, LH (Use on 26" & 28" Models) WHEEL ASSMEBLY, 16 x 6.50, P2-578, LH (Use on 30" Models) WHEEL ASSEMBLY, , P2-578, RH (Use on 26" & 28" Models) WHEEL ASSMEBLY, 16 x 6.50, P2-578, RH (Use on 30" Models) VALVE STEM & CAP (Included on 0010 & 0020) BOLT, Hex Head, 1/4-20 x 1-3/4, G5 NUT, Nylock, 1/4-20 Footnotes 21

22 Decals Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

23 Decals Group REF NO PART NO. QTY YP YP YP YP YP SM YP YP YP YP YP YP SM SM YP YP YP YP 1 DESCRIPTION DECAL, Dash Operation DECAL, Gear Shift DECAL, Foot, FR/Eng (Domestic) DECAL, Danger Auger Icons (Export) DECAL, Chute Warning, FR/ENG (Domestic) DECAL, Chute Warning (Export) DECAL, Dash, Logo DECAL, Model H1226E DECAL, Model H1528E DECAL, Model SIH1528SE DECAL, Model H1730E DECAL, Model SIH1730SE DECAL, Logo, Housing, 25" (Use on 26" & 28" Models) DECAL, Logo, Housing, 27" (Use on 30") DECAL, Auger Control Symbols DECAL, Traction Control Symbols DECAL, Do Not Shift (Domestic) DECAL, Do Not Shift, No Text (Export) Footnotes 23

24 Chute & Rotation Group - Full Electric NOTE: Unless noted otherwise, use the standard hardware torque specification chart

25 Chute & Rotation Group - Full Electric REF NO PART NO. QTY. DESCRIPTION SM 1 PINION, 1-1/4 Lg YP 3 SCREW, Torx Button Head, M5 x.8 x SM 3 WASHER, Flat, 7/32 x 1/ SM 1 CAPSCREW, Hex Washer, Taptite, 1/4-20 x 3/ YP 1 COVER, Electric Chute Rotation SM 3 RETAINER, Spout SM 6 CAPSCREW, Hex Washer, x 5/ YP 1 SWITCH, Chute Rotation SM 1 TIE, Self Locking, 7-5/16 Lg SM 2 DECAL, Hinge CYP 1 CHUTE ASSEMBLY, Tall, Steel YP 1 MOTOR, Spout Rotator, 38" BMYP 1 GEAR, Tall, Steel Chute SM 3 BOLT, Carriage, 1/4-20 x 3/4, G SM 3 NUT, Hex Flange, 1/ BMYP 1 BRACKET ASSEMBLY YP 1 MOTOR, Chute Deflector SM 2 SCREW, Truss Head, Torx, 1/4-20 X 3/ SM 2 NUT, Hex Flange, 1/ YP 1 SWITCH, Deflector Control YP 1 WASHER, Rubber YP 1 NUT, 1/4-20, L.H SM 1 WASHER, 1/ SM 1 GUARD, Chute (CE/Export) SM 2 PUSHNUT, 3/16 Dia. (CE/Export) AYP 1 BRACKET, Chute Guard (CE/Export) SM 2 CAPSCREW, Hex Washer, Taptite, 1/4-20 x 1/2 (CE/Export) YP 2 GROMMET, Chute Guard Bracket (CE/Export) Footnotes 25

26 Gear Case Assembly NOTE: Unless noted otherwise, use the standard hardware torque specification chart

27 Gear Case Assembly REF NO PART NO. QTY SM SM SM SM SM SM YP SM SM SM SM SM SM SM SM SM SM SM SM SM SM SM SM SM 1 DESCRIPTION CAPSCREW, 1/4-20 x 2-3/4 CAPSCREW, 1/4-20 x 2-1/4 GEAR CASE, Left TAPERED PIPE PLUG GASKET SHAFT, Auger Cutoff SHAFT, Worm Cutoff SEAL, Oil FLANGE BUSHING PIN, Drive Lock THRUST COLLAR ROLLED WORM CASE WASHER, Thrust WASHER, Thrust GEAR, Worm GEAR CASE, Right NUT, Top Lock Flange, 1/4-20 SEAL BRACKET, Wireform KEY, Woodruff BUSHING TUBE KEY, Woodruff NUT, Flange, 1/4-20 Footnotes 27

28

29

30

31 Hardware Identification & Torque Specifications Torque Specification Chart FOR STANDARD METRIC MACHINE HARDWARE (Tolerance ± 20%) Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Property Class 5.6 Class Class 8.8 Class 10.9 Class 12.9 Size Of in/lbs in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. M M M M M M M M M M M M M M M M M M M The guides and ruler furnished below are designed to help you select the appropriate hardware Inside Diameter (in) Nut, 1/2-16 1/4 1/2 3/ /4 1/2 3/ Thread Diameter (mm) Body Diameter 2 Screw, 1/2-16 x 2 1/4 1/2 3/ Body Diameter Nut, M8 Screw, M x 25 Thread Diameter (mm) Threads per inch Body Length Distance between threads (mm) Threads per inch /4 1/2 3/4 Body Length (mm) Body Length (in) 4 Hardware Grade No Marks SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm / / / / / / / / / / / / / / / / / / , ,000 1,360.0 NOTES 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. for prevailing torque locknuts - use 65% of grade 5 torques. b. for flange whizlock nuts and screws - use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings, all torque values must meet this specification. Common Hardware Types Hex Head Capscrew Washer Standard Hardware Sizing When a washer or nut is identified as 1/2 (M8), this is the Nominal size, meaning the inside diameter is 1/2 inch (8mm metric thread diameter); if a second number is present it represents the threads per inch (distance between threads). Carriage Bolt Wrench & Fastener Size Guide Lockwasher Hex Nut When bolt or capscrew is identified as 1/2-16 x 2 (M x 50 ), this means the Nominal size, or body diameter is 1/2 inch (8mm metric thread diameter), the second number,16, represents the threads per inch, (1.25 thread diameter). The final number is the body length of the bolt or screw, 2 inches (50mm). 1/4 Bolt or Nut Wrench 7/16 M6 Bolt or Nut Wrench 10mm 5/16 Bolt or Nut Wrench 1/2 M8 Bolt or Nut Wrench 13mm 3/8 Bolt or Nut Wrench 9/16 M10 Bolt or Nut Wrench 17mm 7/16 Bolt or Nut Wrench (Bolt) 5/8 Wrench (Nut) 11/16 M12 Bolt or Nut Wrench 19mm 1/2 Bolt or Nut Wrench 3/4 M14 Bolt or Nut Wrench 22 mm

32 IT IS THE POLICY OF BRIGGS & STRATTON CORP. TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS. Briggs & Stratton Yard Power Products Group 3515 N. 124 Street / PO Box 702 Wauwatosa, WI USA