CENTURY 5130 / 5230 INSTALLATION, OPERATION, MAINTENANCE & PARTS

Transcription

1 CENTURY L E G E N D A R Y L E A D E R S H I P OWNER'S MANUAL 5130 / 5230 INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice All ratings specified are based on structural factors only, not vehicle capacities or capabilities. CENTURY Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee FORM NO / 01 Phone (423) FAX (423) PRICE $25.00

2 LIMITED WARRANTY MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in service, whichever is earlier. MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless authorized by MILLER. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from any general or particular requirement which MILLER knew or had reason to know about at the time of sale. MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty. MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through changes in design or materials as it may deem desirable without being obligated to incorporate such changes in products previously sold. This warranty is not intended to cover or include the following items, which are set forth by way of example and not limitation: A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather, road conditions, road treatments, etc. B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide reasonable and necessary maintenance, or uses for which the equipment was not designed or intended. C. Alterations or modifications that affect performance, operation or reliability. D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts. IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER IMPROPER USE. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee SERIAL NUMBER Telephone (423)

3 Section VI - PARTS This Section is provided by the manufacturer for the purpose of ordering any component part of the CENTURY 5130 or 5230 that may be required when part replacement is necessary. Be certain to use only original equipment replacement parts for warranty purposes as well as for keeping your CENTURY 5130 or 5230 in its original state and optimum operating capacities. When ordering replacement or spare parts be sure to provide the following information to the manufacturer s Parts Department. 1. Manual Number & Date of Publication 2. Manual Page Number 3. Page Title 4. Reference Number of Part Desired 5. Part Number 6. Part Description 7. Quantity of Part Desired Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner. Should additional information be required for repair or replacement of certain components, contact your Manufacturer Authorized Representative. The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may change the specifications, models and feature availability. VI-1

4 SUBFRAME ASSEMBLY VI-2

5 SUBFRAME ASSEMBLY GREASE FITTING QUICK PIN BUSHING, 3-1/2" X 2-1/2" INTERNAL CENTER BONDED MOUNT SPECIAL WASHER RAMP PAD SAFETY CHAIN, SYSTEM 10 8 REF SPADE CYLINDER 9 REF LIFT CYLINDER SCREW, 1/4"-20 X 3/4" HEX HD CAP SCREW, 3/8"-16 X 1-1/4" FL HD SKT SCREW, 3/8"-16 X 1-1/2" HEX SKT SET SCREW, 1/2"-13 X 1-1/2" HEX HD CAP SCREW, 1/2"-13 X 4-1/2" HEX HD CAP SCREW, 5/8"-11 X 2" HEX HD CAP SCREW, 5/8"-11 X 4-1/2" HEX HD CAP SCREW, 3/4"-10 X 3-1/2" HEX HD CAP SCREW, 3/4"-10 X 2-1/2" HEX HD CAP SCREW, 3/4"-10 X 6-1/2" HEX HD CAP NUT, 3/8"-16 NYLOK HEX NUT, 1/2"-13 NYLOK HEX NUT, 5/8"-11 NYLOK HEX NUT, 3/4"-10 NYLOK HEX NUT, 3/4"-10 NYLOK HEX LOCKWASHER, 1/4" HELICAL WASHER, 5/8" FLAT LOCKWASHER, 5/8" HELICAL WASHER, 3/4" FLAT (5230) SPRING PIN, 1/4" X 2-1/2" SPADE BLADE SHAFT, LOWER SPADE PIN, LIFT CYLINDER SHAFT, UPPER SPADE BOLTING PLATE PIN, SPADE PIVOT COVER PLATE, SPADE FRONT BODY MTG TUBE (5130) FRONT BODY MTG TUBE WELDMENT (5230) PIVOT PIN, LIFT CYLINDER LOWER SPADE PAD WELDMENT PIN, MULTI-POSITION LEFT INNER SPADE WELDMENT RIGHT INNER SPADE WELDMENT BRACKET, BOOM PIVOT SUBFRAME WELDMENT VI-3

6 STANDARD BODY ASSEMBLY VI-4

7 STANDARD BODY ASSEMBLY FT RUBBER FENDER MUDFLAP DOOR CHECK, 11" 4 7 FT "D" GASKET (NOT SHOWN) BACKUP ALARM (NOT SHOWN) TOOL BOX, 156" C.A. LT STEEL SINGLE TOOL BOX, 156" C.A. RT STEEL SINGLE SCREW, #6-32 X 1/2" RD HD PH SCREW, 1/4"-20 X 3/4" MACH SCREW, 1/4"-20 X 3/4" HEX HD CAP SCREW, 5/16"-18 X 1" RD HD MACH SCREW, 3/8"-16 X 1-1/4" HEX HD CAP NUT, 1/4"-20 NYLOK HEX CLIP, 1/4" TINNERMAN NUT, 3/8"-16 NYLOK HEX WASHER, 1/4" FLAT RIVET, 1/4" NUT, #6-32 HEX MUDFLAP MTG ANGLE, LEFT MUDFLAP MTG ANGLE, RIGHT BAR, MUDFLAP RETAINING STRIP, RUBBER FENDER PANEL, SWITCH PANEL, CONTROL PANEL, CONTROL PANEL, GAUGE SPACER PLATE, STEEL (NOT SHOWN) GASKET, BASE ANGLE (NOT SHOWN) GASKET (NOT SHOWN) CENTURY NAMEPLATE KIT SCREW, #10-24 X 1/2" OVAL HD SS CENTURY NAMEPLATE BODY MOUNTING HARDWARE (NOT SHOWN) SCREW, 3/4"-10 X 2-1/2" HEX HD CAP SCREW, 7/8"-9 X 2-1/2" HEX HD CAP NUT, 3/4"-10 NYLOK HEX NUT, 7/8"-9 NYLOK HEX KIT, TOOL BOX HOLE PLUG (NOT SHOWN) RUBBER WASHER SCREW, 1/2"-13 X 1-1/2" CRGBLT NUT, 1/2"-13 HEX LOCKWASHER, 1/2" HELICAL WASHER, 1/2" FLAT WASHER, 5/8" FLAT LIGHT BAR, STANDARD GASKET, LIGHT BAR SCREW, 3/8"-16 X 1" HEX HD CAP SCREW, 1/2"-13 X 1-1/4" HEX HD CAP SCREW, 1/2"-13 X 1-1/2" HEX HD CAP NUT, 3/8"-16 NYLOK HEX NUT, 1/2"-13 NYLOK HEX WASHER, 1/2" FLAT SUPPORT, L.H. VERTICAL SUPPORT, R.H. VERTICAL MOUNTING BRACKET TOP CHANNEL AERODYNAMIC LIGHT PYLON LIGHT RACK SCREW, 3/8"-16 X 1-3/4" HEX HD CAP NUT, 3/8"-16 NYLOK HEX WASHER, 3/8" FLAT LIGHT PYLON, MOUNTING RUBBER BODY MOUNTING KIT (NOT SHOWN) ANGLE, TAILGATE MOUNTING MOUNTING PLATE MOUNTING PLATE SPACER, REAR FRAME BRACKET VI-5

8 STANDARD BODY ASSEMBLY VI-6

9 STANDARD BODY ASSEMBLY FT RUBBER FENDER MUDFLAP DOOR CHECK, 11" 4 7 FT "D" GASKET (NOT SHOWN) BACKUP ALARM (NOT SHOWN) FT DOOR SEAL (NOT SHOWN) TOOL BOX, 156" C.B. LT ALUM TANDEM TOOL BOX, 156" C.B. RT ALUM TANDEM SCREW, #6-32 X 1/2" RD HD PH SCREW, 1/4"-20 X 3/4" MACH SCREW, 1/4"-20 X 3/4" HEX HD CAP SCREW, 5/16"-18 X 1" RD HD MACH SCREW, 3/8"-16 X 1-1/4" HEX HD CAP NUT, 1/4"-20 NYLOK HEX CLIP, 1/4" TINNERMAN NUT, 3/8"-16 NYLOK HEX WASHER, 1/4" FLAT RIVET, 1/4" NUT, #6-32 HEX MUDFLAP MTG ANGLE, RT MUDFLAP MTG ANGLE, LT BAR, MUDFLAP RETAINING STRIP, RUBBER FENDER PANEL, SWITCH PANEL, CONTROL PANEL, CONTROL PANEL, GAUGE MOUNTING PLATE (NOT SHOWN) SPACER PLATE, ALUMINUM (NOT SHOWN) GASKET, BASE ANGLE (NOT SHOWN) GASKET (NOT SHOWN) CROSSMEMBER, ALUMINUM BODY (NOT SHOWN) CENTURY NAMEPLATE KIT SCREW, #10-24 X 1/2" OVAL HD SS CENTURY NAMEPLATE BODY MOUNTING KIT (NOT SHOWN) ANGLE, TAILGATE MOUNTING MOUNTING PLATE MOUNTING PLATE SPACER, REAR FRAME BRACKET BODY MOUNTING HARDWARE (NOT SHOWN) SCREW, 3/4"-10 X 2-1/2" HEX HD CAP SCREW, 7/8"-9 X 2-1/2" HEX HD CAP NUT, 3/4"-10 NYLOK HEX NUT, 7/8"-9 NYLOK HEX CHAIN RACK, ALUMINUM BODY (NOT SHOWN) SCREW, 3/8"-16 X 3" HEX HD CAP NUT, 3/8"-16 NYLOK HEX CHAIN HANGER WELDMENT TRAY KIT (NOT SHOWN) SCREW, 5/16"-18 X 1-1/4" SELF TAP SCREW, 3/8"-16 X 3" HEX HD CAP NUT, 3/8"-16 NYLOK HEX WASHER, 3/8" FLAT TRAY WELDMENT KIT, TOOL BOX HOLE PLUG (NOT SHOWN) RUBBER WASHER SCREW, 1/2"-13 X 1-1/2" CRGBLT NUT, 1/2"-13 HEX LOCKWASHER, 1/2" HELICAL WASHER, 1/2" FLAT WASHER, 5/8" FLAT LIGHT BAR, STANDARD (REFER TO PAGE VI-4 & VI-5) AERODYNAMIC LIGHT PYLON (REFER TO PAGE VI-4 & VI-5) VI-7

10 RECOVERY BOOM ASSEMBLY VI-8

11 RECOVERY BOOM ASSEMBLY GREASE FITTING SHEAVE, 8" GREASE FITTING, STR 1/8" 4 14 FT SYNFLEX HOSE, 3/8" SNAP RING, 1-1/2" INTERNAL WEAR PAD PIPE PLUG, 4 AL PLUG WIRE ROPE, 5/8" X 200' 6x37 IWRC XIPS SCREW, 3/8"-16 X 3/4" HEX HD CAP SCREW, 3/8"-16 X 1-1/2" HEX HD CAP SCREW, 3/8"-16 X 3" HEX HD CAP SCREW, 3/8"-16 X 2-1/2" HEX HD CAP SCREW, 1/2"-13 X 5-1/2" HEX HD CAP NUT, 3/8"-16 NYLOK HEX NUT, 1/2"-13 NYLOK HEX LOCKWASHER, 3/8" HELICAL ROLL PIN, 3/8" X 1" CABLE GUIDE, BOTTOM PLATE, WINCH CABLE SUPPORT PIN PIVOT PIN, BOOM SHAFT, SHEAVE CABLE GUIDE SWIVEL WELDMENT OUTER BOOM WELDMENT INNER BOOM WELDMENT CONNECTOR, 3/8" TUBE X 1/8" NPT BULKHEAD COUPLING, 1/8" ELBOW, 1/4" NPT X 3/8" TUBE SCREW, #10-32 X 5/8" PAN HD PH HD SCREW, 3/8"-16 X 1" FL SKT HD RETAINING RING, 1-1/2" LUBRICATOR MOUNTING PLATE WEAR PAD, UPPER PAD RETAINING PLATE, UPPER PAD SPIDER CLAMP WELDMENT, TOP 37 REF EXTEND CYLINDER WEAR PAD, LOWER PIN, EXTEND CYLINDER 40 2 DE1381 1/2 WASHER VI-9

12 UNDERLIFT & TOWER ASSEMBLY VI-10

13 UNDERLIFT & TOWER ASSEMBLY SNAP RING 1" GREASE FITTING COMPRESSION SPRING, CROSS BAR DETENT BALL, 1-3/16" "O" RING, PIVOT PIN SPRING BUSHING SLIDE PAD BUSHING, PIVOT PIN THRUST WASHER, 1/8" THRUST WASHER, 1/16" SNAP RING 1-1/4" PIPE PLUG, 4 AL PLUG FOLD CYLINDER WEAR PAD TILT CYLINDER EXTEND CYLINDER SCREW, 3/8"-16 X 3" HEX HD CAP SCREW, 3/8"-16 X 1-1/2" HEX SKT SET SCREW, 3/8"-24 X 5/8" HEX HD CAP SCREW, 3/8"-24 X 3/4" HEX HD CAP SCREW, 1/2"-13 X 1" HEX HD CAP SCREW, 3/8"-24 X 5/8" BUTTON HD SKT SCREW, 5/8"-11 X 4-1/2" SKT HD CAP NUT, 3/8"-16 NYLOK HEX LOCKWASHER, 3/8" EXTERNAL TOOTH LOCKWASHER, 3/8" HELICAL LOCKWASHER, 1/2" HELICAL LOCKWASHER, 5/8" HELICAL BOLT-ON SPACER PAD SPACER PAD BOLT-ON BEARING PAD STOP PLATE PIN, FOLD CYLINDER ROD END SPACER, DETENT BALL SPRING PIVOT PIN, TOP HALF PIVOT PIN, BOTTOM HALF SHAFT, EXTEND CYLINDER (ROD) SHAFT, EXTEND CYLINDER (BASE) SHAFT, TILT CYLINDER SHAFT, TILT CYLINDER PIN, UNDERLIFT PIVOT TOWER PIVOT PIN WELDMENT PIN, FOLD CYLINDER BASE CROSSBAR WELDMENT TOWER WELDMENT RD STAGE BOOM WELDMENT OUTER BOOM WELDMENT ND STAGE BOOM WELDMENT 49 2 BK2003 WEAR PAD 50 2 RB0205 SPLIT, BUSHING KIT, WINCH CABLE STOW (NOT SHOWN) SCREW, 5/8"-11 X 4" HEX HD CAP NUT, 5/8"-11 NYLOK HEX WELDLESS CHAIN LINK, 5/8" CABLE TIE-BACK SPRING VI-11

14 UNDERLIFT HYDRAULICS VI-12

15 UNDERLIFT HYDRAULICS CONNECTOR, 6MJ-8MB ELBOW, 6MJ-4MP BRANCH TEE, 6MJ-6MJ-4MP CONNECTOR, 6MJ-6MP ELBOW, 6MJ-8MP HOSE ASSEMBLY, 18" CONNECTOR, 6MJ-6MB HOSE CLAMP, INSULATED 5/8" ELBOW, 6MJ-6MB DOUBLE HOLDING VALVE HOLDING VALVE IN-LINE ORIFICE HOSE ASSEMBLY, 24" HOSE ASSEMBLY, 18" ADAPTER, 8MJ-6MJ CLAMPING UNIT SPLIT BUSHING, 1/2" STACKING NUT, SKT HD HOSE ASSEMBLY, 34" HOSE ASSEMBLY, 44" HOSE ASSEMBLY, 44" TUBE ASSEMBLY HOSE ASSEMBLY, 72" HOSE ASSEMBLY, 10" HOSE ASSEMBLY, 108" HOSE ASSEMBLY, 108" TEE, 8MJ-8MJ-8MB HOSE ASSEMBLY, 32" HOSE ASSEMBLY, 18" CONNECTOR, 8MB-6FB CONTROL VALVE, VDP11CDDDC HOSE ASSEMBLY, 18" FOLD CYLINDER TILT CYLINDER EXTEND CYLINDER SCREW, 1/4"-20 X 2" HEX HD CAP NUT, 1/4"-20 NYLOK HEX SCREW, 5/16"-18 X 3/4" HEX HD CAP WASHER, 1/4" FLAT BRACKET, CHECK VALVE MOUNTING VI-13

16 RECOVERY BOOM HYDRAULICS VI-14

17 RECOVERY BOOM HYDRAULICS CONNECTOR, 6MJ-8MB GREASE FITTING HOSE ASSEMBLY, 72" ELBOW, 6MJ-8MB CONNECTOR, 6MJ-6MB BULKHEAD RUN TEE W/NUT HOSE ASSEMBLY, 54" CONNECTOR, 8MB-6FB CONTROL VALVE, VDP11DDDC HOSE ASSEMBLY, 46" HOSE ASSEMBLY, 46" CYLINDER, BOOM LIFT CONNECTOR, 8MJ-6MB CYLINDER, EXTEND VI-15

18 PUMP, VALVE & FILTER HYDRAULICS VI-16

19 PUMP, VALVE & FILTER HYDRAULICS ELBOW, 6MJ-6FJX HOSE ASSEMBLY, 131" GAUGE, FLUSH MOUNT 6000 PSI CONNECTOR, 6MJ-4FP HOSE ASSEMBLY, 73" PUMP, BI-ROTATIONAL HOSE BRACKET (NOT SHOWN) PUMP KIT PIPE NIPPLE, 1-1/2" X 5" CLAMP HOSE, 1" - 2-1/4" HOSE ASSEMBLY, 120" CONNECTOR, 8MJ-8MJ (NOT SHOWN) HOSE ASSEMBLY, 58" (NOT SHOWN) ELBOW, 8MJ-12MB BALL VALVE, BRONZE HOSE BARB, 20HOSE-20MP FT SUCTION HOSE, 1-1/4" ADAPTER, 16MB-12FB (NOT SHOWN) STREET ELBOW, /2" (NOT SHOWN) CLAMP, 2-1/2" INSULATED (NOT SHOWN) BUSHING, 24MP-20FP (NOT SHOWN) HOSE BARB, 20HOSE-16MB SCREW, 1/2"-13 X 1-1/2" HEX HD CAP LOCKWASHER, 1/2" HELICAL VALVE PAN ASSEMBLY CONTROL VALVE, VDP11DDDC ELBOW, 8MJ-10MB ELBOW, 12MJ-12MB STRAIGHT ADAPTER, 8FJ-6MJ RUN TEE, 8MJ-8FJX-8MJ CONTROL VALVE, VDP11CDDDC SCREW, 1/4"-20 X 2" HEX HD CAP SCREW, 5/16"-18 X 1" HEX HD CAP SCREW, 3/8"-16 X 4-1/2" HEX HD CAP SCREW, 3/8"-16 X 1-3/4" HEX HD CAP NUT, 1/4"-20 NYLOK HEX NUT, 5/16"-18 NYLOK HEX NUT, 5/16"-24 NYLOK HEX NUT, 3/8"-16 NYLOK HEX WASHER, 1/4" FLAT WASHER, 3/8" FLAT SPACER, CONTROL VALVE PLATE, CONTROL BULKHEAD PLATE, CONTROL BULKHEAD PLATE VALVE MOUNTING PLATE VALVE MOUNTING RESERVOIR ASSEMBLY RETURN LINE FILTER ASSEMBLY CLAMP HOSE, 1" - 2-1/4" PIPE PLUG, 3/4" NPT MALE ELBOW, 12MJ-12MP CENTER BONDED MOUNT SPECIAL WASHER SIGHT GAUGE FT SUCTION HOSE, 1-1/4" FILLER CAP SCREW, #10-32 X 1" RD HD MACH SCREW, 3/8"-16 X 1-1/4" HEX HD CAP SCREW, 3/8"-16 X 2-1/2" HEX HD CAP NUT, #10-32 NYLOK HEX NUT, 3/8"-16 NYLOK HEX LOCKWASHER, 3/8"HELICAL GASKET, CLEAN OUT & FILLER COVER FILLER PIPE WELDMENT RESERVOIR SUPPORT WELDMENT RESERVOIR WELDMENT, LEFT RESERVOIR WELDMENT, RIGHT COVER KIT SCREW, 3/8"-16 X 3/4" HEX HD CAP NUT, 3/8"-16 NYLOK HEX SUPPORT, COVER COVER, VALVE VI-17

20 WINCH HYDRAULICS & AIR FREE SPOOL VI-18

21 WINCH HYDRAULICS & AIR FREE SPOOL CONNECTOR, 8MJ-8MB ELBOW, 8MJ-8MB FT AIR HOSE, 1/4" O.D HOSE ASSEMBLY, 84" CABLE TIE, 4" (NOT SHOWN) 6 40 FT CONVOLUTED LOOM, 1/4" ELBOW, 8MJ-8MB90LL CLAMPING UNIT SPLIT BUSHING, 3/4" STACKING NUT, SKT HD CONTROL VALVE, VDP11DDDC CONTROL VALVE, VDP11CDDDC HOSE ASSEMBLY, 110" SCREW, 5/16"-18 x 3/4" HEX HD CAP SCREW, 5/8"-11 x 2-1/2" HEX HD CAP NUT, 5/8"-11 HEX NYLOK ANGLE, WINCH MOUNTING ANGLE, WINCH MOUNTING ANGLE, WINCH MOUNTING ANGLE, WINCH MOUNTING ELBOW, 4TB-4MP WINCH, 25K DP VI-19

22 LEFT CONTROL ASSEMBLY VI-20

23 LEFT CONTROL ASSEMBLY REMOTE CONTROL ASSEMBLY CONTROL KNOB, (IN/OUT) CONTROL KNOB, BOOM (UP/DOWN) CONTROL KNOB, JACK (UP/DOWN) CONTROL KNOB, BOOM (IN/OUT) CONTROL CABLE, 104" GREASE FITTING, 1/4"-28 X CONTROL KNOB, TILT (UP/DOWN) CONTROL KNOB, W/L EXTEND (IN/OUT) ADJUSTABLE CLEVIS CONTROL KNOB, FOLD (UP/DOWN) CONTROL CABLE, 114" SCREW, #6-32 X 1/2" RD HD PH SCREW, 1/4"-20 X 3/4" HEX HD CAP SCREW, 5/16"-24 X 1-1/4" HEX HD CAP SCREW, 5/16"-18 X 2-1/2" HEX HD CAP NUT, 1/4"-20 HEX NYLOK NUT, 5/16"-18 "J" TINNERMAN NUT, 5/16"-18 HEX NYLOK NUT, 5/16"-24 HEX NUT, 3/8"-16 HEX NYLOK NUT, 3/8"-16 HEX JAM WASHER, 1/4" FLAT WASHER, 5/16" INTERNAL TOOTH WASHER, 3/4" FLAT (SPECIAL) CLEVIS PIN, 5/16" X 1" COTTER PIN, 3/32" X 1" NUT, #6-32 HEX CLAMP, SHAFT CONTROL BOX PLATE, SHAFT SUPPORT PIN, CONTROL BOX CONTROL CABLE CONNECTOR CONTROL HANDLE WELDMENT LEFT CONTROL FRAME WELDMENT REMOTE CONTROL ASSEMBLY / WIRE CONNECTOR, SPADE ELBOW, 4TB-4MP / AIR HOSE, 1/4" O.D. (FT.) 37 2 / CONNECTOR, 4TB-4MP 38 2 / BRASS PLUG, 4MP CABLE SEALING GRIP HEX PIPE BUSHING CONVOLUTED LOOM, 3/8" X 8" / CABLE TIE, 4" 18 LB / BREATHER VENT, 2MP / ELBOW, 4TB-2MP AIR SOLENOID VALVE (8) AIR SOLENOID VALVE (14) CIRCUIT BREAKER, HI-AMP WATERPROOF 47 1 / TERMINAL BLOCK POWER PAL, 15 POSITION POWER PAL, 8 POSITION 49 8 / ELECTRICAL CABLE, 16/10 SO (FT.) 50 4 / AIR CYLINDER AIR FILTER/REGULATOR AIR LUBRICATOR MOUNTING BRACKET 54 2 / SCREW, #8-32 X 3/4" RD HD SLOTTED 55 4 / SCREW, 1/4"-20 X 1-1/4" HEX HD CAP 56 2 / SCREW, 1/4"-20 X 2" HEX HD CAP 57 2 / HEX NUT & STAR WASHER, # / NUT, 1/4"-20 HEX NYLOK 59 4 / NUT, 7/16"-20 HEX JAM 60 2 / WASHER, 1/4" FLAT 61 4 / CLEVIS PIN, 5/16" X 5/8" COTTERLESS SUPPORT, SOLENOID VALVE (8) SUPPORT, SOLENOID VALVE (14) 63 4 / CLEVIS WELDMENT 64 1 HA0132 GAUGE, PSI VI-21

24 RIGHT CONTROL ASSEMBLY VI-22

25 RIGHT CONTROL ASSEMBLY CONTROL KNOB, (IN/OUT) CONTROL KNOB, BOOM (UP/DOWN) CONTROL KNOB, JACK (UP/DOWN) CONTROL KNOB, BOOM (IN/OUT) CONTROL CABLE, 104" GREASE FITTING, 1/4"-28 X ADJUSTABLE CLEVIS CONTROL CABLE, 114" SCREW, 5/16"-18 X 1-1/4" HEX HD CAP SCREW, 5/16"-18 X 2-1/2" HEX HD CAP NUT, 5/16"-18 "J" TINNERMAN NUT, 5/16"-18 HEX NYLOK NUT, 5/16"-24 HEX NUT, 3/8"-16 HEX JAM WASHER, 5/16" INTERNAL TOOTH WASHER, 3/4" FLAT (SPECIAL) CLEVIS PIN, 5/16" X 1" COTTER PIN, 3/32" X 1" CLAMP, SHAFT CONTROL BOX PIN, CONTROL BOX CONTROL HANDLE WELDMENT RIGHT CONTROL FRAME WELDMENT VI-23

26 REAR SPADE HYDRAULICS CONNECTOR, 6MJ-8MB HOSE CLAMP, 1" INSULATED CONNECTOR, 6MJ-6MB NIPPLE, BLACK PIPE, 1/2" X 4-1/2" CONNECTOR, 8MB-6FB 6 REF CONTROL VALVE, VDP11DDDC110 7 REF CONTROL VALVE, VDP11CDDDC HOSE ASSEMBLY, 136" SPADE CYLINDER ELBOW, 6MJ-8FP90 VI-24

27 HYDRAULIC CYLINDERS BOOM LIFT CYLINDER (COMPLETE) -- SEAL KIT, BOOM LIFT CYLINDER BOOM EXTEND CYLINDER (COMPLETE) -- SEAL KIT, BOOM EXTEND CYLINDER UNDERLIFT TILT CYLINDER (COMPLETE) -- SEAL KIT, UNDERLIFT TILT CYLINDER UNDERLIFT EXTEND CYLINDER (COMPLETE) -- SEAL KIT, UNDERIFT EXTEND CYLINDER UNDERLIFT FOLD CYLINDER (COMPLETE) -- SEAL KIT, UNDERLIFT FOLD CYLINDER REAR SPADE CYLINDER (COMPLETE) -- SEAL KIT, REAR SPADE CYLINDER VI-25

28 GLAD HAND KIT RECEPTACLE BOOT GLAD HAND COUPLING GLAD HAND PLUG BULKHEAD CONNECTOR ADAPTER, 1/4" NPM X 3/8" SYN. HOSE HD 7-WAY TRAILER CONNECTOR SCREW, 1/4"-20 X 1" HEX HD CAP NUT, 1/4"-20 HEX NYLOK WASHER, 1/4" FLAT WASHER, 5/16" FLAT AIR HOSE, 3/8" X 48" SYNFLEX VI-26

29 LIFT ADAPTERS FORK, SHORT (3" OPENING) FORK, SHORT (4-1/2" OPENING) FORK, MEDIUM (3" OPENING) FORK, MEDIUM (4-1/2" OPENING) FORK, LONG (3" OPENING) FORK, LONG (4-1/2" OPENING) FORK, OFFSET REAR AXLE TEE HANDLE, ALUMINUM 5/8" X 1-1/4" HAIR PIN COTTER, 1-1/4" BOLT, MODIFIED 5/8"-11 X 6" WITH HOLE TEE HANDLE, FORK ADAPTER CHAIN HOOK ADAPTER, RT CHAIN HOOK ADAPTER, LT PIVOT PIN LIFT BRACKET FORK ADAPTER, LT FORK ADAPTER, RT RETAINER PIN ASSEMBLY RETAINING PIN, SPRING LIFT BRACKET VI-27

30 KING PIN ADAPTER KING PIN ADAPTER WELDMENT FIFTH WHEEL ADAPTER (COMPLETE) ROLL PIN, 3/8" X 1-1/2" 3 2 HD1259 SNAPPER PIN 4 1 VA0660 FIFTH WHEEL PIVOT PLATE WELDMENT 5 1 VA0661 PULL PIN WELDMENT 6 1 VA0662 PIVOT PIN WELDMENT PINTLE HOOK KIT (COMPLETE) PINTLE HOOK (NOT SHOWN) SCREW, 1/2"-13 X 1" HEX HD CAP LOCKWASHER, 1/2" HELICAL TH WHEEL, KING PIN ADAPTER & PINTLE HOOK BRACKET WELDMENT RETAINING PIN ASSEMBLY VI-28

31 MODULAR WIRING KIT CONNECTOR,WIRE (BLUE 7520) CONNECTOR,WIRE (YELL 7530) RING CONN HEAT SHRINK TUBE-IN.MELT (BLACK) CABLE TIE, 7-50 LB ADHESIVE BACK TIE MOUNT WIRING HARNESS LT 5030T WIRING HARNESS RT 5030T FEMALE TERMINAL CONNECTOR, 6 WAY MALE CONNECTOR, 6 WAY FEMALE JUNCTION BOX, 10 POLE GROUND WIRE POS. TOWER (FEMALE) POS. SHROUD (MALE) CABLE SEAL, BLUE SCREW, 1/4"-20 X 1" HEX HD CAP NUT, 1/4"-20 NYLOK HEX KIT, BACK UP ALARM GV57 RUBBER GROMMET VI-29

32 MODULAR LIGHT KIT BRACKET, LICENSE PLATE RUBBER GROMMET LICENSE PLATE ILLUMINATOR LIGHT BAR ASSEMBLY 5 16 FT CLOSED CELL SPONGE, 3/4" X 1/8" RING CONN / HEAT SHRINK TUBE-IN.MELT (BLACK) BACK-UP LIGHT DOME LIGHT, M 390S MARKER LIGHT, AMBER TAIL LIGHT, LEFT TAIL LIGHT, RIGHT SCREW, #8-32 X 1" RD HD PHL MCH SCREW, #10-24 X 1" OVAL HD PHL MCH SCREW, #10-24 X 1/2" THRD CUT RD HD SS VI-30

33 NOTES

34 CENTURY Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee (423)