INSTALLATION, OPERATION, MAINTENANCE & PARTS

Transcription

1 CENTURY L E G E N D A R Y L E A D E R S H I P OWNER'S MANUAL 1624 INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice All ratings specified are based on structural factors only, not vehicle capacities or capabilities. CENTURY A Division of Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee FORM NO / 02 Phone (423) FAX (423) PRICE $25.00

2 LIMITED WARRANTY MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in service, whichever is earlier. MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless authorized by MILLER. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from any general or particular requirement which MILLER knew or had reason to know about at the time of sale. MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty. MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through changes in design or materials as it may deem desirable without being obligated to incorporate such changes in products previously sold. This warranty is not intended to cover or include the following items, which are set forth by way of example and not limitation: A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather, road conditions, road treatments, etc. B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide reasonable and necessary maintenance, or uses for which the equipment was not designed or intended. C. Alterations or modifications that affect performance, operation or reliability. D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts. IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER IMPROPER USE. Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee SERIAL NUMBER Telephone (423)

3 Section VI - PARTS LIST This Section is provided by the manufacturer for the purpose of ordering any component part of the CENTURY 1624 that may be required when part replacement is necessary. Be certain to use only original equipment replacement parts for warranty purposes as well as for keeping your CENTURY 1624 in its original state and optimum operating capacities. When ordering replacement or spare parts be sure to provide the following information to the manufacturer s Parts Department. 1. Manual Number & Date of Publication 2. Manual Page Number 3. Page Title 4. Reference Number of Part Desired 5. Part Number 6. Part Description 7. Quantity of Part Desired Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner without delay. Should additional information be required for repair or replacement of certain components, contact your Manufacturer Authorized Representative. The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may change the specifications, models and feature availability. VI-1

4 FINAL INSTALLATION KIT BOOM INSTALLATION UNDERLIFT & TOWER ASSEMBLY BODY ASSEMBLY " C.A SUBFRAME ASSEMBLY FINAL INSTALLATION KIT CABLE TIE, T120R BLK 15-1/4" CABLE TIE, 7" 50 LB WIRE ROPE, 1/2" X 6 X 37 IWRC PUMP, BI-ROTATIONAL KIT, BODY MOUNTING HARDWARE KIT, PUMP BRACKET, CROSSBAR SHEAVE ASSEMBLY PIN, CABLE ASSEMBLY KIT, FORK STORAGE KIT, BODY MOUNTING KIT, STANDARD 4024 FORK GROUND KIT MTG. HARNESS CENTURY KIT, BODY MOUNTING HARDWARE /4"-10 X 2.5" HHCS GR8 GOLD /4"-10 NYLOK HEX GR8 ZP KIT, PUMP HOSE CLAMP,.875" TO 2.75" HOSE ASSEMBLY, 120" FITTING, BARB 24C4-24MP HOSE, SUCTION 1-1/2" ID PIPE NIPPLE, 1-1/2" X 3" BALL VALVE FITTING, CONN 8MJ-16MB PLUG, 16MB PIPE, ELBOW, STREET 1.5" FITTING, ELBOW FITTING, HOSE BARB INSULATED CLAMP, 2 1/2" /2"-13 X 2" HHCS GR5 ZP /2"-13 NYLOK HEX NUT ZP BRACKET, CROSSBAR SHEAVE ASSEMBLY GREASE FITTING, 1/4"-28 STR SHEAVE, 8 58SHVBBAY 1.5" PINTLE HOOK VI-2

5 BRACKET, CROSSBAR SHEAVE ASSY (cont'd) /8"-16 X 3" HHCS GR5 ZP /2"-13 X 1.5" HHCS GR5 ZP /2"-13 X 1.25" HHCS GR5 ZP /8"-16 NYLOK HEX NUT ZP /2" HELICAL LOCKWASHER ZP (HD0695) SHAFT - SHEAVE BRACKET, CROSSBAR SHEAVE TH WHEEL & KING PIN ADAPTER PIN, RETAINING ASSEMBLY PIN, CABLE ASSEMBLY PIN, MOUNTING ASSEMBLY PIN, RETAINING ASSEMBLY PIN, RETAINING 1053 ZP SLEEVE, 1/16" DIA CABLE /16" CABLE ASSEMBLY 17" #10 X 1/2" DRIVE SCREW RD /8" X 3" ROLL PIN ZP TUBE, 14" PROTECTIVE HOSE PIN, RETAINER PIN, CABLE ASSEMBLY SLEEVE, 1/16" DIA CABLE /16" CABLE ASSEMBLY, 17" PIN, LYNCH #10 X 1/2" DRIVE SCREW RD /16" X 1" ROLL PIN ZP TUBE, 14" PROTECTIVE HOSE PIN, CABLE PIN, MOUNTING ASSEMBLY 62 1 HD1259 PIN, SNAPPER SLEEVE, 1/16" DIA CABLE /16" CABLE ASSEMBLY 17" /8" X 1-1/2" ROLL PIN ZP TUBE, 14" PROTECTIVE HOSE MOUNTING PIN WELDMENT PIN, CABLE ASSEMBLY SLEEVE, 1/16" DIA CABLE /16" CABLE ASSEMBLY, 17" PIN, LYNCH #10 X 1/2" DRIVE SCREW RD VI-3

6 PIN, CABLE ASSEMBLY (cont'd) /16" X 1" ROLL PIN ZP TUBE, 14" PROTECTIVE HOSE PIN, CABLE KIT, FORK STORAGE /8"-16 X 2.5" HHCS GR5 ZP /8"-16 NYLOK HEX NUT ZP /8" FLATWASHER ZP BRACKET, FORK STORAGE WELDMENT KIT, BODY MOUNTING ANGLE, TAILGATE MOUNTING PLATE, MOUNTING PLATE - MOUNTING KIT, STANDARD 4024 FORK FORK, SHORT 3" OPENING FORK, SHORT 4-1/2" OPENING FORK, MEDIUM 3" OPENING FORK, MEDIUM 4-1/2" OPENING FORK, LONG 3" OPENING FORK, LONG 4-1/2" OPENING FORK, OFFSET REAR AXLE ALUM T HANDLE, 5/8" X 1-1/4" /4" HAIR PIN COTTER" BOLT - MODIFIED ADAPTER, LT. CHAIN HOOK ADAPTER-RT. CHAIN HOOK BRACKET, PIVOT SPRING LIFT ADAPTER, L.H. OFFSET FORK ADAPTER, R.H. OFFSET FORK PIN, RETAINING, SPRING LIFT PIN, RETAINING ASSEMBLY PIN, RETAINING, SPRING LIFT SLEEVE, 1/16" DIA CABLE /16" CABLE ASSEMBLY 17" PIN, LYNCH #10 X 1/2" DRIVE SCREW RD /8" X 3" ROLL PIN ZP /16" X 1-1/4" ROLL PIN ZP TUBE, 14" PROTECTIVE HOSE PIN, RETAINER VI-4

7 PIN, RETAINING ASSEMBLY PIN, RETAINING 1053 ZP SLEEVE, 1/16" DIA CABLE /16" CABLE ASSEMBLY 17" #10 X 1/2" DRIVE SCREW RD /8" X 3" ROLL PIN ZP TUBE, 14" PROTECTIVE HOSE PIN, RETAINER GROUND KIT MTG. HARNESS CENTURY /8"-16 X 1 HHCS GR5 ZP /16"-18 NYLOK HEX NUT ZP /8" EXT.TOOTH LOCKWASHER /4" EXT.TOOTH LOCKWASHER /8"-16 NC HEX NUT 316 SS LUG, GROUNDING BOOM INSTALLATION DE1381 1/2 WASHER SAE 17/32" ID HOSE ASSEMBLY, 46" LG GREASE FITTING, STR 1/8" NPT CABLE TIE, 7" 50 LB ADAPTER, 8MJ-6MJ CLAMPING UNIT, C-PH CLAMPING UNIT (SET), HC SPLIT BUSHING RUBBER C-SB C-SB /4" SPLIT C-SN-10 SOCKET-HEAD C-WA-10 WELD ADAPTER " OD X 2" ID X 1.5" SPRG HYDRAULIC TUBING HOSE ASSEMBLY, 120" /4"-20 X 2" HHCS GR5 ZP /16"-18 X 3/4" HHCS GR5 ZP /8"-16 X 3.5" HHCS GR5 ZP /2"-13 X 3/4" HHCS GR /4"-20 NYLOK HEX NUT ZP /2" HELICAL LOCKWASHER ZP (HD0695) PIN, PIVOT - BOOM KIT, TILT CYLINDER 3224/T BOOM ASSEMBLY SWIVEL, BOOM ASSEMBLY VI-5

8 KIT, TILT CYLINDER 3224/T FITTING, CONNECTOR 8MJ-8MB GREASE FITTING,1/4-28 STRAIGHT FITTING, ELB 6MJ-8MB FITTING, CONN. 6MJ-6MB MJ-6MJ-6MB BRANCH TEE FITTING, HYD. 6MJ - 6MB HOSE ASSEMBLY, 18" 6FJX-6FJX -6M1T HOSE ASSEMBLY, 34" CYL HYD HOSE ASSEMBLY, 10" HOSE ASSEMBLY, 32" FITTING, CONNECTOR 4MB-6FB VALVE, HOLDING 4000 PSI SAE /4"-20 X 2" HHCS GR5 ZP /8"-16 X 3.5" HHCS GR5 ZP /4"-20 NYLOK HEX NUT ZP /8"-16 NYLOK HEX NUT ZP /4" SS FLAT WASHER MOUNTING BRACKET, CHECK VALVE BUSHING, TILT CYLINDER PIN, TILT CYLINDER BASE PIN, TILT CYLINDER ROD BOOM ASSEMBLY GREASE FITTING, 1/4"-28 STRAIGHT OUTER BOOM WELDMENT WINCH ASSEMBLY WINCH ASSEMBLY GROMMET, RUBBER VALVE, SOLENOID AIR CONTROL HOSE ASSEMBLY, 45" AIR CYLINDER A WINCH H-600 LT BREATHER VENT, 1/8 MP FITTING, TEE HOSE ASSEMBLY, 94" MOTOR, HYDRAULIC PARKER #8-32 X 1/2" RD HD PH MCH SC SS /8"-16 X 1.25" HHCS GR5 ZP /8"-16 X 1.5" HHCS GR5 ZP /16"-14 X 1.25" HHCS GR5 ZP /2"-13 X 1.5" SOC HD CP SC GR8 VI-6

9 WINCH ASSEMBLY 1624 (cont'd) /8"-11 X 2" HHCS GR5 ZP #8-32 HEX NUT & STAR WASHER ZP /8"-16 NYLOK HEX NUT ZP /8"-11 NYLOK HEX NUT ZP /4" FLAT WASHER ZP /16" HELICAL LOCKWASHER /8" SAE WASHER /8" FLAT WASHER ZP /16" X 1-1/4" CLEVIS PIN /8" X 3/4" COTTER PIN MOUNTING ANGLE FREESPOOL BRACKET, LEFT COVER, FREESPOOL ANGLE, WINCH MOUNTING YOKE, ADJUSTMENT TENSIONER, CABLE FITTING, BRASS ELB 1/4T-1/8MPX FITTING, BRASS ELB 1/4T-1/4MP TENSIONER, CABLE SPRING COMPRESSION MH /8"-16 X 1.25" HHCS GR5 ZP /8"-16 X 1.5" HHCS GR5 ZP /8"-16 NYLOK HEX NUT ZP /2"-13 NYLOK HEX NUT ZP /8" FLAT WASHER ZP /2" FLAT WASHER ZP /8" X 3/4" COTTER PIN ROD, PIVOT CHANNEL, SPRING PIN, SPRING BRACKET, CABLE TENSIONER BRACKET, MOUNTING SWIVEL, BOOM ASSEMBLY GREASE FITTING, 1/4"-28 STR SHEAVE, 8 58SHVBBAY 1.5" /8"-16 X 3" HHCS GR5 ZP /8"-16 X 2.5" HHCS GR5 ZP /8"-16 NYLOK HEX NUT ZP GUIDE, BOTTOM CABLE SHAFT - SHEAVE GUIDE-CABLE VI-7

10 SWIVEL, BOOM ASSEMBLY (cont'd) BOOM END SWIVEL WELDMENT UNDERLIFT & TOWER ASSEMBLY GREASE FITTING, 1/4"-28 STR HOSE ASSEMBLY, 81" 4C2AT HOSE CLAMP, INSUL, 5/8" CYLINDER, BOOM FOLD FITTING, ELB 45 DEG /8"-16 X 3/4" HHCS GR5 ZP /8"-16 X 1.25" HHCS GR5 ZP /2"-13 X 1" HHCS GR5 ZP /8"-16 NYLOK HEX NUT ZP /8" FLAT WASHER ZP /8" HELICAL LOCKWASHER ZP /2" HELICAL LOCKWASHER ZP (HD0695) /2" FLAT WASHER ZP BLOCK, STOP BAR PIN, PIVOT 3224 U/L PIN, FOLD CYL. WELDMENT TOWER WELDMENT, 3224/T PIN, PIVOT WELDMENT CABLE TIE BACK WELDMENT HORIZONAL BOOM, ASSEMBLY CROSSBAR ASSEMBLY KIT, WINCH CABLE STOW HORIZONAL BOOM ASSEMBLY HD86 EXT CYL PIN WELDMENT HD89 RING, RETAINING, 1-5/16" GREASE FITTING, 1/4"-28 STR FITTING, CONN 6MJ-6MB HOSE ASSEMBLY, 107" SLIDE PAD " OD X 2" ID X 1.5" SPRG U/L EXTEND CYL /16"-18 X 2.5" HHCS GR5 ZP /8"-24 X 3/4" HHCS GR5 ZP /8"-24 X 5/8" BUTTON HEAD /16"-18 NYLOK HEX NUT ZP /8" EXT TOOTH LOCKWASHER PLATE, STOP PIN, EXT CYL BASE END VI-8

11 HORIZONAL BOOM ASSEMBLY (cont'd) PAD, SPACER BOOM-U/L OUTER WELDMENT BOOM-2ND STAGE U/L WELDMENT BOOM-INNER U/L ASSEMBLY BOOM-INNER U/L ASSEMBLY BUSHING BOOM, 3RD STAGE U/L WELDMENT CROSSBAR ASSEMBLY COMP SPRING, CROSSBAR, FI /16" DIA STEEL BALL "O" RING PIVOT PIN THRUST WASHER, 1/8" THK THRUST WASHER, 1/16" THK /8"-11 X 3.5" SKT HD CAP SCREW PIN, PIVOT, TOP HALF PIN, PIVOT, BOTTOM HALF SPACER, DETENT SPRING CROSSBAR WELDMENT KIT, WINCH CABLE STOW /8"-11 X4" HHCS GR5 ZP /8"-11 NYLOK HEX NUT ZP /8" WELDLESS CHAIN LINK CABLE TIE BACK SPRING BODY ASSEMBLY " C.A TOOL BOX, LT AL 138" C.A TOOL BOX, RT AL 138" C.A DOOR SEAL FLAG, AMERICAN LT ANGLE, MUDFLAP MTG.LEFT ANGLE, MUDFLAP MTG.RIGHT KIT, CENTURY NAMEPLATE KIT, LARGE WRECKER MUDFLAP KIT, RUBBER FENDER KIT, MODULAR WIRING KIT, MODULAR MOUNTS KIT, LIGHT1624 VI-9

12 KIT, CENTURY NAMEPLATE #10-24 X 1/2" OVAL HD SS NAMEPLATE, CENTURY, METAL KIT, LARGE WRECKER MUDFLAP MUD FLAP, 820 EXP /8"-16 X 1.25" HHCS GR5 ZP /8"-16 NYLOK HEX NUT ZP BAR, MUDFLAP KIT, RUBBER FENDER GSX-170 GRM /4" RIVET AD810BS STRIP, RETAINING KIT, MODULAR WIRING GV57 RUBBER GROMMET, ATLANTIC CONNECTOR, WIRE (BLUE 7520) CONNECTOR, WIRE (YELL 7530) #10 RING CONNECTOR GA HEAT SHRINK TUBE, IN. MELT (BLACK) CABLE TIE, 7" 50 LB ADHESIVE BACK TIE MOUNT WIRING HARNESS, LT 5030T WIRING HARNESS, RT 5030T FEMALE TERMINAL CONNECTOR, 6 WAY MALE CONNECTOR, 6 WAY FEMALE JUNCTION BOX, 10 POLE GROUND WIRE POS. TOWER (FEMALE) POS. SHROUD (MALE) CABLE SEAL, BLUE /4"-20 X 1" HHCS GR5 ZP /4"-20 NYLOK HEX NUT ZP KIT, BACK UP ALARM GROUND KIT, BODY HARNESS KIT, BACK UP ALARM WIRE, 16 GA RED CONNECTOR,WIRE (BLUE 7520) HEAT SHRINK TUBE, IN MELT (BLACK) BACK UP ALARM, ECCO MS /4"-20 X 1.25" HHCS VI-10

13 KIT, BACK UP ALARM (cont'd) /4"-20 NYLOK HEX NUT ZP INSTALLATION INSTRUCTION, BACKUP ALARM GROUND KIT, BODY HARNESS CABLE TIE, 7" 50 LB GROUND CABLE, 42" /16"-18 NYLOK HEX NUT ZP /8" EXT. TOOTH LOCKWASHER /8"-16 NC X 1-1/4" HHCS SS /8"-16 NC HEX NUT 316 SS KIT, MODULAR MOUNTS CENTER BONDED MOUNT SQUARE WASHER, 3" X 3" X.25 25/32" D GASKET, H2 ADHESIVE /8"-16 X 3.5" HHCS GR5 ZP /8"-11 X 4.5" HHCS GR 5 ZP /4"-10 X 3.5" HHCS GR5 ZP /4"-10 X 6.5" HHCS GR5 ZP /8"-16 NYLOK HEX NUT ZP /4"-10 NYLOK HEX NUT ZP /8" FLAT WASHER ZP /8" HELICAL LOCKWASHER ZP /4" FLAT WASHER ZP PLATE, MOUNTING PLATE, COVER TUBE, FRONT BODY MTG WELDMENT KIT, HOLE PLUG TOOL BOX KIT, HOLE PLUG TOOL BOX WASHER, RUBBER 7/16" X 1-1/4" X 1/4" /2"-13 X 1.5" CARRIAGE BOLT GR5 ZP /2"-13 HEX NUT ZP /2" HELICAL LOCKWASHER ZP (HD0695) /2" FLAT WASHER ZP /8" FLAT WASHER ZP KIT, LIGHT LICENSE PLATE BRACKET (LT0117) GROMMET, RUBBER LICENSE PLATE ILLUMINATOR LIGHT, 3 BAR ( ) /4" X 1/8" CLOSED CELL VI-11

14 KIT, LIGHT1624 (cont'd) #10 RING CONNECTOR GA GROMMET MTG KIT W/PLUG SEALED MARKER LIGHT, RED HEAT SHRINK TUBE, IN. MELT (BLACK) BACK-UP LIGHT LIGHT, RED, TAIL LIGHT, CLEAR LIGHT, M 390S DOME LIGHT, AMBER (3 PLUG RT ANGLE) #8-32 X 1" RD PHL HD MCH SC #10-32 X 1/2" THRD CUT RD S/S SUBFRAME ASSEMBLY /4"-10 X 2.75" HHCS GR8 GOLD /4"-10 NYLOK HEX GR8 ZP BAR PLATE, BOLTING SUBFRAME WELDMENT, BRACKET, BOOM PIVOT KIT, INLINE FILTER KIT, TOWER RAMP KIT, CONTROL VALVE KIT, TANK KIT, FRAME HYDRAULIC KIT, LIFT CYLINDER KIT, 1624 COVER PKG, CONTROL KNOB KIT, 1624 FRAME KIT, POWER PAL 8POS 12VDC SAFETY CHAIN ASSEMBLY RIGHT SIDE CONTROLS, KIT, INLINE FILTER FITTING, ELB 8MJ-12MB IN-LINE FILTER, PARKER /4"-20 X 3.5" HHCS GR5 ZP /16"-18 X 1.25" HHCS GR5 ZP /4"-20 NYLOK HEX NUT ZP /16"-18 NYLOK HEX NUT ZP /4" FLAT WASHER ZP ANGLE, FILTER MOUNTING VI-12

15 KIT, TOWER RAMP RAMP PAD, /8"-16 X 1.25" FLAT HD SOC /8"-16 NYLOK HEX NUT ZP KIT, CONTROL VALVE FITTING, HYD CONNECTOR 6MJ-8MB FITTING, ELB 8MJ-10MB FITTING, HP CARRY-OVER FITTING, ELL 8MJ - 8MB FITTING, ELB 12MJ-12MB BRACKET, CONTROL HANDLE FITTING, CONNECTOR 8MJ-12MB FITTING, ELL 8MJ-8MB90LL VALVE, 5 SPOOL /8"-16 X 5" HHCS GR5 ZP /8"-16 NYLOK HEX NUT ZP /16" SAE PLAIN WASHER ZP /32" X 1" COTTER PIN /16" X 3/4" COTTER PIN /8" X 3/4" COTTER PIN PIN, CONTROL HANDLE PIVOT SPACER, CONTROL VALVE HANDLE, CONTROL WELDMENT HANDLE, CONTROL WELDMENT HANDLE, CONTROL WELDMENT HANDLE, CONTROL WELDMENT HANDLE, CONTROL WELDMENT KIT, TANK FITTING, HOSE BARB, RETURN LINE FILTER ASSEMBLY FITTING, 90 DEG STREET ELL 3/4" /4" NPT PIPE PLUG, MALE CENTER BONDED MOUNT SPECIAL WASHER SIGHT GAUGE PIPE PLUG, 1-1/2" SQ HD PIPE, 3/4" BLACK CAP FILLER CAP (GO205, FB194) #10-32 X 1" RD HD MCH HD SCR ZP /8"-16 X 1.25" HHCS GR5 ZP /8"-16 X 2.5" HHCS GR5 ZP #10-32 NYLOK HEX NUT ZP VI-13

16 KIT, TANK 1624 (cont'd) /8"-16 NYLOK HEX NUT ZP /8" HELICAL LOCKWASHER ZP PLATE, COVER GASKET, CLEANOUT & FILLER COVER RESERVOIR WELDMENT, KIT, FRAME HYDRAULIC FITTING, CONNECTOR 8MJ-8MB FITTING, HYD CONNECTOR 6MJ-8MB FITTING, ELB 6MJ-4MP HOSE ASSEMBLY, 120" FITTING, ELL, 8MJ-8MB FITTING, MALE CONNECTOR KIT, FRAME HYDRAULIC FITTING, ELB 6MJ-8MB HOSE ASSEMBLY, 18" LG HOT WIRE, UNDER DASH HOOKUP FITTING, CONNECTOR 6MJ-6MB SWITCH BOX, IN CAB DT SOLENOID VALVE SHUTTLE VALVE, - RACINE HOSE ASSEMBLY, 25" FITTING, 45 DEG ELB FITTING, TEE 6MJ-6MJ-6FJX FITTING, BULKHEAD RUN TEE HOSE ASSEMBLY, 36" HOSE ASSEMBLY, 36" HOSE ASSEMBLY, 54" HOSE ASSEMBLY, 34" HARNESS WIRING HOSE ASSEMBLY, 10" HOSE ASSEMBLY, 18" LG SOLENOID VALVE, RACINE HOSE ASSEMBLY, 120" FITTING, CONNECTOR HOSE ASSEMBLY, 75" HOSE ASSEMBLY, 75" LG HOSE ASSEMBLY, 50" LG HOSE ASSEMBLY, 33" LG HOSE ASSEMBLY, 19" HOSE ASSEMBLY, 29" HOSE ASSEMBLY, 29" VI-14

17 KIT, FRAME HYDRAULIC 1624 (cont'd) HOSE ASSEMBLY, 34" HOSE ASSEMBLY, 34" HOSE ASSEMBLY, 52" /4"-20 X 2" HHCS GR5 ZP /4"-20 X 3.5" HHCS GR5 ZP /16"-18 X 1.25" HHCS GR5 ZP /8"-16 X 1.25" HHCS GR5 ZP /8"-16 X 4.5" HHCS GR5 ZP /4"-20 NYLOK HEX NUT ZP /16"-18 NYLOK HEX NUT ZP /8"-16 NYLOK HEX NUT ZP /4" FLAT WASHER ZP KIT, LIFT CYLINDER GREASE FITTING, 1/4"-28 STR PLUG, 1/2" SAE O-RING CLAMP, CHK VALVE RET 6-1/2" FITTING, ELL, 8MJ-8MB FITTING, ELB 6MJ-8MB FITTING, CONNECTOR 6MJ-6MB FITTING, HYD. 6MJ-6MB HOSE ASSEMBLY, 18" 6FJX-6FJX -6M1T FITTING, ELB 90 DEG HYDRAULIC TUBING FITTING, TEE 6MJ-6MJ-6FJX HOSE ASSEMBLY, 36" HOSE ASSEMBLY, 40" CYL HYD BOOM LIFT, FITTING, CONNECTOR 4MB-6FB VALVE, HOLDING 4000 PSI SAE /4"-20 X 2" HHCS GR5 ZP /8"-16 X 3" HHCS GR5 ZP /4"-20 NYLOK HEX NUT ZP /8"-16 NYLOK HEX NUT ZP /4" FLAT WASHER ZP MTG BRACKET, CHECK VALVE PIN, LIFT CYL BASE KIT, 1624 COVER COVER, CONTROL ALUM COVER, CONTROL COVER, RIGHT CONTROL CONTROL PANEL WELDMENT, 1624 VI-15

18 KIT, 1624 COVER (cont'd) TIMBER BOX, WELDMENT PKG, CONTROL KNOB KNOB, BLACK W/L XBAR CTRL KNOB, RED CTRL (IN-OUT) KNOB, BOOM (UP-DOWN) KNOB, TILT, 3/8"-16 THREAD KNOB, WHL LIFT EXT IN-OUT KIT, 1624 FRAME TOGGLE BOOT SEAL CENTER BONDED MOUNT HARNESS, GROUND CABLE SWITCH, TOGGLE FOR 316W KIT, POWER PAL 8POS 12VDC AMP CIRCUIT BREAKER HARNESS, 8 FUNCTION POWER POWER PAL HPDC08 8 FUNCTION BOLT, SS 1/4"-20 NC X 1" HHCS /4" SS FLAT WASHER /4"-20 NC SS NYLOCK NUT MARKER BRACKET RING TERM GA 10 ST SAFETY CHAIN ASSEMBLY SAFETY CHAIN, SYSTEM /8"-11 X 2" HHCS GR5 ZP /8"-11 NYLOK HEX NUT ZP /8" FLAT WASHER ZP RIGHT SIDE CONTROLS, HD0900 BEARING, ROD END 1/4" KNOB, RED CONTROL (IN-OUT) KNOB, BOOM (UP-DOWN) KNOB, BOOM (IN-OUT) BRACKET, CONTROL HANDLE CONTROL CABLE, 74" /8"-16 X 1" HHCS GR5 ZP /8"-16 NYLOK HEX NUT ZP /8"-16 HEX NUT JAM ZP /16" X 1" CLEVIS PIN ZP /16" X 3/4" COTTER PIN VI-16

19 RIGHT SIDE CONTROLS, 1624 (cont'd) /8" X 3/4" COTTER PIN PIN, CONTROL HANDLE PIVOT HANDLE, CONTROL WELDMENT HANDLE, CONTROL WELDMENT HANDLE, CONTROL WELDMENT HANDLE, CONTROL WELDMENT LINK, CONTROL WELDMENT MOUNT, 1624 CABLE HANDLE, CONTROL WELDMENT CONTROL PANEL WELDMENT VI-17

20 NOTES

21 NOTES

22 CENTURY Miller Industries Towing Equipment Inc Hilltop Drive Ooltewah, Tennessee (423)